Bridge Design Guide May 2019

GUIDE FOR
BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/

SYSTEMS
MAY 2019
American Bureau of Shipping

Incorporated by Act of Legislature of
the State of New York 1862
© 2019 American Bureau of Shipping. All rights reserved.

1701 City Plaza Drive
Spring, TX 77389 USA
Foreword (1 May 2019)
This Guide supersedes the previously published Guide for One Man Bridge Operated (OMBO) Ships
based on the IMO decision to discontinue the night time one man bridge experiment and shift emphasis to
bridge design and navigational systems.
The requirements for the functionality of the bridge design and layout, and the navigational equipment/
systems laid down in this Guide are intended to improve and optimize the work environment within the
bridge area and enhance the navigational capabilities, and safety of a vessel. The requirements for vessels
fitted with an integrated bridge system for navigational purpose is also included in this Guide.
The notations NBL, NBLES, NBLES+ and NIBS are introduced to replace the previous OMBO notation
and to define the expanded scope of the subject Guide.
Effective May 1, 2019, this Guide is revised to modify the existing NBLES Notation and incorporated the
new NLBES+ notation.
ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 ii

GUIDE FOR
BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/
SYSTEMS
CONTENTS
SECTION 1 General..................................................................................................7
1 Application...................................................................................... 7
1.1 ...........................................................................................7
1.2 ...........................................................................................7
1.3 ...........................................................................................7
3 Operational Assumptions................................................................7
3.1 ...........................................................................................7
3.2 ...........................................................................................7
5 Optional Notations.......................................................................... 7
5.1 Notation NBL (Navigational Bridge Layout)....................... 7
5.2 Notation NBLES and NBLES+ (Navigational Bridge
Layout and Equipment/systems)....................................... 7
5.3 Notation NIBS (Navigational Integrated Bridge
System)..............................................................................8
7 Regulations.....................................................................................8
9 Flag Administration and National Authorities..................................8
11 Definitions (December 2003).......................................................... 8
13 Plans and Data to be Submitted................................................... 10
13.1 Applicable to NBL, NBLES, NBLES+ and NIBS
Notations..........................................................................11
13.2 Applicable to NBLES, NBLES+ and NIBS Notations....... 11
13.3 Applicable to NIBS Notation............................................ 12
SECTION 2 Requirements for Notation NBL (Navigation Bridge Layout)........ 13

1 General......................................................................................... 13
3 Equipment Design and Construction............................................ 13
3.1 General (December 2003)............................................... 13
3.2 Fault Isolation.................................................................. 13
3.3 Replacement of Components.......................................... 13
3.4 Self-support..................................................................... 13
3.5 Configuration of Devices..................................................13
3.6 Instruments and Controls.................................................13
5 Bridge Arrangement and Working Environment........................... 14
5.1 Fields of Vision................................................................ 14
ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 iii
5.2 Control of Vessel..............................................................14
5.3 Routes and Working Clearances..................................... 15
5.4 Clear Height.....................................................................16
5.5 Workstations.................................................................... 16
5.6 Other Considerations.......................................................17
5.7 Tests and Sea Trials........................................................ 18
SECTION 3 Requirements for Notation NBLES (Navigational Bridge

Layout and Equipment/Systems) and Notation NBLES+............... 19
1 General......................................................................................... 19
3 Documentation, Type Approval and Performance Standards
of Navigational Equipment............................................................19
3.1 Documentation.................................................................19
3.2 Type-approved Equipment...............................................19
3.3 IMO's Performance Standards.........................................19
5 Manual Mode of Operation........................................................... 19
7 Alarm Systems..............................................................................19
7.1 Characteristics................................................................. 19
7.2 Audible Alarm Circuits..................................................... 19
7.3 Acknowledgment............................................................. 20
7.4 Disconnection and Resumption of Functions.................. 20
7.5 Built-in Testing................................................................. 20
9 Computerized Equipment............................................................. 20
11 Power Supply................................................................................20
11.1 Sources............................................................................20
11.2 Emergency Service..........................................................20
11.3 Loss of Power.................................................................. 20
13 Navigational Systems................................................................... 20
13.1 Heading Information System (December 2003).............. 21
13.2 Steering System.............................................................. 21
13.3 Speed Measuring System (December 2003)...................22
13.4 Depth Measuring System (December 2003)................... 22
13.5 Radar System.................................................................. 22
13.6 Automatic Traffic Surveillance System (December
2003)................................................................................22
13.7 Position Fixing System.................................................... 23
13.8 Watch Monitoring and Alarm Transfer System................ 23
13.9 Route Planning................................................................ 24
13.10 Vessel’s Automatic Identification System (December
2003)................................................................................24
15 Propulsion Engine/thruster Controls............................................. 24
17 Automatic Telephone System (December 2003).......................... 24
17.1 .........................................................................................24
17.2 .........................................................................................25
ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 iv

17.3 .........................................................................................25
19 Nautical Radiocommunication System......................................... 25
21 Workstations - Required Equipment............................................. 25
23 Operating/Technical Manual......................................................... 25
23.1 .........................................................................................25
23.2 .........................................................................................25
23.3 .........................................................................................25
23.4 .........................................................................................25
23.5 .........................................................................................25
25 Tests and Sea Trials..................................................................... 26
25.1 Applicable to All Relevant Navigational Equipment......... 26
25.2 Specific Equipment or System.........................................26
27 Survey After Construction.............................................................26
27.1 .........................................................................................26
27.2 .........................................................................................26
27.3 .........................................................................................27
27.4 .........................................................................................27
TABLE 1 Navigational Equipment for NBLES Notation.......................28

TABLE 2 Navigational Equipment for NBLES+ Notation.....................34
SECTION 4 Requirements for Notation NIBS (Navigational Integrated

Bridge System)...................................................................................36
1 General......................................................................................... 36
3 Integrated Bridge System (IBS).................................................... 36
3.1 Dimmer Control................................................................36
5 Centralized Bridge Workstation.................................................... 36
7 Central Alarm Panel......................................................................36
9 Route Planning Workstation......................................................... 37
11 Conning Information Display.........................................................37
13 Navigational System Requirements..............................................37
13.1 Course Information System (December 2003)................ 37
13.2 Speed Measuring System................................................37
13.3 Automatic Track-keeping System.................................... 37
13.4 Electronic Chart Display and Information System
(ECDIS) (December 2003).............................................. 37
15 Operating/Technical Manual......................................................... 37
17 Workstations - Required Equipment............................................. 37
19 Tests and Sea Trials (December 2003)........................................ 38
21 Survey After Construction.............................................................38
TABLE 1 Navigational Equipment for NIBS Notation (December

2003).................................................................................... 38
ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 v

APPENDIX 1 IMO Resolutions Referenced in this Guide (December 2003)....... 40
ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 vi

SECTION 1 General
1 Application
1.1
The requirements of this Guide are applicable to vessels possessing valid SOLAS certificates, and having
the bridge so designed and equipped as to enhance the safety and efficiency of navigation. When a vessel
is designed, built and surveyed in accordance with the requirements of this Guide, and when found
satisfactory, a classification notation as specified in 1/5 will be granted. Application of the requirements of
this Guide is optional.
1.2
The composition and qualifications of the crew remains the responsibility of the flag Administrations.
1.3
(December 2003) The design and layout of navigational equipment is to be based on sound ergonomic
principles. The ABS Guidance Notes on Ergonomic Design of Navigation Bridges may be used as a
supplement.
3 Operational Assumptions
The requirements contained in this Guide are based on the following assumptions:
3.1
Plans for emergencies and the conditions under which the vessel is intended to operate are clearly defined
in an operational manual acceptable to the flag Administration. The manual should clearly state the bridge
crew composition required under any particular set of circumstances.
3.2
The requirements of the International Conventions on Standards of Training, Certification and
Watchkeeping for Seafarers (STCW) and other applicable statutory regulations are complied with.
5 Optional Notations
5.1 Notation NBL (Navigational Bridge Layout)

Where requested by the Owner, a vessel having its bridge found to comply with the requirements in Parts
A and B of this Guide, as applicable, and which has been constructed and installed under survey by the
Surveyor, will be assigned the notation NBL.
5.2 Notation NBLES and NBLES+ (Navigational Bridge Layout and Equipment/systems)
(1 May 2019)
Where requested by the Owner, a vessel which is found to comply with the requirements specified in Parts
A through C of this Guide and which has been constructed and installed under survey by the Surveyor, will
be assigned the notation NBLES or NBLES+.
ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 7

Section 1 General 1
5.3 Notation NIBS (Navigational Integrated Bridge System)

Where requested by the Owner, a vessel which is fitted with an integrated bridge system (IBS) for
navigational purpose, is found to comply with the requirements specified in Sections 1 through 4 of this
Guide, and which has been constructed and installed under survey by the Surveyor, will be assigned the
notation NIBS.
7 Regulations
For the purpose of this Guide, the International Regulations for Preventing Collisions at Sea, and all other
relevant Regulations relating to radio and safety of navigation required by Chapters IV and V of 1974
SOLAS, as amended, are to be complied with. Valid statutory certificates issued by the pertinent flag
Administration are to be provided onboard the vessel and made available to the Surveyor upon request.
9 Flag Administration and National Authorities

Vessel owners or other interested parties are urged to consult the flag Administration and relevant National
Authorities concerning required manning levels on the bridge and any additional requirements which may
be imposed by them.
11 Definitions (December 2003)

The following list provides definitions of the terms used in this Guide:
Acquisition - The selection of those target vessels requiring a tracking procedure and the initiation of their
tracking.
Alarm - A visual and audible signal indicating an abnormal condition.
ARPA - Automatic Radar Plotting Aid.
Back-up Navigator - Any individual , generally an officer, who has been designated by the vessel master
to be on call if assistance is needed on the navigation bridge.
Bridge - That area from which the navigation and control of the vessel is exercised, including the
wheelhouse and bridge wings.
Bridge Wings - Those parts of the bridge on both sides of the vessel's wheelhouse which, in general,
extend to the vessel's side.
Bridge Wing Workstation - Workstation from which the vessel can be maneuvered, and operated during
unmooring and mooring, lock passage, taking or dropping the pilot, etc.
CPA(Closest Point of Approach) - The shortest target vessel-own vessel calculated distance that will occur
in case of no change in course and speed data.
Catwalk - Extension of a deck that is wide enough to allow the passage of a man.
Chart Area - Part of the wheelhouse situated and equipped for adequate performance of voyage planning/
plotting activities.
Commanding View - View without obstructions which would interfere with the navigator’s ability to
perform his immediate task.
Conning Position - Place on the bridge with a commanding view and which is used by navigators,
including pilots, when monitoring, maneuvering and controlling a vessel.
Course – The horizontal direction in which a vessel is steered or intended to be steered, expressed as an
angular distance from north. Course applies to direction over the water.

Section 1 General 1
Cross track Alarm – Comparison of the vessel’s position with the track (control error).
Display - Means by which a device presents visual information to the navigator, including conventional
instrumentation
ECDIS - (Electronic Chart Display and Information System) A system which displays hydrographic
information and the vessel's position along a pre-planned route.
Ergonomics - The study and design of working environments and their components, work practices, and
work procedures for the benefit of the worker’s productivity, health, comfort, and safety. Application of the
human factor in the analysis and design of equipment and working environment
FOV(Field of Vision) - Angular size of a scene that can be observed from a position in the vessel's bridge.
GLONASS - Global Orbiting Navigating Satellite Systems.
GMDSS - Global Maritime Distress and Safety System.
Heading – The horizontal direction in which the longitudinal axis of a ship actually points or heads at any
instant, expressed in angular units from a referenced direction.
Heading Monitor – Comparison of the heading source in use with a second independent heading sensor.
Helmsman - Person who steers the vessel.
Integrated Bridge System (IBS) - This system is defined as a combination of systems which are
interconnected in order to allow centralized access to sensor information or command/control from
workstations, with the aim of increasing safe and efficient vessel's management by suitable qualified
personnel. For the purpose of this Guide, the integrated bridge system pertains only to aspects dealing with
navigational, monitoring/alarming and communication functions as covered in this Guide.
Lookout - Activity carried out by sight and hearing as well as by all available means appropriate in the
prevailing circumstances and conditions so as to make a full appraisal of the situation and of the risk of
collision.
Main Workstation - See “navigation and traffic surveillance/maneuvering workstation”.
Manual Steering Workstation - Workstation from which the vessel can be steered by a helmsman,
possibly designed for working in a seated position.
Monitoring - Act of constantly checking equipment and environment in order to detect any changes.
Monitoring Workstation - Workstation from where equipment and environment can be checked
constantly; when several persons are working on the bridge it serves for relieving the navigator at the
navigation and traffic surveillance/maneuvering workstation and/or for carrying out advisory functions by
the master or pilot.
Navigation - All tasks relevant for deciding, executing and maintaining course and speed in relation to
waters and traffic.
Navigator - Person navigating, operating bridge equipment and maneuvering the vessel.
Navigation and Traffic Surveillance/maneuvering Workstation - Main workstation at which the

vessel's course, speed and position in relation to the waters and traffic can be controlled and monitored,
and where communication relevant to navigation can be performed. It is generally conceived for working
in seated or standing position with optimum visibility and integrated presentation of information and

Section 1 General 1
operating equipment. It shall be possible from this location to operate the vessel safely, in particular when
a fast sequence of action is required.
NAVTEX - A narrow-band direct printing telegraph equipment for reception of navigational and
meteorological warnings and urgent information to vessels.
Normal Sailing Conditions - When all systems and equipment related to navigation operate within design
limits, and environmental conditions such as weather and traffic do not cause excessive workload to the
officer of the watch.
Off Heading Alarm – Comparison of heading and preset heading (control error).
Officer of the Watch - Person responsible for safe navigating, operating of bridge equipment and
maneuvering of the vessel.
Operating/Technical Manual – Manuals or operational instructions for equipment/systems installed on

the bridge for the use of bridge personnel.
Position Monitor – Comparison of the position source in use with a second independent position sensor or
source.
Primary Bridge Navigational Equipment/Systems - For the purpose of this Guide, equipment/ systems
essential for the performance of primary bridge navigational functions are: gyro compass, radar, position-
fixing system and electronic chart system.
Public Rooms - Public rooms are those portions of the accommodations which are used for halls, dining
rooms, lounges and similar permanently enclosed spaces. For the purpose of this Guide, the library,
gymnasium, vessel's office and conference rooms need not be considered.
Radar Plotting - The whole process of target detection, tracking calculation, relative and true motion,
course, speed and display of information
Route Planning Workstation - Workstation at which vessel's operations are planned (i.e., route planning,
deck log, etc.) and where fixing and documenting all vessel's operation takes place.
Sea-going Vessel - Vessel navigating on the high seas, i.e. areas along coasts and from coast to coast.
TCPA - Time to Closest Point of Approach.
Track – The intended or desired horizontal direction of travel with respect to earth.
Tracking - The process of observing the sequential changes in the position of a target, to establish its
motion.
Way-point - Any of various intermediate points on a route.
Wheelhouse - Enclosed area of the bridge.
Workstation - Position at which one, or several tasks constituting a particular activity are carried out.
13 Plans and Data to be Submitted

(2011) Relevant plans and data are to be submitted for approval and/or information as follows. Plans
should generally be submitted electronically to ABS. However, hard copies will also be accepted.

Section 1 General 1
13.1 Applicable to NBL, NBLES, NBLES+ and NIBS Notations (1 May 2019)
i) Arrangements of windows, including dimensions and angles of inclination, dimensions of frames,
height above deck surface of upper and lower edges, type of glass, and details of clear view
arrangements (wipers, fresh water wash, de-icing/ de-misting, sunscreens, etc.).
ii) Fields of vision from the bridge workstations, including any blind sectors caused by obstructions
outside of the wheelhouse.
iii) Location and arrangement of workstations, including dimensions of consoles, layout of
instrumentation and controls, handrails, seating, etc.
iv) Clearances between floor and ceiling, or between floor and the underside of ceiling mounted
instruments, throughout the wheelhouse.
v) Arrangements for the general illumination of the bridge and the individual illumination of
workstation instruments and controls.
vi) Details of wheelhouse ventilation and heating systems.
vii) Details of internal communication systems operable from the bridge.
viii) Arrangements/details of exterior catwalk in front of bridge windows.
ix) Details of non-slip flooring. See 2/5.6.5.
x) Details of wheelhouse doors, including hold-back arrangements. See 2/5.6.8.
xi) Location of toilet. See 2/5.6.7.
xii) Arrangements for drainage of bridge decks. See 2/5.6.6.
xiii) Arrangements/details as to the measures to be taken to minimize hazards to personnel. See
2/5.6.10.
13.2 Applicable to NBLES, NBLES+ and NIBS Notations (1 May 2019)

13.2.1
A list of navigational equipment. This is to include for each item the manufacturer's name and
model number, together with copies of relevant type approval certificates.
13.2.2
A complete operational description of the relevant monitoring systems including a list of alarms
and displays. This may be accomplished by means of simplified block diagrams of navigation
equipment, internal communications systems and watch monitoring and alarm transfer systems,
and central alarm panel (where provided) including a list of alarms.
13.2.3
A simplified one-line diagram of the relevant systems described in 3/13 through 19. This is to
include power supplies to the bridge equipment, circuit protection ratings and settings, cable sizes,
rating of connected loads, detailed description and interactions, etc.
13.2.4
Operating/technical manuals for the installed navigational equipment/systems. A single copy only
is to be submitted for information. See 3/23.
13.2.5
Sea trial test schedule. A single copy only is to be submitted. See 3/25.

Section 1 General 1
13.3 Applicable to NIBS Notation

13.3.1
Details and arrangements of the workstations and systems described in Section 4.
13.3.2
(December 2003) In addition to A13.2.5, the sea trial program is to include test details of the
electronic chart display and information systems (EDCIS) and integrated bridge system (IBS).

SECTION 2 Requirements for Notation NBL (Navigation
Bridge Layout)
1 General
Vessels complying with Sections 1 through 2 of this Guide, will be assigned the notation NBL (Navigation
Bridge Layout).
3 Equipment Design and Construction
3.1 General (December 2003)

The design of navigational equipment is to be based on sound ergonomic principles in accordance with the
ABS Guidance Notes on Ergonomic Design of Navigation Bridges, as applicable. Its construction is to be
of robust, durable and flame retardant material incorporating the required degree of enclosure protection
(i.e., IP 20 for bridge installation and IP 56 for open deck installation). The requirements in 3/3 are
applicable to navigational related equipment required in this Guide
3.2 Fault Isolation

Circuits are to be designed to permit the isolation of a fault while maintaining functionality of the
remaining circuits or sub-components (i.e., using printed circuit cards, or modules, etc.) and are to allow
the easy and safe replacement of the faulted portion of the circuit.
3.3 Replacement of Components

Replaceable components are to be designed and arranged so that it will not be possible to connect them
incorrectly or use incorrect replacements.
3.4 Self-support
Workstations, panels, cabinets, etc., are to be secured to a solid foundation with sides and back suitably
protected. They are to be self-supported, or be braced to the bulkhead or the ceiling. In case the last
method is used, means of bracing is to be flexible to allow deflection of the deck without buckling the
assembly structure.
3.5 Configuration of Devices

Alarms, displays and control devices are to be arranged in a functional and logical manner to allow the
operator an easy and clear means of identification of each of the components or systems included therein.
Grouping of like system alarms, displays, and devices, and the use of labels and color schemes are some of
the methods to realize this intent. Precautions are to be taken to prevent the inadvertent operation of
controls that may lead to critical situations, i.e., care in the identification and location of switches,
activation controls, and handles, the use of recessed or covered switches and controls, and the arrangement
for sequential operation.
3.6 Instruments and Controls

Instruments and controls are to be designed to permit easy and correct reading by day and night and so
fitted as to minimize glare or reflection or being obscured by strong light. The following is applicable:

Section 2 Requirements for Notation NBL (Navigation Bridge Layout) 2
3.6.1 Digital Readout

Digital readout is not to be used where the reading changes rapidly so as to preclude the operator
from reading its changing value (i.e., numbers change is effected by snap action rather than by
continuous movement).
3.6.2 Circular Scale

For an index moving relative to a circular scale, the index is to move clockwise (or the scale is to
move counterclockwise) for increasing readings.
3.6.3 Linear Scale

For an index moving relative to a linear scale, the index is to be horizontal or vertical and the
pointer is to move to the right or upwards for increasing readings. Deviation from this norm will
be considered for special applications such as for water depth measurements.
3.6.4 Distinction
Controls or combined controls/indicators are to be visually and tactually distinguishable from
elements that only indicate (i.e., rectangular buttons may be used for control elements and round
lights for indicator elements).
3.6.5 Mechanical Control

The shape of mechanical controls are to indicate the method of operation of the control. Rotary
finite-position controls (e.g., stepped switches) are to have toggles or levers, whereas rotary
continuous-position controls (rheostats) are to have knobs or wheels except the steering control.
3.6.6 Light Contrast

Instruments providing information are to be presented on background of high contrast, emitting as
little light as possible by night. They are to be designed to show a light text on a dark non-
reflecting background at night.
3.6.7 Illumination and Lighting

All instruments and controls are to be provided with means of illumination. Such illumination is to
be adjustable to zero, except for the illumination of alarms and dimmer controls. Such items are to
remain visible at all times.
For the illumination of displays and alarms, red light (wave length 620 nm or higher) is to be used.
5 Bridge Arrangement and Working Environment
5.1 Fields of Vision

5.1.1 General
Requirements found in Section 3-6-1, “Visibility” of the Marine Vessel Rules are to be complied
with.
5.2 Control of Vessel

5.2.1 General
The relevant workstations are to be designed and positioned so that navigational and traffic
surveillance/ maneuvering, docking and other tasks may be performed by the officer of the watch
in cooperation with other persons manning individual workstations.
Workstations used for navigating and traffic surveillance/maneuvering, manual steering, voyage
planning and communication are not to cover a working area with an axis longer than 15 m (49 ft
3 in.).

Further, where workstations are widely separated, talkback facilities are to be provided so that
unhampered communications between workstations can be achieved under all operating
conditions.
5.2.2 Conning Position (December 2003)

An adequate conning position is to be provided in close proximity to the forward center window
and is to be arranged so as to enable the navigator(s) to watch the area immediately in front of the
bridge superstructure and observe all relevant information required to maintain a safe course and
speed of the vessel in narrow waters, harbor areas and during final passages without interfering
with the tasks of the bridge personnel. The rudder, propeller, thrust, pitch and operational mode
indicators, or other means to determine and display rudder angle, propeller revolutions, direction
of thrust and, if applicable, the force and direction of lateral thrust and the pitch and operational
mode, are all to be readable from the conning position(s)
However, if the view in the center-line is obstructed by large masts, cranes, etc., two additional
conning positions giving a clear view ahead are to be provided, one on the port side and one on the
starboard side of the center-line, no more than 5 m (16 ft 5 in.) apart from each other.
5.2.3 Navigation and Traffic Surveillance/Maneuvering Workstation

The navigation and traffic surveillance/maneuvering workstation is to be arranged so as to enable
the officer of the watch to carry out the required tasks and to provide him with all necessary
information so that he can carry out his functions from a seated or standing working position but
without being restricted to a specific location. In addition, this workstation is to be designed,
arranged and located within an area having sufficient space for not less than two operators, but
which would allow the workstation to be operated efficiently by one.
5.2.4 Route Planning Workstation

The route planning workstation is to enable the navigator to plan the intended voyage without
interfering with the actual navigation or maneuvering of the vessel.
5.2.5 Monitoring Workstation

From the monitoring workstation, it is to be possible to see and hear the persons at the navigation
and traffic surveillance/maneuvering workstation and steering workstations.
5.2.6 Manual Steering Workstation

The workstation for manual steering is preferably to be located on the vessel’s center-line. If the
workstation for manual steering is located off the center-line, special steering references are to be
provided (e.g., sighting marks forward). If the view ahead is obstructed by large masts, cranes,
etc., the steering workstation is to be located a distance to starboard of the center-line, sufficient to
obtain a clear view ahead.
5.2.7 Docking Workstations

The workstations for docking of the vessel are to enable the navigator, together with a pilot, to
observe all relevant external and internal operations which will affect the safe docking of the
vessel. Talkback facilities are to be provided between the docking workstations and the
wheelhouse when the distance from the wing extremity to the wheelhouse center-line is greater
than 10 m (32 ft 10 in.).
5.3 Routes and Working Clearances

5.3.1 Across Wheelhouse (1 July 2012)
A clear route across the wheelhouse from bridge wing to bridge wing is to be provided and its
width is to be at least 1.2 m (3 ft 11 in.). However, the width may be reduced to not less than 700
mm at any single point of obstruction subject to the following:

i) There is clear visibility for individuals on either side of the obstruction to see each other
as they approach the area of reduced width,
ii) the length of the obstruction along the passageway does not exceed 1 m (39.4 inches),
iii) there is sufficient room on either side of the obstruction to allow one individual to step
aside and allow another individual to pass through [i.e., at least 1.2 m (3 ft 11 in.)],
iv) the above actions will not interfere with any crew member at a station required to be
continuously manned, and
v) the attending Surveyor is satisfied that two (2) individuals traveling in opposite directions
can pass through the area of reduced width with only a very brief pause by one of the two
(2).
5.3.2 From Lower Decks

There are to be no obstructions between the points of entry to the bridge wings and wheelhouse
from lower decks and the clear route required in 2/5.3.1.
5.3.3 Between Workstations

The distance between adjacent workstations is to be sufficient to allow unobstructed passage. To
this end, the free passageway is to be at least 0.7 m (2 ft 4 in.) in width. The workstation operating
area is to be part of the workstation and not of the passageway.
5.3.4 Front Passage

The distance from the front bulkhead, or from any workstation and installations placed against the
front bulkhead, to any workstation or installations placed away from the bridge front is to be
sufficient for two persons to pass each other. This distance is preferably to be 1 m (3 ft 3 in.) but in
no case less than 0.8 m (2 ft 7 in.).
5.4 Clear Height

The clear ceiling height in the wheelhouse is to be designed with regard to the installation of overhead
panels and instruments. To this end, the clear height between the bridge deck surface covering and the
underside of the deck head beams is to be at least 2.25 m (7 ft 5 in.). The lower edge of deckhead mounted
equipment is to be at least 2.1 m (6 ft 11 in.) above the deck in open areas, passageways and at standing
workstations.
5.5 Workstations
5.5.1 General
Instruments providing visual information to more than one person on duty are to be located for
easy viewing by all users concurrently, or if this is not possible, the instruments are to be
duplicated. Instruments displaying information to more than one workstation may be located
above the front windows if dimensions allow; such instruments are: vessel’s heading, wind, water
depth, speed, rate of turn, rudder angle, propeller revolutions (r/min), propeller pitch and time.
Configuration and dimensions as outlined in 2/5.5.2 and 2/5.5.3 do not apply to radar consoles.
5.5.2 Configuration
In general, workstations are to be divided into two parts if possible:
i) Vertical Part: Instruments dealing with information/presentation of data are to be placed

in the vertical part.
ii) Horizontal Part: Controls of the relevant equipment are to be placed in the horizontal
part.

5.5.3 Dimensions
i) Height: The height of workstations is not to interfere with the navigating bridge window’s
view requirements found in 3-6-1/1.3.4 and 3-6-1/1.3.5 of the Marine Vessel Rules:
ii) Width: Based on sound ergonomic principles, the width of workstations designed for
single person operation is not to exceed 1.6 m (5 ft 3 in.).
iii) Chart Table: The chart table is to be large enough to accommodate all chart sizes
normally used internationally for marine traffic. The dimensions of the chart table are to
be as follows: width, not less than 1.2 m (3 ft 11 in.); depth, not less than 0.85 m (2 ft 9
in.); height, not less than 0.9 m (2 ft 11 in.) and not more than 1 m (3 ft 3 in.).
Additionally, the chart table is to be provided with 10 mm (3/8 in.) slits in front and back
of the table to accommodate charts which are larger than the table.
5.5.4 Instruments and Controls
i) General: Instruments and controls are to be grouped according to their main functions;
these are: navigating and traffic surveillance/maneuvering, and communication.
ii) Line of Sight: Each instrument and control is to be placed with its face normal to the
navigator’s line of sight, or to the mean value if the navigator’s line of sight varies
through an angle.
iii) Glare: To avoid glare, all instruments and controls are to be positioned relative to the
operator considering the surrounding light sources.
iv) Transparent Covers: Transparent covers fitted over instrument(s) are to minimize
reflections.
v) Symbols/labels: The purpose of each control is to be clearly illustrated by symbols where
standard symbols have been internationally adopted, or indicated by a label in English.
5.6 Other Considerations

5.6.1 Lighting and Illumination
i) General: A satisfactory level of lighting is to be provided to enable personnel to complete
required bridge tasks at sea and port, day time and night time. To this end, individual task
areas are to have a greater luminance than the general lighting level.
ii) Lighting in Dark Hours: Relevant equipment fitted on the bridge is to be able to be
discerned during hours of darkness. This is to be achieved via internally or externally
located lighting. Red light is to be used to maintain dark adaptation whenever possible in
areas or on items of equipment, other than the chart table, requiring illumination in the
operational mode (see also 2/3.6.7). This is to include instruments and controls on the
bridge wings.
Additionally, in order to prevent red lights in the wheelhouse from being mistaken for navigation
lights by another vessel, indirect low level red lighting is to be fitted at deck level, especially for
internal doors and staircases.
5.6.2 Heating Ventilating and Air Conditioning (HVAC) System

An adequate HVAC system is to be provided in order to maintain the temperature of the
wheelhouse within the range of 14°C (57°F) to 30°C (86°F).
5.6.3 Sound Signals

Fixed vessel’s sound signals are to be placed as high as practicable and if possible, forward of the
bridge. External sound signals from vessels and fog signals that are audible on open deck, are to
be also audible inside the wheelhouse; to this end, a sound reception system (of a recommended
frequency range of 70 to 700 Hz) is to be provided to reproduce such signals inside the

wheelhouse (the opening of doors or windows is generally not to be accepted as an equivalent

solution).
5.6.4 Noise Levels

i) General: The noise level on the bridge is not to interfere with verbal communication,
mask audible alarms or be uncomfortable to the bridge personnel. In this respect, the
ambient noise level on the bridge in good weather is not to exceed 65 dB(A).
ii) Others: The noise of ventilation fans, engine intake fans and other noise sources are to be
excluded from the bridge operational area by suitable siting of the fans and associated
trunking.
5.6.5 Surfaces
i) Glare-free: All prepared surfaces are to be glare-free.
ii) Non-slip: The flooring throughout the bridge is to be provided with non-slip surfaces,
effective in both wet and dry locations.
5.6.6 Drainage
Bridge decks outside, including the wings, are to be provided with means for drainage.
5.6.7 Toilet Facilities

Toilet facilities are to be provided on or adjacent to the bridge, on the same level.
5.6.8 Doors
Doors to the bridge wings are to be capable of being operated with one hand. Means are to be
provided to hold the doors open.
5.6.9 Refreshment Facilities

Refreshment facilities and other amenities provided for the bridge personnel are to include means
for preventing damage to bridge equipment and injury to personnel resulting from the use of such
facilities and amenities.
5.6.10 Safety of Personnel

i) Sharp Edges and Protuberances: There are to be no sharp edges or protuberances which
could cause injury to personnel.
ii) Hand-rails or Grab-rails: Sufficient hand-rails or grab-rails are to be fitted to enable
personnel to move or stand safely in bad weather.
iii) Seat Securing: Where provisions for seating is made in the wheelhouse, means for
securing same are to be provided, having regard to storm conditions.
5.7 Tests and Sea Trials

During sea trials, navigational equipment and systems are to be tested to the satisfaction of the attending
Surveyor in accordance with a test program.

SECTION 3 Requirements for Notation NBLES (Navigational
Bridge Layout and Equipment/Systems) and
Notation NBLES+ (1 May 2019)
1 General (1 May 2019)

Vessels complying with Sections 1 through 3 of this Guide, will be assigned the notation NBLES
(Navigational Bridge Layout and Equipment/systems) and notation NBLES+. Equipment required for this
notation is listed in 3/27 TABLE 1 (found at end of Section 3) and for NBLES+ is listed in 3/27 TABLE 2.
3 Documentation, Type Approval and Performance Standards of

Navigational Equipment
3.1 Documentation
The manufacturer or assembler of the relevant navigational equipment required in this Guide is to provide
documented evidence indicating that the equipment meets the criteria specified in 3/3.2 and 3/3.3.
3.2 Type-approved Equipment

Navigational equipment is to be type approved to the satisfaction of the Administration in conformity with
appropriate performance standards acceptable to IMO.
3.3 IMO's Performance Standards

In general, relevant navigational equipment is to comply with IMO's Res. A.694(17), "General
requirements for shipborne radio equipment forming part of the global maritime distress and safety system
(GMDSS) and for electronic navigational aids", and those found in 3/13 and Section 4.
For ready reference, see also compilation of these performance standards in IMO Pub. 978-88.04.E (1988),
"Performance Standards for Navigational Equipment". See also Appendix A1 for a list of IMO Resolutions
referenced in this Guide.
5 Manual Mode of Operation

Navigational systems intended for automatic operation are to be fitted with manual operating facilities to
enable the officer of the watch to take the appropriate action in the event of failure of the automatic system.
For automatic systems for which this is not possible, an alternative system is to be provided as per 3/13.
7 Alarm Systems
7.1 Characteristics
Alarm systems are to be of the self-monitoring type and designed so that a fault in the alarm system is to
cause it to fail to the alarmed condition. Additionally, they are not to react to normal transient conditions or
spurious signals. Alarms are to be both audible and visual, and are to flash when first activated.
7.2 Audible Alarm Circuits

A fault in the visual alarm circuits is not to affect the operation of the audible alarm circuits.

Section 3 Requirements for Notation NBLES (Navigational Bridge Layout and Equipment/ 3
Systems) and Notation NBLES+
7.3 Acknowledgment
Alarms are to be acknowledged by manually changing the flashing display of the incoming alarm to a
steady display and by silencing the audible signal; the steady state light display is to remain activated until
the fault condition is rectified. Alarming of other faults that may occur during the acknowledgment process
is not to be suppressed by such action and is to be alarmed and displayed accordingly.
7.4 Disconnection and Resumption of Functions

Alarm circuits may be temporarily disabled for maintenance purposes or during initial start-up of
machinery provided that such action is clearly indicated to the officer of the watch. However, such alarm is
to be automatically re-activated after a preset time period has elapsed.
7.5 Built-in Testing

Alarm systems are to be provided with effective means for testing all audible and visual alarms and
indicating lamps without disrupting the normal equipment or system operation.
9 Computerized Equipment
Where computerized equipment are interconnected through a computer network, failure of the network is
not to prevent individual equipment from performing their individual functions.
11 Power Supply
11.1 Sources
Electrically operated systems and equipment covered in Section3 and 4 of this Guide are to be connected
to distribution panels placed in an accessible position on, or adjacent to but at the same level of the bridge;
each item of equipment is to be individually connected to its distribution panel. These panels are to be
supplied by two exclusive circuits, one fed from the main source of electrical power and one fed from an
emergency source of power. The power supplies to the distribution panels are to be arranged with
automatic changeover facilities between the two sources.
11.2 Emergency Service

The vessel's emergency source of power is to be of sufficient capacity to supply the navigational related
loads required in this Guide, in addition to other electrical loads as required in 4-8-2/5.5 of ABS Rules for
Building and Classing Marine Vessels.
11.3 Loss of Power

Following a loss of power which has lasted for 45 seconds or less, navigational equipment/systems
essential for the performance of primary bridge navigational functions (those are: gyro compass, radar,
position-fixing system and electronic chart system) are to be automatically reinstated to their pre-power-
loss configuration upon recovery from blackout, and all others are to be readily reinstated within five
minutes, with minimum operator intervention, by virtue of the emergency source of power and, where
necessary, by an uninterruptible power source.
Loss of power to the distribution panels is to activate an alarm.
13 Navigational Systems
In general, navigational equipment/systems installed onboard vessels are to be so arranged that failure of
one piece of navigational equipment will not reduce the vessel’s ability to perform the functions specified
in 3/13.1 through 3/13.9.

13.1 Heading Information System (December 2003)

The vessel is to be provided with continuous heading information at the appropriate workstations and at
the main steering position. To this end, a magnetic compass and a gyro compass having the capability to
determine the vessel's heading in relation to the geographic (true) North are to be provided. The magnetic
compass and the gyro compass are to comply with IMO's Res. A.382(X), "Performance Standard for
Magnetic Compass" and IMO's Res. A.424(XI), "Performance Standard for Gyro Compass", respectively.
In addition, a pelorus or compass bearing repeater, or other means to take bearings over an arc of the
horizon of 360 degrees, and a gyro compass heading repeater is to be provided. The following is to be
complied with:
13.1.1
In order to ensure the availability of heading information the vessel is to be fitted with an
independent gyro compass
13.1.2
Means for taking optical bearings is to be made available onboard the vessel.
13.1.3
Means are to be provided for correction of errors induced by speed and latitude.
13.1.4
When the position of the vessel cannot be received, the heading of the vessel is to be maintained
and such condition is to be alarmed.
13.2 Steering System

Means for manual and automatic steering of the vessel are to be provided. The steering system is to
comply with the following:
13.2.1
(December 2003) The automatic pilot with an on/off indicator is to comply with IMO’s Res.
A.342(IX), as amended by Annex 3 to MSC.64(67) “Performance Standard for Automatic Pilots”.
13.2.2
(December 2003) The automatic pilot equipment is to be monitored by an off-heading alarm,
which is to activate, when the actual heading deviates from a pre-set heading beyond a preset
limit, in the wheelhouse. This alarm is to be derived from a system independent from the
automatic steering system. The off-heading alarm is not to be released when setting a new course
reference.
The off-heading alarm may receive input from the gyrocompass, provided the compass is
independent of the automatic steering gear. The magnetic compass may be used as a signal input,
provided that same is used as a back-up to the gyro compass.
A heading control system is to work together with a track control system, adjusting its heading for
drift. The heading control system is to comply with IMO,s Res. MSC.64(67), Annex 3
“Recommendation on Performance Standards for Heading Control Systems” and the track control
system is to comply with IMO,s Res. MSC.74(69), Annex 2 “Recommendation on Performance
Standards for Track Control Systems”.
An overriding control device is to be provided at the navigation and traffic surveillance/ maneuvering
workstation. The override control is to enable instant take-over from the autopilot as well as from the
manual steering station.

13.2.4
For vessels of 50,000 GT and above, a rate of turn indicator is to be provided. The rate-of-turn
indicator is to comply with IMO's Res. A.526(13), “Performance Standards for Rate-of-Turn
Indicators”.
13.2.5
For vessels of 50,000 GT and above, a track controller, or other means to automatically perform
turns with a preset radius or rate of turn is to be provided.
13.3 Speed Measuring System (December 2003)

The vessel is to be fitted with the means for measuring speed and distance through the water. Vessels above
50,000 GT are also to be capable of measuring speed in the forward, aft and athwarthship directions. The
speed log is to comply with IMO's Res. MSC.96 (72), Annex 14 "Performance Standards for Devices to
Indicate Speed and Distance".
13.4 Depth Measuring System (December 2003)

The vessel is to be fitted with an echo sounder or equivalent for measuring the water depth under the keel.
An alarm is to be initiated when the water depth beneath the vessel is less than the predetermined value.
The echo sounder is to comply with IMO's Res. MSC.74(69), Annex 4 "Performance Standards for Echo-
Sounding Equipment".
13.5 Radar System

A 9 GHz radar or other means is to be provided in order to determine and display the range and bearing of
search and rescue transponders and of other surface craft, obstructions, buoys, shorelines and navigational
marks to assist in navigation and in collision avoidance. The radar installation is to comply with IMO's
Res. A.477(XII) as amended by Annex 4 to MSC.64(67), "Performance Standards for Navigational Radar
Equipment" and the following:
13.5.1
(December 2003) If the vessel’s minimum reflective cross section area is less than 100 m2, a radar
reflector or other means is to be provided so that the vessel can be detected by another vessel
navigating by radar. The radar reflector is to comply with IMO’s Res. A 384(X) “Performance
Standard for Radar Reflector”.
13.5.2
For vessels 3,000 GT and above, a second radar, independent of the 9 GHz radar, is to be
provided. Additionally, a change-over switch between these radar together with the means to
bypass the switch is to be provided.
13.6 Automatic Traffic Surveillance System (December 2003)

The vessel is to be fitted with an automatic traffic surveillance system to plot automatically the range and
bearing of other vessel's ability to determine collision risk. This traffic surveillance system is to comply
with IMO's Res. A823(19), "Performance Standards for Automatic Radar Plotting Aids (ARPA)". The
ARPA function may be independent or built into the radar equipment. The following is also to be complied
with:
13.6.1
The system is to be based on the assumption that all floating objects may come into a collision
course with own vessel if the object’s course is changed by 45° with its speed maintained. An
alarm is to be given to the navigator at a time which is to be adjustable in the range of 6 to 30
minutes, having regard to the danger, time to closest point of approach (TCPA). The system as a
whole is to feature the following capability:
a) true motion and relative motion modes,

b) daylight-visible display,
c) guard zone system, featuring adjustable parameters, notably alarm set for CPA and TCPA,
d) simulator function showing the likely effects of a course or speed change in relation to tracked
targets and
e) incorporated self-checking properties.
13.6.2
For vessels 3,000 GT and above, automatic acquisition and tracking of 20 radar targets and means
to simulate a trial maneuver is to be provided. Additionally, a heading or track controller or other
means to automatically control and keep to a heading and/or track is to be provided.
For vessels 10,000 GT and above, means to automatically control and keep the vessel in a straight track is
to be provided.
13.7 Position Fixing System

The vessel is to be fitted with at least two types of automatic position fixing systems for the waters she is
to navigate. These systems are to be capable of automatically and continually determining and displaying
the vessel's position. One of the systems is to be GPS or equivalent, and the other a Decca, LORAN-C,
GLONASS, or other means. The positioning equipment/system is to comply with IMO's Res. A819(19),
"Performance Standards for Shipborne Global positioning System (GPS) Receiver Equipment" and the
following:
13.7.1
Means for manually inputting required data in case of sensor failure, and the means to indicate the
system’s mode of operation i.e., manual or automatic, are to be provided.
13.7.2
A means to self-test the major functions of the system is to be provided.
13.7.3
(December 2003) Decca receivers are to comply with IMO Res. A.816(19), “Performance
Standard for Shipborne Decca Navigator Receivers”; Loran-C receivers are to comply with IMO
Res. A.818(19), “Performance Standard for Shipborne Loran-C and Chayka Receivers”;
GLONASS receivers are to comply with IMO Res. MSC. 113(73), Annex 26 “Performance
Standard for Shipborne GLONASS Receiver Equipment”.
13.8 Watch Monitoring and Alarm Transfer System

Means to monitor the alertness of the officer of the watch and alarm other bridge personnel if disability
occurs is to be provided. Additionally, conditions of danger to navigation caused by traffic or improper
course-keeping in relation to planned route are to be monitored and such adverse conditions are to be
alarmed at the bridge and at the locations specified herein.
13.8.1 Officer of the Watch Alertness-check System

a) General : A system is to be provided to monitor the alertness of the officer of the watch
present on the bridge. This system is not to cause undue interference with the
performance of bridge functions and it is to be designed and arranged that it cannot be
operated in a unauthorized manner (i.e. bypassed). The system is to be connected to the
alarm transfer system described in 3/13.8.2.
b) Periodic Verification (December 2003): The system used for periodic verification of the
watch alertness system is to be adjustable up to 12 minute intervals, and it is to be
arranged so that only the vessel’s master has access for enabling and disabling it (i.e.,
removing the fuses or keeping the acknowledgment button permanently depressed) and
for setting the appropriate intervals for a periodic verification.

c) Acknowledgment of Alertness-check Alarm : The system is to provide for the

acknowledgment by the officer of the watch at the navigation and traffic surveillance/
maneuvering workstation and at the monitoring workstation.
d) System Failure Alarm: An alarm is to operate on the bridge and at the spaces described
in 3/13.8.2.b, in the event of a failure of the alertness-check alarm system.
13.8.2 Alarm Transfer System (1 May 2018)
a) General (December 2003): A fixed alarm transfer system is to be provided and connected
to all vessel navigating officers’ cabins and public rooms.
b) Transfer of Alarms (December 2003): Alarms per the “Remark” column of item B17, a
through h, in 3/27 TABLE 1 are to be automatically transferred to the master’s cabin if
not acknowledged at the bridge within 30 seconds. Additionally, a selector switch is to be
provided in the event the master deems it necessary to also transfer the aforementioned
alarms to the selected back-up navigator’s cabins and public rooms.
c) Back-up Navigator Call-alarm : Provisions are to be made at the bridge to activate the
back-up navigator call-alarm. This alarm is to be audible in all the spaces described in
3/13.8.2.b. The fixed installation required under 3/13.8.2.a may serve this purpose.
d) Portable Communication Device : A wireless portable device allowing two-way
communication with the officer of the watch is to be provided for use by the back-up
navigator when attending locations not connected to the fixed installation.
13.9 Route Planning

The vessel is to carry official charts sufficient to enable route planning and monitoring for the intended
voyage. However, where the charting function is partially or fully effected via electronic charts, a back-up
means is to be provided. In addition, an alarm is to be given in case of deviation from the planned route,
which is to be adjustable having regard to the time to danger of grounding.
13.10 Vessel’s Automatic Identification System (December 2003)

A vessel’s automatic identification system (AIS) is to be fitted onboard the vessel to provide automatically
to appropriately fitted shore stations, other vessels and aircraft, needed navigational related information
such as vessel’s identity, type, position, course, speed, navigational status, etc., and other safety related
information, and to automatically receive such information from similarly fitted vessels and to monitor and
track vessels and to exchange data with shore based facilities. The automatic identification system (AIS) is
to comply with IMO’s Res. MSC.74(69), Annex 3 “Recommendation on Performance Standards for an
Universal Shipborne Automatic Identification System”.
15 Propulsion Engine/thruster Controls

Means for controlling the propulsion engines/thrusters are to be provided at the wheelhouse and same is to
be at least in compliance with Section 4-9-2 of the Marine Vessel Rules.
17 Automatic Telephone System (December 2003)

The vessel is to be fitted with an automatic telephone system, which is to comply with the following. In
addition, a telephone system that can operate independently of the power supply from the vessel’s main or
emergency system is to be installed.
17.1
The system is to enable two-way communication between all relevant workstations on the bridge and:
● Navigating officer's cabins and public rooms

● Radio room (when located outside the bridge area)
● Steering gear room

● If provided, emergency steering position

● Propulsion-machinery room
17.2
The automatic telephone network is to be designed to carry at least 2 simultaneous calls.
17.3
Telephones on the bridge and propulsion machinery control room are to have priority function over any
other extension. A list of all relevant telephone extensions is to be permanently posted and clearly
displayed adjacent to each telephone.
19 Nautical Radiocommunication System

The vessel is to be fitted with means for nautical radiocommunication with other vessels as well as means
for communication with tugboats and mooring stations aboard and ashore.
21 Workstations - Required Equipment

As a minimum, in addition to alarms/indicators invoked in the various IMO Resolutions referenced in this
Guide, the equipment listed in 3/27 TABLE 1 is to be fitted at the various workstations to enable the
officer of the watch and other operators to carry out the required tasks.
23 Operating/Technical Manual
An operating/technicalmanual which is consistent with the information and criteria upon which the
notation NBLES is based is to be placed onboard the vessel for the guidance of the operating personnel.
The operating/technical manual is to give clear guidance to the vessel's personnel about the vessel's
capability, limitation and procedures to follow when navigating the vessel with the required manning on
the bridge. The operating/technicalmanual is to include the following, as a minimum.
23.1
Vessel’s name and ABS ID number.
23.2
Simplified diagrams of the systems described in 3/11 through 3/19.
23.3
Vessel’s navigating and maneuvering capabilities (i.e., particulars of propulsion machinery and steering
system, vessel’s speed, vessel’s stopping ability, vessel’s turning ability, etc.).
23.4
Navigational procedures including transfer of alarms to the back-up navigator, and details of the routines,
duties and responsibilities of each of the relevant personnel associated with the bridge operation of the
vessel.
23.5
Periodical testing procedures for relevant navigational equipment/systems.
The operating/technical manual is to be submitted to ABS for reviewsolely to ensure the presence of the
above information which is to be consistent with the vessel's design information and navigational
capabilities. The operation of the vessel is not a condition of the assigned class notations.

Any modifications made to the approved bridge layout, field of views and navigational equipment/systems
are to be approved by ABS. The operating/technical manual is to be updated accordingly, and submitted to
ABS for review.
25 Tests and Sea Trials

During sea trials, navigational equipment and systems are to be tested to the satisfaction of the attending
Surveyor in accordance with a test program. The test program is to include the following test details:
25.1 Applicable to All Relevant Navigational Equipment

25.1.1
Prior to testing, all relevant navigational equipment/systems are to be satisfactorily checked,
calibrated and operated by the representative of the manufacturer or the equipment supplier who is
to issue an affidavit to such effect for the review of the attending Surveyor.
Automatic resumption of primary bridge navigational equipment/systems functions are to be demonstrated

following a blackout simulation of a period of 45 seconds. Similarly, resumption of all other relevant non-
primary bridge navigational equipment/systems functions are to be satisfactorily effected following a
blackout simulation period of five minutes. See 3/11.3.
25.2 Specific Equipment or System

Test details for the following equipment or systems:
a) Course information system.

b) Automatic steering system.
c) Speed measuring system.
d) Depth measuring system.
e) Radar system.
f) Automatic traffic surveillance system
g) Position-fixing system.
h) Watch monitoring and alarm transfer system.
i) Route planning system.
j) Vessel's automatic identification system.
k) Automatic Telephone System.
l) Sound reception in bridge, if fitted.
m) Radiocommunication system.
27 Survey After Construction

The following items are to be satisfactorily examined or verified at each Annual Survey of the vessel.
27.1
Ready availability of the approved operating/technical manual. See 3/23.
27.2
Required bridge’s fields of vision. See 2/5.1.

27.3
The systems described in 3/13 through 3/19. Additionally, subject to the discretion of the attending
Surveyor, such systems may be tested in accordance with 3/25.
27.4
Following a loss of power supply, resumption of same to navigational equipment. See 3/11.3.

TABLE 1
Navigational Equipment for NBLES Notation (1 May 2019)
Workstation for Main functions to be performed Item Equipment Remarks
Navigation and ● Observation of all vessels and A1 Gyro compass heading (December 2003) For NIBS
Traffic objects indicator notation, two independent
Surveillance/ gyro compasses are to be
maneuvering ● Recognizing dangerous provided on the bridge (See
[See Note 1] situations 4/13.1). See note 2.
● Deciding on collision A2 Magnetic compass heading
avoidance actions indicator
● Checking vessel's own signal A3 Course reminder (set
● Checking own course and course) indicator
speed A4 Rudder pump selector
● Keeping and/or changing own switch
course and speed (track
A5 Steering mode selector
keeping)
switch
● Checking own position
A6 Steering position indicator
● Handling own internal
A7 Rudder angle indicator
communication on board
A8 Pitch indicator For controllable-pitch
● Handling communication
propeller
vessel/ vessel, and vessel/
shore (VHF) A9 Rate-of-turn indicator and For vessels 50,000 GT or
● controller greater. See 3/13.2.4 and
Releasing alarms
3/13.2.5
● Perception of group alarms
A10 Speed and distance For NIBS notation, the speed
with aids for decision-making
indicator measuring system is to be
● Observation of weather and independent of the position-
seaway fixing systems. See 4/13.2
● Acknowledging watch check- A11 Depth water indicators with See also 3/13.4
alertness alarm adjustment controls
● Keeping deck log (a A12 9 GHz radar For vessels 3,000 GT and
dictaphone may be used) above, an additional
● Sounding signals independent radar together
with a change-over switch is
to be provided. See 3/13.5.2
A13 Automatic traffic See 3/13.6. For NIBS

surveillance system notation, see 4/13.3
including ARPA
A14 Position fixing equipment/ Two types of receivers are to

system including automatic be provided. One of the
visual position indicator systems is to be GPS or
equivalent, and the other:
Decca, Loran-C, GLONASS,
or other means. See 3/13.7
A15 Officer of the watch check-

alertness acknowledgment
device

A16 Back-up navigator call Two-way communication

alarm device wireless portable device to
be provided. See 3/13.8.2.b
A17 Facilities for use of This may be separated from

navigation charts the navigation and traffic
surveillance/maneuvering
workstation. See also 3/13.10
A18 Vessel's automatic

identification system
A19 Propulsion engines/ Compliance with 4-9-2 of

thrusters controls including the Marine Vessel Rules is to
emergency stops. be met
A20 Propulsion engine If reduction geared engine

revolution
A21 Propeller revolutions

indicator
A22 Wind direction and velocity

indicator
A23 Air and water temperature

indicator
A24 Automatic telephone See 3/17

system
A25 Radiocommunication See 3/19

equipment
A26 NAVTEX automatic For navigational and

receiver and recorder meteorological warning
purpose. To comply with
IMO Res. A.617(15) -
"Implementation of the
Navtex System as a
Component of the
Worldwide Navigational
Warning Service"
A27 Signal transmitter for:

● whistle
● automatic device for
fog signal
● general alarm
● Morse signaling light
A28 Search light controls e.g., searchlight on/off

switch
A29 Controls for windscreen

wiper, washer, heater
A30 Night vision equipment

A31 Sound reception system (December 2003) If required,

see 2/5.6.3
A32 Workstation lighting control

device
A33 HVAC controls
A34 Clock
A35 Group alarms and reset (December 2003) See also

controls item B17 of this Table

Monitoring ● Observation of all vessels and B1 Gyro compass heading (December 2003) For NIBS
[See Note 1] objects indicator notation, two independent
gyro compasses are to be
● Recognizing dangerous provided on the bridge (See
situations 4/13.1). See note 2.
● Handling own internal B2 Rudder angle indicator
communication on board
B3 Pitch indicator For controllable-pitch
● Handling communication propeller
vessel/ vessel, and vessel/
shore B4 Rate-of-turn indicator For vessels 50,000 GT or
greater. See 3/13.2.4 and
● Perception of group alarms 3/13.2.5
with aids for decision-making
B5 Speed and distance For NIBS notation, the speed
● Releasing alarms
indicator measuring system is to be
● Observation of weather and independent of the position-
seaway fixing systems. See 3/13.2
● Acknowledging watch check- B6 Depth water indicators See also 3/13.4

alertness alarm
B7 Radar For vessels 3,000 GT and
● Keeping deck log above, an additional
independent radar together
● When workstation is occupied
with a change-over switch is
by an additional navigator,
to be provided. See 3/13.5.2
provides assistance to
navigator at the navigation B8 Officer of the watch check-
and traffic surveillance/ alertness acknowledgment
maneuvering workstation device
● When workstation is occupied B9 Propulsion engines/
by a pilot, advises to vessel's thrusters emergency stops
command.
B10 Propeller revolutions
indicator
B11 Automatic telephone See 3/17

system
B12 Radiocommunication See 3/19

equipment
B13 Signal transmitter for

whistle
B14 Controls for windscreen

B15 Workstation lighting control

device
B16 Clock

B17 Required alarms and reset (December 2003) In addition

controls to the alarms/indicators
which may be required by
the various IMO Resolutions
referenced in this Guide and
pertinent flag
Administration, the
following conditions are to
be alarmed at the monitoring
workstation
a) Off-heading
b) Off-track
c) Planned route deviation
d) Pre-warning of approach-
waypoint , and closest point
of approach
e) Off-preset water depth
f) Gyro compass failure
g) Failure of alarms
prescribed in 3/13.8.1
h) Failure of power supply to
distribution panel serving
relevant equipment
(Alarming of the above
conditions at the monitoring
workstation is not a
substitute for alarming at the
required relevant
workstations)

Manual ● Steering vessel according to C1 Gyro compass heading (December 2003) For NIBS
steering rudder angle orders indicator (repeater) notation, two independent
(Helmsman's) gyro compasses are to be
[See Note 1] ● Steering vessel according to provided on the bridge (See
course instruction 4/13.1). See note 2.
● Steering vessel following C2 Magnetic compass heading
landmark/ sea marks indicator
● Acknowledging watch check- C3 Course reminder (set
alertness alarm course) indicator
C4 Manual steering with

override and selector
control switches including
steering wheel/steering
lever
C5 Rudder angle indicator
C6 Rate-of-turn indicator For vessels 50,000 GT or

greater
C7 Watch check-alertness
acknowledgment device
C8 Automatic telephone See 3/17

system
C9 Controls for windscreen

Notes:
1 As the navigation and traffic surveillance/maneuvering, monitoring and manual steering workstations
are functionally interrelated and usually installed in close proximity from each other, considerations will
be given to the omission of duplicate required equipment at each of the aforementioned workstations.
2 (December 2003) Master gyrocompass may be located in the electrical/instrumentation room and the
gyrocompass repeaters on the bridge to meet this requirement.

TABLE 2
Navigational Equipment for NBLES+ Notation (1 May 2019)
Docking ● Giving instructions, D1 Gyro compass heading (December 2003) For NIBS
(Bridge wings) performing and controlling indicator notation, two independent
change of course gyro compasses are to be
provided on the bridge (See
● Giving instructions, 4/13.1). See note 1.
performing and controlling
change of speed D2 Steering position selector
switch
● Giving instructions,
performing and controlling D3 Rudder controls
change of thruster D4 Rudder angle indicator
● Handling communication with
D5 Pitch indicator For controllable-pitch
maneuvering stations
propeller
● Handling communication with
D6 Rate-of-turn indicator For vessels 50,000 GT or
tugs, pilot boat
greater
● Watching water surface along
D7 Propulsion engines/
vessel's side
thrusters controls.
● Releasing signals
D8 Propulsion engine If reduction geared engine
● Acknowledging watch check- revolution
alertness alarm
D9 Propeller revolutions
indicator
D10 Lateral thrust and lateral If thrusters are fitted

movement of vessel,
indicator
D11 Longitudinal movement of

vessel, indicator
D12 Wind direction and velocity

indicator
D13 Depth water indicators See also 3/13.4
D14 Officer of the watch check-

alertness acknowledgment
device
D15 Whistle controls
D16 Search light and Morse

lamp controls
D17 Automatic telephone See 3/17

system
D18 Radio communication See 3/19

equipment
D19 Workstation lighting control

device

Notes:
1 (December 2003) Master gyrocompass may be located in the electrical/instrumentation room and the
gyrocompass repeaters on the bridge to meet this requirement.

SECTION 4 Requirements for Notation NIBS (Navigational
Integrated Bridge System)
1 General
The following requirements are applicable to vessel which is fitted with the navigational equipment/
systems, as required in this Guide, so arranged to form an integrated bridge system (IBS). Vessels
complying with Sections 1 through 4 of this Guide, will be assigned the notation NIBS (Navigational
Integrated Bridge System). Equipment required for this notation is listed in 4/21 TABLE 1.
3 Integrated Bridge System (IBS)

An integrated bridge system (IBS) is to be provided and is to comply with IMO SN.1/Circ.288 –
Guidelines for Bridge Equipment and Systems, Their Arrangement and Integration (BES). For the purpose
of this Guide, the integrated bridge system pertains only to aspects dealing with navigational, monitoring/
alarming and communication functions as covered in this Guide. The integrated navigation system is to be
so arranged that failure of one sub-system does not affect any other sub-system. In case of failure of the
integrated navigation system it is to be possible to operate the primary bridge navigational equipment/
systems functions separately.
3.1 Dimmer Control (1 May 2018)

An individual dimmer control is acceptable in lieu of a single central dimming functionality called for by
the Guidelines (IMO SN.1/Circ.288) provided the number of the individual dimmer control switches is
minimized as far as practicable.
5 Centralized Bridge Workstation

A centralized bridge workstation is to be provided to enable the navigator to perform the necessary
navigational, monitoring/alarming and communication functions as required in this Guide. The equipment
required in the navigation and traffic surveillance/maneuvering workstation and monitoring workstation,
specified in Section 3 of this Guide, is to be integrated within the centralized bridge workstation. See also
4/21 TABLE 1 for the required equipment to be included on this workstation.
7 Central Alarm Panel

The centralized bridge workstation is to be fitted with a central alarm panel for instruments and systems
related to the functions specified in D3 for easy identification and acknowledgment of the individual
alarms. Acknowledgment of an alarm at either the equipment fitted on the required workstation or the
central alarm panel is to cancel the audible warning at both sources. Cancellation of the visual warning on
the central alarm panel is to only be possible at the pertinent workstation.
In addition to required navigational alarms and those alarm conditions listed in the "Remark" column to
item B17, a through h, of 3/27 TABLE 1, the following alarm conditions are to be alarmed at the central
alarm panel:
● Position fixing inaccurate/lost.

● Loss of heading input.
● Loss of log input.
● Gyro compass mis-match.

Section 4 Requirements for Notation NIBS (Navigational Integrated Bridge System) 4
● Integrated bridge system (IBS) failure.
9 Route Planning Workstation

The route planning workstation is to enable the navigator to plan the intended voyage without interfering
with the actual navigation or maneuvering of the vessel. It is to be large enough to facilitate the use of two
charts concurrently, and adequately fitted for efficient route planning. See 4/21 TABLE 1 for the required
equipment to be included on this workstation.
11 Conning Information Display

A conning information display is to be provided on the bridge and which is to be observable from the
conning position(s) and designed for easy reading of the maneuvering state of the vessel. The information
on continuous display is to be restricted to information relevant to the actual phase of the voyage. This
display may be included on the centralized bridge workstation. See also 2/5.2.2.
13 Navigational System Requirements

Requirements contained herein are in addition to or modified those in 3/13.
13.1 Course Information System (December 2003)

Notwithstanding 3/13.1, the heading information system is to include a magnetic compass and two
independent gyro compasses.
13.2 Speed Measuring System

In addition to 3/13.3, the speed measuring system is to be independent of the position-fixing systems.
13.3 Automatic Track-keeping System

In addition to 3/13.6, the automatic track-keeping system is to automatically enable the vessel to keep
along a pre-planned track and the vessel’s position is to be monitored continuously. When the vessel’s
position cannot be received, the current heading or rate of turn is to be maintained until manually altered
by the officer of the watch, and such condition is to be alarmed. The vessel’s position is to be cross-
checked by dead-reckoning based upon speed over ground provided by the vessel’s log.
13.4 Electronic Chart Display and Information System (ECDIS) (December 2003)
Relevant equipment associated with the ECDIS (Electronic Chart Display and Information System) is to be
installed on the centralized bridge workstation and at the route planning workstation. The ECDIS is to
comply with IMO’s Res. A.817(XIX), as amended by Annex 5 to MSC.64(67) "Performance Standard for
Electronic Chart Display and Information Systems (ECDIS)", and Annex 4 to MSC.86 (70) "Performance
Standard for Electronic Chart Display and Information Systems (ECDIS)" .
15 Operating/Technical Manual
In addition to 3/23, the operating/technical manual is to include the following:
15.1 (December 2003) Simplified diagrams of the electronic chart display and information systems
(EDCIS) and integrated bridge system (IBS).
15.2 (December 2003) Periodical testing procedures for electronic chart display and information systems
17 Workstations - Required Equipment

In addition to 3/21, the equipment listed in 4/21 TABLE 1 is to be fitted on the bridge.

19 Tests and Sea Trials (December 2003)

The sea trial program is to include test details of the electronic chart display and information systems
21 Survey After Construction

In addition to 3/27, the systems described in 4/3 and 4/13 are to be included.
TABLE 1
Navigational Equipment for NIBS Notation (December 2003)
Workstation/ Main functions to be performed Ite Equipment Remarks

panel for m
Centralized ● See 3/27 TABLE 1 A1 Equipment required in Part C See 3/27 TABLE 1
Bridge for the Navigation and
Traffic Surveillance/
maneuvering and monitoring
workstations
A2 Central alarm panel See 4/7
A3 ECDIS See 4/13.4
Conning ● To allow the navigator the B1 Display panel See 4/11. This panel may be
Information easy reading of the included within the
maneuvering state of the centralized bridge station.
vessel from the conning
position
Manual ● See 3/27 TABLE 1 C1 Equipment required in Part C See 3/27 TABLE 1
steering for the manual steering
(Helmsman's) workstation
Docking ● See 3/27 TABLE 1 D1 Equipment required in Part C See 3/27 TABLE 1
(Bridge wings) for the docking workstation

Workstation/ Main functions to be performed Ite Equipment Remarks

panel for m
Route Planning ● Determination of favorable E1 ECDIS including navigation

course and optimum speed, planning station
taking into account weather E2 Route planning devices
conditions, current, etc. and
route planning E3 Chart table
● Giving instructions as to the E4 Position-fixing receiver

course and speed
E5 Retaining device for drawing
● Calculation of tidal data triangles, dividers,
magnifying lens, pencils, etc.
● Handling nautical records,
documents, publications E6 Weather chart plotter
● Handling weather reports E7 Main clock
● Determination of E8 Chronometer with receiving (December 2003) See Note 2
documentation of position in facility for time signals
case of conventional operation
E9 Radio direction finder (December 2003) See Note 3
● Control of rate and error of
chronometer, deviation, radio E10 Log, including distance
indicator, course plotter
deviation, documentation of
same E11 Officer of the watch check-
● Keeping deck log alertness acknowledgment
device
● External communication for
planning operation using the E12 Barograph
chart E13 Command printer
E14 Automatic telephone system See 3/19
Note:
1 Attention is drawn to items A1, B1, B5, C1 and D1 of 3/27 TABLE 1 under "Remarks" column.
2 (December 2003) Chronometer is not required, if official universal time is obtained by other means.
3 (December 2003) Radio Direction Finder is not required, if the vessel is provided with other radionavigation
equipment suitable for use throughout its intended voyages

APPENDIX 1 IMO Resolutions Referenced in this Guide
(December 2003)
IMO Res. Recommendation on Performance Standards for Echo-sounding Equipment

MSC.74(69), Annex 4
IMO Res. Recommendation on Performance Standards for Automatic Pilots

MSC.64(67), Annex 3
IMO Res. A.342(IX) Recommendation on Performance Standards for Automatic Pilots [see also Res. MSC.64(17)]
IMO Res. A.382(X) Magnetic Compasses Carriage and Performance Standards
IMO Res. A.384(X) Performance Standards for Radar Reflector
IMO Res. A.424(XI) Performance Standards for Gyro-compasses
IMO Res. A.477(XII) Performance Standards for radar Equipment [see also Res. MSC.64(67), Annex 4]
IMO Res. A.526(13) Performance Standards for Rate-of-Turn Indicators
IMO Res. A.617(15) Implementation of the Navtex System as a Component of the Worldwide Navigational Warning
Service
IMO Res. A.665(16) Performance Standards for Radio Direction-finding Systems [revokes Res. A223 (VII)]
IMO Res. A.694(17) General Requirements for Shipborne Radio Equipment Forming Part of the Global Maritime
Distress and Safety System (GMDSS) and for Electronic Navigational Aids [revokes Res.
A574(14)]
IMO Res. A.816(19) Recommendation on Performance Standards for Shipborne Decca Navigator Receivers
IMO Res. A.817(19) Recommendation on Performance Standards for Electronic Chart Display and Information System
(ECDIS) [see also Res. MSC.64(67), Annex 5]
IMO Res. A.818(19) Performance Standards for Shipborne Loran-C and Chayka Receivers
IMO Res. A.823(19) Recommendation on Performance Standards for Automatic Radar Plotting Aids (Arpas) [for
installations before 1/1/97, see Res. A.422(IX)]
IMO Res. Performance Standards for Automatic Identification System

MSC.74(69), Annex 3
IMO Res. Recommendation on Performance Standards for Track Control Systems

MSC.74(69), Annex 2
IMO Res. Recommendation on Performance Standards for Heading Control Systems

MSC.64(67), Annex 3
IMO Res. MSC.96(72) Performance Standards for Devices to indicate Speed and Distance [for installations before
1/1/97, see Res. A.478(XII)]
IMO Res. Performance Standards for Shipborne GLONASS receiver Equipment

MSC.113(73)
IMO Res. Performance Standards for Devices to Measure and Indicate Speed and Distance
MSC.96(72), Annex
14

Appendix 1 IMO Resolutions Referenced in this Guide (December 2003) A1
MSC. Circular 53(66) Performance Standards for Shipborne GLONASS receiver Equipment
MSC. Circular 64(67) Adoption of New an Amended Performance Standards [revokes Res. A.574; amends Res.
A342(IX), Res. A477(XII) and Res. A.817(19)]

Bridge Design Guide May 2019

Uploaded by

Copyright:

Available Formats

Bridge Design Guide May 2019

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bridge Design Guide May 2019

Uploaded by

Copyright:

Available Formats

GUIDE FOR

BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/

American Bureau of Shipping

© 2019 American Bureau of Shipping. All rights reserved.

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 ii

SECTION 2 Requirements for Notation NBL (Navigation Bridge Layout)........ 13

SECTION 3 Requirements for Notation NBLES (Navigational Bridge

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 iv

TABLE 1 Navigational Equipment for NBLES Notation.......................28

SECTION 4 Requirements for Notation NIBS (Navigational Integrated

TABLE 1 Navigational Equipment for NIBS Notation (December

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 v

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 vi

5.1 Notation NBL (Navigational Bridge Layout)

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 7

5.3 Notation NIBS (Navigational Integrated Bridge System)

9 Flag Administration and National Authorities

11 Definitions (December 2003)

Alarm - A visual and audible signal indicating an abnormal condition.

ARPA - Automatic Radar Plotting Aid.

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 8

GLONASS - Global Orbiting Navigating Satellite Systems.

GMDSS - Global Maritime Distress and Safety System.

Helmsman - Person who steers the vessel.

Main Workstation - See “navigation and traffic surveillance/maneuvering workstation”.

Navigation and Traffic Surveillance/maneuvering Workstation - Main workstation at which the

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 9

Operating/Technical Manual – Manuals or operational instructions for equipment/systems installed on

TCPA - Time to Closest Point of Approach.

Way-point - Any of various intermediate points on a route.

Wheelhouse - Enclosed area of the bridge.

13 Plans and Data to be Submitted

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 10

13.2 Applicable to NBLES, NBLES+ and NIBS Notations (1 May 2019)

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 11

13.3 Applicable to NIBS Notation

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 12

3 Equipment Design and Construction

3.1 General (December 2003)

3.2 Fault Isolation

3.3 Replacement of Components

3.5 Configuration of Devices

3.6 Instruments and Controls

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 13

3.6.1 Digital Readout

3.6.2 Circular Scale

3.6.3 Linear Scale

3.6.5 Mechanical Control

3.6.6 Light Contrast

3.6.7 Illumination and Lighting

5 Bridge Arrangement and Working Environment

5.1 Fields of Vision

5.2 Control of Vessel

ABS GUIDE FOR BRIDGE DESIGN AND NAVIGATIONAL EQUIPMENT/SYSTEMS • 2019 14

5.2.2 Conning Position (December 2003)

5.2.3 Navigation and Traffic Surveillance/Maneuvering Workstation

5.2.4 Route Planning Workstation

5.2.5 Monitoring Workstation

5.2.6 Manual Steering Workstation

5.2.7 Docking Workstations