Variable Speed Units For Pumped Storage Power Plants: Page 1 of 9
Variable Speed Units For Pumped Storage Power Plants: Page 1 of 9
Variable Speed Units For Pumped Storage Power Plants: Page 1 of 9
K. Scherer
1. Introduction
Pumped storage power plants are an essential part of complex electric grids because
they provide high additional capacity at extreme short start up time. Stability of grids
becomes more and more a challenge due to higher utilisation of installed capacities
for power generation but also due to an increasing number of wind power plants. For
quite some time pumped storage power plants mainly were erected in mountainous
regions, where natural inflow also was used to a large extent in addition to pumping
up water. To meet tomorrow's requirements, however, pumped storage power plants
are also necessary in areas, where a high head design cannot be applied for
topographical reasons. In such pumped storage power plants the nominal head
typically is in the range of 200 m to 400 m only, whereas the typical range for rated
output is 200 to 350 MW per unit. Francis pump turbines and bi-directional motor-
generators are more or less a standard for such types of power plants.
Pumped storage power plants as described above usually are characterized by high
variations of the actual hydraulic head, which lead to sub-optimal unit efficiencies in
turbine operation and varying power consumption in pump mode. Furthermore, due
to certain restrictions in the hydraulic design the utilization of the available head in
the reservoir is limited. In the past dual-speed units were developed to overcome this
disadvantage, using a special arrangement of the stator winding of the motor-
generator to shift between two numbers of poles, therefore changing the
synchronous speed. This solution, of course, is not very flexible and its application is
limited to certain numerical proportions of the two synchronous speeds.
A new technology for pumped power schemes in the medium head range is the use
of variable speed units, in which the operating speed can be varied in a certain range
of the nominal "synchronous speed". Such a variable speed is made possible by
using double-fed motor-generators which are basically operating as asynchronous
units by feeding low frequency alternating current into to excitation winding instead of
DC current.
Key advantages of this technology are:
• More flexibility in operation
• Higher efficiency in a wide range of part load turbine operation
• A wide range of controllable and optimized power consumption in pump operation
13th Intern. Seminar on Hydropower Plants - Copyright Institute for Waterpower and Pumps – Vienna 2004
Page 2 of 9
• Additional and faster features for grid control (shifting the actual speed in addition
to conventional control of active and reactive power and frequency)
• Better utilization of the reservoir because higher variations of the water level can
be allowed, therefore optimization of civil work
• Additional contribution to grid stability because of high moment of inertia of rotating
masses
Since units of higher output normally are "tailor-made", the actual design, of course,
depends on actual requirements and contract specifications, design tradition and
experience of the manufacturer and it is the result of an ongoing optimization
process. However, the basic design concept of conventional synchronous generators
of medium and bigger size has not changed since decades. Usually the stator
winding is a three phase winding, embedded in a laminated stator core. The
magnetic field is then generated by salient poles which are fixed to the rotor using
different concepts. Usually dove-tail designs or T-heads are used to optimize the
mechanical system with regard to mechanical stresses during normal operation as
well as during runaway-speed, which is the worst case and creates maximum stress
levels in the rotating system. These poles consist of laminated sheets in between two
solid pole end plates each (thoroughly pressed by bolts) and pole coils which are
fixed to the pole bodies. Electrically, all coils of a rotor are connected in series and
fed by direct current. The source of necessary excitation energy either is a rotating
AC exciter machine with rotating rectifiers or a static excitation unit which feeds the
pole coils via slip rings.
It is quite obvious that in case of bi-directional operation additional care has to be
taken for designing thrust and guide bearings and the ventilation system. Axial fans,
for example, cannot be used in such an operation mode.
The operating synchronous speed itself is the result of an optimization process on
the turbine side and is one of the key input parameters given to the generator design
engineer.
f
nsyn = 60 x 1
p
nsyn ….. synchronous speed (rpm)
f1 …….. grid frequency
p …….. number of pole pairs
13th Intern. Seminar on Hydropower Plants - Copyright Institute for Waterpower and Pumps – Vienna 2004
Page 3 of 9
embedded in slots of a stator core. By feeding this winding with three phase
alternating current of variable frequency the resulting speed of the unit can vary from
values below to above synchronous speed.
( f ± f2 )
nact = 60 x 1
p
nact ….. actual speed (rpm)
f1 …….. grid frequency
f2 …….. frequency of the rotor circuit (converter output)
p …….. number of pole pairs
IEC 60034 claims that generators can be operated with 10% unbalanced load.
Conventional generators with salient poles are designed with a damper winding,
which is capable of carrying the inverse sequence current in case of unbalanced
load. The frequency of the inverse sequence current in the damper winding is twice
13th Intern. Seminar on Hydropower Plants - Copyright Institute for Waterpower and Pumps – Vienna 2004
Page 4 of 9
the frequency of the grid. Due to additional losses and the temperature rise of the
generator unbalanced load is limited.
A variable speed motor-generator cannot be equipped with a damper winding
because of the three phase power supply to the rotor winding. Hence the three phase
rotor winding and the cycloconverter have to carry the inverse sequence current. The
frequency of the inverse sequence current in the rotor winding varies with the speed
of the rotor.
Extensive simulations not only have shown that variable speed motor-generators can
be operated with unsymmetrical loads but also have provided additional information
for the design of rotor windings and protection systems. Due to the higher
frequencies in the rotor current additional losses will occur in the rotor winding, in the
core and in the converter. On the other hand, these additional frequencies can be
used by sophisticated protection systems to detect unbalanced load conditions.
Normally, slip rings are designed for DC rotor currents up to approximately 1000 A
and rotor voltages of a few hundred Volts. In case of variable speed double-fed
asynchronous generators a set of slip rings for three-phase power supply to the rotor
winding must be provided.
A design example is given in Fig. 1, which shows a slip ring for rated current of 9000
A and a nominal voltage of 4 kV. High load and the very specific environment in the
presence of carbon dust require special consideration of proper ventilation and
sufficient clearances.
Rotor leads for three-phase AC current ask for special attention because of eddy
currents and stray losses. Slightest non-symmetrical heating of the shaft due to eddy
currents would eventually create distortions in the shaft and create severe problems
with vibrations. Fig. 2 shows a result of a detailed analysis using Finite Element
calculations.
13th Intern. Seminar on Hydropower Plants - Copyright Institute for Waterpower and Pumps – Vienna 2004
Page 5 of 9
New manufacturing methods, special devices and modified test procedures are
required to achieve all targets simultaneously.
An innovative solution to support the entire overhang of the rotor winding is the use
of non-magnetic forged retaining rings – a design feature well-known for high-speed
13th Intern. Seminar on Hydropower Plants - Copyright Institute for Waterpower and Pumps – Vienna 2004
Page 6 of 9
turbo generators but new as an application for hydro generators. The supporting
system consists of shrunk-on outer retaining rings, inner support rings and a very
special design of spacers in between the winding bars. This lavish system enables
necessary support, proper cooling and protection of the high voltage insulation
against mechanical damage. It also minimizes relative movements between
laminated rotor body and the rotor winding. One of the most critical tasks is the
forging and machining process of the rings because of the material specification and
actual dimensions combined with high requirements regarding accuracy.
Fig. 5a: Resonance curve at 100 kN excitation Fig. 5b: Resonance curve at 100 kN excitation
at the turbine runner at the generator rotor
13th Intern. Seminar on Hydropower Plants - Copyright Institute for Waterpower and Pumps – Vienna 2004
Page 7 of 9
13th Intern. Seminar on Hydropower Plants - Copyright Institute for Waterpower and Pumps – Vienna 2004
Page 8 of 9
As a part of the optimization process of the hydraulic system one synchronous unit
and one variable speed unit are fed by a common penstock each. Fig. 6 is a very
simplified basic diagram which shows the electric system for feeding the rotor
windings. Fig. 7a and 7b are sectional views of the motor-generators to indicate the
key differences in design and size. Clearly to be seen the impressive arrangement for
the slip rings in the variable speed unit (Fig. 7a) and the shorter dimensions of the
stator core of the synchronous unit (Fig. 7b).
Fig. 7a: Sectional view to the variable speed Fig. 7b: Sectional view to the synchronous
motor-generator in GOLDISTHAL motor-generator in GOLDISTHAL
Most of the work for development and basic design including theoretical
investigations and simulations for the motor-generators was performed at VA TECH
HYDRO's generator departments. Due to the complexity of the design work close
interaction and co-ordination with consortium partners were necessary and regular
design reviews were held. Additionally, a very successful cooperation with the
Technical Universities in Graz, Austria, and Dresden, Germany, took place in some
specific areas.
On-site erection work for the motor-generators at GOLDISTHAL started in late 2001,
by June 2004 the last of the four units was successfully commissioned and handed
over for commercial operation.
5. Conclusion
Providing peak power in large and complex electrical grids becomes more and more
important along with highly advanced grid control strategies. It is quite a complex
task and even a challenge to modern grid management to keep such systems in
stable and safe operation at minimized costs. Variable speed technology for pumped
storage power plants gives new opportunities regarding grid control, efficiency,
stability and optimized utilization of new or existing reservoirs.
Variation of power consumption in a wide range during pump operation can now be
combined with significantly improved turbine efficiencies in part load conditions and
new possibilities for grid control. By "shifting" the operational speed in very short time
an additional kind of dynamic intervention to conventional control mechanism is
available for frequency, active and reactive power.
13th Intern. Seminar on Hydropower Plants - Copyright Institute for Waterpower and Pumps – Vienna 2004
Page 9 of 9
Literature
[1] J.M. Merino, A. Lopéz, Effizienterer und flexiblerer Betrieb von Wasserkraft-
werken mit Varspeed-Generatoren, ABB Technik 3 (1996), 33 – 38
[2] E. Kopf, S. Brausewetter, M. Giese, F. Moser, Optimized control strategies for
variable speed machines, 22nd IAHR Symposium on Hydraulic Machinery and
Systems, Stockholm (2004)
[3] W. von Nesse-Lapp, E. Dimter, Advantages of variable speed pump-turbines,
22nd IAHR Symposium on Hydraulic Machinery and Systems,Stockholm (2004)
[4] U. Voigt, Die drehzahlgeregelten 265-MW-Pumpspeichersätze des
PSW Goldisthal, VGB-ETG-Konferenz (2004)
[5] E. Kita, T. Kuwabara, Y. Kanda, Development of the world's largest 400 MW
adjustable speed pumped storage unit, IEEE Summer Meeting, Hydroelectric
Subcommittee Meeting (1994)
[6] E. Kita, A. Bando, T. Kuwabara, 400-MW Adjustable-Speed Pumped-Storage
Hydraulic Power Plant, Hitachi Review Vol. 44 (1995), 56 – 62
Author
13th Intern. Seminar on Hydropower Plants - Copyright Institute for Waterpower and Pumps – Vienna 2004