B.E.

Civil Engineering, VII Sem

COURSE CODE: CE -701 COURSE: IRRIGATION ENGINEERING
Course scheme Evaluation scheme (Theory)
lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 1 - 4 3 3 Hr 10 10 80 100

Unit CONTENTS Hours

I GENERAL: Necessity and importance of Irrigation Engineering, 9
Benefits & effects of Irrigation, Classification of Irrigation, General
principles of flow, lift, perennial, inundation Irrigation systems,
Comparative study of sprinkler and drip Irrigation systems.

WATER REQUIREMENT OF CROPS: Suitability of soils for Irrigation,

Standards of irrigation water, PET-R method of crop water requirements,
Depth and frequency of Irrigation, definitions of field capacity wilting
point, available moisture, duty, delta, GCA, CCA, or depth, base period
outlet factor capacity factor, time factor, root zone depth: Relation
between duty and delta; Factors affecting duty, Principal crops in India,
Crop rotation; Methods of assessment of Irrigation water..
II RESERVOIR PLANNING : Selection of site for Reservoirs; Engineering 9
surveys, Geological and Hydrological Investigations; Fixing of LWL,
FTL, TBL, HFL; Diriment storage zones in reservoir, Determination of
storage capacity by mass curve method; Reservoir sedimentation; Life
estimation of reservoir by Burn‘s method; Organization &
Administration of Irrigation Projects
WATER LOGGING AND LAND DRAINAGE : Causes, effects,
preventive measures of water logging, types of drains, layout of tile
drains systems, flow of ground water to drains.
RIVER TRAINING WORKS : Definition, classification, theoretical
aspects of river training works like as Guide banks, Groynes and Spurs,
Bank protection.
III DAMS 9
Classification of dams as per use, Hydraulic design and materials;
Factors governing selection of type of dams.

GRAVITY DAM: Definition; forces acting on gravity dam; stability

Syllabus – VII sem Civil Engineering/ GU Page 1

 requirements; Theoretical & practical profile of gravity dam; low & High
dam; Galleries.

EARTHEN DAMS: Types of earthen dam; Description of component

part of earthen dams foundation, cut off trench, rock toe, hearting, central
impervious core, pitching and chipping, turfing; seepage through body of
earthen dam and drainage arrangements; Failure of earthen dams;
Plotting of phreatic line for homogeneous earthen dams with horizontal
filters; Stability of foundation against shear.
SPILLWAYS : Types of spillway with their working operations; General
principle of design of ogee spillway; Spillway gates-vertical lift radial,
rolling and drum; Energy dissipation methods d/s of spillways.
IV CANALS: 9
GENERAL: Types of canal; Alignments of canal; Cross section of
Irrigation canals; Blanching depth; Schedule of area statistics; Losses in
canals.
CANALS IN ALLUVIAL SOILS: Kennedy‘s silt theory – Design
procedure ‗ silt supporting capacity, drawbacks; Lacey‘s silt theory –
Definition of initial final and permanent regime channels, Lacey‘s
Regime equation, channel design procedure, drawbacks; Garret‘s
diagram for channel design.
LINED CANALS: Design procedure; Types of lining; relative merits
and demerits of canal lining; Economics of canalling
V CANAL STRUCTURES 9
CANAL REGULATION WORKS: Only theoretical aspects of location,
objects, classification, component and schematic section of head
regulator, cross regulators, canal escapes, canal falls and canal outlets.
CROSS DRAINAGE WORKS Only theoretical aspects of location,
object, classification, components and schematic section of aqueduct,
siphon, super passage, canal siphon, inlets, outlets and level crossings.
DIVERSION HEAD WORKS:Component parts of diversion headwork‘s
– Fish ladder guide wall‘ divide all silt excluder and silt ejector; Causes
of failure of weirs on permeable foundation; Blight‘s creep theory; dr.
Khosla‘s theory for design of weirs on permeable foundation. .

Syllabus – VII sem Civil Engineering/ GU Page 2

Recommended Books:-

1. Irrigation Engineering and Hydraulic Structures- Santosh Kumar Garg- khanna publication

2. Irrigation Engineering and Hydraulic Structures- S. R. Sahastrabudhe- katson publication

3. Irrigation Engineering and Water Power Engineering – B. C. Punmia-laxmi publication

4. Irrigation Engineering and Hydraulic Structures- K. R. Arora- jain year of publication

5. Irrigation Engineering- N. N. Basak- jain year of publication

6. Irrigation Engineering and Hydraulic Structures- R. K. Sharma- S. Chand publication

7. Water Resources and Irrigation Engineering – P. N. Modi

Syllabus – VII sem Civil Engineering/ GU Page 3

Course Code: CE -714 Course: IRRIGATION ENGINEERING PRACTICAL
Course scheme Evaluation scheme (Practical)
lecture Tutorial Practical Periods/week Credits TW POE Total
- - 3 3 2 25 25 50

A. Detailed Design and Drawing on full sheet (A1)should be included (Minimum Five) as
term work.

1. Reservoir Planning – Capacity of reservoir.

2. Life of Reservoir

3. Gravity Dam – Checking of various modes.

4. Earthen Dam – Phreatic Line, Checking of foundation against shear

5. Design of canals (Lined and Unlined)

6. Design of Lift Irrigation Scheme.

7. Drawing of various canal structures.

B. Detailed report of one Site visit to irrigation project in spiral binding form must be
submitted with above five practical.

Syllabus – VII sem Civil Engineering/ GU Page 4

 B.E. Civil Engineering, VII Sem
COURSE CODE: CE -702 COURSE: STRUCTURAL ANALYSIS -III

Course scheme Evaluation scheme (Theory)

lecture Tutorial Practical Periods/week Credits Duration of MSE IE ESE Total
paper hour
4 0 0 4 4 4 10 10 80 100

COURSE OUTCOMES:

The students shall be able to

1. Formulation of stiffness matrix, transformation matrix, load matrix for various

structural components for analysis purposes and understanding of structural
software.
2. Apply the different methods of analysis of frames in practical problems.
3. Understand the concepts related to structural dynamics.
4. Understand the basics of finite element method in the analysis of structural
components.

Unit Topics Hours

I Formulation of element/local stiffness matrix and global (10)

stiffness matrix for beam members (with and without axial
deformation). Continuous beams with/without sinking of
support, Assembly of global/ structural stiffness matrix,
Member load matrix due to concentrated load, uniformly
distributed Load varying load and moment. Assembly of
global/ structure load matrix up to Three Elements. Solution
to problems with maximum degree of freedom Three and
formulation of stiffness matrix upto DOF 6.
II Formulation of element/ local stiffness matrix and global (12)
stiffness matrix for Plane frame members (with and without
axial deformation), Transformation matrix, Assembly of
global/ structural stiffness matrix, Member load matrix due to
concentrated loads, uniformly distributed Loads, varying load,
Moments. Assembly of global/ structural load matrix. Plane
frame problems with maximum degree of freedom six and
Solution to problems with maximum degree of freedom
Three. Inclined member problems, Analysis of plane frame
upto 3 DOF with support displacement.

Syllabus – VII sem Civil Engineering/ GU Page 5

 III Basic concept, Degree of Freedom, Basic concept of Direct (12)
Stiffness Method. Formulation of elemental/local stiffness
matrix and global stiffness matrix for plane truss.
Transformation Matrix, Assembly of Global/ Structural
stiffness matrix up to (8x8). Member load matrix including lack
of fit, Support displacement and temperature. Assembly of
Global/ Structure load matrix, Solution to problems with
maximum degree of freedom four.
IV Introduction to structural dynamics, D'Alembert principle, (8)
inertia force, equation of motion (free vibration), SDOF
system, Damping, natural frequency.
MDOF, vibrations of undamped systems up to 2 DOF.
V Introduction to finite Element method, basic concepts, (8)
discretization of structures, Minimum potential energy
theorem and Rayleigh Ritz method for bar elements
(prismatic/Non-prismatic), Displacement based bar elements
(Prismatic/Non-prismatic).
Storage techniques, Half band storage, half band width, Sky
line storage.

REFERENCE BOOKS:
1. Gere and Weaver, Matrix Method of Structural Analysis, Third Edition, Von
Nostrand Reinhold; New York 1990.
2. Meghre A. S. and Deshmukh S. K., Matrix Method of Structural Analysis, First
Edition, Charotar Publishing House, Anand 2003.
3. Chandrupatala T.R., Belegundu A. D., Introduction to Finite Element in
Engineering, Prentice Hall India, 1991.
4. Chopra A. K., Dynamics of Structure, Theory and Application of Earthquake
Engineering, Third Edition, Pearson.
5. Krishnamurthy C. S., Finite Element Method, TATA McGRAW HILL.

Syllabus – VII sem Civil Engineering/ GU Page 6

 B.E. Civil Engineering, VII Sem
COURSE CODE: CE -703 COURSE: Design of RCC structure II

Course scheme Evaluation scheme (Theory)

lecture Tutorial Practical Periods/week Credits Duration of MSE IE ESE Total
paper hour
3 1 0 4 4 10 10 80 100

UNIT TOPICS HOURS

I Limit state of collapse in flexure : Analysis and design of doubly (9)
reinforced rectangular, Tee and L-sections.
Limit state of collapse in torsion: Concept of interaction of torsion ,
shear and flexure . Analysis and design of rectangular section for
torsion , shear and flexure.
Limit state of serviceability: Deflection calculations for beams and one
way slabs.
II Analysis and design of columns subjected to biaxial moments . Design (9)
of long columns. Design of long columns. Design of isolated footing,
for uniaxial and biaxial bending, for square , rectangular and circular.

III Moment redistribution Analysis and Design of Fixed beam , propped (9)
Cantilever , two –span Symmetric continuous beam.
IV ( with LSM) Analysis and design of portal frames ( single bay single (9)
storey) hinged or fixed at base. Design of hinge and design of
foundation. Design of combined footing 1) rectangular footing 2) strap
beam footing 3)Trapezoidal footing . 4) Raft footing.
V ( with LSM) Design of RCC Two way slab with various end (9)
conditions using with is code coefficient. Design of RCC Cantilever
and Counter fort Retaining wall.

Recommended books:

1. Reinforced Concrete Structures, Volume 2 ,Dr. B. C. Punmia, Ashok Kr. Jain,

Arun Kr. Jain, Dr. B.C. Punmia, Ashok Kr. Jain, Arun Kr. Jain-Firewall Media
2. Reinforced Concrete Design, (3rd edition) by Unni Krishna Pillai S. and Devdas
Menon, Tata McGraw-Hill, 2012.
3. Reinforced Concrete (Limit State Method) Ashok Jain K., Nemchand & Bros.,
Roorkee, 2007.
4. Limit State theory and Design of reinforced concrete by Karve, S. R. and Dr. Shah
V. L., Pune Vidyarthi Griha Prakasan, Pune, 2012.
5. Limit State Design of Foundations, (2nd edition) by Varghese P.C., PHI Learning
Pvt. Ltd., New Delhi., 2008.

Syllabus – VII sem Civil Engineering/ GU Page 7

 6. Advanced design of R.C. Structures, (2nd edition) by Bhavikatti S.S., 2009.
7. Design of concrete structures, (13th edition) by Arther Nilson H., Tata Mc Graw-
Hill, 2010. Web Reference books: NPTEL
8. IS CODE: IS 456 – 2000 and 15875-1987 is permitted in the examination.
Question Paper Pattern – 1) One question of 13 Marks each from Unit I,II & III
2) One question of 20 Marks each from Unit V & VI

COURSE CODE: 715 COURSE: DESIGN OF RCC STRUCTURE II (PRACTICAL)

Course scheme Evaluation scheme (LABORATORY)

Lecture Tutorial Practical Credits TW POE Total
3 2 25 25 50

LIST OF EXPERIMENTS

1. Minimum three designs on above syllabus and drawing on A 1 Size drawing sheet.

Syllabus – VII sem Civil Engineering/ GU Page 8

 Elective I - B.E. Civil Engineering, VII Sem
COURSE CODE: CE -704 COURSE: FINITE ELEMENT METHODS
Course scheme Evaluation scheme (Theory)
lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 1 - 4 3 3 Hr 10 10 80 100

Unit CONTENTS Hours

I Introduction to Finite Element Analysis: Introduction , Basic Concepts 7
of Finite Element Analysis , Introduction to Elasticity ,Steps in Finite
Element Analysis.
II Finite Element Formulation Techniques: Virtual Work and 8
Variational principle, Galerkin Method, Finite Element Method:
Displacement Approach,
Stiffness Matrix and Boundary Conditions.
III Element Properties: Natural Coordinates,Triangular Elements 10
,Rectangular Elements, Lagrange and Serendipity Elements , Solid
Elements ,Isoparametric Formulation, Stiffness Matrix of Isoparametric
Elements , Numerical Integration: One Dimensional , Numerical
Integration: Two and Three Dimensional, Worked out Examples
IV Analysis of Frame Structures: Stiffness of Truss Members , Analysis 10
of Truss, Stiffness of Beam Members, Finite Element Analysis of
Continuous Beam, Plane Frame Analysis, Analysis of Grid and Space
Frame.
V FEM for Two and Three Dimensional Solids: Constant Strain Triangle 10
, Linear Strain Triangle , Rectangular Elements, Numerical Evaluation
of Element Stiffness, Computation of Stresses, Geometric Nonlinearity
and Static Condensation , Axisymmetric Element , Finite Element
Formulation of Axisymmetric Element, Finite Element Formulation for 3
Dimensional Elements, Worked out Examples.

Syllabus – VII sem Civil Engineering/ GU Page 9

 REFERENCES:
 C. S. Krishnamoorty, Finite Element Analysis, Tata McGraw-Hill

 David V. Hutton, Fundamentals of Finite Element Analysis, McGraw Hill

 D. Maity, Computer Analysis of Framed Structures, I. K. International Pvt. Ltd. New

Delhi

 Erik G. Thompson, Introduction to the Finite Element Method: Theory, Programming

and Applications, John Wiley

 H. C. Martin and G. F. Carey, Introduction to Finite Element Analysis - Theory and

Application,NewYork, McGraw-Hill

 Irving H. Shames, Clive L. Dym, Energy and Finite Element Methods in Structural

Mechanics;New Age International

 K. J. Bathe, Finite Element Procedures, Prentice-Hall of India, New Delhi, India

 M. Mukhopadhyay, Matrix, Finite Element, Computer and Structural

Analysis, Oxford and IBH Publishing Co. Pvt. Ltd., New Delhi, India

 O. C. Zienkiewicz and Y. K. Cheung, The Finite Element Method in Structural and

Soild Mechanics, McGraw Hill, London

 P. E. Ceruzzi, A History of Modern Computing, The MIT Press, Cambridge, MA,

1998.

Syllabus – VII sem Civil Engineering/ GU Page 10

 ELECTIVE I -B.E. Civil Engineering-VII Sem

Course Code: CE - 705 Course: AIR POLLUTION AND SOLID WASTE MANAGEMENT

Course scheme Evaluation scheme (Theory)

lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 01 - 04 03 4 Hr 10 10 80 100

UNIT TOPICS HOURS

Introduction to air pollution, air pollution episodes, atmosphere and
its zone, classification of air pollutants with their sources, effects of
I 7
air pollutants on man, animals, plants and materials.

Meteorological parameters affecting air pollution, lapse rate and

atmospheric stability, plume behavior, wind rose, pollution rose,
estimation of stack height, greenhouse effect, atmospheric ozone
II depletion. 10
Ambient air sampling, stack sampling, collection of particulate and
gaseous pollutants, methods of estimation.

Air pollution control: Principles of control methods for particulates

and gaseous pollutants control of air pollutants by using various
equipments.
III Automobile exhaust: pollutions due to diesel and petrol engines 8
exhaust treatment and abatement.
Noise pollution: Sources, ill effects, control measures.

Introduction to solid waste management. Classification, sources,

components, quantity and per capita contribution of solid waste.
Physical and chemical characteristics, sampling and analysis of
solid waste.
Collection and transportation of solid waste: methods of collection,
IV 10
equipments used for collection and transportation of solid waste.
Transfer stations and its economic use.
Solid waste processing: methods of processing, choice of methods,
merits and demerits of various methods.

Solid waste disposal by composting: Principles, methods of

composting, factors affecting composting.
Solid waste disposal by sanitary land filling: site requirement,
10
V methods, leachate management.
Solid waste disposal by incineration: Principles, types, merits and
demerits.

Syllabus – VII sem Civil Engineering/ GU Page 11

Books:.

1. Air pollution by M. N. Rao and H. V. N. Rao, (Tata McGraw Hill publications)

2. Environmental Pollution Control Engineering by C. S. Rao, (Wiley Estern Ltd.)
3. Solid waste management in developing countries by A.D. Shinde and B.B. Sundersan
( INSDOC,NewDelhi)
4. Air Pollution, NEERI Manual

Syllabus – VII sem Civil Engineering/ GU Page 12

 Elective I- B.E. Civil Engineering, VIIth Sem
COURSE CODE: CE -706 COURSE: TRAFFIC ENGINEERING
Course scheme Evaluation scheme (Theory)
lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 1 - 4 4 3 Hr 10 10 80 100

Unit CONTENTS Hours

I Traffic Engineering & Studies: Definition, Scope, Various organization 7
working in traffic research, Elements of traffic , characteristics of
vehicle, road user and road; traffic studies-speed & delay, traffic volume,
O & D, parking and accidents, sample size, study methodology, data
collection & presentation,

II Traffic Control & Safety and Enforcement & Education: Traffic signs, 9
road markings, traffic signals-design of signalized intersections and
signaling systems, conflict points, traffic manoeuvres, different
intersections, queuing Theory, Traffic control aids, and street furniture.
Driver error, vehicle & road surface. Traffic accident scenario in India.
Collection and interpretation of accident data and recording in Std. forms
skidding, speed and weather effects on accidents, Analysis of Accidents,
Pedestration cyclists & auto vehicle drivers safety. Traffic 3R and 5E‘s
of traffic management. Motor Vehicle act and Rules, Education, Need
and Methods, Air pollution & Noise Pollution by Traffic, Pollution
standards for auto vehicles, PUC
III Traffic Capacity analysis : Speed, volume, parking & accident data 11
analysis, statistical approach, , , traffic stream characteristics-
relationship between speed, flow and density, level of service & capacity
analysis, traffic forecasting.
IV Traffic Design: Channelisation of islands for different traffic situations, 8
design of rotaries & at-grade intersections, grade separated intersections,
their warrants; facilities for pedestrian & bicycle ways, bus stop location
and bus bay design, transport terminals, parking parcels, design of road
lighting at different road sections & intersections.

V Traffic Control Devices: Traffic signs, markings and signals; principles 10

of signal design, Webster's method, signal coordination.
Traffic Regulation & Management: Speed, vehicle, parking, enforcement
regulations, mixed traffic regulation, management techniques-one-way,
tidal flow, turning restrictions etc., road safety measures Traffic Flow
theory Introduction

Syllabus – VII sem Civil Engineering/ GU Page 13

Recommended Books:
1. Traffic and Highway Engineering, Author Garber N.J. & Lester A. Hoel Publisher West
Publishing Co. New York.
2. Traffic Engineering, Author Roger P. Roess, Elena S. Prassas & William R. Mcshane
Publisher John Willey & Sons.
3. Decision Making on Mega Project: Cost Benefit Analysis, Planning and Innovation
(Transport Economics, Management and Policies), Author Priemm H., Bentt F. & Bert Van
Bee Publisher Edward Elgar Publishing Limited
4. An Introduction to Transportation Engineering, Author William W. Hay Publisher John
Willey & Sons
5. Fundamentals of Transportation Engineering, Robert G. Hennes and Martin Eske Publisher
McGraw Hill Book Co. New York
6. Fundamentals of traffic Engineering , Norman Kennedy Publisher Institute of
Transportation and Traffic Engineering, University of California
7. Traffic Flow Theory and Control, Donald R. Drew Publisher Institute of Transportation
and Traffic Engineering, University of California
8. Highway Engineering, Justo and Khanna.

Syllabus – VII sem Civil Engineering/ GU Page 14

 Elective I- B.E. Civil Engineering, VIIth Sem
COURSE CODE: CE -707 COURSE: River Engineering
Course scheme Evaluation scheme (Theory)
lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 1 - 4 3 3 Hr 10 10 80 100

Unit CONTENTS Hours

I ORIGIN AND PROPERTIES OF SEDIMENTS: 9
Nature of sediment problems, origin and formation of sediments,
properties of sediments , incipient motion of sediment particles , tractive
force approach, cohesive materials.

II REGIMES OF FLOW: 9
Description of regimes of flow, ripple, dune, antidune , prediction of
regimes of flow. Resistance to flow & velocity distribution in alluvial
streams: velocity distribution in turbulent flow over rough boundaries,
resistance and velocity distribution in alluvial streams.
III BED LOAD TRANSPORT & SALTATION: 9
Bed load equations, bed load equations based upon dimensional
considerations and semi-theoretical equations, general comments on bed
load equations, saltation..

IV SUSPENDED LOAD TRANSPORT : 9

Mechanism of suspension, equation of diffusion, sediment distribution
equation , relations for suspended load, wash load , transport of
suspended sediment.

V TOTAL LOAD TRANSPORT : 9

sediment samplers design of canals carrying sediment laiden water Types
of sediment samplers Design of channels carrying sediment laiden water
Sediment transport through pipes

REFERENCES:
1. L Chang H.H.,Fluvial Processes in River Engineering, John Wiley 1988.
2. Simons D.B. and Senturk F., Sediment Transport Technology, Water Resources
Publications, Fort Collins, Colorado, 1977
3. Garde R J and Ranga Raju K G, Fundamentals Mechanics of Sediment Transportation and
Alluvial Stream Problems, Wiley Eastern Ltd 1985.
4. Yang C.T., Sediment Transport- Theory and Practice, The McGraw Hill Companies Inc
,1996.

Syllabus – VII sem Civil Engineering/ GU Page 15

 Elective I- B.E. Civil Engineering, VIIth Sem
COURSE CODE: CE -708 COURSE: GROUND IMPROVEMENT TECHNIQUES
Course scheme Evaluation scheme (Theory)
lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 1 - 4 3 3 Hr 10 10 80 100

Unit CONTENTS Hours

I INTRODUCTION AND CONCEPTS: 9
Different types of problematic soils, their geological formations,
selection of ground improvement techniques based on soil conditions,
objectives of ground improvement techniques, diff. types of
stabilizations. DRAINAGE & DEWATERING- Well point system,
vaccum dewatering system, Deep well drainage, electro-osmosis.
II TREATMENT OF LOOSE SAND- 9
Compaction pile,vibroflotation, dynamic Compaction.
TREATMENT OF EXPANSIVE SOIL- Lime & cement stabilization,
chemical Analysis.
TREATMENT OF SOFT CLAY SOILS- Sand drains & its design
criteria, Stone columns, preloading & surcharge fill dynamic
consolidation.
III GROUTING TECHNIQUES & MATERIALS – 9
Permeation grouting, jet grouting, grouting equipments, diff. types of
grouting materials Bentonite- cement mixes, asphalt etc., grout
monitoring system, grouting in different conditions.
IV GEOSYNTHESITIC APPLICATIONS- 9
Geotextiles& geomembanes, reinforced soil structures, base isolations,
temporary supporting systems etc.
V GROUND IMPROVEMENT FOR SLOPES- 9
Soil nailing, anchoring, prestessed anchors, design methods &
construction techniques.
CASE STUDIES- Case studies of different ground improvement project
in India.

REFERENCES:
1. Dr.B.C.Punmia- Soil Mechanics & Foundation- Laxmi Publication Pvt. Ltd. Delhi.
2. Dr.K.R.Arora-Soil Mechanics & Foundation Engineering-Standard Publisher
Distributor Delhi.
3. Hausmann H.R.- Principles of ground modification- Mcgraw Hill book co.
4. Shashi K.Gulati & Manoj Dutt- Geotechnical Engg- Tata Mcgraw Hill Education
pvt.ltd. New Delhi.
5. Koemer R.M.- Construction & geotechnical methods in foundation Engineering- Tata
Mcgraw Hill New Delhi.
6. P. Purushottam Raj-Ground improvement techniques- Laxmi Publication Pvt. Ltd.
Delhi.

Syllabus – VII sem Civil Engineering/ GU Page 16

 Elective II- B.E. Civil Engineering, VIIth Sem
COURSE CODE: CE -709 COURSE: ADVANCED RCC DESIGN
Course scheme Evaluation scheme (Theory)
lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 1 - 4 3 3 Hr 10 10 80 100

Unit CONTENTS Hours

I Analysis and design of Multistoried buildings up to three bays, calculation of 9
loads, Approximate analysis, Preliminary sizing, IS:875, IS:1893
recommendations, Ductile detailing.
II Analysis and Design of Elevated service Reservoirs, IS Recommendations for 9
wind & earthquake, Ductile detailing.
III Analysis and Design of bridges and Culverts. IRC Recommendations. 9
IV Analysis and design of Silos and Bunkers. IS recommendations. 9
V Analysis and Design of raft foundations, Pile foundations, single pile, group of 9
piles, Pile cap.

REFERENCES:
1. Bhavikatti S. S., Advanced R. C. C. Design Volume-I & II, New age international
publisher, New Delhi.
2. Krishna Raju N, Advanced R. C. C. Design, CSB Publisher and Distributor, New Delhi.
3. B.C. Punmia, Ashok K. Jain, Arun K. Jain – Reinforced Concrete Structures Vol. II, Laxmi
Publications, New Delhi
4. N.C. Sinha, S.K. Roy – Fundamentals of Reinforced Concrete, S. Chand & Co. Ltd, New
Delhi
5. P.C. Varghese – Advanced Reinforced Concrete Design, Prentice Hall of India Pvt. Ltd.,
New Delhi.
6. P. C. Varghese, Design of Reinforced concrete Foundation. PHI Learning Pvt. Ltd.
7. Ramachandra, Design of Concrete Structures Vol. I & II. Standard Book House.
8. Reinforced Concrete design ---Dr.H.J.Shah—Charotar publishing house
9. Design of R.C.C—S.Ramaamruthum -- Dhanpat Rai publications
10. Ramakrishnan and P.D.Arthur, ―Ultimate Strength design for structural concrete‖,
Wheeler Publishing Co.
11. Karve S.R. and Shah V.C, ―Design of reinforced cement concrete structures using Limit
State Approach‖, Structures Publishers.

Syllabus – VII sem Civil Engineering/ GU Page 17

12. Jain O.P and Jaikrishna, ―Plain and reinforced concrete‖, Vol-II, Nemchand and Bros
13. IS: 456-2000 Indian Standard code of practice for plain and reinforced concrete, Bureau of 24/44
Indian Standards, New Delhi.

14. IS: 1893:-2002 Indian Standard Code of practice for criteria for Earthquake resistant design of
Structures, Bureau of Indian Standards, New Delhi.

15. IS: 3370-Indian Standard code of practice for concrete structures for storage of liquids, Bureau of
Indian Standards, New Delhi

Syllabus – VII sem Civil Engineering/ GU Page 18

 Elective II- B.E. Civil Engineering, VIIth Sem
COURSE CODE: CE -710 COURSE: REMOTE SENSING & GIS
Course scheme Evaluation scheme (Theory)
lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 1 - 4 3 3 Hr 10 10 80 100

Unit CONTENTS Hours

I INTRODUCTION AND CONCEPTS: 9
Introduction of Remote Sensing –Definition, stages of remote sensing, Energy
sources and Radiation principles, Energy equation, EMR and Spectrum, EMR
interaction with Atmosphere scattering, Absorption, EMR interaction with earth
surface features reflection, absorption, emission and transmission, Spectral
response pattern , vegetation, soil, water bodies- Spectral reflectance. Active,
Passive, Optical Remote sensing, visible, infrared, thermal, sensors and
characters. Ideal remote sensing system – Characters of real and successful
remote sensing system.
II AERIAL PHOTOGRAPHY AND PHOTOGRAMMETRY 9
Introduction-Terrestrial and Aerial photographs, vertical and oblique
photographs, height determination contouring, photographic interpretations,
stereoscopy, parallax bar, Flight Planning, Photo Interpretation, Applications of
aerial Photos.
III SATELLITE REMOTE SENSING PRINCIPLES AND IMAGE 9
ACQUISITION AND DATA FORMAT:
Data acquisition–Procedure, Reflectance and Digital numbers- Intensity,
Reference data, Ground truth, Analog to digital conversion, Detector
mechanism, Spectro- radiometer. Platforms and sensors- orbits types –
Resolution. Satellite data acquisition, DN characters-kernels- storage devices,
CC, CDisk, Optical disk. Data retrieval. Export and import, Data formats, BSQ,
BIL, BIP, Run length encoding, Image Compression Data products.
IV REMOTE SENSING SATELLITES: 9
Land observation satellites, characters and applications, IRS series, LANDSAT
series, SPOT series, High resolution satellites, character and applications,
CARTOSAT series, IKONOS Series, QUICKBIRD series,
Weather/Meteorological satellites, INSAT series, NOAA, GOES, NIMBUS
Applications, Marine observation satellites OCEANSAT. Microwave remote
sensing Sensors, Concept of Microwave remote sensing, SLAR, SAR
Scattrometers, Altimeter, Characteristics, Image interpretation characters.

Syllabus – VII sem Civil Engineering/ GU Page 19

 V BASICS OF GIS 9
Introduction, concepts , Information system , components of GIS, History,
Geospatial data architecture, Operations, Geographic co ordinate systems, Map
projections, concepts, Input data for GIS , display ,types of output products. GIS
categories, Level and scale of Measurement, importance of data quality.

REFERENCES:
1. A.M. Chandra and S.K. Gosh, Remote Sensing and GIS, Narosa Publishing Home, New
Delhi 2009.
2. Burrogh P.A., Principles of Geographical Information System, Oxford Publications, 1986.
3. George Joseph, Fundamentals of Remote Sensing Universities Press, Hyderabad 2005.
4. Kang tsung Chang, Introduction to Geographical Information System, Tata McGraw Hill,
7th edition, 2010.
5. M. Anji Reddy, Textbook of Remote Sensing and Geographical Information systems, BS
Publications, Hyderabad. 2011.
6. Thomas M. Lillesand, Ralph W. Kiefer, Jonathan W. Chipman Remote sensing and image
interpretation John Wiley & Sons, 2008.

Syllabus – VII sem Civil Engineering/ GU Page 20

 Elective II- B.E. Civil Engineering, VII Sem
COURSE CODE: CE - 711 COURSE:ADVANCED SOIL MECHANICS
Course scheme Evaluation scheme (Theory)
lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 1 - 4 3 3 Hr 10 10 80 100

Unit CONTENTS Hours

I Clay minerology : Concept of composition classification and nomenclature, 7
structure of clay minerals, Kaolinite Illite, Montmorillonite groups physical
properties, clay water relation thixotrophy electrical effects, electrosmossis,
streaming potential Zeta potential.
Drainage and Dewatering : Various systems of and there Graded filters and
design Criteria applications of Geomembranes
II Expansive Soils : Identification and classification Measurement of swelling 9
pressure (vertical) and potential Foundation problems, different types of
foundation design principles Latest technique to tackle expansive nature.
III Compaction & field compaction and controls : Mechanics, Lab & Fd. Tests, Fd. 11
Compaction equipments & these choice and suitability, quality control, Deep
compaction, Vibro floatation.
IV Consolidation : Terxaghi‘s theory for two & three dimensional consolidation 8
field and laboratory tests. Consolidation settlements and drains.
V Soil stabilization, Mechanical and Chemical stabilization, Lab. & 10
Investigations, Field Techniques, Advanced Techniques in Geotextile 89
applications, Stone columns and Gabions.
Case studies of Applications
Recommended Books:
1.Soil Mechanics in Theory & Practice, Author Alam Singh, Publisher Asia Publishing House Edition
1975 & later
2. Geotechnical Engineering Author S. K. Gulhati & Manoj Dutta Publisher Tata McGraw-Hill
Edition 2005
3. Geotechnical Engineering Author Purushothama Raj Publisher Tata McGraw Hill Publishing Co.
Ltd. Edition 1995
4. Soil Mechanics & Foundation Engg Author Punmia B.C. Publisher Laxmi Publication Pvt. Ltd,
New Delhi, Edition 1994
5. Geotechnical Engineering Author C. Venkatramaiah Publisher New Age International Ltd. Edition
(Second Edition) 1995
6. Basic & Applied Soil Mechanics Author Gopal Ranjan & A.S. RAO;, Publisher New Age
InternationalLtd, Edition 2004.

Syllabus – VII sem Civil Engineering/ GU Page 21

 Elective II- B.E. Civil Engineering, VIIth Sem
COURSE CODE: CE -712 COURSE: Advanced Hydraulic Structures
Course scheme Evaluation scheme (Theory)
lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 1 - 4 3 3 Hr 10 10 80 100

Unit CONTENTS Hours

I DESIGN OF WEIRS AND BARRAGES OVER PERMEABLE 9
FOUNDATIONS :
Causes of failure, Bligh‘s and Lane‘s creep theory, Khosla‘s theory and method
of independent variables, standard profiles, corrections, exit gradient, plotting of
HGL, Design of d/s and u/s protection works, length of pucca concrete floor

II SPILLWAYS : Necessity, components and classification, Estimation of 9

spillway design flood, Energy dissipators and its applications
CANAL FALLS : Types and design principles
III CANAL REGULATION WORKS : 9
Alignment of offtaking channels, Distributaries, head regulator, cross regulator
and their design, weir type and regulator type escapes, metering flumes, types of
modules, Kennedy‘s gauge outlet
IV DESIGN CONSIDERATIONS FOR CROSS DRAINAGE WORKS : 9
Fluming the canal, Hind‘s method for design of transition, Design of pucca
canal trough

V HYDRAULICS OF OUTLET WORKS : 9

Sluiceways, river intakes, simple submerged intakes, trash racks Preliminary
concepts of design of stepped spillways and labyrinth weirs

REFERENCES:
1. Garg Santosh Kumar., Irrigation Engineering and Hydraulic Structures, John Khanna Publishers,
New Delhi 2004.
2 Punmia B.C. and Pande B.B. Lal Irrigation and Water Power Engineering, Laxmi Publications Pvt.
Ltd 2003
3. Design of Small Dams, U.S. Bureau Reclamation, Oxford and IBH Publication Co., New Delhi
1960

Syllabus – VII sem Civil Engineering/ GU Page 22

 Elective II- B.E. Civil Engineering, VIIth Sem
Course Code: CE -713 Course: Advanced Prestressed concrete
Course scheme Evaluation scheme (Theory)
lecture Tutorial Practical Periods/week Credits Duration MSE IE ESE Total
of paper
hour
3 1 - 4 3 3 Hr 10 10 80 100

Unit Contents Hours

I Introduction, Prestressing Systems and Material Properties . Basic concepts of 9
pre-stressing; Historical development; Advantages and Types of Prestressing.
Pre-tensioning Systems and Devices, Post-tensioning Systems and Devices,
Need for High strength steel and High strength concrete; Losses Of Prestress:
Nature of losses of pre-stress; Loss due to elastic deformation of concrete,
shrinkage of concrete, creep of concrete, relaxation of stress in steel, friction
and anchorage slip; Total losses allowed for in design.
II Analysis of Prestressed Member. Analysis of Members under Axial Load: 9
Analysis at Transfer, Analysis at Service, Analysis for Ultimate Strength,
Analysis of Member under Flexure:, Analysis at Transfer and at Service,
Cracking Moment, Kern Point, Pressure Line, Analysis for Ultimate Strength,
design loads and strength, Calculation of Crack Width, Variation of Stress in
Steel, Analysis of a Rectangular Section, Analysis of a Flanged Section.
III Deflections of Prestressed Concrete Members . Importance of control of 9
deflections; Factors influencing deflections; Short term deflections of uncracked
members. Long term deflection of cracked member; Transmission Of Pre-
Stress: Transmission of Pre-stressing force by bond; Transmission length; Bond
stresses; Transverse tensile stresses; End zone reinforcement; Flexural bond
stresses in pre –tensioned and post –tensioned grouted beams, stress distribution
in end block, Anchorage zone reinforcements. Shear And Torsion Resistance Of
Prestressed Concrete Member. Shear and Principal stresses; Ultimate shear
resistance of pre-stressed concrete members; Design of shear reinforcement,
pre-stressed concrete members in torsion, Design of reinforcements for torsion,
shear and bending.
IV Design of Pre-Stressed Members 9
Design of sections for flexure, Design of Sections for Axial Tension, Design of
Sections for compression and bending, design of pre-stressed section for shear
and torsion, design of prestressed member for bond. Dimensioning of flexural
member, design for pre-tensioning member, design of post-tensioning
members.

Syllabus – VII sem Civil Engineering/ GU Page 23

 V Composite Construction of Prestressed Concrete. 9
Composite structural member, types of composite construction, analysis of
stresses, differential shrinkages, deflection of composite member, flexural
strength of composite sections, shear strength of composite section.
Design of Continuous Prestressed Concrete Member. Advantages of continuous
members, ultimate load analysis of continuous pre-stressed member, design of
continuous pre-stressed concrete beams.

REFERENCES:
1. Prestressed Concrete by N. Krishna Raju; Tata Mc Graw -Hill Publishing Company Limited, New
Delhi.3rd edition, 1995.

2. Design of Prestressed Concrete Structures by T.Y. Lin & Ned H. Burns; John Wiley & Sons, 3rd
edition, 1981.

Syllabus – VII sem Civil Engineering/ GU Page 24

 Elective II- B.E. Civil Engineering, VII Sem
Course Code: CE -716 COURSE: ADVANCED RCC DESIGN( PRACTICAL)
Course scheme Evaluation scheme (Practical)
lecture Tutorial Practical Periods/week Credits TW POE Total
- - 3 3 2 25 25 50

Any three detailed design and drawing from above five units.
Minimum three design assignments based on theory syllabus along with the detailed
structural drawings on A1size sheets.

Practical Examination shall be based on the above Practical work.

Syllabus – VII sem Civil Engineering/ GU Page 25

 Elective II- B.E. Civil Engineering, VII Sem
Course Code: CE -717 Course: REMOTE SENSING & GIS PRACTICAL
Course scheme Evaluation scheme (Practical)
lecture Tutorial Practical Periods/week Credits TW POE Total
- - 3 3 2 25 25 50

Any ten from the following practical to be performed:

1. Testing stereo vision.
2. Use of Lens stereoscope and Mirror stereoscope.
3. Determination of vertical exaggeration.
4. Use of Parallax Bar for height calculation from aerial photographs.
5. Calculation of scale of the photographs.
6. Marking Principal point and conjugate principal point on the stereo pairs.
7. Study of Image analysis software.
8. Study of GIS software.
9. Creating and editing a shape file from Microsoft Excel file.
10. Spatial analysis with raster data.
11. Geometric correction of raw images.
12. Mosaic of images.
13. Subset creation using ERDAS.
14. Unsupervised classification of Images.
15. Supervised classification of images.
16. GCP collection using GPS.

Syllabus – VII sem Civil Engineering/ GU Page 26

 Elective II- B.E. Civil Engineering, VII Sem
COURSE CODE: CE - 718 COURSE: ADVANCED SOIL MECHANICS
Course scheme Evaluation scheme (Theory)
Practical Periods/week Credits Term work POE Total
3 3 2 25 25 50

Any five practical to be performed

1. Particle size analysis by
i. Hydrometer method
ii. Pipette method
2. Determination of free swell value and differential swell value of a given soil.
3. Determination of swelling pressure of soil.
4. Determination of compaction characteristics of soil by modified Proctor test.
5. Determination of pre-consolidation pressure of soil.
6. Determination of Co-efficient of consolidation of given soil.
7. Chemical stabilization
i. Soil with cement
ii. Soil with lime.
iii. Soil with lime plus flyash.
8. Mechanical stabilization- blending of soil.
9. Case study(any one).

Syllabus – VII sem Civil Engineering/ GU Page 27

 Elective II- B.E. Civil Engineering, VII Sem
Course Code: CE -719 Course: Design of Hydraulic Structures
Course scheme Evaluation scheme (Practical)
Lecture Tutorial Practical Periods/week Credits TW POE Total
- - 3 3 2 25 25 25

Any Three from the following practical to be performed:

1. Analysis, Design and Drawing of Spillways with All details
2. Analysis, Design and Drawing of Weir with All details
3. Analysis, Design and Drawing of Barrage with All details
4. Analysis, Design and Drawing of Canal Fall with All details
5. Analysis, Design and Drawing of Canal Regulation Work with All details

Syllabus – VII sem Civil Engineering/ GU Page 28

 Elective II- B.E. Civil Engineering, VII Sem
Course Code: CE -720 Course: Advance Prestressed Concrete
Course scheme Evaluation scheme (Practical)
lecture Tutorial Practical Periods/week Credits TW POE Total
- - 3 3 2 25 25 50

1. Design and Experimental study of pre-tensioned concrete element in laboratory.

2. At least one Site visit and preparation of detailed report and a seminar on it.

Syllabus – VII sem Civil Engineering/ GU Page 29

 Elective II- B.E. Civil Engineering, VII Sem
Course Code: CE -721 Course: Industrial case study
Course scheme Evaluation scheme (Practical)
lecture Tutorial Practical Periods/week Credits TW POE Total
- - 3 3 2 25 25 50

Term work should consist of any two case studies of Civil Engineering live projects and
at least one seminar along with its report in spiral binding form for each case study.

Syllabus – VII sem Civil Engineering/ GU Page 30

 Elective II- B.E. Civil Engineering, VII Sem
Course Code: CE -722 Course: Project phase-I
Course scheme Evaluation scheme (Practical)
lecture Tutorial Practical Periods/week Credits TW POE Total
- - 3 3 2 50 50 100

Project phase-I shall consist of

1. Finalization of topic
2. Review of literature
3. Synopsis with complete outline of thesis
4. Data collection if any
5. Analysis phase-I
6. Minimum Two seminars based on above work.
The project work will be a design project – experimental project – field surveying or computer
oriented on any of the topics of Civil Engineering interest. It will allot as a group project consisting of
a minimum THREE and maximum Six number of students, depending upon the depth of project
work. The student is required to do literature survey, formulate the problem and form a methodology
of arriving at the solution of the problem. The term work assessment of the project will be done at the
end of the semester by a committee consisting of three faculty members from the department along
with Project Guide. The students will present their project work before the committee. The complete
project report is not expected at the end this semester. However a Ten pages typed report based on the
work done will have to be submitted by the students to the assessing committee. The project guides
will award the marks to the individual students depending on the group average awarded by the
committee. One Project Guide will be allotting Maximum TWO group for guidance.

Syllabus – VII sem Civil Engineering/ GU Page 31