™

T8.1
OWNERS MANUAL
 TABLE OF CONTENTS WARNINGS

Warnings.....................................................................................................................................................................................................3
WARNING/LIABILITY STATEMENT
This marker is not a toy and is surrendered by UTS, with the understanding that the purchaser assumes all liability from
Quick Start Guide.......................................................................................................................................................................................4 unsafe handling or any action that constitutes a violation of any applicable laws or regulations. UTS, shall not be liable
for personal injury, loss of property or life resulting from the use of this product under any circumstances, including any
intentional, reckless, negligent or accidental discharges.
T8.1 Diagram...............................................................................................................................................................................................5
All information contained in this manual is subject to change without notice. UTS, reserves the right to make changes
and improvements to products without incurring any obligation to incorporate such improvements in products
Magazine Diagram....................................................................................................................................................................................6 previously sold.
If you, as a user, do not accept liability, UTS, requests that you do not use a UTS marker. By using this UTS marker you
Operational Instructions...........................................................................................................................................................................7
release UTS, of any and all liability associated with its use.

Loading Magazine.....................................................................................................................................................................................8

Using First Strike Projectiles....................................................................................................................................................................9

WARNING: PAINTBALL GUNS AND PAINTBALL GUN
ACCESSORIES ARE NOT TOYS!
Setting Velocity........................................................................................................................................................................................11
- Careless use or misuse may result in serious bodily injury or death!
Cleaning & Maintenance .......................................................................................................................................................................12 - Eye protection designed for paintball must be worn by the user and all persons within range.
- Must be 18 years of age or older to operate or handle any paintball gun and paintball gun accessories without adult or
Warranty & Repairs.................................................................................................................................................................................13 parental supervision.
- Read and understand all cautions, warnings, and operating manuals before using any paintball gun or paintball gun accessory.
Assembly Guide.......................................................................................................................................................................................14 - Do not aim paintball gun at eyes or head of people or at animals.
- Paintball guns are to be used with paintballs only.
Gun Body Assembly ...............................................................................................................................................................................15 - To prevent fire or shock hazard, do not expose unit to rain or moisture.
- To prevent fire or shock hazard, do not immerse unit in liquids.
Engine & Firing Bolt Assembly .............................................................................................................................................................16
- To prevent fire or shock hazard, do not disassemble any electronic paintball device.
- The disposal of the battery if used to power this product may be regulated in your area.
Trigger Group Assembly ........................................................................................................................................................................17
- Please conform to all local or state regulations with regard to battery disposal.
- Use common sense and have fun.
Regulator Assembly ...............................................................................................................................................................................18
Any tampering with the unit voids your warranty. There are no consumer serviceable parts inside this unit. The use of non factory
Magazine Assembly................................................................................................................................................................................19 authorized components within this product may cause a fire or shock hazard.
IN NO EVENT SHALL SELLER BE LIABLE FOR ANY DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE, OR
CO2 Valve Assembly.................................................................................................................................................................................20 LOSSES OR EXPENSES RESULTING FROM ANY DEFFECIVE PRODUCT OR THE USE OF ANY PRODUCT.
WARNING: This product may contain chemicals known to the state of California to cause cancer and/or defects or other
Troubleshooting........................................................................................................................................................................................21 reproductive harm. Wash hands afer handling.
You must be at least 18 years of age to purchase this product. This product may be mistaken for a firearm by law enforcement
Registration Card.....................................................................................................................................................................................23 officers or others. Altering the color of the product or brandishing the product in public may be dangerous and may be
considered a crime.

2 | T8.1™ 3
 QUICK START GUIDE T8.1 DIAGRAM

Thank you for purchasing the First Strike 8.1 Pistol. Like any paintball marker, it is important that safety is
on the forefront of your mind at all times when using this product. Never operate the 8.1 without ASTM
compliant goggles or aim at anyone that is not wearing proper goggles intended for the game of Paintball.
The First Strike T8.1 is an advanced system that is suitable for all levels of play and will provide years of REAR SIGHT PROJECTILE VIEWPORT
service if the following steps are meticulously followed.
1. Before airing up, place 3 drops of First Strike approved oil at the top of the CO2 Air Cavity. BARREL
2. Insert the barrel into the front of the T8.1, and twist into locked position by inserting your finger
into the barrel and twisting. FRONT SIGHT

3. Insert 12gram CO2 cartridge into Magazine by placing in CO2 Cavity.

4. Engage the air source by twisting flip-knob base screw.
5. Insert magazine into grip firmly
6. Dry fire 3-4 times to distribute oil evenly through the marker.
7. Also chrono your T8.1 prior to use. VELOCITY
ADJUSTER

CATCH TECH TIPS AND INFO ON:

FRONT RAIL
SAFETY MOUNT

DON’T FORGET TO REGISTER! TRIGGER

Register your T8.1 at www.first-strike.com

MAGAZINE RELEASE
BUTTON

MAGAZINE

MODEL SPECIFICATIONS
CALIBER .68 HEIGHT 8”
ACTION SEMI-AUTO BARREL LENGTH 4”
POWER CO2 WEIGHT 2.7 LBS
LENGTH 11” MAGAZINE 8 ROUNDS

4 | T8.1™ 5
 T8.1 MAGAZINE DIAGRAM OPERATIONAL INSTRUCTIONS

GETTING STARTED
PROJECTILE Read this entire manual before using this launcher. Keep
RETAINER PIN your launcher pointed in a safe direction at all times.
1. SAFETY - Place the T8.1 in safe position by moving safety
so no red is visible. The safety is ambidextrous and can be
operated from either side of the T8.1.
* Visible red indicates that launcher
will discharge.

2. UNLOADING MAGAZINE - Ensure that there are no

projectiles in your marker by placing your hand under the
magazine, pressing the magazine release, and pulling the
PROJECTILE FOLLOWER magazine free from the T8.1.
TRACK

CO2 CAVITY

PROJECTILE FOLLOWER

3. REMOVING THE BARREL - Ensure that there are no

projectiles remaining in the marker by removing the
magazine and looking through the grip into the breach.
Then you can remove the barrel by pressing on the end
of the barrel and rotating it counterclockwise. Note the
channel in the barrel and the barrel lock in the receiver as
it slides free. To reattach the barrel, line up the channel
with the barrel lock, slide the barrel back in the receiver,
push on the end of the barrel, and turn clockwise until
the barrel locks into place. Pull on the end of the barrel to
ensure it is properly seated.

6 | T8.1™ 7
 OPERATIONAL INSTRUCTIONS OPERATIONAL INSTRUCTIONS

4. LOAD PROJECTILES - Place 8 projectiles into the LOAD PROJECTILE RED SPRING/SILVER SPRING
magazine from the top. The projectiles will be held in place
automatically by the projectile retainer pin. You can also When using First Strike™ projectiles, make sure the red
lock the ball pusher in the down position by pulling down magazine spring is installed. The silver spring is designed
on the ball pusher ears and locking them at the bottom of for use with traditional .68 caliber paintballs. While the red
the ball pusher track. spring can be used with traditional .68 caliber paintballs, its
higher tension increases the risk of the paintballs deforming
NOTE: FOR INSTRUCTIONS ON FIRST STRIKE ROUNDS, over time.
PLEASE REFERENCE PAGE 9.

FOLLOWER
EARS

LOADING FIRST STRIKE

Always load First Strike projectiles so rounded nose exits
barrel first. Always chronograph with First Strike before use
5. LOADING C02 CARTRIDGE - Obtain a 12 gram CO2 to ensure velocity is below 300 fps.
cartridge. Insert the CO2 cartridge into the CO2 slot of the
magazine with the small end of the CO2 cartridge pointing
up and into the puncture pin of the magazine. Next, rotate
the flip knob base screw clockwise quickly until the
cartridge has sealed.

FLIP KNOB
BASE SCREW

8 | T8.1™ 9
 OPERATIONAL INSTRUCTIONS OPERATIONAL INSTRUCTIONS

FIRING THE T8.1

1. If the CO2 cartridge has been punctured by the puncture pin and the magazine has
been inserted into the gun, then the T8.1 is now ready to fire. Point the T8.1 in a safe
direction, rotate the safety so red is visible, and pull the trigger.

NOTE: Extra magazines can be carried for quick reloads in the field.

UNLOADING THE T8.1

1. Place T8.1 in the safe mode and point in a safe direction. If all projectiles have been
fired, place hand under magazine and press magazine release with other hand.
Catch magazine so it does not fall on ground. Visually inspect the magazine well to
ensure all projectiles are clear from the T8.1. Visually inspect the projectile view port
to ensure all projectiles are clear.
2. If all projectiles have not been fired, follow above procedures but ensure that
you turn the T8.1 on its side while removing the magazine. The projectile that is in
the chamber will be free and can fall on the ground if the T8.1 is kept in a vertical
8. LOAD MAGAZINE - Place the magazine in the grip of position. Place your hand under the magazine well and capture the loose projectile
the T8.1 marker with the projectiles closest to the end of as you turn the T8.1 vertically.
the barrel. Once the mag has started into the grip, seat
it completely until has been secured by the magazine 3. Pull back on the projectile retainer pin to remove the projectiles from the magazine
release. and turn the flip knob base screw counterclockwise to free the CO2 cartridge from
the magazine.
NOTE: If magazine does not lock on first insertion, remove
it completely and reinsert. 4. Your T8.1 should now be free of any projectiles. Verify the T8.1 is on safe and store in
a safe and secure location.

SET VELOCITY
1. Insert provided 3/16” Allen wrench as depicted.
2. To increase velocity, tum clockwise. To decrease velocity
turn counter-clockwise.
3. Fire once to clear chamber after each adjustment, then
measure velocity of the second shot.
SAFETY TIP: Always measure marker’s velocity before playing
paintball. Never shoot at velocities in excess of 300 ft/s (91 .44
mls). Recommended velocity is 270 ft/s.

10 | T8.1™ 11
 T8.1 CLEANING & MAINTENANCE WARRANTY & REPAIRS

CLEANING First Strike® warranties to the original customer purchaser or current owner that this product
is free from defects in material and workmanship under normal use and service for a period of
• Never perform maintenance on a loaded or pressurized T8.1 marker. 12 months from the original date of purchase by the initial owner/purchaser.
• Remove all projectiles and CO2 cartridges from the magazine and marker prior to doing any For warranty to be effective, customer must return the First Strike® Warranty Registration
cleaning or maintenance. card that came with the product within thirty days of purchase or complete the online
warranty form. First Strike® agrees to repair or replace (at its discretion) any product within
• Never use petroleum based cleaning solvents or lubricants.
a reasonable period of time. This warranty does not cover o-rings, scratches, nicks, normal
• Do not use cleaning solvents that come in aerosol cans. wear and tear of parts, any modifications or normal fading of anodizing or damage caused by
dropping or hitting of products. This warranty shall not apply if it is shown by First Strike® that
• To clean the T8.1 marker, remove the barrel as described in the “Operational Instructions”. Use a .68 the consumer caused the defect or malfunction because of misuse. This warranty only covers
caliber soft nylon brush or 12 gauge patch tip with a soft cotton cloth to clean the barrel. Do not place original factory parts. Any modifications or tampering of original factory parts will not be
lubricant or water in the barrel of the T8.1. It is designed to be used with the barrel completely dry. covered by this warranty. Any damage caused by water will not be covered by this warranty.
• Keep the barrel of the T8.1 dry. If your paintball product requires repair, please package it carefully and send together with
• Wipe off any dirt or grime from the outside of the T8.1 with a dry cloth. your name, address, phone number, and a brief description of the malfunction to:
First Strike Warranty Support
OILING THE MARKER 2717 Ferguson Rd
Fort Wayne, IN 46809
IMPORTANT: Before performing any of the following instructions, remove magazine.
Point marker in safe direction and discharge until degassed. Phone Free: 260-478-2500
9:00am-4:00pm Eastern / Mon-Fri
FOR OPTIMUM PERFORMANCE, DO THE FOLLOWING MONTHLY: Note: Always remove the air source or degas the marker while not in use.
1. Place one drop of oil between trigger release and trigger rotator. (See Page 17)
2. Remove the regulator spring pad (See page 18) and oil the regulator spring pad O-Ring.
3. Remove the engine assembly (See page 16) and lightly grease the AC Cap O-Ring.
4. Place one drop of oil on CO2 O-Ring found at top of CO2 Valve and Magazine (See page 20).

OPERATIONAL CONSIDERATIONS

• The operational temperature range for the T8.1 Pistol is 37° F to 120°F.
• If the CO2 cartridge is punctured in a magazine, it should be replaced if the T 8.1 is not used for 24 hours.

12 | T8.1™ 13
 T8.1 ASSEMBLY DIAGRAM GUN BODY ASSEMBLY

ITEM NO. NAME ITEM NO. NAME ITEM NO. NAME ITEM NO. NAME

1 Gun Body Assembly 9 Safety-Left 1 Engine Assembly 9 Release Fork Screw

2 Handle 10 Safety-Right 2 8.1 Gun Body 10 Reg Body Screw
3 Trigger Pin 11 Safety Spring 3 Firing Bolt Assembly 11 SIGHT Set Screw
4 Handle Screw-Front 12 Safety Pin 4 Regulator/Trigger Assembly 12 Reg Body Internal Tooth Washer
5 Firing Bolt Spring 13 Front Handle Screw Washer 5 Front Sight 13 Reg Sealing/Reg Body O-RIng
6 T8.1 FS Barrel 14 Remote Plug Set Screw 6 Rear Sight 14 Gun Body Cap
7 Magazine Assembly 15 Rubber Nubbin 7 Ammo Release Fork 15 Reg Body Plug
8 Safety Bushing 8 Barrel Lock

15

1 11
11
11
5
12 5
NOTE: Be sure to install the engine, and push the bolt forward 2
2
14 towards nose of gun. It is critical that this is done before
10 2
reattaching the regulator assembly.
11
13 11
6
6
9
4 3 8
3 8
7
7

3 1 9
1 15 9
15
14
7 13
14
13

4
4 12
4 12

10
10

14 | T8.1™ 15
 ENGINE & FIRING BOLT ASSEMBLY TRIGGER GROUP

ITEM NO. NAME ITEM NO. NAME

1 Air Chamber Plug 1 Trigger

4
2 Air Chamber 2 Sear
3 AC Shock Absorber 3 Rotator
4 AC Cap O-Ring 1 4 Release
5 First Strike Firing Bolt 5 Push Rod
C
6 AC Plug O-Ring 6 6 Regulator Body
2 7 3 5 14
7 AC OD O-Ring 7 Trigger Spring Pin
8 Sear Spring
6
NOTE: Do not attempt to disassemble 4 bolt and firing pin (Item 2 9 Rotator Return Spring
5). The alignment is set by factory fixtures and cannot be 10 Release/Rotator Spring
reassembled outside the3 factory. 11 Trigger Cover
4 12 Push Rod O-Ring
D
13 Trigger Cover Screw
3
14 Trigger Return Spring

7
1 2 3 4

2 4 5 6 7 8

6 13
11
1
5
A

12
10
5

9
5 3
8 1
10 B

2
12

14

6 C

16 | T8.1™ 17
 REGULATOR MAGAZINE

ITEM NO. NAME ITEM NO. NAME ITEM NO. NAME ITEM NO. NAME

1 Regulator Body 9 Regulator Spring 1 Base Screw 10 Magazine Screw-UC

2 Regulator Adjuster 10 Regulator End Screw 2 CO2 Valve Housing Assembly 11 Magazine Screw-UR
3 Stem 11 Regulator Valve Sleeve 3 8.1 Magazine Spring 12 CO2 Base Screw Nut
4 Regulator Sealing Screw 12 Regulator Valve O-Ring 4 Retainer Pin Cap 13 Magazine Screw-LR
5 Reg Sealing/Reg Body O-Ring 13 Regulator End Screw O-Ring 5 Magazine Retainer Spring 14 Ball Pusher Assembly
6 Reg Body Plug 14 Regulator Valve Spring 6 Mag Ball Retainer Pin 15 Magazine Slide Base
7 Regulator Spring Pad O-Ring 15 Regulator Valve Ball 7 Magazine Body Nut 16 Main Magazine Body-L
8 C02 Stem O-Ring 16 Regulator Spring Pad 8 Magazine UC Nut 17 Main Magazine Body-R
9 Magazine Screw-LC

15
1
15
7 1 16 11
2 9 11
2 7 10 16 6
9 14
10
14 8 5 14

12 13
4
3 13
12
4 3 7
5 4

3 8 13 10
5 14 10

8 11 2
3 12 14 10 13

11 15 11
16
5
12
4
15
16
5 3
4
15
16 6
9 5

7
1
6 7
5 17

7
1
2
12

NOTE: O-Ring #12 is the same size and color as O-Ring #5 on 9

Page 20. This O-Ring is harder than the O-Ring on Page 20. 1
Relief valve is preset at the factory and is not user serviceable.
Consult factory or authorized service center for assistance.
13

18 | T8.1™ 19
 CO2 VALVE HOUSING TROUBLESHOOTING

ITEM NO. NAME PAINT BREAKAGE

1 C02 Valve Body If you experience more than a small number of broken paintballs, check the following:
6
2 C02 Puncture Tip
1. First, be sure that the marker is free of broken paintballs and other debris.
3 C02 Valve Spring
4 Housing O-Ring 2. Second, make sure that the barrel is locked in its correct position, and that both detents are
5 installed so that they catch a projectile as it enters the breach.
5 C02 Valve Spacer O-Ring
6 C02 Valve Cap 3. Third, make sure the maker is set to a reasonable velocity (never over 300 ft. per sec.)
7 C02 Seal 9 4. Check bolt assembly. Remove bolt from upper receiver and check for bad o-rings or debris
8 C02 Drum Valve
5. Check magazine for debris.
9 Valve Spacer
4 6. Load rounds in magazine (without CO2 cartridge installed) and engage PROJECTILE
RETAINER PIN - confirm that rounds can be ejected from the magazine without issue.

MY T8.1 HAS LOW VELOCITY OR DOES NOT FIRE!

NOTE: O-Ring #5 is the same size and 1. If running a remote, make sure your output pressure is above 800psi and is
color as O-Ring #12 on Page 18. This functioning properly.
O-Ring is softer than the O-Ring on 8
Page 18. 2. Remove bolt from upper receiver, and re-install. The T8.1 is designed to not function
if the bolt is installed incorrectly.

20 | T8.1™ 21
 NOTES
T8.1 WARRANTY REGISTRATION CARD:

NAME:

ADDRESS:

DATE OF PURCHASE:

SERIAL NUMBER:

Please detach from product manual,

place in stamped envelope and send to:

First Strike Paintball Warranty Support

2717 Ferguson Rd.
Fort Wayne, IN 46809

"

22 | T8.1™ 23
FIRST STRIKE®
Headquarters:
28101 Ballard Dr. Ste. F
Lake Forest, IL 60045
Manufacturing/Warranty
2717 Ferguson Rd
Fort Wayne, IN 46809

1-260-478-2500
service@first-strike.com
FIRST-STRIKE.COM

© 2017 United Tactical Systems. All rights reserved. This United Tactical Systems product is protected by
United States and International Patents. United Tactical Systems Trademarks, Designs and Copyrights are
protected by United States and International Law. For more information contact United Tactical Systems at
marketing@first-strike.com
Patent Info here: www.first-strike.com/patents 17/6/13