Single Bus System
Single Bus System
Single Bus System
Search
Electrical Power Transmission System There are many different electrical bus system schemes available but selection of a particular
Performance of Transmission Line scheme depends upon the system voltage, position of substation in electrical power system,
ABCD Parameters of Transmission Line flexibility needed in system and cost to be expensed.
Electrical Substation (v) Optimizing the selection of bus bar arrangement scheme so that it gives maximum return from
the system.
Mobile Substation
Electrical Bus System & Substation Layout
Some very commonly used bus bar arrangement are discussed below-
Electrical Insulator
Types of Electrical Insulator
Insulation Coordination Single Bus System
Insulator Testing
Electrical Isolator or Isolation Switch Single Bus System is simplest and cheapest one. In this scheme all the feeders and transformer bay
Transmission Tower are connected to only one single bus as show.
Some advantages are realized if a single bus bar is sectionalized with circuit breaker. If there are more than one incoming and the incoming sources and
outgoing feeders are evenly distributed on the sections as shown in the figure, interruption of system can be reduced to a good extent.
If any of the sources is out of system, still all loads can be fed by switching on the sectional circuit breaker or bus coupler breaker. If one section of the bus
bar system is under maintenance, part load of the substation can be fed by energizing the other section of bus bar.
1) As in the case of single bus system, maintenance of equipment of any bay cannot be possible
without interrupting the feeder or transformer connected to that bay.
2) The use of isolator for bus sectionalizing does not fulfill the purpose. The isolators have to be
operated ‘off circuit’ and which is not possible without total interruption of bus – bar. So
investment for bus-coupler breaker is required.
1) In double bus bar system two identical bus bars are used in such a way that any
outgoing or incoming feeder can be taken from any of the bus.
2)Actually every feeder is connected to both of the buses in parallel through individual isolator as shown in the figure.
By closing any of the isolators one can put the feeder to associated bus. Both of the buses are energized and total feeders are divided into two groups, one
group is fed from one bus and other from other bus. But any feeder at any time can be
transferred from one bus to other. There is one bus coupler breaker which should be kept close
during bus transfer operation. For transfer operation, one should first close the bus coupler
circuit breaker then close the isolator associated with the bus to where the feeder would be
transferred and then open the isolator associated with the bus from where feeder is transferred.
Lastly after this transfer operation he or she should open the bus coupler breaker.
The arrangement does not permit breaker maintenance with out interruption.
In double breaker bus bar system two identical bus bars are used in such a way that any outgoing or incoming feeder can be taken from any of the
bus similar to double bus bar system. Only difference is that here every feeder is connected to both of the buses in parallel through individual breaker instead
only isolator as shown in the figure. By closing any of the breakers and its associated isolators, one can put the feeder to respective bus. Both of the buses are
energized and total feeders are divided into two groups, one group is fed from one bus and other from other bus similar to previous case. But any feeder at any
time can be transferred from one bus to other. There is no need of bus coupler as because the operation is done by breakers instead of isolator. For transfer
operation, one should first close the isolators and then the breaker associated with the bus to where the feeder would be transferred and then he or she opens
the breaker and then isolators associated with the bus from where feeder is transferred.
This is an improvement on the double breaker scheme to effect saving in the number
of circuit breakers . For every two circuits only one spare breaker is provided. The
protection is however complicated since it must associate the central breaker with the feeder
whose own breaker is taken out for maintenance. For the reasons given under double breaker
scheme and because of the prohibitory costs of equipment even this scheme is not much
popular. As shown in the figure that it is a simple design, two feeders are fed from two different
buses through their associated breakers and these two feeders are coupled by a third breaker
which is called tie breaker. Normally all the three breakers are closed and power is fed to both the
circuits from two buses which are operated in parallel. The tie breaker acts as coupler for the two
feeder circuits.
During failure of any feeder breaker, the power is fed through the breaker of the second feeder and tie breaker, therefore each feeder breaker has to be rated to
feed both the feeders, coupled by tie breaker.
During any fault on any one of the buses, that faulty bus will be cleared instantly without
interrupting any feeders in the system since all feeders will continue to feed from other healthy
bus.
(i) First close the isolators at both side of the bus coupler breaker.
(ii) Then close the bypass isolator of the feeder which is to be transferred to transfer bus.
(iii) Now energized the transfer bus by closing the bus coupler circuit breaker from remote.
(iv) After bus coupler breaker is closed, now the power from main bus flows to the feeder line through its main
breaker as well as bus coupler breaker via transfer bus.
(v) Now if main breaker of the feeder is switched off, total power flow will instantaneously shift to the bus coupler breaker and hence this breaker will serve the
purpose of protection for the feeder.
(vi) At last the operating personnel open the isolators at both sides of the main circuit breaker to make it isolated from rest of the live system.
So it can be concluded that in Main & Transfer Bus System the maintenance of circuit breaker is possible without any interruption of power. Because of this
advantage the scheme is very popular for 33KV and 13KV system.
This is combination of the double bus system and main and transfer bus system. In Double Bus
System with Bypass Isolators either bus can act as main bus and second bus as transfer bus. It
permits breaker maintenance without interruption of power which is not possible in double bus
system but it provides all the advantages of double bus system. It however requires one
additional isolator (bypass isolator) for each feeder circuit and introduces slight complication in
system layout. Still this scheme is best for optimum economy of system and it is best optimum
choice for 220KV system.
The schematic diagram of the system is given in the figure. It provides a double feed
to each feeder circuit, opening one breaker under maintenance or otherwise does not affect
supply to any feeder. But this system has two major disadvantages. One as it is closed circuit
system it is next to impossible to extend in future and hence it is unsuitable for developing system. Secondly, during maintenance or any other reason if any
one of the circuit breaker in ring loop is switch of reliability of system becomes very poor as because closed loop becomes opened. Since, at that moment for
any tripping of any breaker in the open loop causes interruption in all the feeders between tripped breaker and open end of the loop.
Search