BC 20s Handbuch

BC-20s
Auto Hematology Analyzer
Operator’s Manual
I
I
© 2012－2015 Shenzhen Mindray Bio-medical Electronics Co., Ltd. All rights Reserved.
For this Operator’s Manual, the issued Date is 2015-02.
Intellectual Property Statement

SHENZHEN MINDRAY BIO-MEDICAL ELECTRONICS CO., LTD. (hereinafter called
Mindray) owns the intellectual property rights to this Mindray product and this manual. This
manual may refer to information protected by copyright or patents and does not convey any
license under the patent rights or copyright of Mindray, or of others.
Mindray intends to maintain the contents of this manual as confidential information.

Disclosure of the information in this manual in any manner whatsoever without the written
permission of Mindray is strictly forbidden.
Release, amendment, reproduction, distribution, rental, adaptation, translation or any other

derivative work of this manual in any manner whatsoever without the written permission of
Mindray is strictly forbidden.
, , are the trademarks, registered or otherwise, of Mindray in

China and other countries. All other trademarks that appear in this manual are used only for
informational or editorial purposes. They are the property of their respective owners.
Responsibility on the Manufacturer Party
Contents of this manual are subject to changes without prior notice.
All information contained in this manual is believed to be correct. Mindray shall not be liable
for errors contained herein nor for incidental or consequential damages in connection with the
furnishing, performance, or use of this manual.
Mindray is responsible for the effects on safety, reliability and performance of this product,
only if:
 all installation operations, expansions, changes, modifications and repairs of this product
are conducted by Mindray authorized personnel.
 the electrical installation of the relevant room complies with the applicable national and
local requirements.
 the product is used in accordance with the instructions for use.
 It is important for the hospital or organization that employs this equipment

to carry out a reasonable service/maintenance plan. Neglect of this may
I
result in machine breakdown or injury of human health.
 Be sure to operate the analyzer under the situation specified in this manual;
otherwise, the analyzer will not work normally and the analysis results will
be unreliable, which would damage the analyzer components and cause
personal injury.
NOTE
 This equipment must be operated by skilled/trained clinical professionals.
II
Warranty
THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES,

EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR ANY PARTICULAR PURPOSE.
Exemptions
Mindray's obligation or liability under this warranty does not include any transportation or
other charges or liability for direct, indirect or consequential damages or delay resulting from
the improper use or application of the product or the use of parts or accessories not approved
by Mindray or repairs by people other than Mindray authorized personnel.
This warranty shall not extend to:

 Malfunction or damage caused by improper use or man-made failure.
 Malfunction or damage caused by unstable or out-of-range power input.
 Malfunction or damage caused by force majeure such as fire and earthquake.
 Malfunction or damage caused by improper operation or repair by unqualified or
unauthorized service people.
 Malfunction of the instrument or part whose serial number is not legible enough.
 Others not caused by instrument or part itself.
III
Customer Service Department
Manufacturer: Shenzhen Mindray Bio-Medical Electronics Co., Ltd.

Address: Mindray Building, Keji 12th Road South, High-tech industrial park, Nanshan,
Shenzhen 518057,P.R.China
Website: www.mindray.com
E-mail Address: service@mindray.com
Tel: +86 755 81888998
Fax: +86 755 26582680
EC-Representative: Shanghai International Holding Corp. GmbH(Europe)
Address: Eiffestraβe 80, Hamburg 20537, Germany
Tel: 0049-40-2513175
Fax: 0049-40-255726
IV
Table of Contents
1 Using This Manual ............................................................................................... 1-1

1.1 Introduction ............................................................................................................ 1-1
1.2 Who Should Read This Manual ............................................................................. 1-2
1.3 How to Find Information ........................................................................................ 1-3
1.4 Conventions Used in This Manual ......................................................................... 1-4
1.5 Terms Used in Software Operation ....................................................................... 1-5
1.6 Symbols ................................................................................................................. 1-6
2 Understanding Your Analyzer ............................................................................ 2-1

2.1 Introduction ............................................................................................................ 2-1
2.2 Product Description ............................................................................................... 2-2
2.3 Parameter .............................................................................................................. 2-3
2.4 Main Structure ....................................................................................................... 2-4
2.5 User Interface ...................................................................................................... 2-10
2.6 Reagents, Controls and Calibrators .................................................................... 2-12
3 Understanding the System Principles............................................................... 3-1

3.1 Introduction ............................................................................................................ 3-1
3.2 Aspiration ............................................................................................................... 3-2
3.3 Dilution ................................................................................................................... 3-3
3.4 WBC/HGB Measurement ...................................................................................... 3-5
3.5 RBC/PLT Measurement ......................................................................................... 3-8
3.6 Wash .................................................................................................................... 3-11
4 Installing Your Analyzer ...................................................................................... 4-1

4.1 Introduction ............................................................................................................ 4-1
4.2 Installation Requirements ...................................................................................... 4-2
4.3 Connecting the System ......................................................................................... 4-5
4.4 Installing the Recorder Paper ................................................................................ 4-9
4.5 Precautions .......................................................................................................... 4-10
5 Operating Your Analyzer ..................................................................................... 5-1

5.1 Introduction ............................................................................................................ 5-1
5.2 Initial Checks ......................................................................................................... 5-2
5.3 Startup and Login .................................................................................................. 5-4
5.4 Daily Quality Control .............................................................................................. 5-6
5.5 Sample Preparation ............................................................................................... 5-7
5.6 Sample Analysis .................................................................................................. 5-10
5.7 Standby................................................................................................................ 5-18
5.8 Shutdown ............................................................................................................. 5-20
1
Table of Contents
6 Reviewing Sample Results ................................................................................. 6-1

6.1 Introduction ............................................................................................................ 6-1
6.2 Table Review ......................................................................................................... 6-2
7 Using the QC Programs ...................................................................................... 7-2

7.1 Introduction ............................................................................................................ 7-2
7.2 L-J QC ................................................................................................................... 7-3
7.3 X-B QC Program ................................................................................................. 7-13
8 Calibrating Your Analyzer ................................................................................... 8-1

8.1 Introduction ............................................................................................................ 8-1
8.2 When to Calibrate .................................................................................................. 8-2
8.3 How to Calibrate .................................................................................................... 8-3
9 Customizing the Analyzer Software .................................................................. 9-1

9.1 Introduction ............................................................................................................ 9-1
9.2 System Setup ........................................................................................................ 9-2
9.3 Save the settings ................................................................................................. 9-18
10 Servicing Your Analyzer .................................................................................... 10-1

10.1 Introduction .......................................................................................................... 10-1
10.2 Maintaining Your Analyzer ................................................................................... 10-3
10.3 Self-Test ............................................................................................................... 10-8
10.4 Gain Calibration ................................................................................................. 10-10
10.5 Advanced Toolbox ............................................................................................. 10-11
10.6 Sample Probe Debug ........................................................................................ 10-12
10.7 Touch Screen Calibration .................................................................................. 10-13
10.8 Viewing Logs ..................................................................................................... 10-14
10.9 Checking the Analyzer Status ........................................................................... 10-16
11 Troubleshooting Your Analyzer........................................................................ 11-1

11.1 Introduction .......................................................................................................... 11-1
11.2 Error Information and Handling ........................................................................... 11-2
12 Appendices ..........................................................................................................A-1
A Index ...................................................................................................................... A-1
B Specifications ........................................................................................................ B-1
C Communication ......................................................................................................C-1
2
1 Using This Manual
1.1 Introduction
This chapter explains how to use your Operator's Manual of BC-20s Auto Hematology
Analyzer which is shipped with your instrument and contains reference information about the
BC-20s and procedures for operating, troubleshooting and maintaining the instrument. Read
this manual carefully before operating your analyzer and operate your analyzer strictly as
instructed in this manual.
NOTE
 Be sure to operate the analyzer strictly as instructed in this manual.
1-1
Using This Manual
1.2 Who Should Read This Manual

This manual contains information written for clinical laboratory professionals to :
 learn about the BC-20s hardware and software;
 set up system parameters;
 perform daily operating tasks;
 perform system maintenance and troubleshooting.
1-2
Using This Manual
1.3 How to Find Information

This operator’s manual comprises 11 chapters and 3 appendices. Refer to the table below to
find the information you need.
If you want to … See …

learn about the intended use and parameters of Chapter 2 Understanding Your
BC-20s Analyzer
learn about the hardware and software of the BC-20s Chapter 2 Understanding Your
Analyzer
learn about how BC-20s works Chapter 3 Understanding the
System Principles
learn about the installation requirements of the BC-20s Chapter 4 Installing Your
Analyzer
learn about how to define/adjust system settings Chapter 9 Customizing the
Analyzer Software
learn about how to collect, prepare and analyze the Chapter 5 Operating Your
samples Analyzer
learn about how to use BC-20s perform your daily Chapter 5 Operating Your
operating tasks Analyzer
learn about how to review the saved analysis results Chapter 6 Reviewing Sample
Results
learn about how to use the quality control programs of Chapter 7 Using the QC
BC-20s Programs
learn about how to calibrate the BC-20s Chapter 8 Using the
Calibration Programs
learn about how to maintain/service the BC-20s Chapter 10 Maintaining Your
Analyzer
learn about how to solve the problems of the BC-20s Chapter 11 Troubleshooting
Your Analyzer
learn about the technical specifications of the BC-20s Appendix B Specifications
learn about the communication protocol of the BC-20s Appendix C Communication
1-3
Using This Manual
1.4 Conventions Used in This Manual

This manual uses certain typographical conventions to clarify meaning in the text:
Form Meaning
[××] all capital letters enclosed in [ ] indicate a key name
“××” bold letters included in " " indicate text you can find on the
screen of the BC-20s
×× italic letters indicate chapter titles, such as Chapter 1 Using This
Manual.
All illustrations in this manual are provided as examples only. They may not necessarily
reflect your BC-20s setup or data displayed.
1-4
Using This Manual
1.5 Terms Used in Software Operation

Symbols Meaning
read the statement below the symbol. The statement is
alerting you to a potentially biohazardous condition.

WARNING alerting you to an operating hazard that can cause
personnel injury.
CAUTION alerting you to a possibility of analyzer damage or unreliable
analysis results.
NOTE alerting you to information that requires your attention.
1-5
Using This Manual
1.6 Symbols
Symbols used in this manual:
When you see... It means...

alerting you to a potentially biohazardous condition.

WARNING alerting you to an operating hazard that can cause
personnel injury.
CAUTION alerting you to a possibility of analyzer damage or unreliable
analysis results.
NOTE alerting you to information that requires your attention.
You may find the following symbols on package or the body of the instrument:
When you see... It means...
CAUTION, CONSULT ACCOMPANYING

DOCUMENTS.
BIOLOGICAL RISK
HIGH VOLTAGE
EXERCISE CAUTION WHEN WORKING

AROUND TO AVIOD PRICKING
PROTECTIVE EARTH (GROUND)
ALTERNATING CURRENT
FOR IN VITRO DIAGNOSTIC USE
1-6
Using This Manual
BATCH CODE
EXPIRATION DATE
SERIAL NUMBER
DATE OF MANUFACTURE
MANUFACTURER
THE DEVICE IS FULLY CONFORMANCE

WITH THE COUNCIL DIRECTIVE
CONCERNING IN VITRO DIAGNOSTIC
MEDICAL DEVICES 98/79/EC.
THE FOLLOWING DEFINITION OF THE

WEEE LABEL APPLIES TO EU MEMBER
STATES ONLY: THE USE OF THIS SYMBOL
INDICATES THAT THIS PRODUCT SHOULD
NOT BE TREATED AS HOUSEHOLD
WASTE. BY ENSURING THAT THIS
PRODUCT IS DISPOSED OF CORRECTLY,
YOU WILL HELP PREVENT BRINGING
POTENTIAL NEGATIVE CONSEQUENCES
TO THE ENVIRONMENT AND HUMAN
HEALTH. FOR MORE DETAILED
INFORMATION WITH REGARD TO
RETURNING AND RECYCLING THIS
PRODUCT, PLEASE CONSULT THE
DISTRIBUTOR FROM WHOM YOU
PURCHASED THE PRODUCT.
AUTHORISED REPRESENTATIVE IN THE
EUROPEAN COMMUNITY
1-7
Using This Manual
(1)
Biological risk.
(2)
 Connect only to a properly earth grounded outlet.
 To avoid electrical shock, disconnect power prior to maintenance.
 To prevent fire, only use the fuse of specified type and rating.
1-8
Using This Manual
(1)
Warning: the sample probe is sharp and potentially biohazardous. Exercise caution when
working around it!
1-9
Using This Manual
1-10
Using This Manual
(1)
Warning: make sure that the protective cover is closed before operating the analyzer.
(2)
Warning
 To avoid injury, do not place your hands anywhere near the the aspiration module
when the analyzer is working.
 The sample probe is sharp and potentially biohazardous. Exercise caution when
working around it!
1-11
2 Understanding Your Analyzer
2.1 Introduction
The BC-20s is a hematology analyzer and 3-part counter for In Vitro Diagnostic Use in clinical
laboratories.
2-1
Understanding Your Analyzer
2.2 Product Description

 Intended Use
BC-20s Auto Hematology Analyzer is a quantitative, automated hematology analyzer and
3-part differential counter for in Vitro Diagnostic Use in clinical laboratories.
The purpose of this analyzer is to identify the normal patient, with all normal
system-generated parameters, and to flag or identify patient results that require additional
studies.
 Product Composition
Auto Hematology Analyzer (hereinafter called BC-20s) system consists of the main unit
(analyzer), reagents, controls and calibrators, manuals, and accessories. Performance of the
system depends on the combined integrity of all components.
2-2
2.3 Parameter
NOTE
 The purpose of this analyzer is to identify the normal patient, with all normal
system-generated parameters, and to flag or identify patient results that
require additional studies.
The analyzer is used for the quantitative determination of the following 19 parameters and
provides 3 histograms.
White Blood Cell count WBC

Lymphocyte number Lymph#
Mid-sized Cell number Mid#
Granulocyte number Gran#
Lymphocyte percentage Lymph%
Mid-sized Cell percentage Mid%
Granulocyte percentage Gran%
Red Blood Cell count RBC
Hemoglobin Concentration HGB
Mean Corpuscular Volume MCV
Mean Corpuscular Hemoglobin MCH
Mean Corpuscular Hemoglobin MCHC
Concentration
Red Blood Cell Distribution Width RDW-CV
Coefficient of Variation
Red Blood Cells Distribution Width - RDW-SD
Standard Deviation
Hematocrit HCT
Platelet count PLT
Mean Platelet Volume MPV
Platelet Distribution Width PDW
Plateletcrit PCT
White Blood Cell Histogram WBC Histogram
Red Blood Cell Histogram RBC Histogram
Platelet Histogram PLT Histogram
2-3
2.4 Main Structure

BC-20s Auto Hematology Analyzer consists of the main unit (analyzer) and accessories.
Figure 2-1 Front of the analyzer
1 ---- Touch screen 2 ---- Indicator

3 ---- Probe wipe block 4 ---- Sample probe
5 ---- [Aspirate] key
2-4
Figure 2-2 Back of the main unit
1 ---- USB port 2 --- Network interface

3 --- Power assembly 4 --- Waste sensor connector
5 --- Waste outlet 6 --- Diluent inlet
2-5
Figure 2-3 Inside of the analyzer (front cover removed)
1 --- [Aspirate] key 2 --- Start assembly

3 ---Syringe module
2-6
Figure 2-4 Right side of the analyzer (right door open)
1 --- Baths 2 --- Diluent heating assembly

3 --- Waste pump 4 --- Vacuum chamber
5 --- Reagent detection assembly 6 --- Air pump
7 --- Valves 8 --- Aspiration module
9 ---Syringe module 10 ---- Probe wipe block
2-7
Figure 2-5 Left side of the analyzer
1 --- Recorder 2 --- Left door

3 --- Lock latch of the side door
2.4.1 Touch screen

The touch screen locates on the front of the main unit, which can be used to operate the
instrument and display information.
2.4.2 [Aspirate] key

The [Aspirate] key is located behind the sample probe. You can press the key to start the
analysis, dispense diluent or perform reagent maintenance.
2.4.3 Indicator
The indicator may light in red, yellow and green to indicate current status of the system.
When the indicator stays in green, the analyzer is "Ready"; when it flickers in green, the
analyzer is running; when it stays in red, the analyzer encounters error and has stopped
running; when it flickers in red, the analyzer encounters error but is still running; and when it
stays in yellow, the analyzer is sleeping.
2.4.4 USB Ports

The analyzer has 4 USB ports to connect the printer, barcode scanner, recorder, WiFi
2-8
wireless network card, etc.. The analyzer supports software upgrade through USB.
2.4.5 Network Interface

A PC can be connected to the network interface located on the back of the analyzer for
automatic data transmission.
2.4.6 Peripherals
 Keyboard (Optional)
A Keyboard can be connected to a USB port on the analyzer. You can use it to operate your
analyzer.
 Mouse (Optional)
A mouse can be connected to a USB port on the back of the analyzer. You can use it to
operate your analyzer.
 USB Printer (Optional)
A USB printer can be connected to a USB port on the back of the analyzer. You can use it to
print out reports or other interested information displayed on the screen.
Supported printers: HP LaserJet P1606dn.
 Barcode scanner (Optional)
A barcode scanner can be connected to a USB port on the back of the analyzer. You can use
it to scan the barcode information into the analyzer.
 WiFi wireless network card (Optional)

®
Supported WiFi wireless network card: NETGEAR WNA3100M.
NOTE
 When you purchase a wireless WiFi module by yourself, make sure you
comply the relevant local laws and regulations.
2-9
2.5 User Interface

2.5.1 Screen
After the starting procedure, you will enter the "Sample Analysis" screen as shown in below
figure.
Figure 2-6 "Sample Analysis" screen
2-10
2.5.2 Menus
Tap the "Menu" button to display the system menu.
Figure 2-7 System menu
Tap one of the 10 options on the system menu to enter corresponding screen.
2-11
2.6 Reagents, Controls and Calibrators

As the analyzer, reagents, controls and calibrators are components of a system, performance
of the system depends on the combined integrity of all components. You must only use the
Mindray-specified reagents (see Appendix B Specifications) which are formulated specifically
for the fluidic system of your analyzer in order to provide optimal system performance. Do not
use the analyzer with reagents from multiple suppliers. In such use, the analyzer may not
meet the performance specified in this manual and may provide unreliable results. All
references related to reagents in this manual refer to the reagents specifically formulated for
this analyzer.
Each reagent package must be examined before use. Product integrity may be compromised
in packages that have been damaged. Inspect the package for signs of leakage or moisture.
If there is evidence of leakage or improper handling, do not use the reagent.
NOTE
 Store and use the reagents as instructed by instructions for use of the
reagents.
 When you have changed the diluent, lyse, run a background to see if the
results meet the requirement.
 Pay attention to the expiration dates and open-container stability days of all
the reagents. Be sure not to use expired reagents.
 After installing a new container of reagent, keep it still for a while before
use.
2.6.1 Reagents
 M-30D Diluent
As an isotonic reagent and with specified conductivity, M-30D diluent provides stable
environment for hematology analysis.
 M-30CFL Lyse
M-30CFL lyse is formulated to lyse red blood cells and transform the hemoglobin released
from red blood cell into hemoglobin complex. It is used for WBC count, WBC 3-part
differential and HGB determination.
 Probe Cleanser
Probe Cleanser is used for the regular cleaning of the analyzer.
2.6.2 Controls and Calibrators

The analyzer uses following controls and calibrators: B30 Hematology Analyzer Control
(Impedance Method) , BC-3D Hematology Analyzer Control (Impedance Method), S30
2-12
Hematology Analyzer Control (Impedance Method), and SC-CAL PLUS Hematology

Analyzer Calibrator (Optical Method).
B30 and BC-3D controls are suspension of simulated white cells, human erythrocytes and
simulated platelets in a medium containing stabilizers and preservatives. They are used for
the quality control of Mindray 3-DIFF BC series hematology analyzers; the QC program
monitors and evaluates the precision of the measurement parameters like WBC, RBC, HGB,
MCV/HCT and PLT.
S30 and SC-CAL PLUS calibrators are suspension of simulated white cells, human
erythrocytes and simulated platelets in a medium containing stabilizers and preservatives.
They are used to calibrate some parameters (WBC, RBC, HGB, MCV/HCT and PLT) of
Mindray hematology analyzers, so as to build the metrological traceability of analysis
results.
All references related to controls in this manual refer to the "controls" and "calibrators"
specifically formulated for this analyzer by Mindray. You must buy those controls and
calibrators from Mindray or Mindray-authorized distributors.
2-13
2-14
3 Understanding the System Principles
3.1 Introduction
The analyzer uses the electrical impedance method to determine the count and size
distribution of RBC, WBC and PLT; and uses the colorimetric method to determine HGB.
Based on the above data, the analyzer calculates other parameters.
3-1
Understanding the System Principles
3.2 Aspiration
If you are to analyze a whole blood sample, present the sample to the analyzer directly, and
the analyzer will aspirate 9 μL of the whole blood sample.
If you are to analyze a capillary blood sample under the pre-dilute mode, you should first
manually dilute the sample (20 μL capillary sample needs to be diluted by 0.7 mL of diluent to
form a 1:36 dilution), and then present the pre-diluted sample to the analyzer, which will
aspirate 198uL of the sample.
3-2
3.3 Dilution
Usually in blood samples, the cells are too close to each other to be identified or counted. For
this reason, the diluent is used to separate the cells so that they draw through the aperture
one at a time as well as to create a conductive environment for cell counting. Moreover, red
blood cells usually outnumber white blood cells by 1,000 times. For this reason, lyse need to
be added to the sample to eliminate the red blood cells before the WBC counting. Because
red blood cells usually have no nucleus, they are eliminated when the lyse breaks down their
cell walls. The analyzer provides whole blood mode and predilute mode for the analysis of
different sample types.
3.3.1 Whole Blood Mode
9ul of whole
blood sample
1.41ml of
diluent
21.6ul
1:157.65
dilution
310ul of lyse 2.2ml of diluent
1:305.5 dilution for the 1:16058.6 dilution for

WBC analysis the RBC analysis
Figure 3-1 Whole blood mode dilution flow chart

As shown on Figure 3-1, under the whole blood mode, 9 μL of whole blood sample is
aspirated and diluted by 1.41mL of diluent, forming a 1:157.65 dilution. The dilution is then
divided into 2 parts: the first 21.6 μL is aspirated and diluted by about 2.2 mL of diluent to form
a 1:16058.6 dilution. This sample is used for RBC/PLT count and histogram output. The
remaining sample will be mixed with 0.31 mL of lyse to make a 1:305.5 diluted sample for
HGB, WBC count and the output of WBC histograms.
3-3
3.3.2 Predilute mode

20ul of capillary
blood sample
700ul of diluent
1:36 dilution
198ul
1410ul of lyse
35ul
1:257.34
dilution
310ul of lyse 2.2ml of lyse
1:501.6 dilution for 1:16177.1 dilution for

WBC measurement RBC measurement
Figure 3-2 Predilute mode dilution flow chart

As shown on the figure above, under the predilute mode, you must first manually mix 20 μL of
capillary blood with 0.7 mL of diluent to make a dilution of about 1:36. Then present the
dilution to the analyzer. The analyzer will aspirate 198uL of the dilution and add in 1.41 mL of
diluent to form a 1:257.34 dilution. The dilution is then divided into 2 parts: the first 35 μL is
aspirated and diluted by about 2.2 mL of diluent to form a 1:16177.1 dilution. This sample is
used for RBC/PLT count and histogram output. The remaining sample will be mixed with 0.31
mL of lyse to make a 1:501.6 diluted sample for HGB, WBC count and the output of WBC
histograms.
3-4
3.4 WBC/HGB Measurement

3.4.1 Measurement Principle:
 WBC measurement principle
The WBCs are counted by the impedance method. The analyzer aspirates certain volume of
sample, dilutes it with certain volume of conductive solution, and delivers the dilution to the
metering unit. The metering unit has a little opening which is called "aperture". An pair of
electrodes is positioned on both sides of the aperture to create a constant-current supply. As
cells are poor conductors, when each particle in the diluted sample passes through the
aperture under the constant negative pressure, a transitory change in the direct-current
resistance between the electrodes is produced. The change in turn produces a measurable
electrical pulse which is proportional to the particle size. And when the particles passes the
aperture in succession, a series of pulses are produced between the electrodes. The number
of pulses generated indicates the number of particles passed through the aperture; and the
amplitude of each pulse is proportional to the volume of each particle.
Each pulse is amplified and compared to the internal reference voltage channel, which only
accepts the pulses of a certain amplitude. All the collected pulses are thus classified based
on the reference voltage ranges of different channels, and the number of the pluses in the
WBC channel indicates the number of the WBC particles. The cell size distribution width is
represented by the number of particles falling in each channel.
Figure 3-3 Metering diagram
3.4.2 WBC-Related Parameters

 White Blood Cell count
9
WBC# (10 /L) is the number of erythrocytes, measured directly by counting the leukocytes
3-5
passing through the aperture.

Sometimes there are nucleated red blood cells (NRBC) presenting in the sample. While the
lyse will not be able to break their nuclear membrane, these NRBCs will also be counted as
WBCs. Therefore when NRBCs are found during microscopic exam, follow below formula to
modify the WBC count:
100
WBC'＝WBC ×
100＋NRBC
In the formula, WBC′ is corrected WBC count result; WBC is the WBC count provided by the
analyzer; and NRBC indicates the number of NRBCs found when every 100 WBCs are
counted.
 3-DIFF of WBC
Lyses and diluents change the sizes of each type of WBCs in various ways and at different
time. The WBCs are thus separated into 3 parts (from the largest size to the smallest):
lymphocytes, mid-sized cells (including monocytes, eosinophils, and basophils) and
granulocytes.
The analyzer then calculate the lymphocyte percentage (Lymph%), mid-sized cell percentage
(Mid％) and granulocyte percentage (Gran%) (all presented in %) based on the WBC
histograms and in accordance with below formulae:
PL
Lymph% = × 100
PL + PM + PG
PM
Mid% = × 100
PL + PM + PG
PG
Gran% = × 100
PL + PM + PG
In the formulae: PL indicates the number of cells falling in the lymphocyte region, PM the
number of cells falling in the mid-sized cell region, and PG the number of cells falling in the
granulocyte region. All three parameters are presented in 109/L.
When the three percentages are obtained, the analyzer automatically proceeds to calculate
the lymphocyte number (Lymph#), mid-sized cell number (Mid#) and granulocyte number
9
(Gran#) with below formulae, all parameters expressed in 10 /L.
Lym% × WBC
Lymph# =
100
Mid % × WBC
Mid # =
100
Gran % × WBC
Gran # =
100
3-6
9
Lymph％, Mid％ and Gran％ are expressed in %, while WBC is in 10 /L.
 White blood cell histogram
Besides the count results, the analyzer also provides a WBC histogram which shows the
WBC size distribution, with the x-aixs representing the cell size (in fL) and the Y-axis
9
representing relative cell number (in 10 /L). After each analysis cycle, you can either check
the WBC histogram in the analysis result area on the "Sample Analysis" screen or review
the histogram on the "Review" screen.
WBC = n × 109 / L
3.4.3 HGB Measurement

The HGB is determined by the colorimetric method. The diluted sample is delivered to the
WBC count bath where it is bubble mixed with a certain amount of lyse, which breaks red
blood cells, and converts hemoglobin to a hemoglobin complex. An LED is mounted on one
side of the bath and emits a beam of monochromatic light with 530~535nm central
wavelength. The light is received by an optical sensor mounted on the opposite side, where
the light signal is first converted to current signal and then to voltage signal. The voltage
signal is then amplified and measured and compared to the blank reference reading (reading
taken when there is only diluent in the bath), and the HGB (g/L) is measured and calculated
automatically. The whole measurement and calculation process is completed automatically.
You can review the results in the analysis result area on the "Sample Analysis" screen.
HGB is expressed in g/L.
 Blank Photocurrent 
HGB(g/L) = Constant × Ln  
 Sample Photocurrent 
3-7
3.5 RBC/PLT Measurement

3.5.1 Impedance Method
RBCs/PLTs are counted by the electrical impedance method. The analyzer aspirates certain
volume of sample, dilutes it with certain volume of conductive solution, and delivers the
dilution to the metering unit. The metering unit has a little opening which is called "aperture".
An pair of electrodes is positioned on both sides of the aperture to creates a constant-current
supply. As cells are poor conductors, when each particle in the diluted sample passes
through the aperture under the constant negative pressure, a transitory change in the
direct-current resistance between the electrodes is produced. The change in turn produces a
measurable electrical pulse which is proportional to the particle size. And when the particles
passes the aperture in succession, a series of pulses are produced between the electrodes.
The number of pulses generated indicates the number of particles passed through the
aperture; and the amplitude of each pulse is proportional to the volume of each particle.
Each pulse is amplified and compared to the internal reference voltage channel, which only
accepts the pulses of a certain amplitude. All the collected pulses are thus classified based
on the reference voltage thresholds of different channels, and the number of the pluses in the
RBC/PLT channel indicates the number of the RBC/PLT particles. The cell size distribution
width is represented by the number of particles falling in each channel.
Figure 3-4 Metering diagram
3.5.2 RBC-Related Parameters

 Red Blood Cell count
12
RBC (10 /L) is the number of erythrocytes, measured directly by counting the erythrocytes
passing through the aperture.
3-8
RBC = n × 1012 / L
 Mean Corpuscular Volume
The analyzer calculates the mean cell volume (MCV, in fL) based on the RBC histogram.
 HCT, MCH and MCHC
The hematocrit (HCT, %), mean corpuscular hemoglobin (MCH, pg) and mean corpuscular
hemoglobin concentration (MCHC, g/L) are calculated as follows:
RBC × MCV
HCT =
10
HGB
MCH =
RBC
HGB
MCHC = × 100
HCT
12
where RBC is expressed in 10 /L, MCV is expressed in fL and HGB is expressed in g/L.
 RDW-CV
Red Blood Cell Distribution Width - Coefficient of Variation (RDW-CV) is derived based on
RBC histogram. It is expressed in %, and indicates the variation level of RBC size
distribution.
 RDW-SD
Red Blood Cells Distribution Width - Standard Deviation (RDW-SD, in fL) measures the width
of the 20% level (with the peak taken as 100%) on the RBC histogram, as shown in Figure
3-5..
Figure 3-5
 Red blood Cell Histogram
Besides the count results, the analyzer also provides a RBC histogram which shows the RBC
size distribution, with the x-aixs representing the cell size (in fL) and the Y-axis representing
12
relative cell number (10 /L). After each analysis cycle, you can either check the RBC
histogram in the analysis result area on the "Sample Analysis" screen or review the
histogram on the "Review" screen.
3-9
3.5.3 PLT-Related Parameters

 Platelet count
9
PLT (10 / L) is measured directly by counting the platelets passing through the aperture.
PLT = n × 10 9 / L
 Mean Platelet Volume
Based on the PLT histogram, this analyzer calculates the mean platelet volume (MPV, fL).
 PDW
Platelet distribution width (PDW) is derived from the platelet histogram, and is reported as 10
geometric standard deviation (10 GSD).
 PCT
The analyzer calculates the PCT (％) as follows:

9
where the PLT is expressed in 10 /L and the MPV in fL.
PLT × MPV
PCT =
10000
 Platelet-Large Cell Ratio
Based on the PLT histogram, this analyzer calculates the large platelet ratio (%).
 Platelet Histogram
Besides the count results, the analyzer also provides a PLT histogram which shows the PLT
size distribution, with the x-aixs representing the cell size (in fL) and the Y-axis representing
9
relative cell number (in 10 /L). After each analysis cycle, you can either check the PLT
histogram in the analysis result area on the "Sample Analysis" screen or review the
histogram on the "Review" screen.
3-10
3.6 Wash
After each analysis cycle, each element of the analyzer is washed:
 The sample probe is washed internally and externally with diluent;
 The baths are washed with diluent;
 Other elements of the fluidic system are also washed diluent.
3-11
4 Installing Your Analyzer
4.1 Introduction
CAUTION
 Installation by personnel not authorized or trained by Mindray may cause
personal injury or damage your analyzer. Do not install your analyzer
without the presence of Mindray-authorized personnel.
The analyzer is tested and packed with care before it is shipped from the factory. When you
receive your analyzer, carefully inspect the carton. If you see any signs of mishandling or
damage, contact Mindray Customer Service department or your local distributor immediately.
4-1
Installing Your Analyzer
4.2 Installation Requirements

Before installation, you should ensure that the following space, power, environmental and
fuse protection requirements are met.
4.2.1 Space Requirements

Check the site for proper space allocation. In addition to the space required for the analyzer
itself, arrange for:
 at least 30 cm to both left and right sides;
 at least 10 cm behind the analyzer;
 enough room on or below the countertop to accommodate the reagent (for example
diluent) and waste containers.
 the table (or the floor) where the analyzer is placed shall be able to withstand at least
40kg of weight.
4.2.2 Power Requirements

Voltage Input power Frequency
Analyzer (100V-240V～) ±10% 300 VA (50/60Hz)±1Hz
Fuse: 250V T3.15AH
WARNING
 Make sure the analyzer is properly grounded.
 Before turning on the analyzer, make sure the input voltage meets the
requirements.
CAUTION
 Using pinboard may bring electrical interference and the analysis results
may be unreliable. Place the analyzer near the electrical outlet to avoid
using the pinboard.
 Please use the original power cable shipped with the analyzer. Using other
electrical wire may damage the analyzer or lead to unreliable analysis
results.
4-2
4.2.3 Environment Requirements

Storage Environment Working Environment
Ambient Temperature -10℃～40℃ 10℃～40℃

Relative Humidity 10%～90% 10%～90%
Atmospheric Pressure 50kPa～106kPa 70kPa～106kPa
The environment shall be as free as possible from dust, mechanical vibrations, loud noises,
and electrical interference. Do not place the analyzer in direct sunlight or in front of a source
of heat or drafts. Please use a separate power socket; do not use the same socket with
devices like air conditioning, refrigerator and ultrasonic system, as they may interfere with the
proper operation of the analyzer. It is advisable to evaluate the electromagnetic environment
prior to operation of this analyzer. Do not place the analyzer near brush-type motors,
flickering fluorescent lights, and electrical contacts that regularly open and close. The
environment shall be well ventilated. Do not place the analyzer in direct sunlight. Connect
only to a properly earth grounded outlet. Only use this analyzer indoors.
WARNING
 Do not place the analyzer in a flammable or explosive environment.
NOTE
 If the ambient temperature is out of the specified operating range, the
analyzer will alarm you for abnormal ambient temperature and the analysis
results may be unreliable. When temperature errors are reported in the error
information area after analysis, see Chapter 11 Troubleshooting Your
Analyzer for solutions.
4-3
4.2.4 Moving and Installing the Analyzer
WARNING
 Installation by personnel not authorized or trained by Mindray may cause
personal injury or damage your analyzer. Do not install your analyzer
without the presence of Mindray-authorized personnel.
NOTE
 To protect it from being damaged during transportation, the aspiration
module is fixed by cables ties and clamps before the analyzer is shipped out
of factory. Remove the cable ties and clamps before using the analyzer.
Moving and installation of the analyzer shall be conducted by Mindray-authorized personnel.

Do not move or install your analyzer without the presence of Mindray-authorized personnel.
4-4
4.3 Connecting the System

Connect the power and the reagents as shown below. Make sure the connections are correct
and firm.
.
Figure 4-1 Connecting the analyzer to power outlet
4-5
Figure 4-2 Connecting the analyzer to power outlet
WARNING
 Be sure to dispose of reagents, waste, samples, consumables, etc.
according to government regulations.
 The reagents are irritating to eyes, skin and diaphragm. Wear proper
personal protective equipment (e.g. gloves, lab coat, etc.) and follow safe
laboratory procedures when handling them and the contacted areas in the
laboratory.
 If reagents accidentally spill on your skin or in your eyes, rinse the area with
ample amount of clean water; seek medical attention immediately.
4-6
Figure 4-3 Connecting reagents placed outside the analyzer
Figure 4-4 Connecting reagents placed inside the analyzer
4-7
CAUTION
 Make sure the diluent pipe and waste pipe are no longer than 1500mm.
 The top of the waste container and the diluent container should be lower
than the countertop where the analyzer is placed.
4-8
4.4 Installing the Recorder Paper
NOTE
 Remove the protective paper in the recorder before installing recorder
paper.
Follow the procedure below to install the record paper.
1. Use the latch at the upper right corner of the recorder door to pull the door open.
2. Insert a new roll into the compartment with the paper end out of the recorder exit, as
shown below.
3. Close the recorder door.
4. Check whether the paper is installed correctly and the paper end is feeding from the
top.
Paper roll
Figure 4-5 Installing recorder paper
CAUTION
 Use only specified thermal recorder paper. Otherwise, it may cause damage
to the recorder head, or the recorder may be unable to print, or poor print
quality may result.
 Never pull the recorder paper with force when a recording is in process.
Otherwise the recorder may be damaged.
 Do not leave the recorder door open unless you are installing paper or
removing errors.
 Improper installation of recorder paper may jam the paper and/or result in
blank printout.
4-9
4.5 Precautions
 If the analyzer is kept in an environment with heavy dust for a long time, its performance
may be reduced.
 It is recommended to clean and sterilize the outer surface the analyzer with 75%
ethanol.
 The probe wipe block of the analyzer (see Figure 2-1 Front of the analyzer) shall be
wiped with 75% alcohol regularly.
 Collect and prepare samples in accordance with the standard procedure of your
laboratory; otherwise it may result in inaccurate analysis results or damage to the
analyzer.
 If any of the pipes or fluidic components are worn out, stop using the analyzer and
contact Mindray customer service department immediately for inspection or
replacement.
 Make sure the tubings of the reagents (including diluent, lyse and waste) are not
pressed by heavy objects or bent over.
 Use only Mindray-specified reagents; otherwise it may result in inaccurate results or

damage to the analyzer.
 Pay attention to the expiration dates and open-container stability days of all the reagents.
Be sure not to use expired reagents. Otherwise it may result in inaccurate results.
4-10
5 Operating Your Analyzer
5.1 Introduction
This chapter provides step-by-step procedures for operating your analyzer on a daily basis.
A flow chart indicating the common daily operating process is presented below.
操作前的准备
Initial checks
Power on
Daily Quality
Control
Sample
Collection and
Handling
Run Sample
Shutdown
5-1
Operating Your Analyzer
5.2 Initial Checks

Perform the following checks before turning on the analyzer.
 All the samples, controls, calibrators, reagents, wastes and areas contacted
them are potentially biohazardous. Wear proper personal protective
equipment (e.g. gloves, lab coat, etc.) and follow safe laboratory procedures
when handling them and the contacted areas in the laboratory.
WARNING
 The reagents are irritating to eyes, skin and diaphragm. Wear proper
personal protective equipment (e.g. gloves, lab coat, etc.) and follow safe
laboratory procedures when handling them and the contacted areas in the
laboratory.
 If reagents accidentally spill on your skin or in your eyes, rinse the area with
ample amount of clean water; seek medical attention immediately.
 To prevent personal injury during the operation, keep your clothes, hairs
and hands from the moving parts like sample probe.
NOTE
 Use the reagents specified by the manufacturer only. Store and use the
reagents as instructed by instructions for use of the reagents.
 Check if the reagent tubings are properly connected before using the
analyzer.
 After installing a new container of reagent, keep it still for a while before
use.
 Checking the waste container
Check and make sure the waste container (not supplied) is empty.
 Checking tubing and power connections
Check and make sure the reagent, waste and pneumatic unit tubes are properly connected
and not bent.
5-2
Check and make sure the power cord of the analyzer is properly plugged into the power
outlet.
 Checking recorder (optional) and printer (optional)
Check and make sure the printer and recorder are properly installed, and have enough paper.
5-3
5.3 Startup and Login

 Power on the analyzer:
1. Place the power switch at the back of the analyzer in the "I" position. The switch will
light on.
2. Make sure that the power indicator on the analyzer lights on.
3. Enter your user ID and password in the login dialog box.
Figure 5-1 Login dialog box
4. The analyzer will sequentially do the self-test and initialize the system.
5-4
NOTE
 When "Background abnormal" is reported during the startup process,
follow the corresponding troubleshooting instruction for the error in
Chapter 11 Troubleshooting to remove the error.
 The system opens different function for the user according to the user level.
The user level depends on the user ID and the password when the user logs
in.
 To switch to another user, tap the "Logout" button first. Enter the desired
user ID and password in the displayed login dialog box, and then tap "OK"
to log in.
 If you failed to run the software continuously, please contact Mindray

Customer Service Department or your local distributor.
 After startup, please make sure the date/time of the computer is correct.
 The default user ID and password for administrator are both "Admin".
 1-12 characters are allowed for user ID and password; Chinese characters
are not allowed.
5-5
5.4 Daily Quality Control

Before running any samples, run the controls to finish auto setup and ensure reliable results
of the analyzer. See Chapter 7 QC programs for details.
5-6
5.5 Sample Preparation

The analyzer supports two sample types: whole blood sample (including capillary whole
blood sample) and predilute sample.
CAUTION
 Prepare samples following the recommend procedure of the manufacturer.
 Always shake the samples as shown below to well mix it
WARNING
 Do not contact the patients' sample blood directly.
CAUTION
 Do not reuse disposable products such as collection tubes, test tubes,
capillary tubes and so on.
NOTE
 Be sure to use clean EDTAK2 anticoagulant collection tubes, fused silica
5-7
glass/plastic test tubes, centrifugal tubes and borosilicate glass capillary

tubes.
 Be sure to use the Mindray-specified disposable products including

evacuated blood collection tube, anticoagulant collection tubes and
capillary tubes etc.
5.5.1 Whole Blood Samples (Including Capillary Whole Blood
Samples)
1. Use clean EDTAK2 anticoagulant collection tubes to collect venous blood samples.
2. Mix the sample immediately according to your laboratory’s protocol.
CAUTION
 To attain accurate analysis results, make sure the sample volume is no less than
120uL.
NOTE
 For the whole blood samples to be used for WBC differential, you shall store
them at the room temperature and run them within 8 hours after collection.
 Samples stored in a refrigerator at the temperature of 2℃～8℃ must be

analyzed within 24 hours after collection. The refrigerated samples must be
kept at room temperature for at least 30 minutes before analysis.
 Be sure to mix any sample that has been prepared for a while before running
it.
 After the sample is prepared, be sure to wait for at least 5 minutes before
running it; and you must complete the analysis within 2 hours after its
collection.
5.5.2 Prediluted Sample

1. Tap the mode switching icon to switch the working mode from whole blood to "PD".
5-8
2. Tap the "Diluent" button on the top status bar, a message box will pop up.
Figure 5-2 "Diluent" dialog box
3. Present a tube to the analyzer, and tap the [Aspirate] key on the analyzer to dispense
diluent (700μL). During dispensing the diluent, a progress bar will display.
4. If more portions of diluent are needed, repeat the procedure.
5. Add 20μL of capillary blood to the centrifugal tube of diluent, close the tube cap and
shake the tube to mix the sample.
6. After the prediluted sample is prepared, tap the “Cancel” button to exit dispensing the
diluent.
NOTE
 You can also dispense 700μL of diluent by pipette into the tube.
 Take methods to prevent the diluent from dust and volatilization; otherwise
the results may be unreliable.
 After mixing the capillary sample with the diluent, be sure to wait at least for
3 minutes, and mix the sample again before running the sample.
 Be sure to run the prediluted samples within 30 minutes after the dilution.
 Be sure to mix any sample that has been prepared for a while before running
it. Do not use a vortex mixer for mixing, for the shaking be too violent and
cause hemolysis.
 Be sure to evaluate predilute stability based on your laboratory’s sample

population and sample collection techniques or methods.
5-9
5.6 Sample Analysis

Tap "Sample Analysis" to enter the sample analysis screen. Tap the "Mode" switching
button on the sample analysis screen to select from "WB" and "PD" modes.
5.6.1 Enter Sample Information

You can either enter the ID or the full information of samples.
You can skip the sample information entering procedure at this stage, but enter the
information based on sample ID or sample result saving time after analysis. For details,
check Chapter 6 Reviewing Sample Results.
Before entering sample information on the "Sample Analysis" screen, set up your desired
way for entering sample information on the "Setup→Auxiliary Setup" screen (see Chapter 9
Customizing the Analyzer Software).
Enter all information

When you have set "Entry of next sample info" to "Enter all information", tap "Next
sample" on the "Sample Analysis" screen, and a dialog box pops up as below. You can
enter full sample information for the next sample except for "Ref. group", for the system will
assign a matched group automatically.
Figure 5-3 Enter all information
 Entering the sample ID
Enter the ID in the "Sample ID" box.
5-10
NOTE
 You can enter letters, digits and all other characters on the keyboard for
sample ID, only for [a-z][A-Z][0-9][-_].
 1 to 20 characters are allowed. It cannot be left empty.
 The sample ID must end with a digit; and it cannot only consist of "0".
 Entering the patient ID
Enter the patient ID to the "Patient ID" box.
 Entering the patient name
Enter the patient name in the "Patient" box.
 Entering the patient gender
Select the desired item (“Male”, “Female”, or null) from the "Gender" pull-down list. The
default option is "Unknown".
 Entering the date of birth
Enter the birth date of the patient into the "Date of Birth" box, the birth date format being the
same of the system date.
 Entering the patient age
The analyzer provides 5 ways for you to enter patient age – in years, in months, in days and
in hours. The first way is designed for the patients no younger than one year; the second for
the infant patients of one month to two year; the third for the neonatal of one week to ten
weeks; the fourth for the neonatal no older than one month, and the fifth for the neonatal no
older than 48 hours. You may choose one of the four ways to enter the patient age.
Select the desired item from the "Age"pull-down list (“Years”, "Month(s)”, “Weeks”,”Days”
and “Hours”), and you may enter the patient age in the box followed by the age unit.
NOTE
 When you enter the patient birth date, the system will automatically
calculate the patient age using the entered "Birth of Date" and current
"System Date" and display the result in the "Age" box and the age "Unit"
combo box, The "Age" box will then be greyed, and will become editable
again when the "Date of Birth" is cleared.
 The patient birth date should be no later than current system date.
5-11
 Entering the patient type
Select "Outpatient", "Inpatient", "Medical Examination" or "STAT" from the "Patient Type"
pull-down list.
 Entering the department name
You can either enter the department name in the "Department" box, or select the desired
department from the "Department" pull-down list (if there are previous entries saved in the
list)..
 Entering the bed number
Enter the bed number of the patient to the "Bed No." box.
 Entering the draw time
Enter the time when the sample is collected into the "Draw Time" box.
 Entering the delivery time
Enter the time when the sample is sent into the "Delivery Time" box.
 Entering the clinician name
You can either enter the clinician name into the "Clinician" box, or select the desired clinician
from its pull-down list (if there are previous saved entries in the list).
 Entering the comments
Enter necessary information to the "Comments" box.
 OK
When you have finished entering the sample information, tap "OK" to save the information
and return to the "Sample Analysis" screen.
 Cancel
If you do not want to save the entered sample information, tap "Cancle" to return the
"Sample Analysis" screen without saving the changes.
Enter sample ID
When you have set "Entry of next sample info" to "Enter sample ID only", tap "Next
sample" on the "Sample Analysis" screen, and a dialog box pop up as below.
5-12
Figure 5-4 Enter sample ID
Enter the ID in the "Sample ID" box. Tap the "OK" button to save the sample ID and close the
dialog box. The ID will be displayed in the "Next Sample" information area on the bottom of
the screen.
Edit current sample information

Tap the sample information area of the sample analysis screen or graph review screen, the
“Edit Info” dialog box will pop up. In this dialog box, you can edit the information of the
sample whose analysis is just completed. This function does not apply to background
analysis and validated samples.
5-13
5.6.2 Running the Samples
WARNING
 The sample probe tip is sharp and may contain biohazardous materials.
Exercise caution to avoid contact with the sharp sample probe when
working around it.
CAUTION
 Do not reuse disposable products such as collection tubes, test tubes,
capillary tubes and so on.
NOTE
 Make sure that the sample probe is fully immersed into the sample and not
in contact with the tube bottom; otherwise the aspiration volume may be
insufficient, or the aspirated volume may not be accurate.
 Make sure the sample probe tip does not touch the tube wall, otherwise the
blood sample may spill.
Sample Analysis
Do as follows to run samples:
1. Make sure the analyzer indicator shows that the analyzer is ready for sample analysis,
and the analysis mode is "WB" or "PD".
2. Present a well mixed sample to the sample probe for aspiration.
3. Press the [Aspirate] key to start sample analysis. When the analyzer indicator flickers in
green, the analyzer is running.
4. The sample probe will automatically aspirate certain volume of the WB or PD samples.
When you hear the beeps, remove the sample tube. The probe will ascend and add the
aspirated sample to the count baths. The analyzer will automatically run the sample.
5. When the analysis is finished, the result will be displayed in the analysis result area on
5-14
the screen. The sample probe returns to the original position and gets ready for the next
analysis.
6. When "Auto print after sample analysis" is set to "On", the analyzer will automatically
print the analysis result report in the preset format; when "Auto Communicate" is set to
"On", the analyzer will automatically upload the eligible sample results as well as sample
and patient information to the LIS system.
7. Repeat above steps to run other samples.
NOTE
 If the analyzer detects clogging or bubbles during the analysis, the
corresponding error message will be displayed in the error message area
and the results of all related parameters will be invalidated. See Chapter 11
Troubleshooting Your Analyzer for solutions.
 If the ambient temperature is out of the specified operating range, the

analyzer will alarm you for abnormal ambient temperature and the analysis
results may be unreliable. When temperature errors are reported in the error
information area after analysis, see Chapter 11 Troubleshooting Your
Analyzer for solutions.
5.6.3 Processing Analysis Results

Saving of analysis results
The analyzer automatically saves sample results. When the maximum number has been
reached, the newest result will overwrite the oldest.
Histogram flags
The system will flag abnormal histograms. Both WBC histogram and PLT histogram are
flagged for abnormal results.
 WBC histogram flags
Abnormal WBC histograms will be flagged by one of the markings: R1, R2, R3, R4 and Rm.
The indications of the markings are as follows:
R1 indicates abnormality on the left side of the lymphocyte hump and possible presence of
platelet clump, giant platelet, nucleated red cell, lyse resistant RBC, high molecular weight
protein and lipoid debris in sample, or electrical noise.
R2: indicates abnormality between the lymphocyte hump and the mid-sized cell area,
possible presence of atypical/immature lymphocyte, plasma cell, blast cell in the sample,
eosinophilia or basophilia.
R3: indicates abnormality between the mid-sized cell area and the granulocyte hump,
possible presence of immature granulocyte, blast cell, left shift, immature monocyte or
eosinophilia.
R4: indicates abnormality on the right side of the granulocytes hump, possible presence of
5-15
immature granulocyte, blast cell, agglutinated white cell, or netrophilia.

Rm: indicates at least two R flags.
Editing the histogram (for administrators only)

Tap the WBC histogram to activate the editing function, and then you can edit the position of
the discriminator A or B. After the histogram is edited, the system will automatically
re-calculate the differential results.
 PLT histogram flags
Abnormal PLT histograms will be flagged by the marking Pm, PS, PL.
The indication of the marking is as follows:
Pm: indicates blur demarcation between the platelet area and red blood cell area and
possible presence of large platelet, platelet clump, small red blood cell, cell debris or high
molecular weight protein.
PS：small platelet possibly high notice.
PL：giant platelet possibly high notice.
Parameter flags
Table 1 Flags of abnormal blood cell differential or morphology

Flag type Information Meaning
WBC Flag Leucopenia Low WBC count
5-16
Leucocytosis High WBC count

Granulocyte
Low granulocyte number
decreased
Granulocyte increased High granulocyte number
NRBCs, abnormal/atypical lymphocytes,
WBC abnormal
immature or blast cells may present
Lymphocyte
Low lymphocyte number
decreased
Lymphocyte increased High lymphocyte number
Mid-size cell increased High mid-sized cell number
Pancytopenia Low WBC, RBC and PLT count
Possible presence of microcytosis,
RBC Distribution
macrocytosis, anisocytosis, RBC agglutination
Abnormal
and diamorphologic histogram.
HGB results may be abnormal or interference
HGB Abn./Interfere?
RBC Flag may exist (for example, high WBC count)
Microcytosis Small MCV
Macrocytosis Large MCV
Anemia Anemia
Erythrocytosis High RBC count
PLT Distribution Possible presence of microcytosis, RBC debris,
Abnormal large platelet and platelet coagulation.
PLT Flag
Thrombopenia Low PLT count
Thrombocytosis High PLT count
NOTE
 Abnormal parameter or histogram results of background check will not be
flagged. When the background results do not meet requirements, the
analyzer will alarm for abnormal background.
5-17
5.7 Standby
When the fluidics system stop working for 15 minutes (default, which can be set at the setup
screen. See Chapter 9 Customizing the Analyzer Software for details), then the analyzer will
enter the standby status automatically.
After entering the sleep mode, the bottom right of the screen displays "Standby. Press the
[Aspirate] key to exit. "
NOTE
 On the “Status” screen, the analyzer cannot enter the standby status.
 If it is the time for standby but the analyzer has an error, then only after the
error is removed will the auto-standby starts accordingly.
 You can perform the operations not involving the analyzer when it is on
standby, such as communication and print etc.
 Refer to Section 9.2.5 Maintenance Setup for how to edit waiting time before
entering standby mode.
 Under stand-by mode, if there are unfinished printing or communication

tasks, the analyzer will go on processing them.
 [Aspirate] key
Press the [Aspirate] key on the analyzer to exit the standby mode.
5-18
After canceling the standby mode, the progress bar will be closed automatically, the analyzer
will exit the standby mode.
NOTE
 Different maintenances will be performed by the analyzer automatically
when exiting the standby status, and the exiting time depends on how long
the analyzer was in the standby status.
 If any error happens during the process of exiting the standby status, see
Chapter 11 Troubleshooting Your Analyzer for details to remove the error.
 After exiting standby mode, the analyzer will return to the status before
standby. The analysis status icon on at the screen displays in green. The
indicator on the analyzer displays in green at the same time.
5-19
5.8 Shutdown
Perform the "Shutdown" procedure to shut down the analyzer every day.
WARNING
 The sample probe tip is sharp and may contain biohazardous materials.
Exercise caution to avoid contact with the sharp sample probe when
working around it.
NOTE
 To ensure stable analyzer performance and accurate analysis results, be
sure to perform the "Shutdown" procedure to shut down the analyzer after it
has been running continuously for 24 hours.
 Be sure to shut down the analyzer strictly as instructed below.
 Do not force power off the analyzer during the "Shutdown" procedure.
 If error that will affect shutdown occurs during the showdown process, the
analyzer will resume to its original status and report the error. See Chapter
11 Troubleshooting Your Analyzer for solutions.
1. Tap the "Shutdown" button on the main menu, the shutdown dialog box shown as below
will display:
Figure 5-5 Shutdown
5-20
2. Tap "OK", and follow the instruction to present probe cleanser to the sample probe, then
press the [Aspirate] key. The sample probe automatically aspirates the probe cleanser;
then the probe cleanser maintenance starts. A progress bar will be displayed on the
screen to indicate the probe cleanser maintenance progress.
3. When the shutdown procedure is finished, the screen will display "Please power off the
analyzer". Turn off the analyzer.
4. Empty the waste container and dispose of the waste properly.
WARNING
5-21
5-22
6 Reviewing Sample Results
6.1 Introduction
After every analysis cycle, the analyzer automatically saves the analysis results into the
sample database. Totally 500,000 records (including parameter results and histograms) can
be saved.
You can either choose the "Table Review" mode to review the parameter results of all
samples saved in the sample and search databases; or the "Graph Review" mode to review
both the parameter results and the histograms of each sample.
NOTE
 The sample result data must have proper backup in case of data lost caused
by hardware or software error.
6-1
Reviewing Sample Results
6.2 Table Review

You can browse, review, search, edit and export previous saved data on the "Table Review"
screen. Tap "Table Review" to enter the "Table Review" screen.
Table area
The table area displays the list of the analyzed samples with basic information like sample ID
and sample state.
6-2
NOTE
 The latest sample record is on the utmost top of the table.
Graph review
You can either tap the "Graph Review" button on the "Table Review" screen or tap
"Previous" on the "Sample Analysis" screen to review the detailed results of each sample.
6-3
Tap the button to switch between the “Count” screen and the “Graph Review” screen.
Edit results
Tap the desired sample result and it will be highlighted. Tap the "Edit Result" button and the
following dialog box will display.
Modify the results and tap "OK" to save the changes. The information on the graph review
screen will be refreshed.
Searching for sample

1. Tap "Search", the following dialog box will display.
6-4
2. Enter searching conditions into the edit boxes or select them from the pull-down
lists.
3. Tap "OK" to start search, the results will displayed in the table.
Edit information
Tap the desired sample result on the "Table Review" screen and it will be highlighted. Tap the
"Edit Info" button and the following dialog box will display.
Modify the sample and patient information as necessary, and tap "OK" to save the changes.
The information on the table review screen will be refreshed.
Validate/Cancel Validate (for administrators only)

 Validate sample data
6-5
Select the sample record(s) to be validated on the “Table Review” screen, and then tap the
"Validate" button to validate. The "Sample State" of the record(s) will become "Validated".
 Cancel validate
Select the validated sample record(s) on the "Table Review" screen, and then tap the
"Cancel validate" button. The text of "Validated" will disappear from the "Sample State".
6-6
Export
1 Tap "Export", the following dialog box will display.
2 Select "Selected" or "All" in the "Export Range" area.

Communication
 Transmit selected data
1. Select sample(s) to be transmitted on the "Table Review" screen.

2. Tap "Comm.", the following dialog box will display.
3. Tap the "Selected" radio button.

4. Tap "OK" to start transmitting specified results to the data management software.
 Transmit all data
1. Tap "Comm.", the following dialog box will display.

2. Tap the "All" radio button.
3. Tap "OK" to start transmitting all results to the data management software.
6-7
Delete (for administrators only)

1. Select the sample record to be deleted.
2. Tap the "Delete" button, the following dialog box will display.
3. Tap "OK" to delete the record, and the dialog box will be closed.
Trend Graph
Tap the "Trend Graph" button to see the trend graph of sample results.
6-8
Print
 Print reports as per the default report template
Select sample records to be printed, and then tap "Print" to print them. On the "Graph
Review" screen, the "Sample State" of the printed sample will become "Printed".
NOTE
 When a sample has been validated and printed, its "Sample State" will
display "Validated".
6-9
6-1
Using the QC Programs
7 Using the QC Programs

7.1 Introduction
Quality Control (QC) consists of strategies and procedures that measure the precision and
stability of the analyzer. The results reflect the reliability of the sample results. QC involves
measuring materials with known, stable characteristics at frequent intervals.
Analysis of the results with statistical methods allows the inference that sample results are
reliable. Mindray recommends you run the QC program daily with low, normal and high level
controls. A new lot of controls should be analyzed in parallel with the current lot prior to their
expiration dates. This may be accomplished by running the new lot of controls twice a day for
five days using any empty QC file. The QC files calculate the mean, standard deviation and
coefficient of variation for each selected parameter. The instrument-calculated means of
these ten runs should be within the expected ranges published by the manufacturer.
This analyzer provides 2 QC programs: L-J QC and X-B QC.
NOTE
 Use the controls and reagents specified by the manufacturer only. Store and
use the controls and reagents as instructed by their instructions for use.
7-2
7.2 L-J QC
7.2.1 Editing L-J Settings (for administrators only)
Before running a new lot of controls, you must set up a QC file for each lot of controls.
1 Tap the menu option "QC" > "L-J QC" > "Setup".
2 Enter the L-J QC setup screen.
.
You may set up QC information by any of the following two ways.

 Reading the information provided by the manufacturer
 Manual Entry
Reading the information provided by the manufacturer

1. Enter the L-J QC setup screen.
2. Tap "New", or select a QC file without QC results, and then tap "Edit".
3. Tap "Import File".
7-3
4. Select the QC file to be imported.

5. Tap "OK" to close the dialog box and return to the L-J QC setup screen.
6. Tap "OK" to read the selected QC information to the current QC file.
NOTE
 The "Import target/limits" check box is selected by default. If it is
deselected, the operator must enter the target and limits of QC
parameters manually.
8. Select the "Control type" from the pull-down list.

9. Select the QC mode.
10 Set QC sample ID: if you are used to analyzing control together with blood samples,
. you can set a unique ID for the control. The analyzer will recognize the sample as
control when it reads the unique ID. After the analysis completes, the results will be
saved into the QC file of the QC sample ID.
11 Tap other icons to switch screen and save the QC information.
Manual Entry
1. Enter the L-J QC setup screen.
2. Tap "New", or select a QC file without QC results, and then tap "Edit".
3. Enter the lot No. of the controls in the edit box manually.
7-4
NOTE
 The lot No. shall not be empty and up to 16 digits can be entered.
You can enter characters, numbers, letters.
4. Select the control level.

5. Enter the expiration date of the lot.
6. Select the "Control type" from the pull-down list.
7. Select the QC mode.
8. Set QC sample ID: if you are used to analyzing control together with blood samples,
you can set a unique ID for the control. The analyzer will recognize the sample as
control when it reads the unique ID. After the analysis completes, the results will be
saved into the QC file of the QC sample ID.
9. Enter the target and limits in the edit boxes according to the package insert of the lot of
controls.
10 Tap other icons to switch screen and save the QC information.
7-5
Setting limits
You can adjust the format of limits as per the following procedure:
1. Tap "Set Limits".
2. Tap “By SD” to display the limits in the form of absolute value;
or tap “By CV” to display the limits in the form of percentage.
3. Tap the “OK” button to save the settings.
7.2.2 Running Controls

You can select one of the two ways below to run controls:
 Run controls under the "QC" screen.
 Put controls together with normal samples, and run the controls under the sample
analysis screen.
Run controls under the "QC" screen

After editing the QC information, you can start QC analysis by one of the following ways
according to the selected QC mode.
 Whole blood
 Predilute
CAUTION
 Running QC sample with error present will lead to unreliable results. If
errors are reported during QC analysis, remove the errors first and then
continue with the analysis.
 Sample agglutination may result in inaccurate analysis results. Check the

control samples to see if there is any agglutination, if yes, process the
samples according to your laboratory's protocols.
7-6
NOTE
 When switching mode from "PD" to "WB", a progress bar will be displayed
while the analyzer runs mode switching sequence.
1 Tap "QC" > "L-J QC" > "Count" to enter the QC count screen.
NOTE
 Be sure that the level of the control to be run is the same with the
current QC file, and the control is not expired.
 The expiration date of expired controls is displayed in red.
2 Prepare the control as instructed by instructions for use of the controls.

3 Run QC analysis:
. 1) Make sure the analysis mode is "WB" or "PD" and the indicator of the analyzer is
green.
2) Shake the vial of sample as instructed by instructions for use of the control to mix the
sample thoroughly.
3) Present the control sample to the sample probe. Press the [Aspirate] key to start QC
run.
4) When you hear the beep, remove the control.
4 When analysis finishes, the QC results will be displayed in the current screen and be
. saved in the QC file automatically.
7-7
NOTE
 Up to 100 QC results can be saved in each QC file.
5 Do the above procedures to continue running QC analysis if necessary.
Put controls together with normal samples, and run the controls under the sample analysis
screen.
After setting special "QC Sample ID" for a control under the QC setup screen, you can put
the control together with normal samples, and run it under the “Sample Analysis” screen.
When editing worklist or entering next sample information in the "Next Sample" dialog box
before daily analysis, enter the special "QC Sample ID" as "Sample ID".
Based on the QC mode selected, you can choose to run QC analysis from one of the
following ways:
 Whole blood
 Predilute
1. Prepare the control as instructed by instructions for use of the controls.

2. Refer to section 5.5 Sample Preparation for sample preparation under whole blood
and predilute modes.
3. When it is ready to run a sample (i.e. the status icon and the analyzer indicator is
green), present the sample to the sample probe.
4. When you hear the beep, remove the control.
5. When analysis finishes, the QC results will be displayed in the current screen and be
saved in the QC file automatically.
NOTE
 Up to 100 QC results can be saved in each QC file.
6. Do the above procedures to continue running QC analysis if necessary.
NOTE
 When switching blood mode from "PD" to "WB", a progress bar will be
displayed while the analyzer runs mode switching sequence.
Editing and saving results (for administrators only)
Tap "Edit Result" on the QC screen to edit results and tap "OK" to save the edited results.
The edited results will be marked with an "E".
7-8
Restore results (for administrators only)
Operators of administrator access level can restore the edited results to the original
measurement results.
1. Tap "Restore" on the "Edit Result" screen.
2. Tap "OK" to restore the measurement values.

3. Tap "OK" to close the dialog box and start to restore results.
7.2.3 Reviewing L-J Results

After QC analysis, you can review the QC results in the following ways:
 QC Graph
 QC Table
X-B QC graph review

1. Tap "Graph" button on the "L-J QC Run" screen to enter the L-J QC graph screen.
2. You can tap the arrow buttons on the right of the graph to browse graphs of the
parameters. You can tap the arrow buttons under the graph horizontally to browse all
the QC results.
7-9
NOTE
 If a parameter target/limits of the QC files with QC results are modified and
saved, and the targets/limits of other parameters changes accordingly,
those changed data will be highlighted in yellow.
Print
Tap the "Print" icon in the status bar to print information of the current QC file and the QC
graph of all parameters.
NOTE
 The green vertical line and values of the corresponding QC points will not
be printed.
L-J QC table review

1. Tap the "QC Table" button on the "L-J QC Run" screen to enter the L-J QC table
screen.
2. You can tap the arrow buttons on the right of the QC table to browse all QC
records. You can tap the arrow buttons under the QC table to browse all the
parameter results.
7-10
NOTE
 If a parameter target/limits of the QC files with QC results are modified and
saved, and the targets/limits of other parameters changes accordingly,
those changed data will be highlighted in yellow.
Delete (for administrators only)
1. Tap "Delete", the following dialog box will display.
2. Tap "Yes" to delete the selected records.
NOTE
 The operation will be recorded in the system log.
Print
You can tap the "Print" icon in the status bar to print the QC table.
Transmission
To transmit QC data to external data management software or HIS/LIS/HIS, tap the "Comm."
button to transmit specified results to the data management software.
NOTE
 If auto-communication is enabled and a sample is run during the
transmission of the QC data, then only when the QC data transmission
finished will the auto-communication of the sample result start.
 The QC data saved in the process of transmission will not be transmitted.
7-11
Export
To Export QC information and results of the current QC file, do as follows:

1. Insert a USB and then tap "Export".
2 The system will detect the USB and export data automatically.
3 The prompt "Export succeeded!" will display.
7-12
7.3 X-B QC Program

7.3.1 Introduction
The X-B analysis is a weighted moving average analysis that uses values obtained from
patient samples. It uses the 3 red cell indices, MCV, MCH and MCHC to indicate the
hematology instrument performance.
It is recommended the X-B QC be activated when the sample volume of your laboratory is
greater than 100 samples per day. Effective use of X-B requires randomization of samples
and a normal cross section of patients to prevent skewing of indices. It observes the trend of
QC results in the reference range formed by the specified target and limits.
The analyzer implement X-B QC on the 3 parameters: MCV, MCH and MCHC, each group of
samples for X-B analysis consists of 20-200 sample results obtained from normal analysis of
both WB and PD modes. The analyzer can save up to 1,000 X-B QC results. When the saved
QC results have reached the maximum number, the newest result will overwrite the oldest.
7.3.2 Editing X-B Settings (for administrators only)

Tap the menu option "QC">"X-B QC">"Setup", the following screen will display.
On the X-B QC setup screen, you may activate/deactivate X-B QC, set target/limits, and
configure the sample validity setup.
7-13
Editing X-B settings

1. In the “Sample number/group.” edit box, you may enter the amount of samples
[within the range 20(default) to 200] to be included in calculating for an X-B QC
point.
2. Set X-B QC "On" or "Off". If X-B QC is activated, the samples meeting validity
requirements will be included in X-B QC.
Set target/limits
Before the X-B QC analysis, you shall set up the target and limit for each parameter at the
X-B QC setup screen.
NOTE
 The units of target/limits of all parameters are the same as those in the
parameter unit setup screen.
In the “Target/Limit” area of the X-B QC setup screen, specify the targets and limits in
1.
the “Target/Limit” table by entering manually.
NOTE
 Do not leave any of the targets and limits for the QC parameters
blank.
 When first use, the default setting will provide the initial values for
the targets and limits of all QC parameters.
2. Tap other icons to switch screen and save the settings.
Setting sample validity

In X-B QC, sample results conforming to any of the following conditions will be considered as
invalid and cannot be used in the QC calculation.
 Sample results exceeding the linearity range;
 Background results;
 Sample results not conforming to the "Sample Validity Setup";
 QC data for QC programs other than X-B;
 Calibration data;
 Results generated while there are errors which could affect the accuracy of the
results (insufficient aspiration volume or clogging for example).
"Sample Validity Setup" is to set up the ranges of valid RBC, MCV, MCH and MCHC results.
Only when the results of all these four parameters are within the specified ranges, the sample
results can be used for X-B QC calculation. Do as follows to set the sample validity:
7-14
Select "On" to activate X-B QC.

1
In the "Sample Validity Setup" of the X-B QC setup screen, set the upper and lower
. limits of the 4 parameters in the sample validity setup area.
The default validity range of each parameter is shown in the following figure.
2 Tap "Save" to save the setup.
7-15
NOTE
 In the sample validity setup, the upper limit shall be no smaller than the
lower limit. Otherwise, there will be prompted message asking you to revise.
 The valid ranges of the RBC parameters are their linearity ranges; the valid
ranges of other parameters are their display ranges.
 All the entries shall be numbers with only one decimal point. The length of
the number entered cannot be longer than the length of the text box.
 Once the validity range is changed, the previous results will not be used in
the QC calculation as valid results. For example, if 20 valid samples are
needed for the X-B QC calculation, when you change the validity range after
10 groups of valid sample results have been acquired, these 10 groups of
results will be discarded, and only valid sample results generated
afterwards will be used in the QC calculation.
 The units of lower and upper limits of all parameters are the same as those
in the " Reference Unit Setup " screen. See section 9.2.4 Setting Parameters-
Parameter unit setup.
Setting limits
You can adjust the format of limits as per the following procedure:
1. Tap "Set Limits".
2. Tap “By SD” to display the limits in the form of absolute value;
3. Tap “By CV” to display the limits in the form of percentage.
4. Tap the “OK” button to save the settings.
7-16
Restore defaults
If you want to restore the default targets and limits of the parameter, tap "Restore Defaults".
The default values of the target and limits of each parameter are as follows:
Parameter Target Limits (#)
MCV 89.5 2.7
MCH 30.5 0.9
MCHC 340 10
7.3.3 QC Analysis
After editing X-B setup, the system will start X-B QC automatically.
After every 20~200 results (determined by the setting) are obtained, the system will perform
the X-B calculation once automatically. You can review the result in X-B QC graph or X-B QC
table.
7.3.4 Reviewing X-B Results

After QC analysis, you can review the QC results in the following ways:
 QC Graph
 QC Table
X-B QC graph review
1. Tap the menu option "QC" > "X-B QC" > "Graph", the following screen will display.
7-17
2. Select QC file No., the information of the file and the QC graph will be displayed on the
screen.
3. You can tap the arrow buttons under the graph horizontally to browse all the QC
results.
X-B QC table review
1. Enter the "X-B QC Graph" screen.

2. Tap the "Table" button to enter the X-B QC table screen.
3. You can tap the arrow buttons on the right of the QC table to browse all QC records.
The delete, print and export operations can all be performed same as stated in the L-J QC
table review section.
7-18
8 Calibrating Your Analyzer
8.1 Introduction
Calibration is a procedure to standardize the analyzer by determining its deviation under
certain specified conditions. In order to get accurate sample analysis results, you should
calibrate the analyzer per the procedure below when necessary.
The analyzer supports 3 calibration programs, namely manual calibration, auto calibration
using calibrators and auto calibration using fresh blood samples; and two calibration modes,
namely "WB" and "PD".
All the parameters or part of the parameters of WBC, RBC, HGB, MCV and PLT can be
calibrated by the calibration programs.
NOTE
 Calibration procedures can only be performed by users of the
administrator-level.
 Use the calibrators and reagents specified by the manufacturer only. Store
and use the calibrators and reagents as instructed by their instructions for
use.
 Calculation of reproducibility is included in the calibration procedure.
8-1
Calibrating Your Analyzer
8.2 When to Calibrate

This analyzer is calibrated at the factory just before shipment. It is electronically stable and
does not require frequent recalibration if you operate and maintain it as instructed by this
manual. You only need to recalibrate this analyzer if:
 an analytical component has been changed.
 you are going to re-use the analyzer after a long-term storage.
 the quality control results indicate there may be a problem.
NOTE
 All of the measured parameters must be calibrated before readings of this
analyzer can be used as valid analysis results.
8-2
8.3 How to Calibrate

8.3.1 Preparing Your Analyzer
Do the following pre-calibration procedures before calibration. If problems are detected
during these checks, do not attempt to calibrate the analyzer. If necessary, call Mindray
Customer Service Department or your local distributor for assistance.
1. Check and make sure enough reagents have been prepared for the calibration. You need
to start over the calibration if the reagents run out during the process.
2. Check the background (for calibration right after startup) or blank count results .If the
analyzer alarms for abnormal background results, see Chapter 11 Troubleshooting Your
Analyzer for solutions (see Appendix B Specifications for the background range).
3. Run a vial of normal control consecutively for 10 times under the whole blood mode.
Enter the "Table Review" screen to check the reproducibility of the 10 runs and make
sure they meet the following requirements.
Parameter Range Whole Blood Predilute

Reproducibility (CV) Reproducibility
(CV)
≤ 3.5% ≤ 4.0%
9 9
WBC 4.0×10 /L～6.9× 10 / L
≤ 2.0 ≤ 4.0%
9 9
7.0×10 /L～15.0× 10 / L
RBC 3.50 × 10 / L ~ 6.50 × 10 / L
12 12
≤ 1.5% ≤2.0%
HGB 100 g/L ~ 180 g/L ≤ 1.5% ≤2.0%
MCV 70 fL～110 fL ≤ 1.0% ≤1.5%
PLT 100 × 10 / L ~ 149 × 10 / L
9 9
≤ 5.0% ≤8.0%
150 × 10 / L ~ 500 × 10 / L
9 9
≤4.0% ≤8.0%
It is recommended that you create a log table for your analyzer. This log table should contain
all necessary information that is pertinent to your analyzer. Suggested items that you may
want to include in the log table are: calibration date, supplier of calibrator, lot number,
expected results and limits, and result of background check.
NOTE
 Be sure to use the evacuated collection tubes recommended in the
Appendix.
 If fresh blood samples are used for reproducibility test, make sure the
sample volume is enough to support the test.
8-3
8.3.2 Manual Calibration

Tap "Calibration" > "Manual" in the menu to enter the following screen.
NOTE
 If you log in at the operator access level, you can only view the calibration
factors. To perform calibration, please log out and then log in at the
administrator access level.
Do as follows to calibrate the analyzer.

On the "Manual” calibration screen, check the calibration factors and calculate the new
factors per the following equation:
Current calibration factor × Reference value
New calibration factor＝
Mean
For example: Suppose the WBC reference value of a calibrator is 8.4, and the current
calibration factor of the whole blood mode is 98.90％.
Run the calibrator under the whole blood mode for 10 consecutive times and take the WBC
results to calculate: 8.1, 8.0, 8.1, 8.1, 8.3, 8.3, 8.2, 8.0, 8.1, 8.3. The obtained CV is 1.5% and
Mean is 8.16, which meet the requirements.
8-4
The new calibration factor is obtained:

98.90% × 8.4
New calibration factor＝＝101.81%
8.16
The calculated calibration factors shall be between 75.00％～125.00％. In case of an invalid

calibration factor, try to find out the reason (e.g. calibration material not thoroughly mixed,
misoperation, etc.). Then recalibrate the analyzer and recalculate the calibration factors.
Enter the new calibration factors into the factor cell of the parameter that require calibration.
When you switch screen after entering the new calibration factor, a prompt will display.
 If the entered calibration factors are valid, a dialog box will pop up asking you to save the
new factor when you are exiting the screen. And the calibration date of the
corresponding parameter changes to current system date.
 If the entered calibration factors are invalid, a dialog box will pop up prompting "Invalid
entry" when you are switching to another screen. The new calibration factor will not be
saved, and the calibration date will not be refreshed.
Other Operations
 Print
Tap "Print" to print the current calibration factor.

If the calibration factors are invalid, you will not be able to print them and the dialog box "New
calibration factor is invalid." will display.
If the calibration factors are valid but not saved, a dialog box will display asking you to save
the factors.
Tap "Yes" to save and print the factors. Or Tap "No" to cancel the operation without saving or
printing them.
8-5
8.3.3 Calibration with Calibrator

Tap "Calibration" > "Calibrator" in the menu to enter the following screen.
NOTE
 The calibrator calibration can only be performed under whole blood mode.
 Only Mindray-specified calibrators shall be used. Mindray will not be

responsible for any erroneous result caused by using other calibrators.
 See the instruction for use of the calibrators for the lot No., expiration date
and the target.
 The out-of-range CV% does not influence the display of calibration factors.
Do as follows to calibrate the analyzer with calibrators.

1. Check the mode on the analyzer screen.
2. Enter the lot No. of the calibrator into the "Lot No." box.
3. Enter the “Exp. Date”. The expiration date defaults to the current system date. When you
need to modify it, tap the "Exp. Date" edit box, and reset the date. The expiration date
shall not be earlier than the current system date.
4. The entered expiration date should be either the expiration date printed on the
instructions for use or the open-container expiration date, whichever is earlier. The
open-container expiration date is calculated as follows: the date that container is opened
+ the open-container stability days.
5. Enter the targets into the "Target" cells.
8-6
6. Prepare the calibrator as instructed by instructions for use of the calibrators.

7. Press the [Aspirate] key to start calibration.
8. After the analysis, the progress bar will close. The analyzer will have different responses
to different analysis results.
9. When the current running is done, if there is a parameter whose calibration data is out of
its linearity range but still within the display range, then the calibration data will be
displayed in the list and a message box will also pop up.
Tap “OK” to close the message box, and the data will be deleted from the table without
saving automatically.
10. When the running is done, if there is a parameter whose calibration data is out of the
display range, then the non-numeric parameter values "***" will be displayed in the list
and a message box will pop up.
 The valid results within the linearity range will be displayed directly. Valid calibration
results will be marked with "√” per the default setting, and will be taken to calculate
calibration factors.
11. If the calibration factors have not been calculated but you switch to another screen, then
a message box will pop up.
8-7
Tap "Yes" to switch to another screen while discarding the calibration data and closing
the message box. The original calibration factors remain.
12. When calibration count has been performed to a sample for n times (n≥5), the analyzer
will calculate the Mean, CV% and calibration factors of all the calibration data marked
with "√" (calibration data of the first run is not marked with "√", so it is not included in the
calculation).
You can select several data to calculate the calibration factors, but only after at least 5
groups of the data are marked with "√" can you get the calibration factors. The
calibration factors will be refreshed whenever you select “√” or deselect “√”.
When the amount of valid calibration data in the list reaches 10, a message box
"Calibration is completed!" will pop up. Then, if you press the [Aspirate] key again, the
analyzer will beep without starting analysis.
13. There may be two cases when you are switching to another screen:
If the calibration factors of any parameter is out of the range [75%-125%] or the CV% of
any parameter exceeds the reproducibility range, then the calculated calibration factors
of all parameters will not be saved and a message box will also pop up.
Tap "Yes" to close the dialog box and switch to another screen. The calibration factors
and dates of all parameters will not be changed.
If the calculated calibration factors of all parameter are within the range [75%-125%] and
the CV% of all parameter are also within the reproducibility range, then a message box
will pop up.
Tap "Yes" to save the new calibration factors while closing the message box and
switching to another screen.
8-8
Other Operations
 Print
If the calibration factors are invalid, tap print, the dialog box "New calibration factor is
invalid." will display.
If the calibration factors are valid, tap "Print", a dialog box will display.
Tap "Yes" to close the dialog box, save and print the calibration results. Or tap "No" to cancel
the operation without saving or printing them.
8.3.4 Calibration with Fresh Blood

Tap "Calibration" > "Fresh Blood" in the menu to enter the following screen.
Do as follows to calibrate the analyzer with fresh blood.
8-9
1. Prepare 3 to 5 normal fresh blood samples as instructed in Chapter 5 Operating Your

Analyzer.
2. Run each of the prepared samples on the reference instrument (or by the reference
method) five times at least. Calculate the mean values and use them as the targets. Or
perform measurement and calculation as per the reference method and take the
calculated data as the targets.
3. Tap the “Mode” button, and select the radio button “WB” or “PD” as the desired mode
4. Select the ID of current sample from the pull-down box "Current Sample ID".
5. Select the parameter to be calibrated from the check box on the first line of the list.
6. Enter the targets into the "Target" cells.
7. Prepare fresh blood sample.
8. Press the [Aspirate] key to start calibration.
9. After the analysis, the progress bar will close. The analyzer will have different responses
to different analysis results.
 If the results are out of the linearity range but still within the display range, a dialog box
will pop up when the results are displayed in the table.
 If the results are out of the display range, the non-numeric parameter values "***" are
obtained and a dialog box will pop up.
 The valid results within the linearity range will be displayed directly.
Valid calibration results will be marked with "√” per the default setting, and will be taken
to calculate calibration factors.
8-10
10. When calibration count has been performed to a sample for n times (n≥5), the analyzer
will calculate the Mean, CV% and calibration factors of all the calibration data marked
with "√" automatically.
You can select several data to calculate the calibration factors, but only after at least 5
groups of the data are marked with "√" can you get the calibration factors. The
calibration factors will be refreshed whenever you select “√” or deselect “√”.
When the amount of valid calibration data in the list reaches 10, a message box
"Calibration with the current blood sample is completed." will pop up when you start
calibration again.
11. Select other calibration sample ID from the "Current Sample ID" pull-down box, analyze
other samples according to Step 8～10 above to obtain the calibration factors of all
samples.
12. There may be several cases when switching to another blood sample:
 If the calibration factors of the blood sample are invalid or the CV% of any parameter
exceeds the reproducibility range, a dialog box will pop up when switching to another
blood sample.
Tap "Yes" to empty the entered target of the current sample, all the calibration data
obtained and each calculated value including calibration factors, then close the dialog
box and switch to another blood sample.
 If the calibration factors have not been calculated, a dialog box will pop up.
Tap “Yes” to empty the entered target of the current sample and all the calibration data
obtained, then close the dialog box and switch to another blood sample.
 If the calibration factors of the sample are valid and the CV% of all the parameters do not
exceed the reproducibility range, you can switch to another blood sample directly.
13. After calibration factors of at least 3 fresh blood samples are obtained, tap the "Calculate"
8-11
button to enter the screen of calibration calculation.
Select or deselect the calibration factors of a blood sample for the calculation of the
Mean calibration factors by tapping the check boxes before the calibration factors.
When 3 or more groups of calibration factors are checked, CV% will be re-calculated
automatically base on the checked calibration factors.
When 3 or more groups of calibration factors are checked, the mean calibration factor
will be re-calculated automatically base on the checked calibration factors. The mean
calibration factors are regarded as invalid if the deviation of absolute value between the
calibration factors included in calculating the mean and the original calibration factors
reaches or exceeds 5%; a dialog box will pop up when you exit the current fresh blood
calibration screen.
Tap "Yes" to close the dialog box and exit with the current calibration data emptied, and
then switch to another screen.
Tap "No" to return to the current screen. Invalid mean calibration factors are followed
with a "?". and displayed in red.
14. If the mean calibration factors have not been calculated, when you exit the fresh blood
screen or switch to another calibration mode, a dialog box will pop up.
8-12
Tap "Yes" to discard the calibration data, close the dialog box, and switch to another
screen or calibration mode. The original calibration factors and date remain the same.
15. If the calculated mean calibration factors are valid, when exiting the fresh blood
calibration screen or switching to another calibration mode, a dialog box will pop up.
Tap "Yes" to save the current mean calibration factors. Then, you can switch to another
screen or calibration mode. Tap "No" to close the dialog box and switch to another
screen or calibration mode without saving the mean calibration factors and all the
calibration data.
Other Operations
 Print
If the mean calibration factors are invalid, tap print, the dialog box "Calibration factor is
invalid." will display.
If the mean calibration factors are valid, you can tap "Print" to print the calibration factors of a
group (or more) of blood samples in table form, no matter whether they are selected ("√") or
not. The results obtained in the calibration process and the mean calibration factors can also
be printed.
8-13
9 Customizing the Analyzer Software
9.1 Introduction
The analyzer is a flexible laboratory instrument that can be tailed to your work environment.
You can use the “Setup” program to customize the software options as introduced in this
chapter.
Menu functions are introduced as below.
See the following figure for the setup menu.
9-1
Customizing the Analyzer Software
9.2 System Setup

9.2.1 System Setup
 Date/Time Setup
Tap the menu option "Setup" > "System Setup" > "Date/Time Setup" to enter the
"Date/Time Setup" screen as shown below. You can set up the date, time and date format of
the analyzer at the screen.
 Print Setup
Tap the menu option "Setup" > "System Setup" > " Print Setup" to enter the "Print setup"
screen as shown below. You can set up the following contents:
 Print Setup
 Printing content
 Auto print after sample analysis
9-2
 Print Setup
Print Device
You can select "Printer" or "Recorder" from the "Print Device" pull-down list.
Print Drive
Tap the pull-down list to select print drive of the analyzer.
Paper
Tap the pull-down list to select the paper type of the reports to be printed.
Para. language
Tap the pull-down list to select the parameter language of the reports.
Copies
Enter the number of copies to be printed for each report into the edit box "Copies".
Report title
9-3
Report template
 Printing content
You can choose to select the functions based on your needs by tapping on the check boxes.
 Auto print after sample analysis
You can choose to disable auto print or set up printing conditions.
 Communication Setup
Tap the menu option "Setup" > "System Setup" > "Communication" to enter the
communication setup screen as shown below. You can set up the following contents:
 Communication
 Network Device
 Protocol Setup
 Transmission Mode
9-4
 Communication
You can select "Network port comm." or "Serial port comm.".
 Network Device
You can select "Wireless" or "Wired" from the "Network Type" pull-down list.
If you select "Wireless", tap the wireless network setup icon , and choose a WiFi hot
spot from the popped out dialog box to establish connection.
 Protocol Setup
Tap the "IP Address", "Subnet Mask" and "Default Gateway" edit boxes to enter the
contents.
Communication Protocol
Tap the "Comm. Protocol" pull-down list to select the communication protocol.
 Transmission Mode
You can select the functions based on your needs by tapping on the check boxes.
 Auto retransmit
 Auto comm.
 Transmit as Print Bitmap Data
 ACK synchronous transmission
9-5
 ACK synchronous transmission
Tap on the "ACK synchronous transmission" check box to activate the function.
When the function is activated, ACK overtime is 10 seconds by default. You can re-enter the
ACK overtime is the edit box.
 Transmission mode of histogram
Tap the pull-down lists to select the transmission modes of histogram.

 Not to be transmitted
 Bitmap
 Data
 Shortcut Code Setup

Tap the menu option "Setup" > "System Setup" > "Shortcut Code Setup" to enter the
screen as shown below. This function allows you to set up shortcut codes for the contents on
the "Next Sample" screen and the "Edit Info" screen of "Grap Review".
 Add shortcut codes
1. Select "Dpt." or "Orderer by" tab.
2. Tap "Add", a line will be added in the table.

3. Enter the "Name", "Shortcut Code" and "Digital Code" based on your needs.
9-6
 Edit shortcut codes
1. Select "Dpt." or "Orderer by" tab.

2. Select the line of the shortcut code to be edited.
3. Modify it directly in the table.
 Delete shortcut codes
1. Tap the shortcut code to be deleted.

2. Select the line of the shortcut code to be deleted.
3. Tap "Delete" to delete it.
 Lab info. setup

Tap the menu option "Setup" > "System Setup" > "Lab Info. Setup" to enter the screen as
shown below. Operators may enter, save and view lab information. Tap on the edit boxes to
enter the information.
NOTE
 The analyzer SN cannot be edited.
 The date of installation is the date the analyzer is installed by default. It can
be edited, but cannot be later than the current system date.
9-7
9.2.2 User Management

Tap "Setup" > "Access Setup" in the menu to enter the following screen.
 Modify password
You can modify your own password.

1. Select the current user, and then tap "Modify Password", the following dialog box
will display.
2. Enter the required information in the text boxes.

3. Tap "OK" to save the change and close the dialog box.
9-8
NOTE
 Up to 12 characters can be entered.
 Add a new user
1. Tap "New", the following dialog box displays.
2. Enter the "User ID", "Name" and "Password" information. The "User ID" refers to
your login account; and the "Name" will be displayed in the "Operator" or
"Validated By" fields on the "Table Review" screen and on the printed reports.
3. Select access level of the user:
 Administrator
 Operator
4. Tap "OK" to save the change and close the dialog box.
NOTE
 The user ID cannot be null and up to 12 characters can be entered.
 The password cannot be null and up to 12 characters can be entered.
9-9
 The name cannot be null and up to 20 characters can be entered.
 Deleting a User
Select a user and then tap "Delete" to delete it.
NOTE
 The current login user cannot be deleted.
9.2.3 Auxiliary Setup

Tap "Setup" > "Auxiliary Setup" in the menu to enter the following screen. You can set up
the following contents:
 Setting of the next sample
 Setting of the first sample after startup
 Other settings
 Setting of the next sample
Entry of the next sample ID

Tap the pull-down list to select the way to enter the next sample ID.
 Auto Increase
 Manual Entry
9-10
Not counted as an auto increase character

You can set up the number of characters in the sample ID that will not be auto increased.
When "Auto Increase" is selected as the way to enter the next sample ID, this edit box will
be activated.
Enter a number (n) into the edit box of "Not counted as an auto increase character". The
first n characters in the sample ID will not be auto increased.
 Setting of the first sample after startup
You may customize the first sample ID after startup by entering it into the edit box; or select to
continue with the sample ID before last shutdown.
 Other settings
On/Off radio buttons
 Select "On" or "Off" to activate or deactivate the functions.
Flags
You may set up the suspect flag by entering a character into the edit box, or selecting a letter
from the pull-down list (the default character is "R").
You may set up the high/low flag by entering characters in the edit boxes, or selecting letters
from the pull-down lists (the default character of high flag is "H", and that of low flag is "L").
9-11
9.2.4 Setting Parameters

 Parameter unit setup
Tap the menu option "Setup" > "Parameter Setup" > "Reference Unit Setup" to enter the
screen as shown below. You can set up parameter units on this screen.
 Select unit system
Tap the "Unit System" pull-down list to select unit system.
 Customizing parameter units
Under each unit system, you can tap the "Unit" cell to customize the parameter unit.
Tap the "Default" button to restore the default units.
NOTE
 The units displayed will be different when different unit system is selected.
 Reference range setup

Tap the menu option "Setup" > "Parameter Setup" > "Reference Range Setup" to enter the
screen as shown below. 5 factory reference groups and 10 customized reference groups are
provided for your choice. Each laboratory shall select a proper reference range of its own
based on its patient demographics. The reference range differs among races, genders, ages
and geographic locations.
9-12
 Customizing reference groups
Select a reference group and tap "New" or "Edit" to enter the reference group setup screen.
You can set up the name, lower and upper limits of age and reference range.
Tap the "Set to Default" button, the reference ranges of the selected factory reference group
can be restored to the default settings.
9-13
NOTE
 The name of the reference group cannot be null.
 The names of the customized reference groups shall not repeat the names
of the 5 default groups (General, Adult male, Adult female, Child, and
Neonate) and they shall not repeat each other either.
 Setting as default reference group
Select a reference group and then tap "Set to Default" to set it as default reference group.
NOTE
 The name, lower and upper limits of age and gender of the factory reference
groups cannot be modified.
 The input range of age is [0,999].
 Modify reference range(s)
To modify the reference range of a reference group, select the group from the reference
group list on the left, and then tap the cells of upper and lower limits in the table and re-enter
the values.
To restore the reference ranges to default, tap the “Default” button on top right of the screen.
Select "Match customized ref. group first", when the age ranges of the customized
reference group and the default reference group contradicts with each other, the customized
reference group will be matched first on the sample analysis and review screens.
9-14
9.2.5 Maintenance Setup (for administrators only)

Tap "Setup" > "Maintenance" in the menu to enter the following screen. You can set up the
following contents:
 Standby
Tap the text box "Wait" and enter the waiting time before entering the standby status. The
range allowed is 10 -30 minutes, and the default setting is 15 minutes.
 Probe cleanser maintenance

Tap the "Time-based daily maintenance" text box in the "Probe Cleanser Maintenance"
area to enter the time to start time-based probe cleanser maintenance. Enter a time to the
"Remind every" text box. Then when the operator cancels the time-based maintenance, a
reminder dialog box will pop up after the defined minutes.
9-15
9.2.6 Reagent Management

Tap "Setup" > "Reagent Setup" in the menu to enter the following screen.
This function may also be used to refill reagent inside the fluidic system when a new
container of reagent is loaded.
NOTE
 The diluent must be kept still for at least a day after long-term
transportation.
 When you have changed the diluent, lyse or rinse, run a background to see
if the results meet the requirement.
You should replace reagents when:
 the reagent ran out and a new container of reagent is installed.
 the reagent in the tubing is contaminated.
 there are bubbles in the tubing.
You can replace the following reagents in the fluidics:
 Diluent
 Lyse
9-16
Do as follows to replace the reagents.

1. Enter reagent information at the screen.
2. Or enter the barcode by scanning. If the barcode is valid, the corresponding reagent
information will automatically display.
3. Tap "Apply" to save the exp. date and start to replace the reagent. A progress bar will be
displayed in the process.
4. Replace other reagents as per the above procedures if needed.
9.2.7 Gain Setup (for administrators only)

Tap "Setup" > "Gain Setup" in the menu to enter the following screen. Gain setup function
allows you to adjust the digital potentiometers. The operation shall not be performed
frequently.
 Setup
 HGB gain
The purpose of adjusting HGB gain is to change HGB background voltage.

Tap the "Set to 4.2V" button, and the HGB blank voltage will be set to 4.2V automatically.
9-17
9.3 Save the settings

To save the modified settings, you may switch to another screen, the following dialog box will
display.
Tap "Yes" to save the settings and switch to the corresponding screen. Tap "No" to switch to
the corresponding screen without saving the settings.
9-18
10 Servicing Your Analyzer
10.1 Introduction
Preventive and corrective maintenance procedures are required to keep the analyzer in a
good operating condition. This analyzer provides multiple maintenance functions for this
purpose.
This chapter introduces how to use the provided functions to maintain and troubleshoot your
analyzer.
 All the analyzer components and surfaces are potentially infectious, so take
proper protective measures for operation and maintenance.
WARNING
 Stop using the instrument when you find any fluid tubing or part filled with
fluid is aging or wearing, and contact the service engineer or your local
distributor to replace.
 When the instrument is waiting for service, it is suggested that sterilize and
clean the potentially bio-hazardous parts (instrument surface, sample
probe, etc.), in order to reduce the risk of bio-hazard or other hazards while
transporting or servicing the instrument.
CAUTION
 Improper maintenance may damage the analyzer. Operators must follow the
instruction of this Operator's Manual to perform maintenance operations.
 For any questions, contact Mindray customer service department.
 Only Mindray-supplied parts can be used for maintenance. For any

questions, contact Mindray customer service department.
 Exercise caution to avoid contact with the sharp sample probe when
performing maintenance.
The following table lists the tools that may be used in maintenance.
No. Tools
1. Cross-headed screwdriver
Servicing Your Analyzer
2. Slotted head screwdriver

3. Medical gloves
4. Alcohol
10-2
10.2 Maintaining Your Analyzer

Maintenance options of the analyzer includes: maintenance, cleaning and fluidics
maintenance.
10.2.1 Maintenance
Tap "Service" > "Maintenance", and select the "Maintenance" tab to enter the following
screen.
Unclogging
Unclogging includes zapping and flushing the aperture. When clog error us reported, you
should unclog the aperture.
The unclogging procedures are:
1. Tap the "Unclog" button to start unclogging.
2. When the progress ends, a message will display indicating "Maintaining
finished!".
3. Do the above procedures to continue unclogging aperture if necessary. If the
error persists, perform probe cleanser maintenance of the related channels.
Overall Soak
You should perform the overall soaking procedure with the probe cleanser when:
 background results are outside the specified range, QC results abnormal due to long
term idleness of the analyzer; or when other maintenance operations fail to solve the
clog error.
 the analyzer shuts down due to abnormal power break-off; probe cleanser maintenance
10-3
must be performed after it is started up again.
The overall soak maintenance procedures with the probe cleanser are as below:
1. Tap the "Overall Soak" button, the following dialog box will display.
2. Tap "Yes", the analyzer starts to prepare for the maintenance.

3. When the preparation is done, the following dialog box will display.
4. After aspirating probe cleanser, the analyzer performs probe cleanser soak
automatically, and a progress bar will display indicating the progress.
5. When the progress ends, the following dialog box will display, tap “OK” to close the
dialog box.
10-4
10.2.2 Cleaning
You should clean the following components when:
 WBC and (or) HGB background results exceed their limits, perform WBC bath cleaning.
If WBC bath cleaning does not solve the problem, perform WBC probe cleanser
maintenance.
 RBC and (or) PLT background results exceed their limits, perform RBC bath cleaning. If
RBC bath cleaning does not solve the problem, perform RBC probe cleanser
maintenance.
 sample probe gets dirty, perform sample probe cleaning.
Tap "Service" > "Maintenance", and select the "Cleaning" tab to enter the following screen.
You may perform cleaning operation to the following components:
 Analyzer
 Sample probe
 WBC bath
 RBC bath
The cleaning procedures are:

1. Tap the button of the component you want to clean. The message "Cleaning in
process. Please wait..." will display.
10-5
2. When the progress ends, a message will display indicating "Cleaning finished!".
3. Clean other components as per the above procedures if needed.
10.2.3 Overall Maintenance

Tap "Maintenance", and select the "Fluidics" tab to enter the following screen.
Pack-up
If the analyzer is not to be used for over 2 weeks, you should perform this procedure.
Do as follows to pack up:
1. Tap "Pack-up", the dialog box "Start pack-up?" will pop up.
2. Tap "Yes" to perform the pack-up procedure. The following dialog box will be
displayed.
3. Remove all reagent pickup tube assemblies according to the prompt, and then Tap
the “OK” button to start emptying the fluidic system.
10-6
4. After the emptying is complete, a message box will pop up.
5. Place all reagent pickup tube assemblies into the distilled water, and then tap the
“OK” button to start priming.
6. After the cleaning is done, a message box will display.
7. Remove all reagent pickup tube assemblies according to the prompt, and then tap
the “OK” button to start emptying the fluidic system for the second time.
10-7
8. After the emptying is complete, a message box will display.
9. You should turn off the power switch according to the prompt displayed on the
screen.
NOTE
 This software can still be used after the pack-up.
Resetting the Fluidics

When major components of the analyzer have been replaced, or the fluidic system has been
serviced, you must reset the fluidics. Do as follows:
1. Tap "Reset Fluidics", a dialog box will pop up asking you to comfirm the operation.
2. Tap "OK" to start initialization, the message "Resetting fluidics. Please wait..." will
be displayed.
3. When the progress ends, a dialog box will display indicating “Resetting fluidics
finished!”.
4. Do the above procedures to continue resetting fluidics if necessary.
10.3 Self-Test
Select “Maintenance”> “Self-Test” from the pull-down menu to enter below screen and
perform system and valve self-tests.
10-8
10-9
10.4 Gain Calibration

Select “Maintenance”> “Gain Calibration” from the pull-down menu to enter below screen and
calibrate the gains.
10-10
10.5 Advanced Toolbox

Select “Maintenance”> “Advanced Toolbox” from the pull-down menu to enter below screen,
where you can switch the languages and perform one-key export.
10-11
10.6 Sample Probe Debug

Select “Maintenance”> “Sample Probe Debug” from the pull-down menu to enter below screen,
where you may initialize the sample probe position and fix the probe height.
10-12
10.7 Touch Screen Calibration

Tap "Maintenance" > "Calibrate Touchscreen" in the menu to enter the following screen.
10-13
10.8 Viewing Logs

Tap "Maintenance" > "Touch Screen Calibration" in the menu to enter the following screen.
You may view the error info., parameter modification info. and records of daily operation in
the log.
The “Log” screen records all activities of the analyzer. It contributes significantly to searching
for operation history and troubleshooting the analyzer.
NOTE
 The oldest record will be overwritten automatically when number of log
records reaches the utmost.
 Records of two years can be stored at most.
10-14
 Exporting logs
1. Tap "Export", the following dialog box will display.
2. Select the range of the logs that you want to export.

3. Tap "OK" to close the dialog box and export the logs.
10-15
10.9 Checking the Analyzer Status
NOTE
 If the status is outside normal range, it will be highlighted with red
background.
10.9.1 Counter
You can check detailed statistics on the screen, for example, running times of the analyzer
and the valid sample runs.
 Viewing details
You may tap the "Detail..." buttons following "Sample Runs", "QC Runs" or "Calibration
Runs" to view the related details.
 Print
Tap the "Print" icon to print all information on the screen.
10-16
10.9.2 Temperature and pressure

Tap "Status" > "Temp.&Pressure" in the menu to enter the following screen. You may check,
export or print the temperature and pressure values of different components of the analyzer.
10.9.3 Voltage
Tap "Status" > "Voltage" in the menu to enter the following screen. You may view the current
voltage of the analyzer.
10-17
10.9.4 Sensor
Tap "Status" > "Sensor" in the menu to enter the following screen. You may view the current
sensor information of the analyzer.
10.9.5 Version information

Tap "Status" > "Version Info." in the menu to enter the following screen. You may view the
current version information of the analyzer.
10-18
11 Troubleshooting Your Analyzer
11.1 Introduction
This chapter contains information that is helpful in locating and correcting problems that may
occur during operation of your analyzer.
 Samples, controls, calibrators and waste are potentially infectious. Wear

proper personal protective equipment (e.g. gloves, lab coat, etc.) and follow
safe laboratory procedures when handling them and the contacted areas in
the laboratory.
NOTE
 This chapter is not a complete service manual and is limited to problems
that are readily diagnosed and/or corrected by the user of the analyzer.
11-1
Troubleshooting Your Analyzer
11.2 Error Information and Handling

During the operation, if error(s) is/are detected, the analyzer will beep and display the
corresponding error message in the error information area at the bottom right of the screen.
Meanwhile, the indicator will turn red.
According to the severity of the errors, the colors of error messages are red, orange, blue.
 Red: fatal error. When this kind of error occurs, the analyzer will stop running
immediately, and any further operation is prohibited.
 Orange: error that stops operation. When this kind of error occurs, the analyzer will stop
running immediately.
 Blue: error that restricts certain operations. When this kind of error occurs, the analyzer
can still continue with the current operation, but any other operations related to the error
will be restricted.
The following Figure is the error info. dialog box.
The name and troubleshooting method of the errors are displayed. Names of the errors are
displayed by the order of their occurrence.
You may tap to select the error, and view its troubleshooting information in the
troubleshooting box. The troubleshooting information of the first error is displayed by default.
Follow the instruction in the dialog box to remove error(s).
The following functions are provided:
11-2
 Remove
Tap the "Remove " button to clear all the errors that can be removed automatically. For the
errors that cannot removed automatically, follow the troubleshooting method to solve them.
 Close the error info. dialog box
Tap "Close" to close the dialog box, but the errors will still be displayed in the error info. area
on the screen. Tap the error info. area again, the dialog box will be displayed.
The possible error(s) and the corresponding troubleshooting information are listed below:
Error name Actions

1. Power off the analyzer directly and contact our customer
Main board error
service department.
System clock error
service department.
1. Tap "Remove ", and enter the new barcode of the diluent into
the reagent setup dialog box.
2. After replacing the diluent container, tap "Apply" to prime the
Diluent ran out
diluent.
3. If the problem still persists after replacing the diluent, contact
our customer service department.
Diluent ran out
diluent.
1. Tap "Remove ", and enter the new barcode of the lyse into the
reagent setup dialog box.
Lyse ran out 2. After replacing the lyse container, tap "Apply" to prime the lyse.
3. If the problem still persists after replacing the lyse, contact our
customer service department.
Lyse ran out 2. After replacing the lyse container, tap "Apply" to prime the lyse.
Diluent expired
diluent.
11-3
Lyse expired 2. After replacing the lyse container, tap "Apply" to prime the lyse.
1. Empty the waste container or use a new waste container.
2. Tap“Remove” to see if the error can be removed.
Waste container full
3. If the problem still persists, contact our customer service
department.
Power error
service department.
Syringe module error 2. If the problem still persists, contact our customer service
department.
Aspiration module lift
mechanism error
department.
Aspiration module 1. Tap“Remove” to see if the error can be removed.
rotary mechanism 2. If the problem still persists, contact our customer service
error department.
Background abnormal 2. If the problem still persists, contact our customer service
department.
HGB background
voltage abnormal
department.
Vacuum pressure
abnormal
department.
Diluent temperature 1. Diluent temperature must be within [10℃, 40℃].
goes beyond higher
limit
Diluent temperature 1. Diluent temperature must be within [10℃, 40℃].
goes beyond lower
limit
Preheat bath
temperature is too high
department.
Preheat bath
temperature is too low
department.
Clogging (WBC) 2. If the problem still persists, contact our customer service
department.
11-4

Clogging (RBC) 2. If the problem still persists, contact our customer service
department.
Aperture voltage
abnormal (WBC)
department.
Aperture voltage
abnormal (RBC)
department.
1. Please check whether there is no paper or paper jam.
2. Tap "Remove" to remove automatically.
No paper or paper jam
3. If the problem persists when you try to print again, contact our
Other printer error 2. If the problem persists when you try to print again, contact our
1. No paper in recorder. Please install a new roll.
No paper in the
recorder or recorder
3. If the problem persists when you try to print again, contact our
cover open
Recorder error 2. If the problem persists when you try to print again, contact our
1. Communication disconnected. Please check the network
connection.
Communication
disconnected
3. If the problem persists when you try to communicate again,
contact our customer service department.
Communication error 2. If the problem persists when you try to communicate again,
contact our customer service department.
11-5
11-6
12 Appendices
A Index
Prediluted Sample, 5-8
A
Analysis, 5-10 Q
Aspiration, 3-2 Quality Control, 7-1
B R
Buzzer, B-4 Reagents, 2-11
Recorder, B-4
C Install Paper, 4-9
Calibration, 8-1
Calibrator, 2-11 S
Capillary whole blood samples, 5-8 Self-Test, 5-4
Colorimetric Method, 3-7 Setup, 9-2
Controls, 2-11 Shutdown, 5-18
Software, 9-1
D Standby, 5-16
Dilution, 3-3 Startup, 5-4
G T
Graph Review, 6-3 Table Review, 6-2
Touch Screen, B-4
I Transmission, 7-10
Troubleshooting, 11-1
Impedance Method, 3-8
Initial Checks, 5-2
W
Installation, 4-2
Whole Blood Samples, 5-8
L
Login, 5-4
Logs, 10-9
M
Maintenance, 10-2
Manual Calibration, 8-4
P
Parameter flag, 5-15
Parameters, 2-2
A-1
B Specifications
B.1 Classification
According to the CE classification, the BC-20s belongs to In vitro diagnostic medical devices
other than those covered by Annex II and devices for performance evaluation.
B.2 Reagents
Diluent M-30D Diluent
Lyse M-30CFL Lyse
Probe Cleanser Probe Cleanser
Controls (Impedance Method) B30 and BC-3D
Calibrators (Impedance Method) S30 and SC-CAL PLUS
B.3 Applicable Tubes

Ф12～15×75mm evacuated collection tube (without cap) for whole blood mode
Ф11×40mm (1.5ml centrifugal tube) and 0.5ml centrifugal tube, for predilute and capillary
whole blood mode
Ф10.7×42mm small closed anticoagulated tube (without cap), 0.5ml, can be used with cap
opened, for capillary whole blood mode. Recommended tube: No. 365974 closed
anticoagulated tube (0.5ml) manufactured by BD.
B.4 Parameters
Name Abbreviation Default Unit
9
White Blood Cell count WBC 10 /L
9
Lymphocyte number Lymph# 10 /L
9
Mid-sized Cell number Mid# 10 /L
9
Granulocyte number Gran# 10 /L
Lymphocyte percentage Lymph% %

Mid-sized Cell percentage Mid% %
Granulocyte percentage Gran% %

12
Red Blood Cell count RBC ×10 /L
Hemoglobin Concentration HGB g/L
Mean Corpuscular Volume MCV fL

Mean Corpuscular
Hemoglobin MCH pg
Mean Corpuscular MCHC g/L

B-1
Appendices
Hemoglobin Concentration
Red Blood Cell Distribution

Width Coefficient of Variation RDW-CV %
Red Blood Cells Distribution
Width - Standard Deviation RDW-SD fL
Hematocrit HCT %
9
Platelet count PLT ×10 /L
Mean Platelet Volume MPV fL
Platelet Distribution Width PDW /
Plateletcrit PCT %
B.5 Sampling Features
B.5.1 Sample Volumes Required for Each Analysis

Whole blood mode ≤ 9μL
Predilute mode ≤ 20μL
B.5.2 Throughput
Whole blood mode The throughput shall be no less than 40 samples/hour
Predilute mode The throughput shall be no less than 40 samples/hour
B.6 Performance Specifications
B.6.1 Display Ranges for Major Parameters
Parameter Display range
(0.0 ~ 999.9) × 10 /L
9
WBC
(0.00 ~ 9.99) × 10 /L
12
RBC
HGB (0 ~ 300) g/L

MCV (0.0 ~ 250.0) fL
(0 ~ 9999) × 10 /L
9
PLT
B.6.2 Blank Count Parameter Specifications

Parameter Requirement
≤ 0.2 × 10 / L
9
WBC
≤ 0.02× 10 / L
12
RBC
HGB ≤1g/L
B-2
Appendices
HCT ≤ 0.5 %
≤ 5× 10 / L
9
PLT
B.6.3 Linearity Range

Parameter Linearity range Deviation Range Deviation Range
(Whole Blood) (Predilute)
9 9 9
WBC (0～100.0)×10 /L ±0.30×10 /L or ±5％ ±0.50×10 /L or ±5％
±9% ±18%
12 12 12
RBC (0～8.00)×10 /L ±0.05×10 /L or ±5％ ±0.05×10 /L or ±5％
HGB (0-280)g/L ±2g/L or ±2％ ±2g/L or ±3%

9 9 9
PLT (0～1000)×10 /L ±10×10 /L or ±10% ±10×10 /L or ±10%
HCT (0～67)% ±4% (HCT value) or /

±6% (percentage
error)
B.6.4 Reproducibility
Reproducibility range (whole blood)

Parameter Condition CV%
9
(7.0 ~ 15.0)× 10 / L ≤ 2.0%
WBC
(4.0 ~ 6.9) × 10 / L
9 ≤ 3.5%
RBC (3.50 ~ 6.50) × 10 / L

12
≤ 1.5%
HGB (100 ~ 180) g/L ≤ 1.5%
MCV (70.0~ 110.0) fL ≤ 1.0%
(150 ~ 500) × 10 / L
9
≤ 4.0%
PLT
9
(100~149)× 10 / L ≤ 5.0%
B.6.5 Carryover
Parameter Carryover
WBC ≤0.5％
RBC ≤0.5％
HGB ≤0.5％
PLT ≤1.0％
B-3
Appendices
B.6.6 Error of Indication
Parameter Error of indication

WBC ≤±10％
RBC ≤±6％
HGB ≤±7％
PLT ≤±15％
B.7 Input/Output Devices

B.7.1 Touch screen
8 inch TFT color touch screen, supporting 24 bit color at highest, with display resolution of
800×600.
B.7.2 Indicator
The indicator indicates analyzer the status of the analyzer, including on/off, running or
sleeping.
B.7.3 Keyboard (Optional)

101-Key alpha-numeric USB keyboard
B.7.4 Mouse(Optional)
USB mouse.
B.7.5 Barcode scanner (Optional)

External USB barcode scanner
B.7.6 Printer (Optional)

Supports USB printer.
B.7.7 Recorder
A thermal recorder is included.
B.7.8 Buzzer
The buzzer sounds when there is an error. Tap the touch screen or when the error is removed,
the buzz alarm will be silent automatically,
B.7.9 USB WiFi wireless network card (optional)

WiFi wireless network card with chip RTL8192CU
B-4
Appendices
B.8 Interfaces
 One network interface, built-in network card, network access and TCP/IP compatible.
 4 USB ports
B.9 Power supply

Voltage Input power Frequency
Analyzer (100V-240V～) ±10% 300 VA (50/60Hz)±1Hz
B.10 Fuse
WARNING
 Only install fuses of specified specification on the system and the
pneumatic unit.
Fuse: 250V T3.15AH
B.11 EMC Description

 Do not use this device in close proximity to sources of strong electromagnetic
radiation (e.g. unshielded intentional RF sources), as these may interfere with the
proper operation.
 This equipment complies with the emission and immunity requirements of the EN
61326-1:2006 and EN 61326-2-6:2006.
NOTE
 Only install fuses of specified specification on the system and the
pneumatic unit.
 It is the manufacturer's responsibility to provide equipment electromagnetic

compatibility information to the customer or user.
 It is the user's responsibility to ensure that a compatible electromagnetic

environment for the equipment can be maintained in order that the device
will perform as intended.
B.12 Sound Pressure

Maximal sound pressure: 65 dB
B-5
Appendices
B.13 Environment Requirements

 Ambient temperature: 10℃～35℃
 Operating humidity: 20%～85%
 Atmospheric pressure: 70.0kPa～106.0kPa
B.14 Storage Environment

 Ambient temperature: -10℃～40℃
 Relative humidity: 10%～90%
B.15 Operating Environment

 Ambient temperature: 10℃～40℃
 Relative humidity: 10%～90%
NOTE
 Be sure to use and store the analyzer in the specified environment.
B-6
Appendices
B.16 Dimensions and Weight
Height
Depth
Width
Analyzer
Width (mm) ≤300
Height (mm) ≤400 (foot pad included)
Depth (mm) ≤410
Weight (Kg) ≤20
B.17 Contraindication
None
B.18 Safety Classification

Level of transient overvoltage: Category II.
Rated pollution degree: 2.
B-7
C Communication
The LIS/HIS function of BC-20s enables the communication between the analyzer and the
PC in laboratory through Ethernet, including sending analysis results to and receiving worklist
from PC.
The LIS/HIS communication protocol involved in communication of BC-20s are 15ID and HL7.
For details about the connection control, and the introduction, message definition and
examples, please contact Mindray Customer Service Department or your local distributor.
C-1
P/N: 046-007636-00(2.0)

BC 20s Handbuch

Uploaded by

Copyright:

Available Formats

BC 20s Handbuch

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BC 20s Handbuch

Uploaded by

Copyright:

Available Formats

What is the purpose of this document?

What is the purpose of this document?

What are the main components of the analyzer described in the document?

What are the main components of the analyzer described in the document?

BC-20s

Auto Hematology Analyzer

Intellectual Property Statement

Mindray intends to maintain the contents of this manual as confidential information.

Release, amendment, reproduction, distribution, rental, adaptation, translation or any other

, , are the trademarks, registered or otherwise, of Mindray in

 It is important for the hospital or organization that employs this equipment

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES,

This warranty shall not extend to:

Manufacturer: Shenzhen Mindray Bio-Medical Electronics Co., Ltd.

EC-Representative: Shanghai International Holding Corp. GmbH(Europe)

Address: Eiffestraβe 80, Hamburg 20537, Germany

1 Using This Manual ............................................................................................... 1-1

2 Understanding Your Analyzer ............................................................................ 2-1

3 Understanding the System Principles............................................................... 3-1

4 Installing Your Analyzer ...................................................................................... 4-1

5 Operating Your Analyzer ..................................................................................... 5-1

6 Reviewing Sample Results ................................................................................. 6-1

7 Using the QC Programs ...................................................................................... 7-2

8 Calibrating Your Analyzer ................................................................................... 8-1

9 Customizing the Analyzer Software .................................................................. 9-1

10 Servicing Your Analyzer .................................................................................... 10-1

11 Troubleshooting Your Analyzer........................................................................ 11-1

1.2 Who Should Read This Manual

 learn about the BC-20s hardware and software;

 set up system parameters;

 perform daily operating tasks;

 perform system maintenance and troubleshooting.

1.3 How to Find Information

If you want to … See …

1.4 Conventions Used in This Manual

1.5 Terms Used in Software Operation

read the statement below the symbol. The statement is

When you see... It means...

read the statement below the symbol. The statement is

When you see... It means...

CAUTION, CONSULT ACCOMPANYING

EXERCISE CAUTION WHEN WORKING

PROTECTIVE EARTH (GROUND)

FOR IN VITRO DIAGNOSTIC USE

THE DEVICE IS FULLY CONFORMANCE

THE FOLLOWING DEFINITION OF THE

2.2 Product Description

White Blood Cell count WBC

2.4 Main Structure

Figure 2-1 Front of the analyzer

1 ---- Touch screen 2 ---- Indicator

Figure 2-2 Back of the main unit

1 ---- USB port 2 --- Network interface

Figure 2-3 Inside of the analyzer (front cover removed)

1 --- [Aspirate] key 2 --- Start assembly

Figure 2-4 Right side of the analyzer (right door open)

1 --- Baths 2 --- Diluent heating assembly

Figure 2-5 Left side of the analyzer

1 --- Recorder 2 --- Left door

2.4.1 Touch screen