135 An 112018

Code No: 135AN
R16
JAWAHARLAL NEHRU TECHNOLOGICAL UNIVERSITY HYDERABAD
B. Tech III Year I Semester Examinations, November/December - 2018
ELECTRICAL MEASUREMENTS AND INSTRUMENTATION
(Electrical and Electronics Engineering)
Time: 3 hours Max. Marks: 75
Note: This question paper contains two parts A and B.

Part A is compulsory which carries 25 marks. Answer all questions in Part A. Part B
consists of 5 Units. Answer any one full question from each unit. Each question carries
10 marks and may have a, b, c as sub questions.
PART - A
(25 Marks)
1.a) For moving iron type instruments, give the expression for the deflecting torque. [2]
b) Describe errors in measuring instruments. [3]
c) Describe the basic principle of operation of a d.c. potentiometer. [2]
d) Explain why a potentiometer does not load the voltage source whose voltage is being
determined. [3]
e) Mention errors in dynamometer wattmeters. [2]
f) Explain driving and braking torques. [3]
g) Describe loss of charge method. [2]
h) Explain measurement of loss angle. [3]
i) What are advantages of electrical transducers? [2]
j) Explain gauge sensitivity. [3]
PART – B
(50 Marks)
2.a) Explain deflecting, control and damping torques.

b) Describe the principle of PMMC meters. [5+5]
OR
3.a) Explain the operation of electrometer type electrostatic voltmeters.
b) Describe the principle of attracted disc type E.S. voltmeters. [5+5]
4.a) Draw the circuit diagram of Crompton’s potentiometer and explain its working.
Describe the steps used when measuring an unknown resistance.
b) Power is measured with an a.c. potentiometer. The voltage across a 0.1Ω standard
resistance connected in series with the load is 0.35 – j0.10V. The voltage across 300:1
potential divider connected to the sypply is 0.8 + j0.15V. Determine the power
consumed by the load and the power factor. [5+5]
OR
5.a) Describe how high currents and voltages are measured with the help of instrument
transformers. Draw diagrams to illustrate your answer. Describe the advantages of
instrument transformers as regards extention of range of current and voltage on high
voltage a.c. systems.
b) A current transformer with 5 primary turns has a secondary burden consisting of a
resistance of 0.16Ω and an inductive resistance of 0.12Ω, when the primary current is
WWW.MANARESULTS.CO.IN
200A, the magnetizing current is 1.5A and the iron loss current is 0.4A. Determine any
expressions used, the number of secondary turns needed to make the current ratio 100:1
and also the phase angle under those conditions. [5+5]
6.a) Describe the construction of single phase dynamometer.
b) The total resistance of pressure circuit of a watt-meter is 4000Ω and the inductance of
the pressure coil circuit is 6.5mH. Give the shunted capacitor method of compensating
the inductance error and determine across what portion of the series resistance a 0.1µF
capacitor should be shunted to effective compensation. [5+5]
OR
7.a) Explain the operation of single phase induction type energy meter.
b) A 50A, 230V meter on full load test makes 61 revolutions in 37s. If the normal disc
speed is 520 revolutions per kWh, find the percentage error. [5+5]
8.a) Describe Carey Foster’s bridge.

b) A bridge is balanced at 1,000Hz and has the following constants: AB, 0.2µF pure
capacitance; BC, 500Ω pure resistance; CD, unknown; DA, R=300Ω in parallel with
C=0.1µF. Find the R and C or L constants of ard CD, considered as a series circuit.
[5+5]
OR
9.a) Explain the principle of Owen’s bridge.
b) An ac bridge has in arm AB a pure capacitance of 0.2µF; in arm BC, a pure resistance
of 500Ω; in arm CD, a series combination of R=50Ω and L=0.1H. Arm DA consists of
capacitor C=0.4µF in series with a variable resistor Rx, ω=5,000 rad/s. Find the value of
Rx to obtain bridge balance. [5+5]
10.a) Describe the principle of operation of LVDT.

b) An LVDT with a secondary voltage of 5V has a range of ±25mm.
i) Find the output voltage when the core is –18.75mm from centre,
ii) Plot the output voltage versus core position for a core movement going from
+18.75mm to -10mm. [5+5]
OR
11.a) Explain the force transducer with neat block diagram.
b) A transducer that measures force has a normal resistance of 300Ω, forms a four arm
strain gauge bridge and is excited by 7.5V DC. When the force of 0.1N is applied, all
the four strain gauge resistances are changed by 5.2Ω. Find the output voltage and
determine its sensitivity. [5+5]
---ooOoo---
WWW.MANARESULTS.CO.IN

135 An 112018

Uploaded by

Copyright:

Available Formats

135 An 112018

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

135 An 112018

Uploaded by

Copyright:

Available Formats

Code No: 135AN

Note: This question paper contains two parts A and B.

2.a) Explain deflecting, control and damping torques.

8.a) Describe Carey Foster’s bridge.

10.a) Describe the principle of operation of LVDT.

You might also like