ME354-Tut11sol w07 PDF

ME 354 Tutorial, Week#13
Reacting Mixtures
Question 1:
Determine the mole fractions of the products of combustion when octane,
C8H18, is burned with 200% theoretical air. Also, determine the air-fuel
ratio and the dew-point temperature of the products if the pressure is 0.1
MPa.
Step 1: Draw a diagram to represent the system
Step 2: State your assumptions

Assumptions:
1) Combustion is complete
2) Combustion gases are ideal gases
3) Steady operating conditions exist
Step 3: Solve
Before we start the solution to this problem let us examine the general
cases of complete combustion to develop a procedure for balancing the
reaction equations.
For Excess Air and Complete Combustion
Let (1+a) = the percent of theoretical air, where “a” is the percentage of
excess air. [For example, for 300% theoretical air (200% excess air),
(1+a)=3 so a=2].
The problem states that octane, C8H18, is combusted with 200%

theoretical air (or 100% excess air) so a =1. Using the formulas developed
for the general case with excess air the stochiometric coefficients can be
determined as shown below.
1
C: →
H: → So,
O: → So, (corrected)
N: → So, (corrected)
The balanced reaction equation is shown below in Eq1.
……Eq 1
[a] The total moles of products, Nproducts, can be determined by adding the
number of moles of each product as shown below.
NCO2 = 8 Kmole
NH2O = 9 Kmole
NO2 = 12.5 Kmole
NN2 = 94 Kmole
Nproducts=(8+9+12.5+94)=123.5 Kmole
The mole fractions, yi, of each component are determined below:
yCO2 = NCO2/Nproducts = (8/123.5) = 6.47%

yH2O = NH2O/Nproducts = (9/123.5) = 7.29%
Answer 1a)
yO2 = NO2/Nproducts = (12.5/123.5) = 10.12%
YN2 = NN2/Nproducts = (94/123.5) = 76.12%
[b] The air-Fuel Ratio, ………Eq.-2
Where
{From Balanced Reaction Equation}
{From Table A-2 of Text Book}
Similarly.
Where
{From Balanced Reaction Equation}
2
So,
From Equation 2, substituting all values, we get,
The dew-point temperature of the products is the temperature at which

the water vapor in the products starts to condense as the products are
cooled. This is the saturated temperature corresponding to the pressure
of H2O (i.e. the partial pressure of H2O in the mixture). Since it is
assumed that the combustion gases behave as ideal gases, the partial
pressure of H2O can be determined from the total pressure multiplied by
the mole fraction of H2O, yH2O.
→PH2O = yH2OP=(0.0729)(0.1 [MPa]) = 7.29 kPa
From Table A-4, interpolating in between 35°C and 40°C
Answer 1b)
3
Question 2:
A small gas turbine uses C8H18 (l) for fuel, with 400% theoretical air. The
air and fuel enter at 25°C and the products of combustion leave at 900K.
The output of the engine and the fuel consumption are measured, and it
is found that the specific fuel consumption is 0.25 kg/s of fuel per
megawatt output. Determine the heat transfer from the engine per kmol
of fuel. Assume complete combustion.
Step 1: Draw a diagram to represent the system
Step 2: State your assumptions

Assumptions:
1) Combustion is complete
2) Combustion gases are ideal gases
3) Δke, Δpe ≈ 0
4) steady operating conditions exist
Step 3: Solve
Using the procedures developed in Question #1, the reaction equation
can be balanced for 400% theoretical air (a=3) as shown below.
C’s →
H2’s →
O2’s →
N2’s →
In order to determine the heat transfer from the system a first law
analysis can be performed on the combustion chamber. A general first
law equation for combustion analysis (on a “per mole of fuel basis”) is
shown in Eq1.
(Eq1)
4
The heat transfer and work will be assumed to be out of the system so
Qin & Win terms are zero. The enthalpies for the reactants will be
determined first. Note: the circle superscript is used to denote that the
property value is referenced to a 25°C, 1atm reference state.
Reactants (C8H18, O2, and N2)

Enthalpy of formation,
For stable elements O2 and N2, the enthalpy of formation is zero
→ =0
→ =0
The enthalpy of formation for C8H18 (l), is found in Table A-26

→ = –249950 kJ/kmol
Ideal Gas Enthalpy relative to reference state,

In the term, the term is the ideal gas enthalpy at the
temperature of interest and is the ideal gas enthalpy at the reference
temperature. By subtracting from the ideal gas enthalpy at the
temperature of interest is referenced to an ideal gas enthalpy of zero at
the reference state. Doing this for all the reactants and products ensures
that all the enthalpy values are referenced to the same reference state
(25°C, 1atm) and are thus comparable.
Since the reactants are already at the reference state, = 0 for all the
reactants.
→ =0
→ =0
→ =0
Products (CO2, H2O, O2, and N2)

Enthalpy of formation,
For stable elements O2 and N2, the enthalpy of formation is zero
→ =0
→ =0
5
The enthalpy of formations for CO2 and H2O(g), and located in Table A-26
→ = –393520 kJ/kmol
→ = –241820 kJ/kmol
Ideal Gas Enthalpy relative to reference state,

Since the products are at 900K, at 900K must first be determined and
then at the reference state of 25°C/298K (this is ) must be
subtracted to ensure the enthalpies are all calculated with respect to the
same reference state.
For CO2,
= 37405 kJ/kmol (Table A-20)
= 28041 kJ/kmol
For H2O (g),

= 21924 kJ/kmol
For O2,
= 19246 kJ/kmol
For N2,
= 18221 kJ/kmol
The specific fuel consumption is given as 0.25 kg/s of fuel per megawatt
output of the engine. This information can be used to find Wout as shown
below.
6
Note: The molar mass of C8H18 was determined from the molar mass of C
(12.012kg/kmol) and H (1.008kg/kmol)
Mfuel=8(12.012)+18(1.008) = 114.24kgfuel/kmol.
Eq1 can be rearranged to isolate for Qout as shown in Eq2.
(Eq2)
Substituting in the values determined above into Eq2 the heat transfer
from the engine is determined. Note: the number of moles of each
product are determined using the balanced reaction equation: NCO2=8,
NH2O=9, NO2 =37.5, and NN2 = 188.
Answer 2)

ME354-Tut11sol w07 PDF

Uploaded by

Copyright:

Available Formats

ME354-Tut11sol w07 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ME354-Tut11sol w07 PDF

Uploaded by

Copyright:

Available Formats

ME 354 Tutorial, Week#13

Step 1: Draw a diagram to represent the system

Step 2: State your assumptions

For Excess Air and Complete Combustion

The problem states that octane, C8H18, is combusted with 200%

The balanced reaction equation is shown below in Eq1.

The mole fractions, yi, of each component are determined below:

yCO2 = NCO2/Nproducts = (8/123.5) = 6.47%

[b] The air-Fuel Ratio, ………Eq.-2

{From Table A-2 of Text Book}

From Equation 2, substituting all values, we get,

The dew-point temperature of the products is the temperature at which

→PH2O = yH2OP=(0.0729)(0.1 [MPa]) = 7.29 kPa

From Table A-4, interpolating in between 35°C and 40°C

Step 1: Draw a diagram to represent the system

Step 2: State your assumptions

Reactants (C8H18, O2, and N2)

The enthalpy of formation for C8H18 (l), is found in Table A-26

Ideal Gas Enthalpy relative to reference state,

Products (CO2, H2O, O2, and N2)

Ideal Gas Enthalpy relative to reference state,

For H2O (g),

Eq1 can be rearranged to isolate for Qout as shown in Eq2.

You might also like