Ac Boq

INDIAN INSTITUTE OF TECHNOLOGY BOMBAY REFURBISHMENT OF P.C. SAXENA AUDITORIUMINSIDE I.I.T.
B CAMPUS
SUMMARY
SR. NO. ITEM DESCRIPTION AMOUNT
I SUB STRUCTURE WORKS 0
II FINISHING WORK 0
III PLUMBING WORK 0
IV FIRE ALARM SYSTEM & PUBLIC ADDRESS SYSTEM 0
V ELECTRICAL WORK 0
VI HVAC WORK 0
TOTAL OF (I+II+III+IV+V+VI) 0
TENDER DOCUMENT BILL OF QUANTITIES SIGNATURE AND SEAL OF TENDERER

INDIAN INSTITUTE OF TECHNOLOGY BOMBAY REFURBISHMENT OF P.C. SAXENA AUDITORIUMINSIDE I.I.T.B CAMPUS
ITEMWISE SUMMARY
SR. NO. ITEM DESCRIPTION AMOUNT (RS.)
I SUB STRUCTURE WORKS
TOTAL OF EXCAVATION & EARTH WORKS 0
TOTAL OF PLAIN CEMENT CONCRETE 0
TOTAL OF REINFORCED CEMENT CONCRETE 0
TOTAL OF SUB STRUCTURE WORKS 0
II FINISHING WORK
TOTAL OF STEEL & ROOFING WORK 0
TOTAL OF DEMOLITION WORK 0
TOTAL OF BRICK WORK 0
TOTAL OF PLASTERING / PUNNING WORK 0
TOTAL OF FALSE CEILING WORK 0
TOTAL OF FLOORING, SKIRTING & DADO WORK 0
TOTAL OF PAINTING WORK 0
TOTAL OF DOOR WORKS 0
TOTAL OF WOOD WORKS (PARTITION & PANELLING) 0
TOTAL OF ALUMINUM WINDOW WORK 0
TOTAL OF MISCELLANEOUS WORKS 0
TOTAL OF FINISHING WORK 0

III PLUMBING WORK
TOTAL OF SANITARYWARES & CP APPURTENANCES 0
TOTAL OF WATER SUPPLY SYSTEM 0
TOTAL OF INTERNAL DRAINAGE SYSTEM 0
TOTAL OF PLUMBING WORK 0
IV FIRE ALARM SYSTEM & PUBLIC ADDRESS SYSTEM
TOTAL OF FIRE ALARM SYSTEM 0
TOTAL OF CABLES & ACCESSORIES 0

TOTAL OF FIRE ALARM SYSTEM & PUBLIC ADDRESS SYSTEM
0
WORK
V ELECTRICAL WORK
TOTAL FOR POINT WIRING IN PVC CONDUIT, TELEPHONE WIRING, T.V

0
WIRING ETC.
TOTAL OF LIGHT FIXTURES AND FITTINGS, CEILING FANS, EXHAUST
0
FANS ETC
TOTAL FOR POWER POINT WIRING 0
TOTAL FOR UPS SYSTEM 0
TOTAL OF DISTRIBUTION BOARDS 0
TOTAL FOR L.T.CABLES, END JOINTS 0
TOTAL OF EARTHING SYSTEM 0
TOTAL OF ELECTRICAL WORK WORK 0
VI HVAC WORK 0
GRAND TOTAL OF (I+II+III+IV+V+VI) 0

GENERAL IMPORTANT NOTES APPLICABLE TO THIS CONTRACT

(APPLICABLE TO CIVIL, FINISHING, PHWORKS, FIRE FIGHTING, ELECTRICAL WORKS, IBMS & HVAC
1 In addition to Clause 3.5.2 of Special Conditions of Contract Rate quoted for the items shall also be in
a) The tenderer shall provide barricade consisting of MS angle/pipe posts runners, bracing & corruga
separate the working area, maintaining the barricade in good condition including removing the same
any cost to IITB.
b) Statutory traffic regulations inforce shall be considered for transporting material, labour etc and no
account of the restrictions imposed by the local statuary authorities. Royalty charges for excavation a
other materials
c) Transporting of material ,labour , machinery etc to all heights & including locations of where direc
including arranging own arrangement
e) Security Regulations & rules of I.I.T, and its constituent units shall be strictly followed while movem
work forces and Cost arising due to security regulations.
g) Scaffolding to be provided for execution , shall be of Independent Scaffold Conforming to IS 2750
h) Safety of Labours working at site shall be as per safety code enclosed in the specifications and to
safety engineer.
2 Cement for structural works shall be OPC/PPC ISI marked and duly approved by the Engineer-in-ch
3
PPC/blended cement of ISI marked shall only be used for finishing works on prior approval of Engin
4 The approach road should be kept clean & free from obstructions for smooth functioning of existing tr
be made good without any extra cost to the IITB.
5 Tenderer's are advised to acquaint themselves with access to site, location of work, local labour prob
to availability and carriage of construction materials.
TENDER DOCUMENT BILL OF QUANTITIES - 4 SIGNATURE AND SEAL OF TENDERER

Signature of tend

Sr. No. Description Unit Qty

I SUB STRUCTURE WORKS
A EXCAVATION & EARTH WORKS
1 Earth work excavation by mechanical means / labour means for foundation pits,
trenches etc. in all types of soils other than soft and hard rock up to depths
mentioned below including shoring, dressing the sides, trimming, ramming and
preparing the bed for foundation and disposing of the surplus earth within a
distance of 150 meters etc. complete as per specifications, drawings & as directed
by the EIC.
1.1 Depth not exceeding 1.50 m. from ground level. Cum 80.00
2 Disposing off the surplus excavated materials by mechanical transport lead up to
2 KM to the nearby dumping pits/ dumping areas with in IITB campus identified
by Engineer in charge , including all lifts, loading, unloading, stacking etc.
complete as per specifications & as directed by the EIC.
2.1 All type of Soil Cum 40.00

3 Refilling around basement, foundation and in plinth with available murrum / Cum 25.00
excavated earth / Demolished structure debris / selected earth approved by
Engineer-in-charge excavated from nearby borrow areas including all leads up to
2 Km, lifts, loading, unloading, stacking, leveling, spreading, in layers not
exceeding 150 mm thick, watering, compaction to give 95% proctor density etc.
complete as per specifications, drawings & as directed by the EIC.
4 Supplying and spreading pesticides CHLORPYRIPHOS or other chemical

approved by central insecticides Board as directed by the manufacturer and
spraying the mixture uniformly by sprayer as pre-construction antitermite
treatment at the rate of 7.5 liters (or as directed by the manufacturer ) per sqm on
vertical and 5 liters. per sqm on horizontal surfaces of the sub-structure, within
the trenches, 50% of the emulsion to be filled in the holes made in trenches at
150 mm center to center etc. complete all as per IS 6313 Part-II(latest)
specification & as directed by the Engineer-in-charge. (The payment will be made
on the basis of plinth area measurement only aground floor/stilt area for all
stages of operation and vertical faces will not be measured for payment).
The contractor shall have to furnish ten years guarantee in the prescribed Sqmt 15.00
Performa (Appendix 'E') to maintain the anti-termite treated area /structure free
from termite.
5 Providing and laying dry rubble stone hard core soling of 230mm consolidated
thickness in sub base to floor and in plinth protection to required levels and lines
with first quality rubble, hand set, well packed including filling the interstices with
smaller stone chips, supplying & finishing/blinding the surfaces with approved
blinding quality murrum including watering, consolidation etc. complete as per
specifications, drawings & as directed by EIC.
5.1 230 mm thick with contractor supply of stone Sqm. 20.00


TOTAL OF EXCAVATION & EARTH WORKS
B PLAIN CEMENT CONCRETE

6 Providing and laying of plain cement concrete as leveling course for foundation,
basement, vertical surfaces of soil retention system and all locations depth with
Ready Mixed Concrete conforming to IS 4926 (latest revision) Plain cement
concrete grade M : 15 conforming to IS 456-2000 as per specifications
manufactured in fully automatic batching plant and transported to site of work,
having continuous agitated mixer, manufactured as per mix design of specified
grade for Plain cement concrete work , including lead from manufacturer site to
site of work, pumping of R.M.C from transit mixer to site of laying, cost of
admixtures in recommended proportions as per IS 9103 (latest) to accelerate /
retard setting of concrete, improve workability without impairing strength and
durability, mechanical conveying, placing in position mechanical compaction,
finishing, curing, scaffolding including necessary form work, consolidation,
finishing, curing etc. complete as per specifications ,drawings and as directed by
the Engineer-in-charge.
(Note :- 1) Prior approval of Engineer in charge for the supplier of RMC to be

taken.
2) On prior approval of Engineer-in-charge Fly ash conforming to Grade I of IS
3812 (Part I) may be used as part replacement of OPC provided uniform blending
with cement is ensured in accordance with Clauses 5.2 and 5.2.1 of IS 456 - 2000
in the items of BMC and RMC)
6.1 Cum 12.00

Foundation Plain cement concrete of Grade M-15
TOTAL OF PLAIN CEMENT CONCRETE
C REINFORCED CEMENT CONCRETE


7 a) All RCC shall be as specified and shall be carried out strictly in accordance
with the drawings and specifications.
b) The rates for RCC works shall be inclusive of all depths below G.L slabs at
all heights as detailed in the drg but exclusive of cost of reinforcement unless
otherwise mentioned.
c) All coarse aggregate to be 20 mm maximum size and uniformly graded
unless otherwise mentioned.
d) For all RCC items, the rates quoted shall include the following without any
extra cost to the Dept.
i) Spacers to maintain clear cover for reinforcement.
ii) Fixing at correct level & in proper alignment the inserts, pipe sleeves, pipe
bends, fan hooks, other pipe specials etc. supplied by Department or
Contractor unless otherwise mentioned in a separate item
iii) Test for concrete shall be done as per IS 456-2000 and the cost of the testing
to be carried out shall be borne by the contractor.
d) Precaution to be taken to avoid uplifting forces on the raft of water tanks.
As per the soil report, water table is expected near the ground level and
contractor is advised to use following sequence during concreting of the water
tank.
1) Dewatering to keep the area dry during construction.
2) Plum concrete to be completed as shown in the drawing.
3) Backfilling in layers and compaction for full height of the backfill as directed by
the EIC, over the raft projection.
4) Keeping the tank filled with water for at least half the depth.
Reinforced cement concrete of M-20 grade of design mix concrete conforming to

IS 456-2000, at all depth & location and levels using graded stone aggregate of
20mm. and down graded including machine mixing, conveying, placing in
position, mechanical consolidation, finishing, curing, scaffolding, dewatering if
necessary complete all as per drawing & specifications, but excluding the cost of
form work and steel reinforcement (which shall be paid under relevant item)
7.1 For RCC work for all structural Members such as Raft , foundations , all types of Cum 12.00
Walls, Columns, Beams , Waffle beams, Slabs, Staircases , Pardis, drop pardis ,
parapets, chajjas, niches etc of any shapes, sizes , thickness and depths etc.
Grade of concrete :- M20
(Note :- Rate inclusive of all shapes, sizes, curves, slopes, thickness and depths
at all heights etc and No extra payment for shall be payable.)


8 Providing, erecting, fixing in position striking / removing and cleaning steel /
plywood or any other approved material shuttering and centering for formwork in
substructure at all depths for all geometrical shapes, as per details shown in
drawings and as required for specific design of formwork wherever specified,
including proper bracing, ties, anchors, bolts, nuts, washers, packing plates,
fasteners of adequately designed capacities, producing finished concrete
surfaces. at all locations including chamfers, splays, keys, wedges, props, rails,
bracings, brackets, cutting holes if specified for pipes etc. providing and applying
approved form oil on all surfaces of formwork coming in contact with concrete
including close hacking of all exposed concrete work wherever required to
receive other type of finishing after removal of form work, all materials, labour
etc.complete as per specifications, drawings and as directed by the Engineer-in-
Charge. (Area of formwork in contact with concrete shall only be measured for
payment and stop boards for construction joints will not be measured for
payment). Note : - Prior approval of Engineer - in - charge to be obtained for
clearance of form work for laying RCC.
For Foundation Area

8.1 Foundations, footings, bases of columns, etc. for mass Sqm. 5.00
concrete and Raft.
8.2 Columns of any size and shape. Sqm. 15.00
8.3 Lintels, beams, girders, bressumers and cantilevers etc complete. Sqm. 15.00
8.4 Suspended floors, roofs, landings, balconies and access platform. Sqm. 35.00
9 Reinforcement for RCC work including supplying, delivering and storing of

various diameters as required at site of work transporting, decoiling, straightening,
cutting, bending, placing in position at all depths, levels and binding with 18-20
gauge, soft drawn locations annealed steel binding wire complete as per
specifications and drawings. (Cost of binding wire shall be borne by the contractor
& binding wire shall not be measured for payment. Rate includes cost of tests of
materials by Contractor as specified in the Specifications and IS) and preparing
and obtaining prior approval of bar bending schedule .
9.1 Thermo Mechanically Treated bars of grade Fe-415 manufactured by MT 1.50

recommended list of manufacturers conforming to IS 1786 - latest revision as per
specifications of works and drgs.
TOTAL OF REINFORCED CEMENT CONCRETE
TOTAL OF SUB STRUCTURE WORKS
II FINISHING WORK
General Notes


a) Unless otherwise specified all individual items are deemed to include the cost
of required single or double scaffolding, staging as required and contractor shall
not be entitled for any extra/ separate compensation on account of the same.
b) The contractor shall provide at their own cost temporary tarpaulin screens for
the entire duration of the contract to cover the works under execution to avoid
spreading / flying of dust to the adjoining buildings/ areas.
c) 43/ 53 grade cement to be used in masonry / plaster / wet cladding / flooring

works shall be of approved make and in compliance with technical specifications.
Sand and stone aggregates shall be from approved source and in compliance
with the technical specifications.
d) The materials required for the following works shall be sorted out as per the
manufacturing dates & batches, approved samples & shades. Prestacking,
handling, rehandling, transporting within the site, stacking & protection of
materials approved and rejected materials (rejected materials shall be replaced),
confirming the net quantities selected for use. No extras shall be paid for all above
and the contractor shall allow for all such eventualities in the construction time
period. No material/ samples including their makes/ brands shall be procured/
appointed/ subcontracted for mock up or for execution as the schedule of
quantities without the prior approval of the client / Architect.
A STEEL & ROOFING WORK

Preparing shop drawings, obtaining consultant's approval, supplying, fabricating,
delivering at site, hoisting and fixing in position including all temorary staging and
supporting work and making all structural steel work in accordance with the
design, drawings prepared by the consultants. the rate of steel work shall include
1 coat of red oxide primer and 2 coats of enamal paint assembly, welding,
jointing, building up new sections using plates / rolled section,/chs/rhs cost of
fasteners , nuts, bolts and washers), pre-heating the sections to temperatures up
to 250ºC if thickness of the section is equal to or more than 25mm.and fabrication
out of the following types of structural steel material for trusses, purlins, girders,
brackets, etc. with connections using plates, channels and angles, gusset plate,
connection bolts, cleats, fasteners etc. as per drawing, steel conforming to IS:226
and IS:2062-Gr.A with minimum yield strength of 335 Mpa for plates.
(Fasteners,welding electrodes, consumables will not be paid seperately. Rates
inclusive of necessary tests as per technical specification)
10 For Deck slab, roof extension including cols trusses purlins, extension of existing MT 6.75
members , site welding etc


11 Rebaring by using various diameter 12mm to 25mm. Dia, hilti make chemical each 40.00
(Re-500) max.depth 300 mm.
12 Providing & Fixing in position Metal Decking Sheets ( Tata Bluscope/ inter arch Sqm. 30.00
roofing/ raj mohan roofing 0.7mm thk smart deck 51 @ 6.56 kg/sqm ) for
supporting RC Slab including eadge trims cutting, trimming, fixing, leak proffing of
joints etc. complete.
13 Providing & fixing STUD type shear connector 12mm dia Thermomechanically each 50.00
fixed,
14 Providing & fixing in position 12mm thk. of Shalitex board at various joints such as Sqm. 5.00
isolation joints at wall edge, and column junctions and sealing with Winsil-20
neutral base sealent manufactured by GE Silicon , as per manufacturer's
requirements ,etc. complete,
15 Providing and fixing in position Bare Galvalume sheets for Roof & Colour Coated Sqm. 300.00
Galvalume Sheet for Cladding, including providing necessary laps, Flashing
pieces, self tapping screws , EPDM washers, seam bolts, stitch rivets at overlap
and all other hardware, scaffolding Etc.Complete.
16 Same as item 15 above above using j hooks Sqm. 25.00
17 Providing and fixing in position GI gutter made from 1.22mm thick a GI Rmt. 35.00
sheet,moulded to shape as per detail drawing approximately 300mm wide and
average 300mm deep laid to slope all as per design. Including treating the joints
with rubber & watrerproofing compound etc. complete.
18 Providing & fixing in position flashing at the junction of roof sheet and existing wall Rmt. 32.00
19 Providing & fixing Hilti make anchor bolts (mechanical) Kg 20.00

20 Providing, fabricating and fixing 1020 mm high Bright MS railing (Bright steel Kg 1615.00
conforming to IS : 226 and IS : 2062 with minimum yield strength of 250
Mpa and upto 500 Mpa ) for balcony as per architectural drawing and
instructions. The system shall be consist with 100mm x100mm and 8mm thick
base plate fixed in RCC member with anchor bolt ( 3/8 size) c/c as per site
condition and given the drawing. The verticale meber shall be consist with 65 mm
nominal bore medium section and 1020 mm height Ms pipe welded to base plate
properly as per architectural drawing with 3nos. 65 mm nominal bore medium
section ms horizontal pipe including hand rail pipe @ 303 mm c/c properly,
including necessary hardware, anchor bolt, cutting, grinding, machining,
assembly, welding, jointing, drilling, grouting and cleaning etc. completed as per
the instructions of EIC/ Architect Rate also included providing and applying one
coat epoxy primer of MRF or equivalent and finish the railing with two coates of
approved quality enamel paint of MRF or equivalent etc. completed
21 Providing & Laying Non shrink grout of FOSROCK / Sunanda / Krishna / MYK Cum 1.00
Laticrete / Ardex Endura Make GP 2, under side of base plates etc at all locations
and heights
TOTAL OF STEEL & ROOFING WORK

B DEMOLITION WORK
22 Dismantling, Demolishing, Cutting, Breaking, Removing & Cleaning Existing Items
Carefully and Stacking the Materials at site or as Instructed including necessary
tool, tackles, machineries, requisite scaffolding, carting away debris from site time
to time or disposing the material as directed and specified by the Architect / Client
for the following Items. (The rate shall include all leads, lift and height)
22.1 Removing of existing Flooring in Green rooms, and Prefunction area etc. Sqm. 190.00
including bedding materials. (Refer Drw. No. I-200, I-201, I-202)
22.2 Removing of existing windows including window frames (Refer Drw. No. I-200, Sqm. 45.00
I-201, I-202)
22.3 Removing of existing Doors including door frames (Refer Drw. No. I-200, I- Sqm. 45.00
201, I-202)
22.4 Remove and salvage door for refurbishment & refixing (Refer Drw. No. I-200, I- Sqm. 10.00
201, I-202)
22.5 Removing of existing partitions on stage (Refer Drw. No. I-200, I-201, I-202) Sqm. 50.00
22.6 Removing existing internal plaster with racking out the masonry joints. (Refer Sqm. 585.00
Drw. No. I-200, I-201, I-202)
22.7 Removing of existing Ms Grill,ventilators,aluminium frame ,glass with fixtures etc Sqm. 15.00
(Refer Drw. No. I-200, I-201, I-202)
22.8 Providing and doing core cutting in RCC slab at given location as per architectural Sqm. 5.00
instructions inluding necessary tools and machinaries, scaffolding, watering, rate
also included carting away the debris from site time to time or disposing the
material as directed and specified by the Architect / Client (Refer Drw. No. A-
200)
22.9 Removing of existing internal 100 mm thick brick work for green room partion. Sqm. 40.00
(Refer Drw. No. I-200, I-201, I-202)
(Refer Drw. No. I-200, I-201, I-202)
(Refer Drw. No. I-200, I-201, I-202)
22.12 Removing of existing wooden box for Duct in post Function (Refer Drw. No. I- Sqm. 15.00
200, I-201, I-202)
22.13 Removing of existing counter pre function area (Refer Drw. No. I-200, I-201, I- Rmt. 5.00
202)
22.14 Removing of existing curtains with pelmet in Auditorium (Refer Drw. No. I-200, Sqm. 125.00
I-201, I-202)
22.15 Removing of existing foundation stone and salvage with extreme care in pre each 2.00
function and post function area (Refer Drw. No. I-200, I-201, I-202)


22.16 Removing existing IPS in Auditorium area. (Refer Drw. No. I-200, I-201, I-202) Sqm. 245.00
22.17 Removing of existing screen with accessories & fittings (Refer Drw. No. I-200, Sqm. 50.00
I-201, I-202)
22.18 Removing of existing grid false ceiling with supports, framings, light fittings etc. Sqm. 375.00
(Refer Drw. No. I-200, I-201, I-202)
22.19 Removing of existing push back chairs (Refer Drw. No. I-200, I-201, I-202) each 399.00
22.20 Removing of existing roof with structural memebers in post function area. (Refer Sqm. 205.00
Drw. No. I-200, I-201, I-202)
22.21 Removing of existing corrugated sheet in post function area (Refer Drw. No. I- Sqm 370.00
200, I-201, I-202)
22.22 Removing of existing electical wirings, cables, fittings, boards, switches etc. Job 1.00
(Refer Drw. No. I-200, I-201, I-202)
22.23 Making cut outs in RC wall, with supporting steel frame etc Edge prepation to Cum 5.00
receive steel frame etc.. (str.steel frame qty, & anchor bolts, item will be paid
separetly in respective items (Refer Drw. No. A-200)
22.24 Removing of existing mosaic flooring in Auditorium (Refer Drw. No. I-200, I- Sqm. 155.00
201, I-202)
22.25 Removing of Wash basin with tap,bottle trap with all fixtures & supports. (Refer each 2.00
Drw. No. I-200, I-201, I-202)
22.26 Removing of existing Storage with all fixtures in Green room. (Refer Drw. No. I- Sqm. 10.00
200, I-201, I-202)
22.27 Removing of panel in post function area (Refer Drw. No. I-200, I-201, I-202)
Sqm. 20.00
22.28 Removing the existing stage flooring & sub base for flooring to place subwoofers
of approximate size 650mm x 650mm x 450mm and making good the same after
placing the subwoofers with capping using hard wood floor matching to the
Nos. 2.00
existing stage flooring etc complete as per the drawings and instructions of
Engineer - In - Charge
TOTAL OF DEMOLITION WORK 0.00

0.00
C BRICK WORK 0.00
23 Providing & doing well Burnt Brick masonary in all location with conventional type 0.00
bricks in cement mortar 1:4 in superstructure including striking joints, racking out
joints, watering, scaffolding and cleaning etc. complete Rate also included
providing & laying cast in situ rcc patali in M:150 at 1200mm c/c with 2nos 8mm
dia reinforcement including shuttering, deshuttering,curing, cleaning etc.
completed at all heights and satifaction to the EIC/ Architect.


23.1 150mm thick brick work in superstructure (Refer Drw. No. I-210, I-211, I-213, Sqm. 15.00
I-600A, I-600B, I-601,I-602A, I-602, I-603A, I-603B, I-605A, I-605B,I-
607A, I-607B, I-701, I-703, I-706, I-830)
607A, I-607B, I-701, I-703, I-706, I-830)
607A, I-607B, I-701, I-703, I-706, I-830)
24 Providing & Constructing Uncoursed rubble masonry of trap stones in cement Cum 75.00
mortar 1:6 in foundations and plinth ramp including through stones, corner
stones, pointing etc. including bailing out water, striking joints on exposed
faces and watering complete
TOTAL OF BRICK WORK 0.00
D PLASTERING / PUNNING WORK 0.00

25 Providing and applying avg. 12mm thk. (avg.) single coat internal plaster in Sqm. 585.00
cement sand mortar (1:4) for all plain / curved surfaces of brick / block / RCC
walls and finishing the same (smooth or broom) in correct line, level & plumb,
making of edges, corners, sill, jambs, soffits, grooves, pattas etc. as per drawings
& relevant specifications including all necessary surface preparation, scaffolding,
p/f of PVC chicken mesh of approved quality at all junctions of RCC & masonry
work, hacking of concrete surface to receive plaster, watering, curing, cleaning
etc. complete at all levels and heights. (Refer Drw. No. I-210, I-211, I-213, I-
600A, I-600B, I-601,I-602A, I-602, I-603A, I-603B, I-604A, I-604B, I-604C,
I-604D, I-604E,I-605A, I-605B, I-606, I-607A, I-607B, I-701,I-702, I-703, I-
705A, I-705B, I-706, I-830)
26 Providing and applying avg. 8mm thk. (avg.) single coat internal plaster in Sqm. 10.00
cement sand mortar (1:4) for all plain / curved Ceiling surfaces and finishing the
same (smooth or broom) in correct line & level, making of edges, corners, sill,
jambs, soffits, grooves, pattas etc. as per drawings & relevant specifications
including all necessary surface preparation, scaffolding, hacking of concrete
surface to receive plaster, watering, curing, cleaning etc. complete at all levels
and heights. (Refer Drw. No. I-210, I-211, I-213, I-600A, I-600B, I-601,I-
602A, I-602, I-603A, I-603B, I-604A, I-604B, I-604C, I-604D, I-604E,I-
605A, I-605B, I-606, I-607A, I-607B, I-701,I-702, I-703, I-705A, I-705B, I-
706, I-830)


27 Providing and applying avg. 13mm thk( avg.) POP plaster to walls using Sqm. 125.00
approved quality POP as per IS 2547-1976, over all plain / curved surfaces of
brick / block / RCC and to be finished smooth in correct line, level & plumb,
making of edges, corners, sill, jambs, soffits, pattas etc. as per drawings &
relevant specifications including all necessary surface preparation, making level
pads (Dada), scaffolding, hacking of surface to receive plaster, cleaning etc.
complete at all levels and heights. (Refer Drw. No. I-210, I-211, I-213, I-
600A, I-600B, I-601,I-602A, I-602, I-603A, I-603B, I-604A, I-604B, I-604C,
I-604D, I-604E,I-605A, I-605B, I-606, I-607A, I-607B, I-701,I-702, I-703, I-
705A, I-705B, I-706, I-830)
28 Providing and applying avg. 6mm thk. (avg.) POP to ceiling using approved Sqm. 10.00
quality pop as per IS 2547,1976 for all plain / curved surfaces, pattas finished
smooth in correct line & level including all necessary surface preparation, making
level pads (Dada), scaffolding, hacking of surface to receive plaster, cleaning etc.
complete as per relevant working drawings & specifications at all levels and
heights. (Refer Drw. No. I-210, I-211, I-213, I-600A, I-600B, I-601,I-602A,
I-602, I-603A, I-603B, I-604A, I-604B, I-604C, I-604D, I-604E,I-605A, I-
605B, I-606, I-607A, I-607B, I-701,I-702, I-703, I-705A, I-705B, I-706, I-
830)
29 Providing & laying POP of sufficient thickness over plastic sheets as a protective Sqm. 45.00
layer for flooring during the work including all maintenance, p/l plastic sheets,
removing & disposing POP after the use, cleaning, etc. complete at all floors & as
directed by the EIC. (Refer Drw. No. I-210, I-211, I-213, I-600A, I-600B, I-
601,I-602A, I-602, I-603A, I-603B, I-604A, I-604B, I-604C, I-604D, I-
604E,I-605A, I-605B, I-606, I-607A, I-607B, I-701,I-702, I-703, I-705A, I-
705B, I-706, I-709, I-830)
30 Providing and making Grooves of approved shape and size in POP at various 0.00
locations viz.above skirting, around the door & window frame,above dado or
wherever required as per the
drawing including finishing of groove in correct line and level, making of moulds
(farmas), cleaning, scaffolding etc. complete at all heights & floors. (Refer Drw.
No. I-210, I-211, I-213, I-600A, I-600B, I-601,I-602A, I-602, I-603A, I-
603B, I-604A, I-604B, I-604C, I-604D, I-604E,I-605A, I-605B, I-606, I-
607A, I-607B, I-701,I-702, I-703, I-705A, I-705B, I-706, I-830)
30.1 Groove up to 6 mm (Depth – 6mm) Rmt. 130.00

30.2 12mm groove (Depth – 6mm) Rmt. 40.00
TOTAL OF PLASTERING / PUNNING WORK 0.00
0.00
E FALSE CEILING 0.00
General Note 0.00


a) All types of false ceiling shall be inclusive of side profile, coves, grooves, 0.00
finishing etc.
31 Providing & fixing suspended false ceiling using 12.5mm thick Gypsum boards Sqm. 55.00
confirming to IS 2095-1982 and GI framework of Gyp steel or approved equivalent
as per architectural drawing and instructions comprising of following.
1. GI perimeter channel of 0.55mm thick having one flange of 20mm, another
of 30mm and web of 27mm fixed to brick wall partition along periphery of ceiling
with the help of nylon sleeves and screws at 610mm c/c
2. GI intermediate channel of size, 45mm web, two flanges each of 15mm &
thickness 0.9mm ) suspended from the soffit / ceiling at 600mm c/ c spacing.
3. GI ceiling sections of 0.55mm thick having knurled web of 51.5mm and two
flanges each of 26mm with leaves of 10.5mm fixed to intermediate channel with
the help of connecting clip at direction perpendicular to the intermediate channel
at spacing of 600 mm c/c,
4. GI suspender angle of 25mmx10mm and thk.0.55mm at spacing of 600mm
c/c, fixed to the ceiling / soffit using GI cleat angle 25mm x 25mm, 0.55mm thk.
Cleat angle to be fixed to the ceiling / soffit using 6mm dia anchor fastener.
Gyp boards with tapered edges to be screwed to the framework with 25mm long
GI screws at 230 mm c/c. Screw fixing shall be done mechanically. Gyp boards
are to be joined and finished so as to have a flush look which includes filling and
finishing the tapered and square edge of the boards with gypsum roller net tape &
approved quality joining compounds. The work also includes vertical drops,
curvature, providing & making farma cutting of gyp boards & frame work and
providing cutouts / openings and additional supports wherever required for the
fixing of ceiling fixtures like, lights, A.C grills, sprinklers, smoke detectors etc.
Refer Drw. No. I-210, I-211, I-213 I-300A, I-602A, I-602B, I-603A, I-603B,
I-703, A-202, A-501, A-502, I-830
(Mode of measurements : Only plan are of ceiling shall be measured for
payment)
32 Do as per item No.31 but for Gypsum patta in various sizes for ceiling. 0.00
Refer Drw. No. I-210, I-211, I-213, I-300A, I-602A, I-602B, I-603A, I-
603B, I-703, I-830
Mode of measurements : Only running length of patta shall be measured
for payment)
32.1 Up to 50mm wide patta. Rmt. 5.00

32.2 Above 50mm and up to 100mm patta. Rmt. 5.00


32.7 Above 300mm patta. Sqm. 10.00
33 Providing and fixing Decosonic CNBM MgO board false ceiling which includes Sqm. 170.00
G.I perimeter channels of size 0.55mm thk. (having one flange of 20mm and
another flange of 30mm and a web of 27mm) along with perimeter of ceiling
screw fixed to brick wall/partition with the help of nylon sleeves and screws, at
610mm centers Then suspending G.I intermediate channels of size 45mm
(0.9mm thk. With two flanges of 15mm each) from the sofit at 1220mm centers
with ceiling range of width 25mm x10mmx0.55mm thk fixed to sofit with G.i cleat
and steel expansion fasteners celling section of 0.55 mm thk having knurled web
of 51.5mm and two flanges of 26mm each with lips of 10.5 mm are then fixed to
the intermediate channel with the help of connecting clip and in direction
perpendicular to the intermediated channel at 457mm centers Decosonic CNBM
board of thickness 12mm is then screw fixed to ceiling section with 25mm drywall
screws at 230mm centers screw fixing is to be done mechanically either with
screw driver or drilling machine with suitable attachment.The boards shall have
Moisture Absorption 6.8% after 2 hours and 11.3% after 24 hours soaking,Wet
expansion < 0.02% from ambient to saturation,Dry Contraction < 0.02% from
ambient to evaporation.STRENGTH-Compressive Strength - 27.3
N/mm2,Flexural Strength - 10.87 N/mm2,Tensile Strength - 3.38 N/mm2,FIRE-
Fire Resistance < 180 minutes under 1200°C,BS476 Part 4 - Non-
combustible,Thermal Conductivity - 0.11792 W/m0K, with Green Building
application. (Mode of measurements : Only plan area of ceiling shall be
measured for payment)
34 Do as per item No. 33 but for CNBM MgO board patta in various sizes for ceiling. 0.00
Refer Drw. No. I-210,I-211, I-213, I-300A, I-600B, I-700, I-830 (Mode of
measurements : Only running length of patta shall be measured for
payment)
34.1 Up to 50mm wide patta. Rmt. 10.00

34.7 Above 300mm patta. Sqm. 15.00


35 Providing & fixing Accoustical Fabric Ceiling for Auditorium false ceiling as per Sqm. 200.00
architectural drawing and instructions. The system shall be comprise with
following Frame work - Providing and doing and fixing 16 guage 50 x 38 mm
aluminum frame for outer peripheri of false celing and P/f 16 guage 50 x 50mm
aluminum frame @ 600 mm c/c both direction, entire frame shall be fixed to main
ceiling with GI cleat angle 25mm x 25mm, 0.55mm thk. Cleat angle to be fixed to
the ceiling / soffit using 6mm dia anchor fastener @ 6000mm c/c. P/f ply frame
made out of 12mm thick 75mm patta @ 600mm c/c both direction. the frame shall
be fixed to aluminum frame properly. The accoustical false ceiling is at different
level and in shall be 150mm overlapped to each other and 12mm thick 200mm
wide commercial ply vertical patta fixed between two celing as per architectural
drawings Accoustic/ Fabric - Providing and fixing 40mm thick (Density 12
kg/cum and NRC Value 0.8) foam of Basotect or any other approved make fixed
in aluminum framework with 12 guage 38mm GI wire mash properly. Entire
frame work shall be finished with rapping approved color fabric (Bharat Furnishing
- Premium shade - 24293 - Sr. No. 6 Munar Silk / Decotex - VRN 817 Decotex -
VRN 818). Fabric should be fixed properly, avoid bubbles/ looseness in fabric as
per architectural drawings and instructions including making the . Cut out for light
fixtures & providing necessary GI frames to hang the same independently all
necessary hardware, scaffolding, cutting, drilling, screwing and cleaning etc.
Completed at all levels and heights and as specified by EIC/ Architect. Both sides
vertical pattas of false ceiling at longitudinal direction and end support shall be
included in the rate. (Mode of measurements : Only plan area of curve
ceiling shall be measured for payment)
36 Providing and fixing 20mm thick Black Straw board of Anutone or any other Sqm. 210.00
approved make. ( Strand square edge magnesite bonded wood fiber panels of
size 600x600x20mm having density 400kg/m3, weight 8kg.) for auditorium celing.
The panels shall be fixed directly to existing rcc ceiling with screw properly as per
architectural drawing and instruction. including necessary hardware, scaffolding,
drilling, cuting, filling the screw holes with putty or any other filler material and
finish the holes with paint matching to straw board andcleaning etc. completed at
at all levels and heights and as specified by EIC/ Architect Refer Drw. No. I-
210,I-211, I-213, 1-300A, I-300B, I-604A, I-604B, I-604C, I-604D,I-604E,
I-704, I-830 (Mode of measurements : Only plan are of ceiling shall be
37 Providing and making Grooves of approved shape and size in Gypsum/ MGO 0.00
Ceiling at various locations viz. above skirting, around the door & window frame,
above dado or wherever required as per the drawing including finishing of groove
in correct line and level, making of moulds (farmas), cleaning, scaffolding etc.
complete at all heights & floors. (Refer Drw. No.I-210, I-211, I-213 1-300A, I-
300B, I-604A, I-604B, I-604C, I-604D,I-604E, I-704, I-830)

37.1 groove up to 6 mm Rmt. 10.00
37.2 12mm groove Rmt. 10.00
TOTAL OF FALSE CEILING WORK 0.00

0.00
F FLOORING, SKIRTING & DADO WORK 0.00
Note: 0.00
1) White marble and Italian should be fixed in white cement. 0.00
2) All polishing shall be mirror polished unless otherwise specified. 0.00
38 Providing & Laying in position 32 mm avg. thick machine cut machine polished Sqm. 80.00
Kota Stone of approved size, quality, type & colour as per the approved sample
for Post function Flooring in approved shape and pattern in true line and level / to
required slope over average 50mm thick bedding of cement mortar (1:4) floated
with neat cement slurry / paste (cement @ 4.5 kg/sqm) including cutting to the
required sizes (up to 570mm x 570mm), surface preparation, providing & laying ,
filling & finishing the joints with neat cement slurry & approved colour pigments,
mirror polishing, watering curing, cleaning etc complete at all floors & levels as
per the instructions of the EIC. (Refer Drw No.I-210, I-211, I-213, I-605A, I-
605B, I-606,I-706, I-830, A-201, A-501, A-502, A-503, A-800) (Mode of
measurements : Only plan are of flooring shall be measured for payment)
39 Providing & Laying in position 32 mm thick machine cut Rough finished Kota Sqm. 20.00
Stone of approved size, quality, type & colour as per the approved sample for
Fire exit Ramp Flooring in approved shape and pattern in true line and level / to
required slope over average 50mm thick bedding of cement mortar (1:4) floated
with neat cement slurry / paste (cement @ 4.5 kg/sqm) including cutting to the
required sizes (up to 570mm x 570mm), surface preparation, providing & laying ,
filling & finishing the joints with neat cement slurry & approved colour pigments,
watering curing, cleaning etc complete at all floors & levels as per the instructions
of the EIC. Refer Drw No.-I-210, I-213, I-605A, I-605B, I-606,I-706, I-830,
A-201, A-501, A-502, A-503, A-800 (Mode of measurements : Only plan
are of flooring shall be measured for payment)
40 Doing mirror polishing to existing Kota Stone flooring Post function/Ramp/ Sqm. 245.00
pantry Flooring including all machinaries, kits, cleaning etc complete at all floors &
levels as per the instructions of the EIC. Refer Drw No.--I-210, I-211, I-213, I-
605A, I-605B, I-606,I-706, I-830, A-201, A-501, A-502, A-503, A-800
(Mode of measurements : Only plan are of flooring shall be measured for
payment)


41 Providing & Laying in position 19 mm thick machine cut Telephone Black Sqm. 80.00
Flamed finish Granite slab of approved size, quality, type & colour as per the
approved sample for Pre- Function Flooring/ Mid landing in approved shape
and pattern in true line and level / to required slope over average 50mm thick
bedding of cement mortar (1:4) floated with neat cement slurry / paste (cement @
4.5 kg/sqm) including cutting to the required sizes, surface preparation, providing
& laying , filling & finishing the joints with neat cement slurry & approved colour
pigments, watering curing, cleaning etc complete at all floors & levels as per the
instructions of the EIC. Refer Drw No.I-210, I-213, I-600A, I-601, I-701, I-
702, I-606, I-707, I-830 (Mode of measurements : Only plan are of
flooring shall be measured for payment)
42 Providing & Laying in position 19 mm thick machine cut Telephone Black Sand Sqm. 20.00
Blasted Granite slab of approved size, quality, type & colour as per the
approved sample for Pre- Function Flooring/ Mid landing in approved shape
and pattern in true line and level / to required slope over average 50mm thick
bedding of cement mortar (1:4) floated with neat cement slurry / paste (cement @
4.5 kg/sqm) including cutting to the required sizes, surface preparation, providing
& laying , filling & finishing the joints with neat cement slurry & approved colour
pigments, watering curing, cleaning etc complete at all floors & levels as per the
instructions of the EIC. Refer Drw No.I-210, I-211 I-213, I-600A, I-601, I-
701, I-702, I-606, I-707, I-830 (Mode of measurements : Only plan are of
flooring shall be measured for payment)
43 Providing & Laying in position full body Vitrified tiles of different sizes 0.00
(thickness to be specified by the manufacturers) of approved size, quality,
type & colour as per the approved sample for Flooring (conforming to IS 15622)
in approved shape and pattern in true line and level to required slope over
average 20mm thick bedding of cement mortar 1:4 (1 cement : 4 coarse sand)
floated with neat cement slurry / paste (cement @ 4.5 kg/sqm) including
chamfering of tiles wherever required, cutting to the required sizes, surface
preparation, providing & laying, grouting the joints with white cement & matching
pigments, watering, curing, cleaning etc complete at all floors & levels as per the
instructions of the EIC.
Refer Drw No.I-210, I-211 I-213, I-602A, I-602B, I-603A, I-603B, I-703, I-
830
(Mode of measurements : Only plan area of flooring shall be measured
for payment)
43.1 600mm x 600mm in size Vitrified tile for Green room VT 01) (Code No. SCPL- Sqm. 55.00
5286 Make - Sameer Ceramics/ Mirage- Vision Charcoal /).


44 Providing & Fixing in position skirting of following types using material as per 0.00
approved sample at all floor & levels fixed flush to the wall surface with cement
paste of desired consistency as per the pattern given to correct line, level & plumb
including chasing of wall / plaster wherever required, surface preparation, filling &
finishing the tile joints with cement & approved quality colour pigments, cutting of
tiles, mitering at edges, curing, cleaning, etc complete as per the instructions of
the EIC. 100mm high skirting with length of tile as per the architectural
drawings. (Mode of measurements : Only Running length of skirting shall
be measured for payment)
Refer Drw. No. I-210, I-211 I-213, I-602A, I-602B, I-603A, I-603B, I-703, I-
600A, I-601, I-701, I-702, I-606, I-707,I-830, I-605A, I-605B, I-606,I-706,
I-830, A-201, A-501, A-502, A-503, A-800
44.1 10mm thick Vitrified tile skirting (Code No. SCPL-5286 Make - Sameer Rmt. 60.00
Ceramics/ Mirage- Vision Charcoal /).
44.2 19 mm thk. Telephone Black flamed Granite skirting with top edge polish Rmt. 125.00
44.3 19 mm thk. Telephone Black sandblasted Granite skirting with top edge Rmt. 35.00
polish
44.4 19mm thk. Kota stone skirting with top edge polish. Rmt. 55.00
45 Providing and laying 1st quality Ceramic tiles for Dado at all heights and location 0.00
(CR 01) (thickness to be specified by the manufacturer) conforming to IS :
15622 of approved make and colour and pattern, in dado laid over 12mm thick
backing coat of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with
grey cement slurry @ 3.3kg per sqm including cost of backing coat pointing in
white cement and matching pigment, staging if required etc. complete all as per
specifications and drawings and as directed by Engineer In Charge.
Ref Drg no. I-210, I-211, I-213, I-606, I-707, I-830
45.1 600mm x 600mm in size Ceramic tile for Pantry/Green room Dado in (CR 01) Sqm. 45.00
(Crema Dun Make - Nitco/ RAK/ Kajaria)
45a Providing and laying 2nd quality ceramic matt finished wall tiles (SQT 01) at all Sqm. 8.00
heights and location behind storage i.e below pantry platform (thickness to be
specified by the manufacturer) conforming to IS : 15622 of approved make and
colour and pattern, in dado laid over 12mm thick backing coat of cement mortar
1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per
sqm including cost of backing coat pointing in white cement and matching
pigment, staging if required etc. complete all as per specifications and drawings
and as directed by Engineer In Charge.
Ref Drg no. I - 606


46 Providing & Fixing in position up to 150mm wide and 19mm thick machine cut Rmt. 35.00
Telephone Black Flamed Granite as per the approved sample for ledges/
Threshold etc. as per the drawing laid to the required level & line including
cutting of stone to the required size & shape, edge polishing / chamferred edges,
surface preparation including cement backing with 1:1 cement grout, filling &
finishing the joints with cement & approved colour pigments, cutting, mirror
polishing to moulding & exposed edges, curing, cleaning etc complete as per the
instructions of the EIC. (Mode of measurements : Running length of ledge/
treshhold shall be measured for payment)
Refer Drw. No. I-210, I-211, I-213, I-800, I-801, I-820, I-830
47 Providing & Fixing in position 150mm wide 19mm thick machine cut, Second Rmt. 65.00
quality marble as per the approved sample for Door/ window sils, jambs etc.
as per the drawing laid to the required level & line including cutting of stone to the
required size & shape, edge polishing / chamferred edges, surface preparation
including cement backing with 1:1 cement grout, filling & finishing the joints with
cement & approved colour pigments, cutting, mirror polishing to moulding &
exposed edges, curing, cleaning etc complete as per the instructions of the EIC.
(Mode of measurements : Running length of individual marble patti shall
Refer Drw. No I-210, I-211, I-213, I-800, I-801, I-820, I-830
48 Providing & Fixing in position 19mm thick machine cut,Telephone Black Flamed 0.00
Granite as per the approved sample for Door/ window cills, jambs or any
other specified in the drawing etc. as per the drawing laid to the required level
& line including cutting of stone to the required size & shape, edge polishing /
chamfered edges, surface preparation including cement backing with 1:1 cement
grout, filling & finishing the joints with cement & approved colour pigments,
cutting, mirror polishing, curing, cleaning etc complete as per the instructions of
the EIC. (Mode of measurements : Running length of individual marble
patti shall be measured for payment).
Refer Drw. No.I-210, I-211, I-213, I-800, I-801, I-820, I-830
48.1 Up to 75mm wide patti. Rmt. 130.00

48.2 Above 75mm and up to 150mm wide patti Rmt. 10.00


49 Providing & Fixing in position 19mm thick machine cut, Telephone Black 0.00
prepolished granite as per the approved sample for door thresholds, window
cills, jambs or any other specified in the drawing etc. as per the drawing laid
to the required level & line including cutting of stone to the required size & shape,
edge polishing / chamfered edges, surface preparation including cement backing
with 1:1 cement grout, filling & finishing the joints with cement & approved colour
pigments, cutting, mirror polishing to moulding & exposed edges, curing, cleaning
etc complete as per the instructions of the EIC. (Mode of measurements :
Running length of individual Granite patti shall be measured for payment)
Refer Drw. No I-210, I-211, I-213, I-800, I-801, I-820, I-830

50 Providing & constructing 600mm wide wash basin counters with 100mm deep Rmt. 3.00
facia as per the architectural drawing using min. 19mm thk pre polished
Telephone Black granite slab as per approved sample including, bed mortar in
CM 1:4, providing & fixing 19mm thk second quality marble base, including filling
& finishing the joints with cement & colour pigments, cutting opening in granite &
marble to accommodate wash basin, fixing of wash basin, half / full round
moulding, moulding polishing, edge polishing, curing, cleaning, etc complete at all
levels and as per the instructions of the EIC. Rate to include entire design as per
the detail in addition to the vertical and horizontal support to be polished on the
exposed side. (Mode of measurements : Running length of counter shall be
Refer Drw. No. I-210, I-211, I-213, I-602A, I-602B, I-603A, I-603B, I-703,
I-830


51 Providing & constructing Prepolished Telephone Black Granite Pantry Rmt. 10.00
Platform / Registration Counter comprising of 600mm wide counter top made
out of 16-18mm thk machine cut prepolished granite slab as per approved
sample with 75mm high granite fascia & end vertical granite piece (both side
polished) etc. as per the architectural drawing including, chasing in wall,
providing & fixing 30mm thk. polished cuddapah second quality marble slab base
supported on vertical cadappa second quality marble supports, p/l bed mortar in
CM 1:4, cutting of stone to the required size & shape, filling & finishing the joints
with cement & colour pigments, making opening in granite & cudappa to
accommodate the 600mm sink, Providing & fixing of sink, half / full round
moulding, Granite moulding/ edge mirror polishing, curing, cleaning, etc complete
as per the instructions of the EIC (Mode of measurements : Running length
of -platform shall be measured for payment)
Refer Drw. No. I-210, I-211, I-213, I-606, I-707, I-830
52 Providing & laying IPS flooring (as base for Vinyle flooring) or any other location 0.00
as specified by EIC of various thickness with cement concrete nominal mix of
proportion 1:2:4 (cement : Sand : Aggregate) in correct level / slope at all levels as
per architectural drawings including mixing of concrete in mixer, lifting, shifting to
the work location, compacting / vibrating, finishing smooth to the satisfaction of
the EIC, curing, and cleaning the surface etc. complete. (Mode of
measurements :Plan area of Flooring shall be measured for payment)
Refer Drw. No. I-210, I-211, I-213, I-709, I-830
52.1 Average up to 25mm thick IPS. Sqm. 5.00

52.2 Average above 25mm and up to 50mm thick IPS. Sqm. 5.00
52.3 Average above 50mm and up to 100mm thick IPS. Sqm. 395.00
53 Providing & fixing 3mm thick Vinyl sheet (Armstrong-VARIT PUR 531-052 / Sqm. 395.00
Responsive - SP-10) for flooring confirming to IS 3462-1986 of Armstrong/
Atco make & colour/pattern for Auditorium flooring and any other specified area in
correct level / slope at all levels as per architectural drawings and manufacturer's
specifications & instructions. Vinyl shall be fixed with approved adhesive properly,
avoid bubbles in flooring including cleaning the surface, pressing the vinyl by
appropriate roller properly, cutting and filling/ welding the joints by approved and
matching colour welding rod properly etc. completed as per the instructions of the
EIC. Joints shall be finished properly so that area shall look Continuously and joint
less. (Mode of measurements : Area of Vinyl flooring shall be measured
for payment) Refr Drw. No. I-210, I-211, I-213, I-709, I-830


54 Providing & Fixing in position 19mm thick machine cut, machine polished 0.00
Anglomerated marble as per the approved sample for Door/ window cills,
jambs or any other specified in the drawing etc. as per the drawing laid to the
required level & line including cutting of stone to the required size & shape, edge
polishing / chamfered edges, surface preparation including cement backing with
1:1 cement grout, filling & finishing the joints with cement & approved colour
pigments, cutting, mirror polishing, curing, cleaning etc complete as per the
instructions of the EIC. (Mode of measurements : Running length of
individual marble patti shall be measured for payment).

55 Providing & constructing Prepolished 19mm thick Telephone Black Granite Rmt. 15.00
Sitting (350 x 450 mm high in size) in Prefunction area comprising of
following. Providing and constructing 230mm thick brick work in 450mm height
finish the brick work with 12mm thick single sandfaced plaster in 1:4. P/f 350 mm
wide granite top fixed with backing cement paste properly. Also fixing 30mm wide
nosing with araldite all round with 6mm patta moulding at top and bottam as per
architectural drawing and instructions including necessary excavation, 230mm thk
soling, 100 mm thick pcc in M100, cutting of stone to the required size & shape,
filling & finishing the joints with cement & colour pigments, Granite moulding/
edge mirror polishing, curing, cleaning, etc complete as per the instructions of the
EIC (Mode of measurements : Running length of counter shall be
TOTAL OF FLOORING, SKIRTING & DADO WORK 0.00
G PAINTING WORK 0.00


56 Providing & applying following types of acrylic based emulsion paint / Luxury 0.00
emulsion paint ( Conforming IS 5411-1974) of make JOTUN for internal
gypsum / POP surface to be applied as per manufacturer's instructions &
methodology as directed by Architect including preparing the surface, p/a one
coat of water base PVA primer (copolymer based alkali resistant primer with
fungicide) of Jotun make and two coat of water base acrylic putty of Jotun make,
sanding, light sanding, scaffolding, work platform, painting equipment / apparatus
etc. required to complete interior grade finish with 3 coats of approved shade
colour etc. complete as directed by the EIC at all heights & levels. (Mode of
measurement- Only painting area shall be measured for payment)
Refer Drw. No. I-210, I-211, I-213, I-300A, I-300B, I-602A, I-602B, I-603A,
I-603B, I-606, I-607A, I-607B, A-501, A-502, A-800 I-830)
56.1 Fenomastic gold 007 to wall in green room and projector room Sqm. 150.00
56.2 Fenomastic matt 003 to ceiling green room and projector room Sqm. 70.00
56.3 Do as per item no.56.2 but spray painting (217-4000 B-G) for ceiling straw Sqm. 210.00
boards/ AC ducts and any other location as directed by EIC/ Architects.
57 Providing & applying 1st quality synthetic enamel paint ( Conforming IS 2932- Sqm. 200.00
1994) (for service areas) of approved make & shade in 3 coats over a coat of
approved quality primer to the wooden surface / MS railings & grills including
providing, erecting & dismantling scaffolding, preparation of surface, appying hard
putty, sanding, etc. complete as diected by the EIC at all lheights & levels. (Mode
of measurement- Only painting area shall be measured for payment)
Refer Drw. No. I-210, I-211, I-213, I-605A, A-201, A-501, A-502, A-503, A-
800, I-830
58 Providing & applying 1st quality Water cut enamal paint ( Conforming IS 2932- Sqm. 5.00
1994) of approved make & shade for wooden surface / MS railings & grills to be
applied as per manufacturer's instructions & methodology as directed by Architect
including preparing the surface, p/a one coat of water base metalic primer of
Estee or equivalent make and two coat of water base acrylic putty, sanding with
water, light sanding with water, scaffolding, work platform, painting equipment /
apparatus, dismantling scaffolding and cleaning etc. required to complete interior
grade finish with 3 coats of approved shade colour etc. complete as directed by
the EIC at all heights & levels. (Mode of measurement- Only painting area
shall be measured for payment)
Refer Drw. No. I-210, I-211, I-213, I-605A, A-201, A-501, A-502, A-503, A-
800, I-830


59 Providing & applying following types of Decorative paint / Texture paint of 0.00
make OIKOS/Jotun or equivalent make for internal gypsum / POP surface to be
applied as per manufacturer's instructions & methodology as directed by Architect
including preparing the surface, p/a one coat of water base PVA primer
(copolymer based alkali resistant primer with fungicide) of OIKOS / Jotun and two
coat of water base acrylic putty of OIKOS / Jotun , sanding, light sanding,
scaffolding, work platform, painting equipment / apparatus etc. required to
complete interior grade finish with 3 coats of approved shade colour etc. complete
as directed by the EIC at all heights & levels (Mode of measurement- Only
painting area shall be measured for payment)
Refer Drw. No. I-210, I-211, I-213, I-830, I-600A, I-600B, I-601, I-602A, I-
602B, I-603A, I-603B, I-604A, I-604B, I-604C, I-604D, I-604E, I-605A, I-
605B, I-606, I-607A, I-607B, I-701, I-703, I-705A, I-705B, I-706
59.1 For Auditorium wall paneling (Make - OIKOS- Antique effect-811/ Asian paints- Sqm. 165.00
Royale play Dune Silver Streak M609) Range - Special Products)
59.2 For Green room wall paneling (Make - OIKOS-Antique effect-812 / Asian paints- Sqm. 10.00
Royale play Dune Silver Streak M609 Dark ) Range - Special Products
59.3 For Prefunction and Post Function area.External texture paint (Make - Jotun- Sqm. 75.00
Texotile- B-G-213-4502B / Asian Paints - Pebble Tex Head cut- steel 6142)
Range - Special Products
59.4 For Prefunction and Post Function area.External texture paint (Make - Jotun- Sqm. 135.00
Texotile- B-G-213- 7502B / Asian Paints - Pebble Tex Head cut- Charcoal Shadow
8286) Range - Special Products
59.5 For Prefunction area (Make- Asian Silver metalic paint-Shade code 135- 30 % Sqm. 15.00
dark) Range - Special Products .
59.6 For Prefunction and Post Function area External paint (Make - Sherwin Williams- Sqm. 40.00
Beige Assorted Paino / Aisan Paints - Swirl Tex with top coat of Apex)


60 Providing and applying Two coats of acrylic based paint Jotashield matt- Jotamatt Sqm. 115.00
white of Jotun or equivalent make, color & shade to the external surface over
a coat of primer of Jotun make in Pre-function area including scaffolding, labour,
and material and preparing surface. The surface shall be thoroughly cleaned off
all mortar dropping, dirt dust, algae, fungus or moth grease and other foreign
matter of brushing and washing ,pitting in plaster shall make good surface
imperfections such as cracks , holes etc. should be repaired using white cement.
Approval of the prepraed surface to be obtained before commencement of
painting work. Paint shall be applied with a brush on the cleaned and smooth
surface .Horizontal strokes shall be given , first and vertical strokes shall be
immediately afterwards. This entire operation will constitute one coat .The surface
shall be finished smooth uniformly etc. complete. as directed by the Project In
charge at all heights & levels.
Refer Drw. No. I-210, I-211, I-213, I-830, I-300A, I-600B, I-601, I-700
61 Providing & applying Natural / French polish ( Conforming IS 348-1968) in 3 or Sqm. 10.00
more coats of approved shade to the wooden / Plywood / veneer surface,
mouldings pattas, grooves etc. including surface preparation, applying filler /
hardener / putty, sanding, cleaning of furniture after completion of job etc.
complete as directed by the EIC. (Mode of measurement- Only polishing
area shall be measured for payment)
Refer Drw. No. I-210, I-211, I-213, I-830, I-602A , I-602B, I-603A, I-603B,
I-606, I-703, I-707
62 Providing and applying Melamine polish for exposed wooden surfaces Sqm. 65.00
wherever directed by the architects. including surface preparation, applying filler /
hardener / putty, sanding, cleaning of furniture, required smooth finishing after
completion of job etc. complete as directed by the EIC. (Mode of measurement-
Only polishing area shall be measured for payment)
Refer Drw. No. I-210, I-211, I-213, I-830, I-602A , I-602B, I-603A, I-603B,
I-606, I-703, I-707
TOTAL OF PAINTING WORK 0.00
H DOOR WORKS 0.00

All the hardware fitings and Fixtures shall be Ozone or any other equivalent 0.00
approved make


63 Providing & fixing 45mm thick(excluding finishes) single leaf commercial each 1.00
Flush door shutter (D1) (900 X 2075mm in size) for Green room Gents Main
door of approved make & type comprising of phenol bonded solid core made up
of kiln seasoned battens, crossbands & face veneers all from selected strong &
durable hardwoods bonded together under heat & pressure using a BWP type
Phenol Formaldehyde synthetic resin adhesive. The flush door shall conform to
IS2202, 1991. Door shall be fire rated for 30 minutes. The flush door shall be
finished with 1 mm thk laminate on both sides (Laminate to be approved by
architect before commencement of work) including providing & fixing 12 mm thk
TW lipping all around ffinish with approved melemine poilish matching to the
laminate . Rate also included providing and fixing teak wood door frame of size
150mm x 75mm finish with approved water cut enamel paint , p/f teak wood
architrave 42 x 10mm in size finish with approved watercut enamel paint,
including providing all necessary consumables viz. adhesive, necessary
hardware, necessary beads moulding, lipping,fastenings, 8 Nos MS hold fast, p/f
fittings and fixtures of Ozone make & cleaning etc. completed at all floors &
heights as per architectural drawings and instructions.
Fittings & Fixtures per leaf

Heavy Duty satin finish butt SS Hinges (100mm x 75mm x 3mm in size) -4 nos.
SS finished leaver handle with Doble cylindrical lock- 1 no.

Concealed door closer- 1 No.
Key hole-


Flush door shutter (D2) (900 X 2075mm in size) for Green room Ladies Main
door of approved make & type comprising of phenol bonded solid core made up
of kiln seasoned battens, crossbands & face veneers all from selected strong &
IS2202, 1991.Door shall be fire rated for 30 minutes. The flush door shall be
finished with 1 mm thk laminate on both sides (Laminate to be approved by
architect before commencement of work) including providing & fixing 12 mm thk
TW lipping all around finish with approved melemine poilish matching to the
laminate . Rate also included providing and fixing teak wood door frame of size
150mm x 75mm finish with approved water cut enamel paint, p/f teak wood
architrave 42 x 10mm in size finish with approved watercut enamel paint,
including providing all necessary consumables viz. adhesive, necessary
hardware, necessary beads moulding, lipping,fastenings, 8 Nos MS hold fast,
p/f fittings and fixtures of Ozone make & cleaning etc. completed at all floors &
Fittings & Fixtures per leaf

Heavy Duty satin finish butt SS Hinges (100mm x 75mm x 3mm in size) -4 nos.
SS finished leaver handle with Doble cylindrical lock- 1 no.

Concealed door closer- 1 No.
Key hole-
65 Providing & exchanging 1mm thick laminate (Laminate to be approved by each 1.00
architect before commencement of work) of existing door (D3) for Green
room Gents internal door. including removing old laminate providing all necessary
consumables viz. adhesive, necessary hardware, necessary beads moulding,
lipping,fastenings, cleaning etc. completed at all floors & heights as per
architectural drawings and instructions.
66 Providing & exchanging 1mm thick laminate (Laminate to be approved by each 1.00
architect before commencement of work) of existing door (D4) for Green
room Ladies internal door. including removing old laminate providing all necessary
lipping,fastenings, cleaning etc. completed at all floors & heights as per


67 Providing & fixing in positions double shutter Glass door inclusive of side fixed each 1.00
glazing (D5) (2100 x 2100mm in size) for main enterance Door in prefunction
area with using 12 mm thick fixed Toughened Plain glass of Modi make or any
other approved equivalent make and quality,having top & bottom frame in tw of
approx size 200mm x 50mm thk finished in dark melamine polish, hung with
heavy duty floor spring of Ozone as per architectural drawings and instructions
including cutting, edge polishing, buffing necessary hardware, etc. completed.at
all floors & heights as per architectural drawings and instructions.
Fittings & Fixtures (per leaf) 0.00

heavy duty floor spring - 1no. 0.00
26mm dia & 600mm long handle 'D' type in ss finish as approved. 0.00
SS Patch fittings lock 0.00
150mm Concealed SS tower bolt 0.00
Refer Drw. No. I-210, I-211, I-213, I-800, I-801, I-830 0.00
68 Providing & fixing in positions double shutter Glass door inclusive of side fixed each 1.00
glazing (D6) (2100 x 2100mm in size) for main enterance Door in prefunction
area with using 12 mm thick fixed Toughened Plain glass of Modi make or any
other approved equivalent make and quality,having top & bottom frame in tw of
approx size 200mm x 50mm thk finished in dark melamine polish, hung with
heavy duty floor spring of Ozone as per architectural drawings and instructions
including cutting, edge polishing, buffing necessary hardware, etc. completed.at
all floors & heights as per architectural drawings and instructions.

heavy duty floor spring - 1no. 0.00
SS Patch fittings lock 0.00
150mm Concealed SS tower bolt 0.00


69 Providing & fixing 45mm thick(excluding finishes) having fire rating of 30 each 1.00
mins, Double leaf commercial Flush door shutter (D7) (2100 X 2400mm in
size) for Main house entry door of approved make & type comprising of phenol
bonded solid core made up of kiln seasoned battens, crossbands & face veneers
all from selected strong & durable hardwoods bonded together under heat &
pressure using a BWP type Phenol Formaldehyde synthetic resin adhesive. The
flush door shall conform to IS2202, 1991. The flush door shall be finished with 1
mm thk laminate on both sides (Laminate to be approved by architect before
commencement of work) including providing & fixing 12 mm thk TW lipping all
around finish with approved melemine poilish matching to the laminate . Rate also
included providing and fixing teak wood door frame of size 475mm x 95mm finish
with approved water cut enamel paint, including providing all necessary
lipping,fastenings, 8 Nos MS hold fast, p/f fittings and fixtures of Ozone make &
cleaning etc. completed at all floors & heights as per architectural drawings and
instructions.
Fittings & Fixtures per leaf 0.00

Heavy Duty satin finish butt SS Hinges (100mm x 75mm x 3mm in size) -4 nos. 0.00
Double cylindrical lock- 1 no. 0.00

Concealed door closer- 1 No. 0.00
Door drop seal 0.00
Concealed door stopper 0.00
Door seal- 0.00


70 Providing & fixing 45mm thick(excluding finishes) having fire rating of 30 each 1.00
mins, Double leaf commercial Flush door shutter (D8) (2100 X 2400mm in
size) for Main house entry door of approved make & type comprising of phenol
bonded solid core made up of kiln seasoned battens, crossbands & face veneers
all from selected strong & durable hardwoods bonded together under heat &
pressure using a BWP type Phenol Formaldehyde synthetic resin adhesive. The
flush door shall conform to IS2202, 1991. The flush door shall be finished with 1
mm thk laminate on both sides (Laminate to be approved by architect before
with approved water cut enamel paint, including providing all necessary
instructions.

Doble cylindrical lock- 1 no. 0.00

Door drop seal 0.00
Concealed door stopper- 0.00
Door seal- 0.00


Flush door shutter (D9) (800 X 2100mm in size) for Stage door of approved
make & type comprising of phenol bonded solid core made up of kiln seasoned
battens, crossbands & face veneers all from selected strong & durable hardwoods
bonded together under heat & pressure using a BWP type Phenol Formaldehyde
synthetic resin adhesive. The flush door shall conform to IS2202, 1991.Door
shall be fire rated for 30 minutes. The flush door shall be finished with
approved water cut enamel paint (Asian paints- Gloos Enamel Paint or Satin
Enamel Paint Matching the Laminate) from outside and finished with 1 mm thk
laminate (Laminate to be approved by architect before commencement of work)
from inside, including providing & fixing 12 mm thk TW lipping all around ffinish
with approved water cut enamel paint. Rate also included providing and fixing
teak wood door frame of size 110mm x 50mm finish with approved water cut
enamel paint, p/f teak wood architrave 42 x 10mm in size finish with approved
watercut enamel paint, including providing all necessary consumables viz.
adhesive, necessary hardware, necessary beads moulding, lipping,fastenings, 8
Nos MS hold fast, p/f fittings and fixtures of Ozone make & cleaning etc.
completed at all floors & heights as per architectural drawings and instructions.

SS finished leaver handle with Doble cylindrical lock- 1 no. 0.00

Door drop seal-
Key hole- 0.00


Flush door shutter (D10) (800 X 2100mm in size) for Stage door of approved
synthetic resin adhesive. The flush door shall conform to IS2202, 1991.Door
shall be fire rated for 30 minutes. The flush door shall be finished with
approved water cut enamel paint (Asian paints- Gloos Enamel Paint or Satin
Enamel Paint Matching the Laminate) from outside and (Laminate to be
approved by architect before commencement of work), including providing & fixing
12 mm thk TW lipping all around ffinish with approved water cut enamel paint .
Rate also included providing and fixing teak wood door frame of size 110mm x
50mm finish with approved water cut enamel paint, p/f teak wood architrave 42 x
10mm in size finish with approved watercut enamel paint, including providing all
necessary consumables viz. adhesive, necessary hardware, necessary beads
moulding, lipping,fastenings, 8 Nos MS hold fast, p/f fittings and fixtures of Ozone
make & cleaning etc. completed at all floors & heights as per architectural
drawings and instructions.


Door drop seal-
Key hole- 0.00


73 Providing & fixing 45mm thick (excluding finishes) single leaf marine Flush each 1.00
door shutter (D11) (1000 X 2100mm in size) for Fire exit door of approved
synthetic resin adhesive. The flush door shall conform to IS2202, 1991. Door
shall be fire rated for 30 minutes. The flush door shall be finished with 1 mm
thk laminate on both sides (Laminate to be approved by architect before
with approved water cut enamel paint, p/f teak wood architrave 42 x 10mm in size
finish with approved watercut enamel paint, including providing all necessary
instructions.

Panic bar -. 0.00

Door drop seal 0.00
Concealed door closer. 0.00


74 Providing & fixing 45mm thick (excluding finishes) single leaf marine Flush each 1.00
door shutter (D12) (1000 X 2100 mm in size) for Fire exit door of approved
synthetic resin adhesive. The flush door shall conform to IS2202, 1991. Door
shall be fire rated for 30 minutes. The flush door shall be finished with 1 mm
thk laminate on both sides (Laminate to be approved by architect before
with approved water cut enamel paint, p/f teak wood architrave 42 x 10mm in size
finish with approved watercut enamel paint, including providing all necessary
instructions.

Panic bar -. 0.00

Door drop seal 0.00
Concealed door closer. 0.00
75 Providing & fixing 45mm thick(excluding finishes) Double leaf commercial each 1.00
marine Flush door shutter (D13) (1520 X 2100mm in size) for Post function
area door of approved make & type comprising of phenol bonded solid core made
up of kiln seasoned battens, crossbands & face veneers all from selected strong &
IS2202, 1991. The flush door shall be finished with 1 mm thk laminate on both
sides (Laminate to be approved by architect before commencement of work),
including providing & fixing 12 mm thk TW lipping all around finish with approved
melemine poilish matching to the laminate . Rate also included providing and
fixing teak wood door frame of size 475mm x 75mm finish with approved water
cut enamel paint, including providing all necessary consumables viz. adhesive,
necessary hardware, necessary beads moulding, lipping,fastenings, 8 Nos MS
hold fast, p/f fittings and fixtures of Ozone make & cleaning etc. completed at all
floors & heights as per architectural drawings and instructions.



Door drop seal 0.00
Concealed stopper 0.00
Door seal- 0.00
76 Providing & fixing 45mm thick(excluding finishes) Double leaf marine Flush each 1.00
door shutter (D14) (1520 X 2100mm in size) for Post function area door of
approved make & type comprising of phenol bonded solid core made up of kiln
seasoned battens, crossbands & face veneers all from selected strong & durable
hardwoods bonded together under heat & pressure using a BWP type Phenol
Formaldehyde synthetic resin adhesive. The flush door shall conform to IS2202,
1991. The flush door shall be finished with 1 mm thk laminate on both sides
(Laminate to be approved by architect before commencement of work) including
providing & fixing 12 mm thk TW lipping all around finish with approved melemine
poilish matching to the laminate . Rate also included providing and fixing teak
wood door frame of size 475mm x 75mm finish with approved water cut enamel
paint, including providing all necessary consumables viz. adhesive, necessary
hardware, necessary beads moulding, lipping,fastenings, 8 Nos MS hold fast,
p/f fittings and fixtures of Ozone make & cleaning etc. completed at all floors &

per shutter
Door drop seal 0.00
Concealed stopper 0.00
Door seal- 0.00


77 Providing & fixing 45mm thick(excluding finishes) single leaf marine Flush each 1.00
door shutter (D15) (900 X 2100mm in size) for Projector room door of
approved make & type comprising of phenol bonded solid core made up of kiln
seasoned battens, crossbands & face veneers all from selected strong & durable
hardwoods bonded together under heat & pressure using a BWP type Phenol
Formaldehyde synthetic resin adhesive. The flush door shall conform to IS2202,
1991.Door shall be fire rated for 30 minutes. The flush door shall be finished
with 1 mm thk laminate on both sides (Laminate to be approved by architect
before commencement of work) including providing & fixing 12 mm thk TW lipping
all around ffinish with approved melemine poilish matching to the laminate. Rate
also included providing and fixing teak wood door frame of size 150mm x 75mm
finish with approved water cut enamel paint, p/f teak wood architrave 42 x 10mm
in size finish with approved watercut enamel paint, including providing all
moulding, lipping,fastenings, 8 Nos MS hold fast, p/f fittings and fixtures of Ozone
make & cleaning etc. completed at all floors & heights as per architectural
drawings and instructions.


Key hole- 0.00
78 Providing & exchanging 1mm thick (Laminate to be approved by architect each 1.00
before commencement of work) of existing door (D16) for pantry door.
including removing old laminate providing all necessary consumables viz.
adhesive, necessary hardware, necessary beads moulding, lipping,fastenings,
instructions.
TOTAL OF DOOR WORKS
I WOOD WORKS (PARTITION & PANELLING)


79 Providing & fixing 6mm thick Plain Mirror of modi or equivalent for Green Room Sqm. 10.00
as per approved shape, size and as per architectral rawing and instruction fixed
with 25mm dia SS Studs properly. Rate also included providing all necessary
consumables viz., necessary hardware etc. complete at all heights as per
Refer Drw. No. I-210, I-211, I-213, I-830, I-602A, I-602B, I-
603A, I-603B, I-703
80 Providing & fixing 6mm thick frosted glass of modi or equivalent for Green Sqm. 2.00
Room as per approved shape, size and as per architectral rawing and instruction
fixed with 25mm dia SS Studs properly. Rate also included providing all
necessary consumables viz., necessary hardware etc. complete at all heights as
per architectural drawings and instructions.
Refer Drw. No. I-210, I-211, I-213, I-830, I-602A, I-602B,
I-603A, I-603B, I-703
81 Providing & fixing in positions 12 mm thick commercial ply and 12 mm thick 0.00
calicium silicate board paneling as per architectural drawing and instructions.
The system shall be comprising following. Ply frame work -Providing, making
and fixing 18mm thick marine ply frame work as architectural drawing and
instruction at all shapes and sides.
Panelling- providing and fixing 12mm thick commercial ply fix on the frame and
finish the ply with 12mm thick calcium silicate board as per architectural drawing,
including cutting, necessary hardware, drilling, The work also includes vertical
drops, sides, curvature, cutting of ply/veneer & frame work and providing cutouts /
openings for switch boards, fd and cleaning etc. completed at all floors and
heights as specified and directed by Architects/ EIC.
Ref Drw. No. I-210, I-211, I-213, I-830, I-600A, I-600B, I-601, I-700, I-701,
I-706
(Front elevational area shall be measured for Billing)
81.1 Up to 50mm thick paneling- Sqm. 35.00

81.2 Above 50mm and up to 100mm thick paneling Sqm. 5.00
81.2a Above 50mm and up to 100mm thick paneling Sqm. 175.00


82 Providing & fixing in positions 12 mm thick commercial ply and fabric paneling 0.00
as architectural drawing and instructions. The system shall be comprising
following.
Aluminum frame work -Providing, making and fixing aluminum frame work
made out of 38x 50mm aluminum heavy box section @ 600mm c/c both ways
(spacing should no be exceed than 600mm depending on length and height).
Frame shall be supported with aluminum box section of 38x 50mm @ 600mm c/c
fix on wall with 40x40x3mm aluminum angle as per thickness of paneling.
Panelling- providing and fixing 12mm thick commercial ply frame made out of
150mm x 12mm @ 600mm c/c both ways.p/f 20mm thick basotect foam in the
frame as per drawing. And finish the paneling with approved fabric (Bharat
Furnishing -premium shade 24293- SR. No.- 6- 24292- SR. No.- 23-Munnar silk /
Decotex - VRN 817 Decotex - VRN 816). including cutting, necessary hardware,
drilling, Vinyl pvc gripper,. The work also includes vertical drops, curvature, coves,
cutting & frame work and providing cut out and necessary support for switch
boxes and lightfittings and cleaning etc. completed at all floors. Fabric should be
streched properly to avoid bubbles and loosness.
Refer Drw. No. I-210, I-211, I-213, I-830, I-604A, I-604B, I-604C, I-604D,
I-604E, I-705A, I-705B
82.1 Up to 100mm thick paneling Sqm. 2.00

83 Providing & fixing in positions 20 mm thick Basotect Foam and fabric paneling Sqm. 25.00
as per architectural drawing and instructions. The system shall be comprising
following.
Panelling- providing and fixing 20mm thick basotect foam including wire mesh
on the wall at given location as per drawing. And finish the paneling with
approved fabric (Surprise house warming- premium shade HW/FLTEX / Surprise
house warming- premium shade Shiro 32 N Blue) including cutting, necessary
hardware, drilling, Vinyl pvc gripper,. The work also includes vertical drops,
curvature, coves, cutting & frame work and providing cut out and necessary
support for switch boxes and lightfittings and cleaning etc. completed at all floors.
Fabric should be streched properly to avoid bubbles and loosness.
I-604E, I-705A, I-705B


84 Providing & fixing in positions 20 mm thick Straw board and fabric paneling as 0.00
per architectural drawing and instructions. The system shall be comprising
following.
made out of 50 x 50mm aluminum heavy box section @ 600mm c/c both ways
( spacing should no be exceed than 600mm depending on length and height).
Panelling- providing and fixing 20mm thick Straw board as per drawing. And
finish the straw board with approved fabric (Bharat Furnishing - Premium shade -
24293 - Sr. No. 6 Munar Silk / Decotex - VRN 817 Decotex - VRN 818). including
cutting, necessary hardware, drilling,The work also includes vertical drops,
curvature, coves, cutting & frame work and providing cut out and necessary
support for switch boxes and lightfittings and cleaning etc. completed at all floors.
Fabric should be streched properly to avoid bubbles and loosness.

85 Providing & fixing in positions 20 mm thick Straw board and fabric paneling as 0.00
per architectural drawing and instructions. The system shall be comprising
following.
made out of 50 x 50mm aluminum heavy box section @ 600mm c/c both ways
( spacing should no be exceed than 600mm depending on length and height).
Panelling- providing and fixing 20mm thick Straw board as per drawing. And
finish the straw board with approved fabric (Bharat Furnishing -premium shade
24293- SR. No.- 6- Munnar silk / Decotex - VRN 817 Decotex - VRN 818).
including cutting, necessary hardware, drilling,The work also includes vertical
drops, curvature, coves, cutting & frame work and providing cut out and
necessary support for switch boxes and lightfittings and cleaning etc. completed
at all floors. Fabric should be streched properly to avoid bubbles and loosness.
I-604E, I-705A, I-705B


86 Providing & fixing in positions MDF board paneling as per architectural drawing 0.00
and instructions. The system shall be comprising following.
Aluminum frame work -Providing,
making and fixing aluminum frame work made out of 50 x 50mm aluminum heavy
box section @ 600mm c/c both ways ( spacing should no be exceed than 600mm
depending on length and height). fixed directly on wall as per drawing and
thickness of paneling.
Panelling- providing and fixing two nos. 6mm thick sandwitched exterior grade
MDF board fixed on frame as per drawing including cutting, necessary hardware,
drilling,The work also includes vertical drops, curvature, coves, cutting & frame
work and providing cut out and necessary support for switch boxes and
lightfittings and cleaning etc. completed at all floors.
I-604E, I-705A, I-705B

86.1a Up to 100mm thick paneling Sqm. 25.00
87 Providing and fixing 20mm thick Commercial ply storage shutters of approved Sqm. 10.00
make as per architectural drawing and instructions Frame out of 40MM X
25MM ,fixed to the kadappa or wall surface with as per detailed drawing. Shutter
panels finished with 1mm thick laminate (Laminate to be approved by architect
before commencement of work) on out side and french polish at inside and
hinged to framework with 2nos 100mm s.s hinges including providing all
moulding, lipping, fastenings, fittings and finish the wooden frame french polish
etc. complete at all floors & heights as per architectural drawings and instructions.
(Mode of measurement- Only one side shutter area shall be measured for
payment)
Refer Drw. No. I-210, I-211, I-213, I-830, I-602A, I-602B, I-603A, I-603B,
I-606, I-703, I-707


88 Providing, making and fixing 75mm thick full height Stage back Ply partition as Sqm. 65.00
per architectural drawing and instructions . The system shall be comprising of
following.Frame work- Providing. making and fixing aluminum frame work made
out of 38mm x 50mm aluminum box section @ 600 mm c/c in both ways fix
properly as per drawing.Ply - Providing and fixing 12 mm thick commercial ply
fixed on peripheri of the frame as per architectural drawings and instructions
including cutting, necessary hardware, drilling, cut out and necessary support for
switch boxes and lightfittings and finish. All connections in framework shall be with
GI screws of approved quality.Ply with tapered edges to be screwed to the
framework with 25mm long GI screws at 230 mm c/c. Screw fixing shall be done
mechanically. 20 mm thick Basotect foam shall be sandwithched in ply and frame
properly. and finish the panelling with aproved colour fabric (Bharat Furnishing -
Premium shade - 24293 - Sr. No. 6 Munar Silk / Decotex - VRN 817 Decotex -
VRN 818), fabric shall be stiched properly to avoid bubbles and looseness and
cleaning etc. completed at all floors and heights as specified and directed by
Architects/ EIC.
I-604E, I-705A, I-705B
89 Providing and fixing 300mm wide and 25mm thick commercial ply shelves for Rmt. 5.00
Changing Room fixed in partitions at given loction properly as per architectural
drawing and instructions and finish the shelves with 1mm thick approved make
and colour laminate(Laminate to be approved by architect before commencement
of work) including providing all necessary consumables viz. adhesive, necessary
hardware, necessary beads moulding, lipping, fastenings etc. complete at all
floors & heights as specified and as directed by EIC. (Mode of measurement-
Only running length of shelves shall be measured for payment)
I-703
90 Providing & fixing 12mm thick & 75mm high approved quality Wooden skirting Rmt. 15.00
finished with approved melamine polish as per the pattern given to correct line,
level & plumb including chasing of wall wherever required, surface preparation,
joints should be proper, cutting, mitring at edges, screwing, necessary hardware,
lipping, commercial ply backing as per site condition, adhesives, cleaning . etc
complete as per the Architectural drawings & instructions. (Mode of
measurement- running length of skirting shall be measured for payment)
I-604E, I-705A, I-705B


91 Providing & fixing 2000mm x 795mm x 750mm height Unit for music each 1.00
instruments (Audio Mixer) in commercial ply as per architectural Drawing and
instructions comprise with following.- P/f two nos 19mm thick sandwitched ply for
legdge/top with drawers made out of 12mm thick commercial ply as per
architeural drawings and finish the unit with approved laminate (Laminate to be
approved by architect before commencement of work) at visible side.Back/ hidden
portion of ply & drawer inside shall be finish with french polish. providing all
moulding, lipping, fastenings, fittings, SS Chanels and cleaning etc. complete at
all floors & heights etc. completed as directed and as specified by EIC.
Refer Drw. No. I-210, I-211, I-213, I-830, I-607A, I-607B
92 Providing, making and errecting 500 mm wide and 750mm high Green room Rmt. 10.00
Dressing counter with wash basin made out of 19mm commercial ply as per
architectural drawing and instructions. Including 12mm thick marine ply facia,
drawers, p/f approved washbasin, providing all necessary consumables viz.
adhesive, necessary hardware, necessary beads moulding, lipping, fastenings,
fittings and finish the ply with approve laminate (Laminate to be approved by
architect before commencement of work) at visible side and french polish at
drawer inner side and whereever is required and cleaning etc. complete as
directed and as specified by EIC.
I-703
93 Providing & fixing 38 mm thick Glass Shutter (1350 X 950) for TV in each 1.00
Postfunction area comprising with 12mm thick Toghened clear glass fixed in 50 x
38mm teak wood frame finished with approved water cut enamel paint as per
architectural drawings and instructions including providing & fixing 12 mm thk TW
lipping all around finished with approved water cut enamel paint. Rate also
included providing and fixing teak wood shutter of size 50 x 38mme of size finish
with approved water cut enamel paint including providing all necessary
lipping,fastenings, L & Key locking system & cleaning etc. completed at all floors
& heights as per architectural drawings and instructions.
I-706


94 Providing, making and errecting 325mm high (height from finish top of existing Rmt. 12.00
stage) Proscenium as per architectural drawing and instructions . The system
shall be comprising of following .Frame work- Providing. making and fixing teak
wood frame work made out of 38mm x 38mm @ 600 mm c/c in both ways fix
properly to the existing stage from bottam of the stage as per drawing. Top portion
of vertical members shall be curve/ bend as per drawing. Ply - Providing and
fixing 8 mm thick flexi commercial ply fixed on peripheri of the frame including
boxing for conduting as per architectural drawings and instructions including
cutting, necessary hardware, drilling, cut out and necessary support for switch
boxes and lightfittings and finish the Ply with 1mm thick approved laminate
(Laminate to be approved by architect before commencement of work) at visible
side. All connections in framework shall be with GI screws of approved quality and
cleaning etc. completed at all floors and heights as specified and directed by
Architects/ EIC.
I-604E, I-705A, I-705B, I-708
95 Providing & fixing aluminium louvered grill for return air duct with approved colour Sqm. 20.00
power coated matching to the wall texture paint and 50 mm X 65 mm aluminium
box frame as per architectural detailed drawing including louvers, brass fixtures,
fastenings & fittings, necessary back packing, cutting, griding, drilling and
cleaning etc. complete. as specified and as directed by EIC / Architect.
I-604E, I-705A, I-705B
96 Providing and doing laminated wooden hardwood flooring of approved make and Sqm. 10.00
pattern and as per architectural drawing and instructions. The system shall be
comprise with following.
Wooden Flooring- Providing and fixing 150mm to 200mm and 19mm thick
interlocking wooden planks matching to the existing wooden flooring for stage
fixed on existing base properly as per architectural drwaing and instructions.
including necessary hardware, lipping, moulding, approved quality foam below the
wooden strips, cutting, drilling, finish the strips with approved melamine polish
matching to the existing wooden flooring and cleaning etc. completed as
directed and specified by EIC.
TOTAL OF WOOD WORKS (PARTITION & PANELLING) 0.00


J ALUMINUM WINDOW WORK
Note: -
i) The contractor shall submit 6 copies of shop drawings for each windows,
ventilators showing dimension details of construction etc. for approval of the
Engineer - in - charge. And according to the approved shop drawing a sample of
each of windows with all fittings and fixtures with locking arrangement including
glass panes etc. complete as per schedule of quantities, specifications and
drawings, shop drawing should be submitted for preliminary inspection for
approval. After preliminary inspection , the sample should be fixed at site to
ascertain its performance. Large scale manufacturing should be taken up only
after rectification of defects in samples as directed to the full satisfaction of the
department and after obtaining formal approval.
ii) All doors, windows, ventilators section shall be anodized extruded section of
M/s Jindal / M/s Indal or or any other makes specified in the list of approved
makes.
iii) All fittings / fixtures shall be of approved make / quality and as approved
by Architect.
iv) All dimensions mentioned in the drawing are approximate. Necessary

allowance for fixing over rough ground, and also necessary allowances for fixing
tolerances to be considered while manufacturing. While manufacturing, actual
site measurement shall be considered. Necessary planning for fixing the unit has
to be carried out by the contractor without any extra cost to the department.
However, rate quoted by the contractor shall hold good.
v) Payment shall be made per Kg basis.Aluminium sections such as shutter

frames, track window / door frame/beading channel for glass adjustable louvers
etc., shall only be measured linearly as per actual / finished cutting size nearest to
centimeter and multiplied with sectional weight of the individual section and the
total quantity of aluminum section will be arrived at for payment without any
allowance for wastage.
vi) All glass panes shall be of M/s Modi guard or or any other makes specified in
the list of approved makes. The glasses will be measured for payment
separately under relevant item.
vii) Glass panes shall be fixed with approved EPDM gasket ting, beading, to be
free from settling. Necessary polysulphide sealant to be provided against
seepage of rain water.
viii) All top hung/side hung shutters to be provided with approved quality of
stainless steel friction hinges.
ix) In case of damage of any existing work, the same has to be made
good/restored to original condition by the contractor at his own cost.

x) No separate payment shall be made for fittings such as locking arrangement,

hinges,frictionhinges, fittings and fixtures, gasket etc., Tenderer are required to
consider the cost of all fittings, fixtures, locking arrangement , handles, pegstays,
gaskets, screws, hinges etc., while quoting the rate for unit weight of aluminum
sections for window / door except for floor spring, hydraulic door closer and floor
lock will be paid separately under relevant item.
xi) Shall furnish guarantee of one year on a stamp paper for performance of
smooth operation and leakage.
97
Supply & fixing in position at all floors integrated Champagne color anodized matt
finished alluminium work work for door, window, ventilator, louver with extruded
builtup standard sections of Jindal / Aluminax or other approved make conforming
IS: 733 & IS: 1285 fixing with dash fastners of required size, including filling up the
gaps at junctions i.e. top, bottom & sides with required EPDM rubber / neoprene /
polysulphide sealant etc. Alluminium section shall be smooth, rust free, straight
and jointed mechanically wherever required, including cleat angle, alluminium
snap beading for glazing / paneling, stainless steel screws all complete.
The Aluminum consisting of followings described as 'under: - All fixing shall be

concealed pvt and/ 'anodized finished as per aluminum.
- EPDM / Neoprene purpose made beading shall be provided.
- Fixing shall be with GI screws.
- All sections shall be extruded.
- All beading shall be snap on type.
- Glazing beading shall be from inside only.
- Minimum thickness of glass shall be 6mm when not specified.
Sliding Windows.
- Anti-lifting device.
- Bottom rail shall be with self cleaning gutter section unless noted otherwise.
- Stainless steel ball bearings rollers.
- Concealed locking arrangement.
- In louvered windows, extruded sections only shall be used.
- All fitting and fixtures such as lever locks, handles, hinges, concealed tower
bolts, door closer etc. shall be suited to sections and be of approved make. They
shall be finished in matching coating or as approved.
- Supply and fixing of aluminum work shall be carried out from 'approved agency.
- Prior to start of work supplier shall submit detailed full scale
Shop drawings including plan, elevation and detail of fixing with structure for
approval of the EIC. Samples of each item on full
scale or smaller scale as directed by the EIC shall be submitted for approval.

- Work shall proceed only on approval of shop drawing, samples of each

extruded section, neoprene beading, gaskets, wool pile,
fittings and fixtures by the EIC in writing.
- Glazing shall be as noted for each unit in drawing.
97.1 For Fixed portion Kg 180.00
97.2 For shutters of doors, windows and ventilators including providing and fixing Kg 190.00
hinges / pivots and making provision for fixing of fittings wherever required
including the cost of PVC / neoprene gasket required (fittings shall be paid under
relevant item)
98 Providing and fixing glass panes in windows, doors, at all location and heights of
following thickness etc. all complete as per the directions of the EIC. (Mode of
measurement :-Dimension in length and width of exposed finished surface of
glass panel shall be measured sq.m nearest to 0.01 )
98.1 With 5.0 mm thick clear glass of approved make (fixed panel of windows) Sqm. 5.00
99 Vision Glass - 5mm Solar Low E Refl HS +12mm air Gap + 6mm clear float HS. Sqm. 20.00
The glass spectrophotometric properties shall be as follows : Glass appearance -
Light Grey , VLT- 46% , Solar factor - 0.45 max , shading coefficient - 0.51 max ,
U value - 2.8 W/m2K.
TOTAL OF ALUMINUM WINDOW WORK 0.00
K MISCELLANEOUS WORKS 0.00

100 Providing and fixing 75mm high Aluminum anodized skirting of Ensemble or any Rmt. 80.00
other equivalent approved make fixed to the wall with 5x25mm counter sunk
screws properly as per manufacturer’s specifications and instructions at given
location with architectural drawing including matching color inner/ outer connector,
end cap, rubber beading, commercila ply backing as per site condition, drilling,
cutting and cleaning etc. completed at floors & levels and as per the instructions
of the EIC. Joints shall be finished properly so that skirting shall look
Continuously and joint less. (Mode of measurement- Running length of the
skiring shall be measured for payment)
I-604E, I-705A, I-705B


101 Providing & fixing Trap door (hinged) of sizes given below with Red Meranti Sqm. 5.00
frame & suspenders (section 50mm x 50mm). Single shutter made out of 19mm
marine plywood & teak wood leaping hinged to the frame as shown in drawing
including P/f allen key lock, hinges, safety chain, necessary hardware, finished
with 1.0mm thick approved laminate on one side and synthetic enamel paint
( primer + 3 coats ) of approved make & shade on other side etc. complete as
instructed by the EIC. (Mode of measurements : Area of trap door opening
shall be measured for payment)
102 Providing and doing conbond chemical treatment to damaged RCC portion with Sqm. 10.00
rich concrete and using sunanda or equivalent bonding chemical as per
manufacturar's specifications & instructions.including removing damaged RCC
portion,form-work, compacting, finishing the exposed faces, curing & rate also
included P/d chemical treatment to Reainforcement etc. completed as specified
and as directed by EIC. (Mode of measurements : Only damaged area shall
Refer Drw. No. A-200, A-201, A-202, A-502, A-503, A-800
103 Providing, making and fixing Roller Blinds as per architectural drawing and 0.00
instructions made out of approved make and quality fabrics shall be made from
high quality texturised and spun yarn. It should has excellent textile appearance of
translucency, 100% polyster fabric, acrylic coating on both side of fabric, fabric
fixed to the proper location.including necessary hardware, drilling, cutting, powder
coate aluminum clips, rods and pulling rope. two blinds should be over lap to each
other by 150mm. etc. cpmpleted as required as specified by EIC. (Area of the
fabric shall be measured for billing)
I-604E, I-705A, I-705B
103.1 2) Providing and fixing Blackout Blinds ( Make- Galeecha -CB-04/ NL- 1511 W - Sqm. 25.00
2.4 MT)
104 Providing and fixing of Wall 25 mm dia SS Curtain Rod with approved Sqm. 10.00
Curtains (- Make -Gujarat furnishing -Mooshy collection design No. 22/ Pride- PR
- DS 1004) for Green room of approved colour fixed to the wall properly and SS
pipe shall be fixed to the wall by 50 mm ss flange including necessary hardware,
runners and accessiories, drilling, scaffolding, distance between two folds of
curtain shall not be more than 25mm, and cleaning etc..complete as required as
specified by EIC. (Elevational area of the opening shall be measured for
billing)
I-703


105 Providing & fixing in position 40 mm wide 16 guage SS Transition clipping 'T' Rmt. 10.00
patti of approved shape and pattern for flooring joint as per architectural drawing
and instructions including necessary hardware, drilling, cutting as specified and
as directed by Architect. (Running length of patti shall be measured for
billing)
I-703, I-709
106 Providing, making & errecting False Floor system as per architectural Sqm. 15.00
drawings & instruction. System consisting of concore steel panels, bare steel
panels of size 60cm x 60cm with following details. The floor panels made out of
hard cold rolled steel top sheet welded to a formed draw quality steel bottom pan
at assembly of each dome and multiple points along perimeter. The panels shall
be internally filled with lightweight cementitious product (Concore). The floor
panels shall be protected from corrosion by powder coat epoxy paint finish. The
understructure shall be with stringer system with finish floor height (FFH) of
200mm. The system shall be stringer system provide a range of adjustment upto
35mm total. The understructure supporting the panel shall be as follows
Refer Drw. No. I-210, I-211, I-213, I-830, I-607A, I-607B, I-706
Pedestal Assembly : Pedestal assembly to provide a means of leveling and

locking the assembly at a selected height which requires deliberate action to
change height setting and which prevents vibrating displacement.
Pedestal Heads : Consist of solid steel stud roll formed and press fitted into
head. Pedestal heads shall incorporate tabs, which accurately align the head with
the panel. The stud shall provide an anti rotation feature and vibration proof
locking device when engaged with the pedestal base assembly.
Pedestal Bases :Fabricated of a square base with not less than 100 cm sq.
assembled to a stud or tube, which is designed to engage the pedestal assembly,
secured to sub floor with adhesive or with screws. The tube shall be 2.22 Sq. Cm.
System performance: The panels shall be capable of supporting a minimum

concentrated load of 363 kgs. placed on one square inch area at any location with
maximum top surface permanent deflection not to exceed 2.4mm after load is
removed. The panels shall be capable of supporting a minimum uniform load of
1496 kgs. Per sqm. with maximum bottom surface permanent deflection not to
exceed 2.4mm after load is removed. The safety load of the floor system shall
provide a loading capacity of 953 kgs. On a one square inch area at any location
without failure. Failure is defined as the point at which the system will no longer
accept the load. The pedestal a


107 Antitermite Treament - providing & doing Antitermite treatment to wooden surface 0.00
such as doorframes, wooden partitions should be spreyed all sides of the wooden
surface with termisile chemical. Chemical mixing and application should be as per
manufacturar's specifications and instructions through approved agency with 15
yrs.Guarantee. solution should spreyed properly on required area. etc. completed
as required as specified by EIC
107.1 Anti-termite treatment to door frames. each 16.00
107.2 Anti-termite treatment to shutters & plan area. Sqm. 935.00
108 Providing, making and fixing in position custom made SS Signages as per 0.00
arcthitectural drawings and instructions with approved SS fixtures, approved base
including necessary hardware, farmas etc. complete as per detail drawing, as
specified and as directed by Architect.
108.1 Embossed sign with black paint (230mm x 230mm high in size) 0.00
109.1.1 Ladies - (230mm x 230mmc height in size) each 1.00
109.1.2 Gents - (230mm x 230mm height in size) each 1.00
109.1.3 Green Room Ladies- (600mm x 150mm height in size) each 1.00
109.1.4 Green Room Gents- (600mm x 150mm height in size) each 1.00
109.1.5 Fire Room- (600mm x 150mm heigh in size) each 1.00
TOTAL OF MISCELLANEOUS WORKS
TOTAL OF FINISHING WORK
III PLUMBING WORK

A SANITARYWARES & CP APPURTENANCES
Detail of Sanitary fixture are for the information of the Contractor, however model /
makes of all sanitary fixture shall be selected by Architect / Interior designer /
client and the same shall be binding for execution
No additional all fixing cost shall be paid for change in type of sanitary fixture or
fitting.
Provision of extension piece for final connection of CP fitting shall be supplied and
installed by the contractor accordingly (as required)


109 Providing & fixing first quality white vitreous china wall mounting wash basin (size each 2.00
as per architectural drawing) specially fabricated CI / MS brackets, painted with
two or three coats of enamel paint of approved shade over a coat of primer, 32
mm CP brass waste and CP brass cast bottle trap and pipe to wall with CP brass
flange and rubber adopter for waste connection complete including and wash
basin with approved type poly sulphide sealant, cutting and making good the walls
wherever required.
110 Providing & fixing following size, approved quality CP brass Waste coupling with each 3.00
brass check nuts conforming to IS 2963, including jointing with white zinc and
spun yarn and testing the joints for leak proofness all complete.
111 Providing & fixing following size approved quality CP brass Bottle trap with 32 each 3.00
mm size & connection pipe upto the wall and wall flanges including jointing with
white zinc and spun yarn & testing the joints for leak proofness etc. complete.
112 Providing & fixing 15 mm dia. CP brass Basin Tap, fixing the cock in position each 2.00
with inlet connection using white zinc and spun yarn testing the joints to a
hydraulic pressure of 10 kg / Sq.cm for leak proof joints etc. all complete as per
specifications.
113 Providing, fixing, testing and commissioning of C.P. brass angle valve with each 3.00
C.P. wall flange, Nut and Washer etc. complete as required.
114 Fixing, testing and commissioning of sink including providing & fixing C.I./M.S. each 1.00
Brackets (duly painted with 2 coats of paint over a coat of primer) C.P. cast brass
bottle trap with extension piece, rubber adaptor, wall flange, union, C.P. brass
chainrubber plug & making good. (wiithout drain board)For pantry area
115 Fixing, testing & commissioning of C.P. brass eurometic self closing pillar tap. each 1.00
116 Fixing push type liquid soap dispenser with PVC rawl plug & C.P. brass screw each 3.00
complete as required.
TOTAL OF SANITARYWARES & CP APPURTENANCES
WATER SUPPLY SYSTEM

117 Providing, Fixing , Testing & Commissioning of exposed ' C' class GI pipes
conforming to IS: 1239 with specials, fittings, clamps, brackets & internal working,
painted with two coats of enamel paint of approved shade and make, including
holes in walls, floors, R.C.C. slab/ beam and restoration of the same complete in
all respects.
117.1 15 mm dia. Rmt. 25.00

117.2 20 mm dia. Rmt. 25.00


118 Providing high pressure "HP" following size Lever Ball Valve assembly of
approved make (horizontal plunger screw type) conforming to IS 1703 with
brass or gun metal piston, back nut and PVC float, carbon steel handle PVC
coated conforming to IS 9762 and described in technical specifications.
118.1 15mm dia. each 1.00

118.2 20 mm dia. each 1.00
TOTAL OF WATER SUPPLY SYSTEM
B INTERNAL DRAINAGE SYSTEM

119 Spigot and socket centri cast iron drainage pipes & fittings of approved make and
with ISI mark conforming to IS 3989/ 84 for soil, waste pipes including all fittings
(plain or access door) e.g. bends, junctions, cowls, offsets, access pieces etc.,
jointed with lead joints, fixed with M.S. clamps & brackets including holes in
wall/floors and restoration wherever required as mentioned in technical
specification. (For Waste drainage)
119.1 80 mm dia Rmt. 50.00

119.2 50 mm dia Rmt. 5.00
120 Providing and fixing in position G.I. pipe and fittings of heavy class (c)
conforming to IS:1239 (for waste pipe from individual fixtures to floor trap / floor
drain & vent pipe) Including fixing at wall / ceiling level supported by galvanized
clamps and hangers providing two coats of synthetic enamel paint of approved
shade as per pipe colour code over a coat of primer or cutting & chasing in wall &
floors, providing protection to embedded GI pipes & fittings by wrapping of 400
microne polythene sheet over two coats of bitumen including proper overlaps in
joints complete as required and making good the chase by using 1:1 cement
mortar.
120.1 32 mm dia. Rmt. 12.00

120.2 40 mm dia. Rmt. 10.00
121 Providing and fixing in position 75 mm N.B. CI. Nahni traps of self cleaning design each 3.00
including 125 mm dia CP grating, joining, embedding in concrete etc. complete.
Rate to include making of opening in floor, marble / tiles, for fixing grating.
122 Providing and fixing Heavy class SS grating with Cockroach proof SS strainer of
approved design including setting in floor with cement motor to match with floor
finish as per architect requirement & suitable for waste and FD.
122.1 100 mm dia. each 3.00

TOTAL OF INTERNAL DRAINAGE SYSTEM
TOTAL OF PLUMBING WORK

IV FIRE ALARM SYSTEM & PUBLIC ADDRESS SYSTEM

A FIRE ALARM SYSTEM
Note:
The rate of each item of work for Fire Detection and Alarm System shall
also include the following :
1. Permission & NOC from statutory authorities, Inspection and Fees for Chief
Fire Officer, Any kind of Liasioning work with Authorities will be Re-embussed on
provision of Original Receipt
2. All Detector & Devices Mounted on TRUE Celling/Concealed in WALL will be
on metal Powder coated Junction Box 2mm thick with Glanding
3. All materials, fixing materials, accessories, appliances, tools and equipment.
4. Approved cover plates for inspection, junction and outlet boxes.

5. 2 mm thick outlet boxes and junction boxes.
6. All fixing accessories such as clips, nails, screws etc.
7. Providing and fixing approved saddles, hooks and grouting the same as
required, in the case of all exposed cable work.
8. Testing and commissioning of each device, circuit as per the requirements of
NFPA 72, TAC, local authorities and to be witnessed by the PMC / Consultant /
Client.
SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF OF THE
123 FOLLOWING EQUIPMENT/ Devices FOR FIRE ALARM SYSTEM
123.1 Multi Loop Microprocessor based 1 loops (each loop shall be able to connect Lot 1.00
minimum 124 detectors and 124 modules) intelligent, analogue addressable type
fire alarm control panel which can acomodate max 10 loops in each panel with 80
character LCD display, four access levels, 400 event historical logging, flash
EPROM sufficient numbers of programmable relay controls, 240 volts AC power
supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for
24 hours normal working and then be capable of operating the system for 2
hours during an emergency condition including all necessary software for
remote programming of fire alarm system through central control station.The
materials, appliances, equipment and devices shall be listed by a nationally
recognized approvals agency like UL864/FM/EN54 for use as part of a protected
premises protective signaling (fire alarm) system and smoke control system FACP
panle should be with standalone UPS (Location -COMMON AREA AT
GROUND FLOOR LEVEL)
123.2 Adressable Control modules For Fans, AHU Tripping & Fire Exhaust /smoke each 3.00
Extractas activation per specification
123.3 Adressable Monitor modules.as per specification each 2.00


123.4 Intelligent Analogue addressable photoelectric type smoke detector with mounting each 8.00
base, LED, Address switch, complete as per specifications
123.5 Intelligent addressable rate of rise cum fixed temperature heat detector with each 1.00
mounting base, LED, address switch complete as per specifications
123.6 Intelligent Analogue addressable photoelectric type beam detector with mounting each 2.00
base & reflector, LED, Address switch, complete as per specifications
123.7 Addressable type manual Break glass (Pull station) unit as per specifications each 2.00
123.8 Surface mounted addressable type fully solid state circuitory dual tone Electronic each 2.00
loud speaker type hooters with strobe lights of 110 Cd intensity as per
specifications
123.9 Addressable Fault Isolation Module as per specifications each 1.00
124.10 Response Indicator as per Specification each 1.00
TOTAL OF FIRE ALARM SYSTEM
B CABLES & ACCESSORIES

CABLES & ACCESSORIES FOR FAS
Note : All the items from Fire alarm control panel, Repeater Panel, Monitor
module, Control module, Smoke detector, Heat detector, Multicrieria type smoke
detector, Manual break glass unit, Hooter, Fault isolation module,Telephone
Jack, Responce indicator and Magnetic door condact mentioned above shall be
termed as Devices for the cable measurement purpose. Outgoing cables from
Control module & monitor module will not be measured seperately.
124 Supplying, terminating, testing and commissioning of cabling for fire detection Per Device 25.00
and alarm system with 2C x 1.5 sq mm annealed tinned copper conductor Red
coloured PVC sheathed FRLS armoured cables as per specifications. FR grade
and ISI marked as per relavent IS standards and specifications. Cables shall be
estimated as per the drawings. Cabling for response indicator/ power
/communication cable shall not be considered seperatelyas device. The cost of
the same shall be included in the unit rate estimated for per device. Laying
supervision is under IBMS contractor scope. Cabling for response indicator/
power /communication cable shall not be considered seperatelyas device. The
cost of the same shall be included in the unit rate estimated for per
device(i.e.Cable from FACP panel to First Detector/device ,Last Detector/device
& return to Panel ,Detector to detector/device,Power from Hooter to Hooter and
FACP panel l)
TOTAL OF CABLES & ACCESSORIES
TOTAL OF FIRE ALARM SYSTEM & PUBLIC ADDRESS SYSTEM

V ELECTRICAL WORK
GENERAL NOTES
Required clearances from the concerned statutory authorities are in the scope of
this work.Statutory fees paid will be reimbursed on production of original receipts
in the name of IITB.
A POINT WIRING IN PVC CONDUIT, TELEPHONE WIRING, T.V WIRING
ETC.
125 Point wiring in PVC conduit (HMS variety)
Point wiring for light/ceiing fan/6A/ 16A/ socket outlet /6A outlet for exhaust fan,
bell point etc. with 1.1 KV grade FRLS PVC insulated multistranded copper
conductor wire(ISI marked), in 25 to 40 mm dia High mechanical stress (HMS)
rigid PVC conduit having ISI marked IS 9537 Part - 3, including fixing accessories
& hardware concealed /exposed in slab/wall or on 5mm. thick G.I. spacers fixed
with no. 10 nettle within the box piece fold wood screws with nylon plug complete
with all conduit accessories 20 SWG G.I. Saddles, ready made MS modular
switchboxes, socket outlet boxes of approved makes including termination inside
sw/sockets with using copper lugs ,zinc chromate passivated, brass earthing stud
1/2 nos, controlling modular switches, sockets with moulded front plate and inner
plate etc. including appropriate size of FRLS PVC insulated copper earth wire,
brass/bakelite (straight / angular) lamp holders, 3 plate ceiling rose,16 A,
connectors, painting etc. as per specifications and drawings and as directed by
E.I.C.and as detailed below : (sample switch Box etc. to be got approved before
fabrication)
NOTE:
1. Connections shall be done with crimped type tinned copper lugs & washers.
2. All switches & socket outlets shall be as per preferred makes.

3. All 16 A socket outlets should be with 6 pin & shuttered type
4. MS boxes other than switch boxes & socket outlet boxes shall be fabricated out
of 16 SWG thickness MS sheet duly painted with red oxide primer & 2 coats of
synthetic enamel paint.
5. Minimum size of the FRLS insulated copper earth wire continuity shall be 2.5
sq.mm.
6. The colour shade of switches & cover plates shall be white /off white & to be
approved by architect.
7. The scope also includes supply of modular blanking plates where ever
required.
8. The maximum permissible number of PVC insulated wires through PVC
conduits shall be as per Tech Specs.
9.Test certificates shall be provided along with delivery of wires.


10. In case of Primary point controlled by switch,cost shall include wiring from DB
to switch board, Switch board to Occupancy sensor (Toilet blocks) & any looping
from Switch board to Switch board shall be part of point wiring .
11. Light point wiring cost shall include connection of fixture from ceiling rose with
3 core 1.5sqmm copper flexible cable.
125.1 Ceiling Mounted Lights In Sitting Area
126.1.1 Primary Light point with 2 nos of 2.5 sq.mm wires alongwith 1 no of 2.5 sq.mm Pt. 18.00
insulated earth wires controlled by 10A SP MCB in the DB. Excluding cost of MCB
as per specification.
126.1.2 Secondary light point with 2 nos of 1.5 sq.mm wires alongwith 1 no of 2.5 sq.mm Pt 56.00
insulated earth wire looped to item above as per specification.
125.2 Step Lights On Chair
125.3 Color Lights On Stage
125.4 Auditorium Foot Lighting
125.5 Post Function Area Lighting
125.6 Room Lighting
126.6.1 Wiring with 25mm dia HMS FR PVC conduit embedded or surface mounted as Pt 5.00
including cost of junction boxes, bends, elbows, sockets, tees etc. laying in slab,
cutting chasis and making good wherever called for or surface mounted including
all fixing hardware along with 3 nos - 2.5 sq.mm PVC insulated multi stranded
flexible FRLS copper wires from DB to Switch board near the entrance of room
and necessary accesories required to complete the job in an approved manner as
per instruction of Engineer In Charge as per specification. (As per scheme &
layout)


insulated earth wires operated from 6A switch including cost of ceiling rose &
flex.wire as per specification.Only point wiring cost to be considered.
125.7 Pre Function Area
125.8 Cove Lighting
TOTAL FOR POINT WIRING IN PVC CONDUIT, TELEPHONE WIRING,
T.V WIRING ETC.
B LIGHT FIXTURES AND FITTINGS, CEILING FANS, EXHAUST FANS ETC
126 Light Fixtures & Fittings:

Supply, installation, testing & commissioning of fixtures & fittings, ceiling fans,
exhaust fans, etc. complete with accessories, tube/lamp etc in on surface of
slab/beam by 2 nos (minimum) of 6 mm anchor fasteners or on wall with 2 nos of
wood screws, nylon plug etc., suitable supporting frame fixed with rag bolts
grouted on the wall/anchor fastener on the beam/on the column & other fixing
accessories etc provision & connection with 1.5 sq.mm multistranded copper
conductor FRLS PVC wires etc., all as per drawing, specifications & as per the
instruction of E.I.C.
Note:
1) Sample fixture/fittings shall be got approved from Department and Architects
with complete technical data.
2) The Cat No. indicated below is only indicative.
3) Cost of lamps to be included in installation rate.
4) All fixtures shall be with low loss electronic ballast
5) T5 High Efficiency Lamps control Gear with 10% Total harmonic distortion
(THD)
126.1 Philips Make 1X 70 W CDMT MSB 150 HF downlighter each 33.00
126.2 Philips Make 2X26 W PL-C/2P FBH225 downlighter (with dimmable ballast) each 37.00
126.3 Philips Make 1X28 W T5 V2 VECTOR TCH207 strip fitting each 30.00


126.4 Philips Make 1X70 W BCG 530 Stage track light with tracks as per drawings. each 8.00
126.5 Philips Make 1X11 W FOOT LIGHT BWG 150 each 12.00
126.6 Prolite Make 1 X 11 W PLE 111 E/NM emergency EXIT signage light with each 4.00
Maintainance free batteries for 3hrs Backup
126.7 Philips Make 1X3 W STEP LIGHT(Only lamp with ballast) each 72.00
126.8 Philips Make 1X18W PL Circular down lighting FBS 085 each 14.00
126.9 Philips Make Colorblast Powercore RGB Stage Light (Procenium Mounting) each 2.00
127.10 Philips Make white LED strip light with driver for cove lighting Rmt. 75.00
127.11 DIN Rail mount, 12-Channel Ballst Controller, suitable for 0- of Make- each 1.00
Philips.programmable. Input Power: 1-Phase, 220VAC, 50Hz. To be connected
dimming along with suitable type of dimmable ballst. All the 10VDC/DSI/DALI
Broadcast type (DDBC1200)
127.12 DIN Rail mount, 12-Channel Relay, suitable for 20 A (inductive) On/Off control per each 1.00
channel.Total 12 Chanel Relay capable of 180 A load. All the Channels are
independentlyprogrammable. Input Power: 1-Phase, 220VAC, 50Hz. To be
connected on Dynet network.Make-Philips.(DDRC1220FR-GL)
127.13 Smart switch location to be sujested by Architect / Client .Low-voltage, User each 3.00
interface keypad with 7 Buttons, Standard steel Finish.(DUS 804C)
127.14 Multi Sensor for IR Receiver, motion control.The operation of sensor is Subject to each 2.00
Height of False Celing. Ideally it is suitable for 2.5 Meter height.
127.15 IR Handheld remote. (DTK 508) each 1.00

127 Supply, installation, testing & comissioning of following ceiling fans with double
ball bearing with standard downrod, canopies, shackles, blades with safety cable
suspension (Secondary support safety cable) white colour with all accessories
including continous earthing and final connection with 24/0.2 mm dia copper
conductor 2/3 core twisted PVC flexible wire etc but without speed regulator,
suitable for operation on any type of 100 W noise free capacitor type fan regulator
on 230 V 50 Hz single phase AC supply conforming to IS 374/79 with latest
amendments all as per specifications & instructions of E-I-C.
127.1 1400 mm sweep ( High Breeze Cropton make ) each 1.00

127.2 Wall Mouting Fan each 2.00
127.3 Fan Hook Boxes 0.00
128 Supply, installation, testing of concealed fan hook boxes of size 125 x 125 x each 1.00
75mm deep fabricated out of 2mm thick M.S CRCA sheet with 12.5 mm dia M.S
tested rod hook with brass earthing stud & welded nut from inside and 2mm thick
round M.S cover plate overlapping by 10 mm, including red oxide and two coats
of white synthetic enamel paints and brass chromium plated screws and cup
washers for fixing and instruction of Engineer-in-charge (Sample box with cover
to be got approved before fabrication including the fabricator)


TOTAL OF LIGHT FIXTURES AND FITTINGS, CEILING FANS, EXHAUST
FANS ETC
C POWER POINT WIRING

129 Power Point Wiring FRLSom DB MCB to 16A socket outlet with 2 x 4.0mm2 + 1 x
2.5mm2 stranded/flexible copper wires with FRLS type PVC insulation as per IS
694 latest for primary point and 2 x 2.5mm2 + 1 x 1.5mm2 stranded/flexible
copper wires with FRLS type PVC insulation as per IS 694 latest for secondary
point; 25 mm Dia. MS conduit and accessories such as couplers, bends, junction
boxes, inspection elbows. Conduits shall be installed or cleated surface to ceiling
or wall with saddles or spacers; installed concealed in walls or floor as required
and as directed by the project incharge and as indicated in the approved shop
drawings. Rate shall include supply and installation of the following items:
1) 1.6/2.00mm, 25 mm Dia. PVC MMS conduit
2) Copper/PVC FRLS wires.
3) Associated civil works such as chasing the wall or floor and making good to
rough finish with plaster so that the conduit is properly concealed.
129.1 S/I/T/C of Primary point 6A modular type switched socket outlet complete with each 10.00
flush mounting GI back box with earth terminal, civil works and making good to
rough finish plaster so that the box is lined and levelled including wiring as
expressed above complete in all respect.
129.2 S/I/T/C of Secondary Point 6A modular type switched socket outlet looped each 10.00
FRLSom above point complete with flush mounting GI back box with earth
terminal, civil works and making good to rough finish plaster so that the box is
lined and levelled.
129.3 S/I/T/C of Primary point of 6/16A modular type switched socket outlet complete each 15.00
with flush mounting GI back box with earth terminal, civil works and making good
to rough finish plaster so that the box is lined and levelled including wiring as
expressed above complete in all respect.
129.4 S/I/T/C of Secondary Point 6/16A modular type switched socket outlet looped each 26.00
FRLSom above point complete with flush mounting GI back box with earth
terminal, civil works and making good to rough finish plaster so that the box is
lined and levelled.
129.5 AC Points
130.5.1 S/I/T/C of Primary point of 20A modular type switched socket outlet complete each 4.00
expressed above complete in all respect.(for AC)
129.6 UPS Points


130.6.1 S/I/T/C of Primary point of 6/16A modular type switched socket outlet complete each 16.00
expressed above complete in all respect.(ups primary point)
130.6.2 S/I/T/C of the 6/16A modular type switched socket outlet looped FRLSom above each 29.00
point complete with flush mounting GI back box with earth terminal, civil works
and making good to rough finish plaster so that the box is lined and levelled. (ups
secondery point )
129.7 Telephone Point Wiring:

130.7.1 Point wiring with 4 pair 0.50 sq.mm. Telephone copper conductor PVC insulated,
in 25-40mm dia rigid FR-PVC conduit modular box (HMS variety - ISI
marked,conforming to IS 9537 Part-III) concealed in slab /wall or surface with
5mm thick G.I.spacer & 20 SWG GI Saddle fixed with nylon plug, wood screws
etc. complete with all conduit accessories suitable MS pull boxes of suitable sizes
as per site condition wherever required M.S. telephone point accessories boxes
fabricated out of min 18 SWG thick CRCA sheet zinc chromate passivated, brass
earthing studs 1/ 2 nos., RJ-11 telephone socket outlets with shutter ferrule
numbers on both side of the circuits all terminations with ferrule /lugs if required,
labelling all as per drawing specifications & as per instructions of E-I-C. as per
specification.
NOTE:
1. Point wiring means 4 pair 0.50 sq.mm wires from Telephone Tag Block in
Tel/LAN shaft to the assigned point including end termination of one pair at both
sides and other pairs should be kept spare.
2. G.A drawings & fabrications drawing are to be got approved from E-I.C.
3. Approved makes for Telephone wire : FINOLEX / ITL/ POLYCAB
130.7.2 Point wiring for telephone point with 4 pair 0.50 sqmm wire with RJ 11 jack type Pt. 4.00
socket with shutter in a box with connector as per specification.
129.8 Supply, installation, testing & commissioning of following Krone connector

telephone tag block box, readymade 18 SWG MS CRCA sheet,
concealed/surface mounted on MS frame of size 40 x 40 x 5mm and grouted on
the wall/fixed on the column free standing type with anchor fasterners, cable
end/wire way box with adequate space facility to be provided in the TTB, with front
operable hinged door, cam type locking arrangement, neoprene rubber/cork
gasket for joints, ring type wire bunching clamps at 4 corners, name plate etc. all
as per standards, specification, drawing & instructions of E.I.C as per
specification.
Note:
1) Point distribution diagram shall put in side the DB with polythene protective
cover.
2) All fabrication drawings shall be got approved.


3) Final coat of painting shall be done at site after installation if required.
4) Disconnection module shall be Krone Part No. 69011006-02 or as specified in
the list of approved makes.
10 pair telephone tag box : Set 1.00
A set consisting of :
1) Disconnection module 2 /10 --> 1 nos.
2) Back mounting frame 2/10, 1 way suitable for mounting 1 no's of 2/10
modules. -->1nos (C.T. box with mounting bracket)
3) Transparent dust cover --> 1 no. complete with all accessories
4) Label Holder - 1 no
TOTAL FOR POWER POINT WIRING
D UPS
130 Supply, installation,testing and commissioning of 10 KVA online UPS System each 1.00
(Three Phase In & Single Phase Out) with Inbuilt SMF batteries and 15 minutes of
battery backup.
131 Supply, installation,testing and commissioning of following MCB's in powder
coated enclosures.
131.1 32A 4P MCB 'C' curve each 1.00
131.2 63 A DP MCB 'C' each 1.00
132 Supply, installation,testing and commissioning of following sizes of stranded FRLS
copper wire inside flex.PVC conduits including termination at both the ends.
( MCB's mentioned in item no.2 & UPS terminal box.)
132.1 4 sq.mm. x 4 nos in 32 mm Flex. PVC conduit ( for incoming) Rmt. 2.00
132.2 10 sq.mm x 2 no's in 25 mm Flex.PVC conduit for Outgoing. Rmt. 2.00
TOTAL FOR UPS SYSTEM
E DISTRIBUTION BOARDS
READYMADE DISTRIBUTION BOARDS


133 Fabrication, inspection at works Supply, installation, testing & commissioning of
following readymade distribution boards, double door, IP 42 degree protection
complete with necessary, MCB isolators, MCBs, earth leakage circuit breaker
(ELCB) etc including interconnections with appropriate capacity size of PVC
insulated copper conductor wires (ISI marked),suitable for concealed mounting
/wall mounting with MS frame work of 40 x 40 x 5 mm MS angle iron, with M.S.
enclosure fabricated out of min 16 SWG thick M.S. CRCA sheet with concealed
hinged door, locking arrangement etc. including earthing clamps for both incoming
& outgoing circuits, interconnections, per phase isolation kit as required,cable end
box & wire way box if required, continuous copper earth wire in the wire way box
with single/duplicate brass earthing terminals, danger board, name plate, flexible
earthing for the door, metal treatment & powder coated painting, Phase
Distribution drawing etc. all as per drawings (G.A. & fabrication drawing to be got
approved), etc. relevant IS & instruction of Engineer-in-charge.
Note:
1.MCBs shall be minimum 10 KA breaking capacity (Type –C)
2. Blanking Plates shall be included in scope of work.
3. DB shall be of standard readymade type as per catalouge No. from approved
manufacturers as indicated in preferred makes of material.
4. Wire way & cable end box also end & locking plates shall be provided.
5. Routine tests will be conducted at factory in presense of user as per relevant
IS.
All Electrical component should have IS mark
Note:
133.1 DB :(12way TPN DB) Set 2.00
a) 63 A 4P MCB as incomer -- 1 No.
b) 63 A, 2 pole RCCB with 30mA sensitivity - 3Nos.
c) 6 - 32 A SP MCB -- 36 nos
d) 12 way brass neutral links -- 4 Sets.
e) Brass earth links - 1 Sets
e) Brass earth links - 1 Sets
133.2 UPSDB (AV System) Set 1.00
16Way SPN Emergancy Lighting Distribution Boards comprising of:
Incomer:63A DP MCB
16 nos. of 10/16/32A SP MCB C curve, 10kA
Enclosure IP 43 double door PPI Kit
TOTAL OF DISTRIBUTION BOARDS
F L.T.CABLES, END JOINTS & CABLE MARKER

134 LT. Cables


Supply, handling, laying effecting proper connections testing and commissioning
of following sizes of 1.1 KV grade PVC / XLPE core insulated, extruded PVC inner
sheath, armoured / unarmoured extruded outer sheath FRLS PVC, Copper /
Aluminium conductor cables as per IS 7098 Part I laid over MS supports, cable
racks, trenches, or fixing on walls including clamping the cable to supports in an
approved manner along with cable . (Earthing will be measured separately and
need not be quoted under this item). All complete as required and as per final
instruction as given by E.I.C / Consultants.
134.1 4 C x 10 sq.mm., XLPE Al. Armoured cable Rmt. 40.00

134.2 3 C x 10 sq.mm., XLPE Al. Armoured cable Rmt. 80.00
135 CABLE TERMINATION
Supply and making terminal joints for the following sizes of 1.1KV grade PVC /
XLPE Insulated armoured / unarmoured Copper / Aluminium conductor cables
including providing heavy duty bimetallic, crimping type terminal lugs wherever
Aluminium conductor cables are used Copper Gland Earthing as directed by
E.I.C., insulation tape, heavy duty double compression type brass glands effecting
terminal connection to the equipment/Panel complete as required as per final
direction and approval of the Owner/Consultant.
135.1 4 C x 10 sq.mm., XLPE Al. Armoured cable each 4.00

135.2 3 C x 10 sq.mm., XLPE Al. Armoured cable each 2.00
TOTAL FOR L.T.CABLES, END JOINTS
G EARTHING SYSTEM
136 Supply, installation, testing & commissioning of earthing system & associated
accessories, etc. complete all as per the instructions of E.I.C.
Note :
1) Measurements of resistance of each earth station & resistance of complete
scheme of earthing layout must be measured recorded & got approved by E.I.C.
2) Jointing of the earth strip shall be with brass nuts bolts and also with solder
joints.
3) Jointing of the earth wire shall be with solder joints with tinned cable sockets
136.1 Supply & making Tinned Cu. earth plate electrode 600 X 600 X 3.15 mm earth each 2.00
station 2.5 m below ground level conforming to IS 3043 including 2 nos of 50 x 6
mm Copper earth strips from earthing plate upto the ground level inside the
chamber with all required materials like coke /charcoal, salt, brass nut-bolt &
washers, watering arrangement, G.I. Pipe (B class) concrete chamber of 450mm
x 450mm x 450mm deep, thick chequered plate hinged cover with locking
arrengement mounted on 40x40x5 mm thick angle iron frame & excavation in all
types of soil in ground refilling & removal of excess earth within radius of 2 km.
within IITB campus etc.


NOTE
1) The chamber cover & frame shall be hinged type & it shall be got approved by
department.
136.2 Supply & Laying Tinned copper earth wire/earth strip fixed on wall/side of
trench/slab /column /beam/ shaft connection to panel/DBs/SFU's etc. with 5mm.
Thick G.I. Spacers & 2mm thick G.I. Saddle
137.2.1 32 x 6 mm thick tinned copper tape. Rmt. 30.00
137.2.3 8 SWG Copper wire Rmt. 50.00
136.3 Supply & Laying of following earthing tapes in already laid hume pipes with
interconnection of earth strip/wire with brass bolt, nuts & washers & solder
jointing.
TOTAL OF EARTHING SYSTEM
TOTAL OF ELECTRICAL WORKS
VI HVAC WORK
137 Supply, Installation, Testing & Commissioning of Double Skin Air Handling Unit each 1.00
25mm thick panel as per Tech.specifications.
Outer Skin : GSS 0.63mm Preplasticised
Inner Skin : GSS 0.63mm Plain
6RD Dx. Cooling Coil with 3 independent circuits / 48TR Capacity
MERV 13 Filters
Plug type / Backward Curved Fan of 11200 CFM
TEFC Induction Motor EFF1
Insulated SS Drain Tray
138 Supply, Installation, Testing & Commissioning Prefabricated Rectangular 120GSM
GSS Ducting + Rolamate Flanges + Proper Supportiong arrangement
138.1 22G Sqm. 220.00

138.2 18G Sqm. 50.00
139 Supply, Installation, Testing & Commissioning Prefabricated Round 120GSM GSS
Ducting + Flange less joints + Single Hanger Supporting arrangement
139.1 22G Sqm. 90.00

140 Supply, Installation, Testing & Commissioning Duct Thermal Insulation 25mm Sqm. 195.00
Closed Cell Nitrile Rubber for Exposed Ducts covered with 24G Al.Cladding
141 Supply, Installation, Testing & Commissioning Duct Acoustic Insulation using
25mm thick Open Cell Nitrile Rubber
141.1 ARMASOUND covered with 28G Al.Perforated Sheet Sqm. 360.00


142 Supply, Installation, Testing & Commissioning Sound Attenuator to maintain sound
pressure at 45 dB A
142.1 W1100 x H1100 x L 1200 each 1.00
142.2 W1400 x H1400 x L 1200 each 1.00
143 Supply, Installation, Testing & Commissioning Motorised Smoke & Fire Damper Sqm. 4.00
with Sleeve & Comprising of following,
143.1 ON/Off Spring Return Actuator of 10NM each 2.00
143.2 Fire Damper Electrical Panel each 2.00
143.3 CO2 Sensor each 1.00
144 Supply, Installation, Testing & Commissioning Motorised Modulating VCD for Sqm. 3.00
Fresh Air & Comprising of following,
144.1 Modulating Actuator 10NM each 1.00
144.2 CO2 Sensor each 1.00
144.3 Electrical Panel each 1.00
145 Supply, Installation, Testing & Commissioning GSS VCD for Round Duct Sqm. 2.00
146 Supply, Installation, Testing & Commissioning Propeller Exhaust Air Fan of 1000 each 4.00
CFM / 10mm st. with Gravity Louver
147 Supply, Installation, Testing & Commissioning Extruded Aluminum Powder Coated each 30.00
Flush Type four side flange Grille with VCD for Round Ducting
500mm x 150mm Ht
148 Supply, Installation, Testing & Commissioning Linear Continuous Grill for Return
Air 300mm wide
148.1 300mm wide Rmt. 54.00
148.2 600mm wide Rmt. 7.00
149 Modification of Existing MS Refrigerent Piping with Recharging of R22 as per the Lot 1.00
drawings.
150 Dismantling of Existing GSS Ducting & lifting / shifting to a location as mandated Lot 1.00
by IITB within the campus of IITB.
151 Dismantling of Existing AHU & shifting it to a location as mandated by IITB within Lot 1.00
the campus of IITB.
152 Supply, Installation, Testing & Commissioning Cassette Type Split Unit of 2 TR each 2.00
with Copper Piping upto 10mtr Distance with Scroll Compressor
153 Supply, Installation, Testing & Commissioning Hi Wall Type Split Unit of 1.5 TR each 1.00
with Copper Piping upto 10mtr Distance with Scroll Compressor
TOTAL OF HVAC WORK

MS & HVAC WORKS)
hall also be inclusive of
ng & corrugate GI sheet for a height up to 3m to

ng the same after completion of the work without
ur etc and nothing shall be paid extra on

excavation and transporting earth , debris, and
where direct access is non existing and
while movement/ deployment of materials &
ng to IS 2750 -latest revision.
ations and to be strictly adhered by employing
ngineer-in-charge
oval of Engineer-in-charge
of existing traffic and damages caused any to
l labour problems and any other matter relating

ature of tenderer with Date & seal:

Rate Amount
0
0

Rate Amount
0

Rate Amount

Rate Amount

Rate Amount

Rate Amount
0
0
0
0
0

Rate Amount

Rate Amount
0

Rate Amount
0

Rate Amount
0
0
0
0
0
0

Rate Amount
0
0
0
0
0
0

Rate Amount
0
0
0
0
0
0
0
0
0

Rate Amount
0

Rate Amount
0

Rate Amount
0

Rate Amount

Rate Amount
0
0
0
0
0

Rate Amount
0
0
0
0

Rate Amount
0
0
0
0
0

Rate Amount
0
0
0
0

Rate Amount
0
0
0

Rate Amount

Rate Amount
0

Rate Amount
0

Rate Amount
0

Rate Amount
0

Rate Amount
0

Rate Amount
0

Rate Amount
0

Rate Amount
0

Rate Amount
0

Rate Amount
0

Rate Amount

Rate Amount
0

Rate Amount
0
0
Item Deleted
0
0
0

Rate Amount
0
0
0
0

Rate Amount
0
0
0
0

Rate Amount
Item deleted

Rate Amount
0

Rate Amount
0

Rate Amount
0

Rate Amount

Rate Amount

Rate Amount
0
0
0
0

Rate Amount
0

Rate Amount
0

Rate Amount

Rate Amount
0
0
0

Rate Amount
0
0
0
0
0
0
0
0
0
0

Rate Amount

Rate Amount
0
0
0
0

Rate Amount

Rate Amount
0
0

Rate Amount
0
0
0

Rate Amount
0
0
0
0
0
0
0
0
0
0

Rate Amount
0

Rate Amount
0

Rate Amount
0
0
0
0
0

Rate Amount

Rate Amount
0
0
0
0
0

Rate Amount
0
0
0
0
0
0
0
0
0
0

Rate Amount
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0

INDIAN INSTITUTE OF TECHNOLOGY BOMBAY Construction of Security Cabins and Allied Infrastructure Works at Entrance area
SR. NO. DSR ITEMS ITEM DESCRIPTION AMOUNT RS.

1 TOTAL OF C.P. & SANITARY FIXTURE 85,661.25
2 TOTAL OF WATER SUPPLY 47,380.30
3 TOTAL OF INTERNAL DRAINAGE 95,546.03
4 TOTAL OF EXTERNAL SEWAGE 109,914.39
5 TOTAL OF CIVIL WORK 46,882.89
6 TOTAL OF RAIN WATER 49,896.83
TOTAL OF PLUMBING WORKS - DSR ITEMS 435,281.70
NON-DSR AMOUNT RS.

SR. NO. ITEM DESCRIPTION
ITEMS
TOTAL OF PLUMBING WORKS - NON-DSR ITEMS -
TOTAL OF PLUMBING WORKS - ( DSR ITEMS + NON-DSR 435,281.70

ITEMS)
Operative
SR.NO. DSR 2007 Description Unit Qty Rate Cost Index Amount
Rate
A B C D E F G H=FXG I=EXH
C.P. & Sanitary Fittings & Accessories
Providing and fixing white vitreous china pedestal type

water closet(European type W.C. pan) with seat and lid, 10
litre low level whiteP.V.C. flushing cistern with manually
17.2
1 controlled device (handle lever),conforming to IS : 7231,
with all fittings and fixtures complete includingcutting and
making good the walls and floors wherever required
17.2.1 W.C. pan with ISI marked white solid plastic seat and lid each 11.00 2152.50 1.39 2991.98 32,911.73
TENDER DOCUMENT - VOLUME 2 OF 2. BILL OF QUANTITIES 132SEAL OF TENDERER

Operative
Rate
Providing and fixing white vitreous china flat back or wall

corner type lipped front urinal basin of 430 x 260 x 350 mm and
340 x 410 x 265 mm sizes respectively with automatic flushing
17.4 cistern with standard flush pipes and c.p. brass unions and G.I.
clamps complete, including painting of fittings and brackets,
cutting and making good the walls and floor wherever required.
2
One urinal basin with 5 litre white PVC automatic flushing

17.4.1 each 1.00 2018.70 1.39 2805.99 2,805.99
cistern.
Range of four urinal basins with 10 litre white

17.4.4 each 2.00 6062.20 1.39 8426.46 16,852.92
P.V.C.automatic flushing cistern
Providing & fixing wash basin with C. I. bracketes, 15mm C. P.

brass pillar taps, 32mm C. P. brass waste of standard pattern,
17.7 including painting of fittings and brackets, cutting and making
3 good the walls wherever require:
White Vitreous China Wash basin size 630x450 mm with apair

17.7.1 each 11.00 1332.90 1.39 1852.73 20,380.04
of 15 mm C.P. brass pillar taps.
Providing and fixing mirror of superior glass (of approved

quality) and ofrequired shape and size with plastic moulded
17.32
4 frame of approved makeand shade with 6 mm thick hard board
backing :
17.32.2 Rectangular shape 453x357mm each 11.00 465.10 1.39 646.49 7,111.38
17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Operative
Rate
5 Bottle trap 31mm single piece moulded with height of

270mm, effective length of tail pipe 260mm from the centre of
17.70.1 each 11.00 366.20 1.39 509.02 5,599.20
the waste coupling 77mm breadth with 25mm minimum
water seal, weighing not less than 260gms.
Total of C.P. & Sanitary Fittings & Accessories 85,661.25

Water Supply
Internal work
Providing & fixing G. I pipes complete with G. I. fitting and
18.11 clamps i/c making good the walls etc. concealed pipe including
6 painting with anticorrosive bitumastic paint, cutting chases and
making good the wall
18.11.1 15 mm dia nominal bore metre 100.00 144.75 1.39 201.20 20,120.25
External work
Providing & fixing G. I pipes complete with G. I. fittings
18.12
7 including trenching and refilling etc.
18.12.3 25 mm dia. Nominal bore metre 30.00 156.85 1.39 218.02 6,540.65
18.15 Provding & fixing brass bib cock of approved quality
8
18.15.1 15 mm nominal bore each 11.00 1.39 0.00 -
Providing and placing on terrace (at all floor levels)

polyethylenewater storage tank ISI : 12701 marked with cover
9 18.48 and suitable lockingarrangement and making necessary holes per litre 2000.00 5.25 1.39 7.30 14,595.00
for inlet, outlet andoverflow pipes but without fittings and
the base support for tank

Operative
Rate
Providing and fixing C.P. brass angle valve for basin mixer and
18.53 geyser points of approved quality conforming to IS:8931 a)
10 15 mmnominal bore
18.53.1 15mm nominal bore each 347.65 each 11.00 347.65 1.39 483.23 5,315.57
Providing and fixing unplasticised P.V.C. connection pipe with

18.74 PTMT Nuts collar and bush of approved quality and colour.
11
18.74.2 15 mm nominal bore with 45 cm length. each 11.00 52.90 1.39 73.53 808.84
Total of Water Supply 47,380.30
Internal Drainage
17.35 Providing and fixing soil, waste and vent pipes :
17.35.1 100 mm dia
17.35.1.2 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 metre 26.00 730.00 1.39 1014.70 26,382.20
12
17.35.2 75 mm diameter
17.35.2.2 Centrifugally cast (spun) iron socketed pipe as per IS: 3989 metre 79.00 629.85 1.39 875.49 69,163.83
Total of Internal Drainage 95,546.03

External Sewage
Providing, laying and jointing glazed stoneware pipes class SP-1
withstiff mixture of cement mortar in the proportion of 1:1
19.1
13 (1 cement : 1fine sand) including testing of joints etc.
complete :
19.1.2 150 mm diameter metre 100.00 151.65 1.39 210.79 21,079.35

Operative
Rate
Providing and laying cement concrete 1:5:10 (1 cement : 5

coarsesand : 10 graded stone aggregate 40 mm nominal
19.2
14 size) all-roundS.W. pipes including bed concrete as per
standard design
19.2.2 150 mm diameter S.W. pipe metre 100.00 405.05 1.39 563.02 56,301.95

Operative
Rate
Providing and fixing square-mouth S.W. gully trap class SP-

1complete with C.I. grating brick masonry chamber with water
19.4 tight C.I.cover with frame of 300 x300 mm size (inside) the
15 weight of cover tobe not less than 4.50 kg and frame to be not
less than 2.70 kg as perstandard design :
19.4.1 100x100 mm size P type

19.4.1.1 With F.P.S. Bricks class designation 75 each 2.00 935.15 1.39 1299.86 2,599.72
Constructing brick masonry manhole in cement mortar 1:4 ( 1

cement: 4 coarse sand ) R.C.C. top slab with 1:2:4 mix (1
cement : 2 coarsesand : 4 graded stone aggregate 20 mm
nominal size), foundationconcrete 1:4:8 mix (1 cement : 4
coarse sand : 8 graded stoneaggregate 40mm nominal size)
19.7 inside plastering 12mm thick withcement mortar 1:3 (1
cement : 3 coarse sand) finished with floatingcoat of neat
cement and making channels in cement concrete 1:2:4(1
cement : 2 coarse sand : 4 graded stone aggregate 20mm
16 nominalsize) finished with a floating coat of neat cement
complete as per standard design
Inside size 90x80 cm and 45 cm deep including C.I. coverwith

frame (light duty) 455x610 mm internal dimensionstotal
19.7.1 weight of cover and frame to be not less than 38 kg(weight of
cover 23 kg and weight of frame 15 kg) :
19.7.1.1 With F.P.S. bricks with class designation 75 each 4.00 5383.70 1.39 7483.34 29,933.37
Total of External Sewage 109,914.39

Operative
Rate
Civil Work
Providing and fixing 18mm thick gang saw cut mirror

polished premoulded and prepolished) machine cut for kitchen
platforms, vanity counters, window sills , facias and similar
locations of required size of approved shade, colour and texture
laid over 20mm thick base cement
8.2 mortar 1:4 (1 cement : 4 coarse sand) with joints treated
17 with white cement, mixed with matching pigment, epoxy
touch ups, including rubbing, curing, moulding and polishing
to edge to give high gloss finish
etc. complete at all levels.
8.2.2 Granite of any colour and shade

8.2.2.2 Area of slab over 0.50 sqm. sqm 9.00 2,575.10 1.39 3579.39 32,214.50
Extra for providing edge moulding to 18mm thick marble

stone counters, Vanities etc. including machine polishing to
8.3
18 edge to give high gloss finish etc. complete as per design
approved by Engineer-in-Charge.
8.3.2 Granite work metre 15.00 97 1.39 134.83 2,022.45
Providing and fixing stone slab table rubbed, edges

rounded andpolished of size 75x50 cm deep and 1.8 cm
thick fixed in urinal partitions by cutting a chase of
appropriate width with chase cutter andembedding the stone
8.10
19 in the chase with epoxy grout or with cementconcrete
1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate
6mm nominal size) as per direction of Engineer-in-charge
and finishedsmooth.
8.10.1 White Agaria Marble Stone sqm 4.00 2274.45 1.39 3161.49 12,645.94

Operative
Rate
Total of Civil Work 46,882.89

Operative
Rate
Rain Water
Providing and fixing on wall face unplasticised Rigid PVC

rain waterpipes conforming to IS : 13592 Type A including
12.41
20 jointing with seal ringconforming to IS : 5382 leaving 10 mm
gap for thermal expansion.(i)Single socketed pipes.
12.41.1 75 mm diameter meter 60.00 95.00 1.39 132.05 7,923.00

12.41.2 110 mm diameter meter 150.00 163.40 1.39 227.13 34,068.90
Providing and fixing on wall face unplasticised - PVC

moulded fittings/accessories for unplasticised Rigid PVC rain
12.42 water pipes conforming toIS : 13592 Type A including
jointing with seal ring conforming to IS :5382 leaving 10 mm
21 gap for thermal expansion
12.42.2 Single pushfit coupler

12.42.2.2 110mm each 8.00 138.85 1.39 193.00 1,544.01
12.42.2.1 75mm each 3.00 101.15 1.39 140.60 421.80
12.42.6 Shoe (Plain)
22
12.42.6.1 75 mm each 3.00 152.25 1.39 211.63 634.88
Providing and fixing on wall face unplasticised - PVC clips of

approved design to unplasticised PVC rain water pipes by
12.43 means of 50x50x50mm hard wood plugs, screwed with M.S.
23 screws of required length including cutting brickwork and fixing
in cement mortar 1:4 (1 cement : 4 coarse sand) and making
good the wall etc. complete.
12.43.1 75mm each 48.00 79.50 1.39 110.51 5,304.24

Total of Rain Water 49,896.83

INDIAN INSTITUTE OF TECHNOLOGY BOMBAYMAIN ENTRANCE DATE : 25.04.2011

1 TOTAL OF ROAD WORK 4,169,407.96
2 TOTAL OF STORM WATER DRAIN 1,003,608.08
3 TOTAL OF COMPOUND WALL 1,379,435.44
TOTAL OF INFRASTRUCTURE WORKS - DSR ITEMS 6,552,451.47
NON-DSR AMOUNT RS.

ITEMS
TOTAL OF INFRASTRUCTURE WORKS - NON-DSR ITEMS -
TOTAL OF INFRASTRUCTURE WORKS - ( DSR ITEMS + 6,552,451.47

NON-DSR ITEMS)
Operative
Rate
Road work
Carriage of material by mechanical transport including loading,

1.1 unloading and stacking with in IIT Campus upto 2KM
1
1.1.1 Lime, moorum, building rubbish cum 50.00 45.13 1.39 62.73 3,136.54
1.1.2 Earth cum 567.00 56.41 1.39 78.41 44,458.41
Demolishing cement concrete manually/ by mechanical

15.2 meansincluding disposal of material within 50 metres lead as
2 per direction ofEngineer - in - charge.
15.2.1 1:3:6 or richer mix cum 5.00 368.45 1.39 512.15 2,560.73
SCHEDULE (BILL) OF QUANTITIES OF INFRA WORK

Operative
Rate
Demolishing R.C.C. work manually/ by mechanical means

including stacking of steel bars and disposal of unserviceable
3 15.3 cum 10.00 537.55 1.39 747.19 7,471.95
material within 50 metres lead as per direction of Engineer - in-
charge.
Demolishing brick work manually / by mechanical means

including stacking of serviceable material and disposal of
15.7
4 unserviceable material within 50 metres lead as per direction of
Engineer-in-charge.
15.7.4 In cement mortar cum 15.00 310.75 1.39 431.94 6,479.14
Demolishing rubble masonry manually / by mechanical means
including stacking of serviceable material and disposal of
15.9
5 unserviceable material within 50 metres lead as per direction of
Engineer-in-charge.
15.9.2 In cement mortar cum 20.00 370.75 1.39 515.34 10,306.85
Earth work in excavation by mechanical means (Hydraulic

excavator) / manual means in foundation trenches or drains
(not exceeding 1.5m in width or 10 sqm on plan) including
2.8
6 dressing of sides and ramming of bottoms, lift upto 1.5m,
including getting out the excavated soil and disposal of surplus
excavated soil as directed, within a lead of 50m.
2.8.1 All kinds of soil cum 1510.00 103.40 1.39 143.73 217,026.26
Preparation and consolidation of sub grade with power road

roller of 8 to12 tonne capacity after excavating earth to an
average of 22.5 cm. depth,dressing to camber and
7 16.1 sqm 3687.00 33.90 1.39 47.12 173,735.13
consolidating with road roller including makinggood the
undulations etc. and re-rolling the sub grade and disposal
ofsurplus earth lead upto 50 metres.

Operative
Rate
Extra for compaction of earth work in embankment under
8 16.2 optimum moisture conditions to give at least 95% of the cum 369.00 4.50 1.39 6.26 2,308.10
maximum dry density(proctor density).
16.3 Supplying and stacking at site.
16.3.1 90 mm to 45 mm size stone aggregate cum 248.00 742.30 1.39 1031.80 255,885.66
9
16.3.2 63 mm to 45 mm size stone aggregate cum 331.00 768.45 1.39 1068.15 353,556.16
16.3.10 Moorum. cum 369.00 421.85 1.39 586.37 216,371.08
Laying spreading and compacting stone aggregate of specified

sizes to WBM specifications including spreading in uniform
thickness, hand picking, rolling with 3 wheeled road / vibratory
10 16.4 roller 8-10 tonne in stages to proper grade and camber, sqm 431.00 192.55 1.39 267.64 115,354.78
applying and brooming requisite type of screening / binding
material to fill up interstices of coarse aggregate watering and
compacting to the required density.
Surface dressing on old surface with hot bitumen of grade A-

90/ S-90 ofapproved quality using 1.95 kg of bitumen per
11 16.27 sqm. with 1.50 cum ofstone chippings 11.2 mm nominal sqm 2612.00 74.05 1.39 102.93 268,851.85
size per 100 sqm of road surfaceincluding consolidation
with road roller of 6 to 8 tonne capacity, etc.complete.
Providing and applying tack coat using hot straight run

bitumen of grade80/ 100 including heating the bitumen,
16.30 spraying the bitumen withmechanically operated spray unit
12 fitted on bitumen boiler, cleaning andpreparing the existing
road surface as per specifications :
16.30.1 On W.B.M. @ 0.75 Kg / sqm. sqm 1229.00 23.90 1.39 33.22 40,828.61
16.30.2 On bituminous surface @ 0.50 Kg / sqm sqm 2612.00 17.15 1.39 23.84 62,266.16

Operative
Rate
2 cm premix carpet surfacing with 2.4cum of stone

chippings 11.2 mmnominal size per 100 sqm and bitumen
emulsion (medium setting min.65% bitumen content)
13 16.34 sqm 3841.00 81.95 1.39 113.91 437,530.23
complying with IS : 8887-1995 using 96kg per cumof chipping
including consolidation with road roller of 6 to 9
tonnecapacity etc. complete .
Providing and laying Bitumen Penetration Macadam with

hard stoneaggregate of quality, size and grading as
specified, with bitumen ofsuitable penetration grade
including required key aggregate as specified,spreading coarse
aggregate with the help of self propelled / tipper
16.36 tailmounted aggregate spreader and applying bitumen by a
pressuredistributor and then spreading key aggregate with
the help of aggregatespreader complete including
14 consolidation with road roller of minimum 8to 10 tonne
capacity to achieve specified values of compaction
andsurface accuracy :
For 50mm compacted thickness using coarse aggregateof

size 50-20 mm graded @ 0.60 cum per 10 sqm
16.36.1 sqm 3841.00 219.75 1.39 305.45 1,173,243.05
keyaggregate of size 12.5 mm graded @ 0.15 cum per
10sqm. With paving asphalt 80/100 @ 50 kg/10 sqm.

Operative
Rate
Providing & laying seal coat of premixed fine aggregate (passing

2.36mm and retained on 180 micron sieve) with bitumen using
128 kg of bitumen of grade 80/100 bitumen per cum of fine
15 16.40 aggregate and 0.60 cum of fine aggregate per 100 sqm of road sqm 3841.00 36.85 1.39 51.22 196,741.78
surface including rolling and finishing with road roller all
complete
25mm Asphalt seal coat
Painting road surface marking with adequate no. of coats to

give uniformfinish with ready mixed road marking paint
16.48 conforming to IS : 164, onbituminous surface in
16 white/yellow shade including cleaning the surfaceof all dirt,
scales, oil, grease and foreign material etc. complete.
16.48.1 New work (Two or more coats). sqm 431.00 58.10 1.39 80.76 34,807.13
Providing and laying 60mm thick factory made cement

concreteinterlocking paver block of M -30 grade made by
block making machinewith strong vibratory compaction and of
17 16.68 approved size and design/ shapelaid in required colour and sqm 540.00 345.35 1.39 480.04 259,219.71
pattern over and including 50mm thickcompacted bed of
fine sand, filling the joints with fine sand etc. allcomplete
as per the direction of Engineer-in-charge.

Operative
Rate
Providing and laying at or near groudn level factory made kerb

stone of M-25 grade cement in position to the required line,
level and curvature jointed with cement mortar 1:3 including
making joints with or without grooves (thickness of joints
18 16.69 except at sharp curve shall not to more than 5mm) including Cum 47.00 4252.70 1.39 5911.25 277,828.89
making the drainage opening wherever required complete etc.
as per the direction of Engineer in charge (length of finished
kerb edging shall be measured for payment). (precast C.C. Kerb
stone shall be approved by engineer - in-charge)

Operative
Rate
Scarifying the existing bituminous road surface to a depth of
19 16.77 50mm anddisposal of scarified material within all lifts and lead sqm 2612.00 2.60 1.39 3.61 9,439.77
upto 1000 metre (bymechanical means).
Total of Road work 4,169,407.96
Storm water Drain work

2.8
Surface dressing of the ground including removing vegetation

and in-equalities not exceeding 15 cm deep and disposal of
21 2.28 100M² 4.80 512.00 1.39 711.68 3,416.06
rubbish, lead upto 50m and lift upto 1.5m
2.28.1 all kinds of soil.
Providing & laying in position cement concrete of specified

4.1 grade excluding the cost of centering and shuttering - All work
22 up to plinth level:
1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggragate
4.1.5 cum 48.00 2791.05 1.39 3879.56 186,218.86
20mm nominal size)

Operative
Rate
Coursed rubble masonry (second sort) with hard stone in
23 7.7.1 foundation and plinth with : cum 152.00 1913.1 1.39 2659.21 404,199.77
cement mortar 1:6 (1 cement : 6 coarse sand)
Formwork for slabs

Centering and shuttering including strutting, propping etc. and
24 5.9.3 removal of form for: sqm 250.00 187.35 1.39 260.42 65,104.13
Suspended floors, roofs, landings, balconies and access
platform.
Providing & laying in position ready mixed concrete

manufactured in fully automatic batching plant and transported
to site of work in transit mixer for a lead up to 10 kms having
continuous agitated mixer, manufactured as per mix design of
specified grade for renforced cement concrete work including
pumping of R.M.C from transit mixer to site of laying, excluding
25 5.37 the cost of centering, shuttering finishing and renforcement cum 37.50 4192.80 1.39 5827.99 218,549.70
including cost of admixtures in recommended proportions as
per IS : 9103 to accelerate/ retard setting of concrete, improve
workability without impairing strength and durability as per
direction of the Engineer - in - charge. M-25 grade Reinforced
cement concrete by using 38kg of cement per cum of concrete.
All works up to plinth level.
13.1 12 mm cement plaster of mix

26
13.1.1 1:4 (1 cement: 4 fine sand) sqm 530.00 77.55 1.39 107.79 57,131.09
Storm drain inlets (600mm x 900mm) Per 30.00
Slotted Drain Inlets (500mm wide) Rmt 0.00
Total of Storm water Drain work 1,003,608.08

Operative
Rate
Compound wall

2.8

Operative
Rate
Excavation work mechanical means (Hydraulic excavator) /

manual means in foundation trenches or drains not exceeding
1.5m in width or 10 sqm on plan including dressing of sides and
2.9
28 ramming of bottoms, lift upto 1.5m, including getting out the
excavated soil and disposal of surplus excavated soil as directed,
within a lead of 50m.
2.9.1 Ordinary rock cum 162.00 162.65 1.39 226.08 36,625.53

Providing and laying in position cement concrete of specified
grade excluding the cost of centering and shuttering - All work
4.1 up to plinth
29 level :
1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggragate

4.1.5 cum 131.00 2791.05 1.39 3879.56 508,222.29
20mm nominal size)
Coursed rubble masonry (second sort) with hard stone
7.7
30 infoundation & plinth with :
7.7.1 Cement mortar 1:6 (1 cement : 6 coarse sand) cum 148.00 1913.1 1.39 2659.21 393,562.93
Pointing on stone work with cement mortar 1:3 (1 cement: 3
13.33
31 fine sand) :
13.33.2 Raised and cut pointing sqm 982.00 112.00 1.39 155.68 152,877.76
Finishing walls with water proofing cement paint of required
13.44 shade :
32
13.44.1 New work (Two or more coats applied @ 3.84 kg/10 sqm). sqm 982.00 30.80 1.39 42.81 42,041.38
Providing and laying 230 mm. thick dry rubble soling in line and
level, hand packed and vertically set, including filling interstices
33 NON DSR with quarry spoils, stone chips, grit etc. finally spreading either Sq m 405.00 264.50 107,122.50
grit or shingle above it as directed, compaction by wooden/
metallic rammers, watering etc. complete.

Operative
Rate
Total of Compound wall 1,379,435.44


1 TOTAL OF SOFT LANDSCAPE 117,953.18
TOTAL OF SOFT LANDSCAPE - DSR ITEMS 117,953.18
NON-DSR AMOUNT RS.

ITEMS
TOTAL OF SOFT LANDSCAPE - NON-DSR ITEMS -
TOTAL OF SOFT LANDSCAPE - ( DSR ITEMS + NON-DSR 117,953.18

ITEMS)
Operative
Rate
Soft Landscape
Clearing jungle including uprooting of rank vegetation, grass,

brushwood, trees and saplings of girth upto 30 cm measured at
1 2.31 100sqm 6.00 263.90 1.39 366.82 2,200.93
a height of1 m above ground level and removal of rubbish upto
a distance of 50m outside the periphery of the area cleared.
Clearing grass and removal of the rubbish upto a distance

2 2.32 100sqm 6.00 135.65 1.39 188.55 1,131.32
of 50 moutside the periphery of the area cleared.
Felling trees of the girth (measured at a height of 1 m above

groundlevel) including cutting of trunks and branches
2.33
removing the rootsand stacking of serviceable material and
3 disposal of unserviceablematerial.
SCHEDULE (BILL) OF QUANTITIES LANDSCAPE WORK

3 Operative
Rate
2.33.2 Beyond 60 cm girth upto and including 120 cm girth each 5.00 359.80 1.39 500.12 2,500.61
2.33.3 Beyond 120 cm girth upto and including 240 cm girth each 10.00 1658.85 1.39 2305.80 23,058.02
Supplying and stacking of good earth at site including royalty
4 23.2 and carriage up to 1 km ( earth measured in stacks will be cum 204.00 144.05 1.39 200.23 40,846.82
reduced by 20% for payment).
Supplying and stacking at site dump manure from approved

23.4 source, including carriage up to 1 km (manure measured in
5 stacks will be reduced by 8% for payment)
23.4.3 Screened through sieve of I. S. designation 4.75mm cum 56.00 97.05 1.39 134.90 7,554.37
6 23.7 Fine dressing the ground 100 sqm 6.00 80.20 1.39 111.48 668.87
Spreading of sludge, dump manure or/and good earth in
7 23.8 required thickness (cost of sludge, dump manure or/ and good cum 204.00 11.60 1.39 16.12 3,289.30
earth to be paid separately)
Mixing earth and sludge or manure in proportion specified or
8 23.9 cum 260.00 7.85 1.39 10.91 2,836.99
directed.
Grassing with 'Doob' grass including watering and maintenance

of the lawn for 30 days or more till the grass forms a thick lawn
23.10
9 free from weeds and fit for mowing including supplying good
earth if needed (the good earth shall be paid for separately)
23.10.3 In rows 5 cm apart in either direction. 100 sqm 6.00 384.85 1.39 534.94 3,209.65

Operative
Rate
Half brick circular tree guard in 50 class designation bricks,

internal diameter 1.25 metre and height 1.2 metre above
ground and 0.20 m below ground bottom two courses laid dry
23.15
10 and top three courses in cement mortar 1:6 (1 cement : 6 fine
sand) and the intermediate courses being in dry honey comb
masonry as per design complete:
23.15.1 With F. P. S. Bricks each 30.00 595.70 1.39 828.02 24,840.69

Edging with bricks laid dry length wise including excavation,
23.19 refilling, consolidating with hand packing and spreading neatly
11 surplus earth within a lead of 50m :
23.19.1.1 F. P. S. Bricks Meter 278.00 15.05 1.39 20.92 5,815.62
Total of Soft Landscape 117,953.18


1 MISCELLANEOUS ITEMS 59,926.24
TOTAL OF MISCELLANEOUS ITEMS - DSR ITEMS 59,926.24
NON-DSR AMOUNT RS.

ITEMS
MISCELLANEOUS ITEMS 3,376,500.00
TOTAL OF MISCELLANEOUS ITEMS - NON-DSR ITEMS 3,376,500.00
TOTAL OF MISCELLANEOUS ITEMS - ( DSR ITEMS + NON- 3,436,426.24

DSR ITEMS)
Operative
Rate
Miscellaneous Items
Providing & fixing UV stabilised fiberglass reinforced plastic

sheetroofing up to any pitch including fixing with polymer
coated 'J' or 'L'hooks, bolts & nuts 8mm dia. G.I
plain/bitumen washers complete butexcluding the cost of
purlins, rafters, trusses etc. The sheets shall bemanufactured
out of 2400 TEX panel rovigs incorporating minimum0.3%
12.47 Ultra-violet stabiliser in resin system under approximately
1 2400psi and hot cured. They shall be of uniform pigmentation
and thicknesswithout air pockets and shall conform to IS
10192 and IS 12866.Thesheets shall be opaque or
translucent, clear or pigmented, textured orsmooth as
specified.
SCHEDULE (BILL) OF QUANTITIES OF MISCELLANEOUS WORK

1 INDIAN INSTITUTE OF TECHNOLOGY BOMBAYMAIN ENTRANCE DATE : 25.04.2011
Operative
Rate
2mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or3"
12.47.1 sqm 33.00 785.35 1.39 1091.64 36,024.00
or 6" ) as specified.
Structural steel work riveted, bolted or welded in built up

sections,trusses and framed work, including cutting,
2 10.2 kg 371.00 46.35 1.39 64.43 23,902.23
hoisting, fixing in positionand applying a priming coat of
approved steel primer all complete:
Providing and fixing S. S. Gate sliding over MS rail at Entrance as

3 NON DSR per design / detail including all fittings & fixtures comlete in all sqm 40.00 40000.00 1,600,000.00
respect
NON DSR Providing and installation of electrically operated Motor for

4 LS 550,000.00
driving SS Gate at Entrance
Supplying and installation of Loose furnitures like Chair, Table,
5 NON DSR Cupboard, File Rack etc for Security cabin as per Architect's sq.ft 2230.00 550.00 1,226,500.00
specification
Total of Miscellaneous Items 3,436,426.24
SCHEDULE (BILL) OF QUANTITIES OF MISCELLANEOUS WORK

INDIAN INSTITUTE OF TECHNOLOGY BOMBAYSECURITY CABINS, MAIN GATE SSADATE : 25.04.2011
S. DSR OPERATIVE
ITEM DESCRIPTION QTY UNIT RATE COST INDEX
NO. 2007 RATE
A B C D E F G H=FXG
SCHEDULES OF RATES - ELECTRICAL PART-1

INTERNAL
COPPER WIRING IN PVC CONDUITS
Point wiring in PVC conduit,with MODULAR type

switch :Wiring for light point/fan point/exhaust fan
point/call bell point with 1.5 sq.mm FR PVC insulated
copper conductor single core cables in surface/recessed
1 1.10
PVC conduit,with modular switch ,modular
plate,,suitable size G.I box and earthing the point with
1.5 sq.mm FR PVC insulated copper conductor single
core cables etc. as required.
A 1.10.1 Group A 75.00 Point 293.00 1.39 407.27
Power Point wiring in PVCconduit(2x4 sq.mm) Wiring

for light point/power point with2x4 sq.mm FR PVC
insulated copper conductor single core cables in
2 1.12 60.00 Metre 97.00 1.39 134.83
surface/recessed PVC conduitalong with 1No 4 sq.mm
FR PVC insulated copper conductor single core cable
for loop earthing as required
Circuit/submain wiring in PVC conduit Wiring for

circuit/submain wiring alongwith earth wire with the
1.14 following sizes of FR PVC insulated copper conductor
3 ,single core cable in surface/ recessed PVC conduit as
required.
1.14.2 2x2.5 sq.mm +1x 2.5 sq.mm earth wire 590.00 Metre 81.00 1.39 112.59
STEEL /PVC CONDUITS, METAL BOXES
SCHEDULE (BILL) OF QUANTITIES ELECTRICAL WORKS 157

Supply & fixing steel conduit: Supply & fixing of following

sizes of steel conduit along with accessories in
4 1.20. surface/recess including painting in case of surface
conduit, or cutting the wall and making good the same in
case of recessed conduit as required.
1.20.2
25mm 35.00 Metre 86.00
Supply & fixingPVC conduit:Supply & fixing of following

sizes of PVC conduit along with accessories in
5 1.21
surface/recess including cutting the wall and making
good the same in case of recessed conduit as required.
1.21.1
A 20mm 450.00 Metre 41.00 1.39 56.99
1.21.2
B 25mm 200.00 Metre 47.00 1.39 65.33
Supply & fixing modular type switch /Socket : Supply &
fixing following modular switch /Socket on the exisitng
6 1.24
modular plate & switch box including connection but
excluding modular plate etc. as required
A 1.24.1 5/6 amps switch 56.00 Each 46.00 1.39 63.94
B 1.24.3 15/16 amps switch 16.00 Each 67.00 1.39 93.13
C 1.24.5 6 pin 15/16 amps socket outlet 16.00 Each 101.00 1.39 140.39
D 1.24.6 Telephone socket outlet 5.00 Each 61.00 1.39 84.79
Supply & fixing modular type elctronic fan regulator :

Supply and fixing stepped type electronic fan regulator
7 1.25 8.00 Each 247.00 1.39 343.33
on the exisitng modular plate switch box including
connection but excluding modular plate etc as required.
Supply & fixing modular type blanking plate : Supply and

fixing modular blanking plate on the exisitng modular
8 1.26 16.00 Each 20.00 1.39 27.80
plate & switch box including connection but excluding
modular plate etc as required.

Supply & fixing modular boxes,base & cover plate:

Supply & fixing following size/modules, GI box along
9 1.27
with modular base and cover plate for modular switches
in recess etc as required.
A 1.27.1 1 or 2 Module(75mmx75 mm) 67.00 Each 88.00 1.39 122.32

B 1.27.2 4 Module(125mmx75 mm) 16.00 Each 113.00 1.39 157.07
Supply & fixing modular base & cover plate: Supply &
10 1.28 fixing following modular base nd cover plate for modular
switches in recess etc as required.
A 1.28.1 1 or 2 Module 67.00 Each 51.00 1.39 70.89

B 1.28.2 4 Module 16.00 Each 71.00 1.39 98.69
Supply & fixing ceiling rose : Supply & fixing 3 pin ,5

11 1.33 amp. Ceiling rose on the exisitng junction box/ wodden 59.00 Each 19.00 1.39 26.41
block including connection etc.as required
ITC Fluorescent fitting directly on surface : Instalaltion

,testing and commissioning of pre wired fluorescent
fitting/ compact fluorescent fitting of all types, complete
12 1.41 with all accessories and tube etc. directly on ceiling/wall 38.00 Each 43.00 1.39 59.77
,including connection with 1.5 sq.mm FR PVC insulated,
copper conductor,single core cable and earthing as
required.
ITC Ceiling fan with cover on fan box: Installation,testing

and commissioning of ceiling fan, including wiring the
down rods of standard length (up to 30cm) with
13 1.45 21.00 Each 68.00 1.39 94.52
1.5sq.mm FR PVC insulated copper conductor, single
core cables including proviidng and fixing phenolic
laminated sheet cover on the fan box etc.as required.

Carriage of fan : Carriage of ceiling fan and

14 1.50 21.00 Each 10.00 1.39 13.90
regulator/exhaust fan from store to site as required.
Numbering of fan/ fittings: Numbering of ceiling
15 1.51 21.00 Each 10.00 1.39 13.90
fan/exhaust fan /fluorscent fittings as required

2. BOARDS AND DB's
BUS TRUNKING AND OVER HEAD BUSBAR SYSTEM
S/F SP MCB DB: Supplying and fixing following way,

single pole and neutral, sheet steel, MCB distribution
board, 240 volts, on surface/ recess, complete with
16 2.31 tinned copper busbar, neutral busbar, earth bar, din bar,
detachable gland plate, interconnections, phosphatized
and powder painted including earthing etc. as required.
(But without MCB/RCCB/Isolator)
A 2.31.6 8 way doble door 1.00 Each 709.00 1.39 985.51
B 2.31.7 12 way doble door 1.00 Each 746.00 1.39 1,036.94
S/F 'B' Series ,SP MCB: Supplying and fixing 5 amps to

32 amps rating,240 volts, 'B' series, miniature circuit
17 2.51 breaker suitable for lighting and other loads of following
poles in the existing MCB DB complete with
connections,testing and commissioning etc as required.
A 2.51.1 Single Pole 16.00 Each 86.00 1.39 119.54

S/F SPN RCCB isolator: Supplying and fixing following
rating, double pole 240 volts, residual current circuit
18 2.56 breaker ( RCCB), having sensitivity current upto 300
milliamperes in the existing MCB DB complete with
A 2.56.1 25 amps 2.00 Each 949.00 1.39 1,319.11
7.LT cables (copper)

Suuplying & errecting pvc armoured cable 2C 4Sqmm

copper conductor continuous 5.48Sqmm (12SWG) GI
19 7.2.2 earth wire complete errected with gland & lugs, on wall / 40.00 Metre 136.00 1.39 189.04
trusses / pole or laid in provided trench / pipe as per
specification no. CB-LT/copper
1. LV/MV Cable Laying
MV Cable laying up to 25 sq.mm in ground: Laying of

one number PVC insulated and PVC sheathed/XLPE
aluminum conductor cable of 1.1KV grade of sizes not
21 1.11 60.00 Metre 85.00 1.39 118.15
exceeding 25 Sq.mm direct in ground including
excavation, sand cushioning, protective covering &
refilling the trench etc as required.
MV Cable laying up to 25 sq.mm on surface: Laying and
fixing of one number PVC insulated and PVC
22 1.11 sheathed/XLPEaluminum conductor cable of 1.1KV 20.00 Metre 31.00 1.39 43.09
grade of sizes not exceeding 25 Sq.mm on surface as
required

MV Cable End Termination & Jointing

S/M LV/MV cable end termination:
Supplying and making end termination with brass

23 4.1 compression gland and aluminium lugs for following size
of PVC insulated and PVC sheathed / XLPE aluminium
conductor cable of 1.1KV grade as required.
4.1.1 2 x 6Sqmm 1.00 Each 69.00 1.39 95.91

4.1.1 2 x 4Sqmm 1.00 Each 69.00 1.39 95.91
TOTAL AS PER CPWD SOR 2007

AMOUNT IN RS.
I=DXH
30,545.25
8,089.80
66,428.10

3,010.00
25,645.50
13,066.00
3,580.64
1,490.08
2,246.24
423.95
2,746.64
444.80

8,195.44
2,513.12
4,749.63
1,579.04
1,558.19
2,271.26
1,984.92

291.90
291.90

985.51
1,036.94
1,912.64
2,638.22

7,561.60
9,618.80
7,089.00
861.80

95.91
95.91
213,048.73

M.S.
S. OPERATIVE
PWD ITEM DESCRIPTION QTY UNIT RATE COST INDEX
NO. RATE
DSR NO
A B C D E F G H=FXG
Telephone wiring
Supplying & errecting telephone cable 1 pair with 0.5mm
1 1.10.1 dia laid in provided pvc casing / conduit as per 75.00 Metre 9.00 1.39 12.51
specification no. WG-TW
Supplying , errecting & commissioing junction box
2 1.11.12 1.00 Each 553.00 1.39 768.67
suitable for 10 pairs as per specification no. WG-TW
Supplying , errecting & commissioing crone module of 10
3 1.11.20 1.00 Each 339.00 1.39 471.21
pairs as per specification no. WG-TW
LAN cabling
Supplying & installing UTP networking CAT 6 cable

4 1.12.1 suitable for LAN / WAN computer networking as per 75.00 Metre 33.00 1.39 45.87
specification no. WG-COC/NC
Supplying & installing & testing UTP connector (RJ45)
5 1.14.1 6.00 Each 20.00 1.39 27.80
as per specification no. WG-NAS/UTPC
Supplying & fixing toolless information outlet (ethernet)
6 1.14.2 flush / surface type in position as per specification no. 6.00 Each 521.00 1.39 724.19
WG-NAS/IO
Inverter
Supplying, installing, testing & commissioning of 600VA
7 3.6.1 digital pure sine wave inverter single phase 230V, 50Hz 1.00 Each 7,049.00 1.39 9,798.11
complete as per specification no. AP-INV
Supplying & errecting 12 Volt / 150AH tubular battery
8 3.8.2 with battery terminal wire , duly charged complete with 30 1.00 Each 12,351.00 1.39 17,167.89
months warrenty complete.
Indoor fittings (FG-IDF)
SCHEDULE (BILL) OF QUANTITIESELECTRICAL WORKS 171

Supplying & errecting 1 x 28 W T5 energy efficient retrofit

/ standalone flurescent tubelight fitting (EETLF) box type
complete with electronic ballast & lamp holder duly wired
9 2.2.38 ready to use for 230 Volts , 50Hz. Single phase AC 26.00 Each 932.00 1.39 1,295.48
supply to IS: 10322 as per quality requirement & errected
on varnished wooden block with flexible wire twin core
24/0,2mm & marking sr.no. & date of erection.
Supplying & errecting T5 28 Watt energy efficient

10 2.1.11 26.00 Each 124.00 1.39 172.36
flerescent tube
Supplying & errecting circular type recessed / surface
down lighter with reflector & glass cover suitable for CFL
11 2.2.21 1 x 9 to 18 Watts with circular stainless steel ring 12.00 Each 766.00 1.39 1,064.74
including electronic ballst & holder duly fixed in false
ceiling as per specification no FG-IDF / DL1
Supplying & errecting compact flerescent lamp 5/7/8/9/11

12 2.1.38 12.00 Each 87.00 1.39 120.93
Watt , 230Volts to be used with provided ballast.
Supplying and erecting Ceiling fan of 900mm. Sweep

13 2.6.2 complete erected in position as per specification no. FG- 4.00 Each 1,260.00 1.39 1,751.40
FN/CF
FN/CF
Providing and erecting air circulator 450mm .sweep

oscillating type, wall mounting 1440 RPM without speed
regulator, overheat protection unit, totally enclosed, flame
15 2.6.6 proof motor suitable for 230/250 Volts single phase, 50 3.00 Each 4,255.00 1.39 5,914.45
cycles A.C. Supply with one metre of 3 core lead wire
and with moisture proof treatment to winding and with "E"
class insulation and marking Sr. No. and date of erection.

Supply and erecting fresh air cum Exhaust fan of light

duty 250 V A.C. 50 cycles 225mm, 1400 RPM metallic
16 2.6.15 body, plastic blades, wire mesh, duly erected in an 10.00 Each 1,122.00 1.39 1,559.58
approved manner and marking Sr. No. and date of
erection.
TOTAL AS PER MAHARASHTRA GOVT P.W.D.

AMOUNT IN RS.
I=DXH
938.25
768.67
471.21
3,440.25
166.80
4,345.14
9,798.11
17,167.89

33,682.48
4,481.36
12,776.88
1,451.16
7,005.60
7,005.60
17,743.35

15,595.80
136,838.55

SR. AMOUNT RS.

ITEM DESCRIPTION
NO.
1 DSR ITEMS 213,048.73
MSPWD ITEMS 136,838.55
TOTAL OF DSR ITEMS & MSPWD ITEMS 349,887.28
SR. AMOUNT RS.

ITEM DESCRIPTION
NO.
TOTAL OF NON-DSR ITEMS -
TOTAL OF MISCELLANEOUS ITEMS - ( DSR ITEMS + MSPWD 349,887.28

ITEMS + NON-DSR ITEMS)
S. COST OPERATIVE
CODE ITEM DESCRIPTION QTY UNIT RATE
NO. INDEX RATE
A B C D E F G H=FXG
DSR 2007 ITEM AS PER DSR 2007
DSR
COPPER WIRING IN PVC CONDUITS
2007
Point wiring in PVC conduit,with MODULAR type
switch :Wiring for light point/fan point/exhaust fan
point/call bell point with 1.5 sq.mm FR PVC insulated
copper conductor single core cables in surface/recessed
1.10
1 PVC conduit,with modular switch ,modular
plate,,suitable size G.I box and earthing the point with
1.5 sq.mm FR PVC insulated copper conductor single
core cables etc. as required.
SCHEDULE (BILL) OF QUANTITIES ELECTRICAL WORKS, SECURITY CABIN

1 INDIAN INSTITUTE OF TECHNOLOGY BOMBAYMAIN ENTRANCE DATE : 25.04.2011
1.10.1 Group A 75.00 Point 293.00 1.39 407.27

Power Point wiring in PVCconduit(2x4 sq.mm) Wiring
for light point/power point with2x4 sq.mm FR PVC
insulated copper conductor single core cables in
2 1.12 60.00 Metre 97.00 1.39 134.83
surface/recessed PVC conduitalong with 1No 4 sq.mm
FR PVC insulated copper conductor single core cable
for loop earthing as required
Circuit/submain wiring in PVC conduit Wiring for
circuit/submain wiring alongwith earth wire with the
1.14 following sizes of FR PVC insulated copper conductor
3 ,single core cable in surface/ recessed PVC conduit as
required.
1.14.2 2x2.5 sq.mm +1x 2.5 sq.mm earth wire 590.00 Metre 81.00 1.39 112.59
STEEL /PVC CONDUITS, METAL BOXES
Supply & fixing steel conduit: Supply & fixing of following
sizes of steel conduit along with accessories in
1.20. surface/recess including painting in case of surface
4 conduit, or cutting the wall and making good the same in
case of recessed conduit as required.
1.20.2
25mm 35.00 Metre 86.00
Supply & fixingPVC conduit:Supply & fixing of following

sizes of PVC conduit along with accessories in
1.21
surface/recess including cutting the wall and making
5 good the same in case of recessed conduit as required.
1.21.1
20mm 450.00 Metre 41.00 1.39 56.99
1.21.2
25mm 200.00 Metre 47.00 1.39 65.33

Supply & fixing modular type switch /Socket : Supply &

fixing following modular switch /Socket on the exisitng
1.24
modular plate & switch box including connection but
excluding modular plate etc. as required
6
1.24.1 5/6 amps switch 56.00 Each 46.00 1.39 63.94
1.24.3 15/16 amps switch 16.00 Each 67.00 1.39 93.13
1.24.5 6 pin 15/16 amps socket outlet 16.00 Each 101.00 1.39 140.39
1.24.6 Telephone socket outlet 5.00 Each 61.00 1.39 84.79
Supply & fixing modular type elctronic fan regulator :

Supply and fixing stepped type electronic fan regulator
7 1.25 8.00 Each 247.00 1.39 343.33
on the exisitng modular plate switch box including
connection but excluding modular plate etc as required.
Supply & fixing modular type blanking plate : Supply and

fixing modular blanking plate on the exisitng modular
8 1.26 16.00 Each 20.00 1.39 27.80
plate & switch box including connection but excluding
modular plate etc as required.
Supply & fixing modular boxes,base & cover plate:
Supply & fixing following size/modules, GI box along
1.27
with modular base and cover plate for modular switches
9 in recess etc as required.
1.27.1 1 or 2 Module(75mmx75 mm) 67.00 Each 88.00 1.39 122.32
1.27.2 4 Module(125mmx75 mm) 16.00 Each 113.00 1.39 157.07
Supply & fixing modular base & cover plate: Supply &
1.28 fixing following modular base nd cover plate for modular
10 switches in recess etc as required.
1.28.1 1 or 2 Module 67.00 Each 51.00 1.39 70.89
1.28.2 4 Module 16.00 Each 71.00 1.39 98.69

Supply & fixing ceiling rose : Supply & fixing 3 pin ,5

11 1.33 amp. Ceiling rose on the exisitng junction box/ wodden 59.00 Each 19.00 1.39 26.41
block including connection etc.as required
ITC Fluorescent fitting directly on surface : Instalaltion
,testing and commissioning of pre wired fluorescent
fitting/ compact fluorescent fitting of all types, complete
12 1.41 with all accessories and tube etc. directly on ceiling/wall 38.00 Each 43.00 1.39 59.77
,including connection with 1.5 sq.mm FR PVC insulated,
copper conductor,single core cable and earthing as
required.
ITC Ceiling fan with cover on fan box: Installation,testing

and commissioning of ceiling fan, including wiring the
down rods of standard length (up to 30cm) with
13 1.45 21.00 Each 68.00 1.39 94.52
1.5sq.mm FR PVC insulated copper conductor, single
core cables including proviidng and fixing phenolic
laminated sheet cover on the fan box etc.as required.
Carriage of fan : Carriage of ceiling fan and

14 1.50 21.00 Each 10.00 1.39 13.90
regulator/exhaust fan from store to site as required.
Numbering of fan/ fittings: Numbering of ceiling
15 1.51 21.00 Each 10.00 1.39 13.90
fan/exhaust fan /fluorscent fittings as required
2. BOARDS AND DB's
BUS TRUNKING AND OVER HEAD BUSBAR SYSTEM

S/F SP MCB DB: Supplying and fixing following way,

single pole and neutral, sheet steel, MCB distribution
board, 240 volts, on surface/ recess, complete with
2.31 tinned copper busbar, neutral busbar, earth bar, din bar,
16 detachable gland plate, interconnections, phosphatized
and powder painted including earthing etc. as required.
(But without MCB/RCCB/Isolator)
2.31.6 8 way doble door 1.00 Each 709.00 1.39 985.51
2.31.7 12 way doble door 1.00 Each 746.00 1.39 1,036.94
S/F 'B' Series ,SP MCB: Supplying and fixing 5 amps to

32 amps rating,240 volts, 'B' series, miniature circuit
2.51 breaker suitable for lighting and other loads of following
17 poles in the existing MCB DB complete with
2.51.1 Single Pole 16.00 Each 86.00 1.39 119.54
S/F SPN RCCB isolator: Supplying and fixing following

rating, double pole 240 volts, residual current circuit
2.56 breaker ( RCCB), having sensitivity current upto 300
18 milliamperes in the existing MCB DB complete with
2.56.1 25 amps 2.00 Each 949.00 1.39 1,319.11

7.LT cables (copper)


1. LV/MV Cable Laying
MV Cable laying up to 25 sq.mm in ground: Laying of
one number PVC insulated and PVC sheathed/XLPE
aluminum conductor cable of 1.1KV grade of sizes not
21 1.11 60.00 Metre 85.00 1.39 118.15
exceeding 25 Sq.mm direct in ground including
excavation, sand cushioning, protective covering &
refilling the trench etc as required.
MV Cable laying up to 25 sq.mm on surface: Laying and
fixing of one number PVC insulated and PVC
22 1.11 sheathed/XLPEaluminum conductor cable of 1.1KV 20.00 Metre 31.00 1.39 43.09
grade of sizes not exceeding 25 Sq.mm on surface as
required
MV Cable End Termination & Jointing
S/M LV/MV cable end termination:
Supplying and making end termination with brass

4.1 compression gland and aluminium lugs for following size
23 of PVC insulated and PVC sheathed / XLPE aluminium
conductor cable of 1.1KV grade as required.
4.1.1 2 x 6Sqmm 1.00 Each 69.00 1.39 95.91

4.1.1 2 x 4Sqmm 1.00 Each 69.00 1.39 95.91

ITEM AS PER MAHARSHTRA GOVT. PWD

M.S.
S. PWD COST OPERATIVE
ITEM DESCRIPTION QTY UNIT RATE
NO. DSR INDEX RATE
NO
A B C D E F G H=FXG
Telephone wiring
Supplying & errecting telephone cable 1 pair with 0.5mm
1 1.10.1 dia laid in provided pvc casing / conduit as per 75.00 Metre 9.00 1.39 12.51
specification, no.
Supplying errecting
WG-TW & commissioing junction box
2 1.11.12 1.00 Each 553.00 1.39 768.67
suitable for 10 pairs as per specification no. WG-TW
Supplying , errecting & commissioing crone module of 10
3 1.11.20 1.00 Each 339.00 1.39 471.21
pairs as per specification no. WG-TW
LAN cabling
Supplying & installing UTP networking CAT 6 cable
4 1.12.1 suitable for LAN / WAN computer networking as per 75.00 Metre 33.00 1.39 45.87
specification
Supplying & no.
installing
WG-COC/NC
& testing UTP connector (RJ45)
5 1.14.1 6.00 Each 20.00 1.39 27.80
Supplying & fixing no.
as per specification toolless information outlet (ethernet)
WG-NAS/UTPC
6 1.14.2 flush / surface type in position as per specification no. 6.00 Each 521.00 1.39 724.19
WG-NAS/IO
Inverter
Supplying, installing, testing & commissioning of 600VA
7 3.6.1 digital pure sine wave inverter single phase 230V, 50Hz 1.00 Each 7,049.00 1.39 9,798.11
Supplying & errecting 12 Volt / 150AH tubular battery
complete as per specification no. AP-INV
8 3.8.2 with battery& terminal
Supplying errectingwire
1 x ,28
duly
W T5charged
energycomplete
efficient with
retrofit
30 1.00 Each 12,351.00 1.39 17,167.89
/months
standalone
warrenty
flurescent
complete.
tubelight fitting (EETLF) box type
Indoor fittings (FG-IDF)
complete with electronic ballast & lamp holder duly wired
9 2.2.38 ready to use for 230 Volts , 50Hz. Single phase AC 26.00 Each 932.00 1.39 1,295.48
supply to IS:
Supplying &&10322
errecting
errecting
as per
circular
T5
quality
28typerequirement
Watt
recessed
energy &/errected
efficient
surface
10 2.1.11 26.00 Each 124.00 1.39 172.36
down lighter
on varnished
flerescent with
tubewooden block with flexible wire twin coreCFL
reflector & glass cover suitable for
11 2.2.21 1 x 9 to &18
24/0,2mm Watts sr.no.
marking with &circular
date of stainless
erection. steel ring 12.00 Each 766.00 1.39 1,064.74
including electronic
Supplying & errectingballst
compact& holder
flerescent
dulylamp
fixed5/7/8/9/11
in false
12 2.1.38 12.00 Each 87.00 1.39 120.93
ceiling
Watt
Supplying
, 230Volts
as per
andspecification
to
erecting
be usedCeiling
with
no FG-IDF
provided
fan of
/ DL1
ballast.
900mm. Sweep
FN/CF
FN/CF

Providing and erecting air circulator 450mm .sweep
oscillating type, wall mounting 1440 RPM without speed
regulator, overheat protection unit, totally enclosed, flame
Supply and erecting fresh air cum Exhaust fan of light
15 2.6.6 proof motor suitable for 230/250 Volts single phase, 50 3.00 Each 4,255.00 1.39 5,914.45
duty 250 V A.C. 50 cycles 225mm, 1400 RPM metallic
cycles A.C. Supply with one metre of 3 core lead wire
16 2.6.15 body, plastic blades, wire mesh, duly erected in an 10.00 Each 1,122.00 1.39 1,559.58
and with moisture proof treatment to winding and with "E"
approved
TOTAL PERmanner and marking Sr. No. and date of
class AS MAHARASHTRA
insulation GOVT
and marking Sr.P.W.D.
No. and date of erection.
erection.

AMOUNT IN RS.
I=DXH

30,545.25
8,089.80
66,428.10
3,010.00
25,645.50
13,066.00

3,580.64
1,490.08
2,246.24
423.95
2,746.64
444.80
8,195.44
2,513.12
4,749.63
1,579.04

1,558.19
2,271.26
1,984.92
291.90
291.90

985.51
1,036.94
1,912.64
2,638.22
7,561.60

9,618.80
7,089.00
861.80
95.91
95.91
213,048.73

AMOUNT IN RS.
I=DXH
938.25
768.67
471.21
3,440.25
166.80
4,345.14
9,798.11
17,167.89
33,682.48
4,481.36
12,776.88
1,451.16
7,005.60
7,005.60

17,743.35
15,595.80
136,838.55

SR. AMOUNT RS.

ITEM DESCRIPTION
NO.
1 DSR ITEMS 50,735.00
MSPWD ITEMS 928,436.60
TOTAL OF DSR ITEMS & MSPWD ITEMS 979,171.60
SR. AMOUNT RS.

ITEM DESCRIPTION
NO.
NON-DSR ITEM 5,610,000.00
TOTAL OF NON-DSR ITEMS 5,610,000.00
TOTAL OF MISCELLANEOUS ITEMS - ( DSR ITEMS + MSPWD 6,589,171.60

ITEMS + NON-DSR ITEMS)
S. COST OPERATIVE
CODE ITEM DESCRIPTION QTY UNIT RATE
NO. INDEX RATE
A B C D E F G H=FXG
DSR 2007 ITEM AS PER DSR 2007
Prewired MCB DB
S/F prewired MCB DB: Supplying and installation &
testing & commissioing of 4 way (4+4) , TPN , vertical
1791
1 type , prewired MCB DB with extended loose wire box ,
double door
2.43.5 4 way vertical double door 1.00 Each 5,830.00 1.39 8,103.70
MCB, RCCB, MCB DB's
2 1722 63 Amps rating , 4 pole RCCB 100mA / 300mA 1.00 Each 1,218.00 1.39 1,693.02
6 Amp to 32 Amp rating TP MCB 'C' series 10KA
3 1709 4.00 Each 1,218.00 1.39 1,693.02
breaking capacity
Steel tubular pole & strut
SCHEDULE (BILL) OF QUANTITIES AREA LIGHTING

Erection of metallic street light standard upto 8.5m in

CC.: Erection of metallic street light standard pole of
length exceeding 6.5 metres but not exceeding 8.5
metres in cement concrete 1:3:6 (1 cement: 3 coarse
4 6.9 20.00 Each 1,229.00 1.39 1,708.31
sand : 6 graded stone aggregate 40mm nominal size)
foundation with cement concrete collar of size 0.4m dia x
0.5m height to accommodate the looping type cable end
box including excavation and refilling etc. as required.
ITEM AS PER MAHARSHTRA GOVT. PWD
S. M.S. PWD COST OPERATIVE

ITEM DESCRIPTION QTY UNIT RATE
NO. DSR NO INDEX RATE
A B C D E F G H=FXG
Suplying & errecting pvc armoured cable 4C 25Sqmm

aluminium conductor continuous 5.48Sqmm (12SWG) GI
specification no. CB-LT/aluminium

specification no. CB-LT/CU


specification no. CB-LT/CU
Hot deep galvanised poles & high mast (HM)
Providing & erecting 9.0Mtr high galvanised octagonal
pole with bottom of 155mm A/F, top 70mm A/F sword
4 8.3.7 20.00 Each 22,571.00 1.39 31,373.69
type doule arm bracket on provided foundation as per
specification no.OH-PL/PSC
Bracket for outdoor fittings
Supply and erecting street light brackets for single fittings
made from 40mm dia B class GI pipes 1.0m in length
5 2.5.5 20.00 Each 599.00 1.39 832.61
along with pole cap of 300mm length 100mm dia duly
welded as per specification no FG-BKT/BPC
Street light box
Supply & erecting water tight terminal box of cast iron of
6 7.8.7 size 150x100x100mm complete on pole as per 20.00 Each 467.00 1.39 649.13
specification no. CB-SB
Out door fittings (FG-ODF)
Supply and erecting street light metal halide lamp fitting
7 2.3.22 250W on provided bracket as per specification no. FG- 20.00 Each 2,990.00 1.39 4,156.10
ODF/GSL
Lamp ( FG-LP)
Supply and erecting H.P.S.V Lamp threaded type 230V,
8 2.1.27 20.00 Each 574.00 1.39 797.86
250W (SON-T type)
Accessories
Supply and erecting condensor for M.V. lamp 250 W, 230
9 2.4.3 20.00 Each 255.00 1.39 354.45
V as per specification No. FG-Fg/AS7

Supply and erecting electronic ignitor suitable for Metal

hallide Lamp 70/150/250/400 Watts (Intergral/non-
10 2.4.6 20.00 Each 313.00 1.39 435.07
integral type luminaries) as per specification No. FG-
FG/AS6
TOTAL AS PER MAHARASHTRA GOVT P.W.D.
11 NON DSR Providing & fixing Bollard 102.00 55,000.00
TOTAL AS NON-DSR ITEM

AMOUNT IN RS.
I=DXH
8,103.70
1,693.02
6,772.08

34,166.20
50735.00
AMOUNT IN RS.
I=DXH
12,176.40
86,736.00

57,546.00
627,473.80
16,652.20
12,982.60
83,122.00
15,957.20
7,089.00

8,701.40
928,436.60
5,610,000.00
5,610,000.00

Ac Boq

Uploaded by

Copyright:

Available Formats

Ac Boq

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ac Boq

Uploaded by

Copyright:

Available Formats

INDIAN INSTITUTE OF TECHNOLOGY BOMBAY REFURBISHMENT OF P.C. SAXENA AUDITORIUMINSIDE I.I.T.

I SUB STRUCTURE WORKS 0

III PLUMBING WORK 0

IV FIRE ALARM SYSTEM & PUBLIC ADDRESS SYSTEM 0

TENDER DOCUMENT BILL OF QUANTITIES SIGNATURE AND SEAL OF TENDERER

SR. NO. ITEM DESCRIPTION AMOUNT (RS.)

I SUB STRUCTURE WORKS

TOTAL OF EXCAVATION & EARTH WORKS 0

TOTAL OF PLAIN CEMENT CONCRETE 0

TOTAL OF REINFORCED CEMENT CONCRETE 0

TOTAL OF SUB STRUCTURE WORKS 0

TOTAL OF STEEL & ROOFING WORK 0

TOTAL OF DEMOLITION WORK 0

TOTAL OF BRICK WORK 0

TOTAL OF PLASTERING / PUNNING WORK 0

TOTAL OF FALSE CEILING WORK 0

TOTAL OF FLOORING, SKIRTING & DADO WORK 0

TOTAL OF PAINTING WORK 0

TOTAL OF DOOR WORKS 0

TOTAL OF WOOD WORKS (PARTITION & PANELLING) 0

TOTAL OF ALUMINUM WINDOW WORK 0

TOTAL OF MISCELLANEOUS WORKS 0

TOTAL OF FINISHING WORK 0

TENDER DOCUMENT BILL OF QUANTITIES SIGNATURE AND SEAL OF TENDERER

III PLUMBING WORK

TOTAL OF SANITARYWARES & CP APPURTENANCES 0

TOTAL OF WATER SUPPLY SYSTEM 0

TOTAL OF INTERNAL DRAINAGE SYSTEM 0

TOTAL OF PLUMBING WORK 0

IV FIRE ALARM SYSTEM & PUBLIC ADDRESS SYSTEM

TOTAL OF FIRE ALARM SYSTEM 0

TOTAL OF CABLES & ACCESSORIES 0

TOTAL FOR POINT WIRING IN PVC CONDUIT, TELEPHONE WIRING, T.V

TOTAL FOR UPS SYSTEM 0

TOTAL OF DISTRIBUTION BOARDS 0

TOTAL FOR L.T.CABLES, END JOINTS 0

TOTAL OF EARTHING SYSTEM 0

TOTAL OF ELECTRICAL WORK WORK 0

GRAND TOTAL OF (I+II+III+IV+V+VI) 0

TENDER DOCUMENT BILL OF QUANTITIES SIGNATURE AND SEAL OF TENDERER

GENERAL IMPORTANT NOTES APPLICABLE TO THIS CONTRACT

g) Scaffolding to be provided for execution , shall be of Independent Scaffold Conforming to IS 2750

TENDER DOCUMENT BILL OF QUANTITIES - 4 SIGNATURE AND SEAL OF TENDERER

TENDER DOCUMENT BILL OF QUANTITIES - 5 SIGNATURE AND SEAL OF TENDERER

Sr. No. Description Unit Qty

2.1 All type of Soil Cum 40.00

4 Supplying and spreading pesticides CHLORPYRIPHOS or other chemical

5.1 230 mm thick with contractor supply of stone Sqm. 20.00

TENDER DOCUMENT BILL OF QUANTITIES - 6 SIGNATURE AND SEAL OF TENDERER

Sr. No. Description Unit Qty

B PLAIN CEMENT CONCRETE

(Note :- 1) Prior approval of Engineer in charge for the supplier of RMC to be

6.1 Cum 12.00

TOTAL OF PLAIN CEMENT CONCRETE

C REINFORCED CEMENT CONCRETE

TENDER DOCUMENT BILL OF QUANTITIES - 7 SIGNATURE AND SEAL OF TENDERER

Sr. No. Description Unit Qty

Reinforced cement concrete of M-20 grade of design mix concrete conforming to