DMVPN & MPLS

WAN Deployment
Guide
Revision: H2CY10
The Purpose of
Who Should Read This Guide
• Has in total 2000–10,000 connected employees
this Document • Has up to 500 remote sites

• Uses MPLS Layer 3 VPN as a WAN transport
• Uses the Internet as a secure WAN transport
• Requires a resilient WAN
• Requires an application optimization solution to improve WAN
This guide is a reference on deploying a WAN to connect a primary site to performance
up to 500 remote sites using MPLS and Internet.
• Has IT workers with a CCNA® certification or equivalent experience
It includes an overview of the operational problems that can be solved by
MPLS and Internet VPN and also a discussion of the agency relevance of • Wants to deploy their network infrastructure efficiently
application optimization technology. The guide includes details of various • Wants the assurance of a tested solution
topology designs with increasing levels of scale and resiliency. It also pro-
• Requires a migration path for growth
vides step-by-step configuration instructions for the routers, switches and
WAN optimization devices that make up the WAN and remote site solution.
Related Documents
Related Reading
Design Overview
LAN Deployment Guide
Internet Edge Deployment Guide
Optional
Midsize BN Foundation Design Overview
Design Guides Deployment Guides
Foundation Deployment
Design Overview
Guides
WAN Deployment
You are Here
Guide
WAN Configuration Guide
Network Management
Guides
Using this Borderless Networks Guide 2

Table of Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Deploying the WAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Using the Deployment Guides . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Overall WAN Architecture Design Goals. . . . . . . . . . . . . . . . . . . . . . . . 14
Ease of Deployment, Flexibility and Scalability. . . . . . . . . . . . . . . . . . . . 3 Deploying an MPLS WAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Resiliency and Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Deploying a DMVPN WAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Easy to Manage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Deploying a WAN Remote-Site Distribution Layer . . . . . . . . . . . . . . . . 74
Advanced Technology Ready. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Deploying WAN Quality of Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 0
Deploying Application Optimization with WAAS. . . . . . . . . . . . . . . . . . 8 4
Architecture Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
WAN Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Large Agencies WAN Deployment Product List. . . . . . . . . . . . . . . . . . . . . . . . . . 96
IP Multicast. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Appendix A: Technical Feature Supplement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Quality of Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Front Door VRF for DMVPN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 9
WAN Optimization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Appendix B: SBA for Large Agencies Document System. . . . . . . . . . . . . . . . 102
ALL DESIGNS, SPECIFICATIONS, STATEMENTS, INFORMATION, AND RECOMMENDATIONS (COLLECTIVELY, "DESIGNS") IN THIS MANUAL ARE PRESENTED "AS IS," WITH ALL FAULTS. CISCO AND ITS SUPPLIERS
DISCLAIM ALL WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF
DEALING, USAGE, OR TRADE PRACTICE. IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITA-
TION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THE DESIGNS, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. THE DESIGNS ARE SUBJECT TO CHANGE WITHOUT NOTICE. USERS ARE SOLELY RESPONSIBLE FOR THEIR APPLICATION OF THE DESIGNS. THE DESIGNS DO NOT CONSTITUTE THE TECHNICAL
OR OTHER PROFESSIONAL ADVICE OF CISCO, ITS SUPPLIERS OR PARTNERS. USERS SHOULD CONSULT THEIR OWN TECHNICAL ADVISORS BEFORE IMPLEMENTING THE DESIGNS. RESULTS MAY VARY
DEPENDING ON FACTORS NOT TESTED BY CISCO.
Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes
only. Any use of actual IP addresses in illustrative content is unintentional and coincidental. Cisco Unified Communications SRND (Based on Cisco Unified Communications Manager 7.x)
© 2010 Cisco Systems, Inc. All rights reserved.
Table of Contents
Introduction
The Local Area Network Deployment Guide covers wired and wireless
network access with ubiquitous capabilities for both the larger campus-size
LAN as well as the smaller remote-site LAN. Resiliency, security, and scal-
ability is included to provide a robust communications environment. Quality
of service (QoS) is integrated to ensure that the base architecture can support
a multitude of applications including low latency, drop-sensitive multimedia
The Cisco Smart Business Architecture (SBA) for Government Large applications coexisting with data applications on a single network. The guide
Agencies—Borderless Networks is designed for networks that have 2000 also provides a guest and partner access solution that is secured from
to 10,000 connected users. We created a prescriptive, out-of-the-box accessing internal confidential information while using the same wireless
deployment guide that is based on best-practice design principles and that infrastructure that employees use.
delivers flexibility and scalability. The deployment guides are designed to
make the Borderless Network for Large Agencies easy—easy to configure, The Wide Area Network Deployment Guide includes the primary site
easy to deploy, and easy to manage. aggregation design as well as multiple remote-site designs to accommodate
varying scale and service-level requirements in a common approach. The
The goal of any network implementation is to support the applications that flexibility in the WAN deployment guide provides guidance and configura-
benefit the users and the agency that it is built for. As they guide you tion for Multiprotocol Label Switching (MPLS) transport as well as broad-
through the depth and breadth of the architecture, the SBA deployment band or Internet transport in a primary or backup role. QoS is integrated to
guides are intended to simplify navigating among and learning the various ensure that the base architecture can support a multitude of applications
networking technologies that we used to build the architecture. Cisco SBA is on a single transport. The design integrates application optimization and
a solid network foundation that provides the flexibility to support new user or the deployment guide provides details on optimizing WAN traffic to ensure
network services without re-engineering the network. economical use of bandwidth while providing
a good user experience.
Using the Deployment Guides
The Internet Edge Deployment Guide focuses on security services such
The Large Agency architecture was designed, built, and validated as an as firewalls and intrusion prevention systems to protect your agency’s
end-to-end system. gateway to the Internet. Internet service provider connectivity and routing
To focus on specific elements of the architecture, there are three primary options, combined with server load balancing, provide resiliency to the
deployment guides, one each for Local Area Network (LAN), Wide Area design. The Email Security module covers protecting email from spam and
Network (WAN), and Internet Edge. To enhance the Large Agency archi- malware. The Web Security module provides acceptable-use control and
tecture, there are a number of supplemental guides that address specific monitoring as well as managing the increasing risk associated with clients
functions, technologies, or features that may be important to solving your browsing the Internet. The Virtual Private Network (VPN) design supports
operational problems. Within each of these deployment guides, you will find the teleworker and mobile user with secure remote access. All of these
a modular approach that allows you to start at the beginning and work your elements are covered in separate modules and yet are designed to work
way through or to jump to a specific module. Each deployment guide and together to provide a secure Internet Edge solution.
the modules within are designed to stand alone, so that you can deploy the
specific Cisco technology in a module without completing each previous
module. Each deployment guide includes a complete list of the products
and the software revisions tested, and a companion supplemental guide
contains all configuration files used.
The deployment guides begin with an agency overview of the common
operational problems addressed, followed by an architecture overview to
assist you with matching the value of a technology solution to your
operational problems.
Introduction 1
Figure 1. SBA for Large Agencies—Borderless Networks Overview
Internet Data
Internet
Campus
Edge Center
Edge
Internet
Internet Edge Routers
Remote
Email Security
I WAN
Access VPN
Appliance
Hardware and Software Aggregation
VPN Guest
Teleworker / WLAN
Mobile Worker
WAN Application Firewall Internet

Wireless Acceleration VPN
Servers
Access Point
Wireless W ww Web Security
W ww
Client LAN Controller Appliance
Access
Switch
Branch Router with

Application Acceleration
Core
Remote Switches
Collapsed
Distribution/Core
Switches
Distribution
I Switches
Wireless Regional
LAN Controller Router
Application Client
Acceleration Access
Switches
Regional
Office Building 1 Building 2 Building 3 Building 4
Introduction 2
Design Goals Many of these plug-in modules look identical for several different service
areas; this provides consistency and scalability in that the same support
This architecture is based on requirements gathered from customers,
methods can be used in multiple areas of the network to maintain the
partners, and Cisco field personnel for agencies with 2000 to 10,000 con-
network. These modules follow standard core-distribution-access network
nected users. When designing the architecture, we considered the gathered
design models and use layer separation to ensure that interfaces between
requirements and the following design goals:
the plug-ins are well defined.
• Ease of Deployment: Agencies can deploy the design consistently
across all products included in the architecture. The configurations used Resiliency and Security
in the deployment represent a best-practice methodology to enable a
fast and resilient deployment. One of the keys to maintaining a highly available network is building the
appropriate redundancy to guard against failure in the network, whether it
• Flexibility and Scalability: The architecture can grow with the agency is link, port, card, or chassis failure. But systems can be engineered to be
without being redesigned. too redundant, exhibiting failures of overly complex redundancy features,
• Resiliency and Security: The architecture keeps the network operating which results in complete communications failure. The redundancy in our
even during unplanned outages and attacks. architecture is carefully balanced with the complexity inherent in redundant
systems.
• Easy to Manage: The deployment guidance includes configuring
devices to be managed by a network management system (NMS) or as Building production network services without any form of redundancy is
unique elements of the network. unacceptable to most agencies. When building in the necessary redun-
dancy, care must also be taken to prevent large dependency chains that
• Advanced Technology Ready: Implementing advanced technologies result in greater risk of system failure. For example, chains of devices that
like collaboration is easy because the network foundation is already do not have cross-connections may create a dependency on both chains
configured with the required baseline network services. being completely available.
Ease of Deployment, Flexibility and Scalability With the addition of a significant amount of delay-sensitive and drop-
sensitive traffic such as voice and video conferencing, we also place a
Agencies of 2000 to 10,000 users are often are spread out among different strong emphasis on recovery times. Choosing designs that reduce the time
geographical locations. The locations might have labels like remote site, between failure detection and recovery is important for ensuring that the
regional site, or headquarters. This architecture addresses how to build a network stays available even in the face of a minor component failure.
network for all these locations, irrespective of the label.
Security of the network is also a very strong component of the architecture.
In this design, several methods are used to create and maintain a scalable In a large network, there are many entry points and we ensure that they
network. Defining a common framework with a convergence of design are as secure as possible without making the network too difficult to use.
standards drives global consistency and optimizes the design process, Securing the network not only helps keep the network safe from attacks but
which ultimately results in lower cost and complexity. Standardization is the is also a key component to networkwide resiliency.
key to scalability; by keeping a small number of standard designs for com-
mon portions of the network, support staff are able to design services for, Easy to Manage
implement, and support these network areas more effectively.
While this guide focuses on the deployment of the network foundation, the
To enhance scalability, we take a modular design approach; beginning with a next phase management and operation are considered. The configurations
set of standard, global building blocks, we can assemble a scalable network in the deployment guides are designed to allow the devices to be managed
to meet requirements. For instance, to build a campus network, we might both via normal device management connections, such as SSH and HTTPS,
start with a LAN module, connect an Internet edge module, and then add a but also via NMS. The configuration of the NMS is not covered in this guide.
WAN module.
Introduction 3
Advanced Technology Ready
Flexibility, scalability, resiliency, and security all are characteristics of an
advanced technology-ready network. The modular design of the architec-
ture means that technologies can be added when the agency is ready to
deploy them. However, the deployment of advanced technologies, such
as collaboration, is eased because the architecture includes products and
configurations that are ready to support collaboration from day one. For
example, access switches provide Power over Ethernet (PoE) for phone
deployments without the need for a local power outlet. The entire network
is preconfigured with QoS to support high-quality voice. Multicast is config-
ured in the network to support efficient voice and broadcast-video delivery.
Beyond the wired network, the wireless network is also preconfigured for
devices that send voice over the wireless LAN, providing IP telephony over
802.11 Wi-Fi (referred to as mobility) at all locations. The Internet edge is
also ready to provide soft phones via VPN, as well as traditional hard or desk
phones.
Introduction 4
Architecture Overview
MPLS WAN Transport
Cisco IOS MPLS enables large agencies and service providers to build next-
generation intelligent networks that deliver a wide variety of advanced, value-
added services over a single infrastructure. This economical solution can
be integrated seamlessly over any existing infrastructure, such as IP, Frame
Relay, ATM, or Ethernet.
The Cisco SBA for Large Agencies—Borderless Networks WAN
Deployment Guide provides a design that enables highly available, secure, MPLS Layer 3 VPNs use a peer-to-peer VPN Model that leverages the
and optimized connectivity for multiple Border Gateway Protocol (BGP) to distribute VPN-related information. This
remote-site LANs. peer-to-peer model allows large-agency subscribers to outsource routing
information to service providers, which can result in significant cost savings
The WAN is the networking infrastructure that provides an Internet Protocol
and a reduction in operational complexity for agencies.
(IP)-based interconnection between remote sites that are separated by large
geographic distances. Subscribers who need to transport IP multicast traffic can enable
Multicast VPNs.
This document shows you how to deploy the network foundation and
services to enable the following: Internet as WAN Transport
• WAN connectivity for 25 to 500 remote sites The Internet is essentially a large-scale public WAN composed of multiple
interconnected service providers. The Internet can provide reliable high-
• Primary and secondary links to provide redundant topology options performance connectivity between various locations, although it lacks any
for resiliency explicit guarantees for these connections. Despite its “best effort” nature,
• Data privacy via encryption the Internet is a sensible choice for an alternate WAN transport, or for a
primary transport when it is not feasible to connect with another transport
• WAN optimization and application acceleration option.
• Wired and wireless LAN access at all remote sites Internet connections are typically included in discussions relevant to the
Internet edge, specifically for the primary site. Remote-site routers also
WAN Design commonly have Internet connections, but do not provide the same breadth
The primary focus of the design is to allow usage of the following commonly of services using the Internet. For security and other reasons, Internet
deployed WAN transports: access at remote sites is often routed through the primary site.
• Multiprotocol Label Switching (MPLS) Layer 3 VPN The WAN leverages the Internet for VPN site-to-site connections as either a
backup WAN transport (to MPLS VPN) or as a primary WAN transport.
• Internet VPN
DMVPN
At a high level, the WAN is an IP network, and these transports can be easily
Dynamic Multipoint VPN (DMVPN) is a solution for building scalable site-to-
integrated to the design.
site VPNs that support a variety of applications. DMVPN is widely used for
The chosen architecture designates a primary WAN-aggregation site that is encrypted site-to-site connectivity over public or private IP networks and
analogous to the hub site in a traditional hub-and-spoke design. This site can be implemented on all WAN routers used in this deployment guide.
has direct connections to both WAN transports and high-speed connections
DMVPN was selected for the encryption solution for the Internet transport
to the selected service providers. In addition, the site leverages network
because it supports on-demand full mesh connectivity with a simple
equipment scaled for high performance and redundancy. The primary WAN-
hub-and-spoke configuration and a zero-touch hub deployment model for
aggregation site is coresident with the data center and usually the primary
adding remote sites. DMVPN also supports spoke routers that have dynami-
Campus or LAN as well.
cally assigned IP addresses.
DMVPN makes use of multipoint Generic Route Encapsulation tunnels
Architecture Overview 5
(mGRE) to interconnect the hub to all of the spoke routers. These mGRE Table 1. WAN-Aggregation Designs
tunnels are also sometimes referred to as DMVPN clouds in this context.
This technology combination supports unicast, multicast, and broadcast IP, WAN Edge Transport Transport Transport
including the ability to run routing protocols within the tunnels. Model Links Router(s) 1 2 3
Ethernet WAN WAN100 Dual Dual MPLS VPN Internet
Both of the WAN transports mentioned previously use Ethernet as a standard A VPN
media type. Ethernet is becoming a dominant carrier handoff in many markets WAN500 Multiple Multiple MPLS VPN MPLS VPN Internet
and it is relevant to include Ethernet as the primary media in the tested A B VPN
architectures. Much of the discussion in this guide can also be applied to
non-Ethernet media (such as T1/E1, DS-3, OC-3, and so on), but they are not The characteristics of each design are as follows:
explicitly discussed. WAN100 Design
WAN-Aggregation Designs • Has up to 100 Mbps aggregate bandwidth
The WAN-aggregation (hub) designs include two or more WAN edge rout- • Supports up to 100 remote sites
ers. When referred to in the context of the connection to a carrier or service
provider, the WAN edge routers are typically known as customer edge (CE) • Has a single MPLS VPN carrier
routers. WAN edge routers that terminate VPN traffic are referred to as VPN • Uses a single Internet link
hub routers. All of the WAN edge routers connect into a distribution layer.
The WAN100 Design is shown in Figure 2.
The WAN transport options include MPLS VPN and traditional Internet
access. Both transport types connect to either a CE router or a VPN hub Figure 2. WAN100 Design
router, respectively. Interfacing with each of these transports requires a
different connection method and configuration.
There are two WAN-aggregation designs that are documented in this
deployment guide: WAN100 and WAN500. The primary difference between
the WAN100 and WAN500 designs is the overall scale of the architecture
and the capabilities of the various platforms chosen to support the design.
In both WAN-aggregation designs, tasks such as IP route summarization are
performed at the distribution layer. There are other various devices sup-
porting WAN edge services, and these devices should also connect into the
distribution layer.
Each MPLS carrier terminates to a dedicated WAN router with a primary goal
of eliminating any single points of failure. A single VPN hub router is used
across both designs. The various design models are contrasted in Table 1.
WAN500 Design Architecture Overview 6

• Has up to 1 Gbps aggregate bandwidth WAN Remote-Site Designs
• Supports up to 500 remote sites This guide documents multiple remote-site WAN designs, and they are
based on various combinations of WAN transports mapped to the site spe-
• Has multiple MPLS VPN carriers cific requirements for service levels and redundancy. These design variants
• Uses a single Internet link are shown in Figure 4.
The WAN500 Design is shown in Figure 3. Figure 4. WAN Remote-Site Designs
Figure 3. WAN500 Design
The remote-site designs include single or dual WAN edge routers.

These can be either a CE router or a VPN spoke router. In some cases,
a single WAN edge router can perform the role of both a CE router and
VPN-spoke router.
Most remote sites are designed with a single router WAN edge; however,
certain remote-site types require a dual router WAN edge. Dual router
candidate sites include regional office or remote campus locations with
large user populations, or sites with mission-critical needs that justify
additional redundancy to remove single points of failure.
The overall WAN design methodology is based on a primary WAN-aggregation
site design that can accommodate all of the remote-site types that map to
the various link combinations listed in Table 2.
Table 2. WAN Remote-Site Transport Options Table 3. WAN Remote-Site LAN Options
WAN Remote- WAN Primary Secondary WAN Remote-Site

Site Router(s) Transports Transport Transport Router(s) WAN Transports LAN Topology
Single Single MPLS VPN A Single Single Access only
Distribution/Access
Internet
Single Dual Access only
Single Dual MPLS VPN A Internet
Distribution/Access
MPLS VPN B Internet Dual Dual Access only
Dual Dual MPLS VPN A Internet Distribution/Access
MPLS VPN B Internet
WAN Remotes Sites—LAN Topology
Modularity in network design allows you to create design elements that can
For consistency and modularity, all WAN remote sites use the same VLAN
be replicated throughout the network.
assignment scheme shown in Table 4. This deployment guide uses a con-
Both WAN-aggregation designs and all of the WAN remote-site designs are vention that is relevant to any location that has a single access switch and
standard building blocks in the overall design. Replication of the individual this model can also be easily scaled to additional access closets through
building blocks provides an easy way to scale the network and allows for a the addition of a distribution layer.
consistent deployment method.
Table 4. WAN Remote Sites—VLAN Assignment
WAN/LAN Interconnect L3
Distribution/
The primary role of the WAN is to interconnect primary site and remote-site
VLAN Usage L2 Access Access
LANs. The LAN discussion within this guide is limited to how the WAN-
aggregation site LAN connects to the WAN-aggregation devices and how VLAN 100 Data (Primary) Unused Yes
the remote-site LANs connect to the remote-site WAN devices. Specific VLAN 65 Wireless Data Yes Yes
details regarding the LAN components of the design are covered in the
VLAN 70 Wireless Voice Yes Yes
Cisco SBA for Large Agencies—Borderless Networks LAN Deployment
Guide. VLAN 64 Data 1 Yes Yes
At remote sites, the LAN topology depends on the number of connected VLAN 69 Voice 1 Yes Yes
users and physical geography of the site. Large sites may require the use unassigned Data 2 Unused Yes
of a distribution layer to support multiple access layer switches. Other sites unassigned Voice 2 Unused Yes
may only require an access layer switch directly connected to the WAN
remote-site router(s). The variants that are tested and documented in this VLAN99 Transit Yes Yes
guide are shown in Table 3. (dual router only) (dual router only)
VLAN50 Router Link (1) Unused Yes
VLAN54 Router Link (2) Unused Yes
(dual router only)
Layer 2 Access A similar LAN design can be extended to a dual-router edge as shown in
Figure 6. This design change introduces some additional complexity. The
WAN remote sites that do not require additional distribution layer routing
first requirement is to run a routing protocol: Enhanced Interior Gateway
devices are considered to be flat or from a LAN perspective they are con-
Protocol (EIGRP) should be configured between the routers. For consistency
sidered unrouted Layer 2 sites. All Layer 3 services are provided by the
with the primary site LAN, use EIGRP process 100.
attached WAN router(s). The access switch(es), through the use of multiple
VLANs, can support services such as data (wired and wireless) and voice Because there are now two routers per subnet, a First Hop Redundancy
(wired and wireless). The design shown in Figure 5 illustrates the standard- Protocol (FHRP) must be implemented. We selected Hot Standby Router
ized VLAN assignment scheme. The benefits of this design are clear: all of Protocol (HSRP) as the FHRP for this design. HSRP is designed to allow for
the access switches can be configured identically, regardless of the number transparent failover of the first-hop IP router. HSRP provides high network
of sites in this configuration. availability by providing first-hop routing redundancy for IP hosts configured
with a default gateway IP address. HSRP is used in a group of routers for
Access switches and their configuration are not included in this guide. The
selecting an active router and a standby router. When there are multiple
Cisco SBA for Large Agencies—Borderless Networks LAN Deployment
routers on a LAN, the active router is the router of choice for routing packets;
Guide provides configuration details on the various access switching
the standby router is the router that takes over when the active router fails or
platforms.
when preset conditions are met.
IP subnets are assigned on a per-VLAN basis. This design only allocates
Figure 6. WAN Remote Site—Flat Layer 2 LAN (Dual Router)
subnets with a 255.255.255.0 netmask for the access layer, even if less than
254 IP addresses are required. (This model can be adjusted as necessary
to other IP address schemes.) The connection between the router and the
access switch must be configured for 802.1Q VLAN trunking with subinter-
faces on the router that map to the respective VLANs on the switch. The
various router subinterfaces act as the IP default gateways for each of the IP
subnet and VLAN combinations.
Figure 5. WAN Remote Site—Flat Layer 2 LAN (Single Router)
Enhanced Object Tracking (EOT) provides a consistent methodology for The appropriate method to avoid sending the traffic out the same interface
various router and switching features to conditionally modify their operation is to introduce an additional link between the routers and designate the link
based on information objects available within other processes. The objects as a transit network (Vlan 99). There are no hosts connected to the transit
that can be tracked include interface line protocol, ip route reachability, network, and it is only used for router-router communication. The routing
and ip sla reachability as well as several others. protocol runs between router subinterfaces assigned to the transit network.
No additional router interfaces are required with this design modification as
The IP service-level agreement (SLA) feature provides a capability for a
the 802.1Q VLAN trunk configuration can easily accommodate an additional
router to generate synthetic network traffic that can be sent to a remote
subinterface.
responder. The responder can be a generic IP endpoint that can respond
to an ICMP echo (ping) request, or can be a Cisco router running an IP SLA Distribution and Access Layer
responder process, that can respond to more complex traffic such as jitter
Large remote sites may require a LAN environment similar to that of a
probes. The use of IP SLA allows the router to determine end-to-end reach-
small campus LAN that includes a distribution layer and access layer.
ability to a destination and also the roundtrip delay. More complex probe
This topology works well with either a single or dual router WAN edge as
types can also permit the calculation of loss and jitter along the path. IP SLA
shown in Figure 7. To implement this design, the routers should connect via
is used in tandem with EOT within this design.
EtherChannel links to the distribution switch. These EtherChannel links are
To improve convergence times after a MPLS WAN failure, HSRP has the configured as 802.1Q VLAN trunks, to support both a routed point-to-point
capability to monitor the reachability of a next-hop IP neighbor through the link to allow EIGRP routing with the distribution switch, and in the dual router
use of EOT and IP SLA. This combination allows for a router to give up its design, to provide a transit network for direct communication between the
HSRP Active role if its upstream neighbor becomes unresponsive and that WAN routers.
provides additional network resiliency.
Figure 7. WAN Remote Site—Connection to Distribution Layer
HSRP is configured to be active on the router with the highest priority WAN
transport. EOT of IP SLA probes is implemented in conjunction with HSRP so
that in the case of WAN transport failure, the standby HSRP router associ-
ated with the lower priority (alternate) WAN transport becomes the active
HSRP router. The IP SLA probes are sent from the MPLS CE router to the
MPLS PE router to ensure reachability of the next hop router. This is more
effective than simply monitoring the status of the WAN interface.
The dual router designs also warrant an additional component that is
required for proper routing in certain scenarios. In these cases, a traffic
flow from a remote-site host might be sent to a destination reachable via
the alternate WAN transport (for example: a MPLS + DMVPN remote site
communicating with a DMVPN-only remote site). The primary WAN transport
router then forwards the traffic out the same data interface to send it to the
alternate WAN transport router, which then forwards the traffic to the proper
destination. This is referred to as hair-pinning.
The distribution switch handles all access layer routing, with VLANs trunked The RP is a control-plane operation that should be placed in the core of the
to access switches. No HSRP is required when the design includes a distri- network or close to the IP multicast sources on a pair of Layer 3 switches
bution layer. A full distribution and access layer design is shown in Figure 8. or routers.IP multicast routing begins at the distribution layer if the access
layer is Layer 2 and provides connectivity to the IP multicast RP. In designs
without a core layer, the distribution layer performs the RP function.
Figure 8. WAN Remote Site—Distribution and Access Layer (Dual Router)
This design is fully enabled for a single global scope deployment of IP
Multicast.The design uses an Anycast RP implementation strategy. This
strategy provides load sharing and redundancy in Protocol Independent
Multicast sparse mode (PIM-SM) networks. Two rendezvous points (RPs)
share the load for source registration and the ability to act as hot backup
routers for each other.
The benefit of this strategy from the WAN perspective is that all IP routing
devices within the WAN use an identical configuration referencing the
Anycast RPs. IP PIM sparse-mode is enabled on all interfaces including
loopbacks, VLANs and subinterfaces.
Quality of Service
Most users perceive the network as just a transport utility mechanism to
shift data from point A to point B as fast as it can. Many sum this up as just
“speeds and feeds.” While it is true that IP networks forward traffic on a
best-effort basis by default, this type of routing only works well for applica-
tions that adapt gracefully to variations in latency, jitter, and loss. However
networks are multiservice by design and support real-time voice and video
as well as data traffic. The difference is that real-time applications require
packets to be delivered within specified loss, delay, and jitter parameters.
In reality, the network affects all traffic flows and must be aware of end-user
IP Multicast requirements and services being offered. Even with unlimited bandwidth,
IP multicast allows a single IP data stream to be replicated by the infra- time-sensitive applications are affected by jitter, delay, and packet loss. QoS
structure (routers and switches) and sent from a single source to multiple enables a multitude of user services and applications to coexist on the same
receivers. IP multicast is much more efficient than multiple individual unicast network.
streams or a broadcast stream that would propagate everywhere. IP tele- Within the architecture, there are wired and wireless connectivity options
phony music on hold and IP video broadcast streaming are two examples of that provide advanced classification, prioritizing, queuing and congestion
IP multicast applications. mechanisms as part of the integrated quality of service (QoS) to help ensure
To receive a particular IP multicast data stream, end hosts must join a optimal use of network resources. This functionality allows for the differen-
multicast group by sending an Internet Group Membership Protocol (IGMP) tiation of applications that ensures each has the appropriate share of the
message to their local multicast router. In a traditional IP multicast design, network resources to protect the user experience and ensure the operations
the local router consults another router in the network that is acting as a of mission-critical applications.
Rendezvous Point (RP) to map the receivers to active sources so they can
join their streams.
Quality of service (QoS) is an essential function of the network infrastructure WAN Optimization
devices used throughout this architecture. QoS enables a multitude of user
Cisco Wide Area Application Services (WAAS) is a comprehensive WAN
services and applications, including real-time voice, high-quality video, and
optimization solution that accelerates applications over the WAN, delivers
delay-sensitive data to coexist on the same network. In order for the network
video to a remote office, and provides local hosting of remote-site IT ser-
to provide predictable, measurable, and sometimes guaranteed services,
vices. Cisco WAAS allows applications to be centralized and to use storage
it must manage bandwidth, delay, jitter, and loss parameters. Even if you do
in the data center while maintaining LAN-like application performance.
not require QoS for your current applications, the use of QoS for manage-
ment and network protocols protects the network functionality and manage- WAAS accelerates applications and data over the WAN, optimizes band-
ability under normal and congested traffic conditions. width, empowers cloud computing, and provides local hosting of remote-site
IT services, all with industry-leading network integration. Cisco WAAS allows
The goal of this design is to provide sufficient classes of service to allow
IT organizations to centralize applications and storage while maintaining
voice, interactive video, critical data applications, and management traffic
productivity for remote-site and mobile users.
to be added to the network, either from the initial deployment or later with
minimum system impact and engineering effort. WAAS is centrally managed and requires one or more Cisco WAAS Central
Manager devices that are physically located within the data center but are
The QoS classifications in Table 5 are applied throughout this design. This
accessible via a web interface.
table is included as a reference.
The design for optimizing WAN traffic requires the deployment of Cisco
Table 5. QoS Service Class Mappings Wide Area Application Engine (WAE) appliances or modules at both the
Layer 3 Layer 2 WAN-aggregation site and at the WAN remote sites. The WAEs run WAAS
software that provides the WAN optimization services. The design requires
Service Class PHB DSCP IPP COS one or more WAE devices at every location, with multiple devices located
Network Control CS6 48 6 6 at a site to provide resiliency. The Cisco WAAS solution operates as a TCP
Telephony EF 46 5 5 proxy that integrates transparently with other services in the network and
provides WAN optimization benefits to the end users, without creating
Signaling CS3 24 3 3 optimization tunnels across the WAN.
Multimedia
AF41, 42, 43 34, 36, 38 4 4 The WAN optimization solution is tightly integrated with the WAN routers,
Conferencing
with the routers controlling the interception and redirection of traffic to be
Real Time optimized with WAAS. The design places the WAE appliances on exist-
CS4 32 4 4
Interactive ing network segments which removes the need for significant network
Multimedia modifications.
AF31, 32, 34 26, 28, 30 3 3
Streaming A successful WAAS implementation requires the following:
Broadcast Video CS5 40 4 4
• A method for intercepting chosen traffic to or from the WAN
Low-Latency Data AF21, 22, 23 18, 20, 22 2 2
• The ability to direct the chosen traffic to the WAE devices for
OAM CS2 16 2 2 proper optimization
Bulk Data AF11, 12, 13 10, 12, 14 1 1
• The ability for the WAE to reinject optimized traffic into the network
Scavenger CS1 8 1 1 after optimization
Default
DF 0 0 0
“Best Effort”
Web Cache Communication Protocol (WCCP) is used on the routers to
intercept traffic entering the router from the LAN (sourced from the client or
the data center) or entering the router from the WAN (from a remote WAE).
As part of the WCCP redirection, traffic is forwarded to a chosen WAE via a
GRE tunnel.
Multiple WAE devices at one location can operate as a cluster. The routers
performing the WCCP redirection are responsible for load sharing across the
various WAE devices within a cluster. WAAS high availability uses what is
referred to as an N+1 model. This name means that if N equivalent devices
are required to support the required performance, then one additional
device is required to provide redundancy.
Traffic to be reinjected into the network uses a negotiated return WCCP
GRE tunnel egress method back to the originating router. This method is
preferred as it allows the WAE appliances to be located one or more routed
hops away from the WCCP router. There are several benefits associated
with this method, which are covered in more detail in the following sections.
Deploying the WAN
• Remote sites classified as Single-router, Dual-link must be able tolerate
the loss of either WAN transport.
• Remote sites classified as Dual-router, Dual-link must be able to tolerate
the loss of either an edge router or a WAN transport.
Path Selection Preferences

Overall WAN Architecture Design Goals There are many potential traffic flows based on which WAN transports are in
use and whether or not a remote site is using a dual WAN transport.
IP Routing
The design has the following IP routing goals: The single WAN transport routing functions as follows:
• Provide optimal routing connectivity from primary WAN-aggregation MPLS VPN-connected site:
sites to all remote locations • Connects to a site on the same MPLS VPN; the optimal route is direct
• Isolate WAN routing topology changes from other portions of the network within the MPLS VPN (traffic is not sent to the primary site)
• Ensure active/standby symmetric routing when multiple paths exist, for • Connects to any other site; the route is through the primary site
ease of troubleshooting and to prevent oversubscription of IP telephony DMVPN-connected site:
call admission control limits
• Connects to any DMVPN single connected site; the optimal route is
• Provide site-site remote routing via the primary WAN-aggregation site direct within the DMVPN (only initial traffic is sent to the DMVPN hub, and
(hub-and-spoke model) then is cut-through via a spoke-spoke tunnel)
• Permit optimal direct site-site remote routing when carrier services allow • Connects to any other site; the route is through the primary site
(spoke-to-spoke model)
The use of the dual WAN transports is specifically tuned to behave in an
• Support IP multicast sourced from the primary WAN-aggregation site active/standby manner. This type of configuration provides symmetric rout-
At the WAN remote sites, there is no local Internet access for web browsing ing, with traffic flowing along the same path in both directions. Symmetric
or cloud services. This model is referred to as a centralized Internet model. It routing simplifies troubleshooting as bidirectional traffic flows always
is worth noting that sites with Internet/DMVPN for either a primary or backup traverse the same links.
transport could potentially provide local Internet capability; however, for this MPLS VPN + DMVPN dual connected site:
design, only encrypted traffic to other DMVPN sites is permitted to use the
Internet link. In the centralized Internet model, a default route is advertised to • Connects to a site on the same MPLS VPN; the optimal route is direct
the WAN remote sites in addition to the internal routes from the data center within the MPLS VPN (traffic is not sent to the primary site)
and campus. • Connects to any DMVPN single-connected site; the optimal route is
direct within the DMVPN (only initial traffic is sent to the DMVPN hub, and
LAN Access then is cut-through via spoke-spoke tunnel)
All remote sites are to support both wired and wireless LAN access. • Connects to any other site; the route is through the primary site
High Availability
The network must tolerate single failure conditions including the failure of
any single WAN transport link or any single network device at the primary
WAN-aggregation site.
Deploying the WAN 14

Data Privacy (Encryption) Deploying an MPLS WAN
All remote-site traffic must be encrypted when transported over public IP MPLS WAN Agency Overview
networks such as the Internet.
Agencies require the WAN to provide sufficient performance and reliability
The use of encryption should not limit the performance or availability of a for the remote-site users to be effective in supporting the agency. Although
remote-site application, and should be transparent to end users. most of the applications and services that the remote-site worker uses are
centrally located, the WAN design must provide a common resource access
Quality of Service (QoS) experience to the workforce regardless of location.
The network must ensure that applications perform across the WAN during To control operational costs, the WAN must support the convergence of
times of network congestion. Traffic must be classified and queued and voice, video, and data transport onto a single, centrally managed infrastruc-
the WAN connection must be shaped to operate within the capabilities of ture. Many government agencies require a flexible network design that
the connection. When the WAN design uses a service provider offering allows for country-specific access requirements and controls complexity.
with QoS, the WAN edge QoS classification and treatment must align to the The ubiquity of carrier-provided MPLS networks makes it a required consid-
service provider offering to ensure consistent end-to-end QoS treatment of eration for an agency building a WAN.
traffic. To reduce the time needed to deploy new technologies that support emerg-
ing applications and communications, the WAN architecture requires a flex-
Application Optimization ible design. The ability to easily scale bandwidth or to add additional sites or
resilient links makes MPLS an effective WAN transport for growing agencies.
Most application traffic from the WAN-aggregation site to any remote site, or
any traffic from a remote site to any other remote site, should be optimized.
The use of application optimization should be transparent to end users. The MPLS WAN Technical Overview
application optimization design should include high-availability components
to complement other high-availability components of the WAN design. WAN 500 Design
The WAN 500 design is intended to support up to 500 remote sites with a
Design Parameters combined aggregate WAN bandwidth of up to 1.0 Gbps. The most critical
devices are the WAN routers that are responsible for reliable IP forwarding
This deployment guide uses certain standard design parameters and refer- and QoS. This design uses the Cisco ASR1002 Aggregation Services Router
ences various network infrastructure services that are not located within the for the MPLS CE router.
WAN. These parameters are listed in Table 6.
Table 6. Universal Design Parameters
Network Service IP Address

Domain Name cisco.local
Active Directory, DNS Server, DHCP Server 10.4.200.10
Authentication Control System (ACS) 10.4.200.15
Network Time Protocol (NTP) Server 10.4.200.17
IP Multicast Rendezvous Point (Anycast RP) 10.4.60.252

The WAN 500 design uses dual MPLS carriers and dual MPLS CE routers as The Cisco ASR 1000 Series Aggregation Services Routers represent the
shown in Figure 9. next-generation, modular, services-integrated Cisco routing platform. They
are specifically designed for WAN aggregation, with the flexibility to sup-
Figure 9. WAN 500 Design—MPLS Connections port a wide range of 4- to 16-Mpps packet-forwarding capabilities, 2.5- to
20-Gbps system bandwidth performance, and scaling. The Cisco ASR 1000
Series is fully modular from both hardware and software perspectives, and
the routers have all the elements of a true carrier-class routing product that
serves both large-agency and service-provider networks.
WAN 100 Design
The WAN 100 design is intended to support up to 100 remote sites with
a combined aggregate WAN bandwidth of up to 100 Mbps. The WAN 100
design is essentially a smaller version of the WAN 500 design. This variant
is included to provide a limited scale option. If further growth in bandwidth
or an increase in the number of sites is expected, then the WAN 500 design
should be used. Using the larger design can prevent unnecessary down-
time associated with device upgrades. This design uses the Cisco 3945E
Integrated Services Router for the MPLS CE router. The WAN 100 design
uses a single MPLS carrier and a single MPLS CE router as shown in
Figure 10.

Figure 10. WAN 100 Design—MPLS Connection Table 7. WAN Remote-Site Integrated Service Router Options
2911 2921 3925 3945

Ethernet WAN 35 Mbps 50 Mbps 100 Mbps 150 Mbps
with Services1
On-board GE 3 3 3 3
ports
Service Module 1 2 2 4
Slots2
Redundant Power No No Yes Yes
Supply Option
Notes:
1. The performance numbers are conservative numbers obtained when the
router is passing IMIX traffic with heavy services configured and the CPU
utilization is under 75 percent.
2. Some service modules are double-wide.
The MPLS CE routers at the WAN remote sites connect in the same manner
as the MPLS CE routers at the WAN-aggregation site. The single link MPLS
WAN remote site shown in Figure 11 is the most basic of building blocks for
any remote location. This design can be used with the CE router connected
directly to the access layer, or can support a more complex LAN topology by
connecting the CE router directly to a distribution layer.
The IP routing is straightforward and can be handled entirely by using static
routes at the WAN-aggregation site and static default routes at the remote
site. However, there is significant value to configuring this type of site with
Remote Sites—MPLS CE Router Selection dynamic routing.
The actual WAN remote-site routing platforms remain unspecified because Dynamic routing makes it easy to add or modify IP networks at the remote
the specification is tied closely to the bandwidth required for a location and site, because any changes are immediately propagated to the rest of the
the potential requirement for the use of service module slots. The ability to network. MPLS VPN-connected sites require static routing to be handled by
implement this solution with a variety of potential router choices is one of the the carrier, and any changes or modifications require a change request to
benefits of a modular design approach. the carrier.
There are many factors to consider in the selection of the WAN remote-site
routers. Among those, and key to the initial deployment, is the ability to
process the expected amount and type of traffic. We also need to be con-
cerned with having enough interfaces, enough module slots, and a properly
licensed Cisco IOS® image that supports the set of features that is required
by the topology. We tested four integrated service router models as MPLS
CE routers and the expected performance is shown in Table 7.

Figure 11. MPLS WAN Remote Site (Single-Router, Single-Link) Figure 12. MPLS WAN + DMVPN Remote Site (Dual-Link Options)
Design Details
The basic single-link design can be augmented through the addition of an
alternate WAN transport that uses DMVPN over Internet and either connects All WAN-aggregation MPLS CE routers connect to the same resilient switch-
on the same router or on an additional router. These alternate designs are ing device in the distribution layer. All devices use EtherChannel connec-
shown in Figure 12. Adding an additional link provides the first level of high tions consisting of two port bundles. This design provides both resiliency
availability for the remote site. The router can automatically detect failure of and additional forwarding performance. Additional forwarding performance
the primary link and reroute traffic to the secondary path. It is mandatory to can be accomplished by increasing the number of physical links within an
run dynamic routing when there are multiple paths. The routing protocols are EtherChannel.
tuned to ensure the desired traffic flows. WAN transport via Ethernet is the only media type tested and included in
The dual-router, dual-link design continues to improve upon the level of high the configuration section. Other media types are commonly used (such as
availability for the site. This design can tolerate the loss of the primary router T1/E1), and these technologies are reliable and well understood. Due to the
because the secondary router reroutes traffic via the alternate path. multiplicity of potential choices for transport, media type, and interface type,
we decided to limit the focus of this deployment guide. Documentation of
additional variants is available in other guides.
MPLS VPNs require a link between a provider edge (PE) router and a CE
router. The PE and CE routers are considered IP neighbors across this link.
CE routers are only able to communicate with other CE routers across the
WAN via intermediate PE routers as shown in Figure 13.

Figure 13. MPLS VPN (PE-CE Connections) At the WAN-aggregation site, an MPLS CE router must be connected both to the
distribution layer and to its respective MPLS carrier. Multiple routing protocols
(EIGRP and BGP) are used to exchange routing information, and the routing
protocol configurations are tuned from their default settings to influence traffic
flows to their desired behavior. The IP routing details for the single and dual MPLS
carrier WAN-aggregation topology are shown in Figure 14.
Figure 14. WAN500/WAN100 Designs—MPLS CE Routing Detail
Both the PE and CE routers are required to have sufficient IP-routing information
to provide end-to-end reachability. Maintaining this routing information typically
requires a routing protocol, and BGP is most commonly used for this purpose.
The various CE routers advertise their routes to the PE routers. The PE routers
propagate the routing information within the carrier network and in turn re-adver-
tise the routes back to other CE routers. This propagation of routing information is
known as dynamic PE-CE routing and it is essential when any sites have multiple
WAN transports (often referred to as dual-homed or multi-homed).
Tech Tip
EIGRP
We chose EIGRP as the primary routing protocol because it is easy to configure,
EIGRP and OSPF are also effective as PE-CE routing protocols, but may does not require a large amount of planning, has flexible summarization and
not be universally available across all MPLS VPN carriers. filtering, and can scale to large networks. As networks grow, the number of IP
prefixes or routes in the routing tables grows as well. You should program IP sum-
marization on links where logical boundaries exist, such as distribution layer links
Sites with only a single WAN transport (a single-homed site) do not require to the wide area or to a core. By performing IP summarization, you can reduce
dynamic PE-CE routing, and can rely on static routing because there is only a the amount of bandwidth, processor, and memory necessary to carry large route
single path to any destination. This design only includes dynamic PE-CE routing tables, and reduce convergence time associated with a link failure.
to provide consistency with configurations across both single-homed and dual- In this design, EIGRP process 100 is the primary EIGRP process and is
homed sites. This also allows for easy transition from a single-homed to a dual- referred to as EIGRP-100.
homed remote-site design by adding an additional link to an existing remote site.
EIGRP-100 is used at the WAN-aggregation site to connect to the primary
We did not test the PE routers and their configurations are not included in site LAN distribution layer and at WAN remote sites with dual WAN routers or
this guide. with distribution-layer LAN topologies.
An MPLS VPN WAN deployment requires the installation and configuration of BGP
MPLS CE routers at every location including the WAN-aggregation site, and at
every MPLS WAN-connected remote site. We have chosen BGP as the routing protocol for use between the PE and
CE routers for connection to the MPLS VPNs because it is consistently
supported across virtually all MPLS carriers. In this role, BGP is

straightforward to configure and requires little or no maintenance. BGP Step 1: Configure the device hostname.
scales well and can be used to advertise IP aggregate addresses for remote hostname [hostname]
sites.
BGP requires the selection of an Autonomous System Number (ASN). In this Step 2: Configure in-band management interface.
design, we use a private ASN (65511) as designated by the Internet Assigned All devices leverage a loopback address. A loopback is a virtual interface
Number Authority (IANA). The private ASN range is 64512 to 65534. that is consistently reachable when multiple paths exist to the device.
A dual-carrier MPLS design requires an iBGP connection between the CE Various other features may use the loopback.
routers to properly retain routing information for the remote sites. interface Loopback0
ip address [IP address] 255.255.255.255
Process Step 3: Configure device-management protocols.

Secure Shell (SSH) is an application and a protocol that provides a secure
replacement to RSH and Telnet.
WAN-Aggregation MPLS CE Router Configuration Secure management access is enabled through the use of the SSH and/or
1. Complete the WAN Router Universal Configuration HTTPS protocols.
2. Connect to Distribution Switch Secure HTTP (HTTPS) provides the capability to connect a HTTP server
securely. It uses Secure Sockets Layer (SSL) and Transport Layer Security
3. Connect to MPLS PE Router (TLS) to provide device authentication and data encryption.
4. Configure EIGRP Both protocols are encrypted for privacy and the nonsecure protocols,
5. Configure BGP Telnet and HTTP, have been disabled.
6. Configure IP Multicast Routing ip domain-name cisco.local
no ip http server
Enabling SSH requires that a public/private keypair be generated for the

Procedure 1 Finish the WAN Router Universal Config device:
crypto key generate rsa modulus 2048
ip ssh version 2
Procedure Steps: ip ssh source-interface Loopback0
1. Configure the device hostname.
2. Configure in-band management. Various levels of device management may be available through a web
interface. For secure access to this interface, you must enable the secure
3. Configure device-management protocols. server (the following command also generates a public/private keypair as
4. Configure secure user authentication. shown previously):
ip http secure-server
5. Configure a synchronized clock.
Allow only SSH access to the device:

line vty 0 15
transport input ssh

When synchronous logging of unsolicited messages and debug output server in the network. The local NTP server typically references a more
is turned on, console log messages are displayed on the console after accurate clock feed from an outside source. Configuring console mes-
interactive CLI output is displayed or printed. This command is also useful sages, logs, and debug output on switches, routers, and other devices in the
for allowing you to continue typing at the device console when debugging is network to provide timestamps on output allows cross-referencing of events
enabled. in the network.
line con 0 ntp server 10.4.200.17
logging synchronous ntp source Loopback0
ntp update-calendar ! this command not for use on ASR1000
Series
Simple Network Management Protocol (SNMP) is enabled to allow the
!
network infrastructure devices to be managed by a network management clock timezone PST -8
system (NMS). SNMPv2c is configured both for a read-only and a read-write clock summer-time PDT recurring
community string. !
snmp-server community cisco RO service timestamps debug datetime msec localtime
snmp-server community cisco123 RW service timestamps log datetime msec localtime
snmp-server trap-source Loopback0
Step 4: Configure secure user authentication. Procedure 2 Connect to Distribution Switch
Authentication, authorization and accounting (AAA) is enabled for access

control. All management access to the network infrastructure devices (SSH, A Layer 3 port-channel interface connects to the WAN distribution switch.
Telnet, HTTP, and HTTPS) is controlled with AAA. The following configuration creates an EtherChannel link between the router
and switch, with two channel-group members.
A local AAA user database is defined on the network infrastructure devices
to provide the ability to manage them in case the centralized RADIUS server Procedure Steps:
is unavailable, or if you do not have a RADIUS server in your agency. 1. Configure the port-channel interface and assign an IP address.
We highly recommend the use of a centralized authentication database. 2. Administratively enable the port-channel group members and assign the
enable secret c1sco123 appropriate channel group.
service password-encryption
!
username admin password c1sco123 Step 1: Configure the port-channel interface and assign the IP address.
aaa new-model
aaa authentication login default group radius local As a best practice use the same channel numbering on both sides of the link
ip radius source-interface Loopback0 where possible.
radius-server host 10.4.200.15 key SecretKey interface Port-channel [number]
ip address [IP address] [netmask]
Step 5: Configure a synchronized clock.
Step 2: Enable the port-channel group members and assign the appropriate
Network Time Protocol (NTP) is designed to synchronize a network of channel group.
devices. An NTP network usually gets its time from an authoritative time
source, such as a radio clock or an atomic clock attached to a time server. Not all router platforms can support Link Aggregation Control Protocol
NTP then distributes this time across the network. NTP is extremely efficient; (LACP) to negotiate with the switch, so EtherChannel is configured statically.
no more than one packet per minute is necessary to synchronize two interface [interface type] [number]
devices to within a millisecond of one another. no ip address
channel-group [number]
Network devices should be programmed to synchronize to a local NTP no shutdown

Procedure 2 Example interface [interface type] [number]
interface Port-channel1 ip address [IP address] [netmask]
ip address 10.4.128.2 255.255.255.252
! Step 3: Administratively enable the interface and disable CDP.
interface GigabitEthernet0/0/0
no ip address We do not recommend the use of CDP on external interfaces.
channel-group 1 interface [interface type] [number]
no shutdown no cdp enable
! no shutdown
no ip address Procedure 3 Example
channel-group 1
no shutdown interface GigabitEthernet0/0/4
bandwidth 300000
ip address 10.4.142.1 255.255.255.252
no cdp enable
Procedure 3 Connect to MPLS PE Router no shutdown
Procedure Steps:
Procedure 4 Configure EIGRP
1. Assign the interface bandwidth.
2. Assign the IP address and netmask of the WAN interface.
Procedure Steps:
3. Administratively enable the interface and disable CDP.
1. Enable EIGRP.
2. Redistribute BGP into EIGRP.
Step 1: Assign the interface bandwidth.
3. Configure inbound distribute-list for EIGRP.
The bandwidth value should correspond to the actual interface speed, or if a
subrate service is used, then use the policed rate from the carrier.
Step 1: Enable EIGRP.
The example shows a Gigabit interface (1000 Mbps) with a sub-rate of 300
Mbps. EIGRP is configured facing the LAN distribution or core layer. In this design,
the port-channel interface and the loopback must be EIGRP interfaces. The
Command Reference: loopback may remain a passive interface. The network range must include
bandwidth kbps both interface IP addresses, either in a single network statement or in
multiple network statements. This design uses a best practice of assigning
NOTE: 300 Mbps = 300000 kbps
the router ID to a loopback address.
interface [interface type] [number]
router eigrp [as number]
bandwidth [bandwidth (kbps)]
network [network] [inverse mask]
passive-interface default
Step 2: Assign the IP address and netmask of the WAN interface. no passive-interface [interface]
eigrp router-id [IP address of Loopback0]
The IP addressing used between CE and PE routers must be negotiated with no auto-summary
your MPLS carrier. Typically a point-to-point netmask of 255.255.255.252 is used.

Step 2: Redistribute BGP into EIGRP. It is important when creating the access-list to include a permit any
statement at the end to permit the installation of non-matching routes.
The BGP routes are redistributed into EIGRP with a default metric. By
default, only the bandwidth and delay values are used for metric calculation.
Command Reference:
Tech Tip
default-metric bandwidth delay reliability loading mtu
bandwidth Minimum bandwidth of the route in kilobytes per second
delay Route delay in tens of microseconds. Because of the explicit permit entry at the end of the ACL, to
router eigrp [as number] add deny entries you must insert new ACL entries with a specific
default-metric [bandwidth] [delay] 255 1 1500 sequence number.
redistribute bgp [BGP ASN]
Step 3: Configure inbound distribute-list for EIGRP. ip access-list standard [ACL name]
deny [network 1] [network 1 inverse mask]
This design uses mutual route redistribution; BGP routes are distributed into deny [network 2] [network 2 inverse mask]
EIGRP and EIGRP routes are distributed into BGP (covered in Procedure 5). <additional lines as necessary>
It is important to tightly control how routing information is shared between deny [network N] [network N inverse mask]
different routing protocols when this configuration is used; otherwise. it is permit any
possible to experience route flapping, where certain routes are repeatedly
installed and with-drawn from the device routing tables. Proper route control router eigrp [as number]
ensures the stability of the routing table. distribute-list [ACL name] in
An inbound distribute-list is used to limit which routes are accepted for instal-
Procedure 4 Example
lation into the route table. The WAN-aggregation MPLS CE routers are con-
ip access-list standard BLOCK-DIST-ROUTES-CE
figured to only accept routes which do not originate from the WAN. In order
remark Block WAN specific routes from WAN distribution layer
to accomplish this task requires the creation of an access-list that matches deny 10.5.0.0 0.0.255.255
any routes originating from the WAN. This design allows for a straightforward deny 10.4.142.0 0.0.0.255
summarization of the various WAN routes, which simplifies the creation of the deny 10.4.143.0 0.0.0.255
access-list. The specific IP addresses in use are shown in Table 8. permit any
router eigrp 100

Table 8. WAN IP Address Ranges distribute-list BLOCK-DIST-ROUTES-CE in
default-metric 100000 100 255 1 1500
IP Address Range Usage ACL Entry
network 10.4.0.0 0.0.255.255
10.5.0.0/16 Remote-Site LAN 10.5.0 0 0.0.255.255 redistribute bgp 65511
10.4.142.0/24 MPLS A PE-CE Links 10.4.142.0 0.0.0.255 passive-interface default
no passive-interface Port-channel1
10.4.143.0/24 MPLS B PE-CE Links 10.4.143.0 0.0.0.255 eigrp router-id 10.4.128.241
no auto-summary
This example includes all IP prefixes in use on the WAN remote-site LANs
and for the MPLS PE-CE links. Depending on the IP assignment in your
network, more IP prefixes may need to be blocked.

Step 3: Redistribute EIGRP into BGP.
Procedure 5 Configure BGP
All EIGRP routes learned by the CE router, including routes from the core
and for other WAN sites, should be advertised into the WAN. It is most
Procedure Steps: efficient if these routes have been summarized before being advertised to
the CE router.
1. Enable BGP.
2. Configure eBGP. Because BGP does not propagate a default route via redistribution, you
must explicitly specify 0.0.0.0 in a network statement.
3. Redistribute EIGRP into BGP. router bgp [ASN]
4. Configure iBGP (optional). network 0.0.0.0
redistribute eigrp 100
Step 1: Enable BGP.

Step 4: Configure iBGP (optional).
A BGP ASN is required to complete this step. You can consult with your
With dual MPLS carriers, a BGP link is configured between the CE routers.
MPLS carrier on the requirements for the ASN, but you may be permitted to
Since the CE routers are using the same ASN, this configuration is consid-
use a private ASN as designated by IANA. The private ASN range is 64512 to
ered an internal BGP (iBGP) connection. This design uses iBGP peering
65534.
using device loopback addresses, which requires the update-source and
The CE router only advertises network routes to the PE via BGP in the follow- next-hop-self-configuration options.
ing cases: router bgp [ASN]
neighbor [iBGP neighbor Loopback0] remote-as [ASN]
• The route is specified in network statements and is present in the local neighbor [iBGP neighbor Loopback0] update-source Loopback0
routing table neighbor [iBGP neighbor Loopback0] next-hop-self
• The route is redistributed into BGP (covered in Step 3)
router bgp [ASN] Procedure 5 Example
no synchronization router bgp 65511
bgp router-id [IP address of Loopback0] no synchronization
bgp log-neighbor-changes bgp router-id 10.4.128.241
no auto-summary bgp log-neighbor-changes
network 0.0.0.0
Step 2: Configure eBGP. network 10.4.142.0 mask 255.255.255.252
BGP must be configured with the MPLS carrier PE device. The MPLS carrier neighbor 10.4.128.242 remote-as 65511 ! Optional – dual
must provide their ASN (the ASN in Step 1 is the ASN identifying your site). MPLS only
Because the carrier PE router uses a different ASN, this configuration is con- neighbor 10.4.128.242 update-source
sidered an external BGP (eBGP) connection. Loopback0 ! Optional – dual
MPLS only
It is desirable to advertise a route for the PE-CE link, so this network should neighbor 10.4.128.242 next-hop-self ! Optional – dual
be included in a network statement. This is useful to determine router reach- MPLS only
ability for troubleshooting. neighbor 10.4.142.2 remote-as 65401
router bgp [ASN] no auto-summary
network [PE-CE link network] mask [PE-CE link netmask]
neighbor [IP address of PE] remote-as [carrier ASN]

interface Port-Channel1
Procedure 6 Configure IP Multicast Routing ip pim sparse-mode
!
This procedure applies to all WAN routers. ip pim sparse-mode
!
Procedure Steps: ip pim rp-address 10.4.60.252 10
1. Enable IP multicast routing. ip pim register-source Loopback0
access-list 10 permit 239.1.0.0 0.0.255.255
2. Configure PIM, RP and scoping
Step 1: Enable IP multicast routing. Process

Enable IP multicast routing on the platforms in the global configuration
mode.
ip multicast-routing WAN Distribution Switch Configuration
1. Finish Switch Universal Configuration
The Cisco ASR1000 Series router requires the distributed keyword 2. Connect to MPLS CE router
ip multicast-routing distributed
3. Connect to Core
Step 2: Configure PIM, RP and scoping. 4. Configure EIGRP
Every Layer 3 switch and router must be configured with the address of 5. Configure IP Multicast Routing
the IP multicast RP. Use the rp-address command in conjunction with
an access-list to limit the network size that the RP is responsible for. This
configuration provides for future scaling and control of the IP multicast
environment and can change based on network needs and design. The PIM Configuration
Procedure 1 Finish Switch Universal Configuration
source is configured to be the device loopback for resiliency at sites with
multiple WAN transports.
ip pim rp-address [IP address of RP] [ACL number] This guide assumes that the WAN distribution switch has already been
ip pim register-source Loopback0 configured. Only the procedures required to complete the connections of
access-list [ACL number] permit [multicast group scope] [inverse the MPLS CE router and core devices are included. Full details on distribu-
mask] tion layer switch configuration are included in the Cisco SBA for Large
Agencies—Borderless Networks LAN Deployment Guide.
All Layer 3 interfaces in the network must be enabled for sparse mode
multicast operation.
ip pim sparse-mode
Procedure 6 Example
!
interface Loopback0
ip pim sparse-mode
!

description bn-ce-1 port 2
Procedure 2 Connect to MPLS CE Router no switchport
no ip address
The port-channel interface connects to a MPLS VPN router and this connection channel-group 1 mode on
no shutdown
is a Layer 3 port channel. The following configuration creates an EtherChannel
link between the switch and router, with two channel-group members.
Procedure Steps: Procedure 3 Connect to Core
1. Configure the port-channel interface and assign the IP address.

2. Administratively enable the port-channel group members and assign This procedure is only required when the WAN deployment uses a separate
the appropriate channel group. dedicated WAN distribution switch. High-performance 10-Gbps interfaces
are used. The core consists of two devices. The single link to each core
device provides sufficient resiliency such that EtherChannel links are not
Step 1: Configure the port-channel interface and assign the IP address. required. The interfaces are configured as Layer 3 links.
As a best practice, use the same channel numbering on both sides of the The WAN switch generates IP route summaries for the WAN-aggregation
link where possible. block and for the remote sites. After the summaries have been configured,
interface Port-channel [number] EIGRP suppresses the advertisement of more specific routes within the
no switchport summaries.
no switchport
Step 2: Enable the port channel group members and assign the appropriate ip address [IP address] [netmask]
channel group. ip summary-address eigrp [as number] [summary network] [summary
Not all router platforms can support LACP to negotiate with the switch, so mask]
EtherChannel is configured statically. ip summary-address eigrp [as number] [summary network] [summary
mask]
no switchport
Procedure 3 Example
no ip address
channel-group [number] mode on interface TenGigabitEthernet1/0/1
no shutdown description Link to core (1)
no switchport
Procedure 2 Example
ip address 10.4.60.42 255.255.255.252
interface Port-channel1 ip summary-address eigrp 100 10.4.128.0 255.255.192.0
description bn-ce-1 EtherChannel ip summary-address eigrp 100 10.5.0.0 255.255.0.0
no switchport
ip address 10.4.128.1 255.255.255.252
ip summary-address eigrp 100 10.5.0.0 255.255.0.0
!
description bn-ce-1 port 1
no switchport
no ip address
channel-group 1 mode on
no shutdown
!

Procedure 4 Example
router eigrp 100
Procedure 4 Configure EIGRP network 10.4.0.0 0.0.255.255
Enable EIGRP for the IP address space that the network will be using. If needed no passive-interface TenGigabitEthernet1/0/1
for your network, you can enter multiple network statements. Disable auto no passive-interface TenGigabitEthernet2/0/1
no passive-interface Port-channel1
summarization of the IP networks and enable all routed links to be passive by
eigrp router-id 10.4.128.240
default. The Loopback 0 IP address is used for the EIGRP router ID to ensure no auto-summary
maximum resiliency. nsf
The single logical distribution layer design uses stateful switchover and
nonstop forwarding to provide sub-second failover in the event of a supervi-
sor data or control plane failure. This ability reduces packet loss in switcho- Procedure 5 Configure IP Multicast Routing
ver to redundant logic and keeps packets flowing when the data plane is
still intact to adjacent nodes. In the stack-based distribution layer approach,
a single logical control point still exists and the master control plane in a This procedure applies to all WAN routers and distribution layer LAN
stack can failover to another member in the stack providing near-second or switches.
sub-second resiliency. Procedure Steps:
When the supervisor or master switch of a distribution platform switches 1. Enable IP multicast routing.
over from the Active to the Hot-Standby supervisor, it will continue switching
2. Configure PIM, RP and scoping.
IP data traffic flows in hardware. However, the supervisor requires time to
reestablish control plane two-way peering with EIGRP routing neighbors and
avoid the peer router from tearing down adjacencies due to missed hellos Step 1: Enable IP multicast routing.
that would cause a reroute and disruption of traffic. To allow this time for
the supervisor to recover, there is a Nonstop Forwarding (NSF) setting for mode.
the routing protocol to wait for the dual supervisor peer switch to recover.
ip multicast-routing
The neighboring router is said to be NSF aware if it has a release of IOS that
recognizes an NSF peer. All of the platforms used in this design are NSF
aware for the routing protocols in use. The Cisco Catalyst 3750 Series Switch requires the distributed keyword
The distribution layer switch must be configured to enable Nonstop
Forwarding for the protocol in use so that it can signal a peer when it
Step 2: Configure PIM, RP and scoping.
switches over to a Hot-Standby supervisor for the peering neighbor to allow
it time to reestablish EIGRP protocol to that node. No tuning of the default Every Layer 3 switch and router must be configured with the address of the
NSF timers is needed in this network. Nothing has to be configured for an IP multicast RP. Use the rp-address command in conjunction with an access-
NSF aware peer router. list to limit the network size that the RP is responsible for. This configuration
provides for future scaling and control of the IP multicast environment and
router eigrp [as number] can change based on network needs and design. The PIM source is con-
network [network] [inverse mask] figured to be the device loopback for resiliency at sites with multiple WAN
passive-interface default transports.
no passive-interface [interface] ip pim rp-address [IP address of RP] [ACL number]
eigrp router-id [IP address of Loopback0] ip pim register-source Loopback0
no auto-summary access-list [ACL number] permit [multicast group scope] [inverse
nsf mask]

ip pim sparse-mode
Procedure 5 Example
!
interface Loopback0
ip pim sparse-mode
!
ip pim sparse-mode
!
interface TenGigabitEthernet1/0/1
ip pim sparse-mode
!
ip pim rp-address 10.4.60.252 10
ip pim register-source Loopback0

Figure 15. Remote-Site MPLS CE Router Configuration Flowchart
Process
Remote-Site MPLS CE Router Configuration

This section includes all required procedures for the configuration of a
MPLS CE router for a MPLS WAN remote site (single router, single link).
This set of procedures should also be used for a MPLS WAN + DMVPN
remote site. Use these procedures when performing the initial
configuration of a dual-role MPLS CE and DMVPN spoke router
in the single-router, dual-link design.
These procedures should also be used when configuring the first
router of the dual-router, dual-link design.
The flowchart in Figure 15 provides details on how to complete the
configuration of a remote-site MPLS CE router.
1. Complete the WAN Router Universal Configuration
2. Connect to the MPLS PE Router
3. Configure BGP
4. Configure IP Multicast Routing
5. Configure Access Layer Routing
The following procedures are only relevant for the dual router design:
6. Configure Access Layer HSRP Procedure 1 Finish WAN Router Universal Configuration
7. Configure Transit Network
8. Configure EIGRP (LAN side) Procedure Steps:
9. Enable Enhanced Object Tracking (EOT) 1. Configure the device hostname.
2. Configure in-band management.
3. Configure device-management protocols.
4. Configure secure user authentication.
5. Configure a synchronized clock.

Step 1: Configure the device hostname. line con 0
hostname [hostname] logging synchronous
Step 2: Configure in-band management interface. SNMP is enabled to allow the network infrastructure devices to be managed
by a NMS. SNMPv2c is configured both for a read-only and a read-write
All devices leverage a loopback address. A loopback is a virtual interface community string.
that is consistently reachable when multiple paths exist to the device. snmp-server community cisco RO
Various other features may use the loopback. snmp-server community cisco123 RW
interface Loopback0 snmp-server trap-source Loopback0
Step 4: Configure secure user authentication.
Step 3: Configure device-management protocols.
AAA is enabled for access control. All management access to the network
SSH is an application and a protocol that provides a secure replacement to infrastructure devices (SSH, Telnet, HTTP, and HTTPS) is controlled with
RSH and Telnet. Secure management access is enabled through the use of AAA. A local AAA user database is defined on the network infrastructure
the SSH and/or HTTPS protocols. HTTPS provides the capability to connect devices to provide the ability to manage them in case the centralized
a HTTP server securely. It uses SSL and TLS to provide device authentica- RADIUS server is unavailable, or if you do not have a RADIUS server in your
tion and data encryption. Both protocols are encrypted for privacy and the agency. We highly recommend the use of a centralized authentication
non-secure protocols, Telnet and HTTP, have been disabled. database.
ip domain-name cisco.local enable secret c1sco123
no ip http server service password-encryption
!
Enabling SSH requires that a public/private keypair be generated for username admin password c1sco123
the device: aaa new-model
aaa authentication login default group radius local
crypto key generate rsa modulus 2048 ip radius source-interface Loopback0
ip ssh version 2 radius-server host 10.4.200.15 key SecretKey
ip ssh source-interface Loopback0

Various levels of device management may be available through a web
interface. For secure access to this interface, you must enable the secure NTP is designed to synchronize a network of devices. An NTP network
server (the following command also generates a public/private keypair as usually gets its time from an authoritative time source, such as a radio clock
shown previously): or an atomic clock attached to a time server. NTP then distributes this time
ip http secure-server across the network. NTP is extremely efficient; no more than one packet per
minute is necessary to synchronize two devices to within a millisecond of
Allow only SSH access to the device: one another.
line vty 0 15 Network devices should be programmed to synchronize to a local NTP
transport input ssh server in the network. The local NTP server typically references a more
accurate clock feed from an outside source. Configuring console mes-
When synchronous logging of unsolicited messages and debug output sages, logs, and debug output on switches, routers, and other devices in the
is turned on, console log messages are displayed on the console after network to provide timestamps on output allows cross-referencing of events
interactive CLI output is displayed or printed. This command is also useful in a network.
for allowing you to continue typing at the device console when debugging ntp server 10.4.200.17
is enabled. ntp source Loopback0

ntp update-calendar ! this command not for use on ASR1000 interface [interface type] [number]
Series no cdp enable
! no shutdown
clock timezone PST -8
clock summer-time PDT recurring
Procedure 2 Example
!
service timestamps debug datetime msec localtime interface GigabitEthernet0/0
service timestamps log datetime msec localtime bandwidth 10000
ip address 10.4.142.153 255.255.255.252
no cdp enable
no shutdown
Procedure 2 Connect to MPLS PE Router
Procedure Steps: Procedure 3 Configure BGP
1. Assign the interface bandwidth.

Procedure Steps:
2. Assign the IP address and netmask of the WAN interface.
1. Enable BGP.
3. Administratively enable the interface and disable CDP.
2. Configure eBGP.
Step 1: Assign the interface bandwidth.
Step 1: Enable BGP.
The bandwidth value should correspond to the actual interface speed,
or if a sub-rate service is used, then the policed rate from the carrier should A BGP ASN is required to complete this step. It may be possible to reuse
be used. the same value used on the MPLS VPN CE from the WAN-aggregation site.
Consult with your MPLS carrier on the requirements for the ASN.
The example shows a Gigabit interface (1000 Mbps) with a sub-rate
of 10 Mbps. The CE router only advertises network routes to the PE via BGP in the follow-
ing cases:
Command Reference:
• The route is specified in network statements and is present in the local
bandwidth kbps
routing table
NOTE: 10 Mbps = 10000 kbps
• The route is redistributed into BGP (not applicable in the remote-site
use case)
bandwidth [bandwidth (kbps)]
router bgp [ASN]
no synchronization
Step 2: Assign the IP address and netmask of the WAN interface. bgp router-id [IP address of Loopback0]
The IP addressing used between CE and PE routers must be negotiated with bgp log-neighbor-changes
no auto-summary
your MPLS carrier. Typically a point-to-point netmask of 255.255.255.252 is
used.
interface [interface type] [number] Step 2: Configure eBGP.
ip address [IP address] [netmask] BGP must be configured with the MPLS carrier PE device. The MPLS carrier
must provide their ASN (the ASN in Step 1 is the ASN identifying your site).
Step 3: Administratively enable the interface and disable CDP. Since the carrier PE router will use a different ASN, this configuration is
considered an external BGP (eBGP) connection.
We do not recommend the use of CDP on external interfaces.

It is desirable to advertise a route for the PE-CE link, so this network should Step 2: Configure PIM, RP and scoping.
be included in a network statement. This is useful to determine router reach-
Every Layer 3 switch and router must be configured with the address of the
ability for troubleshooting.
IP multicast RP. Use the rp-address command in conjunction with an access-
The remote-site LAN networks must be advertised. The IP assignment for list to limit the network size that the RP is responsible for. This configuration
the remote sites was designed so that all of the networks in use can be provides for future scaling and control of the IP multicast environment and
summarized within a single aggregate route. The aggregate address as can change based on network needs and design. The PIM source is
configured below suppresses the more specific routes. If any LAN network configured to be the device loopback for resiliency at sites with multiple
is present in the route table, the aggregate is advertised to the MPLS PE, WAN transports.
which offers a measure of resiliency. If the various LAN networks can not be ip pim rp-address [IP address of RP] [ACL number]
summarized, then each must be listed individually. ip pim register-source Loopback0
router bgp [ASN] access-list [ACL number] permit [multicast group scope] [inverse
network [PE-CE link network] mask [PE-CE link netmask] mask]
network [LAN network 1] mask [LAN network 1 netmask]
network [LAN network 2] mask [LAN network 2 netmask] All Layer 3 interfaces in the network must be enabled for sparse mode
aggregate-address [summary IP address] [summary netmask] multicast operation.
summary-only
neighbor [IP address of PE] remote-as [carrier ASN]
ip pim sparse-mode
Procedure 3 Example
Procedure 4 Example
router bgp 65511
no synchronization
!
bgp router-id 10.5.48.254
interface Loopback0
bgp log-neighbor-changes
ip pim sparse-mode
network 10.4.142.152 mask 255.255.255.252
!
network 10.5.52.0 mask 255.255.255.0
interface GigabitEthernet0/0
network 10.5.53.0 mask 255.255.255.0
ip pim sparse-mode
aggregate-address 10.5.48.0 255.255.248.0 summary-only
!
neighbor 10.4.142.154 remote-as 65401
interface GigabitEthernet0/2.64
no auto-summary
ip pim sparse-mode
!
Procedure 4 Configure IP Multicast Routing ip pim register-source Loopback0
This procedure applies to all WAN routers.
Procedure Steps: Procedure 5 Configure Access Layer Routing
1. Enable IP multicast routing.
Procedure Steps:
2. Configure PIM, RP and scoping.
1. Enable the physical interface.
Step 1: Enable IP multicast routing. 2. Create subinterfaces and assign VLAN tags.
Enable IP multicast routing on the platforms in the global 3. Configure IP settings for each subinterface.
configuration mode.

In the access layer design, the remote-sites use collapsed routing, with encapsulation dot1Q 64
802.1Q trunk interfaces to the LAN access layer. The VLAN numbering is ip address 10.5.52.1 255.255.255.0
locally significant only. The access switches are Layer 2 only. ip helper-address 10.4.200.10
ip pim sparse-mode
!
Step 1: Enable the physical interface. interface GigabitEthernet0/2.65
interface [interface type] [number] description WirelessData
no ip address encapsulation dot1Q 65
no shutdown ip address 10.5.50.1 255.255.255.0
ip helper-address 10.4.200.10
ip pim sparse-mode
Step 2: Create subinterfaces and assign VLAN tags. !
After the physical interface has been enabled, then the appropriate data or interface GigabitEthernet0/2.69
voice subinterfaces can be mapped to the VLANs on the LAN switch. The description Voice
encapsulation dot1Q 69
subinterface number does not need to equate to the 802.1Q tag, but making
ip address 10.5.53.1 255.255.255.0
them the same simplifies the overall configuration. The subinterface portion ip helper-address 10.4.200.10
of the configuration should be repeated for all data or voice VLANs. ip pim sparse-mode
interface [interface type] [number].[sub-interface number] !
encapsulation dot1Q [dot1q VLAN tag] interface GigabitEthernet0/2.70
description WirelessVoice
Step 3: Configure IP settings for each subinterface. encapsulation dot1Q 70
ip address 10.5.51.1 255.255.255.0
This design uses an IP addressing convention with the default gateway ip helper-address 10.4.200.10
router assigned an IP address and IP mask combination of N.N.N.1 ip pim sparse-mode
255.255.255.0 where N.N.N is the IP network and 1 is the IP host.
All router LAN interfaces that use DHCP for end-station IP assignment must
use an IP helper to reach a centralized DHCP server in this design. The following procedures (6–9) are only relevant for the
dual-router design
If the remote-site MPLS CE router is the first router of a dual-router design,
then HSRP is configured at the access layer. This requires a modified IP
configuration on each subinterface. For the modified procedure, you should Procedure 6 Configure Access Layer HSRP
skip to Procedure 6 after completing Steps 1 and 2. [Dual-Router Design Only]
interface [interface type] [number].[sub-interface number]
encapsulation dot1Q [dot1q VLAN tag] HSRP is configured to enable the use of a Virtual IP (VIP) to be used as a
ip address [LAN network 1] LAN network 1 [netmask]
default gateway that is shared between two routers. The HSRP active router
ip helper-address [IP address of DHCP server]
is the MPLS CE router and the HSRP standby router is the DMVPN spoke
router. Configure the MPLS CE router with a standby priority that is higher than
Procedure 5 Example the DMVPN spoke router.
no ip address The router with the higher standby priority value is elected as the HSRP
no shutdown Active router. The preempt option allows a router with a higher priority to
! become the HSRP Active, without waiting for a scenario where there is no
! router in the HSRP Active state. The relevant HSRP parameters for the router
interface GigabitEthernet0/2.64 configuration are shown in Table 9.
description Data

Table 9. WAN Remote-Site HSRP Parameters (Dual Router) Procedure 6 Example—MPLS CE Router
interface GigabitEthernet0/2.64
Virtual IP description Data
HSRP Address Real IP HSRP PIM DR encapsulation dot1Q 64
Router Role (VIP) Address Priority Priority ip address 10.5.52.2 255.255.255.0
MPLS CE Active .1 .2 110 110 ip helper-address 10.4.200.10
ip pim dr-priority 110
DMVPN Spoke Standby .1 .3 105 105 ip pim sparse-mode
standby 1 ip 10.5.52.1
standby 1 priority 110
The assigned IP addresses override those configured with the previous proce-
standby 1 preempt
dure 5, so the default gateway IP address remains consistent across locations
with single or dual routers.
The dual-router access-layer design requires a modification for resilient Procedure 7 Configure Transit Network
[Dual-Router Design Only]
multicast. The PIM designated router (DR) should be on the HSRP active
router. The DR is normally elected based on the highest IP address, and has The transit network is configured between the two routers. This network is
no awareness of the HSRP configuration. In this design, the HSRP active used for router-router communication and to avoid hair-pinning. The transit
router has a lower real IP address than the HSRP standby router, which network should use an additional subinterface on the router interface that is
requires a modification to the PIM configuration. The PIM DR election can be already being used for data or voice.
influenced by explicitly setting the DR priority on the LAN-facing subinter-
faces for the routers. There are no end stations connected to this network so HSRP and DHCP are
not required.
encapsulation dot1Q [dot1q VLAN tag]
Tech Tip ip address [transit net address] [transit net netmask]
The HSRP priority and PIM DR priority are shown in Table 9 to be the Procedure 7 Example—MPLS CE Router
same value; however there is no requirement that these values must be interface GigabitEthernet0/2.99
identical. description Transit Net
ip address 10.5.48.1 255.255.255.252
This procedure should be repeated for all data or voice subinterfaces.
encapsulation dot1Q [dot1q VLAN tag] Procedure 8 Configure EIGRP (LAN Side)
ip address [LAN network 1 address] [LAN network 1 netmask]
A routing protocol must be configured between the two routers. This ensures
ip pim sparse-mode
ip pim dr-priority [PIM DR priority] that the HSRP active router has full reachability information for all WAN
standby [number] ip [LAN network 1 gateway address] [LAN remote sites.
network 1 netmask] Procedure Steps:
standby [number] priority [priority]
standby [number] preempt 1. Enable EIGRP-100.
2. Redistribute BGP into EIGRP-100.

Step 1: Enable EIGRP-100. router would learn an alternate path through the transit network to the
DMVPN router and begin to forward traffic across the alternate path. This is
EIGRP-100 is configured facing the access layer. In this design, all LAN-
sub-optimal routing, and can be addressed through the use of EOT.
facing interfaces and the loopback must be EIGRP interfaces. All interfaces
except the transit-network subinterface should remain passive. The network The HSRP active router (MPLS CE) can use the IP SLA feature to send echo
range must include all interface IP addresses either in a single network probes to the MPLS PE router and if the PE router becomes unreachable,
statement or in multiple network statements. This design uses a best prac- then the router can lower its HSRP priority, so that the HSRP standby router
tice of assigning the router ID to a loopback address. Do not include the can preempt and become the HSRP Active router.
WAN interface (MPLS PE-CE link interface) as an EIGRP interface.
This procedure is valid only on the router connected to the primary transport
router eigrp [as number] (MPLS VPN).
passive-interface default Procedure Steps:
no passive-interface [interface]
eigrp router-id [IP address of Loopback0] 1. Enable the IP SLA probe.
no auto-summary 2. Configure EOT.
3. Link HSRP with the tracked object.
Step 2: Redistribute BGP into EIGRP-100.
The BGP routes are redistributed into EIGRP with a default metric. By Step 1: Enable the IP SLA probe.
Standard ICMP echo (ping) probes are used, and are sent at 15 second
Command Reference: intervals. Responses must be received before the timeout of 1000 ms
default-metric bandwidth delay reliability loading mtu expires. If using the MPLS PE router as the probe destination, the destina-
bandwidth Minimum bandwidth of the route in kilobytes per second tion address is the same as the BGP neighbor address configured in
Procedure 2.
delay Route delay in tens of microseconds.
ip sla [probe number]
router eigrp [as number] icmp-echo [probe destination IP address] source-interface
default-metric [bandwidth] [delay] 255 1 1500 [WAN interface]
redistribute bgp [BGP ASN] timeout 1000
threshold 1000
Procedure 8 Example frequency 15
router eigrp 100 ip sla schedule [probe number] life forever start-time now
default-metric 100000 100 255 1 1500
network 10.5.0.0 0.0.255.255 Step 2: Configure EOT.
redistribute bgp 65511
passive-interface default A tracked object is created based on the IP SLA probe. The object being
no passive-interface GigabitEthernet0/2.99 tracked is the reachability success or failure of the probe. If the probe is
eigrp router-id 10.5.48.254 successful, the tracked object status is Up; if it fails, the tracked object
no auto-summary status is Down.
track [tracked object number] ip sla [probe number]
reachability
Procedure 9 Enable Enhanced Object Tracking
The HSRP active router remains the active router unless the router is reloaded
or fails. Having the HSRP router remain as the active router can lead to
undesired behavior. If the MPLS VPN transport were to fail, the HSRP active

Step 3: Link HSRP with the tracked object. Deploying a DMVPN WAN
All data or voice subinterfaces should enable HSRP tracking. DMVPN WAN Agency Overview
HSRP can monitor the tracked object status. If the status is down, the HSRP Agencies require the WAN to provide sufficient performance and reliability
priority is decremented by the configured priority. If the decrease is large for the remote-site users to be effective in supporting the agency. Although
enough, the HSRP standby router preempts. most of the applications and services that the remote-site worker uses are
interface [interface type] [number].[sub-interface number] centrally located, the WAN design must provide a common resource access
encapsulation dot1Q [dot1q VLAN tag] experience to the workforce, regardless of location.
ip address [LAN network 1 address] [LAN network 1 netmask]
standby [number] ip [LAN network 1 gateway address] [LAN Carrier-based MPLS service is not always available or cost-effective for an
network 1 netmask] agency to use for WAN transport to support remote-site connectivity.
standby [number] priority [priority] Internet-based IP VPNs provide an optional transport that can be used as a
standby [number] preempt resilient backup to a primary MPLS network transport or may be adequate
standby [number] track [tracked object number] decrement to provide the primary network transport for a remote site. Flexible network
[priority] architecture should include Internet VPN as a transport option without
significantly increasing the complexity of the overall design.
Procedure 9 Example
While Internet IP VPN networks present an attractive option for effective
interface GigabitEthernet0/2.64 WAN connectivity, anytime an agency sends data across a public network
description Data
there is risk that the data will be compromised. Loss or corruption of data
ip address 10.5.52.2 255.255.255.0 can result in a regulatory violation and can present a negative public image,
ip helper-address 10.4.200.10 either of which can have significant financial impact on an agency. Secure
standby 1 ip 10.5.52.1 data transport over public networks like the Internet requires adequate
standby 1 priority 110 encryption to protect agency information.
standby 1 preempt
DMVPN WAN Technical Overview
standby 1 track 50 decrement 10
! WAN 500 Design
track 50 ip sla 100 reachability
! The WAN 500 design is intended to support up to 500 remote sites with a
ip sla 100 combined aggregate WAN bandwidth of up to 1.0 Gbps. The most critical
icmp-echo 10.4.142.154 source-interface GigabitEthernet0/0 devices are the WAN routers that are responsible for reliable IP forwarding
timeout 1000 and QoS. This design uses the Cisco ASR1002 Aggregation Services Router
threshold 1000 for the DMVPN hub router. The WAN 500 design uses a single Internet
frequency 15 service provider and a single DMVPN hub router as shown in Figure 16.
ip sla schedule 100 life forever start-time now
The DMVPN VPN router connects to the Internet indirectly through a firewall
Demilitarized Zone (DMZ) interface contained within the Internet edge.
Further details of the primary site Internet connection are referenced in the
Cisco SBA for Large Agencies—Borderless Networks Internet Edge
Deployment Guide. The VPN hub router is connected into the firewall DMZ
interface, rather than connected directly with an Internet service provider
router.

Figure 16. WAN 500 Design—DMVPN Connection 3945E Integrated Services Router for the DMVPN hub router. The WAN 100
design uses a single Internet service provider and a single DMVPN hub
router as shown in Figure 17.
Figure 17. WAN 100 Design—DMVPN Connection
The Cisco ASR1000 Series Aggregation Services Routers represent the Remote Sites—DMVPN Spoke Router Selection
next-generation, modular, services-integrated Cisco routing platform. They
are specifically designed for WAN aggregation, with the flexibility to sup- The actual WAN remote-site routing platforms remain unspecified because
port a wide range of 4- to 16-Mpps packet-forwarding capabilities, 2.5- to the specification is tied closely to the bandwidth required for a location and
20-Gbps system bandwidth performance, and scaling. The Cisco ASR 1000 the potential requirement for the use of service module slots. The ability to
Series is fully modular, from both hardware and software perspectives, and implement this solution with a variety of potential router choices is one of the
the routers have all the elements of a true carrier-class routing product that benefits of a modular design approach.
serves both large-agency and service-provider networks. There are many factors to consider in the selection of the WAN remote-site
WAN 100 Design routers. Among those, and key to the initial deployment, is the ability to
process the expected amount and type of traffic. Also we need to be con-
The WAN 100 design is intended to support up to 100 remote sites with cerned with having enough interfaces, enough module slots, and a properly
a combined aggregate WAN bandwidth of up to 100 Mbps. The WAN 100 licensed Cisco IOS image that supports the set of features that is required
design is essentially a smaller scale version of the WAN 500 design. This by the topology. We tested four integrated service router models as DMVPN
variant is included to provide a limited scale option. If further growth in spoke routers and the expected performance is shown in Table 10.
bandwidth or an increase in the number of sites is expected, then proceed
with the WAN 500 design. Using the larger design can prevent unnecessary
downtime associated with device upgrades. This design uses the Cisco

Table 10. WAN Remote-Site Router Options Figure 18. DMVPN Remote Site (Single Link—Single Router)
2911 2921 3925 3945

Ethernet WAN with Services 1
35 Mbps 50 Mbps 100 150
Mbps Mbps
On-board GE ports 3 3 3 3
Service Module Slots 2
1 2 2 4
Redundant Power Supply No No Yes Yes
Option
Notes:
1. The performance numbers are conservative numbers obtained when the
router is passing IMIX traffic with heavy services configured and the CPU
utilization is under 75 percent.
2. Some service modules are double-wide.
The DMVPN spoke routers at the WAN remote sites connect to the Internet
directly through a router interface. More details about the security configu-
ration of the remote-site routers connected to the Internet are discussed
later in this guide. The single link DMVPN remote site shown in Figure 18 is
the most basic of building blocks for any remote location. This design can The DMVPN connection can be the primary WAN transport, or can also be
be used with the CE router connected directly to the access layer, or it can the alternate to an MPLS WAN transport. The DMVPN single-link design can
support a more complex LAN topology by connecting the CE router directly be added to an existing MPLS WAN design to provide additional resiliency
to a distribution layer. either connecting on the same router or on an additional router. These
alternate designs are shown in Figure 19. Adding an additional link provides
The IP routing is straightforward and can be handled entirely by static the first level of high availability for the remote site. A failure in the primary
routing; using static routes at the WAN-aggregation site and static default link can be automatically detected by the router and traffic can be rerouted
routes at the remote site. However, there is significant value to configuring to the secondary path. It is mandatory to run dynamic routing when there are
this type of site with dynamic routing. It is easy to add or modify IP networks multiple paths. The routing protocols are tuned to ensure the desired
at the remote site when using dynamic routing because any changes are traffic flows.
immediately propagated to the rest of the network.
The dual-router, dual-link design continues to improve upon the level of
high availability for the site. This design can tolerate the loss of the primary
router and traffic can be rerouted via the secondary router (through the
alternate path).

Figure 19. MPLS WAN + DMVPN Remote Site (Dual Link Options) The multiple default route conundrum is solved through the use of VRFs on
the router. A router can have multiple routing tables that are kept logically
separate on the device. This separation is similar to a virtual router from the
forwarding plane perspective. The global VRF corresponds to the traditional
routing table, and additional VRFs are given names and route descriptors
(RDs). Certain features on the router are VRF aware, including static routing
and routing protocols, interface forwarding and IPSec tunneling. This set
of features is used in conjunction with DMVPN to permit the use of multiple
default routes for both the DMVPN hub routers and DMVPN spoke routers.
This combination of features is referred to as Front Door VRF (F-VRF),
because the VRF faces the Internet and the router internal interfaces and
the mGRE tunnel all remain in the global VRF. See Figure 20 for the architec-
ture details. More technical details regarding Front Door VRF can be found
in the Technical Feature Supplement appendix.
Figure 20. Front Door VRF
VRFs and Front Door VRF

Virtual Routing and Forwarding (VRF) is a technology used in computer net-
works that allows multiple instances of a routing table to co-exist within the
same router at the same time. Because the routing instances are indepen-
dent, the same or overlapping IP Addresses can be used without conflicting
with each other. Often in a MPLS context, VRF is also defined as VPN Routing
and Forwarding.
VRF may be implemented in a network device by having distinct routing
tables, also known as forwarding information bases (FIBs), one per VRF.
Alternatively, a network device may have the ability to configure different
virtual routers, where each one has its own FIB that is not accessible to any
other virtual router instance on the same device.
The simplest form of VRF implementation is VRF Lite. In this implementation,
each router within the network participates in the virtual routing environment
on a peer-by-peer basis. VRF Lite configurations are only locally significant.
The IP routing policy used in this design for the WAN remote sites does not
allow direct Internet access for web browsing or other uses; any remote-site
hosts that access the Internet must do so via the Internet edge at the pri-
mary site. The end hosts require a default route for all Internet destinations;
however, this route must force traffic across the primary or secondary WAN
transports (MPLS VPN or DMVPN tunnel). This requirement conflicts with the
more general VPN spoke router requirement for an Internet-facing default
route to bring up the VPN tunnel.

Design Details Figure 21. WAN500/100 Designs—DMVPN Routing Detail
The DMVPN hub router connects to a resilient switching device in the distribu-
tion layer and in the DMZ. The DMVPN router uses EtherChannel connec-
tions consisting of two port bundles. This design provides both resiliency
and additional forwarding performance. Additional forwarding performance
can be accomplished by increasing the number of physical links within an
EtherChannel.
The DMVPN hub routers are required to have sufficient IP-routing informa-
tion to provide end-to-end reachability. Maintaining this routing information
typically requires a routing protocol, and EIGRP is used for this purpose.
Two separate EIGRP processes are used, one for internal routing on the
LAN (EIGRP-100) and one for the DMVPN (EIGRP-200). The primary reason
for the separate EIGRP processes is to simplify the route selection at the
WAN-aggregation site when using a MPLS WAN primary path and a DMVPN
alternate path. This method ensures that both MPLS learned routes and EIGRP
DMVPN learned routes appear as EIGRP external routes after they are
redistributed into the EIGRP-100 process used on the campus LAN. We chose EIGRP as the primary routing protocol because it is easy to
configure, does not require a large amount of planning, has flexible sum-
At the WAN-aggregation site, the DMVPN router must be connected to the marization and filtering, and can scale to large networks. As networks grow,
distribution layer and to the DMZ-VPN that provides Internet connectivity. the number of IP prefixes or routes in the routing tables grows as well. You
The DMVPN hub routers use Front Door VRF and have a static default route should program IP summarization on links where logical boundaries exist,
with the INET-PUBLIC VRF pointing to the firewall DMZ interface. The IP like distribution layer links to the wide area or to a core. By performing IP
routing details for the DMVPN WAN-aggregation topology are shown in summarization, you can reduce the amount of bandwidth, processor, and
Figure 21. memory necessary to carry large route tables, and reduce convergence
time associated with a link failure.
In this design, EIGRP process 100 is the primary EIGRP process and is
referred to as EIGRP-100.
EIGRP-100 is used at the WAN-aggregation site to connect to the primary
site LAN distribution layer and at WAN remote sites with dual WAN routers or
with distribution-layer LAN topologies. EIGRP-200 is used for the
DMVPN tunnels.
Encryption
The primary goal of encryption is to provide data confidentiality, integrity,
and authenticity by encrypting IP packets as the data travels across
a network.
The encrypted payloads are then encapsulated with a new header (or mul-
tiple headers) and transmitted across the network. The additional headers
introduce a certain amount of overhead to the overall packet length. Table
11 highlights the packet overhead associated with encryption based on the
additional headers required for various combinations of IPsec and GRE.

Table 11. Overhead Associated with IPsec and GRE DMVPN
Encapsulation Overhead This solution uses the Internet for WAN transport. For data security and
privacy concerns any site-to-site traffic that traverses the Internet must be
GRE only 24 bytes
encrypted. Multiple technologies can provide encryption, but the method
IPsec (Transport Mode) 36 bytes that provides the best combination of performance, scale, application sup-
IPsec (Tunnel Mode) 52 bytes port, and ease of deployment is Dynamic Multipoint VPN.
IPsec (Transport Mode) + GRE 60 bytes Most use cases in this design guide use Internet/DMVPN as a secondary
IPsec (Tunnel Mode) + GRE 76 bytes WAN transport that requires a DMVPN single-cloud, single-hub design as
shown in Figure 22. The DMVPN routers use tunnel interfaces that support
There is a Maximum Transfer Unit (MTU) parameter for every link in an IP unicast as well as IP multicast and broadcast traffic, including the use of
IP network and typically the MTU is 1500 bytes. IP packets larger than dynamic routing protocols. After the initial spoke-to-hub tunnel is active, it
1500 bytes must be fragmented when transmitted across these links. is possible to create dynamic spoke-to-spoke tunnels when site-to-site IP
Fragmentation is undesired and can impact network performance. To avoid traffic flows require it.
fragmentation, the original packet size plus overhead must be 1500 bytes or
less, which means that the sender must reduce the original packet size. To The information required by a spoke to set up dynamic spoke-to-spoke
account for other potential overhead, we recommend that tunnel interfaces tunnels and properly resolve other spokes is provided through the Next Hop
are configured with a 1400 byte MTU. Resolution Protocol (NHRP). Spoke-to-spoke tunnels allow for the optimal
routing of traffic between locations without indirect forwarding through
There are dynamic methods for network clients to discover the path MTU, the hub. Idle spoke-to-spoke tunnels gracefully time out after a period
which allow the clients to reduce the size of packets they transmit. However, of inactivity.
in many cases, these dynamic methods are unsuccessful, typically because
security devices filter the necessary discovery traffic. This failure to dis-
cover the path MTU drives the need for a method that can reliably inform
network clients of the appropriate packet size. The solution is to implement
the ip tcp adjust mss [size] command on the WAN routers, which influ-
ences the TCP Maximum Segment Size (MSS) value reported by end hosts.
The MSS defines the maximum amount of data that a host is willing to
accept in a single TCP/IP datagram. The MSS value is sent as a TCP header
option only in TCP SYN segments. Each side of a TCP connection reports
its MSS value to the other side. The sending host is required to limit the size
of data in a single TCP segment to a value less than or equal to the MSS
reported by the receiving host.
The IP and TCP headers combine for 40 bytes of overhead, so the typical
MSS value reported by network clients will be 1460. This design includes
encrypted tunnels with a 1400 byte MTU, so the MSS used by endpoints
should be configured to be 1360 to minimize any impact of fragmentation.
This ip tcp adjust mss 1360 command is implemented on all WAN facing
router interfaces in this solution.

Figure 22. DMVPN Single Cloud which is essential to facilitate fast reconvergence and for spoke registration
to function properly in case a DMVPN hub is reloaded. This design enables
a spoke to detect that an encryption peer has failed and that the ISAKMP
session with that peer is stale, which then allows a new one to be created.
Without DPD, the IPsec Security Association (SA) must time out (the default
is 60 minutes) and when the router cannot renegotiate a new SA, a new ISAKMP
session is initiated. The maximum wait time is approximately 60 minutes.
One of the key benefits of the DMVPN solution is that the spoke routers can
use dynamically assigned addresses, often using DHCP from an Internet
provider. The spoke routers can leverage an Internet default route for reach-
ability to the hub routers and also other spoke addresses.
Process
DMVPN Hub Router Configuration

2. Connect to the Distribution Switch
3. Configure VRF Lite
4. Connect to the Internet DMZ
5. Configure ISAKMP and IPSec
6. Configure the mGRE Tunnel
7. Configure EIGRP
The DMVPN hub router has a static IP address assigned to its public-facing Procedure 1 Finish WAN Router Universal Configuration
interface. This configuration is essential for proper operation as each of the
spoke routers has this IP address embedded in their configurations.
Procedure Steps:
It is common for a firewall to be placed between the DMVPN hub router
and the Internet. In many cases, the firewall may provide Network Address 1. Configure the device hostname.
Translation (NAT) from an internal RFC-1918 IP address (such as 10.4.128.33) 2. Configure in-band management.
to an Internet-routable IP address. The DMVPN solution works well with
NAT but requires the use of IPsec transport mode to support a DMVPN hub 3. Configure device-management protocols.
behind static NAT. 4. Configure secure user authentication.
DMVPN requires the use of Internet Security Association and Key 5. Configure a synchronized clock.
Management Protocol (ISAKMP) keepalives for Dead Peer Detection (DPD),

a HTTP server securely. It uses SSL and TLS to provide device authentica- RADIUS server is unavailable, or if you do not have a RADIUS server in
tion and data encryption. Both protocols are encrypted for privacy and the your agency. We highly recommend the use of a centralized authentication
!
Enabling SSH requires that a public/private keypair be generated for the username admin password c1sco123
device: aaa new-model

interface. For secure access to this interface you must enable the secure NTP is designed to synchronize a network of devices. An NTP network
for allowing you to continue typing at the device console when debugging is
enabled.

ntp server 10.4.200.17 Procedure 2 Example
ntp source Loopback0
Series
!
clock timezone PST -8
clock summer-time PDT recurring
!
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
Procedure 2 Connect to Distribution Switch
A Layer 3 port-channel interface connects to the WAN distribution switch.

The following configuration creates an EtherChannel link between the router
and switch, with two channel-group members.
Procedure Steps:
1. Configure the port-channel interface and assign an IP address.
2. Administratively enable the port-channel group members and assign
the appropriate channel group.
Step 1: Configure the port-channel interface and assign an IP address.

As a best practice, use the same channel numbering on both sides of the
link where possible.
interface Port-channel [number] interface Port-channel3
ip address [IP address] [netmask] ip address 10.4.128.18 255.255.255.252
!
Step 2: Enable the port channel group members and assign the appropriate interface GigabitEthernet0/0/0
no ip address
channel group.
channel-group 3
Not all router platforms can support LACP to negotiate with the switch, so no shutdown
EtherChannel is configured statically. !
interface [interface type] [number] interface GigabitEthernet0/0/1
no ip address no ip address
channel-group [number] channel-group 3
no shutdown no shutdown

Procedure Steps:
Procedure 3 Configure VRF Lite
1. Administratively enable the interface, select the VRF, and assign the
IP address.
An Internet-facing VRF is created to support Front Door VRF for DMVPN. 2. Configure the VRF-specific default routing.
The VRF name is arbitrary but it is useful to select a name that describes
the VRF. An associated route distinguisher (RD) must also be configured to
make the VRF functional. The RD configuration also creates the routing and Step 1: Enable the interface, select the VRF, and assign the IP address.
forwarding tables and associates the RD with the VRF instance. The IP address used for the Internet-facing interface of the DMVPN hub
This design uses VRF Lite so the RD value can be chosen arbitrarily. It is a router must be an Internet routable address. There are two possible meth-
best practice to use the same VRF/RD combination across multiple devices ods to accomplish this task:
when using VRFs in a similar manner. However, this convention is not strictly • Assign a routable IP address directly to the router
required.
• Assign a non-routable RFC-1918 address directly to the router and use a
Command Reference: static NAT on the Cisco ASA5500 to translate the router IP address to a
An RD is either of the following: routable IP address.
• ASN-related—Composed of an ASN and an arbitrary number. This design assumes that the Cisco ASA5500 is configured for static NAT
• I P-address-related—Composed of an IP address and an arbitrary for the DMVPN hub router.
number. The DMVPN design is using Front Door VRF, so this interface must be
You can enter an RD in either of these formats: placed into the VRF configured in the previous procedure.
16-bit autonomous-system-number:your 32-bit number ip vrf forwarding [vrf name]
For example, 65512:1. ip address [IP address] [netmask]
no shutdown
32-bit IP address: your 16-bit number
For example, 192.168.122.15:1. Step 2: Configure the VRF specific default routing.
ip vrf [vrf-name]
rd [ASN:number] The VRF created for Front Door VRF must have its own default route to the
Internet. This default route points to the ASA5500 DMZ interface IP address.
Procedure 3 Example ip route vrf [vrf name] 0.0.0.0 0.0.0.0 [ASA5500 DMZ interface
IP address]
ip vrf INET-PUBLIC
rd 65512:1
Procedure 4 Connect to Internet DMZ
The DMVPN hub requires a connection to the Internet, and in this design
the DMVPN hub is connected through a Cisco ASA5500 Adaptive Security
Appliance using a DMZ interface specifically created and configured for a
VPN termination router.

Procedure 4 Example key if it applies to any IP source. A wildcard key is configured using the
0.0.0.0 0.0.0.0 network/mask combination.
crypto keyring [keyring name] vrf [vrf name]
pre-shared-key address 0.0.0.0 0.0.0.0 key [pre-shared key]
Step 2: Configure the ISAKMP policy.

The ISAKMP policy for DMVPN uses the following:
• Advanced Encryption Standard (AES) with a 256-bit key
• Secure Hash Standard (SHA)
• Authentication by pre-shared key
• Diffie-Hellman group: 2
crypto isakmp policy 10
encr aes 256
hash sha
authentication pre-share
group 2
Step 3: Create the ISAKMP Profile

ip vrf forwarding INET-PUBLIC The ISAKMP profile creates an association between an identity address, a
ip address 10.4.128.33 255.255.255.248 VRF, and a crypto keyring. A wildcard address within a VRF is referenced
no shutdown with 0.0.0.0.
! crypto isakmp profile [ISAKMP profile name]
ip route vrf INET-PUBLIC 0.0.0.0 0.0.0.0 10.4.128.35 keyring [keyring name]
match identity address 0.0.0.0 [vrf name]
Procedure 5 Configure ISAKMP and IPSec Step 4: Define the IPsec transform set.
A transform set is an acceptable combination of security protocols, algo-
Procedure Steps: rithms, and other settings to apply to IPsec-protected traffic. Peers agree to
1. Configure the crypto keyring. use a particular transform set when protecting a particular data flow.
2. Configure the ISAKMP policy. The IPsec transform set for DMVPN uses the following:
3. Create the ISAKMP profile. • ESP with the 256-bit AES encryption algorithm
4. Define the IPSec transform set. • ESP with the SHA (HMAC variant) authentication algorithm
5. Create the IPSec profile. Because the DMVPN hub router is behind a NAT device, the IPsec transform
must be configured for transport mode.
Step 1: Configure the crypto keyring. crypto ipsec transform-set [IPSec transform-set name] esp-aes
256 esp-sha-hmac
The crypto keyring defines a pre-shared key (or password) valid for IP mode transport
sources reachable within a particular VRF. This key is a wildcard pre-shared

Step 5: Create the IPSec profile. Step 1: Configure basic interface settings.
The IPsec profile creates an association between an ISAKMP profile and an Tunnel interfaces are created as they are configured. The tunnel number is
IPsec transform-set. arbitrary, but it is best to begin tunnel numbering at 10 or above, because
crypto ipsec profile [IPSec profile name] other features deployed in this design may also require tunnels and they
set transform-set [IPSec transform-set name] may select lower numbers by default.
set isakmp-profile [ISAKMP profile name] The bandwidth setting should be set to match the Internet bandwidth of the
respective primary or secondary carrier.
Procedure 5 Example The IP MTU should be configured to 1400 and the ip tcp adjust-mss should
crypto keyring DMVPN-KEYRING vrf INET-PUBLIC be configured to 1360. There is a 40 byte difference which corresponds to
pre-shared-key address 0.0.0.0 0.0.0.0 key cisco123 the combined IP and TCP header length.
interface Tunnel [number]
crypto isakmp policy 10 bandwidth [bandwidth (kbps)]
encr aes 256 ip address [IP address] [netmask]
hash sha no ip redirects
authentication pre-share ip mtu 1400
group 2 ip tcp adjust-mss 1360
crypto isakmp profile FVRF-ISAKMP-INET-PUBLIC
keyring DMVPN-KEYRING Step 2: Configure the tunnel.
match identity address 0.0.0.0 INET-PUBLIC DMVPN uses multipoint GRE (mGRE) tunnels. This type of tunnel requires
a source interface only. The source interface should be the same interface
crypto ipsec transform-set AES256/SHA/TRANSPORT esp-aes 256 esp-
used in Procedure 6 to connect to the Internet. The tunnel vrf command
sha-hmac
mode transport should be set to the VRF defined previously for Front Door VRF.
! Enabling encryption on this interface requires the application of the IPsec
crypto ipsec profile DMVPN-PROFILE profile configured in the previous procedure.
set transform-set AES256/SHA/TRANSPORT interface Tunnel [number]
set isakmp-profile FVRF-ISAKMP-INET-PUBLIC tunnel source [source interface]
tunnel mode gre multipoint
tunnel vrf [vrf name]
Procedure 6 Configure the mGRE Tunnel tunnel protection ipsec profile [IPSec profile name]
Procedure Steps: Step 3: Configure NHRP.

1. Configure basic interface settings. The DMVPN hub router acts in the role of NHRP server for all of the spokes.
NHRP is used by remote routers to determine the tunnel destinations for
2. Configure the tunnel. peers attached to the mGRE tunnel.
3. Configure NHRP. NHRP requires all devices within a DMVPN cloud to use the same network
4. Configure EIGRP. ID and authentication key. The NHRP cache holdtime should be configured
to 600 seconds.
EIGRP (configured in the following procedure) relies on a multicast transport,
and requires NHRP to automatically add routers to the multicast NHRP
mappings.

The ip nhrp redirect command allows the DMVPN hub to notify spoke rout-
ers that a more optimal path may exist to a destination network, which may Procedure 7 Configure EIGRP
be required for DMVPN spoke-spoke direct communications.
Two EIGRP processes are used on the DMVPN hub routers. The primary reason
ip nhrp authentication [password]
ip nhrp map multicast dynamic for the additional process is to ensure that routes learned from the WAN
ip nhrp network-id [network id] remotes appear as EIGRP external routes on the WAN distribution switch. If
ip nhrp holdtime 600 only a single process was used, then the remote-site routes would appear
ip nhrp redirect as EIGRP internal routes on the WAN distribution switch, which would be
preferred to the MPLS VPN learned routes.
Step 4: Configure EIGRP. Procedure Steps:
EIGRP is configured in the following Procedure 9, but has some specific 1. Enable EIGRP-100 for internal routing.
requirements for the mGRE tunnel interface.
2. Enable an additional EIGRP-200 process for DMVPN.
Spoke-to-spoke DMVPN networks present a unique challenge because
the spokes cannot directly exchange information with one another, even
though they are on the same logical network. This limitation requires that the Step 1: Enable EIGRP-100 for internal routing.
DMVPN hub router advertise routes from other spokes on the same network. EIGRP-100 is configured facing the LAN distribution/core. Routes from the
This advertisement of these routes would normally be prevented by split other EIGRP process are redistributed. Because the routing protocol is the
horizon, and can be overridden by the no ip split-horizon eigrp command. same, no default metric is required.
The EIGRP hold time is increased to 35 seconds to accommodate up to 500 In this design, the port-channel interface and the loopback are EIGRP
remote sites on a single DMVPN cloud. interfaces. The loopback may remain a passive interface. The network range
interface Tunnel [number] must include both interface IP addresses either in a single network state-
ip hold-time eigrp [as number – eigrp dmvpn] 35 ment or in multiple network statements. This design uses a best practice
no ip split-horizon eigrp 200
of assigning the router ID to a loopback address. The tunnel interface
address should not be included in the network range. It may be helpful to
Procedure 6 Example explicitly list all of the relevant networks rather than include them in a single
interface Tunnel10 statement.
bandwidth 10000
ip address 10.4.132.1 255.255.254.0 router eigrp [as number]
no ip redirects network [port-channel network] [inverse mask]
ip mtu 1400 network [loopback network] 0.0.0.0
ip hold-time eigrp 200 35 redistribute eigrp [as number (DMVPN)]
ip nhrp authentication cisco123 passive-interface default
ip nhrp map multicast dynamic no passive-interface [port-channel interface]
ip nhrp network-id 101 eigrp router-id [IP address of Loopback0]
ip nhrp holdtime 600
ip nhrp redirect no auto-summary
ip tcp adjust-mss 1360
no ip split-horizon eigrp 200
tunnel source GigabitEthernet0/0/3
tunnel vrf INET-PUBLIC
tunnel protection ipsec profile DMVPN-PROFILE

Step 2: Enable an additional EIGRP-200 process for DMVPN. Step 1: Enable IP multicast routing.
EIGRP-200 is configured for the DMVPN mGRE interface. Routes from the Enable IP multicast routing on the platforms in the global configuration
other EIGRP process are redistributed. Because the routing protocol is the mode.
same, no default metric is required. ip multicast-routing
The tunnel interface is the only EIGRP interface, and its network range
should be explicitly listed. The Cisco ASR1000 Series router requires the distributed keyword
router eigrp [as number (DMVPN)] ip multicast-routing distributed
network [mGRE tunnel network] [inverse mask]
redistribute eigrp [as number] Step 2: Configure PIM, RP and scoping.
no passive-interface [mGRE tunnel interface] Every Layer 3 switch and router must be configured with the address of
eigrp router-id [IP address of Loopback0] the IP multicast RP. Use the rp-address command in conjunction with
no auto-summary an access-list to limit the network size that the RP is responsible for. This
Procedure 7 Example configuration provides for future scaling and control of the IP multicast
router eigrp 100 environment and can change based on network needs and design. The PIM
network 10.4.128.16 0.0.0.3 source is configured to be the device loopback for resiliency at sites with
network 10.4.128.243 0.0.0.0 multiple WAN transports.
redistribute eigrp 200 ip pim rp-address [IP address of RP] [ACL number]
passive-interface default ip pim register-source Loopback0
no passive-interface Port-channel3 access-list [ACL number] permit [multicast group scope] [inverse
no auto-summary mask]
router eigrp 200 All Layer 3 interfaces in the network must be enabled for sparse mode
network 10.4.132.0 0.0.1.255
passive-interface default NOTE: Do not enable PIM on the Internet DMZ interface, as no multicast traf-
no passive-interface Tunnel10 fic should be requested from this interface.
no auto-summary
ip pim sparse-mode
Procedure 8 Configure IP Multicast Routing
This procedure applies to all DMVPN Hub routers.

Procedure Steps:
2. C onfigure PIM, RP and scoping.
3. E
nable PIM non-broadcast multiple access (NBMA) mode for the
DMVPN tunnel

Step 3: Enable PIM non-broadcast multiple access (NBMA) mode for the
DMVPN tunnel. Process
Spoke-to-spoke DMVPN networks present a unique challenge because the
spokes cannot directly exchange information with one another, even though
they are on the same logical network. This inability to directly exchange WAN Distribution Switch Configuration
information can also cause problems when running IP multicast.
1. Finish Switch Universal Configuration
To resolve this issue requires a method where each remote PIM neighbor 2. C onnect to DMVPN Hub Router
has its join messages tracked separately. A router in PIM NBMA mode treats
each remote PIM neighbor as if it were connected to the router through a 3. C onnect to Core
point-to-point link. 4. C onfigure EIGRP
ip pim nbma-mode 5. C onfigure IP Multicast Routing
Procedure 8 Example
!
interface Loopback0 Procedure 1 Finish Switch Universal Configuration
ip pim sparse-mode
!
interface Port-Channel3 This guide assumes that the WAN distribution switch has already been
ip pim sparse-mode configured. Only the procedures required to complete the connections of
! the DMVPN hub router and core devices are included. Full details on distri-
interface Tunnel10 bution layer switch configuration are included in the Cisco SBA for Large
ip pim nbma-mode
Agencies—Borderless Networks LAN Deployment Guide.
ip pim sparse-mode
!
ip pim register-source Loopback0 Procedure 2 Connect to DMVPN Hub Router
The port-channel interface connects to a DMVPN hub router. This con-
nection is a Layer 3 port-channel. The following configuration creates an
EtherChannel link between the switch and router, with two channel-group
members.
Procedure Steps:
1. C onfigure the port-channel interface and assign the IP address.
2. A
dministratively enable the port-channel group members and assign

Step 1: Configure the port-channel interface and assign the IP address. are used. The core consists of two devices. The single link to each core
device provides sufficient resiliency such that EtherChannel links are not
required. The interfaces are configured as Layer 3 links.
link where possible.
interface Port-channel [number] The WAN switch generates IP route summaries for the WAN-aggregation
no switchport block and for the remote sites. After the summaries have been configured,
ip address [IP address] [netmask] EIGRP suppresses the advertisement of more specific routes within the
summary ranges.
Step 2: Enable the port-channel group members and assign the appropriate interface [interface type] [number]
channel group. no switchport
Not all router platforms can support LACP to negotiate with the switch, so ip summary-address eigrp [as number] [summary network] [summary
EtherChannel is configured statically. mask]
interface [interface type] [number] ip summary-address eigrp [as number] [summary network] [summary
no switchport mask]
no ip address
channel-group [number] mode on Procedure 3 Example
no shutdown
interface TenGigabitEthernet1/0/1
description Link to core (1)
Procedure 2 Example no switchport
interface Port-channel3 ip address 10.4.60.42 255.255.255.252
description bn-dmvpn-1 EtherChannel ip summary-address eigrp 100 10.4.128.0 255.255.192.0
no switchport ip summary-address eigrp 100 10.5.0.0 255.255.0.0
ip address 10.4.128.17 255.255.255.252
! Procedure 4 Configure EIGRP
description bn-dmvpn-1 port 1
no switchport Enable EIGRP for the IP address space that the network will be using.
no ip address If needed for your network, you can enter multiple network statements.
channel-group 3 mode on Disable auto summarization of the IP networks and enable all routed links
no shutdown to be passive by default. The Loopback 0 IP address is used for the EIGRP
! router ID to ensure maximum resiliency.
description bn-dmvpn-1 port 2 The single logical distribution layer design uses stateful switchover and
no switchport nonstop forwarding to provide sub-second failover in the event of a supervi-
no ip address sor data or control plane failure. This ability reduces packet loss in switcho-
channel-group 3 mode on ver to redundant logic and keeps packets flowing when the data plane is
no shutdown still intact to adjacent nodes. In the stack-based distribution layer approach,
a single logical control point still exists and the master control plane in a
stack can failover to another member in the stack providing near-second or
Procedure 3 Connect to Core sub-second resiliency.
This procedure is only required when the WAN deployment uses a separate
dedicated WAN distribution switch. High-performance 10-Gbps interfaces

When the supervisor or master switch of a distribution platform switches Procedure Steps:
IP data traffic flows in hardware. However, the supervisor requires time to
reestablish control plane two-way peering with EIGRP routing neighbors and 2. Configure PIM, RP and scoping.
avoid the peer router from tearing down adjacencies due to missed hellos
Step 1: Enable IP multicast routing.
the supervisor to recover, there is a Nonstop Forwarding (NSF) setting for
the routing protocol to wait for the dual supervisor peer switch to recover. Enable IP multicast routing on the platforms in the global configuration
The neighboring router is said to be NSF aware if it has a release of IOS that mode.
recognizes an NSF peer. All of the platforms used in this design are NSF ip multicast-routing
aware for the routing protocols in use.
The distribution layer switch must be configured to enable Nonstop The Cisco Catalyst 3750 Series Switch requires the distributed keyword
Forwarding for the protocol in use so that it can signal a peer when it ip multicast-routing distributed
switches over to a Hot-Standby supervisor for the peering neighbor to allow
it time to reestablish EIGRP protocol to that node. No tuning of the default Step 2: Configure PIM, RP and scoping.
NSF timers is needed in this network. Nothing has to be configured for an
NSF aware peer router.
list to limit the network size that the RP is responsible for. This configuration
passive-interface default provides for future scaling and control of the IP multicast environment and
no passive-interface [interface] can change based on network needs and design. The PIM source is
eigrp router-id [IP address of Loopback0] configured to be the device loopback for resiliency at sites with multiple
no auto-summary WAN transports.
nsf ip pim rp-address [IP address of RP] [ACL number]
Procedure 4 Example access-list [ACL number] permit [multicast group scope] [inverse
mask]
router eigrp 100
network 10.4.0.0 0.0.255.255
passive-interface default All Layer 3 interfaces in the network must be enabled for sparse mode
no passive-interface TenGigabitEthernet1/0/1 multicast operation.
no passive-interface TenGigabitEthernet2/0/1 interface [interface type] [number]
no passive-interface Port-channel3 ip pim sparse-mode
no auto-summary
nsf Procedure 5 Example
!
interface Loopback0
Procedure 5 Configure IP Multicast Routing
ip pim sparse-mode
!
This procedure applies to all WAN routers and distribution-layer LAN interface Port-Channel1
switches. ip pim sparse-mode
!
ip pim sparse-mode

! 4. On the DMZ switch, configure the interface and assign the access
interface TenGigabitEthernet1/0/1 port VLAN.
ip pim sparse-mode
!
ip pim rp-address 10.4.60.252 10 Step 1: Configure the Cisco ASA 5500 physical interface.
access-list 10 permit 239.1.0.0 0.0.255.255 Configure the interface that carries the VLAN trunk for the various DMZs.
Values are not assigned for the interface name, security level, or IP address
on trunk interfaces. Configuration details are shown in Figure 23.
Process Figure 23. Define DMZ Trunk Interface
Firewall and DMZ Switch Configuration

1. Configure Firewall DMZ
2. Configure Firewall Address Translation
3. Configure Firewall Policy for DMVPN Hub
Procedure 1 Configure Firewall DMZ
The firewall’s DMZ is a portion of the network where, typically, traffic to and
from other parts of the network is tightly restricted. Agencies place network
services in a DMZ for exposure to the Internet; these servers are typically
not allowed to initiate connections to the internal network, except for specific
circumstances.
The various DMZ networks are connected using a VLAN trunk to the Gigabit
Ethernet interface of the Cisco ASA 5500. The DMVPN hub router connects
to the DMZ switch using a single interface; the VPN-DMZ VLAN interface on
the firewall is assigned an IP address, which is the default gateway for the interface GigabitEthernet0/1
VPN-DMZ network. The VLAN interface of the DMZ switch does not have an description dmz trunk to dmz-3750 stack port x/0/1
IP address assigned for the VPN-DMZ VLAN. no nameif
no security-level
Procedure Steps: no ip address
1. Configure the Cisco ASA5500 physical interface.
Step 2: Configure the subinterface for the DMZ-VPN.
2. Configure the subinterface for the DMZ-VPN.
The DMZ VLAN interface must be configured with an appropriate IP address
3. On the DMZ switch, define the switch ports that connect to the firewall
for the attached network, as well as an intuitive interface name to be used
as trunk ports and add the appropriate VLAN.
for NAT and security policy configuration. The tested design uses the values

shown in Table 12. The configuration for a VLAN interface is illustrated in switchport trunk encapsulation dot1q
switchport trunk allowed VLAN 1128
Table 12. VPN-DMZ Configuration Parameters switchport mode trunk
spanning-tree link-type point-to-point
IP Address Security
Interface Label & Netmask VLAN Level Name If this is an additional VLAN being added to an existing trunk from the DMZ
GigabitEthernet 0/1.1128 10.4.128.35 1128 75 dmz-vpn switch, then use the following set of commands:
255.255.255.248 interface GigabitEthernet1/0/1
switchport trunk allowed VLAN add 1128
Figure 24. DMZ Subinterface Configuration Step 4: On the DMZ switch, configure the interface and assign the access
port VLAN.
switchport access VLAN [VLAN number]
no shutdown
Procedure 2 Configure Firewall Address Translation
Prior to this procedure, the DMZ-VPN network would have connectivity to the
Cisco ASA 5500 interface, but there would be no access from the DMZ-VPN
network to the Internet, or from the Internet to the DMZ-VPN. A last step is
required to allow Internet connectivity for the DMZ; the DMZ network uses
private network (RFC 1918) addressing that is not Internet routable, so the
firewall must translate the DMZ address to an outside public address. For
this configuration, we are going to translate the DMZ-VPN address of the
DMVPN hub router to a public IP address that can be routed on the Internet
as shown in Table 13.
Table 13. DMVPN Hub IP Address Translation Information
DMVPN Hub Public DMVPN Hub Public Address

interface GigabitEthernet0/1.1128 Address (actual) (externally routable after NAT)
VLAN 1128
nameif dmz-vpn 10.4.128.133 172.16.130.1
security-level 75
ip address 10.4.128.35 255.255.255.248 NOTE: As you apply the address translation configuration described in this
portion of the document, the security appliance applies its default access
Step 3: On the DMZ switch, define the switch ports that connect to the rule set that permits traffic from higher-security interfaces to lower-security
firewall as trunk ports and add the appropriate VLAN. interfaces. Review your expected traffic carefully; if you cannot allow some
If this is the first VLAN to be added to the trunk from the DMZ switch, then or all traffic that is allowed by the default rules, you should shut down the
use the following set of commands: various device interfaces until you have completely configured your firewall
interface GigabitEthernet1/0/1 rule set.
description ASA5540-1 DMZ uplink

Procedure Steps: Figure 26. Define Firewall Static Translations for DMVPN Hub Router
1. Configure name-to-address mappings for DMZ-VPN network and the
DMVPN hub router.
2. Define static translation policy for traffic passing between the Internet
and the DMVPN hub router in the DMZ-VPN.
Step 1: Configure name-to-address mappings for DMZ-VPN network and

the DMVPN hub router.
These names are used for NAT configuration, as well as access-rule defini-
tion. Be sure the names that you apply are applicable for all parts of the
configuration. Using address-family names and object-groups improves
command-line and Cisco Adaptive Security Device Manager (ASDM) static (dmz-vpn,outside) 172.16.130.1 10.4.128.33 netmask
usability for the Cisco ASA 5500, as the various IP networks and hosts within 255.255.255.255
your agency are represented as names instead of IP addresses. This step is
shown in Figure 25.
Procedure 3 Configure Firewall Policy for DMVPN Hub
Go to Configuration > Firewall > Objects > Network Objects/Groups
Security policy configuration is fairly arbitrary to suit the policy and manage-
Figure 25. Configure Network Object Names ment requirements of an agency. Thus, examples here should be used as a
basis for your network-security requirements.
The Site-to-Site VPN DMZ provides an additional layer of protection to lower
the likelihood of certain types of misconfiguration of the VPN routers expos-
ing the agency network to the Internet. A filter allows only VPN traffic as well
as some diagnostic traffic to reach the VPN routers, to facilitate trouble-
shooting for reachability to the VPN hubs from remote sites.
Table 14. Required DMVPN Protocols (Hub Router)
Name Protocol Usage
non500-isakmp UDP 4500 IPsec via NAT-T
isakmp UDP 500 ISAKMP
names esp IP 50 IPsec
name 172.16.130.1 outside-dmvpn-1
name 10.4.128.32 dmz-dmvpn
name 10.4.128.33 dmz-dmvpn-1
Step 2: Define static translation policy for traffic passing between the
Internet and the DMVPN hub router in the DMZ-VPN.
All devices that must be exposed to the Internet require a static translation.
The DMVPN hub router translation is shown in Figure 26.

Table 15. Optional Protocols—DMVPN Hub Router Step 2: This step is optional. Define additional access-control entries to
allow diagnostic traffic to the DMVPN routers in the DMZ-VPN.
Name Protocol Usage
This policy is applied on the outside-interface access rule, and builds on
icmp echo ICMP Type 0, Code 0 Allow remote pings existing policies:
access-list OUT-ACCESS-IN extended permit icmp any host
icmp echo-reply ICMP Type 8, Code 0 Allow ping replies
outside-dmvpn-1 echo
(from our requests) access-list OUT-ACCESS-IN extended permit icmp any host
icmp ttl-exceeded ICMP Type 11, Code 0 Allow traceroute replies outside-dmvpn-1 echo-reply
access-group OUT-ACCESS-IN in interface outside-16
(from our requests)
The combined policy as implemented in Step 1 and Step 2 is illustrated in
icmp ICMP Type 3, Code 3 Allow traceroute replies Figure 27.
port-unreachable (from our requests)
UDP high ports UDP > 1023 Allow remote traceroute Figure 27. Define Internet to DMZ-VPN Inbound Policy
Procedure Steps:
1. Define access-control entries to allow VPN traffic to the DMVPN rout-
ers in the DMZ-VPN.
2. Define additional access-control entries to allow diagnostic traffic to
the DMVPN routers in the DMZ-VPN.
Step 1: Define access-control entries to allow VPN and diagnostic traffic

to the DMVPN routers in the DMZ-VPN.
This policy is applied on the outside-interface Access Rule, and builds on
existing policies:
access-list OUT-ACCESS-IN extended permit udp any host outside-
dmvpn-1 eq 4500
access-list OUT-ACCESS-IN extended permit udp any host outside-
dmvpn-1 eq isakmp
access-list OUT-ACCESS-IN extended permit esp any host outside-
dmvpn-1
access-group OUT-ACCESS-IN in interface outside-16

Figure 28. Adding DMVPN Backup Configuration Flowchart
Process
Enabling DMVPN Backup on Existing MPLS CE

Router Configuration
2. Connect to the Internet
5. Configure EIGRP
This set of procedures includes the additional steps necessary to complete

the configuration of a dual-role MPLS CE and DMVPN spoke router for a
MPLS WAN + DMVPN remote site (single-router, dual-link).
The following procedures assume that the configuration of a MPLS CE
Router for a MPLS WAN remote site (single-router, single-link) has already
been completed. Only the additional procedures to add the DMVPN backup
to the running MPLS CE router are included here. Procedure 1 Configure VRF Lite
The flowchart in Figure 28 provides details on how to add DMVPN backup
on an existing remote-site MPLS CE router. An Internet-facing VRF is created to support Front Door VRF for DMVPN.
The VRF name is arbitrary, but it is useful to select a name that describes
make the VRF functional. The RD configuration also creates the routing and
forwarding tables and associates the RD with the VRF instance.
This design uses VRF Lite so the RD value can be chosen arbitrarily. It is a
best practice to use the same VRF/RD combination across multiple devices
when using VRFs in a similar manner. However, this convention is not
strictly required.
Command Reference:
An RD is either of the following:
• ASN-related—Composed of an ASN and an arbitrary number.
• I P-address-related—Composed of an IP address and an
arbitrary number.
You can enter an RD in either of these formats:

16-bit autonomous-system-number: your 32-bit number Table 16. Required DMVPN Protocols
For example, 65512:1 Name Protocol Usage
32-bit IP address: your 16-bit number non500-isakmp UDP 4500 IPsec via NAT-T
For example, 192.168.122.15:1. isakmp UDP 500 ISAKMP
ip vrf [vrf-name] esp IP 50 IPsec
rd [ASN:number] bootpc UDP 68 DHCP
Procedure 1 Example
Example access list:
ip vrf INET-PUBLIC
rd 65512:1 interface [interface type] [number]
ip access-group [ACL name] in
ip access-list extended [ACL name]
permit udp any any eq non500-isakmp
Procedure 2 Connect to the Internet permit udp any any eq isakmp
permit esp any any
The remote sites using DMVPN can use either static or dynamically assigned permit udp any any eq bootpc
IP addresses. We tested the design with a DHCP assigned external address,
which also provides a dynamically configured default route. The additional protocols listed in Table 17 may assist in troubleshooting, but
are not explicitly required to allow DMVPN to function properly.
The DMVPN spoke router connects directly to the Internet without a separate
firewall. This connection is secured in two ways. Since the Internet interface Table 17. Optional Protocols - DMVPN Spoke Router
is in a separate VRF, no traffic can access the global VRF except traffic
sourced through the DMVPN tunnel. This design provides implicit security. Name Protocol Usage
Additionally, an IP access list permits only the traffic required for an encrypted icmp echo ICMP Type 0, Code 0 Allow remote pings
tunnel, as well as DHCP and various ICMP protocols for troubleshooting. icmp echo-reply ICMP Type 8, Code 0 Allow ping replies
Procedure Steps: (from our requests)
icmp ttl-exceeded ICMP Type 11, Code 0 Allow traceroute replies
1. Administratively enable the interface, select VRF and enable DHCP. (from our requests)
2. Configure and apply the access list. icmp port-unreachable ICMP Type 3, Code 3 Allow traceroute replies
(from our requests)
Step 1: Enable the interface, select VRF and enable DHCP. UDP high ports UDP > 1023, TTL=1 Allow remote traceroute
The DMVPN design uses Front Door VRF, so this interface must be placed
into the VRF configured in the previous procedure. The additional optional entries for an access list to support ping are as follows:
interface [interface type] [number] permit icmp any any echo
ip vrf forwarding [vrf name] permit icmp any any echo-reply
ip address dhcp
no shutdown The additional optional entries for an access list to support traceroute are as follows:
permit icmp any any ttl-exceeded ! for traceroute
Step 2: Configure and apply the access list. (sourced)
permit icmp any any port-unreachable ! for traceroute
The IP access list must permit the protocols specified in Table 16. The (sourced)
access list is applied inbound on the WAN interface, so filtering is done on permit udp any any gt 1023 ttl eq 1 ! for traceroute
traffic destined to the router. (destination)

Procedure 2 Example DPD is enabled with keepalives sent at 30-second intervals with a 5-second
interface GigabitEthernet0/1 retry interval, which is considered to be a reasonable setting to detect a
ip vrf forwarding INET-PUBLIC failed hub.
ip address dhcp crypto isakmp policy 10
ip access-group ACL-INET-PUBLIC in encr aes 256
no shutdown hash sha
authentication pre-share
ip access-list extended ACL-INET-PUBLIC group 2
permit udp any any eq non500-isakmp !
permit udp any any eq isakmp crypto isakmp keepalive 30 5
permit esp any any
permit icmp any any echo
permit icmp any any echo-reply Step 3: Create the ISAKMP profile.
permit udp any any eq bootpc The ISAKMP profile creates an association between an identity address, a
VRF and a crypto keyring. A wildcard address within a VRF is referenced
with 0.0.0.0.
Procedure 3 Configure ISAKMP and IPsec
crypto isakmp profile [ISAKMP profile name]
keyring [keyring name]
Procedure Steps: match identity address 0.0.0.0 [vrf name]
1. Configure the crypto keyring.
Step 4: Define the IPsec transform set.
2. Configure the ISAKMP policy and dead peer detection.
3. Create the ISAKMP profile. rithms, and other settings to apply to IPsec-protected traffic. Peers agree to
4. Define the IPsec transform set. use a particular transform set when protecting a particular data flow.
5. Create the IPsec profile. The IPsec transform set for DMVPN uses the following:
• ESP with the 256-bit AES encryption algorithm
Step 1: Configure the crypto keyring.
• ESP with the SHA (HMAC variant) authentication algorithm
The crypto keyring defines a pre-shared key (or password) valid for IP
Since the DMVPN hub router is behind a NAT device, the IPsec transform
sources reachable within a particular VRF. This key is a wildcard pre-shared
key if it applies to any IP source. A wildcard key is configured using the
0.0.0.0 0.0.0.0 network/mask combination. crypto ipsec transform-set [IPSec transform-set name] esp-aes
256 esp-sha-hmac
crypto keyring [keyring name] vrf [vrf name] mode transport
Step 5: Create the IPsec profile.

Step 2: Configure the ISAKMP Policy and Dead Peer Detection.
The IPsec profile creates an association between an ISAKMP profile and an
The ISAKMP policy for DMVPN uses the following:
IPsec transform-set.
• Advanced Encryption Standard (AES) with a 256-bit key crypto ipsec profile [IPSec profile name]
set transform-set [IPSec transform-set name]
• Secure Hash Standard (SHA) set isakmp-profile [ISAKMP profile name]
• Diffie-Hellman group: 2

Procedure 3 Example interface Tunnel [number]
crypto keyring DMVPN-KEYRING vrf INET-PUBLIC bandwidth [bandwidth (kbps)]
pre-shared-key address 0.0.0.0 0.0.0.0 key cisco123 ip address [IP address] [netmask]
no ip redirects
crypto isakmp policy 10 ip mtu 1400
encr aes 256 ip tcp adjust-mss 1360
hash sha
authentication pre-share Step 2: Configure the tunnel.
group 2
DMVPN uses multipoint GRE (mGRE) tunnels. This type of tunnel requires
crypto isakmp keepalive 30 5 a source interface only. The source interface should be the same interface
crypto isakmp profile FVRF-ISAKMP-INET-PUBLIC should be set to the VRF defined previously for Front Door VRF.
keyring DMVPN-KEYRING
match identity address 0.0.0.0 INET-PUBLIC Enabling encryption on this interface requires the application of the IPsec
profile configured in the previous procedure.
crypto ipsec transform-set AES256/SHA/TRANSPORT esp-aes 256 esp- interface Tunnel [number]
sha-hmac tunnel source [source interface]
mode transport tunnel mode gre multipoint
! tunnel vrf [vrf name]
crypto ipsec profile DMVPN-PROFILE tunnel protection ipsec profile [IPSec profile name]
set transform-set AES256/SHA/TRANSPORT
set isakmp-profile FVRF-ISAKMP-INET-PUBLIC Step 3: Configure NHRP.
The DMVPN hub router is the NHRP server for all of the spokes. NHRP
is used by remote routers to determine the tunnel destinations for peers
Procedure 4 Configure the mGRE Tunnel
attached to the mGRE tunnel.
The spoke router requires several additional configuration statements to
Procedure Steps: define the NHRP server (NHS) and NHRP map statements for the DMVPN
1. Configure basic interface settings. hub router mGRE tunnel IP address. EIGRP (configured in the following
Procedure 5) relies on a multicast transport. Spoke routers require the NHRP
2. Configure the tunnel.
static multicast mapping.
3. Configure NHRP.
The value used for the NHS is the mGRE tunnel address for the DMVPN hub
4. Configure EIGRP. router. The map entries must be set to the outside NAT value of the DMVPN
hub, as configured on the Cisco ASA5500. This design uses the values
Step 1: Configure basic interface settings. shown in Table 18.
Tunnel interfaces are created as they are configured. The tunnel number is Table 18. DMVPN Hub IP Address Information
arbitrary, but it is best to begin tunnel numbering at 10 or above, because
other features deployed in this design may also require tunnels and they DMVPN Hub Public
may select lower numbers by default. DMVPN Hub Address (exter- NHS
Public Address nally routable (DMVPN Hub mGRE
The bandwidth setting should be set to match the Internet bandwidth. (actual) after NAT) Tunnel Address)
The IP MTU should be configured to 1400 and the ip tcp adjust-mss should
be configured to 1360. There is a 40 byte difference, which corresponds to 10.4.128.133 172.16.130.1 10.4.132.1
the combined IP and TCP header length.

NHRP requires all devices within a DMVPN cloud to use the same network Procedure 4 Example
ID and authentication key. The NHRP cache holdtime should be configured interface Tunnel10
to 600 seconds. bandwidth 1500
ip address 10.4.132.205 255.255.254.0
This design supports DMVPN spoke routers that receive their external IP no ip redirects
addresses through DHCP. It is possible for these routers to acquire different IP ip mtu 1400
addresses after a reload. When the router attempts to register with the NHRP ip nhrp authentication cisco123
server, it may appear as a duplicate to an entry already in the cache and be ip nhrp map 10.4.132.1 172.16.130.1
rejected. The registration no-unique option allow existing cache entries to ip nhrp map multicast 172.16.130.1
be overwritten. This feature is only required on NHRP clients (DMVPN spoke ip nhrp network-id 101
routers). ip nhrp holdtime 600
ip nhrp nhs 10.4.132.1
The ip nhrp redirect command allows the DMVPN hub to notify spoke rout- ip nhrp registration no-unique
ers that a more optimal path may exist to a destination network, which may be ip nhrp shortcut
required for DMVPN spoke-to-spoke direct communications. DMVPN spoke ip tcp adjust-mss 1360
routers also use shortcut switching when building spoke-to-spoke tunnels. ip summary-address eigrp 200 10.5.192.0 255.255.248.0
interface Tunnel [number] tunnel source GigabitEthernet0/1
ip nhrp authentication [password] tunnel mode gre multipoint
ip nhrp map [NHS IP address] [DMVPN hub outside IP address] tunnel vrf INET-PUBLIC
ip nhrp map multicast [DMVPN hub outside IP address] tunnel protection ipsec profile DMVPN-PROFILE
ip nhrp network-id [network id]
ip nhrp nhs [NHS IP address] Procedure 5 Configure EIGRP
ip nhrp registration no-unique
ip nhrp shortcut
ip nhrp redirect A single EIGRP-200 process runs on the DMVPN spoke router. All interfaces
on the router are EIGRP interfaces, but only the DMVPN tunnel interface
Step 4: Configure EIGRP. is non-passive. The network range must include all interface IP addresses
either in a single network statement or in multiple network statements. This
The remote-site LAN networks must be advertised. The IP assignment design uses a best practice of assigning the router ID to a loopback address.
for the remote sites was designed so that all of the networks in use can router eigrp [as number (dmvpn)]
be summarized within a single aggregate route. The summary address network [mGRE tunnel network] [inverse mask]
as configured below suppresses the more specific routes. If any network network [WAN remote range] [inverse mask]
within the summary is present in the route table, the summary is advertised passive-interface default
to the DMVPN hub, which offers a measure of resiliency. If the various LAN no passive-interface [mGRE tunnel interface]
networks can not be summarized, then EIGRP continues to advertise the eigrp router-id [IP address of Loopback0]
specific routes. no auto-summary
ip summary-address eigrp [as number (dmvpn)] [summary
network] [summary mask]

Procedure 5 Example Step 2: Enable PIM non-broadcast multiple access mode for the DMVPN
router eigrp 200 tunnel.
network 10.4.132.0 0.0.1.255
network 10.5.0.0 0.0.255.255
passive-interface default spokes cannot directly exchange information with one another, even though
no passive-interface Tunnel10 they are on the same logical network. This inability to directly exchange
eigrp router-id 10.5.192.254 information can also cause problems when running IP multicast.
no auto-summary Resolving the NBMA issue requires a method where each remote PIM
neighbor has its join messages tracked separately. A router in PIM NBMA
mode treats each remote PIM neighbor as if it were connected to the router
Procedure 6 Configure IP Multicast Routing through a point-to-point link.
ip pim nbma-mode
This procedure includes additional steps for completing the IP multicast
configuration when adding DMVPN backup capability to a router with IP
Step 3: Configure the DR priority for the DMVPN spoke router.
multicast already enabled.
Proper multicast operation across a DMVPN cloud requires that the hub
Procedure Steps:
router assumes the role of PIM Designated Router (DR). Spoke routers
1. Configure PIM on the DMVPN tunnel interface. should never become the DR. You can prevent that by setting the DR priority to
2. Enable PIM non-broadcast multiple access mode for the DMVPN 0 for the spokes.
tunnel. interface Tunnel [number]
3. Configure the DR priority for the DMVPN spoke router.
Procedure 6 Example
Step 1: Configure PIM on the DMVPN tunnel interface. interface Tunnel10
We recommend using sparse-mode for IP multicast interface operation
ip pim nbma-mode
mode and to enable it on all Layer 3 interfaces, including DMVPN tunnel ip pim sparse-mode
interfaces.
NOTE: Do not enable PIM on the Internet interface, as no multicast traffic
should be requested from this interface.

ip pim sparse-mode

Figure 29. Remote-Site DMVPN Spoke Router Configuration Flowchart
Process
Remote-Site DMVPN Spoke Router Configuration

This set of procedures is for the configuration of a DMVPN spoke
router for a DMVPN remote site (single-router, single-link) and includes
all required procedures.
This set of procedures should also be used when configuring a MPLS
WAN + DMVPN remote site. Use these procedures when configuring
the second router of the dual-router, dual-link design.
The flowchart in Figure 29 provides details on how to complete the
configuration of a remote-site DMVPN spoke router.
3. Connect to the Internet
6. Configure EIGRP
Procedure 1 Finish WAN Router Universal Configuration
8. Configure Access Layer Routing
The following procedures are only relevant for the dual-router design:
Procedure Steps:
9. Configure Access Layer HSRP
1. Configure the device hostname.
10. Configure the Transit Network
2. Configure in-band management.
11. Configure EIGRP (LAN Side)
3. Configure device-management protocols.
4. Configure secure user authentication.
5. Configure a synchronized clock

a HTTP server securely. It uses SSL and TLS to provide device authentica- RADIUS server is unavailable, or if you do not have a RADIUS server in
tion and data encryption. Both protocols are encrypted for privacy and the your agency. We highly recommend the use of a centralized authentication
!
Enabling SSH requires that a public/private keypair be generated for the username admin password c1sco123
device: aaa new-model

interface. For secure access to this interface you must enable the secure NTP is designed to synchronize a network of devices. An NTP network
for allowing you to continue typing at the device console when debugging
is enabled.

ntp server 10.4.200.17
ntp source Loopback0 Procedure 3 Connect to the Internet
Series
! The remote sites using DMVPN can use either static or dynamically
clock timezone PST -8 assigned IP addresses. The design has been tested with a DHCP-assigned
clock summer-time PDT recurring external address, which also provides a dynamically configured
! default route.
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime The DMVPN spoke router connects directly to the Internet without a sepa-
rate firewall. This connection is secured in two ways. Since the Internet
interface is in a separate VRF, no traffic can access the global VRF except
traffic sourced through the DMVPN tunnel. This design provides implicit
Procedure 2 Configure VRF Lite security. Additionally, an IP access list permits only the traffic required
for an encrypted tunnel, as well as DHCP and various ICMP protocols for
troubleshooting.
An Internet-facing VRF is created to support Front Door VRF for DMVPN.
The VRF name is arbitrary, but it is useful to select a name that describes Procedure Steps:
1. Administratively enable the interface, select VRF, and enable DHCP.
make the VRF functional. The RD configuration also creates the routing and
forwarding tables and associates the RD with the VRF instance. 2. Configure and apply the access list.
This design uses VRF Lite so the RD value can be chosen arbitrarily. It is a
best practice to use the same VRF/RD combination across multiple devices Step 1: Enable the interface, select VRF, and enable DHCP.
when using VRFs in a similar manner. However, this convention is not
The DMVPN design uses Front Door VRF, so this interface must be placed
strictly required.
into the VRF configured in the previous procedure.
Command Reference: interface [interface type] [number]
ip vrf forwarding [vrf name]
An RD is either of the following: ip address dhcp
• ASN-related—Composed of an ASN and an arbitrary number. no shutdown
• I P-address-related—Composed of an IP address and an
arbitrary number. Step 2: Configure and apply the access list.
You can enter an RD in either of these formats: The IP access list must permit the protocols specified in Table 19. The
access list is applied inbound on the WAN interface, so filtering is done on
16-bit autonomous-system-number: your 32-bit number
traffic
For example, 65512:1 destined to the router.
32-bit IP address: your 16-bit number Table 19. Required DMVPN Protocols
For example, 192.168.122.15:1.
Name Protocol Usage
ip vrf [vrf-name]
rd [ASN:number] non500-isakmp UDP 4500 IPsec via NAT-T
isakmp UDP 500 ISAKMP
Procedure 2 Example esp IP 50 IPsec
ip vrf INET-PUBLIC
rd 65512:1 bootpc UDP 68 DHCP

Example access list: ip address dhcp
interface [interface type] [number] ip access-group ACL-INET-PUBLIC in
ip access-group [ACL name] in no shutdown
ip access-list extended [ACL name]
permit udp any any eq non500-isakmp ip access-list extended ACL-INET-PUBLIC
permit udp any any eq isakmp permit udp any any eq non500-isakmp
permit esp any any permit udp any any eq isakmp
permit udp any any eq bootpc permit esp any any
permit icmp any any echo
permit icmp any any echo-reply
The additional protocols listed in Table 20 may assist in troubleshooting, but permit udp any any eq bootpc
are not explicitly required to allow DMVPN to function properly.
Table 20. Optional Protocols—DMVPN Spoke Router
Procedure 4 Configure ISAKMP and IPsec
Name Protocol Usage
icmp echo ICMP Type 0, Code 0 Allow remote pings Procedure Steps:
icmp echo-reply ICMP Type 8, Code 0 Allow ping replies 1. Configure the crypto keyring.
(from our requests)
2. Configure the ISAKMP policy and dead peer detection.
icmp ttl-exceeded ICMP Type 11, Code 0 Allow traceroute replies
(from our requests) 3. Create the ISAKMP profile.
icmp port-unreachable ICMP Type 3, Code 3 Allow traceroute replies 4. Define the IPsec transform set.
(from our requests) 5. Create the IPsec profile.
UDP high ports UDP > 1023, TTL=1 Allow remote
traceroute Step 1: Configure the crypto keyring.
The crypto keyring defines a pre-shared key (or password) valid for IP
The additional optional entries for an access list to support ping are as sources reachable within a particular VRF. This key is a wildcard pre-shared
follows: key if it applies to any IP source. A wildcard key is configured using the
permit icmp any any echo 0.0.0.0 0.0.0.0 network/mask combination.
permit icmp any any echo-reply crypto keyring [keyring name] vrf [vrf name]
The additional optional entries for an access list to support traceroute are as
follows: Step 2: Configure the ISAKMP policy and dead peer detection.
permit icmp any any ttl-exceeded ! for traceroute
(sourced) The ISAKMP policy for DMVPN uses the following:
permit icmp any any port-unreachable ! for traceroute • Advanced Encryption Standard (AES) with a 256-bit key
(sourced)
permit udp any any gt 1023 ttl eq 1 ! for traceroute • Secure Hash Standard (SHA)
(destination)
Procedure 3 Example • Diffie-Hellman group: 2

ip vrf forwarding INET-PUBLIC

DPD is enabled with keepalives sent at 30-second intervals with a 5-second Procedure 4 Example
retry interval, which is considered to be a reasonable setting to detect a crypto keyring DMVPN-KEYRING vrf INET-PUBLIC
failed hub. pre-shared-key address 0.0.0.0 0.0.0.0 key cisco123
crypto isakmp policy 10
encr aes 256 crypto isakmp policy 10
hash sha encr aes 256
authentication pre-share hash sha
group 2 authentication pre-share
! group 2
crypto isakmp keepalive 30 5
crypto isakmp keepalive 30 5
crypto isakmp profile FVRF-ISAKMP-INET-PUBLIC
Step 3: Create the ISAKMP profile. keyring DMVPN-KEYRING
The ISAKMP profile creates an association between an identity address, a match identity address 0.0.0.0 INET-PUBLIC
VRF and a crypto keyring. A wildcard address within a VRF is referenced
crypto ipsec transform-set AES256/SHA/TRANSPORT esp-aes 256 esp-
with 0.0.0.0.
sha-hmac
crypto isakmp profile [ISAKMP profile name] mode transport
keyring [keyring name] !
match identity address 0.0.0.0 [vrf name] crypto ipsec profile DMVPN-PROFILE
set transform-set AES256/SHA/TRANSPORT
Step 4: Define the IPsec transform set set isakmp-profile FVRF-ISAKMP-INET-PUBLIC
rithms, and other settings to apply to IPsec-protected traffic. Peers agree to Procedure 5 Configure the mGRE Tunnel
use a particular transform set when protecting a particular data flow.
The IPsec transform set for DMVPN uses the following: Procedure Steps:
• ESP with the 256-bit AES encryption algorithm 1. Configure basic interface settings.
• ESP with the SHA (HMAC variant) authentication algorithm 2. Configure the tunnel.
Since the DMVPN hub router is behind a NAT device, the IPsec transform 3. Configure NHRP.
4. Configure EIGRP.
crypto ipsec transform-set [IPSec transform-set name] esp-aes
256 esp-sha-hmac
mode transport Step 1: Configure basic interface settings.
Tunnel interfaces are created as they are configured. The tunnel number is
Step 5: Create the IPsec profile. arbitrary, but it is best to begin tunnel numbering at 10 or above, because
The IPsec profile creates an association between an ISAKMP profile and an other features deployed in this design may also require tunnels and they
IPsec transform-set. may select lower numbers by default.
crypto ipsec profile [IPSec profile name] The bandwidth setting should be set to match the Internet bandwidth.
set transform-set [IPSec transform-set name]
set isakmp-profile [ISAKMP profile name] The IP MTU should be configured to 1400 and the ip tcp adjust-mss should
be configured to 1360. There is a 40 byte difference which corresponds to
the combined IP and TCP header length.

interface Tunnel [number] NHRP requires all devices within a DMVPN cloud to use the same network
bandwidth [bandwidth (kbps)] ID and authentication key. The NHRP cache holdtime should be configured
ip address [IP address] [netmask] to 600 seconds.
no ip redirects
ip mtu 1400 This design supports DMVPN spoke routers that receive their external IP
ip tcp adjust-mss 1360 addresses through DHCP. It is possible for these routers to acquire different
IP addresses after a reload. When the router attempts to register with the
Step 2: Configure the tunnel. NHRP server, it may appear as a duplicate to an entry already in the cache
and be rejected. The registration no-unique option allows existing cache
DMVPN uses multipoint GRE (mGRE) tunnels. This type of tunnel requires entries to be overwritten. This feature is only required on NHRP clients
a source interface only. The source interface should be the same interface (DMVPN spoke routers).
should be set to the VRF defined previously for Front Door VRF. The ip nhrp redirect command allows the DMVPN hub to notify spoke routers
that a more optimal path may exist to a destination network, which may be
Enabling encryption on this interface requires the application of the IPsec required for DMVPN spoke-to-spoke direct communications. DMVPN spoke
profile configured in the previous procedure. routers also use shortcut switching when building spoke-to-spoke tunnels.
interface Tunnel [number] interface Tunnel [number]
tunnel source [source interface] ip nhrp authentication [password]
tunnel mode gre multipoint ip nhrp map [NHS IP address] [DMVPN hub outside IP address]
tunnel vrf [vrf name] ip nhrp map multicast [DMVPN hub outside IP address]
tunnel protection ipsec profile [IPSec profile name] ip nhrp network-id [network id]
Step 3: Configure NHRP. ip nhrp nhs [NHS IP address]
The DMVPN hub router is the NHRP server for all of the spokes. ip nhrp shortcut
NHRP is used by remote routers to determine the tunnel destinations for ip nhrp redirect
peers attached to the mGRE tunnel.
Step 4: Configure EIGRP.
The spoke router requires several additional configuration statements to
define the NHRP server (NHS) and NHRP map statements for the DMVPN The remote-site LAN networks must be advertised. The IP assignment
hub router mGRE tunnel IP address. EIGRP (configured in the following for the remote sites was designed so that all of the networks in use can
Procedure 6) relies on a multicast transport. Spoke routers require the NHRP be summarized within a single aggregate route. The summary address
static multicast mapping. as configured below suppresses the more specific routes. If any network
within the summary is present in the route table, the summary is advertised
The value used for the NHS is the mGRE tunnel address for the DMVPN hub to the DMVPN hub, which offers a measure of resiliency. If the various LAN
router. The map entries must be set to the outside NAT value of the DMVPN networks can not be summarized, then EIGRP continues to advertise the
hub, as configured on the Cisco ASA5500. This design uses the values specific routes
shown in Table 21.
Table 21. DMVPN Hub IP Address Information ip summary-address eigrp [as number (dmvpn)] [summary
network] [summary mask]
DMVPN Hub Public
DMVPN Hub Address (exter- NHS Procedure 5 Example
Public Address nally routable (DMVPN Hub mGRE interface Tunnel10
(actual) after NAT) Tunnel Address) bandwidth 1500
10.4.128.133 172.16.130.1 10.4.132.1 ip address 10.4.132.203 255.255.254.0

no ip redirects
ip mtu 1400 Procedure 7 Configure IP Multicast Routing
ip nhrp authentication cisco123
ip nhrp map 10.4.132.1 172.16.130.1
ip nhrp map multicast 172.16.130.1 This procedure applies to all DMVPN spoke routers.
ip nhrp network-id 101
ip nhrp holdtime 600 Procedure Steps:
ip nhrp nhs 10.4.132.1 1. Enable IP multicast routing.
ip nhrp shortcut 2. Configure PIM, RP and scoping.
ip tcp adjust-mss 1360 3. Enable PIM non-broadcast multiple access mode for DMVPN tunnel.
tunnel source GigabitEthernet0/0 4. Configure the DR priority for the DMVPN spoke router.
tunnel vrf INET-PUBLIC
tunnel protection ipsec profile DMVPN-PROFILE Step 1: Enable IP multicast routing.
mode.
Procedure 6 Configure EIGRP ip multicast-routing
A single EIGRP process is run on the DMVPN spoke router. All interfaces on Step 2: Configure PIM, RP and scoping.
the router are EIGRP interfaces, but only the DMVPN tunnel interface is non-
passive. The network range must include all interface IP addresses either in
a single network statement or in multiple network statements. This design
list to limit the network size that the RP is responsible for. This configuration
uses a best practice of assigning the router ID to a loopback address. provides for future scaling and control of the IP multicast environment and
router eigrp [as number (dmvpn)] can change based on network needs and design. The PIM source is con-
network [mGRE tunnel network] [inverse mask] figured to be the device loopback for resiliency at sites with multiple WAN
network [WAN remote range] [inverse mask] transports.
no passive-interface [mGRE tunnel interface] ip pim rp-address [IP address of RP] [ACL number]
eigrp router-id [IP address of Loopback0] ip pim register-source Loopback0
no auto-summary access-list [ACL number] permit [multicast group scope] [inverse
mask]
Procedure 6 Example
router eigrp 200 multicast operation.
network 10.4.132.0 0.0.1.255
network 10.5.0.0 0.0.255.255 NOTE: Do not enable PIM on the Internet interface, as no multicast traffic
passive-interface default should be requested from this interface.
no passive-interface Tunnel10
eigrp router-id 10.5.48.253 interface [interface type] [number]
no auto-summary ip pim sparse-mode
Step 3: Enable PIM non-broadcast multiple access mode for the

DMVPN tunnel.

spokes cannot directly exchange information with one another, even though Procedure 8 Configure Access Layer Routing
they are on the same logical network. This inability to directly exchange
information can also cause problems when running IP multicast.
Procedure Steps:
Resolving the NBMA issue requires a method where each remote PIM
neighbor has its join messages tracked separately. A router in PIM NBMA 1. Enable the physical interface.
mode treats each remote PIM neighbor as if it were connected to the router 2. Create subinterfaces and assign VLAN tags.
through a point-to-point link.
3. Configure IP settings for each subinterface.
ip pim nbma-mode
In the access-layer design, the remote sites use collapsed routing, with
Step 4: Configure the DR priority for the DMVPN spoke router. 802.1Q trunk interfaces to the LAN access layer. The VLAN numbering is
locally significant only. The access switches are Layer 2 only.
Proper multicast operation across a DMVPN cloud requires that the hub router
assumes the role of PIM Designated Router (DR). Spoke routers should never Step 1: Enable the physical interface.
become the DR. This can be prevented by setting the DR priority to 0 for the interface [interface type] [number]
spokes. no ip address
interface Tunnel [number] no shutdown
Procedure 7 Example Step 2: Create subinterfaces and assign VLAN tags.
ip multicast-routing After the physical interface has been enabled, then the appropriate data or
! voice subinterfaces can be mapped to the VLANs on the LAN switch. The
interface Loopback0 subinterface number does not need to equate to the 802.1Q tag, but making
ip pim sparse-mode
them the same simplifies the overall configuration. The subinterface portion
!
interface GigabitEthernet0/2.64 of the configuration should be repeated for all data or voice VLANs.
ip pim sparse-mode interface [interface type] [number].[sub-interface number]
! encapsulation dot1Q [dot1q VLAN tag]
interface Tunnel10
ip pim dr-priority 0 Step 3: Configure IP settings for each subinterface.
ip pim nbma-mode
ip pim sparse-mode This design uses an IP addressing convention with the default gateway
! router assigned an IP address and IP mask combination of N.N.N.1
ip pim rp-address 10.4.60.252 10 255.255.255.0 where N.N.N is the IP network and 1 is the IP host.
access-list 10 permit 239.1.0.0 0.0.255.255 All router LAN interfaces that use DHCP for end-station IP assignment must
use an IP helper to reach a centralized DHCP server in this design.
If the Remote-site DMVPN spoke router is the second router of a dual-router
design, then HSRP is configured at the access layer. This requires a modi-
fied IP configuration on each subinterface. For the modified procedure, you
should skip to Procedure 9 after completing Steps 1 and 2.
ip address [LAN network 1] LAN network 1 netmask]

ip helper-address [IP address of DHCP server] The following procedures (9–11) are only relevant for the
dual-router design.
Procedure 8 Example
interface GigabitEthernet0/2 Procedure 9 Configure Access Layer HSRP
no ip address
no shutdown
! HSRP is configured to enable the use of a VIP to be used as a default gateway
! that is shared between two routers. The HSRP active router is the MPLS CE
interface GigabitEthernet0/2.64 router and the HSRP standby router is the DMVPN spoke router. Configure the
description Data DMVPN spoke router with a standby priority that is less than the MPLS
encapsulation dot1Q 64 CE router.
ip address 10.5.52.1 255.255.255.0
ip helper-address 10.4.200.10 The router with the higher standby priority value is elected as the HSRP
ip pim sparse-mode active router. The preempt option allows a router with a higher priority to
! become the HSRP active router, without waiting for a scenario where there
interface GigabitEthernet0/2.65 is no router in the HSRP active state. The relevant HSRP parameters for the
description WirelessData router configuration are shown in Table 22.
ip address 10.5.50.1 255.255.255.0 Table 22. WAN Remote-Site HSRP Parameters (Dual Router)
ip pim sparse-mode Virtual IP
! HSRP Address Real IP HSRP PIM DR
interface GigabitEthernet0/2.69 Router Role (VIP) Address Priority Priority
description Voice MPLS CE Active .1 .2 110 110
ip address 10.5.53.1 255.255.255.0 DMVPN Spoke Standby .1 .3 105 105
ip pim sparse-mode
! The IP addresses assigned override those configured with the previous
interface GigabitEthernet0/2.70 Procedure 8, so that the default gateway IP address remains consistent
description WirelessVoice across locations with single or dual routers.
encapsulation dot1Q 70 The dual-router access layer design requires a modification for resilient
ip address 10.5.51.1 255.255.255.0
multicast. The PIM DR should be on the HSRP active router. The DR is
ip pim sparse-mode normally elected based on the highest IP address, and has no awareness of
the HSRP configuration. In this design, the HSRP active router has a lower
real IP address than the HSRP standby router, which requires a modification
to the PIM configuration. The PIM DR election can be influenced by explicitly
setting the DR priority on the LAN facing subinterfaces for the routers.
Note that the HSRP priority and PIM DR priority are shown in Table 22 to
be the same value; however, there is no requirement that these values must
be identical.
This procedure should be repeated for all data or voice subinterfaces.
ip address [LAN network 1 address] LAN network 1 netmask]

ip pim sparse-mode Procedure 11 Configure EIGRP (LAN Side)
ip pim dr-priority [PIM DR priority] [Dual-Router Design Only]
standby [number] ip [LAN network 1 gateway address] [LAN
network 1 netmask] A routing protocol must be configured between the two routers to ensure
standby [number] priority [priority] that the HSRP active router has full reachability information for all WAN
standby [number] preempt remote sites.
Procedure Steps:
Procedure 9 Example—DMVPN Spoke Router
interface GigabitEthernet0/2.64 1. Enable EIGRP-100.
description Data 2. Redistribute EIGRP-200 (DMVPN) into EIGRP-100.
ip address 10.5.52.3 255.255.255.0
ip helper-address 10.4.200.10 Step 1: Enable EIGRP-100.
ip pim sparse-mode EIGRP-100 is configured facing the access layer. In this design, all LAN-
standby 1 ip 10.5.52.1 facing interfaces and the loopback must be EIGRP interfaces. All interfaces
standby 1 priority 105 except the transit network subinterface should remain passive. The network
standby 1 preempt range must include all interface IP addresses either in a single network
statement or in multiple network statements. This design uses a best prac-
tice of assigning the router ID to a loopback address. Do not include the
Procedure 10 Configure Transit Network mGRE tunnel interface as an EIGRP interface for this EIGRP process.
The transit network is configured between the two routers. This network is passive-interface default
used for router-router communication and to avoid hair-pinning. The transit no passive-interface [interface]
network should use an additional subinterface on the router interface that is eigrp router-id [IP address of Loopback0]
already being used for data or voice. no auto-summary
There are no end stations connected to this network so HSRP and DHCP are
not required. Step 2: Redistribute EIGRP-200 (DMVPN) into EIGRP-100.
interface [interface type] [number].[sub-interface number] This step should only be completed on the DMVPN spoke router.
ip address [transit net address] [transit net netmask] EIGRP-200 is already configured for the DMVPN mGRE interface. Routes
from this EIGRP process are redistributed. Since the routing protocol is the
Procedure 10 Example—DMVPN Spoke Router same, no default metric is required.
interface GigabitEthernet0/2.99 router eigrp [as number]
description Transit Net redistribute eigrp [as number (DMVPN)]
ip address 10.5.48.2 255.255.255.252 Procedure 11 Example—DMVPN Spoke Router
router eigrp 100
network 10.5.0.0 0.0.255.255
no passive-interface GigabitEthernet0/1.99
no auto-summary

Deploying a WAN Remote-Site Distribution Layer Step 1: Configure the port-channel interface.
This set of procedures is for the configuration of a MPLS CE router for a Create the port-channel interface. As a best practice, use the same channel
MPLS WAN remote site (single-router, single-link) and includes all required numbering on both sides of the link where possible.
procedures to connect to a distribution layer. interface Port-channel [number]
no ip address
remote site. Use these procedures to connect a distribution layer to a
dual-role MPLS CE and DMVPN spoke router in the single-router, dual-link Step 2: Configure the port channel subinterfaces and assign IP addresses.
design. These procedures should also be used when connecting a distribu- After the physical interface has been enabled, then the appropriate subin-
tion layer to the first router of the dual-router, dual-link design. terfaces can be mapped to the VLANs on the distribution layer switch. The
Process them the same simplifies the overall configuration.
The subinterface configured on the router corresponds to a VLAN interface
on the distribution-layer switch. Traffic is routed between the devices with
the VLAN acting as a point-to-point link.
Remote-Site MPLS CE Router Distribution Layer
interface Port-channel [number].[sub-interface number]
1. Connect the MPLS CE Router to the Distribution Layer encapsulation dot1Q [dot1q VLAN tag]
2. Configure EIGRP (LAN side)
The following procedure is only relevant for the dual-router design Step 3: Administratively enable the port channel group members and assign
3. Configure the Transit Network
Not all router platforms can support LACP to negotiate with the switch, so
EtherChannel is configured statically .
no ip address
Procedure 1 Connect MPLS CE Router to Distribution Layer channel-group [number]
no shutdown
A Layer 2 port-channel interface connects to the WAN distribution switch. Procedure 1 Example
This connection allows for multiple VLANs to be included on the interface Port-channel1
EtherChannel if necessary. no ip address
The following configuration creates an EtherChannel link between the router interface Port-channel1.50
and switch, with two channel-group members. encapsulation dot1Q 50
ip address 10.5.0.1 255.255.255.252
Procedure Steps: ip pim sparse-mode
!
1. Configure the port-channel interface. interface GigabitEthernet0/1
no ip address
2. Configure the port-channel subinterfaces and assign IP addresses. channel-group 1
no shutdown
3. Administratively enable the port channel group members and assign !
the appropriate channel group. interface GigabitEthernet0/2
no ip address
channel-group 1
no shutdown

Procedure 2 Example—MPLS CE Router
Procedure 2 Configure EIGRP (LAN Side) router eigrp 100
default-metric 100000 100 255 1 1500
network 10.5.0.0 0.0.255.255
A routing protocol must be configured between the router and redistribute bgp 65511
distribution layer. passive-interface default
Procedure Steps: no passive-interface Port-channel1.50
1. Enable EIGRP-100. no auto-summary
2. Redistribute BGP into EIGRP-100.
Procedure 3 Configure the Transit Network

Step 1: Enable EIGRP-100. [Dual-Router Design Only]
EIGRP-100 is configured facing the distribution layer. In this design, all distribu- The transit network is configured between the two routers. This network is
tion-layer-facing subinterfaces and the loopback must be EIGRP interfaces. used for router-router communication and to avoid hair-pinning. The transit
All other interfaces should remain passive. The network range must include network should use an additional subinterface on the EtherChannel inter-
all interface IP addresses either in a single network statement or in multiple face that is already used to connect to the distribution layer.
network statements. This design uses a best practice of assigning the router
ID to a loopback address. The transit network must be a non-passive EIGRP interface.
router eigrp [as number] There are no end stations connected to this network so HSRP and DHCP are
network [network] [inverse mask] not required.
ip address [transit net address] [transit net netmask]
no auto-summary
Procedure 3 Example—MPLS CE Router

Step 2: Redistribute BGP into EIGRP-100.
interface Port-channel1.99
This step should only be completed on a MPLS CE router description Transit Net
The BGP routes are redistributed into EIGRP with a default metric. By
ip address 10.5.0.9 255.255.255.252
ip pim sparse-mode
Command Reference:
router eigrp 100
default-metric bandwidth delay reliability loading mtu
no passive-interface Port-channel1.99
bandwidth Minimum bandwidth of the route in kilobytes per
second
delay Route delay in tens of microseconds.
default-metric [bandwidth] [delay] 255 1 1500
redistribute bgp [BGP ASN]

Step 2: Configure the port-channel subinterfaces and assign IP addresses.
Process
Once the physical interface has been enabled, then the appropriate subin-
terfaces can be mapped to the VLANs on the distribution-layer switch. The
Remote-Site DMVPN Spoke Router Distribution Layer them the same simplifies the overall configuration.
1. Connect the DMVPN Spoke Router to the Distribution Layer The subinterface configured on the router corresponds to a VLAN interface
2. Configure EIGRP (LAN side) on the distribution-layer switch. Traffic is routed between the devices with
the VLAN acting as a point-to-point link.
The following procedure is only relevant for the dual-router design interface Port-channel [number].[sub-interface number]
3. Configure the Transit Network encapsulation dot1Q [dot1q VLAN tag]
Step 3: Enable the port-channel group members and assign the appropriate
This set of procedures is for the configuration of a DMVPN spoke router for channel group.
a DMVPN remote site (single-router, single-link) and includes all required
procedures to connect to a distribution layer. Not all router platforms can support LACP to negotiate with the switch, so
EtherChannel is configured statically.
remote site. Use these procedures to connect a distribution layer when no ip address
configuring the second router of the dual-router, dual-link design. channel-group [number]
no shutdown
Procedure 1 Example
Procedure 1 Connect DMVPN Spoke Router to Distribution Layer interface Port-channel2
no ip address
A Layer 2 port-channel interface connects to the WAN distribution
switch. This connection allows for multiple VLANs to be included on the interface Port-channel2.54
EtherChannel if necessary.
ip address 10.5.0.5 255.255.255.252
The following configuration creates an EtherChannel link between the router ip pim sparse-mode
and switch, with two channel-group members. !
Procedure Steps: no ip address
1. Configure the port-channel interface. channel-group 2
no shutdown
2. Configure the port-channel subinterfaces and assign IP addresses. !
3. Administratively enable the port-channel group members and assign
no ip address
the appropriate channel group. channel-group 2
Step 1: Configure the port-channel interface. no shutdown
Create the port-channel interface. As a best practice, use the same channel
numbering on both sides of the link where possible.
interface Port-channel [number]
no ip address

Procedure 2 Configure EIGRP (LAN Side) Procedure 3 Configure the Transit Network
A routing protocol must be configured between the router and The transit network is configured between the two routers. This network is
distribution layer. used for router-router communication and to avoid hair-pinning. The transit
network should use an additional subinterface on the EtherChannel inter-
Procedure Steps: face that is already used to connect to the distribution layer.
1. Enable EIGRP-100. The transit network must be a non-passive EIGRP interface.
2. Redistribute EIGRP-200 (DMVPN) into EIGRP-100. There are no end stations connected to this network so HSRP and DHCP are
not required.
Step 1: Enable EIGRP-100. interface [interface type] [number].[sub-interface number]
EIGRP-100 is configured facing the distribution layer. In this design, all distri- ip address [transit net address] [transit net netmask]
bution-layer-facing subinterfaces and the loopback must be EIGRP interfaces.
All other interfaces should remain passive. The network range must include all Procedure 3 Example—DMVPN Spoke Router
interface IP addresses either in a single network statement or in multiple network interface Port-channel2.99
statements. This design uses a best practice of assigning the router ID to a description Transit Net
loopback address. encapsulation dot1Q 99
router eigrp [as number] ip address 10.5.0.10 255.255.255.252
network [network] [inverse mask] ip pim sparse-mode
no passive-interface [interface] router eigrp 100
eigrp router-id [IP address of Loopback0] no passive-interface Port-channel2.99
no auto-summary
Step 2: Redistribute EIGRP-200 (DMVPN) into EIGRP-100.

Process
This step should only be completed on the DMVPN spoke router.
EIGRP-200 is already configured for the DMVPN mGRE interface. Routes
from this EIGRP process are redistributed. Because the routing protocol is Remote-Site WAN Distribution Layer Switch Configuration
the same, no default metric is required.
1. Complete the Distribution Layer Switch Universal Configuration
redistribute eigrp [as number (DMVPN)] 2. Connect to the WAN Routers
3. Configure EIGRP
Procedure 2 Example—DMVPN Spoke Router
4. Configure the Transit Network VLAN
router eigrp 100
network 10.5.0.0 0.0.255.255
no passive-interface Port-channel2.54 Procedure 1 Finish Dist. Layer Switch Universal Config
no auto-summary
This guide assumes that the distribution layer switch has already been

configured. Only the procedures required to complete the connection assign the appropriate channel group. Configure for 802.1 VLAN trunking.
of the switch to the WAN edge routers are included. Full details on
Not all router platforms can support LACP to negotiate with the switch, so
distribution layer switch configuration are included in the Cisco SBA for
EtherChannel is configured statically.
Large Agencies—Borderless Networks LAN Deployment Guide.
switchport trunk encapsulation dot1q
switchport trunk allowed vlan [VLAN number]
Procedure 2 Connect to the WAN Routers switchport mode trunk
channel-group [number] mode on
no shutdown
The port-channel interface(s) connect to either single or dual WAN routers,
and these connections are Layer 2 port channels. The following configura- Procedure 2 Example
tion creates an EtherChannel link between the switch and a router, with two vlan 50
channel-group members. This procedure is repeated for an additional WAN !
router if necessary. interface Port-channel1
description MPLS CE router
Procedure Steps: switchport trunk encapsulation dot1q
switchport trunk allowed vlan 50
1. Create the VLAN for the router link on the switch, create the VLAN
switchport mode trunk
interface and assign the IP address. !
2. Configure the port-channel interface and configure for 802.1Q VLAN interface GigabitEthernet1/0/1
trunking. description MPLS CE router port 1
3. Administratively enable the port-channel group members and assign switchport trunk allowed vlan 50
the appropriate channel group. Configure for 802.1 VLAN trunking. switchport mode trunk
channel-group 1 mode on
no shutdown
Step 1: Create the VLAN for the router link on the switch, create the !
VLAN interface and assign the IP address. interface GigabitEthernet2/0/1
Create the point-to-point VLAN for the router link. description MPLS CE router port 2
vlan [VLAN number]
switchport trunk allowed vlan 50
Create the VLAN interface and assign the IP address for the channel-group 1 mode on
point-to-point link. no shutdown
interface Vlan [VLAN number] !
ip address [IP address] [netmask] interface Vlan50
ip address 10.5.0.2 255.255.255.252
Step 2: Configure the port channel interface and configure for 802.1q
VLAN trunking. Procedure 3 EIGRP Configuration
link where possible. Enable EIGRP for the IP address space that the network will be using.
interface Port-channel [number] If needed for your network, you can enter multiple network statements.
switchport trunk encapsulation dot1q Disable auto summarization of the IP networks and enable all routed links
switchport trunk allowed vlan [VLAN number] to be passive by default. The Loopback 0 IP address is used for the EIGRP
router ID to ensure maximum resiliency.
Step 3: Administratively enable the port-channel group members and

The single logical distribution layer design uses stateful switchover and
nonstop forwarding to provide sub-second failover in the event of a supervi- Procedure 4 Configure Transit Network VLAN
sor data or control plane failure. This ability reduces packet loss in switcho-
ver to redundant logic and keeps packets flowing when the data plane is
The transit network is configured between the two routers; however, a physi-
still intact to adjacent nodes. In the stack-based distribution layer approach,
cal link between the routers is not required. Instead a transit VLAN is used.
a single logical control point still exists and the master control plane in a
The distribution layer extends the VLAN across the two existing Layer 2
stack can failover to another member in the stack providing near-second or
EtherChannels. The distribution layer does not participate in any routing on
sub-second resiliency.
the transit network so a VLAN interface is not required for the transit VLAN.
When the supervisor or master switch of a distribution platform switches
Procedure Steps:
IP data traffic flows in hardware. However, the supervisor requires time to 1. Create the transit VLAN on the switch.
reestablish control plane two-way peering with EIGRP routing neighbors and 2. Add the transit VLAN to the existing port-channel trunk interface and
avoid the peer router from tearing down adjacencies due to missed hellos channel group members.
the supervisor to recover, there is a Nonstop Forwarding (NSF) setting for
the routing protocol to wait for the dual supervisor peer switch to recover. Step 1: Create the transit VLAN on the switch.
The neighboring router is said to be NSF aware if it has a release of IOS that Create the transit VLAN.
recognizes an NSF peer. All of the platforms used in this design are NSF
vlan [VLAN number]
aware for the routing protocols in use.
The distribution layer switch must be configured to enable Nonstop Step 2: Add the transit VLAN to the existing port-channel trunk interface
Forwarding for the protocol in use so that it can signal a peer when it and channel group members.
switches over to a Hot-Standby supervisor for the peering neighbor to allow interface Port-channel [number]
it time to reestablish EIGRP protocol to that node. No tuning of the default switchport trunk allowed vlan add [VLAN number]
NSF timers is needed in this network. Nothing has to be configured for an !
NSF aware peer router. interface [interface type] [number]
router eigrp [as number] switchport trunk allowed vlan add [VLAN number]
passive-interface default Procedure 4 Example
vlan 99
!
no auto-summary
interface Port-channel1
nsf
switchport trunk allowed vlan add 99
!
Procedure 3 Example interface GigabitEthernet1/0/1
router eigrp 100 switchport trunk allowed vlan add 99
network 10.5.0.0 0.0.255.255 !
passive-interface default interface GigabitEthernet2/0/1
no passive-interface Vlan50 switchport trunk allowed vlan add 99
no auto-summary
nsf

Deploying WAN Quality of Service The following steps are used to configure the required WAN class-maps and
matching criteria.
Process
Step 1: Create the class maps for DSCP matching.
This step will be repeated to create a class-map for each of the six WAN
QoS Configuration classes of service listed in Table 23.
1. Create the WAN QoS Class Maps to Classify Traffic Types
You do not need to explicitly configure the default class.
2. Create the Policy Map to Mark BGP Traffic class-map match-any [class-map name]
3. Add DMVPN ISAKMP Traffic to NETWORK-CRITICAL Class of match ip dscp [dcsp value] [optional additional dscp value(s)]
Service
Table 23. QoS Classes of Service
4. Define the Policy Map to Implement the Queuing Policy
5. Configure Physical Interface Shaping and Queuing Policy Class of Traffic DSCP Bandwidth Congestion
Service type Value(s) % Avoidance
6. Apply the WAN QoS Policy to a Physical interface
VOICE Voice traffic ef 10 (PQ)
INTERACTIVE- Interactive cs4, af41 23 (PQ)
When configuring the WAN-edge QoS, you are defining how traffic will VIDEO video
egress your network. It is critical that the classification, marking, and band- (video
width allocations align to the service provider offering in order to ensure conferenc-
consistent QoS treatment end to end. ing)
CRITICAL-DATA Highly inter- af31, cs3 15 DSCP based
active (such
Procedure 1 Create the QoS Maps to Classify Traffic as Telnet,
Citrix, and
Oracle thin
This procedure applies to all WAN routers. clients)
Procedure Steps: DATA Data af21 19 DSCP based
1. Create the class maps for DSCP matching. SCAVENGER Scavenger af11, cs1 5
2. Create a class map for BGP protocol matching. NETWORK- Routing cs6, cs2 3
CRITICAL protocols.
The class-map command is used to define a traffic class and identify Operations,
traffic to associate with the class name. These class names are used when administra-
configuring policy maps that define actions you wish to take against the tion and
traffic type. The class-map command sets the match logic. In this case, the mainte-
match-any keyword indicates that the maps matches any of the specified nance
criteria. This keyword is followed by the name you wish to assign to the class (OAM)
of service. After you have configured the class-map command, you define traffic.
specific values, such as DSCP and protocols to match with the match com-
mand. Two forms of the match command are used: match dscp and match default Best effort other 25 random
protocol.

Step 2: Create a class map for BGP protocol matching. To ensure proper treatment of BGP routing traffic in the WAN, you must
assign a DSCP value of cs6. Although the class-map you created in the
BGP traffic is not explicitly tagged with a DSCP value. Network Based
previous step matches all BGP traffic to the class named BGP, you must
Application Recognition (NBAR) is used to match BGP by protocol.
configure a policy-map to assign the required DSCP value to all BGP traffic.
This step is only required for a WAN-aggregation MPLS CE router or a WAN policy-map [policy-map name]
remote-site MPLS CE router that is using BGP. class [class-map name to match]
class-map match-any [class-map name] set dscp [dcsp value]
match ip protocol [protocol name]
Procedure 2 Example
Procedure 1 Example policy-map MARK-BGP
class-map match-any VOICE class BGP
match dscp ef set dscp cs6
class-map match-any INTERACTIVE-VIDEO

match dscp cs4 af41 Procedure 3 Add DMVPN ISAKMP Traffic to NETWORK
class-map match-any CRITICAL-DATA

For a WAN connection using DMVPN, you need to ensure proper treatment
match dscp af31 cs3
of ISAKMP traffic in the WAN. To classify this traffic requires the creation of
class-map match-any DATA an access-list and the addition of the access-list name to the NETWORK-
match ip dscp af21 CRITICAL class-map created in Procedure 1.
This procedure is only required for a WAN-aggregation DMVPN hub router
class-map match-any SCAVENGER
or a WAN remote-site DMVPN spoke router.
match ip dscp af11 cs1
Procedure steps:
class-map match-any NETWORK-CRITICAL
match ip dscp cs6 cs2 1. Create the access-list.
2. Add the match criteria to the existing NETWORK-CRITICAL class-map.
class-map match-any BGP
match protocol bgp
Step 1: Create the access-list.
ip access-list extended [name]
permit [protocol] [source] eq [port] [destination] eq [port]
Tech Tip
Step 2: Add the match criteria to the existing NETWORK-CRITICAL
class-map.
You do not need to configure a Best-Effort Class. This is implicitly
class-map match-any [class-map name]
included within class-default as shown in Procedure 4. match access-group name [name]
Procedure 3 Example
Procedure 2 Create the Policy Map to Mark BGP Traffic ip access-list extended ISAKMP
permit udp any eq isakmp any eq isakmp
This procedure is only required for a WAN-aggregation MPLS CE router or a class-map match-any NETWORK-CRITICAL
WAN remote-site MPLS CE router that is using BGP. match access-group name ISAKMP

Step 3: Assign the maximum guaranteed bandwidth for the class.
Procedure 4 Define Policy Map to use the Queuing Policy
This is an optional step.
bandwidth percent [percentage]
This procedure applies to all WAN routers. Step 4: Define the priority queue for the class.
The WAN policy map references the class names you created in the previ- This is an optional step.
ous procedures and defines the queuing behavior along with the maximum priority percent [percentage]
guaranteed bandwidth allocated to each class. This specification is accom-
plished with the use of a policy-map. Then each class within the policy Step 5: Apply the child service policy.
map invokes an egress queue, assigns a percentage of bandwidth, and This is an optional step only for the NETWORK-CRITICAL class of service
associates a specific traffic class to that queue. One additional default class with the MARK-BGP child service policy.
defines the minimum allowed bandwidth available for best effort traffic. service-policy {policy-map-name]
Step 6: Define the congestion mechanism.
Tech Tip This is an optional step.
random-detect [type]
Procedure 4 Example
The local router policy maps define seven classes while most service
policy-map WAN
providers offer only six classes of service. The NETWORK-CRITICAL
class VOICE
policy map is defined to ensure the correct classification, marking, and priority percent 10
queuing of network-critical traffic on egress to the WAN. After the traffic class INTERACTIVE-VIDEO
has been transmitted to the service provider, the network-critical traffic priority percent 23
is typically remapped by the service provider into the critical data class. class CRITICAL-DATA
bandwidth percent 15
random-detect dscp-based
Procedure Steps: class DATA
1. Create the parent policy map. bandwidth percent 19
random-detect dscp-based
2. Apply the previously created class-map. class SCAVENGER
bandwidth percent 5
3. Assign the maximum guaranteed bandwidth for the class (optional).
class NETWORK-CRITICAL
4. Define the priority queue for the class (optional). bandwidth percent 3
service-policy MARK-BGP
5. Apply the child service policy (optional). class class-default
6. Define the congestion mechanism (optional). bandwidth percent 25
random-detect
Step 1: Create the parent policy map.
policy-map [policy-map-name]
Tech Tip
Steps 2–6 are repeated for each class in Table 23 including class-default.
Step 2: Apply the previously created class-map. While these bandwidth assignments represent a good baseline it is
class [class-name] important to consider your actual traffic requirements per class and
adjust the bandwidth settings accordingly.

Procedure 5 Example
Procedure 5 Configure Physical Interface S&Q Policy
This example shows a router with a 20-Mbps link on interface
GigabitEthernet0/0 and a 10-Mbps link on interface GigabitEthernet0/1.
With WAN interfaces using Ethernet as an access technology, the demarca- policy-map WAN-INTERFACE-G0/0
tion point between the agency and service provider may no longer have class class-default
a physical-interface bandwidth constraint. Instead, a specified amount of shape average 20000000
access bandwidth is contracted with the service provider. To ensure the service-policy WAN
offered load to the service provider does not exceed the contracted rate !
that results in the carrier discarding traffic, shaping needs to be configured policy-map WAN-INTERFACE-G0/1
class class-default
on the physical interface. This shaping is accomplished with a QoS service
shape average 10000000
policy. A QoS service policy is configured on the outside Ethernet interface, service-policy WAN
and this parent policy includes a shaper that then references a second or
subordinate (child) policy that enables queuing within the shaped rate. This
is called a hierarchical Class-Based Weighted Fair Queuing (HCBWFQ)
Procedure 6 Apply WAN QoS Policy to a Physical Interface
configuration. When configuring the shape average command, ensure the
value matches the contracted bandwidth rate from your service provider.
To invoke shaping and queuing on a physical interface, you must apply the
This procedure applies to all WAN routers. This procedure may be repeated parent policy configured in the previous procedure.
multiple times to support devices that have multiple WAN connections
attached to different interfaces. This procedure applies to all WAN routers. This procedure may be repeated
multiple times to support devices that have multiple WAN connections
Procedure Steps: attached to different interfaces.
1. Create the parent policy map. Procedure Steps:
2. Configure the shaper. 1. Select the WAN interface.
3. Apply the child service policy. 2. Apply the WAN QoS policy.
Step 1: Create the parent policy map. Step 1: Select the WAN interface.
As a best practice, embed the interface name within the name of the parent interface [interface type] [number]
policy map.
policy-map [policy-map-name] Step 2: Apply the WAN QoS policy.
The service policy needs to be applied in the outbound direction.
Step 2: Configure the shaper.
service-policy output [policy-map-name]
class [class-name]
shape [average | peak] [bandwidth (kbps)]
Procedure 6 Example
Step 3: Apply the child service policy.
service-policy output WAN-INTERFACE-G0/0
policy-map [policy-map-name] !
service-policy output WAN-INTERFACE-G0/1

Deploying Application Optimization with WAAS WAN 100 design uses a cluster of WAE-7341 devices and the total number
Application Optimization Agency Overview of devices required is a minimum of 2 (for N+1 redundancy). Additional detail
on the WAE sizing is provided in Table 24. The fan-out numbers correspond to
The number of remote work sites is increasing, so network administrators the total number of remote-peer WAE devices.
need tools to help them ensure solid application performance in remote
locations. Recent trends have the number of remote sites increasing and Table 24. WAN-Aggregation WAE Options
that a majority of new hires are located at remote sites. These trends are
Max Max Max Max
tied to global expansion, employee attraction and retention, mergers and
Optimized Recommended Optimized Core
acquisitions, cost savings, and environmental concerns.
TCP WAN Link Throughput Fan-out
In the meantime, remote-site communications requirements are evolving Device Connections [Mbps] [Mbps] [Peers]
to embrace collaborative applications, video, and Web 2.0 technologies. WAVE-574-3GB 00750 0008 0100 0035
These developments are also placing greater performance demands on the
remote sites and the WAN. WAVE-574-6GB 01300 0020 0150 0070
WAE-674-4GB 02000 0045 0250 0100
The trend toward data-center consolidation also continues. The consolida-
tion efforts move most remote-site assets into data centers, largely to WAE-674-8GB 06000 0090 0350 0200
comply with regulatory mandates for centralized security and stronger WAE-674-8GB-VB 04000 0090 0350 0200
control over agency data assets.
WAE-7341 12000 0310 1000 1400
Consolidating data centers while growing the remote-site population means WAE-7371 50000 1000 2500 2800
that increasing numbers of remote employees access LAN-based agency
applications across comparatively slow WANs. With these applications
growing increasingly multimedia-centric and latency-sensitive, IT and net- A more comprehensive, interactive WAAS sizing tool is available for regis-
working staffs are further challenged to keep remote-application response tered users of cisco.com: http://tools.cisco.com/WAAS/sizing
times on par with the experiences of users situated locally to the agency’s The WCCP is a protocol developed by Cisco. Its purpose is to transparently
application servers in the data center. These local users enjoy multimegabit intercept and redirect traffic from a network device to a WCCP appliance
LAN speeds and are not affected by any distance-induced delay, unlike their such as a WAE running WAAS (discussed below).
counterparts at the other end of a WAN connection.
WCCP is enabled on the MPLS CE and DMVPN routers. The WCCP redirect
Application optimization can boost network performance along with enhanc- uses service groups 61 and 62 to match traffic for redirection. These service
ing security and improving application delivery. Cisco WAN Optimization groups must be used in pairs.
is an architectural solution comprising a set of tools and techniques that work
together in a strategic systems approach to provide best-in-class WAN • Service group 61 uses the source address to redirect traffic
optimization performance while minimizing its total cost of ownership. • Service group 62 uses the destination address to redirect traffic
Application Optimization Technical Overview This design uses WCCP 61 inbound on LAN-facing interfaces to match
unoptimized data sourced from the data center that is destined for clients at
WAN Aggregation the WAN remote sites. WCCP 62 is used inbound on WAN-facing interfaces,
The WAN-aggregation site uses a cluster of two or more WAE devices to matching optimized data sourced from the WAN remote sites.
provide WAAS capabilities as shown in Figure 30. The WAE appliances
The connections from the switch to the MPLS CE and DMVPN routers are all
connect to the distribution-layer switch. The connections use EtherChannel
routed point-to-point links. This design mandates the use of a negotiated-
both for increased throughput and for resiliency. The WAEs connect to the
return GRE tunnel from WAE to router. When a design uses a GRE negoti-
WAN services network that is configured on the distribution switch.
ated return, it is not required to extend the WAN services VLAN to include
The WAN 500 design uses a cluster of WAE-7371 devices. The total number the MPLS CE and DMVPN routers.
of devices required is a minimum of 2 (for N+1 redundancy). Similarly, the

Figure 30. WAN Aggregation—WAAS Topology Table 25. WAN Remote-Site WAE Options
Max Max Max

Optimized Recommended Optimized
TCP WAN Link Throughput
Device Connections [Mbps] [Mbps]
NME-WAE-302 250 4 90
NME-WAE-502 400 4 150
SRE-700-S 200 20 200
SRE-700-M 500 20 200
SRE-900-S 200 50 300
SRE-900-M 500 50 300
SRE-900-L 1000 50 300
WAVE-274 200 2 90
WAVE-474 400 4 90
WAVE-574-3GB 750 8 100
WAVE-574-6GB 1300 20 150
WAE-674-4GB 2000 45 250
Remote Sites WAE-674-8GB 6000 90 350
The WAN Optimization design for the remote sites can vary somewhat WAE-674-8GB-VB 4000 90 350
based on site-specific characteristics. Single router sites use a single (non-
WAE-7341 12000 310 1000
redundant) WAE. Similarly, all dual-router sites use dual WAEs. The specifics
of the WAE sizing and form-factor primarily depend on the number of end WAE-7371 50000 1000 2500
users and bandwidth of the WAN links. A more comprehensive, interactive WAAS sizing tool is available for regis-
There are many factors to consider in the selection of the WAN remote-site tered users of cisco.com: http://tools.cisco.com/WAAS/sizing
WAE devices. The primary parameter of interest is the bandwidth of the The WAE form factors previously discussed include a router enhanced
WAN link. After the bandwidth requirement has been met, the next item network module (NME), a router Service Ready Engine (SRE), and an external
under consideration is the maximum number of concurrent, optimized TCP appliance. These variants all run the same WAAS software and are function-
connections. Additional detail on the WAE sizing is provided in Table 25. ally equivalent. The primary difference is the method of LAN attachment for
The optimized throughput numbers correspond to the apparent bandwidth these devices.
available after successfully optimization by WAAS.
• NME: One internal interface (router connect only), one external interface
• SRE: One internal interface (router connect only), one external interface
• Appliance: Two interfaces (both external)
The approach for connecting the WAE devices to the LAN is to be consistent
regardless of the chosen hardware form-factor. All WAE connections are
made using the external interfaces. The benefit of this method is that it is

not necessary to create a dedicated network specifically to attach the WAE Figure 32. WAN Remote Site—WAAS Topology (Distribution Layer
devices, and the SRE, NME, and appliance devices can use an identical Connection)
design. The internal interfaces of the NME and SRE are not used for this
design, except for the initial bootstrapping of the device configurations.
NOTE: You must connect an external Ethernet cable from each NME or SRE
module for this solution.
Figure 31. WAN Remote Site—WAAS Topology (Access Layer Connection)
The WAE appliance(s) should be connected, where possible, through both

interfaces using EtherChannel for performance and resiliency.
WCCP Version 2 is enabled on the WAN routers to redirect traffic to the
WAAS appliances.
The WAE device(s) should connect to the data VLAN of the access switch in
all flat Layer 2 designs as shown in Figure 31. When the deployment uses a The WCCP redirect uses service groups 61 and 62 to match traffic for redi-
distribution-layer design, the WAE device(s) should connect to the primary rection. These services groups must be used in pairs.
data VLAN on the distribution switch as shown in Figure 32. • Service group 61 uses the source address to redirect traffic
• Service group 62 uses the destination address to redirect traffic
This design uses WCCP 61 inbound on LAN-facing VLAN subinterfaces
to match unoptimized data sourced from the clients destined for the data
center (or other remote sites). In all cases, WCCP 62 is used inbound on
WAN-facing interfaces to match optimized data sourced from the data
center (or other remote sites).
Because the WAE is connected to the data VLAN, this design requires the
use of a negotiated-return GRE tunnel from the WAE to the router. When
using a GRE-negotiated return, you are not required to create a new network
on the routers specifically to attach the WAEs.

6> to change specific default [y]: n
Process
Step 2: Configure as central manager.
1. Application Accelerator
WAAS/WAE Configuration
2. Central Manager
Select device mode [1]: 2
The following steps provide an overview of the tasks required to
configure a basic WAAS environment. Step 3: Configure time zone.
1. Configure the WAAS Central Manager Enter Time Zone <Time Zone Hours(-23 to 23) Minutes(0-59)>
[UTC 0 0]: PST -8 0
2. Configure Switch for WAE Appliances
3. Configure the WAE Appliance Devices Step 4: Configure management interface, IP address, and default gateway.
4. Configure the WAE SRE and NME Devices No. Interface Name IP Address Network Mask
5. Configure Remote Switch for WAE Devices 1. GigabitEthernet 1/0 dhcp
6. Configure WCCPv2 on Routers 2. GigabitEthernet 2/0 dhcp
Select Management Interface [1]: 1
Enable Autosense for Management Interface? (y/n)[y]: y
Enable DHCP for Management Interface? (y/n)[y]: n
Enter Management Interface IP Address
Procedure 1 Configure the WAAS Central Manager <a.b.c.d or a.b.c.d/X(optional mask bits)> [Not configured]:
10.4.200.100/24
Enter Default Gateway IP Address [Not configured]: 10.4.200.1
A Cisco WAVE-574 device is used for the Central Manager function at the pri-
mary location to provide graphical management, configuration, and report-
ing for the WAAS network. This device resides in the server farm because it Step 5: Configure DNS, host, and NTP settings.
is not directly in the forwarding path of the WAN optimization, but provides Enter Domain Name Server IP Address [Not configured]:
management and monitoring services. Initial configuration of the Central 10.4.200.10
Manager requires terminal access to the console port for basic configura- Enter Domain Name(s) (Not configured): cisco.local
tion options and IP address assignment. For all WAE devices, the factory Enter Host Name (None): bn-waas-wcm-1
Enter NTP Server IP Address [None]: 10.4.200.17
default username is admin and the factory default password is default.
You can start the initial setup utility from the command line by entering the Step 6: Select appropriate license.
setup command. The product supports the following licenses:
Step 1: Run setup. 1. Enterprise
Parameter Default Value Enter the license(s) you purchased [1]: 1
1. Device Mode Application Accelerator
2. Interception Method WCCP Step 7: Verify configuration settings and initiate reload.
3. Time Zone UTC 0 0 Parameter Configured Value
4. Management Interface GigabitEthernet 1/0 1. Device Mode Central Manager
5. Autosense Enabled 2. Time Zone PST -8 0
6. DHCP Enabled 3. Management Interface GigabitEthernet 1/0
ESC Quit ? Help —————————————— WAAS Default Configuration ————————— 4. Autosense Enabled
————— 5. DHCP Disabled
Press ‘y’ to select above defaults, ‘n’ to configure all, <1- 6. IP Address 10.4.200.100

7. IP Network Mask 255.255.255.0
8. IP Default Gateway 10.4.200.1
9. DNS IP Address 10.4.200.10
10. Domain Name(s) cisco.local
11. Host Name bn-waas-wcm-1
12. NTP Server Address 10.4.200.17
13. License Enterprise
ESC Quit ? Help ! CLI ───────── WAAS Final Configuration

─────────────
Press ‘y’ to select configuration, ‘d’ to toggle defaults
display, <1-13> to change specific parameter [y]: y
Apply WAAS Configuration: Device Mode changed in SETUP; New

configuration takes effect after a reload. If applicable,
registration with CM, CM IP address, WAAS WCCP configuration
etc, are applied after the reboot. Initiate system reload?
<y/n> [n] y
Are you sure? <y/n> [n]: y
Step 8: After the reboot, login to the WAAS Central Manager and
enable SSH.
Procedure 2 Configure Switch for WAE Appliances
Enabling SSH requires the generation of the RSA key and enabling of the
sshd service:
ssh-key-generate key-length 2048
sshd version 2 The WAN distribution switch is the appropriate location to physically con-
sshd enable nect devices at the WAN-aggregation site such as WAE appliances that
support WAN optimization. This device type requires a resilient connection
Step 9: Save the configuration. but does not require a routing protocol. This type of connection can use a
Layer 2 EtherChannel link.
After making configuration changes through the console, save the
configuration. This guide assumes that the distribution layer switch has already been
configured. Only the procedures required to complete the connection of the
copy running-config startup-config
switch to the WAE appliances are included. Full details on distribution layer
switch configuration are included in the Cisco SBA for Large Agencies—
Step 10: Access the WAAS Central Manager through the web interface. Borderless Networks LAN Deployment Guide.
The Central Manager device should now be up and running after the reload
completes, and be accessible to a web browser at the IP address assigned
during Step 6 of the setup utility, or at the associated hostname if it has
been configured in DNS. Specify secure HTTP and the port number 8443 to
access the Central Manager, for example https://10.4.200.100:8443. Login
using the default username of admin and password of default. Choosing My
WAN -> Manage Devices from the panel on the left should display a screen
showing the Central Manager initially as the only managed device.

You must create a VLAN and SVI for this and other devices with similar no shutdown
connectivity requirements. This VLAN is referred to as the WAN service !
network. interface Vlan350
ip address 10.4.128.129 255.255.255.192
Procedure Steps:
1. On the WAN distribution switch, create the VLAN and SVI.
Procedure 3 Configuring the WAE Appliance Devices
2. On the WAN distribution switch, configure Layer 2 EtherChannel links
for the devices and associate them with the VLAN.
A cluster of Cisco WAE-7341 appliances is deployed at the WAN-aggregation
site to provide the headend termination for WAAS traffic to and from the
Step 1: Create the VLAN and SVI. remote sites across the WAN. These device are connected directly to the
vlan [VLAN number] WAN distribution-layer switch, leveraging GRE-negotiated return to com-
name [VLAN name] municate with the WCCP routers.
interface Vlan [VLAN number] WAE appliances may also be deployed at WAN remote sites, either individu-
ip address [IP address] [netmask] ally or as part of a WAE cluster. This procedure should be used for configure
WAN remote-site WAE appliances.
Step 2: Configure Layer 2 EtherChannel links for the devices and associate The same setup utility used in the initial configuration of the WAAS Central
them with the VLAN. Manager is used for the setup of the WAE appliance devices. These devices
interface Port-channel [number] only require basic setup through their console port to assign initial settings;
switchport access vlan [VLAN number] after you complete this setup, all management of the WAAS network can
be performed through the graphical interface of the WAAS Central
interface GigabitEthernet1/0/2 Manager system.
switchport access vlan [VLAN number]
channel-group [number] mode on Initial configuration of the WAE application accelerators requires terminal
no shutdown access to the console port for basic configuration options and IP address
! assignment. For all WAE devices, the factory default username is admin and
Procedure 3 Example the factory default password is default.
vlan 350 The setup utility configuration steps for the application accelerator WAEs
name WAN_Service_Net-10.4.128.128 are similar to the setup of the Central Manager, but the steps begin to differ
after you choose application-accelerator as the device mode in Step 2.
description bn-wae-1 EtherChannel After you choose this mode, the setup script changes to allow you to register
switchport access vlan 350 the WAE with the existing Central Manager, and to define the traffic intercep-
tion method as WCCP.
interface GigabitEthernet1/0/2 Step 1: Run setup.
description bn-wae-1 port 1
switchport access vlan 350 You can start the initial setup utility from the command line by entering the
channel-group 7 mode on setup command.
no shutdown Parameter Default Value
! 1. Device Mode Application Accelerator
interface GigabitEthernet2/0/2 2. Interception Method WCCP
description bn-wae-1 port 2 3. Time Zone UTC 0 0
switchport access vlan 350 4. Management Interface GigabitEthernet 1/0
channel-group 7 mode on 5. Autosense Enabled

6. DHCP Enabled Step 7: Configure WCCP router list.
Enter WCCP Router (max 4) IP Address list (ip1 ip2 ...) []:
ESC Quit ? Help ──────────── WAAS Default Configuration 10.4.128.241 10.4.128.242 10.4.128.243
──────────────
Press ‘y’ to select above defaults, ‘n’ to configure all, <1-
6> to change specific default [y]: n Step 8: Select appropriate license.
The product supports the following licenses:
1. Transport
Step 2: Configure as application accelerator.
2. Enterprise
1. Application Accelerator 3. Enterprise & Video
2. Central Manager 4. Enterprise & Virtual-Blade
Select device mode [1]: 1 5. Enterprise, Video & Virtual-Blade
Enter the license(s) you purchased [2]: 2
Step 3: Configure interception method.
1. WCCP Step 9: Verify configuration settings.
2. Other Parameter Configured Value
Select Interception Method [1]: 1 2. Interception Method WCCP
3. Time Zone PST -8 0
Step 4: Configure time zone. 4. Management Interface GigabitEthernet 1/0
Enter Time Zone <Time Zone Hours(-23 to 23) Minutes(0-59)> 5. Autosense Enabled
[UTC 0 0]: PST -8 0 6. DHCP Disabled
7. IP Address 10.4.128.161
8. IP Network Mask 255.255.255.248
Step 5: Configure management interface, IP address, and default gateway. 9. IP Default Gateway 10.4.128.129
No. Interface Name IP Address Network Mask 10. CM IP Address 10.4.200.100
1. GigabitEthernet 1/0 dhcp 12. Domain Name(s) cisco.local
2. GigabitEthernet 2/0 dhcp 13. Host Name bn-wae7341-1
Select Management Interface [1]: 1 14. NTP Server Address 10.4.200.17
Enable Autosense for Management Interface? (y/n)[y]: y 15. WCCP Router List 10.4.128.241 10.4.128.242
Enable DHCP for Management Interface? (y/n)[y]: n 10.4.128.243
Enter Management Interface IP Address 16. License Enterprise
<a.b.c.d or a.b.c.d/X(optional mask bits)> [Not configured]: ESC Quit ? Help ! CLI ────────── WAAS Final Configuration
10.4.128.161/29 ────────────
Enter Default Gateway IP Address [Not configured]: 10.4.128.129 Press ‘y’ to select configuration, <F2> to see all
Enter Central Manager IP Address (WARNING: An invalid entry configuration, ‘d’ to toggle defaults display, <1-16> to change
will cause SETUP to take a long time when applying WAAS specific parameter [y]: y
configuration) [None]: 10.4.200.100
Applying WAAS configuration on WAE ...
Step 6: Configure DNS, host, and NTP settings. May take a few seconds to complete ...
Enter Domain Name Server IP Address [Not configured]:
10.4.200.10 If the switch connection to the WAE is configured as a port-channel, this
Enter Domain Name(s) (Not configured): cisco.local procedure will fail, because the WAE setup script does not enable the port-
Enter Host Name (None): bn-wae7341-1 channel. If so, the registration with the WAAS Central Manager is completed
Enter NTP Server IP Address [None]: 10.4.200.17 manually in Step 11.

Step 10: Configure port-channel connection for WAE to connect to the Step 13: Configure GRE negotiated return.
distribution switch stack.
All WAE devices use GRE-negotiated return with their respective WCCP
This is an optional step only required when connecting the WAE using a port router(s):
channel for a resilient connection. egress-method negotiated-return intercept-method wccp
interface GigabitEthernet 1/0
no ip address 10.4.128.161 255.255.255.192 Step 14: Configure WCCP router list.
exit
! The setup script generated a router-list based on the information provided.
primary-interface PortChannel 1 To view the device configuration, enter the following command:
! bn-wae-7341-1# show running-config | include wccp router-list
interface PortChannel 1 wccp router-list 8 10.4.128.241 10.4.128.242 10.4.128.243
ip address 10.4.128.161 255.255.255.192
exit
! Router list 8 is specifically for use with WCCP configured on a default gate-
! way router. This design uses GRE-negotiated return and router loopback
interface GigabitEthernet 1/0 addresses so we need to create a new router list and delete router list 8.
channel-group 1
All WAE configurations in this design use router list 1.
exit
interface GigabitEthernet 2/0 no wccp router-list 8 10.4.128.241 10.4.128.242 10.4.128.243
channel-group 1 wccp router-list 1 10.4.128.241 10.4.128.242 10.4.128.243
exit
This design uses authentication between the routers and WAE. If any of the
Step 12: Complete registration with WAAS Central Manager. WCCP routers are Cisco ASR1000 Series routers, then change the default
setting of hash-source-ip to mask-assign. This change is made on the
After the port-channel has been configured, the WAE can reach the WAEs, not on the routers.
WAAS Central Manager. Run the cms enable command to force a wccp tcp-promiscuous router-list-num 1 password c1sco123 mask-
manual registration. assign
This is an optional step only required when connecting the initial attempt to
register in Step 9 has failed. Step 15: Enable SSH.
cms enable
Enabling SSH requires the generation of the RSA key and enabling of the
Registering WAAS Application Engine...
Sending device registration request to Central Manager with sshd service:
address 10.4.200.100 ssh-key-generate key-length 2048
Please wait, initializing CMS tables sshd version 2
Successfully initialized CMS tables sshd enable
Registration complete.
Please preserve running configuration using ‘copy running- Step 16: Save the configuration.
config startup-config’.
Otherwise management service will not be started on reload and After making configuration changes through the console, save the
node will be shown ‘offline’ in WAAS Central Manager UI. configuration.
management services enabled copy running-config startup-config
There are several additional non-default settings that are enabled on the
WAE devices to complete the configuration. These setting are configured in
Steps 13 through 15.

Step 2: Connect to the WAE console using a session from the host router.
Procedure 4 Configure the WAE SRE and NME Devices
After the IP address is assigned, and the interface is enabled, it is possible
to open a session on the WAE and run the setup script. For all WAE devices,
The remote-site WAAS equipment in this design can be a variety of WAE appli- the factory default username is admin and the factory default password is
ances, SRE, or NME-WAE form-factors, depending on the performance default.
requirements. If you are configuring a WAE appliance, use Procedure 3.
NOTE: If you are using secure user authentication on the router, then you
The SRE and NME-WAE modules can be inserted directly into a correspond- must first authenticate with a valid router login credential before logging into
ing module slot in the remote-site router and are configured somewhat the WAE console session.
differently from the appliances. If you are using an appliance, then you can
follow the WAN-Aggregation WAE Device set of procedures. bn-br203-2921-1# service-module sm 1/0 session
Although the remote-site router can potentially communicate directly with
the SRE or NME-WAE using the router backplane, this design leverages the Step 3: Run setup.
external interfaces on the modules, which allows for a consistent design
implementation regardless of the chosen WAE device. The Integrated- You can start the initial setup utility from the command line by entering the
Service-Engine interface must be enabled and have an arbitrary (locally setup command.
significant only) IP address assigned in order to be accessed through a Parameter Default Value
console session from the host router. Device Mode Application Accelerator
1. Interception Method WCCP
NOTE: You must connect the external interface to the data network on the 2. Time Zone UTC 0 0
access or distribution switch for this configuration to work properly. 3. Management Interface GigabitEthernet 1/0
(internal)
Autosense Disabled
Step 1: Configure console access and SRE or NME IP addresses on the DHCP Disabled
host router. ESC Quit ? Help ───────────── WAAS Default Configuration
To permit console access to the SRE or NME modules, you must enter the ─────────────
Press ‘y’ to select above defaults, ‘n’ to configure all, <1-
following commands on the host router (this example shows a SRE service
3> to changespecific default [y]: n
module).
interface SM1/0
ip address 1.1.1.1 255.255.255.252 Step 4: Configure interception method.
service-module external ip address 10.5.52.8 255.255.255.0 1. WCCP
service-module ip default-gateway 10.5.52.1 2. Other
no shutdown Select Interception Method [1]: 1
Step 5: Configure time zone.

Enter Time Zone <Time Zone Hours(-23 to 23) Minutes(0-59)>
Tech Tip [UTC 0 0]: PST -8 0
The IP address assigned 1.1.1.1 to SM/0 is arbitrary in this design and

only locally significant to the host router.

Step 6: Configure management interface, IP address, and default gateway. Step 10: Verify configuration settings.
Parameter Configured Value
This design uses the external interface as the management interface.
1. Interception Method WCCP
No. Interface Name IP Address Network Mask 2. Time Zone PST -8 0
3. Management Interface GigabitEthernet 2/0
1. GigabitEthernet 1/0 unassigned unassigned (external)
(internal) 4. Autosense Enabled
2. GigabitEthernet 2/0 dhcp 5. DHCP Disabled
(external) IP Address 10.5.52.8
Select Management Interface [1]: 2 IP Network Mask 255.255.255.0
Enable Autosense for Management Interface? (y/n)[y]: y IP Default Gateway 10.5.52.1
Enable DHCP for Management Interface? (y/n)[y]: n 6. CM IP Address 10.4.200.100
Note: You may receive the following warning. This warning may be disre- 8. Domain Name(s) cisco.local
garded as the IP address configuration was provided previously. 9. Host Name bn-br203-wae-sre-1
10. NTP Server Address 10.4.200.17
11. WCCP Router List 10.5.48.253 10.5.48.254
*** You have chosen to disable DHCP! Any network configuration
12. License Enterprise
learnt from DHCPserver will be unlearnt! SETUP will indicate
ESC Quit ? Help ! CLI ────────── WAAS Final Configuration
failure as the managementinterface cannot be brought up
────────────
- Please make sure WAE Management Interface IPaddress and
Press ‘y’ to select configuration, <F2> to see all
Default Gateway are configured from the Router; Press ENTER to
configuration, ‘d’ to toggle defaults display, <1-12> to change
continue:
specific parameter [y]: y
Enter Central Manager IP Address (WARNING: An invalid entry
will cause SETUP to take a long time when applying WAAS Router WCCP configuration
configuration) [None]: 10.4.200.100 First WCCP router IP in the WCCP router list seems to be an
external address; WCCP configuration on external routers is
not allowed through SETUP. Please press ENTER to apply WAAS
Step 7: Configure DNS, host, and NTP settings. configuration on WAE ...
Enter Domain Name Server IP Address [Not configured]:
10.4.200.10 Applying WAAS configuration on WAE ...
Enter Domain Name(s) (Not configured): cisco.local May take a few seconds to complete ...
Enter Host Name (None): bn-br203-wae-sre-1
Enter NTP Server IP Address [None]: 10.4.200.17 WAAS configuration applied successfully!!
Saved configuration to memory.
Step 8: Configure WCCP router list.
Press ENTER to continue ...
Enter WCCP Router (max 4) IP Address list (ip1 ip2 ...) []:
10.5.48.253 10.5.48.254 NOTE: You will be prompted with a recommended router WCCP configura-
tion template. This router configuration is covered in depth in a following
Step 9: Select appropriate license. procedure, so you do not need to retain this information.
The product supports the following licenses:
1. Transport When this configuration is complete, you can return the session to the com-
2. Enterprise mand line of the host router by entering the escape sequence Ctrl-Shift-6 x.
3. Enterprise & Video
Enter the license(s) you purchased [2]: 2
Step 11: Configure GRE negotiated return.

All WAE devices use GRE-negotiated return with their respective WCCP
router(s):
egress-method negotiated-return intercept-method wccp
Step 12: Configure WCCP router list.

The setup script generated a router-list based on the information provided.
To view the device configuration, enter the following command:
bn-br203-wae-sre-1# show running-config | include wccp router-
list
wccp router-list 8 10.5.48.253 10.5.48.254
Router list 8 is specifically for use with WCCP configured on a default gate-
way router. This design uses GRE-negotiated return and router loopback
addresses so we need to create a new router list and delete router list 8.
All WAE configurations in this design use router list 1.
no wccp router-list 8 10.5.48.253 10.5.48.254
wccp router-list 1 10.5.48.253 10.5.48.254
This design uses authentication between the routers and the WAEs.
wccp tcp-promiscuous router-list-num 1 password c1sco123 Procedure 5 Configure Remote Switch for WAE Devices
Step 13: Enable SSH. If you are using a remote-site distribution-layer design, the distribution
switch is the appropriate location to physically connect the WAE devices.
Enabling SSH requires the generation of the RSA key and enabling of the This device type requires a resilient connection, but does not require a rout-
sshd service: ing protocol. This type of connection can use a Layer 2 EtherChannel link.
ssh-key-generate key-length 2048
sshd version 2 This guide assumes that the distribution layer switch has already been
sshd enable configured. Only the procedures required to complete the connection of the
switch to the WAE appliances are included. Full details on distribution layer
Step 14: Save the configuration. switch configuration are included in the Cisco SBA for Large Agencies—
Borderless Networks LAN Deployment Guide.
After making configuration changes through the console, save the
configuration. This design locates the WAE devices on the data (primary) VLAN. It is
copy running-config startup-config required to create a VLAN and SVI for this VLAN if it does not already exist.
Procedure Steps:
Each WAE registers with the WAAS Central Manager as they become active 1. On the WAN distribution switch, create the VLAN and SVI.
on the network. You can verify this registration using the show cms info
command on the respective WAE or via the web interface to the WCM. 2. On the WAN distribution switch, configure Layer 2 EtherChannel links
for the devices and associate them with the VLAN.

Step 1: Create the VLAN and SVI (if necessary).
vlan [VLAN number] Procedure 6 Configure WCCPv2 on Routers
name [VLAN name]
interface Vlan [VLAN number] WCCP is used in this design to divert network traffic destined for the WAN
ip address [IP address] [netmask] to the WAAS system for optimization. This method provides for a clean
deployment with minimal additional cabling, and requires both the WAN-
aggregation and remote-site routers to be configured for WCCP.
Step 2: Configure Layer 2 EtherChannel links for the devices and associate
them with the VLAN. Procedure Steps:
interface Port-channel [number]
1. Configure global WCCP parameters and enable services 61 and 62.
2. Configure WCCP redirect on the LAN and WAN interfaces.
channel-group [number] mode on Step 1: Configure global WCCP parameters and enable services 61 and 62.
no shutdown Services 61 and 62 must be enabled for WCCP redirect for WAAS. These
!
services should be using WCCP Version 2. As a best practice, exempt
switchport access vlan [VLAN number] certain critical traffic types from WCCP redirect by using a redirect list.
channel-group [number] mode on To prevent unauthorized WAE devices from joining the WAAS cluster, you
no shutdown should configure a group-list and password.
ip wccp version 2
Procedure 5 Example ip wccp 61 redirect-list [redirect ACL] group-list [group ACL]
vlan 100 password [password]
name Data ip wccp 62 redirect-list [redirect ACL] group-list [group ACL]
password [password]
description bn-wae-1 EtherChannel ip access-list standard [group ACL]
switchport access VLAN 100 permit [WAAS cluster member IP]
permit [WAAS cluster member IP]
description bn-wae-1 port 1 ip access-list extended [redirect ACL]
switchport access VLAN 100 deny tcp [src IP address] [dest IP address] any eq [TCP
channel-group 7 mode on port]
no shutdown deny tcp [src IP address] [dest IP address] any eq [TCP
! port]
interface GigabitEthernet2/0/3 <additional lines as necessary>
description bn-wae-1 port 2 deny tcp [src IP address] [dest IP address] any eq [TCP
switchport access VLAN 100 port]
channel-group 7 mode on permit tcp any any
no shutdown
!
interface Vlan100
ip address 10.5.1.1 255.255.255.0

Step 2: Configure WCCP redirect on the LAN and WAN interfaces.
Specific interfaces must be identified where traffic to and from the WAN are
intercepted.
Traffic from the LAN is intercepted with service 61 inbound on all LAN
interfaces. It is not necessary to configure WCCP interception on voice
interfaces and voice VLANs.
ip wccp 61 redirect in
Traffic from the WAN is intercepted with service 62 inbound on all WAN inter-
faces, including DMVPN tunnel interfaces (but not their underlying physical
interfaces).
Procedure 6 Example
ip wccp version 2
ip wccp 61 redirect-list WAAS-REDIRECT-LIST group-list BN-WAE
password c1sco123
ip wccp 62 redirect-list WAAS-REDIRECT-LIST group-list BN-WAE
password c1sco123
!
!
ip access-list standard BN-WAE

permit 10.4.128.161
permit 10.4.128.162
ip access-list extended WAAS-REDIRECT-LIST

remark WAAS WCCP Mgmt Redirect List
deny tcp any any eq 22
deny tcp any eq 22 any
deny tcp any eq telnet any
deny tcp any any eq telnet
deny tcp any eq bgp any
deny tcp any any eq bgp
deny tcp any any eq 123
deny tcp any eq 123 any
permit tcp any any

Large Agencies WAN Deployment Product List
Functional Area Product Part Numbers Software Version
WAN 500 Design
WAN Aggregation: ASR1002 Router ASR1002 IOS XE 3.1.0S
MPLS CE Router
SASR1R1-AISK9-26SR asr1000rp1-advipservicesk9.03.01.00.S.150-1.S.bin
ASR1002-PWR-AC
ASR1000-ESP5
WAN Aggregation: DMVPN ASR1002 Router ASR1002 IOS XE 3.1.0S
Hub Router
SASR1R1-AISK9-26SR asr1000rp1-advipservicesk9.03.01.00.S.150-1.S.bin
FLASR1-IPSEC-RTU
ASR1002-PWR-AC
ASR1000-ESP5
WAN Aggregation: WAAS WAVE-574 WAAS Appliance WAVE-574-K9 4.2.1 (WAAS-UNIVERSAL-K9) Build b38
Central Manager
WAAS-ENT-APL oe574-4.2.1.38
WAN Aggregation: WAAS WAE-7371-K9 WAAS Appliance WAE-7371-K9 4.2.1 (WAAS-UNIVERSAL-K9) Build b38
Application Accelerator
SF-WAAS-4.2-SAS-K9 oe7371-4.2.1.38
WAAS-ENT-APL
WAN 100 Design
WAN Aggregation: Cisco3945E CISCO3945E/K9 15.1(1)T
MPLS CE Router
SL-39-DATA-K9 c3900e-universalk9-mz.SPA.151-1.T.bin
C3900-SPE250/K9
PWR-3900-AC
WAN Aggregation: DMVPN Cisco3945E CISCO3945E-SEC/K9 15.1(1)T
Hub Router
SL-39-DATA-K9 c3900e-universalk9-mz.SPA.151-1.T.bin
C3900-SPE250/K9
PWR-3900-AC
WAN Aggregation: WAVE-574 WAAS Appliance WAVE-574-K9 4.2.1 (WAAS-UNIVERSAL-K9) Build b38
WAAS Central Manager
WAAS-ENT-APL oe574-4.2.1.38
Large Agencies WAN Deployment Product List 96

WAN Aggregation: WAAS WAE-7341-K9 WAAS Appliance WAE-7341-K9 4.2.1 (WAAS-UNIVERSAL-K9) Build b38
Application Accelerator
SF-WAAS-4.2-SAS-K9 oe7341-4.2.1.38
WAAS-ENT-APL
WAN Remote Site Routers
MPLS CE Router Cisco2911 CISCO2911-VSEC/K9 15.0(1)M2
DMVPN Spoke Router SL-29-DATA-K9 c2900-universalk9-mz.SPA.150-1.M2.bin
PWR-2911-AC
MPLS CE Router Cisco2921 CISCO2921-VSEC/K9 15.0(1)M2
PWR-2921-AC
MPLS CE Router Cisco3925 C3925-VSEC/K9 15.0(1)M2
PWR-3900-AC
MPLS CE Router Cisco3945 C3945-VSEC/K9 15.0(1)M2
PWR-3900-AC
WAN Remote Site WAAS
Application Accelerator NME-WAE-502 NME-WAE-502-K9 4.2.1 (WAAS-UNIVERSAL-K9) Build b38
Network Module for SM-NM-ADPTR nme-wae-502-4.2.1.38
ISR-G2
WAAS-ENT-NM
Application Accelerator SM-SRE-700-K9 SM-SRE-700-K9 4.2.1 (WAAS-UNIVERSAL-K9) Build b38
Service Module for ISR-G2 WAAS-ENT-NM sm-wae-4.2.1.38
Application Accelerator WAVE-574 WAVE-574-K9 4.2.1 (WAAS-UNIVERSAL-K9) Build b38
WAVE-574 Appliance WAAS-ENT-APL oe574-4.2.1.38
Application Accelerator WAE-674 WAE-674-K9 4.2.1 (WAAS-UNIVERSAL-K9) Build b38
WAE-674 Appliance WAAS-ENT-APL oe674-4.2.1.38

LAN Switching
Distribution Layer Catalyst 3750G WS-C3750G-12S-S 12.2(53)SE1
Stackable 12 Port SFP Catalyst 3750 12 SFP + IPS Image c3750e-universalk9-mz.122-53.SE1.bin
CAB-STACK-50CM
Distribution Layer Catalyst 4507RE WS-C4507R-E 12.2-53.SG1
Dual Supervisors Catalyst 4500 E-Series 7-Slot Chassis cat4500e-entservicesk9-mz.122-53.SG1.bin
Dual Power Supplies WS-X45-SUP6-E
Catalyst 4500 E-Series Sup 6-E, 2x10GE(X2)
with Twin Gig
WS-X4624-SFP-E
Catalyst 4500 E-Series 24-Port GE (SFP)
WS-X4606-X2-E
Catalyst 4500 E-Series 6-Port 10GbE (X2)
Distribution Layer Catalyst 6500 VSS WS-C6506-E 12.2(33) SXI3 with the IP Services Feature Set
Catalyst 6500 E-Series 6-Slot Chassis s72033-ipservicesk9_wan-mz.122-33.SXI3.bin
VS-S720-10G-3C
Catalyst 6500 VSS Supervisor 720 with 2
ports 10GbE
WS-X6724-SFP
Catalyst 6500 24-port GigE Mod (SFP)
WS-X6716-10G-3C
Catalyst 6500 16 port 10 Gigabit Ethernet w/
DFC3C (X2)

Appendix A:
Figure 33. IPsec Tunnel
Technical Feature
Supplement
Front Door VRF for DMVPN

Building an IPsec tunnel requires reachability between the crypto routers.
When you use the Internet, routers use a default route to contact their peers
as shown in Figure 33.
Appendix A: Technical Feature Supplement 99

If you need to extend the internal network (and the same default routing Figure 35. IPsec Tunnel with F-VRF Aggregation
options that are available to internal users), then a default route must be
advertised to the VPN hub router. See Figure 34A.
Figure 34. IPsec Tunnel Before/After Default Route Injection
A B
This configuration is referred to as Front Door VRF (F-VRF), because the

Internet is contained in a VRF. The alternative to this design is Inside VRF
A B (I-VRF), where the internal network is in a VRF on the VPN hub and the
Internet remains in the global VRF. This method is not documented in
The advertisement of a default route to the hub router (with an existing
this guide.
default route) is problematic. This route requires a better administrative
distance to become the active default, which then overrides the default It is now possible to reestablish the IPSec tunnel to the remote peer router.
route that is supporting the peer-peer IPsec tunnel connection. This routing As the remote-site policy requires central Internet access for end users, a
advertisement breaks the tunnel as shown in Figure 34B. default route is advertised through the tunnel. This advertisement causes a
similar default routing issue on the remote router; the tunnel default overrides
Through the introduction of an external VRF INET-PUBLIC (shown in red), the
the Internet-pointing default and the tunnel connection breaks as shown in
hub router can support multiple default routes. The internal network remains
Figure 35B.
in the global VRF. This is shown in Figure 35A.
Tech Tip
Most additional features on the hub router do not require

VRF-awareness.

This configuration requires using F-VRF on the remote-site router as well. Figure 36. Front Door VRF—Final Configuration
The primary benefits of using this solution are as follows:
• Simplified default routing and static default routes in the INET-PUBLIC
VRFs
• Ability to support default routing for end-users traffic through VPN
tunnels
• Ability to leverage dynamic default routing for sites with multiple WAN
transports
• Ability to build spoke-to-spoke tunnels with DMVPN with end-user traffic
routed by default through VPN tunnels
The final design that uses F-VRF at both the WAN-aggregation site and a
WAN remote site is shown in Figure 36.

Appendix B:
SBA for Large Agencies Document System
Design Guides Deployment Guides Supplemental Guides
Foundation Deployment Wireless CleanAir

Design Overview
Guides Deployment Guide
IPv6 Addressing LAN Deployment Nexus 7000

Guide Guide Deployment Guide
LAN SIEM Deployment

Configuration Guide Guide
WAN Deployment ArcSight SIEM

You are Here
Guide Partner Guide
WAN LogLogic SIEM

Configuration Guide Partner Guide
Internet Edge nFx SIEM

Deployment Guide Partner Guide
Internet Edge RSA SIEM

Configuration Guide Partner Guide
Network Management Splunk SIEM

Guides Partner Guide
SolarWinds Data Security

Deployment Guide Deployment Guide
CREDANT Data Security

Partner Guide
Lumension Data Security

Partner Guide
Appendix B: SBA for Large Agencies Document System 102

Americas Headquarters Asia Pacific Headquarters Europe Headquarters
Cisco Systems, Inc. Cisco Systems (USA) Pte. Ltd. Cisco Systems International BV
San Jose, CA Singapore Amsterdam, The Netherlands
Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the Cisco Website at www.cisco.com/go/offices.
Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word
partner does not imply a partnership relationship between Cisco and any other company. (1005R)
C07-641107-00 12/10
103

DMVPN & MPLS

Uploaded by

Copyright:

Available Formats

DMVPN & MPLS

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DMVPN & MPLS

Uploaded by

Copyright:

Available Formats

WAN Deployment

this Document • Has up to 500 remote sites

Design Guides Deployment Guides

WAN Configuration Guide

Using this Borderless Networks Guide 2

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Deploying the WAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

WAN Application Firewall Internet

Branch Router with

WAN500 Design Architecture Overview 6

The WAN500 Design is shown in Figure 3. Figure 4. WAN Remote-Site Designs

Figure 3. WAN500 Design

The remote-site designs include single or dual WAN edge routers.

WAN Remote- WAN Primary Secondary WAN Remote-Site

(dual router only)

Path Selection Preferences

Deploying the WAN 14

Network Service IP Address

Deploying the WAN 15

Deploying the WAN 16

2911 2921 3925 3945

Deploying the WAN 17

Deploying the WAN 18

Deploying the WAN 19

Process Step 3: Configure device-management protocols.

Enabling SSH requires that a public/private keypair be generated for the

Allow only SSH access to the device:

Deploying the WAN 20

Step 4: Configure secure user authentication. Procedure 2 Connect to Distribution Switch

Authentication, authorization and accounting (AAA) is enabled for access

Deploying the WAN 21

Deploying the WAN 22

router eigrp 100

Deploying the WAN 23

Step 1: Enable BGP.

Deploying the WAN 24

Step 1: Enable IP multicast routing. Process

Deploying the WAN 25

Procedure Steps: Procedure 3 Connect to Core

1. Configure the port-channel interface and assign the IP address.

Deploying the WAN 26

Deploying the WAN 27

Deploying the WAN 28

Remote-Site MPLS CE Router Configuration

Deploying the WAN 29

Step 5: Configure a synchronized clock.

Deploying the WAN 30

Procedure Steps: Procedure 3 Configure BGP

1. Assign the interface bandwidth.

Deploying the WAN 31

Deploying the WAN 32

Deploying the WAN 33

Deploying the WAN 34

Deploying the WAN 35

Deploying the WAN 36

Deploying the WAN 37

2911 2921 3925 3945

Deploying the WAN 38

VRFs and Front Door VRF

Deploying the WAN 39

Deploying the WAN 40

Procedure 3 Configure the Transit Network