Anexo Ii

Totally Integrated 7SL87 - LINEA A VILLA HAYES
Automation Portal
Settings
Device settings
Settings Value
Edit mode primary
Number settings groups 1
Activat. of settings group settings group 1
DIGSI 5 uses following IP address 172.16.60.60 (Integrated Ethernet interface)
Operation-panel language English (United States)
Binary input channel threshold Low: 44 V, High: 88 V
Used time stamp in GOOSE subscriptions On message reception
Hide settings in IEC 61850 structure Hide all settings
Hide SIPROTEC extensions in IEC 61850 structure Hide all SIPROTEC extensions
Use dynamic reporting True
Block IEC 61850 settings changes False
Access point used in Edition1 No access point is specified for the SCD import.
General \Device
Number Settings Value
91.101 Rated frequency All: 50 Hz
91.102 Minimum operate time All: 0 s
91.115 Set. format residu. comp. All: Kr, Kx
91.138 Block monitoring dir. All: off
General \Setting change

91.163 Reserv.time for com.prot. All: 120 s
General \Chatter blocking

91.123 No. permis.state changes All: 0
91.127 Initial test time All: 1 s
91.124 No. of chatter tests All: 0
91.125 Chatter idle time All: 1 min
91.137 Subsequent test time All: 2 s
General \Measurements
91.162 Blk setting change All: false
91.163 Reserv.time for com.prot. All: 120 s
91.111 Energy restore interval Settings group 1: 10 min
91.112 Energy restore time Settings group 1: none
General \Control
91.120 Energy restore Settings group 1: latest value
91.121 Energy restore by A.time All: false
91.118 Enable sw.auth. station All: false
1 of 23
Automation Portal
General \Spontan.indic.
91.119 Multiple sw.auth. levels All: false
General \CFC
91.152 Specific sw. authorities All: false
General \Test support

91.139 Fault-display All: with pickup
91.161 CFC chart quality handling All: automatic
Localization
6211.139 Unit system All: SI
Time settings
General
Settings Value
Date format All: DD.MM.YYYY
Time source
Settings Value
Fault indication after All: 600 s
Time source 1 none
Time source 2 none
Time zone time source 1 All: local
Sync. latency time src.1 All: 0 μs
Time zone and daylight saving time

Settings Value
Time zone offset to UTC All: 60 min
Offset daylight sav. time All: 60 min
Switch daylight sav. time true
Start of daylight sav. time Last Sunday in March at 2:00 AM
End of daylight sav. time Last Sunday in October at 3:00 AM
Power system \General

General
11.2311.101 Phase sequence All: ABC
2 of 23
Automation Portal
Power system \Tensión derv.AB

VT 3-phase
11.941.8911.101 Rated primary voltage All: 500.000 kV
11.941.8911.102 Rated secondary voltage All: 115 V
11.941.8911.104 VT connection All: 3 ph-to-gnd voltages
11.941.8911.106 Inverted phases All: none
11.941.8911.111 Tracking All: active
11.941.8911.130 Measuring-point ID All: 1
VT 1
11.941.3811.103 Magnitude correction All: 1
11.941.3811.108 Phase All: V A
VT 2
11.941.3812.108 Phase All: V B
VT 3
11.941.3813.108 Phase All: V C
Supv. balan. V
11.941.2521.1 Mode Settings group 1: on
11.941.2521.101 Release threshold Settings group 1: 250 kV
11.941.2521.102 Threshold min/max Settings group 1: 0.75
11.941.2521.6 Delay supervision alarm Settings group 1: 5 s
Supv. ph.seq.V
Supv. sum V
11.941.2461.1 Mode Settings group 1: off
11.941.2461.3 Threshold Settings group 1: 125 kV
3 of 23
Automation Portal
VT miniatureCB
11.941.2641.101 Response time Settings group 1: 0 s
Power system \Barra

General
11.961.2311.103 Tracking All: inactive
VT 1
11.961.3811.108 Phase All: V B
VT miniatureCB
Power system \Meas.point I-3ph 1

CT 3-phase \General
11.931.8881.115 CT connection All: 3-phase + IN
CT 3-phase \CT phases

11.931.8881.101 Rated primary current All: 2000 A
11.931.8881.102 Rated secondary current All: 1 A
11.931.8881.117 Current range All: 100 x IR
11.931.8881.118 Internal CT type All: CT protection
11.931.8881.116 Neutr.point in dir.of ref.obj All: yes
11.931.8881.107 CT error changeover All: 1.5
11.931.8881.108 CT error A All: 3 %
11.931.8881.109 CT error B All: 10 %
CT 1
11.931.3841.117 Phase All: I A
4 of 23
Automation Portal
CT 2
11.931.3842.117 Phase All: I B
CT 3
11.931.3843.117 Phase All: I C
CT 4
11.931.3844.117 Phase All: IN
Brk.wire det.
11.931.5581.101 Mode of blocking Settings group 1: blocking
11.931.5581.102 Delta value for autoblock Settings group 1: 1
Supv. balan. I
11.931.2491.101 Release threshold Settings group 1: 1000 A
Supv. ph.seq.I
Supv. sum I
11.931.2431.102 Threshold Settings group 1: 200 A
11.931.2431.101 Slope factor Settings group 1: 0.1
Supv.ADC sum I
5 of 23
Automation Portal
Saturat. det.
11.931.17731.101 CT saturation threshold Settings group 1: 16000 A
Recording \Fault recorder

Control
51.791.2761.130 Fault recording All: with pickup & AR cyc.
51.791.2761.131 Storage All: always
51.791.2761.111 Maximum record time All: 5 s
51.791.2761.112 Pre-trigger time All: 0.5 s
51.791.2761.113 Post-trigger time All: 0.5 s
51.791.2761.116 Manual record time All: 0.5 s
51.791.2761.140 Sampling frequency All: 2 kHz
51.791.2761.141 Sampl. freq. IEC61850 rec. All: 1 kHz
51.791.2761.128 Scaling COMTRADE All: Secondary values
Line 1 \General
General \Rated values
21.9001.101 Rated current All: 1923 A
21.9001.102 Rated voltage All: 500 kV
21.9001.103 Rated apparent power All: 1665.4 MVA
General \Line data

21.9001.149 Neutral point Settings group 1: grounded
21.9001.112 C1 per length unit Settings group 1: 0.014 μF/km
21.9001.113 X per length unit Settings group 1: 0.267 Ω/km
21.9001.114 Line length Settings group 1: 333 km
21.9001.108 Line angle Settings group 1: 84.43 °
21.9001.104 Kr Settings group 1: 3.45
21.9001.105 Kx Settings group 1: 0.74
21.9001.119 CT saturation detection All: no
21.9001.111 Series compensation Settings group 1: no
21.9001.110 Series capacit. reactance Settings group 1: 0 Ω
21.9001.158 P, Q sign Settings group 1: not reversed
Line 1 \Process monitor

Closure detec.
21.1131.4681.101 Operating mode Settings group 1: Manual close only
21.1131.4681.102 Action time after closure Settings group 1: 0.05 s
21.1131.4681.103 Min. time feeder open Settings group 1: 0.25 s
6 of 23
Automation Portal
1pol.open det.
21.1131.4711.101 Operating mode Settings group 1: with measurement
Volt.criterion
21.1131.4801.101 Threshold U open Settings group 1: 120.00 kV
Line 1 \68 P.swing blk

68 P.swing blk
21.5311.1 Mode Settings group 1: on
21.5311.103 Max. blocking time Settings group 1: oo s
68 P.swing blk \Zones to be blocked

21.5311.102 21 Distance prot. 1.Z 1 true
21.5311.102 21 Distance prot. 1.Z 1B true
Line 1 \Fault locator

Fault locator
21.8671.101 Start Settings group 1: with going pickup
21.8671.103 Load compensation Settings group 1: no
Line 1 \Mes.v.fail.det
Mes.v.fail.det
21.2671.115 Asym.fail.-DO on netw.flt. Settings group 1: no
21.2671.113 Asym.fail. - time delay Settings group 1: 10 s
21.2671.102 3ph.fail. - phs.curr.release Settings group 1: 100 A
21.2671.103 3ph.fail. - phs.curr. jump Settings group 1: 100 A
21.2671.101 3ph.fail. - VA,VB,VC < Settings group 1: 20 kV
21.2671.107 Switch-on 3ph. failure All: on
21.2671.106 SO 3ph.fail. - time delay Settings group 1: 3 s
Line 1 \85-21Perm.overr.
85-21Perm.over
7 of 23
Automation Portal

21.1291.5701.101 Send prolongation Settings group 1: 0.05 s
21.1291.5701.102 Send delay Settings group 1: 0 s
21.1291.5701.105 Trans. blk. pickup delay Settings group 1: 0.03 s
21.1291.5701.106 Trans. blk. dropout delay Settings group 1: 0.07 s
21.1291.5701.11 1-pole operate allowed Settings group 1: yes
21.1291.5701.103 Operate delay (1-phase) Settings group 1: 0 s
21.1291.5701.104 Operate delay (multi-ph.) Settings group 1: 0 s
85-21Perm.over \Send with

21.1291.5701.140 21 Distance prot. 1.pickup forward false
21.1291.5701.140 21 Distance prot. 1.Z 1 false
21.1291.5701.140 21 Distance prot. 1.Z 1B true
85-21Perm.over \Operate with

21.1291.5701.141 21 Distance prot. 1.pickup forward false
85-21Perm.over \Trans. block. with

21.1291.5701.142 85-67N Dir. comp..85-67N Dir.com true
Line 1 \85-67N Dir. comp.

85-67N Dir.com
21.1301.5761.101 Send prolongation Settings group 1: 0.05 s
21.1301.5761.102 Send delay Settings group 1: 0 s
21.1301.5761.105 Trans. blk. pickup delay Settings group 1: 0.03 s
21.1301.5761.106 Trans. blk. dropout delay Settings group 1: 0.07 s
21.1301.5761.104 3I0 threshold rev./forw. Settings group 1: 75 %
85-67N Dir.com \Send with

21.1301.5761.140 67N GFP gnd.sys.1.Definite-T 1 false
21.1301.5761.140 67N GFP gnd.sys.1.Inverse-T 1 true
8 of 23
Automation Portal
85-67N Dir.com \Operate with

85-67N Dir.com \Trans. block. with

21.1301.5761.142 85-21Perm.overr..85-21Perm.over true
Line 1 \Switch onto fault 1

Stage 1
21.1341.5941.2 Operate & flt.rec. blocked Settings group 1: no
21.1341.5941.6 Operate delay Settings group 1: 0 s
Stage 1 \Configuration
21.1341.5941.102 50/51 OC-3ph 1p 1.Definite-T 1 false
21.1341.5941.102 50N/51N OC-gnd-A1.Definite-T 1 false
21.1341.5941.102 50 high-speed 1pol 1.Standard 1 true
Line 1 \50/51 OC-3ph 1p 1

General
21.221.2311.101 Emergency mode Settings group 1: no
Definite-T 1 \General
21.221.841.11 1-pole operate allowed Settings group 1: no
21.221.841.26 Dynamic settings All: no
21.221.841.8 Method of measurement Settings group 1: fundamental comp.
21.221.841.4 Dropout ratio Settings group 1: 0.95
21.221.841.102 Pickup delay Settings group 1: 0 s
21.221.841.101 Dropout delay Settings group 1: 0 s
9 of 23
Automation Portal
Line 1 \50N/51N OC-gnd-A1

General
21.211.2311.101 Emergency mode Settings group 1: no
21.211.2311.9 Measured value Settings group 1: IN measured
21.211.751.101 Dropout delay Settings group 1: 0 s
21.211.751.6 Operate delay Settings group 1: 0.3 s
Line 1 \50 high-speed 1pol 1

Standard 1
21.981.3961.101 Activation Settings group 1: on CB closure
Line 1 \67N GFP gnd.sys.1

General
21.1111.2311.114 Polarization with All: V0 + IY or V2 + I2
21.1111.2311.101 Angle forward α Settings group 1: 338 °
21.1111.2311.102 Angle forward β Settings group 1: 122 °
21.1111.2311.103 Min. zero-seq. voltage V0 Settings group 1: 2.61 kV
21.1111.2311.115 Dir.reslt=forw.at V0<min Settings group 1: no
21.1111.2311.104 Min.3I0 f.increas.dir.sens. Settings group 1: 100 A
21.1111.2311.107 Min. neg.-seq. voltage V2 Settings group 1: 2.61 kV
21.1111.2311.106 Min. neg.-seq. current I2 Settings group 1: 100 A
21.1111.2311.116 Dir.corr.at ser.comp.lines Settings group 1: no
21.1111.4861.114 Directional mode Settings group 1: forward
21.1111.4861.8 Method of measurement Settings group 1: 1-cycle filter
21.1111.4861.130 Blocking by prot. pickup Settings group 1: every pickup
21.1111.4861.129 Op.mode at 1p dead time Settings group 1: blocked
10 of 23
Automation Portal

21.1111.4861.112 Hold mode 1p dead time Settings group 1: 0.04 s
21.1111.4861.111 Stabiliz. w. phase current Settings group 1: 10 %
Definite-T 1 \Blocking by
21.1111.4861.140 87 Line diff. prot..Group indicat. true
21.1111.4861.140 87 Stub diff. prot. 1.Group indicat. false
21.1111.4861.140 21 Distance prot. 1.Z 1B false
21.1111.4862.114 Directional mode Settings group 1: non-directional
Definite-T 2 \Blocking by
21.1111.4862.140 87 Line diff. prot..Group indicat. false
Inverse-T 1 \General
21.1111.4891.131 Blocking by prot. pickup Settings group 1: every pickup
11 of 23
Automation Portal

21.1111.4891.133 Type of character. curve Settings group 1: IEC normal inverse
21.1111.4891.106 Time dial Settings group 1: 0.13
21.1111.4891.132 Additional time delay Settings group 1: 0 s
21.1111.4891.134 Reset Settings group 1: instantaneous
Inverse-T 1 \Blocking by
21.1111.4891.140 87 Line diff. prot..Group indicat. true
Line 1 \59 Overvolt.-3ph 1

Definite-T 1
21.51.181.9 Measured value Settings group 1: phase-to-phase
21.51.181.101 Pickup mode Settings group 1: 3 out of 3
Definite-T 2
21.51.182.9 Measured value Settings group 1: phase-to-phase
21.51.182.101 Pickup mode Settings group 1: 1 out of 3
Line 1 \21 Distance prot. 1

General
21.901.2311.110 Zone timer start Settings group 1: on dist. pickup
21.901.2311.107 Dist. characteristic angle Settings group 1: 72 °
21.901.2311.105 Ground-fault detection Settings group 1: 3I0 or V0
21.901.2311.103 3I0> threshold value Settings group 1: 200 A
21.901.2311.102 V0> threshold value Settings group 1: 21.74 kV
21.901.2311.104 3I0 pickup stabilization Settings group 1: 0.1
21.901.2311.108 Loop select. with ph-ph-g Settings group 1: block leading phase
12 of 23
Automation Portal
Pickup Z<
21.901.3661.101 Min. phase-current thresh Settings group 1: 200 A
21.901.3661.102 Use ph-g load cutout All: no
21.901.3661.105 Use ph-ph load cutout All: no
Z1
21.901.3571.121 Blocked if diff.prot.active Settings group 1: yes
21.901.3571.101 Function mode Settings group 1: ph-gnd and ph-ph
21.901.3571.114 Zone-spec. residu. comp. Settings group 1: no
21.901.3571.102 X reach Settings group 1: 75.57 Ω
21.901.3571.103 R (ph-g) Settings group 1: 42 Ω
21.901.3571.104 R (ph-ph) Settings group 1: 42 Ω
21.901.3571.113 Zone-inclination angle Settings group 1: 0 °
21.901.3571.112 Operate delay (multi-ph.) Settings group 1: 0 s
Z2
21.901.3572.121 Blocked if diff.prot.active Settings group 1: no
21.901.3572.110 Operate delay (1-phase) Settings group 1: 0.3 s
21.901.3572.112 Operate delay (multi-ph.) Settings group 1: 0.3 s
Z3
13 of 23
Automation Portal

Z4
21.901.3574.109 Directional mode Settings group 1: reverse
Z 1B
21.901.3575.110 Operate delay (1-phase) Settings group 1: oo s
21.901.3575.112 Operate delay (multi-ph.) Settings group 1: oo s
Line 1 \Weak infeed

Weak infeed
21.1331.5821.101 Echo block time after Tx Settings group 1: 0.05 s
21.1331.5821.102 Echo and operate delay Settings group 1: 0.04 s
21.1331.5821.103 Echo pulse Settings group 1: 0.05 s
21.1331.5821.104 Weak infeed action Settings group 1: only echo
21.1331.5821.105 85-21/67N common chan. Settings group 1: no
21.1331.5821.106 Undervoltage threshold Settings group 1: 108.70 kV
Line 1 \87 Line diff. prot.

General
21.831.2311.102 Min. current for release Settings group 1: 0 A
14 of 23
Automation Portal

21.831.2311.104 Supervision Idiff All: yes: block diff. prot.
I-DIFF
21.831.3451.101 Thresh. switch onto fault Settings group 1: 416 A
I-DIFF fast 2
21.831.18211.101 Thresh. switch onto fault Settings group 1: 2000 A
Ic-compensat.
21.831.3511.101 Ic-stabilization/Ic-rated Settings group 1: 1.5
21.831.3511.102 Total line length Settings group 1: 333 km
21.831.3511.110 Rated charging current Settings group 1: 415 A
Line 1 \87 Stub diff. prot. 1

General
S-DIFF
S-DIFF fast 2
Line 1\Ciruit-breaker interaction

Protection group Circuit-breaker group(s)
Line 1\ 85-21Perm.overr.\ 85-21Perm.over Circuit breaker 1:Start auto.recl., Circuit breaker 1:Trip, Circuit
breaker 2:Start auto.recl., Circuit breaker 2:Trip
15 of 23
Automation Portal

Line 1\ 85-67N Dir. comp.\ 85-67N Dir.com Circuit breaker 1:Start auto.recl., Circuit breaker 1:Trip, Circuit
Line 1\ Switch onto fault 1\ Stage 1 Circuit breaker 1:Blk. auto.recl., Circuit breaker 1:Trip, Circuit
breaker 2:Blk. auto.recl., Circuit breaker 2:Trip
Line 1\ 50/51 OC-3ph 1p 1\ Definite-T 1 Circuit breaker 1:Start auto.recl., Circuit breaker 1:Trip, Circuit
Line 1\ 50N/51N OC-gnd-A1\ Definite-T 1 Circuit breaker 1:Start auto.recl., Circuit breaker 1:Trip, Circuit
Line 1\ 67N GFP gnd.sys.1\ Definite-T 1 Circuit breaker 1:Start auto.recl., Circuit breaker 1:Trip, Circuit
Line 1\ 67N GFP gnd.sys.1\ Definite-T 2 Circuit breaker 1:Start auto.recl., Circuit breaker 1:Trip, Circuit
Line 1\ 67N GFP gnd.sys.1\ Inverse-T 1 Circuit breaker 1:Trip, Circuit breaker 2:Trip
Line 1\ 59 Overvolt.-3ph 1\ Definite-T 2 Circuit breaker 1:Trip, Circuit breaker 2:Trip
Line 1\ 87 Line diff. prot.\ General Circuit breaker 1:Start auto.recl., Circuit breaker 1:Trip, Circuit
Line 1\ 87 Stub diff. prot. 1\ General Circuit breaker 1:Trip, Circuit breaker 2:Trip
Line 1\ 21 Distance prot. 1\ Z 1 Circuit breaker 1:Start auto.recl., Circuit breaker 1:Trip, Circuit
Line 1\ 21 Distance prot. 1\ Z 2 Circuit breaker 1:Trip, Circuit breaker 2:Trip
Circuit breaker 1 \General

General \Ref. for %-values
301.2311.101 Rated normal current All: 2000.00 A
301.2311.102 Rated voltage All: 500.00 kV
General \Breaker settings

301.2311.112 Current thresh. CB open All: 100 A
301.2311.113 1-pole operate allowed All: yes
Circuit breaker 1 \Trip logic

Trip logic
301.5341.101 Trip at 2ph short circuit All: 3-pole
301.5341.102 3-pole coupling All: with trip
301.5341.103 Reset of trip command All: with I<
Circuit breaker 1 \Circuit break.

Circuit break.
301.4261.101 Output time All: 0.1 s
301.4261.105 Indicat. of breaking values All: always
16 of 23
Automation Portal
Circuit breaker 1 \Manual close

Manual close
301.6541.101 Action time Settings group 1: 0.3 s
301.6541.102 CB open dropout delay Settings group 1: 0 s
Circuit breaker 1 \Control

Control
301.4201.101 Control model All: SBO w. enh. security
301.4201.102 SBO time-out All: 30 s
301.4201.103 Feedback monitoring time All: 1 s
301.4201.104 Check switching authority All: yes
301.4201.105 Check if pos. is reached All: yes
301.4201.106 Check double activat. blk. All: yes
301.4201.107 Check blk. by protection All: yes
Circuit breaker 1 \CB test

CB test
301.6151.101 Dead time All: 0.1 s
301.6151.102 Trip only All: false
301.6151.103 Consider current criterion All: false
Circuit breaker 1 \79 Auto. reclosing

General
301.1361.6601.101 79 operating mode All: with op., with act. time
301.1361.6601.102 CB ready check bef. start Settings group 1: no
301.1361.6601.103 Reclai. time aft.succ.cyc. Settings group 1: 3 s
301.1361.6601.104 Block. time aft. man.close Settings group 1: 1 s
301.1361.6601.105 Start signal supervis.time Settings group 1: 0.13 s
301.1361.6601.106 CB ready superv. time Settings group 1: 3 s
301.1361.6601.107 3-pole operate by 79 Settings group 1: yes
301.1361.6601.108 Evolving-fault detection Settings group 1: with trip
301.1361.6601.109 Response to evolv. faults Settings group 1: blocks 79
301.1361.6601.110 Max. dead-time delay Settings group 1: 0.5 s
301.1361.6601.111 Max. dead-time extension Settings group 1: 1.2 s
301.1361.6601.112 Send delay f. remot. close Settings group 1: 0.05 s
General \DLC, RDT

301.1361.6601.113 Dead-line check/reduc.d.t All: without
Cycle 1
301.1361.6571.102 Start from idle state allow. Settings group 1: yes
17 of 23
Automation Portal

301.1361.6571.103 Action time Settings group 1: 0.2 s
301.1361.6571.108 Dead time aft. 3-pole trip Settings group 1: 0.5 s
301.1361.6571.109 Dead time aft. evolv. fault Settings group 1: 1.2 s
301.1361.6571.111 CB ready check bef.close Settings group 1: no
301.1361.6571.110 Synchroch. aft. 3-pole d.t. Settings group 1: none
Cycle 1 \Intern. synchrocheck with

301.1361.6571.112 Intern. synchrocheck with
Circuit breaker 1 \25 Synchronization

General
301.1151.2311.127 Angle adjust. (transform.) Settings group 1: 0 °
Synchrocheck 1 \General
301.1151.5071.101 Min. operating limit Vmin Settings group 1: 360 kV
301.1151.5071.102 Max. operat. limit Vmax Settings group 1: 440 kV
301.1151.5071.110 Max.durat. sync.process Settings group 1: 30 s
301.1151.5071.108 Direct close command Settings group 1: no
301.1151.5071.126 Voltage adjustment Settings group 1: 1
Synchrocheck 1 \De-en.gized switch.

301.1151.5071.105 Close cmd. at V1< & V2> Settings group 1: no
301.1151.5071.106 Close cmd. at V1> & V2< Settings group 1: no
301.1151.5071.107 Close cmd. at V1< & V2< Settings group 1: no
301.1151.5071.103 V1, V2 without voltage Settings group 1: 20 kV
301.1151.5071.104 V1, V2 with voltage Settings group 1: 320 kV
301.1151.5071.109 Supervision time Settings group 1: 0.1 s
Synchrocheck 1 \Synchr. conditions

301.1151.5071.122 Max. voltage diff. V2>V1 Settings group 1: 20 kV
301.1151.5071.123 Max. voltage diff. V2<V1 Settings group 1: 20 kV
301.1151.5071.117 Max. frequency diff. f2>f1 Settings group 1: 0.1 Hz
301.1151.5071.118 Max. frequency diff. f2<f1 Settings group 1: 0.1 Hz
301.1151.5071.124 Max. angle diff. α2>α1 Settings group 1: 10 °
301.1151.5071.125 Max. angle diff. α2<α1 Settings group 1: 10 °
Sychr./Asycr.1 \General
18 of 23
Automation Portal

Sychr./Asycr.1 \De-en.gized switch.

301.1151.5041.105 Close cmd. at V1< & V2> Settings group 1: yes
301.1151.5041.106 Close cmd. at V1> & V2< Settings group 1: yes
Sychr./Asycr.1 \Asynchr. op.mode

301.1151.5041.114 Async. operating mode Settings group 1: on
301.1151.5041.113 CB make time Settings group 1: 0.06 s
Sychr./Asycr.1 \Synchr. op.mode

301.1151.5041.119 Sync. operating mode Settings group 1: off
301.1151.5041.120 f-threshold ASYN<->SYN Settings group 1: 0.01 Hz
301.1151.5041.121 Delay close command Settings group 1: 0 s

302.2311.102 Rated voltage All: 500.00 kV

302.2311.113 1-pole operate allowed All: yes

Trip logic
19 of 23
Automation Portal


Circuit break.
302.4261.105 Indicat. of breaking values All: always

Manual close
302.6541.102 CB open dropout delay Settings group 1: 0 s

Control

CB test
302.6151.101 Dead time All: 0.1 s
302.6151.102 Trip only All: false
302.6151.103 Consider current criterion All: false
Circuit breaker 2 \79 Auto. reclosing

General
302.1361.6601.101 79 operating mode All: with op., with act. time
302.1361.6601.102 CB ready check bef. start Settings group 1: no
302.1361.6601.103 Reclai. time aft.succ.cyc. Settings group 1: 3 s
302.1361.6601.104 Block. time aft. man.close Settings group 1: 1 s
302.1361.6601.105 Start signal supervis.time Settings group 1: 0.13 s
302.1361.6601.106 CB ready superv. time Settings group 1: 3 s
302.1361.6601.107 3-pole operate by 79 Settings group 1: yes
302.1361.6601.108 Evolving-fault detection Settings group 1: with trip
302.1361.6601.109 Response to evolv. faults Settings group 1: blocks 79
20 of 23
Automation Portal

302.1361.6601.110 Max. dead-time delay Settings group 1: 0.5 s
302.1361.6601.111 Max. dead-time extension Settings group 1: 1.2 s
302.1361.6601.112 Send delay f. remot. close Settings group 1: 0.05 s
General \DLC, RDT

302.1361.6601.113 Dead-line check/reduc.d.t All: without
Cycle 1
302.1361.6571.102 Start from idle state allow. Settings group 1: yes
302.1361.6571.103 Action time Settings group 1: 0.2 s
302.1361.6571.109 Dead time aft. evolv. fault Settings group 1: 1.2 s
302.1361.6571.111 CB ready check bef.close Settings group 1: no
302.1361.6571.110 Synchroch. aft. 3-pole d.t. Settings group 1: none
Cycle 1 \Intern. synchrocheck with

302.1361.6571.112 Intern. synchrocheck with

General

21 of 23
Automation Portal




302.1151.5041.119 Sync. operating mode Settings group 1: on
Disconnector 1 \Control
Control
22 of 23
Automation Portal

Disconnector 1 \Disconnector
Disconnector
601.5401.101 Maximum output time All: 10 s
601.5401.102 Seal-in time All: 0 s
601.5401.103 Switching-device type All: disconnector
23 of 23
Totally Integrated 7UT85 - REACTOR DE LÍNEA AYOLAS
Automation Portal
Settings
Device settings
Settings Value
Edit mode primary
DIGSI 5 uses following IP address 192.168.60.60 (Integrated Ethernet interface)
Hide settings in IEC 61850 structure Show all settings
Hide SIPROTEC extensions in IEC 61850 structure Show all SIPROTEC extensions
General \Device

General \Control
General \CFC
1 of 15
Automation Portal

91.150 Activate device test mode All: false
Localization
Time settings
General
Settings Value
Time source
Settings Value
Time source 1 Ch1:port E:SNTP
Time source 2 none
Time zone time source 1 All: UTC
Sync. latency time src.1 All: 0.1 μs

Settings Value
Time zone offset to UTC All: -240 min
Start of daylight sav. time Last Sunday in October at 12:00 AM
End of daylight sav. time Third Sunday in March at 12:00 AM

General

CT 3-phase \General
11.931.8881.115 CT connection All: 3-phase
2 of 15
Automation Portal

CT 1
11.931.3841.117 Phase All: I A
CT 2
11.931.3842.117 Phase All: I B
CT 3
11.931.3843.117 Phase All: I C
Supv. balan. I
Supv. ph.seq.I
Supv. sum I

CT 3-phase \General
11.932.8881.115 CT connection All: 3-phase
3 of 15
Automation Portal


CT 1
11.932.3841.117 Phase All: I A
CT 2
11.932.3842.117 Phase All: I B
CT 3
11.932.3843.117 Phase All: I C
Supv. balan. I
Supv. ph.seq.I
Supv. sum I
4 of 15
Automation Portal

General
11.951.2311.116 Term. 1,3,5,7 in dir. of obj. All: yes
CT 1
11.951.3841.117 Phase All: Ix
Power system \Meas.point V-3ph 1

VT 3-phase
11.941.8911.101 Rated primary voltage All: 500 kV
11.941.8911.104 VT connection All: 3 ph-to-gnd voltages
VT 1
11.941.3811.108 Phase All: V A
VT 2
11.941.3812.108 Phase All: V B
VT 3
11.941.3813.108 Phase All: V C
Supv. balan. V
5 of 15
Automation Portal
Supv. ph.seq.V
Supv. sum V
VT miniatureCB
Power system \Meas.point V-1ph 1

General
11.961.2311.101 Rated primary voltage All: 500 kV
VT 1
11.961.3811.108 Phase All: V B
VT miniatureCB

Control
51.791.2761.130 Fault recording All: with pickup
51.791.2761.131 Storage All: always
6 of 15
Automation Portal
Transformer side 1 \General

911.91.103 Rated apparent power All: 80 MVA
General \Side data

911.91.149 Neutral point Settings group 1: isolated
911.91.104 Winding configuration Settings group 1: Y (Wye)
911.91.163 Vector group numeral All: 0
911.91.130 Side number All: Side 1
911.91.210 MI3ph1 usesMeasP with ID All: 1
911.91.214 M I-1ph uses MeasP with ID All: 3
911.91.215 CT mismatch M I-3ph 1 All: 1.083
911.91.223 CT mismatch M I-1ph All: 1.083
Transformer side 1 \Process monitor

Transformer side 1 \49 Th.overl.-A 1
49 Th.overl. 1
911.191.601.2 Operate & flt.rec. blocked Settings group 1: yes
911.191.601.101 Threshold current warning Settings group 1: 86.6 A
911.191.601.104 Threshold thermal warn. Settings group 1: 90 %
911.191.601.105 Dropout threshold operate Settings group 1: 90 %
911.191.601.112 Emerg. start T overtravel Settings group 1: 300 s
911.191.601.106 K-factor Settings group 1: 1.1
911.191.601.110 Thermal time constant Settings group 1: 900 s
911.191.601.111 Cooling time constant Settings group 1: 3600 s
911.191.601.107 Imax thermal Settings group 1: 216.5 A
911.191.601.108 Imin cooling Settings group 1: 43.3 A
911.191.601.109 Temperature rise at Irated Settings group 1: 70 K
911.191.601.113 Storage of thermal replica Settings group 1: no
911.191.601.114 Behav. at I> Imax therm. Settings group 1: current limiting
911.191.601.118 Default temperature Settings group 1: 40 °C
911.191.601.117 Minimal temperature Settings group 1: -20 °C
Transformer side 1 \50/51 OC-3ph-B1

Definite-T 1
911.1941.661.27 Blk. w. inrush curr. detect. Settings group 1: yes
7 of 15
Automation Portal

Inverse-T 1
Transformer side 1 \50N/51N OC-gnd-B1

Definite-T 1
Inverse-T 1
Transformer side 1 \87N REF 1

87N REF 1
911.10081.2 Operate & flt.rec. blocked Settings group 1: no
911.10081.103 Threshold Settings group 1: 0.06 I/IrObj
911.10081.105 Slope Settings group 1: 0.05
911.10081.109 Operate delay Settings group 1: 0 s
8 of 15
Automation Portal
Transformer side 1 \Inrush detect.

Inrush detect.
911.4141.1 Mode All: on
911.4141.106 Operat.-range limit Imax Settings group 1: 649.5 A
911.4141.111 Blocking with CWA Settings group 1: yes
911.4141.110 Blocking with 2. harmonic Settings group 1: yes
911.4141.102 2nd harmonic content Settings group 1: 15 %
911.4141.112 Crossblocking Settings group 1: no
911.4141.109 Crossblocking time Settings group 1: 0.06 s
911.4141.114 Start flt.rec Settings group 1: yes
Transformer side 1\Ciruit-breaker interaction

Transformer side 1\ 87N REF 1 Circuit breaker 1:Trip, Circuit breaker 1:Start CB failure
Transformer side 1\ 49 Th.overl.-A 1\ 49 Th.overl. 1 Circuit breaker 1:Trip, Circuit breaker 1:Start CB failure
Transformer side 1\ 50/51 OC-3ph-B1\ Definite-T 1 Circuit breaker 1:Trip, Circuit breaker 1:Start CB failure
Transformer side 1\ 50/51 OC-3ph-B1\ Inverse-T 1 Circuit breaker 1:Trip, Circuit breaker 1:Start CB failure
Transformer side 1\ 50N/51N OC-gnd-B1\ Definite-T 1 Circuit breaker 1:Trip, Circuit breaker 1:Start CB failure
Transformer side 1\ 50N/51N OC-gnd-B1\ Inverse-T 1 Circuit breaker 1:Trip, Circuit breaker 1:Start CB failure
Transformer side 2 \General

912.91.103 Rated apparent power All: 80 MVA
General \Side data

912.91.149 Neutral point Settings group 1: isolated
912.91.104 Winding configuration Settings group 1: Y (Wye)
912.91.163 Vector group numeral All: 0
912.91.130 Side number All: Side 2
912.91.210 MI3ph1 usesMeasP with ID All: 2
912.91.215 CT mismatch M I-3ph 1 All: 1.083
Transformer side 2 \Process monitor

Transformer diff. 1 \87T diff. prot. 1
General
901.1691.2311.105 CT mismatch side 1 M3ph 1 All: 1.083
901.1691.2311.109 CT mismatch side 1 M1ph All: 1.083
901.1691.2311.110 CT mismatch side 2 M3ph 1 All: 1.083
901.1691.2311.191 Reference side is All: Side 1
901.1691.2311.151 MU-ID Side 1 Mp3ph 1 All: 1
901.1691.2311.155 MU-ID Side 1 Mp1ph All: 3
901.1691.2311.156 MU-ID Side 2 Mp3ph 1 All: 2
9 of 15
Automation Portal
I-DIFF \General
I-DIFF \Operate curve

901.1691.11041.3 Threshold Settings group 1: 0.1 I/IrObj
901.1691.11041.100 Slope 1 Settings group 1: 0.2
901.1691.11041.101 Intersection 1 Irest Settings group 1: 1.11 I/IrObj
901.1691.11041.102 Slope 2 Settings group 1: 0.5
901.1691.11041.103 Intersection 2 Irest Settings group 1: 5 I/IrObj
I-DIFF \Starting detection

901.1691.11041.106 Starting detection Settings group 1: no
901.1691.11041.107 Thresh. startup detection Settings group 1: 0.1 I/IrObj
901.1691.11041.108 Factor increasing char. Settings group 1: 2
901.1691.11041.109 Max. perm. Start. time Settings group 1: 5 s
I-DIFF \DC offset detection

901.1691.11041.110 Factor increasing char. DC Settings group 1: 2.3
I-DIFF \Inrush blocking

901.1691.11041.115 Blocking with 2. harmonic Settings group 1: yes
901.1691.11041.116 2nd harmonic content Settings group 1: 15 %
901.1691.11041.117 Crossblock. time 2nd har. Settings group 1: 0 s
901.1691.11041.118 Blocking with CWA Settings group 1: no
I-DIFF \Overexcit. blocking

901.1691.11041.121 Blocking with 3rd harm. Settings group 1: no
901.1691.11041.122 3rd harmonics content Settings group 1: 30 %
901.1691.11041.123 Crossblock. time 3rd har. Settings group 1: 0 s
901.1691.11041.124 Blocking with 5th harm. Settings group 1: yes
901.1691.11041.125 5th harmonics content Settings group 1: 30 %
901.1691.11041.126 Crossblock. time 5th har. Settings group 1: 0 s
901.1691.11041.127 Limit Idiff 3., 5. harmonics Settings group 1: 1.5 I/IrObj
I-DIFF \Ext. fault detection

901.1691.11041.128 Threshold add-on stabiliz. Settings group 1: 2 I/IrObj
901.1691.11041.129 Time of add-on stabiliz. Settings group 1: 0.3 s
901.1691.11041.130 Crossblk. time add-on st. Settings group 1: 0.3 s
10 of 15
Automation Portal
I-DIFF fast
901.1691.11071.3 Threshold Settings group 1: 2 I/IrObj
Transformer diff. 1\Ciruit-breaker interaction

Transformer diff. 1\ 87T diff. prot. 1\ I-DIFF Circuit breaker 1:Trip, Circuit breaker 1:Start CB failure
Transformer diff. 1\ 87T diff. prot. 1\ I-DIFF fast Circuit breaker 1:Trip, Circuit breaker 1:Start CB failure
Transform. neut.p 1 \General

General \Power-system data

921.9421.214 M I-1ph uses MeasP with ID All: 3
921.9421.223 CT mismatch M I-1ph All: 1.08
Transform. neut.p 1 \50N/51N OC-1ph-A1

Definite-T 1
921.211.12661.27 Blk. w. inrush curr. detect. Settings group 1: no
Definite-T 2
921.211.12662.27 Blk. w. inrush curr. detect. Settings group 1: no
Transform. neut.p 1\Ciruit-breaker interaction

Transform. neut.p 1\ 50N/51N OC-1ph-A1\ Definite-T 1 Circuit breaker 1:Trip, Circuit breaker 1:Start CB failure
Transform. neut.p 1\ 50N/51N OC-1ph-A1\ Definite-T 2 Circuit breaker 1:Trip, Circuit breaker 1:Start CB failure
11 of 15
Automation Portal



Trip logic

Circuit break.

Manual close

Control

CB test
201.6151.101 Dead time All: 0.1 s
12 of 15
Automation Portal
Circuit breaker 1 \50BF CB fail.1

50BF CB fail.1
201.4381.105 Holding int. start signal Settings group 1: yes
201.4381.107 Start via binary input All: 2 channel
201.4381.106 Holding ext. start signal Settings group 1: no
201.4381.111 Sup.time for release signl Settings group 1: 0.06 s
201.4381.103 CB aux.cont. crit. allowed Settings group 1: no
201.4381.104 Dropout Settings group 1: with effective criterion
201.4381.108 Retrip after T1 Settings group 1: parallel start T2, T1
201.4381.102 Threshold phase current Settings group 1: 25 A
201.4381.101 Threshold sensitive Settings group 1: 20 A
201.4381.109 Delay T1 for 3-pole retrip Settings group 1: 0.1 s
201.4381.110 Delay T2 for 3-pole trip Settings group 1: 0.2 s
201.4381.112 Minimum operate time Settings group 1: 0.1 s
201.4381.120 3I0 criterion All: Plausibility check
201.4381.121 I2 criterion All: Plausibility check
201.4381.122 Threshold 3I0 dir. release Settings group 1: 25 A
201.4381.123 Threshold I2 dir. release Settings group 1: 25 A
201.4381.124 Monit. time for BI ">Start" Settings group 1: 15 s
201.4381.125 Monit.tm. f.BI ">Release" Settings group 1: 15 s

General
201.1151.5071.101 Min. operating limit Vmin Settings group 1: 391.30 kV
201.1151.5071.102 Max. operat. limit Vmax Settings group 1: 478.26 kV

201.1151.5071.103 V1, V2 without voltage Settings group 1: 21.74 kV
201.1151.5071.104 V1, V2 with voltage Settings group 1: 347.83 kV

201.1151.5071.122 Max. voltage diff. V2>V1 Settings group 1: 21.74 kV
201.1151.5071.123 Max. voltage diff. V2<V1 Settings group 1: 21.74 kV
13 of 15
Automation Portal

201.1151.5041.101 Min. operating limit Vmin Settings group 1: 391.30 kV
201.1151.5041.102 Max. operat. limit Vmax Settings group 1: 478.26 kV

201.1151.5041.103 V1, V2 without voltage Settings group 1: 21.74 kV
201.1151.5041.104 V1, V2 with voltage Settings group 1: 347.83 kV


201.1151.5041.119 Sync. operating mode Settings group 1: on
Analog units \MT module 1

MT in 1
826.1832.5491.101 Meas. transduc. I/O type All: Current input
826.1832.5491.103 Unit All: m
826.1832.5491.108 Resolution All: 0.1
826.1832.5491.107 Range active All: false
826.1832.5491.104 Conversion factor All: 100
14 of 15
Automation Portal
MT in 2
826.1832.5492.103 Unit All: m
826.1832.5492.108 Resolution All: 0.1
MT in 3
826.1832.5493.103 Unit All: m
826.1832.5493.108 Resolution All: 0.1
MT in 4
826.1832.5494.103 Unit All: m
826.1832.5494.108 Resolution All: 0.1
15 of 15
B00_R00_F006_prn_16_42_04
AYOLAS / 500/220kV / 87B 500kV /

SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
AYOLAS / 500/220kV / 87B 500kV / B00_R00_F006
MLFB: 7SS5220**B921!A0
Parameter-set version: V04.72.01
Device path: C:\PRESEL\AYOLAS DIGSI 4 V4.88
\AYOLAS ECP 87B 500KV\P7DI\GV\SD\00000009
Author: A. Cangrejo
Creation date: 02.05.13 09:26:28
Last modified: 28.04.18 15:05:06
Operating mode: Offline
Comment:
Setting values in: Secondary value description
PRINT - CONTENTS
1 Substation Data ....................................................................................................................................................… 3
1.1 Group Power System Data 1; Group Power System ...........................................................................................… 3
2 Settings groups ....................................................................................................................................................… 4
2.1 Group Protection general; Group Power System ..................................................................................................... 4
2.2 Group Bus Bar Protection; Group Bus Zone ............................................................................................................ 4
2.3 Group Bus Bar Protection; Group Check Zone ........................................................................................................ 4
2.4 Group Breaker Failure Protection; Group Breaker Failure ....................................................................................... 4
2.5 Group Monitoring; Group General ........................................................................................................................… 5
2.6 Group Monitoring; Group Idiff Superv ..................................................................................................................… 5
2.7 Group Monitoring; Group 0-Cross Superv ............................................................................................................… 5
2.8 Group Monitoring; Group CB/DCO Superv ..........................................................................................................… 5
2.9 Group Monitoring; Group CB Test ........................................................................................................................… 6
3 Bay unit allocation ................................................................................................................................................… 7
3.1 Bay unit allocation ................................................................................................................................................… 7
4 Bay units ...............................................................................................................................................................… 8
4.1 Function blocks ....................................................................................................................................................… 8
4.1.1 Group Bay Unit @01; Group General ..................................................................................................................… 8
4.1.2 Group Bay Unit @01; Group Breaker Failure .......................................................................................................… 8
4.1.3 Group Bay Unit @01; Group End fault stage .......................................................................................................… 9
4.1.4 Group Bay Unit @01; Group Breaker ...................................................................................................................… 9
4.2 Function blocks ....................................................................................................................................................… 9
4.2.1 Group Bay Unit @02; Group General ..................................................................................................................… 9
4.2.2 Group Bay Unit @02; Group Breaker Failure .......................................................................................................… 9
4.2.3 Group Bay Unit @02; Group End fault stage .....................................................................................................… 10
4.2.4 Group Bay Unit @02; Group Breaker .................................................................................................................… 10
4.3 Function blocks ..................................................................................................................................................… 10
4.3.1 Group Bay Unit @03; Group General ................................................................................................................… 10
4.3.2 Group Bay Unit @03; Group Breaker Failure .....................................................................................................… 11
4.4 Function blocks ..................................................................................................................................................… 12
4.5 Function blocks ..................................................................................................................................................… 13
Page 1 of 15
B00_R00_F006_prn_16_42_04
AYOLAS / 500/220kV / 87B 500kV /

SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06

4.6 Function blocks ..................................................................................................................................................… 14
Page 2 of 15
B00_R00_F006_prn_16_42_04
Substation Data
AYOLAS / 500/220kV / 87B 500kV /
SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
1 Substation Data
1.1 Group Power System Data 1; Group Power System

Group Power System Data 1; Group Power System
No. Settings Value Group
5104 Nominal frequency 50 Hz All
Page 3 of 15
B00_R00_F006_prn_16_42_04
Settings groups
AYOLAS / 500/220kV / 87B 500kV /
SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
2 Settings groups
2.1 Group Protection general; Group Power System

Group Protection general; Group Power System
6106 Minimum duration of TRIP command 0.15 sec All

6320A Sensitive characteristic switchover blocked All
6318 Control release for bay units released All
5401 Selective protection for transfer busbar YES All
5112A Bay unit output enable during test mode NO All
5108A Test mode for module SK OFF All
5111 Language of bay units English All
6120A Additional criterion for tripping nonexistent All
2.2 Group Bus Bar Protection; Group Bus Zone

Group Bus Bar Protection; Group Bus Zone
6101 Stabilizing factor - BZ 0.65 All

6102 Diff-current threshold - BZ 1.00 I / Ino All
2.3 Group Bus Bar Protection; Group Check Zone

Group Bus Bar Protection; Group Check Zone
6103 Stabilizing factor - CZ 0.50 All

6104 Diff-current threshold - CZ 1.00 I / Ino All
2.4 Group Breaker Failure Protection; Group Breaker Failure

Group Breaker Failure Protection; Group Breaker Failure
6201 Stabilizing factor BF protection 0.25 All
Page 4 of 15
B00_R00_F006_prn_16_42_04
AYOLAS / 500/220kV / 87B 500kV /

SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
2.5 Group Monitoring; Group General

Group Monitoring; Group General
6317 Supervision bin. input TRIP-Release 0.06 sec All
2.6 Group Monitoring; Group Idiff Superv

Group Monitoring; Group Idiff Superv
6306 Differential current supervision OFF All

6307 Time delay for diff-current supervision 2.00 sec All
6308 Limit value diff-current supervision -BZ 0.25 I / Ino All
6309 Limit value diff-current supervision -CZ 0.20 I / Ino All
6310 Diff-current supervision mode -BZ blocking during the fault All
6311 Diff-current supervision mode -CZ alarm without blocking All
2.7 Group Monitoring; Group 0-Cross Superv

Group Monitoring; Group 0-Cross Superv
6312A Zero crossing supervision ON All

6313A Threshold for zero crossing supervision 0.50 I / Ino All
2.8 Group Monitoring; Group CB/DCO Superv

Group Monitoring; Group CB/DCO Superv
6315 CB supervision time 7.00 sec All

6301 Limit value disconnector time 15.00 sec All
6302 Reaction on disconnector malfunction alarm without blocking All
6303 Treatment disconnector status on DC fail old disconnector status All
6304 Treatment disconn. status not plausible old disconnector status All
Page 5 of 15
B00_R00_F006_prn_16_42_04
Group Monitoring; Group CB Test
AYOLAS / 500/220kV / 87B 500kV /
SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
2.9 Group Monitoring; Group CB Test

Group Monitoring; Group CB Test
6316 Limit value for circuit breaker test 0.05 I / In All
Page 6 of 15
B00_R00_F006_prn_16_42_04
Bay unit allocation
AYOLAS / 500/220kV / 87B 500kV /
SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
3 Bay unit allocation
3.1 Bay unit allocation

Bay unit allocation
No. bay unit SIPROTEC device
1 BU@ 1 B01_R11_F016
2 BU@ 2 B02_R12_F016
3 BU@ 3 B01_R21_F016
4 BU@ 4 B02_R22_F016
5 BU@ 5 B03_R13_F016
6 BU@ 6 B03_R23_F016
Page 7 of 15
B00_R00_F006_prn_16_42_04
Bay units
AYOLAS / 500/220kV / 87B 500kV /
SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
4 Bay units
4.1 Function blocks
4.1.1 Group Bay Unit @01; Group General

Group Bay Unit @01; Group General
0112 Bay status in service All

0106A Combi-Coupler NO All
0151A Maintenance for disconnector 1 YES All
0156A Maintenance for CB YES All
4.1.2 Group Bay Unit @01; Group Breaker Failure

Group Bay Unit @01; Group Breaker Failure
0114 Binary input mode / supervision BF Initiation and release with supervision All
0115 Operation mode BF TRIP repetition with current query All
0116 Low-current mode BF OFF All
0117 TRIP repeat mode 3pole All
0118 Current threshold for BF 0.25 I / In All
0119A Current threshold for BF - EF 0.20 I / In All
0120 Time delay for BF with 1-pole faults 0.13 sec All
0121 Time delay for BF with multi-pole faults 0.20 sec All
0122 Time delay for BF low current mode 0.20 sec All
0123A Time delay for BF pulse mode 0.20 sec All
0124 Time delay BF after CB fault 0.10 sec All
0125 Time delay for TRIP repeat 0.10 sec All
0126 Time delay for CB open 0.05 sec All
0127 Supervision bin. input BF-release 15.00 sec All
0128 Supervision time BF start / release 0.06 sec All
Page 8 of 15
B00_R00_F006_prn_16_42_04
Group Bay Unit @01; Group End fault stage
AYOLAS / 500/220kV / 87B 500kV /
SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
4.1.3 Group Bay Unit @01; Group End fault stage

0129 End fault protection ON All
4.1.4 Group Bay Unit @01; Group Breaker

Group Bay Unit @01; Group Breaker
0113 Current threshold for TRIP release 0.05 I / In All
4.2 Function blocks



Page 9 of 15
B00_R00_F006_prn_16_42_04
AYOLAS / 500/220kV / 87B 500kV /

SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
Group Bay Unit @02; Group Breaker Failure(2)



4.3 Function blocks


Page 10 of 15
B00_R00_F006_prn_16_42_04
AYOLAS / 500/220kV / 87B 500kV /

SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06



Page 11 of 15
B00_R00_F006_prn_16_42_04
Function blocks
AYOLAS / 500/220kV / 87B 500kV /
SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
4.4 Function blocks



Page 12 of 15
B00_R00_F006_prn_16_42_04
AYOLAS / 500/220kV / 87B 500kV /
SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06


4.5 Function blocks



Page 13 of 15
B00_R00_F006_prn_16_42_04
AYOLAS / 500/220kV / 87B 500kV /

SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06
Group Bay Unit @05; Group Breaker Failure(2)



4.6 Function blocks


Page 14 of 15
B00_R00_F006_prn_16_42_04
AYOLAS / 500/220kV / 87B 500kV /

SIMATIC B00_R00_F006/7SS522 28.04.18 16:42:06



Page 15 of 15
Totally Integrated 7VK87 - 50BF CORTE B AYOLAS
Automation Portal
Settings
Device settings
Settings Value
Edit mode primary
DIGSI 5 uses following IP address 10.200.4.34 (Port E)
Hide settings in IEC 61850 structure Show all settings
Hide SIPROTEC extensions in IEC 61850 structure Show all SIPROTEC extensions
General \Device
91.115 Set. format residu. comp. All: Kr, Kx

91.111 Energy restore interval Settings group 1: 10 min
91.112 Energy restore time Settings group 1: none
91.120 Energy restore Settings group 1: latest value
General \Control
91.121 Energy restore by A.time All: false
1 of 8
Automation Portal
General \CFC

91.150 Activate device test mode All: false
Localization
Time settings
General
Settings Value
Time source
Settings Value
Time source 1 Ch1:port E:SNTP
Time source 2 none
Time zone time source 1 All: UTC
Sync. latency time src.1 All: 0.10 μs

Settings Value
Time zone offset to UTC All: -240 min
Start of daylight sav. time First Sunday in October at 12:00 AM
End of daylight sav. time Third Sunday in March at 12:00 AM

General
2 of 8
Automation Portal
Power system \Corriente Corte

CT 3-phase \General
11.931.8881.115 CT connection All: 3-phase + IN

11.931.8881.107 CT error changeover All: 1
11.931.8881.108 CT error A All: 5 %
11.931.8881.109 CT error B All: 15 %
CT 1
11.931.3841.117 Phase All: I A
CT 2
11.931.3842.117 Phase All: I B
CT 3
11.931.3843.117 Phase All: I C
CT 4
11.931.3844.117 Phase All: IN
Brk.wire det.
11.931.5581.101 Mode of blocking Settings group 1: not blocking
11.931.5581.102 Delta value for autoblock Settings group 1: 1
3 of 8
Automation Portal
Supv. balan. I
Supv. ph.seq.I
Supv. sum I
Supv.ADC sum I
Power system \Tension

VT 3-phase
11.941.8911.103 Matching ratio Vph / VN All: 1.73
11.941.8911.104 VT connection All: 3 ph-to-gnd volt. + VN
VT 1
11.941.3811.108 Phase All: V A
VT 2
11.941.3812.108 Phase All: V B
VT 3
4 of 8
Automation Portal

11.941.3813.108 Phase All: V C
VT 4
11.941.3814.108 Phase All: VN
Supv. balan. V
Supv. ph.seq.V
Supv. sum V
VT miniatureCB

Control
51.791.2761.130 Fault recording All: with pickup
51.791.2761.131 Storage All: with trip
Line 1 \General
5 of 8
Automation Portal

21.9001.103 Rated apparent power All: 1039.2 MVA
General \Line data

21.9001.149 Neutral point Settings group 1: grounded
21.9001.113 X per length unit Settings group 1: 0.2793 Ω/km
21.9001.114 Line length Settings group 1: 16 km
21.9001.108 Line angle Settings group 1: 86.8 °
21.9001.104 Kr Settings group 1: 1.41
21.9001.105 Kx Settings group 1: 0.36
21.9001.119 CT saturation detection All: yes
21.9001.120 CT saturation threshold Settings group 1: 12000 A
21.9001.111 Series compensation All: no
Line 1 \Process monitor

Closure detec.
21.1131.4681.101 Operating mode Settings group 1: Manual close only
21.1131.4681.102 Action time after closure Settings group 1: 0.05 s
21.1131.4681.103 Min. time feeder open Settings group 1: 0.25 s
1pol.open det.
21.1131.4711.101 Operating mode Settings group 1: with measurement
Volt.criterion
21.1131.4801.101 Threshold U open Settings group 1: 135.14 kV
Line 1 \50BF E0
Standard 1
21.971.3901.101 Activation Settings group 1: always active
6 of 8
Automation Portal

301.2311.101 Rated normal current All: 1200 A

301.2311.113 1-pole operate allowed All: no

Trip logic
301.5341.103 Reset of trip command All: with dropout

Circuit break.

Manual close

Control

CB test
301.6151.101 Dead time All: 0.1 s
7 of 8
Automation Portal
Circuit breaker 1 \50BF CB fail.1

50BF CB fail.1
301.4381.105 Holding int. start signal Settings group 1: yes
301.4381.107 Start via binary input All: 2 channel
301.4381.106 Holding ext. start signal Settings group 1: no
301.4381.108 Sup.time for release signl Settings group 1: 0.06 s
301.4381.103 CB aux.cont. crit. allowed Settings group 1: no
301.4381.104 Dropout Settings group 1: with effective criterion
301.4381.110 Retrip after T1 All: parallel start T2, T1
301.4381.102 Threshold phase current Settings group 1: 300 A
301.4381.101 Threshold sensitive Settings group 1: 240 A
301.4381.111 Delay T1 for 3-pole retrip Settings group 1: 0.1 s
301.4381.112 Delay T2 for 3-pole trip Settings group 1: 0.2 s
301.4381.115 Minimum operate time Settings group 1: 0.1 s
301.4381.120 3I0 criterion All: Plausibility check
301.4381.121 I2 criterion All: Plausibility check
301.4381.122 Threshold 3I0 dir. release Settings group 1: 250 A
301.4381.123 Threshold I2 dir. release Settings group 1: 250 A
301.4381.124 Monit. time for BI ">Start" Settings group 1: 15 s
301.4381.125 Monit.tm. f.BI ">Release" Settings group 1: 15 s
8 of 8

Anexo Ii

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Anexo Ii

Uploaded by

Copyright:

Available Formats

Totally Integrated 7SL87 - LINEA A VILLA HAYES

General \Setting change

General \Chatter blocking

General \Test support

Time zone and daylight saving time

Power system \General

Power system \Tensión derv.AB

Power system \Barra

Power system \Meas.point I-3ph 1

CT 3-phase \CT phases

Recording \Fault recorder

General \Line data

Line 1 \Process monitor

Line 1 \68 P.swing blk

68 P.swing blk \Zones to be blocked

Line 1 \Fault locator

Number Settings Value

85-21Perm.over \Send with

85-21Perm.over \Operate with

85-21Perm.over \Trans. block. with

Line 1 \85-67N Dir. comp.

85-67N Dir.com \Send with

85-67N Dir.com \Operate with

85-67N Dir.com \Trans. block. with

Line 1 \Switch onto fault 1

Line 1 \50/51 OC-3ph 1p 1

Line 1 \50N/51N OC-gnd-A1

Line 1 \50 high-speed 1pol 1

Line 1 \67N GFP gnd.sys.1

Number Settings Value

Number Settings Value

Line 1 \59 Overvolt.-3ph 1

Line 1 \21 Distance prot. 1

Number Settings Value

Line 1 \Weak infeed

Line 1 \87 Line diff. prot.

Number Settings Value

Line 1 \87 Stub diff. prot. 1

Line 1\Ciruit-breaker interaction

Protection group Circuit-breaker group(s)

Circuit breaker 1 \General

General \Breaker settings

Circuit breaker 1 \Trip logic

Circuit breaker 1 \Circuit break.

Circuit breaker 1 \Manual close

Circuit breaker 1 \Control

Circuit breaker 1 \CB test

Circuit breaker 1 \79 Auto. reclosing

General \DLC, RDT

Number Settings Value

Cycle 1 \Intern. synchrocheck with

Circuit breaker 1 \25 Synchronization

Synchrocheck 1 \De-en.gized switch.

Synchrocheck 1 \Synchr. conditions

Number Settings Value

Sychr./Asycr.1 \De-en.gized switch.

Sychr./Asycr.1 \Asynchr. op.mode

Sychr./Asycr.1 \Synchr. op.mode

Circuit breaker 2 \General

General \Breaker settings

Circuit breaker 2 \Trip logic

Number Settings Value