AVAILABLE CONFIGURATIONS / FIGURE NUMBERS

M&H AWWA C500 STANDARD DOUBLE DISC GATE VALVES

M&H AWWA Double Disc Parallel Seat IBBM Gate Valves

Meet or Exceed the requirements of AWWA C500

Size Range Water Working Hydrostatic Shell

Pressure psi Test psi
2” – 12” 200 400
14” – 48” 150 300

Size Figure
Available End Connections Range Number.
Flanged Ends (NRS) 2”-48” F-5070
Flanged Ends (OS&Y) 14”-36” F-5072
Mechanical Joint 2”-48” F-5065
*Mechanical Joint (Cutting End) 4”-12” F-5067
*Tyton Ends (For D.I. / C900) 4”-12” F-5080
*Flange End X Mechanical Joint 4”-48” F-5066
*Flange End X Tyton End (For D.I. / C900) 4”-12” F-5080
*Push-on (For PVC / SDR) 2”-10” F-5085
*Tapping Valve 4”-24” F-5093

*Contact Factory for availability and lead times

Note: Call Factory for Special Applications
42” & 48”Drawings Available on Request
Customer Drawings Available on Request

Accessories:
Floor stands
Limit Switches
Open Gearing
Needle & Slot (Navy) Indicators
Electric Motors
2” Square Operating Nuts
Chain wheels
“T” Handles
Stem Guides
Indicator Posts
By-pass Valves
Enclosed Gearing (Grease Case)
Barrel Indicators
Tracks, Rollers, & Scrapers for valves 14” or larger installed horizontally in line
Hand wheels
Extension Stems
Floor boxes

September 1, 2012 / Double Disc / DD1

M&H DOUBLE DISC GATE VALVES
Description and Advantages: rocker bearing on the iron hooks, letting wedges adjust
M&H AWWA Gate Valves are designed primarily for to varying positions of the gates in closing. The long
flow control of water in underground pipe lines. They side is used in closing the valve and the short side in
equal or exceed the requirements established by opening it.
standards of the American Water Works Association
and conform to Federal Specifications WW-V-58B, Low Torque Thrust Bearing: Valves 4”-12” are fitted
Type II, Class I. below the stem collar with an exclusive Low Torque
Thrust Bearing which provides high load capacity and
M&H AWWA Gate Valves are specifically designed low friction. This bearing reduces operating torque up
for heavy pressure service. Neck, flanges, and bell are to 50% yet seals perfectly for repacking under
made extra heavy to withstand pipe strain and possible pressure.
shifting. Body, cover, gates, and stem are built for
extra strength, with clean and simple internal Gates and Gate Rings: Gates 3” and smaller are bronze.
construction, to assure long service and low Gates 4” and larger are high strength cast iron with
maintenance. bronze gate rings rolled into machined and dovetailed
grooves under pressure to make gate and ring one
Operation of the Valve: inseparable unit. After fitting, gate rings are accurately
Turning the stem releases the wedging pressure on the machined.
gates allowing them to move away from there seats
before starting upward travel. Further turning of the Case rings: Bronze case rings are screwed into place
stem raises the gates into the fully opened position. and machined. They can be removed and replaced if
necessary.
When closing the valve, the gates move freely
downward without friction, to a position opposite their Packing: O-Ring packing is standard on all non-rising
seats. stem gate valves. Rising stem and geared valves are
furnished with conventional packing.
As the gates approach the bottom of the valve, the iron
hooks come into contact with stops which prevent Operating Nut and Handwheel: All valves except
further downward movement of the hooks. The bronze flanged valves and outside screw and yoke valves are
wedges riding on these hooks spread the gates apart supplied with 2” square operating nuts of high strength
and force them against their seats. cast iron unless otherwise specified. Flanged valves
and outside screw and yoke valves are supplied with
Construction: handwheels of high strength cast iron unless otherwise
Body: Cast iron, bronze mounted. Sturdy proportions specified. Direction of opening is indicated by arrow
provide protection against damage. cast on operating nut skirt or on the rim of the
handwheel.
Stem: Manganese bronze of high tensile and torsional
strength, with accurate, perfectly machined threads. Yoke: Yokes for outside screw and yoke valves are of
Ample diameters assure smooth valve movements. rugged cast iron. Careful machining assures accurate
stem alignment.
Stem Nut: Solid bronze. Independent of hooks, gates,
and wedges. Stem or stem nut will not bind or spring Accessories: Valves may be fitted with and large
out of line, as can happen when stem nut is attached to number of accessories: cylinders, electric motor
wedges. operators, gearing, bypasses, etc.

Wedges: Independent, solid bronze, 2”-3” valves have Rollers, Tracks, and Scrapers: Recommended for 14”
integral hook and wedge. 4”-8” have independent and larger diameter valves carry weight of the gates for
solid bronze wedges placed loosely in iron hooks, and valves installed in a horizontal or vertical line.
are free to adjust to various positions of the gates. In
10” and larger valves, each wedge has one long and NOTE: All valves open to the left (counter clockwise)
one short surface. The bottom of each wedge forms a unless otherwise specified.

September 1, 2012 / Double Disc / DD17

SAMPLE GATE VALVE SPECIFICATION
M&H DOUBLE DISC GATE VALVES
Gate Valves:
Valves shall be manufactured in accordance with Stems:
AWWA Standard C500-93. Valves 12” and smaller Stems shall be in full conformance with AWWA
shall be designed for 200 psi water working pressure Specs. Sizes 14”-36” bronze ASTM B584 with 80,000
and 150 psi for valves 14”-48” inclusive. Valves shall tensile strength, and cast integral stem collar. 42” and
have (MJ, Flanged or as indicated on plans) ends and 48” shall be type 304 stainless steel.
shall have clear waterway equal to the full nominal
diameter of the valve. Valves shall be double disc Stem Nuts:
parallel seat type with (non-rising, rising) stems, Stem nuts shall be made of solid bronze independent of
opening by turning (left, right) and provided with (2” hooks, gates and wedges. No pins will be allowed to
square nuts, handwheel), with arrow cast in metal to retain gates to stem nut.
indicate direction of opening.
Gates and Gate Rings:
Manufacturer of 2-48” gate valves must have the full Gates shall be high strength cast iron, sturdily
range of valves in both NRS and OS&Y styles. proportioned without pockets on backs. Cam surfaces
shall open to bottom. Gate rings shall be rolled into
Each manufacturer shall provide certification that they dovetailed grooves under pressure to make one
have manufactured 2”-48” valves for a minimum of ten inseparable unit. The gate ring face shall be machined
years. to a smooth finish.

Each valve shall have manufacturer’s name, pressure Case Rings:

rating and year in which manufactured cast on body. Bronze case rings shall be screwed into place and the
Prior to shipment from the factory each valve shall be contact face machined to a smooth finish. Use of
hydrostatically shell tested at a pressure of 400 psig in screws, rivets of other means of retention will not be
sized 12” and smaller and 300 psig in sizes 14” and acceptable.
larger. In addition each valve shall be hydrostatically
seat tested at a pressure of 200 psig in sizes 12” and Valves 14” and Larger:
smaller and 150 psig in sizes 14” and larger. Valves Valves installed with stem horizontal shall be equipped
shall be AWWA valves as supplied by the M&H Valve with bronze rollers, tracks, and scrapers.
Company, Anniston, Alabama.
Bypasses:
Stuffing Boxes: Bypasses shall be provided on 16” and larger valves
Stuffing Boxes shall be “O” ring seal type with two o- where indicated and mounted directly to valve body
rings located in stem above thrust collar in valves with cast iron flanged connections. Bypass valves
without gearing. Sizes 14” through 48” there shall be a shall be resilient seated AWWA and ULFM approved
bronze bushing meeting ASTM B584. for sizes through 36” and integral double disc type
bypass valves for 42” and 48” sizes.
Bolts and Nuts:
Body and cover bolts and nuts shall meet specification Gearing:
ASTM A307 rust proofed. Enclosed spur or bevel gearing with extended type gear
cases will be provided where indicated on plans. Side
Wedging: cover plates will be provided to completely enclose
Valves will be bottom wedging type with two part stem and stuffing box. Manufacturer must be able to
floating wedge contact. The wedge and hook shall be supply open and enclosed gearing as standard.
separate castings and not a one piece casting in valves
4”-36”. In valves 42” and 48” the hooks and wedges
shall be one piece design with the outside of the wedge
area covered with a bronze shoe. No side wedging will
be acceptable.

September 1, 2012 / Double Disc / DD18

ORDERING INFORMATION
M&H DOUBLE DISC GATE VALVES

When placing orders or making inquiries, please furnish the following information. This information
will enable us to answer your questions, prepare quotations, and fill your order promptly. Lack of
essential information is almost sure to cause delays. Use figure number wherever possible to identify
product wanted.

1. Quantity 8. Operating nut or handwheel: All flanged

valves and all rising stem valves with outside
2. Size screw and yoke are furnished with handwheels
unless otherwise specified. Other valves are
3. Working pressure: Refer to tables of furnished with a 2-inch square operating nut
pressure ratings unless otherwise specified.

4. End type or types: Gate valves are 9. Stuffing box: Whether conventional or O-
furnished with many end types ring. Unless otherwise specified, we regularly
furnish NRS valves with O-ring packing; other
4A. Flanged valves: Furnished with ANSI 125 valves are regularly furnished with conventional
pound Standard flanges with bolt holes stuffing box packing.
straddling center lines.
10. Indicator posts and valves: State depth of
4B. Mechanical Joint valves: Normally trench (distance from ground line to bottom of
furnished with standardized mechanical joints the pipe line); size and shape of operating nut, if
with plain rubber gaskets. Cutting-in type other than standard. For valves already in place,
mechanical joints also available for use in state whether valve is equipped with a flange for
existing cast iron pipe lines. post support; if so, give flange dimensions, and
distance from centerline of valve to top of
5. Direction of opening: Must be specified. flange.
Open left (counterclockwise); or open right
(clockwise). 11. By-pass valves: State location, whether
manually operated by-pass will have handwheel
6. Type of stem: State whether non-rising stem or operating nut, and any special instructions
or rising stem with outside screw and yoke. necessary.

7. Installation position: Indicate position in 12. Parts: Always order parts by number.
which valve will be installed (vertically,
horizontally, or otherwise).

September 1, 2012 / Double Disc / DD19

SPECIFICATIONS / AVAILABLE CONFIGURATIONS / STYLE NUMBERS
M&H LIST 16 EXTRA HEAVY PRESSUE DOUBLE DISK GATE VALVES

M&H List 16 Double Disc Parallel Seat IBBM Gate Valves

Meet or Exceed the requirements of AWWA C500

Size Range Water Working Hydrostatic Shell

Pressure psi Test psi
4” – 12” 250 500
24” – 30” 225 450

Size
Available End Connections Range Figure No.
Flanged Ends (NRS) 4”-48” F-5300
Flanged Ends (OS&Y) 14”-48” F-5305

Notes:
Flanges are faced and drilled to ANSI Class 250 Standard
Call Factory for Special Applications
Contact Factory for availability, lead time, dimensional drawings on 36” through 48”
Contact Factory for Flanges drilled to ANSI Class 125lb standard

Accessories:
Floor stands
Limit Switches
Open Gearing
Needle & Slot (Navy) Indicators
Electric Motors
2” Square Operating Nuts
Chain wheels
“T” Handles
Stem Guides
Indicator Posts
By-pass Valves
Enclosed Gearing (Grease Case)
Barrel Indicators
Tracks, Rollers, & Scrapers for valves 14” or larger installed horizontally in line
Hand wheels
Extension Stems
Floor boxes

September 1, 2012 / C500 Double Disc / DD15