MVS Catalog

Low Voltage
EasyPact MVS
LV power circuit breakers and switch-disconnectors

800 to 4000A
Catalogue
2013
Performance
without compromise
Exceptional Quality and safety Outstanding value for an

reliability,flexibility you can trust optimized feature set
and convenience
Buildings Industry Panelbuilders

EasyPact MVS range
The easy choice for reliable performance
> Performance without compromise

> Assured quality and safety you can trust
> Deliver exceptional reliability and flexibility in its class
> Outstanding value for an optimized feature set
> Precision engineered to meet your needs
> Unbeatable value throughout its lifecycle
> Simple to choose and easy to install
3
Choose the leader
> 800 to 4000A ratings

> Breaking capacity: 50 & 65kA
> Suitable for 690V applications
> Complete selectivity with Ics=Icu=Icw (1 s)
> Intelligent ET range of trip system with display
> Fully protected neutral on 4 pole breakers
> Common accessories for complete range
> Conforms to IEC 60947- 2 & 3
EasyPact MVS
Benefits for every
customer
EasyPact MVS08 to MVS40
Panel builders/ End Users Designers

contractors
> Single frame size from 800 to 4000A > Moulded case design ensures high > Conforms to IEC60947-2 for breakers &
with identical door cut-outs endurance without maintenance IEC60947-3 for disconnectors
> Suitable for copper & Aluminium > Intelligent ET range of trip system > Designed and manufactured using
termination with a single pole pitch of with thermal memory and display for advanced manufacturing methods to
115 mm measurements. match your quality expectations and
> Terminal orientation can be converted > Overload run alarm & individual LED the needs of each project.
from horizontal to vertical and vice- indications enable fault identification > Continuous rated coils helps in simple
versa at workshop > lcu=lcs=lcw(1sec)=50kA & 65kA interlocking schemes
> Direct mounting Door frames ensures complete selectivity > Extensive choice of software tools &
(escutcheon) without drilling any holes > Inbuilt safety shutter & interlocks documentation to reduce design time.
> Front fitted accessories like under-volt > Designed to provide utmost user > EasyPact MVS respects the
release, shunt release & closing coil safety during installation, during use, environment throughout their life cycle
for complete range and while under maintenance.
> Conversion of manual operated > All 4 pole breakers are with fully rated EasyPact MVS is designed to meet the
breaker in to electrical operated, with neutral and protected with adjustable needs of your customers with flexibility
single bolt fixing settings at OFF – 50%-100% to achieve system efficiency during the
design phase
EasyPact MVS with single EasyPact MVS answers even to the
frame size,common accessories most stringent application with most
helps to increase the shop floor reliable distribution systems assuring
efficiency,enabling faster delivery of continuity of service
swith boards.
5
The Key values
90%
The performance you need
EasyPact MVS provides the ideal level of capability for
re
ations a
your installation from 800 to 4000 A.
of a p p li c
covered
ock by up to
educe st At a cost-effective investment
30%
R
Pay for what you need: Get outstanding durability with

the features you need, with the benefit of easy to order
and stock.
100% With the quality you demand

Designed and manufactured by Schenider Electric using
ment to
advanced manufacturing methods and premium mate
Commit rials.
quality
6
Gain peace of
mind and
optimised cost
for every
installation
EasyPact MVS General contents
Functions A-1
and characteristics
Installation
B-1
recommendations
Dimensions
C-1
and connection
Electrical diagrams D-1
Additional
E-1
characteristics
Catalogue numbers
F-1
and order form

Functions
and characteristics
EasyPact MVS Functions and characteristics
General overview A-2
Detailed contents A-2
Circuit breakers and switch-disconnectors A-4
MVS08 to MVS40 A-4
Identifying ET range of trip system A-6

Overview of functions A-8
ET trip system A-8
ETA trip system A-10
ETV trip system A-12
ET range of trip system A-14
Accessories and test equipment A-14
Connections A-15
Overview of solutions and accessories A-15
Accessories and auxiliaries A-16
Locking A-18
On the device A-18
On the chassis A-19
Indication contacts A-20

Remote operation A-21
Remote ON / OFF A-21
Remote tripping A-23
Source-changeover systems A-24
Mechanical interlocking A-24
Accessories A-25
Installation recommendations B-1
Dimensions and connection C-1
Additional characteristics E-1
Catalogue numbers and order form F-1
A-1
Functions General overview
and characteristics Detailed contents
This overview describes all the functions offered by Circuit breakers and switch-disconnectors page A-4
EasyPact MVS devices.
b Ratings:
v EasyPact MVS 800 to 4000 A
b Circuit breakers type N, H
b Switch-disconnectors type NA, HA
CPB100000
b 3 or 4 poles
b Fixed or drawout versions
ET trip system page A-8

b 2I basic protection
b 5S selective protection
b 6G selective + earth-fault protection
b Standard long-time rating plug:
v Current setting (A) 0.4 to 1 x In
ETA trip system with current measurement page A-10

CDB500000
CDB500001
CDB500002
ET2I Trip System

ET6G Trip System ET5S Trip System
ET6G Trip System ET6G Trip System
ET6G Trip System
b External power-supply module
ETV trip system with voltage measurement page A-12

long time
long time
alarm long time
long time long time
long time
b
Ir alarm alarm alarm
External power-supply module

.8 tr 8 Ir tr alarm Ir tr alarm
.7 .9 (s)
(s) 4
12 .8 8 .8 8
.7
.9 (s)
(s) 4 12 .7 .9 (s)
(s) 4 12
.6 .95 2
16
.6 .95 2 16 .6 .95 2 16
.5 .98 1 20 .5
.98 1 20 .5 .98 1 20
.4 1 .5 24
.4 1 .5 24 .4 1 .5 24
x In at 6 Ir
[Ir x In at 6 Ir x In at 6 Ir
instantaneous [Ir [Ir
short time short time instantaneous short time instantaneous
short time instantaneous short time instantaneous
Isd Isd tsd Ii Isd tsd Ii
(s) .4 .4 .3
4 5 (s) (s)
4 5 (s) .4 .4 .3 4 5
Connections page A-15

3
3 8 10 3 8 10
6 6
2.5 6
2.5 6 .3 .2 4 12 2.5 6 .3 .2 4 12
2 8 2 8 .2 .1 3 15 2 8 .2 .1 3 15
1.5 10 1.5 10 on.1 2 0 off 2 off
off 1.5
10 on.1 2 0 off 2 off
off
x Ir on I t x In on I t x In
x Ir x Ir
test test
setting delay test
test
b Rear connection:
tg
(s)
Ig
D E F (s) .4 .4 .3
C G .3
.2
B
H .2 .1
on.1 2 0off
v
A I
Horizontal
on I t off
ground fault
ground fault
DB101149
E46459
v Vertical
ET2I trip system. ET5S trip system. ET6G trip system. b Optional accessories:
v Interphase barriers Safety shutters
v Safety shutters and shutter locking Interphase barriers
blocks
Locking page A-18

b Pushbutton locking by
DB101109
DB101110
padlockable transparent cover

b OFF-position locking by keylock
b Chassis locking in disconnected
position by keylock
b Chassis locking in connected,
disconnected and test positions Chassis key lock
b Door interlock (inhibits door
Door interlock
opening with breaker in
‘connected’ or ‘test’ position
A-2
Indication contacts page A-20
PB104354A40
b Standard:
E46438
DB101112
v ON/OFF indication (OF)
v “Fault” trip indication (SDE)
b Optional:
v Additional ON/OFF indication (OF)
v Ready-to-close contact (PF)

Ready-to
v Carriage switches for connected close contact
(CE) disconnected (CD) and test OF contact
(CT) positions
Remote operation page A-21

b Remote ON/OFF:
DB101113
DB101114
v Gear motor
CPB100003
v XF closing or MX opening
voltage releases
b Remote tripping function:
v MN voltage release
- Standard
- Adjustable or non-adjustable
delay
MX, XF and MN volage
releases
Gear motor
Accessories page A-25

b Auxiliary terminal shield
E46668
E46669
b Operation counter
b Escutcheon (Door sealing frame)
b Transparent cover for escutcheon
b Escutcheon blanking plate
CPB100015
Escutcheon Transparent cover

DB101115
Mechanical operation counter
Source-changeover systems page A-24

b Mechanical interlocking using cables:
CDB500053
v Interlocking between two devices

v Interlocking between three devices
CPB100016
Interlocking of two devices
A-3
Functions Circuit breakers
and characteristics
and switch-disconnectors
MVS08 to MVS40
Common characteristics
Number of poles 3/4
Rated insulation voltage (V) Ui 1000
Impulse withstand voltage (kV) Uimp 12
Rated operational voltage (V AC 50/60 Hz) Ue 690
Suitability for isolation IEC 60947-2 Yes
Degree of pollution IEC 60664-1 4
Basic circuit-breaker
CPB100000
Circuit-breaker as per IEC 60947-2

Rated current (A) In at 40°C(1)
Rating of 4th pole (A)
Sensor ratings (A)
Type of circuit breaker
Ultimate breaking capacity (kA rms) Icu 220...440V
V AC 50/60 Hz 690 V
Rated service breaking capacity (kA rms) Ics % Icu
Utilisation category
Rated short-time withstand current (kA rms) Icw 1s 220...440 V
V AC 50/60 Hz 690V
3s 440/690V
Circuit breaker. Rated making capacity (kA peak) Icm 220...440 V
V AC 50/60 Hz 690 V
Breaking time (ms) between tripping order and arc extinction
Closing time (ms)
Switch-disconnector as per IEC60947-3 and Annex A
CPB100014
Type of switch-disconnector
Operational current AC23A
Rated making capacity (kA peak) Icm
Rated short-time withstand current (kA rms) Icw 1s
3s
Maintenance/Connection/Installation
Service life Mechanical with maintenance
C/O cyclesx1000 without maintenance
Electrical without maintenance 440 V
690 V
Connection Horizontal
Switch disconnector. Vertical
Dimensions (mm) Drawout 3P
(H x W x D) 4P
Fixed 3P
4P
Weight (kg) Drawout 3P/4P
(approximate) Fixed 3P/4P
(1) Refer page no. B-12 for details on temperature derating.
A-4
MVS08 MVS10 MVS12 MVS16 MVS20 MVS25 MVS32 MVS40
800 1000 1250 1600 2000 2500 3200 4000

800 1000 1250 1600 2000 2500 3200 4000
800 1000 1250 1600 2000 2500 3200 4000
N H N H N H N H N H N H N H N H
50 65 50 65 50 65 50 65 50 65 50 65 50 65 55 65
42 50 42 50 42 50 42 50 42 50 42 50 42 50 42 50
100% 100% 100% 100% 100% 100% 100% 100%
B B B B B B B B
50 65 50 65 50 65 50 65 50 65 50 65 50 65 55 65
42 50 42 50 42 50 42 50 42 50 42 50 42 50 42 50
25 36 25 36 25 36 25 36 25 36 25 36 25 36 30 36
105 143 105 143 105 143 105 143 105 143 105 143 105 143 121 143
88 105 88 105 88 105 88 105 88 105 88 105 88 105 88 105
25 25 25 25 25 25 25 25
<70 <70 <70 <70 <70 <70 <70 <70
MVS08 MVS10 MVS12 MVS16 MVS20 MVS25 MVS32 MVS40
NA HA NA HA NA HA NA HA NA HA NA HA NA HA NA HA
800 1000 1250 1600 2000 2500 3200 4000
105 143 105 143 105 143 105 143 105 143 105 143 105 143 121 143
50 65 50 65 50 65 50 65 50 65 50 65 50 65 55 65
25 36 25 36 25 36 25 36 25 36 25 36 25 36 30 36
20 20 20 20 20 20 20 20
10 10 10 10 10 10 10 10
6000 6000 6000 6000 6000 5000 5000 5000
4000 4000 4000 4000 4000 2500 2500 2500
Yes
Yes
439 x 441 x 395
439 x 556 x 395
352 x 422 x 297
352 x 537 x 297
70/85 90/120
40/50 60/80
A-5
Functions Identifying ET range of
and characteristics
trip system
EasyPact MVS circuit breakers equipped with ET range Dependability

of trip system are designed to protect power circuit and Integration of protection functions in an ASIC electronic component used in all trip
connected loads. units guarantees a high degree of reliability and immunity to conducted or
Measurement of current and voltage helps users to radiated disturbances.
maintain continuity of service and optimize installation. On ET range, measurement functions are managed by an independent
microprocessor. Protection functions are independent of measurement functions,
CPB100011
ensure system protection even at very low load currents.
Accessories
Certain functions require the addition of trip unit accessories, described on
page A-14.
Trip unit name codes ET2I: basic protection

Type of protection
DB101116
b 2I for basic protection Protection:

b 5S for selective protection long time
b 6G for selective + earth-fault protection + instantaneous
Type of measurement
b ET for basic
b ETA for “Current”
b ETV for “Current” and “Voltage”
ET5S: selective protection

DB101117
Protection:
long time
+ short time
+ instantaneous
ET6G: selective + earth-fault protection

DB101117
DB101118
Protection:
long time
+ short time
+ instantaneous
+ earth fault
A-6
Protection and measurement functions
ET ETA ETV
b Fault indications b I1, I2, I3, IN, Iearth-fault, and maximeter for b Incorporates all the rms measurements of ETA trip
b Settings in amperes and in seconds these measurements: unit, plus voltage readings:
v Fault indications v Calculates the current demand value
v Settings in amperes and in seconds v “Quickview” function for the automatic cyclical
display of the most useful values
2I
2I
2I
CDB500028
CDB500000
CDB500035
ETA2I
ET2I Trip System 2I
ET6G Trip System
long time
long time long time
long time
Ir .8
tr 8
alarm
alarm Ir tr alarm
alarm
.7
.9
(s)
(s) 4
12
.8 8
.7
.9
(s)
(s) 4
12
.6 .95 2 16
.6 .95 2 16
.5 .98 1 20 .5 .98 1 20 long time
long time
.4
x In
1 .5
at 6 Ir
24 .4
x In
1 .5
at 6 Ir
24 Ir .8 tr 8
alarm
alarm
[Ir .7 .9 (s)
(s) 4
instantaneous [Ir 12
instantaneous
short time instantaneous .6 .95 2 16
Isd I i
4 5 8 10 .5 .98 1 20
3 6
2.5 6 12 .4 1 .5 24
4 x In at 6 Ir
[Ir
2 8 3 15 instantaneous
1.5 10 2 off
off instantaneous
x Ir x In I i
8 10
test 6
4 12
3 15
2 off
off
x In
test
test
ground fault
5S
5S
5S
CDB500001
CDB500030
CDB500029
ET5S Trip System ETA5S ETV5S

ET6G Trip System
long time
long time
Ir tr alarm
alarm long time
long time long time
long time
.7
.8
.9
(s)
(s) 4
12 Ir tr alarm
alarm Ir .8
tr 8
alarm
alarm
.8 8
.7
.9
(s)
(s) 4
12
.6 .95 2
16 .7
.9
(s)
(s) 4 12
.6 .95 2 16
.6 .95 2 16
.5 .98 1 20
.4 1 .5 24 .5 .98 1 20 .5 .98 1 20
x In at 6 Ir .4 1 .5 24
[Ir .4 1 .5 24 x In at 6 Ir
short time instantaneous x In at 6 Ir

[Ir [Ir
short time instantaneous instantaneous
Isd tsd Ii short time instantaneous short time
short time instantaneous
4 5 (s)
(s) .4 .4 .3 8 10 short time instantaneous
Isd tsd I i
3 6 Isd tsd Ii (s)

.2 4 5 (s)
(s) .4 .4 .3 8 10 3
4 5 (s) .4 .4 .3
8 10
2.5 6 .3 4 12 3 6 6
2 8 .2 .1 3 15 2.5 6 .3 .2 4 12 2.5 6 .3 .2 4 12
.2 .1
on.1
10 0off 2 off
off 2 8 . 2 .1 3 15
2 8 3 15
1.5 2
on.1
x Ir
on I t x In .1 0off off
off 1.5 10 2 0off 2 off
off
1.5 10 on 2 2 on I t
on I t x In x Ir x In
test x Ir
test test
ground fault
6G
6G
6G
CDB500002
CDB500003
CDB500004
ET6G Trip System

ET6G Trip System
long time
long time
Ir tr alarm
alarm long time
long time
.7
.8
.9
(s)
(s) 4
8
long time
long time Ir tr alarm
alarm
12
alarm .8
8
Ir .8
tr 8
alarm .7
.9
(s)
(s) 4
12
.6 .95 2
16
.7
.9
(s)
(s) 4 12 .6 .95 2 16
.5 .98 1 20 .6 .95 2 16
.5 .98 1 20
.4 1 .5 24
.5 .98 1 20
x In at 6 Ir
[Ir .4 1 .5 24
.4 1 .5 24
x In at 6 Ir
short time instantaneous x In at 6 Ir
[Ir
short time instantaneous [Ir short time instantaneous
Isd tsd Ii short time instantaneous
(s) .4 .4 .3
4 5 (s) short time instantaneous
8 10 Isd
tsd I i
(s) .4 .4
.3

3 6 4
5
(s) 8 10
6
.3
.2
12
Isd tsd
(s) .4 .4
.3
(s) I i
3
6
2.5
.1
4
4
5
8 10
6
.3
.2
12
2 8 .2 3 15
.3 .2
6
2.5 4
2.5 6 4 12 8 .2 .1 15
on.1
off 2 3
1.5 10
on
2
I
t
0off 2 off
2
8 .2 .1 3 15 10 .1 2 0 2 off
off
x Ir x In
.1
2 0 off
off
1.5 on
on I
t off x In
10
on 2
x Ir
on I t off
setting delay test
test
1.5
x Ir x In setting delay test
test
tg
(s)
Ig
D E F (s) .4 .4
.3
setting delay test tg
(s)
(s) .4 .4
.3
test Ig
.3 .2 tg
(s) D E F
.4 .4
.3 .2
C G Ig
.2
.1
D E F (s) C G .3
B H
C G .3 .2 B H .2 .1
A I on.1 2 0off
on I
t off B H .2
.1 A I on.1 2 0off
ground fault on I
t off
ground fault A I on.1 2
0off ground fault
on I
t off ground fault
ground fault
ground fault
A-7
Functions Overview of functions

and characteristics ET trip system
ET trip unit protect power circuits, under overload Protection

& short-circuit conditions. They are equipped with Protection thresholds and delays are set using the adjustment dials.
individual fault trip indication LEDs. ET6G provides Overload protection
earth-fault protection. True rms long-time protection.
Protects cables (phase and neutral) against overloads
Thermal memory(1): thermal image before and after tripping.
CDB500002
ET6G Trip System

ET6G Trip System Short-time protection
b The short-time protection function protects the distribution system against
impedant short-circuits
b The short-time tripping delay can be used to ensure discrimination with
downstream circuit breaker
b The I2t ON and I2t OFF options enhance discrimination with a downstream
protection devices
b Use of I2t curves with short-time protection:
v I2t OFF selected: the protection function implements a constant time curve
v I2t ON selected: the protection function implements an I2t inverse-time curve up to
10 lr. Above 10 lr, the time curve is constant
Earth-fault protection on ET6G trip system
Residual earth fault protection.
Selection of I2t type (ON or OFF) for delay.
A ground fault in the protection conductors can provoke local temperature rise at
the site of the fault or in the conductors. The purpose of the ground-fault protection
function is to eliminate this type of fault.
Type Description
Residual b The function determines the zero-phase sequence current, i.e. the
vectorial sum of the phase and neutral currents
b It detects faults downstream of the circuit breaker
Instantaneous protection
The Instantaneous-protection function protects the distribution system against solid
short-circuits. Contrary to the short-time protection function, the tripping delay for
long time
long time instantaneous protection is not adjustable. The tripping order is sent to the circuit
tr alarm
Ir
.7
.8
.9 (s)
(s) 4
8
12
alarm
breaker as soon as current exceeds the set value, with a fixed time delay of
.6 .95 2 16 7 20 milliseconds.
.5 .98 1 20
.4
x In
1 .5
at 6 Ir
24 Neutral protection
[Ir
short time
short time
instantaneous
instantaneous On three-pole circuit breakers, neutral protection is not possible.
Isd tsd Ii
3
4 5 (s) .4 .4 .3
(s)
6
8 10 On four-pole circuit breakers, neutral protection may be set using a three-position
2.5 6 .3 .2 4 12 switch: neutral unprotected (4P 3d), neutral protection at 0.5 Ir (4P 3d + N/2), neutral
2 8 .2 .1 3 15
1.5 10 on.1 2 0off 2 off
off protection at Ir (4P 4d).
on I t x In
x Ir
setting delay test
test
Zone selective interlocking (ZSI)
Ig
D E F
tg
(s)
(s) .4 .4 .3 A ZSI(2) terminal block may be used to interconnect a number of control units to
C G .3 .2 provide total discrimination for short-time and earth-fault protection, without a delay
B H .2 .1
A I on . 1 2 0off before tripping.
on I t off
ground fault
ground fault
Overload alarm
A yellow alarm LED goes on when the current exceeds the long-time trip threshold.
Fault indications
1 Long-time threshold and tripping delay.
LEDs indicate the type of fault:
2 Overload alarm (LED) at 1,125 Ir.

b Overload (long-time protection Ir)
3 Short-time pick-up and tripping delay.

b Short-circuit (short-time Isd or instantaneous li protection)
4 Instantaneous pick-up.
b Earth fault (Ig)
5 Earth-fault pick-up and tripping delay.
6 Earth-fault test button.
b Internal fault (Ap)
7 Long-time rating plug screw.

Battery power
8 Test connector.
The fault indicating LEDs are powered by an in-built battery. The fault indication
9 Lamp test, reset and battery test.
LEDs remain on until the test/reset button is pressed.

10 Indication of tripping cause.
Test
A hand-held test kit may be connected to the test connector on the front to check
circuit-breaker operation. For ET6G trip unit, the operation of earth-fault protection
(1) The thermal memory continuously accounts for the amount
of heat in the cables , both before and after tripping , whatever
can be checked by pressing the test button located above the test connector.
the value of the current(presence of an overload or not).The
thermal memory optimises the long-time protection function of
the circuit breaker by taking into account the temperature rise
in the cables .The thermal memory assumes a cable cooling
time of approximately 20 minutes.
(2) Refer to page D-5 for more details on ZSI.
Note: ET trip control units come with a transparent leadseal

cover as standard.
A-8
Protection ET2I
Long time ET2I
DB101126
Current setting (A) Ir = In x ... 0.4 0.5 0.6 0.7 0.8 0.9 0.95 0.98 1
Tripping between 1.05 and 1.20 x Ir
Time setting tr (s) 0.5 1 2 4 8 12 16 20 24
Time delay (s) Accuracy: 0 to -30 % 1.5 x Ir 12.5 25 50 100 200 300 400 500 600
Accuracy: 0 to -20 % 6 x Ir 0.7(1) 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 7.2 x Ir 0.7(2) 0.69 1.38 2.7 5.5 8.3 11 13.8 16.6
Thermal memory 20 minutes before and after tripping
(1) 0 to -40 % - (2) 0 to -60 %
Instantaneous
Pick-up (A) Isd = Ir x … 1.5 2 2.5 3 4 5 6 8 10
Accuracy: ±10 %
Time delay Max resettable time: 20 ms
Max break time: 80 ms
Protection ET5S/ET6G
Long time ET5S/ET6G
DB101127
Current setting (A) Ir = In x … 0.4 0.5 0.6 0.7 0.8 0.9 0.95 0.98 1
Time setting tr (s) 0.5 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 6 x Ir 0.7(1) 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 7.2 x Ir 0.7(2) 0.69 1.38 2.7 5.5 8.3 11 13.8 16.6
(1) 0 to -40 % - (2) 0 to -60 %
Short time
Pick-up (A) Isd = Ir x … 1.5 2 2.5 3 4 5 6 8 10
Accuracy: ±10 %
Time setting tsd (s) Settings I2t Off 0 0.1 0.2 0.3 0.4
I2t On - 0.1 0.2 0.3 0.4
Time delay (ms) at 10 x Ir tsd (max resettable time) 20 80 140 230 350
(I2t Off or I2t On) tsd (max break time) 80 140 200 320 500
Instantaneous
Pick-up (A) Ii = In x … 2 3 4 6 8 10 12 15 off
Accuracy: ±10 %
Earth fault ET6G
DB101128
Pick-up (A) Ig = In x … A B C D E F G H J
Accuracy: ±10 % In y 400 A 0.3 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
400 A < In y 1000 A 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
In u 1250 A 500 640 720 800 880 960 1040 1120 1200
Time setting tg (s) Settings I2t Off 0 0.1 0.2 0.3 0.4
I2t On - 0.1 0.2 0.3 0.4
Time delay (ms) tg (max resettable time) 20 80 140 230 350
at In or 1200 A (I2t Off or I2t On) tg (max break time) 80 140 200 320 500
Note: All current-based protection functions require no auxiliary source.
The test / reset button, clears the tripping indication and tests the battery.
A-9
and characteristics ETA trip system
ETA trip units include all functions offered by ET trip “Ammeter” measurements
unit. In addition, they also offer measurements, display ETA trip units measure the true (rms) value of currents.
and current maximeters. They provide continuous current measurements from 0.2 to 1.2 In and are accurate
to within 1.5 % (including the sensors).
A digital LCD screen continuously displays the most heavily loaded phase (Imax) or
CDB500003
displays the I1, I2, I3, IN, Ig, stored-current (maximeter) and setting values by
successively pressing the navigation button.
The optional external power supply makes it possible to display currents < 20 % In.
Below 0.1 In, measurements are not significant. Between 0.1 and 0.2 In, accuracy
changes linearly from 4 % to 1.5 %.
Protection
Protection thresholds and delays are set using the adjustment dials.
Overload protection
True rms long-time protection.
Short-time protection
protection devices
14 13
Earth-fault protection on ETA6G trip system
Residual earth fault protection.
long time
long time Selection of I2t type (ON or OFF) for delay.
Ir tr 8
alarm
alarm
.7
.8
.9 (s)
(s) 4 12 A ground fault in the protection conductors can provoke local temperature rise at
.6 .95 2 16 7 the site of the fault or in the conductors. The purpose of the ground-fault protection
.5 .98 1 20
.4
x In
1 .5
at 6 Ir
24 function is to eliminate this type of fault.
[Ir
Isd
short time
tsd Ii
instantaneous Type Description
4 5 (s) .4 .4 .3
(s) 8 10
3 6 Residual b The function determines the zero-phase sequence current, i.e. the
2.5 6 .3 .2 4 12
2 8 .2 .1 3 15 vectorial sum of the phase and neutral currents
1.5 10 on.1 2 0off 2 off
off b It detects faults downstream of the circuit breaker
on I t x In
x Ir
setting delay test
tg
test
Instantaneous protection
(s)
Ig
D E F (s) .4 .4 .3 The Instantaneous-protection function protects the distribution system against solid
C G .3 .2
B H .2 .1 short-circuits. Contrary to the short-time protection function, the tripping delay for
A I on.1 2 0off
instantaneous protection is not adjustable. The tripping order is sent to the circuit
on I t off
ground fault
ground fault
breaker as soon as current exceeds the set value, with a fixed time delay of
20 milliseconds.
Neutral protection
On three-pole circuit breakers, neutral protection is not possible.

On four-pole circuit breakers, neutral protection may be set using a three-position

switch: neutral unprotected (4P 3d), neutral protection at 0.5 Ir (4P 3d + N/2), neutral
protection at Ir (4P 4d).

A ZSI(2) terminal block may be used to interconnect a number of control units to
provide total discrimination for short-time and earth-fault protection, without a delay
8 Test connector.

before tripping.
11 Digital display.
Overload alarm
12 Three-phase bargraph and ammeter.
13 Navigation button to view menu contents.
14 Navigation button to change menu.

Fault indications
(1) The thermal memory continuously accounts for the amount b Overload (long-time protection Ir)
of heat in the cables , both before and after tripping , whatever b Short-circuit (short-time Isd or instantaneous li protection)
the value of the current(presence of an overload or not).The b Earth fault (Ig)
thermal memory optimises the long-time protection function of b Internal fault (Ap)

in the cables .The thermal memory assumes a cable cooling Battery power
time of approximately 20 minutes. The fault indicating LEDs are powered by an in-built battery. The fault indication
(2) Refer to page D-5 for more details on ZSI. LEDs remain on until the test/reset button is pressed.
Test
Note: ETA trip units come with a transparent leadseal cover as circuit-breaker operation. For ETA6G trip unit, the operation of earth-fault protection
standard. can be checked by pressing the test button located above the test connector.
A-10
Protection ETA2I
Long time ETA2I
DB101126
Time setting tr (s) 0.5 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 6 x Ir 0.7(1) 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 7.2 x Ir 0.7(2) 0.69 1.38 2.7 5.5 8.3 11 13.8 16.6
(1) 0 to -40 % - (2) 0 to -60 %
Instantaneous
Pick-up (A) Isd = Ir x … 1.5 2 2.5 3 4 5 6 8 10
Accuracy: ±10 %
Protection ETA5S/ETA6G
Long time ETA5S/ETA6G
DB101127
Time setting tr (s) 0.5 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 6 x Ir 0.7(1) 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 7.2 x Ir 0.7(2) 0.69 1.38 2.7 5.5 8.3 11 13.8 16.6
(1) 0 to -40 % - (2) 0 to -60 %
Short time
Pick-up (A) Isd = Ir x … 1.5 2 2.5 3 4 5 6 8 10
Accuracy: ±10 %
I2t On - 0.1 0.2 0.3 0.4
Instantaneous
Accuracy: ±10 %
Earth fault ETA6G
DB101128
Accuracy: ±10 % In y 400 A 0.3 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
400 A < In y 1000 A 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
In u 1250 A 500 640 720 800 880 960 1040 1120 1200
I2t On - 0.1 0.2 0.3 0.4
Ammeter ETA2I/ETA5S/ETA6G
Type of measurements Range Accuracy
Instantaneous currents I1, I2, I3, In 0.2 x In to 1.2 x In ± 1.5 %
Ig (ETA6G) 0.2 x In to In ± 10 %
Current maximeters of I1, I2, I3, In 0.2 x In to 1.2 x In ± 1.5 %
The test / reset button resets maximeters, clears the tripping indication and tests the battery.
A-11
and characteristics ETV trip system
ETV trip units include all the functions offered by ETA.

“Voltage meter” measurements
In addition, they measure voltage values.
In addition to the ammeter measurements of ETA
They also offer trip history & display tripping cause.
ETV trip units measure and display:
b Current demand
b Voltages: phase to phase, phase to neutral, average and unbalanced
CDB500004
The range of measurement is the same as current with ETA, depending of an

external power supply module.
Protection
Protection thresholds and delays are set using the adjustment dials.
Overload protection
True rms long-time protection.
Short-time protection
protection devices
Earth-fault protection on ETV6G trip system
15 14 Residual or source ground return earth fault protection.
Selection of I2t type (ON or OFF) for delay.
13 A ground fault in the protection conductors can provoke local temperature rise at
the site of the fault or in the conductors. The purpose of the ground-fault protection
function is to eliminate this type of fault.
long time
Ir
long time
.8 tr 8
alarm
alarm Type Description
.7 .9 (s)
(s) 4 12 b The function determines the zero-phase sequence current, i.e. the
Residual
.6 .95 2 16 7
.5 .98 1 20 vectorial sum of the phase and neutral currents
.4 1 .5 24
b It detects faults downstream of the circuit breaker
x In at 6 Ir
[Ir
Isd tsd Ii Instantaneous protection
3
4 5 (s) .4 .4 .3
(s) 8 10
6
2.5 6 .3 .2 4 12 The Instantaneous-protection function protects the distribution system against solid
2 8 .2 .1 3 15 short-circuits. Contrary to the short-time protection function, the tripping delay for
on.1
1.5 10 2 0off 2 off
off
x Ir
on I t x In instantaneous protection is not adjustable. The tripping order is sent to the circuit
test
setting
tg
delay
test breaker as soon as current exceeds the set value, with a fixed time delay of
(s)
Ig
D E F (s) .4 .4 .3 20 milliseconds.
C G .3 .2
B H .2 .1 Neutral protection
A I on.1 2 0off
on I t off
On three-pole circuit breakers, neutral protection is not possible.
ground fault
ground fault On four-pole circuit breakers, neutral protection may be set using a three-position
switch: neutral unprotected (4P 3d), neutral protection at 0.5 Ir (4P 3d + N/2), neutral
protection at Ir (4P 4d).


A ZSI(2) terminal block may be used to interconnect a number of control units to
provide total discrimination for short-time and earth-fault protection, without a delay
before tripping.

Overload alarm
8 Test connector.
Fault indications
11 Digital display.
b Overload (long-time protection Ir)
12 Three-phase bargraph and ammeter.

b Short-circuit (short-time Isd or instantaneous li protection)
13 Navigation button “quick View” (only with ETV).

b Earth fault (Ig)
14 Navigation button to view menu contents.

b Internal fault (Ap)
15 Navigation button to change menu.
Trip history
(1) The thermal memory continuously accounts for the amount The trip history displays the list of the last 10 trips. For each trip, the following
of heat in the cables , both before and after tripping , whatever indications are recorded and displayed:
the value of the current(presence of an overload or not).The b the tripping cause: Ir, Isd, Ii, Ig or Auto-protection (Ap) trips
thermal memory optimises the long-time protection function of Battery power
The fault indicating LEDs are powered by an in-built battery. The fault indication
in the cables .The thermal memory assumes a cable cooling
time of approximately 20 minutes. LEDs remain on until the test/reset button is pressed.
(2) Refer to page D-5 for more details on ZSI. Test
circuit-breaker operation. For ETV6G trip unit, the operation of earth-fault protection
Note: ETV trip units come with a transparent leadseal cover as can be checked by pressing the test button located above the test connector.
standard.
A-12
Protection ETV2I
Long time ETV2I
DB101126
Time setting tr (s) 0.5 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 6 x Ir 0.7(1) 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 7.2 x Ir 0.7(2) 0.69 1.38 2.7 5.5 8.3 11 13.8 16.6
(1) 0 to -40 % - (2) 0 to -60 %
Instantaneous
Pick-up (A) Isd = Ir x … 1.5 2 2.5 3 4 5 6 8 10
Accuracy: ±10 %
Protection ETV5S/ETV6G
Long time ETV5S/ETV6G
DB101127
Time setting tr (s) 0.5 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 6 x Ir 0.7(1) 1 2 4 8 12 16 20 24
Accuracy: 0 to -20 % 7.2 x Ir 0.7(2) 0.69 1.38 2.7 5.5 8.3 11 13.8 16.6
(1) 0 to -40 % - (2) 0 to -60 %
Short time
Pick-up (A) Isd = Ir x … 1.5 2 2.5 3 4 5 6 8 10
Accuracy: ±10 %
I2t On - 0.1 0.2 0.3 0.4
Instantaneous
Accuracy: ±10 %
Earth fault ETV6G
DB101128
Accuracy: ±10 % In y 400 A 0.3 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
400 A < In y 1000 A 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
In u 1250 A 500 640 720 800 880 960 1040 1120 1200
I2t On - 0.1 0.2 0.3 0.4
Energy ETV2I/5S/6G
Type of measurements Range Accuracy
Instantaneous currents I1, I2, I3, In 0.2 x In to 1.2 x In ± 1.5 %
Ig (ETV6G) 0.2 x In to In ± 10 %
Current maximeters of I1, I2, I3, In 0.2 x In to 1.2 x In ± 1.5 %
Demand currents of I1, I2, I3, Ig 0.2 x In to 1.2 x In ± 1.5 %
Voltages V12, V23, V31, V1N, V2N, V3N 100 to 690 V ± 0.5 %
The test / reset button resets maximeters, clears the tripping indication and tests the battery.
A-13
Functions ET range of trip system
and characteristics Accessories and test equipment
External sensors
DB101524
External sensor for earth-fault protection

The sensors, used with the 3P circuit breakers, are installed on the neutral
conductor for:
b Residual type earth-fault protection (with 6G trip units)
The rating of the sensor (CT) must be compatible with the rating of the
circuit breaker:
b MVS08 to MVS20: TC 400/2000
External sensor (CT).
b MVS25 to MVS40: TC 1000/4000
Voltage measurement inputs(1)
As standard, the control unit is supplied by internal voltage measurement inputs
placed downstream of the pole for voltages between 220 and 690 V AC.
External 24 V DC power-supply module
The external power-supply module makes it possible to use the display (ETA and
ETV trip systems) even if the circuit breaker is open or not supplied (for the exact
PB101026-32A
conditions of use, see the “electrical diagrams” part of this catalogue).

Characteristics
b Power supply:
v 110/130, 200/240, 380/415 V AC (+10 % -15 %)
v 24/30, 48/60, 100/125 V DC (+20 % -20 %)
b Output voltage: 24 V DC ±5 %, 1 A
b Ripple < 1 %
b Dielectric withstand : 3.5 kV rms between input/output, for 1 minute
External 24 V DC power supply module. b Overvoltage category: as per IEC 60947-1 cat. 4
Spare parts
Lead-seal covers
A lead-seal cover controls access to the adjustment dials.
PB100775-32
When the cover is closed:
b It is impossible to modify settings using the keypad unless the settings lockout pin
on the cover is removed

b The test connector remains accessible
b The test button for the earth-fault protection function remains accessible
Characteristics
b Transparent cover for all trip units
Spare battery
A battery supplies power to the LEDs identifying the tripping causes.The healthiness
of the battery to be checked periodically. A test button on the front of the control
unit is used to check the battery condition. The battery may be replaced on site
Lead-seal cover. when discharged.
Test equipment
Hand-held test kit
The hand-held mini test kit may be used to:
CDB500038
b Check operation of the control unit and the tripping and pole-opening system by
sending a signal simulating a short-circuit
b Power source: standard LR6-AA battery
Hand-held test kit.
(1) Refer to EasyPact MVS user manual on using 3 pole

circuit breakers in 4 wire system with ETV trip system for
voltage measurement.
A-14
Connections
Overview of solutions and accessories
Two types of connection are available: Rear connection

b Horizontal rear connection
Horizontal
b Vertical rear connection
The solutions presented are similar in principle for all
PB104354A40
EasyPact MVS fixed and drawout devices.
Vertical
PB104355A40
Mixed
PB104359A40
Simply turn a horizontal rear connector 90° to make it a vertical connector.
Interphase barriers EIP

CPB100010
These barriers are flexible insulated partitions used to reinforce isolation of

connection points in installations with busbars, whether insulated or not.
For EasyPact MVS devices, they are installed vertically between rear connection
terminals. They are not compatible with spreaders.
Safety shutters VO
Mounted on the chassis, the safety shutters automatically block access to the
disconnecting contact cluster when the device is in the disconnected or test positions
(degree of protection IP 20) When the device is removed from its chassis, no live
parts are accessible.
The shutter-locking system is made up of a moving block (optional device) that can
be padlocked (padlock not supplied). The block:
b Prevents connection of the device
b Locks the shutters in the closed position
PB104364A50
For EasyPact MVS08 to MVS40

A support at the bottom of the chassis is used to store the blocks when they are
not used:
b 2 blocks for MVS08 to MVS40
Note: EasyPact MVS circuit breakers can be connected indifferently with bare-copper, tinned-
copper and tinned-aluminium conductors, requiring no particular treatment.
A-15
Functions Accessories and auxiliaries
and characteristics
Type of accessory EasyPact MVS08 to MVS40

Fixed breaker Drawout breaker
Rear connection Rear connection
Interphase
DB101149
DB101149
barriers
Optional Optional
Safety shutters
DB101153
Standard
Safety shutters
E46460
locking blocks
Optional
Door interlock
E46452
Optional
Pushbutton
E46666
E46666
locking device
Optional Optional
OFF position locking
CDB500039
CDB500039
Optional Optional
“Disconnected”
E46451
position locking
Optional
ON/OFF indication
E46689
E46689
contacts(OF)
Standard Standard
Additional ON/OFF
E46689
E46689
indication contacts(OF)
Optional Optional
“Fault trip” indication
CDB500040
CDB500040
contact(SDE)
Standard Standard
A-16
Type of accessory EasyPact MVS08 to MVS40
Fixed breaker Drawout breaker
Rear connection Rear connection
“Connected, disconnected,
E46661
test position”
indication
contact(CE,CD,CT)
Optional
“Ready to close”
E46438
E46438
contact(PF)
Optional Optional
Escutcheon(CDP)
CDB500061
CDB500061
Standard Standard
Mechanical operation
DB125617
DB125617
counter(CDM)
Optional Optional
Escutcheon
E46670
E46670
blanking plate
Optional Optional
Auxiliary
E46458
terminal shield(CB)
Optional
Transparent
E46669
cover (IP54)
Optional
A-17
Functions Locking
and characteristics On the device
CDB500006
1 Reset button for mechanical trip indication.
2 OFF pushbutton.
3 OFF position lock.
4 Door interlock.
5 ON pushbutton. ET6G
ET6G
Trip Syste
System
Trip
m
6 Spring charge indication.

7 Pushbutton locking.
N
MVS08
8 Contact position indication.

alarm
alarm
-2 50/60H
time tr 60947
long
long
time
(s) 4
8 12
16
IEC
.8 .9.95(s)
Ir 2 20
.7
1 24 ous
us
.6 .98 .5 at 6IrIr instantane
.5 instantaneo
1
.4 x In Ii 8 1012
6
shorttime tsd .4 .4 .3
time
short (s)
(s) .2 4 15
.1 3 off
Isd
3
4 5
6
.3 2
off
9 Operation counter.
.2 0off x In test
2.5 8 .1 2
I t
test
2 10 on
on
1.5 Ir delay
x
setting tg . 4 .3 2
(s)
(s) .4 .
Ig D
E F .3 .1
G
C H
. 2 off
0off
B
on.1 2
I t
I on
A fault
ground
fault
ground
Pushbutton locking VBP

PB100811-32
The transparent cover blocks access to the pushbuttons used to open and close
the device.
It is possible to independently lock the opening button and the closing button.
The locking device is often combined with a remote operating mechanism.
The pushbuttons may be locked using either:
b Three padlocks (not supplied)
b Lead seal
Access to pushbuttons protected by transparent cover. b Two screws
Device locking in the OFF position by keylocks VSPO

The circuit breaker is locked in the OFF position by physically maintaining the
PB100810-32
opening pushbutton pressed down:

b Using keylocks (one or two keylocks, supplied)
Keys may be removed only when locking is effective (Profalux or Ronis type locks).
The keylocks are available in any of the following configurations:
b One keylock
b One keylock mounted on the device + one identical keylock supplied separately
for interlocking with another device
A locking kit (without locks) is available for installation of one or two keylocks (Ronis,
Profalux).
Pushbutton locking using a padlock.
CDB500036
CPB100007
Profaulx Ronis
Door interlock catch VPEC

Mounted on the right or left-hand side of the chassis, this device inhibits opening of
the cubicle door when the circuit breaker is in “connected” or “test” position. It the
OFF position locking using a keylock. breaker is put in the “connected” position with the door open, the door may be closed
without having to disconnect the circuit breaker.
Automatic spring discharge before breaker removal DAE
CPB100008
This option discharges the springs before the breaker is removed from the chassis.
Door interlock.
A-18
On the chassis
“Connected”, “disconnected” and “test” position racking

CDB500007
interlock
The “connected”, “disconnected” and “test” positions are shown by an indicator and
are mechanically indexed. The exact position is obtained when the racking handle
blocks. A release button is used to free it.
“Disconnected” position locking by padlocks or keylocks
VSPD
Mounted on the chassis and accessible with the door closed, these devices lock the
circuit breaker in the “disconnected” position in two manners:
4 b Using padlocks (standard), up to three padlocks (not supplied)
8 b Using keylocks (optional), one or two different keylocks are available
1 Profalux and Ronis keylocks are available in different options:
7 5 b One keylock
6 b Two identical key locks - one keylock mounted on the device + one identical
2
3 keylock supplied separately for interlocking with another device
A locking kit (without locks) is available for installation of one or two keylocks
(Ronis, Profalux).
1 Door interlock.
2 Keylock locking. Padlock
3 Padlock locking.
4 Position indicator. Circuit breaker in “disconnected” Pull out the tab.

5 Chassis front plate (accessible with cubicle door closed).
6 Racking-handle entry.
position.
7 Release button.
8 Racking-handle storage.
CPB100006
Insert the shackle (max. diameter The crank connot be inserted.

5 to 8 mm) of the padlock(s).
“Disconnected” position locking by padlock.

Keylock
Circuit breaker in “disconnected” Turn the key(s).
position.
CPB100017
“Disconnected” position locking by keylock. Remove the key(s) The crank cannot be inserted.
A-19
Functions Indication contacts
and characteristics
Indication contacts are available: ON/OFF indication contacts OF

b in the standard version for relay applications Indication contacts indicate the ON or OFF position of the circuit breaker:
b Rotary type changeover contacts directly driven by the mechanism for EasyPact
MVS. These contacts trip when the minimum isolation distance between the main
circuit-breaker contacts is reached
OF MVS
Supplied as standard 1 (4 C/O)
PB100807-20
Optional contact 1 (4 C/O)

Breaking capacity (A) Standard Minimum load: 100 mA/24 V
p.f.: 0.3 V AC 240/380 10/6 (1)
AC12/DC12 480 10/6 (1)
690 6
V DC 24/48 10/6 (1)
125 10/6 (1)
250 3
(1) Standard contacts: 10 A; optional contacts: 6 A.
ON/OFF indication contacts “Fault-trip” indication contacts SDE

(OF) (rotary type). Circuit-breaker tripping due to a fault is signalled by:
b A red mechanical fault indicator (reset)
b One changeover contact SDE
Following tripping, the mechanical indicator must be reset before the circuit breaker
PB100818-16
may be closed. One SDE is supplied as standard.
SDE MVS
Supplied as standard 1
p.f.: 0.3 V AC 240/380 5
AC12/DC12 480 5
690 3
V DC 24/48 3
125 0.3
250 0.15
“Connected”, “disconnected” and “test” position carriage

switches CE, CD & CT
Three series of optional auxiliary contacts are available for the chassis:
b Changeover contacts to indicate the “connected” position CE
“Fault-trip” indication contact (SDE). b Changeover contacts to indicate the “disconnected” position CD. This position
is indicated when the required clearance for isolation of the power and auxiliary
circuits is reached
b Changeover contacts to indicate the “test” position CT. In this position, the power
PB100817-32
circuits are disconnected and the auxiliary circuits are connected

Additional actuators
A set of additional actuators may be installed on the chassis to change the functions
of the carriage switches.
MVS
Contacts CE/CD/CT
Maximum number Standard 3 3 3
p.f.: 0.3 V AC 240 8
AC12/DC12 380 8
480 8
CE, CD and CT “connected/ 690 6
disconnected/test” position V DC 24/48 2.5
carriage switches. 125 0.8
250 0.3
A-20
Remote operation
Remote ON / OFF
A point-to-point solution for remote operation of The remote ON / OFF function is used to remotely open and close the circuit breaker.
EasyPact MVS It is made up of:
b An electric motor MCH equipped with a “springs charged” limit switch contact CH
b Two voltage releases:
v A closing release XF
PB104349A68
v An opening release MX
Optionally, other function may be added:
b A “ready to close” contact PF
A remote-operation function is generally combined with:
b Device ON / OFF indication OF
b “Fault-trip” indication SDE
Wiring diagram of a point-to-point remote ON / OFF function

DB111783
Note: An opening order always takes priority over a

closing order.
If opening and closing orders occur simultaneously, the
mechanism discharges without any movement of the main
contacts. The circuit breaker remains in the open position
(OFF).
In the event of maintained opening and closing orders, the
standard mechanism provides an anti-pumping function by
blocking the main contacts in open position.
Anti-pumping function. After fault tripping or intentional
opening using the manual or electrical controls, the closing
order must first be discontinued, then reactivated to close the
circuit breaker.
A-21
Functions Remote operation
and characteristics Remote ON / OFF
Electric motor MCH

PB100808-32
The electric motor automatically charges and recharges the spring mechanism when
the circuit breaker is closed. Instantaneous reclosing of the breaker is thus possible
following opening. The spring-mechanism charging handle is used only as a backup
if auxiliary power is absent.
The electric motor MCH is equipped as standard with a limit switch contact CH that
signals the “charged” position of the mechanism (springs charged).
Characteristics
Power supply V AC 50/60 Hz 100/130 - 200/240 - 380/415
V DC 24/30 - 48/60 - 100/125 - 200/250
Operating threshold 0.85 to 1.1 Un
Consumption (VA or W) 180
Motor overcurrent 2 to 3 In for 0.1 s
Charging time Maximum 4 s
Operating frequency Maximum 3 cycles per minute
CH contact 10 A at 240 V
Voltage releases XF and MX

Their supply can be maintained or automatically disconnected.
Closing release XF
Electric motor MCH for The XF release remotely closes the circuit breaker if the spring mechanism
EasyPact MVS. is charged.
Opening release MX
The MX release instantaneously opens the circuit breaker when energised. It locks
the circuit breaker in OFF position if the order is maintained.
DB117037
Characteristics XF MX
Power supply V AC 50/60 Hz 24 - 48 - 100/130 - 200/250 - 277 - 380/480
V DC 12 - 24/30 - 48/60 - 100/130 - 200/250
Operating threshold 0.85 to 1.1 Un 0.7 to 1.1 Un
Consumption (VA or W) Hold: 4.5 Hold: 4.5
Pick-up: 200 (200 ms) Pick-up: 200 (200 ms)
Circuit-breaker response time at Un 70 ms ±10 50 ms ±10
“Ready to close” contact PF

PB100809-16
The “ready to close” position of the circuit breaker is indicated by a mechanical

indicator and a PF changeover contact. This signal indicates that all the following
are valid:
b The circuit breaker is in the OFF position
b The spring mechanism is charged
b A maintained opening order is not present:
v MX energised
v Fault trip
v Remote tripping MN
v Device not completely racked in
MX voltage releases. XF voltage release.
v Device locked in OFF position
v Device interlocked with a second device
Characteristics
PB100818-16
Maximum number 1
p.f.: 0.3 V AC 240/380 5
AC12/DC12 480 5
690 3
V DC 24/48 3
125 0.3
250 0.15
“Ready to close” contacts PF.
A-22
Remote tripping
Instantaneous voltage releases MN

DB100809-16
The MN release instantaneously opens the circuit breaker when its supply voltage
drops to a value between 35 % and 70 % of its rated voltage. If there is no supply on
the release, it is impossible to close the circuit breaker, either manually or electrically.
Any attempt to close the circuit breaker has no effect on the main contacts. Circuit
breaker closing is enabled again when the supply voltage of the release returns to
85% of its rated value.
Characteristics
Power supply V AC 50/60 Hz 24 - 48 - 100/130 - 200/250 - 380/480
V DC 24/30 - 48/60 - 100/130 - 200/250
MN voltage release. Operating threshold Opening 0.35 to 0.7 Un
Closing 0.85 Un
Consumption (VA or W) Pick-up: 200 (200 ms) Hold: 4.5
MN consumption Pick-up: 200 (200 ms) Hold: 4.5
with delay unit (VA or W)
Circuit-breaker response time at Un 90 ms ±5
MN delay units
To eliminate circuit-breaker nuisance tripping during short voltage dips, operation of
056422N
the MN release can be delayed. This function is achieved by adding an external

delay unit in the MN voltage-release circuit. Two versions are available, adjustable
and non-adjustable.
Characteristics
Power supply Non-adjustable 100/130 - 200/250
V AC 50-60 Hz /DC Adjustable 48/60 - 100/130 - 200/250 - 380/480
Operating threshold Opening 0.35 to 0.7 Un
Closing 0.85 Un
MN delay unit. Delay unit consumption Pick-up: 200 (200 ms) Hold: 4.5
Circuit-breaker response time at Un Non-adjustable 0.25 s
Adjustable 0.5 s - 0.9 s - 1.5 s - 3 s
A-23
Functions Source-changeover systems
and characteristics Mechanical interlocking
Interlocking of two EasyPact MVS or up to three EasyPact MVS

CPB100009
devices using cables

For cable interlocking, the circuit breakers may be mounted one above the other or
side-by-side. The interlocked devices may be fixed or drawout, three-pole or four-
pole, and have different ratings.
Interlocking between two devices
This function requires:
b An adaptation fixture on the right side of each device
b A set of cables with no-slip adjustments
b The use of a mechanical operation counter CDM is compulsory
The maximum distance between the fixing planes (vertical or horizontal) is 2000 mm.
Interlocking between three devices
This function requires:
b A specific adaptation fixture for each type of interlocking, installed on the right side
Interlocking of two EasyPact circuit breakers using cable.
of each device
b Two or three sets of cables with no-slip adjustments
b The use of a mechanical operation counter CDM is compulsory
The maximum distance between the fixing planes (vertical or horizontal) is 1000 mm.
Installation
The adaptation fixtures, sets of cables and circuit breakers or switch-disconnectors
are supplied separately, ready for assembly by the customer.
Installation conditions for cable interlocking systems:

b Cable length: 2.5 m
b Radius of curvature: 100 mm
b Maximum number of curves: 3
Possible combinations of “Normal” and “Replacement” source circuit breakers

“Normal N” “Replacement” R
MVS08 to MVS40 MVS08 to MVS40
Ratings 800...4000A b
Possible combinations of three device

MVS08 to MVS40 MVS08 to MVS40
Ratings 800...4000A b
All combinations of two or three EasyPact MVS devices are possible, whatever the
rating of the devices.
A-24
Accessories
Auxiliary terminal shield CB

PB104740
Optional equipment mounted on the chassis, the shield prevents access to the
terminal block of the electrical auxiliaries.
Operation counter CDM

PB104382A32
The operation counter sums the number of operating cycles and is visible on the
front panel. It is compatible with manual and electrical control functions.
This option is compulsory for all the source-changeover systems.
Escutcheon CDP
DB101173
Standard equipment mounted on the door of the cubicle, the escutcheon increases
the degree of protection to IP 40 (circuit breaker installed free standing: IP30) .
It is available in fixed and drawout versions.
Blanking plate for escutcheon OP

Used with the escutcheon, this option closes off the door cut-out of a cubicle not yet
equipped with a device. It may be used with the escutcheon for both fixed and
drawout devices.
Escutcheon CDP with blanking plate.
Transparent cover for escutcheon CP

PB100776-42
Optional equipment mounted on the escutcheon, the cover is hinged and secured by
a screw. It increases the degree of protection to IP54, IK10. It adapts to drawout
devices.
Transparent cover CP for escutcheon.
A-25
Installation
recommendations
EasyPact MVS Installation recommendations
Functions and characteristics A-1
Operating conditions B-2
Installation in switchboard B-3

Door interlock catch B-5
Control wiring B-6
Power connection B-7
Recommended busbars drilling B-9
Busbar sizing B-10
Temperature derating
Power dissipation B-11
B-1
Installation Operating conditions
recommendations
EasyPact MVS circuit breakers have been tested for

operation in industrial atmospheres. It is recommended
that the equipment be cooled or heated to the proper
operating temperature and kept free of excessive
vibration and dust.
Ambient temperature
CDB500008
EasyPact MVS devices can operate under the following temperature conditions:
b The electrical and mechanical characteristics are stipulated for an ambient
temperature of -5°C to +60°C
b Circuit-breaker closing is guaranteed down to -35°C
Storage conditions are as follows:
ET6G
ET6G
Trip
Trip
System
System
b -40 to +85°C for a Easypact MVS device without its control unit
long
long
time tr
time
(s) 4
(s)
8 12
16
alarm
alarm
MVS08
IEC
N
60947-2
50/60H
b -25°C to +85°C for the control unit
Ir .8 .9.95 2 20
1 24
.6.7 .98 .5 at 6IrIr instantaneous
.5 instantaneous
1
.4 x In Ii 8 1012
6
time
short (s)
(s) .2 4 15
3 off
Isd
3
4 5 .3 .1 2
off
6
8
. 2 0off x In test
2.5 .1 2
I t
test
2 10 on
on
1.5 Ir delay
x
setting tg .4 .3 2
(s)
(s) .4 .
Ig
E F .3 .1
G
CD H
.2 off
0off
B
on.1 I2t
I on
A fault
groundfault
ground
(m)
2000
Altitude
At altitudes higher than 2000 metres, the modifications in the ambient air (electrical
CDB500011
resistance, cooling capacity) lower the following characteristics as follows:
Altitude (m) 2000 3000

Impulse withstand voltage uimp (kV) 12 11
Rated insulation voltage (Ui) 1000 900
Maximum rated operationnal 690 590
voltage 50/60 Hz Ue (V) 1000 890
Rated current 40°C 1 x In 0.99 x In
Trip System
System
ET6G Trip
ET6G
N
MVS08
Intermediate values may be obtained by interpolation.

alarm
alarm 50/60H
time tr 60947-2
long
long
time
(s) 4
8 12
16
IEC
.8 .9.95(s)
Ir 2 20
1 24
.5 instantaneous
1
.4 x In Ii 8 1012
6
time
short (s)
(s) .2 4 15
3 off
Isd
3
4 5 .3 .1 2
off
6
8
. 2 0off x In test
2.5 .1 2
I t
test
2 10 on
on
1.5 Ir delay
x
setting tg . 4 .3 2
(s)
(s) .4 .
Ig
E F .3 .1
G
CD H
.2 off
0off
B
on.1 I2t
I on
A fault
groundfault
ground
Electromagnetic disturbances
CDB500012
EasyPact MVS devices are protected against:

b Overvoltages caused by devices that generate electromagnetic disturbances
b Overvoltages caused by atmospheric disturbances or by a distribution-system
outage (e.g. failure of a lighting system)
b Devices emitting radio waves (radios, walkie-talkies, radar, etc.)
b Electrostatic discharges produced by users
EasyPact MVS devices have successfully passed the electromagnetic-compatibility
tests (EMC) defined by the following international standards:
b IEC 60947-2, appendix F
The above tests guarantee that:
Trip System
System
ET6G Trip
ET6G
N
MVS08
Ir
.6.7
.5
Isd
2.5
Ig
2
3
long
long
.8 .9
.4 x In
4 5
1.5 Ir
CD
x
10
setting
E F
6
8
1
G
time tr
time
.95
.98
H
(s) 4
(s)
tg
2
1
.3
on
on
(s)
2
.1
(s) .4
.3
.2
8 12
on.1 I2t
16
.5 at 6IrIr
short
time
(s)
(s)
2
I t
delay
.4 .3.2
.1
off
0off
20
24
.2
.1
0off
alarm
alarm
instantaneous
Ii
4
3
instantaneous
2
8 1012
15
off
off
x In test
test
IEC
60947-2
50/60H
b No nuisance tripping occurs

b Tripping times are respected
B I on
A fault
groundfault
ground
B-2
Installation in switchboard
Possible positions
CDB500013
CDB500014
CDB500015
Trip System
System
ET6G Trip
ET6G
N
MVS08
alarm
alarm 50/60H
time tr 60947-2
long
long
time 8 12 IEC
(s) 4
(s) 16
Ir .8 .9 2 20
.95
1 24
.5 instantaneous
1
.4 x In Ii 8 1012
6
time
short (s)
(s) .2 4 15
3 off
Isd
3
4 5 .3 .1 2
off
6
8
. 2 0off x In test
2.5 .1 2
I t
test
2 10 on
on
1.5 Ir delay
x
setting tg
(s) .4 .3.2
(s) .4
Ig
E F .3 .1
G
CD H
.2 off
0off
B
on.1 I2t
I on
A fault
groundfault
ground
Power supply
EasyPact MVS devices can be supplied either from the top or from the bottom
without reduction in performance, in order to facilitate connection when installed
in a switchboard.
CDB500016
Trip System
System
ET6G Trip
ET6G
N
MVS08
alarm
alarm 50/60H
60947-2
long
long
time tr
time 8 12 IEC
(s) 4
(s) 16
Ir .8 .9 2 20
.95
1 24
.5 instantaneous
1
.4 x In Ii 8 1012
6
time
short (s)
(s) .2 4 15
3 off
Isd
3
4 5 .3 .1 2
off
6
8
. 2 0off x In test
2.5 .1 2
I t
test
2 10 on
on
1.5 Ir delay
x
setting tg
(s) .4 .3.2
(s) .4
Ig
E F .3 .1
G
CD H
.2 off
0off
B
on.1 I2t
I on
A fault
groundfault
ground
Mounting the circuit-breaker

It is important to distribute the weight of the device uniformily over a rigid mounting
surface such as rails or a base plate.
This mounting plane should be perfectly flat (tolerance on support flatness: 2 mm).
This eliminates any risk of deformation which could interfere with correct operation
of the circuit breaker.
EasyPact devices can also be mounted on a vertical plane using the
special brackets.
CDB500017
CDB500018
Trip System
System
System
ET6G Trip Trip
System
Trip
ET6G ET6G
ET6G
N
MVS08 N
MVS08
alarm
alarm 50/60H 50/60H
alarm
alarm
time tr 60947-2 60947-2
long
long
time 8 12 IEC time tr 8 12 IEC
(s) 4
(s) 16 long
long
time
.8 .9.95 (s) 4 16
Ir
.7
2 20
Ir .8 .9.95 (s)2
1 s .7 20
24 s
.6 .98 .5 at 6IrIr instantaneou 1 24
instantaneous .6 .98 .5 at 6IrIr instantaneou
.5 1 instantaneous
.4 x In Ii 8 1012 .5 1
6 .4 x In Ii 8 1012
time 6
time
short (s) .2 4 15
(s)
.1 3 off short (s) .2 4 15
Isd 4 5 .3 off (s)
.1 3 off
3 6
. 2
2
x In test
Isd
3
4 5
6
.3 2
off
0off
2.5 8 .1 2
I t
test .2 2 0off x In test
2 10 on
on 2.5 8 .1 I t test
delay 2 10 on
on
1.5 Ir delay
x 1.5 Ir
setting tg . 4 .3 2 x
(s) .4 . setting tg . 4 .3 2
(s) (s)
(s) .4 .
Ig D
E F .3 .1
G
. 2 off Ig D
E F .3 .1
0off G
C H
on.1 2 .2 off
0off
I t C H
B I on
B
on.1 2
I t
A fault
I on
A fault
ground
fault
ground ground
fault
ground
Mounting on rails.
B-3
Installation Installation in switchboard
recommendations
Partitions
DB101434
Sufficient openings must be provided in partitions to
ensure good air circulation around the circuit breaker;
Any partition between upstream and downstream
connections of the device must be made of
nonmagnetic material.
For high currents, of 2500 A and upwards, the metal
supports or barriers in the immediate vicinity of a
conductor must be made of non-magnetic material A.
Metal barriers through which a conductor passes must
not form a magnetic loop.
DB101435 A : Non magnetic material.
Busbars
DB117045
DB101436
The mechanical connection must be exclude the
possibility of formation of a magnetic loop around
a conductor.
Interphase barrier
CDB500041
DB101439
If the insulation distance between phases is not

sufficient (y 14 mm), it is advised to install phase
barriers (taking into account the safety clearances).
453
B-4
Door interlock catch
Door interlock VPEC
DB117044
CDB500034
Mounted on the right or left-hand side of the chassis,
this device inhibits opening of the cubicle door when
the circuit breaker is in “connected” or “test” position.
It the breaker is put in the “connected” position with the
door open, the door may be closed without having to
disconnect the circuit breaker.
Dimensions (mm)
Type (1) (2)
MVS08-40 (3P) 215 215
MVS08-40 (4P) 330 215
Catch not supplied
Breaker in “connected” Breaker in “disconnected”

or “test” position position
Door cannot be opened Door can be opened
DB103819
DB102194
83
103
Note: Dimensions are in mm.
Note: The door interlock can either be mounted on the right

side or the left side of the breaker.
: Datum.
B-5
Installation Control wiring
recommendations
Wiring of voltage releases

During pick-up, the power consumed is approximately 150 to 200 VA. For low control
voltages (12, 24, 48 V), maximum cable lengths are imposed by the voltage and the
cross-sectional area of cables.
Recommended maximum cable lengths (meter).
12 V 24 V 48 V
2,5 mm2 1,5 mm2 2,5 mm2 1,5 mm2 2,5 mm2 1,5 mm2
MN U source 100 % – – 58 35 280 165
U source 85 % – – 16 10 75 45
MX-XF U source 100 % 21 12 115 70 550 330
U source 85 % 10 6 75 44 350 210
Note: The indicated length is that of each of the two wires.
24 V DC power-supply module
External 24 V DC power-supply module (F1-, F2+)
b Do not connect the positive terminal (F2+) to earth

b The negative terminal (F1-) can be connected to earth
b A number of trip units can be connected to the same 24 V DC power supply (the
consumption of a trip unit is approximately 100 mA)
b Do not connect any devices other than a trip unit
b The maximum length for each conductor is ten metres. For greater distances, it is
advised to twist the supply wires together
b The 24 V DC supply wires must cross the power cables perpendicularly. If this is
difficult, it is advised to twist the supply wires together
b The technical characteristics of the external 24 V DC power-supply module are
indicated on page A-14.
Note: Wiring of ZSI: it is recommended to use twisted shielded cable. The shield must be
connected to earth at both ends.
B-6
Power connection
Cables connections
DB101448
DB101449
If cables are used for the power connections, make
sure that they do not apply excessive mechanical
forces to the circuit breaker terminals.
For this, make the connections as follows:
b Extend the circuit breaker terminals using short
bars designed and installed according to the
recommendations for bar-type power connections:
v For a single cable, use solution B opposite
v For multiple cables, use solution C opposite
b In all cases, follow the general rules for connections
to busbars:
v Position the cable lugs before inserting the bolts
v The cables should firmly secured to the framework E
DB101450
Busbars connections
DB101451
DB101452
The busbars should be suitably adjusted to ensure that

the connection points are positioned on the terminals
before the bolts are inserted B
The connections are held by the support which is
solidly fixed to the framework of the switchboard, such
that the circuit breaker terminals do not have to support
its weight C. (This support should be placed close to
the terminals).
DB101453
Electrodynamic stresses
The first busbar support or spacer shall be situated within a maximum distance from
the connection point of the breaker (see table below). This distance must be
respected so that the connection can withstand the electrodynamic stresses
between phases in the event of a short circuit.
Maximum distance A between busbar to circuit breaker connection and the first busbar
support or spacer with respect to the value of the prospective short-circuit current.
Isc (kA) 30 50 65
Distance A (mm) 350 300 250
B-7
Installation Power connection
recommendations
Clamping
DB101454
Correct clamping of busbars depends amongst other things, on the tightening

torques used for the nuts and bolts. Over-tightening may have the same
consequences as under-tightening.
For connecting busbars (Cu ETP-NFA51-100) to the circuit breaker, the tightening
torques to be used are shown in the table below.
These values are for use with copper busbars and steel nuts and bolts, class 8.8. The
same torques can be used with AGS-T52 quality aluminium bars (French standard
NFA 02-104 or American National Standard H-35-1).
Examples
DB101455
DB101456
DB101457
1 Terminal screw factory-tightened to 16 Nm.
2 Breaker terminal.
3 Busbar. Tightening torques
4 Bolt. Ø (mm) Ø (mm) Tightening torques (Nm) Tightening torques (Nm)
5 Washer. Nominal Drilling with grower or flat washers with contact or corrugatec
6 Nut. washers
10 11 37.5 50
Busbar drilling
Examples
DB101458
DB101459
DB101460
Isolation distance
DB101461
Dimensions (mm)
Ui X min
600 V 8 mm
1000 V 14 mm
Busbar bending
When bending busbars maintain the radius indicated below(a smaller radius would
cause cracks).
DB101462
Dimensions (mm)
e Radius of curvature r
Min Recommended
5 5 7.5
10 15 18 to 20
B-8
Recommended busbars drilling
EasyPact MVS08 to MVS40
Horizontal rear connection MVS08 to MVS32 MVS40

DB101463
DB101464
DB101465
CDB500042
DB101474
CDB500054
CDB500055
Vertical rear connection MVS08 to MVS32 MVS40

DB101476
CDB500043
DB101477
CDB500056
B-9
B-10
Power dissipation
The table below indicates the maximum current rating,
for each connection type, as a function of Ti around the
circuit breaker and the busbars.
For Ti greater than 60°C, consult us.
Ti: temperature around the circuit breaker and
its connection.
Version Drawout Fixed

Connection Rear horizontal Rear vertical Rear horizontal Rear vertical
Temp. Ti 40 °C 45 °C 50 °C 55 °C 60 °C 40 °C 45 °C 50 °C 55 °C 60 °C 40 °C 45 °C 50 °C 55 °C 60 °C 40 °C 45 °C 50 °C 55 °C 60 °C
MVS (50kA)
MVS08N 800 800 800 800
MVS10N 1000 1000 1000 1000
MVS12N 1250 1250 1250 1250
MVS16N 1600 1600 1600 1600
MVS20N 2000 1900 1800 2000 1900 2000 1920 2000
MVS25N 2500 2450 2500 2500 2500
MVS32N 3200 3100 3000 2900 3200 3200 3200
MVS40N 4000 3900 3750 3650 4000 3900 4000 3900 3800 4000
MVS (65kA)
MVS08H 800 800 800 800
MVS10H 1000 1000 1000 1000
MVS12H 1250 1250 1250 1250
MVS16H 1600 1600 1600 1600
MVS20H 2000 1900 1800 2000 1900 2000 1920 2000
MVS25H 2500 2450 2400 2300 2200 2500 2450 2400 2300 2500 2500
MVS32H 3200 3100 3000 2900 3200 3200 3200
MVS40H 4000 3900 3750 3650 4000 3900 4000 3900 3800 4000
Power dissipation
Total power dissipation is the value measured at IN,
50/60 Hz, for a 3 pole or 4 pole breaker (values above
the power P = 3RI2). The resistance between input /
output is the value measured per pole (cold state).
Type Draw-out Fixed

50kA Power loss Input/output resistance Power loss Input/output resistance
(W) (µohm) (W) (µohm)
MVS08N 120 36 60 19
MVS10N 180 36 100 19
MVS12N 280 36 140 19
MVS16N 460 36 200 19
MVS20N 470 30 250 13
MVS25N 600 19 260 13
MVS32N 670 13 420 8
MVS40N 900 11 650 8
65kA
MVS08H 100 30 42 13
MVS10H 150 30 70 13
MVS12H 230 30 100 13
MVS16H 390 30 170 13
MVS20H 470 30 250 13
MVS25H 600 19 260 8
MVS32H 670 13 420 8
MVS40H 900 11 650 8
B-11
Dimensions
and connection
EasyPact MVS Dimensions and connection
MVS08 to MVS32 circuit breakers C-2
Fixed 3/4-poles device C-2
Drawout 3/4-poles device C-4
MVS40 circuit breakers C-6
Fixed 3/4-poles device C-6
Drawout 3/4-poles device C-8
Accessories C-10
External modules C-11
C-1
Dimensions MVS08 to MVS32 circuit breakers
and connection Fixed 3/4-poles device
Dimensions
DB101267
CDB500019
Mounting on base plate or rails Mounting detail

DB101269
DB101270
Safety clearances
DB101271
CDB500020
DB101273
Insulated Metal Energised

parts parts parts
A 0 0 100 (1) Without escutcheon.
B 0 0 60 (2) With escutcheon.
Note: X and Y are the symmetry planes for a 3-pole device.
: Datum. A(*) An overhead clearance of 50 mm is required to remove the arc chutes.
An overhead clearance of 20 mm is required to remove the terminal block.
C-2
Connections
Horizontal rear connection Detail
DB101274
DB101276
DB101277
DB101278
Vertical rear connection Detail
DB101280
DB101287
DB101279
DB101282
View A detail.
Note: Recommended connection screws: M10 class 8.8.

Tightening torque: 50 Nm with contact washer.
C-3
Dimensions MVS08 to MVS32 circuit breakers
and connection Drawout 3/4-poles device
Dimensions
DB101289
CDB500021
(*) Disconnected position.

DB101291
DB101292
Safety clearances Door cutout

DB101294
DB101293
CDB500022
DB101295

parts parts parts
A 0 0 0
B 0 0 60
(1) Without escutcheon.
: Datum. (2) With escutcheon.
C-4
Connections
Horizontal rear connection Detail
CDB500044
DB101297
DB101298
DB101278
Vertical rear connection Detail
CDB500045
DB101301
DB101307
DB101282
View A detail.

C-5
Dimensions MVS40 circuit breakers
and connection Fixed 3/4-poles device
Dimensions
CDB500019
DB101267

DB101269
DB101270

CDB500020
DB101271
DB101273

parts parts parts
A 0 0 100 (1) Without escutcheon.
B 0 0 60 (2) With escutcheon.
: Datum. A(*) An overhead clearance of 110 mm is required to remove the arc chutes.
An overhead clearance of 20 mm is required to remove the terminal block.
C-6
Connections
Horizontal rear connection
DB101309
DB101276
Detail
CDB500049
DB101311
CDB500049
15
DB101315
400(3P)
Vertical rear connection

DB101312
DB101313
Detail
DB101287
DB101314

C-7
Dimensions MVS40 circuit breakers
and connection Drawout 3/4-poles device
Dimensions
DB101289
CDB500021
(*) Disconnected position.

DB101291
DB101292

DB101294
DB101293
DB101295
CDB500022

parts parts parts
A 0 0 60
B 0 0 60 (1) Without escutcheon.
(2) With escutcheon.
: Datum. Note: X and Y are the symmetry planes for a 3-pole device.
The safety clearances take into account the space required to remove the arc chutes.
C-8
Connections
Horizontal rear connection
CDB500046
DB101297
Detail
CDB500050
CDB500050
DB101311
DB101315
15
400(3P)
Vertical rear connection

CDB500047
DB101319
DB101314
View A detail.
Detail
DB101307

C-9
Dimensions Accessories
and connection
Rear panel cutout (drawout devices)

MVS08 to MVS40
Rear view
DB125695
DB101360
Escutcheon
EasyPact MVS
Fixed device Drawout device
DB101365
DB101366
: Datum.
C-10
External modules
Connection of auxilary wiring to terminal block
DB101367
DB101368
One conductor only per connection point.
External power supply module (AD)

DB102077
DB102076
Delay unit for MN release

DB101375
DB117025
C-11
Dimensions External modules
and connection
External sensor for external neutral

Dimensions
400/2000 A (MVS08 to MVS20) 1000/4000 A (MVS25 to MVS40)
DB117024
DB117023
High: 162 mm.

High: 162 mm.
Installation
400/2000 A (MVS08 to MVS20) 1000/4000 A (MVS25 to MVS40)
DB101386
DB101387
C-12
C-13
Electrical diagrams
EasyPact MVS
Electrical diagrams
EasyPact MVS08 to 40 D-2
Fixed and drawout devices D-2
EasyPact MVS D-4
Earth-fault protection/Neutral protection D-4
Zone selective interlocking D-5
24 V DC external power supply AD module D-6
D-1
Electrical diagrams Masterpact MVS08 to MVS40
Fixed and drawout devices
The diagram is shown with circuits

de-energised, all devices open, connected
and charged and relays in normal position.
Power ET/ETA/ETV trip system Remote operation
to-close
Ready-
Charged
Fault
Close
Stop
VN
V1
V2
V3
Open
ET trip system ETA/ETV trip system
U
E89955
NCT
Note: V1...VN Voltage connections are available in ETV trip system.
E60065A
E46136A
E46137A
E60066A
E60067A
E89956
ET trip system ETA/ETV trip system Remote operation

UC1 UC2 UC1 UC2 UC3 SDE MN MX XF PF MCH
Z5 Z5 F2+ 84 D2 C2 A2 254 B2
Z3 Z4 T3 T4 Z3 Z4 T3 T4 VN 82 C3 A3 252 B3
Z1 Z2 T1 T2 Z1 Z2 T1 T2 F1 81 D1 C1 A1 251 B1
ET/ETA/ETV trip system Remote operation

UC1 : UC2 : SDE: Fault-trip indication contact (supplied as standard)
Z1-Z5 zone selective interlocking T1, T2, T3, T4=external neutral MN: Undervoltage release
Z1=ZSI OUT SOURCE MX: Shunt release (standard for Electrical breaker)
Z2=ZSI OUT ; Z3 = ZSI IN SOURCE XF: Closing release (standard for Electrical breaker)
Z4 =ZSI IN ST (short time) PF: “Ready to close”contact
Z5 =ZSI IN GF (earth fault) UC3 : MCH: Gear motor (standard for Electrical breaker)
F2+, F1-: external 24 V DC power supply
VN: external voltage connector (must be
connected to the neutral CT with a 3P
circuit breaker equipped with ETV trip system)
External sensors ( Neutral CT)

E47477
External sensor for earth-fault protection

The sensors, used with the 3P circuit breakers, are installed on the neutral
conductor for:
1. Residual type earth-fault protection(ET/ETA/ETV 6G trip system)
The rating of the sensor (CT) must be compatible with the rating of the circuit
breaker:
External sensor (CT). 1. MVS08 to MVS20: CT 400/2000;
2. MVS25 to MVS40: CT 1000/4000;
D-2
Indication contacts Chassis contacts
DB101409

OF4 OF3 OF2 OF1 OF14 OF13 OF12 OF11 CD3 CD2 CD1 CE3 CE2 CE1 CT3 CT2 CT1
44
34
24
14 144
134
124
114 834 824 814 334 324 314 934 924 914
42
32
22
12 142
132
122
112
832 822 812 332 322 312 932 922 912
41
31
21
11 141
131
121
111
831 821 811 331 321 311 931 921 911
Standard Optional Optional

OF 4
Standard OF 14
Optional CD3 Disconnected CE3 Connected CT3 Test
OF 3
ON/OFF OF 13
ON/OFF CD2 Position CE2 Position CT2 Position
OF 2
Indication contacts OF 12
Indication contacts CD1 Contacts CE1 Contacts CT1 Contacts
OF 1
OF 11
Key:
Drawout device only

XXX SDE1, OF1, OF2, OF3, OF4 supplied as standard
Interconnected connections
(only one wire per connection point)
D-3
Electrical diagrams EasyPact MVS
Earth-fault protection
Neutral Protection
External sensor (CT) for residual earth-fault protection

Connection of current-transformer secondary
DB125601
circuit for external neutral
VN
EasyPact MVS equipped with a ET/ETA/ETV 6G:
b Shielded cable with 2 twisted pairs
b T1 twisted with T2
b Maximum length 4 meters
b Cable cross-sectional area 0.4 to 1.5 mm2
b Recommended cable: Belden 9552 or equivalent
For proper wiring of neutral CT, refer to instruction
Bulletin 48041-082-03 shipped with it.
Do not remove factory-installed jumper between T1
and T2 unless neutral CT is connected.
If supply is via the top, follow the shematics. ET/ETA/ETV 6G
If supply is via the bottom, control wiring is identical; for
the power wiring, H1 is connected to the source side,
H2 to the load side.
For four-pole versions, for residual earth-fault
protection, the current transformer for the external
neutral is not necessary.
Shield Drain
External VN
Neutral CT
Neutral protection
b Three pole circuit breaker:
v Neutral protection is impossible
b Four pole circuit breaker:
v The current transformer for external neutral is not
necessary
D-4
Zone Selective Interlocking
Zone selective interlocking

Zone-selective interlocking is used to reduce the
DB101420
electrodynamic forces exerted on the installation by shortening
the time required to clear faults, while maintaining time
discrimination between the various devices.
A pilot wire interconnects a number of circuit breakers
equipped with ET range of trip system, as illustrated in the
diagram above.
The control unit detecting a fault sends a signal upstream and
checks for a signal arriving from downstream. If there is a signal
from downstream, the circuit breaker remains closed for the full
duration of its tripping delay. If there is no signal from
downstream, the circuit breaker opens immediately, regardless
of the tripping-delay setting.
Fault 1.
Only circuit breaker A detects the fault. Because it receives no
signal from downstream, it opens immediately, regardless of its
tripping delay set to 0.3.
Fault 2.
Circuit breakers A and B detect the fault. Circuit breaker A
receives a signal from B and remains closed for the full duration
of its tripping delay set to 0.3. Circuit breaker B does not
receive a signal from downstream and opens immediately, in
spite of its tripping delay set to 0.2.
Wiring
b Maximum impedance: 2.7 W / 300 m
b Capacity of connectors: 0.4 to 2.5 mm2
b Wires: single or multicore
b Maximum lenght: 3000 m
b Limits to device interconnection:
v The common ZSI - OUT (Z1) and the output ZSI - OUT (Z2)
can be connected to a maximum of 10 upstream device

v A maximum of 100 downstream devices may be connected
to the common ZSI - IN (Z3) and to an input ZSI - IN CR ( Z4)
or GF (Z5)
D-5
Electrical diagrams EasyPact MVS
24 V DC external power supply
AD module
b The 24 V DC external power-supply (AD module) for the ET Trip system (F1- F2+)
DB128383
is not required for basic protections LSIG

b With ETA/ETV, it is recommended to connect 24 V DC external power-supply
(AD module) to the Micrologic control unit (F1- F2+) in order to keep available the
display and the energy metering, even if Current < 20 % In
Note: In case of using the 24 V DC external power supply (AD module), maximum cable length
between 24 V DC (G1, G2) and the control unit (F1-, F2+) must not exceed 10 meters.
The internal voltage taps are connected to the bottom side of the circuit breaker.
ETA/ETV trip system

Connection
The maximum length for each conductor supplying power to the trip unit is 10 m.
Do not ground F2+, F1-, or power supply output:
b The positive terminal (F2+) on the trip unit must not be connected to earth ground
b The negative terminal (F1-) on the trip unit must not be connected to earth ground
b The output terminals (- and +) of the 24 V DC power supply must not be grounded
Reduce electromagnetic interference:
b The input and output wires of the 24 V DC power supply must be physically
separated as much as possible
b If the 24 V DC power supply wires cross power cables, they must cross
perpendicularly. If this is not physically possible, the power supply conductors
must be twisted together
b Power supply conductors must be cut to length. Do not loop excess conductor
D-6
D-7
Additional
characteristics
EasyPact MVS Additional characteristics
Tripping curves E-2
E-1
Additional Tripping curves
characteristics
ET range of trip system - 2I
DB105112
ET range of trip system - 5S, 6G

DB105113
E-2
Earth fault protection (ET range of trip system - 6G)
DB101505
(1)
Ig = In x... A B C D E F G H I
In y 400 A 0.3 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
400 A < In y 1000 A 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1
In u 1250A 500 640 720 800 880 960 1040 1120 1200
E-3
Catalogue numbers
and order form
EasyPact MVS Catalogue numbers
and order form
Tripping curves E-2
Nomenclature F-2
EasyPact MVS 800 to 4000A F-3
EasyPact MVS fixed 50kA F-3
EasyPact MVS fixed 65kA F-4
EasyPact MVS withdrawable 50kA F-5
EasyPact MVS withdrawable 65kA F-7
EasyPact MVS F-8
Connection F-8
ET Trip System & accessories F-9
Remote operation F-10
Chassis locking and accessories F-12
Clusters F-13
Circuit breaker locking and accessories F-14
Mechanical interlocking for source changeover F-15
Indication contacts F-16
Instructions F-17
Order form F-18
F-1
Catalogue numbers Nomenclature
and order form
Range Current rating Type Pole Operating mechanism Installation Protection No. Type
EasyPact MVS (from 800 to 4000A) Icu=Ics=Icw (1 sec)=50kA & 65kA
MVS 08 N 3 M F 2 L
10 H 4 N W 5 A
12
O 6 V
16 P 0 D
20 Q
25 R
32 S
40 T
3 2 1 1 1 1 1 1 11 digits
Type
L Basic protection
A Protection+current metering
V Protection+voltage metering
D Switch disconnector
Protections No.
2 LI protection
5 LSI protection
6 LSIG protection
0 No protection for switch disconnector
Type of installation
F Fixed
W Withdrawable/drawout
Operating mechanism
M Manually operated ACB/SD
N Electrical 200/240 VAC MCH + XF + MX
O Electrical 110/130 VAC MCH + XF + MX
P Electrical 380/415 VAC MCH + XF + MX
Q Electrical 200/250 VDC MCH + XF + MX
R Electrical 100/125 VDC MCH + XF + MX
S Electrical 48/60V DC MCH + XF + MX
T Electrical 24/30V DC MCH + XF + MX
Number of poles
3P 3 Poles
4P 4 Poles
Type based on breaking capacity

N Circuit breaker/ switch disconnector Icu=Ics=Icw(1sec)=50kA
H Circuit breaker/ switch disconnector Icu=Ics=Icw(1sec)=65kA
Current rating
08 800A
10 1000A
12 1250A
16 1600A
20 2000A
25 2500A
32 3200A
40 4000A
Example 1 MVS32N4NW6L
MVS 32 N 4 N W 6 L
EasyPact 3200A 50kA 4 Pole Electrical operated Withdrawable LSIG protection Basic trip unit with LED indications
MVS 240V AC type
Example 2 MVS16H3MF0D
MVS 16 H 3 M F 0 D
EasyPact 1600A 65kA 3 Pole Manual operated Fixed No protection Switch disconnector
MVS
F-2
EasyPact MVS 800 to 4000A
EasyPact MVS fixed 50kA
EasyPact MVS fixed type 50kA with ET trip unit

3P 4P
ET2I ET5S ET6G ET2I ET5S ET6G
CDB500062
Manual 800A MVS08N3MF2L MVS08N3MF5L MVS08N3MF6L * * *

1000A MVS10N3MF2L MVS10N3MF5L MVS10N3MF6L * * *
Electrical 800A MVS08N3NF2L MVS08N3NF5L MVS08N3NF6L * * *
240V AC(1) 1000A MVS10N3NF2L MVS10N3NF5L MVS10N3NF6L * * *
1250A MVS12N3NF2L MVS12N3NF5L MVS12N3NF6L * * *
EasyPact MVS fixed type 50kA Switch Disconnector

3P 4P
Manual 800A MVS08N3MF0D *
CDB500062
1000A MVS10N3MF0D *
1250A MVS12N3MF0D *
1600A MVS16N3MF0D *
2000A MVS20N3MF0D *
2500A MVS25N3MF0D *
3200A MVS32N3MF0D *
4000A MVS40N3MF0D *
Electrical 800A MVS08N3NF0D *
240V AC(1) 1000A MVS10N3NF0D *
1250A MVS12N3NF0D *
1600A MVS16N3NF0D *
2000A MVS20N3NF0D *
2500A MVS25N3NF0D *
3200A MVS32N3NF0D *
4000A MVS40N3NF0D *
(1) Supplied with spring charge motor(MCH), opening release(MX) and
closing release(XF) with 240V AC control voltage rating.
* Non-standard configured products.
Use customer order form in page F-9 to order non-standard products
F-3
Catalogue numbers EasyPact MVS 800 to 4000A
and order form EasyPact MVS fixed 65kA
EasyPact MVS fixed type 65kA with ET trip unit

3P 4P
CDB500062
Manual 800A MVS08H3MF2L MVS08H3MF5L MVS08H3MF6L * * *

1000A MVS10H3MF2L MVS10H3MF5L MVS10H3MF6L * * *
Electrical 800A MVS08H3NF2L MVS08H3NF5L MVS08H3NF6L * * *
240V AC(1) 1000A MVS10H3NF2L MVS10H3NF5L MVS10H3NF6L * * *
1250A MVS12H3NF2L MVS12H3NF5L MVS12H3NF6L * * *
EasyPact MVS fixed type 65kA switch disconnector

3P 4P
CDB500062
Manual 800A MVS08H3MF0D *

1000A MVS10H3MF0D *
1250A MVS12H3MF0D *
1600A MVS16H3MF0D *
2000A MVS20H3MF0D *
2500A MVS25H3MF0D *
3200A MVS32H3MF0D *
4000A MVS40H3MF0D *
Electrical 800A MVS08H3NF0D *
240V AC(1) 1000A MVS10H3NF0D *
1250A MVS12H3NF0D *
1600A MVS16H3NF0D *
2000A MVS20H3NF0D *
2500A MVS25H3NF0D *
3200A MVS32H3NF0D *
4000A MVS40H3NF0D *
F-4
EasyPact MVS withdrawable 50kA
EasyPact MVS withdrawable type 50kA with ET trip unit

3P 4P
CDB500048
Manual 800A MVS08N3MW2L MVS08N3MW5L MVS08N3MW6L * * *

1000A MVS10N3MW2L MVS10N3MW5L MVS10N3MW6L * * *
Electrical 800A MVS08N3NW2L MVS08N3NW5L MVS08N3NW6L * * *
240V AC(1) 1000A MVS10N3NW2L MVS10N3NW5L MVS10N3NW6L * * *
1250A MVS12N3NW2L MVS12N3NW5L MVS12N3NW6L * * *
EasyPact MVS withdrawable type 50kA with ETA trip unit

3P 4P
ETA2I ETA5S ETA6G ETA2I ETA5S ETA6G
CDB500048
Manual 800A MVS08N3MW2A MVS08N3MW5A MVS08N3MW6A MVS08N4MW2A MVS08N4MW5A MVS08N4MW6A

1000A MVS10N3MW2A MVS10N3MW5A MVS10N3MW6A MVS10N4MW2A MVS10N4MW5A MVS10N4MW6A
Electrical 800A MVS08N3NW2A MVS08N3NW5A MVS08N3NW6A MVS08N4NW2A MVS08N4NW5A MVS08N4NW6A
240V AC(1) 1000A MVS10N3NW2A MVS10N3NW5A MVS10N3NW6A MVS10N4NW2A MVS10N4NW5A MVS10N4NW6A
1250A MVS12N3NW2A MVS12N3NW5A MVS12N3NW6A MVS12N4NW2A MVS12N4NW5A MVS12N4NW6A
F-5
Catalogue numbers EasyPact MVS 800 to 4000A
and order form EasyPact MVS withdrawable 50kA
EasyPact MVS withdrawable type 50kA with ETV trip unit

3P 4P
ETV2I ETV5S ETV6G ETV2I ETV5S ETV6G
CDB500048
Manual 800A MVS08N3MW2V MVS08N3MW5V MVS08N3MW6V MVS08N4MW2V MVS08N4MW5V MVS08N4MW6V

1000A MVS10N3MW2V MVS10N3MW5V MVS10N3MW6V MVS10N4MW2V MVS10N4MW5V MVS10N4MW6V
Electrical 800A MVS08N3NW2V MVS08N3NW5V MVS08N3NW6V MVS08N4NW2V MVS08N4NW5V MVS08N4NW6V
240V AC(1) 1000A MVS10N3NW2V MVS10N3NW5V MVS10N3NW6V MVS10N4NW2V MVS10N4NW5V MVS10N4NW6V
1250A MVS12N3NW2V MVS12N3NW5V MVS12N3NW6V MVS12N4NW2V MVS12N4NW5V MVS12N4NW6V
EasyPact MVS withdrawable type 50kA switch disconnector

3P 4P
CDB500048
Manual 800A MVS08N3MW0D MVS08N4MW0D

1000A MVS10N3MW0D MVS10N4MW0D
Electrical 800A MVS08N3NW0D MVS08N4NW0D
240V AC(1) 1000A MVS10N3NW0D MVS10N4NW0D
1250A MVS12N3NW0D MVS12N4NW0D

F-6
EasyPact MVS withdrawable 65kA
EasyPact MVS withdrawable type 65kA with ET trip unit

3P 4P
CDB500048
Manual 800A MVS08H3MW2L MVS08H3MW5L MVS08H3MW6L * * *

1000A MVS10H3MW2L MVS10H3MW5L MVS10H3MW6L * * *
Electrical 800A MVS08H3NW2L MVS08H3NW5L MVS08H3NW6L * * *
240V AC(1) 1000A MVS10H3NW2L MVS10H3NW5L MVS10H3NW6L * * *
1250A MVS12H3NW2L MVS12H3NW5L MVS12H3NW6L * * *
EasyPact MVS withdrawable type 65kA switch disconnector

3P 4P
Manual 800A MVS08H3MW0D *
CDB500048
1000A MVS10H3MW0D *
1250A MVS12H3MW0D *
1600A MVS16H3MW0D *
2000A MVS20H3MW0D *
2500A MVS25H3MW0D *
3200A MVS32H3MW0D *
4000A MVS40H3MW0D *
Electrical 800A MVS08H3NW0D *
240V AC(1) 1000A MVS10H3NW0D *
1250A MVS12H3NW0D *
1600A MVS16H3NW0D *
2000A MVS20H3NW0D *
2500A MVS25H3NW0D *
3200A MVS32H3NW0D *
4000A MVS40H3NW0D *
F-7
Catalogue numbers EasyPact MVS
and order form Connection
Connection
3P 4P
Fixed circuit breakers
Rear connection (vertical or horizontal mounting) / Replacement kit (3 or 4 parts)
800-2000 A Vertical 47964 47965

E46445
Horizontal 47964 47965

2500/3200 A Vertical 47966 47967
Vertical mounting.
4000 A Vertical 47968 47969
E46446
Horizontal mounting.
Installation manual MVS21735
Drawout circuit breakers
Rear connection (vertical or horizontal mounting) / Replacement kit (3 or 4 parts)
800-2000 A Vertical 47964 47965
E46445

2500/3200 A Vertical 47966 47967
Vertical mounting. 4000 A Vertical 47968 47969
E46446
Horizontal mounting.
Connection accessories
Interphase barriers / Replacement kit (3 parts)
For fixed rear-connected circuit breaker 48599 48599
E46428
For drawout rear-connected circuit breaker 48600 48600

F-8
ET Trip System & accessories
ET trip units & accessories

Trip units
ET2I protection relay for MVS 65477
CDB500057
ET5S protection relay for MVS 65478
ET6G protection relay for MVS 67479
ETA2I protection relay for MVS 65577
ETA5S protection relay for MVS 65578
ETA6G protection relay for MVS 65579
ETV2I protection relay for MVS MVS15501

ETV5S protection relay for MVS MVS15502
ETV6G protection relay for MVS MVS15503
Battery + cover
Battery (1 part) 33593
E95540
Cover (1 part) 33592
menu
External sensors
External sensor for earth-fault protection (TCE) / 1 part
Sensor rating 400/2000 A 34035
E46671
1000/4000 A
34036
External power supply module (AD) / 1 part

24-30 V DC
54440
DB105360
48-60 V DC
54441
100-125 V DC
54442
110-130 V AC
54443
200-240 V AC
54444
380-415 V AC
54445
Test equipments / 1 Part

Hand held test kit (HHTK) 33594
CDB500038
F-9
and order form Remote operation
Remote operation
Gear motor
MCH (1 part)
E95172
AC 50/60 Hz 100/130 V
47893
200/240 V
47894
380/415 V
47896
DC 24/30 V
47888
48/60 V
47889
100/125 V
47890
200/250 V
47891
Terminal block (1 part) For fixed circuit breaker 47074
E95169
E95171
For drawout circuit breaker 47849
Fixed. Drawout.
Closing release (XF)
Standard coil (1 part)
E95170
AC 50/60 Hz 24/30 V DC, 24 V AC

33659
DC 48/60 V DC, 48 V AC
33660
100/130 V AC/DC
MVS15511
200/250 V AC/DC MVS15512
380/480 V AC MVS15513
E95169
E95171
Fixed. Drawout.
Opening release (MX)
Standard coil (1 part)
E95170
AC 50/60 Hz 24/30 V DC, 24 V AC

33659
DC 48/60 V DC, 48 V AC
33660
100/130 V AC/DC
33661
200/250 V AC/DC
33662
380/480 V AC
33664
E95169
E95171
Fixed. Drawout.
F-10
Remote operation
Undervoltage release MN
Undervoltage release (1 part)
E95170
AC 50/60 Hz 24/30 V DC, 24 V AC 33668

DC 48/60 V DC, 48 V AC 33669
100/130 V AC/DC 33670
200/250 V AC/DC 33671
380/480 V AC 33673
E95169
E95171
Fixed. Drawout.
MN delay unit
MN delay unit (1 part)
E46694
R (non-adjustable) Rr (adjustable)
AC 50/60 Hz 48/60 V AC/DC 33680
DC 100/130 V AC/DC 33684 33681
200/250 V AC/DC 33685 33682
380/480 V AC/DC 33683
F-11
and order form Chassis locking and accessories
Chassis locking
“Disconnected” position locking / 1 part
By padlocks
E46451
VCPO Standard
By Profalux keylocks
Profalux 1 lock with 1 key + adaptation kit 64934
2 locks 1 key + adaptation kit 64935
Profalux 1 lock+ 1 key (without adaptation kit) 42888
Profalux 2 locks + 1 key (without adaptation kit) 42878
Adaptation kit (without key locks) 48564
By Ronis keylocks
Ronis 1 lock with 1 key + adaptation kit 64937
2 locks 1 key + adaptation kit 64938
Ronis 1 lock+ 1 key (without adaptation kit) 41940
Ronis 2 locks + 1 key (without adaptation kit) 41950
Door interlock / 1 part
Right and left-hand side of chassis (VPECD or VPECG) 47914
E46452

Chassis accessories
Auxiliary terminal shield (CB) / 1 part
800/4000 A 3P 64942
E46458
4P 48596

Safety shutters + locking block / 1 part
800/4000 A 3P 48721
E46459
4P 48723

Shutter locking block (for replacement) / 1 part
2 parts for 800/4000 A 48591
E46460

Earthing kit for chassis
3P 4P
Types for N/H/NA/HA
48433 48434
F-12
Clusters
Clusters
1 disconnecting contact cluster for chassis (see table below) (part 1) 33166
E95538
Table : number of clusters required for the different chassis models

Chassis rating (A) EasyPact MVS(3P) EasyPact MVS(4P)
N H NA HA N H NA HA
800 12 12 12 12 16 16 16 16
1000 12 12 12 12 16 16 16 16
1250 12 12 12 12 16 16 16 16
1600 12 12 12 12 16 16 16 16
2000 12 12 12 12 16 16 16 16
2500 24 12 24 12 32 16 32 16
3200 36 36 36 36 48 48 48 48
4000 42 42 42 42 56 56 56 56
Racking handle
Racking handle 47944
E95561
F-13
and order form Circuit breaker locking and accessories
Circuit breaker locking

Pushbutton locking device / 1 part
By padlocks 48536
E46666

OFF position locking / 1 part
By Profalux keylocks
E46735
Profalux 1 lock with 1 key + adaptation kit 64928

2 locks 1 keys + adaptation kit 64929
Profalux 1 lock+ 1 key (without adaptation kit) 42888
Profalux 2 locks + 1 key (without adaptation kit) 42878
By Ronis keylocks
Ronis 1 lock with 1 key + adaptation kit 64931
2 locks 1 keys + adaptation kit 64932
Ronis 1 lock+ 1 key (without adaptation kit) 41940
Ronis 2 locks + 1 key (without adaptation kit) 41950
Mechanical operation counter / 1 part
Operation counter CDM 48535
DB125617

Escutcheon and accessories / 1 part
Fixed Drawout
CDB500061
E46669
E46670
Escutcheon 48601 48603

Transparent cover (IP 54) - 48604
Escutcheon blanking plate 48605 48605
Escutcheon Cover Blanking plate Installation manual MVS21736

Front cover (3P / 4P) / 1 part
MVS Front cover MVS21808
CDB500058

Spring charging handle / 1 part
Spring charging handle 47940
E95536

Arc chute for EasyPact MVS / 1 part
3P 4P
CDB500059
Type N/NA 3 x MVS21807 4 x MVS21807

Type H/HA 3 x MVS21807 4 x MVS21807
F-14
Mechanical interlocking for source
changeover
Mechanical interlocking for source changeover

Interlocking of 2 devices using cables (1)
Choose 2 adaptation sets (1 for each device + 1 set of cables)
CDB500053
1 adaptation fixture for EasyPact MVS fixed devices 47926

1 adaptation fixture for EasyPact MVS drawout devices 47926
1 set of 2 cables 33209
(1) Can be used with any combination of EasyPact MVS, fixed or drawout devices.

Interlocking of 3 devices using cables
Choose 3 adaptation (including 3 adaptation fixtures + cables)
CDB500060
3 sources, only 1 device closed, fixed or drawout devices 48610

2 sources + 1 coupling, fixed or drawout devices 48609
2 normal + 1 replacement source, fixed or drawout devices 48608
F-15
and order form Indication contacts
Indication contacts
ON/OFF indication contacts (OF) / 12 parts
1 additional block of 4 contacts 47887
E46689
Wiring For fixed circuit breaker 47074

“Ready to close” contact (1 max.) / 1 part
1 changeover contact (5 A - 240 V)
47080
E46438
Wiring For fixed circuit breaker

47074
For drawout circuit breaker

47849

“Connected, disconnected, test position” indication contact (carriage switches) / 1 part
Changeover contacts 6 A - 240 V
33170
E46661

Auxiliary terminals for chassis alone
3 wire terminal (1 part) 47849
6 wire terminal (1 part)

47850
Jumpers (10 parts)

47900
F-16
Instructions
Instructions
EasyPact MVS User Manual (English) MVS21734
Fixed & drawout circuit breaker MVS21735
Circuit breaker accessories MVS21736
Chassis accessories MVS21737
Interlocking of EasyPact MVS devices MVS21738
F-17
and order form
Order ref no:

EasyPact MVS
Date:
Circuit breaker and Switch-disconnectors

Product ref no:
Customer Order form
To indicate your choices, check the applicable square boxes √ Indication contacts
OF - ON/OFF indication contacts
And enter the appropriate information in the rectangles Standard 1 block of 4 OF 10 A-240/380V AC
Additional 1 block of 4 OF 6 A-240/380V AC
SDE - “fault-trip” indication contact
Circuit breaker or switch-disconnector Quantity Standard 1 SDE 5A -240/380V AC
Optional
Rating A Carriage switches 8 A-240/380V AC
Circuit breaker N/ H CE - “Connected” position Max. 3 qty
Switch Disconnector NA/HA CT - “Test” position Max. 3 qty
Number of poles 3 or 4 CD - “Disconnected” position Max. 3 qty
Type of equipment Fixed Remote tripping MN - Under voltage release V
Draw out with chassis R - Delay unit (fixed time delay) 0.25s
Operating Mechanism Manual Operated Rr - Adjustable delay unit 0.5s……3s
Electrical Operated AD - External power-supply module V
MCH - Gear motor V TCE - External sensor (NCT) for neutral of 3 Phase-4 Wire systems 400/2000A
XF - Closing coil V TCE - External sensor (NCT) for neutral of 3 Phase-4 Wire systems 1000/4000A
MX - Shunt/Opening voltage release V PF - “Ready to close” contact 5A-240/380V AC
ET Range of Trip System Locks
ET- Without display 2I 5S 6G VBP - ON/OFF pushbutton locking (by transparent cover using padlock)
ETA - Current Metering 2I 5S 6G VSPO - Device locking in OFF position by key lock (Only one key lock per ACB possible)
ETV - Voltage Metering 2I 5S 6G Key lock kit (w/o key lock) Profalux Ronis
LR - Long-time rating plug Standard 0.4 to 1 Ir 1 key lock Profalux Ronis
Connection 2 identical key locks, 1 key Profalux Ronis
Horizontal Top Bottom Chassis locking in “Disconnected” position:
Vertical Top Bottom VSPD - by key locks Key lock kit (w/o key lock) Profalux Ronis
1 key lock Profalux Ronis
Trip System functions: 2 identical key locks, 1 key Profalux Ronis
2I : Basic protection (long time + inst.)
5S : Selective protection (long time + short time + inst.)

Door Interlock - VPEC On left-hand side of chassis (LH)
6G : Selective + earth-fault protection
On right-hand side of chassis (RH)
(long time + short time + inst. + earth-fault)
Mechanical Interlocking of ACBs with Cable
1 Normal source & 1 replacement source (2 devices)
2 normal + 1 replacement source, fixed or drawout devices
2 sources with coupler on busbars (3 devices)
3 sources, only 1 device closed, fixed or drawout devices
Accessories
VO - Safety shutters on chassis Standard
CDP - Escutcheon Standard
Safety Shutter locking blocks
CP - Transparent cover for escutcheon
OP - Blanking plate for escutcheon
CDM - Mechanical operation counter for MVS
CB - Auxiliary terminal shield fitted on chassis
EIP - Interphase barriers
HHTK - Hand held test kit
Notes:
Customer can provide only the reference no. of the product for the listed references. Kindly refer to product catalogue for list of references.
Customer to fill this order form for non-listed references.
All breakers will be provided with 1 OF (4 c/o contacts), 1 SDE (trip contact), Escutcheon (Panel sealing frame) as standard.
All draw-out type devices will be supplied with Chassis & safety shutter.
For Electrical operated devices, indicate the voltage ratings of MCH,XF & MX
Refer to product catalogue for available voltage ratings of MCH/XF/MX/MN & AD Module
The orientation of customer connecting terminals can be changed at site from Horizontal to vertical or vice-versa.
F-18
© 2013 - Schneider Electric - All rights reserved.
Schneider Electric Industries SAS As standards, specifications and designs change from time to time, please ask for confirmation
35, rue Joseph Monier of the information given in this publication.
CS 30323
F- 92506 Rueil Malmaison Cedex This document has been printed on ecological paper
RCS Nanterre 954 503 439 Design: Schneider Electric

Capital social 896 313 776 € Photos: Schneider Electric
www.schneider-electric.com Printed:
LVED211021EN 04-2013

MVS Catalog

Uploaded by

Copyright:

Available Formats

MVS Catalog

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MVS Catalog

Uploaded by

Copyright:

Available Formats

Low Voltage

LV power circuit breakers and switch-disconnectors

Exceptional Quality and safety Outstanding value for an

Buildings Industry Panelbuilders

> Performance without compromise

> 800 to 4000A ratings

Panel builders/ End Users Designers

Pay for what you need: Get outstanding durability with

100% With the quality you demand

Electrical diagrams D-1

and order form

General overview A-2

Detailed contents A-2

Circuit breakers and switch-disconnectors A-4

MVS08 to MVS40 A-4

Identifying ET range of trip system A-6

ET trip system A-8

ETA trip system A-10

ETV trip system A-12

ET range of trip system A-14

Accessories and test equipment A-14

Accessories and auxiliaries A-16

On the chassis A-19

Indication contacts A-20

Remote ON / OFF A-21

Remote tripping A-23

Source-changeover systems A-24

Mechanical interlocking A-24

Installation recommendations B-1

Dimensions and connection C-1

Electrical diagrams D-1

Additional characteristics E-1

Catalogue numbers and order form F-1

ET trip system page A-8

ETA trip system with current measurement page A-10

ET2I Trip System

ETV trip system with voltage measurement page A-12

External power-supply module

Connections page A-15

Locking page A-18

padlockable transparent cover

v “Fault” trip indication (SDE)

v Additional ON/OFF indication (OF)

v Ready-to-close contact (PF)

Remote operation page A-21

Accessories page A-25

Escutcheon Transparent cover

Mechanical operation counter

Source-changeover systems page A-24

v Interlocking between two devices

Interlocking of two devices

Circuit-breaker as per IEC 60947-2

(1) Refer page no. B-12 for details on temperature derating.

800 1000 1250 1600 2000 2500 3200 4000

EasyPact MVS circuit breakers equipped with ET range Dependability

Measurement of current and voltage helps users to radiated disturbances.

microprocessor. Protection functions are independent of measurement functions,

ensure system protection even at very low load currents.

Trip unit name codes ET2I: basic protection

b 2I for basic protection Protection: