JOB NO. ITEM NO.

Brown & Root, Inc. PURCHASE ORDER NO.

SPECIFICATION NO.
CENTRIFUGAL COMPRESSOR REVISION NO. DATE
DATA SHEET (API 617-6TH) PAGE 1 OF 6 BY
U.S. CUSTOMARY UNITS
1 APPLICABLE TO: PROPOSAL PURCHASE AS BUILT

2 FOR UNIT

3 SITE SERIAL NO.

4 SERVICE NO. REQUIRED

5 CONTINUOUS INTERMITTENT STAND BY DRIVER TYPE (3.1.1)

6 MANUFACTURER MODEL DRIVER ITEM NO.

7 NOTE: INFORMATION TO BE COMPLETED: BY PURCHASER BY MANUFACTURER

8 OPERATING CONDITIONS

9 OTHER CONDITIONS (3.1.2)

10 (ALL DATA ON PER UNIT BASIS) NORMAL A B C D E

11

12

13 GAS HANDLED (ALSO SEE PAGE )

14 MMSCFD/SCFM (14.7 PSIA & 60 °F DRY)

15 WEIGHT FLOW, #/MIN (WET) (DRY)

16 INLET CONDITIONS

17 PRESSURE (PSIA)

18 TEMPERATURE (°F)

19 RELATIVE HUMIDITY %

20 MOLECULAR WEIGHT (%)

21 Cp/Cv ( K1 ) OR (KAVG )

22 COMPRESSIBILITY (Z1 ) OR (ZAVG )

23 INLET VOLUME, (CFM) (WET / DRY)

24 DISCHARGE CONDITIONS

25 PRESSURE (PSIA)

26 TEMPERATURE (°F)

27 Cp/Cv (K2 ) OR (KAVG ) (NOTE 1)

28 COMPRESSIBILITY (Z2 ) OR (ZAVG ) (NOTE 1)

29

30 BHP REQUIRED (ALL LOSSES INCLUDED)

31 SPEED (RPM)

32 ESTIMATED SURGE, ICFM (AT SPEED ABOVE)

33 POLYTROPIC HEAD (FT-LBS / LB)

34 POLYTROPIC EFFICIENCY (%)

35 CERTIFIED POINT

36 PERFORMANCE CURVE NUMBER

37 PROCESS CONTROL

38 METHOD SUCTION THROTTLING VARIABLE INLET SPEED VARIATION DISCHARGE COOLED BYPASS

39 FROM PSIA GUIDE VANES FROM % BLOWOFF FROM

40 TO PSIA (3.4.2.4) TO % TO TO

41

42 SIGNAL SOURCE ( 3.4.2.1)

43 TYPE ELECTRONIC PNEUMATIC OTHER

44 RANGE MA PSIG
45

46 ANTI-SURGE BYPASS MANUAL AUTOMATIC NONE

47

48 REMARKS:

49 NOTE 1: IF GAS ANALYSIS IS GIVEN, MANUFACTURER SHALL SUPPLY DATA , OTHERWISE DATA SHALL BE SUPPLIED BY USER.

07/96 EF-050-09.01 SHT 1 OF 6 API617.XLS REV 0

 Brown & Root, Inc.
JOB NO. 0 ITEM NO. 0
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE 0
DATA SHEET (API 617-6TH) PAGE 2 OF 6 BY 0
U.S. CUSTOMARY UNITS
1 OPERATING CONDITIONS (Continued) (3.1.2) (3.1.3)

2 GAS ANALYSIS: OTHER CONDITIONS (2.11.1.3)

3 MOL % NORMAL A B C D E REMARKS: (2.11.1.8)

4 MW

5 AIR 28.966

6 OXYGEN 32.000

7 NITROGEN 28.016

8 WATER VAPOR 18.016

9 CARBON MONOXIDE 28.010

10 CARBON DIOXIDE 44.010

11 HYDROGEN SULFIDE 34.076 (2.11.1.7)

12 HYDROGEN 2.016

13 METHANE 16.042

14 ETHYLENE 28.052

15 ETHANE 30.068

16 PROPYLENE 42.078

17 PROPANE 44.094

18 I-BUTANE 58.120

19 n-BUTANE 58.120

20 I-PENTANE 72.146

21 n-PENTANE 72.146

22 HEXANE PLUS

23

24

25 TOTAL

26 AVG. MOL. WT.

27 LOCATION: (2.1.9) NOISE SPECIFICATIONS: (2.1.10)

28 INDOOR OUTDOOR GRADE APPLICABLE TO MACHINE:

29 HEATED UNDER ROOF MEZZANINE SEE SPECIFICATION

30 UNHEATED PARTIAL SIDES APPLICABLE TO NEIGHBORHOOD:

31 ELEC. AREA CLASSIFICATION (2.1.15) CL GR DIV SEE SPECIFICATION

32 WINTERIZATION REQ'D. (2.1.9) TROPICALIZATION REQ'D. ACOUSTIC HOUSING: YES NO

33 SITE DATA (3.4.6.6)

34 ELEVATION FT BAROMETER PSIA APPLICABLE SPECIFICATIONS:

35 RANGE OF AMBIENT TEMPS: API 617, CENTRIFUGAL COMPR. FOR GEN. REFINERY SERV.

36 DRY BULB WET BULB VENDOR HAVING UNIT RESPONSIBILITY (2.9.1.7)

37 NORMAL °F

38 MAXIMUM °F GOVERING SPECIFICATION (IF DIFFERENT)

39 MINIMUM °F

40 °F

41 UNUSUAL CONDITIONS: DUST FUMES PAINTING:

42 °F MANUFACTURER'S STD.

43 OTHER (2.1.9) OTHER

44
45 SHIPMENT: (4.4.1)

46 REMARKS: DOMESTIC EXPORT EXPORT BOXING REQ'D.

47 OUTDOOR STORAGE MORE THAN 6 MONTHS (4.4.1)

48 SPARE ROTOR ASSEMBLY PACKAGED FOR (4.4.3.10)

49 HORIZONTAL STORAGE VERTICAL STORAGE

07/96 EF-050-09.01 SHT 2 OF 6 API617.XLS REV 0

 Brown & Root, Inc.
JOB NO. 0 ITEM NO. 0
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE 0
DATA SHEET (API 617-6TH) PAGE 3 OF 6 BY 0
U.S. CUSTOMARY UNITS
1 CONSTRUCTION FEATURES

2 SPEEDS: TYPE (OPEN, ENCLOSED, ETC.)

3 MAX. CONT. RPM TRIP RPM TYPE FABRICATION

4 MAX. TIP SPEEDS: FPS @ 100% SPEED MATERIAL

5 FPS @ MAX. CONT. SPEED MAX. YIELD STRENGTH (PSI)

6 LATERAL CRITICAL SPEEDS (DAMPED) BRINNEL HARDNESS: MAX MIN

7 FIRST CRITICAL RPM MODE SMALLEST TIP INTERNAL WIDTH (IN.)

8 SECOND CRITICAL RPM MODE MAX. MACH. NO. @ IMPELLER EYE

9 THIRD CRITICAL RPM MODE MAX. IMPELLER HEAD @ 100% SPD (FT-LBS/LB)

10 FOURTH CRITICAL RPM MODE SHAFT:

11 TRAIN LATERAL ANALYSIS REQUIRED (2.9.2.3) MATERIAL

12 TRAIN TORSIONAL ANALYSIS REQUIRED DIA @ IMPELLERS (IN) DIA @ COUPLING (IN.)

13 (TURBINE DRIVEN TRAIN) (2.9.4.5) SHAFT END: TAPERED CYLINDRICAL

14 TORSIONAL CRITICAL SPEEDS: MAX. YIELD STRENGTH (PSI)

15 FIRST CRITICAL RPM SHAFT HARDNESS (BNH)(Rc)

16 SECOND CRITICAL RPM MAX TORQUE CAPABILITY (FT-LBS)

17 THIRD CRITICAL RPM BALANCE PISTON:

18 FOURTH CRITICAL RPM MATERIAL AREA (IN² )

19 VIBRATION: FIXATION METHOD

20 ALLOWABLE TEST LEVEL MILS SHAFT SLEEVES:

21 (PEAK TO PEAK) AT INTERSTG. CLOSE MATL

22 ROTATION, VIEWED FROM DRIVEN END CW CCW CLEARENCE POINTS

23 MATERIALS INSPECTION REQUIREMENTS (4.2.2) AT SHAFT SEALS MATL

24 SPECIAL CHARPY TESTING (2.11.3) ACCESSIBLE(2.8.2)

25 RADIOGRAPHY REQUIRED FOR LABYRINTHS:

26 ULTRASONIC REQUIRED FOR INTERSTAGE

27 MAGNETIC PARTICLE REQUIRED FOR TYPE MATERIAL

28 LIQUID PENETRANT REQUIRED FOR BALANCE PISTON

29 CASING: TYPE MATERIAL

30 MODEL SHAFT SEALS:

31 CASING SPLIT SEAL TYPE (2.8.3)

32 MATERIAL SETTLING OUT PRESSURE (PSIG)

33 THICKNESS (IN.) CORR. ALLOW. (IN.) SPECIAL OPERATION (2.8.1)

34 MAX. WORKING PRESS PSIG SUPPLEMENTAL DEVICE REQUIRED FOR CONTACT

35 MAX DESIGN PRESS PSIG SEALS (2.8.3.2) TYPE

36 TEST PRESS (PSIG): HELIUM HYDRO BUFFER GAS SYSTEM REQUIRED (2.8.7) MANIFOLD (3.5.1.6)

37 MAX OPER. TEMP. °F MIN. OPER. TEMP. °F TYPE BUFFER GAS

38 MAX NO. OF IMPELLERS FOR CASING BUFFER GAS CONTROL SYSTEM SCHEMATIC BY VENDOR

39 MAX CASING CAPACITY (ICFM) PRESSURIZING GAS FOR SUBATMOSPHERIC SEALS (2.8.8)

40 CASING SPLIT SEALING (2.2.10) TYPE SEAL

41 SYSTEM RELIEF VALVE SET PT. (2.2.4) PSIG INNER OIL LEAKAGE GUAR. (GAL/DAY/SEAL)

42 DIAPHRAGMS: BUFFER GAS REQUIRED FOR:

43 MATERIAL AIR RUN-IN OTHER

44 IMPELLERS: BUFFER GAS FLOW (PER SEAL):

45 NO. DIAMETERS NORM: LBS/MIN @ PSI D P

46 NO. VANES EA. IMPELLER MAX. LBS/MIN @ PSI D P

47 BEARING HOUSING CONSTRUCTION:

48 TYPE (SEPARATE, INTEGRAL) SPLIT

49 MATERIAL

07/96 EF-050-09.01 SHT 3 OF 6 API617.XLS REV 0

 Brown & Root, Inc.
JOB NO. 0 ITEM NO. 0
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE 0
DATA SHEET (API 617-6TH) PAGE 4 OF 6 BY 0
U.S. CUSTOMARY UNITS
1 CONSTRUCTION FEATURES (CONTINUED)

2 BEARINGS AND BEARING HOUSINGS

3 RADIAL INLET EXHAUST THRUST ACTIVE INACTIVE

4 TYPE TYPE

5 MANUFACTURER MANUFACTURER

6 LENGTH (IN.) UNIT LOADING (MAX PSI)

7 SHAFT DIA. (IN.) UNIT LOAD (ULT.) (PSI)

8 UNIT LOAD (ACT/ALLOW) AREA (IN²)

9 BASE MATERIAL NO. PADS

10 BABBIT THICKNESS (IN.) PIVOT: CENTER / OFFSET, %

11 NO. PADS PAD BASE MATL

12 LOAD: B'TWN/ON PAD LUBRICATION: FLOODED DIRECTED

13 PIVOT: CTR/OFFSET, % THRUST COLLAR: INTEGRAL REPLACEABLE

14 MATERIAL

15 BEARING SPAN INCHES

16 BEARING TEMPERATURE DEVICES SEE ATTACHED VIBRATION DETECTORS: SEE ATTACHED API-670 DATA SHEET

17 THERMISTORS API-670 DATA SHT TYPE MODEL

18 TYPE POS TEMP COEFF NEG TEMP COEFF MFR

19 TEMP SWITCH & INDICATOR BY: PURCH MFR NO. AT EA SHAFT BEARING TOTAL NO.

20 THERMOCOUPLES OSCILLATOR-DETECTORS SUPPLIED BY

21 SELECTOR SWITCH & INDIC. BY: PURCH MFR MFR MODEL

22 RESISTANCE TEMP DETECTORS MONITOR SUPPLIED BY (3.4.7.2)

23 RESISTANCE MAT'L OHMS LOCATION ENCLOSURE

24 SELECTOR SWITCH & INDIC. BY: PURCH MFR MFR. MODEL

25 LOCATION-JOURNAL BRG SCALE RGE ALARM SET @ MILS

26 NO. EA PAD EVERY OTH PAD PER BRG SHTDWN: SET @ MILS TIME DELAY SEC

27 OTHER

28 LOCATION-THRUST BRG AXIAL POSITION DETECTOR: SEE ATTACH. API-670

29 NO. EA PAD EVERY OTH PAD PER BRG DATA SHEET

30 OTHER TYPE MODEL

31 NO. (INACT) EA PAD EVERY OTH PAD PER BRG MFR NO. REQUIRED

32 OTHER OSCILLATOR-DEMODULATOR SUPPLIED BY

33 MONITOR SUPPLIED BY (3.4.7.4) MFR MODEL

34 LOCATION ENCLOSURE MONITOR SUPPLIED BY (3.4.7.2)

35 MFR. MODEL LOCATION ENCLOSURE

36 SCALE RGE ALARM SET @ °F MFR. MODEL

37 SHTDWN SET @ °F TIME DELAY SEC SCALE RGE ALARM SET @ MILS

38 SHTDWN: SET @ MILS TIME DELAY SEC

39 CASING CONNECTIONS

40 DESIGN ASME FLANGED MATING FLG GAS

41 APPROVAL API605 POSITION OR & GASKET VELOCITY

42 CONNECTION REQ'D OTHER FACING (2.4.2.1) STUDDED BY VENDOR FT/SEC

43 (2.11.2.10) SIZE (2.4.2.1) (2.4.2.3)

44 INLET

45 DISCHARGE

46

47

48

07/96 EF-050-09.01 SHT 4 OF 6 API 617SI.XLS REV 0

 Brown & Root, Inc.
JOB NO. 0 ITEM NO. 0
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE 0
DATA SHEET (API 617-6TH) PAGE 5 OF 6 BY 0
U.S. CUSTOMARY UNITS
1 OTHER CONNECTIONS ALLOWABLE PIPING FORCES AND MOMENTS:

2 SERVICE: NO. SIZE TYPE INLET DISCHARGE

3 LUBE-OIL INLET FORCE MOMT FORCE MOMT FORCE MOMT

4 LUBE OIL OUTLET LB FT.LB LB FT.LB LB FT.LB

5 SEAL-OIL INLET AXIAL

6 SEAL-OIL OUTLET VERTICAL

7 SEAL GAS INLET HORIZ. 90

8 SEAL GAS OUTLET FORCE MOMT FORCE MOMT FORCE MOMT

9 CASING DRAINS LB FT.LB LB FT.LB LB FT.LB

10 STAGE DRAINS AXIAL

11 VENTS VERTICAL

12 COOLING WATER HORIZ. 90

13 PRESSURE CASING VIBRATION TRANSDUCER (3.4.7.5)

14 TEMPERATURE SEE ATTACHED API-670 DATA SHEET

15 SOLVENT INJECTION TYPE MODEL

16 PURGE FOR: MFR NO. REQUIRED

17 BRG. HOUSING LOCATION

18 BTWN BRG & SEAL OSCILATOR-DEMODULATORS SUPPLIED BY

19 BTWN SEAL & GAS MFR MODEL

20 INDIVIDUAL STAGE DRAINS REQUIRED (2.4.3.2) MONITOR SUPPLIED BY (3.4.7.6)

21 VALVED & BLINDED LOCATION ENCLOSURE

22 VALVED & BLINDED & MANIFOLD MFR MODEL

23 KEY PHASOR REQUIRED SCALE RANGE ALARM SET @ IN/SEC²

24 COMPRESSOR GEAR DRIVER SHTDWN SET @ IN/SEC² TIME DELAY SEC

25 ACCESSORIES

26 COUPLING AND GUARDS (3.2)

27 NOTE: SEE ROTATING ELEMENTS - SHAFT ENDS

28 SEE ATTACHED API-671 DATA SHEET KEYLESS HYDRAULIC KEYED

29 COUPLING FURNISHED BY

30 MANUFACTURER TYPE MODEL

31 COUPLING GUARD FURNISHED BY:

32 TYPE: FULLY ENCLOSED SEMI-OPEN OTHER

33 COUPLING DETAILS

34 MAX O.D. IN. VENDOR MOUNT HALF COUPLING

35 HUB WEIGHT LBS LUBRICATION REQUIREMENTS:

36 SPACER LENGTH IN NON-LUBE GREASE CONT. OIL LUBE OTHER

37 SPACER WEIGHT LBS QUANTITY PER HUB LBS OR GPM

38 MOUNTING PLATES

39 BASEPLATES: FURNISHED BY (3.3.1.1)

40 COMPRESSOR ONLY (3.3.2.1) DRIVER GEAR SOLEPLATES: FURNISHED BY:

41 OTHER THICKNESS IN

42 DRIP TRIM LEVELING PADS (3.3.2.2) SUBSOLE PLATES REQ'D (3.3.3.2)

43 COLUMN MOUNTING (3.3.2.3) LEVELING BLOCKS REQ'D

44 SUB-SOLE PLATES REQ'D (3.3.3.2) STAINLESS STEEL SHIM THICKNESS - INCHES

45 STAINLESS STEEL SHIM THICKNESS INCHES DRIVER GEAR COMPRESSOR

46 PRIMER FOR EPOXY GROUT REQ'D (3.3.1.2.9) PRIMER FOR EPOXY GROUT REQ'D (3.3.1.2.9)

47 TYPE TYPE

48 BASE PLATE WILL BE ON CONCRETE FOUNDATION (3.3.2.5)

49 MACHINED MOUNTING PADS REQ'D. (3.3.2.6)

07/96 EF-050-09.01 SHT 5 OF 6 API617.XLS REV 0

 Brown & Root, Inc.
JOB NO. 0 ITEM NO. 0
CENTRIFUGAL COMPRESSOR REVISION NO. 0 DATE 0
DATA SHEET (API 617-6TH) PAGE 6 OF 6 BY 0
U.S. CUSTOMARY UNITS
1 UTILITIES

2 UTILITY CONDITIONS: TOTAL UTILITY CONSUMPTION:

3 STEAM: DRIVERS HEATING COOLING WATER GPM

4 INLET MIN PSIG °F PSIG °F STEAM, NORMAL LBS/HR

5 NORM PSIG °F PSIG °F STEAM, MAX LBS/HR

6 MAX PSIG °F PSIG °F INSTRUMENT AIR SCFM

7 EXHAUST. MIN PSIG °F PSIG °F HP (DRIVER) HP

8 NORM PSIG °F PSIG °F HP (AUXILIARIES) HP

9 MAX PSIG °F PSIG °F HEATERS KW

10 ELECTRICITY: (3.4.6.1) PURGE (AIR OR N2) SCFM

11 DRIVERS HEATING CONTROL SHUTDOWN

12 VOLTAGE MISCELLANEOUS:

13 HERTZ RECOMMENDED STRAIGHT RUN OF PIPE DIAMETERS

14 PHASE BEFORE SUCTION

15 COOLING WATER: NOMOGRAPHS REQUIRED FOR EACH SELECTION (5.3.3.1.5)

16 TEMP. INLET °F MAX RETURN °F VENDOR'S REVIEW & COMMENTS ON PURCHASER'S

17 PRESS NORM PSIG DESIGN PSIG PIPING & FOUNDATION (3.5.3.2)

18 MIN RETURN PSIG MAX ALLOW D P PSI COMPRESSOR TO BE SUITABLE FOR FIELD RUN IN

19 WATER SOURCE ON AIR (2.1.17)

20 INSTRUMENT AIR: PROVISION FOR LIQUID INJECTION (2.1.11)

21 MAX PRESS PSIG MIN PRESS PSIG VENDOR'S REVIEW & COMMENTS ON PURCHASER'S

22 CONTROL SYSTEMS (3.4.1.1)

23 SHOP INSPECTION AND TESTS: (4.1.4) EXTENT OF PROCESS PIPING BY VENDOR (3.5.3.1)

24 REQ'D SHOP FITUP OF VENDOR PROCESS PIPING (4.4.3.11)

25 CLEANLINES (4.2.1.5) WELDING HARDNESS TESTING (4.2.1.6)

26 HYDROSTATIC X

27 IMPELLER OVERSPEED X VENDOR'S REPRESENTATIVE SHALL (2.1.14)

28 MECHANICAL RUN X OBSERVE FLANGE PARTING

29 CONTRACT COUPLING IDLING ADAPTOR(S) CHECK ALIGNEMENT AT TEMPERATURE

30 CONTRACT PROBES SHOP PROBES BE PRESENT AT INITIAL ALIGNMENT

31 VARY LUBE & SEAL OIL PRESSURES WEIGHTS (LB):

32 AND TEMPERATURES (4.3.4.2.5) COMPR. GEAR DRIVER BASE

33 POLAR FORM VIB DATA (4.3.4.3.3) ROTORS: COMPR. DRIVER GEAR

34 TAPE RECORD VIB DATA (4.3.4.3.6) COMPRESSOR UPPER CASE

35 TAPE DATA TO PURCHASER (4.3.4.3.7) SOUR SEAL OIL TRAPS

36 SHAFT END SEAL INSP (4.3.4.4.1) L.O. CONSOLE S.O. CONSOLE

37 GAS LEAK TEST DISCH PRESS (4.3.5.3) OVERHEAD SEAL OIL TANKS

38 BEFORE AFTER POST TEST INSPECTION (4.3.6.8) MAX. FOR MAINTENANCE (IDENTIFY)

39 PERFORMANCE TEST(GAS)(AIR)(4.3.6.1) TOTAL SHIPPING WEIGHT

40 COMPLETE UNIT TEST (4.3.6.2)

41 TORSIONAL VIB MEAS (4.3.6.2) SPACE REQUIREMENTS (FT & IN.):

42 TANDEM TEST (4.3.6.3) COMPLETE UNIT: L W H

43 GEAR TEST (4.3.6.4) L.O. CONSOLE: L W H

44 HELIUM LEAK TEST (4.3.6.5) S.O. CONSOLE: L W H

45 SOUND LEVEL TEST (4.3.6.6) SOUR SEAL OIL TRAPS

46 FULL LOAD / SPEED / PRESS TEST (4.3.6.9) OVERHEAD SEAL OIL TANKS

47 HYDRAULIC COUPLING INSP (4.3.6.10)

48 REMARKS:

49

07/96 EF-050-09.01 SHT 6 OF 6 API610.XLS REV 0