XVR User's Manual V1.0.0 201703
XVR User's Manual V1.0.0 201703
XVR User's Manual V1.0.0 201703
V1.0.0
Table of Contents
i
3.5.1 Connecting Video Input.................................................................................................... 12
3.5.2 Connecting Video Output ................................................................................................ 13
ii
4.5.4 Auto Focus ......................................................................................................................... 35
4.5.5 Color ................................................................................................................................... 35
4.5.6 Display ................................................................................................................................ 37
4.5.7 Face Search ...................................................................................................................... 38
4.5.8 Search ................................................................................................................................ 38
4.5.9 Record Control .................................................................................................................. 38
4.5.10 Alarm Output ................................................................................................................. 38
4.5.11 Remote Device ............................................................................................................. 38
4.5.12 Video Matrix .................................................................................................................. 38
4.5.13 Main menu .................................................................................................................... 38
iii
4.10.3 Network ......................................................................................................................... 62
4.10.4 Log ................................................................................................................................. 65
iv
5.9 Information ............................................................................................................................ 256
v
Appendix B-3 Compatible Portable HDD list .............................................................................. 280
vi
Welcome
Thank you for purchasing our XVR DVR!
This user’s manual is designed to be a reference tool for the installation and operation of
your system.
Here you can find information about this series standalone DVR features and functions, as
well as a detailed menu tree.
Before installation and operation please read the following safeguards and warnings
carefully!
vii
Important Safeguards and Warnings
1.Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The product must be grounded to reduce the risk of electric shock.
We assume no liability or responsibility for all the fires or electrical shock caused by
improper handling or installation.
2.Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation,
storage and installation.
3.Installation
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted
repair.
5.Environment
The DVR should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Lithium battery
Improper battery use may result in fire, explosion, or personal injury!
When replace the battery, please make sure you are using the same model!
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
CAUTION
FOR YOUR OWN SAFETY, PLEASE CHANGE SYSTEM DEFAULT PASSWORD
AFTER YOU FIRST LOGIN!
viii
1 FEATURES AND SPECIFICATIONS
1.1 Overview
The standalone series DVR is an excellent digital monitor product designed for security
field.
This series device adopts embedded design to achieve high security and reliability. It can
work in the local end, and at the same time, when connecting it to the professional
surveillance software (PSS), it can connect to the security network to realize strong
network and remote monitor function.
This series product can be widely used in various areas such as banking,
telecommunication, electric power, interrogation, transportation, intelligent resident zone,
factory, warehouse, resources, and water conservancy.
1.2 Features
This series product has the following features:
Real-time surveillance
Support VGA port and HDMI port. Realize the surveillance through displayer. Support
HDMI, VGA, and TV output at the same time.
Storage function
Special data format to guarantee data security and can remove the risk of the vicious data
modification. Support digital watermark.
Compression format
Support multiple-channel audio and video. An independent hardware decodes the audio
and video signal from each channel to maintain video and audio synchronization.
Backup function
Support backup operation via USB port (such as U disk, portable HDD, burner)
Client-end user can download the file to local HDD to backup via network.
1
Support each channel real-time record independently, and at the same time it can support
search, forward play, network monitor, record search, download and etc.
Support various playback modes: slow play, fast play, backward play and frame by frame
play.
Support time title overlay so that you can view event accurate occurred time
Support customized zoom function during the preview.
Network operation
Support network remote real-time monitor, remote record search and remote PTZ control.
Communication port
RS485 port can realize alarm input and PTZ control.
RS232 port can connect to keyboard to realize central control, and can also connect to PC
COM to upgrade system and realize maintenance, and matrix control.
Standard Ethernet port can realize network access function.
The dual-network port has the multiple-access, fault-tolerance, load-balance setup mode.
PTZ control
Support PTZ decoder via RS485.
Intelligent operation
Mouse operation function
In the menu, support copy and paste setup function
2
Figure 1-1
Serial Number Name Function
1 Power button Click it to boot up or shut down
the device.
2 Address Click it to input device number, so
that you can control it.
3
8 click this button to realize normal
playback.
In reverse playback click this
button to pause playback.
Esc. Go back to previous menu or
9 cancel current operation (close
upper interface or control)
10 Record Start or stop record manually
In record interface, working with
the direction buttons to select the
record channel.
Click this button for at least 1.5
seconds, system can go to the
Manual Record interface.
11 Direction keys Switch current activated control,
go to left or right.
In playback mode, it is to control
the playback process bar.
Aux function(such as switch the
PTZ menu)
12 Enter /menu key go to default button
go to the menu
13 Multiple-window switch Switch between multiple-window
and one-window.
14 Fn In 1-ch monitor mode: pop up
assistant function : PTZ control
and Video color.
Switch the PTZ control menu in
PTZ control interface.
In motion detection interface,
working with direction keys to
complete setup.
In text mode, click it to delete
character.
15 0-9 number key Input password, channel or
switch channel.
Shift is the button to switch the
input method.
4
When you have selected one menu item, left click mouse to view menu
content.
Implement the control operation.
Modify checkbox or motion detection status.
Click combo box to pop up drop down list
In input box, you can select input methods. Left click the corresponding
button on the panel you can input numeral/English character
(small/capitalized). Here ← stands for backspace button. _ stands for
space button.
When input special sign, you can click corresponding numeral in the
front panel to input. For example, click numeral 1 you can input“/” , or
you can click the numeral in the on-screen keyboard directly.
Double left Implement special control operation such as double click one item in
click mouse the file list to playback the video.
In multiple-window mode, double left click one channel to view in
full-window.
Double left click current video again to go back to previous
multiple-window mode.
5
Right click In real-time monitor mode, pops up shortcut menu: one-window,
mouse four-window, nine-window and sixteen-window, Pan/Tilt/Zoom, color
setting, search, record, alarm input, alarm output, main menu.
Among which, Pan/Tilt/Zoom and color setting applies for current
selected channel.
If you are in multiple-window mode, system automatically switches to
the corresponding channel.
6
2 Installation and Connections
Note: All the installation and operations here should conform to your local electric
safety rules.
Important
Shut down the device and then unplug the power cable before you open the case to
replace the HDD!
All figures listed below for reference only!
This series DVR has 1 to 8 HDDs (no limitation for capacity). Please use HDD of 7200rpm
or higher. Usually we do not recommend the HDD for the PC. You can refer to the
Appendix for recommended HDD brand.
Please follow the instructions listed below to install hard disk.
2.3.1 Smart Box Series
Please make sure the metal surface of the HDD is facing up when you are installing!
This series product has only one 2.5-inch SATA HDD.
Please follow the instructions below to install HDD.
7
○
1 Draw out the HDD bracket ○
2 Make sure the HDD metal ○
3 Put the HDD into the
device.
surface is facing up and then put
the HDD into the bracket
horizontally. After the HDD is in
the proper position, the columns
on the two sides can lock the
screw holes of the HDD to secure
it.
When you remove the HDD, please refer to the following figure to pull the spring up and
then remove the HDD.
○
1 . Loosen the screws of the upper ○
2 Fix four screws in the HDD ○
3 Place the HDD in
cover and side panel. (Turn just three rounds). accordance with the four holes in
the bottom.
8
○
4 Turn the device upside down and ○
5 Fix the HDD firmly. ○
6 Connect the HDD cable and
○
7 Put the cover in accordance with ○
8 Secure the screws in the rear panel and the side panel.
①Loosen the screws of the upper cover ②Fix four screws in the HDD (Turn ③ Place the HDD in accordance
and side panel. just three rounds). with the four holes in the bottom.
9
④ Turn the device upside down and ⑤Fix the HDD firmly. ⑥Connect the HDD cable and
then turn the screws in firmly. power cable.
⑦Put the cover in accordance with the ⑧Secure the screws in the rear panel
clip and then place the upper cover and the side panel.
back.
Important:
You can connect the HDD data cable and the power cable first and then fix the HDD
in the device.
Please pay attention to the front cover. It adopts the vertical sliding design. You need
to push the clip first and then put down.
2.3.4 1U Series
The 1U series DVR has two SATA HDDs.
① Loosen the screws of the upper ② Fix four screws in the HDD ③ Place the HDD in accordance
cover and side panel. Remove (Turn just three rounds). with the four holes in the bottom.
the cover.
10
④Turn the device upside down and ⑤Connect the HDD cable and ⑥Put the cover in accordance
then turn the screws in firmly. power cable. . with the clip and then place the
upper cover back. Secure the
screws in the rear panel and the
side panel.
○
1 Loosen the screws of the ○
2 Line up the HDD to the ○
3 Connect the one end of the HDD
upper cover. Remove the four holes of the HDD cable to the HDD.
cover. bracket. Use four screws to .
fix HDD.
○
4 Connect the other end of ○
5 Connect the power cable ○
6 Put the cover back and fix the
2.3.6 2U series
This series DVR max supports 8 SATA HDDs. Please use HDD of 7200rpm or higher.
11
HDD to the bottom bracket.
⑤Connect the power cable to the ⑥Put the cover back and fix the
○
4 Connect the other end of the
HDD. screws to secure firmly.
HDD cable to the mainboard.
Important:
If the HDD amount is less than four, you do not need to install the HDD bracket.
When there is a bracket, please make sure the installation direction of HDDs is the same.
12
explosive substances and etc.
The camera and the DVR should have the same grounding to ensure the normal
operation of the camera.
Guarantee stability and reliability of the transmission line BTTTB
Please use high quality, sound shielded BNC. Please select suitable BNC model
according to the transmission distance.
If the distance is too long, you should use twisted pair cable, and you can add video
compensation devices or use optical fiber to ensure video quality.
You should keep the video signal away from the strong electromagnetic interference,
especially the high tension current.
Keep connection lugs in well contact BTTTB
The signal line and shielded wire should be fixed firmly and in well connection. Avoid dry
joint, lap welding and oxidation.
BTTT
HDMI output.
System supports BNC, VGA and HDMI output at the same time.
When you are using pc-type monitor to replace the monitor, please pay attention to the
following points:
To defer aging, do not allow the pc monitor to run for a long time.
Regular demagnetization will keep device maintain proper status.
Keep it away from strong electromagnetic interference devices.
Using TV as video output device is not a reliable substitution method. You also need to
reduce the working hour and control the interference from power supply and other devices.
The low quality TV may result in device damage.
13
2.7 Alarm Input and Output Connection
Please read the followings before connecting.
1. Alarm input
a. Please make sure alarm input mode is grounding alarm input.
b. Grounding signal is needed for alarm input.
c. Alarm input needs the low level voltage signal.
d. Alarm input mode can be either NC (normal Open) or NO (Normal Close)
e. When you are connecting two DVRs or you are connecting one DVR and one other
device, please use a relay to separate them,
2. Alarm output
The alarm output port should not be connected to high power load directly (It shall be less
than 1A) to avoid high current which may result in relay damage. Please use the co
contactor to realize the connection between the alarm output port and the load.
14
Figure 2-1
1,2,3,4,5,6, ALARM 1 to ALARM 16. The alarm becomes active in low voltage.
7,8,9,10,11,
12,13,14,15,16
In the second line, There are six groups of normal open activation output (on/off button)
from the left to the
right:
NO1 C1,
NO2 C2,
NO3 C3,
NO4 C4,
NO5 C5,
NO6 C6.
CTRL 12V Control power output. For external alarm, you need to close the
device power to cancel the alarm.
Voltage current;500mA.
+12V Rated current.
Voltage current;500mA.
Earth cable.
485 A/B 485 communication port. They are used to control devices such as
decoder. 120Ω should be parallel connected between A, B lines if
there are too many PTZ decoders.
T+,T-,R+,R- They are four-wire full-duplex RS485 port
T+ T-: output wire
R+ R-: input wire
15
Please connect the NC port of the alarm sensor to the DVR alarm input(ALARM)
Use the same ground with that of DVR if you use external power to the alarm device.
Figure 2-2
2.7.3 Alarm Output Port
Provide external power to external alarm device.
To avoid overloading, please read the following relay parameters sheet carefully.
RS485 A/B cable is for the A/B cable of the PTZ decoder.
T+,T-,R+,R- are four-wire double duplex RS485 port.
T+ T-: output wire
R+ R-: input wire
Relay Specification
Model HFD23/005-1ZS HRB1-S-DC5V
Material of the touch AgNi+ gold-plating AuAg10/AgNi10/CuNi30
Rated switch
30V DC 1A/125V AC 0.5A 24V DC 1A/125V AC 2A
capacity
Maximum
62.5VA/30W 250VA/48W
Rating switch power
(Resistance Maximum
125V AC/60V DC 125V AC/60V DC
Load) switch voltage
Maximum
switch 2A 2A
currency
Between
400VAC 1 minute 500VAC 1 minute
touches
Insulation
Between touch
1000VAC 1 minute 1000VAC 1 minute
and winding
Turn-on Time 5ms max 5ms max
Turn-off Time 5ms max 5ms max
Longevity 1×107times ( 300 5×106 times ( 300
Mechanical
times/MIN) times/MIN)
1×105 times ( 30 2.5×104 times ( 30
Electrical
times/MIN) times/MIN)
16
Model HFD23/005-1ZS HRB1-S-DC5V
Working Temperature -30℃~+70℃ -40℃~+70℃
2.8 RS485
When the DVR receives a camera control command, it transmits that command up the coaxial
cable to the PTZ device. RS485 is a single-direction protocol; the PTZ device can’t return any
data to the unit. To enable the operation, connect the PTZ device to the RS485 (A,B) input on
the DVR.
Since RS485 is disabled by default for each camera, you must enable the PTZ settings first.
This series DVRs support multiple protocols such as Pelco-D, Pelco-P.
To connect PTZ devices to the DVR:
1. Connect RS485 A,B on the DVR rear panel.
2. Connect the other end of the cable to the proper pins in the connector on the camera.
3. Please follow the instructions to configure a camera to enable each PTZ device on the
DVR.
485 Port
Figure 2-3
17
3 Overview of Navigation and Controls
3.1 Boot up and Shutdown
3.1.1 Boot up
Before the boot up, please make sure:
The rated input voltage matches the device power on-off button. Please make sure
the power wire connection is OK. Then click the power on-off button.
Always use the stable current, if necessary UPS is a best alternative measure.
Please follow the steps listed below to boot up the device.
Connect the device to the monitor and then connect a mouse.
Connect power cable.
Click the power button at the front or rear panel and then boot up the device. After
device booted up, the system is in multiple-channel display mode by default.
3.1.2 Shutdown
Note
When you see corresponding dialogue box “System is shutting down…” Do not click
power on-off button directly.
Do not unplug the power cable or click power on-off button to shutdown device
directly when device is running (especially when it is recording.)
18
3.2.1 Set Password
For your own safety, please set your administrator default password after you first
boot up the device.
After system booted up, you can see the following interface if it is your first time to use or
you have restored default setup. See Figure 3-1. Please input a password and then input
again to set a password.
You can set security questions here to reset the password in case you forgot. System
supports customized setup. Please note you need to set two security questions at the
same time. When you reset the password, you need to answer these two security
questions too.
For reset information, please refer to chapter 3.2.2.
Figure 3-1
After you complete the setup, click OK button, system pops up the following interface for
you to confirm. Click OK button to exit. See Figure 3-2.
Figure 3-2
19
3.2.2 Reset Password
Once you forgot password, you can answer the security questions you set in chapter 3.2.1
to reset the password.
Figure 3-3
System pops up the following dialogue box, please answer the security questions and
then input the new password twice. See Figure 3-4.
Figure 3-4
20
Click Cancel/Next button, you can see system goes to login interface.
Tips
Check the box Startup button here, system goes to startup wizard again when it boots up
the next time.
Cancel the Startup button, system goes to the login interface directly when it boots up the
next time.
Figure 3-5
Click Cancel button or Next Step button, system goes to login interface. See Figure 3-6.
System consists of three accounts:
Username: admin. Password: admin. (administrator, local and network)
Username: 888888. Password: 888888. (administrator, local only)
Username: default. Password: default (hidden user). Hidden user “default” is for
system interior use only and can not be deleted. When there is no login user, hidden
user “default” automatically login. You can set some rights such as monitor for this
user so that you can view some channel view without login.
Figure 3-6
21
Caution
For security reason, please modify password after you first login.
Continuous three times login failure will result in system alarm and five times
login failure will result in account lock!
Please reboot the device or wait for 30 minutes to try again if your account has
been locked.
After input corresponding user name and password, you can click OK button. System
goes to the startup wizard.
When there are all analog channels, the startup wizard includes general, encode,
schedule, record control, network, P2P.
When there is an IP channel, the startup wizard includes general, network, P2P,
remote device and schedule.
Figure 3-7
Note
You can only see the remote device interface if you have set IP channel (Chapter
3.11.1.3.5)
Click Next button, you can go to network interface. See Figure 3-8.
22
For detailed information, please refer to chapter 3.10.3.
Figure 3-8
Click Next button, you can set P2P function. Scan the QR code, download the App to the
cellphone, you can use the smart phone to add the device. See Figure 3-9.
For detailed information, please refer to chapter3.11.2.15.
Figure 3-9
23
Now you can go to the remote device interface to add the camera to the corresponding
channel. See Figure 3-10.
For detailed information, please refer to chapter3.11.1.1.
Please note you can not see the following interface if there is no digital channel. You can
go to Main menu->Setting->Camera->Channel type to set IP channel first. Please refer to
chapter 3.11.1.3.5 for detailed setup information.
Figure 3-10
Click Next button, you can go to Encode interface. See Figure 3-11.
For detailed information, please refer to chapter 3.11.1.3.
24
Figure 3-11
Click Next button, you can go to Schedule interface. See Figure 3-12.
For detailed information, please refer to chapter 3.11.4.1.
Figure 3-12
25
Click Finish button, system pops up a dialogue box. Click the OK button, the startup
wizard is complete. See Figure 3-13.
Figure 3-13
Tips
Preview drag: If you want to change position of channel 1 and channel 2 when you
are previewing, you can left click mouse in the channel 1 and then drag to channel
2, release mouse you can switch channel 1 and channel 2 positions.
Use mouse middle button to control window split: You can use mouse middle
button to switch window split amount.
Please note you can not switch position of one analog channel and one digital
channel.
Preview Control
The preview control function has the following features.
Support preview playback.
In the preview desktop, system can playback previous 5-60 minutes record of
current channel. Please go to the Main Menu->General to set real-time
playback time.
Support drag and play function. You can use your mouse to select any
playback start time.
Support playback, pause and exit function.
26
Right now, system does not support slow playback and backward playback
function.
Support digital zoom function.
Support real-time backup function.
You can follow the contents listed below for the operation instruction.
Preview control interface
Move you mouse to the top center of the video of current channel, you can see system
pops up the preview control interface. See Figure 3-14 and Figure 3-15. If your mouse
stays in this area for more than 6 seconds and has no operation, the control bar
automatically hides.
1 2 3 4 5
1 2 3 4 6 7
1) Realtime playback
It is to playback the previous 5-60 minutes record of current channel.
Please go to the Main menu->Setting->->System->General to set real-time playback
time.
System may pop up a dialogue box if there is no such record in current channel.
2) Digital zoom
It is to zoom in specified zone of current channel. It supports zoom in function of
multiple-channel.
Figure 3-16
27
Put the middle button at the center of the zone you want to zoom in, and move the
mouse, you can view an interface shown as in Figure 3-17.
Figure 3-17
Right click mouse to cancel zoom and go back to the original interface.
3) Manual record function
It is to backup the video of current channel to the USB device. System can not backup
the video of multiple-channel at the same time.
Click button , system begins recording. Click it again, system stops recoridng. You
can find the record file on the flash disk.
4) Manual Snapshot
Click to snapshot 1-5 times. The snapshot file is saved on the USB device or HDD.
You can go to the Search interface (chapter 3.9.1) to view.
5) Mute (For analog channel only)
Click to mute. Click again to enable audio function when preview.
Please note this function is for one-window mode only.
6) Bidirectional talk (For digital channel only)
If the connected front-end device supports bidirectional talk function, you can click this
button. Click button to start bidirectional talk function the icon now is shown as .
Now the rest bidirectional talk buttons of digital channel becomes null too.
Click again, you can cancel bidirectional talk and the bidirectional talk buttons of
28
After you go to the corresponding interface, right click mouse to go back to the
upper-level.
Window split mode: You can select window amount and then select channels.
PTZ: Click it to go to PTZ interface.
Auto focus: Please make sure you connected network camera supports this function.
Color setting: Set video corresponding information.
Search: Click it to go to Search interface to search and playback a record file.
Record control: Enable/disable record channel.
Remote device: Click it to add remote device.
Main menu: Go to system main menu interface.
Figure 3-18
3.5.1 Window Switch
System supports 1/4/8/9-window (The options here depend on your product channel
amount). You can select from the dropdown list. See Figure 3-19.
29
Figure 3-19
3.5.2 Previous Screen/Next Screen
Click it to go to the previous screen/next screen. For example, if you are using 4-split
mode, the first screen is displaying the channel 1-4, click Next screen, you can view
channel 5-8.
Here you can control PTZ direction, speed, zoom, focus, iris, preset, tour, scan, pattern
aux function, light and wiper, rotation and etc.
Speed is to control PTZ movement speed. The value ranges from 1 to 8.The speed 8 is
faster than speed 1. You can use the remote control to click the small keyboard to set.
You can click and of the zoom, focus and iris to zoom in/out, definition and
brightness.
The PTZ rotation supports 8 directions. If you are using direction buttons on the front
panel, there are only four directions: up/down/left/right.
30
Figure 3-20
In the middle of the eight direction arrows, there is a 3D intelligent positioning key. See
Figure 3-21. Please make sure your protocol supports this function and you need to use
mouse to control.
Click this key, system goes back to the single screen mode. Drag the mouse in the screen
to adjust section size. The dragged zone supports 4X to 16X speeds. It can realize PTZ
automatically. The smaller zone you dragged, the higher the speed.
Figure 3-21
In Figure 3-20, click to open the menu, you can set preset, tour, pattern, scan and
etc. See Figure 3-22.
Figure 3-22
31
Please note the above interface may vary due to different protocols. The button is grey
and can not be selected once the current function is null.
Right click mouse or click the ESC button at the front panel to go back to the Figure
3-20.
Icon Function Icon Function
Preset Flip
Tour Reset
Pattern Aux
Click , you can go to the following interface to set preset, tour, pattern, and scan. See
Figure 3-23.
Figure 3-23
Preset Setup
In Figure 3-23, click preset button and use eight direction arrows to adjust camera to the
proper position. The interface is shown as in Figure 3-24.
Click Set button and then input preset number.
Click Set button to save current preset.
32
Figure 3-24
Tour Setup
In Figure 3-23, click tour button.
Input tour value and preset No. Click Add preset button to add current preset to the tour.
See Figure 3-25.
Tips
Repeat the above steps to add more presets to the tour. Click Del preset button to remove
it from the tour. Please note some protocols do not support delete preset function.
Figure 3-25
Pattern Setup
In Figure 3-23, click Pattern button and input pattern number.
Click Begin button to start direction operation. Or you can go back to Figure 3-20 to
operate zoom/focus/iris/direction operation.
In Figure 3-23, click End button.
33
Figure 3-26
Scan Setup
In Figure 3-23, click Scan button.
Use direction buttons to set camera left limit and then click Left button.
Use direction buttons to set camera right limit and then click Right button. Now the scan
setup process is complete.
Figure 3-27
3.5.3.2 Call PTZ Function
Call Preset
In Figure 3-22, input preset value and then click to call a preset. Click
again to stop call.
Call Pattern
In Figure 3-22, input pattern value and then click to call a pattern. Click
again to stop call.
Call Tour
34
In Figure 3-22, input tour value and then click to call a tour. Click again
to stop call.
Call Scan
In Figure 3-22, input Scan value and then click to call a tour. Click again
to stop call.
Rotate
Aux
Click , system goes to the following interface. The options here are defined by the
protocol. The aux number is corresponding to the aux on-off button of the decoder. See
Figure 3-28.
Figure 3-28
3.5.4 Auto Focus
It is to set auto focus function. Please make sure the camera supports this function.
3.5.5 Color
Here you can set hue, brightness, contrast, saturation, gain, white level, color mode
and etc. See Figure 3-29.
35
Figure 3-29
Please refer to the following sheet for detailed information.
Item Note
Period There are two periods in one day. You can set different
sharpness, brightness, and contrast setup for different
periods.
Effective Time Check the box here to enable this function and then set
period time.
The value here is to adjust the edge of the video. The
value ranges from 0 to 100. The larger the value is, the
Sharpness clear the edge is and vice versa. Please note there is
noise if the value here is too high. The default value is 50
and the recommended value ranges from 40 to 60.
Brightness It is to adjust monitor window bright. The value ranges
from 0 to 100. The default value is 50.
The larger the number, the bright the video is. When you
input the value here, the bright section and the dark
section of the video will be adjusted accordingly. You
can use this function when the whole video is too dark or
too bright. Please note the video may become hazy if the
value is too high. The recommended value ranges from
40 to 60.
Contrast It is to adjust monitor window contrast. The value ranges
36
Item Note
from 0 to 100. The default value is 50.
The larger the number, the higher the contrast is. You
can use this function when the whole video bright is OK
but the contrast is not proper. Please note the video may
become hazy if the value is too low. If this value is too
high, the dark section may lack brightness while the
bright section may over exposure .The recommended
value ranges from 40 to 60.
Saturation It is to adjust monitor window saturation. The value
ranges from 0 to 100. The default value is 50.
The larger the number, the strong the color is. This value
has no effect on the general brightness of the whole
video. The video color may become too strong if the
value is too high. For the grey part of the video, the
distortion may occur if the white balance is not accurate.
Please note the video may not be attractive if the value
is too low. The recommended value ranges from 40 to
60.
Gain The gain adjust is to set the gain value. The default
value may vary due to different device models. The
smaller the value, the low the noise. But the brightness is
also too low in the dark environments. It can enhance
the video brightness if the value is high. But the video
noise may become too clear.
Color mode It includes several modes such as standard, color, bright,
gentle. Select a color mode, the sharpness, brightness,
contrast and etc can automatically switch to
corresponding setup.
EQ
Click or to adjust image equalization value.
(16:9). Icon means current display output mode. See Figure 3-30.
37
Figure 3-30
3.5.7 Face Search
It is to display human face record list, and view human face recognition record file.
3.5.8 Search
Please refer to chapter 3.9.1 for detailed information.
38
Figure 3-31
3.6.1 Main Menu
Click button to enable tour, the icon becomes , you can see the tour is in
process.
3.6.5 Favorites
Figure 3-32
3.6.6 Channel
It is to pop up channel tree. You can left click to select a channel on the tree and then drag
it to the preview window on the left pane.
3.6.7 PTZ
Click , system goes to the PTZ control interface. Please refer to chapter 3.5.3.
3.6.8 Color
Click button , system goes to the color interface. Please refer to chapter 3.5.5.
3.6.9 Search
Click button , system goes to search interface. Please refer to chapter 3.9.1
3.6.10 Alarm Status
39
Click button , system goes to alarm status interface. It is to view device status and
channel status. Please refer to chapter 3.11.3.
3.6.11 Channel Info
Click button , system goes to the channel information setup interface. It is to view
information of the corresponding channel. See Figure 3-33.
Figure 3-33
3.6.12 Remote Device
Click , system goes to an interface for you to view remote device information. Please
refer to chapter 3.11.1.1.
3.6.13 Network
Click , system goes to the network interface. It is to set network IP address, default
gateway and etc. Please refer to chapter 3.11.2.
Click , system goes to the HDD manager interface. It is to view and manage HDD
information. Please refer to chapter 3.11.4.2.
3.6.15 USB Manager
40
Click , system goes to the USB Manager interface. It is to view USB information,
backup and update. Please refer to chapter 3.9.3, chapter 3.10.4, chapter 3.11.5.10, and
chapter 3.11.5.12 for detailed information.
Figure 3-34
41
Figure 3-35
3.9 Operation
3.9.1 Search
Click search button in the main menu, search interface is shown as below. See Figure
3-36.
Usually there are four file types:
R: Regular recording file.
A: External alarm recording file.
M: Motion detection recording file
Orange: Intelligent recording file.
42
Figure 3-36
Please refer to the following sheet for more information.
SN Name Function
Display Here is to display the searched picture or file.
1
window Support 1/4/9/16-window playback.
Here you can select to search the picture or the recorded file.
You can select to play from the read-write HDD, from peripheral device or from
redundancy HDD.
Before you select to play from the peripheral device, please connect the
corresponding peripheral device. You can view all record files of the root directory
of the peripheral device. Click the Browse button; you can select the file you want to
Search
2 play.
type
Check the box here; you can enable splice playback function. Please refer to
chapter 3.9.1.4 for detailed information.
Important
Redundancy HDD does not support picture backup function, but it
supports picture playback function. You can select to play from redundancy
HDD if there are pictures on the redundancy HDD.
The blue highlighted date means there is picture or file. Otherwise, there is no
3 Calendar picture or file.
In any play mode, click the date you want to see, you can see the
43
corresponding record file trace in the time bar.
Playback mode:1/4/9/16/customized. (It may vary due to different series.)
In 1-window playback mode: you can select 1-16 channels.
In 4-window playback mode: you can select 4 channels according to your
Playback
requirement.
mode
In 9-window playback mode, you can switch between 1-8 and 9-16 channels.
and
4 In 16-window playback mode, you can switch between1-16 and 17-32
channel
channels.
selection
In customized mode, you can select one or more channel(s) you want to
pane.
playback at the same time. See chapter 3.9.1.4.
The time bar will change once you modify the playback mode or the channel
option.
The card number search interface is shown as below. Here you can view card
Card
number/field setup bar. You can implement advanced search.
5 number
search
Click it to go to mark file list interface. You can view all mark information of current
Mark file
6 channel by time. Please refer to chapter 3.9.1.3 for detailed information.
list button
Please note only the product of this icon supports mark function.
Double click it, you can view the picture/record file list of current day.
The file list is to display the first channel of the record file.
The system can display max 128 files in one time. Use the │and │ or the
mouse to view the file. Select one item, and then double click the mouse or click the
ENTER button to playback.
You can input the period in the following interface to begin accurate search.
File list File type:R—regular record; A—external alarm record;M—Motion detect
7 switch record.
button
Lock file. Click the file you want to lock and click the button to lock. The
file you locked will not be overwritten.
Search locked file: Click the button to view the locked file.
Play/Pause
There are three ways for you to begin playback.
The play button
►/
Playback Double click the valid period of the time bar.
8
control Double click the item in the file list.
pane. In slow play mode, click it to switch between play/pause.
■ Stop
Backward play
In normal play mode, left click the button, the file begins backward play.
44
Click it again to pause current play.
In backward play mode, click ►/ to restore normal play.
In playback mode, click it to play the next or the previous section. You can
click continuously when you are watching the files from the same channel.
│/
In normal play mode, when you pause current play, you can click │ and
│
│ to begin frame by frame playback.
In frame by frame playback mode, click ►/ to restore normal playback.
► Slow play
In playback mode, click it to realize various slow play modes such as slow
play 1, slow play 2, and etc.
Fast forward
In playback mode, click to realize various fast play modes such as fast
play 1,fast play 2 and etc.
Note: The actual play speed has relationship with the software version.
Smart search
Click the snapshot button in the full-screen mode, the system can snapshot
1 picture.
System supports custom snap picture saved path. Please connect the
peripheral device first, click snap button on the full-screen mode, you can
select or create path. Click Start button, the snapshot picture can be saved
to the specified path.
Mark button.
Please note this function is for some series product only. Please make sure
there is a mark button in the playback control pane.
You can refer to chapter 3.9.1.3 for detailed information.
It is to display the record type and its period in current search criteria.
In 4-window playback mode, there are corresponding four time bars. In other
playback mode, there is only one time bar.
Use the mouse to click one point of the color zone in the time bar, system
begins playback.
9 Time bar
The time bar is beginning with 0 o'clock when you are setting the configuration.
The time bar zooms in the period of the current playback time when you are playing
the file.
The green color stands for the regular record file. The red color stands for the
external alarm record file. The yellow stands for the motion detect record file.
●The option includes: 24H, 12H, 1H and 30M. The smaller the unit, the larger the
zoom rate. You can accurately set the time in the time bar to playback the record.
Time bar
10 The time bar is beginning with 0 o'clock when you are setting the configuration.
unit
The time bar zooms in the period of the current playback time when you are playing
the file.
45
Select the file(s) you want to backup from the file list. You can check from the
list. Then click the backup button, now you can see the backup menu. System
supports customized path setup. After select or create new folder, click the
Start button to begin the backup operation. The record file(s) will be saved in
the specified folder.
11 Backup
Check the file again you can cancel current selection. System max supports to
display 32 files from one channel.
After you clip on record file, click Backup button you can save it.
For one device, if there is a backup in process, you can not start a new backup
operation.
It is to edit the file.
●Please play the file you want to edit and then click this button when you want to
edit. You can see the corresponding slide bars in the time bar of the corresponding
channel. You can adjust the slide bar or input the accurate time to set the file end
time.
After you set, you can click Clip button again to edit the second period. You can
see the slide bar restore its previous position.
12 Clip
Click Backup button after clip, you can save current contents in a new file.
You can clip for one channel or multiple-channel. The multiple-channel click
operation is similar with the one-channel operation.
Please note:
System max supports 1024 files backup at the same time.
You can not operate clip operation if there is any file has been checked in
the file list.
Record
13 In any play mode, the time bar will change once you modify the search type.
type
Other Functions
When system is playing, you can select a zone in the window to begin smart
search. Click the motion detect button to begin play.
Once the motion detect play has begun, click button again will terminate
current motion detect file play.
Smart There is no motion detect zone by default.
14
search If you select to play other file in the file list, system switches to motion detect
play of other file.
During the motion detect play process, you can not implement operations such
as change time bar, begin backward playback or frame by frame playback.
Please refer to chapter 3.9.1.1 Smart Search for detailed operation.
Other
channel
synchroni When playing the file, click the number button, system can switch to the same
15
zation period of the corresponding channel to play.
switch to
play
46
when
playback
In pane 13 of Figure 3-36, click Sync button, you can playback the files of different
16 Sync
channels occurred at the same time.
Digital When the system is in full-screen playback mode, left click the mouse in the
17
zoom screen. Drag your mouse in the screen to select a section and then left click
mouse to realize digital zoom. You can right click mouse to exit.
Manually
switch During the file playback process, you can switch to other channel via the
18 channel dropdown list or rolling the mouse.
when This function is null if there is no record file or system is in smart search process.
playback
button, system begins smart search. System supports 396(22*18 PAL) and
330(22*15 NTSC) zones. Please left click mouse to select smart search zones. See
Figure 3-37.
Figure 3-37
Click the , you can go to the smart search playback. Click it again, system stops
smart search playback.
Important
System does not support motion detect zone setup during the full-screen
mode.
47
During the multiple-channel playback, system stops playback of rest channels
if you implement one-channel smart search.
the Figure 3-38 For example, input time 11:00.00 and then click Search button ,
you can view all the record files after 11:00.00 (The records includes current time.). See
image on the right side of the Figure 3-38 Double click a file name to playback.
Note
After you searched files, system implement accurate playback once you click Play
for the first time.
System does not support accurate playback for picture.
System supports synchronization playback and non-synchronous playback. The
synchronization playback supports all channels and non-synchronous playback
only supports accurately playback of current select channel.
Figure 3-38
48
Figure 3-39
Playback Mark
During 1-window playback mode, click mark file list button in Figure 3-36, you can go
to mark file list interface. Double click one mark file, you can begin playback from the mark
time.
Note
Usually, system can playbacks previous N seconds record if there is such kind of record
file. Otherwise, system playbacks from the previous X seconds when there is such as kind
of record.
Mark Manager
Click the mark manager button on the Search interface (Figure 3-36); you can go
to Mark Manager interface. See Figure 3-40. System can manage all the record mark
information of current channel by default. You can view all mark information of current
channel by time.
Figure 3-40
Modify
49
Double click one mark information item, you can see system pops up a dialogue box for
you to change mark information. You can only change mark name here.
Delete
Here you can check the mark information item you want to delete and then click Delete
button, you can remove one mark item. .
Note
After you go to the mark management interface, system needs to pause current
playback. System resume playback after you exit mark management interface.
If the mark file you want to playback has been removed, system begins playback from
the first file in the list.
In pane 4, click , you can see the following interface. See Figure 3-41.
Figure 3-41
Now you can select one or more channel(s) and then click to search record(s).
System supports one or more channels. The window split mode can auto adjust according
to the channel amount. System max supports 16-split.
On the main menu, click Search button, or right click mouse and then select Search. You can
go to the Figure 3-36.
50
On the right pane, check the box to enable splice playback function, and then set channel,
date, split mode. The splice playback interface is shown as below. Each section has a
small triangle; you can adjust it to set time. See Figure 3-42.
Figure 3-42
Note
Select split mode, so that the record can be spliced in several sections.
Note
The splice playback is for 1-window playback mode.
System supports 1/4/8/16-split mode. Slight different may be found here.
The min period of each section is 5 minutes. For the record is less than 20 minutes, if
you select 4-split mode (or more than 4-split mode), system can auto adjust so that
the each section period is 5 minutes. In this situation, some channel may have no
video.
51
Figure 3-43
Please refer to the following sheet for detailed information.
SN Name Function
1 Display It is to display human face detection file list. The latest file is at the
pan top. \
Click Export, you can export the selected file to the USB device.
There are two types: image/record.
Image: Export the recognized human face image.
Record: Export the record file before and after 10 seconds
when the DVR recognizes the human face.
2 Playback Play the searched record file or image. Double click to playback in full
pane screen.
3 Search Set date, start time and end time, click Search button, you can view the
pane corresponding file list.
3.9.3 Backup
DVR support CD-RW, DVD burner, USB device backup, network download and
eSATA. Here we introduce USB, eSATA backup. You can refer to Chapter 7 Web
Client Operation for network download backup operation.
Click backup button, you can see an interface is shown as in Figure 3-44. Here is for
you to view devices information.
52
You can view backup device name and its total space and free space. The device
includes CD-RW, DVD burner, USB device, flash disk, eSATA backup.
Figure 3-44
Select backup device and then set channel, file start time and end time.
Click add button, system begins search. All matched files are listed below. System
automatically calculates the capacity needed and remained. See Figure 3-45.
Figure 3-45
System only backup files with a √ before channel name. You can use Fn or cancel
53
button to delete √ after file serial number.
Click Start button, system begins copy. At the same time, the backup button becomes
stop button. You can view the remaining time and process bar at the left bottom. See
Figure 3-46.
Figure 3-46
When the system completes backup, you can see a dialogue box prompting
successful backup.
File format: Click the file format; you can see there are two options: DAV/ASF.
The file name format usually is: Channel number+Record type+Time. In the file name,
the YDM format is Y+M+D+H+M+S. File extension name is .dav.
Tips:
During backup process, you can click ESC to exit current interface for other operation.
The system will not terminate backup process.
Note:
When you click stop button during the burning process, the stop function becomes
activated immediately. For example, if there are ten files, when you click stop system
just backup five files, system only save the previous 5 files in the device (But you can
view ten file names).
54
Figure 3-47
3.10 Information
3.10.1 System Info
Here is for you to view system information. There are total four items: HDD (hard disk
information), record, BPS (data stream statistics), version. See Figure 3-48.
Figure 3-48
3.10.1.1 HDD Information
Here is to list hard disk type, total space, free space, video start time and status. See
Figure 3-49.
SATA: 1-2 here means system max supports 2 HDDS. ○ means current HDD is
55
normal. X means there is error. - means there is no HDD. If disk is damaged, system
shows as “?”. Please remove the broken hard disk before you add a new one.
SN: You can view the HDD amount the device connected to. ﹡ means the second
HDD is current working HDD.
Type: The corresponding HDD properties.
Total space: The HDD total capacity.
Free space: The HDD free capacity.
Status: HDD can work properly or not.
SMART: Display HDD information. See Figure 3-50.
Figure 3-49
Double click one HDD information; you can see the HDD SMART information. . See
Figure 3-50.
56
Figure 3-50
Figure 3-51
3.10.1.3 Record Estimate
System can calculate the record time based on the HDD space, or you can input the
record time you want to calculate the HDD space you need. See Figure 3-52.
57
Figure 3-52
Click after the channel name, system pops up Edit dialogue box. See Figure 3-53.
You can input resolution, frame rate, bit stream, record time of the corresponding channel,
system can calculate the record time based on the channel setup and HDD space.
Figure 3-53
58
Calculate the record period based on the HDD space
Check the channel you want to record file.
Click Known Space and then click the button to set HDD. Click OK button.
Now you can see the record period (such as 5 days). See Figure 3-54.
Figure 3-54
Calculate the HDD space based on the record period
Check the channel you want to record file.
Input days(s) you want to records, system can auto calculate the HDD space needed
(such as 5.109TB). See Figure 3-55.
59
Figure 3-55
3.10.1.4 BPS
Here is for you to view current video data stream (KB/s) and occupied hard disk storage
(MB/h). See Figure 3-56.
Figure 3-56
60
3.10.1.5 Device Status
It is to view device status information. See Figure 3-57. Please note this function is for
some series only.
Figure 3-57
3.10.1.6 Version
Here is for you to view some version information such as version number, built date, serial
number and etc. See Figure 3-58.
61
Figure 3-58
3.10.2 Event
It is to display device status and channel status. See Figure 3-59.
Figure 3-59
3.10.3 Network
3.10.3.1 Online Users
62
Here is for you to manage online users. See Figure 3-60.
You can disconnect one user or block one user if you have proper system right. Max
disconnection setup is 65535 seconds.
System detects there is any newly added or deleted user in each five seconds and refresh
the list automatically.
Figure 3-60
3.10.3.2 Network Load
Network load is shown as in Figure 3-61. Here you can view the follow statistics of the
device network adapter.
Here you can view information of all connected network adapters. The connection status
is shown as offline if connection is disconnected. Click one network adapter, you can view
the flow statistics such as send rate and receive rate at the top panel.
63
Figure 3-61
3.10.3.3 Network Test
Network test interface is shown as in Figure 3-62.
Destination IP: Please input valid IPV4 address or domain name.
Test: Click it to test the connection with the destination IP address. The test results
can display average delay and packet loss rate and you can also view the network
status as OK, bad, no connection and etc.
Network Sniffer backup: Please insert USB2.0 device and click the Refresh button,
you can view the device on the following column. You can use the dropdown list to
select peripheral device. Click Browse button to select the snap path. The steps here
are same as preview backup operation.
You can view all connected network adapter names (including Ethernet, PPPoE, WIFI,
and 3G), you can click the button on the right panel to begin Sniffer. Click the grey
stop button to stop. Please note system can not Sniffer several network adapters at the
same time.
After Sniffer began, you can exit to implement corresponding network operation such as
login WEB, monitor. Please go back to Sniffer interface to click stop Sniffer. System
can save the packets to the specified path. The file is named after “Network adapter
name+time”. You can use software such as Wireshark to open the packets on the PC for
the professional engineer to solve complicated problems.
64
Figure 3-62
3.10.4 Log
3.10.4.1 Local Log
Here is for you to view system log file. System lists the following information. See Figure
3-63.
Log types include system operation, configuration operation, data management, alarm
event, record operation, account manager, log clear, file operation and etc. It optimized
reboot log. There are only three types: normal reboot, abnormal reboot and protection
reboot. 0x02、0x03、0x04 is included in the protection reboot type.
Start time/end time: Pleased select start time and end time, then click search button.
You can view the log files in a list. System max displays 100 logs in one page. It can
max save 1024 log files. Please use page up/down button on the interface or the front
panel to view more.
Backup: Please select a folder you want to save; you can click the backup button to
save the log files. After the backup, you can see there is a folder named Log_time on
the backup path. Double click the folder, you can see the log file
Details: Click the Details button or double click the log item, you can view the detailed
information. See Figure 3-64. Here you can use rolling bar to view information, or you
can use Page up/Page down to view other log information.
65
Figure 3-63
Select an item on the list and then click the Details button or double click the log item, you
can view the detailed information such as log time, log type, log user, IP address and etc.
See Figure 3-64.
Figure 3-64
66
Note
If there is no HDD, system max supports 1024 logs.
If you have connected to the unformatted HDD, system max supports 5000 logs.
If you have connected to the formatted HDD, system max supports 500,000 logs.
System operation logs are saved in system memory. Other types of logs are saved in
the HDD. If there is no HDD, other types of logs are saved in the system memory too.
The logs are safe when you format the HDD. But the logs may become loss once you
removed the HDD.
3.11 Setting
3.11.1 Camera
3.11.1.1 Remote Device (For digital channel only)
3.11.1.1.1 Remote Device
In the main menu, from Camera ->Remote, you can go to an interface shown as in Figure
3-65. Here you can add/delete remote device and view its corresponding information.
IP search: Click it to search IP address. It includes device IP address, port, device
name, manufacturer, type. Use your mouse to click the item name, you can refresh
display order. Click IP address, system displays IP address from small to large. Click
IP address again, you can see icon, system displays IP address from large to small.
You can click other items to view information conveniently. For the network device
already added to the device, you can see there is a small icon “*” after the SN in case
there is repeatedly add operation.
Add: Click it to connect to the selected device and add it to the Added device list.
Support Batch add.
You can see the corresponding dialogue box if all digital-channel has connected to
the front-end.
System can not add new device if the device you want to add has the same IP and
TCP port as the device in the list.
Show filter: You can use it to display the specified devices from the added device.
Edit: Click button or double click a device in the list, you can change channel
setup.
Delete: Please select one device in the Added device list and then click to
remove.
67
Figure 3-65
Click the Manual Add button; you can go to the following interface. See Figure 3-66.
Channel number:The dropdown list here displays unconnected channel number. You can
go to Figure 3-65 to set remote channel connection.
Please note:
This series product supports the IPC from many popular manufactures such as Sony,
Hitachi, Axis, Samsung, Dynacolor, Arecont, Onvif and Dahua.
System default IP address is 192.168.0.0 if you do not input IP address. System will
not add current IP address.
You can not add two or more devices in the Manual Add interface (Figure 3-66). Click
OKbutton, system connects to the corresponding front-end device of current channel
on the interface.
Figure 3-66
68
Show filer: It is to filter the searched device.
None: it is to display all searched devices.
IPC: It is to display all cameras.
DVR: It is to display all storage devices such as NVR, DVR.
Change IP:
Click , you can change the information such as IP address, subnet mask, and
default gateway, user name, password of the checked device. See Figure 3-67.
Figure 3-67
You can check several devices at the same time and then click the edit
button .See Figure 3-3. Please check Batch modify button and then input
start IP, end IP and default gateway.
69
Figure 3-68
IP Export
System can export the Added device list to your local USB device.
Please insert the USB device and then click the Export button; you can see the following
interface. See Figure 3-69.
Figure 3-69
Select the directory and then click the OK button. System pops up a dialogue box to
remind you successfully exported. Please click OK button to exit.
70
Note
The exported file extension name is .CVS. The file information includes IP address, port,
remote channel number, manufacturer, user name and password.
IP Import
Click Import button, you can see the following interface. See Figure 3-70.
Figure 3-70
Select the import file and then click the OK button. System pops up a dialogue box to
remind you successfully exported. Please click OK button to exit.
Note:
If the imported IP has conflicted with current added device, system pops up a dialogue
box to remind you. You have two options:
OK: Click OK button, system uses the imported setup to overlay current one.
Cancel: Click Cancel button, system adds the new IP setup.
Important
You can edit the exported .CVS file. Do not change the file format; otherwise it
may result in import failure.
Does not support customized protocol import and export.
The import and export device shall have the same language format.
3.11.1.1.2 Channel Status
Here you can view the IPC status of the corresponding channel such as motion detect,
video loss, tampering, alarm and etc. See Figure 3-71.
71
Connection status: : Connection succeeded. : Connection failed.
Refresh: Click it to get latest front-end channel status.
Figure 3-71
3.11.1.1.3 Firmware
It is to view channel, IP address, manufacturer, type, system version, SN, video input,
audio input, and etc. See Figure 3-72.
Figure 3-72
72
3.11.1.2 Image
For analog channel, the camera interface is shown as in Figure 3-73. For digital
channel, the camera interface is shown as in Figure 3-74.
Channel: Select a channel from the dropdown list.
Cable type: It is to set the cable type of the corresponding analog channel. When the
setup here matches the actual cable you are using, you can get the best image effect.
The default setup is COAXIAL. Please note this function is for some series products
only.
COAXIAL: When the corresponding channel is using coaxial cable, please select
COAXIAL.
UTP: When the corresponding channel is using UTP cable, please select UTP.
Usually we recommend 10Ohm UTP cable.
Saturation: It is to adjust monitor window saturation. The value ranges from 0 to 100.
The default value is 50. The larger the number, the strong the color is. This value has
no effect on the general brightness of the whole video. The video color may become
too strong if the value is too high. For the grey part of the video, the distortion may
occur if the white balance is not accurate. Please note the video may not be attractive
if the value is too low. The recommended value ranges from 40 to 60.
Brightness: It is to adjust monitor window bright. The value ranges from 0 to 100. The
default value is 50. The larger the number is, the bright the video is. When you input
the value here, the bright section and the dark section of the video will be adjusted
accordingly. You can use this function when the whole video is too dark or too bright.
Please note the video may become hazy if the value is too high. The recommended
value ranges from 40 to 60.
Contrast: It is to adjust monitor window contrast. The value ranges from 0 to 100. The
default value is 50. The larger the number is, the higher the contrast is. You can use
this function when the whole video bright is OK but the contrast is not proper. Please
note the video may become hazy if the value is too low. If this value is too high, the
dark section may lack brightness while the bright section may over exposure .The
recommended value ranges from 40 to 60.
Sharpness: The value here is to adjust the edge of the video. The value ranges from 0
to 100. The larger the value is, the clear the edge is and vice versa. Please note there
is noise if the value here is too high. The default value is 50 and the recommended
value ranges from 40 to 60.
Mirror: It is to switch video up and bottom limit. This function is disabled by default.
Flip: It is to switch video left and right limit. This function is disabled by default.
BLC:It includes several options: BLC/WDR/HLC/OFF.
BLC: The device auto exposures according to the environments situation so that the
darkest area of the video is cleared
WDR: For the WDR scene, this function can lower the high bright section and
enhance the brightness of the low bright section. So that you can view these two
sections clearly at the same time. The value ranges from 1 to 100. When you switch
the camera from no-WDR mode to the WDR mode, system may lose several seconds
record video.
73
HLC: After you enabled HLC function, the device can lower the brightness of the
brightest section according to the HLC control level. It can reduce the area of the halo
and lower the brightness of the whole video.
OFF: It is to disable the BLC function. Please note this function is disabled by default.
Profile: It is to set the white balance mode. It has effect on the general hue of the
video. This function is on by default. You can select the different scene mode such as
auto, sunny, cloudy, home, office, night, disable and etc to adjust the video to the best
quality.
Auto: The auto white balance is on. System can auto compensate the color
temperature to make sure the vide color is proper.
Sunny: The threshold of the white balance is in the sunny mode.
Night: The threshold of the white balance is in the night mode.
Customized: You can set the gain of the red/blue channel. The value reneges from 0
to 100.
Day/night. It is to set device color and the B/W mode switch. The default setup is auto.
Color: Device outputs the color video.
Auto: Device auto select to output the color or the B/W video according to the device
feature (The general bright of the video or there is IR light or not.)
B/W: The device outputs the black and white video.
Sensor: It is to set when there is peripheral connected IR light.
Image enhancement: It is to enhance video quality. The larger the value is, the clearer
the video is. But the noise may become large too.
2D NR: It is to process the noise of the single image. The video may become soft after
process. The larger the value is, the better the effect is.
3D NR: it is to process the multiple-frame (at least two frames). It is to use the frame
information between the following two frames to reduce noise. The larger the value is,
the better the effect is.
74
Figure 3-73
Figure 3-74
75
3.11.1.3 Encode
It is to set video bit stream, picture bit stream, video overlay parameter and etc.
3.11.1.3.1 Video
Video setting includes the following items. See Figure 3-75.
Channel: Select the channel you want.
SVC: SVC is so called scaled video coding. Check the box to enable this function.
During the network transmission process, system discards unimportant frames when
the bandwidth is not sufficient or the decode capability is low. It is to guarantee video
quality and transmission fluency.
Type: Please select from the dropdown list. There are three options: regular/motion
detect/alarm. You can set the various encode parameters for different record types.
Compression: System supports H.264H, H.264, H.264B, and MJPEG.
H.264H: It is the High Profile compression algorithm. It has the high encode
compression rate. It can achieve high quality encode at low bit stream. Usually
we recommend this type.
H.264 is the general compression algorithm.
H.264B is the Baseline algorithm. Its compression rate is low. For the same video
quality, it has high bit stream requirements.
Smart codec: Select Start from the dropdown list to enable smart codec function. The
DVR can auto reduce the video bit stream of the non-important surveillance object to
save the storage space.
Resolution: For analog channel, system supports various resolutions, you can select
from the dropdown list. Please note the option may vary due to different series. For
digital channel, the resolution here refers to the capability of the network camera.
Frame rate: It ranges from 1f/s to 25f/s in NTSC mode and 1f/s to 30f/s in PAL mode.
Bit rate type: System supports two types: CBR and VBR. In VBR mode, you can set
video quality.
Quality: There are six levels ranging from 1 to 6. The sixth level has the highest image
quality.
Video/audio: You can enable or disable the video/audio.
Audio format: Please select from the dropdown list. There are three options:
G711a/G711u/PCM.
Audio source: Please select from the dropdown list. There are two options:
local/HDCVI. For local mode, the audio signal is from the Audio In port. For HDCVI
mode, the audio signal is from the coaxial cable of the camera.
76
Figure 3-75
3.11.1.3.2 Snapshot
Here you can set snapshot mode, picture size, quality and frequency. See Figure 3-76.
Snapshot mode: There are two modes: regular and trigger. If you set timing mode,
you need to set snapshot frequency. If you set trigger snapshot, you need to set
snapshot activation operation.
Image size: Here you can set snapshot picture size.
Image quality: Here you can set snapshot quality. The value ranges from 1 to 6.
Interval: It is for you to set timing (schedule) snapshot interval.
77
Figure 3-76
3.11.1.3.3 Overlay
Overlay interface is shown as in Figure 3-77.
Cover area: Here is for you to set cover area. You can drag you mouse to set proper
section size. In one channel video, system max supports 4 zones in one channel.
Preview/monitor: privacy mask has two types. Preview and Monitor. Preview means
the privacy mask zone can not be viewed by user when system is in preview status.
Monitor means the privacy mask zone can not be view by the user when system is in
monitor status.
Time display: You can select system displays time or not when you playback. Please
click set button and then drag the title to the corresponding position in the screen.
Channel display: You can select system displays channel number or not when you
playback. Please click set button and then drag the title to the corresponding position
in the screen.
Copy:After you complete the setup, you can click Copy button to copy current setup
to other channel(s). You can see an interface is shown as in Figure 3-78. You can see
current channel number is grey. Please check the number to select the channel or you
can check the box ALL. Please click the OK button in Figure 3-78 and Figure 3-77
respectively to complete the setup.
78
Figure 3-77
Figure 3-78
3.11.1.3.4 Channel Name
It is to modify channel name. It max supports 31-character. See Figure 3-79.
Please note for digital channel, you can only modify the channel name of the connected
network camera.
79
Figure 3-79
3.11.1.3.5 Channel Type
It is to set channel type.
For analog channel (CVBS signal or HDCVI HD signal), you can select coaxial cable
or UTP cable. Please check first and then save setup. There is no need to reboot.
You can switch analog channel type to digital channel type if you want to connect to
network camera. The IP channel shall start from the last channel. System needs to
reboot to activate current setup.
Note
If there is no connected channel, the channel type here just displays previous connection
record. System supports self-adaptive after camera connection.
The interface is shown as in Figure 3-80 (penta-brid series product) or Figure 3-81
(general series product).
80
Figure 3-80
Figure 3-81
81
standard definition (CVBS) and analog HD (CVI, AHD or Other). For penta-brid series
product, each channel supports all types of signal connection (analog signal/IP
signal). For analog signal connection, the default setup is AUTO, that is to say, no
matter what analog signal (CVBS, CVI, AHD or other analog HD signal) connected;
the penta-brid can automatically recognize the signal and display the proper image.
There is no need to set manually.
If the auto recognition error occurred, penta-brid series product supports manual
setup too. The manual setup featuring high recognition speed and usually there is no
error. For example, in Figure 3-82, you can set channel 1 to connect to CVI camera,
channel 2 to connect to AHD camera, channel 3 to connect to CVBS camera.
Figure 3-82
Important
Add/cancel IP CAM function is for some 4/8/16-channel series product only.
Add IP CAM: Click it; you can add corresponding X IP channels. Here X refers to the
product channel amount such as 4/8/16. System needs to restart to activate new
setup. See Figure 3-83 (penta-brid series product) or Figure 3-84 (general series
product).
82
Figure 3-83
Figure 3-84
For example, there is a 4-channel analog device, after the A/D switch, it can max supports
4 analog channels and 4 IP channels. Once it has become the 3+1 mode (3 analog
83
restore original status.
Figure 3-85
Figure 3-86
3.11.1.3.1 Upgrade
Important
84
Penta-brid series product does not support upgrade function via coaxial cable. That is
to say, you cannot use this interface to upgrade the connected CVI camera if you are
using penta-brid series product.
Figure 3-87
3.11.2 Network
3.11.2.1 TCP/IP
The single network adapter interface is shown as in Figure 3-88 and the dual network
adapters interface is shown as in Figure 3-89
Network Mode : Includes multiple access, fault tolerance, and load balancing
Multiple-address mode: eth0 and eth1 operate separately. You can use the
services such as HTTP, RTP service via etho0 or the eth1. Usually you need to
set one default card (default setup is etho) to request the auto network service
form the device-end such as DHCP, email, FTP and etc. In multiple-address
mode, system network status is shown as offline once one card is offline.
Network fault-tolerance: In this mode, device uses bond0 to communicate with
the external devices. You can focus on one host IP address. At the same time,
85
you need to set one master card. Usually there is only one running card (master
card).System can enable alternate card when the master card is malfunction. The
system is shown as offline once these two cards are both offline. Please note
these two cards shall be in the same LAN.
Load balance: In this mode, device uses bond0 to communicate with the external
device. The eth0 and eth1 are both working now and bearing the network load.
Their network load are general the same. The system is shown as offline once
these two cards are both offline. Please note these two cards shall be in the same
LAN.
Default Network Card: Please select eth0/eth1/bond0(optional) after enable
multiple-access function
Main Network Card: Please select eth0/eth1 (optional).after enable multiple
access function.
Note: Some series support the above three configurations and supports
functions as multiple-access, fault-tolerance and load balancing.
IP Version: There are two options: IPv4 and IPv6. Right now, system supports these two
IP address format and you can access via them.
MAC address: The host in the LAN can get a unique MAC address. It is for you to access
in the LAN. It is read-only.
IP address: Here you can use up/down button () or input the corresponding
number to input IP address. Then you can set the corresponding subnet mask the
default gateway.
Default gateway: Here you can input the default gateway. Please note system needs
to check the validity of all IPv6 addresses. The IP address and the default gateway
shall be in the same IP section. That is to say, the specified length of the subnet prefix
shall have the same string.
DHCP: It is to auto search IP. When enable DHCP function, you can not modify
IP/Subnet mask /Gateway. These values are from DHCP function. If you have not
enabled DHCP function, IP/Subnet mask/Gateway display as zero. You need to
disable DHCP function to view current IP information. Besides, when PPPoE is
operating, you can not modify IP/Subnet mask /Gateway.
MTU: It is to set MTU value of the network adapter. The value ranges from 1280-7200
bytes. The default setup is 1500 bytes. Please note MTU modification may result in
network adapter reboot and network becomes off. That is to say, MTU modification
can affect current network service. System may pop up dialog box for you to confirm
setup when you want to change MTU setup. Click OK button to confirm current reboot,
or you can click Cancel button to terminate current modification. Before the
modification, you can check the MTU of the gateway; the MTU of the DVR shall be the
same as or is lower than the MTU of the gateway. In this way, you can reduce packets
and enhance network transmission efficiency.
The following MTU value is for reference only.
1500: Ethernet information packet max value and it is also the default value. It is
the typical setup when there is no PPPoE or VPN. It is the default setup of some
router, switch or the network adapter.
86
1492: Recommend value for PPPoE.
1468: Recommend value for DHCP.
Preferred DNS server: DNS server IP address.
Alternate DNS server: DNS server alternate address.
Transfer mode: Here you can select the priority between fluency/video qualities.
LAN download: System can process the downloaded data first if you enable this
function. The download speed is 1.5X or 2.0X of the normal speed.
LAN download: System can process the downloaded data first if you enable this
function. The download speed is 1.5X or 2.0X of the normal speed.
After completing all the setups please click save button, system goes back to the previous
menu.
Figure 3-88
87
Figure 3-89
3.11.2.2 Connection
The connection setup interface is shown as in Figure 3-90.
Max connection: system support maximal 128 users. 0 means there is no connection
limit.
TCP port: Default value is 37777.
UDP port: Default value is 37778.
HTTP port: Default value is 80.
HTTPS port: Default value is 443.
RTSP port: Default value is 554.
Important: System needs to reboot after you changed and saved any setup of the
above four ports. Please make sure the port values here do not conflict.
88
Figure 3-90
3.11.2.3 WIFI
The WIFI interface is shown as below. See Figure 3-91.
Auto connect WIFI: Check the box here, system automatically connects to the
previous WIFI hotspot.
Refresh: You can click it to search the hotspot list again. It can automatically add the
information such as the password if you have set it before.
Disconnect: Here you can click it to turn off the connection.
Connect: Here you can click it to connect to the hotspot. System needs to turn off
current connection and then connect to a new hotspot if there is connection of you
selected one.
89
Figure 3-91
WIFI working status: Here you can view current connection status.
Please note:
After successful connection, you can see WIFI connection icon at the top right corner
of the preview interface.
When the hotspot verification type is WEP, system displays as AUTO since the device
can not detect its encryption type.
System does not support verification type WPA and WPA2. The display may become
abnormal for the verification type and encryption type.
After device successfully connected to the WIFI, you can view the hotspot name, IP
address, subnet mask, default gateway and etc.
3.11.2.4 3G
3G setup interface is shown as below. See Figure 3-92.
Please refer to the following contents for the parameter information.
Pane 1: Display 3G signal intensity after you enabled 3G function.
Pane 2: Display 3G module configuration information after you enabled 3G function.
Pane 3: Display 3G module status information after you enabled 3G function.
It is to display current wireless network signal intensity such as EVDO, CDMA1x, WCDMA,
WCDMA, EDGE and etc.
3G module: It is to display current wireless network adapter name.
3G Enable/Disable: Check the box here to enable 3G module.
Network type: There are various network types for different 3G network modules. You
can select according to your requirements.
90
APN: It is the wireless connection server. It is to set you access the wireless network
via which method.
AUTH: It is the authentication mode. It supports PAP/CHAP.
Dial number: Please input 3G network dialup number you got from your ISP.
User name: It is the user name for you to login the 3G network.
Password: It is the password for you to login the 3G network.
Pulse interval: You can set dialup duration. Once you disable the extra stream, the
connection time begins. For example, if you input 5 seconds here, then 3G network
connection period is 5 seconds. The device automatically disconnect when time is up.
If there is no extra stream, 3G network connection is valid all the time. If the alive
time is 0, then the 3G network connection is valid all the time.
Dial: Here you can enable or disable 3G network connection/disconnection manually.
3G wireless network: Here is to display wireless network status, SIM card status, dial
status. If the 3G connection is OK, then you can see the device IP address the
wireless network automatically allocates.
Figure 3-92
3.11.2.5 PPPoE
PPPoE interface is shown as in Figure 3-93.
Input “PPPoE name” and “PPPoE password” you get from your ISP (Internet service
provider).
Click save button, you need to restart to activate your configuration.
After rebooting, DVR will connect to internet automatically. The IP in the PPPoE is the
DVR dynamic value. You can access this IP to visit the unit.
91
Figure 3-93
3.11.2.6 DDNS Setup
DDNS setup interface is shown as in Figure 3-94.
You need a PC of fixed IP in the internet and there is the DDNS software running in this
PC. In other words, this PC is a DNS (domain name server).
In network DDNS, please select DDNS type and highlight enable item. Them please input
your PPPoE name you get from you IPS and server IP (PC with DDNS). Click save button
and then reboot system.
Click save button, system prompts for rebooting to get all setup activated.
After rebooting, open IE and input as below:
http://(DDNS server IP)/(virtual directory name)/webtest.htm
e.g.: http://10.6.2.85/DVR _DDNS/webtest.htm.)
Now you can open DDNSServer web search page.
92
Figure 3-94
Please note DDNS type includes: CN99 DDNS, NO-IP DDNS, Quick DDNS, Dyndns
DDNS and sysdns DDNS. All the DDNS can be valid at the same time, you can select as
you requirement.
Private DDNS function shall work with special DDNS server and special Professional
Surveillance Software (PSS).
Quick DDNS and Client-end Introduction
1) Background Introduction
Device IP is not fixed if you use ADSL to login the network. The DDNS function allows you
to access the DVR via the registered domain name. Besides the general DDNS ,the Quick
DDNS works with the device from the manufacturer so that it can add the extension
function.
2) Function Introduction
The quick DDNS client has the same function as other DDNS client end. It realizes the
bonding of the domain name and the IP address. Right now, current DDNS server is for
our own devices only. You need to refresh the bonding relationship of the domain and the
IP regularly. There is no user name, password or the ID registration on the server. At the
same time, each device has a default domain name (Generated by MAC address) for your
option. You can also use customized valid domain name (has not registered.).
3) Operation
Before you use Quick DDNS, you need to enable this service and set proper server
address, port value and domain name.
Server address:www.quickddns.com
Port number:80
93
Domain name:There are two modes: Default domain name and customized domain
name.
Except default domain name registration, you can also use customized domain name
(You can input your self-defined domain name.) After successful registration, you can
use domain name to login installed of the device IP.
User name: It is optional. You can input your commonly used email address.
Important
Do not register frequently. The interval between two registrations shall be more than
60 seconds. Too many registration requests may result in server attack.
System may take back the domain name that is idle for one year. You can get a
notification email before the cancel operation if your email address setup is OK.
3.11.2.7 IP Filter
IP filter interface is shown as in Figure 3-95. You can add IP in the following list. The list
supports max 64 IP addresses. System supports valid address of IPv4 and IPv6. Please
note system needs to check the validity of all IPv6 addresses and implement
optimization.
After you enabled trusted sites function, only the IP listed below can access current DVR.
If you enable blocked sites function, the following listed IP addresses can not access
current DVR.
Enable: Highlight the box here, you can check the trusted site function and blocked
sites function. You can not see these two modes if the Enable button is grey.
Type: You can select trusted site and blacklist from the dropdown list. You can view
the IP address on the following column.
Start address/end address: Select one type from the dropdown list, you can input IP
address in the start address and end address. Now you can click Add IP address or
Add IP section to add.
a) For the newly added IP address, it is in enable status by default. Remove the √
before the item, and then current item is not in the list.
b) System max supports 64 items.
c) Address column supports IPv4 or IPv6 format. If it is IPv6 address, system can
optimize it. For example, system can optimize aa:0000: 00: 00aa: 00aa: 00aa:
00aa: 00aa as aa:: aa: aa: aa: aa: aa: aa.
d) System automatically removes space if there is any space before or after the
newly added IP address.
e) System only checks start address if you add IP address. System check start
address and end address if you add IP section and the end address shall be
larger than the start address.
f) System may check newly added IP address exists or not. System does not add if
input IP address does not exist.
Delete: Click it to remove specified item.
Edit: Click it to edit start address and end address. See Figure 3-96. System can
check the IP address validity after the edit operation and implement IPv6 optimization.
94
Default: Click it to restore default setup. In this case, the trusted sites and blocked
sites are both null.
Note:
If you enabled trusted sites, only the IP in the trusted sites list can access the device.
If you enabled blocked sites, the IP in the blocked sites can not access the device.
System supports add MAC address.
Figure 3-95
Figure 3-96
3.11.2.8 Email
The email interface is shown as below. See Figure 3-97.
SMTP server: Please input your email SMTP server IP here.
Port: Please input corresponding port value here.
User name: Please input the user name to login the sender email box.
Password: Please input the corresponding password here.
Sender: Please input sender email box here.
95
Title: Please input email subject here. System support English character and Arabic
number. Max 32-digit.
Receiver: Please input receiver email address here. System max supports 3 email
boxes. System automatically filters same addresses if you input one receiver
repeatedly.
SSL enable: System supports SSL encryption box.
Interval: The send interval ranges from 0 to 3600 seconds. 0 means there is no
interval.
Health email enable: Please check the box here to enable this function. This function
allows the system to send out the test email to check the connection is OK or not.
Interval: Please check the above box to enable this function and then set the
corresponding interval. System can send out the email regularly as you set here.
Click the Test button, you can see the corresponding dialogue box to see the email
connection is OK or not.
Please note system will not send out the email immediately when the alarm occurs. When
the alarm, motion detection or the abnormity event activates the email, system sends out
the email according to the interval you specified here. This function is very useful when
there are too many emails activated by the abnormity events, which may result in heavy
load for the email server.
Figure 3-97
3.11.2.9 FTP
You need to download or buy FTP service tool (such as Ser-U FTP SERVER) to establish
FTP service.
96
Please install Ser-U FTP SERVER first. From “start” -> “program” -> Serv-U FTP Server
-> Serv-U Administrator. Now you can set user password and FTP folder. Please note you
need to grant write right to FTP upload user. See Figure 3-98.
Figure 3-98
You can use a PC or FTP login tool to test setup is right or not.
For example, you can login user ZHY to FTP://10.10.7.7
H1 40H140H140HTU UTHand then test it can modify
or delete folder or not. See Figure 3-99.
Figure 3-99
System also supports upload multiple DVRs to one FTP server. You can create multiple
folders under this FTP.
FTP interface is shown as in Figure 3-100.
97
uploads all corresponding files.
After completed channel and weekday setup, you can set two periods for one each
channel.
Click the Test button, you can see the corresponding dialogue box to see the FTP
connection is OK or not.
Figure 3-100
3.11.2.10 UPnP
The UPNP protocol is to establish a mapping relationship between the LAN and the WAN.
Please input the router IP address in the LAN in Figure 3-88. See Figure 3-101.
UPNP on/off :Turn on or off the UPNP function of the device.
Status: When the UPNP is offline, it shows as “Unknown”. When the UPNP works it
shows “Success”
Router LAN IP: It is the router IP in the LAN.
WAN IP: It is the router IP in the WAN.
Port Mapping list: The port mapping list here is the one to one relationship with the
router’s port mapping setting.
List:
Service name:Defined by user.
Protocol: Protocol type
Internal port:Port that has been mapped in the router.
External port:Port that has been mapped locally.
Default: UPNP default port setting is the HTTP, TCP and UDP of the DVR.
98
Add to the list: Click it to add the mapping relationship.
Delete: Click it to remove one mapping item.
Double click one item; you can change the corresponding mapping information. See
Figure 3-102.
Important:
When you are setting the router external port, please use 1024~5000 port. Do not
use well-known port 1~255 and the system port 256~1023 to avoid conflict.
For the TCP and UDP, please make sure the internal port and external port are the
same to guarantee the proper data transmission.
Figure 3-101
Figure 3-102
3.11.2.11 SNMP
99
SNMP is an abbreviation of Simple Network Management Protocol. It provides the basic
network management frame of the network management system. The SNMP widely used
in many environments. It is used in many network device, software and system.
You can set in the following interface. See Figure 3-103.
Figure 3-103
Please enable the SNMP function. Use the corresponding software tool (MIB Builder and
MG-SOFT MIB Browser. You still need two MIB file: BASE-SNMP-MIB, DVR-SNMP-MIB)
to connect to the device. You can get the device corresponding configuration information
after successfully connection.
Please follow the steps listed below to configure.
In Figure 3-103, check the box to enable the SNMP function. Input the IP address of
the PC than is running the software in the Trap address. You can use default setup for
the rest items.
Compile the above mentioned two MIB file via the software MIB Builder.
Run MG-SOFT MIB Browser to load the file from the previous step to the software.
Input the device IP you want to manage in the MG-SOFT MIB Browser. Please set
the corresponding version for your future reference.
Open the tree list on the MG-SOFT MIB Browser; you can get the device
configuration. Here you can see the device has how many video channels, audio
channels, application version and etc.
Note
Port conflict occurs when SNMP port and Trap port are the same.
3.11.2.12 Multicast
100
Multicast setup interface is shown as in Figure 3-104.
Figure 3-104
Here you can set a multiple cast group. Please refer to the following sheet for detailed
information.
IP multiple cast group address
-224.0.0.0-239.255.255.255
-“D” address space
The higher four-bit of the first byte=”1110”
Reserved local multiple cast group address
-224.0.0.0-224.0.0.255
-TTL=1 When sending out telegraph
-For example
224.0.0.1 All systems in the sub-net
224.0.0.2 All routers in the sub-net
224.0.0.4 DVMRP router
224.0.0.5 OSPF router
224.0.0.13 PIMv2 router
Administrative scoped addressees
-239.0.0.0-239.255.255.255
-Private address space
Like the single broadcast address of RFC1918
Can not be used in Internet transmission
Used for multiple cast broadcast in limited space.
Except the above mentioned addresses of special meaning, you can use other addresses.
101
For example:
Multiple cast IP: 235.8.8.36
Multiple cast PORT: 3666.
After you logged in the Web, the Web can automatically get multiple cast address and add
it to the multiple cast groups. You can enable real-time monitor function to view the view.
Please note multiple cast function applies to special series only.
Figure 3-105
2) The proxy server software developed from the SDK. Please open the software and
input the global setup. Please make sure the auto connection port here is the same as the
port you set in the previous step.
3) Now you can add device. Please do not input default port number such as the TCP port
in the mapping port number. The device ID here shall be the same with the ID you input in
102
Figure 3-105. Click Add button to complete the setup.
4) Now you can boot up the proxy server. When you see the network status is Y, it means
your registration is OK. You can view the proxy server when the device is online.
Important
The server IP address can also be domain. But you need to register a domain name
before you run proxy device server.
Figure 3-106
3.11.2.15 P2P
You can use your cell phone to scan the QR code and add it to the cell phone client.
Via the SN from scanning the QR code, you can access the device in the WAN. Please
refer to the P2P operation manual included in the resources CD.
From main menu->Setting->Network->P2P, you can go to the following interface, the P2P
interface is shown as in Figure 3-107.
103
Figure 3-107
Android:
Open Google Play app in your smart phone. Search gDMSS Lite or gDMSS Plus,
download it and install.
iOS:
Open App Store app in your smart phone. Search iDMSS Lite or iDMSS Plus, download it
and install.
Tap at the top left corner, you can see the main menu.
Tap Device manager button, you can use several modes (P2P/DDNS/IP and etc) to
add the device. Click to save current setup. Tap Start Live preview to view
all-channel video from the connected device. See Figure 3-108.
104
Figure 3-108
3.11.3 Event
3.11.3.1 Detect
In the main menu, from Setting->Event->Detect, you can see motion detect interface.
See Figure 3-109.There is three detection types: motion detection, video loss,
tampering.
The video loss has no detection region and sensitivity setup and tampering has no
detection region setup.
You can see motion detect icon if current channel has enabled motion detect
alarm.
You can drag you mouse to set motion detect region. Please click OK button to
save current region setup. Right click mouse to exit current interface.
For digital channel, the detect function refers to support detection function of the
front-end and support local activation function. The front-end can get
enable/disable status, sensitivity and region setup. You can get corresponding
prompt if front-end can not get the above information. You can change front-end
setup if it can get.
105
Region: Click select button, the interface is shown as in Figure 3-110. Here you can
set motion detection zone. There are four zones for you to set. Please select a zone
first and then left drag the mouse to select a zone. The corresponding color zone
displays different detection zone. You can click Fn button to switch between the arm
mode and disarm mode. In arm mode, you can click the direction buttons to move the
green rectangle to set the motion detection zone. After you completed the setup,
please click ENTER button to exit current setup. Do remember click save button to
save current setup. If you click ESC button to exit the region setup interface system
will not save your zone setup.
Sensitivity: System supports 6 levels. The sixth level has the highest sensitivity.
Anti-dither: Here you can set anti-dither time. The value ranges from 5 to 600s. The
anti-dither time refers to the alarm signal lasts time. It can be seem as the alarm
signal activation stays such as the buzzer, tour, PTZ activation, snapshot, channel
record. The stay time here does not include the latch time. During the alarm process,
the alarm signal can begin an anti-dither time if system detects the local alarm again.
The screen prompt, alarm upload, email and etc will not be activated. For example, if
you set the anti-dither time as 10 second, you can see the each activation may last
10s if the local alarm is activated. During the process, if system detects another local
alarm signal at the fifth second, the buzzer, tour, PTZ activation, snapshot, record
channel will begin another 10s while the screen prompt, alarm upload, email will not
be activated again. After 10s, if system detects another alarm signal, it can generate
an alarm since the anti-dither time is out.
Period: Click set button, you can see an interface is shown as in Figure 3-112. Here
you can set motion detect period. System only enables motion detect operation in the
specified periods. It is not for video loss or the tampering. There are two ways for you
to set periods. Please note system only supports 6 periods in one day.
In Figure 3-112, Select icon of several dates, all checked items can be edited
together. Now the icon is shown as . Click to delete a record type from one
period.
In Figure 3-112. Click button after one date or a holiday, you can see an
interface shown as in Figure 3-113. There are four record types: regular, motion
detection (MD), Alarm, MD & alarm.
Alarm output: when an alarm occurs, system enables peripheral alarm devices.
Latch: when motion detection complete, system auto delays detecting for a specified
time. The value ranges from 1-300(Unit: second)
Show message: System can pop up a message to alarm you in the local host screen if
you enabled this function.
Alarm upload: System can upload the alarm signal to the network (including alarm
center) if you enabled current function.
Send email: System can send out email to alert you when an alarm occurs.
106
Record channel: System auto activates motion detection channel(s) to record once an
alarm occurs. Please make sure you have set MD record in Schedule interface(Main
Menu->Setting->Schedule) and schedule record in manual record interface(Main
Menu->Advanced->Manual Record)
PTZ activation: Here you can set PTZ movement when an alarm occurs. Such as go
to preset, tour &pattern when there is an alarm. Click “select” button, you can see an
interface is shown as in Figure 3-111 .
X
Record Delay: System can delay the record for specified time after alarm ended. The
value ranges from 10s to 300s.
Tour: Here you can enable tour function when an alarm occurs. System one-window
tour.
Snapshot: You can enable this function to snapshot image when a motion detect
alarm occurs.
Video matrix Check the box here to enable this function. When an alarm occurs,
SPOT OUT port displays device video output. It displays video (1-window tour) from
alarm activation channel you select at the Record channel item.
Buzzer: Highlight the icon to enable this function. The buzzer beeps when an alarm
occurs.
Log: Check the box here, system can record motion detect log.
Test: Click it to test current motion detect setup (do not need to save). Click Select
button after Region, you can set motion detect area.
Voice prompts: Check the box here to trigger audio broadcast function. You can
select specified audio file here. System can play the audio file once the corresponding
event occurs.
Please highlight icon to select the corresponding function. After all the setups please
click save button, system goes back to the previous menu.
Note:
In motion detection mode, you can not use copy/paste to set channel setup since the
video in each channel may not be the same.
In Figure 3-110, you can left click mouse and then drag it to set a region for motion
detection. Click Fn to switch between arm/withdraw motion detection. After setting, click
enter button to exit.
107
Figure 3-109
Figure 3-110
108
Figure 3-111
Figure 3-112
109
Figure 3-113
Motion detect here only has relationship with the sensitivity and region setup. It has no
relationship with other setups.
110
Figure 3-114
3.11.3.1.3 Tampering
When someone viciously masks the lens, or the output video is in one-color due to the
environments light change, the system can alert you to guarantee video continuity.
Tampering interface is shown as in Figure 3-115. You can enable “Alarm output “or
“Show message” function when tampering alarm occurs.
Sensitivity: The value ranges from 1 to 6. It mainly concerns the brightness. The
level 6 has the higher sensitivity than level 1. The default setup is 3.
Tips:
You can enable preset/tour/pattern activation operation when video loss occurs.
Please refer to chapter 3.11.3.1.1 motion detection for detailed information.
Note:
In Detect interface, copy/paste function is only valid for the same type, which
means you can not copy a channel setup in video loss mode to tampering mode.
About Default function. Since detection channel and detection type may not be the
same, system can only restore default setup of current detect type. For example, if
you click Default button at the tampering interface, you can only restore default
tampering setup. It is null for other detect types.
System only enables tampering function during the period you set here. It is null
for motion detect or video loss type.
111
Figure 3-115
3.11.3.1.4 Diagnosis
Note
This function is for some series only.
System can trigger an alarm when the stripe, noise, color cast, out of focus, over
exposure event occurred. See Figure 3-116.
Please refer to chapter 3.11.3.1.1 motion detection for detailed information.
112
Figure 3-116
This function allows you to be informed when video is blurry, over exposure or color
cast occurs. You can enable alarm output channel and then enable show message
function. Click the Rule Set button, or move the cursor to Set button and then click the
Enter button on the front panel, the interface is shown as below. See Figure 3-117.
You can check corresponding type and then input alarm threshold.
Stripe: The strip occurs when the device is old or there is electronic interference.
There may be cross strip, vertical strip, slanting strip and etc.
Noise: The video noise refers to the blurry video, poor video quality. It may result from
the optical system distortion or the hardware problem during the video transmission
when recording.
Color cast: Usually the video is color containing RGB. When these three colors
displayed in abnormal rate, we can say color cast occurred.
Out of focus: The clear video presents abundant video details. The video definition
decreases when the distortion event occurs. The out of focus event may result from
many sources such as video transmission, processing and etc.
Over exposure: The color brightness refers to the image pixel intensity. Black is the
darkest and the white is the brightest. We use number 0 to stand for black and use
number 255 to stand for white. Once the brightness threshold of the whole image has
exceeded the threshold value, it means the image is over exposure.
Threshold: The value ranges from 1 to 30. System can generate an alarm once the
value is higher than the threshold you set here.
113
Figure 3-117
Note
Video analysis alarm can trigger PTZ preset, tour, and pattern.
Please refer to chapter 3.11.3.1.1 motion detection for detailed information.
Important
The intelligence function is optional.
The different series products support different IVS functions. Please refer to
your purchased product actual interface for detailed information.
The IVS function supports 1 analog channel only. Right now some series
products support IP channel.
Once any object violate the rule, the DVR can trigger an alarm and alert you as the
specified alarm mode.
From main menu->Setting->Event->Intelligence, you can go to the following interface.
Here you can set IVS rule. System can generate an alarm as the mode you
previously set once there is any object violates the rule. See Figure 3-118.
114
Figure 3-118
Select a channel from the dropdown list.
Click Add button to add a rule and then select a rule type from the dropdown list.
Click to draw the rule. For detailed information, please refer to chapter
3.11.3.2.1 Tripwire, 3.11.3.2.2 Intrusion, chapter 3.11.3.2.3 Abandoned.
115
Figure 3-119
Check the Enable box to enable tripwire function.
Click Rule setup to draw the tripwire. See Figure 3-120.
Figure 3-120
Select SN (Line1/2/3/4) and direction, and then input customized rule name.
116
Line1/2/3/4: System supports four tripwires. Each SN stands for one tripwire.
Now you can draw a rule. Left click mouse to draw a tripwire. The tripwire can be a direct
line, curve or polygon. Right click mouse to complete.
Figure 3-121
Select the blue line and then use mouse to adjust zone size.
Note
Each rule can set two sizes (min size/max size). Once the object is smaller than the min
size or larger than the max size, there is no alarm. Please make sure the max size is
larger than the min size.
Click Ok to complete the rule setup.
Tips
117
In Figure 3-112, Select icon of several dates, all checked items can be edited
together. Now the icon is shown as . Click to delete a record type from one
period.
In Figure 3-112. Click button after one date or a holiday, you can see an
interface shown as in Figure 3-113.
Alarm output: when an alarm occurs, system enables peripheral alarm devices.
Latch: when tripwire complete, system auto delays detecting for a specified time. The
value ranges from 0-300(Unit: second). The default setup is 10 seconds. The o
second means there is no delaying time.
Show message: System can pop up a message to alarm you in the local host
screen if you enabled this function.
Alarm upload: System can upload the alarm signal to the network (including alarm
center) if you enabled current function.
Send email: System can send out email to alert you when an alarm occurs.
Record channel: System auto activates tripwire channel(s) to record once an
alarm occurs. Please make sure you have set intelligent record in Schedule
interface(Main Menu->Setting->Schedule) and schedule record in manual record
interface(Main Menu->Advanced->Manual Record)
PTZ activation: Here you can set PTZ movement when an alarm occurs. Such as
go to preset, tour &pattern when there is an alarm. Click “select” button, you can
see an interface is shown as in Figure 3-111.
Record Delay: System can delay the record for specified time after alarm ended.
The value ranges from 10s to 300s.
Tour: Here you can enable tour function when an alarm occurs. System
one-window tour.
Snapshot: You can enable this function to snapshot image when a motion detect
alarm occurs.
Buzzer: Highlight the icon to enable this function. The buzzer beeps when an
alarm occurs.
Figure 3-122
118
Figure 3-123
Figure 3-124
119
Figure 3-125
Check the enable box to enable intrusion function.
Click Rule setup to draw the zone. See Figure 3-126.
Figure 3-126
Select SN (Area1/2/3/4) and direction, and then input customized rule name.
Area1/2/3/4: System supports four zones. Each SN stands for one zone.
120
Tips
System generates an alarm when the object missing/abandoned object alarm occurs.
From main menu->Setting->Event-> Intelligence ->Object, the object protection interface
is shown as below. See Figure 3-127.
Figure 3-127
Check the enable box to enable object detect function.
Click Rule setup to draw the rule.
121
Figure 3-128
Select SN (object1/2/3/4) and direction, and then input customized rule name.
Object1/2/3/4: System supports four zones. Each SN stands for one zone.
object left in the one for the specified time. For icon , system can generate an
alarm once the object is out of the zone for the specified time.
Period: It refers to the object in/out the zone time.
Now you can draw a rule. Left click mouse to draw a line, until you draw a rectangle, you
can right click mouse.
Click Ok to complete the rule setup.
Tips
122
Figure 3-129
Figure 3-130
Name: Input customized rule name.
123
Period: System can generate an alarm once the object is in the zone for the specified
period.
Target filter: Click , you can set filter object size. Each rule can set two sizes (min
size/max size). Once the object is smaller than the min size or larger than the max
size, there is no alarm. Please make sure the max size is larger than the min size.
Now you can draw a rule. Left click mouse to draw a zone, until you draw a rectangle, you
can right click mouse.
Tips
Click , you can refer to the chapter 3.11.3.2.1 to set other parameters.
Click Apply to complete the setup.
Figure 3-131
124
Figure 3-132
Name: Input customized rule name.
Period: System can generate an alarm once the object in the zone is missing for the
specified period.
Target filter: Click , you can set filter object size. Each rule can set two sizes (min
size/max size). Once the object is smaller than the min size or larger than the max
size, there is no alarm. Please make sure the max size is larger than the min size.
Now you can draw a rule. Left click mouse to draw a zone, until you draw a rectangle, you
can right click mouse.
Tips
Click , you can refer to the chapter 3.11.3.2.1 to set other parameters.
Click Apply to complete the setup.
The face detection function is optional. The intelligence function and the
human face detection can not be valid at the same time!
125
Note
The face detection function is valid once your network camera or your DVR supports
this function.
If your purchased DVR supports the face detection function, it supports one analog
channel. It is not for the digital channel.
System can detect and filter the human face via analyzing the video. When it detects
the human face in the specified zone, it can draw the rectangle around the human face
and trigger record, snapshot, alarm operation and etc. See Figure 3-133.
Channel: Select a channel you want to enable face detect function.
Alarm face number: Once the detected human face number reaches the threshold you
set here, system can generate an alarm.
Human face RO (region of interest): Check the box, system can highlight the human
face region.
Enable: Check the box here to enable face detect function.
For detailed setup information, please refer to chapter 3.11.3.2.
Figure 3-133
3.11.3.4 Alarm
Important
126
Penta-brid series product does not support HDCVI alarm function (Figure 3-136).
Before operation, please make sure you have properly connected alarm devices such
as buzzer.
In the main menu, from Setting->Event->Alarm, you can see alarm setup interface.
For analog channel, the interface is shown as in Figure 3-134 and Figure 3-135
For HDCVI channel, there are three alarm types. See Figure 3-134 to Figure 3-136.
For digital channel, there are four alarm types. See Figure 3-134 to Figure 3-138.
Local alarm: The alarm signal system detects from the alarm input port.
Network alarm: It is the alarm signal from the network.
HDCVI: System can get the camera temperature, smoke, external alarm and set
corresponding alarm activation operation.
IPC external alarm: It is the on-off alarm signal from the front-end device and can
activate the local HDVR.
IPC offline alarm: Once you select this item, system can generate an alarm when the
front-end IPC disconnects with the local HDVR. The alarm can activate record, PTZ,
snap and etc. The alarm can last until the IPC and the HDVR connection resumes.
Important
If it is your first time to boot up the device, the disconnection status of
the front-end network camera will not be regarded as offline. After one
successfully connection, all the disconnection events will be regarded
as IPC offline event.
When IPC offline alarm occurs, the record and snapshot function of
digital channel is null.
Alarm in: Here is for you to select channel number.
Type: normal open or normal close.
PTZ activation: Here you can set PTZ movement when an alarm occurs. Such as go
to preset, tour& pattern when there is an alarm. Click “select” button, you can see an
interface is shown as in Figure 3-139.
Period: Click set button, you can see an interface is shown as in Figure 3-140. There
are two ways for you to set periods. There are max 6 periods in one day. There are
four record types: regular, motion detection (MD), Alarm, MD & alarm.
In Figure 3-140, Select icon of several dates, all checked items can be
In Figure 3-140. Click button after one date or a holiday, you can see an
interface shown as in Figure 3-141. There are four record types: regular, motion
detection (MD), Alarm, MD & alarm.
Anti-dither: Here you can set anti-dither time. Here you can set anti-dither time. The
value ranges from 5 to 600s. The anti-dither time refers to the alarm signal lasts time.
It can be seem as the alarm signal activation stays such as the buzzer, tour, PTZ
127
activation, snapshot, channel record. The stay time here does not include the latch
time. During the alarm process, the alarm signal can begin an anti-dither time if
system detects the local alarm again. The screen prompt, alarm upload, email and etc
will not be activated. For example, if you set the anti-dither time as 10 second, you
can see the each activation may last 10s if the local alarm is activated. During the
process, if system detects another local alarm signal at the fifth second, the buzzer,
tour, PTZ activation, snapshot, record channel will begin another 10s while the
screen prompt, alarm upload, email will not be activated again. After 10s, if system
detects another alarm signal, it can generate an alarm since the anti-dither time is out.
Show message: System can pop up a message to alarm you in the local host screen if
you enabled this function.
Alarm upload: System can upload the alarm signal to the network (including alarm
center) if you enabled current function.
Send email: System can send out email to alert you when an alarm occurs.
Record channel: you can select proper channel to record alarm video (Multiple
choices). At the same time you need to set alarm record in schedule interface (Main
Menu->Setting->Schedule) and select schedule record in manual record interface
(Main Menu->Advance->Manual Record).
Latch: Here is for you to set proper delay duration. Value ranges from 10 to 300
seconds. System automatically delays specified seconds in turning off alarm and
activated output after external alarm cancelled.
Tour: Here you can enable tour function when an alarm occurs. System supports
1/8-window tour. Please note the tour setup here has higher priority than the tour
setup you set in the Display interface. Once there two tours are both enabled, system
can enable the alarm tour as you set here when an alarm occurred. If there is no
alarm, system implements the tour setup in the Display interface.
Snapshot: System can snapshot corresponding channel when an alarm occurs.
Please note the activation snapshot has the higher priority than schedule snapshot. If
you have enabled these two types at the same time, system can activate the
activation snapshot when an alarm occurs, and otherwise system just operates the
schedule snapshot.
Video matrix Check the box here to enable this function. When an alarm occurs,
SPOT OUT port displays device video output. It displays video (1-window tour) from
alarm activation channel you select at the Record channel item.
Log: Check the box here, system can record local alarm log.
Buzzer: Highlight the icon to enable this function. The buzzer beeps when an alarm
occurs.
Voice prompts: Check the box here to trigger audio broadcast function. You can
select specified audio file here. System can play the audio file once the corresponding
event occurs.
Please note, network alarm means the alarm signal from the TCP/IP. You can use
NET SDK to activate network alarm. Comparing with the local alarm, there is no type,
anti-dither, alarm upload function.
128
Please highlight icon to select the corresponding function. After setting all the
setups please click save button, system goes back to the previous menu.
Figure 3-134
Figure 3-135
129
Figure 3-136
.
Figure 3-137
130
Figure 3-138
Figure 3-139
131
Figure 3-140
Figure 3-141
3.11.3.5 Abnormality
There are four types: HDD/Network/User/Device. Please note device interface is for
some series only.
HDD: HDD error, no disk, no space. See Figure 3-142 and Figure 3-143.
Network: Disconnection, IP conflict, MAC conflict. See Figure 3-144.
User:Illegal login. See Figure 3-145 .
Device: High temperature, fan speed abnormal. See Figure 3-146.
Alarm output: Please select alarm activation output port (multiple choices).
132
Less than: System can alarm you when the HDD space is less than the threshold
you set here (For HDD no space type only).
Latch: Here you can set corresponding delaying time. The value ranges from 0s-300s.
System automatically delays specified seconds in turning off alarm and activated
output after external alarm cancelled. When the value is 0, there is no latch time.
High temperature: In Device interface (Figure 3-146), select High temperature from
the dropdown list, and then input the max temperature. The value ranges from 30℃~
90℃. Device can trigger an alarm once the case temperature is higher than the value
you set.
Fan speed abnormal: In Device interface (Figure 3-146), select Fan speed abnormal
from the dropdown list, and then click the OK button after the Fan calibration. It can
correct fan manually. Please note we recommend this function after you replaced or
maintained the fan.
Show message: system can pop up the message in the local screen to alert you
when an alarm occurs.
Alarm upload: System can upload the alarm signal to the network (including alarm
center) if you enabled current function. For disconnection event, IP conflict event
and MAC conflict event, this function is null.
Send email: System can send out email to alert you when an alarm occurs.
Buzzer: Highlight the icon to enable this function. The buzzer beeps when an alarm
occurs.
Log: Check the box here, system can record HDD event log.
Voice prompts: Check the box here to trigger audio broadcast function. You can
select specified audio file here. System can play the audio file once the corresponding
event occurs.
133
Figure 3-142
Figure 3-143
134
Figure 3-144
Figure 3-145
135
Figure 3-146
Figure 3-147
136
3.11.4 Storage
3.11.4.1 Schedule
3.11.4.1.1 Record
Note:
You need to have proper rights to implement the following operations. Please make
sure the HDDs have been properly installed.
After the system booted up, it is in default 24-hour regular mode. You can set record type
and time in schedule interface.
: Sync connection icon. Select icon of several dates, all checked items
Period setup: Click button after one date or a holiday, you can see an interface
shown as in Figure 3-152.There are four record types: regular, motion detection (MD),
Alarm, MD & alarm.
Please following the steps listed below to draw the period manually.
Select a channel you want to set. See Figure 3-148.
Figure 3-148
Set record type. See Figure 3-149.
137
Figure 3-149
Please draw manually to set record period. There are six periods in one day. See
Figure 3-150.
Figure 3-150
Please highlight icon to select the corresponding function. After completing all the
setups please click save button, system goes back to the previous menu.
There are color bars for your reference. Green color stands for regular recording,
yellow color stands for motion detection and red color stands for alarm recording. The
white means the MD and alarm record is valid. Once you have set to record when the
MD and alarm occurs, system will not record neither motion detect occurs nor the
alarm occurs.
138
Figure 3-151
Figure 3-152
3.11.4.1.1.1 Quick Setup
Copy function allows you to copy one channel setup to another. After setting in channel 1,
click Copy button, you can go to interface Figure 3-153. You can see current channel
name is grey such as channel 1. Now you can select the channel you want to paste such
as channel 5/6/7. If you want to save current setup of channel 1 to all channels, you can
click the first box “ALL”. Click the OK button to save current copy setup. Click the OK
button in the Encode interface, the copy function succeeded.
139
Figure 3-153
3.11.4.1.1.2 Redundancy
Redundancy function allows you to memorize record file in several disks. When there
is file damage occurred in one disk, there is a spare one in the other disk. You can use
this function to maintain data reliability and safety.
In the main menu, from Setting->Storage-> Schedule, you can highlight
redundancy button to enable this function.
In the main menu, from Main menu->Setting->Storage->HDD Manager, you can set
one or more disk(s) as redundant. You can select from the dropdown list. System
auto overwrites old files once hard disk is full.
Please note only read/write disk or read-only disk can backup file and support file
search function, so you need to set at least one read-write disk otherwise you can not
record video.
Note
About redundancy setup:
If current channel is not recording, current setup gets activated when the channel
begin recording the next time.
If current channel is recording now, current setup will get activated right away, the
current file will be packet and form a file, then system begins recording as you have
just set.
After all the setups please click save button, system goes back to the previous menu.
Playback or search in the redundant disk.
There are two ways for you to playback or search in the redundant disk.
Set redundant disk(s) as read-only disk or read-write disk (Main
menu->Setting->Storage->HDD Manager)). System needs to reboot to get setup
activated. Now you can search or playback file in redundant disk.
Dismantle the disk and play it in another PC.
3.11.4.1.2 Snapshot
3.11.4.1.2.1 Schedule Snapshot
On the preview interface, right click mouse and then select Manual->Record, or in the
main menu, from Setting->Storage->Record, check the box to enable snapshot
function of corresponding channels. See Figure 3-154.
140
In main menu, from Setting->Camera->Encode->Snapshot interface, here you can
input snapshot mode as regular, size, quality and frequency. See Figure 3-155.
In main menu, from Setting->Camera->Encode->Schedule interface, please enable
snapshot function. See interface on the right of Figure 3-156.
Please refer to the following figure for detailed information.
Figure 3-154
141
Figure 3-155
Figure 3-156
3.11.4.1.2.2 Trigger Snapshot
Please follow the steps listed below to enable the activation snapshot function. After
you enabled this function, system can snapshot when the corresponding alarm
occurred.
In main menu, from Setting->Camera->Encode->Snapshot interface, here you can
input snapshot mode as trigger, size, quality and frequency. See Figure 3-157.
In main menu, from Setting->Event->Detect, please enable snapshot function for
specified channels (Figure 3-158). Or In main menu, from Setting->Event->Alarm
(Figure 3-159) please enable snapshot function for specified channels.
142
Figure 3-157
Figure 3-158
143
Figure 3-159
3.11.4.1.2.3 Priority
Please note the activation snapshot has the higher priority than schedule snapshot. If
you have enabled these two types at the same time, system can activate the activation
snapshot when an alarm occurs, and otherwise system just operates the schedule
snapshot.
144
Please input the
corresponding information
here, if you just upload the
image FTP.
Figure 3-160
3.11.4.2 HDD Manager
Here is for you to view and implement hard disk management. See Figure 3-161.
You can see current HDD type, status, capacity and etc. The operation includes format
HDD, and change HDD property (read and write/read-only/redundancy).
145
Figure 3-161
3.11.4.3 Record
3.11.4.3.1 Record Control
Note:
You need to have proper rights to implement the following operations. Please make
sure the HDD has been properly installed.
There are three ways for you to go to manual record menu.
Right click mouse and then select Manual->Record.
In the main menu, from Setting->Storage->Record.
In live viewing mode, click record button in the front panel or record button in the
remote control.
System supports main stream and sub stream. There are three statuses:
schedule/manual/stop. See Figure 3-162. Please highlight icon “ ○ ” to select
corresponding channel.
Manual: The highest priority. After manual setup, all selected channels will begin
ordinary recording.
Schedule: Channel records as you have set in recording setup (Main
Menu->Setting->System->>Schedule)
Stop: Current channel stops recording.
All: Check All button after the corresponding status to enable/disable all-channel
schedule/manual record or enable/disable all channels to stop record.
146
Figure 3-162
3.11.4.3.2 Snapshot Operation
Check the corresponding box to enable/disable schedule snapshot function. See
Figure 3-163.
Figure 3-163
Tips
You can check All button after the corresponding status to enable/disable all-channel
147
snapshot function.
Figure 3-164
148
Figure 3-165
Figure 3-166
149
Click the item you can see the detailed information such as detect result. See Figure
3-167.
Figure 3-167
3.11.5 System
3.11.5.1 General
3.11.5.1.1 Device
General setting includes the following items. See Figure 3-168.
Device ID: Please input a corresponding device name here.
Device No: Here you can set device number.
Language: System supports various languages: Chinese (simplified), Chinese
(Traditional), English, Italian, Japanese, French, Spanish (All languages listed here
are optional. Slight difference maybe found in various series.)
Video standard: There are two formats: NTSC and PAL.
HDD full: Here is for you to select working mode when hard disk is full. There are two
options: stop recording or rewrite. If current working HDD is overwritten or the current
HDD is full while the next HDD is no empty, then system stops recording, If the
current HDD is full and then next HDD is not empty, then system overwrites the
previous files.
Pack duration: Here is for you to specify record duration. The value ranges from 1 to
120 minutes. Default value is 60 minutes.
Real-time playback: It is to set playback time you can view in the preview interface.
The value ranges from 5 to 60 minutes.
150
Auto logout: Here is for you to set auto logout interval once login user remains
inactive for a specified time. Value ranges from 0 to 60 minutes.
IPC Time Sync: You can input an interval here to synchronize the DVR time and IPC
time.
Navigation bar: Check the box here, system displays the navigation bar on the
interface.
Startup wizard: Once you check the box here, system will go to the startup wizard
directly when the system restarts the next time. Otherwise, it will go to the login
interface.
Mouse property: You can set double click speed via dragging the slide bard. You can
Click Default button to restore default setup.
Figure 3-168
3.11.5.1.2 Date and Time
The interface is shown as in Figure 3-169.
Date format: There are three types: YYYYY-MM-DD: MM-DD-YYYYY or
DD-MM-YYYY.
Date separator: There are three denotations to separate date: dot, beeline and
solidus.
DST: Here you can set DST time and date. Here you can set start time and end time
by setting corresponding week setup or by setting corresponding date setup.
NTP: It is to set NTP server information.
151
Figure 3-169
3.11.5.1.3 Holiday
Holiday setup interface is shown as in Figure 3-170. Click Add new holiday button, you
can input new holiday information. See Figure 3-171. Here you can set holiday name,
repeat mode and start/end time.
Note
When you enable Holiday settings and schedule setup at the same time, holiday
setting has the priority. If the selected day is a holiday, then system records as you
set in holiday setting. If it is not a holiday, system records as you set in Schedule
interface. Please note
Please note, there is no year setup on the holiday setup. For example, if you set 30th
Oct, 2012 as a holiday, then the date of 30th Oct in each year will be set as a holiday.
152
Figure 3-170
Figure 3-171
3.11.5.2 Display
3.11.5.2.1 Display
Display setup interface is shown as below. See Figure 3-172.
Time display: You can select to display time or not when system is playback.
Channel display: You can select to channel name or not when system is playback.
153
Image original rate: Check the box here, the video can be displayed at its actual size.
Transparency: Here is for you to adjust menu transparency. The higher the value is,
the more transparent the menu is.
Resolution: There are four options: 1920×1080, 1280×1024(default),1280×
720,1024×768. Please note the system needs to reboot to activate current setup.
Preview enhance: Check the box; it can optimize the video quality of the preview
video.
Video matrix: Check the box to enable video matrix function.
Figure 3-172
3.11.5.2.2 TV Adjust
Note
This function is for some series only.
Here is for you to adjust TV output setup. See Figure 3-173.
Please drag slide bar to adjust each item.
After all the setups please click OK button, system goes back to the previous menu.
154
Figure 3-173
3.11.5.2.3 Tour
Here you can activate tour function. Click Setup button, you can see an interface shown
as in Figure 3-174
Enable tour: Highlight box here to enable this function.
Interval: System supports 1/8/-window tour. Input proper interval value here. The
value ranges from 5-120 seconds. It is for schedule tour/alarm/motion detect tour.
Split: You can select window split mode from the dropdown list.
Channel group: It is to display all channel groups on current split mode. You can edit
and delete a channel group here. Double click an item in the list; you can edit its
channel group setup. Right now system max supports 32.
Add: Under specified window split mode, click it to add channel group.
Delete: Click it to remove selected channel group.
Move up: Click it to move current selected channel up.
Move down: Click it to move current selected channel down.
Default: Click it to restore default setup.
Tips:
Use mouse or Shift button to switch and button to enable /disable tour.
means the tour funciton is enabled and meas tour funciton is disabled.
155
On the navigation bar, click or to enable/disable tour function.
Figure 3-174
3.11.5.2.4 Zero-channel Encoding
Click zero-channel encoding button, you can go to the following interface. See Figure
3-175. Here you can enable and set zero-channel encoding function so that you can view
several video sources at one channel.
Enable: This function is disabled by default. Check the box here to enable this
function so that you can control the zero-channel encoding function at the WEB.
Compression: System default setup is H.264. You can set according to device
capability.
Resolution: The resolution value may vary due to different device capabilities. Please
select from the dropdown list.
Frame rate: The frame rate value may vary due to different device capabilities.
Please select from the dropdown list.
Bit Rate: The bit rate value may vary due to different device capabilities and frame
rate setups. Please select from the dropdown list.
Save: Click the Save button to save current setup. If this function is disabled, you can
not operate zero-channel encoding function at the WEB, the video is black or null
even you operate when the function is disabled. After you enabled this function, login
156
the Web and you can select zero-channel encoding mode at the right corner of the
interface . Select a mode; you can view the local preview video.
Figure 3-175
157
Move down: Click it to move current selected channel down.
Default: Click it to restore default setup.
Figure 3-176
Figure 3-177
158
Figure 3-178
3.11.5.4 RS232
RS232 interface is shown as below. There are five items. See Figure 3-179.
Function: There are various devices for you to select. Console is for you to use the
COM or mini-end software to upgrade or debug the program. The control keyboard is
for you to control the device via the special keyboard. Transparent COM (adapter) is
to connect to the PC to transfer data directly. Protocol COM is for card overlay
function. Network keyboard is for you to use the special keyboard to control the
device. PTZ matrix is to connect to the peripheral matrix control.
Baud rate: You can select proper baud rate.
Data bit: You can select proper data bit. The value ranges from 5 to 8.
Stop bit: There are two values: 1/2.
Parity: There are five choices: none/odd/even/space mark.
System default setup is:
Function: Console
Baud rate:115200
Data bit:8
Stop bit:1
Parity: None
After completing all the setups please click save button, system goes back to the previous
menu.
159
Figure 3-179
3.11.5.5 PTZ
The pan/tilt/zoom setup includes the following items. Please select channel first. See
Figure 3-180.
PTZ type: There are two options: local/remote. Please select remote if you are
connecting to the network PTZ.
Control mode: You can select control mode from the dropdown list. There are two
options: Serial/HDCVI. For HDCVI series product, please select HDCVI. The control
signal is sent to the PTZ via the coaxial cable. For the serial mode, the control signal
is sent to the PTZ via the RS485 port.
Protocol: If the control mode is HDCVI, please select HDCVI protocol. The default
setup is HDCVI3.0
Address: input corresponding PTZ address.
Baud rate: Select baud rate.
Data bit: Select data bit.
Stop bit: Select stop bit.
Parity: There are three choices: none/odd/even.
After completed all the setups please click save button, system goes back to the previous
menu.
160
Figure 3-180
For digital channel, the interface is shown as below. See Figure 3-181.
Figure 3-181
3.11.5.6 ATM/POS
161
The ATM/POS function is for financial areas. It includes Sniffer, information analysis and
title overlay function. The Sniffer mode includes COM and network.
3.11.5.6.1 COM Type
The COM interface is shown as below. See Figure 3-182.
Protocol: Please select from the dropdown list.
Setting: Click COM setting button, the interface is shown as in RS232 interface.
Please refer to Chapter 5.3.4 RS232.
Overlay channel: Please select the channel you want to overlay the card number.
Overlay mode: There are two options: preview and encode. Preview means overlay
the card number in the local monitor video. Encode means overlay the card number
in the record file.
Overlay Position: Here you can select the proper overlay position from the dropdown
list.
Figure 3-182
3.11.5.6.2 Network Type
The network type interface is shown as below. See Figure 3-183.
Please use network type if you using network to connect to the device. The interface is
generally the same as the COM mode. The protocol depends on your self-develop
protocol. The setup may vary since connected device or the protocol is not the same.
Here we take the ATM/POS protocol to continue.
Protocol: It is to set COM sniffer protocol. You need to select protocol according to
your own development situation.
162
Overlay mode: There are two options: preview and encode. Preview means overlay
the card number in the local monitor video. Encode means overlay the card number
in the record file. You can view the corresponding information when playback.
Overlay Position: Here you can select the proper overlay position from the dropdown
list.
Data group: There are total four groups IP.
Source IP: Source IP refers to host IP address that sends out information (usually it is
the device host.)
Destination IP: Destination IP refers to other systems that receive information.
Source port/destination port: Please input according to your own situation.
Record channel: It is for you to check record channel. The record channel applies to
one group (optional) only.
Frame ID: Six frame ID groups verification can guarantee information validity and
legal. You need to input start position, length, key and etc according to your
communication protocol and data packet contents.
Figure 3-183
In Figure 3-183, click data button after frame ID the interface is shown as in Figure 3-184.
Here you can set field start position, length, and overlay title.
163
Figure 3-184
3.11.5.7 Voice
The audio function is to manage audio files and set schedule play function. It is to realize
audio broadcast activation function.
3.11.5.7.1 File List
Here you can add audio file, listen to the audio file, or rename/delete audio file. Here you
can also set audio volume. See Figure 3-185.
Figure 3-185
Click Add button, you can add audio file and import the audio file via the USB device. See
Figure 3-186.
164
Figure 3-186
The audio file can be saved on the HDD or on the USB device.
In Figure 3-185, when it is HDD mode, the newly added audio file can be saved on
the HDD automatically. You do not need to connect to the USB device if you want to
use it the next time.
In Figure 3-185, when it is USB mode, after you imported, you need to connect the
USB device all the time; otherwise, the audio link function may fail. So, if you want to
use the audio trigger function, please make sure the audio file is on the UBS device
and the USB device has connected to the DVR before the DVR boots up. You need to
make sure the USB device connection is always there if you want to manage and use
the audio file function.
If there is a USB device (containing the audio file) and the HDD (containing the audio
file) at the same time, the HDD mode has higher priority. That is to say, DVR uses the
audio file from the HDD.
3.11.5.8 Account
Here is for you to implement account management. See Figure 3-187. Here you can:
Add new user
Modify user
Add group
Modify group
Modify password.
For account management please note:
For the user account name and the user group, the string max length is 6-byte. The
backspace in front of or at the back of the string is invalid. There can be backspace in
the middle. The string includes the valid character, letter, number, underline,
subtraction sign, and dot.
165
The default user amount is 64 and the default group amount is 20. System account
adopts two-level management: group and user.
For group or user management, there are two levels: admin and user.
The user name and group name can consist of eight bytes. One name can only be
used once. There are three default users: admin/888888 and hidden user “default”.
Hidden user “default” is for system interior use only and can not be deleted. When
there is no login user, hidden user “default” automatically login. You can set some
rights such as monitor for this user so that you can view some channel view without
login.
One user should belong to one group. User right can not exceed group right.
About reusable function: this function allows multiple users use the same account to
login.
About user account and MAC. When you add a new user, you can input the MAC
address of current user. Only the user of the same MAC address can access the
device remotely. (MAC address is for the device of the same LAN.) If you leave MAC
address item in blank when you add a new user, the user of any MAC address can
access the device remotely. You can set or change MAC address when you add or
modify a user. The MAC address function is also valid for PSS login. Please note
current function does not support IPV6.
After all the setups please click save button, system goes back to the previous menu.
Figure 3-187
3.11.5.8.1 Add User
166
Click modify user button in Figure 3-187 , the interface is shown as in Figure 3-188.
Please input the user name, password, select the group it belongs to from the dropdown
list.
Then you can check the corresponding rights for current user.
For convenient user management, usually we recommend the general user right is lower
than the admin account.
Username: admin. Password: admin. (administrator, local and network)
Username: 888888. Password: 888888. (administrator, local only)
Username: default. Password: default (hidden user). Hidden user “default” is for
system interior use only and can not be deleted. When there is no login user, hidden
user “default” automatically login. You can set some rights such as monitor for this
user so that you can view some channels without login.
Figure 3-188
When you create a new user, you can input the corresponding MAC address of current
user. If you leave this item in blank, any MAC address user can share this user account to
login. Please note system needs to check the validity of MAC. Only the 12-digit 0-f format
address can pass the validity verification. System only saves small character even you
input capitalized one. You can see the corresponding prompt if there is any illegal input.
Click the Set button after the period, you can set valid period to use current account. See
Figure 3-189.
167
Figure 3-189
Click Set button, you can set six periods in one day. See Figure 3-190.
Check the box after the period, you can enable current setup.
Figure 3-190
168
3.11.5.8.2 Modify user
Click , you can go to the following interface to change user information. See Figure
3-191.
For admin, 888888, and default (hidden user), you can not change period setup.
Figure 3-191
3.11.5.8.3 Change Password
In Figure 3-191, check the Modify password box, you can change password. Please input
old password, and then input new password twice to confirm.
The password can contain 32-byte and the space at the begin or at the end of the
password are null. It can contain in the middle of the password. For the user of account
right, it can change the password of other users.
169
Figure 3-192
Click add group button in Figure 3-192 , the interface is shown as below. See Figure
3-193.
Here you can input group name and then input some memo information if necessary.
There are total 98 rights such as control panel, shut down, real-time monitor, playback,
record, record file backup, PTZ, user account, system information view, alarm input/output
setup, system setup, log view, clear log, upgrade system, control device and etc.
170
Figure 3-193
Figure 3-194
171
3.11.5.9 Auto Maintain
Here you can set auto-reboot time and auto-delete old files setup. You can set to delete
the files for the specified days. See Figure 3-195.
You can select proper setup from dropdown list.
After all the setups please click save button, system goes back to the previous menu.
Figure 3-195
3.11.5.10 Config Backup
The configuration file backup interface is shown as below. See Figure 3-196.
This function allows you to import/export system configuration. You can use this function
when there are several devices need the same setup.
Export: Please connect the peripheral device first and then go to the following
interface. Click Export button, you can see there is a corresponding “Config_Time”
folder. Double click the folder, you can view some backup files.
Import: Here you can import the configuration files from the peripheral device to
current device. You need to select a folder first. You can see a dialogue box asking
you to select a folder if you are selecting a file. System pops up a dialogue box if
there is no configuration file under current folder. After successfully import, system
needs to reboot to activate new setup.
Format: Click Format button, system pops up a dialogue box for you to confirm
current operation. System begins format process after you click the OK button.
Note:
172
System can not open config backup interface again if there is backup operation in the
process.
System refreshes device when you go to the config backup every time and set
current directory as the root directory of the peripheral device.
If you go to the configuration backup interface first and then insert the peripheral
device, please click Refresh button to view the newly added device.
Figure 3-196
3.11.5.11 Default
Click default icon, system pops up a dialogue box. You can highlight to restore
default factory setup. See Figure 3-197.
Camera
Network
Event
Storage
System
173
Figure 3-197
3.11.5.12 Update
Here is for you to view hardware features, software version, built date, release SN
information and etc. You can also update system here. See Figure 3-198.
Start: Please insert the USB device that have the update file to the device and then
click the Start button to begin the update.
Important
Please make sure the upgrade file name shall be update.bin.
174
Figure 3-198
175
4 WEB OPERATION
Slightly difference may be found in the interface due to different series.
4.2 Login
Open IE and input DVR address in the address column. For example, if your DVR IP is
10.10.3.16, then please input http:// 10.10.3.16 in IE address column.
System pops up warning information to ask you whether install control or not. Please click
Install button. See Figure 4-1.
Figure 4-1
After installation, the interface is shown as below. See Figure 4-2.
Please input your user name and password.
Default factory name is admin and password is admin.
Note: For security reasons, please modify your password after you first login.
176
Figure 4-2
System pops up the following dialogue box for you to change default administrator
password. See Figure 4-3.
Figure 4-3
For you own safety, please change the default password after you first login.
Click Cancel button, system pops up the following dialogue box to confirm the exit. See
Figure 4-4.
Check the box here, system will not pop up the change password interface the next time.
177
Figure 4-4
Figure 4-5
This main window can be divided into the following sections.
Section 1: there are five function buttons: Live(chapter 4.4), setup (chapter 4.8),
search (chapter 4.10), alarm (chapter 4.11),face search (chapter 4.11) and logout
(chapter 0).
Section 2: There are channel number and one button: Start all. Start all button is to
enable/disable all-channel real-time monitor. Click it the button becomes yellow. See
Figure 4-6.
178
Figure 4-6
Please refer to Figure 4-7 for main stream and extra stream switch information.
Figure 4-7
Figure 4-8
Section 4: Instant record button. Click it, the button becomes yellow and system
begins manual record. See Figure 4-9. Click it again, system restores previous record
mode..
Figure 4-9
Section 5: Local play button.
The Web can playback the saved (Extension name is dav) files in the PC-end.
Click local play button, system pops up the following interface for you to select local play
file. See Figure 4-10.
179
Figure 4-10
Section 6: From the left to the right ,you can see video quality/fluency/ full
screen/1-window/4-window/6-window/8-window/9-window/13-window/16-window/20-
window/25-window/36-window.. You can set video fluency and real-time feature
priority.
Section 7: PTZ operation panel. Please refer to chapter 4.5 for detailed information.
Section 8: Image setup and alarm setup. Please refer to chapter 4.6 for detailed
information.
Section 9:From left to right, it is to set video quality, video latency, full screen,
1-window, 4-window.
Section 10:Zero-channel encoding. This function allows you to view several-channel
in one window. It supports 1/4-channel mode. Please go to chapter 3.11.5.2.4 to
enable zero-channel encoding function first.
1 2 3
Figure 4-11
On the top right corner, there are six unction buttons. See Figure 4-12.
180
1 2 3 4 5 6
Figure 4-12
1: Fisheye: Click to adjust fisheye installation mode and display mode. See Figure
4-13. Please note this function is for some series only.
2: Digital zoom: Click this button and then left drag the mouse in the zone to zoom in.
right click mouse system restores original status.
3: Local record. When you click local record button, the system begins recording and
this button becomes highlighted. You can go to system folder RecordDownload to
view the recorded file.
4: Snapshot picture. You can snapshot important video. All images are memorized in
system client folder PictureDownload (default).
5: Audio :Turn on or off audio.(It has no relationship with system audio setup )
6: Close video.
4.4.1 Fisheye de-warp
Fisheye de-warp interface is shown as in Figure 4-13.
Figure 4-13
There are three installation modes: ceiling mount/wall mount/ground mount. The
different installations modes have different de-warp modes.
Please refer to the following sheet for detailed information.
Installation modes Icon Note
360°panorama original view
(Ceiling mount)
181
1 de-warp window+1 panorama stretching
(Ground mount)
2 panorama stretching view
In Figure 4-14, there are one ceiling mount 360°panorama view + four de-warp
windows.
You can adjust the color pane on the left pane or use your mouse to change the
position of the small images on the right pane to realize fish eye de-warp. Please use
mouse to zoom in/out, move, rotate and etc to adjust.
Figure 4-14
182
4.5 PTZ
Before PTZ operation, please make sure you have properly set PTZ protocol. (Please
refer to chapter 4.8.5.5).
There are eight direction keys. In the middle of the eight direction keys, there is a 3D
intelligent positioning key.
Click 3D intelligent positioning key, system goes back to the single screen mode. Drag the
mouse in the screen to adjust section size. It can realize PTZ automatically.
Please refer to the following sheet for PTZ setup information.
Parameter Function
Scan Select Scan from the dropdown list.
Click Set button, you can set scan left and right limit.
Use direction buttons to move the camera to you desired location
and then click left limit button. Then move the camera again and
then click right limit button to set a right limit.
Preset Select Preset from the dropdown list.
Turn the camera to the corresponding position and Input the
preset value. Click Add button to add a preset.
Tour Select Tour from the dropdown list.
Input preset value in the column. Click Add preset button, you
have added one preset in the tour.
Repeat the above procedures you can add more presets in one
tour.
Or you can click delete preset button to remove one preset from
the tour.
Pattern Select Pattern from the dropdown list.
You can input pattern value and then click Start button to begin
PTZ movement such as zoom, focus, iris, direction and etc. Then
you can click Add button to set one pattern.
Aux Please input the corresponding aux value here.
You can select one option and then click AUX on or AUX off
button.
Light and You can turn on or turn off the light/wiper.
wiper
183
3D Intelligent Positioning
Key
Figure 4-15
4.6 Image/Relay-out
Select one monitor channel video and then click Image button in section 8, the interface is
shown as Figure 4-16.
4.6.1 Image
Here you can adjust its brightness, contrast, hue and saturation. (Current channel border
becomes green).
Or you can click Reset button to restore system default setup.
Figure 4-16
4.6.2 Relay output
Here you can enable or disable the alarm signal of the corresponding port. See Figure
4-17.
Figure 4-17
184
4.7 WAN Login
In WAN mode, after you logged in, the interface is shown as below. See Figure 4-18.
Figure 4-18
Please refer to the following contents for LAN and WAN login difference.
1) In the WAN mode, system opens the main stream of the first channel to monitor by
default. The open/close button on the left pane is null.
2) You can select different channels and different monitor modes at the bottom of the
interface.
Important
The window display mode and the channel number are by default. For example, for
the 16-channel, the max window split mode is 16.
3) Multiple-channel monitor, system adopts extra stream to monitor by default. Double
click one channel, system switches to single channel and system uses main stream to
monitor. You can view there are two icons at the left top corner of the channel number for
you reference. M stands for main stream. S stands for sub stream (extra stream).
4) If you login via the WAN mode, system does not support alarm activation to open the
video function in the Alarm setup interface.
Important
For multiple-channel monitor mode, system adopts extra stream to monitor by default.
You can not modify manually. All channels are trying to synchronize. Please note the
synchronization effect still depends on your network environments.
185
For bandwidth consideration, system can not support monitor and playback at the
same time. System auto closes monitor or playback interface when you are searching
setup in the configuration interface. It is to enhance search speed.
4.8 Setup
4.8.1 Camera
4.8.1.1 Remote Device (For digital channel only)
Remote device interface is shown as below. See Figure 4-19.
Figure 4-19
Figure 4-20
Please refer to the following sheet for log parameter information.
186
Parameter Function
Device Click Device search button, you can view the searched device
search information on the list. It includes device IP address, port, device
name, manufacturer and type.
Add Select a device in the list and then click Add button, system can
connect the device automatically and add it to the Added device list.
Or you can double click one item in the list to add a device.
Modify
Click or any device in the Added device list, you can change the
Delete Select a device in the Added device list and then click Delete button,
system can disconnect the device and remove it from the Added
device list.
Manual Click it, the interface is shown as in Figure 4-20. Here you can add
Add network camera manually.
You can select a channel from the dropdown list (Here only shows
disconnection channel.)
Note:
System supports manufactures such as Panasonic, Sony,
Dynacolor, Samsung, AXIS, Arecont, Dahua and Onvif standard
protocol.
If you do not input IP address here. System uses default IP
192.168.0.0 and system does not connect to this IP.
Can not add two devices at the same time. Click OK button here,
system only connect to the corresponding device of current
channel.
4.8.1.2 Conditions
Here you can view device property information. The setups become valid immediately
after you set.
The analog channel is shown as in Figure 4-21.
187
Figure 4-21
The digital channel is shown as in Figure 4-22.
Figure 4-22
Please refer to the following sheet for detailed information.
Parameter Function
Cable type It is to set the cable type of the corresponding analog channel.
When the setup here matches the actual cable you are using,
you can get the best image effect. The default setup is
COAXIAL. Please note this function is for some series product
only.
COAXIAL: When the corresponding channel is using
coaxial cable, please select COAXIAL.
UTP: When the corresponding channel is using UTP cable,
please select UTP. Usually we recommend 10Ohm UTP
cable.
188
Period It divides one day (24 hours) to two periods. You can set
different hue, brightness, and contrast for different periods.
Hue It is to adjust monitor video brightness and darkness level. The
default value is 50.
The bigger the value is, the large the contrast between the bright
and dark section is and vice versa.
Brightness It is to adjust monitor window brightness. The default value is 50.
The larger the number is , the bright the video is. When you
input the value here, the bright section and the dark section of
the video will be adjusted accordingly. You can use this
function when the whole video is too dark or too bright. Please
note the video may become hazy if the value is too high. The
value ranges from 0 to 100.The recommended value ranges
from 40 to 60.
Contrast It is to adjust monitor window contrast. The value ranges from 0
to 100. The default value is 50.
The larger the number is, the higher the contrast is. You can use
this function when the whole video bright is OK but the contrast
is not proper. Please note the video may become hazy if the
value is too low. If this value is too high, the dark section may
lack brightness while the bright section may over exposure .The
recommended value ranges from 40 to 60.
Saturation It is to adjust monitor window saturation. The value ranges from
0 to 100. The default value is 50.
The larger the number is, the strong the color is. This value has
no effect on the general brightness of the whole video. The
video color may become too strong if the value is too high. For
the grey part of the video, the distortion may occur if the white
balance is not accurate. Please note the video may not be
attractive if the value is too low. The recommended value ranges
from 40 to 60.
Color mode It includes several modes such as standard, color. You can
select corresponding color mode here, you can see hue,
brightness, and contrast and etc will adjust accordingly.
4.8.1.3 Encode
4.8.1.3.1 Encode
The encode interface is shown as below. See Figure 4-23.
189
Figure 4-23
Please refer to the following sheet for detailed information.
Parameter Function
190
non-important surveillance object to save the storage space.
Bit Rate Main stream: You can set bit rate here to change video
quality. The large the bit rate is , the better the quality is.
Please refer to recommend bit rate for the detailed
information.
Extra stream: In CBR, the bit rate here is the max value.
In dynamic video, system needs to low frame rate or
video quality to guarantee the value. The value is null in
VBR mode.
Reference bit Recommended bit rate value according to the resolution and
rate frame rate you have set.
I Frame Here you can set the P frame amount between two I frames. The
value ranges from 1 to 150. Default value is 50.
Recommended value is frame rate *2.
Audio source Please select from the dropdown list. There are two options:
Normal/HDCVI. In the normal mode, the audio signal comes
from the Audio In. In the HDCVI mode, the audio signal comes
from the coaxial cable of the camera.
Watermark This function allows you to verify the video is tampered or not.
enable Here you can select watermark bit stream, watermark mode and
watermark character. Default character is DigitalCCTV. The max
length is 85-digit. The character can only include number,
character and underline.
4.8.1.3.2 Snapshot
The snapshot interface is shown as in Figure 4-24.
191
Figure 4-24
Please refer to the following sheet for detailed information.
Parameter Function
Snapshot type There are two modes: Regular (schedule) and Trigger.
Regular snapshot is valid during the specified period you
set.
Trigger snapshot only is valid when motion detect alarm,
tampering alarm or local activation alarm occurs.
Image size It is the same with the resolution of the main stream.
Quality It is to set the image quality. There are six levels.
Figure 4-25
192
Please refer to the following sheet for detailed information.
Parameter Function
Cover-area Check Preview or Monitor first.
Click Set button, you can privacy mask the specified video in the
preview or monitor video.
System max supports 4 privacy mask zones.
Time Title You can enable this function so that system overlays time
information in video window.
You can use the mouse to drag the time title position.
You can view time title on the live video of the WEB or the
playback video.
Channel Title You can enable this function so that system overlays channel
information in video window.
You can use the mouse to drag the channel title position.
You can view channel title on the live video of the WEB or the
playback video.
4.8.1.3.4 Path
The storage path interface is shown as in Figure 4-26.
Here you can set snap image saved path ( in the preview interface) and the record
Figure 4-26
4.8.1.4 Channel Name
Here you can set channel name. See Figure 4-27.
Please note this function is for analog channel only. The digital channel name here is
read-only.
193
Figure 4-27
4.8.1.5 Channel Type
It is to set channel type.
For analog channel (CVBS signal or HDCVI HD signal), you can select coaxial cable
or UTP cable. Please check first and then save setup. There is no need to reboot.
You can switch analog channel type to digital channel type if you want to connect to
network camera. The IP channel shall start from the last channel. System needs to
reboot to activate current setup.
Note
If there is no connected channel, the channel type here just displays previous connection
record. System supports self-adaptive after camera connection.
The interface is shown as in Figure 4-28 (penta-brid series product) and Figure 4-29
(general series product).
194
Figure 4-28
Figure 4-29
Important
Add/cancel IP CAM function is for some series product only.
Add IP CAM: Click it; you can add corresponding X IP channels. Here X refers to the
product channel amount. Please refer to chapter Error! Reference source not
found. Specifications for IP channel amount information. System needs to restart to
195
activate new setup.
For example, there is a 4-channel analog device, after the A/D switch, it can max
supports 4 analog channels and 4 IP channels. Once it has become the 3+1 mode (3
4.8.2 Network
4.8.2.1 TCP/IP
The single-Ethernet port interface is shown as in Figure 4-30.
Figure 4-30
The dual-Ethernet port interface is shown as in Figure 4-31.
196
Figure 4-31
Please refer to the following sheet for detailed information.
Parameter Function
Mode There are two modes: static mode and the DHCP mode.
The IP/submask/gateway are null when you select the
DHCP mode to auto search the IP.
If you select the static mode, you need to set the
IP/submask/gateway manually.
If you select the DHCP mode, you can view the
IP/submask/gateway from the DHCP.
If you switch from the DHCP mode to the static mode, you
need to reset the IP parameters.
Besides, IP/submask/gateway and DHCP are read-only
when the PPPoE dial is OK.
Mac Address It is to display host Mac address.
IP Version It is to select IP version. IPV4 or IPV6.
You can access the IP address of these two versions.
IP Address Please use the keyboard to input the corresponding number to
modify the IP address and then set the corresponding subnet
mask and the default gateway.
Preferred DNS DNS IP address.
Alternate DNS Alternate DNS IP address.
For the IP address of IPv6 version, default gateway, preferred DNS and
alternate DNS, the input value shall be 128-digit. It shall not be left in blank.
LAN load System can process the downloaded data first if you enable this
function. The download speed is 1.5X or 2.0X of the normal
speed.
4.8.2.2 Connection
The connection interface is shown as in Figure 4-32.
197
Figure 4-32
Please refer to the following sheet for detailed information.
Parameter Function
Max connection It is the max Web connection for the same device. The value
ranges from 1 to 120. The default setup is 120.
TCP port The default value is 37777. You can input the actual port
number if necessary.
UDP port The default value is 37778. You can input the actual port
number if necessary.
HTTP port The default value is 80. You can input the actual port number if
necessary.
HTTPS The default value is 443. You can input the actual port number if
necessary.
RTSP port The default value is 554.
4.8.2.3 WIFI
Please note this function is for the device of WIFI module.
The WIFI interface is shown as in Figure 4-33.
Figure 4-33
198
Please check the box to enable WIFI function and then click the Search SSID button. Now
you can view all the wireless network information in the following list. Double click a name
to connect to it. Click Refresh button, you can view latest connection status.
4.8.2.4 3G
4.8.2.4.1 CDMA/GPRS
The CDMA/GPRS interface is shown as in Figure 4-34.
Figure 4-34
Please refer to the following sheet for detailed information.
Parameter Function
WLAN type Here you can select 3G network type to distinguish the 3G
module from different ISP. The types include WCDMA,
CDMA1x and etc.
APN/Dial No. Here is the important parameter of PPP.
Authorization It includes PAP,CHAP,NO_AUTH.
Pulse interval It is to set time to end 3G connection after you close extra
stream monitor. For example, if you input 60 here, system ends
3G connection after you close extra stream monitor 60 seconds.
Important
If the pulse interval is 0, then system does not end 3G connection after
you close the extra stream monitor.
Pulse interval here is for extra stream only. This item is null if you are
using main stream to monitor.
4.8.2.4.2 Mobile
The mobile setup interface is shown as in Figure 4-35.
Here you can activate or turn off the 3G connected phone or mobile phone, or the phone
you set to get alarm message.
199
Figure 4-35
4.8.2.5 PPPoE
The PPPoE interface is shown as in Figure 4-36.
Input the PPPoE user name and password you get from the IPS (internet service provider)
and enable PPPoE function. Please save current setup and then reboot the device to get
the setup activated.
Device connects to the internet via PPPoE after reboot. You can get the IP address in the
WAN from the IP address column.
Please note, you need to use previous IP address in the LAN to login the device.
Please go to the IP address item to via the device current device information. You
can access the client-end via this new address.
Figure 4-36
4.8.2.6 DDNS
The DDNS interface is shown as in Figure 4-37.
The DDNS is to set to connect the various servers so that you can access the system via
the server. Please go to the corresponding service website to apply a domain name and
then access the system via the domain. It works even your IP address has changed.
Please select DDNS from the dropdown list (Multiple choices). Before you use this
function, please make sure your purchased device support current function.
200
Figure 4-37
Please refer to the following sheet for detailed information.
Parameter Function
Server Type You can select DDNS protocol from the dropdown list and then
enable DDNS function.
Server IP DDNS server IP address
Server Port DDNS server port.
Domain Name Your self-defined domain name.
User The user name you input to log in the server.
Password The password you input to log in the server.
Update period Device sends out alive signal to the server regularly.
You can set interval value between the device and DDNS server
here.
Quick DDNS and Client-end Introduction
1) Background Introduction
Device IP is not fixed if you use ADSL to login the network. The DDNS function allows you
to access the DVR via the registered domain name. Besides the general DDNS, the quick
DDNS works with the device from the manufacturer so that it can add the extension
function.
2) Function Introduction
The quick DDNS client has the same function as other DDNS client end. It realizes the
bonding of the domain name and the IP address. Right now, current DDNS server is for
our own devices only. You need to refresh the bonding relationship of the domain and the
IP regularly. There is no user name, password or the ID registration on the server. At the
same time, each device has a default domain name (Generated by MAC address) for your
option. You can also use customized valid domain name (has not registered.).
3) Operation
Before you use Quick DDNS, you need to enable this service and set proper server
address, port value and domain name.
Server address:www.quickddns.com
Port number:80
Domain name:There are two modes: Default domain name and customized domain
name.
201
Except default domain name registration, you can also use customized domain name
(You can input your self-defined domain name.) After successful registration, you can
use domain name to login installed of the device IP.
User name: It is optional. You can input your commonly used email address.
Important
Do not register frequently. The interval between two registrations shall be more than
60 seconds. Too many registration requests may result in server attack.
System may take back the domain name that is idle for one year. You can get a
notification email before the cancel operation if your email address setup is OK.
4.8.2.7 IP filter
The IP filter interface is shown as in Figure 4-38.
After you enabled trusted sites function, only the IP listed below can access current DVR.
If you enable blocked sites function, the following listed IP addresses can not access
current DVR.
Figure 4-38
4.8.2.8 Email
The email interface is shown as in Figure 4-39.
202
Figure 4-39
Please refer to the following sheet for detailed information.
Parameter Function
Enable Please check the box here to enable email function.
SMTP Server Input server address and then enable this function.
Attachment System can send out the email of the snapshot picture once
you check the box here.
Receiver Input receiver email address here. Max three addresses.
It supports SSL, TLS email box.
Interval The send interval ranges from 0 to 3600 seconds. 0 means
there is no interval.
Please note system will not send out the email immediately
when the alarm occurs. When the alarm, motion detection or
the abnormity event activates the email, system sends out the
email according to the interval you specified here. This
function is very useful when there are too many emails
activated by the abnormity events, which may result in heavy
load for the email server.
203
Parameter Function
Health mail Please check the box here to enable this function.
enable
Update period This function allows the system to send out the test email to
(interval) check the connection is OK or not.
Please check the box to enable this function and then set the
corresponding interval.
System can send out the email regularly as you set here.
Email test The system will automatically sent out a email once to test the
connection is OK or not .Before the email test, please save the
email setup information.
4.8.2.9 FTP
The FTP interface is shown as in Figure 4-40.
It is to set FTP IP, port and etc for remote storage.
Figure 4-40
4.8.2.10 UPnP
It allows you to establish the mapping relationship between the LAN and the public
network.
Here you can also add, modify or remove UPnP item. See Figure 4-41.
In the Windows OS, From Start->Control Panel->Add or remove programs. Click the
“Add/Remove Windows Components” and then select the “Network Services” from
the Windows Components Wizard.
Click the Details button and then check the “Internet Gateway Device Discovery and
Control client” and “UPnP User Interface”. Please click OK to begin installation.
Enable UPnP from the Web. If your UPnP is enabled in the Windows OS, the DVR
can auto detect it via the “My Network Places”
204
Figure 4-41
4.8.2.11 SNMP
The SNMP interface is shown as in Figure 4-42.
The SNMP allows the communication between the network management work station
software and the proxy of the managed device. It is reserved for the 3 rd party to develop.
Figure 4-42
Please refer to the following sheet for detailed information.
Parameter Function
SNMP Port The listening port of the proxy program of the device. It is a
UDP port not a TCP port. The value ranges from 1 to 65535.
The default value is 161
Read Community It is a string. It is a command between the manage process
and the proxy process. It defined the authentication, access
control and the management relationship between one proxy
and one group of the managers. Please make sure the device
and the proxy are the same.
The read community will read all the objects the SNMP
supported in the specified name. The default setup is public.
Write Community It is a string. It is a command between the manage process
and the proxy process. It defined the authentication, access
control and the management relationship between one proxy
205
Parameter Function
and one group of the managers. Please make sure the device
and the proxy are the same.
The read community will read/write/access all the objects the
SNMP supported in the specified name. The default setup is
write.
Trap address The destination address of the Trap information from the proxy
program of the device.
Trap port The destination port of the Trap information from the proxy
program of the device. It is for the gateway device and the
client-end PC in the LAN to exchange the information. It is a
non-protocol connection port. It has no effect on the network
applications. It is a UDP port not TCP port. The value ranges
from 1 to 165535. The default value is 162.
SNMP version Check V1, system only processes the information of V1.
Check V2, system only processes the information of V2.
4.8.2.12 Multicast
The multicast interface is shown as in Figure 4-43.
Multicast is a transmission mode of data packet. When there is multiple-host to receive the
same data packet, multiple-cast is the best option to reduce the broad width and the CPU
load. The source host can just send out one data to transit. This function also depends
on the relationship of the group member and group of the outer.
Figure 4-43
4.8.2.13 Auto Register
The auto register interface is shown as below. See Figure 4-44.
This function allows the device to auto register to the proxy you specified. In this way, you
can use the client-end to access the DVR and etc via the proxy. Here the proxy has a
switch function. In the network service, device supports the server address of IPv4 or
domain.
Please follow the steps listed below to use this function.
Please set proxy server address, port, and sub-device name at the device-end. Please
enable the auto register function, the device can auto register to the proxy server.
Figure 4-44
206
4.8.2.14 Alarm Centre
The alarm center interface is shown as below. See Figure 4-45.
This interface is reserved for you to develop. System can upload alarm signal to the alarm
center when local alarm occurs.
Before you use alarm center, please set server IP, port and etc. When an alarm occurs,
system can send out data as the protocol defined, so the client-end can get the data.
Figure 4-45
4.8.2.15 P2P
You can use your cell phone to scan the QR code and add it to the cell phone client.
Via the SN from scanning the QR code, you can access the device in the WAN. Please
refer to the P2P operation manual included in the resources CD.
The P2P interface is shown as in Figure 4-46.
Check the Enable box to enable P2P function and then click the Save button. Now you
can view the device status and SN.
Figure 4-46
4.8.2.16 HTTPS
In this interface, you can set to make sure the PC can successfully login via the HTTPS. It
is to guarantee communication data security. The reliable and stable technology can
secure the user information security and device safety. See Figure 4-47.
Note
You need to implement server certificate again if you have changed device IP.
207
You need to download root certificate if it is your first time to use HTTPS on
current PC.
Figure 4-47
4.8.2.16.1 Create Server Certificate
If it is your first time to use this function, please follow the steps listed below.
Figure 4-48
You can see the corresponding prompt. See Figure 4-49. Now the server certificate is
successfully created.
Figure 4-49
208
Figure 4-50
Click Open button, you can go to the following interface. See Figure 4-51.
Figure 4-51
Click Install certificate button, you can go to certificate wizard. See Figure 4-52.
209
Figure 4-52
Click Next button to continue. Now you can select a location for the certificate. See Figure
4-53.
Figure 4-53
Click Next button, you can see the certificate import process is complete. See Figure 4-54.
210
Figure 4-54
Click Finish button, you can see system pops up a security warning dialogue box. See
Figure 4-55.
Figure 4-55
Click Yes button, system pops up the following dialogue box, you can see the certificate
download is complete. See Figure 4-56.
Figure 4-56
4.8.2.16.3 View and set HTTPS port
From Setup->Network->Connection, you can see the following interface. See Figure 4-57.
211
You can see HTTPS default value is 443.
Figure 4-57
4.8.2.16.4 Login
Open the browser and then input https://xx.xx.xx.xx:port.
xx.xx.xx.xx: is your device IP or domain mane.
Port is your HTTPS port. If you are using default HTTPS value 443, you do not need to
add port information here. You can input https://xx.xx.xx.xx to access.
Now you can see the login interface if your setup is right.
4.8.3 Event
4.8.3.1 Video detect
4.8.3.1.1 Motion Detect
The motion detect interface is shown as in Figure 4-58.
212
Figure 4-58
Figure 4-59
213
Figure 4-60
Figure 4-61
Please refer to the following sheet for detailed information.
Parameter Function
Enable You need to check the box to enable motion detection function.
Please select a channel from the dropdown list.
214
Parameter Function
Anti-dither System only memorizes one event during the anti-dither period.
The value ranges from 5s to 600s.
Sensitivity There are six levels. The sixth level has the highest sensitivity.
Region If you select motion detection type, you can click this button to set
motion detection zone. The interface is shown as in Figure 4-60.
Here you can set motion detection zone. There are four zones for
you to set. Please select a zone first and then left drag the mouse
to select a zone. The corresponding color zone displays different
detection zone. You can click Fn button to switch between the arm
mode and disarm mode. In arm mode, you can click the direction
buttons to move the green rectangle to set the motion detection
zone. After you completed the setup, please click ENTER button to
exit current setup. Do remember click save button to save current
setup. If you click ESC button to exit the region setup interface
system will not save your zone setup.
Record System auto activates motion detection channel(s) to record once
channel an alarm occurs. Please note you need to set motion detect record
period and go to Storage-> Schedule to set current channel as
schedule record.
Record Delay System can delay the record for specified time after alarm ended.
The value ranges from 10s to 300s.
Alarm out Enable alarm activation function. You need to select alarm output
port so that system can activate corresponding alarm device when
an alarm occurs.
Latch System can delay the alarm output for specified time after an
alarm ended. The value ranges from 1s to 300s.
Video Matrix This function is for motion detect only. Check the box here to
enable video matrix function. Right now system supports
one-channel tour function. System takes “first come and first
serve” principle to deal with the activated tour. System will process
the new tour when a new alarm occurs after previous alarm ended.
Otherwise it restores the previous output status before the alarm
activation.
Snapshot You need to check the box here to enable this function. You can
set corresponding channel to snapshot when motion detect alarm
occurs.
Show System can pop up a message to alarm you in the local host
message screen if you enabled this function.
Buzzer Check the box here to enable this function. The buzzer beeps
when an alarm occurs.
Alarm upload System can upload the alarm signal to the center (Including alarm
center.
Message When 3G network connection is OK, system can send out a
message when motion detect occurs.
Send Email If you enabled this function, System can send out an email to alert
you when an alarm occurs.
215
Tour You need to check the box here to enable this function. System
begins 1-wiindow or multiple-window tour display among the
channel(s) you set to record when an alarm occurs.
PTZ Here you can set PTZ movement when an alarm occurs. Such as
Activation go to preset X. See Figure 4-61.
Log Check the box here, system can record motion detect event log.
Figure 4-62
4.8.3.1.3 Tampering
The tampering interface is shown as in Figure 4-63.
After analysis video, system can generate a tampering alarm when the detected moving
signal reached the sensitivity you set here.
For detailed setups, please refer to chapter 4.8.3.1.1 motion detect for detailed
information.
216
Figure 4-63
4.8.3.1.4 Diagnosis
System can trigger an alarm when the stripe, noise, color cast, out of focus, over
exposure event occurred. See Figure 4-64.
Figure 4-64
Click Set button, you can check the corresponding box to select diagnosis type. See
Figure 4-65.
217
Figure 4-65
Note
Video diagnosis alarm can trigger PTZ preset, tour, and pattern.
For detailed setups, please refer to chapter 4.8.3.1.1 motion detect for detailed
information.
Important
The intelligence function is optional.
The different series products support different IVS functions. Please refer to
your purchased product actual interface for detailed information.
The IVS function supports 1 analog channel only. Right now some series
product support IP channel.
Once any object violates the rule, the DVR can trigger an alarm and alert you as the
specified alarm mode.
From main menu->Setup->Event->IVS, you can see the following interface. Here you can
set behavior analytics rule. See Figure 4-66.
Please follow the steps listed below.
1) Please select a channel from the dropdown list.
218
Figure 4-66
4.8.3.2.1 Tripwire
Note:
The tripwire function is valid once your network camera or your DVR supports this
function.
If your purchased DVR supports the tripwire function, it supports one analog channel.
It is not for the digital channel.
From main menu->Setup->Event->IVS->Tripwire, you can see the following interface. See
Figure 4-67.
System generates an alarm once there is any object crossing the tripwire in the specified
direction.
219
Figure 4-67
Check the Tripwire box to enable tripwire function.
Select SN (Line1/2/3/4) and direction, and then input customized rule name.
No. and Line1/2/3/4: System supports four tripwires. Each SN stands for one tripwire.
Direction: There are three options: A->B, B->A, both. System can generate an alarm
once there is any object crossing in the specified direction.
Now you can draw a rule. Click Draw rule button and then left click mouse to draw a
tripwire. The tripwire can be a direct line, curve or polygon. Right click mouse to complete.
See Figure 4-68.
Figure 4-68
220
Click to draw filter object. See Figure 4-69.
Figure 4-69
Select the blue line and then use mouse to adjust zone size.
Note
Each rule can set two sizes (min size/max size). Once the object is smaller than the min
size or larger than the max size, there is no alarm. Please make sure the max size is
larger than the min size.
Click Ok to complete the rule setup.
For detailed setups, please refer to chapter 4.8.3.1.1 motion detect for detailed
information.
221
Figure 4-70
Check the Intrusion box to enable intrusion function.
Select SN (Area1/2/3/4) and direction, and then input customized rule name.
No. and Area1/2/3/4: System supports four zones. Each SN stands for one zone.
Direction: There are three options: A->B, B->A, both. System can generate an alarm
once there is any object enter/exit (Or both) the zone.
Now you can draw a rule. Left click mouse to draw a line first and then right click mouse to
draw another line until you draw a rectangle, you can right click mouse to exit.
Click Ok to complete the rule setup.
222
Figure 4-71
For detailed setups, please refer to chapter 4.8.3.1.1 motion detect for detailed
information.
223
Figure 4-72
Check the Object box to enable object detect function.
Select SN (object1/2/3/4) and rule type, and then input customized rule name.
No. and Object1/2/3/4: System supports four zones. Each SN stands for one zone.
Rule type: Please select from the dropdown list. There are two types: Missing object
detect/abandoned object detect.
Period: It refers to the object in/out the zone time.
224
Figure 4-73
Now you can draw a rule. Left click mouse to draw a line, until you draw a rectangle, you
can right click mouse.
Click Ok to complete the rule setup.
For detailed setups, please refer to chapter 4.8.3.1.1 motion detect for detailed
information.
The face detection function is optional. The intelligence function and the
human face detection can not be valid at the same time!
When camera detects human face, system can draw a rectangle around the human face
and generate an alarm.
From main menu->Setup->Event->Face detect, the interface is shown as in Figure 4-74.
Enable face boost: Check the box here, system can enhance the human face display
pane.
Sensitivity: System supports 6 levels. The sixth level has the highest sensitivity.
For detailed setups, please refer to chapter 4.8.3.1.1.
225
Figure 4-74
4.8.3.4 Alarm
Before operation, please make sure you have properly connected alarm devices such
as buzzer. The input mode includes local alarm and network alarm.
4.8.3.4.1 Local Alarm
The local alarm interface is shown as in Figure 4-75. It refers to alarm from the local
device.
226
Figure 4-75
Figure 4-76
227
Figure 4-77
Please refer to the following sheet for detailed information.
Parameter Function
Enable You need to check the box to enable this function.
Please select a channel from the dropdown list.
Period This function becomes activated in the specified periods.
There are six periods in one day. Please draw a circle to
enable corresponding period.
Select date. If you do not select, current setup applies to
today only. You can select all week column to apply to the
whole week.
Click OK button, system goes back to local alarm
interface, please click save button to exit.
Anti-dither System only memorizes one event during the anti-dither
period. The value ranges from 5s to 600s.
Sensor type There are two options: NO/NC.
228
Parameter Function
Buzzer Check the box here to enable this function. The buzzer
beeps when an alarm occurs.
Alarm upload System can upload the alarm signal to the center
(Including alarm center).
Send Email If you enabled this function, System can send out an email
to alert you when an alarm occurs.
Tour You need to check the box here to enable this function.
System begins 1-wiindow or multiple-window tour display
among the channel(s) you set to record when an alarm
occurs.
PTZ Activation Here you can set PTZ movement when an alarm occurs.
Such as go to preset X.
Log Check the box here, system can record local alarm event
log.
Figure 4-78
4.8.3.4.3 IPC External Alarm
IPC external alarm interface is shown as below. See Figure 4-79. For setup information,
229
please refer to chapter 4.8.3.4.1.
Figure 4-79
4.8.3.4.4 IPC Offline Alarm
IPC offline alarm is shown as in Figure 4-80. For setup information, please refer to chapter
4.8.3.4.1.
Figure 4-80
230
4.8.3.5 Abnormality
It includes four types: HDD/Network/User/Device. See Figure 4-81 through Figure 4-84.
HDD includes: No disk, disk error, disk no space.
Network includes net disconnection, IP conflict, and MAC conflict.
User: It includes illegal login.
Device: It includes device temperature alarm, fan alarm and etc.
Figure 4-81
Figure 4-82
231
Figure 4-83
Figure 4-84
Please refer to the following sheet for detailed information.
232
Parameter Function
Event Type The abnormal events include: No disk, disk error, disk no space, net
disconnection, IP conflict and MAC conflict.
You can set one or more items here.
Less than: You can set the minimum percentage value here (For disk
not space only). The device can alarm when capacity is not sufficient.
You need to draw a circle to enable this function.
Enable Check the box here to enable selected function.
Alarm Out Please select corresponding alarm output channel when an alarm
occurs. You need to check the box to enable this function.
Latch The alarm output can delay for the specified time after an alarm stops. The
value ranges from 0s to 300s. The default setup is 10 seconds. The o
second means there is no delaying time.
Attempt(s) It is to set login attempt times. Once the login attempt exceeds the
threshold you set here, current account will be locked. This function is
for illegal login only.
Lock time It is to set account lock time once its login attempt has exceeded the
threshold you set. This function is for illegal login only.
High In Device interface (Figure 4-84), select High temperature from the
temperature dropdown list, and then input the max temperature. The value ranges
from 30 ℃ ~ 90 ℃ . Device can trigger an alarm once the case
temperature is higher than the value you set.
Fan speed In Device interface (Figure 4-84), select Fan speed abnormal from the
abnormal dropdown list, and then click the OK button after the Fan calibration. It
can correct fan manually. Please note we recommend this function after
you replaced or maintained the fan.
Show System can pop up a message to alarm you in the local host screen if
message you enabled this function.
Alarm System can upload the alarm signal to the center (Including alarm
upload center.
Send Email If you enabled this function, System can send out an email to alert you
when an alarm occurs.
Buzzer Check the box here to enable this function. The buzzer beeps when an
alarm occurs.
Log Check the box here, system can record the network event alarm log.
233
Figure 4-85
4.8.4 Storage
4.8.4.1 Schedule
4.8.4.1.1 Schedule Record
In this interfaces, you can add or remove the schedule record setup. See Figure 4-86.
There are three record modes: general (auto), motion detect and alarm. There are six
periods in one day.
You can view the current time period setup from the color bar.
Green color stands for the general record/snapshot.
Yellow color stands for the motion detect record/snapshot..
Red color stands for the alarm record/snapshot.
Blue color stands for MD&alarm record/snapshot.
234
Figure 4-86
Figure 4-87
Figure 4-88
Please refer to the following sheet for detailed information.
235
Parameter Function
Channel Please select a channel from the dropdown list.
Pre-record Please input pre-record time here. The value ranges from 0 to 30.
Redundancy Check the box here to enable redundancy function. Please note this
function is null if there is only one HDD.
Snapshot Check the box here to enable snapshot function.
Holiday Check the box here to enable holiday function.
Setup Click the Setup button, you can set record period. See Figure 4-87.
(Sunday to There are six periods in one day. If you do not check the date at the
Saturday) bottom of the interface, current setup is for today only.
Please click Save button and then exit.
Setup Click the Setup button, you can set record period. See Figure 4-87.
(Holiday) There are six periods in one day. If you check Holiday box, current
channel shall record as your holiday setup here.
Copy Copy function allows you to copy one channel setup to another. After
setting in channel, click Copy button, you can go to interface Figure
4-88. You can see current channel name is grey such as channel 1.
Now you can select the channel you want to paste such as channel
5/6/7. If you want to save current setup of channel 1 to all channels,
you can click the first box “ALL”. Click the OK button to save current
copy setup. Click the OK button in the Encode interface, the copy
function succeeded.
4.8.4.1.2 Schedule snapshot
The schedule snapshot interface is shown as below. See Figure 4-89.
Figure 4-89
For detailed operation information, please refer to chapter 4.8.4.1.1.
4.8.4.2 HDD Manage
236
The interface is shown as in Figure 4-90. Here you can see HDD information. You can
also operate the read-only, read-write, redundancy (if there are more than on HDD) and
format operation.
Figure 4-90
Figure 4-91
Please refer to the following sheet for detailed information.
Parameter Function
Channel Here you can view channel number.
The number displayed here is the max channel amount of your
device.
Status There are three statuses: schedule, manual and stop.
Schedule System enables auto record function as you set in record schedule
setup (general, motion detect and alarm).
237
Manual It has the highest priority.
Enable corresponding channel to record no matter what period
applied in the record setup.
Stop Stop current channel record no matter what period applied in the
record setup.
Start all/ Check the corresponding All button, you can enable or disable all
stop all channels record.
4.8.5 Setting
4.8.5.1 General
The general interface includes general, date/time and holiday setup.
4.8.5.1.1 General
The general interface is shown as in Figure 4-92.
Figure 4-92
Please refer to the following sheet for detailed information.
Parameter Function
Device ID It is to set device name.
238
HDD full Here is for you to select working mode when hard disk is full. There
are two options: stop recording or rewrite. If current working HDD is
overwritten or the current HDD is full while the next HDD is no empty,
then system stops recording, If the current HDD is full and then next
HDD is not empty, then system overwrites the previous files.
Pack Here is for you to specify record duration. The value ranges from 1 to
duration 120 minutes. Default value is 60 minutes.
Figure 4-93
Please refer to the following sheet for detailed information.
Parameter Function
Date format Here you can select date format from the dropdown list.
239
DST Here you can set day night save time begin time and end time. You
can set according to the date format or according to the week format.
NTP You can check the box to enable NTP function.
Interval It is to set the sync periods between the device and the time server.
Figure 4-94
4.8.5.2 Display
Display interface includes GUI, TV adjust, Tour and zero-channel encoding.
4.8.5.2.1 Display
Here you can set background color and transparency level. See Figure 4-95.
Figure 4-95
240
Please refer to the following sheet for detailed information.
Parameter Function
Resolution There are four options: 1920×1080,1280 × 1024(default),1280 ×
720,1024×768. Please note the system needs to reboot to activate
current setup.
Transparency Here is for you to adjust transparency. The value ranges from 128
to 255.
Time Check the box here, you can view system time and channel
title/channel number on the monitor video.
title
Image Check the box; you can optimize the margin of the preview video.
enhance
4.8.5.2.2 TV Adjust
Note
This function is for some series product only.
It is to set TV output region. See Figure 4-96.
Figure 4-96
4.8.5.2.3 Tour
The tour interface is shown as in Figure 4-97. Here you can set tour interval, split mode,
motion detect tour and alarm tour mode.
241
Figure 4-97
Please refer to the following sheet for detailed information.
Parameter Function
Enable tour Check the box here to enable tour function.
Interval Here is for you to adjust transparency. The value ranges from 5 to
120s. The default setup is 5s.
Split Here you can set window mode and channel group. System can
support 1/4/8/9/16/25/36-window according to device channel
amount.
Motion Here you can set motion detect tour/alarm tour window mode.
tour/Alarm System supports 1/8-window now.
tour
242
Figure 4-98
Please refer to the following sheet for detailed information.
Parameter Function
Enable This function is disabled by default. Check the box here to enable
this function so that you can control the zero-channel encoding
function at the WEB.
Compression System default setup is H.264. You can set according to device
capability.
Resolution The resolution value may vary due to different device capabilities.
Please select from the dropdown list.
Frame rate The frame rate value may vary due to different device capabilities.
Please select from the dropdown list.
Bit Rate The default setup is 1024Kb/S. The bit rate value may vary due to
different device capabilities and frame rate setups. Please select
from the dropdown list.
4.8.5.3 Video Matrix
The interface is shown as in Figure 4-99.
Here you can set video output channel and interval.
243
Figure 4-99
Please refer to the following sheet for detailed information.
Parameter Function
Enable Check the box here to enable this function.
Interval It is to set the interval from current channel group to the next
channel group.
Window split Support 1-window split only.
Delete
Select a channel group and then click to delete it.
Up/Down
Click or to adjust channel tour sequence.
Add channel group
Click ,you can see system pops up the following dialogue box. See Figure 4-100.
Please select the channels and then click OK button.
Figure 4-100
Delete channel group
244
Select a channel group and then click ,you can delete it.
Figure 4-101
Adjust channel group sequence.
4.8.5.4 RS232
The RS232 interface is shown as in Figure 4-102.
Figure 4-102
Please refer to the following sheet for detailed information.
Parameter Function
Protocol Select the corresponding dome protocol.
Default setup is console.
Baud Rate Select the baud rate.
Default setup is 115200.
Data Bit The value ranges from 5 to 8.
Default setup is 8.
Stop bit There are two options: 1/2.
Default setup is 1.
Parity There are five options: none/odd/even/space/mark.
245
Parameter Function
Default setup is none.
4.8.5.5 PTZ
The PTZ interface is shown as in Figure 4-103 and Figure 4-104.
Before setup, please check the following connections are right:
PTZ and decoder connection is right. Decoder address setup is right.
Decoder A (B) line connects with DVR A (B) line.
Click Save button after you complete setup, you can go back to the monitor interface to
control speed dome.
Figure 4-103
Figure 4-104
Please refer to the following sheet for detailed information.
Parameter Function
Channel Select speed dome connected channel.
PTZ type There are two types: local/remote. Please select local mode if you are
connect RS485 cable to connect to the Speed dome (PTZ). Please
select remote mode if you are connecting to the network PTZ camera.
246
Parameter Function
Control You can select control mode from the dropdown list. There are two
mode options: Serial/HDCVI. For HDCVI series product, please select
HDCVI. The control signal is sent to the PTZ via the coaxial cable. For
the serial mode, the control signal is sent to the PTZ via the RS485
port.
Protocol Please select protocol from the dropdown list.
If the control mode is HDCVI, please select HDCVI protocol. The
default setup is HDCVI3.0.
Address Set corresponding dome address. Default value is 1. Please note
your setup here shall comply with your dome address; otherwise
you can not control the speed dome.
Baud Rate Select the dome baud rate. Default setup is 9600.
Data Bit Default setup is 8. Please set according to the speed dome dial switch
setup.
Stop bit Default setup is 1. Please set according to the speed dome dial switch
setup.
Parity Default setup is none. Please set according to the speed dome dial
switch setup.
4.8.5.6 ATM/POS
The ATM/POS function is for financial areas. It includes Sniffer, information analysis and
title overlay function. The Sniffer mode includes COM and network.
4.8.5.6.1 COM Type
The COM interface is shown as below. See Figure 4-105.
Protocol: Please select from the dropdown list according to your actual situation.
Overlay channel: Please select the channel you want to overlay the card number.
Overlay mode: There are two options: preview and encode. Preview means overlay
the card number in the local monitor video. Encode means overlay the card number
in the record file.
Overlay Position: Here you can select the proper overlay position from the dropdown
list.
247
Figure 4-105
4.8.5.6.2 Network Type
The network type interface is shown as below. See Figure 4-106.
Here we take the ATM/POS protocol to continue.
There are two types: with or without the protocol according to client’s requirements.
With the protocol
For ATM/POS with the protocol, you just need to set the source IP, destination IP
(sometimes you need to input corresponding port number).
Figure 4-106
Without the protocol
248
For the ATM/POS without the protocol, the interface is shown as in Figure 4-107.
Source IP refers to host IP address that sends out information (usually it is the device
host.)
Destination IP refers to other systems that receive information.
Usually you do not need to set source port and target port.
There are total four groups IP. The record channel applies to one group (optional) only.
Six frame ID groups verification can guarantee information validity and legal.
Figure 4-107
4.8.5.7 Voice
The audio function is to manage audio files and set schedule play function. It is to realize
audio broadcast activation function.
4.8.5.7.1 File List
Here you can add audio file, or delete audio file. See Figure 4-108.
Figure 4-108
Click Add button, you can add audio file and import the audio file via the local computer.
See Figure 4-109.
249
Figure 4-109
4.8.5.7.2 Schedule
It is to set schedule broadcast function. You can play the different audio files in the
specified periods.
From main menu->Setup->System->Voice->.Schedule, you can see the following
interface. See Figure 4-110.
Figure 4-110
Please refer to the following sheet for detailed information.
Parameter Function
Period There are six periods. Check the box to enable current setup.
250
Parameter Function
Output There are two options: MIC (default)/audio. When reuse the MIC port
port and bidirectional talk port, the bidirectional port has the higher priority.
Please note some series product does not support audio function.
Note
The audio file end time depends on the audio file size and the interval setup.
Priority: Bidirectional talk>Event trigger alarm>Trial listening>Audio schedule
broadcast.
4.8.5.8 Account
Note:
For the character in the following user name or the user group name, system max
supports 6-digits. The space in the front or at the end of the string is null. The valid
string includes: character, number, and underline.
The user amount default setup is 64 and the group amount default setup is 20. The
factory default setup includes two levels: user and admin. You can set the
corresponding group and then set the rights for the respective user in the specified
groups.
User management adopts group/user modes. The user name and the group name
shall be unique. One user shall be included in only one group.
4.8.5.8.1 User name
In this interface you can add/remove user and modify user name. See Figure 4-111.
Figure 4-111
Add user: It is to add a name to group and set the user rights. See Figure 4-112.
There are three default users: admin (password: admin)/888888(password: 888888) and
hidden user “default”.
Hidden user “default” is for system interior use only and can not be deleted. When there is
no login user, hidden user “default” automatically login. You can set some rights such as
monitor for this user so that you can view some channel view without login.
251
Here you can input the user name and password and then select one group for current
user.
Please note the user rights shall not exceed the group right setup.
For convenient setup, please make sure the general user has the lower rights setup than
the admin.
Figure 4-112
Modify user
It is to modify the user property, belonging group, password and rights. See Figure 4-113.
Modify password
It is to modify the user password. You need to input the old password and then input the
new password twice to confirm the new setup. Please click the OK button to save.
Please note, the password ranges from 1-digit to 6-digit. It shall include the number only.
For the user of the account rights, he can modify the password of other users.
252
Figure 4-113
4.8.5.8.2 Group
The group management interface can add/remove group, modify group password and etc.
The interface is shown as in Figure 4-114.
Figure 4-114
Add group: It is to add group and set its corresponding rights. See Figure 4-115.
Please input the group name and then check the box to select the corresponding rights. It
253
includes: shutdown/reboot device, live view, record control, PTZ control and etc.
Figure 4-115
Modify group
Click the modify group button, you can see an interface is shown as in Figure 4-116.
Here you can modify group information such as remarks and rights.
Figure 4-116
254
4.8.5.9 Auto maintain
The auto maintain interface is shown as in Figure 4-117.
Here you can select auto reboot and auto delete old files interval from the dropdown list.
If you want to use the auto delete old files function, you need to set the file period.
Click Manual reboot button, you can restart device manually.
Figure 4-117
4.8.5.10 Import/Export
The interface is shown as in Figure 4-118.
Figure 4-118
Please refer to the following sheet for detailed information.
Parameter Function
Import It is to import the local setup files to the system.
4.8.5.11 Default
The default setup interface is shown as in Figure 4-119.
Here you can select Channel/Network/Event/Storage/System. Or you can check the All
box to select all items.
255
Figure 4-119
4.8.5.12 Upgrade
The upgrade interface is shown as in Figure 4-120.
Please select the upgrade file and then click the update button to begin update. Please
note the file name shall be as *.bin. During the upgrade process, do not unplug the power
cable, network cable, or shutdown the device.
Important
Improper upgrade program may result in device malfunction!
Figure 4-120
.
4.9 Information
4.9.1 Version
The version interface is shown as in Figure 4-121.
Here you can view record channel, alarm input/output information, software version,
release date and etc. Please note the following information is for reference only.
Figure 4-121
256
4.9.2 Log
Here you can view system log. See Figure 4-122.
Figure 4-122
Please refer to the following sheet for log parameter information.
Parameter Function
Type Log types include: system operation, configuration operation, data
operation, event operation, record operation, user management, log
clear.
Start time Set the start time of the requested log.
Search You can select log type from the drop down list and then click search
button to view the list.
You can click the stop button to terminate current search operation.
Detailed You can select one item to view the detailed information.
information
Clear You can click this button to delete all displayed log files. Please
note system does not support clear by type.
Backup You can click this button to backup log files to current PC.
Note
If there is no HDD, system max supports 1024 logs.
If you have connected to the unformatted HDD, system max supports 5000 logs.
If you have connected to the formatted HDD, system max supports 500,000 logs.
System operation logs are saved in system memory. Other types of logs are saved in
the HDD. If there is no HDD, other types of logs are saved in the system memory too.
The logs are safe when you format the HDD. But the logs may become loss once you
removed the HDD.
257
4.9.3 Online User
The online user interface is shown as in Figure 4-123.
Figure 4-123
4.9.4 HDD
The HDD interface is shown as in Figure 4-124. Here you can view HDD information.
Figure 4-124
4.10 Playback
Click Playback button, you can see an interface is shown as in Figure 4-125.
258
Figure 4-125
4.10.1 Search Record
Please set record type, record date, window display mode and channel name.
Select Date
You can click the date on the right pane to select the date. The green highlighted date is
system current date and the blue highlighted date means it has record files.
Window Split
Select window split mode. Click to display in full screen. Click ESC button to exit.
See Figure 4-126.
Figure 4-126
Customized playback
Click , you can see the following interface. See Figure 4-127.
259
Figure 4-127
Now you can select one or more channel(s) and then click to search
record(s).
System supports one or more channels. The window split mode can auto adjust according
to the channel amount. System max supports 16-split.
Select Channel
1~n(n depends on your product channel amount) means main stream and A1~An ((n
depends on your product channel amount)) means sub stream.
Figure 4-128
4.10.2 Fisheye Playback De-Warp
Note
Some series product supports de-warp function.
260
Figure 4-129
4.10.4 Playback
Select a file you want to play and then click Play button, system can begin playback. You
can select to playback in full-screen. Please note for one channel, system can not
playback and download at the same time. You can use the playback control bar to
implement various operations such as play, pause, stop, slow play, fast play and etc.
4.10.5 Download
Select the file(s) you want to download and then click download button, you can see an
interface shown as in Figure 4-130. The Download button becomes Stop button and there
is a process bar for your reference. Please go to you default file saved path to view the
files.
261
Figure 4-130
4.10.6 Load more
It is for you to search record or picture. You can select record channel, record type and
record time to download. Or you can use watermark function to verify file.
4.10.6.1 Download By File
Select channel, record type, bit stream type and then input start time and end time. Click
Search button, the download by file interface is shown as in Figure 4-131.
Figure 4-131
262
Check the file(s) you want to download and there are two options for you to save the
file(s).
Download to local
Click Download to local, system pops up the following interface for you to set record
format and saved path. See Figure 4-132.
Figure 4-132
You can click OK to download and view the download process. After the download
operation, you can see corresponding dialog box.
Download to USB
Connect the corresponding p peripheral device, and then click Download to USB button,
you can see the following interface. See Figure 4-133.
Figure 4-133
Select Backup device and backup type first and then click Start backup button.
After the download operation, you can see corresponding dialogue box.
4.10.6.2 Download by Time
Select channel, bit stream type, start time and end time.
Click Download to Local button, you can see download by time interface is shown as in
Figure 4-134.
263
Figure 4-134
Set record format and saved path, you can click OK to download and view the download
process. After the download operation, you can see corresponding dialog box.
4.10.6.3 Watermark
Watermark interface is shown as In Figure 4-135. Please select a file and then click Verify
button to see the file has been tampered with or not
Figure 4-135
264
Figure 4-136
Please refer to the following sheet for detailed information.
SN Name Function
1 Display It is to display human face detection file list. The latest file is at the
pan top. \
Click Export, you can export the selected file to the USB device.
There are two types: image/record.
Image: Export the recognized human face image.
Record: Export the record file before and after 10 seconds
when the DVR recognizes the human face.
2 Playback Play the searched record file or image. Double click to playback in full
pane screen.
3 Search Set date, start time and end time, click Search button, you can view the
pane corresponding file list.
4.12 Alarm
Click alarm function, you can see an interface is shown as Figure 4-137.
Here you can set device alarm type and alarm sound setup (Please make sure you have
enabled audio function of corresponding alarm events.).
265
Figure 4-137
Please refer to the following sheet for detailed information.
Type Parameter Function
Alarm Video loss System alarms when video loss occurs.
Type Motion detection System alarms when motion detection alarm
occurs.
Tampering System alarms when camera is viciously masking.
Disk full System alarms when disk is full.
Disk error System alarms when disk error occurs.
External alarm Alarm input device sends out alarm.
Operation Prompt Check the box here, system can automatically pops
up an alarm icon on the Alarm button in the main
interface when there is an alarm.
Alarm Play alarm System sends out alarm sound when an alarm
Sound sound occurs. You can specify as you wish.
Sound path Here you can specify alarm sound file.
266
Figure 4-138
Please note, before you un-installation, please close all web pages, otherwise the
un-installation might result in error.
267
5 Professional Surveillance System
Besides Web, you can use our Smart PSS to login the device.
For detailed information, please refer to Smart PSS user’s manual.
268
6 FAQ
1. DVR can not boot up properly.
There are following possibilities:
Input power is not correct.
Power connection is not correct.
Power switch button is damaged.
Program upgrade is wrong.
HDD malfunction or something wrong with HDD ribbon.
Seagate DB35.1,DB35.2,SV35 or Maxtor 17-g has compatibility problem.
Please upgrade to the latest version to solve this problem.
Front panel error.
Main board is damaged.
269
DVR and monitor resistance is not compatible.
Video transmission is too long or degrading is too huge.
DVR color or brightness setup is not correct.
9. There is audio when monitor but there is no audio when system playback.
There are following possibilities:
Setup is not correct. Please enable audio function
Corresponding channel has no video input. Playback is not continuous when the
screen is blue.
270
PTZ decoder setup, connection or installation is not correct.
Cable connection is not correct.
PTZ setup is not correct.
PTZ decoder and DVR protocol is not compatible.
PTZ decoder and DVR address is not compatible.
When there are several decoders, please add 120 Ohm between the PTZ
decoder A/B cables furthest end to delete the reverberation or impedance
matching. Otherwise the PTZ control is not stable.
The distance is too far.
14. There is only mosaic no video when preview or playback video file remotely.
There are following possibilities:
Network fluency is not good.
Client-end resources are limit.
There is multiple-cast group setup in DVR. This mode can result in mosaic.
Usually we do not recommend this mode.
There is privacy mask or channel protection setup.
Current user has no right to monitor.
DVR local video output quality is not good.
271
MAC address conflict.
PC or DVR network card is not good.
272
Camera quality is too low. Lens is dirty. Camera is installed against the light.
Camera aperture setup is not correct.
HDD capacity is not enough.
HDD is damaged.
24. When I login via HTTPS, a dialogue says the certificate for this website is for
other address.
Please follow chapter 4.8.2.16.1 to create server certificate.
25. When I login via HTTPS, a dialogue says the certificate is not trusted.
Please follow chapter 4.8.2.16.2 to download root certificate.
26. When I login via HTTPS, a dialogue says the certificate has expired or is not
valid yet.
Please make sure your PC time is the same as the device time.
27. I connect the general analog camera to the device, there is no video output.
There are following possibilities:
Check camera power supplying, data cable connection and etc.
This series device does not support the analog camera of all brands. Please
make sure the device supports general standard definition analog camera.
28. I connect the standard definition analog camera or the HDCVI camera to the
device, there is no video output.
There are following possibilities:
Check camera power supplying, or camera data cable connection.
For the product supports analog standard definition camera/HD camera, you
need to go to the main menu->Setting->Camera->Channel type to select
corresponding channel type and then restart the DVR.
273
There are following possibilities:
Check the camera is online or not.
Check IP channel setup is right or not (such as IP address, user name, password,
connection protocol, port number.).
The camera has set the whitelist (Only the specified devices can connect to the
camera).
30. After I connected to the IP channel, there one-window output is OK, but there is
no multiple-window output.
There are following possibilities:
Check the sub stream of the camera has been enabled or not.
Check the sub stream type of the camera is H.264 or not.
Check the device supports camera sub stream resolution or not (such as 960H,
D1, HD1 and etc.).
31. After I connected to the IP channel, there multiple-window output is OK, but
there is no one-window output.
There are following possibilities:
Check there is video from the IP channel or not. Please go to the main
menu->info->System->BPS to view bit stream real-time information.
Check the main stream of the camera has been enabled or not.
Check the main stream type of the camera is H.264 or not.
Check the device supports camera main stream resolution or not (such as 960H,
D1, HD1 and etc.).
Check camera network transmission has reached the threshold or not. Please
check the online user of the camera.
32. After I connected to the IP channel, there is no video output in the one-window
or the multiple-window mode. But I can see there is bit stream.
There are following possibilities:
Check the main stream/sub stream type of the camera is H.264 or not.
Check the device supports camera main stream/sub stream resolution or not
(such as 1080P, 720P, 960H, D1, HD1 and etc.).
Check the camera setup. Please make sure It supports the products of other
manufacturers.
33. DDNS registration failed or can not access the device domain name.
There are following possibilities:
Check the device is connected to the WAN. Please check the device has got the
IP address if the PPPoE can dial. If there is a router, please check the router to
make sure the device IP is online.
Check the corresponding protocol of the DDNS is enabled. Check the DDNS
function is OK or not.
274
Check DNS setup is right or not. Default Google DNS server is 8.8.8.8, 8.8.5.5.
You can use different DNS provided by your ISP.
34. I can not use the P2P function on my cell phone or the WEB.
There are following possibilities:
Check the device P2P function is enabled or not. (Main
menu->Setting->Network->P2P)
Check the device is in the WAN or not.
Check cell phone P2P login mode is right or not.
It is the specified device P2P login port or not when you are using P2P client.
Check user name or password is right or not.
Check P2P SN is right or not. You can use the cell phone to scan the QR code on
the device P2P interface (Main menu->Setting->Network->P2P), or you can use
the version information of the WEB to confirm. (For some previous series
products, the device SN is the main board SN, it may result in error.)
35. I connect the standard definition camera to the device, there is no video output.
There are following possibilities:
Check the DVR supports standard definition signal or not. Only some series
product supports analog standard definition signal, HDCVI signal input.
Check channel type is right or not. For the product supports analog standard
definition camera/HD camera, you need to go to the main
menu->Setting->Camera->Channel type to select corresponding channel type
(such as analog) and then restart the DVR. In this way, the DVR can recognize
the analog standard definition.
Check camera power supplying, or camera data cable connection.
Daily Maintenance
275
Please use the brush to clean the board, socket connector and the chassis regularly.
The device shall be soundly earthed in case there is audio/video disturbance. Keep
the device away from the static voltage or induced voltage.
Please unplug the power cable before you remove the audio/video signal cable,
RS232 or RS485 cable.
Do not connect the TV to the local video output port (VOUT).It may result in video
output circuit.
Always shut down the device properly. Please use the shutdown function in the menu,
or you can press the power button in the front panel for at least three seconds to shut
down the device. Otherwise it may result in HDD malfunction.
Please make sure the device is away from the direct sunlight or other heating sources.
Please keep the sound ventilation.
Please check and maintain the device regularly.
276
Appendix A HDD Capacity Calculation
Calculate total capacity needed by each DVR according to video recording (video
recording type and video file storage time).
Step 1: According to Formula (1) to calculate storage capacity qi that is the capacity of
Step 2: After video time requirement is confirmed, according to Formula (2) to calculate
the storage capacity mi , which is storage of each channel needed unit Mbyte.
mi = qi × hi × Di (2)
In the formula:
kept
needed for all channels in the DVR during scheduled video recording.
c
qT mi (3)
i 1
needed for all channels in DVR during alarm video recording (including motion
detection).
c
qT mi ×a% (4)
i 1
277
448K 196M 512K 225M
640K 281M 768K 337M
896K 393M 1024K 450M
1280K 562M 1536K 675M
1792K 787M 2048K 900M
278
Appendix B Compatible backup devices
Appendix B-1 Compatible USB list
Manu factor Model Capacity
Sandisk Cruzer Micro 512M
Sandisk Cruzer Micro 1G
Sandisk Cruzer Micro 2G
Sandisk Cruzer Freedom 256M
Sandisk Cruzer Freedom 512M
Sandisk Cruzer Freedom 1G
Sandisk Cruzer Freedom 2G
Kingston DataTraveler Ⅱ 1G
Kingston DataTraveler Ⅱ 2G
Kingston DataTraveler 1G
Kingston DataTraveler 2G
Maxell USB Flash Stick 128M
Maxell USB Flash Stick 256M
Maxell USB Flash Stick 512M
Maxell USB Flash Stick 1G
Maxell USB Flash Stick 2G
Kingax Super Stick 128M
Kingax Super Stick 256M
Kingax Super Stick 512M
Kingax Super Stick 1G
Kingax Super Stick 2G
Netac U210 128M
Netac U210 256M
Netac U210 512M
Netac U210 1G
Netac U210 2G
Netac U208 4G
Teclast Ti Cool 128M
Teclast Ti Cool 256M
Teclast Ti Cool 512M
Teclast Ti Cool 1G
SanDisk cruzer mirco 2G
SanDisk cruzer mirco 8G
SanDisk Ti Cool 2G
SanDisk Hongjiao 4G
Lexar Lexar 256MB
Kingston Data Traveler 1G
Kingston Data Traveler 16GB
279
Kingston Data Traveler 32GB
Aigo L8315 16GB
Sandisk 250 16GB
Kingston Data Traveler Locker+ 32GB
Netac U228 8GB
280
Samsung TS-H653 Ver.F
Samsung SH-224BB/CHXH
SONY DRU-V200S
SONY DRU-845S
SONY AW-G170S
Pioneer DVR-217CH
281
Seagate Seagate Pipeline HD2 ST31000322CS 1T SATA
Seagate Seagate Pipeline HD2 ST1000VM002 1T SATA
Seagate Seagate Pipeline HD2 ST1500VM002 1T SATA
Seagate Seagate Pipeline HD2 ST2000VM002 2T SATA
Seagate Seagate Pipeline HD2 ST2000VM003 2T SATA
Seagate Seagate Constellation ST3500514NS 500G SATA
ES
Seagate Seagate Constellation ST31000524NS 1T SATA
ES
Seagate Seagate Constellation ST32000644NS 2T SATA
ES
Seagate Seagate Constellation ST2000NM0011 2T SATA
ES
Seagate Seagate Constellation ST1000NM0011 1T SATA
ES
Seagate Seagate Constellation ST500NM0011 500G SATA
ES
Seagate Seagate Constellation ST2000NM0031 2T SATA
ES
Seagate Seagate Constellation ST1000NM0031 1T SATA
ES
Seagate Seagate Constellation ST500NM0031 500G SATA
ES
Seagate Seagate Constellation ST2000NM0051 2T SATA
ES
Seagate Seagate Constellation ST1000NM0051 1T SATA
ES
Seagate Seagate Constellation ST500NM0051 500G SATA
ES
Seagate Seagate Constellation ST33000650NS 3T SATA
ES.2
Seagate Seagate Constellation ST32000645NS 2T SATA
ES.2
Seagate Seagate Constellation ST33000651NS 3T SATA
ES.2
Seagate Seagate Constellation ST32000646NS 2T SATA
ES.2
Seagate Seagate Constellation ST33000652NS 3T SATA
ES.2
Seagate Seagate Constellation ST32000647NS 2T SATA
ES.2
Westem Digital Cariar SE WD3200JD 320G SATA
Westem Digital Cariar SE WD3000JD 300G SATA
282
Westem Digital Cariar SE WD2500JS 250G SATA
Westem Digital Cariar SE16 WD7500KS 750G SATA
Westem Digital Cariar SE16 WD5000KS 500G SATA
Westem Digital Cariar SE16 WD4000KD 400G SATA
Westem Digital Cariar SE16 WD3200KS 320G SATA
Westem Digital Cariar SE16 WD2500KS 250G SATA
Westem Digital WD Caviar SE16 WD2500YS-01SHB0 250G SATA
Westem Digital WD Caviar RE16 WD3200YS-01PGB0 320G SATA
Westem Digital WD Caviar RE2 WD5000YS-01MPB0 500G SATA
Westem Digital WD AV—AVJS WD2500AVJS-63WDA0 500G SATA
Westem Digital WD AV—AVJS WD3200AVJS-63WDA0 320G SATA
Westem Digital WD AV—AVJS WD5000AVJS-63YJA0 500G SATA
Westem Digital WDAV-GP—AVCS WD5000AVCS-63H1B1 500G SATA
Westem Digital WDAV-GP—AVCS WD7500AVCS-63ZLB0 750G SATA
Westem Digital WDAV-GP—AVCS WD3200AVCS 320G SATA
Westem Digital WDAV-GP—AVCS WD2500AVCS 250G SATA
Westem Digital WDAV-GP—EVCS WD10EVCS-63ZLB0 1T SATA
Westem Digital WDAV-GP—EVCS WD20EVCS-63ZLB0 2T SATA
Westem Digital WDAV-GP—AVVS WD3200AVVS-63L2B0 320G SATA
Westem Digital WDAV-GP—AVVS WD5000AVVS-63ZWB0 500G SATA
Westem Digital WDAV-GP—AVVS WD7500AVVS-63E1B1 750G SATA
Westem Digital WDAV-GP—AVVS WD7500AVVS-63E1B1 750G SATA
Westem Digital WDAV-GP—EVVS WD10EVVS-63E1B1 1T SATA
Westem Digital WDAV-GP—EVDS WD10EVDS-63N5B1 1T SATA
Westem Digital WDAV-GP—EVDS WD15EVDS-63V9B0 1.5T SATA
Westem Digital WDAV-GP—EVDS WD20EVDS-63T3B0 2T SATA
Westem Digital WDAV-GP—AVDS WD5000AVDS-63U7B0 500G SATA
Westem Digital WD AV-GP WD30EURS 3T SATA
Westem Digital WD AV-GP WD25EURS 2.5T SATA
Westem Digital WD AV-GP WD20EURS 2T SATA
Westem Digital WD AV-GP WD15EURS 1.5T SATA
Westem Digital WD AV-GP WD10EURS 1T SATA
Westem Digital WD AV-GP WD10EURX 1T SATA
Westem Digital WD AV-GP WD7500AURS 750G SATA
Westem Digital WD AV-GP WD7500AVDS 500G SATA
Westem Digital WD AV-GP WD500AVDS 500G SATA
Westem Digital WD AV-GP WD10EUCX 1T SATA
Samsung Samsung—HA HA500LJ/CE 500G SATA
Samsung Samsung—HA HA751LJ 750G SATA
Samsung Samsung—HA HA101UJ/CE 1T SATA
Samsung Samsung—HD HD502HI/CEC 500G SATA
Samsung Samsung—HD HD103SI/CEC 1T SATA
Samsung Samsung—HD HD154UI/CE 1.5T SATA
283
Hitachi HitachiCinemaStar™ HCP725050GLA380 500G SATA
5K500
Hitachi HitachiCinemaStar™ HCT721050SLA360 500G SATA
7K1000.B
Hitachi HitachiCinemaStar™ HCT721075SLA360 750G SATA
7K1000.B
Hitachi HitachiCinemaStar™ HCT721010SLA360 1T SATA
7K1000.B
Maxtor DiamondMax 20 STM3320820AS 320G SATA
Maxtor DiamondMax 20 STM3250820AS 250G SATA
284
Appendix C Compatible CD/DVD Burner List
NOTE: Please upgrade the DVR firmware to latest version to ensure the accuracy of the
table below. And you can use the USB cable with the model recommended to set USB
burner.
Manufacturer Model Port Type Type
Sony DRX-S50U USB DVD-RW
Sony DRX-S70U USB DVD-RW
Sony AW-G170S SATA DVD-RW
Samsung TS-H653A SATA DVD-RW
Panasonic SW-9588-C SATA DVD-RW
Sony DRX-S50U USB DVD-RW
BenQ 5232WI USB DVD-RW
285
Appendix D Compatible Displayer List
Please refer to the following sheet form compatible displayer list.
Brand Model Dimension (Unit: inch)
BENQ(LCD) ET-0007-TA 19-inch (wide screen)
DELL(LCD) E178FPc 17-inch
BENQ(LCD) Q7T4 17-inch
BENQ(LCD) Q7T3 17-inch
HFNOVO(LCD) LXB-L17C 17-inch
SANGSUNG(LCD) 225BW 22 寸(wide screen)
HFNOVO(CRT) LXB-FD17069HB 17 -inch
HFNOVO(CRT) LXB-HF769A 17-inch
HFNOVO(CRT) LX-GJ556D 17-inch
Samsung (LCD) 2494HS 24-inch
Samsung (LCD) P2350 23-inch
Samsung (LCD) P2250 22-inch
Samsung (LCD) P2370G 23-inch
Samsung (LCD) 2043 20-inch
Samsung (LCD) 2243EW 22-inch
Samsung (LCD) SMT-1922P 19-inch
Samsung (LCD) T190 19-inch
Samsung (LCD) T240 24-inch
LG (LCD) W1942SP 19-inch
LG (LCD) W2243S 22-inch
LG (LCD) W2343T 23-inch
BENQ (LCD) G900HD 18.5-inch
BENQ(LCD) G2220HD 22-inch
PHILIPS (LCD) 230E 23-inch
PHILIPS (LCD) 220CW9 23-inch
PHILIPS (LCD) 220BW9 24-inch
PHILIPS (LCD) 220EW9 25-inch
286
Appendix E Compatible Switcher
Brand Model network working mode
D-LinK DES-1016D 10/100M self-adaptive
D-LinK DES-1008D 10/100M self-adaptive
Five network modes
1. AUTO
2. HALF-10M
Ruijie RG-S1926S
3. FULL-10M
4 .HALF-100M
5. FULL-100M
H3C H3C-S1024 10/100M self-adaptive
TP-LINK TL-SF1016 10/100M self-adaptive
TP-LINK TL-SF1008+ 10/100M self-adaptive
287
Appendix F Compatible Wireless Mouse List
Please refer to the following sheet for compatible SD card brand.
Brand Model
V80
Rapoo 3500
Logitech M215
Shuangfeiyan Tianyao G7-630
288
Appendix G Earthing
1. What is the surge?
Surge is a short current or voltage change during a very short time. In the circuit, it lasts
for microsecond. In a 220V circuit, the 5KV or 10KV voltage change during a very short
time (about microseconds) can be called a surge. The surge comes from two ways:
external surge and internal surge.
The external surge: The external surge mainly comes from the thunder lightning. Or it
comes from the voltage change during the on/off operation in the electric power
cable.
The internal surge: The research finds 88% of the surge from the low voltage comes
from the internal of the building such as the air conditioning, elevator, electric welding,
air compressor, water pump, power button, duplicating machine and other device of
inductive load.
The lightning surge is far above the load level the PC or the micro devices can support. In
most cases, the surge can result in electric device chip damage, PC error code,
accelerating the part aging, data loss and etc. Even when a small 20 horsepower inductive
engine boots up or stops, the surge can reach 3000V to 50000V, which can adversely
affect the electronic devices that use the same distribution box.
To protect the device, you need to evaluate its environment, the lighting affection degree
objectively. Because surge has close relationship with the voltage amplitude, frequency,
network structure, device voltage-resistance, protection level, ground and etc. The
thunder proof work shall be a systematic project, emphasizing the all-round protection
(including building, transmission cable, device, ground and etc.). There shall be
comprehensive management and the measures shall be scientific, reliable, practical and
economic. Considering the high voltage during the inductive thundering, the International
Electrotechnical Committee (IEC) standard on the energy absorbing step by step theory
and magnitude classification in the protection zone, you need to prepare multiple
precaution levels.
You can use the lightning rod, lightning strap or the lightning net to reduce the damage to
the building, personal injury or the property,
289
Signal lightning arrester: This device is mainly used in the PC network,
communication system. The connection type is serial connection. Once you
connected the signal lightning arrestor with the signal port, it can cut the channel of
the thunderstorm to the device, and on the other hand, it can discharge the current to
the ground to guarantee the device proper work. The signal lightning arrester has
many specifications, and widely used in many devices such as telephone, network,
analog communication, digital communication, cable TV and satellite antenna. For all
the input port, especially those from the outdoor, you need to install the signal
lightning arrester.
Antenna feed cable lightning arrester: It is suitable for antenna system of the
transmitter or the device system to receive the wireless signal. It uses the serial
connection too.
Please note, when you select the lighting arrester, please pay attention to the port type
and the earthing reliability. In some important environment, you need to use special
shielded cable. Do not parallel connect the thunder proof ground cable with the ground
cable of the lightning rod. Please make sure they are far enough and grounded
respectively.
One-point ground: In the following figure you can see there is a one-point ground. This
connection provides common port to allow signal to be transmitted in many circuits. If
there is no common port, the error signal transmission occurred. In the one-point ground
mode, each circuit is just grounded only and they are connected at the same port. Since
there is only one common port, there is no circuit and so, there is no interference.
Multiple-point ground: In the following figure, you can see the internal circuit uses the
chassis as the common point. While at the same time, all devices chassis use the
earthing as the common port. In this connection, the ground structure can provide the
lower ground resistance because when there are multiple-point grounds; each ground
cable is as short as possible. And the parallel cable connection can reduce the total
290
conductance of the ground conductor. In the high-frequency circuit, you need to use the
multiple-point ground mode and each cable needs to connect to the ground. The length
shall be less than the 1/20 of the signal wavelength.
Mixed ground: The mix ground consists of the feature of the one-point ground and
multiple-point ground. For example, the power in the system needs to use the one-point
ground mode while the radio frequency signal requires the multiple-point ground. So,
you can use the following figure to earth. For the direct current (DC), the capacitance is
open circuit and the circuit is one-point ground. For the radio frequency signal, the
capacitance is conducive and the circuit adopts multiple-point ground.
When connecting devices of huge size (the device physical dimension and connection
cable is big comparing with the wave path of existed interference), then there are
possibility of interference when the current goes through the chassis and cable. In this
situation, the interference circuit path usually lies in the system ground circuit.
When considering the earthing, you need to think about two aspects: The first is the
system compatibility, and the other is the external interference coupling into the earth
circuit, which results in system error. For the external interference is not regular, it is not
easy to resolve.
291
The thunder proof ground shall adopt the special ground cable from the monitor
control room to the ground object. The ground cable adopts copper insulation cable
or wire and its ground section shall be more than 20mm2.
The ground cable of the monitor system can not short circuit or mixed connected with
the strong alternative current cable.
For all the ground cables from the control room to the monitor system or ground cable
of other monitor devices, please use the copper resistance soft cable and its section
shall be more than 4mm2.
The monitor system usually can adopt the one-point ground.
Please connect the ground end of 3-pin socket in the monitor system to the ground
port of the system (protection ground cable)
4. The shortcut way to check the electric system using the digital multimeter
For 220V AC socket, from the top to the bottom, E (ground cable), N (neutral cable), L(live
cable). Please refer to the following figure.
There is a shortcut way to check these thee cables connection are standard or not (not the
accurate check).
Importance
In the following operations, the multimeter range shall be at 750V!
292
For L (live cable)
Turn the digital multimeter to 750V AC, use your one hand to hold the metal end, and then
the other hand insert the pen to the L port of the socket. See the following figure. If the
multimeter shows 120, then you can see current live cable connection is standard. If the
value is less than 60, then you can see current live cable connection is not proper or it is
not the live cable at all.
293
Note:
This manual is for reference only. Slight difference may be found in the user
interface.
All the designs and software here are subject to change without prior written
notice.
All trademarks and registered trademarks mentioned are the properties of their
respective owners.
If there is any uncertainty or controversy, please refer to the final explanation of
us.
Please visit our website or contact your local retailer for more information.
294