Working Principle of Transformer

Working Principle of Transformer
The basic principle on which the transformer works is Faraday’s Law of Electromagnetic Induction or
mutual induction between the two coils. The working of the transformer is explained below. The
transformer consists of two separate windings placed over the laminated silicon steel core.
The winding to which AC supply is connected is called primary winding and to which load is connected
is called secondary winding as shown in the figure below. It works on the alternating current only because
an alternating flux is required for mutual induction between the two windings.
Contents:
 Transformer on DC supply
 Turn Ratio
 Transformation Ratio
When the AC supply is given to the primary winding with a voltage of V1, an
alternating flux ϕ sets up in the core of the transformer, which links with the
secondary winding and as a result of it, an emf is induced in it called Mutually
Induced emf. The direction of this induced emf is opposite to the applied voltage V1,
this is because of the Lenz’s law shown in the figure below
Physically, there is no electrical connection between the two windings, but they are
magnetically connected. Therefore, the electrical power is transferred from the
primary circuit to the secondary circuit through mutual inductance. The induced emf
in the primary and secondary windings depends upon the rate of change of flux
linkage that is (N dϕ/dt).
dϕ/dt is the change of flux and is same for both the primary and secondary
windings. The induced emf E1 in the primary winding is proportional to the number
of turns N1 of the primary windings (E1 ∞ N1). Similarly induced emf in the
secondary winding is proportional to the number of turns on the secondary side.
(E2 ∞ N2)
Transformer on DC supply
As discussed above, the transformer works on AC supply, and it cannot work not
DC supply. If the rated DC voltage is applied across the primary winding, a constant
magnitude flux will set up in the core of the transformer and hence there will not be
any self-induced emf generation, as for the linkage of flux with the secondary
winding there must be an alternating flux required and not a constant flux.
According to Ohm’s Law
The resistance of the primary winding is very low, and the primary current is high.
So this current is much higher than the rated full load primary winding current.
Hence, as a result, the amount of heat produced will be greater and therefore, eddy
current loss (I2R) loss will be more. Because of this, the insulations of the primary
windings will get burnt, and the transformer will be damaged.
Turn Ratio
It is defined as the ratio of primary to secondary turns.
If N2 > N1 the transformer is called Step up transformer
If N2 < N1 the transformer is called Step down transformer
Transformation Ratio
The transformation ratio is defined as the ratio of the secondary voltage to the
primary voltage. It is denoted by K.
As (E2 ∞ N2 and E1 ∞ N1)

Basic Construction of Transformer
Basically a transformer consists of two inductive windings and a laminated steel core. The coils
are insulated from each other as well as from the steel core. A transformer may also consist of a
container for winding and core assembly (called as tank), suitable bushings to take our the
terminals, oil conservator to provide oil in the transformer tank for cooling purposes etc. The
figure at left illustrates the basic construction of a transformer.
In all types of transformers, core is constructed by assembling (stacking) laminated sheets of

steel, with minimum air-gap between them (to achieve continuous magnetic path). The steel
used is having high silicon content and sometimes heat treated, to provide high permeability
and low hysteresis loss. Laminated sheets of steel are used to reduce eddy current loss. The
sheets are cut in the shape as E,I and L. To avoid high reluctance at joints, laminations are
stacked by alternating the sides of joint. That is, if joints of first sheet assembly are at front face,
the joints of following assemble are kept at back face.
Types of Transformers
Transformers can be classified on different basis, like types of construction, types of cooling etc.
(A) On the basis of construction, transformers can be classified into two types as; (i) Core
type transformer and (ii) Shell type transformer, which are described below.
(I) Core Type Transformer
In core type transformer, windings are cylindrical former wound, mounted on the core limbs as
shown in the figure above. The cylindrical coils have different layers and each layer is insulated
from each other. Materials like paper, cloth or mica can be used for insulation. Low voltage
windings are placed nearer to the core, as they are easier to insulate.
(Ii) Shell Type Transformer
The coils are former wound and mounted in layers stacked with insulation between them. A
shell type transformer may have simple rectangular form (as shown in above fig), or it may have
a distributed form.
(B) On the basis of their purpose
1. Step up transformer: Voltage increases (with subsequent decrease in current) at

secondary.
2. Step down transformer: Voltage decreases (with subsequent increase in current) at
secondary.
(C) On the basis of type of supply
1. Single phase transformer

2. Three phase transformer
(D) On the basis of their use
1. Power transformer: Used in transmission network, high rating

2. Distribution transformer: Used in distribution network, comparatively lower rating than that
of power transformers.
3. Instrument transformer: Used in relay and protection purpose in different instruments in
industries
 Current transformer (CT)
 Potential transformer (PT)
(E) On the basis of cooling employed
1. Oil-filled self-cooled type

2. Oil-filled water cooled type
3. Air blast type (air cooled)

Working Principle of Transformer

Uploaded by

Copyright:

Available Formats

Working Principle of Transformer

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Working Principle of Transformer

Uploaded by

Copyright:

Available Formats

How does a transformer work?

What are the different types of transformers?

Working Principle of Transformer

According to Ohm’s Law

It is defined as the ratio of primary to secondary turns.

If N2 > N1 the transformer is called Step up transformer

If N2 < N1 the transformer is called Step down transformer

As (E2 ∞ N2 and E1 ∞ N1)

In all types of transformers, core is constructed by assembling (stacking) laminated sheets of

(Ii) Shell Type Transformer

(B) On the basis of their purpose

1. Step up transformer: Voltage increases (with subsequent decrease in current) at

(C) On the basis of type of supply

1. Single phase transformer

(D) On the basis of their use

1. Power transformer: Used in transmission network, high rating

(E) On the basis of cooling employed

1. Oil-filled self-cooled type

You might also like