Omega Acb Catalogue PDF

Safeguard your systems
from electrical turbulence
UW1- 0 8 S
3 POLE
I n: 800A U imp: 12kV
Ue Ics = Icu
400 / 440 V ~ 65 kA
500 / 550 V ~ 55 kA
660 / 6 90 V ~ 50 kA
Icw 65 kA 1.0 s
36 kA 3.0 s
CAT. B 50 Hz / 60 Hz
IS/IEC 60947-2
IEC 60947-2
EN 60947-2
S r.No. : JQ677 7 00U
Su itab l e fo r 50 ° C
MA D E IN I N D I A
Stabilise systems with technology.
Weather electrical storms with reliability. 2
Electrical power is the lifeline of industry, but it is OMEGA ACB range consists of highly compact units
unpredictable. Just like an ocean, it can be calm one designed for high current, high power applications in
moment and turbulent the next. You cannot predict Low Voltage (LV) distribution network systems.
when a sudden dip or surge will happen, but you can They are equipped with state-of-the-art Matrix
protect your installation from damage, when it does. protection and control releases to meet the most
That’s where our highly sophisticated OMEGA ACBs demanding protection and system co-ordination
can make a world of difference to the safety of an requirements. All this, with the assurance of
organisation’s employees, systems and infrastructure. compliance to the L&T ‘Safe & Sure’ policy.
Awarded ‘Overall Best Product

by an Indian Exhibitor‘
at ELECRAMA
U W 1-0 8S
3 POLE
I n: 800A U imp: 1
2kV
Ue Ics = Icu
400 / 440 V ~ 65 kA
500 / 550 V ~ 55 kA
660 / 690 V ~ 50 kA
Icw 65 kA 1.0 s
36 kA 3.0 s
IS/IEC 60947-2
IEC 60947-2
EN 60947-2
00U
Sr.N o .: JQ 67 77
Sui tab l e for 50°C
MADE IN IND IA
L&T -The bedrock of stability.

Over the last five decades, Larsen & Toubro has earned In keeping with our leadership position in the Indian
a place among the leading manufacturers of market, we also provide expert assistance in product
Low Voltage Switchgear in the world, with the scale, selection, installation and effective after-sales service,
sophistication and range to meet global benchmarks. across the country.
Change course quickly.
Meet new challenges easily. 4
The OMEGA ACB range has been designed to adapt to • Let your systems have better co-ordination
changes in your requirements, and allow you to modify with protection devices and downstream loads,
or upgrade your systems with ease. This means via a wide range of protection curves and
minimum down-time and enhanced protection at all fine adjustment of current pick-up threshold and
times. time-delay settings.
Get the OMEGA advantage • Control a vast electrical installation through
• Meet system upgradation needs with Zigbee communication, along with the option of
ease throughout the life of your product, with click- conventional industrial communication protocols
fit, easy-to-mount front accessories like U/V and U/V such as MODBUS and PROFIBUS.
delay modules, Shunt and Closing releases. • Customise terminals by configuring terminal
• Enjoy total system flexibility and scalability adaptors for Vertical/Horizontal busbar
by adding power metering and communication arrangements, to facilitate termination of
modules or by enabling/disabling each protection Aluminium and Copper busbars.
function, depending on the requirement. Refer page No. 127-129 for recommended busbar
sizes for termination.
• Convert ACBs easily on site from Fixed to
Draw-out or from Manual to Electrical versions.
Match performance with prudence.
Move ahead, swiftly and safely. 6
OMEGA ACBs offer you the best of both worlds – high Negating human error with safety features
performance coupled with a range of exclusive features • No Arc-chute, No closure: Unique features like
that deliver the highest level of electrical safety. Arc-chute Interlocking and True Ready-to-Close
Performance par excellence (RTC) detection systems ensure that the ACB closes
• Save valuable space with world’s most compact only when the Arc-chutes are in place and all other
pre-requisite conditions are fulfilled.
ACBs, starting at just 347mm in width.
• Power ON, No racking operation: An inbuilt
• Enjoy total reliability in even the harshest of
Smart racking-shutter ensures that the ACB is
conditions including high ambient temperatures and
racked-in/out only in 'OFF-state'.
humidity levels.
• One signal, One closure: An inbuilt Electrical and
• Savour operational flexibility, as the ACB
Mechanical Anti-pumping System cancels the
discriminates between fault zones selectively,
persistent closing signal after successful ACB
allowing downstream equipment to clear the fault in
closure.
a prescribed time before intervening.
• No unauthorised setting changes: An innovative
Password Protection feature ensures that only
authorised personnel can change the release
settings.
Adopt technological brilliance.
Enjoy total peace of mind. 8
OMEGA ACBs are loaded with superior technology, L&T's wide range of Electrical Standard Products
across three frame sizes for the entire current range includes powergear, controlgear, energy management
from 400A to 6300A. These features, including devices, building electrical and automation products –
systems for communication, control and protection each of which matches and exceeds global benchmarks
(Matrix), make these ACBs a dream to use. for reliability and quality. However, in order to ensure
that your business sails smoothly through any electrical
OMEGA ACBs allow you to:
• View a snapshot of all parameters and symptoms turbulence, every element must be in perfect working
through a user-friendly, state-of-the-art O-LED condition.
Display. At L&T, we offer you the benefit of five decades of
experience in providing After-Sales Service for Low
• Control the system parameters of vast installations
Voltage Distribution Systems in every type of industry
easily, with a special Smart-card feature and
and building in India.
user–friendly Touch-Screen Display.
• Manage energy consumption better by monitoring The L&T Service Advantage
various energy parameters such as phase • Preventive Maintenance: Advice is provided and
components, power factors, energy and maximum preventive checks carried out on a regular basis.
demand. • Service On Call: A network of over 100 approved
• Communicate between system elements wirelessly Service Centres across India ensures that service is
and stay informed at all times through mobile alerts. just a phone call away.
• Add and remove Arc-chutes and various Volt- • Annual Maintenance Contract: Comprehensive
metric releases easily, without the need for tools. care for your systems including Obsolescence
Management and Part Replacement, as deemed
• Upgrade systems for safety, protection, control
necessary.
and monitoring with a wide range of accessories
and safety interlocks for versatile applications. • Obsolescence Management: We offer spares and
retro-fitment services, including upgrading all L&T
• Enjoy the benefit of total system compliance with
Switchgear, to ensure that your systems run
all the relevant quality, safety and environmental
standards. smoothly.
• Training on Product Usage: Our service engineers
work with customers' maintenance staff to train
them in the operation of switchgear products.
Keep an eye on upkeep.
Sail smoothly to greater success. 10
Special Applications-
800V AC / 1000V AC Rated Voltage Applications:
Specially designed OMEGA ACB range offers a solution for electrical applications with system voltages of 800V and
1000V AC. This range of ACBs maintain the same dimension and accessories as the standard 690V AC range. This
range of ACBs is available with LSI and LSING Protections through Microprocessor Releases-
1) MTX1.0 - LSI Protection

2) MTX1G - LSING Protection
3) MTX1.5G - LSING Protection with Current Metering
4) MTX1Gi - LSING Protection with Inbuilt ZSI
5) MTX1.5Gi - LSING Protection with Current Metering & Inbuilt ZSI
This Range of ACBs available for Current Ratings 400A-6300A in N Version therefore it offers
Icu=Ics=Icw (1Sec) = 50kA.
NOTE:
Please contact our nearest Sales Office for further Technical and Ordering details.
To find the perfect OMEGA ACB to protect your

systems from electrical turbulence, turn the page.
UW1-08S
3 POLE
I n: 800A U imp : 12kV
Ue Ics = I cu
400 / 440 V~ 65 kA
500 / 550 V~ 55 kA
660 / 690 V~ 50 kA
I cw 65 kA 1.0 s
36 kA 3.0 s
CAT.B 50 Hz / 60 Hz
IS/IE6C 0947 - 2
IEC 6 0947 - 2
EN 60947 - 2
Sr.No.: JQ677700U
Suitabel for 50°C
MADE IN INDIA
? ? ?
? ? ? ?
INDEX
13 Air Circuit Breakers
25 Matrix Protection & Control Units
69 Accessories
83 Control Circuit Wiring
91 Mounting & Termination
132 ACB Ordering Information

U W 1-08S
3 POLE
Ue Ics = Icu
400 / 440 V ~ 65 kA
500 / 550 V ~ 55 kA
660 / 690 V ~ 50 kA
Icw 65 kA 1.0 s
36 kA 3.0 s
IS/IEC 60947-2
IEC 60947-2
EN 60947-2
Sr.No .: J Q 6 7 7 7 0 0 U
Su it ab l e f o r 5 0° C
MA D E IN IN D I A
U W 1-0 8 S
3 POLE
Ue Ics = Icu
400 / 440 V ~ 65 kA
500 / 550 V ~ 55 kA
660 / 690 V ~ 50 kA
Icw 65 k A 1.0 s
36 k A 3.0 s
IS/IEC 60947-2
IEC 60947-2
EN 60947-2
00U
S r.No .: J Q 6 7 7 7
Su i t ab l e f o r 50° C
M AD E I N I N DI A
UW 1 -08S U W 1-0 8S
UW1-08S 3 POLE
3 POLE
I n:3 8POLE
00A U imp: 12kV I n: 800A U imp: 12kV
I n: 800A U imp : 12kV
Ue Ics = Icu Ics = Icu

I I
cs = cu
Ue
Ue
/ 440 V~ 65 kA
400400 / 440 V~ 55 kA
65 kA 400 / 440 V ~ 65 kA
500500/ 550 V~ 55 kA 500 / 550 V ~ 55 kA
/ 550 V~ kA
660660/ 6/9690 ~
0 V V~ 50
50 kA
660 / 690 V ~ 50 kA
IcwI cw 6565kA .0 ss
kA 11.0
.0 s
kA 33.0
3636kA s Icw 65 kA 1.0 s
36 kA 3.0 s
60 HHzz
Hz // 60
5050Hz
CATCAT.B
.B
I C 60947 - 2
IS/E
ECC 60947-2
ISI/IE 60947 - 2
477--2
IEECN 6600994 2
IS/IEC 60947-2
Sr.No.:EN
60947-2
JQ677700U IEC 60947-2
7700U
6 7 50°C EN 60947-2
tabJleQfor
Sui.:
S r.No
MADE IN INDIA Sr. No. : J Q 6 7 7 7 0 0 U
Su it ab le f or 5 0° C
MA DE I N I N D IA Suit abl e for 5 0 ° C
M A D E IN I N D IA
ACBs 14
UW1- 08S
3 POLE
I n: 800A U imp:
12kV
Ue Ics = Icu
400 / 440 V ~ 65 kA
500 / 550 V ~ 55 kA
660 / 690 V ~ 50 kA
Icw 65 kA 1.0 s
36 kA 3.0 s
IS/IEC 60947-2
IEC 60947-2
EN 60947-2
0U
S r.No. : JQ67770
Su it a b le fo r 5 0° C
MA D E IN IN D IA
Ø
Complete range conforms to IS/IEC 60947-2 & IEC 60947-2
Ø
Current rating from 400A to 6300A in 3 frame sizes
Ø
Available in 3 Pole/4 Pole, Manually & Electrically operated, Fixed & Draw-out versions
Ø
Common Height & Depth across the range
Ø
High short-time fault withstanding capacity, Icu = Ics = Icw for 1 sec for total selectivity
Ø
High mechanical and electrical operating life
Ø
Modular & snap-fit accessories
Ø
Ease of on-site conversion from Fixed to Draw-out & Manual to Electrical versions
Ø
Best in class Termination overlap with Bus bars.
Ø
RoHS compliant
Breaking Capacities: Icu = Ics = Icw

Rated current 800A 1000A 1250A 1600A 2000A 2500A 3200A 4000A 5000A 6300A
N : 50kA
Frame-1
S : 65kA
H : 80kA
UW1-08 UW1-10 UW1-12 UW1-16 UW1-20 UW1-25
N : 50kA
Frame-2
S : 65kA
H : 80kA
UW2-08 UW2-10 UW2-12 UW2-16 UW2-20 UW2-25 UW2-32 UW2-40
H : 80kA
Frame-3
V : 100kA
UW3-08 UW3-10 UW3-12 UW3-16 UW3-20 UW3-25 UW3-32 UW3-40 UW3-50 UW3-63
Note: 400A & 630A versions also available.

15 Technical Data Sheet
Automatic circuit breaker upto 690V AC :
Frame 1 2 3
0 (1) (2) (3)
Rated Uninterrupted Current (In) (A) at 50 C 400-2000 2500 400-4000 400-5000 6300
(4)
Version N S H S H N S H H V H V
Rated Operational Voltage at 50/60 Hz. Ue upto 690V AC
Rated Insulation Voltage at 50/60 Hz. Ui 1000V AC
Rated Impulse withstand Voltage Uimp 12kV (Main Circuit) & 4kV (Auxiliary Circuit)
Suitability for Isolation Yes
Degree of Protection on Breaker front IP53 Standard, IP54 Optional
Degree of Impact Protection on Breaker front IK08 Standard, IK10 Optional
Pollution Degree Suitability 4
Utilization Category B
Compliance IS / IEC 60947 (Part-2), EN 60947-2, IEC 60947-2
Operational Temperature Range O O

(As per IEC 60068-2-1/ IEC 60947-1-Q) -25 C to 70 C
Storage Temperature Range
(As per IEC 60068-2-1/2) -40OC to 85OC
415/440V AC 50 65 80 65 80 50 65 80 80 100 80 100

Rated Ultimate S.C.
Breaking Capacity Icu (kA) 500/550V AC 42 55 65 55 65 42 55 70 70 85 70 85
660/690V AC 36 50 55 50 55 36 50 55 65 75 65 75
415/440V AC
Rated Service S.C.
Breaking Capacity Ics (kA) 500/550V AC 100% Icu
660/690V AC
0.5sec 50 65 80 65 80 50 65 80 80 100 80 100

Rated Short-time
Withstand Capacity Icw (kA) 1.0sec 50 65 80 65 80 50 65 80 80 100 80 100
3.0sec 26 36 44 36 44 26 44 50 65 75 65 75
415/440V AC 105 143 176 143 176 105 143 176 176 220 176 220
Rated S.C. Making
Icm (kA) 500/550V AC 88 121 143 121 143 88 121 154 154 187 154 187
Capacity
660/690V AC 76 105 121 105 121 76 105 121 143 165 143 165
Break Time (ms) 25
Closing Time (ms) 60

(5)
Mechanical Life With Routine maintenance 20000 15000 10000
With Specific maintenance 20000 15000 10000

(5)
Electrical Life
With Routine maintenance 10000 5000 5000 5000 2000
Width 3P 347 447 647

W (mm)
Width 4P 447 581 847
Fixed ACB
D (mm) Depth 324 334
H (mm) Height 430

Dimensions
Width 3P 347 447 647
W (mm)
Width 4P 447 581 847
Draw-out
ACB D (mm) Depth 431
421
H (mm) Height 433
(1) Please consult branch office for selection (4) Available till 3200A
(2) Frame-2 4000A available in S & H Version only (5) Value corresponds operating cycle
O
(3) Rated Uninterrupted Current (In) (A) at 40 C Refer User’s Manual for Routine/Specific maintenance
Technical Data Sheet 16
Automatic circuit breaker 800V AC & 1000V AC :
Frame 1 2 3 2
0
Rated Uninterrupted Current (In) (A) at 50 C 400-2000 400-3200 400-6300 400-3200
Version N-08 N-10
Rated Operational Voltage at 50/60 Hz. Ue 800V AC 1000V AC
Rated Insulation Voltage at 50/60 Hz. Ui 1250V AC
Rated Impulse withstand Voltage Uimp 12kV (Main circuit) & 4kV (Auxiliary circuit)
Suitability for Isolation Yes
Degree of Protection on Breaker front IP53 Standard, IP54 Optional
Degree of Impact Protection on Breaker front IK08 Standard, IK10 Optional
Pollution Degree Suitability 4
Utilization Category B
Compliance IS / IEC 60947 (Part-2), EN 60947-2, IEC 60947-2

Operational Temperature Range O O
(As per IEC 60068-2-1/ IEC 60947-1-Q)
-25 C to 70 C
Storage Temperature Range O O
(As per IEC 60068-2-1/2) -40 C to 85 C
Rated Ultimate S.C. 800V AC 50 50

Breaking Capacity Icu (kA)
1000V AC - 50
Rated Service S.C. 800V AC 100% Icu 100% Icu

Breaking Capacity Ics (kA)
1000V AC - 100% Icu
0.5 sec 50kA, 800V AC 50kA, 1000V AC

Rated Short-time
Withstand Capacity Icw (kA) 1.0 sec 50kA, 800V AC 50kA, 1000V AC
3.0 sec 50kA, 800V AC 50kA, 1000V AC
800V AC 105 105

Rated S.C. Making
Icm (kA)
Capacity
1000V AC - 105
Break Time (ms) 25 25
Closing Time (ms) 60 60

(1)
Mechanical Life With Routine maintenance 20000 15000 10000 15000
(2)
With Specific maintenance 20000 15000 10000 15000
(1)
Electrical Life
With Routine maintenance 1000 1000 1000 1000
Width 3P 347 447 647 447

W (mm)
Width 4P 447 581 847 581
Fixed ACB
D (mm) Depth 324 334 324
H (mm) Height 430

Dimensions
Width 3P 347 447 647 447
W (mm)
Width 4P 447 581 847 581
Draw-out
ACB D (mm) Depth 421 431 421
H (mm) Height 433
(1) Value corresponds operating cycle

(2) With necessary component replacement
17 Technical Data Sheet
Automatic circuit breaker upto 690V AC:
W D
H : Height
W : Width
D : Depth with flat terminals
Rating Specification Parameters for 50% N ACB

Frame II III
Version S H/V
Rated Uninterrupted Current at 50OC In (A) 4000 3200-5000
Fixed ACB 581 747
Dimensions W (mm)
Draw out ACB 581 747
Rating Specification Parameters for 200% N ACB

Frame I II III
Version N&S S&H H
Rated Uninterrupted Current at 50OC
(1)
In (A) 400-1250 1600 -2000 2000-2500
Fixed ACB 447 581 647
Dimensions W (mm)
Draw out ACB 447 581 647
N also available
(1) 1600A
Identification 18
UV Release Closing Release Shunt Release

415~,400V 415~,400V 415~,400V
29k 29a
12 O UW1-08S
29g 3 POLE 29b
I I n: 800A
Ue
U imp: 12kV
Ics = Icu
29c
29h
400 / 440 V ~ 65 kA
UW1 -08S 500 / 550 V ~ 55 kA
DISCHARGED 3 POLE
I n: 800A Uimp: 12kV 660 / 690 V ~ 50 kA
13 Ue
I = Icu
cs
65 kA
29j Icw 65 kA 1.0 s
400 / 440 V ~ 55 kA
500 / 550 V ~
660 / 690 V ~ 50 kA 36 kA 3.0 s
I 65 kA 1.0 s
cw
36 kA 3 .0 s CAT. B 50 Hz / 60 Hz
CHARGED 50 Hz / 60 Hz 29d
CAT. B
29e
IS/IEC 60947-2
IEC 60947-2
EN 60947-2
00U
Sr. N o.: J Q 6 7 7 7
S uita ble for 5 0° C IS/IEC 60947-2
M A DE I N IN D IA
IEC 60947-2 29f
EN 60947-2
Sr.N o. : J Q 6 7 7 7 0 0 U
2a Suitable for 50°C
Charging Device
240V~,240V MADE IN INDIA
2b
2a - Type designation for Electrical

Charging device (ECD)
2b - Operating voltage for ECD
29a -
UW1-16S 29b - Rated Uninterrupted Current
29c - Rated impulse withstand voltage
29d - Utilization Category
4a - Type designation for Under- Rated 29e - Suitability for isolation
voltage release (UVR) Version for
Uninterrupted Breaking 29f - Standards compliance
4b - Operating voltage for UVR Current (In) 29g - Rated Service breaking capacity
5a - Type designation for Closing Capacity
29h - Rated operational voltage
release (CR) 04 400A
29j - Rated short-time withstand current
5b - Operating voltage for CR 1 Frame 1 06 630A N 50 kA
2 Frame 2 08 800A S 65 kA 29k - No. of Pole & Pole details
6a - Type designation for Shunt
release (SR/SRW) 3 Frame 3 10 1000A H 80 kA
12 1250A V 100 kA
6b - Operating voltage for SR/SRW 16 1600A
12 - ON-OFF indication N08 50 kA,800VAC
20 2000A 1000VAC
N10 50 kA,
13 - Spring status indication 25 2500A
32 3200A
40 4000A
50 5000A
63 6300A
19 Breaker Details
21
Breaker: 5
6 10
8b 24b
1 Protection & Control Unit
2 Electrical Charging Device
3a Auxiliary Contacts 3a
4 Under-voltage Release
4c Under-voltage Release Controller 4c
5 Closing Release 4
6 Shunt Release
7 Ready-To-Close (Microswitch)
8b Secondary Isolating Contacts
2
on Breaker
10 Operation Counter
12 ON-OFF Indication 12
13 Spring Status Indication
14 Charging Handle
13
21 Arc-Chute 33
24b Lifting Location on Breaker

33 Projection for resting Breaker on Cradle 14 7
1
Facia:
11 Shroud for ON-OFF Buttons
18 11a OFF Button
11b ON Button
11a 18 OFF Button locking
29 Laser Marked Breaker
11
Specifications
11b 29 31 Cover for Protection & Control
Unit (UW-MTX Releases)
32
32 Facia Fixing screw
31
Cradle Details 20
22 8e 40 37 34
24
8c 24
24a
24a
23
35
3j
38
39
3e
26
25
16 27
16a
17 19 20 15 36
Cradle:
3e Hole for Earthing Connection 19 Position Lock – 1 34 Guide for routing Control
Wiring
3j Jaw Contacts 20 Position Lock – 2
35 Terminal Supports
8c Secondary Isolating Contacts 22 Arc-Shield
on Cradle 36 Cradle Bottom cross-
23 Rating Error-Preventer component
8e Electrical Position Indication
24 Lifting Locations (4 nos.) 37 Cradle Top cross-component
15 Racking Handle
24a Additional Lifting Locations 38 Slot for placing breaker on
16 Smart Racking-Shutter Cradle
25 Withdrawal Rails
16a Pad-lock for Racking-Shutter 39 Safety Shutter
26 Door Racking Interlock
17 Position Indicator 40 Door-Interlock
27 Breaker Pull-out Handle
21 ACB “A Basket of Benefits”
User friendly:
E
Unique breaker front-facia architecture displays the electrical
accessories mounted on the ACB (with rated control voltage & type
of operating voltage) Shunt Release
220-240V~
E
Modular & snap-fit accessories such as UVR, SR & CR modules,
redefine the modularity on a time scale of 5 mins.
E
Ease of on-site convertibility from Manual to Electrical & Fixed to
Draw-out version
E
Tool-less Arc-Chutes removal facilitates quick inspection of OFF ON
PWR
O/L
S/C
INST
EF
electrical contacts
NTRL
ALRM
TRIP
O FF
E
Indelibly marked Breaker Specifications on facia with Laser Marking
E
RoHS complaint
Switchboard friendly:
E
Three compact frame sizes help in optimizing the switchboard
E
Right aligned design of ACB helps in better space utilization within the
switchboard
E
True 50% & 200% neutral options, along with the conventional
100% neutral (as standard) help in designing the switchboards as per
applications & lead to optimized switchboard design
E
Common height & depth across the range help in reducing the
number of connection layouts & facilitate the easy modification of
panel design & busbar layouts
E
Terminal adaptors offer ease of configuration of vertical/horizontal
busbar arrangements
E
Option of interleaving busbar design at breaker terminals offer
superior performance
E
Supports multi-tier arrangement with minimal clearance with the help
of arc-shield
E
Self-aligning, Snap-fit Secondary Isolating Contacts enable the quick
termination of 2 control wires (with Lugs) each of up to 2.5 sq.mm
E
Option of customized neutral configuration ( For 100%N only)
E
2m/3m/5m Bowden wire mechanical interlocking kit facilitates ease of
mechanical interlocking among various frames of Fixed / Draw-out /
Mixed versions of Omega ACBs
E
Minimum 45mm(Without Temperature Module) clearance above
breaker facilitating Compact Multi-tier Switchboard design
E
Best in class (40mm) Termination overlap with Bus bars.
A2
A1
ACB “A Basket of Benefits” 22
Superior Safety & Security:
E
Inbuilt Electrical & Mechanical Anti-pumping prevents multiple
breaker closures due to persistent closing commands
E
Arc-Chute interlocking prevents the closure of ACB if arc-chute is
missing or not properly installed
E
Smart-racking shutter interlock ensures that breaker is switched-off
before it is being racked-out
E
Unique True Ready-To-Close (RTC) gives electrical signal after
ensuring that:
a) Main spring is charged

b) Shunt release is de-energized
c) Under-voltage release is energized
d) Racking-Shutter is closed
e) Trip indication lever on electronic release is reset
f) Breaker is OFF
g) Arc-Chutes are properly placed
E
Closing of ACB only in distinct Service/Test/Isolated positions
ensures safety of the operating personnel
E
Door-Racking interlock prevents rack-in/rack-out operation of
breaker if panel door is open
E
Modular safety-shutters to prevent unintended contact with
terminals
E
Rating Error-preventer avoids the breaker-cradle mismatch of rated
current & breaking capacity version
E
Option to pad-lock the ON/OFF push buttons independently to
prevent unauthorized operations
E
Facility to lock breaker in OFF condition offers the key-lock based
interlocking arrangement
E
Option for pad-locking the racking-shutter prevents the inadvertent
racking operation & facilitates implementation of ‘LOTO’ system in
industry
E
Flexibility of locking the ACB in all positions or only in disconnected
position
E
Door-interlock prevents the opening of panel door in Service & Test
positions
E
Double insulation from Front Face (Class II operating safety)
E
Shock & Vibration Protection as Per IEC-60947-1/IEC-60068-2-6/27
Vibration : 2 to 13.2Hz +/-1 mm
13.2 to 100Hz 0.7g
Shock: 15g for 11ms Half-sine wave
23 ACB “A Basket of Benefits”
A
N
T
I-
P
UMP
I
NGI
NOM
E
G
AA
I
RC
IR
C
UI
TB
RE
A
KE
R
Anti-pumping device is one which prevents the breaker from reclosing after an opening operation even though the
device initiating closing is maintained in the position of closing.
Anti-pumping is generally achieved by providing electrical interlocks which ensure that the persistent closing
command breaks the moment the breaker trips on fault or opens. The breaker can then be reclosed only after a fresh
command is given. This method of providing anti-pumping is known as electrical anti-pumping.
Following anti-pumping methods are used to ensure reliability of entire distribution system.
• M
e
c
h
an
i
ca
la
n
ti
-
pum
p
i
ng
Mechanical anti pumping is achieved by providing linkage interlocks which ensure that anti-pumping lever does
not reset until the manual persistent closing command is relieved. Even in case of a fault, breaker trips but the
anti-pumping lever remains in the downward position until a persistent command is relieved. Hence the breaker
can be reclosed only after a fresh command is given.
• E
l
e
ct
ri
c
ala
n
ti
-
pum
p
i
ng
a
)B
yp
r
o
vi
di
ng
ex
t
e
rn
al
ci
r
cui
t
To achieve this anti-pumping, there is a need for an auxiliary contactor or a relay which will get actuated by
the first closing command and will break the closing circuit and will prevent the breaker from closing after
the breaker has tripped on fault, this anti-pumping contactor or relay is reset only when the closing
command is removed, thus proving anti-pumping.
B
)B
yh
a
v
in
g
in
b
ui
l
tf
ea
t
ur
e
in
cl
os
i
ng
re
l
e
ase
(
C
R)o
f
OM
EG
A
AC
B
In OMEGA, closing release consists of an electronic circuit to ensure no watt loss, inspite of continuous
power supply, thus saving energy.
When a closing command is given, closing coil of the circuit breaker gets supply through an electronic circuit
which comprises of IC555 timer. The closing coil is energized and the breaker closes. The closing command
persists only for the 500ms time duration. In order to close the circuit breaker again, the closing coil circuit
will have to be reset only when the closing command is removed. This ensures that once the breaker has
closed and tripped on fault the breaker can close again only after the first closing command is removed and a
fresh closing command is given, thus providing anti-pumping.
ACB 24
Matrix
Protection & Control Units
UW-MTX4.5
?
Matrix Release Family 26
UW-MTX4.5
UW-MTX3.5 H
UW-MTX 1Gi
UW-MTX 4.5
Advanced Version
UW-MTX 1.5Gi
?
?
UW-MTX 3.5H
?
UW-MTX 1G
UW-MTX 1.5G
UW-MTX 3.5/3.5EC
UW-MTX 1Gi/1.5Gi
?
UW-MTX 1.0/1G/1.5G
Basic Version
27 Matrix Release "A basket of benefits"
1) State-of-the-art touch-screen technology in Matrix 4.5 releases offer ease of navigation
2) Unique withdrawable power metering & communication modules offer ease of flexibility, scalability &
customization of electrical systems
3) Option of both Modbus & Profibus industrial communication protocols
4) Zigbee offers wireless monitoring parameters of Matrix releases & supplementary modules
5) Wide range of Overload protection curves (such as I2t, I4t, SI & LI/VI) offer precise co-ordination with large
variety of electrical loads
6) Option of Enabling/Disabling each protection function offers greater flexibility in designing the overall
protection system
7) Directional & Double Short-circuit protection
8) Password protection in releases prevents unauthorized access to protection release
9) Unique O-LED display offers better contrast & wider-viewing angle
10) Ease of parameterisation through Configurator modules
11) Dual time-based set group protection provides the option of setting two sets of protection curves
12) Front connector for hand-held testing of release
13) Soft-rating plug offers precise protection of electrical system at lower value of system currents
14) Query button for last trip information furnishes the “Trip Info” details such as cause of tripping, date and
time stamping of tripping
15) Test button for self-diagnostic test
16) 20 trip & 128 event records stored in the protection release*
17) Elimination of relays & measurement devices

l Less time required for switchboard assembly (no wiring or cut-outs on the front panel)
l Fewer devices required and less time spent on their selection, purchase, storage and installation
18) Harmonics metering up to 27th order of fundamental frequency along with display of THD
19) Oscillograph of fault current waveforms (10 cycles before pick-up/Trip & 5 cycles after pick-up/Trip)
20) Tested for Electromagnetic Compatibility (EMC) as per IEC-60947-2
21) Inbuilt & Optional Zone Selective Interlocking (ZSI)
* a : 20 trip and 10 events can be accessed on Release display.

b : 20 Trip and 128 events can be accessed through communication.
Matrix Release "Innovation in Imagineering" 28
UW-MTX3.5EC UW-MTX4.5
Indicator LEDs
Indicator LEDs
Touch-Screen Navigation
Navigation Keys
Escape Key
Self-test
? Query Key ?
Test Port
Modbus/Profibus/Zigbee
Smart Card Module
Metering Module
Indicator LEDs O-LED Display
BCD Switches
DIP-Switches
Query ? Self-test
29 Matrix "Redefining Modularity"
Matrix releases designed for “Flexibility, Scalability & Customization” offer wide variety of withdrawable modules
such as Modbus, Profibus, Zigbee, Smart Configurator & Power metering. To start with one can go for a basic version
of MTX3.5 release and based on future needs and system demands, one can upgrade the protection release with
Power metering & Communication modules.
Basic Protection Unit
?
? Communication Modules
(Modbus, Profibus, Zigbee)
Smart Card Module
Power Metering Module
MTX4.5
MTX3.5EC
Matrix Protection and Control Units 30
UW-MTX 1G UW-MTX 1Gi UW-MTX 1.5G UW-MTX 1.5Gi
? ? ? ? ?
UW-MTX1.0 UW-MTX1G/1Gi UW-MTX1.5G/1.5Gi

Features:
2
• Overload, Short-circuit & • I t ON curve for Short-circuit • Inbuilt rating-plug through
Instantaneous protection with & Earth-fault protection DIP switches
adjustable current & time- • Current Metering in • Test button to check the
delay settings MTX1.5G/1.5Gi through health of protection release
• Inbuilt Earth-Fault & neutral 3-line O-LED display • Self-powered protection
protection in MTX1G/1Gi & • Local fault annunciation • Inbuilt Zone Selective
MTX1.5G/1.5Gi through LED indication & Interlocking (ZSI) in MTX1Gi
• Switchable thermal memory pre-trip alarm & MTX1.5Gi
for cable protection on • Front accessible test port
repetitive overloads • Query button for last trip
record
Protection parameters:
Parameters MTX1.0 MTX1G MTX1Gi MTX1.5G MTX1.5Gi
Protection: Enable/Disable ü ü ü ü ü
Pick-up (Ir)=In x... for I2t OFF- 0.4-0.5-0.6-0.7-0.8-0.85-0.9-0.95-1
Overload (Phase) Delay (tr) in sec 10 0.5-1-2-4-6-12-18-24-30
Pre-alarm 0.9 x Ir (fixed)
Thermal Memory ON/OFF ü ü ü ü ü
Protection: Enable/Disable - ü ü ü ü
Pick-up (IN)=Ir x... - 50%-100%-150%-200%
Overload (Neutral) -
Pre-alarm 0.8 x IN (fixed)
Delay (tr) in s - Same as Overload Phase
Protection: Enable/Disable - - - - -
I2t ON/OFF ü ü ü ü ü
Short-Circuit Pick-up (Is)=In x... 0.6-1-1.5-2-3-4-6-8-10-12
Delay (ts) 20-100-200-300-400 ms
Pre-alarm 0.5 x Is (fixed)
Protection: Enable/Disable ü ü ü ü ü
Instantaneous
Pick-up (Ip)=In x... OFF-1.5-2-3-4-6-8-10-12-15
Protection: Enable/Disable - ü ü ü ü
I2t : ON/OFF - ü ü ü ü
Pick-up (Ig)=In x... - OFF-0.2-0.3-0.4-0.5-0.6
Earth-Fault
I2t OFF (tg) - 0.1-0.2-0.3-0.4-1
I2t ON (tg) - 0.1-0.2-0.3-0.4
Pre-alarm - 0.8 x Ig (fixed)
Short Circuit Enable/Disable - - ü - ü
Inbuilt-ZSI - - -
Earth Fault Enable/Disable ü ü
31 Matrix Protection and Control Units
UW-MTX3.5 H UW-MTX4.5
? ? ?
UW-MTX3.5/3.5EC/3.5H U
W
-
MT
X3
.
5
H UW-MTX4.5
F
e
at
u
re
s P
a
r
am
et
e
r M
T
X
3
.5 M
T
X
3
.C M
5
E T
X
3
.H M
5 T
X
4
.5
Overload - Phase P P P P
Overload - Neutral P P P P
Short-Circuit P P P P
Basic Protection
Directional Short-Circuit P P P P
Instantaneous P P P P
Earth-Fault P P P P
Current P P P P
Voltage * P P P
Additional Frequency * P P P
Protection Reverse Power * P P P
Maximum Demand * P P P
Trip Records Last 20 trip data P P P P
Event Records Last 10 Event Data P P P P
Smart Card * * * *
Modbus * P * P
Communication Profibus * * * *
Zigbee (wireless) * * * *
Trip Circuit Supervision (TCS) * * * *
Zone Selective Interlocking (ZSI) * * * *
Advanced Protection Temperature Rise (TM) * * * *
Earth Leakage (EL) * * * *
Restricted Earth-Fault (REF) * * * *
Relay Output * * * *
Load Management (Pre Trip Alarm) P P P P
Additional Features
Digital Input & Output * * * *
Analog Output * * * *
Current P P P P
% Loading P P P P
Metering Voltage P P P
*
Power & Energy * P P P
Harmonics - - P P
Storable Settings (2 sets) P P P P
Auxiliary Supply (24V DC) * * * P
* - Optional feature
P - Standard
UW-MTX3.5/3.5EC
Overload, Short-circuit and Advance protection - ZSI, TCS,
Earth-fault protection with REF & EL
UW-MTX3.5EC variable current & time delay Communication through
setting Modbus, Profibus & wireless
Instantaneous protection Zigbee
2 4
I t,I t, SI, LI/VI protection Smart Configurator module
curves for easy parameterisation of
the release
Directional & Double Short
circuit protections Local & remote fault
annunciation & pre-trip alarm
Reverse power and phase
sequence protection Current, Voltage, Power,
2 Energy & THD metering & %
? Selectable I t based curves for
loading
short-circuit and earth-fault
protection Earth Fault Protection from
Switchable neutral overload 10%In

protection (50%-200%) in Dual time-based protection set
step of 5% groups
Additional current & voltage Thermal reflectivity & soft
based protections rating-plug
Protection against Self-powered protection
temperature rise Trip & Event recording
UW-MTX3.5H
Overload, Short-circuit and Protection against
UW-MTX3.5H
Earth-fault protection with temperature rise
variable current & time delay Advance protection - ZSI, TCS,
setting REF & EL
Instantaneous protection Optional communication
2 4
I t,I t, SI, LI/VI protection through Modbus, Profibus &
curves wireless Zigbee
Current & Voltage Smart Configurator module
for easy parameterisation of
harmonics metering
the release
Directional & Double Short
Local & remote fault
circuit protections
? annunciation & pre-trip alarm
Reverse power and phase
Current, Voltage, Power,
sequence protection
Energy & THD metering & %
Selectable I2t based curves for loading
short-circuit and earth-fault
Dual time-based protection set
protection
groups
Switchable neutral overload
Thermal reflectivity & soft
protection (50%-200%) in
rating-plug
step of 5%
Self-powered protection
Additional current & voltage
based protections Trip & Event recording
UW-MTX4.5
Overload, Short-circuit and Earth- Metering of sequence components
fault protection with variable of current waveform, form factor,
UW-MTX4.5 current & time delay setting peak factor

2 4
I t, I t, SI, LI/VI protection curves Additional current & voltage based
protections
Navigation through Touch-Screen
Protection against temperature
Bar-graph representation of rise
current, voltage & power
parameters Advance protection - ZSI, TCS, REF
& EL
Directional & Double Short-circuit
protection Communication through Modbus,
Profibus & wireless Zigbee
Instantaneous protection
? 2
Local & remote fault annunciation
Selectable I t based curves for & pre-trip alarm
Short-circuit and Earth-fault
protection Dual time-based protection set
groups
Switchable neutral overload
protection (50%-200%) in step Thermal reflectivity & soft rating-
of 5% plug
Harmonics metering up to 27th Self-powered protection

order of fundamental frequency Trip & Event recording
along with display of THD
percentage
Oscillograph of fault current
waveforms (10 cycles before pick-
up/Trip & 5 cycles after pick-up/Trip)
UW-MTX4.5
Simulation Kit for Matrix releases

Universal test kit for all versions of Matrix releases
Generates 3 phase current and voltage with adjustable
phase angles
?
Graphical display & smart GUI with multi-functional key
operation
Portable & hand held device to simulate faults
Dual Power ON-battery & external supply
Auto sensing of release connectivity
Stores 10 test records
Basic protection in UW-MTX 3.5/3.5EC/3.5H/4.5 Series

Parameter UW-MTX3.5 UW-MTX3.5EC UW-MTX3.5H UW-MTX3.5H/4.5
Protection : Enable/Disable P P P P
2 4
Pick-Up (Ir)=In x ...for I t, l t, SI, LI/VI 0.4 to 1 In in step of 0.05
Overload (Phase) Delay(tr) in s 0.5-1-2-4-6-12-18-24-30
Pre-alarm 0.5 to 0.95 in step of 0.05 x lr
Thermal Memory ON/OFF P P P P
Protection: Enable/Disable P P P P
Pick-Up IN=Ir x ... 0.5 to 2 in step of 0.05
Overload (Neutral)
Pre-alarm 0.5 to 0.95 in step of 0.05 x IN
Delay(tr) in s same as Overload Phase
Double S/C ON/OFF P P P P
l2t ON/OFF P P P P
Pick-Up Lo, ls=In x ... 0.6 to 12 In in step of 0.05
Pick-Up Hi, ls=In x ... 0.6 to 12 In in step of 0.05
Short-Circuit
Delay Hi (ts) 20-100-200-300-400 ms
Delay Lo (ts) 20-100-200-300-400 ms
Pre-alarm 0.5 to 0.95 in step of 0.05 x ls
Cold Pick-Up ON/OFF P P P P
Cold Delay 100 ms to 10s in step of 100ms
Direction: Top/Bottom P P P P
l2t: ON/OFF P P P P
Pick-up(ls): ln x ... 0.6 to 12 In in step of 0.05
Directional Short-Circuit
Delay(ts) 20-100-200-300-400 ms
Pre-alarm 0.5 to 0.95 in step of 0.05 x ls
Cold Pick-Up ON/OFF P P P P
Cold Delay 100 ms 10s in step of 0.05 x ls
Instantaneous
Pick-up(lp)=ln x ... 1.5 to 10 in step of 0.1; 10 to 15 in step of 1
2
l t: ON/OFF P P P P
Pick-Up(lg)=ln x ... 0.1-0.2-0.3-0.4-0.5-0.6
l2t OFF(tg) 100 ms to 1s in step of 100 ms
2
Earth-Fault l t ON(tg) 100-200-300-400 ms
Pre-alarm 0.5 to 0.95 in step of 0.05 x lg
Cold Pick-Up: ON/OFF P P P P
Cold Delay 100ms to 5sec in step of 100 ms
Advanced protection in UW-MTX 3.5/3.5EC/3.5H/4.5 Series
Parameter UW-MTX3.5 UW-MTX3.5EC UW-MTX3.5H UW-MTX 4.5
Protection: Enable/Disable * P P P
Pick-Up=lr x ... 0.2 to 0.8 in step of 0.05
Under Current
Delay 1 to 255sec in step of 1sec
Mode: Trip/Alarm/Both * P P P
Pick-Up=ln x ... 10 to 90% in step of 5%
Current Unbalance
Delay 500 ms to 60s in step of 0.5s
Pick-Up(Vs)=Vn x ... 0.7 to 0.95 in steps of 0.01
Under Voltage Delay 100 ms to 5s in step of 100 ms
Vs reset 1.01/1.02/1.03/1.04 x Vs
Pick-Up(Vs)=Vn x ... 1.05 to 1.5 Vn in step of 0.01
Over Voltage Delay 100 ms to 5s in steps of 100 ms
Vs reset 0.95 to 0.99 Vs in step of 0.01
Pick-Up(Vs)=Vn x ... 5 to 20% in step of 1%
Voltage Unbalance Delay 500ms to 60s in step of 0.5s
Vs reset 0.95 to 0.99 Vs in step of 0.01
Pick-Up (Vs)=Vn x ... 0.15/0.2/0.25/0.3/0.4
Residual Voltage Delay 100ms to 5s in step of 100 ms
Vs Reset 0.95 to 0.99 Vs in step of 0.01
Pick-Up (Fn) 45-50 Hz in step of 0.1Hz
Under Frequency Delay 1-30sec in step of 0.1sec
Reset Freq 1.01 to 1.05 Fn in step of 0.01
Pick-Up (Fn) 50-55 Hz in step of 0.1 Hz
Over Frequency Delay 1-30sec in step of 0.1sec
Reset Freq 0.95 to 0.99 Fn in step of 0.01
Pick-Up=Pn x ... 0.05 to 0.4 in step of 0.01
Rev Power
Delay 100ms-20s in step of 0.1s
Earth Leakage**
Pick-Up(lr) 0.3 to 30A in step of 0.1 A
Delay 100-200-300-400-500 ms
2
I t: OFF/ON * P P P
Pick-Up(lg)=ln x ... 0.1 to 0.6 in step of 0.1
Restricted EF** l2t OFF (tg) 100 ms to 5sec in step of 0.1s
l2t ON (tg) 100-200-300-400 ms
Pre-alarm 0.5 to 0.95 in step of 0.05 x lg
Cold Pick-Up: ON/OFF 60 ms to 10s in step of 20ms
Available
P * Requires Power Metering module for Advanced Voltage based Protection
** Requires additional modules
Advanced Protection in UW-MTX 3.5/3.5EC/3.5H/4.5 Series

Parameter UW-MTX3.5* UW-MTX3.5EC UW-MTX3.5H UW-MTX4.5
Pick-Up=Pf x ... 0.5 to 0.99 in step of 0.01
Leading PF
Delay 1/2/3/4/5 s
Mode: Trip/Alarm/Both P P P P
Pick-Up=Pf x ... 0.5 to 0.99 in step of 0.01
Lagging PF
Delay 1/2/3/4/5 s
Type Deliver/Receive
MD Active
Pick-Up=En x ... 0.4 to 1 in step of 0.01
MD Reactive
MD Apparent
Phase Sequence Delay 100ms to 5s in step of 100ms
Breaker Failure
Delay 50ms to 2sec in step of 0.05sec
Available
P * Requires Power Metering module for Advanced protections
Metering Functions
Parameter Screen abbreviation Details MTX 3.5 MTX 3.5EC MTX3.5H MTX4.5
l Phase, Neutral and Earth P P P P
$
lΔ, lREF Earth Leakage, Restricted EF Current P P P P
Current l max Maximum Running Current Per Phase P P P P
% Load Percentage Loading Per Phase P P P P
Avg.I Average Phase Current P P P P
V Phase-Neutral Voltage * P P P
Max V Maximum Voltage Per Phase * P P P
V12 Ph-Ph Voltage * P P P
Voltage
Max V12 Maximum Ph-Ph Voltage * P P P
Avg. Vp-p Average Ph-Ph Voltage * P P P
Avg Vp-n Average Ph-N Voltage * P P P
Frequency F System Frequency * P P P
Power Factor PF System Power Factor * P P P
W Active Power Per Phase and Total (kW) * P P P
Power VAr Reactive Power Per Phase and Total (kVar) * P P P
VA Apparent Power Per Phase and Total (kVA) * P P P
Wh Active Energy Per Phase and Total (kwh) * P P P
Energy VArh Reactive Energy Per Phase and Total (kVArh) * P P P
VAh Apparent Energy Per Phase and Total (kVAh) * P P P
Wh Active Energy * P P P
Max Demand VArh Reactive Energy * P P P
VAh Apparent Energy * P P P
#
Temperature Ø Temperature Per Phase & Neutral (0C) P P P P
THD, Current &
Harmonics Metering Phase-1, 2 & 3-Total, Fundamental, THD - - P P
Voltage components
* Requires Power Metering module # Requires Temperature module

P Available
$ requires additional REF module
37 Matrix Protection Curves
Overload - I2t
(UW-MTX 1
.
0/
1G
/
1G
i
/
1.
5G
/1
.
5G
i/
3
.5
/
3.
5E
C/
3
.5
H/
4
.5
)
10000
1000
100
Trip Time (s)
10 30 sec
24 sec
18 sec
12 sec
6 sec
4 sec
1
2 sec
Instantaneous
1 sec
(UW-MTX 1
.
0/
1G
/
1G
i
/
1.
5G
/1
.
5
Gi/
3
.5
/
3.
5E
C/
3
.5
H/
4
.5
)
0.5 sec
10000
0.1
1 1.2 2 3 4 5 6 7 8 9 10
Current Multiples (x Ir)

Tolerance Trip Time: ±20%
100
10
1.5 15
Trip Time (s)
0.1
0.01
0.01 0.1 1 10
Current Multiples (x In)
Matrix Protection Curves 38
Short-Circuit - I2t ON
(UW-MTX 1.0/1G/1Gi/1.5G/1.5Gi/3.5/3.5EC/3.5H/4.5)
10000
1000
0.6 12
100
10
Trip Time (s)
0.4
0.3
0.2
Short-Circuit - I2t OFF

0.1
0.1
(UW-MTX 1.0/1G/1Gi/1.5G/1.5Gi/3.5/3.5EC/3.5H/4.5)
0.02
0.01 10000
0.01 0.1 1 10 50

1000
100
0.6 12
10
Trip Time (s)
0.4
0.3
0.2
0.1 0.1
0.02
0.01
0.1 1 10 50
2
Ground Fault - I t ON
(UW-MTX 1.0/1G/1Gi/1.5G/1.5Gi/3.5/3.5EC/3.5H/4.5)
10000
1000
0.1
0.2
0.3
100
0.4
0.5
0.6
0.8 2.4
Trip Time (s)
10
1
Ground Fault - I2t OFF
0.4 s
(UW-MTX 1.0/1G/1Gi/1.5G/1.5Gi/3.5/3.5EC/3.5H/4.5)
0.1 0.1 s 1000
0.01
0.4 2.4
0.01 0.1 1 10 50 100
0.6
10
Trip Time (s)
1 1
0.8
0.6
0.5
0.4
0.3
0.2
0.1
0.1
0.01
0.1 1 10 50

Matrix Protection Curves 40
Overload - I2t
(UW-MTX1.0)
10000
1000
100
Trip Time (s)
10
10s
Overload - I4t
1
(UW-MTX3.5/3.5EC/3.5H/4.5)
100000
0.1
1.2 2 3 4 5 6 7 8 9 10
Current Multiples (x Ir) 10000
1000
100
Trip Time (s)
10
30 s
24 s
18 s
12 s
1
6s
4s
2s
1s
0.1
0.5 s
0.01
1 1.2 2 3 4 5 6 7 8 9 10

Overload - SI
(UW-MTX3.5/3.5EC/3.5H/4.5)
10000
1000
100
30s
Trip Time (s)
24s
18s
10
12s Overload - LI/VI
6s
(UW-MTX3.5/3.5EC/3.5H/4.5)
4s
2s 10000
1
1s
0.5s
1000
0.1
1 1.2 2 3 4 5 6 7 8 9 10

100
Trip Time (s)
30s
24s
10 18s
12s
6s
4s
1 2s
1s
0.5s
0.1
1 1.2 2 3 4 5 6 7 8 9 10
O
v
e
rv
o
l
ta
ge
c
au
s
e
sa
nd
e
f
fe
c
t
s
Over voltage (or surges) in the power system are the abrupt rise in the voltage level in the system. There could be
several reasons for over voltage. The normal operating voltages of the system do not stress the insulation severely.
But the voltage stresses due to over voltages can be so high that they may become dangerous to both the cables and
the connected equipment and may cause damage, unless some protective measure against the over-voltages are
taken. Over-voltages occurrence in the system can be categorized by reasons:
1
.
EXT
E
RN
A
LO
V
E
RV
O
L
TA
G
ES
:
These over-voltages originate from the atmospheric disturbances, mainly due to lightning. These over-voltages
take the form of a unidirectional impulse whose maximum possible amplitude has no direct relation with the
operating voltage of the system. They may be due to any one of the following causes:
a. Direct lightning strokes
Cloud
Direct
Lightning
Phase Stroke
Conductor
Towers
b. Electromagnetically induced voltages due to the lightning discharge near the line (sidestroke)
c. Voltage induced due to the changing atmospheric condition along the transmission line
d. Electrostatically induced over voltages due to the presence of the charged clouds
e. Due to the friction of the charged particles like dust, snow in the atmosphere or due to change in the altitude
of the line
2
.
IN
TE
R
NA
L
OV
E
RV
O
L
TA
G
ES
:
Caused due to changes in the operating condition of the network. Can be further classified in two groups:
a
.S
wi
t
chi
ng
or
t
ra
ns
i
en
to
v
e
rv
o
lt
a
ge
s
These over voltages are generally of oscillatory nature caused by the transient phenomena which appears
when the state of the network is changed by switching operation or a fault condition.
The frequency of the oscillations is governed by the inherent inductance and capacitance of the system & may
vary from few hundred Hz to few kHz
For e.g. i. Switching On & OFF of equipment, like switching of high voltage reactors or switching of
transformer on no load
ii. If fault occurs in any one phase the voltage of other phases with respect to the ground increases
until the faults get cleared
iii. Because of the re-striking voltage across the contacts of the breaker, when breaker has tripped
on fault, voltage of amplitude nearly twice the system voltage and relatively high frequency gets
generated
b
.
Ste
a
dy
-
s
ta
te
o
rt
e
mpo
r
a
ry
ov
e
r
vo
l
ta
ge
s
These are over voltages developed due to the disconnection of loads at power frequency.
D
I
RE
CT
I
ONA
L
S
HO
RT
C
IR
C
UI
TP
RO
T
E
CT
I
ON
4 1 4 1
3 2 3 2
Load Load
Consider a single-end-fed system of parallel feeders. in the normal condition circuit Breakers 1, 2, 3 and 4 will be
closed and will feed the load through two parallel feeders (Fig1). when the fault occurs at point A Breaker 4 will see
the fault in its zone and trip as per its time delay settings. Breaker 3 will remain closed as fault is not in its zone. To
keep the load bus charged Breaker 1 and 2 should be closed and feed the load.
The direction of current flow at Breaker 3 will get reversed and allow to feed fault at point A as shown in fig 2.
reverse short circuit protection.To prevent such situation Breaker 3 should sense this reversal of power flow and
should trip immediatily to provide complete isolation of the fault at A. while the supply to the load remain intact
through the Breaker 1 and Breaker2. this funtion of Breaker 3 is called reverse short circuit protection.
Linear Loads:
The AC loads are called linear loads when the current and voltage resultant waveform is sinusoidal in nature (i.e. not
distorted). Also the current at any instant is proportional to the voltage at that instant.
Thus in linear systems there are no harmonic components in current and the voltage waveforms.
e.g. Heaters, Power factor improvement capacitors, etc.
Ir Iy Ib
0 0 0 0 0 0 0 0
3 PHASE FUNDAMENTAL WAVE
0 60 120 180 240 300 360 60
RESULTANT CURRENT I = Ir+Iy+Ib = 0
CURRENT WAVE FOR LINEAR LOAD
N
o
n
-L
i
ne
ar
L
oa
ds
:
The AC loads which cause the current waveform to distort from the normal sinusoidal nature are called as non-linear
loads. Current distortion leads to the distortion of the voltage waveform also. Thus the voltage and current are no
longer proportional.
The distorted current and the voltage waveforms can be decomposed into pure sinusoidal and associated
frequencies of the higher order through Fourier Transformation.
Harmonic spectrum gives a clear analysis of amount and order of the harmonics present in the system, which helps in
the designing the filter for the system.
e.g. SMPS, Rectifiers, PLC, Electronic Ballasts, Laser Printers, Computers, etc.
RESULTANT CURRENT
00 600 1200 1800 2400 3000 3600 600 WITH 3rd HARMONICS
RESULTANT CURRENT I = Ir+Iy+Ib
CURRENT WAVEFORM FOR NON-LINEAR LOAD
23:59
R-Phase
%
100
80
60
40
20
0
3 6 9 12 15 18 21 24 27
Component
HARMONIC SPECTRUM
Harmonics are basically the sinusoidal component of the periodic wave with frequency that is an integral multiple of
the fundamental frequency.
Harmonics content purely determines the quality of power. Having harmonics in the system will affect the system
and the severity of effect on the system/equipment will depend on the stiffness of the system and the amount of the
harmonic pollution.
H
a
r
mo
ni
c
sca
n
be
g
en
e
ra
t
e
di
nt
he
s
ys
t
em
be
c
a
us
eo
f
th
e
fo
l
l
owi
ng
re
a
s
on
s
:
• Non-linear loads generate current harmonics
• Harmonic currents flow largely through capacitors
• Harmonic currents also flow through network
• The flow of harmonic currents causes voltage harmonics
• Harmonics are thus injected to other linear loads connected in the same bus
• Harmonics injected into the network flow towards other users connected to the network
S
o
me
of
t
he
ty
p
i
ca
ll
oa
ds
c
au
si
ng
th
e
ge
n
er
a
ti
on
of
t
he
ha
r
mo
ni
c
si
nt
he
s
ys
t
em
ar
e
:
• Equipment using switched mode power supply:
4
Television
4
Computers, other IT loads
• Equipment using power electronic devices:
4
AC & DC drives
4
Frequency converters
4
Rectifiers
4
Arc & induction furnaces
4
UPS
S
o
me
of
t
he
ty
p
i
ca
lr
e
su
l
ts
of
t
he
ha
r
mo
ni
c
si
nt
he
s
ys
t
em
ar
e
:
1. Neutral over current: Odd triplen harmonics because of its additive nature adds up in the neutral current causing
the overheating of the neutral.
Fundamental of 50 Hz AC
3rd Harmonic
Phase R
3rd Harmonic
o
120
Phase Y
Lagging
3rd Harmonic
120o Phase B
Lagging
Fig.1
As shown in the Fig.1 any odd triplen harmonic when multiplied by 120 degrees will always produce the product
which is integral multiple of the 360 degrees. Thus being shifted by integral multiples of the 360 degrees, the odd
triplen harmonics will always be in phase with each other in neutral.
2. Incorrect readings: In case of induction disc W-hr meters and averaging type current meters
3. Additional losses in capacitors and rotating machines
4. Reduced true PF: Pf=watts/VA
5. Transformer overheating especially delta windings where triplen harmonics generated on the load side of a
delta-wye transformer will circulate in the primary side. Some type of losses go up as the square of harmonic
value (such as skin effect and eddy current losses). This is also true for solenoid coils and lighting ballasts.
6. Zero, negative sequence voltages on motors and generators. In a balanced system, voltage harmonics can either
be positive (fundamental, 4th, 7th...), negative (2nd, 5th, 8th...) or zero (3rd, 6th, 9th,...) sequencing values. This
means that the voltage at that particular frequency tries to rotate the motor forward, backward, or neither (just
heats up the motor), respectively. There is also heating from increased losses as in a transformer.
Harmonic order 1 2 3 4 5 6 7 8 9
Phase Sequence + - 0 + - 0 + - 0
7. Nuisance operation of protective devices, including false tripping of relays and failure of a UPS to transfer
properly, especially if controls incorporate zero-crossing sensing circuits.
8. Bearing failure from shaft currents through uninsulated bearings of electric motors.
9. Blown-fuses on PF correction caps, due to high voltage and currents from resonance with line impedance.
10. Mis-operation or failure of electronic equipment.
11. If there are voltage sub-harmonics in the range of 1-30Hz, the effect on lighting is called flicker. This is especially
true at 8.8Hz, where the human eye is most sensitive, and just 0.5% variation in the voltage is noticeable with
some types of lighting.
T
O
TA
L
HA
R
MO
N
I
CDI
S
TOR
T
I
ON:
Power sources act as non-linear loads, drawing a distorted waveform that contains harmonics. These harmonics can
cause problems ranging from telephone transmission interference to degradation of conductors and insulating
material in motors and transformers. Therefore it is important to gauge the total effect of these harmonics. The
summation of all harmonics in a system is known as Total Harmonic Distortion (THD).
Harmonics have frequencies that are integral multiples of the waveform’s fundamental frequency. For example,
given a 50Hz fundamental waveform, the 2nd, 3rd, 4th and 5th harmonic components will be at 100Hz, 150Hz,
200Hz and 250Hz respectively. Thus, harmonic distortion is the degree to which a waveform deviates from its pure
sinusoidal values as a result of the summation of all these harmonic elements.
The ideal sine wave has zero harmonic components. In that case, there is nothing to distort this perfect wave. Total
Harmonic Distortion or THD, is the summation of all harmonic components of the current waveform compared
against the fundamental component of the current wave:
The formula above shows the calculation for THD on a current signal. The end result is a percentage comparing the
harmonic components to the fundamental component of a signal. The higher the percentage, the more distortion
that is present on the mains signal.
23:59
THD Profile - B
%
100
90
80
70
60
50
40
30
20
10
0
23:59 07:59 15:59 23:29
Time
THD PROFILING
C
r
e
st
Fa
c
to
r
(
CF
)
:
T
h
eC
r
es
t
Fa
c
to
r
o
fap
o
we
r
so
u
rc
e
is
de
f
i
ne
da
s
:
Ip
e
a
k/I
R
MS
Crest Factor is an important parameter to understand when trying to take accurate measurements of low frequency
signals.
CF for sine wave = 1.414
However, the Crest Factor for a non-sinusoidal current waveform can differ dramatically for loads that are not power
factor corrected, such as a switching power supply or lamp ballast, which gives a current waveform that is short in
duration but high in amplitude.
CF specified in various communication devices QPSK, QAM, WCDMA should be maintained in the system for reliable
communication.
Form Factor (FF):

The Form Factor of a power source is defined as:
I/
RM
SI
a
vg
FF for pure sine wave = 1.11

FF remains independent of the amplitude of the waveform and will remain same for a particular waveform.
P
e
ak
F
ac
t
or
(
PF
)
:
T
h
eP
e
ak
F
ac
t
or
o
fap
o
we
r
so
u
rc
e
is
de
f
i
ne
da
s
:
I
pe
a
k/
Ia
v
g
All the above power quality indicators are inbuilt in MTX 4.5
Matrix Release System Architecture with Supplementary Modules
UW-MTX3.5EC
R
e
l
ayM
o
d
ul
e D
i
gi
t
alI
/
O M
o
d
u
le A
n
a
lo
gO
u
t
pu
t
Mo
du
l
e Z
S
I
Mod
u
l
e
UW-MTX4.5
?
Matrix Modules Architecture
? P
o
we
r
Su
pp
l
yMo
d
u
le
E
L
Mo
du
l
e R
E
FM
o
du
l
e T
C
SM
od
u
l
e T
MM
o
du
l
e
50
51
External Addon modules with microcontroller
Main Processor Connector

(DSP Core) Comm Modules
Zigbee
Profibus
PC-HMI
Driver
Flux Shift
Test Kit Modbus
RS485-Port
RYB & N
Current
Processing CAN Release
CAN bus CAN bus Display AIO
Driver
Module
CAN bus
Matrix CAN Architecture
REF
Internal EL Module
Module
CAN bus
Power Supply
Test
PS Configurator
Module Module
Voltage
Power Supply
Relays ZSI Module
Voltage Query
Processing Button
Trip LEDs
Digital I / O Temperature
Module Module
Modbus
TCS Module
Module
CAN bus
Matrix Modules 52
M
a
t
r
i
xPr
o
te
ct
i
onr
e
le
a
se
s
su
p
pl
eme
n
t
ar
yM
od
u
l
es
UW-MTX 3.5/4.5 releases are backed up by different supplementary modules to enhance the functionality of the
Protection & Control Unit to provide customer more advance and complete system protection.
Dip switches for

Node Address
O/P LEDS
Test LED
Power ON LED
Test Button for Communication LED
Module Testing
Maintenance LED
Relay O/Ps (Only Factory Testing)
(Change-over)
Relay O/Ps (NO Contacts)
Port for RJ45 Cable

Connection
Matrix Modules can be looped with

another module using RJ45 modular
connectors ensuring reliable and error-
free communication, supporting
unique CAN bus protocol.
Self Diagnostic Test:

All the modules (Except PS Module) are having self diagnostics test button provided on the front facia. Self test
of the supplementary module can be performed by removing the CAN communication connection of the P&C
unit with the PS module and 24V DC supply connected. (which is looped with the supplementary modules)
After test RED led indicates module is not healthy and GREEN indicates module is healthy.
53 Matrix Modules
R
E
L
AY
MO
D
UL
E
Relay module helps in remote annunciation, interlocking and load management of the system. Relay module consists
of four configurable O/Ps (2NO & 2 Changeover) which can be programmed through the release on any of the
following protection:
i. Overload vii. Phase sequence

ii. Short circuit viii. Under voltage
iii. Instantaneous ix. Over voltage
iv. Earth fault x. Under frequency
v. Neutral overload xi. MD (Active)
vi. Reverse power xii. Breaker operation
Each of the above protection can be programmed for “Trip” mode or

“Alarm” mode (Breaker operation can be programmed for breaker
ON or breaker OFF mode).
Relay module can also be used for switching off the non-critical loads
during the Overload condition so as to prevent the complete
shutdown of the system.
Four relay modules can be looped together to one release at a time.
Each relay module node address can be set using the dip switches on
the module.
R
e
l
ayo
ut
p
ut R
a
ti
ngc
o
nt
a
ct
R
e
l
ay a
s
si
gn
en (
d
i 4
co
nt
ac
t
sp
er
m
o
d
ul
e M
at
r
ixu
n
it r
e
la
ymo
du
l
e)
Relay 1 70-73 240VAC/24V DC, 6A

Relay 2 80-83 240VAC/24V DC, 6A
Relay 3 90-93 240VAC/24V DC, 6A
Relay 4 A0-A3 240VAC/24V DC, 6A
CAN-H
CAN-L
?
AS+
AS-
CAN COMMUNICATION BUS
SIC INTER CONNECTION
RJ 45 CABLE
OP1 OP2 OP3 OP4 OP1 OP2 OP3 OP4 OP1 OP2 OP3 OP4 OP1 OP2 OP3 OP4
4 RELAY O/PS 4 RELAY O/PS 4 RELAY O/PS 4 RELAY O/PS
Matrix Modules 54
R
E
S
TR
I
CT
ED
E
AR
T
HF
A
UL
T(
R
EF)
MOD
U
L
E
REF protection is usually applied for star winding of Transformer & Generator. Special protection class CTs i.e. Class
PS CTs are to be used for achieving the protection. Protection works on differential principle.
REF protection is used to detect and to trip the breaker in the selected zone only i.e. secondary winding of the
transformer/generator.
P1 T1 P2
R
mer
Sec of X /
Generator
winding P1 T5 P2
P1 T2 P2
P1 T3 P2
P1 Ir+Iy+Ib+In Id=0 Trip command to

T4 REF VCB at Primary side
P2 or Generator Relay
Ir+Iy+Ib+In Ir+Iy+Ib+In
If transformer star node is further used as a neutral in the system, the 5th CT (T5) should be used to avoid the nuisance
tripping during the unbalance condition.
During the unbalanced load condition the unbalanced current will flow back through neutral. As the direction of the neutral current is in
opposite direction as that of phases, the REF relay will not give nuisance tripping on current unbalance.
In absence of the 5th CT, the breaker will not be able to sense the unbalance condition flowing through the neutral and relay may give trip
command.
55 Matrix Modules
REF Zone
mer
HT relay ∆-Y X
F1 F2
CB ACB
(Ir+Ly+Ib+In-If)*r
REF
Trip command
to HT Relay Id=If*r
If1
If2
r = ct ratio
Id = deflection current
If1 = fault current @ F1
If2 = Fault current @ F2
Case 1. EF inside the restricted zone (F1)

During EF within the zone, current flows back to Xmer star point through neutral sensing CT. The REF
module will give trip command to the breaker depending on pickup value.
Case 2. EF outside the restricted zone (F2)

For EF outside the zone, fault current flows through phase CT & neutral CT in opposite direction
preventing the nuisance tripping from REF.
Matrix Modules 56
A
N
AL
O
GO
UT
P
UT
(
AO
)M
OD
U
L
E
Analog module can be seen as metering option to other panel display
meters.
Four different outputs can be configured for voltage metering or current
metering with analog signal output in range of 4-20mA to which analog
ammeter and voltmeter can be connected.
4mA corresponds to zero current and voltage while 20mA corresponds
to 1.5 times the set I-frame value of current or 1.5 times set Vn value in
Matrix release.
AO module communicates on CAN bus protocol with the Matrix
Protection and control Unit.
CAN-H
CAN-L
Current
AS+
I1 : 430A
I2 : 430A
AS-
I3 : 430A
IP1 IP2 IP3 IP4 COM

RJ 45 CABLE
?
AO1 AO2 AO3 AO4
4 ANALOG O/PS
57 Matrix Modules
T
E
MP
E
RA
T
UR
E
(
TM
)M
OD
U
L
E
Overheating of the Bus-bar can reduce the life of the
insulation sleeves, Bus-bar / cables & even Breakers. Periodic
loading conditions can cause the metal to heat and cool
continuously resulting in the deterioration of the Bus-bar
material and loosening of the joints. This becomes even
more critical in case if Bus-bars consist of metals of different
heat coefficient.
C
a
u
se
s
of
ov
er
h
ea
ti
ng
:
Any of the following reasons can lead to heat generation at
the breaker terminal
i. Improper termination
ii. Improper Bus-bar design
iii. Loosen Joints
iv. De-rating not considered while selection of breaker
v. Eddy currents
S
p
ec
i
f
ic
at
i
on
s:
i. Pick up (Tp) - 85OC to 115OC
ii. Pre alarm - 0.5Tp to 0.95Tp in the steps of 0.05Tp
iii. Delay - 0 Min to 15 Mins in Steps of 1 Min (It delays the tripping of the breaker by the set delay time.)
iv. Input supply-24V DC (Directly at Module Terminals)
Temperature Module senses the real time temperature at the Cradle terminals and displays on the Matrix
release screen. TM module can be used to give alarm on the release or to trip the breaker with the temperature
pickup range from 85oC to 115oC, which can be configured through Matrix release.
The module is to be fitted on the Breaker and is a factory fitted option.
Temperature
Phase1 : 45OC
Phase2 : 47OC
Phase3 : 50OC
CAN-H
} } T1-T4
connection to breaker terminals
CAN-L AS+
AS-
CAN L
? AS+ CAN H
AS-
AS+ : Auxiliary 24V DC

AS- : Ground
CAN- H : CAN-High
CAN- L : CAN-Low
Matrix Modules 58
ZSI (Zone Selective Interlocking)

Using the Zone Selective Interlocking feature of the Matrix
releases, intelligence can be imparted into the electrical system
for the quick trip and isolation of the fault element of the system.
For ZSI feature, P&C units are hardwired as shown and they
communicate with each other through restraining signals. In ZSI
active mode, time delays in short circuit and earth fault are set
progressively higher towards the main incomer ACB.
In the given diagram, ACB 1 has the highest delay of 400ms for
short circuit. ACB 2 and ACB 3 are having delays 200ms, 100ms
respectively. For fault at Y, ACB3 will send restraining signal to
ACBs 1 & 2 and hence pre-set delays are honored. ACB 3 will trip
in 100ms and the fault will be cleared.
ACB 2, ACB 3 will remain closed, for faults at immediate
locations like X, there will be no restraining signal from feeder
breakers ACB 2, ACB 3 and hence ACB1 will Issue Trip command
immediately instead of Pre-set 400ms delay.
MTX Releases of OMEGA provides two type of options for
Sout Gout ACB 1
achieving Zone Selective Interlocking (ZSI) - ZSI S. C. Time
MODULE 1 Delay 400 ms
Sin Gin
1 .ZSIth rou gh M TX 1G i& M TX1.5G i
MTX1Gi & MTX1.5Gi are having inbuilt ZSI. Wiring for ZSI to be
done directly through SICs of ZSI (available at SIC Block-6 &
X
marked in yellow color). When MTX1Gi /1.5Gi Releases are used
in Downstream with an External Matrix ZSI module in Upstream,
an additional 24V DC supply needs to be connected to the SIC
at AS+/AS- of SIC Block 6. ZSI
Sout Gout ACB 2
S. C. Time
ZSI Wiring Cable Specification and compatibility with other MODULE 2 Delay 200 ms
Sin Gin
Realeases & ZSI Module is mentioned in below Tables.
2 .ZS Ith rou gh E x

t
erna lM o dule w ithM TX3 .
5 & ab o ve
ZSI Module for Releases MTX3.5 & above is available as an acce-
-ssory. This module provides optional upgrade to Zone Selective
Interlocking (ZSI).
Sout Gout ACB 3
ZSI feature provides- ZSI S. C. Time
MODULE 3
• Discrimination for Short-Circuit & Earth Fault protection Sin Gin Delay 100 ms
• CAN Bus protocol for communication in ZSI Module Y
• Support 20 downstream & 3 upstream Omega ACB
• Provision for self-diagnostics Test
Note :
Input supply 24V DC, Need to be applied directly on Terminals of ZSI Module
ZSI Cable Specification ZSI Compatibility Chart

m
Description PVC sheathed shielded twisted pair wire Releases in Upstream

n
MTX Releases MTX3.5 & above

a
MTX1Gi MTX1.5Gi
e
Size 7/0.2 tinned copper with ZSI Module

e
w
s
i
n r
a
s
t
MTX1Gi üü *
s
Braided tinned copper ID: 4.6 max

e
Shield
o
e
D
R
MTX1.5Gi üü *
l
Impedance Approx. 76 Ohm/km at 200 MHZ

MTX3.5 & above
No. of Twists Approx. 11 twists / ft. üü ü
with ZSI Module
ü Compatible
* Compatible-Additional External 24V DC Supply to be provided
GO1
GO2
M-G
SO1
SO2
AS+
C-G
C-H
GI1
GI2
AS-
D+
C-L
V1
SI2
SI1
V2
V3
V0
D-
at AS+/AS- of SIC Block-6
ZSI Contacts on SIC Block-6 (Marked in Yellow)

59 Matrix Modules
E
A
RT
H
LE
A
KA
GE
(
E
L)
MOD
U
L
E
In industrial installations, the current leakage can happen to earth because of
the following main reasons:
i) Current leakage through phase to earth insulations
ii) Leakage of current through phase to earth leakage capacitance
Due to the high insulation resistance the leakage current magnitude remains
low in terms of milliamps or micro amps. Assuming that the phase-to-earth
insulation resistance in an LV network is just 1 Mega-ohm(*), then the leakage
current to earth will be (240V/1 Mega-ohm) 240 microamperes. But, generally
the phase-to-earth insulation resistance would be much higher than just
1Mega-ohm, normally a few tens or even hundreds of Mega-ohms. Thus, the
leakage current to earth will be a further fraction of the micro-ampere or even
nano-amperes. As human body’s sensible current is more than 1 milli-ampere,
this remains un-sensed by a human being coming in contact with the earthed
frame of an LV electrical installation.
Any leakage current above 300mA can result into fire in electric installations. In Industrial areas especially in mining
application the earth leakage protection becomes critical for the fire safety.
Omega Matrix Earth Leakage module has Earth leakage current monitoring range of 300mA to 30A. The EL module
communicates on CAN bus with the Matrix releases which can be set in Alarm, Trip or “Both”mode.
S
o
me
mo
r
e
fe
at
u
re
so
f
E
Lmo
d
ul
e:
• "NO" contact for external indications (24V DC/240V AC, 6A)
• Standalone module
• Dip switches for configuring pickup and delay settings
• Self-diagnostic check for module healthiness check
*As per Indian Electricity rule, 1956, Rule No. 48(ii) For Medium & Low Voltage Installations, Voltage at a pressure of 500 V applied
between each live conductor and earth for a period of one minute, the insulation resistance of medium and low voltage installations shall
be at least 1 Mega ohm.
Matrix Modules 60
D
I
GI
TA
LI
NP
UT
O
UT
P
UT
(
DI
O)
MOD
U
L
E
Matrix DIO module is provided with 4 digital inputs and 4 digital
outputs for the implementation of various Boolean logic
equations into the system.
Some features of DIO module
• Up to 4 DIO modules can be looped together to one MATRIX
release
• Dip switches on the Module facia for setting the node address
• 16 different logic equations can be assigned
• Self-diagnostic test provision
C
o
nt
a
ct
Ra
t
in
g
s
I
np
ut
c
on
ta
c
t
s 24V DC or 240V AC
O
u
t
pu
t
Co
nt
a
ct
s24V DC or 240V AC, 6A (resistive load)
TRIP CIRCUIT SUPERVISION (TCS) MODULE

TCS module of Matrix Releases continuously monitors the
healthiness of the shunt trip coil irrespective of the breaker
operational position. Protection can be set in both, trip or alarm
mode in the release unit.
• Detects circuit breakage, contact degeneration in
connections, resistance increase in wires, contacts and coils of
the supervised shunt release
• Complete range of rated voltage (24-415V) either AC or DC
• Standalone module
• Self-diagnostic test provision
POWER SUPPLY (PS) MODULE

PS module is used to power ON other supplementary modules of
OMEGA Matrix release family as well as to communicate on the
CAN bus through RJ45 shielded cable.
S
p
ec
i
f
ic
at
i
on
s A
C D
C
Input 85-265V 125-300V
Output 1* - 200mA @ 24V DC
Output 2 - 650mA @ 24V DC
Note : For VA burden details of modules & optimal usage of PS modules refer Matrix User’s manual
first
* For using Output 1, Output 2 should be loaded
61 Matrix Communication Protocols
Modbus: Monitoring function:
Modbus Module is used for the Configuration, 1) Metering Data – Voltage, Current, Power, Energy,
Monitoring and Control of Matrix releases and Power Factor, Online Module Status
its supplementary modules. 2) Status Data – Alarm & Trip Status, Digital Input
It offers Client/Server communication in RTU mode. Output Module & Relay Module Status
3) Record Data – Trip Records, Event Records,
Maintenance Records
Configuration function:
1) Unit Settings Control function:
2) System Settings
1) Commands for Set group Change, Restore Factory
3) Protection Settings Group 1 Defaults, Clear Maximum Demand
4) Protection Settings Group 2 2) Maximum Current value, Maximum Voltage Value
5) Module Settings and Energy, Open and Close Circuit
3) Breaker, Maintenance Acknowledgement and
Earth Fault (EF) test
DATA+
DATA- SERIAL CABLE

RS232 to RS485
CONVERTER
VS +
SHIELD GND
PS MODULE
M-G C-G D+ D- V1 V2 V3 V0 AS+ AS- SIC Termination

P
C
HM
I
Pre-wired Connections inside breaker
Shielded Co-axial 2 core Cable
MODBUS
C
O
MMS
T
AT
U
STE
S
T
CONFIGURATOR MODBUS
METERING MODULE
SELF-TEST SWITCH
For factory use only
STATUS LED
Blinks AMBER for 5s when Module is connected indicating self-test.
Blinks GREEN continuously to indicate healthy POWER ON.
Glows RED if unhealthy / self-test fails.
COMMUNICATION LED
Blinks RED during communication data transfer
Matrix Communication Protocols 62
Profibus:
Profibus Module supports PROFIBUS DP V0 slave protocol. This module communicates with PROFIBUS Class 1 and/or
Class 2 Master.
GSD file should be used/loaded in PROFIBUS master for understanding the device functions. Network termination
switch is provided at the rear end of the module. Thus this module can be used as end node in the network.
It communicates on baud-rates 9.6Kbps, 19.2Kbps, 45.45Kbps, 93.75Kbps, 187.5Kbps, 500Kbps, 1.5Mbps,

3Mbps, 6Mbps, 12Mbps. It automatically detects the baud-rate selected by PROFIBUS master for communication.
PROFIBUS module is used to monitor and configure critical status parameters of Matrix Release like Pick-up, Alarm
and Trip status.
DATA+ PROFIBUS CABLE
DATA-
SHIELD
PS MODULE
M-G C-G D+ D- V1 V2 V3 V0 AS+ AS- SIC Termination P

R
OF
I
BU
SM
A
S
TE
R
or
PL
C
Pre-wired Connections inside breaker
Shielded Co-axial 2 core Cable
PROFIBUS
PROFIBUS
C
O
MMS
T
AT
U
STE
S
T
CONFIGURATOR
CONFIGURATOR PROFIBUS
METERING
METERING MODULE
MODULE
SELF-TEST SWITCH
STATUS LED
COMMUNICATION LED
63 Matrix Communication Protocols
Zigbee:
Our innovative Matrix releases are designed to let consultants & system designers help their customers & end-users
gain greater control of, and improve their everyday business & industrial processes by means of “ZigBee wireless
communication” capability.
UW-MTX3.5/3.5EC/4.5 provides Wireless Communication using ZigBee protocol formulated under IEEE 802.15.4
standard for Wireless Personal Area Network (WPANs). Zigbee operates in ISM radio bands of 2.4GHz.
The Communication range is 200m Line Of Sight (LOS) with over the air data rates upto 250 Kbps. Zigbee module is
used for Monitoring parameters of Matrix releases and its supplementary modules.
Monitoring function:
1) Metering Data – Voltage, Current, Power, Energy, Power Factor, Online Module Status
2) Status Data – Alarm & Trip Status, Digital Input Output Module & Relay Module Status
3) Record Data – Trip Records, Event Records, Maintenance Records
ZIGBEE
CO-ORDINATOR
POWER USB CABLE
LED
(OPTIONAL)
NETWORK
LED
PS MODULE
PC HMI
C
O
MMS
T
AT
U
STE
S
T
ZIGBEE
PROFIBUS
ZIGBEE
SELF-TEST
u SWITCH
CONFIGURATOR
CONFIGURATOR
METERING
METERING MODULE
MODULE
STATUS
u LED
COMMUNICATION
u LED
Glows RED when not in network.
Note:
1) It is necessary to first switch on the Co-ordinator module and form a network. Co-ordinator Module can be
directly plugged in the PC USB port or USB cable can be used.
2) Power LED on Co-ordinator Module will glow GREEN when connected to the port. Network LED on Co-ordinator
module will glow GREEN when it forms a network.
3) Zigbee Module should be now inserted in the Matrix P&C unit .
Smart Configurator 64
Smart Configurator:
UW-MTX3.5/3.5EC/4.5 has an optional Smart Configurator Module which is used for easy parameterisation of the
release. In large electrical installations, where many ACBs are in use; one can copy the release protection parameters
setting on smart card and then copy the parameters on various releases. Smart Configurator Module in MTX releases
with its ease of use can reduce the gestation period of electrical installation.
Smart Configurator works on the principle of RF interface at 106kbps between the module and the Smart Card.
The following operations can be performed on the Smart Card:
1) Write File: Copy files from the release to the card
2) Read File: Copy files from the card to the release
3) Delete File: Delete selected file from the card
4) Format Card: Delete all the files from the card and format it
PS MODULE
INSERT
u CARD HERE
MODBUS MODULE
(Card goes inside the module partially. Check the Comm LED to see
C
O
MMS
T
AT
U
STE
S
T whether the card is detected.)
CONFIGURATOR
CONFIGURATOR CONFIGURATOR
METERING
METERING MODULE
MODULE
SELF-TEST
u SWITCH
For factory use only.
STATUS
u LED
COMMUNICATION
u LED
Glows RED when not in network.
Blinks RED during communication data transfer.
65 Fault Trip Diagnostic
Trip Oscillograph
MTX 4.5 gives user the unique advantage of analyzing the post fault waveforms of the system. After the fault, the
system waveform gets captured in the release with the trip timing and the waveform deformation of voltage and
current of the individual phases. The data remain stored in the memory of the release so as to empower the user to
check the speed and the correctness of the protection system, as well for further power system analysis.
Some of the unique points of the MTX4.5 Trip Oscillograph are:
• 300ms record with 10 cycles before and 5 cycles after the trip/pickup of fault
• 15 cycle record useful to monitor and analyze the current and voltage disturbances
• 4x zoom
18:23
Current
In
0.6 247.8952, 0.5266
18:23
Current
In
0.6
0.4
247.8952, 0.5266
0.4
0.2 0.2
0
-0.2 0
-0.4
-0.2
150 200
Time (ms)
-0.4
?
150 200
Time (ms)
MTX4.5
Menu Navigation Overview

for UW-MTX 3.5/3.5EC/3.5H
Current
I1 : 800A
I2 : 800A
I3 : 800A
Settings View Records Metering IO Status Active Modules
Config. Mode View Mode Trip Record Current ACB status

Event Record Voltage FSD status
(Password protected) Maintenance Frequency Digital I/O 1
Power Factor Digital I/O 2
MTX Unit Power Digital I/O 3
Configurator Energy Digital I/O 4
Modbus Max Demand Relay 1
Temperature Relay 2
Relay 3
Relay 4
System Settings Unit Settings Protection Module Settings Restore Settings Default Settings
(Password protected)
Frequency Date & time Set Group 1 Digital I/Os Maint OP

I-frame Communication Set Group 2 Relay Clear MD
In Event Recorder Temperature Change Set Group
Ue voltage Sign Convention Modbus Factory Setting
Maint Period Max Demand Configurator Clear Max. I
Maintenance Setting P/W Analog O/P Clear Max. V
Incoming Commands P/W ZSI Clear Energies
Poles Contrast TCS
Ph seq Auto Set GRP Earth Leakage
Maintenance ZIG-Bee
Day light Saving Profibus
Restricted EF
Current Protection Voltage Protection Frequency Protection Power Protection Other Protection
Overload Under Voltage Under Freq Rev Power MD Active

Short circuit Over Voltage Over Freq Leading PF MD Reactive
Directional SC Voltage Unbal Lagging PF MD Apparent
Instantaneous Residual Volt Phase Sequence
Earth Fault Bkr failure
Ntrl Overload
Restricted EF
Earth Leakage
Under Current
Current Unbal
67 SmartComm Integrated Solutions
• SmartComm is a state-of-the-art SCADA-based unified software platform for device communication, integration,
data acquisition, data management, monitoring & control and preemptive and predictive data analysis.
• Omega ACBs can be integrated with smartcomm.
• SmartComm supports a wide range of devices and protocols. It can expand its functionality to address the
growing requirements of the installation
SmartComm Integrated Solutions 68
& Control
Monitoring
U s nag
Ma
e r em
s
stic
gno
cy
e
Dia
Gr
nt
n
ap
h ic da
s d un
Re

External Interfac
es Commu
nication

Sm
a
rt
Co
mm
Data
n
r atio Ap p
licat
igu
C on f i on
O
m
e
ga
A
CB
s-
I
nt
eg
r
at
i
onw
i
t
hSm
a
r
t
Co
mm
b
ri
ng
sa
h
os
t
of
be
ne
f
i
t
s:
• Omega ACBs integrated with SmartComm enable users to perform various configuration, monitoring and
measurement tasks remotely
• Real-time communication for monitoring, control and diagnostics. The system also provides facility of
alarms, event-alerts and acknowledgements
• Enables user to get immediate reports and swiftly initiate corrective action, if required
• Remotely control and monitor the circuit breaker from centralized location.
• Get 'trip info' details such as cause of tripping, date and time stamping of tripping and fault event history.
• Monitor ACB terminal temperature along with real-time trending and Over-temperature annunciation.
• Undertake time-based harmonic monitoring and analysis for the complete plant.
• Implementing dual set group for intelligent selection of protection settings based on Real Time Clock.
• Plan and schedule maintenance to reduce energy and operation cost.
• View instantaneous parameters like voltage, current, power factor etc. at a single location.
• SmartComm can be configured to e-mail reports and SMS critical alerts.
• Communication through multiple protocols and drivers like Modbus TCP/IP, Modbus RTU, BACnet.
Accessories
Accessories 70
Accessories
Breaker Accessories Cradle Accessories
}Auxiliary Contact Block }Electrical Position Indication (EPI)

}Shunt Release (SR) }Door-Interlock
}Closing Release (CR) }Door-Racking Interlock
}Under-Voltage Release (UVR) }Locking in all Positions
}Electrical Charging Device (ECD) }Locking in Disconnected Position
}Operation Counter }Safety Shutter
}Micro-switchesfor electrical indications: }Arc-Shield
ü
Common fault indication
}Rating Error-Preventer
ü
Under-Voltage release trip indication
ü
Shunt release trip indication
ü
Spring charging indication
ü
Ready to close indication
}Locking ‘OFF’ Button (LOB)
}Shroud for ON-OFF Button

Miscellaneous
}Breaker Maintenance Cover
}Ingress Protection Cover
}Mechanical Interlock
}Terminal Adaptors
}Neutral Configurator
}External Neutral CTs

71 Accessories
Breaker Accessories:
Modularity, the key design aspect of OMEGA ACBs facilitates the quick fixing & removal of several breaker mounted
accessories such as CR, SR, UVR, Auxiliary contact blocks & various indicating micro-switches. These accessories are
located on the front top-side of breaker mechanism & have specified positions.
Auxiliary Contact Under-voltage Closing Shunt
Block Release Release Release
Common
1 2 3 4 5 Fault Indication
6
Under-voltage
Release
Controller
Under-voltage Operation
Trip Indication Shunt Trip Counter
Indication
1) Auxiliary Contact Block: Auxiliary Contact Block contains the change-

over switch contacts in combination of 4 units of 1NO+1NC each. Auxiliary
contact block reflects the breaker ON/OFF state in control circuit.
Operational voltage (Ue) upto 24V 110V 220/230V 400V

In (AC-12) at 50/60 Hz 10A 10A 10A 10A
In (AC-15) at 50/60 Hz 6A 6A 6A 4A
Operational voltage (Ue) 24V 40V 110V 220V

In (DC-12) 10A 8A 3.5A 1A
In (DC-13) 10A 4A 1.2A 0.4A
2) Shunt Release (SR): Shunt Release when energized opens the breaker
instantaneously. Omega ACBs offer general purpose Shunt Release which can
reliably trip the Circuit Breaker through external trip command. C2
C1 TCS
Operational voltage (Ue) Power consumption Operating range

110, 240, 415V AC at 50/60Hz 200VA for 0.5 sec 70-110% of Ue
24, 30, 48, 60, 110, 125, 220, 250V DC 200W for 0.5 sec 70-110% of Ue
3) Closing Release (CR): Closing Release remotely closes the Circuit Breaker
if the spring mechanism is already charged. Closing Releases in Omega
Air-circuit breakers come with inbuilt Electrical anti-pumping feature. Inbuilt A1 A2
electrical anti-pumping feature prevents auto-reclosing of Circuit Breaker on

faults. Anti-pumping relay cancels the persistent closing signal after successful
completion of the closing operation.

110, 240, 415V AC at 50/60Hz 200VA for 0.5 sec 85-110% of Ue
24, 30, 48, 60, 110, 125, 220, 250V DC 200W for 0.5 sec 85-110% of Ue
Accessories 72
4) Under-voltage Release + Delay Module (UVR): The Under-

voltage Release causes the Circuit Breaker to open if the operational voltage
falls to a value between 35% and 70% of its rated voltage or not applied.
UV Release mechanically locks the closing of breaker & it makes it impossible
to close the Circuit breaker, either manually or electrically. The Circuit breaker
can be closed with operation voltage of 85-110% of its rated value.
UV Release can be used for monitoring the voltage in the primary (power D2
circuit) or secondary (control circuits) circuits or can be used for electrical D1
interlocking scheme (for DG synchronization, paralleling of transformers etc).

In order to avoid the nuisance tripping of the circuit breaker during short
voltage dips, UV release comes with the UV-delay module. Operation of UVR
can be delayed between 0 to 5 secs. in steps of 0-1-3-5 sec.
T
y
p
e N o r
m a lVo lt
ag e S hort
-t
ime Po w e
r
O pe rati
ng
Cons
um ptio nL im i
t
UVR 110, 220, 240, 415 V AC
(Delay Setting-0,1, 200VA max, 3s
50Hz / 60Hz 85 - 110%
3 & 5 sec) 24, 30, 48, 110, 220 V DC 200W max, 3s
5) Electrical Charging Device (ECD): Electrical Charging Device

automatically charges the closing springs of the circuit breaker operating
mechanism. After Circuit Breaker closing operation, the geared motor
immediately recharges the closing spring. Thus instantaneous re-closing of
the circuit breaker is possible following opening operation. The closing springs
can also be charged manually (using the spring-mechanism charging handle)
in the event of an auxiliary power supply failure or during maintenance work.

110, 240, 415V AC at 50/60Hz 300VA for 1 sec 85-110% of Ue
24, 30, 48, 60, 110, 220, 250V DC 300W for 1 sec 85-110% of Ue
6) Operation Counter: The Operation Counter indicates the number of

operating cycles the Circuit breaker has been subjected to and it is visible on the
Circuit breaker front-facia. It is compatible with manual and electrical control
functions. Counter readings serve as a guide for maintenance & inspection.
7) Micro-switches for electrical indications:

a. Common Fault Indication (CFI): CFI provides the
electrical indication of circuit breaker tripping due to
operation of protection & control unit.
b. Under-Voltage Release Trip Indication: Under-voltage
Release Trip Indication micro-switch provides electrical
indication of circuit breaker tripping with the operation of
under-voltage release.
c. Shunt Release Trip Indication: Shunt Release Trip
Indication micro-switch provides electrical indication of circuit breaker tripping with operation of shunt
release.
d. Spring Charging Indication: Spring Charging Indication micro-switch provides the electrical indication
whether main mechanism spring is charged or not.
e. Ready-To-Close Indication (RTC): RTC takes into account all the safety parameters that are part of the
control & monitoring system of electrical installation. OMEGA RTC allows the circuit breaker to close only if
following conditions are met:
ü
Main spring is charged ü
All Arc-chutes are properly placed
ü
Circuit Breaker is OFF ü
Mechanical trip indication lever on release is
ü
Shunt release is de-energized reset
ü
Under-Voltage release is energized ü
Racking shutter is closed
73 Accessories
8) Locking ‘OFF’ Button (LOB): LOB locks the breaker in OFF position by continuously pressing the OFF
push button. Lock defeats all the positive closing signals (mechanical or electrical) coming to the breaker and
thus prevents the nuisance closing of the breaker. Locking ‘OFF’ button (LOB) can be implemented using C-Type /
R-Type of locks. The locks are designed in such a way that the keys cannot be removed out till the breaker is
locked (OFF button pressed). Locking of the breaker in OFF position ensures safety of the maintenance person
working on downstream equipment. Locking ‘OFF’ button (LOB) can be used to
design the interlocking schemes with other devices in the system.
9) Shroud for ON-OFF Button: Transparent shroud blocks the access to the
ON/OFF push-buttons used to open and close the breaker. It prevents inadvertent or
unauthorized operation of the ON or OFF button. It’s possible to independently lock
the ON/OFF push button with the help of ON-OFF button shroud & mechanical lock. It
can be pad-locked with lock hasp of 6mm diameter.
Cradle Accessories:
1) Electrical Position Indication (EPI): Secondary Isolating Contact (SIC) blocks on ACB cradle assembly
facilitates the electrical indication for the exact position of the breaker within the cradle. 3 SIC contacts
electrically indicates the Connected / Test / Disconnected positions of breaker.
2) Door-interlock: Door-interlock inhibits the opening of door if ACB is in

Test or Service position. Door-interlock can be mounted on either side of
the cradle (LHS or RHS).
3) Door-racking interlock: Door-racking interlock prevents the

racking-in operation of the breaker if panel door is open.
4) Racking Shutter Pad-lock: Racking Shutter Pad-lock inhibits the access to the racking mechanism such
that racking handle cannot be inserted to rack-in/rack-out the breaker. Racking Shutter Pad-lock is an inbuilt
feature with Omega ACBs. It can be pad-locked with lock hasp of 6mm diameter.
5) Safety Locks: Any of C-Type, R-Type locks can be used for locking the ACB in "Any position" / "Isolated
position" & locking "OFF" push button, for interlocking with other electrical devices in the control scheme of the
system.
C-Type R-Type
Accessories 74
6) Locking in Disconnected position: Locking in Isolated/Disconnected position inhibits the undesirable

racking-in operation of the breaker from the isolated position. Locking in isolated position can be implemented
using C-Type, R-Type locks. Locking of the breaker in disconnected position ensures safety of the maintenance
person working on downstream equipment. The locks are designed in such a way that
the keys cannot be removed out till the breaker is locked, at the same time the breaker cannot be locked
in “Service/Connected” or “Test” positions. Locking in Disconnected position can be used to design the
interlocking schemes with other devices in the system.
7) Locking in all positions: Locking in all positions facilitates the locking of breaker in Connected/Test or
isolated positions. Locking in all positions can be implemented using C-Type, R-Type locks.
8) Safety Shutter: The fixed part (cradle) of withdrawable Circuit Breaker contains safety shutters for
preventing inadvertent access to live terminals of Circuit Breaker when
breaker is withdrawn from the cradle. Safety shutters can be locked in
closed position using pad-lock devices.
9) Arc-shield: Arc-shield helps in reducing the vertical clearance between
two ACBs in vertical tier panels from 300mm to mere 45mm.* Arc-shield
facilitates in compact design of switchboards.
10) Rating Error-Preventer: Rating Error-Preventer ensures that the
breaker of proper rating goes with the cradle of corresponding rating. It is
made up of two sub-assemblies one on the cradle and other one on the
breaker. Rating Error-Preventer offers distinct combination for a particular
breaking capacity version within a particular rating of the breaker. Rating
Error-Preventer comes as an inbuilt feature with Omega ACBs.
Miscellaneous Accessories:
1) ACB Maintenance Cover: Using Cover, panel door can be covered during maintenance at site to prevent
the entry of dust or foreign material in the panel enclosure and cradle. The same can be fitted on the bezel
without any tool and is common for fix and draw-out version of OMEGA ACB.
PANEL MAINTE
PANEL
NANCE COVER
MAINT PANEL
ENANC MA
E COVER INTENA
NCE CO
VER
ELECTRIC
AL HA
BEWARE O ZARD
ELECTRIC ELECTRICAL F ELECTRICAL
AL H HAZARD
BEWARE OAZARD PERSONAL SHOCK.
INJURY O BEWARE
ELECTRCI
F SCALDING
BURN
R ELECTRICAL OF
PERSONA ALSH OCK. MAY BE CAUSED SHOCK.
PERSONAL INJURY
L INJURY
SCALDINGBU OR SCALDING BURNOR
MAY BE CA RN MAY BE CAUSED
USED
2
)
In
gr
e
ss
Pr
o
te
ct
i
on
Co
v
e
r:
A transparent safety cover mounted on the door-sealing frame on panel door
increases the Ingress Protection (IP) of the ACB from IP53 to IP54. Safety cover can be mounted in Left hinge /
Right hinge combinations.
* In case of Temperature Module mounted on the Cradle this dimension should be 70mm.
75 Accessories
3) Mechanical Interlock : Mechanical Interlock is used for interlocking breakers as per the desired control
scheme. It can interlock up to three Omega ACBs of Fixed/Draw-out/Mixed version. The breakers can be
interlocked in Vertical or Horizontal configuration.
Cable length: 2/3/5 meter, minimum radius at cable bend: 70mm
Possible mounting arrangements:
Type of Interlock Typical Circuit Interlocks Possible Schematic Diagram
Two Incomers A B
(2 I/C)
G
Three Incomers A B C
(3 I/C)
G
Two Incomers &
One Standby A B C
(2 I/C + 1 S/B)
Two Incomers & A C

One BusCoupler B
(2 I/C +1 B/C)
O - Breaker Open I - Breaker Closed

Accessories 76
4) Terminal Adaptors:
OMEGA ACBs offer wide variety of terminal adaptors for both Fixed & Draw-out versions.
Terminal Adaptors facilitate ease of termination of both Copper & Aluminium busbars.
Terminal Adaptors Draw-out version :

for
Frame-1 : 400-2000A
15
Termination side dimensions (T)

Hole No. of C
Thickness T
distance holes
19
27 15 2
65
27
Frame size Configuration Height
Fr-1 400-2000A Vertical / Horizontal 65
All dimensions are in mm

For ordering cat nos please refer page no.80
20
Frame-1 : 2500A, Frame-2 : 400-3200A,
T
e
r
mi
na
ti
ons
i
ded
i
men
s
i
on
s(
T
)
22
Hole distance Thickness No. of holes
27 20 3
27
98
F
r
a
mes
i
z
e C
o
nf
i
gu
ra
t
i
on H
e
i
gh
t
Fr-1 2500A Vertical 98
Fr-2 400 - 3200A Vertical / Horizontal 98 T

Frame-2 : 4000A
T
e
r
mi
na
ti
ons
i
ded
i
men
s
i
on
s(
T
)
T
Configuration Hole distance Thickness No. of holes
32
23 27
100
Horizontal 27 32 3
Vertical 27 20 5 20
F
r
a
mes
i
z
e C
o
nf
i
gu
ra
t
i
on H
e
i
gh
t/
Wi
dt
h
21
Fr-2 4000A Horizontal 100
27
150

T
77 Accessories
F
r
a
me3
:
40
0-
40
00
A 165
T
e
r
mi
na
ti
ons
i
ded
i
men
s
i
on
s(
T
)
Configuration Hole No. of T 15

distance Thickness holes
Horizontal 27 15 6 27
15
Vertical 27 15 4
H
o
r
i
zo
nt
a
l
15
F
r
a
mes
i
z
e C
o
nf
i
gu
ra
t
i
on H
e
i
gh
t/
Wi
dt
h
22
27
125

T
V
e
r
t
ic
a
l
165
F
r
a
me-
3:
50
00
A
T
e
r
mi
na
ti
ons
i
ded
i
men
s
i
on
s(
T
) 20
T
Configuration Hole No. of
Thickness holes
distance
27
15
Horizontal 27 20 6
H
o
r
i
zo
nt
a
l
Vertical 27 20 4
20
22
F
r
a
mes
i
z
e C
o
nf
i
gu
ra
t
i
on H
e
i
gh
t/
Wi
dt
h
27
125

T
V
e
r
t
ic
a
l
F
r
a
me-
3:
63
00
A
T
e
r
mi
na
ti
ons
i
ded
i
men
s
i
on
s(
T
) 20
27 20 5 21
27
150
F
r
a
mes
i
z
e C
o
nf
i
gu
ra
t
i
on H
e
i
gh
t
T
V
e
r
t
ic
a
l
Accessories 78
Terminal Adaptors Fixed Version :

for
Frame-1 : 400 - 2000A N/S
T
e
r
mi
na
ti
ons
i
ded
i
men
s
i
on
s(
T
)
27 15 2
F
r
a
mes
i
z
e C
o
nf
i
gu
ra
t
i
on W
i
dt
h
19 27 15
Fr-1 400 - 1600A Vertical / Horizontal 65 T
65
Frame-1 : 400 - 2000A H, & Frame-3 : 400 - 4000 H/V
T
e
r
mi
na
ti
ons
i
ded
i
men
s
i
on
s(
T
)
27 15 2
F
r
a
mes
i
z
e C
o
nf
i
gu
ra
t
i
on W
i
dt
h
Fr-1 S 2000A Vertical / Horizontal 65
19 27 15
Fr-1 H 400 - 2000A Vertical / Horizontal 65 T
Fr-3 H/V 400 - 4000A Vertical / Horizontal 65 65

79 Accessories
Frame-1 : 2500A S/H & Frame-3 6300A H/V
27 20 3
Frame size Configuration Width

27 T 20
23
Fr-1 S/H 2500A Vertical 100 T
Fr-3 H/V 6300A Vertical 100 100

Frame-2 : 400-2500A N/S

27 20 3
27 T 20
23
T
Frame size Configuration Width 100
Fr-2 N/S 400 - 2500A Vertical / Horizontal 100

Frame-2 : 3200 N & 400 - 4000A S/H

27 20 3
27 T 20
23
T
Frame size Configuration Width
100
Fr-2 H/V 400 - 4000A Vertical / Horizontal 100

Frame-3 : 5000A H/V

27 20 2
24 27 20
Frame size Configuration Width T
Fr-3 H/V 5000A Vertical / Horizontal 75 75
All dimensions are in mm | T: Termination side

D
r
a
wOu
t
Ve
r
si
on
F
r F
r
a
me1 F
r
a
me2 F
r
a
me3 Following table consists of the total nos of the
terminal adaptors required for each breaker
A4
00
A
-
20
00
A25
0
04
A0
0
A-
3
200
A40
0
0A4
0
0A
-
4
000
A50
0
0
A 6
3
00
A (Top & Bottom side included)
D/O Rating 3P 4P Orientation
l
c
a
c
400-2000A 6 8 any
t
Frame 1
n
76 A
Vertical 2500A 6 8 any
o
es
termination
z
400-3200A 6 8 any
i
s
r
recommended
Frame 2 4000A 6 8 Horizontal
i
o
r
Width : 65mm Width : 98mm Width : 100mm Width : 165mm Width : 165mm 4000A 6 8 Vertical
Vertical termination
recommended
o
CL60963OOOO CL60964OOOO CL60316OOOO CL60073OOOO CL60966OOOO 6 8 Horizontal

Accessories
4000-5000A
Frame 3 12 16 Vertical
es
6300A 12 16 Vertical
il H
a
c
Fix Rating 3P 4P Orientation
t
r
400-2000A 6 8 any
e
Frame 1
2500A 6 8 Vertical
V
Height : 65mm Height : 98mm Height : 150mm Height : 125mm Height : 125mm Height : 150mm Frame 2 400-4000A 6 8 any
CL60963OOOO CL60964OOOO CL60965OOOO CL60128OOOO (1EA) CL60067OOOO (1EA) CL60965OOOO (1EA) 12 16
400-4000A any
Frame 3
5000-6300A 12 16 Vertical
F
i
xVe
r
s
i
on
F
r F
r
a
me1 F
r
am
e2 F
r
a
me3
#
V
e
rN/
S H S/H N
/
SN *
/
S/
H H/
V
A4
0
0
A-
2
000
A 4
0
0
A-
2
000
A25
0
0
A40
0
A-
2
500
A40
0
A-
4
000
A40
0
A-
4
000
A 5
0
0
0A 6
3
0
0A
nl
a
t
Vertical
o
Vertical termination termination
z
i
recommended recommended
r
o
Width : 65 mm Width : 65 mm Width : 100 mm Width : 100 mm Width : 65 mm Width : 75 mm
CL60967OOOO CL60968OOOO CL60122OOOO CL60977OOOO CL90668OOOO (1EA) CL60982OOOO (1EA)
i
t
r
e
Vl H
a
c
Height : 65 mm Height : 65 mm Height : 100 mm Height : 100 mm Height : 100 mm Height : 65 mm Height : 75 mm Height : 100 mm
CL60967OOOO CL60968OOOO CL60976OOOO CL60122OOOO CL60977OOOO CCL90668OOOO (1EA) CL60982OOOO (1EA) CL90669OOOO (1EA)
*For 3200A N Version

# For 3200A & 4000A S Version
8
0
8
1Accessories
5) Neutral Configurator :
Neutral configurator helps in customization of Neutral Sequence or Phase Sequence at the Air Circuit Breaker end.
Neutral Configurator can be connected with the breaker On-site. It enables user to customize the phase sequence
at breaker end without any design modication required in panel. In case of standard phase sequence the output
of the Breaker CTs directly connected to the MTX Release with the help of Wire harness. When Neutral Configurator
is being used it will be connected to the MTX Release and harness wire will be connected to the other end of the
Neutral Configurator. It can be used irrespective of Breaker frame sizes, Ratings and MTX Release types. Neutral
configurator is compatible with 100%N systems only.
N
o
t
e:Wh
il
eNe
ut
r
aC
lon
fi
gu
ra
t
o
ri
sbe
in
gus
edf
or
i
nt
er
c
ha
ni
gn
gNe
u
t
ra
l
Po
le
wi
t
han
yot
h
er
Pol
e,
t
heC
T
so
fr
es
pec
ti
v
ePo
l
es
mus
t
al
s
obe
in
te
r
c
ha
ng
ed
.
T
he
ref
or
e
CTo
ft
he
old
Ne
u
tr
al
-
Pol
es
ho
uld
n
owb
ep
la
c
edi
nn
ew
Ne
ut
r
al I1
Current
: 430A
I2 : 430A
P
ol
e. I3 : 430A
Available in configuration of-

• NRYB to RYBN
• NRYB to NBYR
• NRYB to BYRN CT Wire Harness
Neutral Configurator
MTX-1.0/1G/1Gi/1.5G/1.5Gi
3.5/3.5EC/3.5H/4.5
6
)
Ex
te
r
n
al
Neu
t
r
al
Cs 3 Pole ACB
T
Y
Load
B
N NCT
In case of TPN system, NCT must be used to avoid nuisance tripping of the three pole ACB under unbalanced load
condition.
In case of current unbalance,
IR + IY + IB + IN = 0, but
IR + IY + IB ≠ 0
In absence of NCT, the EF enabled Protection & Control Unit will follow the second equation resulting in false indication of
EF, and will trip if it exceeds threshold value, causing undesirable interruptions in the Electrical system and deterioration of
ACB life.
Accessories 82
For Earth fault protection and protection of Neutral against overloads, Neutral CT is required. For 4-Pole breakers, the
CT is provided inside the breaker, to be used on 4 wire system whereas for 3-pole breakers, external CT is available
separately.
It is important that with OMEGA System of breaker, special neutral CTs supplied by L&T are used.
65
40 13
4
NS
19
Fra m eS eR
i
z ating
42
3
S
N
1, 2 & 3 400/630/800/
1, 2 & 3 1000/1250/1600
72
Ns3 Ns4
(ref. Page 14 for Frame size details)
42
TERMINAL THICKNESS 15 mm.
19
90
NS
12.5 40 13
3
19
NS
45.5
4
F
r
a
me eR
S
i
z ati
ng
1 2000/2500
72
Ns3 Ns4
45.5
19
65
22.15 27 27 13
4
NS
19
F
r
a
meeR
S
i
z a
t
i
ng
45.5
3
NS
2000/2500/
2&3
3200/4000
72
Ns3 Ns4

45.5

19
98.3
65
12.5 40 40 40 13
4
NS
19
45.5
F
r
a
me eR
S
i
z ati
ng
3
NS
3 5000/6300
72
Ns3 Ns4
45.5
19
145
M12 / Equivalent bolts to be used for links termination.

Tightening torque: 3.2 kgfm
All Dimensions in mm
Control Circuit Wiring
UW-MTX1.0/1G/1Gi/1.5G/1.5Gi/3.5/3.5EC/3.5H/4.5
For URM / SRM

only one
can be used
Closing X=111/121
Release X1= 112/122
# X2 = 114/124
5 6m
*
SIC Terminations
Electrical Aux. Aux. Aux. Aux. Under Common Ready Protection &
ZSI
Charging Contact Contact Contact Contact Voltage Fault to Remote Control
Terminals
Device # “NC” “NC” “NC” “NC” Release # Indication Close Reset Unit
2 3 3 3 3 4 1m 1m 1
Aux. Aux. Aux. Aux. Shunt Electrical

Charging Contact Contact Contact Contact Rel. # Position
Indication “NO” “NO” “NO” “NO” & “NO” Indication
2m 3 3 3 3 6 8e
}}
}
}
}
}
}
}
}
}
}
}
}
}
}
}
}
}
}
}
X
D-
11
21
31
41
X1
D1
A1
C1
N1
12
22
32
42
13
23
33
43
D+
X2
14
24
34
44
V1
V2
V3
D2
A2
C2
N2
SI2
SI1
CN
Z-L
C-H
C-L
RR-
AL-
Z-H
GI1
GI2
DCN
131
101
AS-
AS-
V0
CH1
TST
EC1
SO1
M-G
CH2
132
102
C-G
CMN
TCS
EC2
134
104
SO2
RR+
AL+
GO2
AS+
AS+
GO1
Legend
Control
circuit
equipment
Ref. No.
The above diagram gives a generic configuration for control termination on the breaker. For specific details, refer Connection diagram
(pages 79 to 84) specific to the P&C unit installed in the breaker.
# For using electrical accessories with DC Control Supply, it is recommended to connect D1/A1/C1 to +ve and D2/A2/C2 to -ve.
# m indicates micro switch
* These ZSI Terminals should only be used for MTX 1Gi/1.5Gi Releases.
84
Connection Details 85
N R Y B
TST
134
104
114
124
RR+
TCS
CN
DCN
13
23
33
43
132
102
112
122
D1
EC1
CH1
11
21
31
41
A1
C1
UW-MTX1.0
.1 .2
.3
.3
.3
.3
.1
.1
.1
.1
RR
UR
SR
CR
EC
AX
AX
AX
AX
CFM
PI
UW-MTX 1.0
.4
.4
.4
.4
.2
.2
.2
.2
LOAD
D2
14
24
34
44
RR-
CMN
EC2
CH2
12
22
32
42
A2
C2
131
101
111
121
U/V Fault Signal

Electric Spring Common Ready
Auxiliary Contacts U/V Closing Shunt /Shunt Trip Signal Electrical Remote
Main Circuit Protection & Control Unit Charging Charge Fault to
4ON + 4NC Release Release Release (only one can Position Reset
Device Indication Indication Close Indication
be used)
Ref. No. 1 2 2m 3 4 5 6 1m 7 4m/6m 8e

Connection Details
N R Y B
TST
134
104
114
124
RR+
TCS
CN
DCN
13
23
33
43
132
102
112
122
EC1
CH1
11
21
31
41
D1
A1
C1
UW-MTX 1G/1.5G
.1 .2
.3
.3
.3
.3
.1
.1
.1
.1
RR
UR
SR
CR
EC
AX
AX
AX
AX
PI
CFM
UW-MTX 1G/1.5G
.4
.4
.4
.4
.2
.2
.2
.2
N2
N1
LOAD
14
24
34
44
RR-
CMN
EC2
CH2
12
22
32
42
D2
A2
C2
131
101
111
121
U/V Fault Signal

Electric Spring Ready /Shunt Trip Signal Electrical Remote
Main Circuit Protection & Control Unit Charging Charge
Auxiliary Contacts U/V Closing Shunt Common Fault to
4NO + 4NC Release Release Release Indication (only one can Position Reset
Device Indication Close be used) Indication
Ref. No. 1 2 2m 3 4 5 6 1m 7 4m/6m 8e
N1, N2: External Neutral CT

86
Connection Details 87
N R Y B
114
112
134
104
124
13
23
33
43
132
102
122
11
CN
21
31
41
A1
DCN
D1
C1
CH1
RR+
TCS
TST
EC1
SI1
GI1
AS+
SO1
GO1
ACB STATUS
.1 .2
.3
.3
.3
.3
.1
.1
.1
.1
SR
RR
UR
CR
EC
PI
CFM
UW-MTX 1.0Gi/1.5Gi
UW-MTX 1Gi/1.5Gi
.4
.4
.4
.4
AX .2
AX .2
AX .2
AX .2
N1
N2
LOAD
SI2
GI2
AS-
14
24
34
44
111
12
22
32
42
CMN
D2
C2
A2
CH2
SO2
131
101
121
EC2
GO2
RR-
ACB STATUS
U/V Fault Signal
Electric Spring Common Ready
Auxiliary Contacts U/V Closing Shunt /Shunt Trip Signal Electrical Remote
Main Circuit Protection & Control Unit Charging Charge Fault to Position
4NO + 4 NC Release Release Release Indication (only one can Reset
Device Indication Close Indication
be used)
Ref. No 2 2m 3 4 5 6 1m 7 4m/6m 8e
AS+ : Auxiliary 24V DC

AS- : Ground
SOUT : ZSI S/C Output
SIN : ZSI S/C Input
GOUT : ZSI E/F Output
GIN : ZSI E/F Input
N1 : External Neutral CT
N2 : External Neutral CT
Connection Details
N R Y B
TST
134
104
114
124
D+
AL+
AS+
RR+
TCS
CN
DCN
V3
13
23
33
43
132
102
112
122
M-G
C-H
Z-H
V1
EC1
CH1
11
21
31
41
D1
A1
C1
ACB STATUS
.1 .2
.3
.3
.3
.3
.1
.1
.1
.1
SR
RR
UR
CR
EC
UW-MTX 3.5/
PI
CFM
.4
.4
.4
.4
AX .2
AX .2
AX .2
AX .2
3.5EC/3.5H/4.5
UW-MTX 3.5/3.5EC/4.5
N1
N2
LOAD
C-L
Z-L
14
24
34
44
D-
AL-
AS-
RR-
V0
CMN
V2
EC2
CH2
12
22
32
42
D2
A2
C2
C-G
131
101
111
121
ACB STATUS
Electric Spring Ready U/V Fault Signal Electrical
/Shunt Trip Signal
Auxiliary Contacts U/V Closing Shunt Common Remote
Main Circuit Protection & Control Unit Charging Charge Fault to Position
4NO + 4 NC Release Release Release Indication (only one can Reset
Device Indication Close be used) Indication
Ref. No. 1 2 2m 3 4 5 6 1m 7 4m/6m 8e
AS+, AS- : 24V DC Power Supply C-L : CAN-Low D+ : MOD A

AL+, AL- : OL ALARM+, OL ALARM- C-H : CAN-High D- : MOD B
This output can be connected
to 5V-30V dc 150mA relay or M-G : MOD-GND N1 : External Neutral CT
any indicating device for C-G : CAN-GND N2 : External Neutral CT
indication or Load V0,V1,V2,V3 : N ,R,Y,B, VOLTAGE I/P. Z-L : ZSI CAN-Low
shedding purpose.
Z-H : ZSI CAN-High
88
89
Z-L AS-
AS+
Z-H
GIN
PWR
COMM SIN
T
MNT
S-OUT G-OUT S-IN G-IN

SOUT
ZSI
GOUT
T1-T4
} connection to breaker terminals
CAN-H
}
CAN-L AS+
AS-
? CAN L
AS+ CAN H
AS-
4 DIGITAL (24V DC/230V AC) Inputs

IP3 IP4 COM CT input CT input Coil Supply
IP1 IP2
1
T4 T3 T2 T1
IP1 IP2 IP3 IP4 COM
STATUS RELAY PWR
COMM
T MNT
RJ 45 CABLE
TCS
AO1 AO2 AO3 AO4

OP1 OP2 OP3 OP4 + - + - + - + - OP1 OP2 OP3 OP4
Matrix Connection Diagram

OP1 OP2 OP3 OP4 AO1 AO2 AO3 AO4 OP1 OP2 OP3 OP4 CAN Bus
4 DIGITAL O/PS 4 ANALOG O/PS 4 RELAY O/PS EL RELAY O/P REF RELAY O/P TCS RELAY O/P
AS+ : Auxiliary 24V DC Z-L : ZSI CAN-Low

AS- : Ground Z-H : ZSI CAN-High
SOUT : S/C Output CAN- H : CAN-High
SIN : S/C Input CAN- L : CAN-Low
GOUT : E/F Output
GIN : E/F Input
T1-T4 : Thermistor Inputs
Note: One Power Supply module can be connected to maximum 5 modules

90
Mounting & Termination
Mounting 92
Termination on Draw-out Breakers

OMEGA System of ACB terminals offer more contact
area to accept Aluminium Links.
OMEGA System of ACBs Universal Flat terminals

greatly facilitate termination. These terminals directly
support all commonly used types of termination as
shown in adjoining figure.
OMEGA System of ACB’s are having inbuilt nutplates

(M12 Threading) in Cradle terminal, to facilitate
termination.
Terminal Adaptor
If required Terminal Adaptors are available as an accessory
Vertical/Horiz. Adaptors Vertical/Horiz. Adaptor Vertical/Horiz. Adaptor

for Frame 1 for Frame 2 for Frame 3
Installation of Terminal Adapter Installation of Terminal Adapter

for frame1 for frame 2
Terminal Adaptors supplied with Breakers

Upto 1600A - Bottom only
Rest Breakers - Top & Bottom both
93 Mounting
Termination Methods
For Fixed Breakers
CAUTION: X = 100 -150 mm

Inadequate termination support may result in X
overheating & adversely affect performance
during short circuit conditions.
For Draw-out Breakers

With Terminal Adaptor
With Universal Terminals
15 max
40
X
X
X = 100 -150 mm
* Maintain adequate clearance between links as applicable standards

Mounting 94
400-1600A N & 400-2500A S/H Fr.1 3P

Fixed Circuit Breaker
300 min
300 min
7
Frame1 A
400-2000 N/S 326
2500 S 324 OFF ON
430
400-2500 H 324
A A
Panel
Door
142
6 335 6 A
347 25 112 25
A
Draw-out Circuit Breaker

45 mm*
45mm*
7
Panel
Door
433
OFF ON
16
Disconnected
35
Test
25.5 A
A
49.5 250 47.5 250
347 62.4 280
421
(250) (47.5)
(62.4)
Use this
mounting hole Use this
mounting hole
(250)
(280)
These 2 supports
are must
Use any one of

these two
mounting holes
Use any one of
these two
mounting holes
A Mounting holes suitable for M10 / Equivalent BS bolt
95 Mounting
400-1600A N & 400-2500A S/H Fr.1 4P (100% N)

300 min
300 min
Frame1 A
400-2000 N/S 326
2500 S 324 OFF ON
430
400-2500 H 324
A A
6 435 6 Panel
447 A Door
25 112 25
A

45 mm*
45 mm*
7
Panel
Door
433
OFF ON
16
Disconnected
35
Test
A A 25.5 A
49.5 100 250 47.5 250
447 62.4 280
421
Optional 100 (250) (47.5)

support
(62.4)
Use this
mounting hole
(250)
These 2 supports
(280)
are must
Use any one of

these two
mounting holes
Use any one of Use any one of

these two these two
mounting holes mounting holes
Details of 4P (200%) on request

Mounting 96
400-3200A N & 400-4000A S/H Fr.2 3P

300 min
300 min
Frame2 A
400-2500 N/S 326
OFF ON
430
3200 N/S 324

400-3200 H 324
4000 S/H 324

A A
6 435 6 Panel
447 A Door
25 112 25
A

45 mm*
45 mm*
7
Panel
Door
433
16
Disconnected
35
Test
A 25.5 A
A
49.5 100 250 47.5 250
62.4 280
447 421
Optional 100 (250) (47.5)

support
(62.4)
Use this
mounting hole
(250)
These 2 supports
(280)
are must
Use any one of

these two
mounting holes
Use any one of Use any one of

these two these two
mounting holes mounting holes
97 Mounting
400-3200A N & 400-4000A S/H Fr.2 4P (100% N)

300 min
300 min
Frame2 A
400-2500 N/S 326
430
3200 N/S 324

400-3200 H 324
4000 S/H 324
A A Panel Door
(Outer surface)
A 142
6 569 6
25 112 25
581
A

45 mm*
45 mm*
7
Panel
Door
433
16
Disconnected
35
A Test
49.5 100 250 A 47.5 25.5
A
581 250
62.4 280
421
(49.5) (100) (250) (47.5)
(62.4)
Optional Use this

support mounting hole
Use this
mounting hole
(250)
(280)
These 3 supports
are must
Use any one of

these two
mounting holes
Use any one of
these two Use any one of
mounting holes these two
mounting holes
Details of 4P (200% N) on request

Mounting 98
400-6300A H/V Fr.3 3P

300 min
300 min
7
430
OFF ON
A A
Panel Door
(Outer surface)
6 635 6 A 142
647 25 112 25
334

45 mm*
45 mm*
7
Panel
Door
433
OFF ON
16
Disconnected
35
35.5 Test
A
49.5 A 100 250 A 47.5 250
647 62.4 280
431
(100) (250) (47.5)

Optional
(49.5)
Use this
support
(62.4)
mounting holes
Use this
mounting hole
(250)
(280)
These 3 supports
are must
Use any one of

these two
mounting holes
Use any one of
Use any one of these these two
two mounting holes mounting holes
99 Mounting
400-6300A H/V Fr.3 4P (100% N)

300 min
300 min
7
430
A A
Panel Door
(Outer surface)
6 835 6 A 142
847 25 112 25
334
45 mm*
45 mm*
7
Panel
Door
433
16
Disconnected
35
35.5 Test
A A A A
49.5 200 100 250 47.5
250
847 62.4 280
431
(49.5) (200) (100) (250) (47.5)

Optional
support
(62.4)
Use this
mounting hole
Use this
mounting holes
(250)
(280)
These 4 supports
are must
Use any one of

these two
mounting holes
Use any one of these Use any one of these

two mounting holes Use any one of
Four mounting holes these two
mounting holes
Details of 4P (50% N) on request

Termination - Fixed Breakers 100
Flat Termination
C
400-1600N/S, 2000A N/S & 400-2000A H Fr.1-3P 32
11
A
B
M10
105
A
B
32
122
C
41
Bolt length 100 100

347
15
M10 bolts to be used for link termination
Bolt length for mounting Holes (on both sides) for Earthing Tightening torque: 3.0 kgfm
link(s) on Flat Terminals connections by M10/Equivalent BS bolt
to be cumulative link(s) Frame1 A B C
thickness + 15 mm. 400-1600 N 24 50 50
400-1600 S 24 50 65
2000 N/S 24 50 65
400-2000 H 30 55 65
Horizontal Termination
74
400-2000 N/S/H Fr.1 3P 63
15
69
40
69
108.8
19
Ø12.9 27
100 100
Breaker Adaptor
M12 / Equivalent BS bolts to be Rating Cat. No.
used for link termination 400-2000 N/S CL60967OOOO
400-2000 H CL60968OOOO
101 Termination - Fixed Breakers
Vertical Terminals
74
400-2000A N/S/H 19
65
27 40
65
Ø12.9
117.5
100 100
63
15
100 100
Breaker Adaptor
M12 / Equivalent BS bolts to be used for link termination Rating Cat. No.
Tightening torque: 3.2 kgfm 400-2000 N/S CL60967OOOO
400-2000 H CL60968OOOO
Vertical Terminals 72
63
2500A S/H Fr.1-3P (Adaptor-CL60976OOOO) 19
27 27
100
45
100
Ø12.9
80.8
100 100
20
100 100
M12 /Equivalent BS bolts to be used for link termination

Flat Termination
400-1600 N/S, 2000A N/S & 400-2000A H Fr.1-4P C
32
11
B
M10
105
B
122
41
C
15 100 100 100 73.5
Holes (on both sides) for Earthing
connections by M10/Equivalent BS bolt. 447
M10 bolts to be used for link termination Bolt length Bolt length for Frame1 A B C
Tightening torque: 3.0 kgfm mounting link(s) on 400-1600 N 24 50 50
Flat Terminals 400-1600 S 24 50 65
to be cumulative 2000 N/S 24 50 65
link(s) thickness +
15 mm. 400-2000 H 30 55 65
Horizontal Termination 74
400a-2000A N/S/H Fr.1-4P 63
15
69
40
69
108.8
19
27
Ø12.9 100 100 100
Breaker Adaptor
Tightening torque: 3.2 kgfm 400-2000 N/S CL60967OOOO
400-2000 H CL60968OOOO
Vertical Terminals
400-2000A N/S/H Fr.1-4P 74
19
65
27 40
65
Ø12.9
117.5
100 100 100
15
100 100 100
Breaker Adaptor
400-2000 N/S CL60967OOOO
400-2000 H CL60968OOOO
Vertical Terminals 72
63
2500A S/H Fr.1-4P 19
45 23 27 27
100
100
Ø12.9
80.8
100 100 100
20 100
100 100
M12 / Equivalent BS bolts to be used for link termination

Flat Termination
400-1600A N/S/H Fr.2 3P
D
32
B
M10
A
105
C
A
122
Bolt length
133.3 133.3 90
41
447
Bolt length for 15
mounting link(s) on M10 / Equivalent BS bolts to be used for link termination.
Flat Terminals Tightening torque: 3.2 kgfm
to be cumulative Holes (on both sides)
Frame1 A B C D
link(s) thickness + for Earthing connections
15 mm. by M10/Equivalent BS bolt 400-1600 N/S 50 11 24 81.2
400-1600 H 55 9 30 98.4
400-3200 N/S/H Fr.2 3P
72
74.2
63
20
179
103.8
19
27
54 DIA.12.9
133.3 133.3
M12 / Equivalent BS bolts to be used for link termination.

Details of 4P(200% N) on request.
Vertical Terminals
400-3200A N/S/H & 4000A S/H Fr.2-3P
72
46.7
19 63
100
54
27
53.5
DIA.12.9
77.2
133.3 133.3
M12 / Equivalent BS bolts to be used for links termination.

133.3 133.3 20
Top Horizontal & Bottom Vertical Termination

72
4000A S/H Fr.2-3P 63
20
53
19
27 27
100
77.2
100
27 27 Ø12.9
19
63
133.3 133.3
Flat Terminals
400-1600A N/S/H Fr.2-4P
D
32
B
M10
C
A
105
C
A
122
Bolt length
41
133.3 133.3 133.3

15 581
Bolt length for

mounting link(s) on M10 / Equivalent BS bolts to be used for links termination.
Flat Terminals Tightening torque: 3.2 kgfm
link(s) thickness for Earthing connections
+ 15 mm. by M10/Equivalent BS bolt Frame1 A B C D
400-1600 N 50 11 24 81.2
400-1600 S 55 9 30 98.4
400-3200A N/S/H Fr.2-4P
72
63
20
73
45
73
103.8
27 27 20
19
Ø12.9 100
M12 / Equivalent BS bolts to be used for links termination. 133.3 133.3 133.3
Details of 4P (200% N) on request.

All Dimensions in mm All Dimensions in mm
Vertical Termination 63
400-3200A N/S/H & 4000A S/H Fr.2-4P (100% N) Ø12.9 19
27
100
54
23
53
100
77.2
133.3 133.3 133.3
20
Tightening torque: 3.2 kgfm 133.3 133.3 133.3
Top Horizontal & Bottom Vertical Termination

72
4000A S/H Fr.2-4P 63
20
53
19
27
100
27
77.2
100
27 27 Ø12.9
19
63
133.3 133.3 133.3
400-4000A H/V Fr.3 3P

Flat Termination 400-1600A
165
65
32
9 M10
56
10
30
56
105
30
Bolt length
41
122
15
100 100 100 100 100 73.5
Bolt length for
mounting link(s) on 647
Flat Terminals
link(s) thickness for Earthing connections M10 / Equivalent BS bolts to be used for link termination.
+ 15 mm. by M10/Equivalent BS bolt Tightening torque: 3.2 kgfm
400-4000A H/V Fr.3 3P

82
84.2
63
19
A
75
30
112.8
M12 / Equivalent BS bolts to Breaker 19

be used for links termination. Rating Dim. A
Tightening torque: 3.2 kgfm 27
400-4000A 15 Ø12.9 100 100 100 100 100
5000A 20
400-5000A H/V Fr.3 3P

Vertical Termination
82
89.2
63
19
27
19
40
75
Ø12.9
117.8
100 100 100 100 100
Breaker
Rating Dim. A
M12 / Equivalent BS bolts to be
400-4000A 15
used for links termination A
Tightening torque: 3.2 kgfm 5000A 20 100 100 100 100 100
6300A H/V Fr.3 3P

82
51.2
A 19 63
27
100
27
23
45
Ø12.9
80.8
100 100 100 100 100
20
100 100 100 100 100

400-5000A H/V Fr.3 4P (100% N)

Flat Termination 400-1600A
65
32
9 M 10
56
10 30
105
56
30
122
41
Bolt length
15 100 100 100 100 100 100 100 73.5
847
Bolt length for

mounting link(s) on
Flat Terminals
link(s) thickness for Earthing connections M10 / Equivalent BS bolts to be used for links termination.
+ 15 mm. by M10/Equivalent BS bolt Tightening torque: 3.2kgfm
400-4000A H/V Fr.3 4P (100% N)

82
63
19
15
69
30
69
108.8
ø12.9
19
65
100 100 100 100 100 100 100
27
Details of 4P(50% N) on request.

400-5000A H/V Fr.3 4P (100% N)

82
89.2
63
19
27
19
40
65
Ø12.9
117.8
100 100 100 100 100 100 100
M12 / Equivalent BS bolts to be Breaker

used for links termination. Rating Dim. A
A
Tightening torque: 3.2 kgfm 100 100 100 100 100 100 100
400-4000A 15
5000A 20
6300A H/V Fr.3 4P (100% N)

82
19 Ø12.9
23 27 27
100
45
80.8
100 100 100 100 100 100 100
20
100 100 100 100 100 100 100
Termination - Draw-out Breakers 112
400A-1600A N/S/H, Fr.1 3P 65
Flat Terminals
See Detail A
DETAIL A
56.8
14.5
10.4
105
36
Ø12.5
36
150
25.5
Bolt length
100 100 73.5

15
16
347
Bolt length for mounting link(s) on

Flat Terminals to be cumulative link(s) M12/ Equivalent BS bolts to be used for links termination.
Thickness + 20 min to 25 max Tightening torque: 3.2 kgfm
Horizontal Terminals
400A-2000A N/S/H 36 65
M12
22.5
36
15
105
Ø12.9
150
45
100 100
15
73.5
347
88.5 16
M12/ Equivalent BS bolts to be used for links termination.
Vertical Terminals 36 65
400A-2000A N/S/H 15
M12
22.5
36
27
65
105
Ø12.9
150
45
100 100
15
73.5
347
88.5 16
M12 / Equivalent BS bolts to be used

All Dimensions in mm for links termination Tightening torque: 3.2 kgfm
113 Termination - Draw-out Breakers
2500A S & 400-2500A H Fr.1-3P 65 20 36

Vertical Terminals
95.5
70
20
Ø12.9
27 27
98
36
Ø12.9
105
150
15
100 100
16
73.5
347
M12 / Equivalent BS bolts to be used for links termination
400A-2000A, N/S/H Fr.1-4P (100%N)

Flat Terminals 65
400A- 1600A, N/S/H
See Detail A
65
14.5 36
Ø12.5
56.8
105
56.8
36
10.4
Detail A
150
25.5 100 100 100 73.5
Bolt length 447
15
16
Bolt length for mounting link(s) on Flat

Terminals to be cumulative link(s) M12/ Equivalent BS bolts to be used for links termination.
thickness +20 min to 25 max. Tightening torque: 3.2 kgfm
400A - 2000A N/S/H
36 65
Ø12.9 M12
15
36
105
22.5
150
45
100 100 100

88.5
73.5
447
15
16
Vertical Terminals
400A - 2000A N/S/H
36 15 65
M12
22.5
65
27
36
105
Ø12.9
150
45
88.5 100 100 100
73.5
447
15
16

Vertical Terminals
2500A S & 400-2500A H, Fr.1-4P (100%N)
20 65 36
95.5
70
Ø12.9
20
27 27
36
98
105
Ø12.9
150
100 100 100
73.5
447
15
16

400A-3200A, N/S/H Fr.2-3P

65
Flat Terminals 36
400A-1600A, N/S/H
M12
77.2
36
105
77.2
36
140
25.5
Bolt length
15
16 133.3 133.3 90
447
Bolt length for mounting link(s) on M12/ Equivalent BS bolts to be used for links termination.
Flat Terminals to be cumulative link(s) Tightening torque: 3.2 kgfm
thickness+20 min to 25 max
98
400A-3200A, N/S/H
95.5
M12
20
20
65
105
45
Ø12.9
140
133.3 133.3 90
15 16 447
Vertical Terminals
36 20 20
400A-3200A, N/S/H
95.5
20 M12
Ø12.9
27 27
98
36
105
36
98
140
45
70 36
133.3 133.3 90
15 16 447

4000A S/H Fr.2-3P

Vertical Terminals
20 65
95.5
12.9
45
2127 27 27 27
165
150
36 36
105
20
58
36
2127 27 27 27
178.5
150
140
15
70
16 90 133.3 133.3
25.5
447
4000A S/H Fr.2-3P

Top Horizontal & Bottom Vertical Terminals
100
36
95.5
3 HOLES 12.9
100
72
32
20
83.8
45
36
21 27 27 27 27
179
150
90 133.3 133.3
Ø12.9 447
Horizontal: CL60316OOOO
Ø12.9
20
Tightening torque: 3.2 kgfm 23 27 27
400A-3200A,N/S/H,Fr.2-4P (100% N)
Flat Terminals
400A-1600A,N/S/H 65
36
M12
77.2
36
105
77.2
36
25.5
140
15
Boltlength 16
90 133.3 133.3 133.3

581
Bolt length for mounting link(s) on

Flat Terminals to be cumulative link(s)
400A-3200A N/S/H 98 36
N M12
95.5
20
36
65
20
105
45
Ø12.9
140
15
133.3 133.3 133.3 90

16
581
Vertical Terminals
400A-3200A N/S/H 20 36 65
95.5 M12
Ø12.9 20
2727
98
36
105
98
140
45
70
16 133.3 133.3 133.3 90.5

15
581

Tightening torque: 3.2kgfm
4000A S/H Fr.2-4P

Vertical Terminals
20 65
Ø12.9 95.5
45
2127 27 27 27
165
150
36 36
105
20
58
36
2127 27 27 27
178.5
140
150
90 133.3 133.3 133.3

15
70
16 581
25.5
4000A S/H Fr.2-4P

100
Top Horizontal & Bottom Vertical Terminals 36
95.5
3 Holes Ø12.9
100
72
32
20
83.8
45
36
178.5
21 27 27 27 27
150
90 133.3 133.3 133.3
Ø12.9 581
Horizontal: CL60316OOOO
Ø12.9
20

Tightening torque: 3.2 kgfm 23 27 27
1
1
9 T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s
4
0
0-
4
000
A
H/
VF
r
.3
3P 165
36
F
l
at
Te
r
mi
na
ls 10
400-1600A
36
56
105
B
o
l
tl
en
gt
h Ø 12.9
56
36
179
35.5
Bolt length for
mounting link(s) on 100 100 100 100 100 73.5
15
Hole (on Both Sides) for Earthing
Flat Terminals 16 Connections By M10 / Equivalent Bs Bolt 647
to be cumulative
link(s) thickness
+20 min to 25 max
165
H
o
r
i
zo
nt
a
lT
er
mi
na
ls 36 Ø12.9
400-4000A H/V
36
40 65
22.5
15
179
45
70
35.5
15
16 73.5 100 100 100 100 100

647
165
8
22.5
70
M12 / Equivalent BS bolts to be used for links termination. Tightening torque: 3.2 kgfm
15 27 Ø12.9
V
e
r
t
ic
a
lT
e
rm
i
na
ls
400-4000A H/V 165
36 Ø12.9 15
Ø12.9
22
125
134
27
36
58
22
36
125
27
183
22.5 16
15
70 35.5 73.5 100 100 100 100 100

647
M12/Equivalent BS bolts to be used for links termination Tightening torque: 3.2 kgfm
T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s 1
2
0
5
0
00
-
6
300
A
H/
VF
r
.3
3P
Horizontal Terminals 5000A
165
36 Ø12.9
36
40 65
22.5
20
45
70 179
35.5
15
16 73.5 100 100 100 100 100

647
165
15
22.5
70
15 27 Ø12.9
* H-H termination recommended for bus coupler only Tightening torque: 3.2 kgfm
V
e
r
t
ic
a
lT
e
rm
i
na
ls
5
00
0A

165
36 Ø12.9 20
Ø12.9
22
125
134
27
36
58
22
36
125
27
183
20 16
15
73.5 100 100 100 100 100

70 35.5 647
1
2
1 T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s
V
e
r
t
ic
a
lT
e
rm
i
na
ls
6300A
165
Ø12.9 20
36
Ø12.9
21
27
150
165
36 36
58
21
36
183
27
150
150
20 73.5 100 100 100 100 100

16
15
70 35.5 647

T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s 1
2
2
4
0
0A
-
5
000
A
H/
VF
r
.3
-
4P
(5
0
%N
)
F
l
at
Te
r
min
a
ls 165
36
4
0
0A-
1
600
AH
/
V
10
56
36
Bolt length
105
ø12.9
56
36
179
Bolt length for mounting link(s) on 35.5
Flat Terminals to be cumulative link(s)
15
Hole (on both sides) 100 100 100 100 100 73.5
16 for Earthing connections 100
by M10 / Equivalent BS bolt
747
165
H
o
r
iz
o
nt
al
Te
rm
i
na
ls 36 Ø12.9
4
0
0A
-
4
000
A H
/
V 10*
45
Ø12.9
36
40 65
22.5
15
165
70
179
22.5
35.5
8
70
16
15
15 27 Ø12.9 73.5 100 100 100 100 100 100

M12/ Equivalent BS bolts to be used for links termination. 747
165
V
e
r
ti
c
alT
e
rm
i
na
ls 36 Ø12.9
15
4
0
0A
-
400
0A
HVØ12.9 10*
/
22
125
36
134
27
58
22
36
134
183
125
27
22.5 73.5 100 100 100 100 100 100

70
15
747
35.5 16
165
V
e
r
ti
c
alT
e
rm
i
na
ls 20
36 Ø12.9
5
0
00
AH/
V Ø12.9
10*
22
125
36
134
27
58
22
125
27
36
183
20
M12/Equivalent BS bolts to
15
70
be used for link termination 73.5 100 100 100 100 100 100
35.5 16
747
All Dimensions in mm *10 mm Terminal height difference

due to equalizer for Neutral.
1
2
3 T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s
4
0
0-
4
000
A
H/
VF
r
.3
4P
(
10
0%
N
)
165
F
l
at
Te
r
mi
na
ls 36
4
0
0-
16
00
A
10
36
56
Bolt length
105
ø12.9
56
36
179
35.5
Bolt length for mounting
link(s) on Flat Terminals
to be cumulative link(s)
100 100 100 100 100 100 100 73.5
15
thickness +20 min to 25 max 16

Hole(on both sides)
for Earthing connections
by M10 / Equivalent BS bolt 847
Ø12.9
H
o
ri
z
ont
a
lT
er
mi
na
ls 165
8
4
0
0-
40
00
A
70
22.5
15 27
165
36 Ø12.9
36
40 65
22.5
45
15
179
63
35.5
16 73.5 100 100 100 100 100 100 100

15
847
V
e
r
ti
ca
lT
e
rm
i
na
ls
4
0
0-
4
000
A
165
36 15
Ø12.9
Ø12.9
22
125
134
36
27
58
22
183
36
125
27
22.5
70 73.5 100 100 100 100 100 100 100
15
35.5 16 847
M12/Equivalent BS bolts to be used for links termination Tightening torque: 3.2 kgfm All Dimensions in mm
T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s 1
2
4
4
0
0-
6
300
A
H/
VF
r
.3
4P
(
10
0%
N
)
H
o
r
i
zo
nt
a
lT
er
mi
na
ls
5
00
0A
165
36 Ø12.9
36
40 65
22.5
20
45
179
70
35.5
15
16 73.5 100 100 100 100 100 100 100

847
22.5
15
70

15 27
Ø12.9
V
e
r
t
ic
a
lT
e
rm
i
na
ls
5
00
0A

165
36
Ø12.9 20
Ø12.9
22
125
134
27
36
58
22
125
27
36
183
20
70
15
16 73.5 100 100 100 100 100 100 100

35.5
847
1
2
5 T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s
V
e
r
t
ic
a
lT
e
rm
i
na
ls
6
30
0A
165
36 20
Ø12.9
Ø12.9
21
150
150
27
36 36
58
58
21
36
150
183
150
27
20
15
73.5 100 100 100 100 100 100 100

70 16
847
35.5

4
0
0A-
2
000
AH
/
V,
F
r.
3-
4P
(2
0
0%
N)
*
F
l
at
Te
r
min
a
ls
4
0
0A
-
1
600
AH
/
V
165
36
10*
56
36
105
ø12.9
36
56
179
25.5
N
15
Hole (on both sides)

100 100 100 100 100 73.5
16
for Earthing connections 647
by M10 / Equivalent BS bolt
Bolt length
Bolt length for mounting link(s) on *10 mm Terminal height difference
Flat Terminals to be cumulative link(s) due to equalizer for Neutral.
M 12/ Equivalent BS bolts to be used for links termination.
*Option for 400-1250A Fr.1-4P 200%N and 400-1600A Fr.2-4P 200%N Also available. All Dimensions in mm
T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s 1
2
6
H
o
r
i
zo
nt
a
lT
er
mi
na
ls
4
0
0A
-
2
000
AH
/
V 165
36 M12
10* 65
Holes - Ø12.9
Pitch 27 mm.
36
40 65
45
22.5
15
63
183
35.5
N
15
16 73.5 100 100 100 100 100

647
M12 / Equivalent BS bolts to be used for links termination. *10 mm Terminal height difference
Tightening torque: 3.2 kgfm due to equalizer for Neutral.
V
e
r
t
ic
a
lT
e
rm
i
na
ls
4
0
0A
-
2
000
AH
/
V
165
36 M12 15
45
Ø12.9 10*
27
40 65
19
36
22.5
183
63
35.5
N
15
16 73.5 100 100 100 100 100

647
V
e
r
t
ic
a
lT
e
rm
i
na
ls 165 20
36
F
O
R2
50
0
AH
/
V,
F
r.
3-
4P
(
20
0%
N
) M12
10*
Ø12.9 45
134
36
27
125
40
20
36
58
183
27
N
35.5
73.5 100 100 100 100 100
70
647
15
16
127 T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s
D
i
r
ec
tA
l
umi
ni
umt
e
rm
in
a
ti
on
F
r
a
me-
1:
40
0-
20
00
A
N/
S
/H
Popular Aluminium Termination

Aluminium cross
Frame Rating
section as per Flat Horizontal (with Terminal adaptor) Vertical (with Terminal adaptor)
Size (A)
IS/IEC (in sq. mm)
6 mm 10 mm 12 mm 6 mm 10 mm 12 mm 6 mm 10 mm 12 mm
75 - 2 runs 75 - 2 runs
50 - 3 runs 75 - 1 runs 75 - 1 runs
800 800 - 75 - 1 runs - -
75 - 2 runs 50 - 3 runs 50 - 3 runs
1000 1000 - 50 - 2 runs - - 50 - 2 runs - - 50 - 2 runs -

1
1250 1512 - 75 - 2 runs - - 75 - 2 runs - - 75 - 2 runs -
1600 1600 - 60 - 3 runs 75 - 2 runs - 60 - 3 runs 75 - 2 runs - 60 - 3 runs 75 - 2 runs
2000 3000 - - 75 - 4 runs - - 75 - 4 runs -

100 - 3 runs
Note: Above table is based on extensive study of popular bus-bar sizes used to terminate Air Circuit Breakers. However other bus-
bar sizes (in terms of thickness & width) can also be used to achieve bus-bar cross section recommended by IS & IEC.
De-rating of switchgear depends upon various factors such as cross section area, orientation and material of bus bar, healthiness
of bus-bar joints, panel construction, and ventilation, etc.
F
r
a
me-
2:
40
0-
32
00
A
Na
nd
4
00
-
40
00
A
S/
H

Aluminium cross
Frame Rating
section as per Horizontal (with Terminal adaptor) Vertical (with Terminal adaptor)
Size (A)
IS/IEC (in sq. mm)
6 mm 10 mm 12 mm 6 mm 10 mm 12 mm
2500 4000 - 100 - 4 runs - - 100 - 4 runs -
2 3200 6000
(1)
- 100 - 5 runs - - 150 - 4 runs -
(2) (1) 100 - 6 runs

4000 7200 - - 100 - 6 runs - - 150 - 4 runs
(1) Not as per standard but generally followed.

(2) Fr-2 4000A recommended for Top Horizontal + Bottom
Vertical & Top Vertical configurations only.
Vertical + Bottom
T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s 128
F
r
a
me-
3:
400
-
63
00
A
H/
V

Aluminium cross
Frame Rating
section as per Horizontal (with Terminal adaptor) Vertical (with Terminal adaptor)
Size (A)
IS/IEC (in sq. mm)
6 mm 10 mm 12 mm 6 mm 10 mm 12 mm
4000 7200* 160 - 8 runs 150 - 5 runs 150 - 4 runs - 125 - 6 runs 125 - 5 runs
3
5000 8000* Copper termination recommended
6300 10000* Copper termination recommended
*Not as per standard but generally followed

D
i
r
ec
tC
o
pp
e
rt
e
rm
in
a
ti
on
F
r
a
me-
1:
40
0-
20
00
A
N/
S
/H
Popular Copper Termination

Copper cross
Frame Rating
section as per IEC Flat Horizontal (with Terminal adaptor) Vertical (with Terminal adaptor)
Size (A)
(in sq. mm)
6 mm 10 mm 12 mm 6 mm 10 mm 12 mm 6 mm 10 mm 12 mm
50 -1 run 50 -1 run
800 500 - 60 - 1 run - - - - -
60 - 1 run 60 - 1 run
1000 600 - 60 - 1 run - - 60 - 1 run - - 60 - 1 run -

1
1250 800 75 - 2 runs - - 75 - 2 runs - - 75 - 2 runs - -
1600 1000 60 - 3 runs - - 60 - 3 runs - - 60 - 3 runs - -
2000 1500 - - 75 - 2 runs - - 75 - 2 runs -
129 T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s
F
r
a
me-
2:
40
0-
32
00
AN
an
d
40
0
-4
0
00
A
S/
H

Copper cross
Frame Rating
section as per IEC Horizontal (with Terminal adaptor) Vertical (with Terminal adaptor)
Size (A)
(in sq. mm)
6 mm 10 mm 12 mm 6 mm 10 mm 12 mm
2500 2000 - 100 - 2 runs - - 100 - 2 runs -

2
3200 3200
(1)
- 80 - 4 runs - - 80 - 4 runs -
100 - 4 runs
4000
(2)
4000
(1)
- 100 - 4 runs - - 150 - 3 runs -
(1) Not as per standard but generally followed.

(2) Fr-2 4000A recommended for Top Horizontal + Bottom
Vertical & Top Vertical configurations only.
Vertical + Bottom
bar sizes (in terms of thickness & width) can also be used to achieve bus-bar cross section recommended by IS & IEC. De-rating of
switchgear depends upon various factors such as cross section area, orientation and material of bus bar, healthiness of bus-bar
joints, panel construction, and ventilation, etc.
F
r
a
me-
3:
40
0-
63
00
A
H/
V

Copper cross section
Frame Rating
as per IEC Horizontal (with Terminal adaptor) Vertical (with Terminal adaptor)
Size (A)
(in sq. mm)
6 mm 10 mm 12 mm 6 mm 10 mm 12 mm
4000 4000* 160 - 5 run 150 - 3 runs - - 125 - 4 runs -
#
3 5000 6000* 160 - 7 run 150 - 4 runs# - 150 - 4 runs 125 - 4 runs
6300 7200* Vertical termination recommended - - 150 - 4 runs
*Not as per standard but generally followed

# Recommended for Bus coupler application only
bar sizes (in terms of thickness & width) can also be used to achieve bus-bar cross section recommended by IS & IEC. De-rating of
switchgear depends upon various factors such as cross section area, orientation and material of bus bar, healthiness of bus-bar
joints, panel construction, and ventilation, etc.
T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s 130
T
e
mp
e
ra
t
u
re
De
r
a
ti
ng
of
OM
EG
A
AC
B
s
C
u
r
re
n
tc
a
rr
y
in
gc
a
pa
c
it
y
at
di
f
fe
re
n
tt
e
mpe
r
a
tu
r
es
Omega Air Circuit Breaker can operate at higher temperatures than the reference temperature of 400C as prescribed in IS & IEC
standards, under certain installation conditions. However in some cases current-carrying capacity needs to be reduced in order to
follow temperature rise limits and safe working conditions.
The table below shows the current carrying capacity of U-POWER Omega ACB’s where T = temperatures measured around the
rear connections of the AIR Circuit Breaker.
C
u
r
re
n
tc
a
rr
y
in
gc
a
pa
c
it
yw
it
hc
o
pp
er
as
bu
s
-b
a
rm
a
te
r
i
al
&Ve
r
t
i
ca
lc
o
nf
i
gu
ra
t
i
on
C
u
r
re
n
tc
a
rr
y
in
gc
ap
a
c
it
ya
td
i
f
fe
re
n
tt
e
mpe
r
a
tu
r
e(
T)
F
r
a
mes
i
z
e&c
u
rr
e
nt
ra
t
i
ngV
er
s
i
on
s
O O O O O
4
0C50C5 5C 60C7 0C
N 800 800 800 800 800
UW1-08 S 800 800 800 800 800
H 800 800 800 800 800
N 1000 1000 1000 1000 1000
UW1-10 S 1000 1000 1000 1000 1000
H 1000 1000 1000 1000 1000
N 1250 1250 1250 1250 1250
UW1-12 S 1250 1250 1250 1250 1250
H 1250 1250 1250 1250 1250
N 1600 1600 1530 1450 1360
UW1-16 S 1600 1600 1600 1550 1460
H 1600 1600 1600 1600 1600
N 2000 2000 2000 2000 2000
UW1-20 S 2000 2000 2000 2000 2000
H 2000 2000 2000 2000 2000
UW2-25 N/S/H 2500 2500 2500 2500 2500
UW2-32 N/S/H 3200 3200 3200 3200 3050
UW2-40 S/H 4000 4000 4000 3900 3600
UW3-40 H/V 4000 4000 4000 4000 3850
UW3-50 H/V 5000 5000 5000 5000 4770
UW3-63 H/V 6300 6130 5840 5540 5230
Please refer to Pages 127-129 to get the corresponding bus-bar cross section area required with different current rating of
Air Circuit Breaker.
N ot e: The values indicated in the above tables are for general guideline for product selection. These values have been
extrapolated from test data and theoretical calculations. They cannot replace practical industrial application or a temperature rise
test. However de-rating of switchgear depends on others factors such as cross section area, orientation and material of bus-bar,
healthiness of bus-bar joints, panel construction, and ventilation, etc.
131 T
e
r
mi
na
ti
on-
Dr
aw
-
ou
tB
r
e
ak
er
s
A
l
t
it
ud
e
de
r
a
ti
ng
of
OM
EG
A
AC
B
s
As altitude rise from sea level, the density of that air reduces dramatically. Reduced air density at altitudes greater
than 2000 meters affects the ability of a circuit breaker to transfer heat and interrupt faults compared with sea
level.The ability of fault interruption reduces with the increase of altitute because di-electric strength of air also
reduces with density.
Al
t
it
ud
ede ra
t
i
ng
Altitude H (m) <2000 3000 4000 5000
Rated service voltage (at 50/60 Hz) Ue (V) Ue 0.9Ue 0.8Ue 0.7Ue
Rated Uninterrupted Current at 40OC In (A) In 0.98In 0.96In 0.94In
Impulse withstand voltage Uimp (kV) 12 11 10 8
Rated insulation voltage Ui (V) 1000 900 780 700
W
a
t
t
-
lo
ss
Da
t
ao
fO
ME
G
AA
CB
s
W
a
t
t
lo
ss
v
al
ue
Watt loss plays an important role in the electrical performance of Air Circuit Breaker. Factors like overall dimension, rated current
carrying capacity of Bus-bar and watt loss of apparatus attached to the Air Circuit Breaker also plays an important role in
calculation of watt loss data.
Total watt loss value is measured at rated current (In) of 3 Pole Air Circuit Breaker at 50/60 Hz. (W=3xInˆ2xR), where
R is the resistance measured across the upper & lower terminated of ACB.
F
r
a
meS
i
z
e&Cu
r
r
en
t F
o
rd
r
aw
-
ou
tA
C
B(
Wat
t
)
R
at
i
ng N S H V
UW1-08 100 50 35
UW1-10 160 65 50
UW1-12 210 100 65
UW1-16 325 160 100
UW1-20 440 390 220
UW2-25 560 560 465
UW2-32 600 600 600
UW2-40 740 740
UW3-40 500 500
UW3-50 750 750
UW3-63 1000 1000
ACB Ordering Information 132
ACB ordering information:
UW 1 08 N X D 1 2 9 0 0(5) (7)
OMEGA 800A Fr-1 50kA 3P EDO UW-MTX1.5G
Special Applications
800V Operational Voltage M
1000V Operational Voltage H
(3)
Temperature Rise Protection
Not Required 0
Required 1
Selection for P&C Units

Frame Size B/C (w/o protection) 0
UW - MTX1.0 7
Frame - I 1
UW - MTX1G 8
Frame - II 2
UW - MTX1Gi B
Frame - III 3
UW - MTX1.5G 9
UW - MTX1.5Gi C
UW-MTX3.5 3
UW-MTX3.5EC(6) 4
Current Ratings
UW-MTX3.5H 6
400A 04
UW-MTX4.5 5
630A 06
800A 08 Type
1000A 10 Manually Operated 1
1250A 12 Electrically Operated 2
1600A 16 (2)
Selection for control voltage
2000A 20
For Manually Operated 0
2500A (4) 25
240V AC ECD & CR & 240V AC SR 1
3200A 32
240V AC ECD & CR & 24V DC SR 2
4000A 40
5000A 50 Version
6300A 63 Draw-out D
Fixed F
Selection for No. of Poles

(1) 3 Pole X
Selection for Breaking Capacity (Icu=Ics)
4 Pole 100% N F
50kA (Fr-I upto 2000A & Fr-2 2500A) N
4 Pole 50% N (in Fr-III only) H
65kA (Fr-I & Fr-II) S
4 Pole 200% N (upto 2500A) D
80kA (Fr-l, Fr-II & Fr-III) H
100kA (Fr-III) V (4)
For Fr-1, 2500A selection, please contact the nearest branch office
(5)
Refer point 'C' of Draw-out version Omega ACBs
Please Note : (6)
(1) For system requiring 690V metering, kindly order separate
For Icw values please refer product catalogue
(2) Power Metering module with MTX3.5
Other options of control voltage are available as accessory (7)
(3) For Operational Voltage 800V(M-Medium) & 1000V(H-High) requirements
Temperature protection is available in UW-MTX3.5/3.5EC/3.5H/4.5
14th digit to be used. For standard Breaker (upto690V) CAT No.
configuration remain as it is of 13 digit.
ACBs are offered with following standard features:
Draw-out version : Omega ACBs with UW-MTX release will have inbuilt-
Current Metering (MTX1.5G/1.5Gi/3.5/3.5EC/3.5H/4.5), Common Fault Indication microswitch, 4NO+4NC Aux. contacts, Smart-racking
shutter, Safety shutter assembly, Racking Handle, Door sealing frame, Pad-locking arrangement for ON/OFF button, Rating Error Preventer,
Arc shield.
A) For ratings upto 1600A, one side vertical terminal adaptors (Bottom) for Frames 1, 2 & 3.
B) For ratings 2000A & above, both side vertical terminal adaptors (Top & Bottom) for Frames 1, 2 & 3.
C) For ratings 4000A (Fr2 & Fr3) & 5000A(Fr3) replace 13th digit of ACB cat no with (recommended for Buscoupler only)
X : For Top Horizontal (Long) & Bottom Vertical for Fr2 & Fr3
Y : For Top & Bottom Horizontal (Long) for Fr3. H-H Termination not recommended for 4000A Fr2.
D) For rating 4000A & above, operation counter inbuilt for Frames 2 & 3 both.
Fixed Version : Omega ACBs with UW-MTX release will have inbuilt-
Current Metering (MTX1.5G/1.5Gi/3.5/3.5EC/3.5H/4.5), Common Fault Indication microswitch, 4NO+4NC Aux. contacts, Door sealing frame &
Pad-locking arrangement for ON/OFF push button.
A) For ratings upto 1600A, one side vertical terminal adaptors (Bottom) for Frames 1, 2 & 3.
B) For ratings 2000A & above, both side vertical terminal adaptors (Top & Bottom) for Frames 1, 2 & 3.
C) For ratings 4000A & above, operation counter inbuilt for Frames 2 & 3 both.
Electrically operated ACB includes ECD (240V AC), CR (240V AC) & SR (240V AC OR 24V DC).
Aimed at maximizing productivity, conserving energy, minimizing costs and enhancing safety, our
Electrical & Automation training programmes have benefitted over 1.77 Lakh professionals in the
last 38 years. These training programmes are highly beneficial as they provide right exposure and
impart knowledge on selection, installation, maintenance and testing of Electrical & Automation
Products.
So gain the advantage and go the extra mile with:

22 courses on contemporary topics
Courses applicable to all switchgear brands
Training Centers in Pune, Lucknow, Coonoor, Vadodara, Delhi & Kolkata
Blend of theory and practical experience
The typical training programmes cover:

Low Voltage & Medium Voltage Switchgear
Switchboard Electrical Design
AC Drives & Building Management Solutions
Protective Relays, Earthing, Reactive Power Management & Harmonics
Energy Conservation & Management
Please contact any of the training centres for participation and detailed training programme schedule.
Pune Lucknow Coonoor

Larsen & Toubro Limited Larsen & Toubro Limited Larsen & Toubro Limited
Switchgear Training Centre, Switchgear Training Centre, Switchgear Training Centre,
T-156/157, MIDC C - 6 & 7, UPSIDC Ooty-Coonoor Main Road
Bhosari, Pune - 411 026 P. O. Sarojininagar, Lucknow - 226 008 Yellanahalli P.O., The Nilgiris - 643 243
Tel: 020 2712 0037 / 2712 0653 Tel: 0522 247 6015 / 97944 54455 Tel. : 0423 251 7107
Fax: 020 2712 2933 Fax: 0522 247 6015 Fax : 0423 251 7158
E-mail: stc-pune@Lntebg.com E-mail: stc-lucknow@Lntebg.com E-mail: stc-coonoor@Lntebg.com
Vadodara Delhi Kolkata

Larsen & Toubro Limited Larsen & Toubro Ltd Larsen & Toubro Limited
Switchgear Training Centre Switchgear Training Centre Switchgear Training Centre
Behind L&T Knowledge City, 32, Shivaji Marg, 4th Floor, 3B, Shakespeare Sarani,
Near Village Ankhol, Near Motinagar Metro Station, Kolkata - 700071
Vadodara - 390019 New Delhi - 110015 Tel: 033 42005975 / 42005978
Tel: 0265 2457805 Tel: 011 41419515 / 41419695 / 41419500 E-mail: stc-kolkata@Lntebg.com
E-mail: stc-vadodara@Lntebg.com Fax: 011 41419600
E-mail: stc-delhi@Lntebg.com
Electrical Standard Products (ESP) Offices:
HEAD OFFICE Khairasol, Degaul Avenue L&T Business Park,

L&T Business Park, Durgapur 713 212 Tower 'B' / 3rd Floor
Tower 'B' / 3rd Floor Tel: 0343-2540448 / 2540449 / 2540443 Saki Vihar Road, Powai
Saki Vihar Road, Powai Fax: 0343-2540442 Mumbai 400 072
Mumbai 400 072 e-mail: esp-dgp@LNTEBG.com Tel: 022-67052874 / 2737 / 1156
Tel: 022-67053229 Fax: 022-67051112
Fax: 022-67051112 5, Milanpur Road, Bamuni Maidan e-mail: esp-bom@LNTEBG.com
e-mail: cic@LNTEBG.com Guwahati 781 021
Tel: +91 8876554417 12, Shivaji Nagar
BRANCH OFFICES Fax: 361-2551308 North Ambajhari Road
501, Sakar Complex I e-mail: esp-ghy@LNTEBG.com Nagpur 440 010
Opp. Gandhigram Rly. Station Tel: 0712-2260012 / 6606421
Ashram Road II Floor, Vasantha Chambers Fax: 2260030 / 6606434
Ahmedabad 380 009
5-10-173, Fateh Maidan Road e-mail: esp-nag@LNTEBG.com
Tel: 079-66304006-11
Hyderabad 500 004
Fax: 079-66304025
e-mail: esp-ahm@LNTEBG.com Tel: 040-67015052 32, Shivaji Marg
Fax: 040-23296468 P. O. Box 6223
38, Cubbon Road, P. O. Box 5098 e-mail: esp-hyd@LNTEBG.com New Delhi 110 015
Bengaluru 560 001 Tel: 011-41419514 / 5 / 6
Tel: 080-25020100 / 25020324 Monarch Building, 1st Floor Fax: 011-41419600
Fax: 080-25580525 D-236 & 237, Amrapali Marg e-mail: esp-del@LNTEBG.com
e-mail: esp-blr@LNTEBG.com Vaishali Nagar
Jaipur 302 021 L&T House
131/1, Zone II Tel: 0141-4385914 to 18 P. O. Box 119
Maharana Pratap Nagar Fax: 0141-4385925 191/1, Dhole Patil Road
Bhopal 462 011 e-mail: esp-jai@LNTEBG.com Pune 411 001
Tel: 0755-3080511 / 05 / 08 / 13 / 17 / 19 Tel: 020-66033395 / 66033279
Fax: 0755-3080502 Akashdeep Plaza, 2nd Floor Fax: 020-26164048 / 26164910
e-mail: esp-bho@LNTEBG.com P. O. Golmuri e-mail: esp-pnq@LNTEBG.com
Jamshedpur 831 003
Plot No. 559, Annapurna Complex Jharkhand Crystal Tower,
Lewis Road Tel: 0657-2312205 / 38 4th Floor, G. E. Road
Bhubaneswar 751 014 Fax: 0657-2341250 Telibandha
Tel: 0674-6451342 / 2436690 / 2436696 e-mail: esp-jam@LNTEBG.com Raipur - 492 006
Fax: 0674-2537309 Tel: 0771-4283214
e-mail: esp-bsr@LNTEBG.com Skybright Bldg; M. G. Road e-mail: esp-raipur@LNTEBG.com
Ravipuram Junction, Ernakulam
Aspire Towers, 4th Floor Kochi 682 016 3rd Floor
Plot No. 55, Phase-I Tel: 0484-4409420 / 4 / 5 / 7 Vishwakarma Chambers
Industrial & Business Park Fax: 0484-4409426 Majura Gate, Ring Road
Chandigarh-160 002
e-mail: esp-cok@LNTEBG.com Surat 395 002
Tel: 0172-4646840 / 41 / 42 / 46 / 53
Fax: 0172-4646802 Tel: 0261-2473726
Email: esp-chd@Lntebg.com 3-B, Shakespeare Sarani Fax: 0261-2477078
Kolkata 700 071 e-mail: esp-sur@LNTEBG.com
L&T Construction Campus Tel: 033-42005982
TC-1 Building, II Floor Fax: 033-22821025 / 7587 Radhadaya Complex
Mount-Poonamallee Road e-mail: esp-ccu@LNTEBG.com Old Padra Road
Manapakkam Near Charotar Society
Chennai 600 089 A28, Indira Nagar, Faizabad Road Vadodara 390 007
Tel: 044-2270 6800 Lucknow 226 016 Tel: 0265-6613610 / 1 / 2
Fax: 044-22706940 Tel: 0522-4929905 / 04 Fax: 0265-2336184
e-mail: esp-maa1@LNTEBG.com Fax: 0522-2311671 e-mail: esp-bar@LNTEBG.com
e-mail: esp-Lko@LNTEBG.com
67, Appuswamy Road Door No. 49-38-14/3/2, 1st floor,
Post Bag 7156 No: 73, Karpaga Nagar, 8th Street NGGO's Colony, Akkayyapalem,
Opp. Nirmala College K. Pudur Visakhapatnam - 530 016
Coimbatore 641 045 Madurai 625 007 Tel: 0891-2791126 / 2711125
Tel: 0422-2588120 / 1 / 5 Tel: 0452-2567405 / 2561068 / 2561657 Fax: 0891-2791100
Fax: 0422-2588148 Fax: 0452-2567552 Email: esp-viz@LNTEBG.com
e-mail: esp-cbe@LNTEBG.com e-mail: esp-mdu@LNTEBG.com
Product improvement is a continuous process. For the latest information and special applications, please contact any of our offices listed here.
Larsen & Toubro Limited, Electrical Standard Products

Powai Campus, Mumbai 400 072
Customer Interaction Center (CIC)

BSNL / MTNL (toll free) : 1800 233 5858 Reliance (toll free) : 1800 200 5858
Tel : 022 6774 5858
E-mail : cic@Lntebg.com / Website www.Lntebg.com
Registered Office: L&T House, N. M. Marg, Ballard Estate, Mumbai 400 001, INDIA CIN: L99999MH1946PLC004768
SP 50567 R5
Copyright © 04/2017 Larsen & Toubro. All Rights Reserved.

Omega Acb Catalogue PDF

Uploaded by

Copyright:

Available Formats

Omega Acb Catalogue PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Omega Acb Catalogue PDF

Uploaded by

Copyright:

Available Formats

Safeguard your systems

from electrical turbulence

Awarded ‘Overall Best Product

L&T -The bedrock of stability.

1) MTX1.0 - LSI Protection

To find the perfect OMEGA ACB to protect your

13 Air Circuit Breakers

25 Matrix Protection & Control Units

83 Control Circuit Wiring

91 Mounting & Termination

132 ACB Ordering Information

Ue Ics = Icu Ics = Icu

Breaking Capacities: Icu = Ics = Icw

Note: 400A & 630A versions also available.

Rated Operational Voltage at 50/60 Hz. Ue upto 690V AC

Rated Insulation Voltage at 50/60 Hz. Ui 1000V AC

Suitability for Isolation Yes

Degree of Protection on Breaker front IP53 Standard, IP54 Optional

Degree of Impact Protection on Breaker front IK08 Standard, IK10 Optional

Pollution Degree Suitability 4

Compliance IS / IEC 60947 (Part-2), EN 60947-2, IEC 60947-2

Operational Temperature Range O O

415/440V AC 50 65 80 65 80 50 65 80 80 100 80 100

0.5sec 50 65 80 65 80 50 65 80 80 100 80 100

Break Time (ms) 25

Closing Time (ms) 60

With Specific maintenance 20000 15000 10000

Width 3P 347 447 647

H (mm) Height 430

H (mm) Height 433

Version N-08 N-10

Rated Operational Voltage at 50/60 Hz. Ue 800V AC 1000V AC

Rated Insulation Voltage at 50/60 Hz. Ui 1250V AC

Suitability for Isolation Yes

Degree of Protection on Breaker front IP53 Standard, IP54 Optional

Degree of Impact Protection on Breaker front IK08 Standard, IK10 Optional

Pollution Degree Suitability 4

Compliance IS / IEC 60947 (Part-2), EN 60947-2, IEC 60947-2

Rated Ultimate S.C. 800V AC 50 50

Rated Service S.C. 800V AC 100% Icu 100% Icu

0.5 sec 50kA, 800V AC 50kA, 1000V AC

3.0 sec 50kA, 800V AC 50kA, 1000V AC

800V AC 105 105

Break Time (ms) 25 25

Closing Time (ms) 60 60

Width 3P 347 447 647 447

H (mm) Height 430

H (mm) Height 433

(1) Value corresponds operating cycle

Rating Specification Parameters for 50% N ACB

Rating Specification Parameters for 200% N ACB

UV Release Closing Release Shunt Release

2a - Type designation for Electrical

24b Lifting Location on Breaker

Superior Safety & Security:

a) Main spring is charged

3) Option of both Modbus & Profibus industrial communication protocols

7) Directional & Double Short-circuit protection

8) Password protection in releases prevents unauthorized access to protection release

Switchable neutral overload 10%In

Harmonics metering up to 27th Self-powered protection