CS3000 Service v6 E5 09 1 E

Fire Alarm System
Salwico CS3000
Service manual
Ver. 6
çConsilium
The contents of this document are subject to revision without notice due to continued progress in
methodology, design and manufacturing. Consilium assumes no legal responsibility for any error
or damage resulting from the usage of this document.
Edition 5, 09 1 E, August 2009.

Document no. S-4-007.875
Part no: 070073
© 2004-2009, Consilium Fire & Gas AB
Consilium Marine AB
P.O. Box 8763
SE-402 76 GÖTEBORG
SWEDEN
Tel: +46-31-710 77 00, Fax: +46-31-710 78 00
E-mail: cmab.got@consilium.se
Internet: www.consilium.se
Service Manual CS3000 Contents i
Contents
About this manual ..................................................................................................... ii
Chapter 1: Control unit

Service mode ............................................................................. 1-1
Set address ........................................................................ 1-1
Bypass built-in short circuit isolators ................................... 1-1
Chapter 2: The circuit board of the control unit

Input/Output board IKK-4................................................. 2-1
Chapter 3: The circuit boards of the central unit

Loop processor board SPK-2 ............................................... 3-01
Alarm processor board LPK-2 .............................................. 3-09
Relay board ARK-2 .... .............................................................. 3-13
Input board INK-2 .................. ................................................... 3-18
Output board UTK-2 ................................................................ 3-22
Interface board GSK-2 ............................................................. 3-26
Interface board RS232K-2 ..................................................... 3-30
Interface board KPK-2 ............................................................ 3-34
Rack CSR-3200. ....................................................................... 3-38
Power unit CSS-3300 ... .......................................................... 3-40
Appendix A. DIP switch settings ............................................................... A-1
Appendix B. Fault codes CS3000 version 4...................................... B-1
Appendix C. Fault codes CS3000 version 6..................................... C-1
Document no.: S-4-007.875/E

Prepared: 1995-03-17 Fia
Revision: R4 2004-03-15 BM
© 1995, Consilium Marine AB

Service Manual CS3000 Contents ii
About this manual

This manual is intended to be used by personnel who maintain and perform
service on the CS3000 system.
Chapter Control Unit gives a general description on how the Control unit
works.
Chapter The Circuit Board of the Control Unit describes the functions of the
Control unit’s circuit board.
For information regarding the Central unit’s various circuit boards refer to The
Circuit Boards of the Central Unit chapter.
DIP switch settings for all different parts of the CS3000 system are listed in
the DIP Switch Settings appendix.
The fault codes for CS3000 version 4 and 6 are listed in the Fault Codes
CS3000 Version 4 and Fault Codes CS3000 Version 6 appendixes
respectively.
For a more detailed description of the system refer to the CS3000 Reference
Manual.


Service Manual CS3000 Chapter 1: Service mode 1-1
Control unit
Chapter 1: Control unit

Service mode
The control unit includes a fourth access level to be used only by the service
engineer. There are two functions in the service mode: bypass the built-in short
circuit isolators and definition of control unit address.
Set address
(Access level 4)
Each control unit in the system must have a unique address in the interval 217
- 232. The control unit number must correspond with the number defined in
the Definition program. The control unit address must be set after the system
definition is downloaded and the system is restarted.
• Press F4 (MENU) until SERVICE is displayed on line 4.
• Press F1 (SERVICE).
• Press F1 (ADDRESS).
• Enter the address for the control unit. The address interval is 217 - 232.
Bypass built-in short circuit isolators

The built-in short circuit isolators, two on each loop, are bypassed when you
activate the SERVICE function. The short circuit isolators remain bypassed
until you activate them again.
• Press F4 (MENU) until SERVICE is displayed on line 4.
• Press F1 (SERVICE).


Service Manual CS3000 Chapter 2: Input/Output board IKK-4 2-1
The circuit board of the control unit
Chapter 2: The circuit board of the control unit

Input/Output board IKK-4
General
The Input/output board (IKK-4) interfaces the control unit processor board to
the system loop. The IKK-4 board also includes circuits for transient
suppression of all external signals. The IKK-4 board is controlled by the
control unit board, via the address and data busses.
Handling
Fuses
Fuse Fuse rating Fault code

F1: Control unit panel 500 mAT 5x20 mm Not supervised
F2: Main fuse 100 mAT 5x20 mm Not supervised
F3: Main fuse for F4-F5 500 mAT 5x20 mm Not supervised
F4: Power supply ext. device 315 mAT 5x20 mm Not supervised
F5: Power supply 315 mAT 5x20 mm Not supervised


Function
Block diagram


1. Data buffer
The data bus is buffered before entering/leaving the board.
2. Address decoder
The address decoder selects the different blocks. The address decoder is
controlled by the control unit board.
3. Regulator
The regulator converts power voltage to 5 VDC.
4. Expansion
Future expansion possibilities. Not used.
5. Board ID
The control unit board reads the IKK-4 ID.
6. Inputs
Reads all external inputs.
7. Outputs
Controls the four transistor outputs.
8. Buzzer
An external buzzer may be connected via a transient protected output. The
buzzer will be parallel connected to the fire alarm and the fault buzzer on the
control unit board.
9. Barrier
The RS 232 communication is protected against transients before entering the
control unit board.
10. System loop barrier

Transient barrier for the system loop.
11. Barrier
The power supply voltage output is protected against external transients.
12. Power supply output

A fused and fault supervised output for power supply to an external device.
13. Opto-isolated inputs

Four opto-isolated transient protected external inputs.
14. Opto-isolated outputs

Four transistor outputs. Deactivated at hang-ups in the programme execution.


Technical data
Board size: 145 x 107 mm
Ambient temperature: -10°C - +70°C.

Ambient humidity: 96% Rh.
Input power: Uin : 24 VDC (-20% - + 25%).

Current consumption: Iin nom: 15 mA
Iin max: 40 mA.
Outputs: 4 opto-isolated sourcing outputs
Inputs: 4 opto- isolated inputs, active high


Service manual CS3000 Chapter 3: Loop processor board SPK-2 3-1
The circuit boards of the central unit
Chapter 3: The circuit boards of the central unit

Loop processor board SPK-2
The loop processor boad SPK-2 exists in three different models. Model 1 and
model 2 differs only in the exterior of the front panel, whereas Model 3 has an own
block diagram.
General
The loop processor board SPK-2 controls and supervises two detector loops with
analogue and addressable detectors. The detectors are constantly polled in order to
detect faults or changes in alarm status. Detector-initiated alarms are also
recognised and verified. The events are reported to the LPK-2 and proper hardware
signals are then activated.
Handling
Indications
Model 1 There are nine LEDs on the front panel of the board.
No 1 (green) when lit:proper voltage supply.
No 2 (yellow) when lit:fault in loop #1.
No 3 (red) when lit:fire alarm in loop #1.
No 6 (yellow) when lit:local processor failure
No 7 (in service mode) will flash synchronously with the central unit’s
communication with the loop-PCB.
No 8, 9 (in service mode) will flash synchronously with polling of the
loop-units
Model 2 & 3 There are eight LEDs on the front panel of the board.
No 1 (green) when lit:proper voltage supply.
No 2 (yellow) when lit:local processor failure.
No 3, 4 (green) (in service mode) will flash synchronously with polling of the
loop-units


Fuse
The battery voltage is fused. If the fuse is blown a signal is activated in the back
plane. The fuse is accessible on the front panel of the board, and can be used for
disconnecting the power.
Fuse ratings:
Model 1 & 2: 1 AT 5x20 mm
Model 3: 1.6 AT 5x20 mm
Setting the address
The address of loop #1 of the board is set with a DIP-switch (SW1), with 8
switches. Bit #1 is set with SW1-1, and bit #8 with SW1-8. The address of loop #2
is automatically set by the system to the next consecutive value.
Set the address of each SPK-2 according to the definition in the Definition
program.
Restarting the board
Remove the fuse from the board to disconnect the power. When the fuse is put back
on, the board is restarted.
Replacing the board
To replace the SPK-2 follow these steps:
1. Disconnect the power by removing the fuse.
WARNING!
The power must be disconnected before the board is removed.
2. Remove the board and replace it with the new board.


Function
Block diagram Model 1 & Model 2
NB! In the diagram blocks 8 - 14 are doubled, one set for each detector loop.


1. Power supply
Power supply for processor, memory and logic of the loop processor board.
2. Control logic
Control logic for activation and blocking of hardware signals to the back plane.
LEDs for indication of status and communication are also controlled in this block.
3. LED indications
LEDs for indicating status of fire, fault, communication and voltage.
4. Drivers
Drivers for adapting hardware signal to the back plane.
5. CPU/Memory/watchdog
This is the main block of the SPK-2 board. The CPU controls both of the detector
loops and the communication with the LPK-2. The memory circuits contain the
programme code, default data for the detectors and status information. The
watchdog supervises the processor and checks for hang-ups in the programme
execution.
6. Address switch
The 8-bit address of the SPK-2, i.e. the loop number, is set with the DIP switch.
7. LPK communication
Interface for back plane communication.
8. DC/DC converter
The DC/DC-converter converts the battery voltage from the back plane to 30 VDC,
for the detector loops.
9. Signal filter
Signal filter for the communication signals.
10. Communication direction switch
For closed loops the choice of direction for the communication is made with this
switch.
11. Disconnection switch
With this switch the entire detector loop may be disconnected.
12. Barrier
Barrier for protecting the loops against incoming transients.
13. Basic-Alarm detection
Circuit for the detection of a basic-alarm.
14. Transmitter/receiver
Transmitter, receiver and interface for the processor bus.
15. Buses
The control signal bus contains signals to control the reading and writing of devices
connected to the address bus and the data bus.


Block diagram Model 3

SPK-2 Model 3 can be split into three functions: Power supply, loop and processor
with memory. The power supply provides the board with loop power and power for
the logic and the processors. The loop part contains electronics for two loops and
handles power supply for the loop and sending/transmitting of IDA and NOSE
messages. The processor controls the loops and communicates with the LPK via the
RS485 channel of the back plane.
The whole board is galvanically isolated from the CS3000 rack.


DC/DC converter
Power is taken from the back plane and converted via a galvanically isolated
DC/DC converter into 35V. The 35V is used to power feed the loops and is also
converted to 5V for the logic. The voltage feed is fused.
Control logic
Signals in the back plane for fuse fault, voltage fault and prim-alarm. All signals
are galvanically isolated between SPK-2 and the back plane.
LEDs
Indicating status of the system. Some LEDs are active only in service mode.
CPU, memory and watchdog
The CPU controls and supervises the communication on both loops and also
communicates with the LPK. The memory contains program code with initial
values for the loop units and also gives status information. The watchdog
supervises the CPU and activates a reset signal to the CPU in case of malfunction.
Address switch
An 8-pole DIP-switch deciding the physical address of the board.
RS485 LPK communication
One asyncronous channel of the processor is used for communication with the
LPK. These signals are adapted to the RS485 levels and are galvanically separated
from the back plane.
Service plug
RS232 channel used for service, debugging and downloading of code.
Earth fault measurement
Measuring positive and negative earth faults. Since the board is galvanically
separated from the rest of the system, the measurement is a local indication of earth
faults from the loops. Earth fault is not measured when the board is used for
connection of GSK.
Loop : EMC protection
Protecting the electronics from various EMC disturbances.
Loop: Short circuit protection
Contains two parts, one part automatically disconnecting the loop power when the
current consumption exceeds allowed limit and one part which is used to control
the power feed to the primary and/or secondary side of the loop.
Loop: Line power
Feeding the loop with correct DC voltage and current and adapting the loop to the
signalling used on IDA and NOSE loops.
Loop: Current measurement
Measuring the DC current which is fed to the loop.
Loop: Signal filter
Separating and filtering out IDA/NOSE communication from the DC supply
voltage on the loop.
Loop: Line modem
Sending and receiving IDA/NOSE communication. Communication with the
processor via serial channel.


Jumpers Model 3
JP2 JP4
JP1 JP3
JP1 Must always be strapped in normal operation. The strap enables the
watchdog.
JP2 Never strapped during normal operation.
JP1 and JP2 are only strapped differently during production when the card is
programmed the first time.
JP3 Normally strapped.

JP4 Normally strapped.
JP3 and JP4 can be used to enhance reception of loop communication in case of
loops with communication problems.


Technical data Model 1 & 2

Board size: Single Europe board, 100 x 160 mm
Front panel: Anodised aluminium, width 6 TE(30.1 mm)
Ambient temperature: -10°C to +70°C

Ambient humidity: 96% Rh
Input power: Uin : 24 VDC (-20% - + 25%)

Iin max: 160 mA
Output voltage: Uut : 30 VDC (+/- 5%)

Output current: Iut nom: 45 mA
Iut max: 125 mA
Model 3
Board size: Single Europe board, 100 x 160 mm
Front panel: Anodised aluminium, width 6 TE(30.1 mm)
Ambient temperature: -10°C to +70°C


Current consumption: Iin nom: 120 mA (no loop units connected)
Iin max: 1300 mA
Output voltage: Uut : 32 - 34 VDC

Output current: Iut max: 300 mA/loop


Service manual CS3000 Chapter 3: Alarm processor board LPK-2 3-9
Alarm processor board LPK-2

General
The alarm processor board LPK-2 controls and supervises the external alarm
devices. The board also controls external functions such as fans, fire doors and
release of fire extinguishing agents through relay outputs. The LPK-2 also
monitors all communication within its own central with all loop processor
boards. The LPK-2 that is situated in the main central unit also monitors all
communication on the system loop with control units and with external
computers, printers, etc.
The alarm processor board exists in two different models, which differ only in
the exterior of the front panel. Model 2 has an additional connector for
downloading data from a computer.
Handling
Indications
There are six LEDs on the front panel of the board.
No 1 (green) when lit: proper voltage supply.

No 2 (red) when lit: fire alarm has been given on the fire
1
brigade relay output.
2
3 No 3 (yellow) when lit: fault has been detected.
4 No 4 (yellow) when lit: local system failure
5
6
No 5 (green) (in service mode) will flash synchronously with the
central unit’s communication with the
loop-PCB.
No 6 (green) (in service mode) will flash synchronously with the
communication on the system loop.
Fuse
Salwico LPK-2
The battery voltage is fused. If the fuse is blown a signal is activated in
the back plane. The fuse is accessible on the front panel of the board,
and can be used for disconnecting the power.
Fuse rating: 1 A 5x20 mm
Model 1 Model 2
Setting the address

The address of the board is set with a DIP-switch (SW1), with 8 switches.
• Sw 6 (when set) activates the service mode.
• Sw 7 (when set) allows communication only on loop 1 (the primary loop).
• Sw 8 (when set) allows communication only on loop 2 (the secondary loop).
• Sw 6, 7, 8 (when set together) forces downloading of definition data.
The address interval is 1 - 16. The LPK-2 board controlling and supervising the
main central unit is always set to one. The addresses of the other LPK-2, if
installed in the system, are set according to the definition in the Definition
program.


Remove the fuse from the board to disconnect the power. When the fuse is put
back on, the board is restarted.
Replacing the board
To replace the LPK-2 follow these steps:
2. To avoid activation of Bells, remove fuses F5-F10 on ARK-2.
WARNING!


Function
Block diagram
BACK PLANE
1 FUSE
DC/DC
24 VDC
CONVERTER
TX/RX 6
INT.COM. TX/RX
3 2 LOOP (SPK)
LED- DIR
INDICATIONS
CPU 8 TX SYSTEM
SYSTEM
MEMORY TX/RX LOOP 1
COM. LOOP RX
WATCH-DOG
TX/RX 7 (CSM/LPK)
4 LOOP
ADDRESS COM. CONTR. SWITCH
SWITCH SYSTEM 8 TX SYSTEM
COM. LOOP LOOP 2
RX
TX/RX (CSM/LPK)
5 ADDRESS/DATA/CONTROL 9
REAL TIME DATA/ADDRESS
CLOCK BUFFERS
10
BACK PLANE
SIGNALS
11
BLOCK BASIC
ALARM
RELAY 12
OUTPUTS


1. DC/DC converter
The DC/DC circuit converts the battery voltage of the back plane to 5 VDC,
which is supplied to all logical circuits on the board.
2. CPU/Memory/Watchdog
This is the main block of the LPK-board. The CPU uses the memory circuits for
executing the programme code. There is also a non-erasable memory containing
the system configuration and the external controls. The watchdog supervises the
processor and checks that there are no hang-ups in the programme execution.
3. LED indications
One green LED indicates that the board is power supplied. If the watchdog is
activated (possible fault in the board), a yellow LED is lit, indicating system
fault. Furthermore there are two LEDs (one yellow and one red) indicating fault
and alarm in the central unit. Finally there are two green LEDs that are used for
service purposes.
4. Address switch
With the DIP switch the 8-bit address of the LPK is set.
5. Real time clock
The real time clock is keeping track of the time in the system. The clock has
built-in registers for seconds, minutes, hours, days, week-day, month and year
(including leap-years). The real time clock is reset from the control panel.
6. Internal communication loop (RS485)
The internal communication loop is connected to all SPKs in the same rack
system. All SPKs are polled and supervised via this loop.
7. Loop switch
The loop switch changes the communication channel from one external loop to
the other.
8. System communication loop (RS422)
This block contains the communication with control units and other central
units.
9. Data/address buffers
All bus connections going from the back plane are buffered in special buffer
circuits.
10. Back plane signals
Certain hardware signals in the back plane are read by the LPK after a voltage
conversion.
11. Basic-alarm
The basic-alarm function is activated if a SPK or the LPK is faulty and therefore
incapable of transmitting an alarm. This board will block the basic-alarm
function if the processor is in proper working order.
12. Fire brigade output
Two relay outputs for connection to the fire brigade. The alarm relay is
programmable and the other relay is activated when there are not muted faults in
the system.


Technical data
Board size: Single Europe board, 100 x 160 mm.
Front panel: Anodised aluminium, width 6 TE (30.1 mm).
Ambient temperature: -10°C to +70°C.


Iin max: 120 mA.
Outputs: 2 relays, 480 mA, 125 V


Service manual CS3000 Chapter 3: Relay board ARK-2 3-14
Relay board ARK-2

General
Orders to the alarm devices and controls issued by the LPK is executed by the
relay board. The alarm device outputs can also be activated by a basic-alarm
via the back plane. Furthermore the relay board may be used for monitoring
external signals and for supervision of power supply to external units.
Handling
Indications
The LED on the front panel of the board is lit every time the board is polled.
F1 F2 Fuses
F3 F4
There are 14 fuses on the front panel..
F5 F6
F1 Output 24 VDC 1+ F2 Output 24 VDC 1-

F7 F8
F3 Output 24 VDC 2+ F4 Output 24 VDC 2-
F9 F10
F5 Alarm bell output 1+ F6 Alarm bell output 1-
F11 F12
F13 F14
F11 Relay output RL1 F12 Relay output RL2
F13 Relay output RL3 F14 GA-output
Salwico ARK-2
Fuse rating: 2 AT 5x20 mm


Jumper "PLUS"
With this jumper the pulse type can be altered. In the left position the pulse is
internally generated, in the right position the pulse comes from an external
source.
Switch S9
This switch is found on the front panel and is used for resetting the basic-
alarm.
Switch SW1
SW1-1, SW1-2, SW1-3 (B1, B2, B3)
"ON" : Steady signal to corresponding alarm bell output.
"OFF": Pulsed signal to corresponding alarm bell output.
SW1-4, SW1-5, SW1-6 (R1, R2, R3)

"ON" : Steady signal to the outputs of relays RL1-RL3.
"OFF": Pulsed signal to the outputs of relays RL1-RL3.
SW1-7 (GA)
"ON" : Signal in step with the signal on the GA-input.
"OFF": Pulsing signal
Replacing the board
To replace the ARK-2 follow these steps:
1. Shut down the central by removing the fuses F3-F6 on the KE-2 rectifier.
WARNING!

3. Start up the central by inserting F3+F4 and F5+F6 in that order.


Function
Block diagram
BACK PLANE
PTC
ALARM DEVICE 5
2 FUSE
DC/ DC FAULT BARRIER
CONVERTER
POWER SUPPLY 6
FUSE
FAULT BARRIER
FAULT
1 DET.
7
RELAY OUTPUT
3
PANEL CONTROL
LED SIGNALS 8
FIRE/ FAULT
PTC
OUTPUT
9 11
GA - RELAY
EPLD/ PI OUTPUT
GA
LOGIC
4 GA INPUT 12
PANEL GA INTERM. INPUT 13
SWITCH
10
DIP
SWITCH
EXT. FUSE FAULT 14
BASIC ALARM INPUT 15
16
OPTO ISOL.
uP BUS 17


1. EPLD/PIO
The EPLD/PIO includes I/O-circuit to the microprocessor and a programmable
circuit for all output, input and supervising functions on the board.
2. DC/DC-converter
The DC/DC-circuit converts the battery voltage of the back plane to 5 VDC,
which is fed to circuits on the board.
3. Panel-LED
The panel-LED is flashing when the board is being polled by the LPK.
4. Panel-switch
The panel-switch is used for manually resetting the alarm devices after a basic-
alarm.
5. Alarm device output
Three programmable, fused and fault-supervised alarm device outputs.
6. Power supply output
Two fused and fault supervised outputs for power supply to external devices.
7. Relay output
Three programmable, fused and potential free relay outputs.
8. Fire/fault output
One current-sinking programmable output for FIRE and one for FAULT.
9. GA-logic
The GA-logic controls the GA-output and the alarm device outputs depending
on the GA-input and pulsed output selection.
10. DIP-switch
The DIP-switch is used for setting a continuous/intermittent function of the
outputs 5 and 7 above.
11. GA-relay output
One fused and potential free relay output, which follows the GA-input.
12. GA-input
Input for connection of GA push button.
13. GA intermittent signal output
Input for connection of external intermittent signal for the GA.
14. External fuse fault input
Input for indication of fuse fault in external devices.
15. BASIC-ALARM input
Four opto-isolated inputs for external signals.
17. Micro processor bus
Connection of micro processor bus to the LPK.


Technical data
Board size: Two joined single Europe board, 100 x 160 mm.
Ambient temperature: -10° to +70°C.
Iin max: 80 mA.
Inputs
Four opto isolated with common +
Input voltage: Uin max: 35 VDC
Input current Iin : 8 mA at Uin = 24 V
OneDG, 2880 ohm relay coil for 24 VDC, activated when low
Activation of relay: Uactmax: 7.2 VDC
One external intermittence, 10 kohm pull-up to +24 V, activated when low
One external fuse fault, 10 kohm pull-up to +24 V, activated when low
Outputs
Two power outputs, 24 VDC, Imax : 2 A
Three fault supervised, programmable alarm outputs, 35 VAC, Imax : 2 A
Three change-over, programmable relay outputs, 35 VAC, Imax. : 2 A
One change-over relay output for GA, Imax. : 2 A
Two open-collector outputs, PTC-protected, one programmable and one
activated at not muted fault in the central unit, Umax. : 24 V, Isink max.: 100 mA


Service manual CS3000 Chapter 3: Input board INK-2 3-19
Input board INK-2

General
The input board INK-2 is used for getting information about external activities,
which can be used, for example, to control other outputs. The INK-2 board is
controlled by the alarm processor board LPK-2, via the address and data buses
in the back plane. The board also contains a status register for functional
checks.
The INK-2 board is equipped with 24 opto-isolated inputs for 24 VDC/10 mA.
These inputs are divided into six groups, each with four inputs with a common
return conductor.
Handling
Indications
There are two LEDs on the front panel of the board.
1 2 No 1 (green) when lit: proper voltage supply.

No 2 (green) when lit: the board is properly polled.
Fuse
The battery voltage is fused. If the fuse is blown a signal is activated in the
back plane. The fuse is accessible on the front panel of the board, and can be
used for disconnecting the power.
Fuse rating: 250 mAT 5x20 mm
Setting the address
Salwico INK-2 The address of the board is set with a DIP-switch (SW1), with 8 switches. The
address bits #2 - #9 are set. Bit #2 is set with SW1-1, and bit #9 with SW1-8.
For more information see Appendix A.
Replacing the board
To replace INK-2 follow these steps:
WARNING!



Function
Block diagram
BACK PLANE
1 2
+5V
DC/DC
CONVERTER
FUSE FAULT
SUPERVISION
POWER FAULT
4 5
3 ADDRESS BUS
LED CONTROL ADDRESS
INDICATOR LOGIC BUFFER
STATUS REGISTER
DATA
BUFFER
DATA BUS
8 8 8
INPUT BUFFER INPUT BUFFER INPUT BUFFER
9 9 9 9 9 9
4 OPTO- 4 OPTO- 4 OPTO- 4 OPTO- 4 OPTO- 4 OPTO-
ISOLATED ISOLATED ISOLATED ISOLATED ISOLATED ISOLATED
INPUTS INPUTS INPUTS INPUTS INPUTS INPUTS
INPUT CONNECTOR


1. DC/DC converter
which is supplied to all logical circuits on the board. Should the voltage
disappear, a signal is activated in the back plane.
2. Supervision
3. LED indications
On the front panel are two green LEDs for indicating 5V power and normal
polling.
4. Control logic
The control logic is used for decoding the address bus and for generating
signals to read/write the status register and read the input buffers.
5. & 6. Buffers
The address bus, the data bus and the control signals are buffered before
entering the board.
7. Status register
The status register is a read/write register. On reset the status is zeroed. Thus it
is possible to check the function of the board.
8. Input buffers
The signals on the inputs are buffered before entering the data bus.
The inputs are divided into six groups, where each group has a common return
conductor. The inputs are protected by transient suppressors. Each input is
equipped with an LED that is lit when the input is active. These LEDs are not
visible from the front panel.


Technical data
Board size: Single Europe board, 100 x 160 mm.


Iin max: 40 mA.
Inputs
24 opto isolated, transient protected in six groups with common return
conductor.
Input voltage: Uin max: 35 VDC.
Input current: Iin : 10 mA at Uin = 24 V.
Activated input: Iin min: 1.3 mA
Deactivated input: Iin max: 0.1 mA


Service manual CS3000 Chapter 3: Output board UTK-2 3-23
Output board UTK-2

General
The output board UTK-2 is used for controlling external relays, e.g. for fans
and fire doors. The UTK-2 board is controlled by the alarm processor board
LPK-2, via the address and data buses in the back plane.
The UTK-2 board is equipped with 24 opto-isolated outputs for 24 VDC/50
mA. The outputs are divided into six groups where each group includes four
outputs and a common positive conductor.
Handling
Indications
In the front panel of the board are two LEDs.
1 2 No 1 (green) when lit: proper voltage supply.

No 2 (green) when lit: the board is properly polled.
Fuse
back-plane. The fuse is accessible on the front panel of the board, and can be
Salwico UTK-2
Setting the address

The address of the board is set with a DIP-switch (SW1), with 8 switches. The
address bits #2 - #9 are set. Bit #2 is set with SW1-1, and bit #9 with SW1-8. For more information
see Appendix A.
Replacing the board
To replace the UTK-2 follow these steps:
WARNING!



Function
Block diagram
BACK PLANE
1 2
+5V
DC/DC
SUPERVISION
CONVERTER
FUSE FAULT
POWER FAULT
4
5
3
LED CONTROL ADDRESS
INDICATOR LOGIC BUFFER
10
STATUS REGISTER
DATA
CONTROL BUS
BUFFER
DATA BUS
7 8 7 8 7 8
OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT OUTPUT
STATUS LATCH STATUS LATCH STATUS LATCH
9 9 9 9 9 9
4 OPTO- 4 OPTO- 4 OPTO- 4 OPTO- 4 OPTO- 4 OPTO-
ISOLATED ISOLATED ISOLATED ISOLATED ISOLATED ISOLATED
OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS OUTPUTS
OUTPUT CONNECTOR


1. DC/DC converter
disappear, a signal is activated in the back-plane.
2. Supervision
3. LED indications
On the front panel are two green LEDs for indicating 5V power and normal
polling.
4. Control logic
The control logic is used for decoding the address bus and for generating
selection signals for read buffers and output buffers.
5. & 6. Buffers
entering the board.
7. Output status
The value written to the outputs can be read, to check the function of the
board.
8. Output latch
The output latches also functions as drive circuits for the opto switches.
9. Opto-isolated outputs
The outputs are divided into six groups, where each group has a common
positive conductor. The load is connected between the output and ground.
Each output is protected by a varistor and a freewheel diode for inductive
loads.
Technical data
Board size: Single Europe board, 100x160 mm
Front panel: Anodised aluminium, width 6 TE (30.1 mm)
Ambient temperature: -10°C - +70°C

Current consumption: Iin nom : 15 mA
Iin max : 55 mA
Outputs
24 opto isolated, transient protected in six groups with common positive
conductor
Output voltage: Uout max: 35 VDC
Output current: Iout max: 50 mA
Voltage drop: Umax : 1.2 VDC @ 50 mA
Leakage current: Iout max: 3 mA @ 70 C


Jumpers
Choice of source/sink outputs

Each of the 24 outputs can be individually chosen for source or sink outputs by
means of the jumpers on the PCB (see picture above). The outputs on the PCB
are grouped, with four outputs in each group. Each output has two jumpers (i e
eight jumpers per group).
The jumpers are factory set (as in the picture) for source output on all lines.
SOURCE SINK
Output group configuration. 4 outputs per group


Service manual CS3000 Chapter 3: Interface board GSK-2 3-27
Interface board GSK-2

General
The interface board GSK-2 is used for connecting detector sections containing
conventional digital detectors. With this board it is possible to connect the
detectors from a C300 system to the CS3000 system. These detectors will
however not be addressable. To each GSK-2 board a maximum of four
detector sections may be connected. The detector sections are supervised for
cable breaks and it is also possible to disconnect smoke detectors on these
sections.
Handling
Indications
There are nine LEDs on the front panel of the board.
No 1 (green) when lit: proper voltage supply.
No 2 (red) when lit: fire alarm in section #1
No 3 (yellow) when lit: fault in section #1
1 No 4 (red) when lit: fire alarm in section #2
3
2
4 5
6 7 No 6 (red) when lit: fire alarm in section #3
8 9 No 7 (yellow) when lit: fault in section #3
No 8 (red) when lit: fire alarm in section #4
Fuse
Salwico GSK-2
Fuse rating: 2 AT 5x20 mm
Setting the addresses

The address of the first GSK-2 board is set to binary 1, the second GSK-2
board is set to binary 2, etc.



Replacing the board
To replace a board follow these steps:
WARNING!


Function
Block diagram
1 2
+5V
3 VOLTAGE STAB FUSE FAULT
AND
ADDRESS
SUPERVISION
SWITCH +12V
VOLTAGE FAULT
2 GENERAL FIRE/FAULT ALARM
4 5
IDA SECTION 1
8
7 FIRE,FAULT 9 10
TEST AND INHIBIT
AND STATUS LOGIC BARRIER
TRANSMITTER/ DETECTION
RECEIVER
OFF
SECTION 2
8
7 FIRE,FAULT 9 10
TEST AND INHIBIT
DETECTION
OFF
DIGITAL 16
OUTPUTS
CONTROL
LOGIC
D/A CONV. SECTION 3
8
2
7 FIRE,FAULT 9 10
2 TEST AND INHIBIT
ANALOG 2
DETECTION
INPUTS 2
OFF
6 SECTION 4
8
LED 8
MONITOR 7 FIRE,FAULT 9 10
TEST AND INHIBIT
DETECTION
OFF


1. Voltage stabiliser
The board has a local voltage stabiliser for 5 VDC power and 12 VDC power.
The 5 VDC is supplied to all logical circuits on the board. The presence of
both powers is indicated by an LED. If one of the voltages should disappear, a
signal is activated in the back-plane.
2. Supervision
3. Address switch
The address of the first section is set with this switch. The other three sections
automatically receive the next three consecutive addresses.
4. IDA
Alarm signals, fault signals and status information are collected by two IDA-
circuits, which communicate with the central unit. The IDA-circuits also
controls the sections.
5. Control logic
Alarms and faults are latched in the GSK-2 board and at reset from the control
unit the section is turned on and off again. Common fire alarms and cable
break fault signals are also generated in the GSK-2. The alarm and fault
signals are added which gives an analogue signal, enabling the IDA to give an
auto-alarm.
6. LED indications
Fire alarm and fault indication are indicated on the front panel by one LED
each per section.
7. Fire, fault and status detection
Fire alarms and faults are detected by two comparators. The signals are filtered
before reaching the comparators. The status signal is an analogue signal that is
used to indicate the status of the section, if it is "on", "off" or has disconnected
smoke detectors.
8. Test and inhibit logic
When the disconnect smoke detector function is activated the output voltage to
the sections is lowered to 12 VDC.
9. Electrical isolation
Each section can be electrical isolated from the central unit by a double relay.
10. Barrier
Each section output is protected against transients and hf-interference.


Technical data
Board size: Single Europe board, 100x160 mm.

Ambient humidity: 96% Hr.
Input power: Uin : 24 VDC (-20% -- + 25%).

Current consumption: Iin nom : 25 mA
Iin max : 70 mA.
Outputs
Four supervised for connection of sections with conventional digital detectors.
Output voltage: Uin : 24 VDC (-20% -- + 25%).
Output current: Iout : 2.4 mA at Uin = 24 V.
Fire alarm: Iout min: 17 mA
Broken connection: Iout max: 0.8 mA


Service manual CS3000 Chapter 3: Interface board RS232K-2 3-32
Interface board RS232K-2

General
The RS232K-2 is an addressable interface board used for connecting the
CS3000 system to external computers, modems, terminals, mimics, serial
printers, etc.
The board is equipped with two RS232 channels and two RS485 channels.
One of the RS232 channels is accessible through a D-sub header on the front
panel and the other channels are connected via the back-plane.
The RS232K-2 is controlled by LPK-2 via the address and data buffers in the
back plane. All channels are programmable for baud-rate and other
communication parameters. The functions of the board are set by the definition
programme.
Handling
Indications
There are ten green LEDs on the front panel of the board.
No 1 when lit: proper voltage supply.
No 2 when lit: the board is properly polled.
No 3 when lit: RS232 channel #2 sending.
1 2 No 4 when lit: RS232 channel #2 receiving.
3 4
6
No 5 when lit: RS232 channel #2, RTS active.
5
7 8 No 6 when lit: RS232 channel #2, CTS active.
9 10 No 7 when lit: RS485 channel #1 sending.
No 8 when lit: RS485 channel #1 receiving.
Fuse
Salwico RS232K-2
Setting the address

The address of the board is set with a DIP-switch (SW1). The address bits #5 -
#9 are set. Bit #5 is set with SW1-4. The address of each RS232K-2 board is
set according to the definition in the Definition program. For more information
see Appendix A.



Replacing the board
To replace the RS232K-2 follow these steps:
WARNING!



Function
Block diagram
BACK PLANE
1 2
+5V
DC/DC
CONVERTER
FUSE FAULT
SUPERVISION
POWER FAULT
4 5 ADDRESS BUS
CONTROL ADDRESS
LOGIC BUFFER
6
DATA BUS
DATA
BUFFER
7 8
STATUS REGISTER STATUS REGISTER
UART UART UART UART

3
15 IRQ
LED
INDICATOR
9 10 12 13
232 232 485 485
14
14
11


1. DC/DC converter
disappear, a signal is activated in the back-plane.
2. Supervision
3. LED Indications
The 5 V voltage and proper polling are indicated by green LEDs. Send and
receive for both the RS485 channels as well as send and receive and two
control signals for one of the RS232 channels are also indicated by green
LEDs.
4. Control logic
The address bus is decoded and selection signals for the two double serial
channels are generated.
5. & 6. Buffers
entering the board.
7. & 8. DUART circuits
Two of the DUARTs are for the RS232 channels and two is for the RS485
channels. All parameters, such as baud-rate, parity, etc., are programmable.
9. & 10. RS232 adaptation
Adaptations of the signals from 5 V logic to RS232 logic and vice versa. The
signals from one channel are connected to a D-sub header on the front panel
and the other are connected to the back plane.
11. RS232 D-SUB HEADER
Male 9-pin D-sub header on the front panel with IBM PC/AT pin-standard.
signals from both channels are connected to the back plane.
14. Line protection
The line protector includes resistors for level definition of the line when not in
use. Line protection with zener diodes and varistors.


Technical data


Input power: Uin : 24 VDC (-20% - +25%)

Current consumption: Iin nom: 10 mA @ 24 V
Iin max: 40 mA @ 24 V


Service manual CS3000 Chapter 3: Interface board KPK-2 3-37
Interface board KPK-2

General
The KPK-2 is an addressable interface board used for connecting the CS3000
system to external computers, modems, terminals, mimics, serial printers, etc.
The board is equipped with two RS232 channels and two RS485 channels.
One of the RS232 channels is accessible through a D-sub header on the front
panel and the other channels are connected via the back-plane.
The KPK-2 is controlled by LPK-2 via the address and data buffers in the back
plane. All channels are programmable for baud-rate and other communication
parameters. The functions of the board are set by the definition programme.
Handling
Indications
There are ten green LEDs on the front panel of the board.
No 1 when lit: proper voltage supply.
No 2 when lit: the board is properly polled.
1 2 No 4 when lit: RS232 channel #1 receiving.
3 4
6
No 5 when lit: RS232 channel #2, sending.
5
7 8 No 6 when lit: RS232 channel #2, receiving.
9 10 No 7 when lit: RS485 channel #1 sending.
Fuse
Salwico KPK-2
Setting the address
The address of the board is set with a DIP-switch (SW1), two switches. The
recommended address and DIP-switch setting are provided in Appendix A.



Replacing the board
To replace the KPK-2 follow these steps:
WARNING!



Function
Block diagram


1. DC/DC converter
disappear, a signal is activated in the back-plane. The DC/DC converter aslso
supplies the serial port drivers with electric isolated power.
2. CPU/Memory/Watch-dog
Contains processor, memory, watch-dog and digital circuitry to provide system
function.
3. LED Indications
The 5 V voltage and proper polling are indicated by green LEDs. Send and
receive for both the RS485 channels as well as send and receive for the RS232
channels are also indicated by green LEDs. The serial channels can also be
enabled/disabled by the CPU.
4. DUART circuits
Two of the DUARTs are for the RS232 channels and two is for the RS485
channels. All parameters, such as baud-rate, parity, etc., are programmable.
Contains processor two serial ports which is connected to the RS485
tranceivers. The DUART also control certain I/O on the board.
5. Fuse fault
signals from one channel are connected to a D-sub header on the front panel
and the other are connected to the back plane.
signals from both channels are connected to the back plane.
10. & 11. Buffers
entering the board.
12. Board address
Selects the board address.
13. RS232 D-SUB HEADER
Male 9-pin D-sub header on the front panel with IBM PC/AT pin-standard.


Technical data


Input voltage: Uin : 24 VDC (-20% - +25%)

Current consumption: Iin nom: 25 mA @ 24 V
Iin max: 25 mA @ 24 V


Service manual CS3000 Chapter 3: Rack CSR-3200 3-42
Rack CSR-3200
General
All PCBs in the central unit are mounted in a rack with a back plane. The back
plane supplies all the PCBs with power and channels for communication
between them. The rack has room for 14 PCBs. If needed, several racks can be
inter-connected. The rack fits into a standard 19" cabinet.
Handling
Reserved PCB locations
Certain slots in the rack are reserved for special purposes.
The relay board ARK-2 must be placed in slot #1 of the first rack and is the
only board allowed in this slot. If there are more than one rack inter-connected,
slot #1 in the other racks must be empty.
The alarm processor board LPK-2 must be placed in slot #2 of the first rack
and all boards communicating with the LPK-2 via the address and data bus
must be in the same rack. If there are more than one rack inter-connected, slot
#2 in the other racks may be used for other purposes.
If the interface board GSK-2 is used it may be placed in any available slot,
with the above exceptions. In this case a loop processor board SPK-2 must be
placed in the last slot (#14) of one of the racks.
Settings
The only necessary setting on the rack is made when an interface board GSK-2
shall be used for the connection of sections with conventional digital detectors.
In this case a SPK-2 board in slot #14 will be using the internal IDA-loop, and
therefore the two jumpers S01 and S02 must be set in their upper positions.
These two jumpers are normally set in their lower positions by the factory.
Function
Each board occupies 30 mm of the width of the rack. The slots in each rack are
numbered #1 - #14.
If more than one rack shall be inter-connected, this is done with flat cables
connected to headers on the rear side of the racks.
In order to prevent noise from loads connected to the relay board ARK-2 from
interfering with other boards, the power to the rack is divided in two separate
channels, one supplying the relay board and one for the rest of the rack.


Service manual CS3000 Chapter 3: Rack CSR-3200 3-43
Technical data
Type: Standard 19"
Height: 4 U (177 mm)
Depth: 215 mm
Number of slots: 14, each 6 TE width (30.1 mm)
Ambient temperature: -10°C -- +70°C
Humidity: 96 % Rh
Input power: Unom : 24 VDC (-20% -- + 25%)


Service manual CS3000 Chapter 3: Power unit KE-2 3-44
Power unit KE-2

General
The power unit KE-2 supplies the fire alarm system with the necessary power,
either from mains, from batteries or from an other emergency source.
The power unit is under continuos supervision and controlled by the central
unit, which controls voltages, currents and certain faults. Important status data
are indicated by LEDs.
The KE-2 battery has a programmable charging characteristic consisting of
five different charging phases: soft start, constant current, constant voltage,
equalisation and maintenance charging.
Indications
There are seven LEDs on the front panel of the power unit.
LED no. Colour Function

1 Green Mains voltage
2 Green Emergency voltage
3 Green: Rapid charge
4 Yellow General fault indication
5 Yellow Battery fault
6 Yellow Mains/emergency fault
7 Yellow Earth fault indication


Fuses
There are six fuses on the front panel.
Fuse Function Rating

no.
F1 Auxilary output 4 AT 6,3 x 32 mm
F2 Auxilary output 4 AT 6,3 x 32 mm
F3 Battery fuse + 16 AT 6,3 x 32 mm
F4 Battery fuse - 16 AT 6,3 x 32 mm
F5 Net fuse 4 AT 6,3 x 32 mm
F6 Net fuse 4 AT 6,3 x 32 mm
WARNING!
When starting up the central first insert fuses F3+F4, and then F5+F6
in that order.


Technical data
Mains/emergency voltage: 230 V +10%/-15%
Mains/emergency frequence: 50-60 Hz
Output current : Imin: 0.1 A
Imax: 20 A*
Output voltage: Uout: 23 - 26 VDC
Urip: ± 0.2 VDC
*
Output current is of higher priority than battery charging current. If the
output current exceeds 8 A the battery charging current will decrease. The
battery charging current is equal to zero when the output current is equal to
20 A.
Battery charging
Charging current: Icharge: 0 - 10 A**
Charging voltage: Ucharge: 21.5 - 34.0 ± 0.2 VDC
**
The charging current and the charging voltage can be set individually for
the different charging phases. The charging current can be set between 0-10
A and the charging voltage can be set between 21 - 34 VDC.


Service Manual CS3000 Appendix A: DIP switch settings A-1
DIP switch swttings
Appendix A: DIP switch settings

The addresses of the following boards, the INK-2, RS232K-2, KPK-2 and UTK-2, are
set with a DIP switch. The setting of the DIP switches and the corresponding
hexadecimal addresses are listed below.
The address set on the DIP sitch must correspond to the address specified in the
Definition program .
INK-2
Address Hex.
CC
RS232K-2 board 1
Address Hex.
E0
RS232K-2 board 2
Address Hex.
80
UTK-2 board 1
Address Hex.
B0
UTK-2 board 2
Address Hex.
B4


Service Manual CS3000 Appendix A: DIP switch settings A-2
DIP switch swttings
UTK-2 board 3
Address Hex.
B8
UTK-2 board 4
Address Hex.
BC
UTK-2 board 5
Address Hex.
C4
UTK-2 board 6
Address Hex.
C8
KPK-4 board 1
ON Address Hex.
100
KPK-4 board 2
ON Address Hex.
200


Service Manual CS3000 Appendix B: Fault codes B-1
Fault codes
Appendix B: Fault codes CS3000 version 4

All the fault codes, their cause and how an operator with some knowledge of the
system can solve the problem, are listed below. When a fault occurs, localise the
problem and deal with it.
The word FAULT is displayed on the first line of the display together with a fault
code followed by the section number and the address for the section unit causing the
problem, if the system has this information. Additional text is displayed on line two, if
provided. A few fault codes can not be displayed with all this information. These fault
codes are marked with an asterisk (*) in the summary below.
1 CONTROL UNIT MISSING

The central unit is missing a control unit after cold start.
Cause Remedy
System loop break. Mend the cable.

Control unit incorrectly Check and readdress the control
addressed. unit.
Hardware fault in the control Exchange the unit.
unit.
Wrong number of control units Check the specification and
in the definition. redefine the system.
2 ADDITIONAL CONTROL UNIT

An additional control unit is found by the central unit after cold start.
Cause Remedy
Wrong definition of number of Check the specification and

control units. redefine the system.
3 MISSING CENTRAL UNIT

The main central unit is missing a sub-central after cold start.
Cause Remedy
LPK-2 in a central unit is Set a valid address.

incorrectly addressed.
LPK-2 has a hardware fault. Exchange the board.
repeater panels. redefine the system.


Fault codes
4 ADDITIONAL CENTRAL UNIT

An additional sub-central is found by the central unit after cold start.
Cause Remedy

central units. redefine the system.
5 SECTION(S) MISSING
The main central unit is missing a section after cold start.
Cause Remedy
SPK-2 or LPK-2 has a hardware Exchange the board.

fault.
sections. redefine the system.
6 ADDITIONAL SECTION(S)
An additional section has been found by the central unit after cold start.
Cause Remedy

sections. redefine the system.
7 MISSING SECTION UNIT(S)

Fewer section units has been found than defined in the loop.
Cause Remedy

section units. redefine the system.
Section unit connections faulty. Connect the unit correctly
Missing answer from a section Exchange the unit.
unit.
8 ADDITIONAL SECTION UNIT(S)

More section units have been found than defined in the loop.
Cause Remedy
Wrong definition of number of Compare the installation with the

section units. drawings. Redefine the system.
Section unit connections faulty. Connect the unit correctly.


Fault codes
21 BAD ANSWER (Abnormal condition)

Bad communication with one section unit or several section units, could be
temporary. This fault code is sent when an interference in the communication is
detected.
Cause Remedy
Bad communication with one or Exchange the section unit if the

several section units. condition remains or returns.
22 NO ANSWER
No polling answer from a section unit.
Cause Remedy
Wrong type of section unit. Exchange to the correct section

unit.
Two section units have the same Check the units.
address.
Hardware fault Exchange the unit.
A fuse is blown. A secondary Exchange the fuse.
fault appears, code (83).
Cable break in a loop or system Mend the cable. See Cable break
loop. A secondary fault at the end of this chapter.
APPEARS, code (121).
24 WRONG STATUS
Incorrect answer from the section unit.
Cause Remedy
Section unit faulty Exchange the section unit.
25 WRONG ID
The software does not recognise the ID of a section unit.
Cause Remedy
Section unit faulty. Exchange the section unit.

Wrong software in CS3000. Exchange the software.
Wrong type of detector has been Install the correct type of detector.
installed. Restart the system.


Fault codes
26 BAD COMMUNICATION IN A LOOP (Abnormal condition)

Bad communication in a loop.
Cause Remedy
Noisy environment. Test the loop. Measure the cable

resistance. See Cable break at the
end of this chapter.
41 SECTION BOOTING
A section in the system has generated a boot signal.
Cause Remedy
The system is booting. Which Reset the fault.

PCB that is booting is shown in
the display.
42 BOOT DISABLED
A section unit was disconnected by the system during the initialisation.
Cause Remedy
Section unit faulty. Exchange the section unit.

Address unit on a sub-loop is Test the sub-loop.
faulty.
43 WRONG ADDRESS INTERVAL

The section unit address interval set for a timer is wrong.
Cause Remedy
Overlapping address intervals. Set a valid address interval.

End-address of the interval is Set a valid address interval.
lower then the start-address.
61 MEMORY CKECKSUM ERROR

Data in memoryhas been unintensionally damaged.
Cause Remedy
Error in RAM or EPROM. Restart. If the fault returns

exchange the unit.


Fault codes
62 DEFINITION DATA ERROR

A fault has been discovered in the memory where the system definition is
stored.
Cause Remedy
Faulty LPK-2. Replace LPK.

Error in definition data. Download new definition data.
Wrong software version. Upgrade software version in
LPK.
64 LOOP POLL FAULT
Cause Remedy
The communication between the Localise the faulty unit and

loop units is interrupted either replace it. Localisation can be
because a hanging for more than done e.g. by interval-halving
20 seconds on a certain unit or technique.
because a polling cycle takes too
long time.
The fault can appear when a
command is given to set outputs
for a particular loop unit.
81 MAINS FAULT
Mains power failure.
Cause Remedy
Mains power missing. Attend to the problem.

Fuses are blown in the system. Exchange the fuses.
Cable break. Mend the cable. See Cable break
at the end of this chapter.
FAULT (81) 1 POWER MAINS FAULT

Mains power failure in the power unit.
83 FUSE FAULT
A fuse in the central unit is blown. Different messages are displayed depending
on the location of the fuse.
Cause Remedy
A fuse is blown. In the display is Exchange the fuse. See Fuses at

shown which fuse is blown. the end of this chapter.


Fault codes
84 VOLTAGE FAULT
Too low voltage in the system.
Cause Remedy
Internal voltage fault. Exchange the PCB.
85 I/O-FAULT
An I/O-board is faulty or missing.
Cause Remedy
Incorrect numbers of I/O-boards. Correct it.

One of the boards ARK-2, INK-2, Exchange the board.
UTK-2, RS232K-2 or KPK-2 is
faulty.
90 POLLUTED DETECTOR (Abnormal condition)
Cause Remedy
Detector head is polluted. Optical smoke detector: Clean the

detector head according to the
recommendations.
Ionization smoke detector:
Exchange the detector.
93 FUSE/CABLE FAULT
A fuse in the central unit is blown or there is a cable break. Different messages
are displayed depending on the location of the fuse.
Cause Remedy
A fuse is blown in the central Exchange the fuse. See Fuses at

unit. the end of this chapter.
FAULT (93) EXT.ALARM 9 FUSE/CABLE FAULT

A fuse blown or a cable break in external alarm device 9.
FAULT (93) BATTERY FUSE/CABLE FAULT

Battery fuse blown, cable break or bad battery in central unit.
101 ALARM FUNCTION FAILURE
Cause Remedy
The alarm function in the Exchange the detector.

detector does not work.


Fault codes
102 THERMISTOR FAULT
Cause Remedy
Thermistor in a heat detector Exchange the detector.

faulty.
103 ION SMOKE CHAMBER FAULT
Cause Remedy
Ion chamber in an ionization Exchange the detector.

detector faulty.
121 CABLE BREAK

Indicates that one of the system loops or a detector loop is faulty. Additional
fault codes can be NO ANSWER (22), MISSING REPEATER PANEL (1) or
CENTRAL UNIT MISSING (3).
Cause Remedy
One of the system loops, a Mend the cable. See Cable break
detector loop or a conventional at the end of this chapter.
loop is faulty.
FAULT (121) EXT.COMM 2 CABLE BREAK

The cable break is in system loop no 2. The fault can only be reset when the
central is allowed to communicate on the loop. This message can only emanate
from the central unit itself.
FAULT (121) SEC 1 CABLE BREAK

Cable break in detector loop. See also (125).
124 SUBLOOP CABLE BREAK
Cause Remedy
Cable break in sub-loop. Mend the cable. See Cable break

Missing end-of-line unit. Connect an end-of-line unit.
125 SHORT CIRCUIT ON LOOP

Short circuit in detector loop reported by a short circuit isolator. If more than
one short circuit isolator has given a fault message, the short circuit is situated
between them. The detectors between the short circuit isolators will give
messages of the type NO ANSWER (22). One message is always CABLE
BREAK (121), since the loop is broken. The short circuit faults must always be
reset before other faults.
Cause Remedy
Short circuit on detector loop See Short circuit at the end of this
chapter.

Fault codes
126 SHORT CIRCUIT ON PRIM. SIDE
Cause Remedy
Short circuit between the Attend to the problem.

positive and negative terminal on
the primary side.
127 SHORT CIRCUIT ON SEC. SIDE
Cause Remedy
Short circuit between the Attend to the problem.

positive and negative terminal on
the secondary side.
141 EARTH FAULT +
Cause Remedy
Earth fault between positive See Earth fault at the end of this
terminal and earth. chapter.
FAULT (141) POWER EARTH FAULT +

Earth fault to plus from the power unit.
142 EARTH FAULT-
Cause Remedy
Earth fault between negative See Earth fault at the end of this
terminal and earth. chapter.
FAULT (142) POWER EARTH FAULT -

Earth fault to minus from the power unit.
145 LOW VOLTAGE
Cause Remedy
Too low system voltage from the Test the rectifier and measure the
power unit. voltage.
Too low voltage: → Exchange the
rectifier.
Normal voltage: → Exchange the
IOK-4 board.


Fault codes
146 HIGH VOLTAGE (Abn. condition)
Cause Remedy
Too high system voltage from Test the rectifier and measure the
power unit. voltage.
Too high voltage: → Exchange the
rectifier.
Normal voltage: → Exchange the
IOK-4 board.


Fault codes
Cable break
No answer from any section unit
− The cable is broken before the first section unit on a single ended loop.
− The cable is broken before the first section unit at least once and it is also broken
after the last section unit, if the loop is a double ended loop.
Section units are answering

Look for the last section unit answering on each side of the loop. The cable
break is situated after or between these units.
Earth fault
• Check the earth fault circuit, change it if it is faulty.
• If the circuit is working properly, check the loops one by one.
• Disconnect the loops one by one, see Disconnection, Electric isolation of a loop.
Short circuit
No answer from any section unit
Search for the short circuit between the central unit and the short circuit
isolator.
Section units are answering

Search for the short circuit between the short circuits reporting the faults.
Proceed as follows when you want to locate an earth fault. Divide the cable in two
halves, locate the earth fault on one of the halves. Thereafter divide this part of the
cable into two halves. Continue to divide the cable into halves until you have found
the earth fault. If you are using a multimeter use the diode tester range.


Fault codes
Fuses
Check the fuses on the boards included in the system. The fuses are mounted on the
front panels on the following boards: ARK-2, GSK-2, INK-2, KPK-4, LPK-2,
RS232K-2, SPK-2 and UTK-2. The fuses to the IKK-4 are mounted on the board
itself.
Fault code Board Fuse Fuse rating

81 CSS3300 2A5 Net fuse 5 AT 5x20 mm
83 ARK-2 F1: Output 24 VDC 1+ 2A 5x20 mm
83 ARK-2 F2: Output 24 VDC 1- 2A 5x20 mm
83 GSK-2 Main fuse 2AT 5x20 mm
83 INK-2 Main fuse 250 mAT 5x20 mm
83 KPK-2 Main fuse 250 mAT 5x20 mm
83 LPK-2 Main fuse * 250 mAT 5x20 mm
83 RS232K-2 Main fuse 250 mAT 5x20 mm
83 SPK-2 Main fuse 1AT 5x20 mm
83 UTK-2 Main fuse 250 mAT 5x20 mm
93 ARK-2 F5: Alarm bell output 1+ 2A 5x20 mm
93 ARK-2 F6: Alarm bell output 1- 2A 5x20 mm
93 CSS3300 F4: Battery fuse 10AT 6,3x32 mm
Not supervised ARK-2 F11: Relay output RL1 2A 5x20 mm
Not supervised ARK-2 F14: GA-output 2A 5x20 mm
Not supervised IKK-4 F1: Control unit panel 500 mAT 5x20 mm
Not supervised IKK-4 F2: Main fuse 100 mAT 5x20 mm
Not supervised IKK-4 F3: Main fuse for F4-F5 500 mAT 5x20 mm
Not supervised IKK-4 F4: Power supply ext. device 315 mAT 5x20 mm
Not supervised IKK-4 F5: Power supply 315 mAT 5x20 mm
* The central unit is not working properly. Indicator No. 1 (green) is not lit.


Service manual Appendix C: Fault codes C-1
CS3000
Appendix C: Fault codes CS3000 version 6

Listed below are all fault codes, their causes and how an operator with some
knowledge of the system can solve the problem. When a fault occurs, localise
the problem and deal with it.
The word FAULT is displayed on the first line of the display together with a
fault code, followed by the zone number and the address for the loop unit
causing the problem, if the system has this information. Additional text is
displayed on line two, if provided. A few fault codes cannot be displayed with
all this information. These fault codes are marked with an asterisk (*) in the
summary below.
FIRE IN SYSTEM
There is a fire alarm in the system and the LPK board is not answering.
1 MISSING CONTROL UNIT

The central unit is missing a control unit after cold start.
Cause Remedy

Control unit incorrectly addresses. Check and readdress the control
unit.
Hardware fault in the control unit. Exchange the unit.
Wrong number of control units in the Check the specification and
definition. redefine the system.
2 ADDITIONAL CONTROL UNIT

The central unit found an additional control unit after cold start.
Cause Remedy
Wrong definition of number of control Check the specification and

units. redefine the system.
3 MISSING CENTRAL
The main central unit is missing a sub-central after cold start.
Cause Remedy
LPK-2 in a central unit is incorrectly Set a valid address.

addressed.
LPK-2 has a hardware fault. Exchange the board.
Wrong definition of number of repeater Check the specification and
panels. redefine the system.

Prepared: 2002-10-01 BM

CS3000
4 ADDITIONAL CENTRAL
The central unit found an additional sub-central unit after cold start.
Cause Remedy
Wrong definition of number of central Check the specification and

units. redefine the system.
5 LOOP(S) MISSING
The main central unit is missing a loop after cold start.
Cause Remedy
SPK-2 or LPK-2 has a hardware fault. Exchange the board.

Wrong definition of number of loops. Check the specification and
redefine the system.
6 ADDITIONAL LOOP(S)
The central unit found an additional loop after cold start.
Cause Remedy
Wrong definition of number of loops. Check the specification and

7 MISSING LOOP UNIT

Fewer loop units have been found than defined in the loop.
Cause Remedy
Wrong definition of number of loop units. Check the specification and

Loop unit connections faulty. Connect the unit correctly
Missing answer from a loop unit. Exchange the unit.
8 ADDITIONAL LOOP UNIT(S)

More loop units have been found than defined in the loop.
Cause Remedy
Wrong definition of number of loop units. Check the specification and

Loop unit connections faulty. Connect the unit correctly.
11 LOOP MISSING DEF. DATA
Cause Remedy
The loop has not been defined properly at Redefine the loop.
the installation.


CS3000
12 SUBCENTRAL MISSING DEF. DATA
Cause Remedy
The sub-central has not been defined Define the sub-central.

properly at the installation.
13 WRONG TYPE OF CONTROL UNIT
Cause Remedy
Wrong definition at the installation of the Redefine the sub-central.

control unit.
21 BAD ANSWER (Abnormal condition)

Bad communication with one loop unit or several loop units, this could be
temporary. This fault code is sent when interference in the communication is
detected.
Cause Remedy
Bad communication with one or several Exchange the loop unit if the
loop units. condition remains or returns.
22 NO ANSWER
The loop unit doesn't answer.
Cause Remedy
Wrong type of section unit. Exchange to the correct section

unit.
Two loop units have the same address. Check the units.
Hardware fault Exchange the unit.
A fuse is blown. A secondary fault Exchange the fuse.
appears, code (83).
Cable break in a loop or system loop. A Mend the cable. See Cable break
secondary fault APPEARS, code (121). at the end of this chapter.
24 WRONG IDA STATUS

Incorrect answer from the loop unit.
Cause Remedy
Loop unit faulty Exchange the loop unit.


CS3000
25 UNKNOWN ID
The software does not recognise the ID of a loop unit.
Cause Remedy
Loop unit faulty. Exchange the loop unit.

Wrong software in CS3000. Exchange the software.
Wrong type of detector has been installed. Install the correct type of detector.
Restart the system.
26 BAD LOOP COMM (Abnormal condition)

Bad communication in a loop.
Cause Remedy
Noisy environment. Test the loop. Measure the cable

resistance. See Cable break at the
27 LOOP COMM STOPPED

No communication in a loop.
Cause Remedy
A loop unit is faulty. Check and if necessary exchange

the loop unit.
28 LOOP TRANS. STOPPED

Loop communication stopped.
Cause Remedy
Loop modem cannot transmit. Turn off the power, wait for 5
minutes, then restart the system.
Faulty loop unit. Search for the faulty unit by
interval-halving and replace the
unit.
29 COMMUNICATION ERROR
A loop unit has sent a wrong checksum.
Cause Remedy
Two loop units have the same address. Check the addresses of the units
and set correct adresses.
Loop unit faulty. Exchange the unit.


CS3000
30 CONTROL UNIT X NO POLL FROM MAIN CENTRAL

There is no contact between control unit x and the main central unit.
Cause Remedy
The LPK in the main central unit is not The LPK is faulty. Replace it.
answering.
Cable break in the system loop. Check the cable.
41 BOOTED
A loop in the system has generated a boot signal.
Cause Remedy
The system is booting. Which PCB that is Reset the fault.

booting is shown in the display.
42 BOOT DISABLED
A loop unit was disconnected by the system during the initialisation.
Cause Remedy
Loop unit faulty. Exchange the section unit.

Address unit on a sub-loop is faulty. Test the sub-loop.
43 WRONG ADDRESS INTERVAL

The loop unit address interval set for a timer is wrong.
Cause Remedy
Overlapping address intervals. Set a valid address interval.

End-address of the interval is lower then Set a valid address interval.
the start-address.
44 ILLEGAL ADDRESS
The received address does not correspond with the sent address.
Cause Remedy
Loop unit faulty. Exchange the loop unit.
51 LOOP OUTPUT MISSING
Cause Remedy
The loop unit has no active outputs. Error Download new set-up data.
in the site set-up.


CS3000
61 MEMORY CHECKSUM ERROR

Data in memory has been unintentionally damaged.
Cause Remedy
Error in RAM or EPROM. Restart. If the fault returns

exchange the unit.
62 SETUP DATA ERROR

A fault has been discovered in the memory where the system definition is
stored.
Cause Remedy
Faulty LPK-2. Replace LPK.

Error in definition data. Download new definition data.
Wrong software version. Upgrade software version in LPK.
64 LOOP POLL FAULT
Cause Remedy
The communication between the loop units Localize the faulty unit and replace
is interrupted either because a hanging for it. Localization can be done e.g. by
more than 20 seconds on a certain unit or interval-halving technique.
because a polling cycle takes too long
time.
The fault can appear when a command is
given to set outputs for a particular loop
unit.
81 MAINS FAULT
Mains power failure.
Cause Remedy
Mains power missing. Attend to the problem.

Fuses are blown in the system. Exchange the fuses.
Example:
FAULT (81) 1 POWER MAINS FAULT
Mains power failure in the power unit.


CS3000
83 FUSE FAULT
A fuse in the central unit is blown. Different messages are displayed depending
on the location of the fuse.
Cause Remedy
A fuse is blown. In the display is shown Exchange the fuse. See Fuses at the
which fuse is blown. end of this chapter.
84 LOW VOLTAGE
Too low voltage in the system.
Cause Remedy
Internal voltage fault. Exchange the PCB.
85 I/O-FAULT
An I/O-board is faulty or missing.
Cause Remedy
Incorrect numbers of I/O-boards. Correct it.

One of the boards ARK-2, INK-2, UTK-2, Exchange the board.
RS232K-2 or KPK-2 is faulty.
90 POLLUTED DETECTOR (Abnormal condition)
Cause Remedy
Detector head is polluted. Optical smoke detector: Clean the

detector head according to the
recommendations.
Ionization smoke detector:
Exchange the detector.
93 FUSE/CABLE FAULT
A fuse in the central unit is blown or there is a cable break. Different messages
are displayed depending on the location of the fuse.
Cause Remedy
A fuse is blown in the central unit. Exchange the fuse. See Fuses at the
Cable break. Mend the cable. See Cable break at
the end of this chapter.
Example:
FAULT (93) EXT.ALARM 9 FUSE/CABLE FAULT
A fuse blown or a cable break in external alarm device 9.
FAULT (93) BATTERY FUSE/CABLE FAULT

Battery fuse blown, cable break or bad battery in central unit.


CS3000
96 BATTERY FUSE/CABLE FAULT

A battery fuse is blown in the central unit or a there is a cable break. Different
messages will be displayed depending on the cause of the problem.
Cause Remedy
A fuse is blown in the central unit. Exchange the fuse. See Fuses at
Cable break. Mend the cable. See Cable break at
101 ALARM FUNCTION FAILURE
Cause Remedy
The alarm function in the detector does not Exchange the detector.
work.
102 THERMISTOR FAULT
Cause Remedy
Thermistor in a heat detector faulty. Exchange the detector.
103 ION SMOKE CHAMBER FAULT
Cause Remedy
Ion chamber in an ionization detector Exchange the detector.

faulty.
121 CABLE BREAK

Indicates that one of the system loops or a detector loop is faulty. Additional
fault codes can be NO ANSWER (22), MISSING REPEATER PANEL (1) or
CENTRAL UNIT MISSING (3).
Cause Remedy
One of the system loops, a detector loop or Mend the cable. See Cable break at
a conventional loop is faulty. the end of this chapter.
Example:
FAULT (121) EXT.COMM 2 CABLE BREAK
The cable break is in system loop no 2. The fault can only be reset when the
central is allowed to communicate on the loop. This message can only emanate
from the central unit itself.
FAULT (121) SEC 1 CABLE BREAK

Cable break in detector loop. See also (125).


CS3000
124 SUBLOOP CABLE BREAK
Cause Remedy
Cable break in sub-loop. Mend the cable. See Cable break at

Missing end-of-line unit. Connect an end-of-line unit.
125 SHORT CIRCUIT

Short circuit in detector loop reported by a short circuit isolator. If more than one
short circuit isolator has given a fault message, the short circuit is situated
between them. The detectors between the short circuit isolators will give
messages of the type NO ANSWER (22). One message is always CABLE
BREAK (121), since the loop is broken. The short circuit faults must always be
reset before other faults.
Cause Remedy
Short circuit on detector loop See Short circuit at the end of this
chapter.
126 SHORT CIRCUIT ON PRIM. SIDE
Cause Remedy
Short circuit between the positive and Attend to the problem.

negative terminal on the primary side.
127 SHORT CIRCUIT ON SEC. SIDE
Cause Remedy
Short circuit between the positive and Attend to the problem.

negative terminal on the secondary side.
141 EARTH FAULT +
Cause Remedy
Earth fault between positive terminal and See Earth fault at the end of this
earth. chapter.
FAULT (141) POWER EARTH FAULT +

Earth fault to plus from the power unit.


CS3000
142 EARTH FAULT–
Cause Remedy
Earth fault between negative terminal and See Earth fault at the end of this
earth. chapter.
FAULT (142) POWER EARTH FAULT –

Earth fault to minus from the power unit.
145 LOW VOLTAGE
Cause Remedy
Too low system voltage from the power Test the rectifier and measure the
unit. voltage. If necessary exchange the
rectifier.
146 HIGH VOLTAGE (Abnormal. condition)
Cause Remedy
Too high system voltage from power unit. Test the rectifier and measure the
voltage. If necessary exchange the
rectifier.
147 FIRE PREWARNING
Cause Remedy
The system has detected a smoke value Check the unit.

approaching the alarm level.
150 TIMER STUCK
Cause Remedy
The timer does not work properly. Check the unit.
161 DOOR OPEN
Cause Remedy
A door is still open one minute after the Check the door.
instruction to close it was sent.
163 OPEN DOOR SUBLOOP BREAK
Cause Remedy
Cable break between module and open Mend the cable.

door sensor.


CS3000
164 DOOR CLOSED SUBLOOP BREAK
Cause Remedy
Cable break between module and closed Mend the cable.

door sensor.
166 DAMPER /DOOR SHOULD HAVE BEEN OPENED
Cause Remedy
Damper/door in wrong position. Check for obstruction.
167 DAMPER /DOOR SHOULD HAVE BEEN CLOSED
Cause Remedy
Damper/door in wrong position. Check for obstruction.
170 SENSOR FAULT

The detector is giving a too low analogue value.
Cause Remedy
The detector has a faulty sensor element. Replace the detector.

NB This fault could be the result of air Check the location of the detector
blowing at the unit. and if need be, move it to a less
windy location.
171 CABLE BREAK FROM INPUT 1
Cause Remedy
There is a cable break on input 1. Check the cable.
172 CABLE BREAK FROM INPUT 2
Cause Remedy
There is a cable break on input 2. Check the cable.
173 DOOR FEEDBACK
Cause Remedy
There is no response from the door- Check the door-holder relay and its
holding relay. cable.


CS3000
174 NO POWER SUPPLY FOR LOOP
Cause Remedy
No power feed from the pcb. DC/DC converter faulty.
175 DOOR IN WRONG POSITION
Cause Remedy
Door in wrong position. Check for obstruction.
176 CABLE BREAK POSITIVE SIDE
Cause Remedy
Check for a cable break on positive lead. Mend the cable break.
A tripped short circuit isolator can cause Check the short circuit isolators.
this fault.
177 CABLE BREAK NEGATIVE SIDE
Cause Remedy
Check for a cable break on negative lead. Mend the cable break.
A tripped short circuit isolator can cause Check the short circuit isolators.
this fault.
178 WRONG TYPE OF LOOP UNIT FOUND
Cause Remedy
Check the ID setting of the faulty unit. Set a correct value on the DIP-
switch of the unit.
179 UNABLE TO DETECT SHORT CIRCUIT
Cause Remedy
Unable to detect short circuit. Exchange loop-PCB.
180 SPRINKLER VALVE CLOSED
Cause Remedy
Sprinkler valve closed. Check why it is closed.


CS3000
181. SHORT CIRCUIT ON SUBLOOP
Cause Remedy
Short circuit on subloop. Check cable.
182 CABLE BREAK
Cause Remedy
A cable break has been detected. Check corresponding cables.
183 CABLE OVERLOAD, CURRENT LIMIT REACHED
Cause Remedy
There is an overload in the cable. Check if too many units are

connected to the cable. Compare
with cable data.
184 POWER FAULT
Cause Remedy
The power supply is lost. Check power generation.
185 LOSS OF CAPACITY TO CHARGE BATTERY
Cause Remedy
The battery charger is unable to charge the Check the battery charger and the
battery. battery.
186 EXTERNAL FAULT
Cause Remedy
Fault from input. Check cable and/or external unit.
187 DOUBLE ADDRESS ON LOOP
Cause Remedy
Check the offending units against Set correct addresses for the units,
drawings. with the DIP-switches.


CS3000
188 LOST CAPABILITY TO DETECT EARTH FAULT
Cause Remedy
Hardware fault. Exchange the unit.
Cable break
No answer from any loop unit
• The cable is broken before the first loop unit on a single ended loop.
• The cable is broken before the first loop unit at least once and it is also
broken after the last loop unit, if the loop is a double ended loop.
Loop units are answering

• Look for the last loop unit answering on each side of the loop. The cable
break is situated after or between these units.
Earth fault
• Check the earth fault circuit, change it if it is faulty.
• If the circuit is working properly, check the loops one by one.
• Disconnect the loops one by one, see Disconnection, Electric isolation of a
loop.
Short circuit
No answer from any loop unit
• Search for the short circuit between the central unit and the short circuit
isolator.
Loop units are answering

• Search for the short circuit between the short circuits reporting the faults.
Proceed as follows to locate an earth fault. Divide the cable in two halves and locate
the earth fault on one of the halves. Thereafter divide this part of the cable into two
halves. Continue dividing the cable into halves until the earth fault has been found. If
you are using a multimeter use the diode tester range.


CS3000
Fuses
Check the fuses on the boards included in the system. The fuses are mounted on the
front panels on the following boards: ARK-2, GSK-2, INK-2, KPK-4, LPK-2,
RS232K-2, SPK-2 and UTK-2. The fuses to the IKK-4 are mounted on the board
itself.

83 GSK-2 Main fuse 2AT 5x20 mm
83 INK-2 Main fuse 250 mAT 5x20 mm
83 KPK-2 Main fuse 250 mAT 5x20 mm
83 LPK-2 Main fuse * 250 mAT 5x20 mm
83 RS232K-2 Main fuse 250 mAT 5x20 mm
83 SPK-2 Main fuse 1AT 5x20 mm
83 UTK-2 Main fuse 250 mAT 5x20 mm
Not supervised ARK-2 F14: GA-output 2A 5x20 mm
Not supervised IKK-4 F1: Control unit panel 500 mAT 5x20 mm
Not supervised IKK-4 F2: Main fuse 100 mAT 5x20 mm
Not supervised IKK-4 F3: Main fuse for F4-F5 500 mAT 5x20 mm
Not supervised IKK-4 F4: Power supply ext. device 315 mAT 5x20 mm
Not supervised IKK-4 F5: Power supply 315 mAT 5x20 mm
* The central unit is not working properly. Indicator No. 1 (green) is not lit.

F5
F4
IKK-4 F1 GPK-4 500 mAT
F3
I/O-board IKK-4 F2 IKK-4 board 100 mAT
F2
(IKK-4) IKK-4 F3 Output devices 500 mAT
F1 IKK-4 F4 Voltage output 315 mAT
IKK-4 F5 Voltage output 315 mAT


CS3000 Service v6 E5 09 1 E

Uploaded by

Copyright:

Available Formats

CS3000 Service v6 E5 09 1 E

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CS3000 Service v6 E5 09 1 E

Uploaded by

Copyright:

Available Formats

Fire Alarm System

Edition 5, 09 1 E, August 2009.

© 2004-2009, Consilium Fire & Gas AB

Chapter 1: Control unit

Chapter 2: The circuit board of the control unit

Chapter 3: The circuit boards of the central unit

Appendix A. DIP switch settings ............................................................... A-1

Appendix B. Fault codes CS3000 version 4...................................... B-1

Appendix C. Fault codes CS3000 version 6..................................... C-1

Document no.: S-4-007.875/E

© 1995, Consilium Marine AB

About this manual

Document no.: S-4-007.875/E

© 1995, Consilium Marine AB

Chapter 1: Control unit

Bypass built-in short circuit isolators

Document no.: S-4-007.875/E

© 1995, Consilium Marine AB

Chapter 2: The circuit board of the control unit

Fuse Fuse rating Fault code

Document no.: S-4-007.875/E

© 1995, Consilium Marine AB

Document no.: S-4-007.875/E

© 1995, Consilium Marine AB

10. System loop barrier

12. Power supply output

13. Opto-isolated inputs

14. Opto-isolated outputs

Document no.: S-4-007.875/E

© 1995, Consilium Marine AB

Ambient temperature: -10°C - +70°C.

Input power: Uin : 24 VDC (-20% - + 25%).

Outputs: 4 opto-isolated sourcing outputs

Inputs: 4 opto- isolated inputs, active high

Document no.: S-4-007.875/E

© 1995, Consilium Marine AB

Chapter 3: The circuit boards of the central unit

Document no.: S-4-007.875/E

© 2002, Consilium Marine AB

2. Remove the board and replace it with the new board.

Document no.: S-4-007.875/E

© 2002, Consilium Marine AB

Document no.: S-4-007.875/E

© 2002, Consilium Marine AB

Document no.: S-4-007.875/E

© 2002, Consilium Marine AB

Block diagram Model 3

Document no.: S-4-007.875/E

© 2002, Consilium Marine AB

Document no.: S-4-007.875/E

© 2002, Consilium Marine AB

JP3 Normally strapped.

Document no.: S-4-007.875/E

© 2002, Consilium Marine AB

Technical data Model 1 & 2

Ambient temperature: -10°C to +70°C

Input power: Uin : 24 VDC (-20% - + 25%)

Output voltage: Uut : 30 VDC (+/- 5%)

Ambient temperature: -10°C to +70°C