Xilanh SMC PDF

Air Cylinder
MB Series
ø32, ø40, ø50, ø63, ø80, ø100, ø125 RoHS
10% lighter
CJ1
(ø40-100 stroke)
CJP
Weight CJ2
JCM
CM2
MB Series Current model CM3
0.91 kg 1.01 kg
CG1
CG3
JMB
Reduced weight by MB
MB1
changing the shape of
CA2
the rod cover and
CS1
head cover.
CS2
D-
-X
Technical
Data
387
Double acting, Single rod MB Series ø32, ø40, ø50, ø63, ø80, ø100, ø125
Part numbers with rod end bracket and/or pivot bracket available
Not necessary to order a bracket for the applicable cylinder separately
Note) Mounting bracket is shipped together with the product, but not assembled.
Example) MDB D -40-100Z- N V -M9BW

Mounting type
Pivot bracket Double clevis Center trunnion Rod end bracket With rod end bracket
Nil No bracket Nil No bracket V: Single knuckle W: Double
joint knuckle joint
Pivot bracket is V Single knuckle joint
shipped together
N W Double knuckle joint
with the product,
but not assembled.
∗ Applicable to only D (Double
clevis) and T (Center trunnion)
mounting types.
Various mounting bracket options

N: Double clevis pivot bracket
• Suitable mounting brackets can be selected
for the installation condition.
• Improved amount of mounting freedom D: Double clevis
C: Single clevis
G: Head flange
B: Basic
L: Axial foot
V: Single knuckle joint
N: Trunnion pivot bracket
W: Double knuckle joint
F: Rod flange
L: Axial foot
T: Center trunnion
N: Trunnion pivot bracket
388
Air Cylinder
Lightweight Applicable speed/load
Reduced weight by changing the shape of the rod  Piston speed: Max. 1000 mm/s (ø32 to ø125)
cover and head cover.  Load yield: See table below.
[kg] [kg]
Bore size [mm] MB Reduction rate [%] Current model Bore size [mm] Maximum load mass
32 0.66 8 0.72 32 80
40 0.91 10 1.01 40 140
Port
50 1.56 9 1.71 50 190 CJ1
63 1.83 9 2.01 63 310
80 3.25 9 3.57 80 500 CJP
100 4.48 7 4.82 100 800
125 6.90 0 6.90 125 1300
CJ2
∗ At 100 stroke ∗ Speed: 200 mm/s
JCM
CM2
CM3
CG1
CG3
Various switches such as compact auto
JMB
switches and magnetic field resistant
auto switches can be mounted. MB
Compact auto switches MB1

· D-M9 CA2
No environmental hazardous · D-A9
Mounting dimensions are substances used CS1
the same as the current Lead free bushing is used Magnetic field resistant
as sliding material. Compli-
auto switches CS2
product. · D-P3DWA
ant with EU RoHS directive.
· D-P4DW
Series Variations
Bore size [mm] Built-in With
Series Type Cushion Page
32 40 50 63 80 100 125 magnet rod boot
Standard Rubber
Double acting,
Single rod 392
Single rod
MB-Z Air
Standard Rubber
Double acting,
Double rod 402
Double rod
MBW-Z Air
Non-rotating rod Rubber

Double acting,
Single rod 408
Single rod
MBK-Z Air
Non-rotating rod Rubber

Double acting,
Double rod 412
Double rod
MBKW-Z Air
With end lock Rubber

Double acting,
MBB Single rod 416
Air
Smooth Cylinder Double acting, Best Pneumatics

MBY-Z Single rod
Rubber
No.w-3 D-
Use the new series “Smooth Cylinder MBY Series” -X

Low friction
to realize bi-directional low friction and low-speed operation.
MBQ Technical
(Refer to the Best Pneumatics No.w-3.) Data
389 A
Combinations of Standard and Made to Order Specifications
MB Series
Series MB-Z
(Standard type)
V : Standard Action/ Double acting
: Made to Order Type
v : Special product (Please contact SMC for details.) Single rod Double rod
Cushion
— : Not available Air Rubber Air Rubber
Page
392 402
Symbol Specifications Applicable ø32 to ø100 ø125 ø32 to ø100 ø125 ø32 to ø100 ø125 ø32 to ø100 ø125
bore size
Standard Standard V V V V V V V V
Long st Long stroke V V V V V V V V
ø32 to ø125
D Built-in magnet V V V V V V V V
MBl-lJK With rod boot V V V V V V V V
25A Copper (Cu) and Zinc (Zn)-free Note 1) ø32 to ø100 V v v v v v v v
MBlRV Water resistant V v V v V v V v
10- Clean series Note 6) ø32 to ø125 v v v v v v v v
20- Copper Note 5) and Fluorine-free Note 6) —Note 9) —Note 9) —Note 9) —Note 9) —Note 9) —Note 9) —Note 9) —Note 9)
XAl Change of rod end shape
XB5 Oversized rod cylinder Note 6) v v v v v v v

XB6 Heat resistant cylinder (−10 to 150°C) v v v v v
XB13 Low speed cylinder (5 to 50 mm/s) Note 6) v v v v v v
XC3 Special port location Note 6) Note 7) v v v v
XC4 With heavy duty scraper v v v v
XC5 Heat resistant cylinder (−10 to 110°C) v v v v v
XC6 Made of stainless steel — — — —
ø32 to ø125
XC7 Tie-rod, cushion valve, tie-rod nut, etc. made of stainless steel v v v v
XC8 Adjustable stroke cylinder/Adjustable extension type v v — — — —
XC9 Adjustable stroke cylinder/Adjustable retraction type v v — — — —
XC10 Dual stroke cylinder/Double rod type v v — — — —
XC11 Dual stroke cylinder/Single rod type v v — — — —
XC12 Tandem cylinder v v v v v v
XC14 Change of trunnion bracket mounting position
XC22 Fluororubber seal v v v v v

XC26 With split pins for double clevis pin/double knuckle joint pin and flat washers ø125 — — — — — —
XC27 Double clevis and double knuckle joint pins made of stainless steel — — — —
XC29 Double knuckle joint with spring pin v v v v v v
XC30 Rod trunnion v v v v
XC35 With coil scraper v v v v
XC65 Made of stainless steel (Combination of XC7 and XC68) v v v v v
ø32 to ø125
XC68 Made of stainless steel (with hard chrome plated piston rod) v v v v
XC88 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: Stainless steel 304) v v v v
XC89 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: S45C) v v v v
XC91 Spatter resistant coil scraper, Grease for welding (Piston rod: S45C) v v v v
X1184 Cylinder with heat resistant reed auto switch (−10 to 120°C) v v v v v v v
Note 1) For details, refer to the Web Catalog.
Note 2) For details about the smooth cylinder, refer to the Best Pneumatics No.w-3.
Note 3) Simple specials except XC14A and XC14B.
Note 4) XC10 specification for the MBK-Z series is the non-rotating type on both sides. For only one side, submit a special order request form.
Note 5) Copper-free for the externally exposed part. For details, refer to the Web Catalog.
A 390
MB Series
Use the new series “Smooth Cylinder MBY Series”
to realize bi-directional low friction and low-speed operation.
(Refer to the Best Pneumatics No.w-3.)
MBK-Z MBB Note 6) MBY-Z Note 2) MBlQ Note 6)

(Non-rotating rod type) (With end lock) (Smooth Cylinder) (Low friction type)
Double acting
CJ1
Single rod Double rod Single rod Single rod Single rod
Air Rubber Air Rubber Air — Note 9) — CJP
408 412 416 Best Pneumatics No.w-3 424
ø32 to ø100 Symbol CJ2

V V V V V V V Standard JCM
v v v v v v v Long st
V V V V V V V D
CM2
V V V V V v v MBl-lJK CM3
— — — — v — — 25A
CG1
— — — — v — v MBlRV
v v v v v — v 10- CG3
— — — — v — — 20-
JMB
v v XAl
v v v v v v v XB5 MB
v v v v v — — XB6
MB1
v v v v v — — XB13
v v XC3 CA2
— — — — v — — XC4
CS1
v v v v v — — XC5
vNote 8) vNote 8) v v v — XC6 CS2
v XC7
— — v v v XC8
— — v v v XC9
Note 4) Note 4)
— — v v XC10
v v — — v v v XC11
v v v v v — — XC12
v v Note 3)
XC14
v v v v v — — XC22
— — — — — — — XC26
v v XC27
v v v v XC29
XC30
— — — — v — v XC35
— — — — v XC65
— — — — — — XC68
— — — — — — — XC88
— — — — — — — XC89
— — — — — — — XC91
v v v v v — — X1184
D-
Note 6) The cover shape is the same as the current product.
Note 7) The XC3BB, XC3CC and XC3DD with trunnion bracket are available with new models (part numbers with “Z”).
-X
Note 8) The piston rod of the MBK-Z series is made of stainless steel. The rod end nut made of stainless steel is available with X1292.
Note 9) The copper and fluorine-free specification is available as a standard product. Technical
Data
391 A
Air Cylinder: Standard Type
Double Acting, Single Rod
MB Series
ø32, ø40, ø50, ø63, ø80, ø100, ø125
RoHS
How to Order
MB B 32 50 Z
With auto switch MDB B 32 50 Z M9BW
With auto switch
(Built-in magnet) Number of auto
Bore size Accessories 1 Auto switch switches
Mounting type 32 32 mm Nil No bracket
Nil Without auto switch Nil 2 pcs.
40 40 mm N Pivot bracket
B Basic ∗ For applicable auto switches, S 1 pc.
50 50 mm ∗ Only for D and T mounting types.
L Axial foot ∗ Pivot bracket is shipped together with the product.
refer to the table below. 3 3 pcs.
F Rod flange 63 63 mm ∗ For details, refer to page 400. n “n” pcs.
G Head flange 80 80 mm
100 100 mm Suffix (Cushion) Made to Order
C Single clevis
D Double clevis 125 125 mm Nil Air cushion For details, refer to page 393.
T Center trunnion N∗ Rubber bumper
∗ Trunnion type is mounted before shipment. ∗ Since the bumpers are attached to the both Accessories 2
∗ Other mounting brackets ø32 to ø100: Shipped together. sides of the piston for rubber bumper type, the Nil No bracket
overall length is longer than the cylinder with air
ø125: Assembled before shipment.
cushion as follows: ø32, ø40: +6 mm, ø50, ø63: V Single knuckle joint
+8 mm, ø80, ø100: +10 mm, ø125: +12 mm. W Double knuckle joint
∗ A knuckle joint pin is not provided with the single
Port thread type Suffix (Rod boot) knuckle joint.
Nil Rc Cylinder stroke [mm] Nil None ∗ Rod end bracket is shipped together with the product.
TN NPT
Refer to “Standard Strokes” J Nylon tarpaulin
TF G on page 393. K Heat resistant tarpaulin ∗ Refer to “Ordering Example of Cylinder Assembly” on page 393.
Applicable Auto Switches/Refer to the pages 1575 to 1701 for further information on auto switches.
Load voltage Auto switch model Lead wire length [m]
Indicator light
Electrical Wiring Pre-wired Applicable

Type Special function Tie-rod Band 0.5 1 3 5
entry (Output) DC AC connector load
mounting mounting (Nil) (M) (L) (Z)
3-wire (NPN) M9N — V V V v v IC
5 V, 12 V
Grommet 3-wire (PNP) 24 V — M9P — V V V v v circuit
— 2-wire 12 V M9B — V V V v v
Terminal 3-wire (NPN) 5 V, 12 V — G39 — — — — — —
Solid state auto switch
conduit 2-wire 12 V — K39 — — — — —

3-wire (NPN) M9NW — V V V v v IC
Diagnostic indication 5 V, 12 V
(2-color indicator)
3-wire (PNP) M9PW — V V V v v circuit Relay,
Yes
2-wire 12 V M9BW — V V V v v — PLC
3-wire (NPN) 24 V — M9NA∗1 — v v V v v IC
Water resistant 5 V, 12 V
(2-color indicator)
Grommet 3-wire (PNP) M9PA∗1 — v v V v v circuit
2-wire 12 V M9BA∗1 — v v V v v —
With diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V F59F — V — V v v IC circuit
Magnetic field resistant 2-wire P3DWA — V — V V v
— —
(2-color indicator) (Non-polar) P4DW — — — V V v
3-wire (NPN equivalent) — 5V — A96 — V — V — — IC circuit —
Yes
100 V A93 — V V V V — —
Reed auto switch
Grommet No 100 V or less A90 — V — V — — IC circuit

Relay,
Yes 100 V, 200 V A54 — V — V V —
PLC
—
No 12 V 200 V or less A64 — V — V — —
2-wire 24 V
Terminal — — A33 — — — — —
—
conduit — A34 — — — — — PLC
Yes 100 V, 200 V
DIN terminal — A44 — — — — — Relay,
Diagnostic indication (2-color indicator) Grommet — — A59W — V —  — — PLC
∗1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance.
A water resistant type cylinder is recommended for use in an environment which requires water resistance.
∗ Lead wire length symbols: 0.5 m·················· Nil (Example) M9NW 3 m·················· L (Example) M9NWL
1 m·················· M (Example) M9NWM 5 m·················· Z (Example) M9NWZ
∗ Solid state auto switches marked with “” are produced upon receipt of order.
∗ Since there are other applicable auto switches than listed above, refer to page 432 for details.
∗ The D-A9l/M9l/P3DWAl auto switches are shipped together, (but not assembled). (However, auto switch mounting brackets are assembled for the D-A9l/M9l
before shipment.)
A 392
Double Acting, Single Rod MB Series
Specifications
Bore size [mm] 32 40 50 63 80 100 125

Action Double acting, Single rod
Fluid Air
Proof pressure 1.5 MPa CJ1
Maximum operating pressure 1.0 MPa
Minimum operating pressure 0.05 MPa CJP
Symbol Ambient and fluid Without auto switch: –10 to 70°C
Double acting temperature With auto switch: –10 to 60°C
(No freezing) CJ2
Lubricant Not required (Non-lube)
JCM
Piston speed 50 to 1000 mm/s
Stroke length tolerance Up to 250: +1.0
0 , 251 to 1000: +1.4
0 , 1001 to 1500: +1.8
0 , 1501 to 2000: +2.2
0 CM2
Cushion Air cushion or Rubber bumper
Made to Order: Individual Specifications Port size (Rc) 1/8 1/4 3/8 1/2 CM3
(For details, refer to page 433.) Basic, Axial foot, Rod flange, Head flange
Symbol Specifications
Mounting
Single clevis, Double clevis, Center trunnion CG1
-X1184 Cylinder with heat resistant reed auto switch (−10 to 120°C)
CG3
Made to Order Standard Strokes
Click here for details
[mm]
JMB
Max.
-XA Change of rod end shape
Bore Standard stroke
manufacturable MB
size Stroke range q Stroke range w stroke
-XB5 Oversized rod cylinder*1 *2 *3
-XB6 Heat resistant cylinder (−10 to 150°C)
32 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500 Up to 1000 MB1
-XC3 Special port location*3 40 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500
-XC4 With heavy duty scraper 50 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600 CA2
Up to
-XC5 Heat resistant cylinder (−10 to 110°C) 63 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600 Up to 1800
-XC6 Made of stainless steel*4 80 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800
2700
CS1
-XC7 Tie-rod, cushion valve, tie-rod nut, etc. made of stainless steel 100 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800
-XC8 Adjustable stroke cylinder/Adjustable extension type CS2
125 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000 Up to 2000
-XC9 Adjustable stroke cylinder/Adjustable retraction type
Note 1) Manufacture of intermediate strokes is possible. (Spacers are not used.)
-XC10 Dual stroke cylinder/Double rod type Note 2) Applicable strokes should be confirmed according to the usage. For details, refer to “Air Cylinders
-XC11 Dual stroke cylinder/Single rod type Model Selection” on front matter pages. In addition, the products that exceed the stroke range q might
not be able to fulfill the specifications due to the deflection etc.
-XC12 Tandem cylinder
Note 3) Please consult with SMC for manufacturability and the part numbers when exceeding the stroke range w.
-XC14 Change of trunnion bracket mounting position Note 4) The stroke range with rod boot is up to 1000 mm. Please consult with SMC when exceeding 1000 mm strokes.
-XC22 Fluororubber seal
With split pins for double clevis pin/double
-XC26 knuckle joint pin and flat washers*4
Double clevis and double knuckle joint

Ordering Example of Cylinder Assembly
-XC27 pins made of stainless steel
-XC29 Double knuckle joint with spring pin Cylinder model: MDBD32-50Z-NW-M9BW
-XC30 Rod trunnion
-XC35 With coil scraper Double clevis
Mounting D: Double clevis
-XC65 Made of stainless steel (Combination of XC7 and XC68)*2 Pivot bracket N: Yes
-XC68 Made of stainless steel (with hard chrome plated piston rod)*2 Rod end bracket W: Double knuckle joint
Auto switch D-M9BW: 2 pcs.
-XC88 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: Stainless steel 304)
-XC89 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: S45C) * Pivot bracket, double knuckle joint and auto
-XC91 Spatter resistant coil scraper, Grease for welding (Piston rod: S45C) switch are shipped together with the product,
but not assembled.
Pivot bracket
*1 Air cushion only
*2 Except ø125
Auto switch
*3 The cover shape is the same as the current product.
*4 ø125 only
Double knuckle joint
For special port location (-XC3), the mounting
bracket and port location can be determined using
the standard product corresponding to the operating
conditions. Also, this is only applicable to -XC3BB,
-XC3CC and -XC3DD with trunnion bracket.
Refer to pages 425 to 432 for cylinders with auto switches.
D-
• Auto switch proper mounting position (detection at stroke end) and its mounting height
For parts made of stainless steel (-XC6), use the • Minimum stroke for auto switch mounting -X
same specification stainless steel with the surface
• Auto switch mounting brackets/Part no.
treatment (with hard chrome plated piston rod) Technical
• Operating range
(-XC68). Data
393 B
MB Series
Accessories Rod Boot Material
Axial Rod Head Single Double Center Symbol Material Max. ambient temp.
Mounting Basic
foot flange flange clevis clevis trunnion J Nylon tarpaulin 70°C
Rod end nut        K Heat resistant tarpaulin 110°C∗
Standard
Clevis pin — — — — —  — ∗ Max. ambient temperature for rod boot itself.
Single knuckle joint       
Option       
(with pin)
Rod boot       
∗ Refer to page 401 for dimensions and part numbers. (Refer to page 396 for rod boot.)
Mounting Brackets/Part No. Allowable Kinetic Energy

2000
Bore size ø125
[mm]
32 40 50 63 80 100 125
1000 ø100
Axial foot Note 1) MB-L03 MB-L04 MB-L05 MB-L06 MB-L08 MB-L10 MB-L12
ø80
500
Rod/Head flange MB-F03 MB-F04 MB-F05 MB-F06 MB-F08 MB-F10 MB-F12
400 ø63
Single clevis MB-C03 MB-C04 MB-C05 MB-C06 MB-C08 MB-C10 MB-C12 300
Double clevis MB-D03 MB-D04 MB-D05 MB-D06 MB-D08 MB-D10 MB-D12 200 ø50
ø40
Note 1) Order two foots per cylinder.
Note 2) Accessories for each mounting bracket are as follows. 100
ø32
Load mass [kg]

Axial foot, Rod/Head flange, Single clevis/Body mounting bolt; Double clevis/Body mounting 80
bolt, Clevis pin, Flat washers and Split pins. → Refer to page 401 for details. 50
40
30
Theoretical Force 20
(Unit: N) OUT IN 10
Bore size Rod diameter Operating Piston area Operating pressure [MPa]
5
[mm] [mm] direction [mm2] 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 4
OUT 804 161 241 322 402 482 563 643 724 804 3
32 12
IN 691 138 207 276 346 415 484 553 622 691 2
OUT 1257 251 377 503 629 754 880 1006 1131 1257
40 16 1
IN 1056 211 317 422 528 634 739 845 950 1056
50
0
0
0
00
OUT 1963 393 589 785 982 1178 1374 1570 1767 1963
10
20
30
40
50
10
50 20
IN 1649 330 495 660 825 989 1154 1319 1484 1649 Maximum speed [mm/s]
OUT 3117 623 935 1247 1559 1870 2182 2494 2805 3117
63 20 Example) Load limit at rod end when the air cylinder
IN 2803 561 841 1121 1402 1682 1962 2242 2523 2803 ø63 is actuated at 500 mm/s.
OUT 5027 1005 1508 2011 2514 3016 3519 4022 4524 5027 Extend upward from 500 mm/s on the
80 25 horizontal axis of the graph to the
IN 4536 907 1361 1814 2268 2722 3175 3629 4082 4536
intersection point with the line for a tube
OUT 7854 1571 2356 3142 3927 4712 5498 6283 7069 7854 bore size of 63 mm, and then extend
100 30
IN 7147 1429 2144 2859 3574 4288 5003 5718 6432 7147 leftward from this point to find the load of
OUT 12272 2454 3682 4909 6136 7363 8590 9818 11045 12272 80 kg.
125 32
IN 11468 2294 3440 4588 5734 6881 8028 9174 10321 11468
Note) Theoretical force [N] = Pressure [MPa] x Piston area [mm2]
Weights
[kg]
Bore size [mm] 32 40 50 63 80 100 125
Basic 0.44 0.59 1.04 1.29 2.41 3.36 5.48
Axial foot 0.56 0.73 1.26 1.57 2.91 4.02 7.56
Rod/Head flange 0.73 0.96 1.49 2.08 3.86 6.67 9.64
Basic weight
Single clevis 0.69 0.82 1.38 1.92 3.52 6.53 8.05
Double clevis 0.7 0.86 1.47 2.08 3.81 7.05 8.25 Calculation
Center trunnion 0.73 0.95 1.52 2.09 3.96 7.03 8.46 Example) MBB32-100Z (Basic, ø32, 100 stroke)
Additional weight per 50 mm of stroke All mounting brackets 0.11 0.16 0.26 0.27 0.42 0.56 0.71 • Basic weight ······················· 0.44 (Basic, ø32)
• Additional weight ················ 0.11/50 stroke
Single knuckle joint 0.15 0.23 0.26 0.26 0.60 0.83 1.08 • Cylinder stroke ··················· 100 stroke
Accessories
Double knuckle joint (with pin) 0.22 0.37 0.43 0.43 0.87 1.27 1.58 0.44 + 0.11 x 100/50 = 0.66 kg
394
Construction
!9 !4 i q !2 !6 !1 e r y !5 @0 !3 t !8 u w o !0 !7
CJ1
CJP
CJ2
JCM
CM2
CM3
CG1
CG3
JMB
MB125 MB
MB1
Component Parts
No. Description Material Q’ty Note No. Description Material Q’ty Note CA2
1 Rod cover Aluminum die-cast 1 Trivalent chromated 11 Tie-rod Carbon steel 4 Trivalent zinc chromated
2 Head cover Aluminum die-cast 1 Trivalent chromated 12 Tie-rod nut Carbon steel 8 Trivalent zinc chromated CS1
3 Cylinder tube Aluminum alloy 1 Hard anodized 13 Wear ring Resin 1
4 Piston rod Carbon steel 1 Hard chrome plating 14 Rod seal NBR 1 CS2
5 Piston Aluminum alloy 1 15 Piston seal NBR 1
6 Cushion ring Aluminum alloy 1 Anodized 16 Cushion seal Urethane 2
7 Cushion ring B Aluminum alloy 1 Anodized 17 Cushion valve seal NBR 2
8 Bushing Bearing alloy 1 18 Cylinder tube gasket NBR 2
9 Cushion valve Steel wire 2 Trivalent zinc chromated 19 Rod end nut Rolled steel 1 Trivalent zinc chromated
10 Retaining ring Steel for spring 2 ø40 to ø125 20 Magnet — (1)
Replacement Parts/Seal Kit

Bore size
Kit no. Contents
[mm]
32 MB32Z−PS
40 CA2−40Z−PS
50 CA2−50Z−PS
Set of the nos.
63 CA2−63Z−PS
!4, !5, !6, !8
80 CA2−80Z−PS
100 CA2−100Z−PS
125 MB125−PS
∗ Seal kits consist of items !4 , !5, !6, !8 , and can be ordered by
using the seal kit number corresponding to each bore size.
∗ Center trunnion type should not be disassembled. (Refer to page 434.)
∗ The seal kit includes a grease pack (10 g for ø32 to ø50, 20 g for
ø63 and ø80, 30 g for ø100 and ø125).
Order with the following part number when only the grease pack is needed.
Grease pack part number: GR-S-010 (10 g), GR-S-020 (20 g)
Water Resistant Air Cylinder

D-
Water resistant air cylinders are also available in the MB series, which are
suitable for use on machine tools, where exposure to coolant is possible
and applicable for food machinery and automobile washing equipment in -X
an environment where water splashes. Please refer to page 1125 for more
Technical
information.
Data
395
MB Series
Standard
Basic: (B) When the stroke is 2201 mm or longer, Cushion valve W V Port
2 x Rc P a tie-rod reinforcement ring is attached.
G G
Width across flats KA øE
TX
øD
øE
C
B
MM H1
Width across flats B1 AL MB N C
MA 2x4xJ B
A K F N TT TY
H S + Stroke
ZZ + Stroke
With rod boot

ød
øe
10.2 10.2
l f
h
[mm]
Bore size
[mm]
A AL B B1 C D E F G H H1 J K KA MA MB MM N P S TT TX TY V W ZZ
32 22 19.5 46 17 32.5 12 30 13 13 47 6 M6 x 1 6 10 16 4 M10 x 1.25 27 1/8 84 17 48 49 4 6.5 135
40 30 27 52 22 38 16 35 13 14 51 8 M6 x 1 6 14 16 4 M14 x 1.5 27 1/4 84 22 55 58 4 9 139
50 35 32 65 27 46.5 20 40 14 15.5 58 11 M8 x 1.25 7 18 16 5 M18 x 1.5 31.5 1/4 94 22 68 71 5 10.5 156
63 35 32 75 27 56.5 20 45 14 16.5 58 11 M8 x 1.25 7 18 16 5 M18 x 1.5 31.5 3/8 94 28 81 81 9 12 156
80 40 37 95 32 72 25 45 20 19 72 13 M10 x 1.5 10 22 16 5 M22 x 1.5 38 3/8 114 34 102 102 11.5 14 190
100 40 37 114 41 89 30 55 20 19 72 16 M10 x 1.5 10 26 16 5 M26 x 1.5 38 1/2 114 40 124 124 17 15 190
125 54 50 136 41 110 32 60 27 19 97 16 M12 x 1.75 13 27 20 6 M27 x 2 38 1/2 120 50 148 148 17 15 223
With Rod Boot [mm]

Bore size l
[mm]
d e f
1 to 50 51 to 100 101 to 150 151 to 200 201 to 300 301 to 400 401 to 500 501 to 600 601 to 700 701 to 800 801 to 900 901 to 1000
32 54 36 23 12.5 25 37.5 50 75 100 125 — — — — —
40 56 41 23 12.5 25 37.5 50 75 100 125 — — — — —
50 64 51 25 12.5 25 37.5 50 75 100 125 150 — — — —
63 64 51 25 12.5 25 37.5 50 75 100 125 150 — — — —
80 68 56 29 12.5 25 37.5 50 75 100 125 150 175 200 — —
100 76 61 29 12.5 25 37.5 50 75 100 125 150 175 200 — —
125 82 75 27 10 20 30 40 60 80 100 120 140 160 180 200
[mm] Rubber Bumper

Bore size h Bore size
[mm] [mm]
S ZZ
1 to 50 51 to 100 101 to 150 151 to 200 201 to 300 301 to 400 401 to 500 501 to 600 601 to 700 701 to 800 801 to 900 901 to 1000
32 73 86 98 111 136 161 186 — — — — — 32 90 141
40 81 94 106 119 144 169 194 — — — — — 40 90 145
50 89 102 114 127 152 177 202 227 — — — — 50 102 164
63 89 102 114 127 152 177 202 227 — — — — 63 102 164
80 101 114 126 139 164 189 214 239 264 289 — — 80 124 200
100 101 114 126 139 164 189 214 239 264 289 — — 100 124 200
125 120 130 140 150 170 190 210 230 250 270 290 310 125 132 235
∗ Model without air cushion is designed to include rubber bumpers. Since the bumpers are attached to the both sides of the piston, the overall
length is longer than the cylinder with air cushion as follows: ø32, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø100: +10 mm, ø125: +12 mm
A 396
Standard/With Mounting Bracket ∗ Refer to Basic (B) for other dimensions.
Axial foot: (L)

When the stroke is 2201 mm or longer, Cushion valve Port
a tie-rod reinforcement ring is attached. TY
CJ1
CJP
TX
LY
4 x øLD
CJ2
LH
JCM
LT
X TT X
Y LS + Stroke Y LX CM2
ZZ + Stroke LZ
CM3
[mm] Rubber Bumper
Bore size Bore size
CG1
[mm]
LD LH LS LT LX LY LZ TT TX TY X Y ZZ [mm]
LS ZZ
32 7 30 128 3.2 32 53 50 17 48 49 22 9 162 32 134 168 CG3
40 9 33 132 3.2 38 59 55 22 55 58 24 11 170 40 138 176
50 9 40 148 3.2 46 72.5 70 22 68 71 27 11 190 50 156 198 JMB
63 12 45 148 3.6 56 82.5 80 28 81 81 27 14 193 63 156 201
80 12 55 174 4.5 72 102.5 100 34 102 102 30 14 230 80 184 240 MB
100 14 65 178 4.5 89 122 120 40 124 124 32 16 234 100 188 244
125 14 81 210 8 90 149 136 50 148 148 45 20 282 125 222 294 MB1
∗ Model without air cushion is designed to include rubber bumpers.

CA2
Since the bumpers are attached to the both sides of the piston, the overall
length is longer than the cylinder with air cushion as follows: ø32, ø40: +6 mm, CS1
ø50, ø63: +8 mm, ø80, ø100: +10 mm, ø125: +12 mm
CS2
Rod flange: (F)
Cushion valve Port 4 x øFD
When the stroke is 2201 mm or longer,
FE FT a tie-rod reinforcement ring is attached.
øFd
FB
TX
FY
TT TY
FX
FZ
[mm]
Bore size
[mm]
FB FD FE FT FX FY FZ Fd TT TX TY
32 50 7 3 10 64 32 79 24.5 17 48 49
40 55 9 3 10 72 36 90 29.5 22 55 58
50 70 9 2 12 90 45 110 35.5 22 68 71
63 80 9 2 12 100 50 120 38.5 28 81 81
80 100 12 4 16 126 63 153 41 34 102 102
100 120 14 4 16 150 75 178 46 40 124 124
125 138 14 7 20 180 102 216 57 50 148 148
D-
Since the bumpers are attached to the both sides of the piston, the overall -X
length is longer than the cylinder with air cushion as follows: ø32, ø40: +6 mm,
ø50, ø63: +8 mm, ø80, ø100: +10 mm, ø125: +12 mm Technical
Data
397 A
MB Series
Head flange: (G)

When the stroke is 2201 mm or longer, Cushion valve Port 4 x øFD
a tie-rod reinforcement ring is attached.
FB
TX
FY
TT FT TY
ZZ + Stroke FX
FZ
[mm] Rubber Bumper
Bore size Bore size
[mm]
FB FD FT FX FY FZ TT TX TY ZZ [mm]
ZZ
32 50 7 10 64 32 79 17 48 49 141 32 147
40 55 9 10 72 36 90 22 55 58 145 40 151
50 70 9 12 90 45 110 22 68 71 164 50 172
63 80 9 12 100 50 120 28 81 81 164 63 172
80 100 12 16 126 63 153 34 102 102 202 80 212
100 120 14 16 150 75 178 40 124 124 202 100 212
125 138 14 20 180 102 216 50 148 148 237 125 249

ø50, ø63: +8 mm, ø80, ø100: +10 mm, ø125: +12 mm
Single clevis: (C)

When the stroke is 2201 mm or longer,
a tie-rod reinforcement ring is attached. Cushion valve Port
CDH10
TX
U CX
TT L TY
Z + Stroke RR
ZZ + Stroke
[mm] Rubber Bumper

Bore size Bore size
[mm]
CDH10 CX L RR TT TX TY U Z ZZ [mm]
Z ZZ
32 10+0.058
0 14−0.1
−0.3 23 10.5 17 48 49 13 154 164.5 32 160 170.5
40 10+0.058
0 14−0.1
−0.3 23 11 22 55 58 13 158 169 40 164 175
50 +0.070
14 0 20−0.1
−0.3 30 15 22 68 71 17 182 197 50 190 205
63 +0.070
14 0 20−0.1
−0.3 30 15 28 81 81 17 182 197 63 190 205
80 22+0.084
0 30−0.1
−0.3 42 23 34 102 102 26 228 251 80 238 261
100 22+0.084
0 30−0.1
−0.3 42 23 40 124 124 26 228 251 100 238 261
125 +0.084
25 0 32−0.
−0.3 50 28 50 148 148 30 267 295 125 279 307

ø50, ø63: +8 mm, ø80, ø100: +10 mm, ø125: +12 mm
A 398
Double clevis: (D)

Cushion valve Port
Hole dia.: CDH10

Shaft dia.: CDd9 CJ1
CJP
TX
CJ2
U CX JCM
TT L CZ
Z + Stroke RR TY CM2
ZZ + Stroke
CM3
[mm] Rubber Bumper
Bore size Bore size
CG1
[mm]
CDH10 CDd9 CX CZ L RR TT TX TY U Z ZZ [mm]
Z ZZ
32 10+0.058
0 10–0.040
–0.076 14+0.3
+0.1 28 23 10.5 17 48 49 13 154 164.5 32 160 170.5
CG3
40 10+0.058 10–0.04 14+0.3 28 23 11 22 55 58 13 158 169 40 164 175
50
0
14+0.070
0
–0.076
14–0.050
–0.093
+0.1
20+0.3
+0.1 40 30 15 22 68 71 17 182 197 50 190 205
JMB
63 14+0.070 14–0.050 20+0.3 40 30 15 28 81 81 17 182 197 63 190 205
80
0
22+0.084
0
–0.093
22–0.065
–0.117
+0.1
30+0.3
+0.1 60 42 23 34 102 102 26 228 251 80 238 261
MB
100 22+0.084 22–0.065 30+0.3 60 42 23 40 124 124 26 228 251 100 238 261
125
0
25+0.084
0
–0.117
25–0.065
–0.117
+0.1
32+0.3
+0.1 64 50 28 50 148 148 30 267 295 125 279 307
MB1

CA2
length is longer than the cylinder with air cushion as follows: ø32, ø40: +6 mm, CS1
ø50, ø63: +8 mm, ø80, ø100: +10 mm, ø125: +12 mm
CS2
Center trunnion: (T)

Cushion valve Port
Z + 1/2 stroke
TY
TX
øTDe8
TT
TZ
[mm] Rubber Bumper
Bore size Bore size
[mm]
TDe8 TT TX TY TZ Z [mm]
Z
32 12–0.032
–0.059 17 50 49 74 89 32 92
40 16–0.032
–0.059 22 63 58 95 93 40 96
50 16–0.032
–0.059 22 75 71 107 105 50 109
63 20–0.040
–0.073 28 90 87 130 105 63 109
80 20–0.040
–0.073 34 110 110 150 129 80 134
100 25–0.040
–0.073 40 132 136 182 129 100 134
125 25–0.040 50 160 160 210 157 125 163
–0.073
D-
Since the bumpers are attached to the both sides of the piston, the “Z”
-X
dimension is longer than the cylinder with air cushion as follows: ø32, ø40: +3 Technical
mm, ø50, ø63: +4 mm, ø80, ø100: +5 mm, ø125: +6 mm Data
399
MB Series
Pivot Bracket/Trunnion and Double Clevis Pivot Bracket

Part No.
Bore size
Description
MBl32 MBl40 MBl50 MBl63 MBl80 MBl100 MBl125
Trunnion pivot bracket Note) MB-S03 MB-S04 MB-S06 MB-S10 MB-S12
Double clevis pivot bracket MB-B03 MB-B05 MB-B08 MB-B12
Note) Order 2 trunnion pivot brackets per cylinder.
Trunnion pivot bracket TE

Z + 1/2 stroke TO TX TO
TY
B
4 x øTT
TF
øTD
TH
TS
B
2 x øTR TC
TU TL TU
TA
[mm] Rubber Bumper
Bore size Bore size
Part no.
[mm]
B TA TL TU TC TX TE TO TR TT TS TH TF Z∗∗ TDH10 [mm]
Z
MB-S03 32 46 62 45 8.5 62 50 74 12 7 13 10 35 47 89 12+0.070
0 32 92
40 52 80 60 10 80 63 97 17 9 17 12 45 60 93 16+0.070
0 40 96
MB-S04
50 65 80 60 10 92 75 109 17 9 17 12 45 60 105 16+0.070
0 50 109
63 75 100 70 15 110 90 130 20 11 22 14 60 80 105 20+0.084
0 63 109
MB-S06
80 95 100 70 15 130 110 150 20 11 22 14 60 80 129 20+0.084
0 80 134
MB-S10 100 114 120 90 15 158 132 184 26 13.5 24 17 75 100 129 25+0.084
0 100 134
MB-S12 125 136 142 105 18.5 186 160 212 26 13.5 24 25 85 115 157 25+0.084
0 125 163
Double clevis pivot bracket B

Z + Stroke DB DX
DD
B°
°
90
4 x øDT
B
A°
DH
DS
4 x øDR DO DC DO
DE
DU DL DU
DA
[mm] Rubber Bumper
Bore size Bore size
Part no.
[mm]
B DA DB DL DU DC DX DE DO DR DT DS DH Z∗ DD H10 [mm]
Z
32 46 42 32 22 10 44 14 62 9 6.6 15 7 33 154 10+0.058
0 32 160
MB-B03
40 52 42 32 22 10 44 14 62 9 6.6 15 7 33 158 10+0.058
0 40 164
50 65 53 43 30 11.5 60 20 81 10.5 9 18 8 45 182 14+0.070
0 50 190
MB-B05
63 75 53 43 30 11.5 60 20 81 10.5 9 18 8 45 182 14+0.070
0 63 190
80 95 73 64 45 14 86 30 111 12.5 11 22 10 65 228 22+0.084
0 80 238
MB-B08
100 114 73 64 45 14 86 30 111 12.5 11 22 10 65 228 +0.084
22 0 100 238
MB-B12 125 136 90 78 60 15 110 32 136 13 13.5 24 14 75 267 25+0.084
0 125 279
Rotating Angle ∗∗ Model without air cushion is designed to include rubber bumpers.
Bore size Since the bumpers are attached to the both sides of the piston, the “Z” dimension is longer than the
[mm]
A° B° A° + B° + 90°
cylinder with air cushion as follows: ø32, ø40: +3 mm, ø50, ø63: +4 mm, ø80, ø100: +5 mm, ø125: +6
32, 40 25° 45° 160° mm
50, 63 40° 60° 190°
80, 100 30° 55° 175°
Since the bumpers are attached to the both sides of the piston, the overall length is longer than the
125 30° 50° 170° cylinder with air cushion as follows: ø32, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø100: +10 mm, ø125:
+12 mm
400
Dimensions of Accessories
Rod end nut 30° Knuckle joint pin
d
øDd9
(Standard) Clevis pin 2 x ød
C
m l
H B [mm]
L
[mm]
CJ1
Bore size Bore size [mm] d Applicable
Part no.
[mm]
d H B C D Part no.
Clevis Knuckle
Dd9 L l m
(Dril through) split pin CJP
NT-03 32 M10 x 1.25 6 17 19.6 16.5 CD-M03Note 1) 32, 40 10−0.040
−0.076 44 36 4 3 ø3 x 18 l
NT-04 40 M14 x 1.5 8 22 25.4 21 CD-M05Note 1) 50, 63 14−0.050
−0.093 60 51 4.5 4 ø4 x 25 l CJ2
NT-05 50, 63 M18 x 1.5 11 27 31.2 26 CD-M08Note 1) 80, 100 22−0.065
−0.117 82 72 5 4 ø4 x 35 l
NT-08 80 M22 x 1.5 13 32 37.0 31 IY-12Note 2) 125 25−0.065
−0.117 79.5 69.5 5 4 ø4 x 40 l JCM
NT-10 100 M26 x 1.5 16 41 47.3 39 Note 1) Split pins and flat washers are included. Note 2) Only pins are included when shipped.
NT-12M 125 M27 x 2 16 41 47.3 39
Y type CM2
MM NDH10 1 Double knuckle joint
I type RR CM3
R
45° MM øNDH10
R
1
Single knuckle joint
øE1
CG1
øE1
NX
NZ
A1 U1
L1
A NX U1
L1 CG3
[mm] [mm]
Part no.
Bore size
A A1 E1 L1 MM R1 U1 NDH10 NX Part no.
Bore size
E1 L 1 MM R1 U1 NDH10 NX NZ JMB
[mm] [mm]
I-03M 32 40 14 20 30 M10 x 1.25 12 16 10+0.058 14−0.10 Y-03MNote 1) 32 20 30 M10 x 1.25 10 16 10+0.058 14+0.30 28−0.10
I-04M 40 50 19 22 40 M14 x 1.5 12.5 19
0
10+0.058
0
−0.30
14−0.10
−0.30 Y-04MNote 1) 40 22 40 M14 x 1.5 11 19
0
10+0.058
0
+0.10
14+0.30
+0.10
−0.30
28−0.10
−0.30
MB
I-05M 50, 63 64 24 28 50 M18 x 1.5 16.5 24 14 0
+0.070
20−0.10 Y-05MNote 1) 50, 63 28 50 M18 x 1.5 14 24 14 0
+0.070
20+0.30 40−0.10
MB1
−0.30 +0.10 −0.30
I-08M 80 80 26 40 60 M22 x 1.5 23.5 34 22 0

+0.084
30−0.10
−0.30 Y-08MNote 1) 80 40 65 M22 x 1.5 20 34 22 0
+0.084
30+0.30
+0.10 60−0.10
−0.30
I-10M 100 80 26 40 60 M26 x 1.5 23.5 34 22+0.084

0 30−0.10
−0.30 Y-10MNote 1) 100 40 65 M26 x 1.5 20 34 22+0.084
0 30+0.30
+0.10 60−0.10
−0.30
I-12M 125 119 36 46 92 M27 x 2 28.5 34 25+0.084

0 32−0.10
−0.30 Y-12MNote 2) 125 46 100 M27 x 2 27 42 25+0.084
0 32+0.30
+0.10 64−0.10
−0.30 CA2
Note 1) A pin, split pins and flat washers are included. Note 2) A pin and split pins are included.
Bracket Combinations CS1
Bracket combination available …………………………………… Refer to the figure below. CS2

Bracket for
workpiece Single Double Clevis
Bracket Single clevis Double clevis
for cylinder knuckle joint knuckle joint pivot bracket
Single clevis — q — w —
Double clevis e — r — o
Single knuckle joint — t — y —
Double knuckle joint u — i — !0
No. Appearance No. Appearance

Single clevis + Double clevis Single knuckle joint + Double knuckle joint
q y
Single clevis + Double knuckle joint Double knuckle joint + Single clevis
w u
Double clevis + Single clevis Double knuckle joint + Single knuckle joint
e i
Double clevis + Single knuckle joint Double clevis + Clevis pivot bracket
r o
D-
Single knuckle joint + Double clevis Double knuckle joint + Clevis pivot bracket
t !0
-X
Technical
Data
401
Double Acting, Double Rod
MBW Series
ø32, ø40, ø50, ø63, ø80, ø100, ø125
RoHS
How to Order
MBW L 32 150 Z
With auto switch MDBW L 32 150 Z M9BW
With auto switch
(Built-in magnet) Number of auto switches
Nil 2 pcs.
Mounting type Auto switch S 1 pc.
B Basic Nil Without auto switch 3 3 pcs.
L Axial foot Bore size * For applicable auto switches, n “n” pcs.
F Rod flange refer to the table below.
32 32 mm Made to Order
T Center trunnion 40 40 mm Port thread For details, refer to page 403.
* Trunnion type is mounted 50 50 mm type
before shipment. Suffix (Cushion)
* Other mounting brackets
63 63 mm Nil Rc
ø32 to ø100: Shipped together. 80 80 mm TN NPT Nil Air cushion
ø125: Assembled before 100 100 mm TF G Suffix (Rod boot) N* Rubber bumper
shipment. 125 125 mm * Since the bumpers are attached to
Nil None
the both sides of the piston for
J Nylon tarpaulin (one end)
rubber bumper type, the overall
Cylinder stroke [mm] JJ Nylon tarpaulin (both ends) length is longer than the cylinder
Refer to “Standard Strokes” on page 403. K Heat resistant tarpaulin (one end) with air cushion as follows: ø32, ø40:
KK Heat resistant tarpaulin (both ends) +6 mm, ø50, ø63: +8 mm, ø80,
ø100: +10 mm, ø125: +12 mm.
Applicable Auto Switches/Refer to pages 1575 to 1701 for further information on auto switches.
Indicator light

Type Special function Tie-rod Band 0.5 1 3 5
entry (Output) DC AC connector load
3-wire (NPN) M9N — V   v v
5 V, 12 V IC circuit
Grommet 3-wire (PNP) 24 V — M9P —    v v
— 2-wire 12 V M9B —    v v
conduit 2-wire 12 V — K39 — — — — —

3-wire (NPN) M9NW —    v v
Diagnostic indication 5 V, 12 V IC circuit
(2-color indicator)
3-wire (PNP) M9PW —    v v Relay,
Yes
2-wire 12V M9BW —    v v — PLC
3-wire (NPN) 24 V — M9NA*1 — v v  v v
Water resistant 5 V, 12 V IC circuit
(2-color indicator)
Grommet 3-wire (PNP) M9PA*1 — v v  v v
2-wire 12 V M9BA*1 — v v  v v —
Diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V F59F —  —  v v IC circuit
Magnetic field resistant 2-wire P3DWA —  —   v
— —
(2-color indicator) (Non-polar) P4DW — — —   v
3-wire
— 5V — A96 —  —  — — IC circuit —
Yes (Equiv. to NPN)
    —
100 V — A93 —
Reed auto switch
Grommet
No  —  —
100 V or less
— IC circuit A90 —
Relay,
— Yes  —  
100 V, 200 V
— A54
PLC
—
No 12 V  —  —
200 V or less
— A64 —
2-wire 24 V
Terminal — A33 — — — ———
—
Yes 100 V, 200 V
Diagnostic indication (2-color indicator) Grommet — — A59W —  —  — — PLC
*1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance.
Please contact SMC regarding water resistant types with the above model numbers.
* Lead wire length symbols: 0.5 m·················· Nil (Example) M9NW 3 m·················· L (Example) M9NWL
1 m·················· M (Example) M9NWM 5 m·················· Z (Example) M9NWZ
* Solid state auto switches marked with “p” are produced upon receipt of order.
* Since there are other applicable auto switches than listed above, refer to page 432 for details.
* The D-A9l/M9l/P3DWAl auto switches are shipped together, (but not assembled). (However, auto switch mounting brackets are assembled for the D-A9l/M9l
before shipment.)
A 402
Double Acting, Double Rod MBW Series
Specifications
Bore size [mm] 32 40 50 63 80 100 125

Action Double acting, Double rod
Fluid Air
Max. operating pressure 1.0 MPa
Min. operating pressure 0.05 MPa CJP
Symbol Ambient and fluid Without auto switch: –10 to 70°C
(No freezing)
Double acting, Air cushion temperature With auto switch: –10 to 60°C CJ2
Lubrication Not required (Non-lube)
Operating piston speed 50 to 1000 mm/s 50 to 700 mm/s JCM
Allowable stroke tolerance Up to 250: +1.0 +1.4
0 , 251 to 1000: 0 , 1001 to 1500
Cushion Note) Air cushion or Rubber bumper CM2
Port size (Rc, NPT, G) 1/8 1/4 3/8 1/2
Made to Order Mounting Basic, Axial foot, Rod flange, Center trunnion CM3
Click here for details Note) Kinetic energy absorbable by the cushion mechanism is identical to double acting, single rod.
CG1
-XAl Change of rod end shape Standard Strokes CG3
-XB6 Heat resistant cylinder (−10 to 150°C)
[mm]
-XC3 Special port location*1 *2
Bore Standard stroke Max.
[mm]
manufacturable
JMB
-XC4 With heavy duty scraper
size Stroke range q Stroke range w stroke
-XC5 Heat resistant cylinder (−10 to 110°C)
Made of stainless steel*2
32 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500 MB
-XC6 Up to 1000
40 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500
-XC7 Tie-rod, cushion valve, tie-rod nut, etc. made of stainless steel
50 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600 MB1
-XC14 Change of trunnion bracket mounting position Up to 1200 Up to
-XC22 63 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600
Fluororubber seal
80 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800
1800
CA2
-XC30 Rod trunnion
-XC35 100 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800 Up to 1500
With coil scraper
125
CS1
-XC68 Made of stainless steel (with hard chrome plated piston rod)*3 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800, 900, 1000
-XC88 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: Stainless steel 304) Note 1) Manufacture of intermediate strokes is possible. (Spacers are not used.)
Note 2) Applicable strokes should be confirmed according to the usage. For details, refer to “Air Cylinders Model CS2
-XC89 Spatter resistant coil scraper, Lube-retainer, Grease for welding (Piston rod: S45C)
Selection” on front matter pages. In addition, the products that exceed the stroke range q might not be able
-XC91 Spatter resistant coil scraper, Grease for welding (Piston rod: S45C) to fulfill the specifications due to the deflection etc.
*1 The cover shape is the same as the current product. Note 3) Please consult with SMC for manufacturability and the part numbers when exceeding the stroke range w.
*2 ø125 only Note 4) The stroke range with rod boot is up to 1000 mm. Please consult with SMC when exceeding 1000 mm
*3 Except ø125 strokes.
For special port location (-XC3), the mounting

bracket and port location can be determined using
Accessories
the standard product corresponding to the operating
conditions. Also, this is only applicable to -XC3BB,
-XC3CC and -XC3DD with trunnion bracket. Center
Mounting Basic Axial foot Rod flange
trunnion
For parts made of stainless steel (-XC6), use the Standard Rod end nut    
same specification stainless steel with the surface Single knuckle joint    
treatment (with hard chrome plated piston rod)
(-XC68).
Option Double knuckle joint (with pin)    
Rod boot    
Refer to pages 425 to 432 for cylinders * Refer to page 401 for dimensions and part numbers. (Refer to page 406 for rod boot.)
with auto switches.
• Auto switch proper mounting position Rod Boot Material
(detection at stroke end) and its
mounting height
• Minimum stroke for auto switch mounting Symbol Material Max. ambient temp.
• Auto switch mounting brackets/Part no. J Nylon tarpaulin 70°C
• Operating range
K Heat resistant tarpaulin 110°C*
* Max. ambient temperature for rod boot itself.
Water Resistant Air Cylinder
Water resistant air cylinders are also avail- Mounting Brackets/Part No.
able in the MB series, which are suitable for D-
use on machine tools in an atmosphere with
coolant and applicable to food machinery Bore size [mm] 32 40 50 63 80 100 125
and automobile washing equipment in an Axial foot MB-L03 MB-L04 MB-L05 MB-L06 MB-L08 MB-L10 MB-L12 -X
environment with water splashes. Please re- Rod flange MB-F03 MB-F04 MB-F05 MB-F06 MB-F08 MB-F10 MB-F12
fer to page 1125 for more information.
Technical
* Order two foots per cylinder. Data
403 B
MBW Series
Theoretical Force
OUT
(Unit: N) IN
Bore size Rod diameter Operating Piston area Operating pressure [MPa]
[mm] [mm] direction [mm2] 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
32 12 IN, OUT 691 138 207 276 346 415 484 553 622 691
40 16 IN, OUT 1056 211 317 422 528 634 739 845 950 1056
50 20 IN, OUT 1649 330 495 660 825 989 1154 1319 1484 1649
63 20 IN, OUT 2803 561 841 1121 1402 1682 1962 2242 2523 2803
80 25 IN, OUT 4536 907 1361 1814 2268 2722 3175 3629 4082 4536
100 30 IN, OUT 7147 1429 2144 2859 3574 4288 5003 5718 6432 7147
125 32 IN, OUT 11468 2294 3440 4588 5734 6881 8028 9174 10321 11468
Weights/Aluminum Tube
[kg]
Bore size [mm] 32 40 50 63 80 100 125
Basic 0.56 0.78 1.37 1.64 3.05 4.23 6.48
Axial foot 0.68 0.92 1.59 1.92 3.55 4.89 8.56
Basic weight
Rod flange 0.85 1.15 1.82 2.43 4.50 7.54 10.64
Center trunnion 0.85 1.14 1.85 2.44 4.60 7.90 9.46
Additional weight per 50 mm of stroke All mounting brackets 0.15 0.24 0.37 0.38 0.61 0.82 1.02
Single knuckle joint 0.15 0.23 0.26 0.26 0.60 0.83 1.08
Accessories
Double knuckle joint (with pin) 0.22 0.37 0.43 0.43 0.87 1.27 1.58
Calculation
Example) MBWB32-100Z (Basic, ø32, 100 stroke)
• Basic weight ··························· 0.56 (Basic, ø32)
• Additional weight ···················· 0.15/50 stroke
• Cylinder stroke ······················· 100 stroke
0.56 + 0.15 x 100/50 = 0.86 kg
404
Construction
u i !4 !6 !1 y q !0 !3 o w e t !2 !7 r !5
CJ1
CJP
CJ2
JCM
CM2
ø32
CM3
CG1
CG3
JMB
MB
MBW125 MB1
CA2
Component Parts
No. Description Material Q’ty Note No. Description Material Q’ty Note CS1
1 Rod cover Aluminum die-cast 2 Trivalent chromated 10 Tie-rod nut Carbon steel 8 Trivalent zinc chromated
2 Cylinder tube Aluminum alloy 1 Hard anodized 11 Rod seal NBR 2 CS2
3 Piston rod Carbon steel 1 Hard chrome plating 12 Piston seal NBR 1
4 Piston Aluminum alloy 1 13 Cushion seal Urethane 2
5 Cushion ring Aluminum alloy 2 Anodized 14 Cushion valve seal NBR 2
6 Bushing Bearing alloy 2 15 Cylinder tube gasket NBR 2
7 Cushion valve Steel wire 2 Trivalent zinc chromated 16 Rod end nut Rolled steel 2 Trivalent zinc chromated
8 Retaining ring Steel for spring 2 ø40 to ø125 17 Magnet — (1)
9 Tie-rod Carbon steel 4 Trivalent zinc chromated
Replacement Parts/Seal Kit

Bore size
Kit no. Contents
[mm]
32 MBW32Z−PS
40 CA2W40Z−PS
50 CA2W50Z−PS
Set of the nos.
63 CA2W63Z−PS
!1, !2, !3, !5
80 CA2W80Z−PS
100 CA2W100Z−PS
125 MBW125−PS
∗ Seal kits consist of items !1, !2, !3, !5, and can be ordered
by using the seal kit number corresponding to each bore size.
∗ Trunnion type should not be disassembled. (Refer to page 434.)
∗ The seal kit includes a grease pack (10 g for ø32 to ø50, 20 g
for ø63 and ø80, 30 g for ø100 and ø125).
Grease pack part number: GR-S-010 (10 g), GR-S-020 (20 g) D-
-X
Technical
Data
405
MBW Series
Standard
Basic: (B) V W
Port Cushion valve
G 2 x Rc P G
Width across flats KA Width across flats KA øE
øD
øD
øE
øE
C
B
MM K MM
Width across H1 MB H1 Width across
flats B1 AL MA AL flats B1 C
2x4xJ
A F N N F K A B
H S + Stroke H + Stroke
ZZ + 2 x Stroke
ød
øe
10.2 10.2
l f
h
With rod boot G 2 x Rc P
Width across flats KA G Width across flats KA
Rubber Bumper
Bore size
[mm]
S ZZ
øD
øD
ød
ød
øe
øe
32 90 184
40 90 192
MM 50 102 218
H1 H1 MM
Width across
63 102 218
AL 10.2 10.2 10.2 10.2 AL Width across
flats B1 80 124 268
A K l f N N f l + Stroke K A flats B1
100 124 268
h S + Stroke h + Stroke
125 132 326
ZZ + 2 x Stroke
[mm]
Bore size
[mm] A AL B B1 C D E F G H H1 J K KA MA MB MM N P S V W ZZ
32 22 19.5 46 17 32.5 12 30 13 13 47 6 M6 x 1 6 10 16 4 M10 x 1.25 27 1/8 84 4 6.5 178
40 30 27 52 22 38 16 35 13 14 51 8 M6 x 1 6 14 16 4 M14 x 1.5 27 1/4 84 4 9 186
50 35 32 65 27 46.5 20 40 14 15.5 58 11 M8 x 1.25 7 18 16 5 M18 x 1.5 31.5 1/4 94 5 10.5 210
63 35 32 75 27 56.5 20 45 14 16.5 58 11 M8 x 1.25 7 18 16 5 M18 x 1.5 31.5 3/8 94 9 12 210
80 40 37 95 32 72 25 45 20 19 72 13 M10 x 1.5 10 22 16 5 M22 x 1.5 38 3/8 114 11.5 14 258
100 40 37 114 41 89 30 55 20 19 72 16 M10 x 1.5 10 26 16 5 M26 x 1.5 38 1/2 114 17 15 258
125 54 50 136 41 110 32 60 27 19 97 16 M12 x 1.75 13 27 20 6 M27 x 2.0 38 1/2 120 17 15 314
With Rod Boot [mm]

l h
Bore size
[mm]
d e f 1 to 51 to 101 to 151 to 201 to 301 to 401 to 501 to 601 to 701 to 801 to 901 to 1 to 51 to 101 to 151 to 201 to 301 to 401 to 501 to 601 to 701 to 801 to 901 to
50 100 150 200 300 400 500 600 700 800 900 1000 50 100 150 200 300 400 500 600 700 800 900 1000
32 54 36 23 12.5 25 37.5 50 75 100 125 — — — — — 73 86 98 111 136 161 186 — — — — —
40 56 41 23 12.5 25 37.5 50 75 100 125 — — — — — 81 94 106 119 144 169 194 — — — — —
50 64 51 25 12.5 25 37.5 50 75 100 125 150 — — — — 89 102 114 127 152 177 202 227 — — — —
63 64 51 25 12.5 25 37.5 50 75 100 125 150 — — — — 89 102 114 127 152 177 202 227 — — — —
80 68 56 29 12.5 25 37.5 50 75 100 125 150 175 200 — — 101 114 126 139 164 189 214 239 264 289 — —
100 76 61 29 12.5 25 37.5 50 75 100 125 150 175 200 — — 101 114 126 139 164 189 214 239 264 289 — —
125 82 75 27 10 20 30 40 60 80 100 120 140 160 180 200 120 130 140 150 170 190 210 230 250 270 290 310
Note) ZZ indicates dimensions for double side rod boot. [mm]
ZZ Note)
Bore size
[mm] 1 to 51 to 101 to 151 to 201 to 301 to 401 to 501 to 601 to 701 to 801 to 901 to
50 100 150 200 300 400 500 600 700 800 900 1000
32 230 256 280 306 356 406 456 — — — — —
40 246 272 296 322 372 422 472 — — — — —
50 272 298 322 348 398 448 498 548 — — — —
63 272 298 322 348 398 448 498 548 — — — — ∗ Model without air cushion is designed to include rubber bumpers.
80 316 342 366 392 442 492 542 592 642 692 — — Since the bumpers are attached to the both sides of the piston, the
100 316 342 366 392 442 492 542 592 642 692 — — overall length is longer than the cylinder with air cushion as follows: ø32,
125 360 380 400 420 460 500 540 580 620 660 700 740 ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø100: +10 mm, ø125: +12 mm
A 406
Standard/With Mounting Bracket ∗ Refer to Basic (B) for other dimensions and with rod boot.
Axial foot: (L)

Port Cushion valve
CJ1
LY
CJP
LH
CJ2
LT
X X 4 x øLD LX
Y LS + Stroke Y LZ
JCM
[mm]
CM2
Bore size
[mm] X Y LD LH LS∗ LT LX LY LZ
32 22 9 7 30 128 3.2 32 53 50 CM3
40 24 11 9 33 132 3.2 38 59 55
50 27 11 9 40 148 3.2 46 72.5 70 CG1
63 27 14 12 45 148 3.6 56 82.5 80
80 30 14 12 55 174 4.5 72 102.5 100 CG3
100 32 16 14 65 178 4.5 89 122 120
125 45 20 14 81 210 8 90 149 136
JMB
Rod flange: (F)
FT Port Cushion valve MB
4 x øFD
MB1
CA2
øFd
FB
FY
CS1
FX
FZ CS2
[mm]
Bore size
[mm] FB FD FT FX FY FZ Fd
32 50 7 10 64 32 79 24.5
40 55 9 10 72 36 90 29.5
50 70 9 12 90 45 110 35.5
63 80 9 12 100 50 120 38.5
80 100 12 16 126 63 153 41
100 120 14 16 150 75 178 46
125 138 14 20 180 102 216 57
Center trunnion: (T)
Z + 1/2 stroke Port Cushion valve
øTDe8
TY
TT TX
TZ
[mm]
Bore size
[mm] TDe8 TT TX TY TZ Z∗∗
Since the bumpers are attached to the both sides of the piston, the overall length is 32 12 17 50 49 74 89
longer than the cylinder with air cushion as follows: ø32, ø40: +6 mm, ø50, ø63: +8 mm, 40 16 22 63 58 95 93 D-
ø80, ø100: +10 mm, ø125: +12 mm 50 16 22 75 71 107 105
∗∗ Model without air cushion is designed to include rubber bumpers. 63
Since the bumpers are attached to the both sides of the piston, the “Z” dimension is 80
20
20
28
34
90
110
87
110
130
150
105
129
-X
longer than the cylinder with air cushion as follows: ø32, ø40: +3 mm, ø50, ø63: +4 mm, 100 25 40 132 136 182 129 Technical
ø80, ø100: +5 mm, ø125: +6 mm (For trunnion mounting) 125 25 50 160 160 210 157 Data
407 A
Air Cylinder: Non-rotating Rod Type
Double Acting, Single Rod
MBK Series RoHS
ø32, ø40, ø50, ø63, ø80, ø100

How to Order
MBK B 32 50 Z
With auto switch MDBK B 32 50 Z M9BW
With auto switch Accessories 1 Number of
(Built-in magnet) Nil No bracket Auto switch auto switches
N Pivot bracket
Nil Without auto switch Nil 2 pcs.
Mounting type
* Only for D and T mounting types. * For applicable auto switches, S 1 pc.
B Basic/Without bracket * Pivot bracket is shipped together
L Axial foot Bore size with the product.
refer to the table below. 3 3 pcs.
F Rod flange 32 32 mm * For details, refer to page 400. n “n” pcs.
G Head flange 40 40 mm Suffix (Cushion)
C Single clevis 50 50 mm Made to Order
Nil Air cushion For details, refer to page 409.
D Double clevis 63 63 mm
N* Rubber bumper
T Center trunnion 80 80 mm Accessories 2
* Since the bumpers are attached to the both sides of the
* Mounting brackets other than 100 100 mm piston for rubber bumper type, the overall length is Nil No bracket
trunnion type are shipped longer than the cylinder with air cushion as follows: ø32, V Single knuckle joint
together. ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø100: +10 mm.
W Double knuckle joint
Port thread type Suffix (Rod boot)
* A knuckle joint pin is not provided with the single knuckle
joint.
Nil Rc
Nil None * Rod end bracket is shipped together with the product.
Cylinder stroke [mm]
TN NPT
Refer to “Standard Strokes” J Nylon tarpaulin * The screw-in amount of the piston rod end cannot be
TF G on page 409. K Heat resistant tarpaulin
adjusted when a clevis bracket, trunnion bracket and
knuckle joint are used together.
Indicator light

Type Special function Tie-rod Band 0.5 1 3 5 connector
entry (Output) DC AC load
3-wire (NPN) M9N — V V V v v
Grommet 3-wire (PNP) 24 V — M9P — V V V v v
conduit 2-wire 12 V — K39 — — — — —

3-wire (NPN) M9NW — V V V v v
(2-color indicator)
3-wire (PNP) M9PW — V V V v v Relay,
Yes
2-wire 12V M9BW — V V V v v — PLC
3-wire (NPN) 24 V — M9NA*1 — v v V v v
(2-color indicator)
Grommet 3-wire (PNP) M9PA*1 — v v V v v
2-wire 12 V M9BA*1 — v v V v v —
Diagnostic output (2-color indicator) 4-wire (NPN) 5 V, 12 V F59F — V — V v v IC circuit
— —
3-wire (Equiv. to NPN) — 5V — A96 — V — V — — IC circuit —
Yes
100 V A93 — V V V V — —
Reed auto switch
Grommet No 100 V or less A90 — V — V — — IC circuit

Relay,
Yes 100 V, 200 V A54 — V — V V —
— PLC
No 12 V 200 V or less A64 — V — V — —
2-wire 24 V
Terminal — — A33 — — — — —
—
Yes 100 V, 200 V
Diagnostic indication (2-color indicator) Grommet — — A59W — V — V — — PLC
A water resistant type cylinder is recommended for use in an environment which requires water resistance.
* Lead wire length symbols: 0.5 m ········ Nil (Example) M9NW 3 m ········· L (Example) M9NWL
1 m ········· M (Example) M9NWM 5 m ········· Z (Example) M9NWZ
before shipment.)
A 408
Double Acting, Single Rod MBK Series
Specifications
Bore size [mm] 32 40 50 63 80 100

Fluid Air
Maximum operating pressure 1.0 MPa
Minimum operating pressure 0.05 MPa CJP
Ambient and fluid temperature
Without auto switch: –10 to 70°C
With auto switch: –10 to 60°C
(No freezing) CJ2
Lubricant Non-lube JCM
Piston speed 50 to 1000 mm/s
Stroke length tolerance Up to 250: +1.0 +1.4 +1.8
0 , 251 to 1000: 0 , 1001 to 1500: 0 CM2
Cushion Note) Air cushion or Rubber bumper
Symbol Port size (Rc, NPT, G) 1/8 1/4 3/8 1/2 CM3
Double acting, Air cushion
Basic, Axial foot, Rod flange, Head flange,
Mounting
±0.5° ±0.5° ±0.3°
Non-rotating accuracy
CG3
Allowable rotating torque N·m or less 0.25 0.45 0.64 0.79 0.93
Note) Kinetic energy absorbable by the cushion mechanism is identical to double acting single rod. JMB
MB
Standard Strokes
Made to Order
Click here for details [mm] MB1
Bore size Standard stroke CA2
-XA Change of rod end shape
-XC3 Special port location* 32 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500
CS1
Tie-rod, cushion valve, tie-rod nut, etc. 40 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500
-XC7 made of stainless steel 50 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600 CS2
-XC8 Adjustable stroke cylinder/Adjustable extension type 63 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600
-XC9 Adjustable stroke cylinder/Adjustable retraction type 80 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700
-XC10 Dual stroke cylinder/Double rod type 100 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700
-XC14 Change of trunnion bracket mounting position Manufacture of intermediate strokes is possible. (Spacers are not used.)
-XC30 Rod trunnion Accessories

* The cover shape is the same as the current
product.
Axial Rod Head Single Double Center
Mounting Basic
foot flange flange clevis clevis trunnion
Rod end nut V V V V V V V
Standard
For special port location (-XC3), the mounting Clevis pin — — — — — V —
bracket and port location can be determined using Single knuckle joint V V V V V V V
the standard product corresponding to the
operating conditions. Also, this is only applicable Double knuckle joint
to -XC3BB, -XC3CC and -XC3DD with trunnion
Option V V V V V V V
(with pin)
bracket.
Rod boot V V V V V V V
* Refer to page 401 for dimensions and part numbers. (Refer to page 396 for rod boot.)
Refer to pages 425 to 432 for cylinders with Rod Boot Material
auto switches.
• Auto switch proper mounting position (detection Symbol Material Max. ambient temp.
at stroke end) and its mounting height
J Nylon tarpaulin 70°C
• Minimum stroke for auto switch mounting
D-
• Operating range -X
Technical
Data
409 B
MBK Series
Mounting Brackets/Part No.
Bore size
[mm]
32 40 50 63 80 100
Axial foot Note 1) MB-L03 MB-L04 MB-L05 MB-L06 MB-L08 MB-L10

Rod/Head flange MB-F03 MB-F04 MB-F05 MB-F06 MB-F08 MB-F10
Single clevis MB-C03 MB-C04 MB-C05 MB-C06 MB-C08 MB-C10
Double clevis MB-D03 MB-D04 MB-D05 MB-D06 MB-D08 MB-D10
Note 2) Accessories for each mounting bracket are as follows. Axial foot, Rod/Head flange, Single
clevis/Body mounting bolt; Double clevis/Body mounting bolt, Clevis pin, Flat washers and Split
pins. → Refer to page 401 for details.
Theoretical Force
OUT side is identical to double acting single rod. Refer to the table below for IN side.
Bore size [mm] Piston area [mm2]
32 675
40 1082
50 1651
63 2804
80 4568
100 7223
Theoretical force [N] = Pressure [MPa] x Piston area [mm2]
Weights
[kg]
Bore size [mm] 32 40 50 63 80 100
Basic 0.47 0.64 1.11 1.35 2.54 3.52
Axial foot 0.59 0.78 1.33 1.63 3.04 4.19
Rod/Head flange 0.76 1.01 1.56 2.14 3.99 6.84
Basic weight
Single clevis 0.72 0.87 1.45 1.98 3.65 6.70
Double clevis 0.73 0.91 1.54 2.14 3.94 7.22
Center trunnion 0.76 1.00 1.59 2.15 4.09 7.20
Additional weight per 50 mm of stroke All mounting brackets 0.12 0.15 0.24 0.26 0.39 0.50
Single knuckle joint 0.15 0.23 0.26 0.26 0.60 0.83
Accessories
Double knuckle joint (with pin) 0.22 0.37 0.43 0.43 0.87 1.27
Calculation
Example) MBKB32-100Z (Basic, ø32, 100 stroke)
• Basic weight ······················· 0.47 (Basic, ø32)
• Additional weight ················ 0.12/50 stroke
• Cylinder stroke ··················· 100 stroke
0.47 + 0.12 x 100/50 = 0.71 kg
410
Double Acting, Single Rod MBK Series
Construction
!9 !4 i @1 q !2 !6 !1 e r y !5 @0 !3 t !8 w u o !0 !7
CJ1
across flats
Width
CJP
Rod view
CJ2
ø32 (2:1) ø32
JCM
CM2
Component Parts CM3
No. Description Material Q’ty Note No. Description Material Q’ty Note
1 Rod cover 12 Tie-rod nut
2 Head cover
Aluminum die-casted 1 Trivalent chromated
Aluminum die-casted 1 Trivalent chromated 13 Wear ring
Carbon steel
Resin
8 Trivalent zinc chromated
1
CG1
3 Cylinder tube Aluminum alloy 1 Hard anodized 14* Rod seal NBR 1
4 Piston rod Stainless steel 1 15* Piston seal NBR 1 CG3
5 Piston Aluminum alloy 1 16* Cushion seal Urethane 2
6 Cushion ring Rolled steel 2 Zinc chromated 17 Cushion valve seal NBR 2 JMB
7 Piston nut Rolled steel 1 Zinc chromated 18* Cylinder tube gasket NBR 2
8
9
Non-rotating guide
Cushion valve
Bearing alloy
Steel wire
1
19
20
Rod end nut
Magnet
Rolled steel
—
(1)
MB
10 Retaining ring Spring steel 2 ø40 to ø100 21 Hexagon socket head set screw Steel wire 2 Trivalent black zinc chromated
11 Tie-rod Carbon steel 4 Trivalent zinc chromated MB1
Replacement Parts/Seal Kit CA2
Bore size [mm] Kit no. Contents
32 MBK32Z−PS
40 MBK40Z−PS CS1
* Seal kits consist of items !4, !5, !6, !8, and can be ordered by using the
50 MBK50Z−PS Set of the nos.
63 MBK63Z−PS !4, !5, !6, !8
seal kit number corresponding to each bore size.
* Seal kit includes a grease pack (ø32 to 50: 10 g, ø63, 80: 20 g, ø100: 30 g).
CS2
80 MBK80Z−PS Order with the following part number when only the grease pack is needed.
100 MBK100Z−PS Grease pack part number: GR-S-010 (10 g), GR-S-020 (20 g)
* Model without air cushion is designed to include rubber bumpers. The overall length is longer than the cylinder with air cushion
as follows because the bumpers are attached to the both sides of the piston;
ø32, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø100: +10 mm
Without Mounting Bracket

Basic: (B) G 2 x Rc P G Cushion valve W V Port
øE
A
MM
øE
D
C
B
A'
Section A-A'
Width across flats B1 H1 MB
AL MA
A F N 2x4xJ N C
H S + Stroke B
ZZ + Stroke
[mm]
Bore size
[mm]
A AL B B1 C D E F G H H1 J MA MB MM N P S V W ZZ
32 22 19.5 46 17 32.5 12.2 30 13 13 47 6 M6 x 1 16 4 M10 x 1.25 27 1/8 84 4 6.5 135
40 30 27 52 22 38 14.2 35 13 14 51 8 M6 x 1 16 4 M14 x 1.5 27 1/4 84 4 9 139
50 35 32 65 27 46.5 19 40 14 15.5 58 11 M8 x 1.25 16 5 M18 x 1.5 31.5 1/4 94 5 10.5 156 D-
63 35 32 75 27 56.5 19 45 14 16.5 58 11 M8 x 1.25 16 5 M18 x 1.5 31.5 3/8 94 9 12 156
80
100
40
40
37
37
95
114
32
41
72
89
23
27
45
55
20
20
19
19
72
72
13
16
M10 x 1.5
M10 x 1.5
16
16
5
5
M22 x 1.5
M26 x 1.5
38
38
3/8
1/2
114
114
11.5
17
14
15
190
190
-X
Technical
The dimensions for each mounting type and the dimensions with rod boot are the same as those for standard model (double acting, single rod). Data
411
Double Acting, Double Rod
MBKW Series RoHS
ø32, ø40, ø50, ø63, ø80, ø100

How to Order
MBKW L 32 150 Z
With auto switch MDBKW L 32 150 Z M9BW
With auto switch Number of auto switches
(Built-in magnet)
Nil 2 pcs.
Auto switch S 1 pc.
Mounting type
Nil Without auto switch 3 3 pcs.
B Basic/Without bracket n “n” pcs.
* For applicable auto switches,
L Axial foot Bore size refer to the table below.
F Rod flange 32 32 mm Made to Order
T Center trunnion 40 40 mm Port thread For details, refer to page 413.
* Mounting brackets other than 50 50 mm
trunnion type are shipped type
63 63 mm Nil Rc
together.
80 80 mm
Suffix (Cushion)
TN NPT Nil Air cushion
100 100 mm TF G
Suffix (Rod boot) N* Rubber bumper
* Since the bumpers are attached
Nil None
to the both sides of the piston for
Cylinder stroke [mm] J Nylon tarpaulin (one end) rubber bumper type, the overall
Refer to “Standard Strokes” on page 413. JJ Nylon tarpaulin (both ends) length is longer than the cylinder
K Heat resistant tarpaulin (one end) with air cushion as follows: ø32,
ø40: +6 mm, ø50, ø63: +8 mm,
KK Heat resistant tarpaulin (both ends) ø80, ø100: +10 mm.
Indicator light
Electrical Wiring Pre-wired

Type Special function Tie-rod Band 0.5 1 3 5 Applicable load
entry (Output) DC AC connector
conduit 2-wire 12 V — K39 — — — — —

(2-color indicator)
Yes
2-wire 12 V M9BW — V V V v v — PLC
3-wire (NPN) 24 V — M9NA * 1 — v v V v v
Water resistant 5 V, 12 V * IC circuit
(2-color indicator)
Grommet 3-wire (PNP) M9PA 1 — v v V v v
— —
3-wire
— 5V — A96 — V — V — — IC circuit —
Yes (Equiv. to NPN)
100 V A93 — — —
Reed auto switch
V V V V
Grommet
No 100 V or less A90 — V — V — — IC circuit
Relay,
— Yes 100 V, 200 V A54 — V — V V —
PLC
No 12 V 200 V or less A64 — V — V — —
2-wire 24 V
Terminal — — A33 — — — — —
—
Yes 100 V, 200 V
* Solid state auto switches marked with “v” are produced upon receipt of order.
before shipment.)
A 412
Double Acting, Double Rod MBKW Series
Specifications
Bore size [mm] 32 40 50 63 80 100

Action Double acting, Double rod
Fluid Air
Min. operating pressure 0.05 MPa CJP
(No freezing) CJ2
Lubrication Non-lube
JCM
Operating piston speed 50 to 1000 mm/s
Allowable stroke tolerance Up to 250: +1.0 +1.4
0 , 251 to 800: 0 CM2
Cushion Note) Air cushion or Rubber bumper
Symbol Port size (Rc, NPT, G) 1/8 1/4 3/8 1/2 CM3
Double acting Mounting Basic, Axial foot, Rod flange, Center trunnion
Non-rotating accuracy ±0.5° ±0.5° ±0.3°
CG1
Allowable rotating torque N·m or less 0.25 0.45 0.64 0.79 0.93
CG3
Note) Kinetic energy absorbable by cushion mechanism is identical to double acting single rod.
JMB
Standard Strokes
Made to Order [mm]
MB
Bore size Standard stroke MB1
Special port location*
-XC3 32 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500 CA2
Tie-rod, cushion valve, tie-rod nut, etc. 40 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500
-XC7 made of stainless steel
50 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600 CS1
-XC30 Rod trunnion
63 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600
* The cover shape is the same as the current
80 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700 CS2
product.
100 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700
For special port location (-XC3), the mounting Manufacture of intermediate strokes is possible. (Spacers are not used.)
bracket and port location can be determined
using the standard product corresponding to the
operating conditions. Also, this is only applicable Accessories
to -XC3BB, -XC3CC and -XC3DD with trunnion
bracket.
Center
Mounting Basic Axial foot Rod flange
trunnion
Standard Rod end nut V V V V
Single knuckle joint V V V V
Option Double knuckle joint (with pin) V V V V
Rod boot V V V V
* Refer to page 401 for dimensions and part numbers. (Except rod boot)
Rod Boot Material
Symbol Material Max. ambient temp.

J Nylon tarpaulin 70°C
Refer to pages 425 to 432 for cylinders with
auto switches.
• Auto switch proper mounting position
(detection at stroke end) and its mounting Mounting Brackets/Part No.
height D-
• Minimum stroke for auto switch mounting Bore size [mm] 32 40 50 63 80 100
• Auto switch mounting brackets/Part no. Axial foot MB-L03 MB-L04 MB-L05 MB-L06 MB-L08 MB-L10 -X
• Operating range Rod flange MB-F03 MB-F04 MB-F05 MB-F06 MB-F08 MB-F10 Technical
Note) Order two foots per cylinder. Data
413 B
MBKW Series
Theoretical Force
OUT
(Unit: N) IN
Bore size Rod dia. [mm] Operating Piston area Operating pressure [MPa]
[mm] Width across flats [mm] direction [mm2] 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
12 OUT 691 138 207 276 346 415 484 553 622 691
32
12.2 IN 675 135 203 270 338 405 473 540 608 675
16 OUT 1056 211 317 422 528 634 739 845 950 1056
40
14.2 IN 1082 216 325 433 541 649 757 866 974 1082
20 OUT 1649 330 495 660 825 989 1154 1319 1484 1649
50
19 IN 1651 330 495 660 826 991 1156 1321 1486 1651
20 OUT 2803 561 841 1121 1402 1682 1962 2242 2523 2803
63
19 IN 2804 561 841 1122 1402 1682 1963 2243 2524 2804
25 OUT 4536 907 1361 1814 2268 2722 3175 3629 4082 4536
80
23 IN 4568 914 1370 1827 2284 2741 3198 3654 4111 4568
30 OUT 7147 1429 2144 2859 3574 4288 5003 5718 6432 7147
100
27 IN 7223 1445 2167 2889 3612 4334 5056 5778 6501 7223
Weights/Aluminum Tube
[kg]
Bore size [mm] 32 40 50 63 80 100
Basic 0.56 0.77 1.34 1.60 2.99 4.10
Axial foot 0.68 0.91 1.56 1.88 3.49 4.76
Basic weight
Rod flange 0.85 1.14 1.79 2.39 4.44 7.41
Center trunnion 0.85 1.13 1.82 2.40 4.54 7.77 Calculation
Example) MBKWB32-100Z (Basic, ø32, 100 st)
Additional weight per 50 mm of stroke All mounting brackets 0.16 0.23 0.37 0.38 0.60 0.79
• Basic weight ···0.56 (Basic, ø32)
Single knuckle joint 0.15 0.23 0.26 0.26 0.6 0.83 • Additional weight ···0.16/50 stroke
Accessories
Double knuckle joint (with pin) 0.22 0.37 0.43 0.43 0.87 1.27 0.56 + 0.16 x 100/50 = 0.88 kg
Construction
!7 12-1 7-1 !9 1-1 !1 !4 !0 w e y !3 !8 t !6 1-2 7-2 12-2 r i o !5
across flats
Width
Rod view
ø32 (2:1)
Component Parts
No. Description Material Q’ty Note No. Description Material Q’ty Note
1-1 Rod cover Aluminum die-casted 1 Non-rotating rod 17 Rod end nut Rolled steel 2 Trivalent zinc chromated
1-2 Rod cover Aluminum die-casted 1 Standard 18 Magnet — (1)
2 Cylinder tube Aluminum alloy 1 Hard anodized 19 Hexagon socket head set screw Steel wire 2 Trivalent black zinc chromated
3 Piston rod A Stainless steel 1 Non-rotating rod
4 Piston rod B Carbon steel 1 Standard Replacement Parts/Seal Kit
5 Piston Aluminum alloy 1
6 Cushion ring Rolled steel 2 Zinc chromated Bore size
Kit no. Contents
[mm]
7-1 Non-rotating guide Bearing alloy 1 Non-rotating rod
7-2 Bushing Bearing alloy 1 Standard 32 MBKW32Z−PS
8 Cushion valve Steel wire 2 Trivalent zinc chromated 40 MBKW40Z−PS
9 Retaining ring Spring steel 2 ø40 to ø100 50 MBKW50Z−PS Set of the nos.
10 Tie-rod Carbon steel 4 Trivalent zinc chromated 63 MBKW63Z−PS !2, !3, !4, !6
11 Tie-rod nut Carbon steel 8 Trivalent zinc chromated 80 MBKW80Z−PS
12-1*Rod seal NBR 1 Non-rotating rod 100 MBKW100Z−PS
12-2*Rod seal NBR 1 Standard * Seal kits consist of items !2, !3, !4, !6, and can be ordered by using
the seal kit number corresponding to each bore size.
13* Piston seal NBR 1 * Trunnion type should not be disassembled. (Refer to page 434.)
14* Cushion seal Urethane 2 * Seal kit includes a grease pack (ø32 to 50: 10 g, ø63, 80: 20 g, ø100: 30 g).
15 Cushion valve seal NBR 2 Order with the following part number when only the grease pack is needed.
16* Cylinder tube gasket NBR 2 Grease pack part number: GR-S-010 (10 g), GR-S-020 (20 g)
414
Double Acting, Double Rod MBKW Series
Standard
Basic: (B) Cushion valve
G 2 x Rc P G Port V W
Width across flats KB

Q
øE CJ1
CJP
MM
MM
KA
øD
øE
øE
C
B
Section Q-Q CJ2
Q
Width across flats B1 H1 MB H1
Width across
flats B1 JCM
AL MA AL
A F N 2x4xJ N F K A C CM2
H S + Stroke H + Stroke B
ZZ + 2 x Stroke CM3
CG1
Positional relationship between port and cushion valve CG3
Port JMB
MB
MB1
Cushion valve CA2
CS1
CS2
[mm]
Bore size
[mm]
A AL B B1 C D E F G H H1 J K KA KB
32 22 19.5 46 17 32.5 12 30 13 13 47 6 M6 x 1 6 12.2 10
40 30 27 52 22 38 16 35 13 14 51 8 M6 x 1 6 14.2 14
50 35 32 65 27 46.5 20 40 14 15.5 58 11 M8 x 1.25 7 19 18
63 35 32 75 27 56.5 20 45 14 16.5 58 11 M8 x 1.25 7 19 18
80 40 37 95 32 72 25 45 20 19 72 13 M10 x 1.5 10 23 22
100 40 37 114 41 89 30 55 20 19 72 16 M10 x 1.5 10 27 26
[mm]
Bore size
[mm]
MA MB MM N P S* V W ZZ*
32 16 4 M10 x 1.25 27 1/8 84 4 6.5 178
40 16 4 M14 x 1.5 27 1/4 84 4 9 186
50 16 5 M18 x 1.5 31.5 1/4 94 5 10.5 210
63 16 5 M18 x 1.5 31.5 3/8 94 9 12 210
80 16 5 M22 x 1.5 38 3/8 114 11.5 14 258
100 16 5 M26 x 1.5 38 1/2 114 17 15 258
* Model without air cushion is designed to include rubber bumpers. The overall length is longer than the cylinder with air cushion as follows
because the bumpers are attached to the both sides of the piston; ø32, ø40: +6 mm, ø50, ø63: +8 mm, ø80, ø100: +10 mm
The dimensions for each mounting type are the same as those for standard model (double acting, double rod). Refer to pages 406 and 407. D-
-X
Technical
Data
415
Air Cylinder: With End Lock
MBB Series RoHS
ø32, ø40, ø50, ø63, ø80, ø100

How to Order
MBB L 32 50 H N
With auto switch MDBB L 32 50 H N M9BW
With auto switch
(Built-in magnet)
Mounting type Made to Order
Bore size Manual release For details, refer to page 417.
B Basic/Without bracket
32 32 mm N Non-locking
L Axial foot
40 40 mm L Locking Number of
F Rod flange
G Head flange 50 50 mm auto switches
C Single clevis 63 63 mm Locking position Nil 2 pcs.
D Double clevis 80 80 mm H Locking at head end S 1 pc.
T Center trunnion 100 100 mm R Locking at rod end 3 3 pcs.
W Locking at both ends n “n” pcs.
Port thread type
Built-in Magnet Cylinder Model Auto switch
Nil Rc Suffix (Rod boot)
If a built-in magnet cylinder without an TN NPT Nil Without auto switch
Nil None
auto switch is required, there is no need TF G * For applicable auto switches, refer to
to enter the symbol for the auto switch.
J Nylon tarpaulin
the table below.
(Example) MDBBB40-100 Cylinder stroke [mm] K Heat resistant tarpaulin
Refer to “Standard Strokes” on page 417.
Indicator light

Type Special function Tie-rod Band 0.5 1 3 5 connector
entry (Output) DC AC load
conduit 2-wire 12 V — K39 — — — — —

(2-color indicator)
Yes
2-wire 12V M9BW — V V V v v — PLC
3-wire (NPN) 24 V — M9NA*1 — v v V v v
(2-color indicator)
Grommet 3-wire (PNP) M9PA*1 — v v V v v
— —
3-wire
— 5V — A96 — V — V — — IC circuit —
Yes (Equiv. to NPN)
100 V A93 — — —
Reed auto switch
V V V V
Grommet
No 100 V or less A90 — V — V — — IC circuit
Relay,
— Yes 100 V, 200 V A54 — V — V V —
PLC
No 12 V 200 V or less A64 — V — V — —
2-wire 24 V
Terminal — — A33 — — — — —
—
Yes 100 V, 200 V
* The D-A9l/M9l/P3DWAlA auto switches are shipped together, (but not assembled). (However, auto switch mounting brackets are assembled for the D-A9l/M9l
before shipment.)
A 416
Air Cylinder: With End Lock MBB Series
Specifications
Bore size [mm] 32 40 50 63 80 100

Fluid Air
Min. operating pressure 0.15 MPa* CJP
(No freezing) CJ2
Symbol
Lubrication Non-lube
JCM
Operating piston speed 50 to 1000 mm/s
Air cushion
Allowable stroke tolerance Up to 250: +1.0
0 , 251 to 1000: +1.4
0 , 1001 to 1500: +1.8
0 CM2
Cushion Air cushion
Port size (Rc, NPT, G) 1/8 1/4 3/8 1/2 CM3
Basic, Axial foot, Rod flange, Head flange,
Mounting
* 0.05 MPa except locking parts
CG3
JMB
Locking Specifications
Made to Order MB
Locking position Head end, Rod end, Both ends
Symbol Specifications MB1
ø32 ø40 ø50 ø63 ø80 ø100
-XAl Change of rod end shape Holding force (Max.) N
Tie-rod, cushion valve, tie-rod nut, etc.
550 860 1340 2140 3450 5390 CA2
-XC7 made of stainless steel Back lash 1.5 mm or less
-XC10 Dual stroke cylinder/Double rod type Manual release Non-locking type, Locking type CS1
-XC14 Change of trunnion bracket mounting position
CS2
-XC29 Double knuckle joint with spring pin

Standard Strokes
-XC30 Rod trunnion [mm]
* All Made-to-Order products have the same Bore size Standard stroke
cover shapes as the current products. 32 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500
40 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500
50 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600
Refer to pages 425 to 432 for cylinders with
auto switches. 63 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600
• Auto switch proper mounting position 80 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800
(detection at stroke end) and its mounting
100 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600, 700, 800
height
• Minimum stroke for auto switch mounting Intermediate strokes are available. (No spacer is used.)
• Operating range
Accessories
Axial Rod Head Single Double Center

Mounting Basic
foot flange flange clevis clevis trunnion
Rod end nut V V V V V V V
Clevis pin — — — — — V —
Standard
Locking release bolt
V V V V V V V
(N type only)
Single knuckle joint V V V V V V V
D-
Option V V V V V V V
(with pin)
-X
Rod boot V V V V V V V
Technical
* Refer to page 401 for dimensions and part numbers. (Except locking release bolt and rod boot)
Data
417 A
MBB Series
Weights/Aluminum Tube Additional Weight of Locking Part

[kg] [kg]
Bore size [mm] 32 40 50 63 80 100 Bore size [mm] 32 40 50 63 80 100
Basic 0.50 0.69 1.19 1.47 2.73 3.7 Locking at head end (H) 0.08 0.13 0.21 0.30 0.75 1.1
Manual release Locking at rod end (R) 0.08
Axial foot 0.68 0.93 1.56 1.93 3.61 4.8 non-locking (N)
0.13 0.20 0.29 0.71 1.03
Rod/Head flange 0.79 1.06 1.64 2.26 4.18 7.01 Locking at both ends (W) 0.16 0.26 0.41 0.59 1.46 2.13
Basic weight
Single clevis 0.75 0.92 1.53 2.1 3.84 6.87 Locking at head end (H) 0.09 0.15 0.23 0.32 0.78 1.13
Manual release
Double clevis 0.76 0.96 1.62 2.26 4.13 7.39 locking (L) Locking at rod end (R) 0.09 0.15 0.22 0.31 0.74 1.06
Center trunnion 0.79 1.05 1.67 2.27 4.28 7.37 Locking at both ends (W) 0.18 0.30 0.45 0.63 1.52 2.19
Additional weight All mounting Calculation

0.11 0.16 0.26 0.27 0.42 0.56
per 50 mm of stroke brackets Example) MBBL32-100-HN
• Basic weight ······················ 0.68
Single knuckle • Additional weight ··············· 0.11/50 stroke
0.15 0.23 0.26 0.26 0.60 0.83
joint • Cylinder stroke ·················· 100 stroke
Accessories • Locking weight ·················· 0.08 (Locking at head end, manual release
Double knuckle non-locking type)
0.22 0.37 0.43 0.43 0.87 1.27
joint (with pin)
0.68 + 0.11 x 100/50 + 0.08 = 0.98 kg
Mounting Brackets/Part No.
Bore size [mm] 32 40 50 63 80 100

Axial foot Note 1) MB-L03 MB-L04 MB-L05 MB-L06 MB-L08 MB-L10
Rod/Head flange MB-F03 MB-F04 MB-F05 MB-F06 MB-F08 MB-F10
Single clevis MB-C03 MB-C04 MB-C05 MB-C06 MB-C08 MB-C10
Double clevis MB-D03 MB-D04 MB-D05 MB-D06 MB-D08 MB-D10
Note 2) Accessories for each mounting bracket are as follows.
Axial foot, Rod/Head flange, Single clevis/Body mounting bolt; Double clevis/
Body mounting bolt, Clevis pins, Flat washer and Split pins. → Refer to page 401
for details.
418
Construction
Locking at head end
Manual release non-locking type: N
!3 r #0 q u @9 #2 e y!6 #1 @8 t !2 w #3 !5 !7 14A @1 @6 CJ1

!8
!9 CJP
@0
CJ2
@7
i JCM
o ø80, ø100
CM2
CM3
!1 !0 CG1
@2 @3 N@4 @5 14B CG3

Locking at rod end
JMB
MB
MB1
CA2
Manual release locking type: L
CS1
Component Parts Component Parts

CS2
No. Description Material Note No. Description Material Note
1 Rod cover Aluminum alloy Metallic painted 17 Lock spring Steel wire
2 Head cover Aluminum alloy Metallic painted 18 Bumper Urethane
3 Cylinder tube Aluminum alloy Hard anodized 19 Lock piston Carbon steel Hardened, Hard chrome plating
4 Piston rod Carbon steel Hard chrome plating 20 Lock bushing Copper allow
5 Piston Aluminum alloy Chromated 21 Bolt with hex. hole Alloyed steel Black zinc chromated
6 Cushion ring Aluminum alloy Anodized 22 M/O knob Zinc alloy Painted black
7 Bushing Bearing alloy 23 M/O bolt Alloyed steel Black zinc chromated, Painted red
8 Cushion valve Steel wire Trivalent zinc chromated 24 M/O spring Steel wire Zinc chromated
9 Retaining ring Steel for spring ø40 to ø100 25 Stopper ring Carbon steel Zinc chromated
10 Tie-rod Carbon steel Trivalent zinc chromated 26 Seal retainer Rolled steel ø80, ø100 only
11 Tie-rod nut Carbon steel Trivalent zinc chromated 27 Cushion valve seal NBR
12 Wear ring Resin 28 Piston gasket NBR
13 Rod end nut Carbon steel Trivalent zinc chromated 29 * Cushion seal Urethane
14A Cover A Aluminum alloy Painted black 30 * Rod seal NBR
14B Cover B Carbon steel Tufftride 31 * Piston seal NBR
15 Rubber cover Synthetic rubber 32 * Cylinder tube gasket NBR
16 Piston holder Urethane 33 * Lock piston seal NBR
Replacement Parts/Seal Kit (Locking at head or rod end) Replacement Parts/Seal Kit (Locking at both ends)
Bore size [mm] Kit no. Contents Bore size [mm] Kit no. Contents
32 MBB32-PS 32 MBB32-PS-W
50 MBB50-PS Set of the nos. 50 MBB50-PS-W Set of the nos.
63 MBB63-PS @9, #0, #1, #2, #3 63 MBB63-PS-W @9, #0, #1, #2, #3
100 MBB100-PS 100 MBB100-PS-W
* Seal kits consist of items @9 to #3, and can be ordered by using the seal kit
number corresponding to each bore size. D-
* Trunnion type should not be disassembled. (Refer to page 434.)
* Seal kit includes a grease pack (ø32 to 50: 10 g, ø63, 80: 20 g, ø100: 30 g). -X
Grease pack part number: GR-S-010 (10 g), GR-S-020 (20 g) Technical
Data
419
MBB Series
Basic: (B)
Locking at head end: MBBB Bore size Port thread type Stroke Hl
Manual release non-locking type: N Manual release locking type: L
W V Port
G GB HN
MM 2xP Cushion valve HR
øMO
øRF
øD
øE
WL
øE
B
C
H1
MB LL
Width across flats KA
MA 2x4xJ DL C
AL
B
A K F N NB
H S + Stroke
ZZ + Stroke
Locking at rod end: MBBB Bore size Port thread type Stroke Rl
Locking at both ends: MBBB Bore size Port thread type Stroke Wl
-Hl/-Rl [mm]
Bore size
[mm] AL KA A B C D DL E F G GB H1 H HR HN J K LL MA MB
32 19.5 10 22 46 32.5 12 9 30 13 13 21 6 47 33.5 45 M6 x 1 6 15 16 4
40 27 14 30 52 38 16 12 35 13 14 27 8 51 38.5 52.5 M6 x 1 6 21 16 4
50 32 18 35 65 46.5 20 13 40 14 15.5 27.5 11 58 45 59 M8 x 1.25 7 21 16 5
63 32 18 35 75 56.5 20 13 45 14 16.5 28.5 11 58 50 64 M8 x 1.25 7 21 16 5
80 37 22 40 95 72 25 16 45 20 19 37 13 72 62 76.5 M10 x 1.5 10 30 16 5
100 37 26 40 114 89 30 16 55 20 19 37 16 72 71.5 86 M10 x 1.5 10 30 16 5
-Wl
Bore size
[mm] MM MO N NB P RF S V W WL ZZ S ZZ
32 M10 x 1.25 15 27 35 1/8 11 92 4 6.5 24 143 100 151
40 M14 x 1.5 19 27 40 1/4 11 97 4 9 24 152 110 165
50 M18 x 1.5 19 31.5 43.5 1/4 11 106 5 10.5 24 168 118 180
63 M18 x 1.5 19 31.5 43.5 3/8 11 106 9 12 24 168 118 180
80 M22 x 1.5 23 38 56 3/8 21 132 11.5 14 40 208 150 226
100 M26 x 1.5 23 38 56 1/2 21 132 17 15 40 208 150 226
420
With Mounting Bracket

Axial foot: (L) / Locking at head end: (-Hl) Cushion valve Port
CJ1
LY
4 x øLD
LH
CJP
Y X X Y LX
CJ2
LS + Stroke LZ
ZZ + Stroke
JCM
-Hl/-Rl [mm] -Wl
Bore size
CM2
[mm]
X Y LD LH LS LT LX LY LZ ZZ LS ZZ
32 22 9 7 30 136 3.2 32 53 50 170 144 178 CM3
40 24 11 9 33 145 3.2 38 59 55 183 158 196
50 27 11 9 40 160 3.2 46 72.5 70 202 172 214 CG1
63 27 14 12 45 160 3.6 56 82.5 80 205 172 217
80 30 14 12 55 192 4.5 72 102.5 100 248 210 266 CG3
100 32 16 14 65 196 4.5 89 122 120 252 214 270
JMB
Rod flange: (F) / Locking at head end: (-Hl)
Cushion valve
MB
4 x øFD Port
MB1
CA2
øFd
FB
FY
CS1
FE FT FX
FZ
CS2
-Hl/-Rl/-Wl [mm]
Bore size
[mm]
FB FD FE FT FX FY FZ Fd
32 50 7 3 10 64 32 79 25
40 55 9 3 10 72 36 90 31
50 70 9 2 12 90 45 110 38.5
63 80 9 2 12 100 50 120 39.5
80 100 12 4 16 126 63 153 45
100 120 14 4 16 150 75 178 54
Head flange: (G) / Locking at head end: (-Hl)

Cushion valve
4 x øFD Port
FB
FY
FT FX
ZZ + Stroke FZ
-Hl/-Rl [mm] -Wl

Bore size
[mm]
FB FD FT FX FY FZ ZZ ZZ
32 50 7 10 64 32 79 149 157 D-
40 55 9 10 72 36 90 158 171
50 70 9 12 90 45 110 176 188
-X
63 80 9 12 100 50 120 176 188
80 100 12 16 126 63 153 220 238 Technical
100 120 14 16 150 75 178 220 238 Data
421
MBB Series
With Mounting Bracket

Single clevis: (C) / Locking at head end: (-Hl) Cushion valve
Port
CDH10
U
L RR CX
Z + Stroke
ZZ + Stroke
-Hl/-Rl [mm] -Wl

Bore size
[mm]
L RR U CDH10 CX-0.1
-0.3 Z ZZ Z ZZ
32 23 10.5 13 10 14 162 172.5 170 180.5
40 23 11 13 10 14 171 182 184 195
50 30 15 17 14 20 194 209 206 221
63 30 15 17 14 20 194 209 206 221
80 42 23 26 22 30 246 269 264 287
100 42 23 26 22 30 246 269 264 287
Double clevis: (D) / Locking at head end: (-Hl)

Cushion valve Port
CDH10
U
L RR CX
Z + Stroke CZ
ZZ + Stroke
-Hl/-Rl [mm] -Wl

Bore size
[mm]
L RR U CDH10 CX+0.3
+0.1 CZ Z ZZ Z ZZ
32 23 10.5 13 10 14 28 162 172.5 170 180.5
40 23 11 13 10 14 28 171 182 184 195
50 30 15 17 14 20 40 194 209 206 221
63 30 15 17 14 20 40 194 209 206 221
80 42 23 26 22 30 60 246 269 264 287
100 42 23 26 22 30 60 246 269 264 287
Center trunnion: (T) / Locking at head end: (-Hl)

Z + 1/2 stroke Cushion valve Port
øTDe8
TY
TX
TT TZ
-Hl [mm] -Rl/-Wl

Bore size
[mm]
TDe8 TT TX TY TZ Z Z
32 12 17 50 49 74 89 97
40 16 22 63 58 95 93 106
50 16 22 75 71 107 105 117
63 20 28 90 87 130 105 117
80 20 34 110 110 150 129 147
100 25 40 132 136 182 129 147
422
Cautions for Using
1. Use recommended pneumatic circuit. 4. Relationship with cushion

Caution Caution
For correct operation of locking or releasing mechanism, use the following When cushion valve at side with locking mechanism is fully closed or nearly CJ1
pneumatic circuit. fully closed, piston rod may not reach the stroke end. Thus lock is not
established. And when locking is done with the cushion valve nearly fully
W closed, adjust the cushion valve since lock may not be released. CJP
CJ2
5. Release of lock
Warning JCM
When lock is to be released, supply air pressure to the port without the
locking mechanism, this relieves the load from the lock mechanism. CM2
(Refer to recommended pneumatic circuit.) When port without lock
mechanism is exhausted and locking mechanism is loaded, the lock may be
W damaged due to excessive force on lock during release. Also, piston rod will CM3
With locking at head end With locking at rod end operate immediately.
q Do not use a 3-position solenoid valve. CG1
Avoid using circuit with 3-position solenoid valve (especially closed center, 6. Manual release CG3
metal seal type).
When pressure is trapped in the port with locking mechanism, end lock is free. Caution
When utilizing a 3-position closed center valve, even if the lock is engaged, it Non-locking type JMB
may become unlocked due to pressure leakage either across the piston or the Insert attached bolt from upper side of rubber cover (no need to remove
rubber cover), tighten locking piston and pull bolt, lock will be released.
valve spool.
When bolt is released, locking begins to take place. Thread size, required MB
pulling force and stroke are listed below.
w Back pressure is required to release lock. MB1
Before starting operation, supply air to side without locking mechanism as figure Bore size [mm] Thread size Pulling force Stroke [mm]
above, (or side without locking the piston rod for models with locking at both 32 ≥ M2.5 x 0.45 x 25 L 4.9 N 2 CA2
ends.) Otherwise, lock may not be released. (Refer to “Release of lock”.) 40, 50, 63 ≥ M3 x 0.5 x 30 L 10 N 3
80, 100 ≥ M5 x 0.8 x 40 L 24.5 N 3
* Remove bolt under normal operations.
CS1
e Release lock when mounting or adjusting the cylinder.
It may cause malfunction of locking and release.
If mounting is done with lock engaged, lock may be damaged. CS2
Rubber cover
r Use with load 50% or less of rated capacity.
If cylinder is used over 50% load capacity, lock may be damaged.
t Do not use multiple cylinders synchronously.

Avoid using 2 or more end lock cylinders synchronously to perform a single
task because one of the cylinders may not allow lock to release.
y Use a speed controller as meter-out.

Meter-in control may not allow lock to release.
Locking type
Turn 90° counterclockwise while pushing the M/O knob. Lock is released when
u Use complete stroke or cylinder at side with lock. G on the cap and H OFF mark on the M/O knob correspond. (Lock remains
If cylinder piston does not reach end of stroke, lock may not be engaged or released.)
released. When locking is desired, turn 90° clockwise while fully pushing the M/O knob
and correspond G on the cap and H ON mark on the M/O knob. Confirm the
correct position by click sound “click”. Otherwise, lock may not be engaged.
2. Operating pressure
Lock
Caution Release
Use pressures 0.15 MPa or more at port with locking mechanism. Otherwise,
lock will not be released.
3. Exhaust speed
Caution
When pressures at port with locking mechanism is decreased to 0.05 MPa D-
or less, it is automatically locked. When exhaust pipe at port with locking
mechanism is thin and long or speed controller is distanced from cylinder -X
port, exhaust speed is slow and will require additional time for lock
engagement. Clogging the silencer mounted on exhaust port of solenoid Technical
valve leads to the same result. Locked Released Data
423
Air Cylinder: Low Friction Type
MBlQ Series RoHS
ø32, ø40, ø50, ø63, ø80, ø100

Use the new series “Smooth Cylinder
MBY Series” to realize bi-directional
low friction and low-speed operation.
(Refer to the Best Pneumatics No.w-3.)
How to Order
MB L Q 32 50 F
With auto switch MDB L Q 32 50 F M9BW
With auto switch Made to Order
(Built-in magnet)
Mounting type Number of auto switches

B Basic Nil 2 pcs.
L Axial foot S 1 pc.
F Rod flange 3 3 pcs.
G Head flange n “n” pcs.
C Single clevis
D Double clevis
T Center trunnion
Auto switch
Nil Without auto switch
Built-in Magnet Cylinder Model Bore size

If a built-in magnet cylinder without an 32 32 mm
auto switch is required, there is no need 40 40 mm
to enter the symbol for the auto switch. 50 50 mm Direction of low friction
(Example) MDBBQ40-100 63 63 mm F With pressure at head side
80 80 mm B With pressure at rod side
100 100 mm
Port thread type Cylinder stroke [mm]

Nil Rc
TN NPT
TF G
424
MB Series
Auto Switch Mounting
Auto Switch Proper Mounting Position (Detection at stroke end) and Its Mounting Height
<Band mounting> <Tie-rod mounting>
D-G39/K39/A3 D-M9/M9V D-Y59/Y69/Y7P/Y7PV CJ1
D-M9W/M9WV D-Y7W/Y7WV/Y7BA
D-M9A/M9AV D-Z7/Z80 CJP
D-A9/A9V
CJ2
Auto switch ≈ Hs Auto switch ≈ Hs
JCM
≈ Ht
≈ Ht
CM2
A B A B
CM3
CG1
D-A44 D-A5/A6
D-A59W CG3
Auto switch ≈ Hs Auto switch ≈ Hs JMB
MB
≈ Ht
≈ Ht
MB1
A B A B
CA2
D-F5/J59 CS1
D-F5W/J59W/F5BA
D-F59F/F5NT CS2
Auto switch ≈ Hs
≈ Ht
A B
D-P3DWA
Auto switch ≈ Hs
≈ Ht
A B
D-P4DW
Auto switch ≈ Hs
≈ Ht
D-
A B
-X
Technical
Data
425 A
MB Series
Auto Switch Proper Mounting Position (Standard type) [mm]
Auto D-Y59l
switch D-Y69l
model D-M9l D-Y7P
D-M9lV D-F5l D-G39
D-M9lW D-A9l D-A5l D-K39 D-Y7PV
D-J59 D-F5NT D-A59W D-A3l D-Y7H D-P3DWA D-P4DW
D-M9lWV D-A9lV D-A6l
D-Y7lW
D-M9lA D-F59F D-A44
D-Y7lWV
D-M9lAV D-Z7l
Bore D-Z8l
size A B A B A B A B A B A B A B A B A B A B
32 10 8 6 4 6.5 4.5 11.5 9.5 0 0 4 2 0 0 3.5 1.5 5.5 3.5 3 1
40 9 9 5 5 5.5 5.5 10.5 10.5 0 0 3 3 0 0 2.5 2.5 4.5 4.5 2 2
50 10 9 6 5 6.5 5.5 11.5 10.5 0 0 4 3 0 0 3.5 2.5 5.5 4.5 3 2
63 10 9 6 5 6.5 5.5 11.5 10.5 0 0 4 3 0 0 3.5 2.5 5.5 4.5 3 2
80 14.5 11.5 10.5 7.5 11 8 16 13 4.5 1.5 8.5 5.5 4.5 1.5 8 5 10 7 7.5 4.5
100 14 12 10 8 10.5 8.5 15.5 13.5 4 2 8 6 4 2 7.5 5.5 9.5 7.5 7 5
125 16 16 12 12 12.5 12.5 17.5 17.5 6 6 10 10 6 6 9.5 9.5 11.5 11.5 9 9
∗ Models with rubber bumper have different dimensions for auto switch proper mounting positions (A and B). Add the following values to both
A and B: 3 mm (ø32 and 40), 4 mm (ø50 and 63), 5 mm (ø80 and 100), 6 mm (ø125).
Note) Adjust the auto switch after confirming the operating conditions in the actual setting.
Auto Switch Proper Mounting Height (Standard type) [mm]

Auto D-F5l
switch D-Y59l
D-J59
model D-M9l D-M9lV D-A5l D-Y7P
D-M9lW D-F59F D-G39 D-Y7lW D-Y69l
D-A9lV D-M9lWV D-F5lW D-A6l D-K39 D-A44 D-P3DWA D-P4DW
D-M9lA D-M9lAV D-J59W D-A3l D-Y7BA D-Y7PV
D-Y7lWV
D-A9l D-A59W D-Z7l
D-F5BA D-Z80
Bore D-F5NT
size Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht
32 24.5 23 27.5 23 30.5 23 32.5 25 35 24.5 67 27.5 77 27.5 25.5 23 26.5 23 38 31 38 31
40 28.5 25.5 31.5 25.5 34 25.5 36.5 27.5 38.5 27.5 71.5 27.5 81.5 27.5 29.5 26 30 26 39 25.5 42 33
50 33.5 31 36 31 38.5 31 41 34 43.5 34.5 77 — 87 — 33.5 31 34.5 31 43 31 46.5 39
63 38.5 36 40.5 36 43 36 46 39 48.5 39.5 83.5 — 93.5 — 39 36 40 36 48 36 51.5 44
80 46.5 45 49 45 52 45 52.5 46.5 55 46.5 92.5 — 103 — 47.5 45 48.5 45 56.5 45 58 51.5
100 54 53.5 57 53.5 59.5 53.5 59.5 55 62 55 103 — 113.5 — 55.5 53.5 56.5 53.5 64.5 53.5 65.5 60.5
125 65.5 64.5 68.5 64.5 71 64.5 70.5 66.5 71.5 66.5 115 — 125 — 67.5 65 68.5 65 76 64.5 76.5 72
A 426
Auto Switch Mounting MB Series
Auto Switch Proper Mounting Position (Non-rotating rod type, With end lock) [mm]
Auto D-Y59l
switch D-Y69l
model D-M9l D-Y7P
D-M9lV D-F5l D-G39
D-Y7PV
D-M9lW D-A9l D-F5NT D-A5l D-A59W D-K39 CJ1
D-M9lWV D-A9lV D-J59 D-A6l D-A3l D-Y7H D-P3DWA D-P4DW
D-M9lA D-F59F D-A44 D-Y7lW
D-M9lAV D-Y7lWV
D-Z7l
CJP
D-Z8l
Bore
size A B A B A B A B A B A B A B A B A B A B CJ2
32 10.5 8 6.5 4 7 4.5 12 9.5 0.5 0 4.5 2 0.5 0 4 1.5 5.5 3.5 3.5 1
40 10.5 8 6.5 4 7 4.5 12 9.5 0.5 0 4.5 2 0.5 0 4 1.5 6 3.5 3.5 1 JCM
50 11 8.5 7 4.5 7.5 5 12.5 10 1 0 5 2.5 1 0 4.5 2 6.5 4 4 1.5
63 11 8.5 7 4.5 7.5 5 12.5 10 1 0 5 2.5 1 0 4.5 2 6.5 4 4 1.5 CM2
80 14 12.5 10 8.5 10.5 9 15.5 14 4 2.5 8 6.5 4 2.5 7.5 6 9.5 8 7 5.5
100 14 12.5 10 8.5 10.5 9 15.5 14 4 2.5 8 6.5 4 2.5 7.5 6 9.5 8 7 5.5 CM3
∗ Models with rubber bumper have different dimensions for auto switch proper mounting positions (A and B). Add the following values to both
A and B: 3 mm (ø32 and 40), 4 mm (ø50 and 63), 5 mm (ø80 and 100). CG1
Note) Adjust the auto switch after confirming the operating conditions in the actual setting.
CG3
Auto Switch Proper Mounting Height (Non-rotating rod type, With end lock) [mm] JMB
Auto D-F5l
switch D-J59
D-Y59l MB
model D-M9l D-M9lV D-A5l D-Y7P
D-M9lW D-F59F D-G39 D-Y7lW D-Y69l
D-M9lA
D-A9lV D-M9lWV D-F5lW
D-M9lAV D-J59W
D-A6l
D-A59W
D-K39
D-A3l
D-A44
D-Y7BA D-Y7PV
D-Y7lWV
D-P3DWA D-P4DW MB1
D-A9l D-Z7l
D-F5BA D-Z80
Bore D-F5NT CA2
size Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht Hs Ht
32 24.5 23 27.5 23 30.5 23 32.5 25 35 24.5 67 27.5 77 27.5 25.5 23 26.5 23 38 31 38 31 CS1
40 28.5 25.5 31.5 25.5 34 25.5 36.5 27.5 38.5 27.5 71.5 27.5 81.5 27.5 29.5 26 30 26 39 25.5 42 33
50 33.5 31 36 31 38.5 31 41 34 43.5 34.5 77 — 87 — 33.5 31 34.5 31 43 31 46.5 39 CS2
63 38.5 36 40.5 36 43 36 46 39 48.5 39.5 83.5 — 93.5 — 39 36 40 36 48 36 51.5 44
80 46.5 45 49 45 52 45 52.5 46.5 55 46.5 92.5 — 103 — 47.5 45 48.5 45 56.5 45 58 51.5
100 54 53.5 57 53.5 59.5 53.5 59.5 55 62 55 103 — 113.5 — 55.5 53.5 56.5 53.5 64.5 53.5 65.5 60.5
D-
-X
Technical
Data
427 A
MB Series
Minimum Stroke for Auto Switch Mounting

Mounting Brackets Except Center Trunnion n: Number of auto switches [mm]
Auto switch model Number of auto switches ø32, ø40, ø50, ø63 ø80, ø100 ø125 Note 2)
2 (Different surfaces, same surface)
15
1
D-M9l
D-M9lW (n − 2)
15 + 40 2
n
(n = 2, 4, 6, 8…) Note 1)
10
1
D-M9lV
D-M9lWV (n − 2)
10 + 30 2
n
(n = 2, 4, 6, 8…) Note 1)
15
1
D-M9lA (n − 2)
15 + 40 2
n
(n = 2, 4, 6, 8…) Note 1)
15
1
D-M9lAV (n − 2)
15 + 30 2
n
(n = 2, 4, 6, 8…) Note 1)
15
1
D-A9l (n − 2)
15 + 40 2
n
(n = 2, 4, 6, 8…) Note 1)
10
1
D-A9lV (n − 2)
10 + 30 2
n
(n = 2, 4, 6, 8…) Note 1)
2 (Different surfaces) 35
2 (Same surface) 100
D-G39 n (Different surfaces)
35 + 30 (n − 2)
D-K39 (n = 2, 3, 4…)
D-A3l 100 + 100 (n − 2)
n (Same surface)
(n = 2, 3, 4…)
1 10
2 (Different surfaces) 35
2 (Same surface) 55
35 + 30 (n − 2)
n (Different surfaces)
D-A44 (n = 2, 3, 4…)
55 + 50 (n − 2)
n (Same surface)
(n = 2, 3, 4…)
1 10
D-F5l 2 (Different surfaces, same surface) 15 25 25
D-J59
(n − 2) (n − 2) (n − 2)
D-F5lW 15 + 55 25 + 55 25 + 55 2
n (Same surface) 2 2
D-J59W (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1)
D-F5BA
D-F59F 1 10 25 25
15 20 20
1
D-A5l
D-A6l (n − 2) (n − 2) (n − 2)
15 + 55 2 20 + 55 2 20 + 55 2
(n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1)
2 (Different surfaces, same surface) 20 25 25
(n − 2) (n − 2) (n − 2)
20 + 55 2 25 + 55 2 25 + 55 2
D-A59W n (Same surface)
1 15 25 25
2 (Different surfaces, same surface) 15 25 30
(n − 2) (n − 2) (n − 2)
15 + 55 2 25 + 55 2 30 + 55 2
D-F5NT n (Same surface)
1 10 25 30
D-Y59l 2 (Different surfaces, same surface)
15
D-Y7P 1
D-Y7lW (n − 2)
D-Z7l 15 + 40 2
n
D-Z80 (n = 2, 4, 6, 8…) Note 1)
Note 1) When “n” is an odd number, an even number that is one larger than this odd number is used for the calculation.
Note 2) Non-rotating rod type and with end lock are applicable to ø32 to ø100.
428

Mounting Brackets Except Center Trunnion n: Number of auto switches [mm]
Auto switch model Number of auto switches ø32, ø40, ø50, ø63, ø80, ø100 ø125 Note 3)
D-Y69l 10
1
D-Y7PV (n − 2)
D-Y7lWV n
10 + 30 2
(n = 2, 4, 6, 8…) Note 1)
CJ1
1
20 CJP
D-Y7BA 20 + 45 2
(n − 2)
n
(n = 2, 4, 6, 8…) Note 1) CJ2
15
D-P3DWA
1
(n − 2) JCM
15 + 50 2
n
(n = 2, 4, 6, 8…) Note 1)
2 (Different surfaces, same surface) CM2
15 20
1
D-P4DW
n
15 + 65 2
(n − 2)
20 + 65 2
(n − 2)
CM3
(n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1)
Note 1) When “n” is an odd number, an even number that is one larger than this odd number is used for the calculation. CG1
CG3
Center Trunnion n: Number of auto switches [mm]
Auto switch model Number of auto switches ø32 ø40 ø50 ø63 ø80 ø100 ø125 Note 3) JMB
75 80 85 90 95 105
D-M9l 1
(n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
MB
D-M9lW 75 + 40 2 80 + 40 2 85 + 40 2 90 + 40 2 95 + 40 2 105 + 40 2
n
(n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) MB1
50 55 60 65 70 80
D-M9lV 1
(n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
CA2
D-M9lWV 50 + 30 2 55 + 30 2 60 + 30 2 65 + 30 2 70 + 30 2 80 + 30 2
n
(n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) CS1
80 85 90 95 100 110
1
D-M9lA (n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
CS2
80 + 40 2 85 + 40 2 90 + 40 2 95 + 40 2 100 + 40 2 110 + 40 2
n
(n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2)
55 60 65 70 75 85
1
D-M9lAV (n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
55 + 30 2 60 + 30 2 65 + 30 2 70 + 30 2 75 + 30 2 85 + 30 2
n
70 75 80 85 95 100
1
D-A9l (n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
70 + 40 2 75 + 40 2 80 + 40 2 85 + 40 2 95 + 40 2 100 + 40 2
n
45 50 55 60 70 75
1
D-A9lV (n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
45 + 30 2 50 + 30 2 55 + 30 2 60 + 30 2 70 + 30 2 75 + 30 2
n
Note 2) When “n” is an odd number, a multiple of 4 that is larger than this odd number is used for the calculation.
D-
-X
Technical
Data
429 C
MB Series

Center Trunnion n: Number of auto switches [mm]
Auto switch model Number of auto switches ø32 ø40 ø50 ø63 ø80 ø100 ø125 Note 3)
2 (Different surfaces) 60 65 75 80 85 90
2 (Same surface) 90 95 100 105 110 125
D-G39 n (Different surfaces)
60 + 30 (n − 2) 65 + 30 (n − 2) 75 + 30 (n − 2) 80 + 30 (n − 2) 85 + 30 (n − 2) 90 + 30 (n − 2)
D-K39 (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1)
D-A3l 90 + 100 (n − 2) 95 + 100 (n − 2) 100 + 100 (n − 2) 105 + 100 (n − 2) 110 + 100 (n − 2) 125 + 100 (n − 2)
n (Same surface)
1 60 65 75 80 85 90
2 (Different surfaces)
70 75 80 85 90
2 (Same surface)
70 + 30 (n − 2) 75 + 30 (n − 2) 80 + 30 (n − 2) 85 + 30 (n − 2) 90 + 30 (n − 2)
D-A44 (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1)
70 + 50 (n − 2) 75 + 50 (n − 2) 80 + 50 (n − 2) 85 + 50 (n − 2) 90 + 50 (n − 2)
n (Same surface)
(n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1) (n = 2, 4, 6, 8…) Note 1)
1 70 75 80 85 90
D-F5l/J59 2 (Different surfaces, same surface) 90 95 110 115 120 130
D-F5lW 90 + 55 2
(n − 4)
95 + 55 2
(n − 4)
110 + 55 2
(n − 4)
115 + 55 2
(n − 4)
120 + 55 2
(n − 4)
130 + 55 2
(n − 4)
D-J59W n (Same surface)
D-F5BA (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2)
D-F59F 1 90 95 110 115 120 130
2 (Different surfaces, same surface) 100 105 120 125 130 140
(n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
100 + 55 2 105 + 55 2 120 + 55 2 125 + 55 2 130 + 55 2 140 + 55 2
D-F5NT n (Same surface)
1 100 105 120 125 130 140
60 80 105 110 115
D-A5l 1
(n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
D-A6l 60 + 55 2 80 + 55 2 105 + 55 2 110 + 55 2 115 + 55 2
n (Same surface)
2 (Different surfaces, same surface) 60 70 85 110 115 120
(n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
60 + 55 2 70 + 55 2 85 + 55 2 110 + 55 2 115 + 55 2 120 + 55 2
D-A59W n (Same surface)
1 60 70 85 110 115 120
D-Y59l 2 (Different surfaces, same surface)
80 85 90 95 100 105
D-Y7P 1
D-Y7lW (n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
D-Z7l 80 + 40 2 85 + 40 2 90 + 40 2 95 + 40 2 100 + 40 2 105 + 40 2
n
D-Z80 (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2)
D-Y69l 60 65 70 75 85 85
1
D-Y7PV (n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
D-Y7lWV 60 + 30 2 65 + 30 2 70 + 30 2 75 + 30 2 85 + 30 2 85 + 30 2
n
85 90 100 105 110 115
1
D-Y7BA (n − 4) (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
85 + 45 2 90 + 45 2 100 + 45 2 105 + 45 2 110 + 45 2 115 + 45 2
n
80 85 90 95 100
1
D-P3DWA (n − 4) (n − 4) (n − 4) (n − 4) (n − 4)
80 + 50 2 85 + 50 2 90 + 50 2 95 + 50 2 100 + 50 2
n
120 130 140 150
1
D-P4DW (n − 4) (n − 4) (n − 4) (n − 4)
120 + 65 2 130 + 65 2 140 + 65 2 150 + 65 2
n
(n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2) (n = 4, 8, 12, 16…) Note 2)
Note 1) When “n” is an odd number, an even number that is one larger than this odd number is used for the calculation.
Note 2) When “n” is an odd number, a multiple of 4 that is larger than this odd number is used for the calculation.
A 430
Auto Switch Mounting Brackets/Part No.
Bore size [mm]

Auto switch model
ø32 ø40 ø50 ø63 ø80 ø100 ø125
D-M9l/M9lV
D-M9lW/M9lWV BMB5-032 BMB5-032 BA7-040 BA7-040 BA7-063 BA7-063 BA7-080
D-M9lA/M9lAV
D-A9l/A9lV
CJ1
D-A3l/A44
D-G39/K39
BMB2-032 BMB2-040 BMB1-050 BMB1-063 BMB1-080 BMB1-100 BS1-125 CJP
D-F5l/J59
D-F5lW/J59W CJ2
D-F59F/F5BA BT-03 BT-03 BT-05 BT-05 BT-06 BT-06 BT-08
D-F5NT
D-A5l/A6l/A59W JCM
D-P3DWA BA10-032S BA10-040S BA10-050S BA10-050S BA10-063S BA10-063S BA10-080S
D-P4DW BMB3T-040 BMB3T-040 BMB3T-050 BMB3T-050 BMB3T-080 BMB3T-080 BAP2T-080 CM2
D-Y59l/Y69l
D-Y7P/Y7PV
D-Y7lW/Y7lWV BMB4-032 BMB4-032 BMB4-050 BMB4-050 BA4-063 BA4-063 BA4-080 CM3
D-Y7BA
D-Z7l/Z80
CG1
[Stainless Steel Mounting Screw] • The figure shows the
The following stainless steel mounting screw kit (including set screws) is available. Use it in accordance with
the operating environment. (Since the auto switch mounting bracket is not included, order it separately.)
mounting example for the
D-M9l(V)/M9lW(V)/
CG3
BBA1: For D-A5/A6/F5/J5 types M9lA(V)/A9l(V).
Note 1) Refer to page 1689 for details on the BBA1. JMB
The above stainless steel screws are used when a cylinder is shipped with the D-F5BA auto
switch. When only one auto switch is shipped independently, the BBA1 is attached.
Note 2) When using the D-M9A(V) or Y7BA, do not use the steel set screws which are included with MB
the auto switch mounting brackets above (BMB5-032, BA7-, BMB4-, BA4-).
Order a stainless steel screw kit (BBA1) separately, and use the M4 x 6 L stainless steel set MB1
screws included in the BBA1.
CA2
CS1
CS2
Operating Range
[mm]
Bore size [mm] <Mounting example for ø32, D-P3DWA>
Auto switch model
32 40 50 63 80 100 125
D-M9l/M9lV Switch mounting bolt∗
D-M9lW/M9lWV 4 4.5 4.5 4.5 5 6 7
D-M9lA/M9lAV
D-Y59l/Y69l
D-Y7P/Y7lV 5.5 5.5 7 7.5 6.5 5.5 7
D-Y7lW/Y7lWV
D-Y7BA
D-F5l/J59
D-F5lW/J59W 3.5 4 4 4.5 4.5 4.5 5
D-F5BA/F5NT
D-F59F
D-G39/K39 9 9 9 10 10 11 11 * The switch mounting bolt is supplied with
D-P3DWA 3 4.5 4.5 5 5 5.5 6.5 the switch.
D-P4DW 4 4 4 4.5 4 4.5 4.5
D-A9l/A9lV 7 7.5 8.5 9.5 9.5 10.5 12
D-Z7l/Z80 7.5 8.5 7.5 9.5 9.5 10.5 13
D-A5l/A6l 9 9 10 11 11 11 10
D-A59W 13 13 13 14 14 15 17
D-A3l/A44 9 9 10 11 11 11 10
* Values which include hysteresis are for guideline purposes only, they are not a D-
guarantee (assuming approximately ±30% dispersion) and may change
substantially depending on the ambient environment.
-X
Technical
Data
431 A
MB Series
Other than the applicable auto switches listed in “How to Order”, the following auto switches are mountable.
Refer to pages 1575 to 1701 for the detailed specifications.
Type Model Electrical entry Features
D-M9NV/M9PV/M9BV
—
D-Y69A/Y69B/Y7PV
D-M9NWV/M9PWV/M9BWV Diagnostic indication
Grommet (Perpendicular)
D-Y7NWV/Y7PWV/Y7BWV (2-color indicator)
D-M9NAV/M9PAV/M9BAV Water resistant (2-color indicator)
D-P4DW Magnetic field resistant (2-color indicator)
D-F59/F5P/J59
Solid state
D-Y59A/Y59B/Y7P —
D-Y7H
D-F59W/F5PW/J59W Diagnostic indication
Grommet (In-line)
D-Y7NW/Y7PW/Y7BW (2-color indicator)
D-F5BA/Y7BA Water resistant (2-color indicator)
D-F5NT With timer
D-P5DW Magnetic field resistant (2-color indicator)
D-A93V/A96V —
Grommet (Perpendicular)
D-A90V Without indicator light
Reed
D-A53/A56/Z73/Z76 —
Grommet (In-line)
D-A67/Z80 Without indicator light
∗ With pre-wired connector is also available for solid state switches. For details, refer to pages 1648 and 1649.
∗ Normally closed (NC = b contact) solid state auto switches (D-F9G/F9H/Y7G/Y7H) are also available. For details, refer to pages 1593 and 1595.
432
MB Series
Made to Order: Individual Specifications
Please contact SMC for detailed dimensions, specifications and lead times.
Symbol
1 Cylinder with Heat Resistant Reed Auto Switch (−10 to 120°C) -X1184
Applicable Series
Description Model Action Note CJ1
Standard type MB Double acting, Single rod
CJP
How to Order
MDB Standard model no. Z – Pivot bracket Rod end bracket – Heat resistant reed auto switch – X1184 CJ2
Switch model
JCM
Symbol Description
Nil Without switch CM2
B30 D-B30
B30J D-B30J Number of switches CM3
B31 D-B31 Symbol Description
B31J D-B31J S 1 pc. CG1
B35 D-B35 Nil 2 pcs.
B35J D-B35J n n pcs.
CG3
Cylinder with heat resistant reed auto switch
JMB
∗ Refer to pages 1671 to 1673 for details about the D-B3 auto
switch and the Specific Product Precautions. MB
Specifications MB1
Ambient temperature range –10°C to 120°C
Bore size 40, 50, 63, 80, 100
Warning CA2
Seal material Fluororubber
Precautions
Grease Heat resistant grease Be aware that smoking cigarettes etc. after your hands have come into CS1
contact with the grease used in this cylinder can create a gas that is
hazardous to humans.
CS2
Dimensions (Dimensions other than below are the same as standard type.)
≈ Hs
59
42
RA 69 RB
S + Stroke
ZZ + Stroke
[mm]
Minimum mounting stroke Auto switch mounting bracket
Bore size S ZZ Hs RA RB part number
Other than center trunnion Center trunnion
40 99 154 57.5 2.5 14.5 200 st or more BMB2-040
1 pc.: 50 st or more
50 109 171 63 3.5 14.5 2 pcs.: Different surfaces 200 st or more BMB1-050
63 109 171 69.5 0.5 14.5 50 st or more 200 st or more BMB1-063
80 129 205 78.5 2.5 22.5 2 pcs.: Same surface 210 st or more BMB1-080
220 st or more
100 129 205 89 1 22 210 st or more BMB1-100
D-
-X
Technical
Data
433
MB Series
Specific Product Precautions
Be sure to read this before handling the products. Refer to back page 50 for Safety
Instructions and pages 3 to 12 for Actuator and Auto Switch Precautions.
Adjustment With Rod Boot
Warning Handling
1. Do not open the cushion valve beyond the stopper.
Crimping (ø32) or a retaining ring (ø40 to ø100) is provided to Caution
prevent the accidental removal of the cushion valve. Do not 1. Do not turn the piston rod with the rod boot kept
open the valve beyond the mechanism. If air is supplied, the locked.
cushion valve may shoot out from the cover. When turning the piston rod, loosen the band once and do not
twist the rod boot.
Bore size [mm] Cushion valve width across flats [mm] Hexagon wrench
JIS 4648
32, 40 2.5 Hexagonal wrench key 2.5
JIS 4648
50, 63 3
Hexagonal wrench key 3
JIS 4648
80, 100, 125 4 Hexagonal wrench key 4
2. Use the air cushion at the end of cylinder stroke.

Select the cylinder with bumper if the cushion valve is to be
fully opened. Otherwise, tie-rods or piston assembly may be
damaged.
2. Set the breathing hole in the rod boot downward or
3. When replacing mounting brackets, use a hexagon in the direction that prevents entry of dust or water
wrench. content.
Bore size [mm] Bolt Width across flats [mm] Tightening torque [N·m]
32, 40 MB-32-48-C1247 4 5.1
50, 63 MB-50-48-C1249 5 11
80, Foot MB-80-48AC1251

6 25
100 Others MB-80-48BC1251
Foot CE00008
125 8 30.1
Others CE00032
4. When replacing mounting brackets, tie-rod nuts on

the cylinder body become loosened.
After retightening the tie-rod nuts with the proper tightening
torque (Refer to Adjustment 3.), mount a mounting bracket.
5. Do not disassemble the trunnion type cylinder
because the mounting precision is required.
It is difficult to align the axial center of the trunnion with the
axial center of the cylinder. Thus, if this type of cylinder is
disassembled and reassembled, the required dimensional
accuracy cannot be attained, which may lead to malfunctions.
434

Xilanh SMC PDF

Uploaded by

Copyright:

Available Formats

Xilanh SMC PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Xilanh SMC PDF

Uploaded by

Copyright:

Available Formats

Air Cylinder

Example) MDB D -40-100Z- N V -M9BW

Various mounting bracket options

N: Trunnion pivot bracket

W: Double knuckle joint

N: Trunnion pivot bracket

Compact auto switches MB1

Non-rotating rod Rubber

Non-rotating rod Rubber

With end lock Rubber

Smooth Cylinder Double acting, Best Pneumatics

Use the new series “Smooth Cylinder MBY Series” -X

XB5 Oversized rod cylinder Note 6) v v v v v v v

XC22 Fluororubber seal v v v v v

MBK-Z MBB Note 6) MBY-Z Note 2) MBlQ Note 6)

ø32 to ø100 Symbol CJ2

Electrical Wiring Pre-wired Applicable

conduit 2-wire 12 V — K39 — — — — —

Grommet No 100 V or less A90 — V — V — — IC circuit

Bore size [mm] 32 40 50 63 80 100 125

Double clevis and double knuckle joint

Accessories Rod Boot Material

Mounting Brackets/Part No. Allowable Kinetic Energy

Load mass [kg]

Replacement Parts/Seal Kit

Water Resistant Air Cylinder

With rod boot

With Rod Boot [mm]

[mm] Rubber Bumper

Standard/With Mounting Bracket ∗ Refer to Basic (B) for other dimensions.

Axial foot: (L)

∗ Model without air cushion is designed to include rubber bumpers.

Standard/With Mounting Bracket ∗ Refer to Basic (B) for other dimensions.

Head flange: (G)

∗ Model without air cushion is designed to include rubber bumpers.

Single clevis: (C)

[mm] Rubber Bumper

∗ Model without air cushion is designed to include rubber bumpers.

Standard/With Mounting Bracket ∗ Refer to Basic (B) for other dimensions.

Double clevis: (D)

Hole dia.: CDH10

∗ Model without air cushion is designed to include rubber bumpers.

Center trunnion: (T)

Pivot Bracket/Trunnion and Double Clevis Pivot Bracket

Trunnion pivot bracket TE

Double clevis pivot bracket B

I-08M 80 80 26 40 60 M22 x 1.5 23.5 34 22 0

I-10M 100 80 26 40 60 M26 x 1.5 23.5 34 22+0.084

I-12M 125 119 36 46 92 M27 x 2 28.5 34 25+0.084

No. Appearance No. Appearance

Electrical Wiring Pre-wired Applicable

conduit 2-wire 12 V — K39 — — — — —

Bore size [mm] 32 40 50 63 80 100 125

For special port location (-XC3), the mounting

Replacement Parts/Seal Kit

With Rod Boot [mm]

Axial foot: (L)

MBK Series RoHS

ø32, ø40, ø50, ø63, ø80, ø100