DNVR Digital Network Video Recorder : Before Using This System, Please Read The User Manual Carefully
DNVR Digital Network Video Recorder : Before Using This System, Please Read The User Manual Carefully
DNVR Digital Network Video Recorder : Before Using This System, Please Read The User Manual Carefully
USER MANUAL
108Q9/216Q9
carefully.
1
Attention:
*Don’t use the system at place with high humility or dust or dirty.
*Avoid direct sunshine or being heated.
*Leave the system away from magnetism objects.
*Avoid high or low temperature(recommended temperature range: 5°C-35°C).
*Close the system before installing the hardware and software.
*Don’t place the system at some place where will likely have a shake.
*Please use it at the aeration place.
*Radio, television or wireless communicate device could cause damage to the
system.
*Don’t dismantle the system by yourself freely.
*Don’t put heavy object on the system.
Table of Content
Attention 2
Chapter 4. Playback 22
2
Chapter 5. Remote view 25
5.1 Remote view by client software 25
5.2 Remote view via IE 27
5.3 Mobile view 28
3
z User can set motion detection for each camera within all the periods of
each week, and the motion detection will activate according to the
schedule;
z Circularly switch function; Can set single channel or multi channels to
switch circularly;
z User-friendly interface, it is easy for user to operate it;
z The system will show hard disk is full if the hard disk will up to the
capability.
z RAM:512MB or above
z Display card: ATI128MB or above,Geforce2 MX400 128MB or
above
z CPU: Celeron D2.8 G or above or Intel P4 2.4 G or above
z Resolution of monitor: 1024*768(32bits color)
z HDD: IDE, SATA,SCSI, 80GB or above
z Motherboard: Intel Chipset 865 or above
Attention: before installing the driver of display card, please install the driver of
motherboard; otherwise it will affect the function of display card and video
surveillance system
4
2.1 Install driver
2.1.1. Insert the CD into CD/DVD-ROM, it will pop up a installation guide
window, shown as below:
Select Installation Driver option, it will pop up the driver installation window:
2.1.2. Click on Install button to install the driver, and it will show: Installing
driver, please wait…
5
2.2 Install Software
2.2.1 Select Installation Server option, it will pop up the DVR server installation
window:
Note: For this software, users also can choose to run the software directly
without installation.
(Copy all the files from CD to PC, and run the DVRInit.exe to initialize, run
DVR.exe to run DVR surveillance system.)
Click on initialize button to begin initial. Please wait a moment, it will indicate
initialize successfully.
6
If you want to delete DDNS account, please tick “Delete DDNS account” option,
then it will delete DDNS account at the same time.
If you want to delete p2p account, please tick “Delete p2p service account”
option, then it will delete p2p account at the same time.
2.2.2 After initialization completely double click on DVR.exe icon, and go to the
DDNS and p2p account application interface. You can apply for a DDNS and a
p2p account in this window.
Input a account name and password then click on apply button to apply. After
completely application, it will show application succeeded information on the
top of the window.
Note: If you do not want to use the DDNS or the p2p, you can pass it without
application by click on Next button directly.
If you want to apply for another DDNS account or p2p account, please initialize
the software first, then apply for another one.
7
2.4 Channel number and draw mode selection
After DDNS and p2p application, click on Next button, it will go to the channel
number and draw mode selection window:
8
1
Playback
System setup Circular Other
Run schedule i
Monitor Capture picture
Note: When the button is selected, it will become red from grey.
2. System setup: click it, user can get following icon to set the preview, record,
alarm, schedule, PTZ, authorization, others as below picture
3. Run schedule: click it, the system will run according to the schedule
4. Playback: playback the recorded files
5. Monitor: Monitor the audio
6. Capture picture: it allows the function of snapshot
9
7. Circular preview: Auto scan for different channels, the default interval time
is five seconds.
8. Other: contains minimize, user management, remote connect information,
disk status.
9. Preview: choose the channel that you want to preview, click the number, it
will change to preview status when the number color change from grey to
green.
10. Record, alarm: choose the channel that you want to record or start alarm
function, click the channel number, it will start to record or start alarm function
when the number color change from grey to green
11. Color: adjust black/white, brightness, saturation according the actual
situation
12. PTZ: click the PTZ, user could adjust the PTZ setting.
3.3 Setup
3.3.1 Local user management
Click “other” button , and get tool list, click “local user
management”, ”user management” window will pop-up. ”user
management” is only for setting authority of server user, it is different from the
“Network user authorization “ (If user want to remote view through IE ,
10
user need to set “Network user authorization “)
Set the authorization first, then click “add”, type the new user name and
password, then press “ok” to save the setting.
11
3.3.3 Preview
Record name: Tick it, while recording, it will show the channel name.
Record time: Tick it, while recording, it will show the system time.
X-axis, Y-axis: Adjust the shown position of the channel name or record time.
Color of time auto brighten: the color will change if record.
Channel name: set the channel name.
Camera ID Position: set the position of the camera ID. Could choose in ”left
top, right top ,left bottom ,right bottom”.
Font: the font of the channel name will be changed if you choose set a font.
Sharpness: The sharpness of record name and record time.
3.3.4 Record
In this part, user can set the video quality for recorded files.
12
CBR: Constant bitrate, select it, the bitrate will not change
VBR: Variable bitrate, select it, the bitrate will change according to actual
situation
Record quality: provide 6 levels of record quality (level 1-6), “best” is
recommended.
Record audio synchronously: record audio while recording video.
Self define video quality: user can define the video quality by himself
Packing interval for recording file: Set the packing interval.
Select storage disk: set the storage location.
Active denoise time range: set the time range to reduce noise, from 18:00 to
8:00 is recommended.
Net trans: set the network transmit quality, provide 5 levels (level 6-11) and
self define transmit frame rate. 5FPS is recommended.
3.3.5 Alarm
13
Basic setup
Video Signal lost: tick it, if any video signal lost, the system will start to record
Motion detection: tick it, if any motion detected, the system will start to
record
Detection level and sensitivity: to adjust the sensitivity of motion detection
(The default level super is the best)
Alarm relay:
Video signal lost alarm sound: tick it, and select an audio file. If alarm is
triggered by video signal lost, you will hear the sound you have selected
Motion detection alarm sound: tick it, and select an audio file. If alarm is
triggered by motion, you will hear the sound you have selected
Post-alarm time: set the post-alarm time.
Post-record time: set the post-record time.
Detection area
14
The default area is the whole area (in the yellow square). User could clear the
current detection area, and set a different area according to request.
Record Relay: It will be take effect when choose some channels to link-act
recording. For example: set 5 channel to test, link-act record channel is
3,4,5.Once some moving objects in choose area of 5 channel ,then 3,4,5
channels will start to record simultaneously .
15
3.3.6 Schedule
16
Enter the start time, end time, and select record type, click “OK” to confirm,
then click on “copy to..” , copy to other days and channels, press “save” to finish
setup.
After finished the setting, go back to the main interface, and Click “run on
schedule” button( ), the button color will change from grey to red, it
indicates the schedule is working.
3.3.7 PTZ
Set PTZ protocol (please confirm with your PTZ camera supplier about the
correct protocol of your camera), the suitable baud rate and address of the PTZ
decode.
3.3.8 Network
17
This option is for network user authorization and trusted IP address.
Trust IP: user could setup accessing IP address, limit accessing IP address by
[add network user][modify IP ] [delete IP], tick the IP address if user don’t want
to limit the IP
Set the proper authorization first, then add or modify the user.
18
3.3.9 Others
This option includes tools which do not list on the toolbar of system setup.
Lock system key: tick it, while running the system, if click on any button of
system, it can not work until unlock the system.
Logon manually: tick it, while click the” dvr.exe”, use has to type user name
and password to logon
Enter windows and auto run: tick it, and set the right windows OS user and
password, the software will auto run after start the PC.
Auto shut down: tick it, and type the interval day and time, the system and
computer will shut down according to the requested time and date
Restart computer: tick it, and type the interval day and time, the system
and computer will restart according to the requested time and date.
Auto run schedule after software started: auto run schedule after DVR
software started.
Mouse auto lock: tick it, and set the time, after the selected time, the mouse
will auto lock.
19
Net trans port: if user allows other user to remote access this server, must
tick it, the default port is 5191.
Web Server port: if user allows other user to remote access this server, must
tick it, the default port is 80.
Remark: If user the default port, while other user remote access the
server, just type the IP address of server, for example:
http://192.168.5.2 . Once user change the default Web Sever port
from 80 to 81, then has to type http://192.168.5.2:81 .
FTP server port: if user allows other user to remote access this server, must
tick it, the default port is 21.
Push warn dialog when disk full: tick it, while the disk is nearly full, it will
have a warn dialog.
DDNS: the secondly domain name in viewnvr.com you applied.
P2P account: the p2p account you applied in software.
Start time: choose the begin time for the adjusted color
End time: choose the finish time for the adjusted color
Edit time: make change for above set time
20
Delete time: delete above start or end time
Clear time: clear above start, end time
Start all: start all the time selected
Close all: close all the time selected
Chapter 4 Playback
Recorded file search and playback is important for surveillance system. This
system adopts video and audio synchronization
Press the playback button from the main interface of software, user will get
following interface:
The number of date is yellow color and with an ellipse: Current date
: To adjust the playback time. Left button is for minute; right
button is for hour.
21
: Snapshot picture when playback
: To adjust volume
Browse the captured picture: click , following window will pop up:
Select the channel that user want to view the captured picture, the
corresponding picture will be listed at the right bottom window. Click the picture
file and open it, user can zoom in or out the picture, or save it on pc, print it.
22
Here you can open a file to play or backup the recorded file.
Burn: click on burn button( ), then it will show the burn window:
23
Here you can burn the recorded file to CD.
With the client program, user can remote view the live picture from server, and,
record, playback the recorded file from server or local PC.
Step 1: Insert the CD into the CD/DVD-ROM, it will pop up the software
installation window, select the Installation client option, click on Install button
to install the client software.
24
In remote view interface, click on system setup button, it will pop up the
following window:
Here you can choose to use the sub-stream or the main-stream to get a better
remote view quality (While using sub-stream, network transmit quality is better;
while using main-stream, image quality is better).
25
5.2 Remote view via IE
Step 1: Run an Internet Explorer browser, Enable all the ActiveX controls and
plug-ins(Refer to the Appendix 3).
Step 2: Type the IP address or DDNS, drag the right scroll bar to the end, and
click the here to download the ActiveX control.
Install it:
26
Then it will show install succeed.
Then refresh the IE browser once, and system will pop-up the login window:
Step 3: Type the IP address or domain name of server, the correct user name
and password, the default user name is: admin; the default password is: 1234.
Then click “ok”, you will get following interface to show that the connecting are
successful.
27
Note: IE remote view need to forward ports in router.
1). Copy the client software dvrclient.exe from WinCE folder to your mobile phone.
2). Open the client software, and the following window will pop-up, then input your server
IP or domain name, and user, key. (Our default port number is 5191) default user and key:
admin, 1234.
3).After successfully login, you will enter into the main window, then choose camera at the
menu (menu on the top left corner) and go to channel selection window.
28
4).Choose the channel that you want to view:
1. Enter into system setup interface, select schedule option, and set the schedule here:
30
5. Tick Enter windows and Auto run option, let it auto login computer’s OS, and run
DVR software.
6. Input username and password, and restart PC to check it.
Note: Here are the windows OS user and password. Please input the right username and password to login
window OS.
1. Monitor the audio in preview interface: Click on the channel’s picture, then click on
monitor button once, it will become red, shown as below:
31
Note: Make sure you can hear the audio while preview.
2. Click system setup button, enter into the system setup interface, then choose Record
Options, select channel name, and tick Record Audio synchronously option.
1. Run an Internet Explorer (IE) browser, click tool menu, and select Internet options…
option:
33
2. Then it will pop up Internet options window:
3. Select Security option, and click Internet icon, and click on Custom Level… button,
then it will pop up the following setting window:
34
Enable all the ActiveX controls and plug-ins here.
4. Then click OK button, and then click Yes button to confirm and save the setting.
1. After entered into the main interface, you will see a PTZ controller area at the bottom of
right corner:
35
Click on the dome button( ), pre-set setting window will pop up, shown as on the
right above.
2. Choose your channel and pre-position, adjust the camera to the requested direction,
then click on setup button to set this position to pre-position:
3. After clicked the setup button, it will pop up a prompt dialogue to set a title for this
pre-position, like following picture.
36
4. Enter the name by clicking the up, down, left, right button of the PTZ controller (use up,
down buttons to select the number or letter, use left, right buttons to set the direction), and
37