SCHEDULE OF QUANTITIES FOR HVAC WORKS:

SI Description of Item
Air-conditioning works
1.a Supply, Installation, Testing and Commissioning of accessories for the AHU ceiling suspended
AHU as under:

- Modular AHU panels with GI sheet of 0.60 mm thick for both inner & outer casing with
25 mm insulation sand witched in between. The outer panel shall have pre coating for
corrosion resistance as also to provide a very good finish.
- Blower section with forward curved centrifugal fan with TEFC motor (IP 55 and Class F
insulation).
- Drain section with 1.2mm SS drain pan.
- Coil section with 4/6 row chilled water coil, Slimseal BF valves at inlet/ outlet, drain and
purge connections.
a. Flexible connection the outlet.
b. AHU sub panel with isolator and starter (Star/ Delta) with lockable OFF pushbutton.
c. Fresh air cowl with screen and damper.
e. Power wiring with 3 C x 16 sqmm. PVC armoured copper cable with end terminations
and two runs of 6 SWG copper earth rods (approx length - 20 M)
f. Inlet and outlet isolating valves of 65 mm dia:
g. 3-way mixing valve with all connections and control wiring
h. Pressure gauges and thermometers at inlet and outlet

Ceiling suspended AHU, 30 mm SP:

a. 6 TR CSU, 2400 CFM, 30 mm SP for Kapindra machine room
b. 3.2 TR FCU, 1200 CFM, 30 mm SP for the other areas

NOTE: This shall only include the accessories for the mentioned AHU capacity. The owner
shall be providing the AHU

2
Supply, Laying, Pressure testing and insulating of chilled water piping, complete with fittings,
supports and insulation. Insulation of 50 mm thick TF quality thermocole with 22 G
Aluminium cladding. Insulations shall be as under/as per IS 1239, Mild Steel heavy (Class C)
class pipe:

a. 65 mm dia:
b. 50 mm dia:
 Drain piping from the AHU with PVC piping and insulated as required:

- 32 mm dia:
- 32 mm dia drain valve:

3.a
Supply and laying of galvanized sheet steel ducting with class VIII quality of zinc coating, complete
with anchor fasteners and MS supports, angle bracings as required, nut, bolt & gasket etc
etc.
a. 24 G ducting:
b. 22 G ducting:
c. 20 G ducting:

3.b Supply and laying of aluminium spiral ducting, complete with anchor fasteners and MS supports, angle
bracings as required, nut, bolt & gasket etc

22 G ducting:
20 G ducting:

Acceptable makes: GI sheets: Jindal/ Nippon/ SAIL/JS or equivalent

3.c Supply and fixing of volume control dampers

24G
22G

4 Supply and installation of powder coated Al. Supply air grills and return air outlets:
a. Supply air grille with damper
b. Return air grille w/o damper.
c. Supply air diffuser with damper (circular/square)
d. Return air diffuser without damper (circular/square)
Acceptable makes: Air Master/ Air Breeze/System Air/AAF or equivalent.

5 Supply and installation of fusible link type fire damper

6 Supply and laying of thermal insulation of ducting with 15 mm thick nitrile rubber, laminated with
Aluminium foil

Acceptable makes: Armaflex, Armacell, A-flex, k-flex or equivalent

7 Supplying and installation of acoustic insulation of ducting with 19 mm thick armasound or equivalent
material.

Acceptable makes: Armasound or equivalent

8 Charges for air balancing the system as per specification

TOTAL OF 1 TO 8

NOTE: All the above rates must be quoted inclusive of all applicable taxes, transport, scaffolding, and all n

Note:
Offer valid for 15days.
FCU,CSU,AHU Ducting related works not Considered
Electrical work done by Electrical Contractor
GST will Extra applicable
Any additional items/Qty required will be charged Extra.
WORKS:

Qty Unit Rate Amount

1 no. 152000 152000

1 no. 58000 58000

2.5 M 1830 4575

30 M 1580 47400
30 M 380 11400
2 nos. 2800 5600

50 sqM. 1000 50000

10 sqM. 1160 11600
5 sqM. 1420 7100

1 sqM 1400 1400

1 sqM 1500 1500

1 sqM. 7900 3950

1 sqM. 7600 3800

RO sqM. 10325
RO sqM. 8500
1 sqM. 13500 13500
1.5 sqM. 12000 18000

0.5 sqM. 9500 4750

20 sqM. 870 17400

 15 sqM. 1290 19350

included times 28000 28000

459,325.00

t, scaffolding, and all necessary accessories.

1.a

2
3.a

3.b

3.c

3d,

4
5

10

SI
Air-conditioning works
1.a
AIR-CONDITIONING WORKS
Supply, Installation, Testing and Commissioning of AHU ceiling suspended AHU as under:

- Modular AHU panels with GI sheet of 0.60 mm thick for both inner & outer casing with 25 mm insulation
sand witched in between. The outer panel shall have pre coating for corrosion resistance as also to provide a
very good finish.

- Blower section with forward curved centrifugal fan with TEFC motor (IP 55 and Class F insulation).
- Drain section with 1.2mm SS drain pan.
- Coil section with 6 row chilled water coil, Slimseal BF valves at inlet/ outlet, drain and purge connections.

a. Flexible connection the outlet.

b. AHU sub panel with isolator and starter (Star/ Delta) with lockable OFF pushbutton.
c. Fresh air cowl with screen and damper.
d. Masonry Blocks of 150 mm height placed below the AHUs.
e. Power wiring with 3 C x 16 sqmm. PVC armoured copper cable with end terminations and two runs of 6
SWG copper earth rods (approx length - 20 M)
f. Inlet and outlet isolating valves of 65 mm dia:
g. 3-way mixing valve with all connections and control wiring
h. Pressure gauges and thermometers at inlet and outlet
i. Dehumidification heater banks to be provided for RH control within range of 40-60% RH (for the 12 TR and
14 TR units)
NOTE: The AHU will be provided by the builder. Only the above mentioned accessories are to be provided by
the successful bidder

Ceiling suspended AHU, 30 mm SP:

a. 12 TR CSU, 4800 CFM, 110 mm SP with pre and microvee filter for Kapindra lab. This will be connected to
terminal hepa filter.
b. 3.2 TR CSU, 1200 CFM for the other areas

NOTE: The above AHU will be connected to terminal fan filter unit for HEPA filtration in the lab

Supply, Laying, Pressure testing and insulating of chilled water piping, complete with fittings, supports and
insulation. Insulation of 50 mm thick TF quality thermocole with 22 G Aluminium cladding. Insulations shall be
as under/as per IS 1239, Mild Steel heavy (Class C) class pipe:

a. 65 mm dia:
b. 50 mm dia:

Drain piping from the AHU with PVC piping and insulated as required:

- 50 mm dia:
- 32 mm dia:
- 50 mm dia drain valve:
- 32 mm dia drain valve:

Supply and laying of aluminium ducting, complete with anchor fasteners and MS supports, angle bracings as required,
nut, bolt & gasket etc

22 G ducting:
20 G ducting:

Supply and laying of galvanized sheet steel ducting with class VIII quality of zinc coating, complete with anchor fasteners
and MS supports, angle bracings as required, nut, bolt & gasket etc
etc.
a. 24 G ducting:
b. 22 G ducting:
c. 20 G ducting:

Supply and laying of aluminium spiral ducting, complete with anchor fasteners and MS supports, angle bracings as
required, nut, bolt & gasket etc
22 G ducting:
20 G ducting:

Acceptable makes: GI sheets: Jindal/ Nippon/ SAIL/JS or equivalent

Supply and fixing of volume control dampers

20G
22G

Supply and installation of powder coated Al. Supply air grills and return air outlets:
a. Supply air grille with damper
b. Return air grille w/o damper.
c. Supply air diffuser with damper (circular/square)
d. Return air diffuser without damper (circular/square)
e. Ceiling suspended laminar flow SS plenum for labs comprising as standard feature with HEPA filter
efficiency not less than 99.97% at 0.3 Microns (Factory DOP tested). with air flow at approx. 90-100 Fpm
velocity. Each HEPA filter - 2 ft x 2 ft. This is to be mounted only for the ceiling suspended units 12 TR for the
labs

f. Ceiling suspended fan filter unit of SS construction complete with independent fan with HEPA filter
efficiency not less than 99.97% at 0.3 Microns (Factory DOP tested). with air flow at approx. 90-100 Fpm
velocity. Each HEPA filter to take care of 750 CFM capacity. These units are only for the development lab and
MPCVD labs
Fan filter units, 750 CFM capacity
Acceptable makes: Air Master/ Air Breeze/System Air/AAF or equivalent.
g. Floor/wall mounted fan filter unit of SS construction complete with independent fan with HEPA filter
efficiency not less than 99.97% at 0.3 Microns (Factory DOP tested). with air flow at approx. 90-100 Fpm
velocity. Each HEPA filter to take care of 750 CFM capacity. These units are only for the development lab and
MPCVD labs
Fan filter units, 750 CFM capacity

Supply and installation of fusible link type fire damper

Supply and laying of thermal insulation of ducting with 15 mm thick nitrile rubber, laminated with Aluminium
foil

Acceptable makes: Armaflex, Armacell, A-flex, k-flex or equivalent

Supplying and installation of acoustic insulation of ducting with 19 mm thick armasound or equivalent
material.

Acceptable makes: Armasound or equivalent

Supply and installation of acoustic insulation for the walls of the AHU room with 25 mm thick armasound or
equivalent material.

Charges for air balancing the system as per specification

SITC of chilled water compact cassette unit (1 TR capacity) complete with all fittings and accessories for the
UPS and server room with a 24 hour auto timer

TOTAL OF HVAC SYSTEM

Description of Item
Air-conditioning works
Supply, Installation, Testing and Commissioning of accessories for the AHU ceiling suspended AHU as under:

- Modular AHU panels with GI sheet of 0.60 mm thick for both inner & outer casing with 25 mm insulation
sand witched in between. The outer panel shall have pre coating for corrosion resistance as also to provide a
very good finish.

- Blower section with forward curved centrifugal fan with TEFC motor (IP 55 and Class F insulation).
- Drain section with 1.2mm SS drain pan.
- Coil section with 4/6 row chilled water coil, Slimseal BF valves at inlet/ outlet, drain and purge
connections.
a. Flexible connection the outlet.
b. AHU sub panel with isolator and starter (Star/ Delta) with lockable OFF pushbutton.
c. Fresh air cowl with screen and damper.
e. Power wiring with 3 C x 16 sqmm. PVC armoured copper cable with end terminations and two runs of 6
SWG copper earth rods (approx length - 20 M)
f. Inlet and outlet isolating valves of 65 mm dia:
g. 3-way mixing valve with all connections and control wiring
h. Pressure gauges and thermometers at inlet and outlet

Ceiling suspended AHU, 30 mm SP:

a. 6 TR CSU, 2400 CFM, 30 mm SP for Kapindra machine room

b. 3.2 TR FCU, 1200 CFM, 30 mm SP for the other areas

NOTE: This shall only include the accessories for the mentioned AHU capacity. The owner shall be providing
the AHU
Valve Packages with necessary bolts, nuts and washers for 6 TR CSU and 3.0TR FCU
TOTAL OF HVAC SYSTEM

Note:
Offer valid for 15days.
Scaffolding, Civil Works , Duct Paint, Duct Torpolin sheet done by Customer
FCU,CSU,AHU Ducting related works not Considered
Electrical work done by Electrical Contractor
GST will Extra applicable
Any additional items/Qty required will be charged Extra.

Note:
Offer valid for 15days.
Scaffolding, Civil Works , Duct Paint, Duct Torpolin sheet done by Customer
FCU,CSU,AHU Valve Package Not Consider
Electrical work done by Electrical Contractor
GST will Extra applicable
Any additional items/Qty required will be charged Extra.
1.00 no. 342,500.00 342,500.00
1.00 no. 86,000.00 86,000.00

3.00 M 1,850.00 5,550.00

30.00 M 1,600.00 48,000.00

3.00 M 425.00 1,275.00

30.00 M 380.00 11,400.00
5.00 no. 2,200.00 11,000.00
2.00 nos. 2,800.00 5,600.00

30.00 sqM 1,450.00 43,500.00

20.00 sqM 1,585.00 31,700.00

40.00 sqM. 1,000.00 40,000.00

10.00 sqM. 1,165.00 11,650.00
5.00 sqM. 1,425.00 7,125.00

5.00 sqM 1,650.00 8,250.00

5.00 sqM 1,850.00 9,250.00

1.00 sqM. 7,950.00 7,950.00

1.00 sqM. 7,650.00 7,650.00

1.00 sqM. 10,325.00 10,325.00

2.00 sqM. 8,500.00 17,000.00
1.00 sqM. 13,500.00 13,500.00
2.00 sqM. 12,000.00 24,000.00
1.00 nos. 40,000.00 40,000.00

6.00 nos. 87,500.00 525,000.00

1.00 NOS 95,000.00 95,000.00

0.50 sqM. 9,500.00 4,750.00

25.00 sqM. 870.00 21,750.00

20.00 sqM. 1,300.00 26,000.00

3.00 sqM. 2,100.00 6,300.00

1.00 times 28,000.00 28,000.00

2.00 sets 54,000.00 108,000.00

1,598,025.00

Qty Unit Rate Amount

1 no. 175,000.00 175,000.00

1 no.

1 Lot 58,000.00 58,000.00

233,000.00
 List of Approved makes for HVAC works
Sl.No Name of Material Approved Makes
1 Motor Siemens/ Kirloskar/ NGEF/ ABB.
2 Starters L & T/Siemens/Honewell
3 Exhaust Fans Almonard/Kruger/Nadi/Nicotra/Lau
Voltas/ Blue Star/ Carrier/ System Air
(Saiver)/ ETA/ Cary Aire/ Edge
4 AHUs Tech/Luftek
5 Cables(power) Finolex/Polycab/Havells
6 Cables (control) Finolex.
7 Grills/ Diffusers Air Master/ Air Breeze/Cosmic
8 G I Sheets Jindal/ Nippon/ SAIL.
9 Wall mounted fans Almonard, Nicotra, Havells.
10 Nitrile rubber A-flex/k-flex

Philips, Seimens or equivalent. Should be

11 UV lamp easily maintained and replaceable in India.
12 VFD Starter Panel Siemens/L&T/ABB/Danfoss
13 3 way mixing valve Honeywell