ARTICLE IN PRESS

Journal of Solid State Chemistry 182 (2009) 2456–2460

Contents lists available at ScienceDirect

Journal of Solid State Chemistry

journal homepage: www.elsevier.com/locate/jssc

Preparation of iron oxides using ammonium iron citrate precursor: Thin films
and nanoparticles
Sangmoon Park a,b,c,
a
Department of Engineering in Energy and Applied Chemistry, Silla University, Busan 617-736, Republic of Korea1
b
USC NanoCenter, Department of Chemistry and Biochemistry, University of South Carolina, 1212 Greene Street, Columbia, SC 29208-0001, USA2
c
Condense Matter Physics and Materials Science Department, Brookhaven National Laboratory, Upton, NY 11973-5000, USA2

a r t i c l e in f o a b s t r a c t

Article history: Ammonium iron citrate (C6H8O7  nFe  nH3N) was used as a precursor for preparing both iron-oxide thin
Received 8 March 2009 films and nanoparticles. Thin films of iron oxides were fabricated on silicon (111) substrate using a
Received in revised form successive-ionic-layer-adsorption-and-reaction (SILAR) method and subsequent hydrothermal or
16 June 2009
furnace annealing. Atomic force microscopy (AFM) images of the iron-oxide films obtained under
Accepted 17 June 2009
various annealing conditions show the changes of the micro-scale surface structures and the magnetic
Available online 24 June 2009
properties. Homogenous Fe3O4 nanoparticles around 4 nm in diameter were synthesized by
Keywords: hydrothermal reduction method at low temperature and investigated using transmission electron
Iron oxides microscopy (TEM).
Thin films
& 2009 Elsevier Inc. All rights reserved.
Nanoparticles
Transmission electron microscopy
Magnetic measurements

1. Introduction lizers under high pressure and high temperature leads to

insoluble materials due to their dissolution–recrystallization
Iron oxides (Fe2O3 and Fe3O4) are technologically important process [30]. The reduction route refers to gaining electrons in
materials engaged in the gas sensors [1–5], tunneling magnetore- process from reducing agent on the basis of the value of standard
sistance (TMR) [6,7], recording medium [8,9], biocompatibility Gibbs free energy change (DG0). The hydrothermal synthesize of
[10–13], and medical application [10,14]. A variety of deposition magnetite (Fe3O4) and maghemite (g-Fe2O3) nanoparticles at a
methods like molecular-beam epitaxy (MBE) [15], sputtering [6], low temperature have been used [31–35]. Iron nitrate 9-hydrate
pulsed laser deposition (PLD) [16,17], metallo-organic deposition and ferrocene for synthesizing iron-oxide nanoparticles were
(MOD) [18], plasma enhanced chemical vapor deposition (PECVD) specially utilized as iron precursors along with surfactants as
[19], and atomic layer deposition (ALD) [20] have been widely well as reducing agent (hydrazine) [31,32]. Furthermore, a
used to fabricate iron-oxide films. It was shown that many metal- (NH4)2SO4  FeSO4  6H2O precursor only in the presence of
oxide films have been accomplished, using the successive-ionic- hydrazine was also exploited for the formation of iron oxides [33].
layer-adsorption-and-reaction (SILAR) deposition as a low-cost I herein report both the fabrication of iron-oxide films and
and simple fabrication technique [21–23]. Moreover, the combi- synthesis of iron-oxide nanoparticles using ammonium iron
nation of SILAR deposition followed by hydrothermal dehydration citrate as a complexing precursor. The deposition and crystal-
and annealing became a process for preparing homogenous and lization of iron-oxide films on the use of SILAR method followed
crystallized metal-oxide films at quite low temperature. by hydrothermal and/or furnace annealing were performed. The
Nanoscale materials in applied single-electron devices, cata- surface topography of iron-oxide films was investigated by AFM
lysts, and optical/electrical/magnetic devices have been inten- images, and their magnetic susceptibility (w) as a function of field
sively studied and such nanomaterials have been synthesized by (H) was attained as well. A simple hydrothermal-reduction
using hydrothermal and reduction process [24–29]. The hetero- process at 150 1C was used for synthesizing homogenous iron-
geneous reaction in the presence of aqueous solvent or minera- oxide nanoparticles about 4 nm in diameter.

 Corresponding author at: Department of Engineering in Energy and Applied 2. Experimental details
Chemistry, Silla University, Busan 617-736, Republic of Korea.
Fax: +82 51 999 5806.
E-mail address: spark@silla.ac.kr
Iron-oxide films on Si (111) substrate were prepared
1
Current address. using aqueous solutions of 0.15 g ammonium iron citrate
2
Previous address. (C6H8O7  nFe  nH3N Alfa, 99.998%) and 0.03 M NaOH (Analytical

0022-4596/$ - see front matter & 2009 Elsevier Inc. All rights reserved.
doi:10.1016/j.jssc.2009.06.027
 ARTICLE IN PRESS
S. Park / Journal of Solid State Chemistry 182 (2009) 2456–2460 2457

Reagent). The substrates were attached to the arm of a Gilson 223

XYZ robotic sample changer and immersed in the Fe-complexing
solution, water, NaOH solution, and water for 0.03, 0.06, 0.03, and
0.096 min (700 cycles), respectively. The water prepared in the use
of a Millipore Milli-Q AcademicTM ion-exchange system was
vigorously stirred near the substrate using a magnetic stir bar in
rinse bath. As-made films were cut into four pieces and then each
piece of film was transferred to a sealed Teflon-lined Parr
ReactorTM. The films were hydrothermally heated at 200 1C,
directly annealed in air at 600 1C, or annealed under 4% H2/Ar at
600 1C in a furnace. X-ray diffraction measurements using CuKa
radiation were done using a MiniFlex+ (Rigaku) diffractometer.
The surface topography was examined with a NanoScopeII atomic
force microscopy (AFM, tapping mode). Magnetization measure-
ments were carried out using a SQUID magnetometer in the
temperature at 300 K at applied fields 20 kOerHr20 kOe. Fig. 1. X-ray diffraction patterns of calculated: (a) a-Fe2O3 (ICSD 22505), (b) Fe3O4
For the synthesis of iron-oxide nanoparticles, 5 mL distilled (ICSD 30860), (c) g-Fe2O3 (ICSD 79196) and observed iron-oxide thin films (d)
water was added to a Teflon-lined Parr reactorTM in a capacity of hydrothermal at 200 1C, (e) in air at 600 1C and (f) under 4% H2/Ar at 600 1C.
23 mL and then 0.02 g ammonium iron citrate precursor was
dissolved in water with stirring for 15 min. Finally, 3 mL
N2H4  H2O was slowly added to the solution. The solution was respectively. The 3D views at the 5 mm scale AFM images are
sealed in an autoclave and maintained at 150 1C for 18 h. When the shown in Fig. 2. Cross-sectional scanning electron microscopy of
reaction was finished, the black-solid products were obtained. The as-made films revealed thickness not greater than 150 nm that is
products were washed with ethanol using a centrifuge and then not shown in this report. Like ZrO2 [21], CeO2 [22], and TiO2 [23]
stored in ethanol to prevent oxidation. Transmission electron films prepared by SILAR technique, the as-deposited iron-oxide
microscopy (Hitachi H-8000, 200 kV) was used for the typical films reveal similar results of homogenously closely packed
morphologies of iron-oxide nanoparticles. nanoparticles with approximately 25 nm diameters. In
accordance with the broad XRD peaks of the iron-oxide films
annealed hydrothermally at 200 1C in Fig. 1(d), the homogenous
3. Results and discussion nanoparticles on the films are observed by the AFM image in
Fig. 2(a). The grain morphology of the furnace annealed iron-oxide
The SILAR method could be one of the thin film deposition films in air or under H2/Ar at 600 1C occurs much bigger than
techniques in addition to a variety of iron-oxide fabrication the one observed in hydrothermally annealed films. As shown in
methods as described above. It is essential to choose a metal Fig. 2(c) and (d), the grain morphology of the furnace annealed
cation constituent for preparing homogenous films in point of iron-oxide films at 600 1C is a couple of hundred nanometers
SILAR deposition method. Iron nitrate 9-hydrate could be utilized large, showing substantial surface roughness. The partial
for the one of typical iron-oxide precursors. For preparing iron- demagnetization curves for iron-oxide films were plotted
oxide nanoparticles, the precursor needs to be used with complex at 300 K. The demagnetization curves for the as-made films
surfactant species like sodium bis(2-ethylhexly)sulfosuccinate, (Fig. 2(a)) and furnace-annealed films in air at 600 1C (Fig. 2(c))
and moreover, it is known as a hydroscopic chemical as well as an were perturbed downwards by 20 kOe. While the curve
acidic reagent, when dissolved in water. The ammonium iron for hydrothermal annealed films exhibits an unsaturated
citrate was selected as a cation constituent, NHþ 
4 ½FeðOHÞcitrate . magnetism, the curve for furnace-annealed films under H2/Ar at
Its advantages over the common precursor are that this simple 600 1C shows a saturated magnetism around 500 Oe. These films
complex precursor can diminish the rapid aggregations of metal annealed under reducing environment (H2/Ar) might be magnetic
cation and hydroxide anion without a surfactant, it can be handled g-Fe2O3 or Fe3O4, which have two oxidation valence states
easily in air, and Fe-complexing in solution showing the mild (Fe2+ and Fe3+). The iron-oxide films annealed in air at 600 1C
pH (5) can be gently precipitated with anions (OH) along with show diamagnetic behavior, and thus they are non-magnetic
a potential/pH diagram, a pourbaix diagram. All films were a-Fe2O3 films, which have an oxidation valence state (Fe3+).
characterized by X-ray powder diffraction to identify the iron- Interestingly, when as-made films were hydrothermally annealed
oxide phases present. The ICSD data (a-Fe2O3 22505, Fe3O4 30860, at 200 1C, the iron-oxide films show superparamagnetic behavior
g-Fe2O3 79196) were used for indexing the observed iron-oxide due to that the coercive force is negligible as shown in Fig. 2(b)
phases shown in Fig. 1(a–f). XRD patterns of Fe3O4 and g-Fe2O3 are [31]. The iron-oxide films at a low temperature (200 1C) were not
intricate to distinguish two phases even though they have fully capable of being transformed to a-Fe2O3 phase due to the
different space groups, Fd3m for Fe3O4 and P4332 for g-Fe2O3. lack of oxygen sources in sealed hydrothermal vessel. When
Furthermore, both oxides show ferromagnetic behavior in as-deposited films with water as an oxygen source were placed in
magnetic property [36]. The broad Si (111) substrate peak on all the hydrothermal reactor, the phase of iron oxides was clearly
films was observed around 2y ¼ 2829 in Fig. 1(d–f). The (311) transformed to a-Fe2O3. It is associated with the presence of a
g-Fe2O3 (or Fe3O4) peak (*) around 2y35.9 was observed from sufficient oxygen source (water) to oxidize the films. In the cubic
XRD patterns (Fig. 1(d) and (f)) of both films annealed by inverse spinel Fe3O4 structure, Fe3+ ions occupy tetrahedral and
hydrothermal dehydration and under reduction environment. octahedral sites and Fe2+ ions are in tetrahedral site. It is known
When the films were annealed in air, the (104) and (110) that the aligned antiparallel spins of Fe3+ ions, which occupy
a-Fe2O3 peaks () around 2y33.4, 35.8 were obtained in Fig. 1(e). octahedral and tetrahedral sites, lead magnetic moment [37,38].
Fig. 2 shows the AFM images and the partial magnetic curves The unsaturated magnetic behavior observed in hydrothermally
of iron-oxide films, which were (a) as-deposited, (b) annealed films at 200 1C is attributed to the lack of the formation
hydrothermally dehydrated and annealed at 200 1C, (c) furnace of the magnetic domains. However, the furnace-annealed films
annealed in air at 600 1C, and (d) under 4% H2/Ar at 600 1C, under reducing environment show the saturated magnetic
 ARTICLE IN PRESS
2458 S. Park / Journal of Solid State Chemistry 182 (2009) 2456–2460

Fig. 2. AFM images and the partial magnetic curves (the inset M–H data corresponds to H from 4 to 4 kOe) of iron oxides: (a) as-deposited, (b) hydrothermal annealed at
200 1C, (c) furnace annealed in air, (d) under 4% H2/Ar at 600 1C.
 ARTICLE IN PRESS
S. Park / Journal of Solid State Chemistry 182 (2009) 2456–2460 2459

as shown in Fig. 3. In X-ray diffraction patterns, five intense peaks

are indexed by (220), (311), (400), (511), and (440), which are
matched with Fe3O4 and g-Fe2O3 phases. The relatively broad
peaks (k) around 2y18.5, 37.5 are indexed by (111), (222)
Fe3O4 diffractions. It is hard to tell apart whether the product is
Fe3O4 or g-Fe2O3 phase, but the X-ray diffraction analysis indicates
that possibly it is close to Fe3O4 nanoparticles. No preferred
orientation from the powder X-ray diffraction of Fe3O4 nano-
particles was detected.
Transmission electron microscopy (TEM) provides the typical
morphologies of as-synthesized Fe3O4 in Fig. 4. TEM images
indicate a very uniform size distribution of Fe3O4 nanoparticles.
Previously, the size-controlled synthesis for magnetic Fe3O4
nanoparticles was performed for the first time in the use of
Fe(acac)3 in phenyl ether, alcohol, oleic acid, and oleylamine [39].
In this work, Fe3O4 nanoparticles around 4 nm in diameter (Fig. 4)
Fig. 3. X-ray diffraction patterns of calculated (a) g-Fe2O3 (ICSD 79196), (b) Fe3O4
were also able to be generated by the use of ammonium iron
(ICSD 30860) and observed (c) Fe3O4 nanoparticles. citrate precursor, hydrazine, and water. Using the hydrothermal
reduction method, the synthesis of homogeneous Fe3O4
nanoparticles doped with metals such as Au, Ag, or Pt applying
to the biomedical purpose is underway.

4. Conclusions

Ammonium iron citrate was readily chosen as a precursor to

fabricate iron-oxide films and prepare nanoparticles. Iron-oxide
films were successfully deposited on Si wafer using SILAR method.
As the results of XRD and magnetic investigations, the g-Fe2O3 or
the Fe3O4 phase was obtained by hydrothermal or furnace-
annealed (under H2/Ar) films and a-Fe2O3 phase was achieved
by furnace-annealed (in air) films. AFM images of iron-oxide films
reveal different morphologies under various annealing conditions.
Especially homogenous Fe3O4 nanoparticles about 4 nm in
diameter were synthesized by hydrothermal reduction method,
and the morphology was investigated by TEM.

Acknowledgments

I am grateful to Dr. T. Vogt and Dr. K. Kang for their fruitful

discussions and help.

References

[1] L. Huo, W. Li, L. Lu, H. Cui, S. Xi, J. Wang, B. Zhao, Y. Shen, Z. Lu, Chem. Mater.
12 (2000) 790.
[2] O.K. Tan, W. Zhu, Q. Yan, L.B. Kong, Sens. Acutators B 65 (2000) 361.
Fig. 4. TEM image of Fe3O4 nanoparticles. [3] N. Yamazoe, N. Miura, Sens. Acutators B 20 (1994) 95.
[4] W. Göpel, Sens. Acutators B 18–19 (1994) 1.
[5] M. Matsuoka, Y. Nakatani, H. Ohido, Natl. Tech. Rep. 24 (1978) 461.
behavior because the energy barriers can be overcome when films [6] Y. Peng, C. Park, D.E. Laughlin, J. Appl. Phys. 93 (2003) 7957.
[7] K.-I. Aoshima, S.X. Wang, J. Appl. Phys. 93 (2003) 7954.
were heated at a high temperature (600 1C). [8] W. Yi, W. MoberlyChean, V. Narayanamurit, Y.F. Hu, Q. Li, I. Kaya, M. Burns,
As mentioned above, nanosized iron oxides have been D.M. Chen, J. Appl. Phys. 95 (2004) 7136.
synthesized using various precursors in the hydrothermal reduc- [9] J.C. Mallinson, The Foundations of Magnetic Recording, Academic, Berkeley,
1987.
tion method. The ammonium iron citrate as a precursor for [10] Y. Qiang, J. Antony, M.G. Marino, S. Pendyala, IEEE Trans. Magn. 40 (2004)
preparing iron-oxide nanoparticles was not used previously, to my 3538.
knowledge. The ammonium iron citrate is easy to dissolve in [11] D.K. Kim, M. Mikhaylova, Y. Zhang, M. Muhammed, Chem. Mater. 15 (2003)
1617.
water ðNHþ 
4 ½FeðOHÞcitrate Þ presenting mild pH5, and more- [12] M. Tada, S. Hatanaka, H. Sanbonsugi, N. Matsushita, M. Abe, J. Appl. Phys. 93
over, this complex precursor can play a role of a surfactant during (2003) 7566.
hydrolysis process to form homogeneous nanoparticles. When the [13] M. Chen, S. Yamamuro, D. Farrell, S.A. Majetich, J. Appl. Phys. 93 (2003) 7551.
[14] U. Häfeli, W. Schütt, J. Teller, M. Zborowski, Scientific and Clinical Application
ammonium iron citrate was dissolved in water, N2H4  H2O was
of Magnetic Carriers, Plenum Press, New York, 1997.
slowly added to the solution. The color of solution turned into [15] D.M. Lind, S.M. Berry, G. Chern, H. Mathias, L.R. Testardi, Phys. Rev. B 45
black from colorless. The hydrothermal reduction process at (1992) 1838.
150 1C using a Teflon-lined Parr reactorTM was performed. Black [16] C.A. Klient, H.C. Semmelhack, M. Lorenz, M.K. Krause, J. Magn. Magn. Mater.
725 (1995) 140.
solid products were attained after the reaction. The product was [17] W.L. Zhou, K.-Y. Wang, C.J. O’Connor, J. Tang, J. Appl. Phys. 89 (2001) 7398.
characterized by X-ray powder diffraction for phase identification [18] S. Xue, W. Ousi-Benomar, R.A. Lessard, Thin Solid Films 250 (1994) 194.
 ARTICLE IN PRESS
2460 S. Park / Journal of Solid State Chemistry 182 (2009) 2456–2460

[19] Y. Liu, W. Zhu, O.K. Tan, Y. Shen, Mater. Sci. Eng. 47 (1997) 171. [30] K. Byrappa, M. Yoshimura, Handbook of Hydrothermal Technology: A
[20] O. Nilsen, M. Lie, S. Foss, H. Fjellvag, A. Kjekshus, Appl. Surf. Sci. 227 (2004) 40. Technology for Growth and Materials Processing, William Andrew Publishing,
[21] S. Park, B.L. Clark, D.A. Keszler, J.P. Bender, J.F. Wager, T.A. Reynolds, 2001 p. 7.
G.S. Herman, Science 297 (2002) 65. [31] Y.-H. Zheng, Y. Cheng, F. Bao, Y.-S. Wang, Mater. Res. Bull. 41 (2006) 525.
[22] S. Park, G.S. Herman, D.A. Keszler, J. Solid State Chem. 175 (2003) 84. [32] G. Zou, K. Xiong, C. Jiang, H. Li, T. Li, J. Du, Y. Qian, J. Phys. Chem. 109 (2005)
[23] S. Park, E. DiMasi, Y.-I. Kim, W. Han, P.M. Woodward, T. Vogt, Thin Solid Films 18356.
515 (2006) 1250. [33] Y. Li, H. Liao, Y. Qian, Mater. Res. Bull. 33 (1998) 841.
[24] Y. Jin, K. Tang, C. An, L. Huang, J. Crystal Growth 253 (2003) 429. [34] D. Chen, R. Xu, J. Solid State Chem. 137 (1998) 185.
[25] Y. Li, J. Wang, Z. Deng, Y. Wu, X. Sun, D. Yu, P.J. Yang, Am. Chem. Soc. 123 [35] T.J. Daou, G. Pourroy, S. Be gin-Colin, J.M. Grene che, C. Ulhaq-Bouillet,
(2001) 9904. P. Legare , P. Bernhardt, C. Leuvrey, G. Rogez, Chem. Mater. 18 (2006) 4399.
[26] H. Liu, J.Y. Wang, X.B. Hu, F. Gu, L. Hua, C.Q. Zhang, B. Tneg, D.L. Cui, J.Q. Pan, [36] F. Jiao, J.-C. Jumas, M. Womes, A.V. Chadwick, A. Harrison, P.G. Bruce, J. Am.
Chem. Mater. 13 (2001) 151. Chem. Soc. 128 (2006) 12905.
[27] H.H. Nersisyan, J.H. Lee, H.T. Son, C.W. Won, D.Y. Maeng, Mater. Res. Bull. 38 [37] S.K. Arora, H.-C. Wu, R.J. Choudhary, I.V. Shvets, O.N. Mryasov, H. Yao,
(2003) 949. W.Y. Ching, Phys. Rev. B 77 (2008) 134443.
[28] Q. Xie, Z. Dai, W. Hyang, J. Liang, C. Jiang, Y. Qian, Nanotechnology 16 (2005) [38] F.C. Voogt, T.M. Palstra, L. Niesen, O.C. Rogojanu, M.A. James, T. Hibma, Phys.
2958. Rev. B 57 (1998) R8107.
[29] S. Park, K. Kang, W. Han, T. Vogt, J. Alloys Compd. 400 (2005) 88. [39] S. Sun, H. Zeng, J. Am. Chem. Soc. 124 (2002) 8204.