Creo2 HW Notes
Creo2 HW Notes
Platform Support
System Requirements
Graphics Information
Due to the inherent hardware memory limitations of 32-bit platforms, PTC will no longer offer technical support for “out of memory conditions”
on 32-bit hardware for Creo 2.0 in cases where /3GB switch is utilized. Customers planning on upgrading to Creo 2.0 must carefully examine
whether their current 32-bit hardware will be adequate for their large assembly needs and consider switching to 64-bit hardware.
Graphics Information
For 3D-hardware acceleration, an OpenGL graphics card must be used that has been tested in a PTC-certified configuration. To ensure the
compatibility of a graphics driver with Creo 2.0, a PTC certified or supported hardware configuration is recommended. Graphics cards that
support at least OpenGL 3.1 are recommended for Creo 2.0.
PTC recognizes that customers can benefit from using latest graphics driver and performance optimizations and improvements made by
PTC’s Graphics Hardware Partners. With new workstations being continuously certified by PTC, the most current graphics drivers used in the
certification process can now be re-applied to previously certified configurations, as long as the configuration belongs to the same combination
of workstation and graphics hardware families.
For users of Direct3D on Windows 7, the March 2009 or later release of the DirectX 10.0 End User Run Time libraries
must be installed. Additionally, Medium to High-End graphics cards that fully support Direct3D 10.0 are recommended for adequate
performance. Visit the Microsoft website for more information about downloading and installing Direct3D.
Dual Monitor Support
Limited dual monitor support is provided in Creo 2.0. PTC has successfully performed limited testing of some graphics card models from AMD
and NVIDIA that support dual monitor capabilities. If your graphics card is certified for Creo 2.0 and provides dual monitor support**, PTC
expects that it will run in this mode without issue. PTC will provide limited support to resolve issues arising when running in dual monitor mode,
however, the entire solution will not be submitted for formal certification as a complete configuration.
Note: In the event that dual monitor mode fails, we advise use of Span mode as a workaround.
**Consult with AMD, NVIDIA, or the hardware platform partner to confirm the availability of this functionality with a given graphics card that has
been certified with Creo 2.0.
PTC provides Customer Support for all certified and supported graphics cards. Graphics cards are part of a fully-certified or supported
configuration (such as a workstation model, operating system, graphics card, graphics card driver).
PTC does not certify or support graphic cards independently from the configurations in which they are certified or supported. Refer to the
official PTC Platform Support web page for specific hardware partners and available configurations.
Additional certified and supported workstation hardware information will be added to the PTC Platform Support web page as our hardware
partners complete certifications in preparation for production Creo 2.0 shipment.
PTC has certified the following PTC Creo Applications to work in Virtualized Desktop Environments:-
Refer to the official PTC Platform Support web page for specific hardware partners and available configurations.
Supported Peripherals and Accessories
Emulation
Various manufacturers produce printers and plotters that may be compatible with or emulate a device that use a format which is supported
by PTC. Most devices are not specifically tested by PTC and therefore, may not produce correct plotted output. PTC Technical Support will
attempt to provide support for any printer which is using a standard supported format, but only to the extent of verifying the output to a
previously tested and readily available printer. Any support pertaining to the correctness of emulation can only be made by the
manufacturers of the device in question, and not by PTC.
The Microsoft Printer Manager creates an emulation of what appears on the screen and attempts to print this. Since this emulation is
between the Print Manager driver and the printer/plotter driver, quality and results may vary.
Creo Elements/Direct
Platforms CATIA (English only) Unigraphics (English only)
(all languages)
32-bit Windows XP, Windows 7 18.1 n/a NX7
64-bit Windows XP, Windows 7 18.1 n/a NX7
You can integrate several Finite Element Solvers with Creo 2.0 for use in FEM mode. The following table lists the supported Finite Element
Solvers and platforms.
Platform
Import / Export
Windows 32-bit
Windows 64-bit
Processor Format
Image Formats
BMP *.bmp – Edit via Image Editor, used in style feature as trace sketch, export parts and
assemblies via Distributed Pro/BATCH I/E Yes Yes
EPS *.eps – Save a Copy of parts and assemblies, export parts and assemblies via
E Yes Yes
Distributed Pro/BATCH
GIF *.gif – import via Image Editor, used in style feature as trace sketch I Yes Yes
HDR *.hdr – import via Image Editor I Yes Yes
JPEG *.jpg – Edit via Image Editor, used in style feature as trace sketch, Save a Copy of parts
I/E Yes Yes
and assemblies, export parts, assemblies and drawings via Distributed Pro/BATCH
PDF *.pdf – Save a Copy of parts, assemblies and drawings, export parts and assemblies via
E Yes Yes
Distributed Pro/BATCH
Picture *.pic – Save a Copy of parts, assemblies and drawings E Yes Yes
PNG *.png – Edit via Image Editor, used in style feature as trace sketch I/E Yes Yes
PTC Bumpmap *.tx1 – Edit via Image Editor I/E Yes Yes
PTC Color Texture *.tx4 – Edit via Image Editor, used in style feature as trace sketch I/E Yes Yes
PTC Decal *.tx3 – Edit via Image Editor, used in style feature as trace sketch I/E Yes Yes
PTC Image *.imf – Edit via Image Editor, used in style feature as trace sketch I/E Yes Yes
RGB *.rgb – Edit via Image Editor, used in style feature as trace sketch I/E Yes Yes
RLA *.rla - Edit via Image Editor, used in style feature as trace sketch I/E Yes Yes
Session Texture *.mem – Import via Image Editor I Yes Yes
Shaded Image *.shd – Edit via Image Editor, Save a Copy of parts and assemblies I/E Yes Yes
SHIMA-SEIKI *.pic – Edit via Image Editor, used in style feature as trace sketch I/E Yes Yes
TGA *.tga – Edit via Image Editor, used in style feature as trace sketch I/E Yes Yes
TIFF *.tif – Edit via Image Editor, used in style feature as trace sketch, Save a Copy of parts,
I/E Yes Yes
assemblies and drawings, export parts and assemblies via Distributed Pro/BATCH
2D Formats
Adobe Illustrator *.ai I Yes Yes
CGM *.cgm I/E Yes Yes
DWG *.dwg I/E Yes Yes
DXF *.dxf I/E Yes Yes
IGES *.igs I/E Yes Yes
Medusa s.* – Format generated by UNIX on export
*.she – Format generated by Windows on export I/E Yes Yes
*.asc – (import)
PDF *.pdf – Direct drawing export E Yes Yes
Creo View *.ed (structure) & *.plt (drawing)
*.edz (compressed structure and drawings)
E Yes Yes
*.pvs (structure) & *.plt (drawing)
*.pvz (packaged structure and drawings)
STEP *.stp – (import/export)
I/E Yes Yes
*.step – (import)
Stheno *.tsh I/E Yes Yes
3D Formats
ACIS *.acs I/E Yes Yes
Autodesk Inventor *.iam, *.ipt
I Yes Yes
Requires installation of and licensing for Autodesk Inventor
CATIA V4 *.model – (import/export)
*.exp, *.session – (import) I/E Yes No
Requires Interface for CATIA II license
CATIA V5 *.CATPart
*.CATProduct
I/E Yes Yes
*.cgr - Facet Only
Requires Interface for CATIA V5 license
DWG *.dwg – with embedded ACIS I Yes Yes
DXF *.dxf – with embedded ACIS I Yes Yes
Granite *.g I/E Yes Yes
JT *.jt
I/E Yes Yes
Requires Interface for JT license
IBL *.ibl I Yes Yes
ICEM *.icm I Yes Yes
IGES *.igs – (import/export)
I/E Yes Yes
*.iges – (import)
Neutral *.neu I/E Yes Yes
Optegra visualize *.gbf Facet Only E Yes Yes
Parasolid 3D *.xmt, *.xmt_txt, *.x_t, *.xmt_neu, *.x_n *.xmt_bin, *.x_b – (import)
I/E Yes Yes
*.x_t – (export)
PDF *.pdf – Direct model export E Yes Yes
Points *.pts I Yes Yes
Creo Elements/View & *.ed (structure) & *.ol (models)
Creo View *.edz (compressed structure and models)
I/E Yes Yes
*.pvs (structure) & *.ol (models)
*.pvz (packaged structure and models)
Render *.slp – Facet Only E Yes Yes
Rhino *.3dm I Yes Yes
SolidWorks *.sldprt, *.sldasm
I Yes Yes
Requires installation of SolidWorks or SolidWorks Explorer and a license of SolidWorks.
STEP *.stp – (import/export)
I/E Yes Yes
*.step – (import)
STL *.stl – Facet Only I/E Yes Yes
U3D *.u3d E Yes Yes
Unigraphics *.prt (UG format)
I/E Yes Yes
Requires UG license and installation
VDA *.vda I/E Yes Yes
VRML *.wrl – Facet Only I/E Yes Yes
Wavefront *.obj I Yes Yes
ECAD Formats
Allegro *.mdb – For board outline files
*.mdc – For component placement files I/E Yes Yes
*.mdf – For footprint files, such as the ones in component outline libraries
DAZIX *.edn – Neutral file of the board outline and component placement. Dazix refers to this
as a core file. I/E Yes Yes
*.edp – Profile file that contains component outlines. Dazix refers to this as a library file
EDMD *.idx I/E Yes Yes
IDF *.emn – (import/export)
I/E Yes Yes
*.emp – library file (import)
Neutral *.nwf I/E Yes Yes
Creo Schematics *.xml I Yes Yes
Visula *.evs I/E Yes Yes
NOTES
Object Linking and Embedding (OLE) may provide additional format support but is dependent on operating system, installed software
components, and third-party support for OLE.