HengTong DVR2000 User Manual PDF

User Manual
04-08-2004
.1.
User Manual for HengTong DVR2000

Catalogue
Things Inventory
Specification of Product
1. Introduction
1.1 Summarize
1.2 Standard Functions
1.3 System Requirement
2. Enable the System

2.1 Open the Power
2.2 Loading
3. Utility
3.1 Camera Setting
3.2 Housekeeping
3.2.1 Data Backup
3.2.2 Remove Record
3.2.3 Disk Manage
3.3 Record Setting

3.3.1 Workday
3.3.2 Weekend
3.3.3 Alarm
3.4 Option Setting

3.4.1 Display
3.4.2 Recording
3.4.3 Operation Setting
3.4.4 Audio Setting
3.4.5 Password
3.4.6 Other
3.5 System Information
3.6 Motion Detection of Video

3.6.1 Motion Detection Setting
3.6.2 Set the Areas for Detecting
3.6.3 Set the Sensitivity of The Motion Detection
3.6.4 Enable the Motion Detection’S Function
.2.

4.Playback
4.1 Playback
4.2 Remote/ Local

4.2.1 Local Playback
4.2.2 Remote Playback
4.3 Multi-Channel Playback
4.4 Frame Processing
4.5 Functional Key for Playback
5. DVR Configuration
5.1 Logon
5.2 Channel Distribution (Used for the Boards with the Video Expanding
Functions such as 8R16D、8R32D、H128D)
5.3 Alarm Alert
5.4 Alarm File Overwrite
5.5 Configuration Backup and Restore
5.6 Pan/ Tilt/ Zoom control
5.7 Pan/ Tilt/ Zoom
5.8 Select Driver to Record
5.9 Time Stamp Setup
5.10 Video Server User Manager
5.11 Add User
5.12 Access Limitation
5.13 Network Bandwidth
5.14 Watchdog Setting
5.15 Time Open /Close /Reboot Computer
5.16 Property of Media Player
5.17 Video Revolve
5.18 Select “PAL” Or “NTSC”
6.Tool Bar Function

6.1 Zoom In, Zoom Out, Restore
6.2 Channel Switch
6.3 Take Photograph
6.4 Manage the Picture
6.5 Listening
6.6 Volume Set
6.7 Quality Set of Image
6.8 Log
6.9 Image Shelter
6.10 Desktop
6.11 Swift Key of DVR Configuration
.3.

6.12 Others
6.13 Help
6.14 PTZ Control

6.14.1 Select Camera
6.14.2 Control Speed
6.14.3 Control PTZ’s Focus
6.14.4 Pre-Position
7 Alarm I/O Connection

7.1 External View of Connectors
7.2 Alarm Output Configurations:
7.3 Alarm Connection Wiring Diagram
7.4 Alarm Connector of D Type
8. Decoder’s Instruction
8.1 Device Summarize
8.2 Device Introduction
8.3 Connection Sketch Map
8.4 Device Function Switch, Connection Sketch Map
8.5 Technique Guild Line
9.Single-Channel Remote
9.1 Connect Server
9.2 Setup The Server Mode

9.2.1 Add Server
9.2.2 Modify, Delete Server
9.3 Logon Server

9.3.1 Logon Server
9.3.2 Logon Server Directly
9.4 Remote Setting

9.4.1 Select Camera
9.4.2 Remote Record, Playback
9.4.3 Adjust Surveillance Resolution
9.4.4 Adjust Compression Ratio
9.4.5 Patrolling Setting
9.5 Remote Control

9.5.1 Logon Password
9.5.2 Display Control
9.5.3 Audio Control
9.5.4 Full Screen Display
9.5.5 Remote Control
9.5.6 Cut Connection/ Close Window
.4.

9.6 Remote Playback
9.7 Remote Alarm Receiver
9.8 Remote PTZ Control
10. Installation of Boards

10.1 Installation of Software Compression Boards
10.2 Installation of Hardware Compression Board
11. Install the Driver

11.1 Install the Hengtong DVR2000 Video Cards Driver Under the WIN98SE
Operation System.
11.2 Install Hengtong DVR2000 Video Cards Driver Under WIN2000.
11. 3 Install Hengtong DVR2000 Video Cards Driver Under WINXP.
12. Install the Internet Application
13.Common Trouble and Solution

13.1 Frequently Halt
13.2 Display Incapability
13.3 Circulation is Unable
13.4 Catalogue Establishing Failed.
13.5 Invalid Operation
13.6 Time Lack when Recording
13.7 Distort Alarm
13.8 Alarm All the Times
13.9 Splash or Blank Screen During Hardware Compression’S Playback Process
13.10 Abnormally Display
13.11 The Image is Indistinct
Things Inventory
Please assure the package of DVR2000 Series If it has been destroyed, or has
been hard up of any fittings; please contact your dealer as soon as possible.
1. One mouse with PS/2 connection;
2. One keyboard;
3. One power string of equipments;
4. One key for recorder control door;
5. Corresponding CD;
6. One users’ manual;
7. One certificate of competency;
.5.

8. One guarantee of quality;
9. One backup key for hard disk;
10. One pair of sound boxes;
11. One PS/2 line;
12. All kinds of matched CD;
Specification of Product
1. Power electronic power of 250W, input with 220VAC, 50 Hz;
the load minimum is +5V@4A, +12V@1.2A；
MTBF 25000 hours;
2.the cooling fans the cooling fans of 120CFM (with filtrated netting)
3.size install with 19’’ shelf height 4U;
482(W) x177 (H) x478 (D) mm
or 482（W）x200（H）x500（D ）
4.weight 25kg(38.5 lb)；
5.the work
Temperature 0~50 degrees Centigrade;
6.the keyboard
Interface PS/2 port
7. The mouse
Interface PS/2 port
1. Introduction
1.1 Summarize
HengTong DVR2000 adopt MPEG-4 compression mode. It has been designed to

be flexible that can connect with different video cameras and display different
camera images in real time. Notwithstanding the different inputs and display, all
models will have the same features which are kept as uniform throughout the
series.
1.2 Standard Functions
Digital surveillance recorder and multi-menu processor
Support up to 128 camera input with multi display modes;
Support PAL and NTSC form
.6.

Amity user graphic interface
Can realize up to 32 channels video real- time displaying and recording

under the optimum condition
Real time digital Video compression
Can carry on the operation of multiple tasks at the same time,
Have multi search mode on playback function;
Prevent the video video from being distorted
Alarm triggered recording
Alarm I/O interface
Pre-alarm recording
Can change calculagraph to set the recording time.
Motion detection alarm recording
Easy to expand by software upgrade and system integration
Support multilingual capability
Doing alternate on-line visit and playback though dialing-up, LAN.

1.3 System Requirement
Available OS: Windows98/2000/XP/WinNT
Recommended setting: CPU: greater than Intel PⅢ, above 1GHZ.
CPU for soft compression : recommend Intel PⅥ ,above 2GHZ
EMS memory: 256M
Graphics adapter: graphics memory above 32M.
Power: recommend using ATX power, 350W
Note: recommend using mail board of INTEL chips group.
.7.

2. Enable the System
2.1 Open the Power
Please correctly select the voltage for inputting the power firstly. And then press the
power switch on the front panel of the host to enable the system.
Main interface as Figure 2-1
There are some control button such as display and record control panel and
“Utility” on the right hand.
On the bottom, a progress bar shows the current date, time, user and the present
of disk’s occupied room.
It shows the brand of system, type of host and copyright NO in the upper left
corner.
The auto switch of single channel button and multi channel button are in upper
right corner.
2.2 Loading
After enable the system, it will show the main interface.
Click the Logon button; it will pop up a Logon dialog box

Two default usernames are available: “SUPER” and “OPERATOR”
The factory default password is NULL for either case.
When you logon as “SUPER”, please click the Utility button to change the logon
password (we will concretely explain it on “System Operation Data” section).
However, if you logon as “OPERATOR”, the “Utility”, “playback” and some other
buttons will be disabled to prevent the password and recording settings from
being modified.
Figure 2-2
.8.
3. Utility
Utility means all kinds of setting operation for DVR2000 is in here. You can select
any setting to do by your need.
Figure 3-1
3.1 Camera Setting
The users can define the name of every channel through camera setting. After
setting, the name will be showed on the top of the video. It is facilitate for users to
select the camera when playback.
After setting, click “OK” to return. As following picture:
Note:
A. The character “\ /: *? “ < > |” can’t be included in the name.
B. If there are more than 16 channels in the system. When you want to name the
19-channel for example, please pop up “17-32”channels’ button, and then click
the 19th to rename.
Figure 3-2
.9.
3.2 Housekeeping
Housekeeping is a button to be clicked to set the according management for system’s

data. You can backup and delete the data, scan, clean up and format the disk from there.
3.2.1 Data Backup
Data backup means backup the record data to mobile disk or recording the data to CD,
etc. as following:
Figure 3-3
.10.
You can disposal all the record information through data backup. Firstly, please select
the camera by clicking the left box to be “√”, and then click “start” to finish.
If you wonder whether the selected camera is right or not, you can display the selected
camera through “preview” button.
3.2.2 Remove Record
Remove record means deleting some useless record. In this case, it will save a lot of
disk room. Select the record file by clicking it to “√”, and then press “start” button to
delete.
Figure 3-4
3.2.3 Disk Manage

Some maintenance process such as the disk scanning, scrap managing, formatting are
through disk manage. The operation is the same as WINDOWS’. As figure:
.11.
3.3 Record Setting
You can set the concrete time slice for recording, status of alarm recording and instant
state through this record setting dialog box.
3.3.1 Workday
Workday means some day from Mon. to Friday. There are two time slices in the workday
option. It means that the timing video can be divided into two stages during one day.
According to the habit of business, it can be divided into morning and afternoon. It does
not record at noon. In order to avoid missing the important events, you can set motion
detection recording mode or alarm recording. In this case, it wouldn’t miss the important
video record, and also save the disk room. Please see the picture following:
Figure 3-5
.12.
Select the camera at first, and then input the begin time and end time for
recording. If you want to set the second time slice, please lick “ second time slice”,
make it fall into and go down, and then set the time as above.
You can adjust the frame ration by changing the value on the “f/s” box. Less frame
ratio, less the disk room it occupied. The default value is 25fps.
In the image quality column, you can choose “CIF” or “D1” to record by your need.
The difference between them lies in the size of the video file and the resolution ratio.
The file from “D1” is bigger, and the resolution of “D1” is higher.
Note:
The resolution: CIF：PAL 352x288，NTSC 320x240
D1： PAL 704x576，NTSC 704x480
After you setting the parameter of the first camera, and then click “ Apply all”, all
the other cameras will be automatically set to be the same parameters as the first
one.
Exit by click “OK” after finishing setup.
3.3.2 Weekend
Weekend means Saturday and Sunday. The user can set the timing record mode
according to the actual need. The operation is the same as “workday” part. As figure:
Figure 3-6
3.3.3 Alarm
.13.
You can set the functions of alarm recording in the “alarm” column. There are two record
modes. One is alarm recording that is sprung by the signal from the peripheral
equipment; the other is motion detection recording mode.
In “ open (second)” column, you can set the second for continuing to record after the
alarm signal is ended.
Click “√” on the “Nopen” column to enable the constant opening. Cancel “√” to enable the
constant closing.
Note: “Nopen” means it will spring the alarm when it received the signal that the
input port has been closed.
You can change the frame ratio for alarm recording in “f/s” column.
Select CIF or D1 on the image quality column.
“Pre-record” means the system will record in advance before the alarm has been sprang.
You can set seconds when the system processes the pre-record. For example, if you set
3 sec, the system will start recording before 3 seconds when the alarm is sprang.
“ Arm/disarm port” can show the arm/disarm state of alarm host. If the “open” box has
been selected to be“√” , the system will automatically send the alarm signal and
corresponding image to the remote clients in arm status.(Have installed HengTong
DVR2000 remote software). It will process local alarm instead of sending the record to
the remote clients in disarm status.
Note: if port of certain camera has been defined, the alarm recording functions of
this channel will become invalid.
Figure 3-6
.14.
“Scheduled Alarm” is used to set the time slice for alarm recording. The
operation steps are the same as the ones of timing record. Select the camera by
click “√” firstly, and then input the time slice; finally, click “OK” to exit.
Figure 3-7
.15.
3.4 Option Setting
3.4.1 Display
In display option, the users not only can set the interval for automatically switching each
of the single image or multi images, but also can select the camera you want to do switch.
“Dwell time” means the switch interval for two cameras. The default value is “2”. Users
can change the value by need.
“Sequencing,” means the order of the camera that will be switched over. Active the
camera with “√” to do switch.
Figure 3-8
.16.
3.4.2 Recording
Users can select the suitable recording mode from the recording column as figure 3-9
according to their need
“Linear” means that it cannot circularly record after HDD full. After the system shows the
massage about “disk is full”, user need to delete some of the record files or replace the
hard disk with a new one to continue recording.
“ Circular” means it can circularly record by automatically covering the foregoing files
after HDD full. It needn’t to exchange a new hard disk.
After setting, please click “OK” to exit.

Please view the following figure:
Figure 3-9
.17.
3.4.3 Operation Setting
“Status retain” means it will return to the original state without taking to set up
again after the system halted or reboot.
“Auto start” means the users can be landed with the user name that is
established before.
other settings just need users to click “√” to select. After setting, click “OK” to exit. As
following (PTZ is pan/tilt zoom controlling)
Figure 3-10
3.4.4 Audio Setting
If you want to enable the audio recording function and realize the audio remote delivery,
Please select the corresponding camera NO. As figure 3-11
Figure 3-11
.18.
3.4.5 Password
You can set multi-lever users and password in this Order column, and also can limited
the new users’ authority. As following figure:
Figure 3-12
Click “ Add” to add a new user, input the new username and password in the
pop-up dialog box, and click “OK” to finish. For example, add “cana” as following:
Figure 3-13
.19.
After adding a new user, you need to setup the authority for him according to
the actual need. Firstly, select the username you want to set authority from the
left box, and then click the “popedom ” button. Select the authority in the dialog
box. After setting, click “OK” to exit. As following:
Figure 3-14
3.4.6 Other
There are a lot of great settings in the “other” column. Such as setting for time stamp
position, setting log size, setting for video losing, etc.
“Time Stamp Position” decides the display position of current time for each camera.
You can set the log file’s size in “System log” column. The default value is 2M. It will
automatically delete the earliest log when the size of saved log file exceeds the
established value. The size of log file can be changed.
When you select the “Except start alarm”, the system will send the alarm signal to remind
the users that it hasn’t enter the DVR system within the established time. Take the figure
3-15 for example. The established time is 2 minute.
Select other functions by your need.
Figure 3-15
.20.
3.5 System Information
What described in the system information is the name of the developer of this DVR
system and contact information.
3.6 Motion Detection of Video
System adopts MPEG-4 to develop the motion detection. After enable this motion
detection function, it can automatically detect the movement that happened in the
surveillance area. Once founding that there are movements in the detection area, the
system will automatically enable recording right now.
3.6.1 Motion Detection Setting

Right click the image, it will pop up a dialog box on motion detection setting for set this
functions.
Figure 3-16
.21.
3.6.2 Set the Areas for Detection
1) Right click the camera you want to set motion detection.

2) Press “ set detection area” button, it will appear gridding on the image.
Click the pieces of area to set the detection area, or click it again to cannel. Of cause,
you can click “ select all” to set this function through whole the video, contrarily, press the
“ clear all” to cancel all the detection area.
If you want to select a larger block of area, please hold on right click on image, draw it
from one point to another point, then the area between these two points have been
selected.
3.6.3 Set the Sensitivity of the Motion Detection

1) Press the “ sensitivity setup” button to show the motion area and do some set.
2)Click “up” or “down” button to adjust the sensitivity.
We recommend you to use the best sensitivity, because it can avoid mistaken-alarm well.
Press the “ display on the detection area” button to view the field that has taken place the
movement.
3.6.4 Enable the Motion Detection’s Function

.22.
After finishing parameter’s setup, confirm and" enable motion detection" button to
activate this function.
Figure 3-17
Yellow gridding means the

motion detection has enabled
Red: within the time range of alarm

attempter
Blue: beyond the time range of
alarm attempter
4. Playback
4.1 Playback
All the recording files in the hard disk can be found out to playback. There are two
modes for playback, single image and multi images. Click “playback” button to pop up
the images to display. Playback both the local record and remote record are supported.
Figure 4-1
.23.
4.2 Remote/ Local
You can choose the local record from local host or remote record from other hosts to
playback. The default selection is “local playback”.
4.2.1 Local Playback
Select “local” in the upper right corner to playback.
Select the server you want to playback from the drop down menu of “server”
column.
Select the camera No you want to playback from the drop down menu of
“Camera” column.
Select the date you want to playback on the “date” column.
Click “file record” button to show the list of files and corresponding information.
Click the different title button to arrange the list by different order. For example,
if you click “begin time”, the file will arrange by the increase order according to
time, if you click again, it will array by decreasing order.
Click the file or use the search engine to select the file you want to playback. If
the file has been selected, it will bright.
.24.
Double click the file to display, or use the “open” button is also OK. Click the
left button (as below figure 4-2) to playback a file, click the right one to playback
multi files. Multi file means all files below the selected one.
Figure 4-2
4.2.2 Remote Playback
Essential condition for remote playback: the “DSR-video” folder of remote DVR
server must be shared. For example, share D:\DSR-Video with the name of “DSR-
Video D”, and share E:\DSR-Video with the name of “DSR-Video E”, the rest may be
deduced by analogy.
Click “remote” button in the upper right of the video player. Input the server name
in the pop up dialog box. Click “OK” to wait for connecting the server. As following
figure 4-3
Other operations are the same as the ones of local playback.
4.3 Multi-channel Playback
DVR supports multi channels playback. There are two modes: synchronized playback
and non-synchronized playback.
Synchronized playback: click “ 4 channels synchronized” button to pop up a

dialog box. Select the camera you want to playback, and then select the date, file,
etc. as following:
Figure 4-4
.25.
Non-synchronized playback: you can use this function to playback 4 channels
videos with different recording time. Press “ 4 channels non-syn” button firstly,
and then choose the camera, the date and the file to display. (The dates must be
different)
4.4 Frame Processing
In the course of playback, you can use the “frame processing” button to do snapshot,
zoom, printing, saving, etc.
Click “ ” to do snapshot, and use “ ” to come back.
Figure 4-5
4.5 Functional Key for Playback

zoom: the size can be zoomed to be “50％”、“150％”、“200％”.
Renovate: repair the incomplete video file arising power cutting off or reboot.
Function: watermark function can prevent the picture from being distorted illegally. Click
“watermark” to pop up “Watermark extractor”, and then open the picture you want to set
this function from the “file” on the menu. Click “ ” to draw the watermark. If the picture
has been juggled, it will remind in the compare column. When you press “ ”, it will
show the position where has been juggled.
Please view the figure 4-6
Point out the regional position where has been juggled
.26.
Result for
inspection
5. DVR Configuration
5.1 Logon
Enter the Functional option of DVR configuration through “DVR configuration” button on
the tool bar. And also can enter it by clicking the icon of “DVR configuration” from the
“control panel” of Windows.
The landing of “DVR configuration” is the same as the one of system. Select the
available username and input the corresponding password to enter. In generally, only the
super has right to modify the system.
Figure 5-1
It will appear a series of setting option after landing. Such the dialog box as following:
Figure 5-2
.27.
5.2 Channel Distribution (used for the boards with the video expanding functions
such as 8R16D、、8R32D、、H128D)
“Channel distribution” is used in the non-real-time expanding video. The dialog box is
divided two parts from head to foot. Display and record channels appears in the upper
part, and all non-real-time resources of the video that support for you to select shows in
the lower part.
Operation steps:
1. Select and left click the resource from the lower part;
2. Left click the corresponding video that you want to display this channel in the upper
part;
3. Then the corresponding video will display the channel you have set.
4. If you want to cancel the video, right click the video in the upper part is OK.
Note:
A. The same card resource can’t be distributed to the two or above videos at the
one time.
B. If one channel is distributed to one corresponding video, it is real-time. If it doesn’t,
it is non-real time, and the resource has been averagely distributed.
Give figure 5-3 for example:

( Explain “card 1 channel 1” firstly, it means the first channel of the first CMOS chip on
the first Card. In another words, word “Card” in “card 1 channel 1” doesn’t mean the
first video board, it only represent the first CMOS chip. )
From the figure, you can see there is only one “card1” in the upper part. It means the
resource “ card 1 channel 1” is a single-channel in real time. Otherwise, there are two
“card 2” respectively distributed in video 2 and video 3 in the upper part, it means card 2
had been distributed to be two channels; the corresponding fps value is 12.5. In the
same way, you will found that “ card 3” has been distributed to be 3 channels. The
corresponding fps value is 25/3. And the channel 4 has been distributed to be 4 sub
channels. The corresponding fps is 25/4.
Figure 5-3
.28.
5.3 Alarm Alert
Enabling the “alarm Alert” dialog box, the system will send the alarm message when the
DVR alarm has been sprang. Users can select to activate the corresponding option by
need.
Figure 5-4
5.4 Alarm File Overwrite

.29.
If you active the “Alarm File Overwrite”, the alarm files will be overwirte by other files in
the process of the recording’s automatically circular process. If you wouldn’t active this
function, the alarm files will be saved in the hard disk forever.
Figure 5-5
5.5 Configuration Backup and Restore
“Configuration files” means the whole system’s configuration setting that set by “super”,
such as camera’s setting, option setup, DVR configuration, etc. this function apply in the
process of resetting DVR software. Only need restore it after resetting the software to
return to the primary configuration. It can avoid the trouble to set it again.
Figure 5-6
Backup: click “Backup” button firstly, and then select a folder to save the
content. Click “OK” to finish. As following figure:
Figure 5-7
.30.
Restore: enter the DVR configuration after resetting the software, select “restore”
button from the “configuration backup and restore” column. And then select the
backup folder; click “OK” to finish recovery. Operation is the same as the one of
“backup”.
5.6 Pan /Tilt /Zoom Control
click the box to be “√” to active the “PTZ control” function. As figure 5-8
Figure 5-8
5.7 Pan/ Tilt / Zoom
Use the “Pan/ Tilt / Zoom” to set the protocol of decode and to establish the remote PTZ
username and authority.
Configuration: the most important is to select the correct decoder’s protocol
and COM port and baud rate. Other options can use the default value.
As following figure 5-9:
Existing protocol inventory：

：
A：KALATEL KTD312
B：PELCO ASCII
C：PELCO SPECTRA
D：PHILIPS AUTODOME
E：UEL MV912RS
F：UEL_MV961A
G：ENKEL
H：ST_ 832
I：PELCO_P
J：VICON_SURVEYOR99
K：HUNTER
L：NRC_132
M：SUAMSUNG _SCC_641P
N：PANASONIC_CS850A
O：PELCO_D
.31.
User’s account: this accounts is offered to the remote client to control the PTZ
in the server end. The remote client can control the PTZ only when he has this
account.
Figure 5-10
Add new account: click “Add” button on the right hand of the picture above. Input
the username and priority, and then click “OK” to confirm.
Figure 5-11
5.8 Select Driver to Record

select the driver to save the recorded file from this dialog box. There is “√”in front of
the driver just means that this driver has already been chosen.
Note: it strongly recommends that don’t keep the files in system C: disk, Otherwise it
will influence systematic normal running seriously once when the files is too large to
occupy the most of room.
Figure 5-12
.32.
5.9 Time Stamp Setup
Use this option to enable the video to show the instant time. The default value is that all
video can show the time. But if you needn’t this function on some video, please cancel
the corresponding “√”.
Figure 5-13
5.10 Video Server User Manager

Can set the username, password and limitation for remote clients to monitor the server
video during this option. There are many kinds of visit limitation, such as password,
specific IP address, exclusive network card address of visit end (MAC mode of network
card); on the other hand, users can limit the bandwidth of every video transmission base
on the situation of net bandwidth.
.33.
Note: User need to select the “password protection”.
Figure 5-14
5.11 Add User
Add new users: after pressing “New User” button, input the “username”, ‘password”, and
“time limit” on the dialog box.
The defaulted value of “time limit” is O. It means the user can do view without
time’s restriction. If you change it to be 30 minutes for example, it means users only
can view the video for 30 minutes.
Audio and video that can be viewed: only the selected video or audio can be
viewed. The default situation is that all videos are available to view.
Remote unlock: the precondition is that there is electro motional lock in server end.
Click “√”to enable this function.
As following figure 5-15
.34.
5.12 Access Limitation
If you enable this function, the remote clients need to be validated when it visits the
server end. There are two modes for validating, one is through IP, and the other is
through exclusive MAC (the network card’s address).
IP address: select the username on the user column, select “IP address” in
lower right corner of the dialog box, ->press “access limitation” button to enter the
dialog box, ->select the camera and input the corresponding IP address, -> press
“Add” button -> press “OK” to exit.
As figure 5-16
MAC: the setting operation is the same as the one of IP address.
5.13 Network Bandwidth
Net bandwidth means the bandwidth value occupied by each camera when the server
sends the data to the remote end. The limit value can be changed according to the fact
situation.
Steps: Press “Network bandwidth” to enter the setting dialog box->select the camera->
decide whether to adjust the picture’s quality or not->select the bandwidth-> click “OK” to
exit after setting.
As figure 5-17:
.35.
5.14 Watchdog Setting
Watchdog is equipment can realize that DVR software and hardware monitor the system
jointly. It can make the computer to reboot within some set time after computer’s halt,
and also comeback to the primary status. It avoids missing some important recording.
Steps: enable watchdog firstly; -> select the card NO that watchdog installed in;->select
“in card” type; -> set the response time for reboot; -> click “OK” to exit after finishing
setting.
Figure 5-18
.36.
5.15 Time Open /close /Reboot computer
The systematical resource needs to be released regularly to get the better monitor
quality. Select the mode (such as time open the computer, time close the computer, time
reboot the computer) firstly, and then input the time, click “ok” to finish.
As figure 5-19
5.16 Property of Media Player

“Property of Media player” is setup for the hardware compression specially. Recording
playback needs to be supported by the different property of Media player because the
OVERPLAY of each graphics adapter is different. The defaulted formats are IYUV, YY12,
YUY2, YVYU and UYVY. Users can add the formats by needs. If it is not satisfactory
after append the setting, please press the “default” button to return to the default.
Note: if encountering black screen or serious mosaic when playback in D1 mode,

please selects RGB32 only, and then click “Confirm” button to save.
As figure 5-20:
.37.
5.17 Video Revolve
The angle of video needs to be revolved in some especial situation such as in ATM
application. This function supports the angle of video rotate 90 degrees. Enable“ revolve”
that behind the corresponding camera you want to do revolve. The revolved image is
slightness. The picture can be widened and full of the showing window, but the resolution
is not very nice. So we recommend not using “stretch” function.
Figure 5-21
5.18 Select “PAL” or “NTSC”

Users can select “PAL” or “NTSC” according to the actual input signal of the video.
6.Tool Bar Function
Move the mouse to the upper left corner of DVR main screen. It will pop up a tool bar
with many function buttons. Click “ ” to keep showing the tool bar, click again to hide it.
As figure 6-1
Explain:
a) Keep the tool bar
b) Zoom in
c) Zoom out
d) Restore
e) Channel switch
.38.
f) Take photograph in scene
g) Listening
h) Volume set
i) Quality set
j) View log
k) Image shelter
l) Desktop
m) DVR configuration
n) Manage pictures
o) Map management
p) Other windows
q) Help
6.1 Zoom in, Zoom out, Restore

Zoom in: it only support electronic zoom. Click “ ”firstly, and then select and
click the point of the area you want to zoom in.
Zoom out: click “ ”button, select and click the point of the area you want to
zoom out.
Restore: click “ ”and right click the certain camera to return to the primary
status.
6.2 Channel Switch

Use “ channel switch” to define the display position for every channel.
Click “ ”button in the tool bar and click to select a surveillance position that channel
want to show within the video monitor area, and then select and double click the channel
that need to be monitored from the display panel. That video image will display in the
appointed monitor position.
6.3 Take Photograph

The users can take photograph by using this function.
Click “ ”button, and then click the channel you want to take photograph, one click to
get one picture, double click to get two pictures.
6.4 Manage the Picture

Use this button to do manage the picture you have taken. You can do save, print and
delete. The operation is the same as the Windows system.
You can use “channel selection, begin time and end time” to find out the picture.
Figure 6-2
.39.
6.5 Listening
press “ ”button, select the channel NO you want to listen the scene voice.
6.6 Volume Set

click “ ” button to adjust the volume until it is fit for listening.
6.7 Quality Set of Image

The control result of the image will be influenced by the change of outside light according
to the different time slot, use “quality set” to regulate to the best video picture quality.
Through regulate some parameters such as brightness, contrast, chroma, saturation, etc.
Click the“ ”to pop up the dialog box.
After regulating to the best quality, the users can save this best status in the temporary
storing device through right click the number of “ ” in the following
figure 6-3. There are 5 temporary storing devices. Users can select the best one after
comparing these 5 results.
Users can also regulate the video quality according to the different light between daytime
and nighttime. Click the box before “night” to be “√”-> input the time slot for switching;-
>Press “day/night” button to enable this function.
Figure 6-3
.40.
6.8 Log
“Log” records every operational process. It will detailedly record who, when, and do what.
Press “ ”button-> select the date to view the log.
Figure 6-4
6.9 Image Shelter
In generally, this function uses in some special occasion (such as national treasury of the
bank). Some confidential areas must be sheltered because these areas are not able to
view by anybody except authorized manager. This shelter will be automatically canceled
only when alarm has taken place.
.41.
Steps: press “ ”button;->Right click the video you want to set “mask” function;->
select the areas to shelter from (24*32 areas);->enable mask function;->decide whether
it will apply in recording or not.
Figure 6-5
6.10 Desktop
The desktop has been hidden when running the DVR system. The authorized users can
click “ ” button to pop up a startup bar, click “ ” button in this bar to minimum
the DVR interface and show the desktop of Windows.
6.11 Swift Key of DVR Configuration

There is a “DVR configuration” swift key on this tool bar to facilitate for users to use. It
avoids the trouble that users must exit the DVR system and start the “DVR configuration”
on the “Control Panel”.
Steps: click “ ” to pop up a dialog box, input the username and password. Please
consult the “DVR configuration” part to see other settings.
6.12 Others
There are two functions setting in “others” button, one is “ net video server”, the other
is “alarm send option”. Click “ ”to select.
Net video server: users can use this function to view which remote users are
connecting with this local host. And users can encrypt for the data or cut the
connection by need.
“Encrypt data” means do encrypt for the data that is in transmission. If there is no
USB soft dog in the “remote monitor center” software, the client end must enable this
function, or the data will unable to transmit.
“Enable net register” means this server will register through Internet. If it has
enabled this function, the client end will be able to visit the server by inputting the
server name when the connection is through dynamic IP net. It is strongly
recommended to select this function.
.42.
Figure 6-6
Alarm send option: it means that the video with alarm status will be sent to the
remote administration center. The “username” and “password” is the ones that the
local server has offered to the remote center.
Figure 6-7
6.13 Help
press “ ” to resolve your puzzle or ask for help.
6.14 PTZ Control Client Information

Through “PTZ control client information” function, users can control the direction of PTZ,
can regulate the camera’s “zoom”, “aperture” and the “focus”, and also can control
remote lamp open/close, open the lock and so on.
Figure 6-8
.43.
6.14.1 Select Camera
Select the camera from the camera selection box on the PTZ control panel.
Note: camera number of decoder must match with the one of the connected camera.
6.14.2 Control Speed

Control the PTZ’s speed through the sliding control box.
6.14.3 Control PTZ’s Focus

After selecting the camera, click arrowhead button to control the direction, focus and
multiply.
6.14.4 Pre-position
The positions of the PTZ can be saved so that the camera can return to that position
when wanted.
Set pre-position: input the number of pre-position in the pre-position box. Adjust
the camera to the perfect position after selecting the pre-position number. Click “set”
button to award this number to this position.
Show the number of pre-position:

Input the number of pre-position, Press the show button to send the camera to the
saved pre-position.
Pre-position hot keys: Four hot keys are implemented for four frequently used pre-
positions.
After setting, press these hot keys will send the camera to pre-position accordingly.
Figure 6-9
.44.
Left click to cancel the PTZ control
Right click to select server, do diagnose
and exit
Right/left click to regulate

the zoom, lris and focus
Click arrow to adjust

the PTZ’s direction
Camera
NO
Remote control
indicator light and
lock on/off
7 Alarm I/O Connections
7.1 External View of Connectors
Gnd In9 Gnd In10 Gnd In11 Gnd In12 Gnd In13 Gnd In14 Gnd In15 Gnd In16 GND OUT1 GND OUT2 GND OUT3 GND IN1 GND IN2 GND IN3 GND IN4 GND IN5 GND IN6 GND IN7 GND IN8
9-16 channel alarm input 1-3 channel alarm input 1-8 channel alarm
i t
Figure 7-1
Alarm inputs Alarm outputs
Pin NO Designation Pin NO Designation

In1 Alarm input1 Out1 Alarm input 1
In2 Alarm input 2 GND GND
.45.
In3 Alarm input 3 Out2 Alarm input 2
In5 Alarm input 5 Out3 Alarm input 3
In7 Alarm input 7
In8 Alarm input 8
In9 Alarm input 9
In10 Alarm input 10
In11 Alarm input 11
In12 Alarm input 12
In13 Alarm input 13
In14 Alarm input 14
In15 Alarm input 15
In16 Alarm input 16
Gnd GND
7.2 Alarm Output Configurations
Sensor Alarm Output Motion Detection Alarm Output video missing alarm
Alarm Output 1 Yes Yes NO
Alarm Output 2 Yes No NO
Alarm Output 3 No Yes NO
Alarm Output 4 No No Yes
7.3 Alarm Connection Wiring Diagram
Figure 7-3
+12V
J
GND
GND OUT1 GND OUT2 GND OUT3 IN1 GND IN2 GND
7.4 Alarm Connector of D Type
Alarm connector of D type is another equipment for alarm I/O. It will occupy one PCI
because it will be inserted in the PCI port. The connection is as following figure 7-4
.46.
8. Decoder’s Instruction
8.1 Device Summarize
Pan/Tilt OSRD is a former control device match with the security surveillance device, the
control format are RS-485 and RS-232. It can control the pan/tilt inside and outside of
room, electro motion lens, camera and shield.
This device doesn’t recommend to installing at flammability location.
Please select the correct voltage for work.
8.2 Device Introduction

The indication light illuminate to show the power is natural. When the decode
single is correctly received, the indication light blacks out one second.
DATAA、GND、DATAB：Communication 485 port
RS232 、GND：Communication RS232 port
The communication ports that selected by Sk4 are 485 port and RS232 port.
Figure 8-1
IRIS FOCUS
ZOOM GND
Figure 8-2
UP DOWN
LEFT RIGHT
AUTO COM
Pan/toil voltage: select 24V, 220V voltage respectively.
.47.
Pan/toil NO: can define 1-99 cameras and select tens digit or ones place digit by
SK2, SK3.
Select pan/toil confer: click SK1 to select pan/toil control protocol, O-VICON-
SURVEYOR99 protocol, I-PELCOD protocol.
Self check switch: can output one testing signal of every action in turn.
12VDC: 12V voltage output of direct current; 500MA electric current that can
provide power for camera.
LAMP1: can provide close contact for light control. Click 1 key under the ON
button in pan/toil controller to connect DK1-DK1, click again to cut. 2 key under
the ON button is camera power switch, 3 key under the ON button is AUX1
contact switch, click it can control the short circuit contact of relay but can’t
connect to the light directly.
LAMP2: can provide close contact for light control.
AUX 1: provide normally open switch.
AUX2: provide normally close switch.
Baud rate setting:
Figure 8-3
1 2 Baud rate 1 2 Baud rate
ON 2400 ON 4800
ON OFF
OFF ON 9600 OFF 19200
OFF
8.3 Connection Sketch Map
Figure 8-4
RXD R R 485A DATA Decoder

S S A
MAINFRAME GND 2 CONVERT 4 GND GND
3 ER 8
TXD 2 5 485B DATA
B
DVR through RS232 and convert to RS485, then reach DATAA, DATABGND to the
according port of OSRD
8.4 Device Function Switch, Connection Sketch Map
Figure 8-5
.48.
Indicator GND
light
24V IRIS
Pan/toil SK1 FOCUS
Voltage
220V Pan/toil ZOOM
Protocol
COM
UP
DOWN
PTZ ON BAUD LEFT
NO RATE
Tens RIGHT
digit
SK2 AUTO
OFF 12
Ones SK4 LAMP
place
digit
SK3 Self LAMP 1
Check
485 RS232 AUX1
AUX1
AUX2
232 in GND 485-B 485-A GN 12VDC AUX2
D
RS232 GND DATA-B DTAT- GN 12V
A D
8.5 Technique Guild Line

Provide power: AC220V, 50Hz
working voltage for Pan/toil: AC220V、AC24V
Working voltage for lens: DC6-12V
Control mode: RS-485
Control mode: STP
Size: 235mm(length)*155mm(width)*65mm(height)
Note:
The last decoder must meet a matching 120Ω resistance between DATAA and DATAB if
connecting with more than one decoder.
9.Single-Channel Remote
DVR2000 remote have strong functions such as remote surveillance, remote monitor,
remote tall back, remote recording, playback, remote control (indication light and lock
on/off), remote control PTZ, patrolling, remote receiving alarm and so on.
Note: please make sure the web is expedited before connecting remote surveillance
software.
There will automatically create a shortcut icon on the Windows interface after the single
screen remote software having been installed. Following the below figure 30. Double
click the icon, there will pop up an operation interface as figure 31 on the upper right
hand of the screen.
.49.
Figure 9-1 figure 9-2
9.1 Connect Server
Chose servers firstly and then click “video interface” “server” to pop up following dialog
box:
Figure 9-3
9.2 Setup the Server Mode
9.2.1 Add Server
Click “set” button in the video server, pop up a dialog box following figure 33
Figure 9-4
.50.
Input correspond content in every label box of figure 33, then click “add” key. If you want
to monitor more than one server, please input correspond content of another server by
the same way.
After setting, click “OK” to return main interface, select the server name you want to link
to, press “OK”.
Note:
If server and surveillance center is linked by dynamic IP network, you must draw “” in
the “logon” to allow the server can logon by user resolution server.
9.2.2 Modify, Delete Server

If the server setting is error, please select the error server in the server list and make it
become blue color, and then click “modify” again after finish modify by click “modify”
button, press “OK” to return main interface.
9.3 Logon Server
9.3.1 Logon Server

After set the server, return to main interface as figure 32. Select the server want to land
in the drop down menu, click “OK”. It will pop up a dialog box as figure 34 after many
seconds. Input user name and password provided by server port, click “OK” to logon
server and to monitor remote image.
Note:
You must draw “” in “save password” to avoid input user name and password again
when you want to view second channel and third channel.
.51.
Figure 9-5
9.3.2 Logon Server Directly

There is a method to logon server directly instead of logon through server setting.
Click “<<” in the main interface as figure 32 swap to another logon method like figure 35,
input server name (that have registered) or the server IP address, press “OK”. It will pop
up a dialog box as figure 34 after many seconds. You only need to input user name and
password to logon. The other method is that clicks “scan” and directly selects the server
you want to monitor in the network (available in the LAN), other operation are the same
as upper.
Figure 9-6
Input server name or IP

address directly
Enable logon function

Select server in the
Network directly
.52.
Figure 9-7
9.4 Remote Setting
9.4.1 Select Camera

Click “camera” and select the channel you want in the drop down menu to view different
camera channel.
.53.
Figure 9-8
9.4.2 Remote Record, Playback

If you want to do remote record, please click “record” and select “Start” in the drop down
menu to record, press “stop” to stop and click “playback” to return playback interface
after many seconds, you can refer 4.5 part to know the playback operation.
Figure 9-9
9.4.3 Adjust Surveillance Resolution

Select different surveillance resolution according users’ different taste. Click “ resolution”
to select.
.54.
The image will be more clear and small when showing by less resolution. The standard is
384*288.
Figure 9-10
9.4.4 Adjust Compression Ratio

Compression ratio is set for remote record. In generally, users use the standard setting
of the company instead of setup again. But the record setting can be set according
users’ need.
Following figure 40
Figure 9-11
Record time of Select save disk

one file NO of record file
.55.
Note:
The record time can be select by will, but the disk NO usually is more space disk except
C: (system disk).
After setting, please click “save” “OK”.
9.4.5 Patrolling Setting

Patrolling function means that the monitor interface can automatically swap to the
camera channel that had been set in the limited time when there is no person doing
monitor. It will facilitate the user to play back the status of patrolling camera when he has
free time.
Detailed setting following figure 41
Figure 9-12
Patrolling start
time Patrolling end
time
Select sever you
want to do Select camera you
patrol want to patrol
Input user name

Input user
Aim list of password
patrolling
9.4.5.1 Add, Modify, and Detect the Patrolling Aim
Add: click “add” button after camera channel has been set according user need. If you
want to add another camera channel, please select other camera No, after input the
corresponding content click “add”.
Modify: select the aim wanted to modify in the patrolling aim list, and click to change the
color to blue, and then modify the corresponding content in every boxes. Finally click
“modify” “OK” to return to main interface.
Delete: select the aim want to modify in the patrolling aim list, click to become blue color,
and then click “delete” “OK” to return main interface.
After setting, it will OK after select “start” in the drop down menu of “patrolling”.
9.5 Remote Control
9.5.1 Logon Password
.56.
Click right mouse after enter the surveillance image. The main interface will pop up a
drop down menu as figure 42: click “ logon password” to disappear the dialog box as
figure 34, and then input the correct user name and password. Click “OK” finally.
Figure 9-13
9.5.2 Display Control
There are 3 options in the display control such as “display status bar”, “display detail bar”
and “display instant status”. Other is “ hidden bar”.
Enable “display status bar”, it will add a bar with “ frame size”, “frame count”, and a
status bar with current time and surveillance time in the bottom of main interface.
Enable “display detail bar”, it will disappear some detailed status information to be clear
at a glance in the bottom of main interface.
If you needn’t this detail information, please select “hidden bar”.
The detail information following figure 43
Figure 9-14
.57.
Main
interface
Detailed status info

Instant status info
Status bar info
9.5.3 Audio Control

Remote audio control can enable remote monitor, tall back and other audio dealings
under the status that server input correct audio.
Note:
The monitor port must install microphone and sound box.
Monitor: select “start monitor” in the drop down menu.
Talk back: select “talk” under the monitor status.
Other options can be select according the users’ need. Like figure 44 following:
Figure 9-15
.58.
9.5.4 Full Screen Display
You only need to select “full screen display” button in the drop down menu in figure 9-15
to display the view image by full screen.
Click left mouse in the full screen to return to original image.
9.5.5 Remote Control

The remote system set, remote light the lamp, open the luck and other series functions
will be realized in the remote control option.
Remote system set: select “ get system setting or log” to pop up a dialog box as following
figure:
Figure 9-16
Server super
password
Input the super password, click “OK”, then you can set the remote system in the system
setting box that pop up after seconds. Please refer to “user guider” to see setting details.
If you want to get the server’s log, please click “OK” after affirming the start date and day
of log you want to view, wait for seconds to view the detailed log information by linking to
network successful.
Remote indicator light and lock on /off:

Select “ON/OFF light” and “open the lock” buttons in the drop down menu to control
remote indicator light and lock.
Note:
The electromagnetism lock and electro motion lock in the server can automatically close
several seconds after starting.
Other:
The user can select other options according control need. Following figure 46
Figure 9-17
.59.
9.5.6 Cut Connection/ Close Window
Select “cut connection” in the drop down menu like figure 46 to cut the current link.
Select “close window” or click “” on the upper right hand of main interface to close the
current monitor interface.
9.6 Remote Playback
Note: if you want remote playback, you must share the file that agree doing remote
playback firstly.
There are two formats of playback: one is remote playback, and another is local playback.
Click the green triangle button of “playback”. If it is remote playback, you can input server
name (have been registered) or IP address in the pop-up dialog box, and then click “ ok”.
If it is local playback, you just can click “local” to enter the playback interface in the pop-
up box directly.
Figure 9-18
The operation of playback is the same as the one of server playback: select camera
name select date select play file play.
Please refer to “record playback” department.
9.7 Remote Alarm Receiver

The remote alarm receiver means to the monitor side will receive the alarm information
and pop up that camera image immediately when the alarm happened in the service side.
It makes the monitor side can see the status and deal with in time.
.60.
It will appear a head portrait icon in the lower right side of Windows by clicking and
starting “alarm receiver” button. Click right mouse in the icon to pop up a dialog box, if
you want to exit receive, please select “exit” directly. If you want to view the alarm
information and doing corresponding setting, please select “ resume” to pop up the
dialog box as figure 48.
There are two departments of alarm receiver: one shows current alarm information, and
another records history alarm information. Alarm information points out “channel”, “alarm
server name”, “status”, “alarm date”, “detailed alarm time” and “alarm type” in detail.
Set: click “set” button to pop up a dialog box as figure 9-19.

Permit auto link: the monitor side not only can receive current alarm information,
but also can auto pop up the alarm camera image, and then input the user name
and password provide by server in the pop-up dialog box.
Only pop up alarm window: the monitor will pop up a alarm information window
instead of pop up the camera window at once there are alarm happened in the
server side.
Alarm tip: there are two mode of sound. One is “DI” voice that the software own;
another is the sound the users can set by their will. Click “scan” and select WAV
mode sound file in the mainframe.
Alarm linkage: this function only can be used on the guidance edition with
electronic map. Draw “” in the front box and input the title of alarm linking in the
back blank box.
After setting, click “OK” “close” to exit.
Figure 9-19
Figure 9-20
.61.
9.8 Remote PTZ Control
Remote PTZ control means the server side can change the direction of pain/toil, adjust
the camera “zoom”, “lris” and “focus”, and can control remote indicator light and lock
on/off and so on.
Click PTZ button to start PTZ controller, input server’s name or IP and user’s name that
provided by server side in the pop up dialog box. Following figure 50. Detail operation
please refers to figure 9-21.
Note: it will support user whose name has add to the user list in the PTZ control
server to logon.
Figure 9-21
Camera select
Use the camera select box in the PTZ control panel to chose the camera that
controlled by PTZ.
Note: the setting of OSRD camera number must correspond with the linked
camera number.
Speed control
The moving speed of PTZ can be control through slide.
Pre position
The position of PTZ can be saved in order to make the camera back the position by
need.
Set pre-positions: input the pre position number in the pre position box.
Adjust the camera to the pre-position up/down, right/left after select pre position
number. Click “set” button to distribute the pre position to this station.
Display pre-positions: input pre-position no. Click display button to set the camera
to the pre position.
.62.
Pre-position hot key: have supported pre-position hot key for the four pre-position
that in common use. Use the hot key can adjust the camera to the corresponding
pre-position after the successful setting.
Figure 9-22
10. Installation of Boards
10.1 Installation of Software Compression Boards
HengTong DVR2000 video boards support machine case system and PC system. Only
need to insert the video boards in the corresponding PCI slot.
Check your goods following hereunder list:
.63.
1. One piece of DVR2000 boards.
2. one piece of audio line that with 4 cores (only fit for H1RT、H1RT-W、H4RT、
H4RT-W)
3. fittings for expanding audio (A4) (only fit for S4R、S4R-W)
4. one piece of watchdog (only fit for S4D-W、S4R-W、H1RT-W、H4RT-W)
5. fittings for expanding audio and video (V12A4) (can be chosen and only fit for
S4R、S4R-W、H4RT、H4RT-W)
6. D165fittings for I/O alarm (can be chosen)
7. 142R V3.0、142R V3.2 fittings for I/O alarm (can be chosen)
The corresponding fittings connect with the connector as the following figure: (just for
consulting)
Figure 10-1
Video boards of HengTong DVR2000-S4D and its fittings (software compression)
10.2 Installation of Hardware Compression Board
Figure 10-2
Video boards of HengTong DVR2000-H4RT and its fittings (hardware compression)
.64.
If what you used is a DVR2000-H series video board, please connect the OUT insert
slots on the board to the CDIN slots that is in the sound card.
If what you use is multi pieces of DVR2000-H series video cards, please connect the first
video card’s OUT insert slots with CDIN slots that is in the sound card, then insert the
next card’s OUT slots to the last card’s IN slots.
After affirming the articles is all right, following method that is referred above to install the
DVR2000-H series video cards. Connect the video cards to the sound cards, and then
insert the cards into the PCI slots.
Figure 10-3
.65.
11. Install the Driver
11.1 Install the HengTong DVR2000 video cards driver under the WIN98SE op
eration system.
1) After install the cards, and enter the operation, it will pop-up a dialogue box as
“add new hardware wizard”，now click "next"，
2) select "Search for a suitable driver for my device(recommended)"，click "next"
.66.
3) and then put the CD of HengTong DVR2000 into the CD driver, select “Specify
a location:”，click“Browse..”，The route points to the Driver\ Win98 folder under th
e CD disk’s root catalogue.
4) now, the system shows “windows is now ready to install the best driver for this
device”，click “next”，
.67.
5) Last click “finish”
If there is multi-channel video card installed in your computer, please repeat upwar
ds steps until finishing the installation.
Finished the installation, it will pop up the device driver “Audio Capture” and “Video
Capture Device” under the "sound, video and game controllers" option in my com
puter’s device manager
.68.
11.2 Install HengTong DVR2000 video cards driver under WIN2000.
1) After installed the video cards and enter the operation system, it will pop up a
dialogue box “Found New Hardware”，click“Next”，
.69.
2) and then select “Search for a suitable driver for my device(recommended)”，clic
k “next”，
3) choose “Specify a location” in “Optional search location” ，click “Next”，
4) And then put the CD of HengTong DVR2000 into the CD driver; point the route
s of “Copy manufacture’s files from” to the HTC-Driver\ Win2k\Chi folder under the
CD disk’s root catalogue, then click “OK”.
.70.
5) The system will show “Windows found a driver for this device”, and then click
“Next”, as following:
.71.
6) Click “yes” to process the driver’s installation, last click “finish”.
Finish installation, it will pop up “Fujan HengTong TM1300 Hard Compress Board
(Win2000)”device driver under the option of “Sound、video and game controllers” in
my computer’s Device Manager.
.72.
11. 3 Install HengTong DVR2000 video cards driver under WINXP.
1) After installing board, enter the OS. Once it pop up a “ hardware update guide”, please
select “ install from the list or pointed situation (great)” please click “Next”.
Figure 11-16
.73.
2) Put the DVR2000 CD in the optical disk drive, select “including this location during
searching (O):”, click “browse” to find out “HTC-Driver\ Win2k\Chi” folder from the optical
disk root directory, after click “OK”, then click “Next”.
Figure 11-17
3) Click “ continuing (C)” in the pop up dialog box:

Figure 11-18
.74.
4) Click “finished” finally.
Figure 11-19
.75.
Finish installation, it will pop up “Fujan HengTong TM1300 Hard Compress
Board(Win2000)”device driver under the option of “Sound、video and game controllers”
in my computer’s Device Manager.
Figure 11-20
Figure 11-21
.76.
None “!” means the installation of driver has completed.
Note:
Users need install “ driver for HengTong memory device” when using DVR2000-S series
boards.
Steps:
i. Double click “ add/remove the hardware guide” from the control panel.
ii. Click “Next”, and then select “add/ remove the malfunction” .
iii. Click “Next”, the Windows is searching for hardware device now.
iv. Select “ add new device” from the pop-up dialog box, and then click “Next”.
v. Select “NO, I want to select hardware from list (O)”, click “Next”.
vi. Select “other device”, and then click “Next”.
vii. Click “ install it from disk (H)”.
viii. Put the DVR2000 CD in the optical disk device, and then click “browse”.
ix. Change the path to be “HTC-Driver\ Win2k\Chi” under root directory of the
optical disk, and then click “OK”.
x. Select “ HengTong Driver for the device of memory control”, and then click
“NEXT”.
xi. The Windows is installing the driver now, please click “Next” to continue.
xii. Finally, click “ finished”.
12. Install the Internet Application

It is time to install the Internet application after installing the driver. HengTong DVR2000-
S series boards need to match the software compression software to use. And
HengTong DVR2000-H series boards need to match the hardware compression software
to use. The installation processes for this two software are the same.
Steps:
1) Open the software catalog firstly, running Setup program, and then click “Next”.
Figure 12-1
.77.
2) " The license agreement " dialog box appears, then please click " (Y) "
Figure 12-2
3) Click “ browse” to find a destination to install, click “OK” to confirm. In generally,

using the defaulted destination is OK. Then click “Next”.
Figure 12-3
.78.
4) Select the corresponding “Type for install”. There are three types for installing
software compression: “ HengTong DVR2000-8R” “HengTong DVR2000-8R16D” and
“ HengTong DVR2000-8R32D”. And there also are three types for installing hardware
compression: “ HengTong DVR2000-H16RT”, “HengTong DVR2000-H32RT” and
“HengTong DVR2000-H128DT”. Click “Next” to continue.
Figure 12-4
5) It will pop up a dialog reminding that it is copying the files, please click “Next”.
Figure 12-5
Figure 12-6
.79.
6) After finishing the installation, it will pop up a message as figure 12-7.
7) It will ask whether to reboot computer at right now or not, please select “ yes” to reboot
the computer.
Figure 12-8
.80.
8) Finally, click “finished”. After rebooting, the installation is completed.
3. Common Trouble and Solution
13.1 Frequently Halt
System halted every two minutes on average. The reason may be one or mix of the
following reasons:
1) It may be caused by the mistake of the hard disk. Hard disk takes place error
and lead to the fact unable to write data into. It will halt and enable the
watchdog function once writing the data into HDD. Sometimes, it enables the
safety mode after rebooting; in this case, the system is easy to halt when
operating.
Solution: adapt “ scan the disk” under Windows system. If it won’t resolve the
problem, please considering formatting the HDD or changing for a new one.
2) May be it is because of the iffy video capture board. Please instead for a new
one.
3) The reaction time for enabling watchdog has been set to be too short. It also
can cause this problem.
4) May be CPU fan has broken. The CPU is too hot to cause the computer’s halt.
Please exchange the fans.
13.2 Display Incapability

Power supply is normal, but it cannot find out the hardware in host, the display flashes
and flashes. In generally, the reason is that there is questionable trouble in main board
.81.
or video boards. Please try to enter the system after removing the video boards. If it still
cannot run, please exchange the main board.
13.3 Circulation is Unable

The circulation is unable while the display interface is normal as before.
1) One of the reasons may be is that users haven’t enable “ circular recording”. Please
set the recording mode to be “ circular recording” from the “ recording” column in
“Utility”. Exit the software and enter again.
2) Another reason may be is there is problem in the hard disk. Please exit DVR2000
software to scan the hard disk. If it will appear some files named *.CHK, please
delete it at right now.
13.4 Catalogue Establishing Failed.

If it suddenly pop up a message to alarm that “ catalogue establish failed, it cannot do
recording.” when running the software. The reason is the hard disk. Please scan it. If the
problem is still exist, please change the HDD.
13.5 Invalid Operation

If it will pop up a message that “ this procedure will be closed up because it carry out and
operate illegally, please contact with dealer. The host will reboot after you close this box.”
And after rebooting, the message will pop up again. Please reinstall the software to
resolve this problem.
13.6 Time Lack when Recording

1) Please confirm whether the time setting for recording excess the stated time or not
(such as excess the 10 hours or 20 hours)
2) Inspect whether you have enable the motion detection. If you have enable
this function and the most time for every recording files are 15 minutes.
Please reduce the sensitivity for detection. Or please select some areas
where movements frequently take place in instead of selecting all the areas.
3) Another reason cause this problem may be that there are two computer
names in this PC. Please delete one.
13.7 Distort Alarm

If it encounters distorting alarm when processing the motion detection, the reason is that
the video signal is not very good and the image is fuzzy not clear. Please befittingly
decrease the sensitivity.
13.8 Alarm All the Times

Please check whether short circuit exists in the alarm bar. Try to pull out the line of alarm
bar, if it still alarm, please check whether the alarm line has problem. If this scheme is
still failed, please check the video boards to find the reason.
13.9 Splash or Blank Screen During Hardware Compression’s Playback Process

Because the display format and overlay technology that supported by graphics adapter is
different, there might be appears splash or blank screen in some type of graphics
adapter during the hardware compression playback process. Users can following below
setting to resolve this problem.
.82.
1) Open the “media player property” in the “DVR configuration” from “control panel”.
Following below picture:
Figure 13-1
2) Enter the setting following:

Figure 13-2
.83.
3) Users can try to set it to be RGB32 mode, because it fits for most of the graphics
adapter, and then click “confirm” button:
Figure 12-3
.84.
4) Click “OK”, and the phenomenon of splash and blank screen will clear away
when playback again.
Note: if you use D1 result to record, recommend using RGB32 mode!

If you use CIF format to record, you can choose another format to improve the im
age quality.
Such as YUY2
Figure 13-4
.85.
Try to test whether it will appear splash or blank screen or not. If appears, please
choose another format until to resolve the problem, if not, the quality of playback
will be improve, and the establishment of the graphic adapter succeeded at this m
oment.
If the playback of AVI file cannot process in DVR host computer, you can set it in
the media player of Windows. Right click it during the playing process, and choos
e “property” in the menu, following:
Figure 13-5
.86.
It will appear the following picture:
Figure 13-6
.87.
Choose “Fujian HTC MPEG-4 Video Decoder”, and then click “property” to po
p up the following picture:
Figure 13-7
Complete the setting, please exit the player and open it again to test the result!
13.10 Abnormally Display

The screen only shows DVR2000 picture after entering DVR2000, there is no natur
al operation interface in the right of screen, and you cannot doing natural operate.
(Following below picture)
Figure 13-8
.88.
The reason is that the resolution for OS has been set to be 640*480, so the system only
can work when the distinguish ratio is 1024*768.
Figure 13-9
13.11 The Image is Indistinct
When DVR2000 received the image signal from every channel, but the display result is
not very clearly as cover a block of gauze in the camera lens.
Figure 13-10
.89.
The reason is that the display color for OS has been set to be “24 bits indeed multicolor”
or “32 bits indeed multicolor”. The solution is to set it to be “16 bits buildup color”,
because the result is best in this case.
.90.

HengTong DVR2000 User Manual PDF

Uploaded by

Copyright:

Available Formats

HengTong DVR2000 User Manual PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HengTong DVR2000 User Manual PDF

Uploaded by

Copyright:

Available Formats

User Manual

User Manual for HengTong DVR2000

2. Enable the System

3.3 Record Setting

3.4 Option Setting

3.5 System Information

3.6 Motion Detection of Video

User Manual for HengTong DVR2000

4.2 Remote/ Local

4.3 Multi-Channel Playback

4.4 Frame Processing

4.5 Functional Key for Playback

6.Tool Bar Function

User Manual for HengTong DVR2000

6.14 PTZ Control

7 Alarm I/O Connection

9.2 Setup The Server Mode

9.3 Logon Server

9.4 Remote Setting

9.5 Remote Control

User Manual for HengTong DVR2000

9.7 Remote Alarm Receiver

9.8 Remote PTZ Control

10. Installation of Boards

11. Install the Driver

12. Install the Internet Application

13.Common Trouble and Solution

User Manual for HengTong DVR2000

HengTong DVR2000 adopt MPEG-4 compression mode. It has been designed to

1.2 Standard Functions

Digital surveillance recorder and multi-menu processor

Support up to 128 camera input with multi display modes;

Support PAL and NTSC form

User Manual for HengTong DVR2000

Can realize up to 32 channels video real- time displaying and recording

Real time digital Video compression

Can carry on the operation of multiple tasks at the same time,

Have multi search mode on playback function;

Prevent the video video from being distorted

Alarm triggered recording

Alarm I/O interface

Can change calculagraph to set the recording time.

Motion detection alarm recording

Easy to expand by software upgrade and system integration

Support multilingual capability

Doing alternate on-line visit and playback though dialing-up, LAN.

Recommended setting: CPU: greater than Intel PⅢ, above 1GHZ.

CPU for soft compression : recommend Intel PⅥ ,above 2GHZ

EMS memory: 256M

Graphics adapter: graphics memory above 32M.

Power: recommend using ATX power, 350W

Note: recommend using mail board of INTEL chips group.

User Manual for HengTong DVR2000

2.1 Open the Power

Main interface as Figure 2-1

After enable the system, it will show the main interface.

Click the Logon button; it will pop up a Logon dialog box

3.1 Camera Setting

After setting, click “OK” to return. As following picture: