Smart Direct Key Programming: Supervag Key - Application Sheet

SuperVAG KEY - application sheet
Professional diagnostic tool and Lockmisth solution for VAG cars (VW, Skoda,
Seat and Audi). SuperVAG brings solution for:
 Key Programming, now with Smart Direct Key programming - duplicate and add
your key just within a few seconds
 Remote programming including remote testing
 Solution for All Key Lost situation
NEW: Smart Direct Key

Programming
You may think that it is difficult to program keys. Especially on new cars after year 2009 with
immobiliser generation 6G. This cars have advanced immobiliser security system that contains pin,
component security and long key learning procedures that requires expensive key programmers to
precode key/transponders and unlock immobiliser. However, NOW with Smart Direct Key
Programming it cannot be easier if you have at least one working key. You can add more keys within
few minutes, just few clicks and no need of key programmer. All is done simply via OBD. All you need is
SuperVAG KEY and empty transponder.
Applicable to
Dashboards VDO UDS and Magneti Marelli 2009–2014
Supported models
USA & Canada
Volkswagen Jetta, Passat, Sportwagon, GTI, Tiguan
Latin America
Volkswagen Fox, Spacefox, Saveiro, Gol, Suran
Europe
Volkswagen Golf, Caddy, Polo, Touran, Transporter, Sharan
Seat Leon, Alhambra, Ibiza, Altea
Skoda Fabia, Roomster, Octavia, Superb
What you need

SuperVAG KEY
Empty transponder
At least one working key
1
Just simply follow this procedure
After year 2009 Volkswagen group introduced new transponder types with new key learning
procedures.
There are two options how to add keys to car:
precoding of transponder
or simple method SuperVAG Smart Direct Key Programming
What you need

SuperVAG KEY
Empty transponder
At least one working key
Direct Key Programming is the smart solution offered by SuperVAG Tool. With this method, you do
not need any key/transponder programmer. You just click Key learning/programming function and
enter required number of keys to be add. Program starts programming mode in dashboard and shows
data on the dashboard display number of learned keys and number of keys required to be learned (for
example 0–2. 0 keys learned, 2 keys required to learn).
NOTE: New keys will not be as clones. Every key is unique and have its own ID.
Step 1 - Start key programming
Picture#1 - Select car model and click on Key programming button
Picture #2 - Click on Key learning (no PIN needed) button
Step 2 - Set number of keys to learn and insert every key

into ignition
Press number of keys - program asks you how many keys you want to learn (total).It means all working
keys plus all new keys. Enter number of keys and press YES.
Step 3 - Insert every key into ignition

Turn it into position 2 (indicator goes on) and then remove key and continue with next key. You must do
this procedure with all keys you want to learn including original key you started with.
Step 4 - confirm all changes

Last step - keys are now learned. But program still keeps old data until you confirm changes. In this
step, first check that engine starts with every key. Than look at dashboard if you can see odometer
2
state/value. If you cannot see odometer state and there is still key counter for example 1–6 that mean
key learning was not successful and dashboard did not finish key programming mode - as you can see
on following picture.
Click on NO if something is not right, for example car does not start, and dashboard will be restored
into original state from saved data. Original key will work and will not be erased. Repeat the procedure
again.
Click on YES if everything is all right, car starts and you can see odometer state. Program will write
new keys into memory of dashboard.
DONE
When you have no working key, SuperVAG has easy and fast solution for All key lost situation too. You
do not need expensive programmer or to do any soldering. SuperVAG has developed special click-on
cables SVG149 and SVG157 to solve such a situation.
See section All key lost for more details.
All Key
Lost Solution
Procedure
If you are in the All Key Lost situation (with no working key), the data cannot be read. You must get
the instrument cluster into the Service mode all first using special designed clip-on cables SuperVAG
SVG 149 for NEC dashboards or SVG 157 for MICRONAS dashboards (without this device you cannot
continue).
After you finish All key lost procedure, dashboard is unlocked and you can get into programming mode
and start direct key programming.
Applicable to
Dashbards VDO UDS or Micronas 2009—2012
What you need

SuperVAG KEY license
SVG 149 for NEC dashboards
SVG 157 for Micronas dashboards
Empty transponder
Source +12 to power SVG cable cut out
Right key blade for lock
3
NOTE: For dashboards Magneti Marelli, there is possible to add key just with direct key
programming via OBD even without valid key.
Supported models
USA & Canada
Volkswagen Jetta, Passat, Sportwagon, GTI, Tiguan
Latin America
Volkswagen Fox, Spacefox, Saveiro, Gol, Suran
Europe
Volkswagen Golf, Caddy, Polo, Touran, Transporter, Sharan
Seat Leon, Alhambra, Ibiza, Altea
Skoda Fabia, Roomster, Octavia, Superb
Step 1 - Conditions and preparation

Car have no working key in ignition
If you have at least one working key, you can skip this procedure and go for Direct key programming
You have to dismount the instrument cluster from the car and remove the back cover
Connect special cable SVG 149 for dashboards NEC or SVG 157 for dashboards Micronas. Connect
this SuperVAG cable to the SuperVAG USB interface and power supply (12V)
Picture #3 - Clip-on cable SVG 149 for NEC dashboards
Picture #4 - Clip-on cable SVG 157 for MICRONAS dashboards
Step 2 - Start key programming
Picture #5 - Select car model and click on Key programming button
Picture #6 - Click on Key learning (no PIN needed) button
Step 3 - Start all key lost procedure

You do not have working key in ignition. Program tells you that you can continue only with connected
cable SVG 149 or SVG 157. Without this device you cannot continue.
Step 4 - Connect pogo pin

Now follow program instructions. Program tells you to turn switch on SVG cable to position 0. Display
goes OFF.
Picture #7- Than wait 10 seconds for dashboards to goes completly off.
4
There is the most important part. You must connect pogo pin to the right position on dashboard. Pogo
pin is part of SVG cable. You can find right position of pogo pin on our website. For better idea how it
works, you can see example of pogo pin position on photo.
Picture #8 - SuperVAG USB interface
Picture #9 - PIN positioning
Picture #10 - When pin is connected, turn power supply ON and press OK button.
DONE

Smart Direct Key Programming: Supervag Key - Application Sheet

Uploaded by

Copyright:

Available Formats

Smart Direct Key Programming: Supervag Key - Application Sheet

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Smart Direct Key Programming: Supervag Key - Application Sheet

Uploaded by

Copyright:

Available Formats

SuperVAG KEY - application sheet

NEW: Smart Direct Key

What you need

What you need

Step 1 - Start key programming

Picture#1 - Select car model and click on Key programming button

Picture #2 - Click on Key learning (no PIN needed) button

Step 2 - Set number of keys to learn and insert every key

Step 3 - Insert every key into ignition

Step 4 - confirm all changes

See section All key lost for more details.

What you need

Step 1 - Conditions and preparation

Picture #3 - Clip-on cable SVG 149 for NEC dashboards

Picture #4 - Clip-on cable SVG 157 for MICRONAS dashboards

Step 2 - Start key programming

Picture #5 - Select car model and click on Key programming button

Picture #6 - Click on Key learning (no PIN needed) button

Step 3 - Start all key lost procedure

Step 4 - Connect pogo pin

Picture #8 - SuperVAG USB interface

Picture #9 - PIN positioning

You might also like