Joysticks Catalogue

JOYSTICKS
JOYSTICKS AND GRIPS
Section / Description page
FINGERTIP PROPORTIONAL CONTROL LEVERS AND SWITCHES.................................................................. JK3
HEAVY DUTY MULTI-AXIS JOYSTICKS................................................................................................................ JK19
ERGONOMIC GRIPS .............................................................................................................................................. JK38
ACCESSORIES ...................................................................................................................................................... JK55
WARNING: the specifications/application data shown in our catalogs and data sheets are intended only as a general guide for the product described (herein). Any specific application should not be undertaken
W 42 / 2019
without independent study, evaluation, and testing for suitability.
4484 Boeing Drive Rockford, IL 61109 • USA • Phone +1 (815) 397-6628 • Fax +1 (815) 397-2526 Via Malavolti, 36 • 41122 Modena • ITALY • Phone +39 (059) 254895 • Fax +39 (059) 253512
mail: delta@delta-power.com • www.delta-power.com mail: tecnord@tecnord.com • www.tecnord.com
Page JK1
W 42 / 2019
Page JK2
JOYSTICKS
FINGERTIP PROPORTIONAL CONTROL LEVERS AND SWITCHES
DESCRIPTION ORDERING INFORMATION PAGE TECHNICAL INFORMATION PAGE
FTC proportional control lever JK4 JK9
FTH contactless proportional control lever JK5 JK12
JLP proportional control lever JK6 JK14
FPR proportional roller switch JK7 JK16
FPR - PWM proportional roller switch JK7 JK17
JMT proportional multi-axis JK8 JK18
W 42 / 2019
Page JK3
JOYSTICKS
FTC PROPORTIONAL CONTROL LEVER ORDERING INFORMATION
FTC - / _0 - -
Joystick family & type Main body configuration Y-Y axis control configuration Type of grip Pot. connector type
FTC Mini fingertip L1S Single axis, unidirectional IP Paddle type 0 None (only pin, solder type)
A Only potentiometer
control lever
L2S Single axis, bidirectional KC Cylindric type
1 4 poles electronic board on pot.
25%-75% signal
B Pot & Center switch

KC1 Cylindric type with AMP MODU I connector
“dead man” option
1 KΩ
(AMP p/n 280610/1)

C Pot & Bidirect. switches Mating connector kit included
3-pins rotary potentiometer
Z Pot & Bidirect. 2 8 poles electronic board on pot.

& Center switches and bidirectional switche
AMP MODU I connector
(AMP p/n 280612/1)
D Only potentiometer Mating connector kit included
E Pot & Center switch

5%-95% signal
5 KΩ
F Pot & Bidirect. switches
W Pot & Bidirect.

& Center switches
G Only potentiometer
H Pot & Center switch

0%-40% signal
10 KΩ
I Pot & Bidirect. switches

R Pot & Bidirect.

& Center switches
L Only potentiometer
0%-100% signal
M Pot & Center switch

5 KΩ
N Pot & Bidirect. switches
X Pot & Bidirect.

& Center switches
W 42 / 2019
Page JK4
JOYSTICKS
FTH CONTACTLESS PROPORTIONAL CONTROL LEVER ORDERING INFORMATION
FTH - / __ - - -
Joystick family & type Main body configuration Number of channels Type of grip Microswitch Connector
FTH Mini fingertip control L1S Single axis, unidirectional SN Single channel IPH Paddle type high version 00 None G Molex CGRID
lever hall effect 7 poles
L2S Single axis, bidirectional TW Twin channel IPL Paddle type low version 01 Center switch
(L2S only)
W 42/ 2019
Page JK5
JOYSTICKS
JLP PROPORTIONAL CONTROL LEVER ORDERING INFORMATION
JLP - L2S / _ 0 - IP -
Joystick family & type Main body configuration Y-Y axis control configuration Type of grip Output connector
JLP Mini fingertip L2S Single axis, bidirectional IP Paddle type D 7 pins dubox male connector
control lever Mod. 76382.407
(Q & R version)
10-90% signal
5KΩ
Q Pot & bidirect. switches E 4 pins Amp J. male connector

Mod. 929505-1
3 & 4 pins analog resistive track
(V version only)
G 7 pins molex C-Grid/SL male

0-100% signal
connector
Mod. COD.WM4929-ND
4KΩ
R Pot & bidirect. switches

(Q & R version)
25-75% signal
C Pot & bidirect. switches

2KΩ
Twin potentiometric
channel
V Twin channel
W 42 / 2019
Page JK6
JOYSTICKS
FPR FINGERTIP PROPORTIONAL SWITCHES ORDERING INFORMATION
FPR - L2S / _ _ CH - - -
Joystick family & type Main body configuration Number of channels Power supply range Body colour Connection
FPR Mini proportional L2S Single axis, bidirectional SN Single channel 0 5 VDC ±5% None Yellow None Flying leads
Hall effect TW Twin channel G Grey
H 8-32 VDC of power supply M Molex Minifit 4 poles
Roller switch
B Blue D Deutsch DT04-3P
GR Green
FPR-PWM - L2S / _ _ CH - - -
Joystick family & type Main body configuration Number of channels Power supply range Body colour Connection
FPR Mini Proportional L2S Single axis, bidirectional SN Single channel H 8-32 VDC of power supply None Yellow None Flying leads
Hall effect for dual coil
G Grey M Molex Minifit 6 poles
Roller switch proportional valve
B Blue
with PWM driver
W 42/ 2019
Page JK7
JOYSTICKS
JMT PROPORTIONAL MULTI-AXIS HALL EFFECT THUMB JOYSTICK
JMT - / ANL - A / F
Main base configuration YY / XX axes control config. Grip Configuration Connector type
L2S Single axis, bidirectional ANL Analog signal 0.5>2.5>4.5 VDC A Quad Convex F Flying leads 25 cm length
power supply range = 5 VDC ±5%
L4C Dual axes, cross movement
L4D Dual axes, all diagonals
W 42 / 2019
Page JK8
JOYSTICKS
FTC-L1S FINGERTIP PROPORTIONAL CONTROL LEVER
FEATURES
OVERALL DIMENSIONS
• Single axis / unidirectional.
• 3-pins rotary potentiometer.
• Optional enable switch.
MECHANICAL SPECIFICATIONS
Lever deflection angle: 50° ±1°

Electrical angle: 50° ±1°
Operating temperature range: -25°C / +80°C
Protection class: IP 65 (above panel)
Life: 3 million cycles
ELECTRICAL SPECIFICATIONS

Electrical power rating: 0.25 W @ 25°C
Ohmic resistance: / A = 50% of Vin 1 kΩ ±20%
/ D = 90% of Vin 5 kΩ ±20% Shown with paddle type grip. Small cylindrical grip KC type also
Max. operating input voltage (Vin): 48 V or ±24 V available, with optional dead man push button.
Min. load impedance on pin 2 (signal): 50 kΩ
Max. operating current on pin 2: 1 mA
Output voltage: see graph PANEL CUT-OUT
Linearity (resistive track): 2% or better
Connection type: 0 = solder type (no connector)
1 = AMP Modu I/ 4 poles con.
(mating connector kit included)
Neutral position switch (electromechanical type)

Contact: silver plated (solder type)
Max. operating input voltage: 48 V or ±24 V
Max. operating current: 1.5 A / inductive
OUTPUT SIGNAL CONTROL CHARACTERISTIC
Neutral pos. switch threashold angle: +4°
Protection class: IP 55 (IP 67 available on request)
POTENTIOMETER & SWITCHES OPTIONS

Reference codes
Output signal S= 50% Vin S= 90% Vin
3-pins pot A (Std) D
3-pins pot & enable switch B E
ELECTRICAL CONNECTIONS
Potentiometer Neutral position switch MC

FTC ORDERING INFORMATION: see page JK4
W 42/ 2019
Page JK9
JOYSTICKS
FEATURES
OVERALL DIMENSIONS
• Single axis / bidirectional.
• Optional center / power-off or bidirectional switches.
Lever deflection angle: ±25° ±1°

Electrical angle: ±25° ±1°

/ D = 90% of Vin 5 kΩ ±20% Shown with paddle type grip. Small cylindrical grip KC type also
Center / bidirectional switches (electromechanical type)

Contacts: silver plated (solder type)
Max. operating current: 1.5 A/inductive
Protection class: IP 55

3-pins potentiometer
Reference codes configuration
3-pin potentiometer A D
3-pin pot & center switch B E (Std)
3-pin pot & bidirectional switch C F
Potentiometer Same schematic for MA, FTC ORDERING INFORMATION: see page JK4
MB (bidirectional switches) or MC (center switch)
W 42 / 2019
Page JK10
JOYSTICKS
FEATURES
OVERALL DIMENSIONS
• Optional center / power-off or bidirectional switches.
Lever deflection angle: ± 25° ±1°

Electrical angle: ± 25° ±1°

Ohmic resistance: / G = 40% of Vin 1 kΩ ± 20%
/ L = 100% of Vin 5 kΩ ±20% Shown with paddle type grip. Small cylindrical grip KC type also
Center / bidirectional switches (electromechanical type)

Max. operating current: 1.5 A/inductive
Protection class: IP 55 (IP 67 available on request)

Reference codes
4-pin potentiometer G L configuration
4-pin pot & center switch H M
4-pin pot & bidirectional switchs I N (Std)
4-pin pot & bidirectional switchs
& center switch None X
Potentiometer Same schematic for MA,

MB (bidirectional switches)
or MC (center switch)
FTC ORDERING INFORMATION: see page JK4
W 42/ 2019
Page JK11
JOYSTICKS
FTH-L1S CONTACTLESS FINGERTIP PROPORTIONAL CONTROL LEVER
FEATURES
OVERALL DIMENSIONS
• Single axis / unidirectional.
• Contactless, hall effect sensor.
• Optional “out of neutral” switch.
• Optional dual sensor (redundant).
Lever deflection angle: 50° ±1°

Electrical angle: 50° ±1°
Life: > 3 million cycles (without switch)
Connector: molex CGRID/SL, 7 male pins
Linear, hall-effect sensor

Power supply voltage: 8÷32 VDC
Current consumption: < 15 mA (30 mA with 2 sensors) OUTPUT SIGNAL CONTROL CHARACTERISTIC
Output signal in neutral: < 0.1 V
Output signal range: 0.5 V ÷ 4.5 V
Tolerance on output signal: ±0.1 V
Linearity: < 2%
Max. output current: 1 mA
Directional switch operating voltage: < 48 VDC
Directional switch max. current: 1A FTH-L1S/SN
(single channel)
Max. operating current: 1A
Neutral pos. switch threashold angle: 7°
HS1: optional +Vb GND S1 S2 NO NC COM

1 2 3 4 5 6 7
8-32
HS1 HS2
5 FTH-L1S/TW
(dual channel)
PANEL CUT-OUT AND MOUNTING
FTH ORDERING INFORMATION: see page JK5
W 42 / 2019
Page JK12
JOYSTICKS
FTH-L2S CONTACTLESS FINGERTIP PROPORTIONAL CONTROL LEVER
FEATURES
OVERALL DIMENSIONS
• Contactless, hall effect sensor.
• Optional “out of neutral” switch.
• Optional dual sensor (redundant).
MECHANICAL / ENVIRONMENTAL SPECIFICATIONS

Life: > 3 million cycles (without switch)
Connector: molex CGRID/SL, 7 male pins
Paddle type high
Linear, hall-effect sensor
Power supply voltage: 8÷32 VDC
Current consumption: < 15 mA (30 mA with 2 sensors)
Output signal in neutral: 2.50 V ±0.1 V
Output signal range: 0.5 V ÷ 4.5 V
Tolerance on output signal: ±0.1 V
Linearity: < 2%
Max. output current: 1 mA
Directional switch operating voltage: < 48 VDC
Directional switch max. current: 1A

Max. operating current: 1A
Neutral pos. switch threashold angle: 7° Paddle type low
HS1: optional +Vb GND S1 S2 NC NO COM

1 2 3 4 5 6 7
8-32
5 HS1 HS2
FTH-L2S/SN (single channel) FTH-L2S/TW (dual channel)
FTH ORDERING INFORMATION: see page JK5
W 42/ 2019
Page JK13
JOYSTICKS
JLP-L2S FINGERTIP PROPORTIONAL CONTROL LEVER
FEATURES
OVERALL DIMENSIONS
• Single axis / bidirectional, panel mounting style.
• 3-4 pins potentiometer configuration.
• Bidirectional switches.

Fixing screws included: 2 - M4x16
Mod. D Dubox
Mod. G Molex
Potentiometer
/ Q = 80% of Vin 5 kΩ ±20%
/ R = 100% of Vin 4 kΩ ±20% PANEL CUT-OUT
Max. operating input voltage (Vin): 48 V or ±24 V
Output voltage: see graph
Directional switches
Typical track resistance: 150 Ohm
Min. load impedance on pins 2&3: 50 kΩ
Max. operating current on pins 2&3: 1 mA
Directional switches threashold angle: ±4° 3-pins
Connector type: Mod. D Dubox = P.N. 76382.407 wiring configuration wiring
Mod. G Molex = C-Grid P.N. 50-57-9407

Reference codes
Output signal S= 80% Vin S= 100% Vin S= 50% Vin
3-4 pins pot & bidir. switch Q R C
ELECTRICAL CONNECTIONS 4-pins

configuration wiring
JLP ORDERING INFORMATION: see page JK6
W 42 / 2019
Page JK14
JOYSTICKS
JLP-L2S TWIN CHANNEL FINGERTIP PROPORTIONAL CONTROL LEVER
FEATURES
OVERALL DIMENSIONS
• Single axis / bidirectional, panel mounting style.
• Twin channel potentiometer joystick.
• Redundancy on the 100% of the stroke.

Fixing screws included: 2 - M4x16 Yellow: output wiper 1
White: supply voltage (Vcc)
black sheat Yellow: output wiper 1
Black: 0 V (GND)
black sheat White: supply voltage (Vcc)
Brown: output
Yellow: wiper
output
Black:
2 1
0 V wiper
(GND)
black sheat White: supply
Brown: voltage
output (Vcc)
wiper 2
Yellow: output wiper 1
Black: 0 V (GND)
black sheat White: supply voltage (Vcc)
ELECTRICAL SPECIFICATIONS Brown: output wiper 2

Black: 0 V (GND) 4 Pin Amp J.
Brown: output wiper 2
Connector 929505-1
4 Pin Amp J.
Connector 929505-1
4 Pin Amp J.
Potentiometer 4 Pin Amp J. Connector 929505-1
Connector 929505-1

Total resistance between pin 1 and 3: 2 kΩ ±20%
Nominal voltage supply (Vin): 10 V
Tolerance between track 1 and 2: ± 4% of Vcc
Output voltage: see graph
Load resistance: 100 kΩ - nominal
50 kΩ - minimum
Connector type: AMP JPT P.N. 929505-1 PANEL CUT-OUT

Reference codes
Output signal S= 60% Vin
3 pins potentiometer V
ELECTRICAL CONNECTIONS OUTPUT SIGNAL CONTROL CHARACTERISTIC

Pinout
4 Brown: output wiper 2
1 White:
4 Brown: supply
output voltage
wiper 2 (Vcc)
1 White: supply voltage (Vcc)
1 White: supply
1 White: voltage
supply (Vcc)(Vcc)
voltage
3 Black: 0 V (GND)
3 Black:
2 Yellow: output0 wiper
V (GND)
1
3 Black: 0 V (GND)
3 Black: 0 V (GND)
2 Yellow: output wiper 1
2 Yellow: output
2 Yellow: wiperwiper
output 1 1
JLP ORDERING INFORMATION: see page JK6
W 42/ 2019
Page JK15
JOYSTICKS
FPR-L2S PROPORTIONAL ROLLER SWITCH WITH HALL EFFECT SENSOR
FEATURES
• Mini proportional roller switch with optimum ergonomic design for
panel-mounting.
• High performance hall effect sensor circuitry.
• Twin channel configuration for redundancy.
Rotation angle: ±30°

Body material: acetal resin / teflon compound
Colours available: grey, blue, green, yellow
Rubber gaiter material: EPDM / 35-45 shore - A
PANEL CUT-OUT
Environmental protection: IP 68 (above panel)
Life: > 5.000.000 cycles
Signal output @ rest: 2.5 VDC ±0.1 V

Supply voltage: H - Version = 8÷32 VDC
0 - Version = 5 VDC ±5%
Full output signal range: 0.5 - 4.5 V, ±0.2 V
Current consumption at rest: SNCH (S1 only) 15 mA OUTPUT SIGNAL CONTROL CHARACTERISTIC
TWCH (S1/S2) 25 mA
Rated output current: 1 mA
Connection type: flying leads = coloured flat cable 100 mm
connector = molex Minifit 4 poles P.N. 5559-4P
Deutsch 3 poles P.N. DTO4-3P
FPR - L2S - SNCH (single chan.) FPR - L2S - TWCH (twin chan.)
(1) Yellow: +5 VDC (1) Yellow: + 5 VDC

(2) Orange: (-) ground (2) Orange: (-) ground
(3) Red: output 1 (S1) (3) Red: output 1 (S1) FPR-L2S/ SNCH (single channel)
(4) Brown: not used (4) Brown: output 1 (S2)
OVERALL DIMENSIONS
FPR-L2S-TWCH (twin channel)
FPR ORDERING INFORMATION: see page JK7
W 42 / 2019
Page JK16
JOYSTICKS
FPR-PWM-L2S PROPORTIONAL ROLLER SWITCH WITH PWM DRIVER
FEATURES
• Mini proportional roller switch with optimum ergonomic design for
panel-mounting.
• PWM electronic driver integrated into the roller for remote control
of a dual-coil proportional solenoid valve.
Rotation angle: ±30°

Main body material: acetal resin / teflon compound
Colours available: yellow, grey, blue
Rubber gaiter material: EPDM / 35-45 shore - A
Operating temperature range: -25°C / +85°C PANEL CUT-OUT
Environmental protection: IP 68 (above panel)
Life: > 5.000.000 cycles
Supply voltage: 8÷32 VDC

Current consumption with no load: 100 mA
PWM dither frequency: 100 Hz
Wire lenght: 700 mm
PWM OUTPUT CHARACTERISTIC EXAMPLE
Current output range (PWM): 100÷1500 mA @ 12 VDC
Connection type: flying leads = GLX 0.5 sqmm
connector = molex Minifit 6 poles P.N. 5559-6P

(1) Red: +Battery

(2) Black: -Battery (GND)
(3) Orange: PWM Valve A+
(4) Gray: PWM Valve B+
(5) White: PWM A- / B- (common) The following values are factory set:
(6) Not used • Imin (minimum output current)
• Imax (maximum output current)
OVERALL DIMENSIONS • Dither
APPLICATION EXAMPLE
Ordering Code
FPR ORDERING INFORMATION: see page JK7 23.0409.160 (Imin = 200mA, Imax = 1500mA, PWM = 100Hz)
W 42/ 2019
Page JK17
JOYSTICKS
JMT PROPORTIONAL MULTI-AXIS HALL EFFECT THUMB JOYSTICK
FEATURES
• Mini proportional thumb joystick with ergonomic design for panel OVERALL DIMENSIONS
mounting.
• Suitable for grips, controls panels, armrests or belly boxes.
• Analog voltage outputs, factory pre-set.
• One/two axis gated or 360°.
• 1 million cycle mechanical life.
Type of movement: single, cross or

omnidirectional square type
Travel angle: 23°±2°
Operating force with boot: 2-3 N
Maximum vertical/horizontal load: 200 N / 150 N
Life: 1.000.000 cycles
Case material: Thermoplastic, black
Boot material: EPDM - UV proof, black
Operating temperature range: -40°C / +85°C PANEL CUT-OUT
Cutout dimensions
Max panel thickness: 3+/-0.2 mm
Sensor technology: Hall effect

Supply Voltage: ANL = 5 VDC ±5%
Protection: reversed voltage,
overvoltage, short circuit
on outputs
Current consumption: < 20 mA
Output signal ratiometric (ref. to 5.0V): 0.5-4.5V
Output voltage tolerance at center: < 0.25V
Output voltage tolerance at full travel: < 0.25V
Sealing (fully potted electronics): IP69K
JMT - L2S - single axis JMT - L4C/D - dual axis
(1) Red: +5 VDC (1) Red: +5 VDC

(2) Black: (-) ground (2) Black: (-) ground
(3) Yellow: output Y (3) Yellow: output Y
(4) Blue: not used (4) Blue: output X
Wires Coloured AWG 24
JMT ORDERING INFORMATION: see page JK8
W 42 / 2019
Page JK18
JOYSTICKS
HEAVY DUTY MULTI-AXIS JOYSTICKS
JMF potentiometric joystick body JK20 JK22
JHM hall effect joystick body JK21 JK28
Note: 1) The joystick base does not include the grip.

2) The joystick base includes the rubber gaither.
W 42/ 2019
Page JK19
JMF
Page JK20
JMF - / __ - - -
Joystick family & type Main base configuration YY / XX axes control config. Type of grip Grip configuration Pot. connector type
JMF Heavy duty / Multi-axis L1SF Single axis, unidirectional 0 No Pot. & switches on Y/X axis IL Cylindrical knob Refer to the Grip ordering 0 Flying leads
joystick controller with friction lock information for zz e kk 25 cm length
2 Only Bidir. switches on Y/X axis IC Cylindrical
L2S Single axis, bidirectional axes (push-buttons &
1 4 poles electronic board
A Only potentiometer IE Multi-function proportional controls
on potentiometer
L2SF Single axis, bidirectional ergonomic on grips)
AMP MODU I connector
1 KΩ
signal
with friction lock
25%-75%
C Pot. & Bidirect. switches MS Multi-function (AMP p/n 280610/1)
mail: delta@delta-power.com • www.delta-power.com

L4C Dual axes, cross movement ergonomic symmetric mating connector

D Only potentiometer kit included
L4D Dual axes, all diagonals MG Multi-Function
5 KΩ
signal
ergonomic right hand
5%-95%
F Pot. & Bidirect. switches

HL Multi-function
G Only potentiometer ergonomic left hand
HEAVY DUTY MULTI-AXIS JOYSTICK
HR Multi-function
signal
10 KΩ
0%-40%
I Pot. & Bidirect. switches ergonomic right hand
L Only potentiometer
5 KΩ
signal
0%-100%
N Pot. & Bidirect. switches
4484 Boeing Drive Rockford, IL 61109 • USA • Phone +1 (815) 397-6628 • Fax +1 (815) 397-2526
JMF-L4C/NN-MG/A6P9/0000/R000-0
EXAMPLE: COMPLETE JOYSTICK
mail: tecnord@tecnord.com • www.tecnord.com

+ = (with flying leads)
JMF-L4C/NN MG/A6P9/0000/R000-0
BASE GRIP
Via Malavolti, 36 • 41122 Modena • ITALY • Phone +39 (059) 254895 • Fax +39 (059) 253512
ORDERING INFORMATION
JOYSTICKS
W 42 / 2019
W 42/ 2019
JHM
JHM - / - / -
Joystick family & type Main base configuration YY / XX axes control config. Type of grip Grip Configuration Connector type
JHM Heavy duty / Multi-axis L2S Single axis, bidirectional ANL Analog signal 0.5>2.5>4.5 VDC IL Cylindrical knob Refer to the grip 3 Flying leads
hall effect type power supply range = 5 VDC ±5% ordering information 25 cm length
joystick controller L4C Dual axes, cross movement IC Cylindrical
ANH Analog signal 0.5>2.5>4.5 VDC for zz e kk axes
4 Male connector,
L4D Dual axes, all diagonals power supply range = 8-32 VDC IE Multi-function (push-buttons &
12 poles,
ergonomic proportional controls
Deutsch DT04-12P,
AVS Center tap output signal with on grips)
25 cm cable length
mail: delta@delta-power.com • www.delta-power.com

digital directional signals MS Multi-function
ergonomic symmetric 5 Male connector,

MLT adjustable output signal
for closed loop prop. actuators MG Multi-function 4 poles,
ergonomic right hand Deutsch DT04-4P,
RTM adjustable output signal 25 cm cable length
for closed loop prop. actuators HL Multi-function (for CANbus version only)
ergonomic left hand
PWM Pulse with modulation current 6 Male connector,
HEAVY DUTY MULTI-AXIS JOYSTICK
output factory preset or set via PC HR Multi-function 6 poles,

ergonomic right hand Deutsch DT04-6P,
TCN 1 PWM ouput in combination 25 cm cable length
with up to 4 on-off channels
7 Male connector,
CAN CANbus version for connection to 8 poles,
4484 Boeing Drive Rockford, IL 61109 • USA • Phone +1 (815) 397-6628 • Fax +1 (815) 397-2526
CANbus line J1939 protocol Deutsch DT04-8P,
25 cm cable length
Note:
for TCN, PWM and MLT
versions, a 4 poles, Deutsch
DT04-4P connector is
always included
JHM-L4D/ANH-MS/0000/2FPR/R000-6
mail: tecnord@tecnord.com • www.tecnord.com

EXAMPLE: COMPLETE JOYSTICK
+ = (with 6 poles Deutsch connector)
SMUSSI NON QUOTATI 0.2x45°;

-
-
-
-
-
-
-
SMUSSI NON QUOTATI 0.2x45°;

-
-
-
-
-
-
-
RACCORDI NON QUOTATI R0.2;

G
F
E
D
C
B
A
RACCORDI NON QUOTATI R0.2;

G
F
E
D
C
B
A
PARTICOLARE ESENTE DA BAVE E AMMACCATURE. MODIFICHE APPROVATE

PARTICOLARE ESENTE DA BAVE E AMMACCATURE. MODIFICHE APPROVATE
DESCRIZIONE: JSTK SOSTITUISCE IL:

-
DESCRIZIONE: SOSTITUISCE IL:
-
JHM-L4D/ANL-MS-03P9/2FPR/RSELMARQ-DT04-12P
TECNORD
SERVOCOMANDI E REGOLAZIONE
TECNORD - SERVOCOMANDI E REGOLAZIONE
JHM-L4D/ANH-6
- JSTK SOSTITUITO DA: IL PRESENTE DISEGNO E' DI PROPRIETA' TECNORD
S.R.L. E' VIETATA LA RIPRODUZIONE, DIFFUSIONE A
MS/0000/2FPR/R000 IL PRESENTE DISEGNO E' DI PROPRIETA' TECNORD
TERZI E QUALUNQUE USO NON AUTORIZZATO CHE
SOSTITUITO DA:
S.R.L. E' VIETATA LA RIPRODUZIONE, DIFFUSIONE A
-
JHM-L4D/ANL-MS-03P9/2FPR/RSELMARQ-DT04-12P POSSA ARRECARE DANNO AL PROPRIETARIO.
TERZI E QUALUNQUE USO NON AUTORIZZATO CHE
NOME FILE: SCALA DATA N° FOGLIO - POSSA ARRECARE DANNO AL PROPRIETARIO.
TRATT. SUPERFICIALE:
TECNORD_bianco 2014.idw NOME FILE: SCALA DATA N° FOGLIO
TRATT. TERMICO: - 22/07/2014 1 1 TRATT. SUPERFICIALE:
MATERIALE: MASSA: N/A SF. - TECNORD_bianco 2014.idw -
A4 TRATT. TERMICO: 11/07/2014 1 1
BASE
CLIENTE RUG. GEN. COMPLESSIVO DISEGNATO VERIF. APPROV.
CODICE
GRIP
- 3.2 - R.B. MATERIALE: MASSA: N/A SF. A4
CLIENTE RUG. GEN. COMPLESSIVO DISEGNATO VERIF. APPROV.
QUOTE SENZA TOLLERANZA: da 0 a 1: ±0.05 da 1 a 80: ±0.1 da 80 a 200: ±0.15 da 200 a 300: ±0.2 da 300 a 600: ±0.3 JHM+MS A 3.2 CODICE
- - R.B.
QUOTE SENZA TOLLERANZA: da 0 a 1: ±0.05 da 1 a 80: ±0.1 da 80 a 200: ±0.15 da 200 a 300: ±0.2 da 300 a 600: ±0.3 13.8101.265
Via Malavolti, 36 • 41122 Modena • ITALY • Phone +39 (059) 254895 • Fax +39 (059) 253512
ORDERING INFORMATION
Page JK21
JOYSTICKS
JOYSTICKS
JMF HEAVY DUTY MULTI-AXIS POTENTIOMETRIC JOYSTICK (JOYSTICK BASE ONLY)
FEATURES
AVAILABLE JOYSTICK MOVEMENTS
The JMF potentiometeric joystick controller has been designed for
use in mobile and industrial field application. The potentiometer in *Option L1S Single axis control / Unidirectional
use, available with 3 or 4-pins configuration, grants precision and a *Option L2S Single axis control / Bidirectional
long working life. Option L4C Cross axis control / Bidirectional
When coupled with an M range of ergonomic multi-function handles, Option L4D Multi axis control / Bidirectional
up to 5 proportional axes and 9 on-off push buttons can be integrated
in the same joystick. Power directional switches are available. * friction lock option available for L1S and L2S

Protection class (above panel): up to IP 67, depending on grip
POTENTIOMETER & SWITCHES OPTIONS (Y-Y AND X-X AXIS)

Reference codes
3-pins pot A D
3-pins pot & bidirectional switchs C F (Std)
Reference codes
Output signal S= 40% Vin S=100% Vin
4-pins pot G L
4-pins pot & bidirectional switchs I N (Std)
Shown with IC grip
W 42 / 2019
Page JK22
ax. operating . Pot.
. Max. operating
current: connector type:
current: 3 A / inductive0 = none (solder type)
3 A / inductive
F Heavy
. Neutralswitch
eutral position position Duty
threashold
switch Multi-Axis
threashold
angle: angle: Potentiometric
+4° +4° Joystick
1 = AMP(joystick
Modu I/4 base
poles only)
ot. connector type: . Protection
. Pot. connector type: class: 0 = none 0(solder
= nonetype) IP 55
(solder (specials available
type) JOYSTICKS
1 = AMP 1Modu
= AMP
I/4 Modu on request)
poles I/4 poles
rical specifications
otection JMF class:
. Protection
class: HEAVY DUTY MULTI-AXIS POTENTIOMETRIC JOYSTICK (JOYSTICK BASE ONLY)
IP 55 (specials
IP 55 (specials
available available
on request)
on request)
ional switchesELECTRICAL
(electromechanical type)
SPECIFICATIONS Output
OUTPUT signal
SIGNAL control
CONTROL characteristics
CHARACTERISTICS
acts:
Rotary potentiometer
Silver Plated
Directional. switches
Electrical power rating:
(electromechanical type) 0.25 W @ 25°C
operating input voltage: 48 V or +/-24V
Contacts: silver plated
operating current:
ary potentiometer
Rotary potentiometer 3 A / inductive
Max. operating input voltage: 125/250 Vac
al position switch threashold angle:resistance:
. Ohmic / +4°
AA (5
= A50% of Vin 1 k ё +/- 20%
ectrical . Electrical
power
Max.rating:
power
operating rating:
current: 16 0.25 W @0.25
on request)* 25°CW @ 25°C
connector type:Pot. connector type: 00 == none(solder
None (solder type)
type)
(3-pins version) / D = 90% of Vin 5 k ё +/-20%
11
==AMP
AMPModu
ModuI/4I/4
poles
poles
hmic . Ohmic
resistance:
ction class: resistance:
Neutral / Aswitch
pos. = 50% / of
A =Vin
50%
threashold of ±10°
angle: Vin (±5°
IP 55 1 k ё +/- 20%
on request)*
(specials available 1 k ё +/- 20%
Protection .class: IP 55
(3-pins version) / DOhmic
(3-pins version) = 90%/resistance:
D
of =Vin
90% of Vin / G = 40% of Vin
on request) 5 k ё +/-20% 10 k ё +/- 20%
5 k ё +/-20%
(specials available on request)
(4-pins version) / L = 100% of Vin 5 k ё +/-20% 3-pins pot.
Rotary potentiometer
configuration
. Ohmic
hmic resistance: resistance:
/ G = 40%/ G of =Vin
40% of Vin 10 k ё +/-10
20%
k ё +/- 20%
y potentiometer Electrical power rating: 0.25 W @ 25°C
(4-pins
rical powerversion)
(4-pins
rating: / .LMax.
version)
Ohmic resistance: = 100% operating
/ A /=L50%
of= Vin
100% input 0.25
voltage
of Vin of1 Vin
(Vin):
W @ 25°C 5 k ё +/-20%
kΩ ±20% 5 k ё +/-20%48 V or +/-24 V
. Min. /load
(3-pins version) impedance
D = 90% of Vin 5 kΩon ±20%
pin 2 (Signal): 50 k ё
c resistance: Ohmic
/ A = resistance:
50% of Vin / G = 40% of Vin 101kΩ ±20%
input .voltage
. Max. operating
ax. operating Max. operating
input voltage current
(Vin): (Vin): on k ё pin 2: 48 V or +/-24
+/- 20% 48 VVor +/-24 1V mA
pins version) (4-pins
/ D = 90% version) / L = 100% of Vin 5 kΩ ±20%
of Vin 5 k ё +/-20%
n. load . Min.
impedance
loadoperating
Max. . Output
impedance
on pin voltage:
input2voltage
(Signal):
on pin 2 (Signal):
(Vin): 48 V or ±24 V 50 k ё 50 k ё See graphs
ax. . Max.Min.
operating
c resistance: /operating
current
G = 40% on
. Linearity
load impedance pin on
ofcurrent
Vin
(resistive
2:pin
on2pin 2: track):
(signal): 50 kΩ
10 k ё +/- 20% 1 mA 1 mA 2% or better
utput . Output
voltage:
pins version) / Lvoltage:
Output = 100% . Protection
voltage:of Vin class: k ё +/-20% See graphs
see5graphs See graphs IP 67
nearity. (resistive
Linearity
Linearity (resistive
track): track):
(resistive track): 2% or better 2% or better
2% or better
operating input Protection
voltage class:
(Vin): IP48
67V or +/-24 V
otection. Protection
class: Electrical connections (forIPsolder
class: 67 type
IP 67 connector)
oad impedance on pin 2 (Signal): 50 k ё
operating current on pin 2: 1 mA
ectricalElectrical
ut voltage: connections
connections
ELECTRICAL (for solder
CONNECTIONS (for
(for type
solder
See
solder connector)
graphs
type type connector)
connector)
rity (resistive track): 2% or better
ction class: IP 67
rical connections (for solder type connector)

4-pins pot.
configuration
3-pins potentiometer 4-pins potentiometer

22° 22°
NO NC C
pins potentiometer 4-pins potentiometer
NO NCNO CNC C Directional switches Ordering inf

NO NC C (see pinout on switch)
Directional
Directional
switches switches Ordering
Ordering Available
information:
information:grs
see page
(see pinout
(see
onpinout
switch)on switch) Ordering information: see page 17
(see pinout on switch) JMF ORDERING INFORMATION: see page JK20
(see pinout on switch) Available
Available Complete
grips: see
grips:
pagesee jo
34pag
Available grips: see page 34
Complete
Complete joystick examples: Complete
seejoystick
next pagejoystick
examples:
exam
se
W 42/ 2019
WARNING: The specifications/application data shown in our catalogs and data sheets are intended only
Page JK23
(herein). Anydata
NG: The specifications/application specifi
shownc application
in our catalogsshould
and datanot be are
sheets undertaken without
intended only independent
as a general study,
guide for the evaluation,
product described and te
Any specific application should not be undertaken without independent study, evaluation, and testing for suitability.
JOYSTICKS
JOYSTICKS
JOYSTICKS
MF JMF HeavyHeavy
Duty Multi-Axis Potentiometric
Duty Multi-Axis Joystick JOYSTICKS
Joystick
Potentiometric JOYSTICKS
JMF HEAVY DUTY MULTI-AXIS POTENTIOMETRIC JOYSTICK
JMF JMF joystick
JMF with grips
JMF joystick Heavy
Heavy
with
JMF joystick
-grips
configuration
Duty
withDuty examples
Multi-Axis
-Multi-Axis
- configuration
grips configuration
with overall
Potentiometric
Potentiometric
examples
examples
dimensions
Joystick
Joystick
withwith overall
overall dimensions
dimensions
22°
JMF
JMFjoystick
joystickwith
withgrips
grips--configuration
configurationexamples
exampleswith
withoverall
overall dimensions22°
dimensions
22° 22°
MF base with IL handle JMF base with IL handle JMF base with ICJMF base with IC handle
handle
JMF base with Complete
IL handlecode: JMF-L4C/NN-IL 0000 JMFComplete
base with IC handle
omplete
JMFcode:
JMF baseJMF-L4C/NN-IL
base with handle 0000
withILILhandle Complete
JMF
JMFbasecode:
basewith
withIC handle JMF-L4C/NN-IC
code:
JMF-L4C/NN-IC
IChandle 0200 0200
Complete code: JMF-L4C/NN-IL 0000 Complete code: JMF-L4C/NN-IC 0200
Complete
Completecode:
code:JMF-L4C/NN-IL
JMF-L4C/NN-IL0000
0000 Complete
Completecode:
code:JMF-L4C/NN-IC
JMF-L4C/NN-IC0200
0200
22° 22° 22° 22°
JMF
JMFbase
basewith
withIE JMF
IEtype
type base with IE type handle
handle
handle JMF
JMFbase withJMF
basewith IE base
IEtype
type with IE type handle
handle
handle
MF base
Complete
Complete Complete
with IEcode:
type
code: code: JMF-L4C/NN-IE
handle
JMF-L4C/NN-IE
JMF-L4C/NN-IE A3P9 0000A3P9 0000
A3P90000 JMF Complete
base
Completewith
Completecode:
code: type JMF-L4C/NN-IE
code:
IEJMF-L4C/NN-IE
handle A1P9
JMF-L4C/NN-IE A1P9 A1P9
1PRS1PRS
1PRS
JMF base with IE type handle JMF base with IE type handle
omplete code: JMF-L4C/NN-IE A3P9 0000 Complete code: JMF-L4C/NN-IE A1P9 1PRS
Complete code: JMF-L4C/NN-IE A3P9 0000 Complete code: JMF-L4C/NN-IE A1P9 1PRS
W 42 / 2019

WARNING:
WARNING:The Thespecifi
specifications/application
cations/applicationdata
datashown
shownininour
ourcatalogs
catalogsand
anddata
datasheets
sheetsare
areintended
intendedonly
onlyasasaageneral
generalguide
guidefor forthe
theproduct
productdescribed
described
(herein).
(herein).Any
Anyspecifi
specificcapplication
applicationshould
shouldnot
notbe
beundertaken
undertakenwithout
withoutindependent
independentstudy,
study,evaluation,
evaluation,and
andtesting
testingfor
forsuitability.
suitability.
WARNING: The specifications/application data shown in our catalogs and data sheets are intended only as a general guide for the product described
(herein).4484
AnyBoeing
specific application should not be +1 undertaken without independent study, evaluation, and testing for suitability.
(herein). Drive
AnyRockford,
specificIL application shouldPhone
61109 • USA • Phone Phone
not
(815) be+39
+39 059
•059
Fax254895
undertaken
397-6628 254895
+1 •• Fax
without
(815) Fax +39
+39 059
independent
397-2526 Via 059253512
253512
study,
Malavolti, •Modena
• E-mail:
E-mail:
evaluation,
36 • 41122 tecnord@tecnord.com
• and tecnord@tecnord.com
ITALY testing for(059)
• Phone +39 suitability.
254895 • Fax +39 (059) 253512
Phone +39 059 254895 • Fax +39 059 253512 • E-mail: tecnord@tecnord.com
Phone +39 059JOYSTICKS
254895- - page
JOYSTICKS •page
Fax24 +39 059 253512 • E-mail: tecnord@tecnord.com
24
Page JK24
JOYSTICKS - page 24
JOYSTICKS
JOYSTICKS JOYSTICKS
JOYSTICKS
JMF JOYSTICKS
JMFHEAVY
JMF DUTY MULTI-AXIS POTENTIOMETRIC
Heavy
Heavy
DutyDuty JOYSTICK
Multi-Axis
Multi-Axis
Potentiometric
Potentiometric
Joystick
Joystick
JMF joystick with grips - configuration examples with overall dimensions
JMFJMF JMF JMF
joystick Heavy
joystick
with Heavy
with
grips Duty
grips -Duty
Multi-Axis
Multi-Axis
- configuration Potentiometric
configuration Potentiometric
examples
examples Joystick
with with
overall Joystick
overall
dimensions
dimensions
JMF joystick
JMF joystick
with grips
with grips
- configuration
- configuration
examples
examples
with overall
with overall
dimensions
dimensions
22° 22° 22° 22°
22° 22° 22° 22°
JMF base
JMF with
baseMSwith
type
MShandle
type handle JMF base
JMF with
baseMS
with
type
MShandle
type handle
Complete
Complete
code: code:
JMF-L4C/NN-MS
JMF-L4C/NN-MS
A6P9 A6P9
R3P9 R3P9 Complete
Complete
code: code:
JMF-L4C/NN-MS
JMF-L4C/NN-MS
A2P9 A2P9
2FPR 2FPR
R1P9 R1P9
JMF base with MS type handle JMF base with MS type handle
Complete
JMF base
JMF with
baseMScode:
with
type
MSJMF-L4C/NN-MS
handle
type handle A6P9 R3P9 Complete
JMF JMFcode:
base with JMF-L4C/NN-MS
baseMS
with
type
MShandle A2P9 2FPR R1P9
type handle
Complete
Complete
code: JMF-L4C/NN-MS
code: JMF-L4C/NN-MS
A6P9 A6P9
R3P9 R3P9 Complete
Complete
code: JMF-L4C/NN-MS
code: JMF-L4C/NN-MS
A2P9 A2P9
2FPR 2FPR
R1P9 R1P9
22° 22°
22° 22° 22° 22°
22° 22°
JMF base
JMF with
baseMG
withtype
MGhandle
type handle JMF base
JMF with
baseMG
withtype
MGhandle
type handle
Complete
Complete
code: code:
JMF-L4C/NN-MG
JMF-L4C/NN-MG
A4P9 A4P9
R1P9 R1P9 Complete
Complete
code: code:
JMF-L4C/NN-MG
JMF-L4C/NN-MG
A2P9 A2P9
1FPR 1FPR
R1P9 R1P9
JMF base JMFwithbaseMGwithtype

MGhandle
type handle JMF base JMFwith
baseMG withtype
MGhandle
type handle
Complete Complete
code: JMF-L4C/NN-MG
code: JMF-L4C/NN-MG A4P9 A4P9
R1P9 R1P9 Complete Complete
code: JMF-L4C/NN-MG
code: JMF-L4C/NN-MG A2P9 A2P9
1FPR 1FPR
R1P9 R1P9
WARNING:
WARNING: JMF
The specifi
The basecations/application
with MG type
cations/application
specifi handle
data shown
data in
shown
our catalogs
in our catalogs
and data
and
sheets
data sheets
are intended onlyJMF
are intended base
as only as a with
a general MG
general
guide for type
guide handle
the for
product
the product
described
described
Complete
(herein).(herein).
Any specifi code:
Anycspecifi JMF-L4C/NN-MG
application
c application
should should
not be not A4P9
undertaken
be R1P9
undertaken
withoutwithout
independent
independent Complete
study, evaluation,
study, and code:
evaluation,
testing JMF-L4C/NN-MG
and testing for suitability. A2P9 1FPR R1P9
for suitability.
Phone Phone
+39 059
+39
254895
059 254895
• Fax• +39
Fax059
+39
253512
059 253512
• E-mail:
• E-mail:
tecnord@tecnord.com
tecnord@tecnord.com
WARNING:WARNING:
The specifi
Thecations/application
data shown
data in
shown
our catalogs
in our catalogs
and dataand
sheets
data are
sheets
intended
are intended
only as only
a general
as a general
guide forguide
the product
for the product
described
described
(herein).(herein).
Any specifi
Anycspecifi
application
c application
should not
should
be undertaken
not be undertaken
withoutwithout
independent
independent
study, evaluation,
study, evaluation,
and testing
and testing
for suitability.
for suitability.
W 42/ 2019
without independent study, evaluation, and testing for suitability. JOYSTICKS - page -25
JOYSTICKS page 25
Phone Phone
+39 059
+39
254895
059 254895
• Fax •+39
Fax059
+39
253512
059 253512
• E-mail:
• E-mail:
tecnord@tecnord.com
tecnord@tecnord.com
JOYSTICKS - page -25page 25

JOYSTICKS
Page JK25
JOYSTICKS
JMF HEAVY DUTY MULTI-AXIS POTENTIOMETRIC JOYSTICK
HL joystick with grips - configuration examples with overall dimensions
22° 22°
JMF base with HL type handle JMF base with HL type handle
Complete code: JMF-L4C/NN-HL-04P9-2P9/RDFF Complete code: JMF-L4C/NN-HL-04P9-2P9/RDFF
22° 22°
JMF base with HR type handle JMF base with HR type handle
Complete code: JMF-L4C/NN-HR-0FPR-2P9/R000 Complete code: JMF-L4C/NN-HR-0FPR-2P9/R000
W 42 / 2019
Page JK26
W 42 / 2019
Page JK27
JOYSTICKS
JOYSTICKS
JHM
JHM HEAVY DUTY MULTI-AXIS
Heavy Duty HALL EFFECT Hall
Multi-Axis JOYSTICK
Effect(JOYSTICK
Joystick BASE ONLY)
(joystick base only)
FEATURES
Features AVAILABLE joystick
JOYSTICK
Available movements
MOVEMENTS
The JHM joystick controller has been designed for use in mobile and
industrial
The fieldcontroller
JHM joystick applications.
has been The use of
designed for the hall
use in effect
mobile and sensor,
industrial which Option L2S L2S Single axis
Option control
Single / Bidirectional
axis control / Bi-directional
eliminates
Field any
applications. Thecontact
use of thebetween
hall effect moving electrical
sensor, which parts,
eliminates any improves Option L4C L4C Cross axis
Option control
Cross / Bidirectional
axis control / Bi-directional
overall
contact resolution,
beetween precision
moving electrical and
parts, life. A
improves complete
overall line of built-in
resolution, Option L4D L4D Multi axisMulti-axis
Option control control
/ Bidirectional
/ Bi-directional
electronic
precision drivers,
and life. generating
A complete on-off,
line of built-in proportional
electronic drivers,and CANbus
generating control
on-off,
signals, guarantees
proportional the highest
and CANbus control controllability
signals, guarantees of any type of electro-
the highest
hydraulic system.
controllability of any type of electro-hydraulic system. * Shown with MS grip
When
When coupled
coupled with anwith an ergonomic
ergonomic handle of the M range,
multi-functionmulti-function handle to 5the M
up of
range, upaxes
proportional to and
5 proportional axes and
9 on-off push buttons can be 9 integrated
on-off push in thebuttons
same can be
integrated
joystick. in the
As further same
option, the joystick.
JHM is also available with a magnetic position
A magnetic
detent on the Y- orposition
X- axis. detent on the Y or X axis is also available as
option.
Mechanical
MECHANICALspecifications
SPECIFICATIONS
Mainbody
. Main body material:
material: aluminium
aluminium
Bootmaterial:
. Boot material: EPDMNBR- /UV
Shoreproof
50 - UV proof
Lever deflection
. Lever deflection angle:
angle: ±22°± 22°
±1° ±1°
Electrical
. Electrical angle:
angle: ±22°± 22°
±1° ±1°
Operating
. Operating temperature
temperature range:range: -25°C / +80°C
-25°C / + 80°C
Protection
. Protection class
class (above
(above panel):
panel): up to
upIP 67,67,depending
to IP ongrip
depending on grip
. Life:
Life: > 5 million
> 5 million cycles
cycles
Electrical specifications
. Sensor: Hall Effect contactless technology
Sensor:
. Supply
voltage: ANL versionhall=effect
5 Vdc contactless
+/-5% technology
Supply voltage: ANL=version
other versions 8 - 32 Vdc = 5 VDC ±5%

. Current consumption @ rest: otheronly)
25 mA (sensor versions = 8÷32 VDC
Current
. Output consumption
signal configuration:@ rest:see
next pages
25 mA for (sensor only)
all versions
Connector
. Connector type:
type: Deutsch DT04-12P
Deutsch DT04-12P
other typesother types
available on available
request on request
Output signal configuration: see next pages for all versions

Panel cut-out and mounting
Shown with MS grip
Ordering information: see page 21
JHM ORDERING
Available grips: see INFORMATION:
page 38-45 see page JK21
Complete joystick examples: see page 32-33
W 42 / 2019
(herein). Any specific application should not be undertaken without independent study, evaluation, and testing for suitability.
Page JK28
JOYSTICKS - page 26
JOYSTICKS
JHM HEAVY DUTY MULTI-AXIS HALL EFFECT JOYSTICK (JOYSTICK BASE ONLY)
ANL & ANH VERSION AVS VERSIONS
Basic version Center tap output signal with digital directional signals
Current consumption @ rest: < 25 mA (sensor only) Current consumption @ rest: < 150 mA (without external load)
Supply voltage: ANL version = 5 VDC ±5% Supply voltage (Vin): 8÷32 VDC
ANH version = 8÷32 VDC Signal output @ rest: 0V
Signal output @ rest: 2.5 VDC ±0.2 V Output signal range: 0÷5 V ±0.2 V (see graph)
Output signal range: 0.5 ÷ 4.5 V ±0.2 V (see graph) Rated output current: 1 mA
Rated output current: 1 mA
Protections (ANH version): overvoltage and reversed polarity (MA and MB signals on graph)
Digital directional outputs on both axes: 0 / Vin (0.7 A max)
Digital directional outputs switching angle: between 2° and 5°
OUTPUT SIGNAL CONTROL CHARACTERISTICS OUTPUT SIGNAL CONTROL CHARACTERISTICS
22° 22°
Lever deflection angle Lever deflection angle
W 42/ 2019
Page JK29
JOYSTICKS
MLT VERSION APPLICATION EXAMPLE
Adjustable output signal for closed loop proportional actuators Shown with MS grip D
Supply voltage: 8÷32 VDC MLT4
Current consumption @ rest: 250 mA C
MLT3
Analog outputs: 5
Output signal range: linear signal (adjustable) B D
0.5÷4.5 V MLT2 MLT4

C
MLT3
0.9÷4.1 V A
MLT1
2.0÷6.0 V B
MLT2
Rated output current: 15 mA A
MLT1
9
Power digital outputs: 4 (0.7 A)
Adjustments: via RS232 serial line 9
AT06-12S
AU AU
OUTPUT SIGNAL CONTROL CURVE
For PC connection (optional) ELECTRONIC

UNITS CALIBRATION TOOL
ordering code: 21.0801.055 Code: 21.0801.055

DATE
Via Malavolti, 36 - 41122 Modena - Italy
+
Tel. +39 059/254895 - Fax +39 059/253512
mail: tecnord@tecnord.com
www.tecnord.com
AT06-4S Code: 21.0801.055 DB9-PF

SOFTWARE
ON CD
ADJUSTABLE PARAMETERS
The following parameters are adjustable via RS232 serial line

by means of a specific calibration and configuration tool.
By use of the configuration window:

• Operation mode.
• Deadman push button enable.
• Joystick functions: axes reverse and enable, virtual cross
movement.
• Assignement for on-off auxiliary outputs.
By use of the calibration window:

• Operating parameters: Vmin, Vmax, Ramp up, Ramp down.
W 42 / 2019
Page JK30
JOYSTICKS
RTM VERSION APPLICATION EXAMPLE
Ratiometric adjustable output signal for closed loop Shown with MS grip D
proportional actuators MLT4
Supply voltage: 8÷32 VDC C
MLT3
Current consumption @ rest: 250 mA
Analog outputs: 5 D
Output signal range: linear signal (adjustable)

B
MLT2 OUT4
MLT4
C
OUT3
MLT3
25÷50÷75% of Vbatt A
MLT1
10÷50÷90% of Vbatt B
OUT2
MLT2
Rated output current: 15 mA A OUT1
MLT1
9
Adjustments: via RS232 serial line 9
AT06-12S
AU AU

ordering code: 21.0801.055 Code: 21.0801.055

DATE
+
Tel. +39 059/254895 - Fax +39 059/253512
www.tecnord.com
AT06-4S Code: 21.0801.055 DB9-PF

SOFTWARE
ON CD

by means of a specific calibration and configuration tool.

• Operation mode.
• Joystick functions: axes reverse and enable, virtual cross
movement.
• Output assignement on-off auxiliary valves.

• Operating parameters: Vmin, Vmax, Ramp up, Ramp down.
W 42/ 2019
Page JK31
JOYSTICKS
PWM VERSION APPLICATION EXAMPLE

D
2 PWM output channels Shown with MS grip MLT4
MLT3
Current consumption @ rest: 250 mA
PWM output: 2 x dual proportional solenoid valves B
Current output range (PWM): 100 to 1600 mA MLT2
(3 A available on request) A
MLT1
Dither frequency: 60 to 250 Hz (100 Hz factory preset)
Adjustable ramp time: 0.05 to 5 s
9
Adjustments: via PC, RS232 serial line connection,
using the Tecnord calibration and
configuration tool (see picture below) AU
Notes:
1) 3rd axis available using FPR-PWM roller switch - Imax = 1.5 A
2) the base height is 60 mm instead of the standard 46 mm
TECNORD ALLEGATO DI PROGETTO M

Date
OUTPUT SIGNAL CONTROL CURVE USER MANUAL
SERVOCOMANDI E
REGOLAZIONE 22/04/16
For PC connection (optional)
CUSTOMER: TECNORD ELECTRONIC
SF.1165.TCN
ordering code:PROJECT:
21.0801.055
JHM – Heavy Duty Multi-Axis Hall Effect Joystick
DATE
2 CONFIGURATION WINDOW Via Malavolti, 36 - 41122 Modena - Italy
+
Tel. +39 059/254895 - Fax +39 059/253512
www.tecnord.com
2.1 Go to “CONFIGURATION WINDOW”

AT06-4S Code: 21.0801.055
Press “CONFIGURATION WINDOW”DB9-PF
button to go to Configuration Window.
SOFTWARE
ON CD
DEAD MAN configuration
 Not Used
CURRENT SETPOI
 Dead Man for X and Y axes
 Minimum Current
 Dead Man for X, Y, Z axes
 Maximum Current
 Alarm Power On
OUTPUT ASSIGN
JOYSTICK FUNCTIONS
 Reverse Axes
 Virtual Cross

by means of the calibration/configuration tool.

• Operation mode.
• Joystick functions: axes reverse, virtual cross movement.
• Current setpoint selection (for 360° movement only).
• Digital directional output signals on both axes (N.O. or N.C. mode)

• Operating parameters: Imin, Imax, Ramp up and Ramp down
times.
OPERATIONAL
WARNING: the specifications/application data shown in our catalogs and data sheets are intended only as a general guide for the product described (herein). MODE
Any specific application should not be undertaken
W 42 / 2019

 2 PROPORT. VALVE BI-DIRECTIONAL (see Par. 2.3.1.1)
 2 PROPORT. VALVE MONO-DIRECTIONAL (see Par. 2.3.1.2)
 1 PROPORT. VALVE MONO-DIRECTIONAL (see Par. 2.3.1.3)
 2 PROPORT. VALVE BIDIRECTIONAL + 2 ON/OFF VALVE (see Par. 2.3.1. 4)
4484 Boeing Drive Rockford, IL 61109 • USA • Phone +1 (815) 397-6628 • Fax +1 (815) 397-2526 Via Malavolti, 36 • 41122 Modena • ITALY VALVE
 2 PROPORT. • PhoneBIDIRECTIONAL
+39 (059) 254895 • Fax +39
+ 4 ON/OFF (059) N.C.
VALVE 253512
(see Par. 2.3.1.5)
mail: delta@delta-power.com • www.delta-power.com mail: tecnord@tecnord.com•2www.tecnord.com
PROPORT. VALVE BIDIRECTIONAL + 4 ON/OFF VALVE N.O. (see Par. 2.3.1.6)
Author: Daniele Ansaloni Page 11 of 26

Page JK32
JOYSTICKS
TCN VERSION (special configuration of PWM version) APPLICATION EXAMPLE

D
1 PWM output in combination with up to 5 on-off outputs Shown with MS grip MLT4
MLT3
Current consumption @ rest: < 250 mA
PWM output: 1 x single proportional solenoid valves B
Current output range (PWM): 100 to 1600 mA (3 A available on request) MLT2
Dither frequency: 60 to 250 Hz (100 Hz factory preset) A
MLT1
Adjustable ramp time: 0.05 to 5 s
9
Adjustments: via PC, RS232 serial line connection,
using the Tecnord calibration and
configuration tool (see picture below)
AU

ordering code: 21.0801.055

DATE
+
Tel. +39 059/254895 - Fax +39 059/253512
www.tecnord.com
AT06-4S Code: 21.0801.055 DB9-PF

SOFTWARE
ON CD
Imin and digital outputs activation: between 2° and 5°
The following parameters are adjustable via RS232 serial line by

means of a specific calibration and configuration tool.

• Operation mode.
• Joystick functions: axes reverse, virtual cross movement.
• Current setpoint selection (for 360° movement only).

• Operating parameters: Imin, Imax, Ramps.
W 42/ 2019
Page JK33
REGOLAZIONE 22/02/14
TECNORD AT.166.TCN
JOYSTICKS
PROJECT: PC SOFTWARE 21.0801.062 TO SET J1939 TECNORD CONFIGURABLE JO
CANBUS VERSION 1 COMPUTER CONNECTION WITH

ADJUSTABLE THE JOYSTICK
PARAMETERS
computer using the 50.2205.229 CAN-USB converter.

Supply voltage: 8÷32 VDC The following parameters are adjustable via CAN:
Current consumption @ rest: < 250 mA For CANopen version
Physical layer: ISO 11898, 250 Kbit/s • Node ID
Protocol:
Connector type:
1.1 Connections J1939/ CANopen
Deutsch DT04-4P For J1939 version
• Node ID
Follow this scheme to connect the joystick to your computer using the 50.2205.229 CAN-US
With CANbus link, following signals can be managed on the In addition, with the specific “Calibration and Configuration PC Tool”
multifunctional grip: and the CAN/USB hardware interface device (see picture below) is
• 4 digital outputs 0.7A (LEDs, detent coils, buzzers, etc). possible:
RD
E
• 6PROJECT
analog voltage
• 6 digital inputs
input 0-5 V (proportional rollers
APPENDIX
(push
MANUAL (Rev.1.00)
buttons, toggles,
Date
MAN and mini-joysticks).
etc).
22/02/14
Page 3 of 18
• Read joystick configuration
• Adjiust X, Y axles sensibility and direction PC
• Enable /disable digital or analog inputs and digital outputs
JOYSTICK
AT.166.TCN
• Change Node ID
FTWARE 21.0801.062 TO SET J1939 TECNORD CONFIGURABLE JOYSTICK
ER CONNECTION WITH THE JOYSTICK

SOFTWARE PC SOFT
ons FOR J1939 VERSION ONLY
to connect the joystick to your computer using the 50.2205.229 CAN-USB converter.
PC POWER SUPPLY
SOFTWARE PC
PLY POWER SUPPLY
D D
MLT4 MLT4
C C
MLT3 MLT3
B B
MLT2 MLT2
A A
MLT1 MLT1
9 9
TECNORD PROJECT APPENDIX MAN TECNORD PROJECT APPENDIX MAN
SERVOCOMANDI E MANUAL (Rev.1.00) Date SERVOCOMANDI E MANUAL (Rev.1.00) Date
Page 3 of 18 Page 3 of 18
REGOLAZIONE 22/02/14 REGOLAZIONE 22/02/14
TECNORD AT.166.TCN TECNORD AT.166.TCN
PROJECT: PC SOFTWARE 21.0801.062 TO SET J1939 TECNORD CONFIGURABLE JOYSTICK PROJECT: PC SOFTWARE 21.0801.062 TO SET J1939 TECNORD CONFIGURABLE JOYSTICK
AU 1 COMPUTER CONNECTION WITH THE JOYSTICK AU 1 COMPUTER CONNECTION WITH THE JOYSTICK
1.1 Connections 1.1 Connections

CAN-USB CONVERTER
Follow this scheme to connect the joystick to your computer using the 50.2205.229 CAN-USB converter. Follow this scheme to connect the joystick to your computer using the 50.2205.229 CAN-USB converter.
JOYSTICK PC JOYSTICK PC
SOFTWARE PC SOFTWARE PC
CANOPEN VERSION ONLY J1939 VERSION ONLY

2 x 120  resistors (in parallel) in order to terminate CAN line, otherwise CAN
POWER SUPPLY POWER SUPPLY
ordering code: 21.0801.071 ordering code: 21.0801.062

ELECTRONIC
work correctly.
DATE
AT06-4S Code: 21.0801.055

+ AT06-4S Code: 21.0801.055
+ + Via Malavolti, 36 - 41122 Modena - Italy
Tel. +39 059/254895 - Fax +39 059/253512
www.tecnord.com
DB9-PF DB9-PF
CAN-USB CONVERTER CAN-USB CONVERTER
SOFTWARE
NOTE:
Remember to put 2 x 120  resistors (in parallel) in order to terminate CAN line, otherwise CAN
NOTE:
Remember to put 2 x 120  resistors (in parallel) in order to terminate CAN line, otherwise CAN ON CD
communication not work correctly.
CAN-USB CONVERTER communication not work correctly.
Date of last print:

W 42 / 2019
24/02/2016 18:02:00
Author: Daniele Ansaloni
Date of last print:
24/02/2016 18:02:00
Date of last print:
24/02/2016 18:02:00
Author: Daniele Ansaloni
NOTE:
Remember to put 2 x 120  resistors

(in parallel) in order to terminate CAN line,
Page JK34 communication not work correctly.
JOYSTICKS
JOYSTICKS
JHM Heavy Duty Multi-Axis Hall Effect Joystick JOYSTICKS
JOYSTICKS
JOYSTICKS
JHM Heavy Duty Multi-Axis Hall Effect Joystick
JHM HEAVY DUTY
JHM MULTI-AXIS HALL
joystick with EFFECT
grips JOYSTICK
- configuration examples with overall dimensions
JHM
JHM Heavy Duty
Heavy Duty Multi-Axis
Multi-Axis Hall
Hall Effect
Effect Joystick
Joystick
JHM joystick with grips - configuration examples with overall dimensions
JHM joystick
JHM joystick with
with grips
grips -- configuration
configuration examples
examples with
with overall
overall dimensions
22° dimensions
22°
22° 22°
JHM base with IL handle JHM base with IC handle

Complete
JHM base code: JHM-L4D/ANH-IL 0000
with IL handle Complete
JHM base code: JHM-L4D/ANH-IC 0200
with IC handle
JHM base
JHM base with
with IL
IL handle
handle
JHM base with IL handle JHM base
JHM base with
with IC
IC JHM
handle
base with IC handle
handle
Complete code: JHM-L4D/ANH-IL
Complete
Complete code:
Complete
code:
00000000
JHM-L4D/ANH-IL 0000
code: JHM-L4D/ANH-IL
JHM-L4D/ANH-IL 0000 Complete code:
Complete
Complete code:JHM-L4D/ANH-IC
JHM-L4D/ANH-IC
Complete
code:
0200 0200
0200
code: JHM-L4D/ANH-IC
JHM-L4D/ANH-IC 0200
22° 22° 22° 22°
JHM base with IE type handle JHM base with IE type handle
JHM base
JHM baseComplete
with IE
with IE type
type handle
code: JHM-L4D/ANH-IE A4P9 0000
handle JMF base
JMF base with IE
Complete IEcode:
type JHM-L4D/ANH-IE
handle A1P9 1PRS
JHM base
Complete withJHM-L4D/ANH-IE
code: IE type handle A4P9 0000 JMFwith
Complete
type
with handle
baseJHM-L4D/ANH-IE
code: IE type handle
A1P9 1PRS
Complete code: JHM-L4D/ANH-IE A4P9 0000 Complete code: JHM-L4D/ANH-IE A1P9 1PRS
Complete
JHM base with IE type code: JHM-L4D/ANH-IE A4P9 0000
handle JMF base Complete
with IE type code: JHM-L4D/ANH-IE A1P9 1PRS
handle
Complete code: JHM-L4D/ANH-IE A4P9 0000 Complete code: JHM-L4D/ANH-IE A1P9 1PRS
W 42/ 2019
WARNING: The
WARNING: The specifi
cations/application data shown shown in in our
our catalogs
catalogs and
and data
data sheets
sheets are
are intended
intended only
only as
as aa general
general guide
guide forfor the
the product
product described
described
without independent study, evaluation, and testing data
for suitability.
(herein).
WARNING:
(herein). Any specifi
Any specifi
cc application
application
The specifi should not
cations/application
should not bebedataundertaken
undertaken without
shownwithout independent
in our catalogs study,
andstudy,
independent evaluation,
data sheets and testing
testing
are intended
evaluation, and for suitability.
only
for suitability.
as a general guide for the product described
(herein). Any specific application should not be undertaken without independent study, evaluation, and testing for suitability.
WARNING: The specifications/application data shown Phonein +39
our catalogs
059 254895
254895and data sheets
+39are
059intended
253512 only as a general guide for the product described
(herein). Any specifi c application should not be undertaken Phone +39 059
without •• Fax
independent
Fax +39
study, 059 253512
evaluation, and•• testing
E-mail:
E-mail: tecnord@tecnord.com
tecnord@tecnord.com
for suitability.
Phone +39 059 254895 JOYSTICKS
• Fax +39
JOYSTICKS page 32253512 • E-mail: tecnord@tecnord.com
059
-- page 32
JOYSTICKS - page 32 Page JK35
JOYSTICKS - page 32
JOYSTICKS
JHM HEAVY DUTY MULTI-AXIS HALL EFFECT JOYSTICK
22° 22° 22° 22°

22°
22°
22° 22°
JHM base with MS type handle JHM base with MS type handle
Complete code: JHM L4D/ANH-MS A6P9 R3P9 Complete code: JHM L4D/ANH-MS A2P9 2FPR R1P9
22° 22°
22° 22°
22° 22° 22° 22°
JHM base with MG type handle JHM base with MG type handle
Complete code: JHM L4D/ANH-MG A4P9 R1P9 Complete code: JHM L4D/ANH-MG A2P9 1FPR 0000
W 42 / 2019
Page JK36
JOYSTICKS
JHM HEAVY DUTY MULTI-AXIS HALL EFFECT JOYSTICK
HR joystick with grips - configuration examples with overall dimensions
22° 22°
JHM base with HL type handle JHM base with HL type handle
Complete code: JHM-L4D/ANH-HL-04P9-2P9/RDFF Complete code: JHM-L4D/ANH-HL-04P9-2P9/RDFF
22° 22°
JHM base with HR type handle JHM base with HR type handle
Complete code: JHM-L4C/NN-HR-0FPR-2P9/R000 Complete code: JHM-L4C/NN-HR-0FPR-2P9/R000
W 42/ 2019
Page JK37
JOYSTICKS
ERGONOMIC GRIPS
IL cylindrical knob
JK39 JK43
IC cylindrical
IE ergonomic, gear type, multi-functions JK39 JK44
HL multi-function ergonomic left hand grip JK40 JK45
HR multi-function ergonomic right hand grip JK40 JK47
MS ergonomic, symmetric, multi-functions JK41 JK49
MG ergonomic, right hand, multi-functions JK42 JK52
Note: 1) Ergonomic grips can be used as stand alone devices.

2) Grips do not include rubber gaiter and retainer ring, which must be ordered separately.
W 42 / 2019
Page JK38
JOYSTICKS
IL / IC / IE GRIPS ORDERING INFORMATION
IL /
Type of grip Push buttons on grip

IL Cylindrical knob 0000 No push button
0100 Top normally open push button
IC /
Type of grip Push buttons on grip

IC Cylindrical grip 0000 No push button
0100 Top normally open push button
0200 Top rocker switch
On-off Analog
controls on rear controls on rear
plate plate
IE / /
Type of grip Dead Man PB On-Off Controls Analog Control

IE Ergonomic 0 No dead man (P9 up to 3 A inductive) 000 No control
A Right side 000 No push button 1FPR One Proportional roller switch
Dead man PB 1P9 One push button (horizontally position)
*Note: Red colour 2P9 Two push button
P9 - P9L B Left side 3P9 Three push button
See page “Technical Dead man PB
Information”. Red colour
Other configuration
on request.
W 42/ 2019
Page JK39
JOYSTICKS
HL / HR ERGONOMIC GRIP ORDERING INFORMATION
On-off controls On-off controls On-off controls

analog control on analog control on analog control on
front plate down plate rear plate
HL / - / R -
Type of grip Dead Man PB Connector type

HL Multi-function 0 No dead man
3 Flying leads
Ergonomic 25 cm length
Left Hand Grip On-Off Controls On-Off Controls On-Off Controls 4 Male connector,
(P9 up to 3 A inductive) (P9 up to 3 A inductive) (P9 up to 3 A inductive) 12 poles,
*Note: 000 No push button 000 No push button 000 No push button Deutsch DT04-12P,
25 cm cable length
DFF - K1 - P9 - P9L 1P9 One push button 1P9 One push button 1P9 One push button
See page “Technical 2P9 Two push button 2P9 Two push button 2P9 Two push button 5 Male connector,
Information”. 4 poles,
3P9 Three push button DFF One Rocker Switch
Deutsch DT04-4P,
Other configuration on request. 4P9 Four push button 1K1 One Rocker Switch 25 cm cable length
1K1 One Rocker Switch
6 Male connector,
6 poles,
Deutsch DT04-6P,
Analog Control
25 cm cable length
Analog Control 000 No control
000 No control 7 Male connector,
FPR Proportional roller switch
8 poles,
FPR Proportional roller switch Deutsch DT04-8P,
25 cm cable length
On-off controls On-off controls On-off controls

analog control on analog control on analog control on
front plate down plate rear plate
HR / - / R -
Type of grip Dead Man PB Connector type

HR Multi-function 0 No dead man
3 Flying leads
Ergonomic 25 cm length
Right Hand Grip On-Off Controls On-Off Controls On-Off Controls 4 Male connector,
(P9 up to 3 A inductive) (P9 up to 3 A inductive) (P9 up to 3 A inductive) 12 poles,
*Note: 000 No push button 000 No push button 000 No push button Deutsch DT04-12P,
25 cm cable length
DFF - K1 - P9 - P9L 1P9 One push button 1P9 One push button 1P9 One push button
See page “Technical 2P9 Two push button 2P9 Two push button 2P9 Two push button 5 Male connector,
3P9 Three push button DFF One Rocker Switch
Deutsch DT04-4P,
Other configuration on request. 4P9 Four push button 1K1 One Rocker Switch 25 cm cable length
1K1 One Rocker Switch
6 Male connector,
6 poles,
Deutsch DT04-6P,
Analog Control
25 cm cable length
Analog Control 000 No control
000 No control 7 Male connector,
FPR Proportional roller switch
8 poles,
FPR Proportional roller switch Deutsch DT04-8P,
25 cm cable length
W 42 / 2019
Page JK40
JOYSTICKS
MS ERGONOMIC SYMMETRIC GRIP ORDERING INFORMATION
On-off Analog On-off & analog

controls on front controls on front controls
plate plate on rear plate
MS / - / R -
Type of grip Dead Man PB On-Off Controls Connector type

MS Multi-function 0 No dead man (P9 up to 3 A inductive)
3 Flying leads
ergonomic symmetric A Dead man PB 000 No push button 25 cm length
1P9 One push button
4 Male connector,
2P9 Two push button 12 poles,
*Note: 3P9 Three push button Deutsch DT04-12P,
1K1 One Rocker Switch 25 cm cable length
DFF - K1 - P9 - P9L
See page “Technical On-Off Controls Analog Control 5 Male connector,
Information”. Analog Control 4 poles,
(P9 up to 3 A inductive) 000 No control Deutsch DT04-4P,
Other configuration on request. 000 No push button 1FPR One Proportional roller switch 000 No control 25 cm cable length
1P9 One push button 2FPR Two Proportional roller switch 1FPR One Proportional roller
6 Male connector,
2P9 Two push button 3FPR Three Proportional roller switch switch 6 poles,
3P9 Three push button Deutsch DT04-6P,
OPTIONS
25 cm cable length
4P9 Four push button 1FPR-1PWM
5P9 Five push button 7 Male connector,
Proportional roller and built-in PWM driver
8 poles,
6P9 Six push button for a bidirectional dual proportional coil Deutsch DT04-8P,
7P9 Seven push button 2FPR-2PWM 25 cm cable length
1K1 One Rocker Switch Proportional roller and built-in PWM driver
2K1 Two Rocker Switch for 2 bidirectional dual proportional coil
DFF One Rocker Switch
W 42/ 2019
Page JK41
JOYSTICKS
MG ERGONOMIC GRIP ORDERING INFORMATION
On-off Analog On-off & analog

controls on front controls on front controls
plate plate on rear plate
MG / - / R -
Type of grip Dead Man PB On-Off Controls Connector type

MG Ergonomic 0 No dead man (P9 up to 3 A inductive)
3 Flying leads
right hand A Dead man PB 000 No push button 25 cm length
1P9 One push button
4 Male connector,
2P9 Two push button 12 poles,
*Note: Deutsch DT04-12P,
Analog Control 25 cm cable length
DFF - K1 - P9 - P9L
See page “Technical On-Off Controls Analog Control 000 No control 5 Male connector,
(P9 up to 3 A inductive) 000 No control Deutsch DT04-4P,
Other configuration on request. 000 No push button 1FPR One Proportional roller switch 25 cm cable length
1P9 One push button 2FPR Two Proportional roller switch 6 Male connector,
2P9 Two push button OPTIONS 6 poles,
3P9 Three push button Deutsch DT04-6P,
1FPR-1PWM
25 cm cable length
4P9 Four push button Proportional roller and built-in PWM driver
5P9 Five push button 7 Male connector,
for a bidirectional dual proportional coil
8 poles,
6P9 Six push button 2FPR-2PWM Deutsch DT04-8P,
1K1 One Rocker Switch Proportional roller and built-in PWM driver 25 cm cable length
2K1 Two Rocker Switch for 2 bidirectional dual proportional coil
DFF One Rocker Switch
W 42 / 2019
Page JK42
JOYSTICKS
IL - IC GRIPS
IL - CYLINDRICAL KNOB IC - CYLINDRICAL GRIP
MECHANICAL SPECIFICATIONS MECHANICAL SPECIFICATIONS
Body material: Thermoplastic elastomer Body material: nylon

Colour: black Bottom rubber material: neoprene
Operating temperature range: -20°C / +60°C Colour: black
Connecting hub: female thread / M14 x 1.5 Operating temperature range: -20°C / +60°C
Connecting hub: female thread / M14 x 1.5
ELECTRICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS
Prewired exit cable: 250 mm Prewired exit cable: 250 mm

Insulating cable material: PVC Insulating cable material: PVC
TOP PUSH BUTTON PUSH BUTTON AND ROCKER SWITCH
Rated amperage: 3 A inductive Contacts: silver plated

Life: > 100.000 cycles Rated amperage: 16 A / 250 vac
Protection class: IP 64 3 A / 24 VDC
Electrical life: > 100.000 cycles
Mechanical life: > 3.000.000 cycles
OVERALL DIMENSIONS OVERALL DIMENSIONS
ø 33
ø 33
46
46
55
18
M14x1,5
IL-0000 IL-0100 IC-0000 IC-0100 IC-0200

No push button Top push button No push button Top push button Top rocker switch
(No circuit) (No circuit)
IL - IC ORDERING INFORMATION: see page JK39
W 42/ 2019
Page JK43
JOYSTICKS
IE MULTI-FUNCTION ERGONOMIC GRIP
FEATURES
• Multi-functions ergonomic grip gear type with on-off and proportional
switches.
• Easy adaptability to existing joystick control lever.
Material: thermoplastic
Colour: black
Protection class: IP 65 (plain grip)
Prewired exit cable: 250 mm

Available push buttons and switches
P9 - P9L - Push buttons: see page JK61
Technical Information
A - Side dead man push button: see above specifications
for P9 push button
FPR - Proportional roller: see FPR data sheet
Output signal: 3-pins connection
hall effect contactless sensor
OVERALL DIMENSIONS CONFIGURATION EXAMPLES
D-man P/B Rear P/B Rear FPR

IE/0000/0000 0 0 0
IE/A000/0000 yes 0 0
IE/A1P9/0000 yes 1xP9 0
IE/A2P9/0000 yes 2xP9 0
IE/A3P9/0000 yes 3xP9 0
IE/0000/1FPR 0 0 1xFPR
IE-A1P9-1FPR yes 1xP9 1xFPR
IE ORDERING INFORMATION: see page JK39
W 42 / 2019
Page JK44
JOYSTICKS
HL MULTI-FUNCTION ERGONOMIC LEFT HAND GRIP
FEATURES
• Optimum ergonomic design.
• High perfomance switches.
Colour: black
Protection class: IP 65 with plain grip
(IP 67 with special assembly
on request)

DFF - Rocker Switch: see page JK60 Technical Info
K1 - Rocker Switch: see page JK60 Technical Info
P9 - P9L - Push buttons: see page JK61 Technical Info
FRONT VIEW - LEFT HAND
Mod. FRONT P/B BOTTOM P/B REAR P/B

HL/04P9-2P9/RDFF
HL/0000-000/R000 0 0 0
HL/01P9-000/R000 1xP9 0 0
HL/02P9-000/R000 2xP9 0 0
HL/03P9-000/R000 3xP9 0 0
HL/04P9-000/R000 4xP9 0 0
HL/04P9-1P9/R000 4xP9 1xP9 0
HL/04P9-2P9/R000 4xP9 2xP9 0
HL/04P9-2P9/R1P9 4xP9 2xP9 1xP9
HL/04P9-2P9/R2P9 4xP9 2xP9 2xP9
HL/0FPR-000/R000 1xFPR 0 0
HL/0000-000/RFPR 0 0 1xFPR
HL/0FPR-000/RFPR 1xFPR 0 1xFPR
HL/01K1-000/R000 1xK1 0 0
HL/0000-000/R1K1 0 0 1xK1
HL/01K1-000/R1K1 1xK1 0 1xK1
HL/0DFF-000/R000 1xDFF 0 0
HL/0000-000/RDFF 0 0 1xDFF
HL ORDERING INFORMATION: see page JK40 HL/0DFF-000/RDFF 1xDFF 0 1xDFF
W 42/ 2019
Page JK45
JOYSTICKS
HL MULTI-FUNCTION ERGONOMIC LEFT HAND GRIP
FEATURES
Colour: black
on request)

FPR - Proportional roller: see FPR data sheet REAR VIEW - LEFT HAND

HL/04P9-2P9/RDFF
HL/0000-000/R000 0 0 0
HL/0FPR-000/R000 1xFPR 0 0
HL/0FPR-1P9/R000 1xFPR 1xP9 0
HL/0FPR-2P9/R000 1xFPR 2xP9 0
HL/0FPR-2P9/R1P9 1xFPR 2xP9 1xP9
HL/0FPR-2P9/R2P9 1xFPR 2xP9 2xP9
HL/0FPR-000/R1FPR 1xFPR 0 1xFPR
HL/0FPR-1P9/R1FPR 1xFPR 1xP9 1xFPR
HL/0FPR-2P9/R1FPR 1xFPR 2xP9 1xFPR
W 42 / 2019
Page JK46
JOYSTICKS
HR MULTI-FUNCTION ERGONOMIC RIGHT HAND GRIP
FEATURES
Colour: black
on request)

FPR - Proportional roller: see FPR data sheet FRONT VIEW - RIGHT HAND

HR/0FPR-2P9/R000
HR/0000-000/R000 0 0 0
HR/01P9-000/R000 1xP9 0 0
HR/02P9-000/R000 2xP9 0 0
HR/03P9-000/R000 3xP9 0 0
HR/04P9-000/R000 4xP9 0 0
HR/04P9-1P9/R000 4xP9 1xP9 0
HR/04P9-2P9/R000 4xP9 2xP9 0
HR/04P9-2P9/R1P9 4xP9 2xP9 1xP9
HR/04P9-2P9/R2P9 4xP9 2xP9 2xP9
HR/0FPR-000/R000 1xFPR 0 0
HR/0000-000/RFPR 0 0 1xFPR
HR/0FPR-000/RFPR 1xFPR 0 1xFPR
HR/01K1-000/R000 1xK1 0 0
HR/0000-000/R1K1 0 0 1xK1
HR/01K1-000/R1K1 1xK1 0 1xK1
HR/0DFF-000/R000 1xDFF 0 0
HR/0000-000/RDFF 0 0 1xDFF
HR ORDERING INFORMATION: see page JK40 HR/0DFF-000/RDFF 1xDFF 0 1xDFF
W 42/ 2019
Page JK47
JOYSTICKS
HR MULTI-FUNCTION ERGONOMIC RIGHT HAND GRIP
FEATURES
Colour: black
on request)

FPR - Proportional roller: see FPR data sheet REAR VIEW - RIGHT HAND

HR/0FPR-2P9/R000
HR/0000-000/R000 0 0 0
HR/0FPR-000/R000 1xFPR 0 0
HR/0FPR-1P9/R000 1xFPR 1xP9 0
HR/0FPR-2P9/R000 1xFPR 2xP9 0
HR/0FPR-2P9/R1P9 1xFPR 2xP9 1xP9
HR/0FPR-2P9/R2P9 1xFPR 2xP9 2xP9
HR/0FPR-000/R1FPR 1xFPR 0 1xFPR
HR/0FPR-1P9/R1FPR 1xFPR 1xP9 1xFPR
HR/0FPR-2P9/R1FPR 1xFPR 2xP9 1xFPR
W 42 / 2019
Page JK48
JOYSTICKS
MS MULTI-FUNCTION ERGONOMIC SYMMETRIC GRIP
FEATURES
Colour: black
on request) IP 54 with
dead man trigger option

A - Dead man push button
Rated amperage: up to 3 A inductive
Protection class (microswitch): IP 67
Mod. D-man P/B Front P/B Rear P/B

MS-A6P9-R3P9
MS/0000/0000 0 0
MS/A000/0000/0000 yes 0
MS/A1P9/0000/0000 yes 1xP9
MS/A2P9/0000/0000 yes 2xP9
MS/A3P9/0000/0000 yes 3xP9
MS/A4P9/0000/0000 yes 4xP9
MS/A5P9/0000/0000 yes 5xP9
MS/A6P9/0000/0000 yes 6xP9
MS/A6P9/0000/R1P9 yes 6xP9 1xP9
MS ORDERING INFORMATION: see page JK41
W 42/ 2019
Page JK49
JOYSTICKS
FEATURES
Colour: black

Mod. D-man Front Front Rear Rear

MS-A2P9-2FPR-F1P9 P/B P/B FPR P/B FPR
MS/01P9/1FPR/0000 0 1xP9 1xFPR
MS/A2P9/1FPR/0000 yes 2xP9 1xFPR
MS/A3P9/1FPR/R1P9 yes 3xP9 1xFPR 1xP9
MS/A4P9/1FPR/F1P9 yes 4xP9 1xFPR 1xP9 1xFPR
MS/A2P9/2FPR/0000 yes 2xP9 2xFPR 0
MS/A000/3FPR/0000 yes 0 3xFPR 0
MS/A000/3FPR/R1P9 yes 0 3xFPR 1xP9
MS/A000/3FPR/R2P9 yes 0 3xFPR 2xP9
W 42 / 2019
Page JK50
JOYSTICKS
FEATURES
• Internal PWM driver.
Colour: black

PWM - Pulse width modulated output current driver
OVERALL DIMENSIONS
for a dual coil proportional valve
Mod. Supply voltage: 8-32 Volt
MS-A2P9-1FPR-1PWM
Max. current draw: 100 mA
Current output range: factory set btw 0 and 1500 mA
CONFIGURATION EXAMPLES
D-man P/B Front P/B Front FPR

MS/01P9/1FPR/1PWM 0 1xP9 1xFPR
MS/A2P9/1FPR/1PWM yes 2xP9 1xFPR
W 42/ 2019
Page JK51
JOYSTICKS
MG MULTI-FUNCTION ERGONOMIC RIGHT HAND GRIP
FEATURES
Colour: black

Mod. D-man P/B Front P/B Rear P/B

MG-A6P9-R3P9
MG/0000/0000 0 0
MG/A000/0000/0000 yes 0
MG/A1P9/0000/0000 yes 1xP9
MG/A2P9/0000/0000 yes 2xP9
MG/A3P9/0000/0000 yes 3xP9
MG/A4P9/0000/0000 yes 4xP9
MG/A5P9/0000/0000 yes 5xP9
MG/A6P9/0000/0000 yes 6xP9
MG/A6P9/0000/R1P9 yes 6xP9 1xP9
MG ORDERING INFORMATION: see page JK42
W 42 / 2019
Page JK52
JOYSTICKS
FEATURES
Colour: black

Mod. D-man Front Front Rear Rear

MG-A000-3FPR P/B P/B FPR P/B FPR
MG/01P9/1FPR/0000 0 1xP9 1xFPR
MG/A2P9/1FPR/0000 yes 2xP9 1xFPR
MG/A3P9/1FPR/R1P9 yes 3xP9 1xFPR 1xP9
MG/A2P9/2FPR/0000 yes 2xP9 2xFPR 0
MG/A000/3FPR/0000 yes 0 3xFPR 0
MG/A000/3FPR/R1P9 yes 0 3xFPR 1xP9
MG/A000/3FPR/R2P9 yes 0 3xFPR 2xP9
W 42/ 2019
Page JK53
JOYSTICKS
FEATURES
• Internal PWM driver.
Colour: black

PWM - Pulse width modulated output current driver
OVERALL DIMENSIONS for a dual coil proportional valve
Mod. Supply voltage: 8-32 Volt
MG-A4P9-1FPR-1PWM
Max. current draw: 100 mA
Current output range: factory set btw 0 and 1500 mA
CONFIGURATION EXAMPLES
D-man Front Front Rear

PWM
P/B P/B FPR P/B
MG/01P9/1FPR/1PWM 0 1xP9 1xFPR 1xPWM
MG/A2P9/1FPR/1PWM yes 2xP9 1xFPR 1xPWM
MG/A4P9/1FPR/1PWM/R1P9 yes 4xP9 1xFPR 1xPWM 1xP9
MG/A4P9/1FPR/1PWM/R2P9 yes 4xP9 1xFPR 1xPWM 2xP9
W 42 / 2019
Page JK54
JOYSTICKS
ACCESSORIES
MODEL DESCRIPTION PAGE
Joystick connections Connector kits JK56
Joystick calibration tool Software calibration tool linking cables JK58
Technical informations
Rocker switches, push buttons knob potentiometer JK60
Operators for Grip Assembling
W 42 / 2019
Page JK55
JOYSTICKS
CONNECTOR KITS
7 POLES DUBOX CONNECTOR
Kit includes: male connector, female contacts

Available for joystick: JLP-L2S
ORDERING CODE: 13.0310.046
7 POLES C-GRID CONNECTOR

Available for joystick: JLP-L2S, FTH
7 POLES DUBOX CONNECTOR WITH WIRES
Kit includes: male connector, with inserted wires section 0.22 mm²
Available for joystick: JLP-L2S
3 wires 80 cm length ORDERING CODE: 13.0310.206

7 wires 150 cm length ORDERING CODE: 13.0310.313
4 POLES MINIFIT CONNECTOR

Available for joystick: FPR
6 POLES MINIFIT CONNECTOR

Available for joystick: FPR-PWM
W 42 / 2019
Page JK56
JOYSTICKS
CONNECTOR KITS
3 POLES DEUTSCH DT06-3S
Kit includes: male connector, female contacts, secondary lock

Available for joystick: FPR
Kit includes: male connector, female contacts, secondary lock

Available for joystick: JHM-CAN
Kit includes: male connector, female contacts, secondary lock and fillers
Available for joystick: JHM
W 42 / 2019
Page JK57
JOYSTICKS
CALIBRATION TOOL
TECNORD SOFTWARE JOYSTICK CALIBRATION TOOL

Tecnord joysticks, with electronic control unit inside, are supplied with operation parameters standard programming, which satisfies most
applications. For special application SCT calibration software allows some of the parameters for proportional solenoid valve control to be
modified via computer; for example the minimum and maximum current or ramp up and ramp down parameters may be defined. The linking
cable shown in the following page (optional, to be ordered separately) is necessary for the computer connection.
ELECTRONIC
DATE

Tel. +39 059/254895 - Fax +39 059/253512
www.tecnord.com
SOFTWARE
INSTALLATION
MINIMUM SYSTEM REQUIREMENTS

• Windows XP® operating system or higher.
• Intel® Pentium processor.
• 32 Mb RAM.
• CD player unit.
• Connecting through a standard RS232 serial port, DB9 connection; alternatively, a USB-RS232 converter can be used.
PROGRAM INSTALLATION
To install the SCT software onto a personal computer, simply execute the file setup.exe.
W 42 / 2019
Page JK58
JOYSTICKS
CALIBRATION LINKING CABLES
JHM-PWM, JHM-MLT - SOFTWARE CALIBRATION TOOL

ELECTRONIC
With Deutsch-DB9 linking cable. DATE
Available for joystiks: JHM-PWM, JHM-MLT

Tel. +39 059/254895 - Fax +39 059/253512
www.tecnord.com
RS232 - USB CONVERTER
It allows Tecnord joysticks to Personal Computer connection when the latter is unprovided
of serial port; for installation follow the instruction enclosed with the converter
CAN - USB CONVERTER
It allows Tecnord CAN joysticks to Personal Computer connection with a USB port;
for installation follow the instruction enclosed with the interface device
CAN - USB CONVERTER WITH DEUTSCH-DB9 LINKING CABLE
It allows Tecnord CAN joysticks to Personal Computer connection with a USB port;
for installation follow the instruction enclosed with the interface device
CAN J1939 - SOFTWARE CALIBRATION TOOL

ELECTRONIC
DATE
With CAN-USB converter and Deutsch-DB9 linking cable. It allows modification

of specific parameters on Tecnord CAN joysticks following calibration tool program
Tel. +39 059/254895 - Fax +39 059/253512
www.tecnord.com
on CD Rom; for installation follow the instruction enclosed with the interface device
W 42 / 2019
Page JK59
JOYSTICKS
TECHNICAL INFORMATIONS - OPERATORS FOR GRIP ASSEMBLING
DFF - ROCKER SWITCH TYPE

Switch Operation: On-Off-On
Ordering code: 50.1301.500
Characteristics
Inrush current (capacitive) 16A 250 VAC (contact pair Ag / Cu and basic type 1838)
Contact resistance (new condition) < 100 mOhm (1 A 12 VDC)
Insulation resistance (new condition) > 100 mOhm (500 VDC)
Protection type IP67 1E6 mechanical life endurance
Ambient temperature terminal side -20°C/+105°C
actuating side -20°C/+55°C
K1 - ROCKER SWITCH TYPE

Switch Operation: Ordering code:
On-Off-On 50.1301.501
On-Off 50.1301.502
Mom-Off-Mom 50.1301.503
Fwd-Neu-Rev 50.1301.504
Characteristics
Load 28 VDC or 125/250 VAC, 60Hz Cycles
Resistive 10A 50.000
Inductive 10A 25.000
Mechanical life 100.000 cycles

Seal IP68S
Operating temp. range -30°C to +85°C
Materials Thermoplastic
W 42 / 2019
Page JK60
JOYSTICKS
P9 - PUSH BUTTONS
Switch Operation: On-Off

Case Flush Color Ordering code Characteristics
Red 13.0310.549 Operational life up to 1.000.000 cycles
Blue 13.0310.551 Rated amperage up to 5 A resistive
Yellow 13.0310.535 up to 3 A inductive
Black 13.0310.555 Protection class IP 64 (IP 68S available)
Green 13.0310.553 Operating temp. range -40°C to +85°C
White 13.0310.547 Button and bezel material thermoplastic
Purple 13.0310.559 Contacts gold plated silver alloy
Grey 13.0310.561
Orange 13.0310.557
Case Raised Color Ordering code Characteristics

Red 13.0310.550 Operational life up to 1.000.000 cycles
Blue 13.0310.552 Rated amperage up to 5 A resistive
Yellow 13.0310.528 up to 3 A inductive
Black 13.0310.556 Protection class IP 64 (IP 68S available)
Green 13.0310.554 Operating temp. range -40°C to +85°C
White 13.0310.548 Button and bezel material thermoplastic
Purple 13.0310.560 Contacts gold plated silver alloy
Grey 13.0310.562
Orange 13.0310.558
P9L - PUSH BUTTONS WITH LED (12 VDC)

Switch Operation: On-Off
Case Flush Color Led Ordering code Characteristics

Green Green 50.1301.328 Operational life up to 1.000.000 cycles
Red Red 50.1301.329 Rated amperage up to 5 A resistive
Orange Amber 50.1301.330 at 28VDC
Yellow White 50.1301.331 Protection class IP67 (70.000 cycles)
Blue Blue 50.1301.332 Operating temp. range -40°C to +85°C
White Red 50.1301.348 Button and bezel material thermoplastic
Black Red 50.1301.345 Contacts gold plated silver
Case Raised Color Led Ordering code

Green Green 50.1301.324
Red Red 50.1301.325
W 42 / 2019
Page JK61
JOYSTICKS
APL - LATCHING PUSH BUTTONS

Switch Operation: On-Off Latching
Case Color Led Ordering code Characteristics

Red X 50.1301.407 Operational life up to 1.000.000 cycles
Red Red 50.1301.414 Rated amperage up to 5 A resistive
Yellow Red 50.1301.415 up to 3 A inductive
Yellow X 50.1301.416 Protection class IP 67
Green X 50.1301.417 Operating temp. range -40°C to +85°C
Button and bezel material polyamide 6/6
Contacts gold plated silver
SEALING BOOTS
For raised dome
SEALING BOOTS
For flush dome
KNOB POTENTIOMETER TYPE P16
Ohmic value: 4.7kΩ ±20°

Electrical travel: 270° ±10°
KNOB POTENTIOMETER TYPE P16
Ohmic value: 10kΩ ±20°

Electrical travel: 270° ±10°
W 42 / 2019
Page JK62

Joysticks Catalogue

Uploaded by

Copyright:

Available Formats

Joysticks Catalogue

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Joysticks Catalogue

Uploaded by

Copyright:

Available Formats

JOYSTICKS

JOYSTICKS AND GRIPS

Section / Description page

FINGERTIP PROPORTIONAL CONTROL LEVERS AND SWITCHES.................................................................. JK3

HEAVY DUTY MULTI-AXIS JOYSTICKS................................................................................................................ JK19

ERGONOMIC GRIPS .............................................................................................................................................. JK38

ACCESSORIES ...................................................................................................................................................... JK55

without independent study, evaluation, and testing for suitability.

without independent study, evaluation, and testing for suitability.

FINGERTIP PROPORTIONAL CONTROL LEVERS AND SWITCHES

DESCRIPTION ORDERING INFORMATION PAGE TECHNICAL INFORMATION PAGE

FTC proportional control lever JK4 JK9

FTH contactless proportional control lever JK5 JK12

JLP proportional control lever JK6 JK14

FPR proportional roller switch JK7 JK16

FPR - PWM proportional roller switch JK7 JK17

JMT proportional multi-axis JK8 JK18

without independent study, evaluation, and testing for suitability.

FTC PROPORTIONAL CONTROL LEVER ORDERING INFORMATION

B Pot & Center switch

(AMP p/n 280610/1)

Z Pot & Bidirect. 2 8 poles electronic board on pot.

E Pot & Center switch

F Pot & Bidirect. switches

W Pot & Bidirect.

H Pot & Center switch

I Pot & Bidirect. switches

R Pot & Bidirect.

M Pot & Center switch

N Pot & Bidirect. switches

X Pot & Bidirect.

without independent study, evaluation, and testing for suitability.

FTH CONTACTLESS PROPORTIONAL CONTROL LEVER ORDERING INFORMATION

without independent study, evaluation, and testing for suitability.

JLP PROPORTIONAL CONTROL LEVER ORDERING INFORMATION

Q Pot & bidirect. switches E 4 pins Amp J. male connector

G 7 pins molex C-Grid/SL male

R Pot & bidirect. switches

C Pot & bidirect. switches

without independent study, evaluation, and testing for suitability.

FPR FINGERTIP PROPORTIONAL SWITCHES ORDERING INFORMATION

without independent study, evaluation, and testing for suitability.

JMT PROPORTIONAL MULTI-AXIS HALL EFFECT THUMB JOYSTICK

without independent study, evaluation, and testing for suitability.

FTC-L1S FINGERTIP PROPORTIONAL CONTROL LEVER

Lever deflection angle: 50° ±1°

3-pins rotary potentiometer

Neutral position switch (electromechanical type)

POTENTIOMETER & SWITCHES OPTIONS

Potentiometer Neutral position switch MC

without independent study, evaluation, and testing for suitability.

FTC-L2S FINGERTIP PROPORTIONAL CONTROL LEVER

Lever deflection angle: ±25° ±1°

3-pins rotary potentiometer

Center / bidirectional switches (electromechanical type)

POTENTIOMETER & SWITCHES OPTIONS

without independent study, evaluation, and testing for suitability.

FTC-L2S FINGERTIP PROPORTIONAL CONTROL LEVER

Lever deflection angle: ± 25° ±1°

4-pins rotary potentiometer