AUTOMATIC TRANSFER SWITCH

CONTROLLERS ATL SERIES

 2 power sources automatic
transfer switch controllers
The automatic transfer switch controllers ATL 600 - ATL601 - ATL 610 - ATL 800
can supervise and manage the changeover between 2 three-phase power sources.
The voltage and frequency measurements are shown on the graphic LCD display and
the LEDs on the front panel provide a clear indication about the power source status.
Management of 2 power sources
Control of undervoltage, overvoltage, phase loss, asymmetry,
minimum and maximum frequency, with time delay and
independent enabling
Inputs, outputs, limits, counters and alarms are
programmable by the user
Power sources can be independently defined as
utility or generator
Automatic test management for standby and
rotation generators
Suitable for LV and MV systems
Programmable maintenance alarms
Suitable for contactors, motorised circuit breakers
and motorised changeover switches
Tie breaker management for ATL 800 only
Closed transition available for ATL 800 only
Customizable change-over devices layout and
For ATL 610 - ATL 800 only: transfer strategy for ATL 800 only
Dual AC/DC power supply Built-in PLC technology for ATL 800 only
Real time clock with backup energy Built-in NFC technology for ATL 800 only.
Expandability with EXP... modules (e.g. Ethernet, extra I/Os).

ATL 6... ATL 800 - Some possible configurations

Operational characteristics ATL 600 ATL 601 ATL 610 ATL 800
Power supply voltage 110-240VAC 12/24VDC 110-240VAC and 12/24VDC 110-240VAC and 12/24/48VDC
Voltage measurement inputs
• Rated voltage Ue 100-480VAC L-L 100-480VAC L-L 100-600VAC L-L
• Measurement range 50-576VAC L-L 50-576VAC L-L 50-720VAC L-L
• Frequency range 45...65Hz
Current inputs - - -
Programmable digital inputs 6 6 8
•Type of input Negative
Programmable relay outputs 7
5 with 1 normally open contact each (NO - SPST) rated 8A 250VAC
2 with 1 changeover contact each (NO/NC - SPDT) rated 8A 250VAC
Expandability - With EXP... modules (2 max.) With EXP... modules (3 max.)
RS485 port - With EXP 1012 Built-in
Real time clock - With EXP 1012 Built-in
Compatible software and APP , and APP , , and APP
Flush-mount housing 144x144mm 144x144mm 180x240mm
Degree of protection IP20 at rear. IP40 on front; IP20 at rear.
IP65 with EXP80 01 optional gasket IP65 on front

Certifications and compliance

Certifications obtained: Compliant with standards: IEC/EN 61010-1, IEC/EN 61010-2-030,
cULus, EAC, RCM. IEC/EN 61000-6-2, IEC/EN 61000-6-4, IEC/EN 60947-1,
IEC/EN 60947-6-1,UL508, CSA C22.2 n°14.
 3 power sources automatic
transfer switch controller
ATL 900 is an ATS controller with high performance. Specific functions are available for the
control of three power sources and three switching breakers. It is possible to use the
default logics for the changeover strategy or personalise them with the integrated PLC.
ATL 900 has four current inputs; with this feature, it can use measured power to define
new logics on the control of the power sources.
Management of 3 power sources and 3 changeover
devices plus 2 tie-breakers
Control of under and over-voltage, phase loss,
asymmetry, minimum and maximum frequency, each
with independent enabling and time delay
Inputs, outputs, limits, counters and alarms are
programmable by the user
Power sources can be independently defined as utility or
generator
Automatic test management for standby or rotation
generators
Suitable for LV and MV systems
Programmable maintenance alarms
Suitable for contactors, motorised circuit breakers and
motorised changeover switches
4 current inputs for the three phases and neutral
Closed transition available
Real time clock with backup energy Tie breaker management
Expandability with EXP... modules Built-in PLC technology
(e.g. Ethernet, extra I/Os). Built-in NFC technology
Dual AC/DC power supply
ATL 900 - Some possible configurations

Operational characteristics ATL 900

Power supply voltage 110-240VAC and 12/24/48VDC
Voltage measurement inputs
• Rated voltage Ue 100-600VAC L-L
• Measurement range 50-720VAC L-L
• Frequency range 45...65Hz
Current inputs 4 inputs (5A or 1A)
Programmable digital inputs 12
• Type of input Negative
Programmable relay outputs 3 with 1 normally open contact each (NO - SPST) rated 16A 250VAC
3 with 1 normally open contact each (NO - SPST) rated 8A 250VAC
4 with 1 changeover contact each (NO/NC - SPDT) rated 8A 250VAC
Expandability With EXP... modules (3 max.)
RS485 port Built-in
Real time clock Built-in
Compatible software , , and APP
Flush-mount housing 180x240mm
Degree of protection IP20 at rear.
IP65 on front

Certifications and compliance

Certifications obtained: Compliant with standards: IEC/EN 61010-1, IEC/EN 61010-2-030,
cULus, EAC, RCM. IEC/EN 61000-6-2, IEC/EN 61000-6-3, IEC/EN 60947-1,
IEC/EN 60947-6-1,UL508, CSA C22.2 n°14.
 Graphic LCD display and USB and Wi-Fi dongles Optical port
text in 5 or 8 languages Through the optical port, direct connection to a PC USB port (using CX 01 dongle) All the controllers are equipped with a front optical port to support programming
or via Wi-Fi (using CX 02 dongle) is allowed. through CX 01 dongle and to use the functionality of CX 02 Wi-Fi dongle.
The backlit graphic LCD display makes the user’s interface easy with benefits in bad
CX 02 dongle (Wi-Fi) can furthermore make: Advantages:
light conditions. The ATL 600, ATL 601, ATL 610 and ATL 800 have a 128x80 pixel
• Copy of the parameters • No need to remove power from the panel to connect to the controller
resolution display while the ATL 900 has a bigger one with 128x112 pixel resolution.
All parameters in the ATL can be saved in the CX 02 memory and if required loaded • Electrical safety (no electrical connection)
For ATL 600, ATL 601and ATL 610, the texts are available in 5 different languages:
on the same device again (backup function) or to a different one of the same type • IP54 guaranteed
English, Italian, French, Spanish and German; additional 3 languages are available for
(replication of the configuration). • Convenience of working on the front.
ATL 800 and ATL 900: Portuguese, Polish and Russian.
• Clone of the device settings
The new interface allows the user to clearly see in a simple way:
In addition to the copy of the parameters, the current values of the statistical data,
• System status
counters and events can be saved in memory as well, in order to fully replicate an Real time clock for
• Voltage and frequency measurements
ATL on another device of the same type or to restore the ATL to a previously saved
• Statistical data ATL 610, ATL 800 and ATL 900
state.
• Control thresholds
• Pop-up windows for alarms. The ATLs have a real time clock with integrated backup reserve energy so all events
are identified by the time stamp at which they occurred.

Maintenance counters
In the ATLs, there are two counters used for maintenance purposes; the first one used
to monitor the working hours and the second to count the number of breaker
operations. When the counters reach the set limits, the relative alarms trip. 4 current inputs
Plug-in modules
P for ATL900
Current inputs allow to monitor load power
Inputs, outputs, internal variables, demand and to define proper changeover
strategy.
counters Knowing the power demand of the system
The input and output functions are preconfigured with the most common settings and the rated power of the sources, the ATL
but the user can easily change the default configuration to adapt the controller to the 900 is able to select the best source
application needs. All inputs and outputs are configurable. available that can correctly supply the
There are four types of programmable internal variables: loads.
• Limit thresholds
• Remote-controlled variables
• User alarms
• Programmable counters Optical port
About enabled limits and counters, the user can find the relative pages, scrolling
them on the display.

Statistics and events

The controllers record statistics data available for the user to understand how the
system works. An internal cyclic memory records up to 100 events for ATL 600,
ATL 601 and ATL 610, 250 for ATL 800 and ATL 900, that provide useful information
about the history and know the performance of the system controlled.

Programmable PLC logic for

Expandability ATL 800 - ATL 900
(2 slots for ATL 610 - 3 slots for ATL 800-ATL 900) With PLC logic capability, programs can be made to combine internal status of the
APP controller variables with signals incoming from the field to activate outputs, define new
The configuration of the ATL in different installations can have many variants, for
example the types of communication (USB, RS485, Ethernet) or the number of inputs changeover actions and/or generate alarms.
and outputs required. ATLs support expandability by EXP... plug-in modules.
Since the expansion modules are common with other LOVATO Electric products, this
NFC for ATL 800 - ATL 900
saves on management cost and, above all, guarantees configuration flexibility at Wi-Fi dongle Parameter programming by smart devices (e.g. tablets and mobile phones) is now
installation time as well provides performance ease especially when the system is possible using NFC wireless technology.
already in operation. The following EXP modules are available:
• Digital inputs and outputs Plug-in GPRS/GSM modem for
• Analog inputs and outputs (for ATL 800 and ATL 900 only) ATL 800 - ATL 900
• USB, RS232, RS485, Ethernet and Profibus communication Dual AC/DC power supply for
• GPRS/GSM modem (for ATL 800 and ATL 900 only). y) By fitting the EXP10 15 expansion module, the controller is automatically equipped and
The module is automatically recognised
ATL 610, ATL 800 and ATL 900 configures a GSM/GPRS modem. This simplifies installation and wiring.
by the ATL when installed. The ATL controllers can cover all the power supply solutions required in the market. Once a data-enabled SIM card is inserted, alarm or event SMS, email messages and
The best and safest solution is AC and DC power supply used together: latest logged data can be transmitted by the controller to FTP servers.
LOVATO Electric ATLs can do it.
The controller is supplied by the available line and during the transfer, in absence Closed transition for ATL 800 -ATL 900
of the AC source, the controller is supplied by the battery using the DC inputs.
For applications which require “closed transition” change-over strategy,
Non-stop control!
ATL 800 - ATL 900 is programmable with specific functions both for spontaneous
The AC ensures the supply during the monitoring of the system and the DC ensures
syncronising or controlled syncronising.
supply continuity during the switching.
 App
CX 02 dongle is the access point to the ATL through the APP. Thanks to , one can:
• See all the ATL measurements on smartphones or tablets.
• Send commands, such as counters reset or enabling and disabling of ATL outputs.
• Set parameters, save a copy in a file and retrieve it in case of need; the file can be sent via email as well.
• See active user alarms.
• See the event list and save a copy.
APP is downloaded from Google Play Store or Apple iTunes.

PARAMETER SETTING MEASUREMENT VIEWING SEND COMMANDS ALARM VIEWING

App
Programming the parameters via tablet and smartphone
is now possible also through NFC wireless technology.
Bringing a smartphone or tablet with NFC connection
enabled close to the display of the ATL 800 or ATL 900
activates the APP and the controller connected is
recognised automatically. It will then be possible to modify
the parameters and program the ATL.

configuration and
remote control software
is a software that permits to:
• Transfer setup parameters from ATL
to PC or vice versa
• Read measurements
• See events and alarms
• Send commands.

supervision and energy management software

ATL 610, ATL 800 and ATL 900 are compatible
with the current version of .
Thanks to the communication expansion
modules, they can be immediately added to an
existing network without needing extra external
accessories. Serial and Ethernet communications
are supported. The Ethernet port is suitable to
work with both static IP and dynamic IP address
and the ATL network configuration is similar to
what is normally done for PCs.
HOW TO ORDER
Automatic transfer Order code Description
switch controllers For 2 power sources
ATL 100 Automatic transfer switch controller for 2 single phase power sources,
modular housing (3 modules), power supply 110/230VAC configurable
ATL 600 Automatic transfer switch controller with optical port for 2 power sources,
144x144mm, power supply 110-440VAC
ATL 601 Automatic transfer switch controller with optical port for 2 power sources,
144x144mm, power supply 12/24VDC
ATL 610 Automatic transfer switch controller with optical port for 2 power sources,
144x144mm, power supply 110-440VAC and 12/24VDC, expandable with EXP...
expansion modules
ATL 800 Automatic transfer switch controller with optical port for 2 power sources,
ATL 600 - ATL 601 - ATL 610 180x240mm, power supply 110-440 VAC and 12/24/48VDC, expandable with EXP...
expansion modules, built-in RS485
For 3 power sources
ATL 900 Automatic transfer switch controller with optical port for 3 power sources,
180x240mm, power supply 110-440 VAC and 12/24/48VDC, expandable with EXP...
expansion modules, built-in RS485, 3ph+N current inputs

Expansion modules Order code Description Expansion Order code Description

for ATL 610 - ATL 800 - Inputs and outputs modules for Inputs and outputs
ATL 900 EXP10 00 4 opto-isolated digital ATL 800 - ATL 900 EXP10 04 2 opto-isolated analog
inputs inputs
EXP10 01 4 opto-isolated static EXP10 05 2 opto-isolated analog
outputs outputs
EXP10 02 2 digital inputs and 2 static EXP10 15 GPRS/GSM modem
outputs, opto-isolated (antenna excluded;
EXP10...
EXP10 03 2 relay outputs rated 5A see CX 03 below)
250VAC
Communication Order code Description
EXP10 06 2 relay outputs rated 1.5A devices and
EXP10... CX 01 USB dongle for
440VAC AC-15
accessories PC − ATL connection,
EXP10 07 3 relay outputs rated 1.5A for programming, data
440VAC AC-15 download, diagnostics
EXP10 08 2 opto-isolated digital and firmware upgrade.
inputs and 2 relay outputs Complete with cable,
rated 5A 250VAC 1.8m long
Communication ports CX 01 CX 02 Wi-Fi dongle for
EXP10 10 Opto-isolated USB PC − ATL programming,
interface data download,
diagnostics and
EXP10 11 Opto-isolated RS232
cloning
interface
CX 03 GSM quad-band
EXP10 12 Opto-isolated RS485
CX 02 antenna IP67 (800/
interface
900/1800/1900MHz)
EXP10 13 Opto-isolated Ethernet for EXP10 15
interface with web server expansion module
function
EXP80 01 IP65 gasket seal for
EXP10 14 Opto-isolated Profibus-DP internal display frame
interface for ATL 6...

Dual power supply Order code Description

module ATL DPS1 For measurement and control of voltages present at supply inputs to power motorised
circuit breakers/changeover switches, modular housing (3 modules), power supply
110/230VAC configurable

ATL DPS1
 2 power sources modular automatic
transfer switch controller
ATL 100 is a single phase automatic transfer switch controller in a modular housing. ATL 100
monitors the 2 single phase voltage inputs and it connects to the output the line that is within
the limits. The 2 outputs can control contactors or motorized changeover switches to perform
the transfer
he transfe between
f r betw lines.
t een the line

Rated voltage value selectable between 110VAC and 230VAC

Minimum and maximum voltage tripping thresholds
2 single phase L+N inputs
L1 priority line
2 independent measuring circuits
Fault LED for abnormal conditions
Inputs and outputs status LEDs
Self diagnostic of internal circuit
Alarm relay output.

Operational characteristics – Priority line: L1 when both input values are – Modular housing, 3 modules
– Rated supply voltage: 110/230VAC within limits – Degree of protection: IP40 on front; IP20
configurable – Fixed delay time between line switching: at rear.
– Frequency: 50/60Hz 0.5 seconds
– Input voltage range: 80-300VAC – 4 status indication LEDs for voltage of Certifications and compliance
– Voltage tripping thresholds min / max: each line within limits, voltage present at Certifications obtained: EAC.
80% / 120% of preset value output, relay output anomaly Compliant with standards: IEC/EN 61010-1,
– 2 line inputs L1-L2: single phase, between – Mounting: on 35mm DIN rail IEC/EN 61010-2-030, IEC/EN 61000-6-2,
phase and neutral (IEC/EN 60715) or by screws using IEC/EN 61000-6-4, IEC/EN 60947-1, IEC/EN
extractible clips 60947-6-1.

Dual power supply module

ATL DPS1 is capable of measuring and controlling two auxiliary supply voltages at its inputs
designating the most ideal to connect to the output. It reduces the number of components
and improves installat
installation safety.
a ion saf
a
Rated voltage value selectable between 110VAC and 230VAC
Minimum and maximum voltage tripping thresholds
2 single phase L+N inputs
1 single phase L+N output
L1 priority line
2 independent measuring circuits
Digital thresholds independent from the supply voltage
Indicating LEDs for abnormal conditions and status of inputs and outputs
Inputs and outputs status LEDs
Output voltage monitoring
Self diagnostic of internal circuit
Alarm relay output.
Operational characteristics – Priority line: L1 when both input values are – Modular housing, 3 modules
PD 107 GB 06 19

– Rated
R d supply l voltage:
l 110/230VAC
/ VAC within limits – Degree of protection: IP40 on front; IP20
configurable – Fixed delay time between line switching: at rear.
– Frequency: 50/60Hz 0.5 seconds
– Input voltage range: 80-300VAC – 4 status indication LEDs for voltage of Certifications and compliance
– Voltage tripping thresholds min / max: each line within limits, voltage present at Certifications obtained: cULus, EAC, RCM.
80% / 120% of preset value output, relay output anomaly Compliant with standards: IEC/EN 61010-1,
– 2 line inputs L1-L2: single phase, between – Mounting: on 35mm DIN rail IEC/EN 61010-2-030, IEC/EN 61000-6-2,
phase and neutral (IEC/EN 60715) or by screws using IEC/EN 61000-6-4, IEC/EN 60947-1, IEC/EN
– Current output: 4A max extractible clips 60947-6-1.
The products described in this publication are subject to be revised or improved at any moment. Catalogue descriptions and details, such as technical and operational data, drawings, diagrams and instructions, etc., do not
have any contractual value. In addition, products should be installed and used by qualified personnel and in compliance with the regulations in force for electrical systems in order to avoid damages and safety hazards.