Ace T Aldehyde

ACETALDEHYDE
Acetaldehyde (ethanal), CH3CHO [75-07-0], was observed in 1774 by Scheele during reaction of black
manganese dioxide and sulfuric acid with alcohol. Its constitution was explained in 1835by Liebig who prepared
pure acetaldehyde by oxidation of ethanol with chromic acid and designated this product “aldehyde,” a
contraction of the term “alcohol dehydrogenatus.” Acetaldehyde is a mobile, low-boiling, highly flammable liquid
with a pungent odor. Because of its high chemical reactivity, acetaldehyde is an important intermediate in the
production of acetic acid, acetic anhydride, ethyl acetate, peracetic acid, butanol, 2- ethylhexanol, pentaerythritol,
chlorinated acetaldehydes (chloral), glyoxal, alkyl amines, pyridines, and other chemicals. The first commercial
application was the production of acetone via acetic acid between 1914 and 1918 in Germany (Wacker-Chemie
and Hoechst) and in Canada (Shawinigan). Acetaldehyde is an intermediate in the metabolism of plant and
animal organisms, in which it can be detected in small amounts. Larger amounts of acetaldehyde interfere with
biological processes. As an intermediate in alcoholic fermentation processes it is present in small amounts in all
alcoholic beverages, such as beer, wine, and spirits. Acetaldehyde also has been detected in plant juices and
essential oils, roasted coffee, and tobacco smoke. Commercial production processes include dehydrogenation
or oxidation of ethanol, addition of water to acetylene, partial oxidation of hydrocarbons, and direct oxidation of
ethylene. In the 1970s, the world capacity of this last process, the Wacker-Hoechst direct oxidation, increased
to over 2×106 t/a. However, the importance of acetaldehyde as an organic intermediate is now steadily
decreasing, because new processes for some acetaldehyde derivatives have been developed, such as the oxo
process for butanol and 2-ethylhexanol and the Monsanto process for acetic acid. In the future, new processes
for acetic anhydride (Halcon, Eastman, Hoechst), for vinyl acetate (Halcon), and for alkyl amines (from ethanol)
will diminish the use of acetaldehyde as a starting material.
Production of Acetaldehyde
A.) Veba-Chemie Process
Acetaldehyde production by the Veba-Chemie

process
a) Air compressor; b) Heat recovery system; c) Reactor;
d) Cooler; e) Waste-gas scrubber; f) Washing-alcohol and
return pump; g) Cooler; h) Acetaldehyde rectification
Ethanol is mixed with air and passed over a silver catalyst at 500 – 650 ◦C (c). The temperature depends on the
ratio of alcohol to air and the flow rate of the gas through the catalyst. Alcohol conversion varies between 50 and
70% and the yield is between 97 and 99% depending on the reaction conditions. Acetaldehyde and unconverted
alcohol are removed from thewaste gas bywashing with cold alcohol (e) and separated by fractional distillation
(h); after concentration the alcohol returns to the reactor. Heat formed in the reaction is utilized for steam
production using a waste-heat recovery system immediately after the reaction zone. The waste gas consists
mainly of nitrogen, hydrogen, methane, carbon monoxide and carbon dioxide; it is burned as lean gas with low
calorific value in steam generators. Small amounts of acetic acid are obtained as a byproduct.
B.) One Stage Process
Figure 2. One-stage process

a) Reactor; b) Separating vessel; c) Cooler; d) Scrubber; e) Crude aldehyde tank; f) Cycle-gas compressor; g) Light-ends
distillation; h) Condensers; i) Purification column; l) Product cooler; m) Regeneration
Ethylene and oxygen are charged into the lower part of the reaction tower (a); the catalyst is circulated via the
separating vessel (b) by the airlift principle and thoroughly mixed with the gas. Reaction conditions are about
130 ◦C and 400 kPa. An acetaldehyde – water vapor mixture, together with unconverted gas, is withdrawn from
the separating vessel; from this mixture the reaction products are separated by cooling (c) and washing with
water (d); unconverted gas is returned to the reactor. A small portion is discharged from the cycle gas as exhaust
gas to prevent accumulation of inert gases in the cycle gas; these inert gases are either introduced as
contamination of the feed gas (nitrogen, inert hydrocarbons) or formed as byproducts (carbon dioxide). A partial
stream of catalyst is heated to 160 ◦C (m) to decompose byproducts that have accumulated in the catalyst. Crude
acetaldehyde obtained duringwashing of the reaction products is distilled in two stages. The first stage (g) is an
extractive distillation with water in which lights ends having lower boiling points than acetaldehyde
(chloromethane, chloroethane, and carbon dioxide) are separated at the top, while water and higher-boiling
byproducts, such as acetic acid, crotonaldehyde, or chlorinated acetaldehydes, are withdrawn together with
acetaldehyde at the bottom. In the second column (i) acetaldehyde is purified by fractional distillation.
C.) Two Stage Process
Figure 3. Two-stage process

a) Reactor; b) Flash tower; c) Catalyst pump; d) Oxidation reactor; e) Exhaust-air separator; f) Crude-aldehyde column;
g) Process-water tank; h) Crude-aldehyde container; i) Exhaust-air scrubber; k) Exhaust-gas scrubber; l) Light-ends
distillation;
m) Condensers; n) Heater; o) Purification column; p) Cooler; q) Pumps; r) Regeneration
Tubular reactors (a), (d) are used for both “reaction” and “oxidation”. The gases react almost completely in the
presence of the catalyst. Reaction of ethylene takes place at 105– 110 ◦C and 900 – 1000 kPa. Catalyst solution
containing is then expanded in a flash tower (b) by reducing the pressure to atmospheric level. An acetaldehyde
– water vapor mixture distills overhead while catalyst is sent via the pump (c) to the oxidation reactor (d), in which
it reacts with oxygen at about 1000 kPa. As oxidation and reaction are carried out separately, no high-purity
starting gas is required. Generally, air is used instead of oxygen. Oxygen conversion is almost complete; the
exhaust air from (e) can be used as inert gas for plant use. The oxidized catalyst solution separated from exhaust
air in the separator (e) is reused for the reaction with ethylene in (a). Acetaldehyde – water vapor mixture from
the flash tower (b) is preconcentrated in column (f) to 60 – 90% acetaldehyde by utilizing the heat of reaction.
Process water discharged at the bottom of (f) is returned to the flash tower to maintain a constant catalyst
concentration. A portion of the processwater is used for scrubbing exhaust air (nitrogen from the “oxidation”) in
(i) and exhaust gas (inert gas from the “reaction”) in (k) free of acetaldehyde. Scrubber water then flows to the
crude aldehyde column (f). A two-stage distillation of the crude acetaldehyde follows. In the first stage (l),
lowboiling substances, such as chloromethane, chloroethane and carbon dioxide, are separated. In the second
stage (o), water and higher-boiling byproducts, such as chlorinated acetaldehydes and acetic acid, are removed
from acetaldehyde,and the latter is obtained in pure form overhead. Chlorinated acetaldehydes become
concentrated within the column as medium-boiling substances and are discharged laterally. From this mixture,
monochloroacetaldehyde can be obtained as the hemihydrate. Residual byproducts can be returned to the
catalyst for oxidative decomposition. This oxidative self-purification is supported by thermal treatment of a partial
stream of catalyst at about 160 – 165 ◦C (regeneration,r). When gas mixtures obtained in naphtha cracking
processes are used as rawmaterial, conventional towers are used as reactors instead of coiled pipes; So far,
these processes have not been developed industrially. Such mixtures contain 30 – 40% ethylene in addition to
inert hydrocarbons and hydrogen.

Ace T Aldehyde

Uploaded by

Copyright:

Available Formats

Ace T Aldehyde

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ace T Aldehyde

Uploaded by

Copyright:

Available Formats

ACETALDEHYDE

A.) Veba-Chemie Process

Acetaldehyde production by the Veba-Chemie

B.) One Stage Process

Figure 2. One-stage process

Figure 3. Two-stage process

You might also like