CFD-G35

SERVICE MANUAL US Model

Canadian Model
Ver 1.4 2002. 11
E Model
Australian Model

Model Name Using CD Section NEW

Similar Mechanism Tape Section CFD-G30
CD Mechanism Type KSM-213RDP
Optical Pick-up Type KSS-213R
Tape Transport Mechanism Type MF-V5-117

SPECIFICATIONS
AUDIO POWER SPECIFICATIONS Radio section Power requirements
POWER OUTPUT AND TOTAL Frequency range For CD radio cassette-corder:
HARMONIC DISTORTION FM: 87.5 - 108 MHz 120V AC, 60 Hz:
With 3.2-ohm loads, both channels driven AM: 530 - 1 710 kHz (US,Canadian,Mexican,Chilean and Peruvian
(US,Canadian,Mexican,Chilean and Peruvian models)
from 1 000 - 10 000 Hz; rated 2 W per 220 – 230V AC, 50 Hz:
channel-minimum RMS power, with no models)
(Argentina model)
more than 10 % total harmonic distortion : 531-1611kHz(Australian model)
230V AC, 50 Hz:
in AC operation. : 531-1611kHz(9kHz step)(Singapore model) (Other models)
Woofer with 4-ohm loads, driven at : 530-1610kHz(10kHz step)(Argentina model) 9 V DC, 6 size D (R20) batteries
Antennas For remote control:
50 - 150 Hz; rated 4 W minimum RMS
FM: Telescopic antenna 3 V DC, 2 size AA (R6) batteries
power, with no more 10 % total harmonic
AM: Built-in ferrite bar antenna Power consumption
distortion in AC operation.
AC 25 W
Cassette-corder section
Other specifications Recording system Battery life
4-track 2 channel stereo For CD radio cassette-corder:
CD player section
System Fast winding time FM recording
Compact disc digital audio system Approx. 115 s (sec.) with Sony cassette C-60
Sony R20P: approx. 4 h
Laser diode properties Frequency response
TYPE I (normal): 70 - 13 000 Hz Sony alkaline LR20: approx. 19 h
Material: GaAlAs
Wave length: 780 nm Tape playback
General
Emission duration: Continuous Speaker Sony R20P: approx. 1.5 h
Laser output: Less than 44.6 µW Full range: 10 cm (4 in.) dia., 3.2 Ω, cone type Sony alkaline LR20: approx. 7 h
(This output is the value measured at a distance (2)
of about 200 mm from the objective lens surface CD playback
Woofer: 8 cm (3 1⁄4 in.) dia., 4 Ω, cone type (1)
on the optical pick-up block with 7 mm Outputs Sony R20P: approx. 1.5 h
aperture.)
Headphones jack (stereo minijack) Sony alkaline LR20: approx. 3.5 h
Spindle speed
For 16 - 68 Ω impedance headphones
200 r/min (rpm) to 500 r/min (rpm) Dimensions
Power output
(CLV) Approx. 456 × 195 × 330 mm (w/h/d)
2 W + 2 W (at 3.2 Ω, 10% harmonic distortion
Number of channels (18 × 7 3⁄4 × 13 inches) (incl. projecting parts)
in DC operation)
2 Mass
Woofer:
Frequency response Approx. 6.4 kg (14 lb. 2 oz) (incl. batteries)
6 W (at 4 Ω, 10 % harmonic distortion in DC
20 - 20 000 Hz +1/–2 dB operation) Supplied accessory
Wow and flutter AC power cord (1)
Below measurable limit Remote control (1)
Design and specifications are subject to change
without notice.

CD RADIO CASSETTE-CORDER
9-873-631-05 Sony Corporation
2002K1600-1 Personal Audio Company
© 2002.11 Published by Sony Engineering Corporation
CFD-G35
Ver 1.3 2002. 09

TABLE OF CONTENTS
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be 1. SERVICING NOTES ······················································ 3
damaged by heat.
2. GENERAL ·········································································· 4
Flexible Circuit Board Repairing
• Keep the temperature of soldering iron around 270˚C 3. DISASSEMBLY ································································ 5
during repairing. 3-1. Cabinet (Front) Assy- 1 ················································ 5
• Do not touch the soldering iron on the same conductor of the 3-2. Cabinet (Front) Assy- 2 ················································ 6
circuit board (within 3 times). 3-3. CONTROL (POWER) , CONTROL (CD) ,
• Be careful not to apply force on the conductor when soldering HEADPHONE Board ··················································· 6
or unsoldering. 3-4. Panel Assy ····································································· 7
3-5. LCD Board, Panel (Upper) ··········································· 7
3-6. Panel (Upper) Assy- 1 ··················································· 8
3-7. Panel (Upper) Assy- 2 ··················································· 8
3-8. POWER, TRANS Board ··············································· 9
3-9. TUNER Board, Duct (Upper, Lower) ··························· 9
3-10. BATT COM, BATT Board ·········································· 10
3-11. MAIN Board- 1 ··························································· 10
3-12. MAIN Board- 2 ··························································· 11
3-13. Mechanism Deck Section (MF-V5-117) ···················· 11
3-14. CD Block Section (KSM-213RDP) ···························· 12
3-15. PDW, L-R/REG Board ················································ 12

4. ADJUSTMENTS ···························································· 13
4-1. Mechanical Adjustments ··············································· 13
4-2. Electrical Adjustments ·················································· 13

5. DIAGRAMS ······································································ 17
5-1. Circuit Boards Location ·············································· 17
5-2. Block Diagrams ·························································· 18
5-3. Printed Wiring Board – TUNER Section – ················ 20
5-4. Schematic Diagram – TUNER Section – ··················· 21
5-5. Printed Wiring Board – CD Section – ························ 22
5-6. Schematic Diagram – CD Section – ··························· 23
5-7. Printed Wiring Board – TC Section – ························· 24
5-8. Schematic Diagram – TC Section – ···························· 24
5-9. Printed Wiring Board – MAIN Section – ··················· 25
5-10. Schematic Diagram – MAIN Section (1/2) – ············· 26
5-11. Schematic Diagram – MAIN Section (2/2) – ············· 27
5-12. Printed Wiring Board – AMP Section – ····················· 28
5-13. Schematic Diagram – AMP Section – ························ 29
5-14. Printed Wiring Board – CONTROL Section – ··········· 30
5-15. Schematic Diagram – CONTROL Section – ·············· 31
5-16. Printed Wiring Board – POWER Section – ················ 32
5-17. Schematic Diagram – POWER Section – ··················· 33
5-18. IC Pin Function Description ······································· 36

6. EXPLODED VIEWS ······················································ 38

6-1. Cabinet (Front) Section ··············································· 38
6-2. Cabinet (Rear) Section ················································ 39
6-3. Cabinet (Upper) Section ············································· 40
6-4. Mechanism Deck Section- 1 (MF-V5-117) ··············· 41
6-5. Mechanism Deck Section- 2 (MF-V5-117) ··············· 42
6-6. CD Mechanism Section (KSM-213RDP) ··················· 43

7. ELECTRICAL PARTS LIST ······································· 44

SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.

2
 CFD-G35
SECTION 1
SERVICING NOTES

SAFETY CHECK-OUT NOTES ON HANDLING THE OPTICAL PICK-UP

BLOCK OR BASE UNIT
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer: The laser diode in the optical pick-up block may suffer electrostatic
Check the antenna terminals, metal trim, “metallized” knobs, screws, breakdown because of the potential difference generated by the
and all other exposed metal parts for AC leakage. Check leakage as charged electrostatic load, etc. on clothing and the human body.
described below. During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
LEAKAGE parts.
The flexible board is easily damaged and should be handled with
The AC leakage from any exposed metal part to earth ground care.
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes). NOTES ON LASER DIODE EMISSION CHECK
Leakage current can be measured by any one of three methods. The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
1. A commercial leakage tester, such as the Simpson 229 or RCA up block. Therefore, when checking the laser diode emission,
WT-540A. Follow the manufacturers’ instructions to use these observe more than 30 cm away from the objective lens.
instruments.
CHUCK PLATE JIG ON REPAIRING
2. A battery-operated AC milliammeter. The Data Precision 245 On repairing CD section, playing a disc without the CD lid, use
digital multimeter is suitable for this job. Chuck Plate Jig.
• Code number of Chuck Plate Jig : X-4918-255-1
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)

To Exposed Metal
Parts on Set

LASER DIODE AND FOCUS SEARCH OPERATION

AC
Voltmeter CHECK
0.15 µF 1.5 kΩ
(0.75 V) 1. Press CD open knob.
2. Open the lid for CD.
3. Push on SWITCH (S801) as following figure.
4. Confirm the laser diode emission while observing the objecting
lens. When there is no emission, Auto Power Control circuit or
Earth Ground
Optical Pick-up is broken.
Fig. A. Using an AC voltmeter to check AC leakage. Objective lens moves up and down once for the focus search.

Insert a precision
screw driver and push
SWITCH (S801)

3
CFD-G35
SECTION 2
GENERAL This section is extracted
from instruction manual.

Location of controls
Inserting a cassette Loading a CD
With the side you want to
play facing upward

With the labeled side up

VOLUME –, +*

MODE DISPLAY
ENTER Z PUSH
TUNE –, + MEMORY OPEN/CLOSE

SOUND u* x

POWER

SLEEP ., >
PRESET –, +
BAND
i AUTO PRESET

POWER DRIVE Display OPR/BATT

WOOFER
Remote sensor

Display
D E
Total track number Total playing time Programmed track Playing order

Remote Control

SLEEP

FUNCTION POWER

Number buttons
About CD-Rs/CD-RWs
This player can play CD-Rs/CD-RWs
recorded in the CD-DA format*, but
MODE playback capability may vary depending on
the quality of the disc and the condition of
BAND VOL +*, – the recording device.
* CD-DA is the abbreviation for Compact
TUNE+, – Disc Digital Audio. It is a recording
x standard used for Audio CDs.
N
.,> If you have any questions or problems
X
concerning your player, please consult your
WOOFER nearest Sony dealer.
SOUND

*The button has a tactile dot.

4
 CFD-G35
SECTION 3
DISASSEMBLY
• The equipment can be removed using the following procedure.

Set

CABINET (FRONT) ASSY-1

(page 5)

CABINET (FRONT) ASSY-2 CONTROL (POWER), CONTROL (CD), HEADPHONE BOARD

(page 6) (page 6)

PANEL ASSY LCD BOARD, PANEL (UPPER)

(page 7) (page 7)
PANEL (UPPER) ASSY-1
(page 8)

PANEL (UPPER) ASSY-2 MAIN BOARD-1 MAIN BOARD-2 PDW, L-R/REG BOARD
(page 8) (page 10) (page 11) (page 12)

MECHANISM DECK SECTION (MF-V5-117)

POWER, TRANS BOARD
(page 11)
(page 9)

TUNER BOARD, DUCT (UPPER, LOWER) CD BLOCK SECTION (KSM-213RDP)

(page 9) (page 12)

BATT COM, BATT BOARD

(page 10)

Note : Follow the disassembly procedure in the numerical order given.

3-1. Cabinet (Front) Assy- 1

5 screw
+BVTP 3 × 10
4 Open the CD lid in the
direction of the arrow.

3 eight screws
+BVTP 3 × 14

2 two screws
+BVTP 3 × 20
detal view

1 Remove the battery case lid

in the direction of the arrow.

5
CFD-G35

3-2. Cabinet (Front) Assy- 2

2 flexible flat cable

(from MAIN board CNP804)

1 Remove the cabinet (front) assy 4 CNP391

in the direction of the arrow. HEADPHONE board (from PWD board KH353)

5 CNP393
(from L-R/REG board KH374)

3 flexible flat cable

(from MAIN board CNP801)

MAIN board

3-3. CONTROL (POWER) , CONTROL (CD) , HEADPHONE Board

2 CONTROL (POWER) board,

button (power)

1 two screws
+BVTP 2.6 × 10

3 screw
+BVTP 3 × 10

4 HEADPHONE board

5 two screws
+BVTP 2.6 × 10

6 CONTROL (CD) board,

button (CD)

6
 CFD-G35

3-4. Panel Assy 1 screw

+BVTP 3 × 10

5 panel assy 3 flexible flat cable

(from MAIN board CNP804)

4 dlexible flat cable

(from MAIN board CNP801)

2 four screws
+BVTP 3 × 10

3-5. LCD Board, Panel (Upper)

!™ panel (upper)

7 two screws
+BVTP 2.6 × 10
8 two screws
+BVTP 2.6 × 10

5 button (PDW)

4 button (VOL)
!¡ LCD board

9 panel (front) section

3 flexible flat cable

6 light guide plate (from MAIN board CNP804)
(PWD)
2 CONTROL (VOL) board

0 flexible flat cable

(from MAIN board CNP801)

1 six screws
+BVTP 2.6 ×10

7
CFD-G35

3-6. Panel (Upper) Assy- 1

7 Open the cassette holder assy
in the direction of the arrow.

5 Open the CD lid in the

direction of the arrow.

6 Push STOP/EJECT button. 4 Remove two harnesses

in the direction of the arrow.

2 CNP903
(from MAIN board KH301)

3 Remove two harnesses 1 CNP1

in the direction of the arrow. (from MAIN board KH801)

3-7. Panel (Upper) Assy- 2

2 five screws
+BVTP 3 × 10

1 four screws
+BVTP 3 × 10

5 handle

4 Remove the panel (upper) assy

in the direction of the arrow.

3 Move the telescopic antenna in

the direction of the arrow.

8
 CFD-G35

3-8. POWER, TRANS Board

6 five screws
+BVTP 3 × 10

1 CNP902
(from BATT board KH951)
8 POWER board,
4 two screws TRANS board
+BVTP 3 × 10

power transformer
(T901)

2 Remove harnesses in the direction

of the arrow.

7 chassis
(trans) 5 four screws
+BVTP 3 × 10
3 screw
+BVTP 3 × 10

3-9. TUNER Board, Duct (Upper, Lower)

8 seven screws
0 duct (upper)
+BVTP 2.6 × 8

9 duct (lower)
2 two screws
7 two screws +BVTP 3 × 10
+BVTP 3 × 10

4 TUNER board

6 bracket (woofer)

3 chassis (TU)
5 screw 1 screw
+BVTP 3 × 10 +BVTP 3 × 10

9
CFD-G35

3-10. BATT COM, BATT Board

1 CNP902
(from BATT board KH951)

2 Remove harnesses in the direction

of the arrow.

BATT board

6 BATT COM board

9 battery
terminal
8 battery terminal

5 screw
4 BATT board
3 × 8 (DIA, 10),+WH
7 three screw
3 screw +BVTP 3 × 10
3 × 8 (DIA, 10),+WH

3-11. MAIN Board- 1

0 four screws
+BVTP 3 × 10

!¡ MAIN board

9 CNP302
3 CD door sw
(S801) L-R/REG board

5 CNP352

4 CNP351

PDW board

8 CNP371

2 flexible flat cable 7 CNP372

CNP802
6 CNP373
1 flexible flat cable
CNP805

10
 CFD-G35

3-12. MAIN Board- 2

5 MAIN board

PDW board

CNP353 L-R/REG board

CNP374
chassis (CD)

1 from TUNER board CNP1

4 from POWER board CNP903

2 from HEADPHONE board CNP391

3 from HEADPHONE board CNP393

3-13. Mechanism Deck Section (MF-V5-117)

2 screw
1 flexible flat cable
+PTT 2 × 6
(from MAIN board CNP805)

3 TC board

4 three screws
+BVTP 3 × 10

5 mechanism deck section

(MF-V5-117)

11
CFD-G35

3-14. CD Block Section (KSM-213RDP)

2 Remove solderings
from the four points. 1 flexible flat cable
(from MAIN board CNP802)

4 CD board

3 flexible flat cable

CNP701 5 four screws
2.6 × 10 (DIA, 10),+WH

6 CD block section
(KSM-213RDP)

3-15. PDW, L-R/REG Board

5 three screws
+BVTP 3 × 10 2 clamp
1 screw
+BVTP 3 × 10
3 two screws
+BVTP 3 × 10
6 PDW board,
Chassis (HS, R)

4 L-R/REG board,
Chassis (HS, L)

12
 CFD-G35
SECTION 4
ADJUSTMENTS
4-1. Mechanical Adjustments 4-2. Electrical Adjustments

PRECAUTION TAPE SECTION 0dB = 0.775V

1. Clean the following parts with a denatured-alcohol-moistened Standard Output Level
swab : Output terminal HP OUT
record/playback head pinch roller load impedance 32 Ω
erase head rubber belts
output signal level 0.25V (–10dB)
capstan
2. Demagnetize the record/playback head with a head demagne-
Test Tape
tizer. (Do not bring the head demagnetizer close to the erase
Type Signal Used for
head.)
3. Do not use a magnetized screwdriver for the adjustments. WS-48A 3kHz, 0dB Tape Speed Adjustment
4. The adjustments should be performed with the rated power
supply voltage (9V) unless otherwise noted.
Tape Speed Adjustment
Procedure :
Torque Measurement
Mode : Playback
Torque Torque Meter Meter Reading
test tape digital frequency
1.77 – 5.88 mN•m WS-48A counter
Forward CQ-102C (18 – 60 g•cm) (3kHz, 0dB) 32Ω
(0.25 – 0.83 oz•inch)
0.1 – 0.49 mN•m set
Forward
CQ-102C (1.0 – 5.0 g•cm)
Back Tension
(0.014 – 0.069 oz•inch)
J391 ( i )
4.42 – 9.31 mN•m
Fast Forward CQ-201B (45 – 95 g•cm)
Adjustment so than the value on the digital frequency counter is
(0.62 – 1.32 oz•inch) 3,000 Hz.
4.42 – 9.31 mN•m
Rewind CQ-201B (45 – 95 g•cm) Adjustment Value : 3,000Hz
(0.62 – 1.32 oz•inch) Standard Value : 2,940 - 3,060Hz

Tape Tension Measurement Frequency difference between the beginning and the end of the tape
Torque Meter Meter Reading should be within 1.5% (45Hz).
more than 60g
CQ-403A
(more than 2.12 oz)
Adjustment Location : Mechanism deck

Tape speed adjustment

control inside motor

13
CFD-G35
Ver 1.1 2002. 05

TUNER SECTION 0dB = 1 µV AM IF ADJUSTMENT

Adjust for a maximum reading on level meter.
AM Section T1 450 kHz
Function switch : AM no mark : EXCEPT AUS,
AR, SP
AM RF signal Put the lead-wire ( ) : AUS, SP
generator antenna close to < > : AR
the set. AM FREQUENCY COVERAGE ADJUSTMENT
530 kHz 1,710 kHz
Frequency Display (531 kHz) (1,611 kHz)
30% amplitude modulation by 400Hz <530 kHz> <1,610 kHz>
signal. 5.3 ± 0.8V
Output level : as low as possible Reading on Digital voltmeter 1.0 ± 0.1 V (4.8 ± 0.8V)
<4.8± 0.8V>
Adjustment Part L4 <confirmation>
FM Section no mark : EXCEPT AR
Function switch : FM < > : AR
AM TRACKING ADJUSTMENT
FM RF signal
generator
Adjust for a maximum reading on level meter.
L3 CT3
0.01µF 620 kHz <621kHz> 1,400 kHz <1,404 kHz>
telescopic
antenna
terminal FM IF ADJUSTMENT
33.75kHz frequency deviation by Adjust for a maximum reading on level meter.
1kHz signal. T2 10.7 MHz
Output level : as low as possible

FM FREQUENCY COVERAGE ADJUSTMENT

Frequency Display 87.5 MHz 108 MHz
Reading on Digital voltmeter 1.3 ± 0.4 V 3.0 ± 0.3 V
Adjustment Part <confirmation> L2
• Connecting Level Meter (FM and AM)
FM TRACKING ADJUSTMENT
level meter
(range: 0.5–5 V ac)
Adjust for a maximum reading on level meter.
L1 CT1
32 Ω
87.5 MHz 108 MHz
set
Abbreviation
AR : Argentina model.
J391 ( i ) AUS : Australian model.
SP : Singapore model.

• Connecting Digital Voltmeter (FM and AM) Adjustment Location : TUNER board (See page 16)

digital
voltmeter

100 kΩ
TP CV

• Repeat the procedures in each adjustment several times, and the

frequency coverage and tracking adjustments should be finally
done by the trimmer capacitors.

14
 CFD-G35

CD SECTION Focus Bias Check

1. Connect an oscilloscope between TP RF and TP VREF on
CD Test Mode CD board.
• How to put the set into CD test mode 2. Insert the test disc (YEDS-18).
1. Press the POWER button to turn the power on. 3. Set the CD test mode.
2. Insert the test disc (YEDS-18). (Part No. : 3-702-101-01) 4. Press the u button three times (LPC ON).
(Function is set to CD.) 5. Confirm that the oscilloscope waveform is as shown in the figure
3. Set the CD test mode by momentary shorting both sides of below. (eye pattern)
TEST- 1 on MAIN board. A good eye pattern means that the diamond shape (◊) in the
4. Press the x button two times. The set is set to the CD test center of the waveform can be clearly distinguished.
mode. 6. Press the u button.(LPC OFF)
(The message 80 is displayed.) 7. Perform confirmation in step 4 again.

• How to release the CD test mode • RF Signal Reference Waveform (eye pattern)
Turn the power off.
VOLT/DIV : 200mV
[MAIN BOARD] (Conductor side) TIME/DIV : 500 ns

RF level
IC801 0.85 ± 0.2 Vp-p (LPC ON)
IC803
0.95 ± 0.4 Vp-p (LPC OFF)

IC802

IC321 IC805 [CD BOARD] (Conductor side)

TP VREF TP TE TP RF
TEST-1

Traverse Waveform Check

1. Connect an oscilloscope between TP TE and TP VREF on IC701
CD board.
2. Set the CD test mode.
3. Press the u botton to play the test disc (YEDS-18).
4. Confirm that the center of the traverse waveform will be at 0V.
5. Confirm that the peak-to-peak voltage value of the traverse
waveform meets the specification.
6. Release the CD test mode.

• Traverse waveform
VOLT/DIV : 200mV
TIME/DIV : 1 ms
symmetry

0V
B

A (DC voltage)

A = 0 ± 220 mV
B = 0.95 ± 0.55 Vp-p

15
CFD-G35

Adjustment Location :

[TUNER BOARD] (Component side)

L1: FM Tracking Adjustment

CT1: FM Tracking Adjustment L3: AM Tracking Adjustment

CNP1

CT3: AM Tracking Adjustment

T2: FM IF Adjustment L4: AM Frequency Coverage Adjustment
T1: AM IF Adjustment L2: FM Frequency Coverage Adjustment

(Conductor side)

IC2 IC1

TP CV
AM/FM Frequency Coverage Adjustment

16
 CFD-G35
SECTION 5 Ver 1.3 2002. 09
DIAGRAMS
5-1. Circuit Boards Location Note on Printed Wiring Boards: Note on Schematic Diagram:
• X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. p: pF.
• f : internal component. 50 WV or less are not indicated except for electrolytics
• : Pattern from the side which enables seeing. and tantalums.
CONTROL (VOL) board (The other layers' patterns are not indicated.) • All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• f : internal component.
CONTROL (POWER) board • 2 : nonflammable resistor.
BATT COM board • C : panel designation.

Note: Note:
The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
HEADPHONE board specified. pièce portant le numéro spécifié.

• A : B+ Line.
• H : adjustment for repair.
• Total current is measured with no cassette installed.
• Power voltage is dc 9 V and fed with regulated dc power
supply from battery terminal.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
LCD board TUNER board Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
f : AM
E : PB
BATT board CONTROL (CD) board a : REC
J : CD
• Abbreviation
AR : Argentina model.
AUS : Australian model.
CND : Canadian model.
E92 : Chilean and Peruvian model.
CD board L-R/REG board MX : Mexican model.
SP : Singapore model.
MAIN board
POWER board
• WAVEFORMS
– TUNER Section – – TC Section – – CD Section –

1 IC2 w; (XOUT) 2 Q301 collector (TAPE REC) 3 IC701 rk (XOUT)

1.4 Vp-p
13.3 µs 3.1 Vp-p 4.2 Vp-p
18 µs 59 ns
500 mV/DIV, 4 µs/DIV 1 V/DIV, 10 µs/DIV 1 V/DIV, 20 ns/DIV

PDW board
– MAIN Section –

4 IC801 ua (XT2) 5 IC801 ug (X2)

TRANS board TC board

3.6 Vp-p 3.7 Vp-p

30.5 µs 238 ns
1 V/DIV, 10 µs/DIV 1 V/DIV, 100 ns/DIV

17 17
CFD-G35
Ver 1.3 2002. 09
5-2. Block Diagrams
MAIN Section

IC301
PRE AMP
TUNER/CD L OUT L IN
SECTION B 24

TUNER/CD L-CH RADIO IC371

SECTION A 22
BUFFER
IC321 POWER AMP
SOUND/VOLUME
TAPE AMP 7dB
L R-CH J391
20 1 VIN1 OUT1 17 12 3
TAPE STBY
Q171
8
MUTE
R-CH

SC
SI
VDD(SW)
PB AMP 14 13 SP391
HEAD
5 SPEAKER (L-CH)
REC AMP
L-CH 26dB Q321
AMP Q351
4 BASS AGC
R-CH REF REC TAPE LINE SP392
R-CH 6 21 15 17 IC351 SPEAKER (R-CH)
WOOFER
POWER AMP
Q322
12
LPF 3 SP393
T301 13
CD 3.3V WOOFER
Q301
10
(MAGNET) BIAS Q354 5
OSC 11
AGC
STBY
S301 8
REC PB AUDIO 6V

PB

VDD(SW) POWER AMP +9V

REC
CNJ901

Q954
AU +6V
+6V REG
Q972
CD/RADIO +6V
CD +6V REG (AC IN)
Q956
CD +3.3V
+3.3V REG
Q955
DRY BATTERY
SIZE "D"
(IEC DESIGNATION R20)
M321 VDD(SW) CND,AUS,AR,SP 6PCS, 9V
D951
CAPSTAN/REEL M VDD(5W)
MOTOR D952
9V
IC803 D953 Q952 T901
CD/RADIO+6V VDD(SW) POWER
S322 EEP ROM SWITCH
MOTOR D957 Q951
3.3V
5 6 BUFFER D901-904
S321 RECT
PLAY Q953
INV
µ COM VDD
51 39 67 36 35 65 64 34 30 77 66
WOOFER ON/OFF

P-CON
SDA
SCL
TC-PLAY

A-MUTE
V-DATA
V-CLOCK
TAPE
REC

CD IC805 IC802

70 XT1 1 RESET 2 3 +3.3V 2

RESET 76 REG
X802
32.768kHz
71 XT2 IC801(2/2) D807
IC891 • R-CH is omitted due to same as L-CH.
SYSTEM CONTROL
D806 • Signal Path
74 X1 RMC 48 1 REMOTE 2
X801 CONTROL
4.19MHz : FM
75 X2 REG CHK 49
W-LED1
KEY-3
KEY-1

KEY-2

: CD
WP

SEG0 SEG17 COM0 COM3

50 43 44 45 79 10 27 6 9
: PB
VDD(SW)
Q810 : REC
TEST-1
LED DRIVE LCD891 D893
LIQUID CRYSTAL OPR/BATT
FUNCTION FUNCTION DISPLAY PANEL
SWITCH SWITCH D401
POWER DRIVE
S401,402 S409-416 WOOFER
S404-408

18 18
 CFD-G35
TUNER/CD Section

ANT1 RADIO 6V
FM T2
TELESCOPIC IC1 T2
ANTENNA FM IF
FRONT-END
IF AMP,DET,FM MPX
10 23 5
QUAD VCC1 VCC2

FM RF I FM MIX OUT CF2 FM IF FM

2 MIX 4 7 DET
RADIO 6V
MPX L-CH MAIN
FM/AM MPX
16 15
FM
MUTE
12 A SECTION
L1 T1 BUFFER MPX 11 R-CH
FM RF O
24 CF4 AM IF AM
L1, CT1 RADIO 6V 6 DET
D1 CT1
FM T1
TRACKING L2 AM IF IF
FM OSC FM BUFFER
21 OSC
L2

ST IND
MO/ST
D2

BAND
FM
FREQUENCY IC2 IFOUT
6V PLL
COVERAGE L3 14 18 13 17
D3 FERRITE-ROD
ANTENNA 14 VDD
L3, CT3 AM RF AM
22 MIX OSC
AM CT3 19 12 FM
TRACKING
11 AM MO/ST 13
RADIO 6V ST IND 8
L4
BAND 7
AM AM OSC AM
L4 20
FREQUENCY OSC
COVERAGE
RADIO 6V
20 XO IC801(1/2)
X1 SYSTEM CONTROL
75kHz
19 XI IF IN 10 57 R-MUTE

18 LP OUT
DO 4 60 R-COUNT
VDD(SW) LPF 17 LP IN DI 2 62 R-DATA
CL 3 61 R-CLK
16 PD CE 1 63 R-CE

OPTICAL PICK-UP IC701

BLOCK RF AMP,D/A CONV

VC 11 VREF
VCC
A L OUT MAIN
B
8 FIN2 L OUT 42 B SECTION
7 FIN1
C
R OUT 45 R-CH
D
E
9 TIN1
F
10 TIN2
Q701
DO 64 53 C-DO
LD LD
80 LD DI 63 54 C-DI
DRIVE
CL 62 55 C-CLK
GND CE 61 56 C-CE
DRF 4 58 C-DRF S801
FSEQ 31 46 C-FSEQ Z PUSH
PD OPEN/CLOSE
79 PD WRQ 65 52 WRQ
VR RES 66 59 C-RES C-DOOR 40
IC702
MOTOR/COIL DRIVE
F+
17 F+ F IN 19 21 FDO
FOCUS
COIL F- S701
18 F- CONT1 72 LIMIT
IN SW
T+
12 T+ T IN 9 20 TDO
TRACKING • R-CH is omitted due to same as L-CH.
XIN 49
COIL T-
11 T- X701 • Signal Path
16.93MHz
XOUT 48
: FM
26 SL+ SL IN 25 23 SLDO
M702
SLED M
MOTOR : CD
27 SL-

2 SP+ SP IN 3 22 SPDO
M701
SPINDLE M
MOTOR
1 SP- MUTE 7 25 CONT4

19 19
CFD-G35
Ver 1.3 2002. 09
5-3. Printed Wiring Board – TUNER Section – • See page 17 for Circuit Boards Location.

AUS,AR,SP

IC1 IC2

US,CND,E,MX
25
AUS,AR,SP

US,CND,E,MX

• Semiconductor
Location
25
Ref. No. Location
D1 B-2
D2 B-3
D3 B-3
D10 B-1
D11 B-1

IC1 A-2
IC2 A-4

20 20
 CFD-G35
Ver 1.3 2002. 09
5-4. Schematic Diagram – TUNER Section – • See page 34 for IC Block Diagrams. • See page 17 for Waveforms.

US,CND,E,MX
AUS,AR,SP
JC24

US,CND,E,MX

C14,C15
0.022:US,CND,E,MX
0.01:AUS,AR,SP
AUS,AR,SP

21 21
CFD-G35
5-5. Printed Wiring Board – CD Section – • See page 17 for Circuit Boards Location.

IC702

(LIMIT IN)

25

IC701

22 22
 CFD-G35
5-6. Schematic Diagram – CD Section – • See page 34,35 for IC Block Diagrams. • See page 17 for Waveforms.

23 23
CFD-G35
Ver 1.1 2002. 05
5-7. Printed Wiring Board – TC Section – 5-8. Schematic Diagram – TC Section –
• See page 17 for Circuit Boards Location. • See page 35 for IC Block Diagrams.
• See page 17 for Waveforms.

IC301

25
(MAGNET)

(MAGNET)

24 24
 CFD-G35
Ver 1.3 2002. 09
5-9. Printed Wiring Board – MAIN Section – • See page 17 for Circuit Boards Location.

• Semiconductor
Location
28 28
Ref. No. Location
D320 C-1

CND,AUS,AR,SP
D323 C-4
D324 C-1
D806 F-5
CND,AUS,AR,SP D807 F-5
D808 G-5
28 D951 A-4
D952 A-4
D953 A-4
D955 A-3

CND,AUS,AR,SP
28
D956 A-3
CND,AUS,AR,SP
D957 B-3
28
IC321 C-3
IC801 F-4
IC802 E-4
32 IC803 E-4
IC805 G-3

Q321 B-2
Q322 B-1
Q810 H-3
EXCEPT AUS

Q951 A-4
Q952 A-4
Q953 A-4
IC321 Q954 A-3
Q955 A-3
Q956 A-2

20

IC802 IC891

24
22

IC803

IC805 IC801

20

6 7 8 9

30

25 25
CFD-G35
Ver 1.3 2002. 09
5-10. Schematic Diagram – MAIN Section (1/2) – • See page 34 for IC Block Diagrams.

EXCEPT AUS

CND,AUS,AR,SP BUFFER

26 26
 CFD-G35
Ver 1.3 2002. 09
5-11. Schematic Diagram – MAIN Section (2/2) – • See page 36 for IC Pin Function Description.

0:US,CND,E,MX
470:SP
4.7k:AR
10k:AUS

0:EXCEPT SP
220:SP

27 27
CFD-G35
Ver 1.3 2002. 09
5-12. Printed Wiring Board – AMP Section – • See page 17 for Circuit Boards Location.

AUS,AR,SP
AUS,AR,SP
C362

C364
US,CND,E,MX

AUS,AR,SP C363
US,CND,E,MX

IC351

25 25

25

25

25 IC371

28 28
 CFD-G35
Ver 1.3 2002. 09
5-13. Schematic Diagram – AMP Section –

US,CND,
E,MX
C365 US,CND,
0.1 E,MX

C363 AUS,AR,SP
0.1

AUS,AR,SP C364 0.1 C362 0.1

29 29
CFD-G35
5-14. Printed Wiring Board – CONTROL Section – • See page 17 for Circuit Boards Location.

25

SLEEP POWER

30 30
 CFD-G35
5-15. Schematic Diagram – CONTROL Section –

31 31
CFD-G35
5-16. Printed Wiring Board – POWER Section – • See page 17 for Circuit Boards Location.

25

32 32
 CFD-G35
Ver 1.3 2002. 09
5-17. Schematic Diagram – POWER Section –

*1

*2 *1
C901-904
0.022:US,CND,E,MX
0.1:AUS,AR,SP
*1
*1

* 2 F902
5A/125V:US,CND,E,MX
3.15A/250V:AUS,AR,SP

*1

33 33
CFD-G35
• IC Block Diagrams IC701 LC78646E-E
IC1 TA2149BN

PCKIST

CONT1
CONT2
CONT3

VDD5V

*WRQ
VVSS
VVDD

PD02
PD01

*RES
LDS
LDD

VSS

DRF

CL
CE
DO
FR

DI
GND1 1 24 FM RF OUT 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
FM RF
23 VCC1
FM RF IN 2
AM 22 AM RF IN APC PLL GATE GATE
AM LOW CUT 3 MIX VCEC 60 DATA

INTERPOLATION
SERIAL

ATTENUATION
DEEMPHASIS
MIX OUT 4 FM FM GENERAL- 59 DATACK
MIX OSC 21 FM OSC PCK COMMAND OUT

MUTE
PURPOSE DRF 58 LRSY
INTERFACE
AM PORTS
OSC 20 AM OSC 57 ASDFIN
EXTERNAL
VCC2 5 BUFF BUFF 1/1OR 56 ASDACK
19 OSC OUT AUDIO IN
LEVEL 1/16 55 ASLRCK
AM IF DET SLCO 1 SLICE
AF IF IN 6 ST 18 ST IND SLCIST 2 LEVEL
FM IF IF BUFF EFMIN 3 CONTROL
54 16MOUT
FM IF IN 7 1/8
SW 4 RAM
RF
RFVDD 5 ERROR 53 EFLG
GND2 8 AM
RFVSS 6 – CORRECTION 52 C2F
DET IF REQ 17 IF OUT
AF BUFF AUDIO CD
AGC 9 AGC + MIX EQ AGC C1-1, C2-2
16 DET OUT FIN1 7 51 XVSS
FM AF 50 FSX/16MIN
QUAD 10 DET 15 MPX IN
+ AUTO 8FS
–
ST/MO FIN2 8 – ADJUST DIGITAL
R OUT 11 + CLOCK 49 XIN
FM/AM LPF PH FILTER
+ GENERATOR
MUTE 48 XOUT
VCO 14 LPF2/MO-ST
L OUT 12 LEVEL SET BH 47 XVDD
DIVIDE
1BIT
DECODE 13 LPF1/BAND DAC
TIN1 –
9
TBAL
+

+ 46 RVDD
– –
IC2 LC72137M-TLM TIN2 10 + 45 RCHO
TBAL
+ 44 RVSS
LP-OUT

MO/ST

AM-IN
X OUT

FM-IN
LP-IN

VDD
X IN

VSS

LPF
PD

LPF + 43 LVSS
20 19 18 17 16 15 14 13 12 11
– 42 LCHO
VREF 11
FILTER 41 LVSS
–
+ FRAME SYNC DETECT,
POWER LPF PROTECT INSERT,
+
ON REFI 12 EFM DECODE
–
REFERENCE PHASE DETECTOR RESET
DIVIDER CHARGE PUMP
+
1/2 FE 13 RUPTURE SUBCODE
UNLOCK TEC 14 SW – DEFECT DECODE CRC
DETECTOR
TE 15
SWALLOW COUNTER MONI
1/16. 1/17 4 BITS RFMON 16
CONT

12 BIT PROGRAMBLE TRACK

DIVIDER JUMP
JITTER
JITTC 17
DETECT AUDIO
MONITOR
CLV, CAV OUT
OCB DATA SHIFT REGISTER UNIVERSAL SIGNAL
SW D/A CONTROL
I/F LATCH CONTROLER SELECTOR

SERVO
A/D
1 2 3 4 5 6 7 8 9 10 PROCESSOR
ADAVDD 18
RAM S/H
CE

DI

CL

DO

NUTE

MW/LW

BAND

ST-IND

BAND

IF-IN

ADAVSS 19

TDO 20
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40

FSEQ

TEST
DOUT
MONI2
MONI3

VDD
SLDO

SBCK/CONT6

DEFECT
GPDAC

(3.3V)VSS
MONI1

MONI4
MONI5
FDO
SPDO

V/*P
CONT4
CONT5

SBCK/FG
IC321 BD3870FS
BOUT2

BOUT1

OUT1

OUT2
BNF2

BNF1
TNF1

TNF2

VCC
CAP

SC
SI

24 23 22 21 20 19 18 17 16 15 14 13

Treble1 Treble2 Bass2 Bass1

Logic
Surround

fc=8kHz fc=8kHz fo=80Hz fo=80Hz

Vcc/2 Vcc/2

0dB-
-87dB Vcc/2
-
Vcc/2 Vcc/2

50k 50k 50k 50k 50k 50k

1 2 3 4 5 6 7 8 9 10 11 12
VIN1

VIN2

SEL2

SEL1

A1

A2

B1

B2

C1

C2

FILTER

GND

34 34
 CFD-G35

IC301 TA2068N

R. RAD
L. RAD

R. LIN
L. LIN

TAPE
L. LO

R. LO

LINE

MIC
VCC
REC
MIC
I/EX

IN
24 23 22 21 20 19 18 17 16 15 14 13

1k 1k
10k 10k
LOGIC

1k
6k 10k
15k 10k 6k 10k
7dB 7dB

RADIO
RADOI

MONITOR
MONITOR AMP
AMP LINE
LINE
MUTE

MUTE
ON

ON
–––––

–––––
TAPE

TAPE
10k 10k
BUF AMP BUF AMP
B1 B2
TAPE TAPE
10k 10k
BUF AMP BUF AMP

A1 A2
10k MIC
10k MUTE
10k 10k AMP1

ON
ALC1 ALC2

NAB NAB 1k
26dB 26dB
AMP1 AMP2
REC REC
DET
AMP1 AMP2
10k

2.1
REF AMP

1 2 3 4 5 6 7 8 9 10 11 12
AGC

L. PO

L. NF

L. RO

L. IN

REF

GND

R. IN

R. RO

R. NF

R. PO

MIC
NF
IC702 BA5826FP-E2
(SLIN)

VREF

OPIN
(FIN)
SLIN
GND

SL –

VCC

VCC
SL+

FIN

F–

F+

NC

28 27 26 25 24 23 22 21 20 19 18 17 16 15
DRIVE DRIVE
BUFFER BUFFER
VCC VCC

LEVEL LEVEL
SHIFT SHIFT

– –
+ +

+ +
– –
REGULATOR VOLTAGE DETECT, DRIVER
BIAS VOLTAGE DETECT, MUTING
+
–

THERMAL SHUT DOWN

LEVEL LEVEL
SHIFT SHIFT
–
+
DRIVE DRIVE
BUFFER BUFFER
1 2 3 4 5 6 7 8 9 10 11 12 13 14
(TIN)
SP –

SP +

SPIN
RST
REG-B

REGO

MUTE

GND

TIN

T–

T+

GND
OPOUT

35
CFD-G35

5-18. IC Pin Function Description

• IC801 µPD789478GC-8BT System Control (MAIN Board)
Pin No. Pin Name I/O Description
1, 2 NC — Not used (open)
3 VLC2 I LCD bias power supply
4 VLC1 I LCD bias power supply
5 VLC0 I LCD bias power supply
6 to 9 COM0 to COM3 O LCD common signal output
10 to 27 SEG0 to SEG17 O LCD segment signal output
28, 29 NC — Not used (open)
30 WOOFER ON/OFF O Woofer on/off control signal output
31 WOOFER 1/2 O Woofer 1/2 signal output (not used)
32 ISS1 O ISS-1 signal output (not used)
33 ISS2 O ISS-2 signal output (not used)
34 A-MUTE O Audio muting signal output
35 SCL O Clock output to the EEPROM
36 SDA I/O Data input/output with the EEPROM
37 INIT O Initialization setting signal output
38 AVDD — Power supply (A/D converter)
39 REC I REC signal input from the REC/PB switch (S301) “H”: record mode
40 C-DOOR I Detection signal input from the CD OPEN switch (S701) “L”: CD door close
41 SIMUKE I Destination setting signal input
42 MODE I Model setting signal input
43 to 45 KEY-1 to KEY-3 I Key signal input from the function keys
46 C-FSEQ I CD FSEQ synchronizing signal detection signal input from the IC701
47 AVSS — Ground (A/D converter)
48 RMC I Data input from the remote control receiver
49 REG CHK I Power supply voltage monitoring signal input
50 WP I/O WAKE UP reading signal output (interrupt signal in input mode)
51 TC-PLAY I TAPE PLAYsignal input from the TC PLAY switch (S321)
52 WRQ I CD WRQ signal input from the IC701
53 C-DO I CD DSP data input from the IC701
54 C-DI O CD DSP data output to the IC701
55 C-CLK O CD clock output to the IC701
56 C-CE O CD chip enable signal output to the IC701
57 R-MUTE O Radio muting signal output “L”: active
58 C-DRF I CD DRF signal input from the IC701
59 C-RES O CD system reset signal output to the IC701
60 R-COUNT I Radio IF count signal input from the IC2
61 R-CLK O Radio clock signal output to the IC2
62 R-DATA O Radio data output to the IC2
63 R-CE O Radio chip enable signal output to the IC2
64 V-CLOCK O Clock signal output to the sound processor (IC321)
65 V-DATA O Data output to the sound processor (IC321)
66 P-CON O Power control signal output
67 TAPE O TAPE function signal output to the IC301
68 VL O VL control signal output “L”: active
69 NC I Not used (connected to ground)
70 XT1 I Sub system clock oscillator input (32.768kHz)
71 XT2 O Sub system clock oscillator output (32.768kHz)
72 VDD — Power supply
73 VSS — Ground
74 X1 I Main system clock oscillator input (4.19MHz)

36
 CFD-G35

Pin No. Pin Name I/O Description

75 X2 O Main system clock oscillator output (4.19MHz)
76 RST I System reset signal input
77 CD O CD function signal output “L”: active
78 LED CONT O LED control signal output (not used)
79 W-LED1 O Woofer1 LED control signal output
80 W-LED2 O Woofer2 LED control signal output (not used)

37
CFD-G35
Ver 1.3 2002. 09 SECTION 6
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may • Color Indication of Appearance Parts Example: CND : Canadian model.
have some differences from the original one. KNOB, BALANCE (WHITE) . . . . (RED) E92 : Chilean and Peruvian model.
• Items marked “*” are not stocked since they MX : Mexican model.
  SP : Singapore model.
are seldom required for routine service. Some Parts color Cabinets color
delay should be anticipated when ordering these • Accessories are given in the last of this parts list. The components identified by mark 0 or
items. • Abbreviation dotted line with mark 0 are critical for safety.
• The mechanical parts with no reference number AR : Argentina model. Replace only with part number specified.
in the exploded views are not supplied. AUS : Australian model. Les composants identifiés par une marque
0 sont critiques pour la sécurité.
6-1. Cabinet (Front) Section #3 23 Ne les remplacer que par une pièce portant
le numéro spécifié.
#3
23 13
12
25
LCD891 #1
14 #2
11 15
10 17
16

18
ba
9 8
23 7 cabinet (rear) sectioin
#3 #3
SP391
5 23
6 #3

4 #3
19
23

3 24 20
#4
a 23 23
SP393
b
21
#3
2
1 24

22
SP392

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 3-238-215-01 COVER (WOOFER.943) (BLACK) 15 3-238-242-11 BUTTON (VOL) (BLACK)
1 X-3381-844-1 COVER (WOOFER) ASSY (SILVER) 15 3-238-242-21 BUTTON (VOL) (SILVER)
2 3-238-224-01 COVER (WOOFER.COM) (BLACK) 16 3-238-247-01 PLATE (PDW), LIGHT GUIDE
2 3-238-224-11 COVER (WOOFER.COM) (SILVER) 17 1-823-744-11 CABLE, FLEXIBLE FLAT (4 CORE)
3 X-3381-822-1 CABINET (FRONT) SUB ASSY (BLACK) (US) 18 3-238-936-01 SHEET (LCD WINDOW), ADHESIVE
3 X-3381-838-1 CABINET (FRONT) SUB ASSY (BLACK) 19 3-238-250-01 LID, BATTERY CASE (BLACK)
(CND,E92,MX,AR,SP) 19 3-238-250-11 LID, BATTERY CASE (SILVER)
3 X-3381-841-1 CABINET (FRONT) SUB ASSY (SILVER) (AUS,SP) 20 3-238-244-01 BUTTON (CD) (BLACK)
* 4 1-684-458-11 CONTROL (POWER) BOARD 20 3-238-244-11 BUTTON (CD) (SILVER)
5 3-238-243-11 BUTTON (POWER) (BLACK) * 21 1-684-460-11 CONTROL (CD) BOARD
5 3-238-243-21 BUTTON (POWER) (SILVER)
22 3-040-916-01 CUSHION (FOOT) FRONT
6 3-238-235-01 CHASSIS (H/J) 23 4-951-620-11 SCREW (2.6X10), +BVTP
* 7 1-684-457-11 HEADPHONE BOARD 24 4-951-620-01 SCREW (2.6X8), +BVTP
* 8 1-684-459-11 CONTROL (VOL) BOARD 25 3-238-938-01 HOLDER, LCD
9 1-823-740-11 CABLE, FLEXIBLE FLAT (26 CORE) LCD891 1-804-640-11 DISPLAY PANEL, LIQUID CRYSTAL
10 3-238-226-01 WINDOW (LCD) (BLACK)
SP391 1-825-029-11 SPEAKER (10cm) (BLACK)
10 3-238-226-11 WINDOW (LCD) (SILVER) SP391 1-825-159-11 SPEAKER (10cm) (SILVER)
11 X-3381-823-1 PANEL (FRONT) ASSY (BLACK) SP392 1-825-029-11 SPEAKER (10cm) (BLACK)
11 X-3381-842-1 PANEL (FRONT) ASSY (SILVER) SP392 1-825-159-11 SPEAKER (10cm) (SILVER)
* 12 1-684-454-11 LCD BOARD SP393 1-825-030-11 SPEAKER (8cm) (WOOFER)
13 3-238-222-11 PANEL (UPPER) (BLACK)
#1 7-685-651-79 SCREW +BVTP 3X20 TYPE2 N-S
13 3-238-222-21 PANEL (UPPER) (SILVER) #2 7-685-649-79 SCREW +BVTP 3X14 TYPE2 N-S
14 3-238-245-01 BUTTON (PDW) (BLACK) #3 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
14 3-238-245-11 BUTTON (PDW) (SILVER) #4 7-685-783-09 SCREW +PTT 2X6 (S)
38
 CFD-G35
Ver 1.3 2002. 09

6-2. Cabinet (Rear) Section

60

59
58
57

#3 #5 63
#3 #3
#3
#3 #3
ANT1
b cabinet (upper)
T901 section
55 56
not a
supplied
74 61
F902
62
#6

54
#3

#3
53
52 64
66 71
65
not 71
supplied
#3
#3 #3 b
a

70 72
51
68 67
not
supplied #3
#3
72
#3 69
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
51 3-238-229-01 DUCT (LOWER) (BLACK) 63 3-238-249-11 HANDLE (SILVER)
51 3-238-229-11 DUCT (LOWER) (SILVER) * 64 1-684-462-11 BATT COM BOARD
52 3-238-228-01 DUCT (UPPER) (BLACK) 65 3-238-136-01 TERMINAL (+,–), BATTERY
52 3-238-228-11 DUCT (UPPER) (SILVER) 66 3-238-214-01 TERMINAL (+,–), BATTERY
53 4-951-620-01 SCREW (2.6X8), +BVTP * 67 1-684-453-11 BATT BOARD

54 3-238-230-01 CHASSIS (TRANS) * 68 A-3323-779-A TUNER BOARD ,COMPLETE (US,CND,E92,MX)

* 55 1-684-451-11 POWER BOARD * 68 A-3323-815-A TUNER BOARD ,COMPLETE (AUS,AR,SP)
56 3-238-934-01 SPRING (CASSETTE) 69 3-238-231-01 CHASSIS (TU)
57 X-3381-821-1 HOLDER ASSY, CASSETTE (BLACK) 70 3-238-134-01 TERMINAL, ANTENNA
57 X-3381-840-1 HOLDER ASSY, CASSETTE (SILVER) 71 3-238-135-01 TERMINAL (–), BATTERY

58 1-452-899-11 MAGNET 72 4-960-167-01 SCREW (3X8) (DIA. 10), +WH

59 3-019-395-01 PLATE, CHUCKING * 74 1-684-452-11 TRANS BOARD
60 3-238-219-11 LID, CD (BLACK) ANT1 1-501-883-21 ANTENNA, TELESCOPIC
60 3-238-219-31 LID, CD (SILVER) 0 F902 1-532-465-11 FUSE, TIME LAG 3.15A/250V(AUS,AR,SP)
61 3-238-935-01 SPRING (CD) 0 F902 1-576-109-11 FUSE 5A/125V(US,CND,E92,MX)

62 3-238-217-31 CABINET (REAR) (BLACK) (US) 0 T901 1-437-644-11 TRANSFORMER, POWER(US,CND,E92,MX)

62 3-238-217-41 CABINET (REAR) (BLACK) (CND,E92,MX) 0 T901 1-437-645-11 TRANSFORMER, POWER(AUS,AR,SP)
62 3-238-217-51 CABINET (REAR) (BLACK) (AR,SP) #3 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
62 3-238-217-71 CABINET (REAR) (SILVER) (AUS,SP) #5 7-685-533-19 SCREW +BTP 2.6X6 TYPE2 N-S
63 3-238-249-01 HANDLE (BLACK) #6 7-682-548-04 SCREW +B 3X8
The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié. 39
CFD-G35
Ver 1.3 2002. 09

6-3. Cabinet (Upper) Section

S801 114

112
#3

115
mechanism
deck section-1
(MF-V5-117)

127 129
107
106 108 116 117 CD mechanism
109 #3 section
110 (KSM-213RDP)
130
105 111
131 #3
not 124
128 supplied S321
#6 119
#3 132 125
#6 126
128 #3 #7 118
121
113
102 #6 128
122 120
#3 not
not
#3 not supplied supplied
supplied #3
103
132
101 #3
#3 132
#3 123
#3 #3 113 #3

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* 101 A-3178-395-A L-R/REG BOARD, COMPLETE 118 3-931-379-21 RUBBER, VIBRATION PROOF
102 3-238-232-01 CHASSIS (HS.L) 119 3-931-379-31 RUBBER, VIBRATION PROOF
103 1-757-778-11 CABLE, FLEXIBLE FLAT (11 CORE) * 120 A-3178-396-A PDW BOARD,COMPLETE (US,CND,E92,MX)
105 3-031-560-01 SHAFT (MD) * 120 A-3178-479-A PDW BOARD,COMPLETE (AUS,AR,SP)
106 3-238-236-01 BUTTON (REC) (BLACK) 121 3-238-233-01 CHASSIS (HS.R)

106 3-238-236-11 BUTTON (REC) (SILVER) * 122 A-3178-397-A MAIN BOARD,COMPLETE (US,E92,MX)
107 3-238-237-01 BUTTON (PLAY) (BLACK) * 122 A-3178-469-A MAIN BOARD,COMPLETE (CND)
107 3-238-237-11 BUTTON (PLAY) (SILVER) * 122 A-3178-471-A MAIN BOARD,COMPLETE (AR)
108 3-238-238-01 BUTTON (REW) (BLACK) * 122 A-3178-472-A MAIN BOARD,COMPLETE (SP)
108 3-238-238-11 BUTTON (REW) (SILVER) 123 1-823-742-11 WIRE (FLAT TYPE) (14 CORE)

109 3-238-239-01 BUTTON (FF) (BLACK) 124 1-757-689-11 CABLE, FLEXIBLE FLAT (16 CORE)
109 3-238-239-11 BUTTON (FF) (SILVER) * 125 A-3178-122-A CD BOARD, COMPLETE
110 3-238-240-01 BUTTON (STOP/EJECT) (BLACK) 126 A-3178-403-A TC BOARD, COMPLETE
110 3-238-240-11 BUTTON (STOP/EJECT) (SILVER) 127 3-222-727-01 LEVER (REC)
111 3-238-241-01 BUTTON (PAUSE) (BLACK) 128 3-921-725-01 SCREW (2.6X10), +PWH

111 3-238-241-11 BUTTON (PAUSE) (SILVER) 129 3-047-468-11 DAMPER

112 3-047-468-01 DAMPER 130 4-951-620-01 SCREW (2.6X8), +BVTP
113 4-960-167-01 SCREW (3X8) (DIA. 10), +WH 131 3-222-726-01 CHASSIS (TC)
114 3-232-770-01 STOPPER (CD) 132 3-703-150-11 CLAMP
115 3-238-218-21 CABINET (UPPER) (BLACK) (US,AR) S321 1-771-686-11 SWITCH, LEAF (PLAY SW)

115 3-238-218-31 CABINET (UPPER) (BLACK) (CND,E92,MX,SP) S801 1-692-960-11 SWITCH, PUSH (1 KEY) (ZPUSH OPEN/CLOSE)
115 3-238-218-41 CABINET (UPPER) (SILVER) (AUS,SP) #3 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
116 3-238-234-01 CHASSIS (CD) #6 7-682-548-04 SCREW +B 3X8
117 3-923-736-01 COVER, CD #7 7-685-853-04 SCREW +BVTT 2X6 (S)

40
 CFD-G35

6-4. Mechanism Deck Section- 1 (MF-V5-117)

HRP301

159

HE301 170

158 160 161

162
169
168
163 164
157

155 156
167 165

154

153

166

151
mechanism deck section-2
(MF-V5-117)
152

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
151 3-933-010-01 SPRING (S/P), TORSION * 162 3-008-587-01 SLIDER (STOP)
152 3-933-025-01 SPRING (P), TORSION * 163 3-008-591-01 SLIDER (PAUSE)
153 3-040-857-01 LEVER (P) 164 3-933-004-01 CLAW, REEL
154 3-933-024-01 ROLLER, PINCH * 165 3-933-021-01 SLIDER (FRP)
155 3-933-019-01 SPRING (F/R), TORSION * 166 3-933-006-01 SLIDER (EJECT)

156 3-933-028-01 SPRING (FWD), TORSION 167 3-934-833-01 SPRING (FRP)

157 3-933-016-01 GEAR (S REEL) 168 3-022-794-02 SPRING (BT)
158 3-008-590-01 SLIDER (REC) 169 3-933-007-01 PLATE, LOCK
159 3-008-592-23 BASE (H), HEAD * 170 3-012-114-01 LEVER (FR)
* 160 3-008-588-01 SLIDER (REW) HE301 1-543-876-11 HEAD (ERASE)

* 161 3-008-589-13 SLIDER (FF) HRP301 1-500-691-11 HEAD,MAGNETIC(RECORD/PLAYBACK)

41
CFD-G35

6-5. Mechanism Deck Section- 2 (MF-V5-117)

207

206 219

209
208

204 205 210

216
203

S322 211

218
212
M321

213

217

214
#10 215
202 201

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
201 3-933-029-01 LEVER, ERASING PREVENTION 213 3-932-993-01 CHASSIS, OUTSERT
202 3-933-182-01 SPRING, CASSETTE 214 3-343-358-01 RING, RETAINING
203 3-932-995-01 GEAR (MID) 215 3-933-005-01 SPRING (CAM), COMPRESSION
204 X-3371-667-1 CLUTCH ASSY 216 3-939-383-02 SPRING, COMPRESSION
205 3-932-997-01 GEAR (CAM) 217 3-937-760-01 SPRING (GROUND), COMPRESSION

* 206 3-932-999-01 SLIDER (SW) 218 3-934-336-01 BEARING

207 3-932-998-01 SPRING (GROUND), TORSION 219 3-009-650-02 SPRING (K), COMPRESSION
208 3-009-648-01 LEVER (S.OFF) M321 A-3320-446-A MOTOR ASSY (CAPSTAN/REEL)
209 3-936-438-01 LEVER (K) S322 1-762-679-11 SWITCH, LEAF (MOTOR SW)
210 X-3373-572-1 REEL ASSY (N), T #10 7-621-770-87 SCREW +B 2.6X5

211 3-933-020-11 BELT

212 X-3377-877-3 FLYWHEEL ASSY

42
 CFD-G35
Ver 1.3 2002. 09

6-6. CD Mechanism Section (KSM-213RDP)

251

252

254
253

255 256

260
258
(including M702)

259

M702

M701

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
0 251 8-820-161-02 OPTICAL PICK-UP KSS-213R 256 3-713-786-51 SCREW (M2 x 3)
* 252 2-169-065-01 GEAR (A) 258 X-2162-707-1 CHASSIS ASSY, (RDP) (RP) MOTOR (SPINDLE)
* 253 2-169-385-01 SPRING, SLED 259 2-626-908-01 SHAFT, SLED
* 254 2-647-408-02 GEAR (B) * 260 2-169-384-01 SHAFT (S), GEAR
255 2-169-388-01 TAPPING (M2), +PWB M701 X-2162-712-1 GEAR ASSY (R) (RP), MOTOR (SLED)

The components identified by Les composants identifiés par

mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.

43
CFD-G35
Ver 1.3 2002. 09 SECTION 7
BATT BATT COM CD ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the • Items marked “*” are not stocked since they CND : Canadian model.
parts list may be different from the parts are seldom required for routine service. Some E92 : Chilean and Peruvian model.
specified in the diagrams or the components delay should be anticipated when ordering these MX : Mexican model.
used on the set. items. SP : Singapore model.
• -XX, -X mean standardized parts, so they may • RESISTORS
When indicating parts by reference number,
have some difference from the original one. All resistors are in ohms. please include the board name.
• SEMICONDUCTORS METAL: metal-film resistor
In each case, u: µ, for example: METAL OXIDE: Metal Oxide-film resistor The components identified by mark 0 or
uA...: µA... , uPA... , µPA... , F: nonflammable dotted line with mark 0 are critical for safety.
uPB... , µPB... , uPC... , µPC... , • COILS Replace only with part number specified.
uPD..., µPD... uH: µH Les composants identifiés par une marque
• CAPACITORS: • Abbreviation 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
uF: µF AR : Argentina model.
le numéro spécifié.
AUS : Australian model.
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* 1-684-453-11 BATT BOARD C739 1-164-156-11 CERAMIC CHIP 0.1uF 25V
*********** C740 1-126-935-11 ELECT 470uF 20.00% 10V
C741 1-164-156-11 CERAMIC CHIP 0.1uF 25V
3-238-135-01 TERMINAL (-), BATTERY C742 1-164-156-11 CERAMIC CHIP 0.1uF 25V
C743 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< CABLE HOLDER >
C744 1-164-156-11 CERAMIC CHIP 0.1uF 25V
* KH941 1-565-385-11 HOLDER, CABLE 4P C745 1-164-156-11 CERAMIC CHIP 0.1uF 25V
************************************************************** C746 1-104-665-11 ELECT 100uF 20.00% 10V
C747 1-104-665-11 ELECT 100uF 20.00% 10V
* 1-684-462-11 BATT COM BOARD C750 1-104-665-11 ELECT 100uF 20.00% 10V
***************
C751 1-164-156-11 CERAMIC CHIP 0.1uF 25V
3-238-135-01 TERMINAL (-), BATTERY C754 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
************************************************************** C755 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

* A-3178-122-A CD BOARD, COMPLETE < CONNECTOR >

*******************
CNP701 1-770-168-11 CONNECTOR, FFC/FPC 16P
< CAPACITOR > * CNP702 1-784-736-11 CONNECTOR, FFC 14P

C701 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < FERRITE BEAD >
C702 1-126-947-11 ELECT 47uF 20.00% 10V
C703 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V FB701 1-469-701-21 INDUCTOR 0UH
C704 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C705 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V < IC >

C706 1-126-960-11 ELECT 1uF 20.00% 50V IC701 6-701-796-01 IC LC78646E-E

C707 1-115-156-11 CERAMIC CHIP 1uF 10V IC702 6-701-787-11 IC BA5826FP-E2
C708 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C709 1-164-156-11 CERAMIC CHIP 0.1uF 25V < JUMPER RESISTOR >
C711 1-162-974-11 CERAMIC CHIP 0.01uF 50V
JC701 1-216-864-11 METAL CHIP 0 5% 1/16W
C716 1-162-974-11 CERAMIC CHIP 0.01uF 50V JC702 1-216-864-11 METAL CHIP 0 5% 1/16W
C717 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V JC703 1-216-864-11 METAL CHIP 0 5% 1/16W
C720 1-162-919-11 CERAMIC CHIP 22PF 5% 50V JC704 1-216-821-11 METAL CHIP 1K 5% 1/16W
C721 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C722 1-162-919-11 CERAMIC CHIP 22PF 5% 50V < COIL >

C723 1-162-974-11 CERAMIC CHIP 0.01uF 50V L706 1-414-445-11 FERRITE 0uH
C724 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C725 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < TRANSISTOR >
C726 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C727 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V Q701 8-729-054-57 TRANSISTOR KTN2907AS-RTK

C728 1-165-176-11 CERAMIC CHIP 0.047uF 10.00% 16V < RESISTOR >
C729 1-125-837-91 CERAMIC CHIP 1uF 10% 6.3V
C730 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V R701 1-216-841-11 METAL CHIP 47K 5% 1/16W
C731 1-165-176-11 CERAMIC CHIP 0.047uF 10.00% 16V R702 1-216-835-11 METAL CHIP 15K 5% 1/16W
C732 1-104-665-11 ELECT 100uF 20.00% 10V R703 1-216-835-11 METAL CHIP 15K 5% 1/16W
R704 1-216-835-11 METAL CHIP 15K 5% 1/16W
C733 1-104-665-11 ELECT 100uF 20.00% 10V R705 1-216-835-11 METAL CHIP 15K 5% 1/16W
C734 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C735 1-126-916-11 ELECT 1000uF 20.00% 6.3V
C736 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C738 1-164-156-11 CERAMIC CHIP 0.1uF 25V

44
 CFD-G35
Ver 1.1 2002. 05
CD CONTROL (CD) CONTROL (POWER) CONTROL (VOL)
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R706 1-216-841-11 METAL CHIP 47K 5% 1/16W * 1-684-458-11 CONTROL (POWER) BOARD
R707 1-216-797-11 METAL CHIP 10 5% 1/16W ***********************
R708 1-216-833-11 METAL CHIP 10K 5% 1/16W
R709 1-216-837-11 METAL CHIP 22K 5% 1/16W < CABLE HOLDER >
R710 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
* KH404 1-565-384-11 HOLDER, CABLE 3P
R711 1-216-815-11 METAL CHIP 330 5% 1/16W
R712 1-216-809-11 METAL CHIP 100 5% 1/16W < RESISTOR >
R714 1-216-811-11 METAL CHIP 150 5% 1/16W
R715 1-216-811-11 METAL CHIP 150 5% 1/16W R401 1-216-817-11 METAL CHIP 470 5% 1/16W
R716 1-216-821-11 METAL CHIP 1K 5% 1/16W R402 1-216-813-11 METAL CHIP 220 5% 1/16W
R403 1-216-821-11 METAL CHIP 1K 5% 1/16W
R717 1-216-821-11 METAL CHIP 1K 5% 1/16W
R718 1-216-821-11 METAL CHIP 1K 5% 1/16W < SWITCH >
R719 1-216-809-11 METAL CHIP 100 5% 1/16W
R720 1-216-809-11 METAL CHIP 100 5% 1/16W S401 1-771-349-21 SWITCH, TACT (POWER)
R721 1-216-821-11 METAL CHIP 1K 5% 1/16W S402 1-771-349-21 SWITCH, TACT (SLEEP)
**************************************************************
R722 1-216-809-11 METAL CHIP 100 5% 1/16W
R723 1-216-809-11 METAL CHIP 100 5% 1/16W * 1-684-459-11 CONTROL (VOL) BOARD
R724 1-216-841-11 METAL CHIP 47K 5% 1/16W ********************
R725 1-216-819-11 METAL CHIP 680 5% 1/16W
R726 1-216-819-11 METAL CHIP 680 5% 1/16W < CONNECTOR >

R727 1-216-825-11 METAL CHIP 2.2K 5% 1/16W CNP401 1-784-726-11 CONNECTOR, FFC 4P
R728 1-216-833-11 METAL CHIP 10K 5% 1/16W
R729 1-216-813-11 METAL CHIP 220 5% 1/16W < DIODE >
R730 1-216-821-11 METAL CHIP 1K 5% 1/16W
R731 1-216-825-11 METAL CHIP 2.2K 5% 1/16W D401 8-719-085-33 DIODE SLI-343URCT32WST
(POWER DRIVE WOOFER)
R732 1-216-841-11 METAL CHIP 47K 5% 1/16W (only for the cabinet color is black)
R741 1-218-867-11 RES-CHIP 6.8K 5% 1/10W D401 6-500-284-01 DIODE DB3804X(POWER DRIVE WOOFER)
R743 1-218-867-11 RES-CHIP 6.8K 5% 1/10W (only for the cabinet color is silver)
R744 1-216-845-11 METAL CHIP 100K 5% 1/16W
< CABLE HOLDER >
< SWITCH >
* KH402 1-565-386-11 HOLDER, CABLE 5P
S701 1-571-936-11 SWITCH, LEAF (LIMITIN)
< RESISTOR >
< VIBRATOR >
R411 1-216-817-11 METAL CHIP 470 5% 1/16W
X701 1-781-801-21 VIBRATOR, CERAMIC 16.93MHz R412 1-216-813-11 METAL CHIP 220 5% 1/16W
************************************************************** R413 1-216-821-11 METAL CHIP 1K 5% 1/16W
R414 1-216-821-11 METAL CHIP 1K 5% 1/16W
* 1-684-460-11 CONTROL (CD) BOARD R415 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
*******************
R416 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
< CABLE HOLDER > R417 1-216-821-11 METAL CHIP 1K 5% 1/16W
R418 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
* KH403 1-573-287-11 HOLDER, CABLE 2P R419 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R420 1-216-837-11 METAL CHIP 22K 5% 1/16W
< RESISTOR >
< SWITCH >
R404 1-216-821-11 METAL CHIP 1K 5% 1/16W
R405 1-216-825-11 METAL CHIP 2.2K 5% 1/16W S409 1-771-349-21 SWITCH, TACT (MODE)
R406 1-216-825-11 METAL CHIP 2.2K 5% 1/16W S410 1-771-349-21 SWITCH, TACT (TUNE+)
R407 1-216-821-11 METAL CHIP 1K 5% 1/16W S411 1-771-349-21 SWITCH, TACT (TUNE-)
R408 1-216-829-11 METAL CHIP 4.7K 5% 1/16W S412 1-771-349-21 SWITCH, TACT (SOUND)
S413 1-771-349-21 SWITCH, TACT (DISPLAY/ENTER/MEMORY)
R409 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R410 1-216-837-11 METAL CHIP 22K 5% 1/16W S414 1-771-349-21 SWITCH, TACT (VOLUME-)
S415 1-771-349-21 SWITCH, TACT (VOLUME+)
< SWITCH > S416 1-771-349-21 SWITCH, TACT (POWER DRIVE WOOFER)
**************************************************************
S404 1-771-349-21 SWITCH, TACT (u)
S405 1-771-349-21 SWITCH, TACT (x)
S406 1-771-349-21 SWITCH, TACT (AUTO PRESET/BAND)
S407 1-771-349-21 SWITCH, TACT (PRESET+ >)
S408 1-771-349-21 SWITCH, TACT (PRESET– .)
**************************************************************

45
CFD-G35
Ver 1.3 2002. 09
HEADPHONE L-R/REG LCD MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* 1-684-457-11 HEADPHONE BOARD < RESISTOR >
*****************
R171 1-216-841-11 METAL CHIP 47K 5% 1/16W
< CONNECTOR > R172 1-216-837-11 METAL CHIP 22K 5% 1/16W
R173 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
* CNP391 1-785-657-21 PIN, CONNECTOR (PC BOARD) 5P R174 1-216-833-11 METAL CHIP 10K 5% 1/16W
* CNP392 1-785-656-21 PIN, CONNECTOR (PC BOARD) 4P R175 1-216-813-11 METAL CHIP 220 5% 1/16W
* CNP393 1-785-656-11 PIN, CONNECTOR (PC BOARD) 4P
* CNP394 1-785-656-11 PIN, CONNECTOR (PC BOARD) 4P R176 1-216-805-11 METAL CHIP 47 5% 1/16W
R177 1-249-389-11 CARBON 4.7 5% 1/4W F
< JACK > R271 1-216-841-11 METAL CHIP 47K 5% 1/16W
R272 1-216-837-11 METAL CHIP 22K 5% 1/16W
J391 1-794-016-11 JACK (i) R273 1-216-825-11 METAL CHIP 2.2K 5% 1/16W

< RESISTOR > R274 1-216-833-11 METAL CHIP 10K 5% 1/16W

R275 1-216-813-11 METAL CHIP 220 5% 1/16W
R191 1-247-807-31 CARBON 100 5% 1/4W R276 1-216-805-11 METAL CHIP 47 5% 1/16W
R192 1-216-821-11 METAL CHIP 1K 5% 1/16W R277 1-249-389-11 CARBON 4.7 5% 1/4W F
R291 1-247-807-31 CARBON 100 5% 1/4W R371 1-216-833-11 METAL CHIP 10K 5% 1/16W
R292 1-216-821-11 METAL CHIP 1K 5% 1/16W **************************************************************
**************************************************************
* 1-684-454-11 LCD BOARD
* A-3178-395-A L-R/REG BOARD, COMPLETE **********
************************
3-238-938-01 HOLDER, LCD
3-238-232-01 CHASSIS (HS.L)
3-703-150-11 CLAMP < CAPACITOR >
4-960-167-01 SCREW (3X8) (DIA. 10), +WH
7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S C891 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V

< CAPACITOR > < CONNECTOR >

C171 1-126-947-11 ELECT 47uF 20.00% 10V * CNP891 1-784-748-11 CONNECTOR, FFC 26P
C172 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C173 1-126-947-11 ELECT 47uF 20.00% 10V < DIODE >
C174 1-126-926-11 ELECT 1000uF 20.00% 10V
C175 1-136-165-00 FILM 0.1uF 5.00% 50V D893 8-719-059-97 DIODE L-34HD (OPR/BATT)

C271 1-126-947-11 ELECT 47uF 20.00% 10V < IC >

C272 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C273 1-126-947-11 ELECT 47uF 20.00% 10V IC891 8-749-014-88 IC SPS-440-E (g)
C274 1-126-926-11 ELECT 1000uF 20.00% 10V
C275 1-136-165-00 FILM 0.1uF 5.00% 50V < LIQUID CRYSTAL DISPLAY >

C371 1-104-665-11 ELECT 100uF 20.00% 10V LCD891 1-804-640-11 DISPLAY PANEL, LIQUID CRYSTAL
C972 1-164-156-11 CERAMIC CHIP 0.1uF 25V
< RESISTOR >
< CONNECTOR >
R891 1-216-841-11 METAL CHIP 47K 5% 1/16W
* CNP371 1-785-655-21 PIN, CONNECTOR (PC BOARD) 3P R892 1-216-813-11 METAL CHIP 220 5% 1/16W
* CNP372 1-785-655-11 PIN, CONNECTOR (PC BOARD) 3P R893 1-216-817-11 METAL CHIP 470 5% 1/16W
* CNP373 1-785-657-11 PIN, CONNECTOR (PC BOARD) 5P R894 1-216-813-11 METAL CHIP 220 5% 1/16W
R895 1-216-817-11 METAL CHIP 470 5% 1/16W
< IC > **************************************************************

IC371 8-759-426-51 IC BA5417 * A-3178-397-A MAIN BOARD, COMPLETE (US,E92,MX)

*********************
< CABLE HOLDER > * A-3178-469-A MAIN BOARD, COMPLETE (CND)
*********************
* KH374 1-565-385-11 HOLDER, CABLE 4P * A-3178-471-A MAIN BOARD, COMPLETE (AR)
*********************
< TRANSISTOR > * A-3178-472-A MAIN BOARD, COMPLETE (SP)
*********************
Q171 8-729-281-53 TRANSISTOR 2SC1815GR-TPE2 * A-3178-473-A MAIN BOARD, COMPLETE (AUS)
Q271 8-729-281-53 TRANSISTOR 2SC1815GR-TPE2 *********************
Q972 8-729-037-08 TRANSISTOR KTD2058Y < CAPACITOR >

C123 1-126-961-11 ELECT 2.2uF 20.00% 50V

C124 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C126 1-126-961-11 ELECT 2.2uF 20.00% 50V

46
 CFD-G35
Ver 1.3 2002. 09
MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C127 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C841 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C129 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V C846 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V
C130 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V C953 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C131 1-126-960-11 ELECT 1uF 20.00% 50V C955 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C132 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C957 1-126-934-11 ELECT 220uF 20.00% 10V

C223 1-126-961-11 ELECT 2.2uF 20.00% 50V C958 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C224 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V C959 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C226 1-126-961-11 ELECT 2.2uF 20.00% 50V C960 1-126-934-11 ELECT 220uF 20.00% 10V
C227 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V C961 1-126-934-11 ELECT 220uF 20.00% 10V
C229 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V
< CONNECTOR >
C230 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V
C231 1-126-960-11 ELECT 1uF 20.00% 50V * CNP302 1-785-658-11 PIN, CONNECTOR (PC BOARD) 6P
C232 1-162-927-11 CERAMIC CHIP 100PF 5% 50V * CNP801 1-784-787-11 CONNECTOR, FFC 26P
C321 1-162-962-11 CERAMIC CHIP 470PF 10% 50V * CNP802 1-784-736-11 CONNECTOR, FFC 14P
(EXCEPT AUS) CNP804 1-784-765-11 CONNECTOR, FFC 4P
C322 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V CNP805 1-784-733-11 CONNECTOR, FFC 11P

C323 1-126-959-11 ELECT 0.47uF 20.00% 50V < DIODE >

C324 1-126-947-11 ELECT 47uF 20.00% 10V
C325 1-104-665-11 ELECT 100uF 20.00% 10V D320 8-719-991-33 DIODE 1SS133T-77
C326 1-165-176-11 CERAMIC CHIP 0.047uF 10.00% 16V D323 8-719-991-33 DIODE 1SS133T-77
C327 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V D324 8-719-991-33 DIODE 1SS133T-77
D806 8-719-991-33 DIODE 1SS133T-77
C333 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D807 8-719-991-33 DIODE 1SS133T-77
C334 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C336 1-126-947-11 ELECT 47uF 20.00% 10V D808 8-719-109-89 DIODE MTZJ-T-77-5.6B
C337 1-126-960-11 ELECT 1uF 20.00% 50V D951 8-719-991-33 DIODE 1SS133T-77(CND,AUS,AR,SP)
C338 1-126-964-11 ELECT 10uF 20.00% 50V D952 8-719-991-33 DIODE 1SS133T-77(CND,AUS,AR,SP)
D953 8-719-991-33 DIODE 1SS133T-77(CND,AUS,AR,SP)
C339 1-104-665-11 ELECT 100uF 20.00% 10V D955 8-719-109-97 DIODE MTZJ-T-77-6.8B
C341 1-128-551-11 ELECT 22uF 20.00% 25V
C342 1-162-927-11 CERAMIC CHIP 100PF 5% 50V D956 8-719-109-72 DIODE MTZJ-T-77-3.9B
C347 1-126-768-11 ELECT 2200uF 20.00% 16V D957 8-719-991-33 DIODE 1SS133T-77(CND,AUS,AR,SP)
C348 1-126-768-11 ELECT 2200uF 20.00% 16V
< IC >
C349 1-126-934-11 ELECT 220uF 20.00% 16V
C350 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V IC321 6-701-824-11 IC BD3870FS-E2
C801 1-126-960-11 ELECT 1uF 20.00% 50V IC801 6-801-780-01 IC uPD789478GC-A03-8BT
C802 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V IC802 8-759-658-46 IC S-81233SGY-Z
C803 1-126-934-11 ELECT 220uF 20.00% 10V IC803 8-759-487-03 IC BR24C01AF-WE2
IC805 8-759-645-87 IC PST9128-T
C807 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C808 1-162-919-11 CERAMIC CHIP 22PF 5% 50V < JUMPER RESISTOR >
C810 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C812 1-162-919-11 CERAMIC CHIP 22PF 5% 50V JC136 1-216-864-11 METAL CHIP 0 5% 1/16W
C814 1-128-551-11 ELECT 22uF 20.00% 25V JC236 1-216-864-11 METAL CHIP 0 5% 1/16W
JC307 1-216-864-11 METAL CHIP 0 5% 1/16W
C816 1-126-934-11 ELECT 220uF 20.00% 10V JC801 1-216-864-11 METAL CHIP 0 5% 1/16W
C817 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V JC803 1-216-864-11 METAL CHIP 0 5% 1/16W
C818 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V
C824 1-162-927-11 CERAMIC CHIP 100PF 5% 50V JC804 1-216-864-11 METAL CHIP 0 5% 1/16W
C825 1-162-927-11 CERAMIC CHIP 100PF 5% 50V JC953 1-216-864-11 METAL CHIP 0 5% 1/16W

C826 1-162-927-11 CERAMIC CHIP 100PF 5% 50V < CABLE HOLDER >
C827 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C828 1-162-927-11 CERAMIC CHIP 100PF 5% 50V * KH301 1-565-386-11 HOLDER, CABLE 5P
C829 1-162-927-11 CERAMIC CHIP 100PF 5% 50V * KH303 1-565-385-11 HOLDER, CABLE 4P
C830 1-162-927-11 CERAMIC CHIP 100PF 5% 50V * KH304 1-565-384-11 HOLDER, CABLE 3P
* KH305 1-565-384-11 HOLDER, CABLE 3P
C831 1-162-927-11 CERAMIC CHIP 100PF 5% 50V * KH306 1-565-385-11 HOLDER, CABLE 4P
C832 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C833 1-162-927-11 CERAMIC CHIP 100PF 5% 50V * KH307 1-565-386-11 HOLDER, CABLE 5P
C834 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C835 1-162-927-11 CERAMIC CHIP 100PF 5% 50V < COIL >

C838 1-126-959-11 ELECT 0.47uF 20.00% 50V L802 1-410-521-11 INDUCTOR 100uH
C839 1-126-959-11 ELECT 0.47uF 20.00% 50V

47
CFD-G35
Ver 1.3 2002. 09
MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< TRANSISTOR > R813 1-216-821-11 METAL CHIP 1K 5% 1/16W
R814 1-216-821-11 METAL CHIP 1K 5% 1/16W
Q321 8-729-281-53 TRANSISTOR 2SC1815GR-TPE2 R815 1-216-809-11 METAL CHIP 100 5% 1/16W
Q322 8-729-281-53 TRANSISTOR 2SC1815GR-TPE2 R816 1-216-809-11 METAL CHIP 100 5% 1/16W
Q810 8-729-029-26 TRANSISTOR DTA114YSA-TP R817 1-216-809-11 METAL CHIP 100 5% 1/16W
Q951 8-729-036-61 TRANSISTOR KRC105M-AT(CND,AUS,AR,SP)
Q952 8-729-195-23 TRANSISTOR 2SA952TP-K1K2 R818 1-216-821-11 METAL CHIP 1K 5% 1/16W
R819 1-216-821-11 METAL CHIP 1K 5% 1/16W
Q953 8-729-029-92 TRANSISTOR DTC143ESA-TP R820 1-216-821-11 METAL CHIP 1K 5% 1/16W
Q954 8-729-281-53 TRANSISTOR 2SC1815GR-TPE2 R821 1-216-821-11 METAL CHIP 1K 5% 1/16W
Q955 8-729-029-26 TRANSISTOR DTA114YSA-TP R822 1-216-821-11 METAL CHIP 1K 5% 1/16W
Q956 8-729-011-92 TRANSISTOR 2SC2001TP-K1K2
R823 1-216-821-11 METAL CHIP 1K 5% 1/16W
< RESISTOR > R824 1-216-821-11 METAL CHIP 1K 5% 1/16W
R825 1-216-821-11 METAL CHIP 1K 5% 1/16W
R123 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R826 1-216-821-11 METAL CHIP 1K 5% 1/16W
R125 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R827 1-216-821-11 METAL CHIP 1K 5% 1/16W
R126 1-216-821-11 METAL CHIP 1K 5% 1/16W
R127 1-216-833-11 METAL CHIP 10K 5% 1/16W R828 1-216-841-11 METAL CHIP 47K 5% 1/16W
R134 1-216-853-11 METAL CHIP 470K 5% 1/16W R829 1-216-821-11 METAL CHIP 1K 5% 1/16W
R830 1-216-813-11 METAL CHIP 220 5% 1/16W
R223 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R831 1-216-864-11 METAL CHIP 0 5% 1/16W
R225 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R832 1-216-809-11 METAL CHIP 100 5% 1/16W
R226 1-216-821-11 METAL CHIP 1K 5% 1/16W
R227 1-216-833-11 METAL CHIP 10K 5% 1/16W R833 1-216-864-11 METAL CHIP 0 5% 1/16W
R234 1-216-853-11 METAL CHIP 470K 5% 1/16W R835 1-216-864-11 METAL CHIP 0 5% 1/16W
R836 1-216-841-11 METAL CHIP 47K 5% 1/16W
R325 1-216-821-11 METAL CHIP 1K 5% 1/16W R837 1-216-841-11 METAL CHIP 47K 5% 1/16W
R326 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R839 1-216-841-11 METAL CHIP 47K 5% 1/16W
R328 1-216-821-11 METAL CHIP 1K 5% 1/16W
R331 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R840 1-216-841-11 METAL CHIP 47K 5% 1/16W
R332 1-216-853-11 METAL CHIP 470K 5% 1/16W R859 1-216-864-11 METAL CHIP 0 5% 1/16W
R860 1-216-841-11 METAL CHIP 47K 5% 1/16W
R333 1-216-833-11 METAL CHIP 10K 5% 1/16W R864 1-216-817-11 METAL CHIP 470 5% 1/16W
R335 1-216-837-11 METAL CHIP 22K 5% 1/16W R865 1-216-821-11 METAL CHIP 1K 5% 1/16W
R336 1-216-833-11 METAL CHIP 10K 5% 1/16W
R337 1-216-837-11 METAL CHIP 22K 5% 1/16W R866 1-216-821-11 METAL CHIP 1K 5% 1/16W
R338 1-216-825-11 METAL CHIP 2.2K 5% 1/16W R867 1-216-864-11 METAL CHIP 0 5% 1/16W
R868 1-216-821-11 METAL CHIP 1K 5% 1/16W
R339 1-216-821-11 METAL CHIP 1K 5% 1/16W R869 1-216-837-11 METAL CHIP 22K 5% 1/16W
R340 1-216-821-11 METAL CHIP 1K 5% 1/16W R870 1-216-864-11 METAL CHIP 0 5% 1/16W
R341 1-216-821-11 METAL CHIP 1K 5% 1/16W
R343 1-216-821-11 METAL CHIP 1K 5% 1/16W R871 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R348 1-216-821-11 METAL CHIP 1K 5% 1/16W R873 1-216-853-11 METAL CHIP 470K 5% 1/16W
R874 1-216-821-11 METAL CHIP 1K 5% 1/16W
R801 1-216-864-11 METAL CHIP 0 5% 1/16W R875 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R802 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R876 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R803 1-216-864-11 METAL CHIP 0 5% 1/16W
(US,CND,E92,MX) R879 1-216-813-11 METAL CHIP 220 5% 1/16W
R803 1-216-817-11 METAL CHIP 470 5% 1/16W R881 1-216-821-11 METAL CHIP 1K 5% 1/16W
(SP) R882 1-216-833-11 METAL CHIP 10K 5% 1/16W
R803 1-216-829-11 METAL CHIP 4.7K 5% 1/16W R883 1-216-833-11 METAL CHIP 10K 5% 1/16W
(AR) R885 1-216-841-11 METAL CHIP 47K 5% 1/16W

R803 1-216-833-11 METAL CHIP 10K 5% 1/16W R886 1-216-821-11 METAL CHIP 1K 5% 1/16W
(AUS) R887 1-216-821-11 METAL CHIP 1K 5% 1/16W
R804 1-216-864-11 METAL CHIP 0 5% 1/16W R889 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
(EXCEPT SP) R896 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R804 1-216-813-11 METAL CHIP 220 5% 1/16W R898 1-216-853-11 METAL CHIP 470K 5% 1/16W
(SP)
R805 1-216-864-11 METAL CHIP 0 5% 1/16W R899 1-216-841-11 METAL CHIP 47K 5% 1/16W
R806 1-216-864-11 METAL CHIP 0 5% 1/16W R951 1-216-845-11 METAL CHIP 100K 5% 1/16W
R952 1-249-421-11 CARBON 2.2K 5% 1/4W F
R807 1-216-864-11 METAL CHIP 0 5% 1/16W R954 1-249-413-11 CARBON 470 5% 1/4W F
R808 1-216-864-11 METAL CHIP 0 5% 1/16W R955 1-216-809-11 METAL CHIP 100 5% 1/16W
R809 1-216-821-11 METAL CHIP 1K 5% 1/16W
R810 1-216-864-11 METAL CHIP 0 5% 1/16W R956 1-249-413-11 CARBON 470 5% 1/4W F
R812 1-216-864-11 METAL CHIP 0 5% 1/16W R958 1-216-821-11 METAL CHIP 1K 5% 1/16W
R960 1-216-809-11 METAL CHIP 100 5% 1/16W

48
 CFD-G35
Ver 1.3 2002. 09
MAIN PDW POWER TC
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R961 1-216-821-11 METAL CHIP 1K 5% 1/16W < RESISTOR >
(CND,AUS,AR,SP)
R964 1-216-809-11 METAL CHIP 100 5% 1/16W R351 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R965 1-216-817-11 METAL CHIP 470 5% 1/16W R353 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R356 1-216-821-11 METAL CHIP 1K 5% 1/16W
< VIBRATOR > R357 1-216-817-11 METAL CHIP 470 5% 1/16W
R359 1-216-797-11 METAL CHIP 10 5% 1/16W
X801 1-781-775-21 VIBRATOR, CERAMIC 4.19MHz
X802 1-579-616-31 VIBRATOR, CRYSTAL 32.76kHz R360 1-216-797-11 METAL CHIP 10 5% 1/16W
************************************************************** R361 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R362 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
* A-3178-396-A PDW BOARD, COMPLETE(US,CND,E92,MX) R363 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
********************* R364 1-216-857-11 METAL CHIP 1M 5% 1/16W
* A-3178-479-A PDW BOARD,COMPLETE(AUS,AR,SP)
********************* R365 1-216-857-11 METAL CHIP 1M 5% 1/16W
3-238-233-01 CHASSIS (HS.R) R366 1-216-833-11 METAL CHIP 10K 5% 1/16W
3-703-150-11 CLAMP **************************************************************
4-960-167-01 SCREW (3X8) (DIA. 10), +WH
7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S * 1-684-451-11 POWER BOARD
*************
< CAPACITOR >
< CAPACITOR >
C351 1-104-665-11 ELECT 100uF 20.00% 10V
C352 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V C901 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C353 1-104-665-11 ELECT 100uF 20.00% 10V (US,CND,E92,MX)
C354 1-104-665-11 ELECT 100uF 20.00% 10V C901 1-115-339-11 CERAMIC CHIP 0.1uF 10.00% 50V
C355 1-104-665-11 ELECT 100uF 20.00% 10V (AUS,AR,SP)
C902 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C356 1-104-665-11 ELECT 100uF 20.00% 10V (US,CND,E92,MX)
C357 1-136-165-00 FILM 0.1uF 5.00% 50V C902 1-115-339-11 CERAMIC CHIP 0.1uF 10.00% 50V
(US,CND,E92,MX) (AUS,AR,SP)
C358 1-136-165-00 FILM 0.1uF 5.00% 50V C903 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
(US,CND,E92,MX) (US,CND,E92,MX)
C359 1-128-551-11 ELECT 22uF 20.00% 25V
C360 1-126-963-11 ELECT 4.7uF 20.00% 50V C903 1-115-339-11 CERAMIC CHIP 0.1uF 10.00% 50V
(AUS,AR,SP)
C361 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C904 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
C362 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V (US,CND,E92,MX)
(AUS,AR,SP) C904 1-115-339-11 CERAMIC CHIP 0.1uF 10.00% 50V
C363 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V (AUS,AR,SP)
(AUS,AR,SP)
C364 1-136-165-00 FILM 0.1uF 5.00% 50V < JACK >
(AUS,AR,SP)
C365 1-136-165-00 FILM 0.1uF 5.00% 50V 0 CNJ901 1-540-009-11 INLET, AC(US)
(AUS,AR,SP) 0 CNJ901 1-526-818-11 INLET, AC(E92,MX)
0 CNJ901 1-526-838-11 INLET, AC 2P(AUS,AR,SP)
C366 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
< CONNECTOR >
< CONNECTOR >
* CNP902 1-785-656-11 PIN, CONNECTOR (PC BOARD) 4P
* CNP351 1-785-656-21 PIN, CONNECTOR (PC BOARD) 4P * CNP903 1-785-657-11 PIN, CONNECTOR (PC BOARD) 5P
* CNP352 1-785-656-11 PIN, CONNECTOR (PC BOARD) 4P
< DIODE >
< DIODE >
D901 8-719-046-07 DIODE 2A02M
D351 8-719-991-33 DIODE 1SS133T-77 D902 8-719-046-07 DIODE 2A02M
D352 8-719-991-33 DIODE 1SS133T-77 D903 8-719-046-07 DIODE 2A02M
D904 8-719-046-07 DIODE 2A02M
< IC > **************************************************************

IC351 8-759-426-51 IC BA5417 A-3178-403-A TC BOARD, COMPLETE

*******************
< CABLE HOLDER >
3-222-726-01 CHASSIS (TC)
* KH353 1-565-386-11 HOLDER, CABLE 5P 7-685-783-09 SCREW +PTT 2X6 (S)

< TRANSISTOR > < CAPACITOR >

Q351 8-729-281-53 TRANSISTOR 2SC1815GR-TPE2 C101 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
Q354 8-729-011-92 TRANSISTOR 2SC2001TP-K1K2
The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.
49
CFD-G35
Ver 1.3 2002. 09
TC TRANS TUNER
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C102 1-104-665-11 ELECT 100uF 20.00% 10V R302 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
C103 1-165-176-11 CERAMIC CHIP 0.047uF 10.00% 16V
C104 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V R303 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
C105 1-162-923-11 CERAMIC CHIP 47PF 5% 50V R304 1-216-821-11 METAL CHIP 1K 5% 1/16W
R305 1-216-817-11 METAL CHIP 470 5% 1/16W
C107 1-162-962-11 CERAMIC CHIP 470PF 10% 50V R306 1-218-867-11 RES-CHIP 6.8K 5% 1/10W
C201 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V R307 1-216-797-11 METAL CHIP 10 5% 1/16W
C202 1-104-665-11 ELECT 100uF 20.00% 10V
C203 1-165-176-11 CERAMIC CHIP 0.047uF 10.00% 16V R308 1-216-837-11 METAL CHIP 22K 5% 1/16W
C204 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V R309 1-216-805-11 METAL CHIP 47 5% 1/16W
R314 1-216-817-11 METAL CHIP 470 5% 1/16W
C205 1-162-923-11 CERAMIC CHIP 47PF 5% 50V R315 1-216-817-11 METAL CHIP 470 5% 1/16W
C207 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C301 1-104-665-11 ELECT 100uF 20.00% 10V < SWITCH >
C302 1-104-665-11 ELECT 100uF 20.00% 10V
C303 1-104-665-11 ELECT 100uF 20.00% 10V S301 1-762-565-11 SWITCH, SLIDE (REC)

C304 1-126-947-11 ELECT 47uF 20.00% 10V < TRANSFORMER >

C305 1-162-962-11 CERAMIC CHIP 470PF 10% 50V
C306 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V T301 1-416-041-11 TRANSFORMER, BIAS OSCILLATION
C307 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V **************************************************************

< CONNECTOR > * 1-684-452-11 TRANS BOARD

************
CN303 1-568-830-11 CONNECTOR, FFC 11P
1-533-233-31 HOLDER, FUSE
< IC >
< FUSE >
IC301 8-759-264-71 IC TA2068N
0 F902 1-532-465-11 FUSE,TIME LAG 3.15A/250V(AUS,AR,SP)
< JUMPER RESISTOR > 0 F902 1-576-109-11 FUSE 5A/125V(US,E92,MX)

JC301 1-216-864-11 METAL CHIP 0 5% 1/16W < TRANSFORMER >

JC302 1-216-864-11 METAL CHIP 0 5% 1/16W
JC303 1-216-864-11 METAL CHIP 0 5% 1/16W 0 T901 1-437-644-11 TRANSFORMER, POWER(US,E92,MX)
JC304 1-216-864-11 METAL CHIP 0 5% 1/16W 0 T901 1-437-645-11 TRANSFORMER, POWER(AUS,AR,SP)
JC305 1-216-864-11 METAL CHIP 0 5% 1/16W **************************************************************

JC306 1-216-295-91 SHORT 0 * A-3323-779-A TUNER BOARD, COMPLETE (US,CND,E92,MX)

JC307 1-216-864-11 METAL CHIP 0 5% 1/16W **********************
JC308 1-216-295-91 SHORT 0
* A-3323-815-A TUNER BOARD, COMPLETE (AUS,AR,SP)
< TRANSISTOR > **********************

Q301 8-729-120-28 TRANSISTOR 2SC2412K-T-146-R < CAPACITOR >

< RESISTOR > C1 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

C4 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R101 1-216-835-11 METAL CHIP 15K 5% 1/16W C7 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50V
R102 1-216-807-11 METAL CHIP 68 5% 1/16W C8 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
R103 1-216-843-11 METAL CHIP 68K 5% 1/16W C9 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
R104 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
R105 1-216-835-11 METAL CHIP 15K 5% 1/16W C10 1-126-960-11 ELECT 1uF 20.00% 50V
C11 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V
R106 1-216-825-11 METAL CHIP 2.2K 5% 1/16W C12 1-126-963-11 ELECT 4.7uF 20.00% 50V
R110 1-216-809-11 METAL CHIP 100 5% 1/16W C13 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R111 1-216-829-11 METAL CHIP 4.7K 5% 1/16W C14 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
R112 1-216-835-11 METAL CHIP 15K 5% 1/16W (US,CND,E92,MX)
R201 1-216-835-11 METAL CHIP 15K 5% 1/16W
C14 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R202 1-216-807-11 METAL CHIP 68 5% 1/16W (AUS,AR,SP)
R203 1-216-843-11 METAL CHIP 68K 5% 1/16W C15 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
R204 1-216-827-11 METAL CHIP 3.3K 5% 1/16W (US,CND,E92,MX)
R205 1-216-835-11 METAL CHIP 15K 5% 1/16W C15 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R206 1-216-825-11 METAL CHIP 2.2K 5% 1/16W (AUS,AR,SP)
C18 1-126-934-11 ELECT 220uF 20.00% 10V
R210 1-216-025-11 RES-CHIP 100 5% 1/10W C20 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V
R211 1-216-829-11 METAL CHIP 4.7K 5% 1/16W
R212 1-216-835-11 METAL CHIP 15K 5% 1/16W C21 1-126-960-11 ELECT 1uF 20.00% 50V
R301 1-216-857-11 METAL CHIP 1M 5% 1/16W
The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.
50
 CFD-G35
Ver 1.1 2002. 05
TUNER
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C22 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V < IC >
C23 1-126-960-11 ELECT 1uF 20.00% 50V
C24 1-162-960-11 CERAMIC CHIP 220PF 10% 50V IC1 6-700-512-01 IC TA2149BN
C26 1-162-927-11 CERAMIC CHIP 100PF 5% 50V IC2 8-759-483-40 IC LC72137M-TLM

C27 1-162-927-11 CERAMIC CHIP 100PF 5% 50V < JUMPER RESISTOR >
C29 1-104-665-11 ELECT 100uF 20.00% 10V
C30 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V JC1 1-216-864-11 METAL CHIP 0 5% 1/16W
C31 1-162-919-11 CERAMIC CHIP 22PF 5% 50V JC2 1-216-864-11 METAL CHIP 0 5% 1/16W
C32 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V JC3 1-216-864-11 METAL CHIP 0 5% 1/16W
JC4 1-216-864-11 METAL CHIP 0 5% 1/16W
C33 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V JC5 1-216-864-11 METAL CHIP 0 5% 1/16W
C34 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C35 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V JC6 1-216-864-11 METAL CHIP 0 5% 1/16W
C37 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V JC11 1-216-864-11 METAL CHIP 0 5% 1/16W
C39 1-107-826-11 CERAMIC CHIP 0.1uF 10.00% 16V JC12 1-216-864-11 METAL CHIP 0 5% 1/16W
JC13 1-216-864-11 METAL CHIP 0 5% 1/16W
C41 1-164-230-11 CERAMIC CHIP 220PF 5.00% 50V JC24 1-216-864-11 METAL CHIP 0 5% 1/16W
C42 1-162-927-11 CERAMIC CHIP 100PF 5% 50V (AUS,AR,SP)
C43 1-162-919-11 CERAMIC CHIP 22PF 5% 50V
C47 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V JC33 1-216-864-11 METAL CHIP 0 5% 1/16W
C49 1-161-051-00 CERAMIC 0.01uF 10% 50V JC34 1-216-864-11 METAL CHIP 0 5% 1/16W

C51 1-162-919-11 CERAMIC CHIP 22PF 5% 50V < COIL >

C52 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V
C53 1-136-169-00 FILM 0.22uF 5.00% 50V L1 1-409-775-11 COIL, AIR-CORE
C54 1-126-934-11 ELECT 220uF 20.00% 10V L2 1-416-509-11 COIL, AIR-CORE
C55 1-162-927-11 CERAMIC CHIP 100PF 5% 50V L3 1-428-947-11 COIL, FERRITE-ROD ANTENNA
L3 1-754-117-11 ANTENNA, FERRITE-ROD (MW)
C56 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V L4 1-411-234-21 COIL, AM OSC
C57 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C59 1-162-927-11 CERAMIC CHIP 100PF 5% 50V L11 1-414-142-11 INDUCTOR 1uH(US,E92,MX)
C60 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V L21 1-410-509-11 INDUCTOR 10uH
C61 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
< RESISTOR >
C62 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C63 1-162-927-11 CERAMIC CHIP 100PF 5% 50V R1 1-216-815-11 METAL CHIP 330 5% 1/16W
C65 1-126-963-11 ELECT 4.7uF 20.00% 50V R2 1-216-817-11 METAL CHIP 470 5% 1/16W
C66 1-162-927-11 CERAMIC CHIP 100PF 5% 50V R3 1-216-833-11 METAL CHIP 10K 5% 1/16W
C68 1-162-927-11 CERAMIC CHIP 100PF 5% 50V R4 1-216-833-11 METAL CHIP 10K 5% 1/16W
R10 1-216-805-11 METAL CHIP 47 5% 1/16W
C77 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
(AUS,AR,SP) R11 1-216-827-11 METAL CHIP 3.3K 5% 1/16W
C78 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V R13 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
(AUS,AR,SP) R24 1-216-813-11 METAL CHIP 220 5% 1/16W
C80 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V R30 1-216-835-11 METAL CHIP 15K 5% 1/16W
C95 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V R31 1-216-827-11 METAL CHIP 3.3K 5% 1/16W

< FILTER > R32 1-216-845-11 METAL CHIP 100K 5% 1/16W

R40 1-216-849-11 METAL CHIP 220K 5% 1/16W
CF2 1-760-233-71 FILTER, CERAMIC R41 1-216-833-11 METAL CHIP 10K 5% 1/16W
CF4 1-781-962-21 FILTER, CERAMIC R50 1-216-821-11 METAL CHIP 1K 5% 1/16W
R51 1-216-833-11 METAL CHIP 10K 5% 1/16W
< CONNECTOR >
R52 1-216-864-11 METAL CHIP 0 5% 1/16W
* CNP1 1-564-713-11 PIN, CONNECTOR (SMALL TYPE)11P R53 1-216-835-11 METAL CHIP 15K 5% 1/16W
R54 1-216-817-11 METAL CHIP 470 5% 1/16W
< TRIMMER > R56 1-216-815-11 METAL CHIP 330 5% 1/16W
R58 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
CT1 1-141-603-11 CAP, ADJ
CT3 1-141-601-11 CAP, ADJ R59 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R60 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
< DIODE > R61 1-216-825-11 METAL CHIP 2.2K 5% 1/16W
R63 1-216-833-11 METAL CHIP 10K 5% 1/16W
D1 8-719-078-48 DIODE KV1471ETR1-3 R65 1-216-833-11 METAL CHIP 10K 5% 1/16W
D2 8-719-078-48 DIODE KV1471ETR1-3
D3 8-719-050-69 DIODE KV1520NT R91 1-216-813-11 METAL CHIP 220 5% 1/16W
D10 8-719-988-61 DIODE 1SS355TE-17 R92 1-216-813-11 METAL CHIP 220 5% 1/16W
D11 8-719-988-61 DIODE 1SS355TE-17 R94 1-216-821-11 METAL CHIP 1K 5% 1/16W

51
CFD-G35
Ver 1.4 2002. 11
TUNER
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< TRANSFORMER > SP391 1-825-029-11 SPEAKER (10cm)(BLACK)
SP391 1-825-159-11 SPEAKER (10cm)(SILVER)
T1 1-433-741-11 TRANSFORMER, IF SP392 1-825-029-11 SPEAKER (10cm)(BLACK)
T2 1-419-465-11 COIL (DET) SP392 1-825-159-11 SPEAKER (10cm)(SILVER)
SP393 1-825-030-11 SPEAKER (8cm) (WOOFER)
< VIBRATOR > **************************************************************

X1 1-781-592-11 VIBRATOR, CRYSTAL 75kHz (US,CND,E92,MX) ACCESSORIES

X1 1-760-130-11 VIBRATOR, CRYSTAL 75kHz (AUS,AR,SP) ************
**************************************************************
A-3170-228-A REMOTE COMMANDER (RMT-CEX35AD)
MISCELLANEOUS (SILVER)
*************** A-3170-229-A REMOTE COMMANDER (RMT-CG35A)
(BLACK)
9 1-823-740-11 CABLE, FLEXIBLE FLAT (26 CORE) 0 1-557-287-11 CORD, POWER (E92,MX)
17 1-823-744-11 CABLE, FLEXIBLE FLAT (4 CORE) 0 1-575-131-11 CORD, POWER (SP)
58 1-452-899-11 MAGNET 0 1-696-819-11 CORD, POWER (AUS)
103 1-757-778-11 CABLE, FLEXIBLE FLAT (11 CORE)
123 1-823-742-11 WIRE (FLAT TYPE) (14 CORE) 0 1-783-878-11 CORD, POWER (US,CND)
0 1-783-952-11 CORD, POWER (AR)
124 1-757-689-11 CABLE, FLEXIBLE FLAT (16 CORE) 3-027-153-01 LID, BATTERY CASE (FOR RMT-CG35A)
0 251 8-820-161-02 OPTICAL PICK-UP KSS-213R 3-027-153-11 LID, BATTERY CASE (FOR RMT-CEX35AD)
ANT1 1-501-883-21 ANTENNA, TELESCOPIC 3-241-303-11 MANUAL, INSTRUCTION (ENGLISH)
HE301 1-543-876-11 HEAD (ERASE) (US,CND,E92,MX)
HRP301 1-500-691-11 HEAD,MAGNETIC(RECORD/PLAYBACK)
3-241-303-21 MANUAL, INSTRUCTION (FRENCH) (CND)
M321 A-3320-446-A MOTOR, ASSY (CAPSTAN/REEL) 3-241-303-31 MANUAL, INSTRUCTION (SPANISH) (E92,MX)
M701 X-2162-712-1 GEAR ASSY (R) (RP), MOTOR (SLED) 3-241-303-41 MANUAL, INSTRUCTION (ENGLISH,SPANISH)
S321 1-771-686-11 SWITCH, LEAF (PLAY SW) (AUS,AR,SP)
S322 1-762-679-11 SWITCH, LEAF (MOTOR SW)
S801 1-692-960-11 SWITCH, PUSH (1 KEY) (ZPUSH OPEN/CLOSE) The components identified by Les composants identifiés par
mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.

52
 CFD-G35

MEMO

53
CFD-G35

REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.

Ver. Date Description of Revision

1.0 2002.03 New
1.1 2002.05 Addition of Australian, Argentina and Singapore model (ENG-02014)

1.2 2002.07 Ref.No.251, 258 and M701 changed into the parts only for services
(SPM-02027)

1.3 2002.09 Addition of Canadian model (ENG-02033)

1.4 2002.11 Correction of parts numbers of remote commanders (SPM-02051)