Ordering number : ENA0315

Monolithic Linear IC
Audio Output for TV application
LA42072 7W × 2ch Power Amplifier

Overview
LA42072 is 7W 2-channel AF power amplifier intended for televisions.

Functions
• 7W × 2 channel (VCC = 12V, RL = 8Ω).
• Standby function.
• Mute function.
• Thermal protection circuit.

LA42000 series is power IC which made Pin compatible altogether in 5 to 15W. They consist of four kinds of power ICs
(mono, stereo, mono with volume function, stereo with volume function. They realized PCB layout communalization of an
audio power block of TV).

Channel
Model name PO Volume
Monaural Stereo
LA42051 5W {
LA42052 5W {
LA42351 5W { {
LA42352 5W { {
LA42071 7W {
LA42072 7W {
LA42152 15W {

Maximum Ratings at Ta = 25°C

Parameter Symbol Conditions Ratings Unit
Maximum supply voltage VCC max No signal 24 V
Allowable power dissipation Pd max Infinite heat sink 15 W
Maximum junction temperature Tj max 150 °C
Thermal resistance θjc 3 °C/W
Operating temperature Topr -25 to +75 °C
Storage temperature Tstg -40 to +150 °C

Any and all SANYO Semiconductor products described or contained herein do not have specifications
that can handle applications that require extremely high levels of reliability, such as life-support systems,
aircraft's control systems, or other applications whose failure can be reasonably expected to result in
serious physical and/or material damage. Consult with your SANYO Semiconductor representative
nearest you before usingany SANYO Semiconductor products described or contained herein in such
applications.
SANYO Semiconductor assumes no responsibility for equipment failures that result from using products
at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor
products described or contained herein.

83006 / 42706 MS JK B8-7230 No.A0315-1/5

 LA42072
Operating Conditions at Ta = 25°C
Parameter Symbol Conditions Ratings unit

Recommended supply voltage VCC 12 V

Recommended load resistance RL 8 Ω
Allowable operating voltage range VCC op 5.5 to 20 V

Electrical Characteristics at Ta = 25°C, VCC = 12V, RL = 8Ω, f = 1kHz, Rg = 600Ω

Ratings
Parameter Symbol Conditions Unit
min typ max
Standby current IST Amplifier off 0 10 µA
Quiescent current ICCO Rg = 0 40 70 150 mA
Output power PO THD = 10% 6 7 W
Total harmonic distortion THD PO = 1W 0.06 0.2 %
Voltage gain VG VO = 0dBm 33 35 37 dB
Output noise voltage VNO Rg = 0, BPF = 20Hz to 20kHz 0.1 0.3 mVrms
Ripple rejection SVRR Rg = 0, fR = 100Hz, VCCR = 0dBm 50 60 dB
Channel separation CH.Sep Rg = 10kΩ, VO = 0dBm 50 60 dB
Mute Attenuation ATT Vo=1Vrms,BPF=20Hz to 20kHz 80 90 dB
Mute ON 1.7 3.0 V
Mute control voltage (pin 6) Vmute
Mute OFF 0 0.5 V
Standby control voltage Amplifier on 2.5 20 V
VST
(The Pin 5 voltage) Amplifier off 0 0.5 V
Input resistance Ri 14 20 26 kΩ

Package Dimensions
unit : mm
3107B

25.6 2.4
3.0 min

C0.7 3.4 (10.0) ( 2.0)

15.4max
(13.9)

(11.8)
11.2

4.5
1.0 min

1 13
0.5 1.15 0.4
2.0 1.2
(0.8)

SANYO : SIP13H

No.A0315-2/5
 LA42072
Block Diagram

Application Circuit Example

No.A0315-3/5
 LA42072
External Components

C1,C2 : Input coupling capacitors, which are recommended to be 4.7µF or less. The input circuit is of a zero bias
type, so that the input pin potential is close to zero volts. Therefore, the polarity must be determined
depending on the DC potential of a circuit connected in the previous stage of LA42072.
C3 : Capacitor for the starting time of ripple filter and amplifier, which is recommended to be 47µF.
C4,R1 : Capacitor and resistor for muting. C4 is necessary even when no muting function is provided.
C5 : Power supply capacitor.
C6 to C9 : Capacitors and resistors for prevention of oscillation. For C6 to C9, polyester film capacitors. and having
R2 to R5 satisfactory temperature characteristics are recommended. Uses 2.2Ω resistor together.

1. Muting function (Pin 6)

Mute ON when the voltage of pin 6 is 1.7V (min) or more.
Set the VM application voltage so that the voltage of pin 6 becomes 1.7V or more.
The time constant of mute is determined with R1 and C4. The constant must be determined after review because it is
concerned with the pop sound at mute ON/OFF. C4 is concerned with the pop sound also when the amplifier is turned
ON, so that this is necessary even when the mute function is not used.

Example: The voltage of pin 6 becomes about 1.8V under conditions of VM = 5V and R1 = 15kΩ.

2. Standby function (Pin 5)

The amplifier is turned ON when the voltage of 2.5V (min) or more is applied to pin 5.

Control Voltage of pin 5

Pin 5 voltage Amplifier Standby
0 to 0.5V OFF ON
2.5 to 20V ON OFF

To suppress 5 pin inflow current when the impressed voltage of

VSTB is high, limitation resistance (RSTB) is inserted.

Example: Limiting the inrush current to pin 5 to 500µA or less

Application voltage (VSTB) − 2VBE(about 1.4V)

RSTB= − 15kΩ
500µA

No.A0315-4/5
 LA42072
Usage Notes

1. Lightening (power supply - output short-circuit), ground fault (GND - output short-circuit), and load short-circuit protection
circuits are incorporated. These protection circuits are activated in case of abnormal connection.
These circuits are active while above abnormal connection continues and reset automatically when such abnormality is
removed.
Depending on operation conditions, the protective circuits remain locked and continue to be active even when abnormal
condition is removed. In this case, turn OFF standby or power supply temporarily and the protective circuits can be reset.

2. The thermal protective circuit is incorporated, which is activated when the junction temperature (Tj) rises to about 160°C or
more, controlling the output gradually to the attenuated condition.

3. During use near the maximum rating, the product may suffer damage if even the slightest fluctuation of condition exceeds the
maximum rating. Be sure to use the product within a range which never exceeds the maximum rating while allowing
sufficient margin for the supply voltage, etc.

Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the
performance, characteristics, and functions of the described products in the independent state, and are
not guarantees of the performance, characteristics, and functions of the described products as mounted
in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an
independent device, the customer should always evaluate and test devices mounted in the customer's
products or equipment.
SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any
and all semiconductor products fail with some probability. It is possible that these probabilistic failures
could give rise to accidents or events that could endanger human lives, that could give rise to smoke or
fire, or that could cause damage to other property. When designing equipment, adopt safety measures
so that these kinds of accidents or events cannot occur. Such measures include but are not limited to
protective circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO Semiconductor products (including technical data,services) described
or contained herein are controlled under any of applicable local export control laws and regulations, such
products must not be exported without obtaining the export license from the authorities concerned in
accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or
otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO Semiconductor product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not
guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and
reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual
property rights or other rights of third parties.

This catalog provides information as of April, 2006. Specifications and information herein are subject
to change without notice.

PS No.A0315-5/5