REVOLUTION™

PET PRO
QUICK START/USER GUIDE
1964, 1986, 2007 Series

More of a video
person? Look for this
icon and go online
for an instructional
how-to video at
www.BISSELL.com
5 www.BISSELL.com
Built for Pet Owners

CleanShot®
Use the on-board
pretreat CleanShot® at
any time while deep
cleaning your carpet to
target and remove tough
stains and odors.

EZ Clean Brush Roll Cover

BISSELL’s first deep cleaner with a nozzle and brush roll
cover that’s simple to remove and clean after use.
by Pet Owners
Remove Pet Hair,
Stains and Odors
with a single tool.
New!
Specialized
Pet Tools
Easily vacuum and
deep clean your
upholstery with
the new 2-in-1 Pet
Upholstery Tool.

Dry Mode:
Use the green switch
to change cleaning
modes. Begin with
Dry Mode to vacuum
and remove hair and
debris. Use a raking
motion to engage the
rubber & attract hair
to the suction channel.

Wet Mode:
Switch to Wet Mode
to deep clean. Keep
the tool in contact
with the surface and
press the trigger to
release spray while
pulling the tool
toward you.
Quick Start Guide

Assembly
WARNING
Do not plug in your deep cleaner until you are familiar with all instructions
and operating procedures.

Your deep cleaner • Base A Phillips screwdriver is

comes in four • Upper Handle required for Assembly in
easy-to-assemble • Clean Water Tank Step 3.
components and
an accessory bag. • Carry Handle

1 2

First, insert the

(aluminum)
Upper Handle
at the top of the
base until you
hear a “click”.
click
Do NOT put
the clean tank
on the machine
until Step 5.
Next, align the carry handle with the slots
on either side of the base (behind the
power switch and cleaning mode switch).
The carry handle will “click” into place.

3 4 5

Side
View

At the bottom of the

Use a Philips screwdriver upper handle, align the
to secure the screw (found Wrap the cord around clean water tank with
taped to upper handle) the carry handle and Quick the grooves and slide
into the carry handle. Release™ Cord Wrap hook. the tank into place.

www.BISSELL.com
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.
When using an electrical appliance, basic precautions should be observed, including the following:

WARNING
» Do not pull or carry by cord, » Do not use appliance in an
use cord as a handle, close enclosed space filled with
TO REDUCE THE RISK OF FIRE, a door on cord, or pull cord vapors given off by oil base
around sharp edges or corners. paint, paint thinner, some
ELECTRIC SHOCK, OR INJURY:
» Do not run appliance over moth proofing substances,
» Connect to a properly cord. Keep cord away from flammable dust, or other
grounded outlet only. See heated surfaces. explosive or toxic vapors.
grounding instructions. Do not » Do not unplug by pulling on » Do not use to pick up toxic
modify the 3-prong grounded cord. To unplug, grasp the material (chlorine bleach,
plug. plug, not the cord. ammonia, drain cleaner, etc.).
» Do not leave appliance when » Do not handle plug or » Do not pick up anything that
it is plugged in. Unplug from appliance with wet hands. is burning or smoking, such
outlet when not in use and » Do not put any object into as cigarettes, matches, or hot
before servicing. openings. Do not use with ashes.
» Do not expose to rain. Store any opening blocked; keep » Use only BISSELL cleaning
indoors. openings free of dust, lint, hair, products intended for use
» Do not allow to be used and anything that may reduce with this appliance to prevent
as a toy. Close attention is air flow. internal component damage.
necessary when used by or » Keep hair, loose clothing, See the Cleaning Formula
near children. fingers, and all parts of body section of this guide.
» Do not use for any purpose away from openings and » Do not immerse. Use only on
other than described in moving parts. surfaces moistened by the
this User’s Guide. Use only » Turn off all controls before cleaning process.
manufacturer’s recommended plugging or unplugging » Keep appliance on a level
attachments. appliance. surface.
» Do not use with damaged » Use extra care when cleaning » Do not carry the appliance
cord or plug. If appliance is on stairs. while in use.
not working as it should, or » Do not use to pick up » Always install float before any
has been dropped, damaged, flammable or combustible wet pick-up operation.
left outdoors, or dropped into materials (lighter fluid, gasoline, » Unplug before connecting
water, have it repaired at an kerosene, etc.) or use in areas TurboBrush® Tool.
authorized service center. where they may be present.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE
This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.

WARNING GROUNDING INSTRUCTIONS

Improper connection of the equipment-grounding
This appliance must be connected to a grounded
conductor can result in a risk of electrical shock. Check
wiring system. If it should malfunction or break down,
with a qualified electrician or service person if you
grounding provides a safe path of least resistance for
aren’t sure if the outlet is properly grounded. DO NOT
electrical current, reducing the risk of electrical shock.
MODIFY THE PLUG. If it will not fit the outlet, have a
The cord for this appliance has an
proper outlet installed by a qualified electrician. This
appliance is designed for use on a nominal 120-volt equipment-grounding conductor Grounded
and a grounding plug. It must Outlet
circuit, and has a grounding attachment plug that
only be plugged into an outlet
looks like the plug in the illustration. Make certain
that is properly installed and
that the appliance is connected to an outlet having
the same configuration as the plug. No plug adapter grounded in accordance with
should be used with this appliance. all local codes and ordinances.
Grounding Pin

www.BISSELL.com 5
 Thanks for buying a BISSELL carpet cleaner!
We love to clean and we’re excited to share one of our innovative products
with you. We want to make sure your carpet cleaner works as well as it
does today for years to come, so this guide has tips on using (pages 10-13),
maintaining (pages 16-19), and if there’s a problem, troubleshooting (page 20).

In just a few simple assembly steps, you’ll be ready to deep clean. Flip to the
front and let’s get started!

Package Contents
1. Upper Handle
2. 1 Screw attached to
Upper Handle
1. 2. 3. 4. 3. Base with Dirty Water Tank
4. Clean Water Tank
5. Carry Handle
6. BISSELL Professional Pet
Urine Eliminator + Oxy
7. BISSELL Pet Stain & Odor +
Antibacterial Formula
8. Accessory bag & hose
5. 6. 7. 9. Tough Stain Tool
10. 2-in-1 Pet Upholstery Tool
11. Nozzle Clean Out Tool

NOTE: Standard accessories

may vary by model. To identify
8. 9. 10. 11. what should be included with
your purchase, please refer
to the “Carton Contents” list
located on the carton top flap.

Assembly: Cover/Quick Start Guide Maintenance & Care . . . . . . . . . 16-19

Safety Instructions . . . . . . . . . . . . . . 5 Troubleshooting . . . . . . . . . . . . . . 20

Product View . . . . . . . . . . . . . . . . . . . 7 Warranty . . . . . . . . . . . . . . . . . . . . . . 21

Cleaning Formulas . . . . . . . . . . . . 8-9 Service . . . . . . . . . . . . . . . . . . . . . . . . 21

Operations . . . . . . . . . . . . . . . . . . 10-13 Product Registration . . . . . . . . . . . 22

Hose, Tools & CleanShot® . . . . 14-15 Parts & Supplies . . . . . . . . . . . . . . . . 22

6 www.BISSELL.com
 Getting to Know Your Deep Cleaner

In-Use
Cord Clip

Upper
Handle

Carry
Cleaning Mode
Handle
Switch
Spray Trigger

Rubber
Tab
Easy Fill/
Quick CleanShot® Formula Cap
Release™ Button
Cord Wrap

Clean Water Tank

(1 Gallon Capacity)

Recline
Pedal
EdgeSweep® Power
Brushes Button

Float Dirty Water Tank

Stack

Foot

Belt Access
Door

Belt/Brush
Access Plate
Nozzle

www.BISSELL.com 7
 Cleaning Formulas
WARNING
To reduce the risk of fire and electric shock due to internal component damage, use only
BISSELL cleaning fluids intended for use with the deep cleaner.

Keep plenty of genuine BISSELL formula Always use genuine BISSELL deep
on hand so you can clean and protect cleaning formulas. Non-BISSELL cleaning
whenever it fits your schedule. solutions may harm the machine and may
void the warranty.

BOOST PRETREAT
PRE TREAT SPOTS AND STAINS TO IMPROVE
CARPET CLEANING FORMULA ENHANCER CARPET CLEANING PERFORMANCE

Pet Oxy Pet PreTreat +

Oxy Boost Renew Boost Prevent Boost Oxy Stain Destroyer Pet Stain PreTreat
Boost Sanitize

Revives Repels stains Removes Pretreat to help

Removes old, Permanent Stain Penetrates to
carpets from soaking pet stains remove tough
set-in stains Removal in sanitize and loosen
to look into carpet and odors pet stains
permanently 30 seconds tough stains
their best fibers permanently and odors

PROFESSIONAL BARE FLOOR

FORMULAS 2X* CLEANING FORMULA FORMULAS

Pet Stain Professional Professional Pet Stain & DeepClean DeepClean Deep Clean Hard Floor
& Odor + Deep Pet Urine Odor & Protect + Refresh + Oxy Solutions
Antibacterial Cleaning Eliminator+Oxy

Our best Deep cleans Safe use for

Out cleans Removes
formula for carpets Powerful Removes linoleum,
Cleans and all other tough pet
pet urine and protects cleaning deep down vinyl, and
Controls formulas stains
stains & odors from future with a dirt, pet ceramic
odor causing Includes Includes
Includes stains with refreshing stains, & tile; removes
bacteria. Scotchgard™ Scotchgard™
Scotchgard™ Scotchgard™ scent pet odor tough
Protector Protector
Protector Protector dirt and grime

ONLY BISSELL Protects from future stains with Scotchgard™ Protector.

Scotchgard™ is a trademark of 3M®.
*2.5 fl. oz. of 2X concentrated formula is equivalent to 5.0 fl. oz. of non-concentrated formula.

Tips Before Carpet Cleaning

• If cleaning an entire room, consider moving your furniture to another area.
• Use a dry vacuum cleaner over area before using your deep cleaner.
• Pre-treat stains with BISSELL PreTreat to improve performance on coffee
stains and ground-in dirt.

8 www.BISSELL.com
Customize Your Clean & Maximize Your Results

ELIMINATE PET URINE, For Pet Stains & Odors:

STAINS & ODORS Erase pesky stains
& remove odors!
Pretreat pesky
pet stains with
BISSELL Pretreat
Our best formula for spray before
pet urine, stains, and using your deep
odors. Permanently cleaner. Choose
remove all three from a BISSELL pet
your carpet! formula for your
deep cleaner and
clean as directed.

To Clean Dark Stains: To Remove Ground-In Dirt:

Remove stains permanently! Renew your carpet!

Pretreat ground-in
dirt with a BISSELL
Use BISSELL Deep Pretreat Spray.
Clean + Oxy formula Choose BISSELL
or add BOOST OXY Professional Deep
to any of your favorite Cleaning formula
BISSELL formulas to and pair with a
maximize the stain BISSELL Boost
removal power. to enhance your
cleaning.

To Refresh Your Home: For Antibacterial Clean:

Choose your favorite scent! Use BISSELL Pet Stain & Odor +
Antibacterial formula
Pair your carpet
cleaner with
BISSELL
Febreze™ Use BISSELL Pet Stain
formulas to & Odor + Antibacterial
give your home with the Deep
a clean and Clean Mode of your
refreshing scent. machine to achieve
antibacterial results.

Always use genuine BISSELL deep cleaning formulas. Non-BISSELL

cleaning solutions may harm the machine and may void the warranty.

www.BISSELL.com 9
 Filling Your Clean Water Tank:
Antibacterial Formula

1 2 3
The clean water
tank is at the top
of the machine.

Clean Water Tank

(1 Gallon)

Dirty Water Tank

Lift the clean water tank Unscrew the cap from the
straight up to remove clean water tank. Add hot tap
from the machine. water to the water fill line.

4 5 For Future Use with Full Size

Antibacterial Formula:

After filling the

clean water tank
with hot tap
water, twist the
With Trial Size At the bottom of yellow cap back
Antibacterial Formula: the upper handle, onto the tank.
Pour into the clean align the clean
water tank with the Firmly insert the full size formula
tank up to the EasyFill bottle into the cap on the clean
line. Twist cap back grooves and slide
the tank into place. water tank and squeeze until
on to tank. formula reaches the EasyFill line.

A few notes about filling the clean water tank:

• Fill with hot (140°F/60°C MAX) tap water and add the appropriate
BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER
OR TANK IN MICROWAVE.
• When using BISSELL Antibacterial formula: Only fill your clean water
tank with the recommended amount of water and formula to achieve
antibacterial benefits.

NOTICE: Do not over wet carpet. Be careful not to run over loose objects or edges
of area rugs. Stalling the brush may result in premature belt failure.

NOTICE: BISSELL Antibacterial formula is only for BISSELL machines with EasyFill
System™.

10 www.BISSELL.com
 Filling Your Clean Water Tank:
2X Concentrated Formula

1 The clean water tank is at 2

the top of the machine.

Clean Water Tank

(1 Gallon)

Dirty Water Tank

Lift the clean water tank straight up to
remove from the machine.

3 4

With 2X Formula:
Unscrew the cap from
the clean water tank.
Add hot tap water to
the water fill line. Next,
reference the chart
below for formula
amounts to add to the
tank. Twist cap back
into place. At the bottom of the upper handle, align
the clean water tank with the grooves and
slide the tank into place.

FORMULA FILLING DEEP CLEAN MODE EXPRESS CLEAN MODE

INSTRUCTIONS
Fill water to the Water Fill Fill water to the Water Fill
BISSELL 2X Line that is next to DEEP Line that is next to EXPRESS
Concentrated Formulas CLEAN MODE on the Clean CLEAN MODE on the Clean
Tank. Add 2.5 oz of formula. Tank. Add 1.25 oz of formula.

NOTE: Fill with hot (140°F/60°C MAX) tap water and add the appropriate
BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR
TANK IN MICROWAVE. Do not substitute BISSELL 2X Formula cleaning solution
with other household cleaning products.

Pour in more power with BISSELL Boosts

• Fill tank with water and 2X formula (Step 3 above).
• Add 2 ounces of any BISSELL Boost per 1 gallon of water.
• The ProHeat 2X Revolution has a 1 gallon clean water tank.

www.BISSELL.com 11
 Cleaning Your Carpet
1 2
Select cleaning mode:
Deep Clean - Delivers a deep
Plug into clean to your carpet.
a properly
grounded Express Clean - Provides a
outlet. lighter clean with about 1 hour
of dry time.

3 4
To recline your
machine for use,
press the recline
pedal with your foot.

Press the power button

to turn the machine on.

NOTICE: To prevent
damage to Berber carpets,
avoid repeated strokes in
the same area.

Deep Clean Mode: Deep Clean Mode: Express Clean Mode:

1. Press the spray trigger When using BISSELL 1. Press the spray trigger to
to apply solution while Deep Clean + apply solution while making
making 2 slow wet passes - Antibacterial Formula 2 wet passes - 1 forward
1 forward and 1 back. and 1 back.
1. Press the spray trigger
2. Release the trigger. to apply solution while 2. Release the trigger.
3. Make 2 slow dry passes - making 3 slow wet passes 3. Make 2 dry passes -
1 forward and 1 back, to - 1 forward, 1 back, and 1 1 forward, 1 back to suck
suck up the dirty solution. forward again. up the dirty solution.
(Do not hold down the 2. Release the trigger. (Do not hold down the
trigger for this step.) trigger for this step.)
3. Make 1 slow dry pass
back, to suck up the dirty NOTE: In Express Clean
NOTE: For best cleaning Mode, the dirty tank
performance, clean with solution. (Do not hold down
the trigger for this step.) will not get as full as
your machine in Deep when cleaning with Deep
Clean Mode. Clean Mode.

12 www.BISSELL.com
Bare Floor Cleaning*
*Bare Floor Tool not included with machine.

WARNING
WARNING: To reduce the risk of fire and electric shock when cleaning a hard floor, the
BISSELL bare floor tool must be used and is only to be used with BISSELL Hard Floor
Solutions formula intended for use with this appliance.

NOTE: The bare floor tool that is compatible with the ProHeat 2X Revolution
is not included. It is available for purchase by contacting our team by phone or
visting us online at BISSELL.com.

1 2 3

When finished, unplug the

machine and remove the
With the machine unplugged,
Plug into a properly bare floor tool by rotating
attach the bare floor tool to
grounded outlet and press the tool up to unhook
the bottom of the machine
the power button. from the nozzle.
by lining the tool to the edge
of the nozzle. Rotate down Clean by pressing the Rinse and let dry before
until it clicks into place. trigger for 1 wet pass storing. Refer to page 16
forward, 1 wet pass back, for emptying the dirty
Follow filling instructions
and then release the water tank. Refer to
on page 10 or 11 and switch
trigger and make 1 dry pass page 17 for cleaning your
cleaning mode to Express
forward, 1 dry pass back. machine before storing.
Clean.

Area Rug Cleaning

Important! Please check manufacturer’s tag before cleaning area rugs for
any specialized cleaning instructions. We do not recommend deep cleaning
delicate, silk, wool, antique or area rugs without a manufacturer’s tag.

Regularly clean your high-traffic area rugs in Express Clean Mode:

• Check the manufacturer’s tag.
• Select Express Clean Mode.
• When cleaning area rugs, place the rug on a sealed surface to test for colorfastness
in an inconspicuous area. Your cleaner should not be used on unsealed surfaces.
• Important: Keep the foot of the deep cleaner perpendicular to the rug’s edge with
each cleaning pass to prevent damage.

www.BISSELL.com 13
 Cleaning with Hose & Tool
1 — Keep hair, loose clothing, fingers, and all parts
of body away from openings and moving parts.
Brushroll continues to rotate when in the upright
position.
— Brushroll continues to turn while product is
turned on and handle is in upright position. To avoid
damage to carpet, rugs, furniture and flooring, avoid
Lift the accessory tipping cleaner or setting it on furniture, fringed
hose door on top area rugs, or carpeted stairs during tool use.
of foot on the front — The brushroll remains on while cleaning with the
of the machine. The hose and tool. Do not allow cleaner to sit in one
door flips toward the location for an extended period of time, as damage
machine to open. to floor can result.

2 Insert the hose and 4

snap into place.
Be sure the colored
hose release clip
is facing out, away
from machine.
Press the spray trigger button to spray
the soiled area, then slowly move tool back
and forth over the area.
Release the trigger to suck up the dirty
3 solution. Work in small sections until the area
is clean.
When finished cleaning, turn the machine on
to suction up warm clean water to rinse the
inside of the hose and tool. Detach the hose
Attach the tool to the end of the hose. and tool and close the accessory hose door.
(Tools may vary by model.) Press the Let the hose and tool air dry before storing.
power button to turn machine on.

NOTE: If using the Deep Reach Tool or Pet Stain Tool be sure the needles of the
tool are pressed down into the carpet so the spray gets into the carpet fibers.

Cleaning with CleanShot®

1 2
Completely cover
the stain with
CleanShot® spray.
Allow the stain to
soak. To extract,
maneuver the foot
Spray will continue until you
turn it off. To turn CleanShot® of the machine
Press the CleanShot®
button with your foot. The off, press the button with over the stain to
window of the button will your foot. The window of the brush and remove.
be green and show an “I” button will be red and show an
symbol when it is on. “O” symbol when it is off.

14 www.BISSELL.com
 NEW! 2-in-1 Pet Upholstery Tool
*Make sure your clean tank has water & formula to use the tool in wet mode.

1 2

Dry
Suction
Channel
Dry Mode
(switch up)

Attach the tool and select dry mode

to first pick up dry debris and pet
Follow hose plug-in instructions from hair. The suction will be at the lower
steps 1 & 2 on page 14. part of the tool, near the dry cup.

DRY MODE NOTE: Use a “raking” motion to clean. Start with the tool farthest
away and rake in small increments as you bring the tool toward you. The rubber
nubs will help attract hair to the suction channel.

3 Empty the cup when 4 6

it fills with hair and
debris.
Take off the cup
to empty hair
and debris.

5
To reattach the cup, line
up the cup to the tool
Turn off the machine. indents, and rotate clock
Hold the cup and twist wise. The arrow will line
counterclockwise line up Remove hair up with the locked icon
the arrow with the unlock that may wrap when secured.
symbol and remove. around the filter.

7 8 9
Wet
Suction
Channel

Wet Mode
(switch
down) Replace to the tool by
To remove any hair or lining up the nozzle edge
To Deep Clean, move the trapped debris from the and snap into place.
switch to wet mode. Press nozzle, first turn off the Before storing, make sure
the trigger to spray your machine. Pull the nozzle all hair is removed from
water and formula; use tab away from the tool to the dry cup and nozzle
the top of the nozzle to remove and rinse under has been rinsed under
extract stains and odors. running water. running water.

WET MODE NOTE: Start from the area farthest away. Hold the trigger down, and
pull the tool toward you. Keep the tool in contact with the surface as you pull. You
will see extraction through the nozzle.

www.BISSELL.com 15
 Empty Dirty Water Tank
WARNING
To reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug from
electrical outlet before performing maintenance or troubleshooting.

1 2 3

Grab the handle and tank

To release dirty water Tilt the tank slightly with both hands and pull
tank, press down on the toward you. the dirty water tank up
colored tank handle. and away to remove.

4 For quick empty:

5
Pull the rubber tab
and tilt to pour.
(Located at the corner
of the top of the tank.) Clean the red filter
below the dirty
When closing the tank by wiping off
rubber tab, make any remaining dirt
sure all edges are or debris.
sealed tight.

For final clean and

rinse: Unscrew the ring
at the bottom of tank.
6
Gently remove the
float stack, rinse,
and clean. To return the dirty
tank: Angle the tank
Once clean, return float and insert bottom
stack into the tank by first. Then tilt the
lining up the arrows tank toward the
so they point at each machine and push
other. This is the only the top in until it
way the float stack will clicks into place.
fit into the tank.
With the arrows
aligned, the float stack Did You Know?
should lock into place. The Float Stack
Return the ring and is what prevents
twist to lock. Water your dirty
may leak if the ring is tank from
not fully tightened. overflowing.

16 www.BISSELL.com
 Cleaning Machine After Use
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from
electrical outlet before performing maintenance or troubleshooting checks.

To flush and rinse the See page 16 to clean the

machine: Turn the machine dirty tank from the water
First, fill the clean water on and press the trigger for that was just extracted.
tank with warm tap water 15 seconds while making Empty the clean water tank
and then empty it all to back and forth passes on a and let dry before storing.
rinse. Then fill again with section of carpet. Wipe your machine’s
warm tap water and return Finally, release the trigger exterior with a soft cloth.
the tank to the machine. and extract the water. Store machine in a
Twist cap back on tightly. protected dry area.

Brush Roll & Nozzle Care

NOTE: Be sure to clean the brush rolls and nozzle before storing your machine.
Follow these steps if your nozzle becomes clogged with hair or debris.

1 2 Remove the nozzle

from the foot:
scoop and grip the
Turn off and unplug Accessory Hose
the machine from the Door. Pull up to
grounded outlet. remove the nozzle.

3 Next, remove 4 At this point, the

the next layer, nozzle and brush
the brush roll roll cover can
cover, to reveal be rinsed under
the brush rolls. running water and
Press on the the nozzle clean
two release out tool can be
buttons and lift inserted to unclog
straight up. hair or debris.

NOTICE: To reduce the risk of a leaking condition, do not store unit where
freezing may occur. Damage to internal components may result.

www.BISSELL.com 17
 Brush Roll & Nozzle Care (Continued)
5 6 click

When finished, return the brush roll cover by

pushing it straight down. You will here a click from
each “push” button when the cover is pushed
Use the comb to brush out the down into place. Line up the nozzle from the edge
debris or hair from the brush rolls. near the floor and rotate to snap back into place.

Replacing Belts & Brush Rolls

What you will need: 1 Phillips screwdriver & 1 flathead screwdriver

While the machine is upright, unplug the machine and remove both tanks. Remove
the nozzle and brush chamber cover (see steps in Brush Roll & Nozzle Care). Press
the recline pedal and lay the machine on its back.

2 3 Turn the machine on its side and use

Use a flathead a Philips screwdriver to remove the
screwdriver and screw just underneath the wheel. Slide
press it into the slot the wheel down to remove.
at the back and
then front of the
belt access door.
Lift to remove the
Belt Access Door.

4 5
Lay the machine If the Gear Belt
back down on is broken, gently
its back. Use a remove it. If you
Phillips-head are replacing your
screwdriver to brush rolls, gently
remove the screw remove the belt.
on the brushroll
end cap.

18 www.BISSELL.com
Replacing Belts & Brush Rolls (Continued)
6
NOTE: To replace
brush rolls, remove
them from the
metal posts and
replace. Make sure
the metal post
goes completely
through the end of Align brush rolls with belt at other
the brush roll. The end. To ensure alignment, hold the
There are washers at end of one brush roll and twist.
the ends of the brush brush roll bristles
should be aligned The other brush roll rotates with it.
rolls, be careful that Check that washers are in place.
these do not fall off in a ‘V’ pattern as
pictured. Reassemble the belt and end cap,
or get lost. securing with screws you removed.

7 If the flat belt is broken, 8

gently remove the belt. Keep it wrapped
If it needs replacing for on the red pulley
any reason, the gear and adjust the
belt should already machine so it is
be removed before laying on it’s back
removing the flat belt. again. Use your
Rotate the machine thumb to stretch
back to its side. Feed the flat belt back
the new flat belt to wrap around
through the opening the metal axle.
so that it wraps around
the red pulley.

9 10

Resecure the Wheel and Belt Access Door:

Slide the wheel up back into the slot and Snap the Belt Access Door back
secure with the screw that was removed. down into place.

NOTE: See Step 6 on page 18 for how to put the brush roll cover and nozzle back
in place.

www.BISSELL.com 19
 Troubleshooting
WARNING
To reduce the risk of electric shock, turn power switch off and disconnect plug from
electrical outlet before performing maintenance or troubleshooting checks.

Problem Possible causes Remedies

Reduced or No Clean water tank may be empty Refill tank
Spray Through Clean water tank may not be Turn power OFF; remove and reseat tank
Foot of Machine seated completely

The hose to your machine is not primed or 1. With the machine off and unplugged, remove the nozzle from
may have lost prime the foot. Place a ball point pen in the black cylinder next to the
screw. When water bubbles up, remove the pen. Reassemble the
nozzle and hose
2. Hold end of hose below water level in tank to prime
No spray 3. With the clean tank full of water, the machine OFF and
through RECLINED, press the CleanShot® button ON and wait for the
hose & tool CleanShot® to drain for a few seconds; This will re-prime the
machine

Clean Water tank may be empty Refill the Clean Water Tank

Clean Tank may not be seated properly Turn power OFF; Remove and reseat the clean water tank

Clean Water tank may be empty Refill the Clean Water Tank

Clean Tank may not be seated properly Turn power OFF; Remove and reseat the clean water tank
No Spray The machine is not reclined Press the Recline pedal and bring the handle down to recline the
Through machine
CleanShot®
Pump may have lost prime With the machine off and unplugged, remove the nozzle from the
foot. Place a ball point pen in the black cylinder next to the screw;
When water bubbles up, remove the pen; Reassemble the nozzle
before cleaning again

CleanShot® CleanShot® button is not in the “OFF” Press the CleanShot® button to turn it off. The button window will
Continues Spray position show the color red and a “O” symbol when it is in the off position
When Machine
is Off
Dirty tank may not be seated properly Pick up the dirty tank and reseat so it fits in the unit

Dirty tank has picked up maximum amount Empty dirty tank

of dirty water and has reached full line

Rubber tab on dirty water tank is not sealed Check the rubber tab on the dirty water tank and press firmly on all
Loss of tight edges to secure it tightly (see step 4 on page 16 for detail)
suction
power Accessory hose door may not be closed Check the accessory hose door and make sure it is closed tightly – it
tightly in place should be locked into place

Nozzle may be clogged from pet hair or Use the nozzle clean out tool and follow steps on page 17 for
debris “Cleaning Nozzle”

Brush roll cover not fully snapped into place Remove the nozzle and brush roll cover; Follow step 6 from page 18
and make sure you hear both buttons click into place

Cleaning mode switch mistaken for power Press the red power button on the left side of the machine to turn
button the machine on
No power
Outlet may not be active Try plugging in a different device that uses a grounded outlet to test
for power from the outlet

Tank may have been over-filled 1. Make sure your tank has the water and formula in it that you’ve
prepared
Leaking tank Water may be caught in space between the 2. With the cap twisted ON tightly, hold your tank at an angle, over a
tank and the tank’s handle sink or drain, so any extra water can pour out of the space
3. Wipe the tank dry with a cloth

20 www.BISSELL.com
 Warranty
This warranty gives you specific legal rights, BISSELL IS NOT LIABLE FOR INCIDENTAL
and you may also have other rights which OR CONSEQUENTIAL DAMAGES OF ANY
may vary from state to state. If you need NATURE ASSOCIATED WITH THE USE OF
additional instruction regarding this warran- THIS PRODUCT. BISSELL’S LIABILITY WILL
ty or have questions regarding what it may NOT EXCEED THE PURCHASE PRICE OF
cover, please contact BISSELL Consumer THE PRODUCT.
Care by E-mail, telephone, or regular mail Some states do not allow the exclusion or
as described below. limitation of incidental or consequential
damages, so the above limitation or
Limited Five-Year Warranty exclusion may not apply to you.
Subject to the *EXCEPTIONS AND
EXCLUSIONS identified below, upon receipt *EXCEPTIONS AND EXCLUSIONS FROM
of the product BISSELL will repair or replace THE TERMS OF THE LIMITED WARRANTY
(with new or remanufactured components THIS WARRANTY IS EXCLUSIVE AND
or products), at BISSELL’s option, free of IN LIEU OF ANY OTHER WARRANTIES
charge from the date of purchase by the EITHER ORAL OR WRITTEN. ANY IMPLIED
original purchaser, for five years any WARRANTIES WHICH MAY ARISE
defective or malfunctioning part. BY OPERATION OF LAW, INCLUDING
THE IMPLIED WARRANTIES OF
See information below on "If your BISSELL MERCHANTABILITY AND FITNESS FOR
product should require service". A PARTICULAR PURPOSE, ARE LIMITED
This warranty applies to product used for TO THE FIVE YEAR DURATION FROM
personal, and not commercial or rental THE DATE OF PURCHASE AS DESCRIBED
service. This warranty does not apply to ABOVE.
fans or routine maintenance components Some states do not allow limitations on
such as filters, belts, or brushes. Damage or how long an implied warranty lasts so the
malfunction caused by negligence, abuse, above limitation may not apply to you.
neglect, unauthorized repair, or any other
use not in accordance with the User's Guide
is not covered.

NOTE: Please keep your original sales receipt. It provides proof of date of
purchase in the event of a warranty claim.

Service
If your BISSELL product should require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about
your warranty, contact BISSELL Consumer Care.

Website: Call:
www.BISSELL.com/service-centers BISSELL Consumer Care
1-800-237-7691
Monday – Friday 8am - 10pm ET
E-mail: Saturday 9am - 8pm ET
www.BISSELL.com/email-us Sunday 10am - 7pm ET

Please do not return this product to the store.

Other maintenance or service not included in the manual should be
performed by an authorized service representative.
For any questions or concerns, BISSELL is happy to be of service.
Contact us directly at 1-800-237-7691.

www.BISSELL.com 21
 Register your product today!
Registering is quick, easy and offers you benefits over the lifetime of your product.
You’ll receive:

BISSELL Rewards Points Product Support Reminders

Automatically earn points for and Alerts
discounts and free shipping on We’ll contact you with any
future purchases. important product maintenance
reminders and alerts.
Faster Service
Supplying your information now Special Promotions
saves you time should you need to Optional: Register your email
contact us with questions regarding to receive notice of offers,
your product. contests, cleaning tips and more!

Visit www.BISSELL.com/registration!

Visit us online at: BISSELL.com

When contacting BISSELL, have model number of
cleaner available.
We can’t wait
Please record your
Model Number: ____________________________
to hear from you!
Please record your
Purchase Date: ____________________________
We really do read
your comments, tweets,
NOTE: Please keep your original sales receipt. and posts.
It provides proof of purchase date in the event
of a warranty claim. See Warranty on page 21 Rate this product on
for details. BISSELL.com
or any of our retailer sites
Parts & Supplies and let us (and millions of
For Parts and Supplies, go to BISSELL.com and your closest friends)
enter your model number in the search field. know what you think!

For cleaning tips and more visit www.BISSELL.com or find us at:

BISSELL BISSELLClean BISSELLClean BISSELL BISSELL

©2017 BISSELL Homecare, Inc

Grand Rapids, Michigan
All rights reserved. Printed in China
Part Number 161-1761 01/17
Visit our website at: www.BISSELL.com
22 Scotchgard is a trademark of 3M