Sharp 21GFx10L

21G-FX10L
SERVICE MANUAL
S9914021GFX10L
COLOUR TELEVISION
Chassis No.
Chassis GA8P
No. GA6
MODEL 21G-FX10L
In the interests of user safety (Required by safety regulations in some countries) the set should be restored to its original
condition and only parts indentical to those specified should be used.
CONTENTS Page
IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................................... 1-1
LOCATION OF USER’S CONTROL ...................................................................................................................... 2-1
INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................................. 3-1
SERVICE MODE ..................................................................................................................................................... 4-1
ADJUSTMENT METHOD ........................................................................................................................................ 5-1
WAVEFORMS ......................................................................................................................................................... 6-1
CHASSIS LAYOUT ................................................................................................................................................. 7-1
BLOCK DIAGRAM .................................................................................................................................................. 8-1
DESCRIPTION OF SCHEMATIC DIAGRAM .......................................................................................................... 9-1
SCHEMATIC DIAGRAMS ......................................................................................................................................10-1
PRINTED WIRING BOARD ASSEMBLIES ........................................................................................................... 11-1
Parts Guide
ELECTRICAL SPECIFICATIONS
POWER INPUT............................AC 110-220 V, 50/60 Hz SPEAKER
POWER RATING .....................................................89W SIZE ........................................................ 9 x 5cm, 2pcs
PICTURE SIZE .............................1,239 cm2 (192sq inch) VOICE COIL IMPEDANCE .................16 ohm at 400 Hz
CONVERGENCE ............................................. Magnetic ANTENNA INPUT IMPEDANCE
SWEEP DEFLECTION .................................. .. Magnetic VHF/UHF ........................................75 ohm Unbalanced
FOCUS ......................................................... Electrostatic TUNING RANGES
VHF-Channels ................................................. 2 thru 13
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ...................... 45.75 MHz UHF-Channels ................................................14 thru 69
CATV Channels ............................................. 1 thru 125
Sound IF Carrier Frequency ...................... 41.25 MHz
(EIA, Channel Plan U.S.A.)
Color Sub-Carrier Frequency ......................42.17 MHz
(Nominal) Specifications are subject to change without
AUDIO POWER
OUTPUT RATING... ...................... 3.0 W(RMS) x 2pcs prior notice.
This document has been published to be used for after

SHARP CORPORATION sales service only.
The contents are subject to change without notice.
21G-FX10L
CHAPTER 1. IMPORTANT SERVICE SAFETY PRECAUTION
Service Manual
TV
E
Market
21G-FX10L
IMPORTANT SERVICE SAFETY PRECAUTION

Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING X-RADIATION AND HIGH VOLTAGE LIMITS

1. For continued safety, no modification of any circuit 1. Be sure all service personnel are aware of the
should be attempted. procedures and instructions covering X-radiation.
2. Disconnect AC power before servicing. The only potential source of X-ray in current solid
3. Semiconductor heat sinks are potential shock state TV receivers is the picture tube. However, the
hazards when the chassis is operating. picture tube does not emit measurable X-Ray
4. The chassis in this receiver has two ground systems radiation, if the high voltage is as specified in the
which are separated by insulating material. The non- "High Voltage Check" instructions.
isolated (hot) ground system is for the B+ voltage It is only when high voltage is excessive that X-
regulator circuit and the horizontal output circuit. The radiation is capable of penetrating the shell of the
isolated ground system is for the low B+ DC voltages picture tube including the lead in the glass material.
and the secondary circuit of the high voltage The important precaution is to keep the high voltage
transformer. below the maximum level specified.
To prevent electrical shock use an isolation 2. It is essential that servicemen have available at all
transformer between the line cord and power times an accurate high voltage meter.
receptacle, when servicing this chassis. The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
SERVICING OF HIGH VOLTAGE SYSTEM there is no possibility of an X-radiation problem.
AND PICTURE TUBE Every time a color chassis is serviced, the brightness
should be tested while monitoring the high voltage
When servicing the high voltage system, with a meter to be certain that the high voltage does
remove the static charge by connecting a not exceed the specified value and that it is regulating
10k ohm resistor in series with an insulated correctly.
5. Do not use a picture tube other than that specified
wire (such as a test probe) between the pic- or make unrecommended circuit modifications to the
ture tube ground and the anode lead. (AC high voltage circuitry.
line cord should be disconnected from AC 6. W h e n t r o u b l e s h o o t i n g a n d t a k i n g t e s t
outlet.) measurements on a receiver with excessive high
voltage, avoid being unnecessarily close to the
1. Picture tube in this receiver employs integral receiver.
implosion protection. Do not operate the receiver longer than is necessary
2. Replace with tube of the same type number for to locate the cause of excessive voltage.
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
1–1
21G-FX10L
IMPORTANT SERVICE SAFETY PRECAUTION

(Continued)
BEFORE RETURNING THE RECEIVER • Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
(Fire & Shock Hazard) cabinet, screw heads, knobs and control shafts,
Before returning the receiver to the user, perform escutcheon, etc.) and measure the AC voltage drop
the following safety checks. across the resistor.
AII checks must be repeated with the AC line cord
1. Inspect all lead dress to make certain that leads are plug connection reversed. (If necessary, a non-
not pinched or that hardware is not lodged between polarized adapter plug must be used only for the
the chassis and other metal parts in the receiver. purpose of completing these check.)
2. Inspect all protective devices such as non-metallic Any current measured must not exceed 0.5 milliamp.
control knobs, insulating materials, cabinet backs, Any measurements not within the limits outlined
adjustment and compartment covers or shields, above indicate of a potential shock hazard and
isolation resistor-capacity networks, mechanical corrective action must be taken before returning the
insulators, etc. instrument to the customer.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 110~220 volt AC
outlet, (Do not use an isolation transformer for this
test). DVM
• Using two clip leads, connect a 1.5k ohm, 10 watt AC SCALE
resistor paralleled by a 0.15μF capacitor in series
with all exposed metal cabinet parts and a known 1.5k ohm
10W
earth ground, such as electrical conduit or electrical
ground connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
TO EXPOSED CONNECT TO
METAL PARTS KNOWN EARTH
GROUND
SAFETY NOTICE
Many electrical and mechanical parts in television For continued protection, replacement parts must be
receivers have special safety-related characteristics. identical to those used in the original circuit. The use of
These characteristics are often not evident from visual substitute replacement parts which do not have the same
inspection, nor can protection afforded by them be safety characteristics as the factory recommended
necessarily increased by using replacement components replacement parts shown in this service manual, may
rated for higher voltage, wattage, etc. create shock, fire, X-radiation or other hazards.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by " "
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
1–2
21G-FX10L
CHAPTER 2. LOCATION OF USER'S CONTROL
Service Manual
TV
E
Market
21G-FX10L
[1] LOCATION OF USER'S CONTROL
AVa AV a
AV
2–1
21G-FX10L
CHAPTER 3. INSTALLATION AND SERVICE INSTRUCTIONS
Service Manual
TV
E
Market
21G-FX10L
INSTALLATION AND SERVICE INSTRUCTIONS

Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION HIGH VOLTAGE CHECK

The receiver is protected by a 3.15A fuse (F701), High voltage is not adjustable but must be checked
mounted on PWB-A, wired into one side of the AC to verify that the receiver is operating within safe
line input. and efficient design limitations as specified checks
should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST
1. Connect an accurate high voltage meter between
After service has been performed on the horizontal ground and anode of picture tube.
deflection system, high voltage system, B+ system, 2. Operate receiver for at least 15 minutes at 110~220V
test the X-Radiation protection circuit to ascertain AC line voltage, with a strong air signal or a properly
proper operation as follows: tuned in test signal.
3. Enter the service mode and set Y-mute ON by using
1. Apply 110~220V AC using a variac transformer for Service R/C.
accurate input voltage. 4. The voltage should be approximately 26kV (at zero
2. Allow for warm up and adjust all customer controls beam).
for normal picture and sound. If a correct reading cannot be obtained, check circuitry
3. Receive a good local channel. for malfunctioning components. After the voltage test,
4. Connect a digital voltmeter to C602 +ve and make make Y-mute off to the normal mode.
sure that the voltmeter reads 20 ±1.1V.
5. Apply external 28.5V DC at C602 +ve by using an
external DC supply, TV must be shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between C602 -ve and C602 +ve.
Now make sure that normal picture appears on the
screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
3–1
21G-FX10L
CHAPTER 4. SERVICE MODE
Service Manual
TV
E
Market
21G-FX10L
SERVICE MODE
1. Service mode is switched by SERVICE key, CH UP + VOL DOWN when reset.

2. Service mode is cancelled by SERVICE key during Service mode.
3. Service mode can be switched to the following 5 modes via MENU key:
First mode of service when entering by

Adjustment mode SERVICE key.
Setting mode
First mode of service when entering by

Confirmation mode 2 local keys.
Option mode
NVM Edit mode
4䋮During Service mode, AFT operation is prohibited. The setting data for PLL is always set to fo data.
5䋮During Service mode, the following user data are set to default value and stored as last memory.
PICTURE䋯TINT䋯COLOR䋯BRIGHT䋯SHARP䋯COLOR TEMP.
BASS䋯TREBLE䋯BALANCE䋯MTS䋯FAO䋯SPEAKER䋯ENERGY SAVE
6䋮During Service mode, OSD display for ON/OFF is toggled via [CH CALL] key.
䊶At display OFF condition, if changing adjustment data, channel, input source, it remains display OFF.
䊶At display OFF condition, if changing adjustment item, it returns to display ON.
7䋮During Service mode, the following operation are prohibited.
CLOSED CAPTION䋯No signal BLUE SCREEN
8䋮During Service mode, sound is muted(only MTSIC) except when selecting the following items.
V24, M01
4–1
21G-FX10L
AUTO ADJUSTMENT
H-VCO
1. When there is H-VCO auto adjustment key input at item H-VCO, auto adjustment will be implemented.
2. H-FREE (1chip) is set to 1.
3. H-OUT (1chip) is set by intelligent monitor output.
4. IM input becomes TIM input.
5. H-VCO (1chip) data is changed so that the number is 126 inside 8ms interval.
6. When adjustment is completed, OSD display and H-VCO auto adjustment data of EERPOM are updated.
7. H-FREE (1chip), intelligent monitor output, IM input mode are recovered.
RF-AGC
1. If there is RF-AGC auto adjustment key input at item RF-AGC, auto adjustment will be implemented.
2. AGC-OUT (MONITOR(1chip)is set by intelligent monitor output.
3. IM input becomes AD input.
4. RF-AGC(1chip) is decreased from current RF-AGC value to 0, the maximum AFT input voltage is obtained.
5. RF-AGC(1chip) is increased until at the point of AFT input voltage is (max. 0.3V), adjustment is completed.
6. When adjustment is completed, OSD display and RFGC auto adjustment status in EEPROM are updated.
7. Intelligent monitor output, IM input mode are recovered.
PIF-VCO
1. If there is PIF-VCO auto adjustment key input at item PIF- VCO, auto adjustment will be implemented.
2. VIF-DEF (1chip) is set to 1.
3. AFT output (1chip) is set by intelligent monitor output.
5. VIF-VCO (1chip) is changed so the input voltage becomes 2.5V.
6. When adjustment is completed, OSD display and PIF-VCO auto adjustment status in EEPROM are updated.
7. VIF-DEF (1chip) intelligent monitor output, IM input mode are recovered.
S-TRAP
1. If there is S-TRAP auto adjustment key input at item S-TRAP, auto adjustment will be implemented.
2. S-TRAP OUTPUT is set by intelligent monitor output.
4. S-Trap (1chip) is set to the value of V45(S-TRAP ADJ Start).
5. S_Trap_Result is set to the value of V45(S-TRAP ADJ Start).
6. S-Trap (1chip) is increased until the minimum input voltage becomes minimum.
7. Wait 20ms before sampling the new_ AD_data.
8. When adjustment is completed, OSD display and S-TRAP auto adjustment status in EEPROM are updated.
9. S-TRAP (1chip) intelligent monitor output, IM input mode are recovered.
4–2
21G-FX10L
CHAPTER 5. ADJUSTMENT METHOD
Service Manual
TV
E
Market
21G-FX10L
Memory Map Data
Caution: To get into the service mode, one of the ways is press direct key for service items.
There is three stage of Service Mode data

First stage data from V01 ~ M01
to go into second stage of service mode data, press MENU key
Second stage data from F01 ~ F160

to go into third stage of service mode data, press MENU key
Third stage data from O01 ~ O31
Adjustmet Mode (First Stage)

DATA INITIAL
EEPROM ITEMS OSD SETTING DATA FIX/ADJ/AUTO REMARK
LENGTH DATA
SUB-CON V01 0~127 127 127 ADJ
SUB-TINT V02 0~127 64 64 ADJ
SUB-COL V03 0~127 64 64 ADJ
SUB-BRI V04 0~255 128 128 ADJ
SUB-SHP-PRE V05 0~63 41 40 *FIX
SUB-SHP-OVER V06 0~63 41 24 *FIX
V-SHIFT V07 0~7 4 4 ADJ
H-SHIFT V08 0~31 16 16 ADJ
RF-AGC V09 0~127 127 127 AUTO
V-SIZE V10 0~63 32 32 ADJ
V-SHIFT50 V11 -7~+7 0 0 FIX
H-SHIFT50 V12 -15~+15 0 0 FIX
V-SIZE50 V13 -31~+31 0 0 FIX
VIF-VCO V14 0~63 32 32 AUTO
R-CUT V15 0~255 127 127 ADJ
G-CUT V16 0~255 127 127 ADJ
B-CUT V17 0~255 127 127 ADJ
R-DRI V18 0~127 64 64 ADJ
B-DRI V19 0~127 64 64 ADJ
SUB-COLOR-YUV V20 0~127 64 64 FIX
SUB-TINT-YUV V21 0~127 64 64 FIX
CC-POS V22 0~255 32 32 ADJ
SCREEN CUT OFF V23 0~2 0 0 FIX
0~127 (O20=0) 127 115
SUB-VOL V24 *FIX
0~255 (O20=1) 255 -
H-VCO V25 0~7 4 4 AUTO
S-TRAP V26 0~127 64 64 AUTO
ADJUST IF NECESSARY TO
VS-CORRECT V27 0~63 36 26 *FIX IMPROVE
VS-CORRECT50 V28 -13~+13 0 0 FIX
ADJUST IF NECESSARY TO
V LINEARITY V29 0~63 35 37 *FIX IMPROVE
V LINEARITY50 V30 -13~+13 0 0 FIX
PARABOLA V31 0~63 32 32 ADJ
PARABOLA50 V32 -13~+13 0 0 FIX
TRAPEZIUM V33 0~63 32 32 ADJ
TRAPEZIUM50 V34 -13~+13 0 0 FIX
H-SIZE V35 0~63 32 32 ADJ
H-SIZE50 V36 -13~+13 0 0 FIX
UPPER CORNER V37 0~63 32 32 ADJ
UPPER CORNER50 V38 -13~+13 0 0 FIX
LOWER CORNER V39 0~63 32 32 ADJ
LOWER CORNER50 V40 -13~+13 0 0 FIX
ANGLE ADJ V41 0~63 31 31 ADJ
ANGLE ADJ50 V42 -13~+13 0 0 FIX
BOW ADJ V43 0~63 31 31 ADJ
BOW ADJ50 V44 -13~+13 0 0 FIX
S-TRAP ADJ START V45 0~127 25 25 FIX
S-TRAP STOP V46 0~127 95 95 FIX
MTS-ATT M01 0~15 10 10 FIX
Auto Adjustment Item

Ԙ H-VCO , ԙ RF-AGC, Ԛ VIF-VCO, ԛ S-TRAP
Remark: * Initial Data different with Setting Data
5–1
21G-FX10L
SETTING MODE (Second Stage)

DATA INITIAL
EEPROM ITEMS OSD SETTING DATA FIX/ADJ/AUTO
LENGTH DATA
ABCL-Gain F01 0/1 0 0 FIX
SHP-AV-PRE F02 -16~+16 0 -10 *FIX
SHP-YUV-PRE F03 -16~+16 0 0 FIX
SHP-P-PRE F04 -31~+31 0 0 FIX
SHP-N3-PRE F05 -31~+31 0 0 FIX
SHP-AV-OVER F06 -16~+16 0 -10 *FIX
SHP-YUV-OVER F07 -16~+16 0 0 FIX
SHP-P-OVER F08 -31~+31 0 0 FIX
SHP-N3-OVER F09 -31~+31 0 0 FIX
SHP ANT-ON II OFFSET F10 -15~0 -10 -10 FIX
RGB-CLIP F11 0/1 0 0 FIX
E-SAVE F12 0~63 30 30 FIX
0~127 (O20=0) 120 81
FAO-VOL F13 *FIX
0~255 (O20=1) 246 -
VIF-G F14 0~7 5 7 *FIX
YDL-TV F15 0~7 5 5 FIX
YDL-TV-P F16 0~7 5 5 FIX
YDL-TV-N3 F17 0~7 5 5 FIX
YDL-AV F18 0~7 5 5 FIX
YDL-AV-P F19 0~7 5 5 FIX
YDL-AV-N3 F20 0~7 5 4 *FIX
YDL-YUV F21 0~7 0 0 FIX
TINT-AV F22 -32~+32 +6 -16 *FIX
COL-AV F23 -32~+32 0 +10 *FIX
COL-P F24 -31~+31 +24 +24 FIX
COL-N3 F25 -31~+31 0 0 FIX
R-R F26 -32~+32 +3 +7 *FIX
R-B F27 -32~+32 -2 0 *FIX
B-R F28 -32~+32 -8 -20 *FIX
B-B F29 -32~+32 +6 +9 *FIX
GAMMA F30 0~3 1 3 *FIX
BS-D F31 0~3 0 0 FIX
BS-C F32 0~3 0 0 FIX
SL-TV F33 0~7 2 1 *FIX
SL-AV F34 0~7 2 2 FIX
SL-YUV F35 0~7 0 0 FIX
AFC2 F36 0~3 0 1 *FIX
VD-TV F37 0~7 5 1 *FIX
VD-AV F38 0~7 7 2 *FIX
VD-YUV F39 0~7 1 0 *FIX
AS-TV F40 0/1 1 1 FIX
AS-AV F41 0/1 1 1 FIX
AS-YUV F42 0/1 0 0 FIX
FBP-TV F43 0/1 0 0 FIX
FBP-AV F44 0/1 0 0 FIX
FBP-YUV F45 0/1 0 0 FIX
C.Clip Level F46 0/1 0 0 FIX
CP F47 0/1 1 1 FIX
CC LEVEL F48 0~31 0 0 FIX
OSD POS-H F49 0~31 0 14 *FIX
OSD POS-V50 F50 1~55 38 48 *FIX
OSD POS-V60 F51 1~50 23 32 *FIX
OFFSET-ADJ-COLOR F52 -32~+32 +10 +15 *FIX
OFFSET-ADJ-TINT F53 -32~+32 +2 +9 *FIX
WAIT˴MD˴TIMER F54 0/1 1 1 FIX
R-CUT-YUV F55 -63~+63 0 0 FIX
G-CUT-YUV F56 -63~+63 0 0 FIX
B-CUT-YUV F57 -63~+63 0 0 FIX
R-DRI-YUV F58 -63~+63 0 0 FIX
B-DRI-YUV F59 -63~+63 0 0 FIX
5–2
21G-FX10L

DATA INITIAL
LENGTH DATA
ABCL GOFFSET
CONTRAST i F60 -63~+63 0 0 FIX
CONTRAST YUV OFFSET F61 -63~+63 0 0 FIX
BRIGHT OFFSET F62 -63~+63 0 0 FIX
BRIGHT AV2 OFFSET F63 -15~+15 +1 +4 *FIX
BRIGHT YUV OFFSET F64 -63~+63 0 0 FIX
TRAP F65 0~3 2 0 *FIX
TRAP-P F66 0~3 2 2 FIX
TRAP-N3 F67 0~3 2 2 FIX
AFC1-Gain-TV F68 0~3 0 0 FIX
AFC1-Gain-AV F69 0~3 3 3 FIX
AFC1-Gain-YUV F70 0~3 3 3 FIX
OM-DET F71 0/1 0 0 FIX
㧮㧿㧙㧳㨍㨕㨚 F72 0~2 0 0 FIX
C-ANGLE F73 0/1 0 0 FIX
㨂㧙㧰㧸 F74 0~3 0 0 FIX
㨁㧙㧰㧸 F75 0~3 0 0 FIX
AS-SPEED-DN F76 0/1 0 0 FIX
AS-SPEED-UP F77 0/1 0 0 FIX
CR-PEDESTEL-ADJ F78 0~15 8 8 FIX
CB-PEDESTEL-ADJ F79 0~15 8 8 FIX
SIF-BPF-WIDE F80 0~7 3 1 *FIX
SIF-BPF-WIDE-LOW F81 0/1 0 0 FIX
SIF-BPF-WIDE-HIGH F82 0/1 0 0 FIX
0: 11XX (AUTO)
1: 0011 (PAL-M)
COL-SYSTEM F83 2: 0111 (PAL-N) 3 3 FIX
3: 0110 (N358)
4: 10XX (AUTO1)
Pow-Storage F84 0/1 1 1 FIX
SIF45 GAIN DOWN F85 0/1 0 0 FIX
S-TRAP OFF F86 0/1 1 0 *FIX
BASS OFFSET F87 -4~+4 0 0 FIX
MID1 OFFSET F88 -4~+4 0 0 FIX
TREBLE OFFSET F91 -4~+4 0 0 FIX
AVL LEVEL F92 0~3 0 1 *FIX
0: fix to 0
1: fix to 1
AVL OPTION F93 2 1 *FIX
2: AVL in
SOUND MENU
AU-ATT AMP F94 0 (0dB)/1(3dB) 0 1 *FIX
0: 10%
1: 30%
OSD LEVEL F95 2: 50% 3 3 FIX
3: 70%
4: 90%
R MTX UP F96 0/1 0 0 FIX
MATRIX ADJ F97 0~3 0 0 FIX
SAP LEVEL F98 0/1 0 0 FIX
STEREO SENS F99 0/1 0 0 FIX
SAP SENS F100 0/1 0 0 FIX
MER F101 0~255 70 70 FIX
MEL1 F102 0~255 150 150 FIX
MEL2 F103 0~255 156 156 FIX
MEL3 F104 0~255 163 163 FIX
MEL4 F105 0~255 165 165 FIX
MEL5 F106 0~255 170 170 FIX
MEL6 F107 0~255 180 180 FIX
S-St-Point F108 0~60 21 21 FIX
5–3
21G-FX10L

DATA INITIAL
LENGTH DATA
ABCL G i
S-Sp-Point F109 0~60 60 60 FIX
S-Step F110 0~60 7 7 FIX
CONT NEWS F111 0~60 40 40 FIX
CONT MUSIC F112 0~60 50 50 FIX
CONT MOVIE F113 0~60 60 60 FIX
BRIGHT NEWS F114 -30~+30 0 0 FIX
BRIGHT MUSIC F115 -30~+30 0 0 FIX
BRIGHT MOVIE F116 -30~+30 0 0 FIX
COL NEWS F117 -30~+30 0 0 FIX
COL MUSIC F118 -30~+30 0 0 FIX
COL MOVIE F119 -30~+30 +10 +10 FIX
SHARP NEWS F120 -30~+30 -10 -10 FIX
SHARP MUSIC F121 -30~+30 0 0 FIX
SHARP MOVIE F122 -30~+30 +5 +5 FIX
SURR NEWS F123 0(OFF)/1(ON) 0 0 FIX
SURR MUSIC F124 0(OFF)/1(ON) 0 0 FIX
SURR MOVIE F125 0(OFF)/1(ON) 0 0 FIX
TREBLE NEWS F126 -10~+10 -10 -10 FIX
TREBLE MUSIC F127 -10~+10 0 0 FIX
TREBLE MOVIE F128 -10~+10 +5 +5 FIX
BASS NEWS F129 -10~+10 -5 -5 FIX
BASS MUSIC F130 -10~+10 0 0 FIX
BASS MOVIE F131 -10~+10 +10 +10 FIX
EQ BASS NEWS F132 -10~+10 0 0 FIX
EQ BASS MUSIC F133 -10~+10 0 0 FIX
EQ BASS MOVIE F134 -10~+10 0 0 FIX
EQ MID1 NEWS F135 -10~+10 0 0 FIX
EQ MID1 MUSIC F136 -10~+10 0 0 FIX
EQ MID1 MOVIE F137 -10~+10 0 0 FIX
EQ MID2 NEWS F138 -10~+10 0 0 FIX
EQ MID3 NEWS F141 -10~+10 0 0 FIX
EQ TRE NEWS F144 -10~+10 0 0 FIX
EQ TRE MUSIC F145 -10~+10 0 0 FIX
EQ TRE MOVIE F146 -10~+10 0 0 FIX
S-BOOST NEWS F147 0(OFF)/1(ON) 0 0 FIX
S-BOOST MUSIC F148 0(OFF)/1(ON) 1 1 FIX
S-BOOST MOVIE F149 0(OFF)/1(ON) 1 1 FIX
CORNER UP-LOW EN F150 0/1 1 1 FIX
BOW/ANGLE-ON/OFF F151 0(OFF)/1(ON) 1 1 FIX
SHP-NR-OFFSET F152 -15~0 0 0 FIX
V-FREE60 F153 0/1 1 1 FIX
TAKEOFF TV F154 0/1 0 0 FIX
STRAP OFFSET F155 -16~+16 0 0 FIX
RGB MUTE TIME F156 0~8 0 1 *FIX
H-BLK LEFT F157 0~7 0 0 FIX
H-BLK RIGHT F158 0~7 0 3 *FIX
0: 5ms
1: 10ms
H-STOP DELAY F159 1 1 FIX
2: 15ms
3: 20ms
SYS MUTE F160 0/1 0 0 FIX
5–4
21G-FX10L
Setting Mode (Third stage)

INITIAL
Data OPTION FUNCTION Description Range Setting Data
DATA
0 : ALPS
O01 LNA TUNER 0/1 0 0
1 : MATSUSHITA
O02 FAO DIS/ENA 0/1 1 0
O03 * PON-CH DIS/ENA 0/1 0 1
O04 ANTENNA BOOSTER DIS/ENA 0/1 0 0
O05 AV DIS/ENA 0/1 1 1
0 : AV1
O06 AV2 0/1 1 1
1 : AV2
O07 MTS DIS/ENA 0/1 1 0
0 : without COMPONENT
O08 COMPONENT 1 : COMPONENT (share with AV1) 0…2 1 0
2 : COMPONENT (individual)
0 : Without Sound Menu
O09 TONE-CTRL 1 : TONE
0…3 1 3
2 : EQUALIZER
3 : Without Sound Menu (GA8P)
O10 AUTO-OFF DIS/ENA 0/1 1 1
0 : Standby Mode
O11 LAST POWER 0/1 0 0
1 : Last Memory
0 : No Set Up
O12 SETUP-FLAG 0/1 1 1
1 : AUTO Set Up
O13 AV MODE DIS/ENA 0/1 1 0
O14 MP-IN DIS/ENA 0/1 0 0
O15 S-BOOSTER DIS/ENA 0/1 0 0
O16 FORCE-COL DIS/ENA 0/1 0 0
0 : ENGLISH
O17 INIT-LANG 1 : SPANISH 0…2 0 1
2 : PORTUGUESE
O18 LANG-SEL Portuguese/French/Spanish 0…7 7 1
0 : CH ٌ/ٖ, VOL+/-
O19 ARROW-KEY 0/1 1 0
1: / , /
0 : 7-bit volume table
O20 VOL-TABLE 0/1 0 0
1 : 8-bit volume table
0 : EZ Setup Same as GA6 Brazil
O21 AUTO-JUDGEMENT 0/1 1 1
1: EZ Setup Same as GA6 LAG
O22 WHITE-OUT DIS/ENA 0/1 0 0
O23 H-SYNC JUDGE DIS/ENA 0/1 1 1
O24 CHSET COLOR DIS/ENA 0/1 0 0
O25 DEMO DIS/ENA 0/1 1 1
O26 FLAT DIS/ENA 0/1 1 1
0 : No AV
1 : Rear
O27 F/R-AV 0…3 3 3
2 : Front
3 : Rear & Front
O28 SPEAKER DIS/ENA 0/1 1 0
0 : Old Vol-Table
O29 VOL-CURVE 0/1 0 1
1 : New Vol-Table
0 : -105 ~ 0
O30 CONTRAST TABLE 1 : -60 ~ 0 0…2 0 0
2 : -30 ~ 0
0 : -60 ~ +60
O31 BRIGHTNESS TABLE 0/1 0 0
1 : -30 ~ +30
* POWER ON BY CH-UP / DOWN KEY.
5–5
21G-FX10L
ADJUSTMENT PRECAUTION : Make sure TV Set is in "NORMAL CONDITION" before switch to Service Mode for Adjustment.
PIF ADJUSTMENT CHECKING
NO ADJUSTMENT POINT ADJUSTMENT CONDITION/PROCEDURE WAVEFORM OR OTHERS

1 RF-AGC (1) Receive the "US 10 CH HALF Color Bar" signal. * for Auto ADJ
TAKE OVER POINT Signal Strength: 56 ± 1dBμV (75 ohm open) 1)Receive "NTSC COLOUR BAR" signal
ADJUSTMENT (2) Connect the oscilloscope to JA402 (Tuner's AGC Terminal) as shown in signal strength : 56 ± 1 dBμV (75 ohm open).
(I2C BUS CONTROL) figure 3-1. 1) Go to service mode.
+ OSCILLOSCOPE 2) Go to service data V09 , press R/C to operate
(AUTO & MANUAL ADJ) "Auto-AGC" key and confirm the OK display
JA402
0.1V on the screen
- 3) If appear red display with NG sign, increase data some
step and please repeat step 2.
+ BIAS BOX 4) Proceed step 4 & 5 in manual mode.
TV SET
-
Bias Box : about 4.5V
Fig. 3-1
(3) Call V09 in service mode. Adjust the V09 bus data to obtain the Tuner
output pin drop 0.1V below maximum voltage.
(4) Change the antenna input signal to 63 ~ 67dBμV, and make sure there
is no noise.
(5)Turn up the input signal to 90 ~ 95 dBμV to be sure that there is no cross
modulation beat.
FOCUS ADJUSTMENT
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR REMARKS

1 FOCUS (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).
(2) Press RESET to set Picture NORMAL condition.
(3) Adjust the focus control to get the best focusing.
Focusing Point (middle
of center and edge of
monoscope pattern)
H-VCO, VIF-VCO & S-TRAP fo ADJUSTMENT
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR OTHERS

1 H-VCO ADJ (Manual Adj)
(I2C BUS CONTROL) (1) In No signal (RASTER) condition.
(AUTO & MANUAL ADJ) (2) Go to service mode, choose service data V25.
(3) Connect oscilloscope to IC801 pin13 (H-OUT), adj V25 until freq
become 15.735 ± 0.2KHz.
(Auto Adj)
(1) In No signal (RASTER) condition.
(2) Go to service mode.
(3) Choose service data V25, by pressing R/C "AUTO H-VCO" key, OSD will appear "OK"
at screen.
(4) If appear "NG" pls repeat step 3.
2 VIF-VCO ADJ (Manual Adj) *NOTE:

(I2C BUS CONTROL) (1) In No signal (RASTER) condition. This adjustment must be done after aging
(AUTO & MANUAL ADJ) (2) Go to service mode, choose service data V14 at least 3 minutes.
(3) Connect oscilloscope to IC801 pin7 (AFT), adj V14 until voltage become
2.5 ± 0.5 V DC (Checking spec : 2.50 ± 1.5 V)
(Auto Adj)
(2) Go to service mode, choose service data V14.
(3) Press the R/C "AUTO PIF-VCO" key, OSD will appear "OK" at screen.
3 S-TRAP fo ADJ (Manual ADJ)

(I2C BUS CONTROL) (1) In No signal (RASTER) condition.
(AUTO & MANUAL ADJ) (2) Go to service mode, choose service data V26.
(3) Connect oscilloscope to TP 801 or IC801 pin 30, adj V26 until voltage become Min (below 5 V).
(Auto Adj)
(2) Go to service mode, choose service data V26.
(3) Press the R/C "AUTO S-TRAP" key, OSD will appear "OK" at screen.
5–6
21G-FX10L
HORIZONTAL ,VERTICAL,DEFLECTION LOOP ADJUSTMENT (1)

1 V-SHIFT (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz). Figure A B
(I2C BUS CONTROL) (2) Choose the service data V07.
(3) Adjust V07 to align the center of the screen to the geometric center of CRT.
Note: B line (Monoscope middle line) must same or nearest higher position
to the A mark (Tube middle mark),refer to the attach drawing.
OK OK NG
2 V-SIZE (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).
(to be done after V-shift adj) (3) Adjust V10 bus data until the overscan become 10 ± 2.5 %.
Caution 1: Pls aging TV more than 10 minutes before adjustment
3 V-LINEARITY (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).

(3 )Already preset. (Adjust this unless the linearity is achieved.)
4 VS CORRECTION (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).

(3 )Already preset. (Adjust this unless the linearity is achieved.)
5 H-SHIFT (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).

(3) Adjust the V08 bus data to have a balance position to spec of A=B (as attach drawing). A B
(4) If cannot make it to A=B, adjust from the best point so that A slightly smaller than B.
6 H-SIZE (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).

(I2C BUS CONTROL) (2) Choose the service data V35
(3) Adjust V35 bus data until the overscan becomes 10 ± 2.5 %.
7 PARABOLA (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).

Adjust the 2nd vertical line from the right end of the crosshatch pattern
so that the middle 4 blocks are straight.
(3) Make sure both left / right of 2nd vertical line at optimum point
5–7
21G-FX10L
HORIZONTAL ,VERTICAL,DEFLECTION LOOP ADJUSTMENT (2)

8 UPPER CORNER (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).
(3) Adjust the 2nd upper vertical line from the right end of the crosshatch pattern
so that the upper line are straight.
9 LOWER CORNER (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).

(3) Adjust the 2nd lower vertical line from the right end of the crosshatch pattern
so that the bottom line are straight.
10 BOW-ADJ (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).

(I2C BUS CONTROL) (2) Choose the service data V43 BOW ADJ
(3) Adjust the 2nd vertical line from the end of the crosshatch pattern until line is straight.
H-BOW
11 ANGLE ADJ (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).

(3) Adjust the 2nd vertical line from the end of the crosshatch pattern line is straight
12 TRAPEZIUM (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).

(I2C BUS CONTROL) (2) Choose the service data V33 D2 D2
(3) Adjust the 2nd vertical line from the right end of the crosshatch pattern
so that the D1 (center area of the second vertical line - edge of screen) D1 D1
and D2 (top area of the second vertical line - edge of screen) are same.
13 FINAL INSPECTION OF (1) Receive CrossHatch Pattern Signal (NTSC 60Hz).

A2
ADJUSTMENT (2) Please make sure picture distortion (overall picture quality) must be balance at optimum point A1
D1
TOP / BOTTOM at LEFT / RIGHT corner. ~
A1 ~ A2
(3) If NG, please RE-ADJUST follow step 7 to 13 or adjust at NG position to get best picture quality A1 ~
B1 ~ B2
~
C1 ~ C2
B1 B2
D2 D1 = D2
C1 C2
OVERALL PICTURE QUALITY MUST BE

BALANCE AT OPTIMUM POINT ( LEFT
& RIGHT )
5–8
21G-FX10L
CLOSED CAPTION ADJUSTMENT

1 CLOSED CAPTION (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz)
SET UP (2) Go to service mode, choose service data V22.
(3) Adjust the V22 bus data to have a balance position to spec of A=B
(4) After the left and right symmetrical then V22 data reduce 5 step
A B
SCREEN, WHITE BALANCE, SUB-BRIGHTNESS & SUB-CONTRAST ADJUSTMENT(1)

1 SCREEN (1) Set the service data before adjust CRT cutoff as follows: NOTE:
ADJUSTMENT a) V01 : 127 Service data R/C key (Hex)
(I2C BUS CONTROL) b) V04 : 127 R-cutoff up A9
c) V15 : 127 R-cutoff down 69
d) V16 : 127 G-cutoff up E9
e) V17 : 127 G-cutoff down 19
f) V18 : 64 B-cutoff up 99
g) V19 : 64 B-cutoff down 59
(2) Receive the window pattern or US4 CH LION HEAD Signal (NTSC 60 Hz)
(3) Go to service mode, get in Y-mute by R/C and set V23 to "1"
(4) Adjust the Screen so that cut-off line appear in low bright, then judge that whether
the cut-off data appear in Red or Green or Blue color, in this condition between V15 = R-CUTOFF,
V16=G-CUTOFF & V17= B-CUTOFF, fix the data of the color appear in cut-off line and adj the
other two cut-off line so that cut-off line color become white.
(5)Turn the screen VR of FBT so that cut-off line just disappear and use R/C to set V23 to "0".
Next disable the Y-Mute so that the picture appear in normal mode
2 WHITE BALANCE ADJ (1)WHITE (HIGH BEAM)

(to be done after screen First use Minolta Color Analyzer CA100, let the gun point at Dark White position
adj) (as drawing attach), Adj V04 until LUMINANCE Y become 5 cd/m2, then let the gun
(I2C BUS CONTROL) point at White position ( as drawing attach), Adj V01 until LUMINANCE Y
(CH 23 50IRE become: 150 cd/m2. White Dark
WINDOW PATTERN) Adj the V18(R DRIVE) , V19(B DRIVE) until the axis of color temperature become White
10700° X : 0.278 , Y : 0.280
(2) DARK WHITE (LOW BEAM)

Let the gun point at Dark White position, if the color temperature data shift away from
the data adjusted in Item 1 Screen adjustment, adjust V15,V16,V17. 50% WHITE
Please fix the first colour appears in Screen adj item step (4) is fixed,
adj the other two so that to obtain the similar axis as above *Note : Use RF CH23 50IRE window pattern
** Repeat step 1 & 2 to get a regulated position
5–9
21G-FX10L
SCREEN, WHITE BALANCE, SUB-BRIGHTNESS & SUB-CONTRAST ADJUSTMENT(2)

3 SUB-BRIGHTNESS (1) In CH 23 50IRE window pattern signal condition.
(to be done after screen, (2) Using Minolta Color Analyzer CA-100, let the gun point atDark White position US14
white balance adj) (as attach drawing), adjust V04 Bus data until BRIGHTNESS Y = 1.5cd/m2
(I2C BUS CONTROL)
Service Luminance Tolarance (cd/m2)
Mode (cd/m2) Upper Limit Lower Limit
Enable 1.5 +0.5 -0.5
Disable 1.5 +1.5 -0.5
Dark White
4 SUB-CONTRAST (1) In CH 23 50IRE window pattern signal condition.

(to be done after screen, (2) Using Minolta Color Analyzer CA-100, let the gun point atWhite position US14
white balance adj, (as attach drawing), adjust V01 Bus data until BRIGHTNESS Y = 150cd/m2
sub-brightness adj)
(I2C BUS CONTROL) ** NOTE: Allowable Data for V01 >=90, even Y can't match the spec
Service Luminance Tolarance (cd/m2)

Mode (cd/m2) Upper Limit Lower Limit
Enable 150.0 +10 -10
Disable 150.0 +10 -10 White
5 BEAM CURRENT CHECK (1) Receive US 4 CH LION HEAD Signal (NTSC 60 Hz).
(2) Press R/C to set Picture NORMAL condition.
(3) Connect the DC miliammeter between TP 603 ( + ) & TP 602 ( - )
(Full Scale: 3mA Range).
(4) Beam current must be within : 1000 ± 100μA
NTSC CHROMA ADJUSTMENT

1 SUB-TINT (1) Receive the "US 10 CH HALF Color Bar" signal.
(2) Connect the oscilloscope to JA410 or TP853 BLUE-OUT
(I2C BUS CONTROL)
Range : 500mV/Div (AC) (Use Probe 10:1)
Sweep time : 10 sec/Div
(3) Select the service data V02 . On Y-mute using the R/C.
(4) Adjust the V02 (Sub tint) data to obtain the waveform as shown in Figure 1.1
(B-Amp Base (TP853) must be in stepping level)
*REMARK : PLEASE MAKE SURE USE RF SIGNAL DURING SUB TINT ADJUSTMENT
Fig 1-1
2 SUB COLOR (1) Receive the "US 10 CH HALF Color Bar" signal.
(2) Make the image normal with the remote controller.
(I2C BUS CONTROL) (3) Connect the oscilloscope to JA401 (TP851) RED-OUT.
(to be done after
sub tint adj) Range : 500mV/Div (AC) ( Use Probe 10:1)
Sweep time : 10 sec/Div
(4) Select the service data V03. Adjust the V03 (Sub color) data to obtain the waveform
adjustment shown in Fig. 1-2.
(5) Fig 1.2 waveforms shows that the 75% white & red portions of color bar at the same level
Cy G
100% WHITE
*REMARK : PLEASE MAKE SURE USE RF SIGNAL DURING SUB COLOUR ADJUSTMENT
W Y Mg R B
Fig 1-2
5 – 10
21G-FX10L
PROTECTOR OPERATION CHECKING

1 H, V PROTECTOR (1) Receive US 4 CH LION HEAD Signal (NTSC 60 Hz).
(2) Connect output of Bias Box to D602 cathode (C602 positive).
(3) Set voltage of Bias Box to 18V and make sure the protector is not working.
(4) Set voltage of Bias Box to 28.5V. Make sure the protector is functioned, horizontal oscilation stop
and picture disappear.
(5) Pull out the AC cord at least 4 second before plugging in again (to make sure ohm -COM has
been reset) for the set to recover from protector mode
2 OTHER PROTECTOR (1) Once finish rectified Electrolytic Capacitor short testing in + B line,
check all possible damaged components on +B line.
(Use random selected set for inspection)
A/V INPUT & OUTPUT CHECKING

1 VIDEO AND AUDIO (1) Receive the "US 10 CH HALF Color Bar" signal.
OUTPUT CHECK (2) Terminate the Video output with a 75 ohm impedance.
( At signal is standard Color Bar Y/C=1/1, 87.5% Mod.)
Make sure the output is as specified (1.0 Vp-p ± 3 dB).
(3) Terminate the Audio output with a 47K ohm impedance.
( 400 Hz 100 % Mod. 47 k ohm, VOL Max. )
Set volume to max, make sure the O/P is as specified (2.5 Vp-p ± 0.5Vp-p)
.
2 VIDEO AND AUDIO (1) Using the INPUT key on the remote controller, make sure that the modes change in order of
INPUT CHECK TV, INPUT1,INPUT2 & TV again and the video & audio output are according
to the input terminal for each mode.
(2) Video cross-talk INPUT to TV checking :
a) When connect INPUT1 input, check TV also
b) When connect INPUT2 input, check TV also
3 HEADPHONE (1) Receive "US 4 CH LION HEAD Signal ( NTSC 60 Hz )" signal.
CHECK (2) Maximum volume , and check the headphone output with 400Hz sound and no sound
output from speaker.
5 – 11
21G-FX10L
FUNCTION OPERATION CHECKING (VIDEO & AUDIO) (1)
NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDUR E WAVEFORM OR REMARKS

1 PICTURE Key (1) Receive "US 4 CH LION HEAD Signal (NTSC 60 Hz)" signal.
(2) Press to Menu mode, then select Picture Mode and set to select CONTRAST.
(3) Press Volume Up/Down key to check whether the CONTRAST effect is OK or not.
2 COLOUR Key (1) Receive the "US 10 CH HALF Color Bar" signal
(2) Press to Menu mode, then select Picture Mode and set to select COLOUR.
(3) Press Volume Up/Down key to check whether the COLOUR effect is OK or not.
3 BRIGHTNESS Key (1) Receive "US 4 CH LION HEAD Signal (NTSC 60 Hz)" signal.
(2) Press to Menu mode, then select Picture Mode and set to select BRIGHTNESS.
(3) Press Volume Up/Down key to check whether the BRIGHTNESS effect is OK or not
4 TINT Key (1) Receive the "US 10 CH HALF Color Bar" signal
(2) Press to Menu mode, then select Picture Mode and select TINT.
(3) Press Volume Up/Down key to check TINT, UP for GREEN direction and
DOWN for RED direction whether is OK or not.
5 SHARPNESS Key (1) Receive "US 4 CH LION HEAD Signal (NTSC 60 Hz)" signal.
(2) Press to Menu mode, then select Picture Mode and set to select SHARPNESS.
(3) Press Volume Up/Down key to check whether the SHARPNESS effect is OK or NOT.
6 RESET KEY (1) Once in Picture Mode , and the RESET Key is pressed. *NOTE :
all the setting will be present to normal setting. In RESET Mode,when press RESET key,
will appear RESET OSD and all setting set to normal.
PICTURE 60
COLOUR 0
BRIGHTNESS 0
TINT 0
SHARP 0
PICTURE NR OFF
COLOR TEMP Mid
7 COLOR TEMP (1) Receive US 4 CH LION HEAD Signal ( NTSC 60 Hz ).

(2) Set FUNCTION to select WHITE TEMP.
(3) Press Volume Up/Down key to check WHITE TEMP Option, STANDARD.
NORMAL SETTING, WARM for more REDDISH direction changing, COOL for
more BLUISH direction changing.
5 – 12
21G-FX10L
CHECKING FUNCTION OPERATION (VIDEO & AUDIO) (3)

8 NOISE MUTE (1) Receive mono-tone signal.
CHECKING (2) Turn up the volume control to maximum, make sure the sound is
heard from the speakers. Then put the unit in no signal state.
(3) Check the sound mute is effective.
(4) Finally turn sound level of CTV to minimum.
9 OSD LANGUAGE (1) Check OSD LANGUAGE quantity and type for respective model.
QUANTITY CHECK
MODEL QUANTITY ENGLISH SPANISH
21G-FX10L 2 O O
10 CLOSED CAPTION (1) Receive closed caption channel.

CHECKING (2) Press R/C "CC" button, and the it will change from OFF to CC1 to CC2 to TEXT1 to TEXT2.
(3) Check the closed caption to make sure it is working accordingly.
SHOCK TEST CHECKING.

1 SHOCK TEST (1) Hit at the top of TV set for two time.
(2) Check TV set not damage and TV operation operate correctly.
ROM CORRECTION CHECKING

1 SOFTWARE VERSION (1) Go to SERVICE mode, press "MENU" key until the SERVICE mode display as in * OTHERS:
Figure 1 appeared.* INFO
(2) Check the SOFTWARE VERSION status by monitoring the screen, follow the model's setting.
Model Micon Version CHK1 CHK2

21G-FX10L RH-IXC843WJZZQ (Software Ver. 1.35) NO NO
MASK: N1
SOFT : 1.35
CHK1 :NO
CHK2 :NO
Figure 1
5 – 13
21G-FX10L
CHAPTER 6. WAVEFORMS
Service Manual
TV
E
Market
21G-FX10L
(1)1.94 Vp-p (2)4.60 Vp-p (3)3.79 Vp-p (4)4.20 Vp-p
Horiz. Rate Horiz. Rate Horiz. Rate Horiz. Rate
(5)3.30 Vp-p (6)4.88 Vp-p (7)6.12 Vp-p (8)1.45 Vp-p
Horiz. Rate Vert. Rate Horiz. Rate Vert. Rate
(9)2.79 Vp-p (10)22.65 Vp-p (11)1074 Vp-p (12)68.8 Vp-p
Horiz. Rate Horiz. Rate Horiz. Rate Vert. Rate
(13)6.48 Vp-p (14)153.00 Vp-p (15)517.00 Vp-p (16)115.20 Vp-p
Vert. Rate Horiz. Rate Horiz. Rate Horiz. Rate
(17)88.8 Vp-p (18) 104.80 Vp-p
Horiz. Rate Horiz. Rate
6–1
21G-FX10L
CHAPTER 7. CHASSIS LAYOUT
Service Manual
TV
E
Market
21G-FX10L
1 2 3 4 5 6 7 8 9 10
7–1
21G-FX10L
CHAPTER 8. BLOCK DIAGRAM
Service Manual
TV
E
Market
21G-FX10L
21G-FX10L
G
1 2 3 4 5 6 7 8 9 10
8–1
21G-FX10L
1 2 3 4 5 6 7 8 9 10
8–2
21G-FX10L
10 11 12 13 14 15 16 17 18 19
8–3
21G-FX10L
CHAPTER 9. DESCRIPTION OF SCHEMATIC DIAGRAM
Service Manual
TV
E
Market
21G-FX10L
DESCRIPTION OF SCHEMATIC DIAGRAM

NOTES: WAVEFORM MEASUREMENT CONDITIONS:
1. The unit of resistance "ohm" is omitted. 1. Photographs taken on a standard gated color bar
(K=kΩ=1000Ω, M=MΩ) signal, the tint setting adjusted for proper color. The
2. All resistors are 1/16 watt, unless otherwise noted. wave shapes at the red, green and blue cathodes of
3. All capacitors are μF, unless otherwise noted. the picture tube depend on the tint, color level and
(P=pF=μμF) picture control.
4. (G) indicates ±2% tolerance may be used. 2. indicates waveform check points (See chart,
5. indicates line isolated ground. waveforms are measured from point indicated to
chassis ground.)
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected AND SHADED ( ) COMPONENTS
between points indicated and chassis ground, line = SAFETY RELATED PARTS.
voltage set at 120V AC and all controls set for normal MARK= X-RAY RELATED PARTS.
picture unless otherwise indicated.
2. All voltages measured with 1000μ V B & W or Color DRGANNES MARQUES ET HACHRES ( ):
signal. PIECES RELATIVES A LA SECURITE.
MARQUE : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits

may be subject to change for product improvement
without prior notice.
9–1
21G-FX10L
CHAPTER 10. SCHEMATIC DIAGRAM
Service Manual
TV
E
Market
21G-FX10L
1 2 3 4 5 6 7 8 9 10
10 – 1
21G-FX10L
1 2 3 4 5 6 7 8 9 10
10 – 2
21G-FX10L
10 11 12 13 14 15 16 17 18 19
10 – 3
21G-FX10L
CHAPTER 11. PRINTED WIRING BOARD ASSEMBLIES
Service Manual
TV
E
Market
21G-FX10L
PWB-A : MAIN UNIT ( Wiring Side )

A
1 2 3 4 5 6 7 8 9 10
11 – 1
21G-FX10L
PWB-A : MAIN UNIT ( Chip Parts Side )

A
1 2 3 4 5 6 7 8 9 10
11 – 2
21G-FX10L
PWB-B : CRT UNIT ( Wiring Side )

A
1 2 3 4 5 6 7 8 9 10
11 – 3
21G-FX10L
PWB-B : CRT UNIT ( Chip Parts Side )

A
1 2 3 4 5 6 7 8 9 10
11 – 4
PartsGuide
21G-FX10L
PARTS GUIDE
No. XXXXXXXXXXXX
NO.S9914021GFX10L
XXXXXXXX
21G-FX10L
MODEL 21G-
CONTENTS
[1] PICTURE TUBE [5] MISCELLANEOUS PARTS
[2] PRINTED WIRING BOARD [6] SUPPLIED ACCESSORIES

ASSEMBLIES ( NOT REPLACE-
MENT ITEM ) [7] CABINET PARTS
[3] MAIN UNIT [8] PACKING PARTS ( NOT REPLACE-

MENT ITEM )
[4] CRT UNIT
INDEX
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used

for after sales service only.
The contents are subject to change without notice.
21G-FX10L
NO. PARTS CODE PRICE NEW PART DESCRIPTION
RANK MARK RANK
[1] PICTURE TUBE

! VB51QGT420X7E R SEMI-ITC Picture Tube
! RCILGA172WJZZ R Degaussing Coil
QEARCA052WJZZ AG R Ground-Part
[2] PRINTED WIRING BOARD ASSEMBLIES ( NOT REPLACEMENT ITEM )
DUNTKF187WEA6 - - MAIN Unit
DUNTKF188WEA6 - - CRT Unit
[3] MAIN UNIT
! TU201 RTUNQA037WJN1 R Tuner
IC301 VHILA42032E-1 R LA42032E-1
! IC501 VHILA78041+-1 AE R LA78041+-1
! IC701 VHISTRW5453-1 AM R I.C.
IC751 VHIPQ05RDA1-1 R I.C.
IC801 RH-IXC843WJZZQ R I.C.
IC1003 VHIM24C08W6-1Y AE R IM24C08W
IC3004 VSIMXC/C//-1Y R I.C.
Q201 VS2SC2735//1EY R 2SC2735//1E
Q601 VS2SC2235Y/1E+ AE R 2SC2235
Q602 VS2SC6090++1E AG R 2SC6090
Q603 VS2SC3198-G-1+ AA R 2SC3198
Q604 VS2SC3928AR-1Y AB R 2SC3928AR
Q605 VS2SD1913R/-1 R 2SD1913R/
Q671 VS2SA1266-G-1+ R 2SA1266-G
Q672 VS2SC3198-Y-1+ R 2SC3198-Y
Q752 VS2SD468-C/-1+ AD R 2SD468
Q753 VS2SD468-C/-1+ AD R 2SD468
Q754 VS2SD468-C/-1+ AD R 2SD468
Q802 VS2SA1530AR-1Y AB R 2SA1530AR
D201 VHEZJ33C+++1EY AA R Zener Diode , 33V
D203 VHDHSS4148+-1Y AA R Diode
D392 RH-DX0445CEZZ AE R Diode , DX0445CE
D393 RH-DX0247CEZZ R Diode , DX0247CE
D503 VHEZJ5R1B++1EY AB R Zener Diode , 5.1V
D505 RH-DXA094WJZZY AC R Diode , DXA094WJ
D510 RH-DX0302CEZZY AE R Diode , DX0302CE
D602 VHD1SS244//-1Y AB R Diode , 1SS244
D603 RH-EXA572WJZZY AA R Zener Diode , 27V
D606 RH-DXA049WJZZY AC R Diode , DXA049WJ
D608 VHEZJ6R2A++1EY R Zener Diode
D609 RH-DX0321CEZZY AE R Diode , DX0321CE
D611 RH-DXA006WJZZ AE R Diode , DXA006WJ
D670 RH-DXA049WJZZY AE R Diode , DXA049WJ
! D701 RH-DX0476CEZZ AG R Diode , DX0476CE
D706 RH-DX0066GEZZY AC R Diode , DX0066GE
D715 VHEZJ5R6B++1EY R Zener Diode
D722 VHEZJ27D+++1EY R Zener Diode
D723 VHEZJ12B+++1EY R Zener Diode
D736 VHEZJ36C+++1EY R Zener Diode
D750 VHEZJ5R1A++1EY AB R Zener Diode , 5.1V
D751 RH-DXA044WJZZ R Diode , DXA044WJ
D806 RH-EXA520WJZZY AB R Zener Diode
D807 RH-EXA535WJZZY AC R Zener Diode
D1001 RH-PX0013PEZZ AC R Photodiode
D1002 VHEZJ11A+++1EY AA R Zener Diode , 10.71V
VA701 RH-VXA182WJZZ R Varistor
X801 RCRSAA075WJZZ AF R Crystal
NR701 RH-HXA013WJZZ R
2
21G-FX10L
RANK MARK RANK
[3] MAIN UNIT

L203 QJUM-0001AJFWY R Jumper wire
L204 VP-XF1R2K0000Y AB R Peaking 1.2mH
L603 RCILZ1005CEZZ AD R Coil
L605 RCILZA115WJZZ R Coil
L701 RCILFA187WJZZ AD R Coil
L751 RCILP0179CEZZ+ R Coil
L802 VP-CF100K0000Y AB R Peaking 10mH
SF201 RFILCA055WJQZS R Coil
T602 RTRNFA143WJZZ R H-Volt Transformer
T603 RTRNZA058WJZZ AD R Transformer
T702 RTRNWA193WJZZ R Transformer
C202 VCEA0A1AW108M+ AC R 1000 10V Electrolytic
C203 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C204 VCEA0A1HW105M+ AB R 1 50V Electrolytic
C211 VCCCCY1HH390JY AA R 39p 50V Ceramic
C301 VCEA0A1EW476M+ AB R 47 25V Electrolytic
C302 VCEA0A1HW224M+ AB R 0.22 50V Electrolytic
C303 VCKYCY1HB332KY AA R 3.3 50V Ceramic
C306 VCEA0A1CW336M+ AC R 33 16V Electrolytic
C308 VCEA0A1EW477M+ AD R 470 25V Electrolytic
C309 VCFYFA1HA474J+ AE R 0.47 50V Mylar
C391 VCKYPA2HB102K+ AA R 1000p 500V Ceramic
C508 VCFYAA2AA224J+ AD R 0.22 100V Mylar
C509 VCKYPA1HB103K+ AB R 10p 50V Ceramic
C513 RC-EZA332WJZZ+ AD R Capacitor
C515 VCEACA1HC335J+ AC R 3.3 50V Electrolytic
C601 VCQYTA1HM563J+ AB R 0.56 50V Mylar
C608 VCQYTA1HM273J+ AA R 0.27 50V Mylar
C610 VCEA0A1EW226M+ AB R 22 25V Electrolytic
C613 RC-FZA178WJZZ R
C615 RC-FZ0357CEN1 R
C617 VCFPVC3ZA163H AD R 16 1.8KV Metalized Polypro Film
C618 VCQPPC2JB473J R
C619 RC-KZ0033CEZZ+ AC R 0.01 250V Ceramic
C635 VCFPKH2ED364J R
C671 VCKYPA1HB102K+ AA R 1 50V Ceramic
C672 VCKYCY1HB103KY AB R 10p 50V Ceramic
C701 RC-FZA018WJZZ AD R 220 275V Metalized Plastic Film
C705 RC-EZA229WJZZ AM R 220 400V Electrolytic
C706 VCFYSA1HB105J+ R Capacitor
C709 VCQYTA1HM103J+ AB R 50V Mylar
C710 VCQYTA1HM103J+ AB R 50V Mylar
C713 RC-KZ0102GEZZ AC R 2kV Ceramic
C743 VCKYPH3DB561K AC R 560p 2KV Ceramic
C752 VCKYPH3DB561K AC R 560p 2KV Ceramic
C753 RC-EZA235WJZZ AD R 160V Electrolytic
3
21G-FX10L
RANK MARK RANK
[3] MAIN UNIT

C755 VCEA0A1CW226M+ AB R 22 16V Electrolytic
C756 VCEA0A1EW228M+ AE R 2200 25V Electrolytic
C767 RC-EZB478WJZZ+ R
C784 RC-KZ1018CEZZ AC R 2KV Ceramic
C811 VCFYFA1HA224J+ AA R 0.22 50V Mylar
C831 VCEA0A1AW477M+ AB R 470 10V Electrolytic
C840 VCKYCY1CF105ZY AB R 1 16V Ceramic
C841 VCKYCY1CB393KY AB R 3.9 16V Ceramic
C842 VCKYCY1CF105ZY AB R 1 16V Ceramic
C1001 VCEA0A1AW107M+ AB R 100 10V Electrolytic
C1004 VCKYCY1CF474ZY AB R 0.47 16V Ceramic
C1016 VCKYCY1EF104ZY AA R 0.1 25V Ceramic
C1017 VCKYCY1HB221KY AA R 220 50V Ceramic
C1021 VCKYCY1EF104ZY AA R 0.1 25V Ceramic
C1081 VCQYTA1HM104J+ AA R 0.1 50V Mylar
RJ14 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
R201 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R205 VRD-RA2BE680JY AA R 68 1/8W Carbon
R206 VRS-CY1JF122JY AA R 1.2K 1/16W Metal Oxide
R216 VRS-RG3LB393J+ AC R 39K 3W Metal Oxide
R301 VRD-RA2BE272JY AA R 2.7K 1/8W Carbon
R302 VRN-RL3DBR68J+ AB R 68 2W Metal Film
R303 VRS-CY1JF473JY AA R 47K 1/16W Metal Oxide
4
21G-FX10L
RANK MARK RANK
[3] MAIN UNIT

R304 VRD-RA2BE223JY AA R 22K 1/8W Carbon
R325 VRD-RM2HD1R0JY AA R 1 1/2W Carbon
R391 VRN-RL3ABR10J+ AB R 10 1W Metal Oxide
R459 VRD-RA2EE750JY AA R 75 1/8W Carbon
R502 VRS-VV3AB561J AB R 560 1W Metal Oxide
R503 VRN-RL3DBR56J+ AB R 56 2W Metal Film
R513 VRD-RM2HD333JY AA R 33K 1/2W Carbon
R514 VRD-RM2HD682JY AA R 6.8K 1/2W Carbon
R609 VRD-RM2HD330JY AA R 33 1/2W Carbon
R611 VRN-RL3AB1R5J+ AB R 1.5 1W Metal Film
R621 VRN-RL2HC4R7J+ AB R 4.7 1/2W Metal Oxide
R622 VRS-RG3DB682J+ AB R 6.8 2W Metal Film
R642 VRS-VV3LB180J R
R643 VRS-KT3LB103J R
R644 VRS-KA3HG681J R
R702 VRS-VV3DB124J AB R 120K 1W Metal Film
R705 VRN-RL3DB1R0J+ AB R 1 2W Metal Film
R706 VRN-RL3DBR18J+ AB R 0.18 2W Metal Film
R711 VRD-RA2EE472JY AA R 4.7K 1/4W Carbon
R726 VRN-SV2HCR22J AB R 0.22 1/2W Metal Oxide
R750 VRS-RG3AB180J+ AB R 18 1W Metal Oxide
R751 RR-DZ0049CEZZY R 39M 1/2W Carbon Film
R752 RR-DZ0049CEZZY R 39M 1/2W Carbon Film
5
21G-FX10L
RANK MARK RANK
[3] MAIN UNIT

R754 VRS-RG3LB680J+ AC R 68 3W Metal Oxide
R757 VRN-VV3AB150J AB R 15 1W Metal Oxide
R758 VRN-VV3AB180J AB R 18 1W Metal Oxide
R820 QJUM-0001AJFWY R Jumper wire
R1049 VRS-CY1JF105JY AA R 1M 1/16W Metal Oxide
R1800 VRD-RA2EE474JY AA R 470K 1/4W Carbon
S701 QSW-PA006WJZZ AG R Switch , POWER
S1001 QSW-KA019WJZZ+ AC R Switch , CH UP
S1002 QSW-KA019WJZZ+ AC R Switch , CH DOWN
S1003 QSW-KA019WJZZ+ AC R Switch , VOL UP
S1004 QSW-KA019WJZZ+ AC R Switch , VOL DOWN
S1005 QSW-KA019WJZZ+ AC R Switch , MENU
! F701 QFS-C3225CEZZ AC R Fuse , 3.15A 250V
FH701 QFSHDA008WJZZ+ AC R Fuse Holder
FH702 QFSHDA008WJZZ+ AC R Fuse Holder
6
21G-FX10L
RANK MARK RANK
[3] MAIN UNIT

J351 QJAKJA020WJZZ R Jack
J402 QJAKEA056WJ04 R Jack
J405 QTANJA136WJZZ R Jack
P302 QPLGNA109WJZZ AB R Plug ,4Pin(S)
P601 QPLGNA796WJZZ AC R Plug ,6Pin(F)
P602 LHLDW1104PEZZ AB R Plug
P701 QPLGNA792WJZZ AC R Plug ,2Pin(M)
P702 QPLGN0269GEZZ AB R Plug ,2Pin
P1001 LHLDW1105PEZZ AB R Plug
P1002 QPLGNA110WJZZ AB R Plug ,5Pin(BC)
RMC1001 RRMCUA052WJZZ AG R Remote Receiver
RDA301 PRDARA420WJFW R Heat Sink for IC301
RDA501 PRDARA759WJFW AD R Heat Sink for IC501
RDA602 PRDARA361WJFW R Heat Sink for Q602
RDA605 PRDARA361WJFW R Heat Sink for Q605
RDA701 PRDARA119WJFW AF R Heat Sink for IC701
RDA751 PRDARA167WJFW R Heat Sink for IC751
TP801 QPLUGP0111GEFW R Plug
[4] CRT UNIT

Q853 VSBF422++++2+ AC R BF422+
Q854 VSBF422++++2+ AC R BF422+
Q855 VSBF422++++2+ AC R BF422+
Q894 VS2SA1530AR-1Y AB R 2SA1530AR
D896 VHEZJ5R6C++1EY AA R Zener Diode , 5.6V
D898 VHD1N4148//-1Y R Zener Diode
L851 VP-MK820K0000+ AB R Peaking 82mH
C880 RC-KZ018JCEZZ AC R 10000p 1.5KV Ceramic
R859 VRS-RG3DB183J+ AB R 18K 2W Metal Film
R861 VRS-RG3DB183J+ AB R 18K 2W Metal Film
! R863 VRS-RG3DB183J+ AB R 18K 2W Metal Film
! R864 VRD-RA2BE100JY AA R 10 1/8W Carbon
! R876 VRS-CY1JF121JY AA R 120 1/16W Metal Oxide
P860 LHLDW1104PEZZ AB R Plug 4Pin (H)
P880 LHLDW1105PEZZ AB R Plug 5Pin (K)
SC851 QSOCVA023WJZZ AE R Socket , 12Pin
[5] MISCELLANEOUS PARTS
! ACC701 QACCZA091WJPZ R AC Cord
VSP9050PA02WA AH R SPEAKER
QCNW-F201WJPZ R SP WIRE (+--+)
QCNW-A230WJN1 AD R H-WIRE
QCNW-A788WJN1 AD R K-WIRE
[6] SUPPLIED ACCESSORIES
RRMCGA799WJSA R Infrared Remote Control Unit
TINS-E297WJZZ R Operation Manual
UBATUA024WJZZ R Battery
7
21G-FX10L
[7] CABINET PARTS
21G-FX10L
1-1 1
1-6
1-7
1-2 1-3 1-4 1-5 2 2-1
2-2
8
21G-FX10L

RANK MARK RANK
[7] CABINET PARTS

1 CCABAC304WEV4 - R Front Cabinet Ass'y
1-1 Not Available - - Front Cabinet
1-2 JBTN-A846WJKA - R Power Button
1-3 MSPRC0005PEFW - R Power Button Spring
1-4 GCOVAD398WJSA - R R/C & LED Cover
1-5 JBTN-A831WJKA - R Control Button
1-6 HBDGBA085WJKA - R Sharp Badge
1-7 HDECAA030WJSA - R Aluminium Decoration
2 CCABBB546WEV0 - R Rear Cabinet Ass'y
2-1 Not Available - - Rear Cabinet
2-2 LHLDWA101WJKZ - R AC Cord Hook
9
21G-FX10L
[8] PACKING PARTS ( NOT REPLACEMENT ITEM )
PACKING OF THE SHEET
6 SSAKA0001PEZZ
*Polyethylene Bag
Operation Manual
Batteries
4 Infra Red R/C Unit
SPAKP0099PEZZ
* Wrapping Sack
5 SPAKXC550WJZZ
*Buffer Material
3 SPAKCF102WJZZ
* Packing Case
USE 2 PACKING TAPES

FIX THE PACKING CASE
MARK *: Not replacement items
10
21G-FX10L

RANK MARK RANK
[8] PACKING PARTS ( NOT REPLACEMENT ITEM )

3 SPAKCF102WJZZ - - Packing Case
4 SPAKP0099PEZZ - - Wrapping Sack
5 SPAKXC550WJZZ - - Buffer Material
6 SSAKA0001PEZZ - - Polyethylene Bag
11
21G-FX10L
INDEX
PRICE NEW PART PRICE NEW PART
PARTS CODE No. PARTS CODE No.
RANK MARK RANK RANK MARK RANK
[ C ] RC-KZ0029CEZZ+ 3-C702 AC R
CCABAC304WEV4 7-1 - R " 3-C703 AC R
CCABBB546WEV0 7-2 - R " 3-C704 AC R
[ D ] RC-KZ0033CEZZ+ 3-C619 AC R
DUNTKF187WEA6 2- - - RC-KZ0102GEZZ 3-C713 AC R
DUNTKF188WEA6 2- - - RC-KZ018JCEZZ 4-C880 AC R
[ G ] RC-KZ1018CEZZ 3-C784 AC R
GCOVAD398WJSA 7-1-4 - R RCRSAA075WJZZ 3-X801 AF R
[ H ] RFILCA055WJQZS 3-SF201 R
HBDGBA085WJKA 7-1-6 - R RH-DX0066GEZZY 3-D706 AC R
HDECAA030WJSA 7-1-7 - R " 3-D707 AC R
[ J ] " 3-D709 AC R
JBTN-A831WJKA 7-1-5 - R " 3-D721 AC R
JBTN-A846WJKA 7-1-2 - R " 3-D1081 AC R
RH-DX0247CEZZ 3-D393 R
[ L ]
" 3-D752 AE R
LHLDW1104PEZZ 3-P602 AB R
RH-DX0255CEZZ 3-D610 AE R
" 4-P860 AB R
RH-DX0302CEZZY 3-D510 AE R
LHLDW1105PEZZ 3-P1001 AB R
RH-DX0321CEZZY 3-D609 AE R
" 4-P880 AB R
RH-DX0445CEZZ 3-D392 AE R
LHLDWA101WJKZ 7-2-2 - R
RH-DX0476CEZZ 3-D701 AG R
[ M ]
RH-DXA006WJZZ 3-D611 AE R
MSPRC0005PEFW 7-1-3 - R
RH-DXA044WJZZ 3-D751 R
[ N ]
RH-DXA049WJZZY 3-D606 AC R
Not Available 7-1-1 - -
" 3-D670 AE R
" 7-2-1 - -
RH-DXA094WJZZY 3-D505 AC R
[ P ]
RH-EXA520WJZZY 3-D806 AB R
PRDARA119WJFW 3-RDA701 AF R
" 3-D1006 AB R
PRDARA167WJFW 3-RDA751 R
" 3-D1009 AB R
RH-EXA535WJZZY 3-D807 AC R
" 3-RDA605 R
" 3-D808 AC R
" 3-D809 AC R
PRDARA759WJFW 3-RDA501 AD R
RH-EXA572WJZZY 3-D603 AA R
[ Q ]
RH-HXA013WJZZ 3-NR701 R
QACCZA091WJPZ 5-ACC701 R
RH-IXC843WJZZQ 3-IC801 R
QCNW-A230WJN1 5- AD R
RH-PX0013PEZZ 3-D1001 AC R
QCNW-A788WJN1 5- AD R
RH-VXA182WJZZ 3-VA701 R
QCNW-F201WJPZ 5- R
RR-DZ0049CEZZY 3-R751 R
QEARCA052WJZZ 1- AG R
" 3-R752 R
QFS-C3225CEZZ 3-F701 AC R
RRMCGA799WJSA 6- R
QFSHDA008WJZZ+ 3-FH701 AC R
RRMCUA052WJZZ 3-RMC1001 AG R
" 3-FH702 AC R
RTRNFA143WJZZ 3-T602 R
QJAKEA056WJ04 3-J402 R
RTRNWA193WJZZ 3-T702 R
RTRNZA058WJZZ 3-T603 AD R
RTUNQA037WJN1 3-TU201 R
QJAKJA020WJZZ 3-J351 R
[ S ]
QJUM-0001AJFWY 3-L203 R
SPAKCF102WJZZ 8-3 - -
" 3-L804 R
SPAKP0099PEZZ 8-4 - -
" 3-L805 R
SPAKXC550WJZZ 8-5 - -
" 3-L807 R
SSAKA0001PEZZ 8-6 - -
" 3-R820 R
[ T ]
" 3-R1013 R
TINS-E297WJZZ 6- R
" 3-R1014 R
[ U ]
QPLGN0269GEZZ 3-P702 AB R
UBATUA024WJZZ 6- R
QPLGNA109WJZZ 3-P302 AB R
[ V ]
QPLGNA110WJZZ 3-P1002 AB R
VB51QGT420X7E 1- R
QPLGNA792WJZZ 3-P701 AC R
VCCCCY1HH101JY 3-C1002 AA R
QPLGNA796WJZZ 3-P601 AC R
QPLUGP0111GEFW 3-TP801 R
QSOCVA023WJZZ 4-SC851 AE R
" 3-C212 AA R
QSW-KA019WJZZ+ 3-S1001 AC R
" 3-S1002 AC R
VCEA0A1AW107M+ 3-C1001 AB R
" 3-S1003 AC R
VCEA0A1AW108M+ 3-C202 AC R
" 3-S1004 AC R
VCEA0A1AW477M+ 3-C831 AB R
" 3-S1005 AC R
VCEA0A1CW106M+ 3-C311 AC R
QSW-PA006WJZZ 3-S701 AG R
" 3-C312 AC R
QTANJA136WJZZ 3-J405 R
" 3-C370 AC R
[ R ]
" 3-C390 AC R
RC-EZA229WJZZ 3-C705 AM R
VCEA0A1CW107M+ 3-C1003 AB R
RC-EZA235WJZZ 3-C753 AD R
RC-EZA332WJZZ+ 3-C513 AD R
" 3-C757 AB R
RC-EZB478WJZZ+ 3-C767 R
" 3-C761 AB R
RC-FZ0357CEN1 3-C615 R
RC-FZA018WJZZ 3-C701 AD R
VCEA0A1CW336M+ 3-C306 AC R
RC-FZA178WJZZ 3-C613 R
" 4-C893 AB R
RCILFA187WJZZ 3-L701 AD R
RCILGA172WJZZ 1- R
" 3-C760 AB R
RCILP0179CEZZ+ 3-L751 R
" 3-C806 AB R
RCILZ1005CEZZ 3-L603 AD R
" 3-C1007 AC R
RCILZA115WJZZ 3-L605 R
12
21G-FX10L
VCEA0A1CW477M+ 3-C451 AC R VCKYPA2HB102K+ 3-C391 AA R
" 3-C838 AC R " 3-C750 AA R
VCEA0A1EW108M+ 3-C393 AD R VCKYPH3DB561K 3-C743 AC R
VCEA0A1EW226M+ 3-C610 AB R " 3-C752 AC R
VCEA0A1EW228M+ 3-C756 AE R VCQPPC2JB473J 3-C618 R
VCEA0A1EW476M+ 3-C301 AB R VCQYTA1HM103J+ 3-C709 AB R
VCEA0A1EW477M+ 3-C308 AD R " 3-C710 AB R
VCEA0A1HW105M+ 3-C204 AB R VCQYTA1HM104J+ 3-C1081 AA R
" 3-C833 AB R VCQYTA1HM273J+ 3-C608 AA R
" 3-C844 AB R VCQYTA1HM563J+ 3-C601 AB R
" 3-C845 AB R VHD1N4148//-1Y 4-D898 R
" 3-C1018 AB R VHD1SS244//-1Y 3-D602 AB R
VCEA0A1HW106M+ 3-C206 AB R VHDHSS4148+-1Y 3-D203 AA R
" 3-C1850 AB R " 3-D605 AA R
VCEA0A1HW107M+ 3-C505 AB R " 3-D607 AA R
" 3-C304 AB R " 3-D763 AA R
" 3-C372 AB R " 3-D801 AA R
" 3-C394 AB R " 3-D1005 AA R
" 3-C395 AB R " 3-D1008 AA R
VCEA0A1HW335M+ 3-C826 AB R VHEZJ11A+++1EY 3-D1002 AA R
VCEA0A1HW474M+ 3-C804 AB R VHEZJ12B+++1EY 3-D723 R
" 3-C816 AB R VHEZJ27D+++1EY 3-D722 R
" 3-C825 AB R VHEZJ33C+++1EY 3-D201 AA R
" 3-C828 AB R VHEZJ36C+++1EY 3-D736 R
VCEA0A1HW475M+ 3-C314 AB R VHEZJ5R1A++1EY 3-D750 AB R
" 3-C602 AB R VHEZJ5R1B++1EY 3-D503 AB R
" 3-C843 AB R " 3-D754 AB R
VCEA0A1HW476M+ 3-C670 AB R VHEZJ5R6B++1EY 3-D715 R
" 3-C719 AB R VHEZJ5R6C++1EY 4-D896 AA R
VCEA0A1HW477M+ 3-C511 AB R VHEZJ6R2A++1EY 3-D608 R
VCEA0A2EW336M+ 3-C604 AD R VHEZJ8R2B++1EY 3-D732 AB R
VCEACA1HC335J+ 3-C515 AC R " 3-D757 AB R
VCFPKH2ED364J 3-C635 R VHILA42032E-1 3-IC301 R
VCFPVC3ZA163H 3-C617 AD R VHILA78041+-1 3-IC501 AE R
VCFYAA2AA224J+ 3-C508 AD R VHIM24C08W6-1Y 3-IC1003 AE R
VCFYFA1HA154J+ 3-C501 AE R VHIPQ05RDA1-1 3-IC751 R
VCFYFA1HA224J+ 3-C811 AA R VHISTRW5453-1 3-IC701 AM R
VCFYFA1HA474J+ 3-C309 AE R VP-CF100K0000Y 3-L802 AB R
" 3-C310 AE R " 3-L808 AB R
VCFYSA1HB105J+ 3-C706 R VP-CF220K0000Y 3-L803 AB R
VCKYCY1CB393KY 3-C841 AB R VP-MK820K0000+ 4-L851 AB R
VCKYCY1CF105ZY 3-C840 AB R VP-XF1R2K0000Y 3-L204 AB R
" 3-C842 AB R VRD-RA2BE100JY 4-R864 AA R
VCKYCY1CF474ZY 3-C1004 AB R VRD-RA2BE101JY 3-R1004 AA R
VCKYCY1EF104ZY 3-C1016 AA R " 3-R1008 AA R
" 3-C1021 AA R " 3-R1017 AA R
VCKYCY1HB102KY 3-C1019 AA R " 3-R1019 AA R
VCKYCY1HB103KY 3-C672 AB R " 3-R3003 AA R
" 3-C807 AA R " 3-R3006 AA R
" 3-C819 AA R VRD-RA2BE102JY 3-R1046 AA R
" 3-C830 AA R " 3-R1030 AA R
VCKYCY1HB104KY 3-C803 AA R VRD-RA2BE151JY 3-R679 AA R
" 3-C305 AA R " 3-R733 AA R
VCKYCY1HF103ZY 3-C203 AA R VRD-RA2BE332JY 3-R1016 AA R
" 3-C1013 AA R " 3-R318 AA R
VCKYPA1HB102K+ 3-C671 AA R " 3-R319 AA R
VCKYPA1HB103K+ 3-C509 AB R VRD-RA2EE472JY 3-R711 AA R
VCKYPA1HB561K+ 4-C852 AB R VRD-RM2HD101JY 3-R639 AA R
" 4-C853 AB R VRD-RM2HD102JY 3-R608 AA R
VCKYPA1HB821K+ 4-C851 AA R VRD-RM2HD104JY 3-R605 AA R
VCKYPA2HB101K+ 3-C650 AB R VRD-RM2HD124JY 3-R753 AA R
13
21G-FX10L
VRD-RM2HD151JY 3-R827 AA R " 3-R1032 AA R
VRD-RM2HD1R0JY 3-R325 AA R VRS-CY1JF104JY 3-R1010 AA R
" 3-R326 AA R " 3-R1027 AA R
" 3-R507 AA R " 3-R1044 AA R
" 3-R710 AA R VRS-CY1JF105JY 3-R1049 AA R
VRD-RM2HD270JY 3-R612 AA R VRS-CY1JF121JY 4-R876 AA R
VRN-RL2HC4R7J+ 3-R621 AB R VRS-CY1JF183JY 3-R1011 AA R
VRN-RL3AB1R5J+ 3-R611 AB R " 3-R1012 AA R
VRN-RL3ABR10J+ 3-R391 AB R " 3-R1020 AA R
VRN-RL3DB1R0J+ 3-R705 AB R " 3-R1022 AA R
VRN-RL3DBR18J+ 3-R706 AB R " 3-R1026 AA R
VRN-RL3DBR56J+ 3-R503 AB R VRS-CY1JF221JY 3-R207 AA R
VRN-RL3DBR68J+ 3-R302 AB R " 3-R208 AA R
VRN-SV2HCR22J 3-R726 AB R " 3-R220 AA R
VRN-VV3AB150J 3-R757 AB R " 3-R672 AA R
VRN-VV3AB180J 3-R758 AB R VRS-CY1JF222JY 3-R504 AA R
VRS-CY1JF000JY 3-R526 AA R " 3-R832 AA R
" 3-R676 AA R " 3-R833 AA R
" 3-RJ14 AA R " 3-R834 AA R
" 3-RJ17 AA R VRS-CY1JF223JY 3-R819 AA R
" 3-RJ32 AA R " 3-R828 AA R
" 3-RJ44 AA R " 3-R1040 AA R
" 3-RJ45 AA R " 3-R1041 AA R
" 3-RJ46 AA R " 3-R1056 AA R
" 3-RJ78 AA R " 4-R854 AA R
" 3-R1015 AA R " 4-R855 AA R
" 3-R1042 AA R " 4-R892 AA R
" 3-R1092 AA R " 4-R891 AA R
" 3-RJ310 AA R " 4-R851 AA R
" 3-RJ311 AA R " 4-R852 AA R
" 3-RJ313 AA R " 3-R371 AA R
" 3-RJ314 AA R " 3-R1048 AA R
VRS-CY1JF101JY 3-R201 AA R " 3-R374 AA R
" 3-R202 AA R " 3-R626 AA R
" 3-R462 AA R " 3-R838 AA R
" 3-R808 AA R " 3-R515 AA R
" 3-R818 AA R " 3-R802 AA R
" 3-R823 AA R " 3-R825 AA R
" 3-R1031 AA R " 3-R310 AA R
" 3-R1047 AA R " 3-R675 AA R
VRS-CY1JF102JY 3-R362 AA R VRS-CY1JF681JY 3-R678 AA R
" 3-R382 AA R " 3-R315 AA R
" 3-R384 AA R " 3-R520 AA R
" 3-R772 AA R " 3-R812 AA R
" 3-R774 AA R " 3-R1021 AA R
" 3-R1003 AA R VRS-KA3HG681J 3-R644 R
" 3-R3002 AA R VRS-KT3LB103J 3-R643 R
" 3-R3005 AA R VRS-RG3AB180J+ 3-R750 AB R
VRS-CY1JF103JY 3-R458 AA R VRS-RG3DB183J+ 4-R859 AB R
" 3-R523 AA R " 4-R861 AB R
" 3-R524 AA R " 4-R863 AB R
" 3-R618 AA R VRS-RG3DB682J+ 3-R622 AB R
" 3-R662 AA R VRS-RG3LB393J+ 3-R216 AC R
" 3-R810 AA R VRS-RG3LB680J+ 3-R754 AC R
" 3-R811 AA R VRS-VV3AB181J 3-R601 AB R
" 3-R1025 AA R " 3-R607 AB R
14
21G-FX10L
PRICE NEW PART
PARTS CODE No. RANK MARK RANK
VRS-VV3AB331J 3-R506 AB R
VRS-VV3AB561J 3-R502 AB R
VRS-VV3DB124J 3-R702 AB R
VRS-VV3LB180J 3-R642 R
VS2SA1266-G-1+ 3-Q671 R
VS2SA1530AR-1Y 3-Q802 AB R
" 4-Q894 AB R
VS2SC2235Y/1E+ 3-Q601 AE R
VS2SC2735//1EY 3-Q201 R
VS2SC3198-G-1+ 3-Q603 AA R
VS2SC3198-Y-1+ 3-Q672 R
VS2SC3928AR-1Y 3-Q604 AB R
" 3-Q762 AB R
" 3-Q764 AB R
" 3-Q801 AB R
" 3-Q1002 AB R
" 3-Q1003 AB R
VS2SC6090++1E 3-Q602 AG R
VS2SD1913R/-1 3-Q605 R
VS2SD468-C/-1+ 3-Q752 AD R
" 3-Q753 AD R
" 3-Q754 AD R
VSBF422++++2+ 4-Q853 AC R
" 4-Q854 AC R
" 4-Q855 AC R
VSIMXC/C//-1Y 3-IC3004 R
VSP9050PA02WA 5- AH R
15
EndPage
COPYRIGHT
COPYRIGHT © 2009
XXXXBY SHARP CORPORATION
BYSHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,

stored in a retrieval system, or transmitted in
COPYRIGHT © XXXX
any form or by any means, electronic,
BYSHARP mechanical,
CORPORATION
photocopying, recording, or otherwise, without
priorALL
written permission
RIGHTS of the publisher.
RESERVED.
No part of this publication may be reproduced,

stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
RQ0138-S
Sep 2009 Printed in Malaysia SHARP MANUFACTURING
Design and Production Information CORPORATION (M) SDN. BHD
Design :SEM PQA DEPARTMENT
Production :SMM Batu Pahat, Johor,
CHS.SMM Malaysia.
–1

Sharp 21GFx10L

Uploaded by

Copyright:

Available Formats

Sharp 21GFx10L

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sharp 21GFx10L

Uploaded by

Copyright:

Available Formats

21G-FX10L

This document has been published to be used for after

IMPORTANT SERVICE SAFETY PRECAUTION

WARNING X-RADIATION AND HIGH VOLTAGE LIMITS

IMPORTANT SERVICE SAFETY PRECAUTION

[1] LOCATION OF USER'S CONTROL

INSTALLATION AND SERVICE INSTRUCTIONS

CIRCUIT PROTECTION HIGH VOLTAGE CHECK

1. Service mode is switched by SERVICE key, CH UP + VOL DOWN when reset.

First mode of service when entering by

First mode of service when entering by

NVM Edit mode

Memory Map Data

There is three stage of Service Mode data

Second stage data from F01 ~ F160

Third stage data from O01 ~ O31

Adjustmet Mode (First Stage)

Auto Adjustment Item

Remark: * Initial Data different with Setting Data

SETTING MODE (Second Stage)

Remark: * Initial Data different with Setting Data

SETTING MODE (Second Stage)

Remark: * Initial Data different with Setting Data

SETTING MODE (Second Stage)

Remark: * Initial Data different with Setting Data

Setting Mode (Third stage)

O18 LANG-SEL Portuguese/French/Spanish 0…7 7 1

* POWER ON BY CH-UP / DOWN KEY.

PIF ADJUSTMENT CHECKING

NO ADJUSTMENT POINT ADJUSTMENT CONDITION/PROCEDURE WAVEFORM OR OTHERS

NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR REMARKS

H-VCO, VIF-VCO & S-TRAP fo ADJUSTMENT

NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR OTHERS

2 VIF-VCO ADJ (Manual Adj) *NOTE:

3 S-TRAP fo ADJ (Manual ADJ)

HORIZONTAL ,VERTICAL,DEFLECTION LOOP ADJUSTMENT (1)

NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR OTHERS

3 V-LINEARITY (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).

4 VS CORRECTION (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).

5 H-SHIFT (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).

6 H-SIZE (1) Receive US4 CH LION HEAD Signal (NTSC 60 Hz).

7 PARABOLA (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).

NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR OTHERS

9 LOWER CORNER (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).

10 BOW-ADJ (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).

11 ANGLE ADJ (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).

12 TRAPEZIUM (1) Receive CrossHatch Pattern Signal (NTSC 60 Hz).

13 FINAL INSPECTION OF (1) Receive CrossHatch Pattern Signal (NTSC 60Hz).

OVERALL PICTURE QUALITY MUST BE

CLOSED CAPTION ADJUSTMENT

NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR OTHERS

SCREEN, WHITE BALANCE, SUB-BRIGHTNESS & SUB-CONTRAST ADJUSTMENT(1)

NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR OTHERS

2 WHITE BALANCE ADJ (1)WHITE (HIGH BEAM)

10700° X : 0.278 , Y : 0.280

(2) DARK WHITE (LOW BEAM)

** Repeat step 1 & 2 to get a regulated position

SCREEN, WHITE BALANCE, SUB-BRIGHTNESS & SUB-CONTRAST ADJUSTMENT(2)

NO ADJUSTMENT POINT ADJUSTMENT CONDITION / PROCEDURE WAVEFORM OR OTHERS

4 SUB-CONTRAST (1) In CH 23 50IRE window pattern signal condition.