Hukseflux

Thermal Sensors

USER MANUAL SR20

Secondary standard pyranometer

Copyright by Hukseflux | manual v1814 | www.hukseflux.com | info@hukseflux.com

Warning statements

Putting more than 12 Volt across the sensor wiring

can lead to permanent damage to the sensor.

Do not use “open circuit detection” when measuring

the sensor output.

SR20 manual v1814 2/43

Contents
Warning statements 2
Contents 3
List of symbols 4
Introduction 5
1 Ordering and checking at delivery 7
1.1 Ordering SR20 7
1.2 Included items 7
1.3 Quick instrument check 8
2 Instrument principle and theory 9
3 Specifications of SR20 12
3.1 Specifications of SR20 12
3.2 Dimensions of SR20 15
4 Standards and recommended practices for use 16
4.1 Classification standard 16
4.2 General use for solar radiation measurement 16
4.3 General use for sunshine duration measurement 16
4.4 Specific use for outdoor PV system performance testing 17
4.5 Specific use in meteorology and climatology 17
5 Installation of SR20 18
5.1 Site selection and installation 18
5.2 Installation of the sun screen 19
5.3 Electrical connection 20
5.4 Requirements for data acquisition / amplification 21
6 Making a dependable measurement 22
6.1 The concept of dependability 22
6.2 Reliability of the measurement 23
6.3 Speed of repair and maintenance 24
6.4 Uncertainty evaluation 24
7 Maintenance and trouble shooting 27
7.1 Recommended maintenance and quality assurance 27
7.2 Trouble shooting 28
7.3 Calibration and checks in the field 29
7.4 Data quality assurance 30
8 Appendices 32
8.1 Appendix on cable extension / replacement 32
8.2 Appendix on tools for SR20 33
8.3 Appendix on spare parts for SR20 33
8.4 Appendix on standards for classification and calibration 34
8.5 Appendix on calibration hierarchy 35
8.6 Appendix on meteorological radiation quantities 36
8.7 Appendix on ISO and WMO classification tables 37
8.8 Appendix on definition of pyranometer specifications 38
8.9 Appendix on terminology / glossary 39
8.10 Appendix on converting resistance to temperature 40
8.11 EU declaration of conformity 41

SR20 manual v1814 3/43

List of symbols
Quantities Symbol Unit

Voltage output U V
Sensitivity S V/(W/m2)
Sensitivity at reference conditions S0 V/(W/m2)
Temperature T °C
Electrical resistance Re Ω
Solar irradiance E W/m2
Solar radiant exposure H W∙h/m2
Time in hours h h

Temperature coefficient a 1/°C²

Temperature coefficient b 1/°C
Temperature coefficient c -

Resistance of Pt100 RPt100 Ω

Pt100 coefficient A
Pt100 coefficient B

Resistance of 10 kΩ thermistor Rthermistor Ω

Steinhart-Hart coefficient α
Steinhart-Hart coefficient β
Steinhart-Hart coefficient γ

(see also appendix 8.6 on meteorological quantities)

Subscripts

Not applicable

SR20 manual v1814 4/43

Introduction
SR20 is a solar radiation sensor of the highest category in the ISO 9060 classification
system: secondary standard. SR20 pyranometer should be used where the highest
measurement accuracy is required.

SR20 measures the solar radiation received by a plane surface, in W/m2, from a 180o
field of view angle. SR20 enables you to attain the highest measurement accuracy and
excels in demanding applications.
The measured quantity, expressed in W/m2, is called “hemispherical” solar radiation.
SR20 pyranometer can be employed outdoors under the sun, as well as indoors with
lamp-based solar simulators. Its orientation depends on the application and may be
horizontal, tilted (for plane of array radiation) or inverted (for reflected radiation). In
combination with the right software, also sunshine duration may be measured.

Using SR20 is easy. It can be connected directly to commonly used data logging
systems. The irradiance, E, in W/m2 is calculated by dividing the SR20 output, a small
voltage U, by the sensitivity S. The sensitivity is provided with SR20 on its calibration
certificate.

The central equation governing SR20 is: E = U/S (Formula 0.1)

SR20’s low temperature dependence makes it an ideal candidate for use under very cold
and very hot conditions. The temperature dependence of every individual instrument is
tested and supplied as a second degree polynomial. This information can be used for
further reduction of temperature dependence during post-processing. In case the
sensitivity is corrected for the instrument body temperature, the optional measurement
equation becomes:

E = U/(S0·(a·T² + b·T +c)) (Formula 0.2)

The temperature coefficients a, b, and c can be found on the calibration certificate of

each instrument.

SR20 is equipped with an internal temperature sensor. This can be either a Pt100 (T1
version) or a 10 kΩ thermistor (T2 version), as ordered. To calculate temperature in
degrees Celsius from resistance in Ohms, Formula 8.10.1 or 8.10.2 can be used. See the
dedicated chapter in the appendix of this manual for these equations.

The incorporated heater reduces measurement errors caused by early-morning dew

deposition. The instrument should be used in accordance with the recommended
practices of ISO, WMO and ASTM.

SR20 manual v1814 5/43

Figure 0.1 SR20 secondary standard pyranometer with its sun screen removed

Suggested use for SR20:

• PV system performance monitoring

• scientific meteorological observations
• reference instrument for comparison
• extreme climates (tropical / polar)
• sunshine duration measurement

The ASTM E2848 “Standard Test Method for Reporting Photovoltaic Non-Concentrator
System Performance” (issued end 2011) confirms that a pyranometer is the preferred
instrument for PV system performance monitoring. SR20 pyranometer complies with the
requirements of this standard. For more information see our pyranometer selection
guide.

WMO has approved the “pyranometric method” to calculate sunshine duration from
pyranometer measurements in WMO-No. 8, Guide to Meteorological Instruments and
Methods of Observation. This implies that SR20 may be used, in combination with
appropriate software, to estimate sunshine duration. This is much more cost-effective
than using a dedicated sunshine duration sensor. Ask for our application note.

SR20’s output is analogue. Model SR20-D2 offers two other types of commonly used
irradiance outputs: digital via Modbus RTU over 2-wire RS-485 and analogue 4-20 mA
output (current loop).

This user manual covers SR20 use. Specifications of model SR20-D2, the digital
secondary standard pyranometer with Modbus RTU and 4-20 mA output, differ
from those of SR20. For SR20-D2 use, please consult the SR20-D2 user manual.

SR20 manual v1814 6/43

1 Ordering and checking at delivery
1.1 Ordering SR20

The standard configuration of SR20 is with 5 metres cable.

Common options are:

• Longer cable (in multiples of 5 m). Specify total cable length.

• Internal temperature sensor. This can be either a Pt100 or a 10 kΩ thermistor.
Specify respectively T1 or T2.
• Five silica gel bags in an air-tight bag for SR20 desiccant holder. Specify order
number DC01.
• VU01 ventilation unit.

1.2 Included items

Arriving at the customer, the delivery should include:

• pyranometer SR20
• sun screen
• cable of the length as ordered
• calibration certificate matching the instrument serial number
• product certificate matching the instrument serial number (including temperature
response and directional response test)
• any other options as ordered

Please store the certificates in a safe place.

SR20 manual v1814 7/43

1.3 Quick instrument check

A quick test of the instrument can be done by using a simple hand held multimeter and a
lamp.

1. Check the electrical resistance of the sensor between the green (-) and white (+) wire.
Use a multimeter at the 1000 Ω range. Measure the sensor resistance first with one
polarity, than reverse the polarity. Take the average value. The typical resistance of the
wiring is 0.1 Ω/m. Typical resistance should be the typical sensor resistance of 100 to
200 Ω plus 1.5 Ω for the total resistance of two wires (back and forth) of each 5 m.
Infinite resistance indicates a broken circuit; zero or a low resistance indicates a short
circuit.
2. Check if the sensor reacts to light: put the multimeter at its most sensitive range of
DC voltage measurement, typically the 100 x 10-3 VDC range or lower. Expose the sensor
to a strong light source, for instance a 100 W light bulb at 0.1 m distance. The signal
should read > 2 x 10-3 V now. Darken the sensor either by putting something over it or
switching off the light. The instrument voltage output should go down and within one
minute approach 0 V.
3. Remove the sun screen, (see chapter on installation of the sun screen). Inspect the
bubble level.
4. Inspect the instrument for any damage.
5. Inspect if the humidity indicator is blue. Blue indicates dryness. The colour pink
indicates it is humid: in the latter case replace the desiccant (see chapter on
maintenance).

SR20 manual v1814 8/43

2 Instrument principle and theory

3 4
5

11
8
10 9

Figure 2.1 Overview of SR20:

(1) cable (standard length 5 metres, optional longer cable)

(2) fixation of sun screen (thumb screw)
(3) inner dome
(4) thermal sensor with black coating
(5) outer dome
(6) sun screen
(7) humidity indicator
(8) desiccant holder
(9) levelling feet
(10) bubble level
(11) connector

SR20 manual v1814 9/43

SR20’s scientific name is pyranometer. A pyranometer measures the solar radiation
received by a plane surface from a 180 ° field of view angle. This quantity, expressed in
W/m2, is called “hemispherical” solar radiation. The solar radiation spectrum extends
roughly from 285 to 3000 x 10-9 m. By definition a pyranometer should cover that
spectral range with a spectral selectivity that is as “flat” as possible.

In an irradiance measurement by definition the response to “beam” radiation varies with

the cosine of the angle of incidence; i.e. it should have full response when the solar
radiation hits the sensor perpendicularly (normal to the surface, sun at zenith, 0 ° angle
of incidence), zero response when the sun is at the horizon (90 ° angle of incidence, 90 °
zenith angle), and 50 % of full response at 60 ° angle of incidence.
A pyranometer should have a so-called “directional response” (older documents mention
“cosine response”) that is as close as possible to the ideal cosine characteristic.

In order to attain the proper directional and spectral characteristics, a pyranometer’s

main components are:

• a thermal sensor with black coating. It has a flat spectrum covering the 200 to 50000
x 10-9 m range, and has a near-perfect directional response. The coating absorbs all
solar radiation and, at the moment of absorption, converts it to heat. The heat flows
through the sensor to the sensor body. The thermopile sensor generates a voltage
output signal that is proportional to the solar irradiance.

• a glass dome. This dome limits the spectral range from 285 to 3000 x 10-9 m (cutting
off the part above 3000 x 10-9 m), while preserving the 180 ° field of view angle.
Another function of the dome is that it shields the thermopile sensor from the
environment (convection, rain).

• a second (inner) glass dome: For a secondary standard pyranometer, two domes are
used, and not one single dome. This construction provides an additional “radiation
shield”, resulting in a better thermal equilibrium between the sensor and inner dome,
compared to using a single dome. The effect of having a second dome is a strong
reduction of instrument offsets.

Pyranometers can be manufactured to different specifications and with different levels of

verification and characterisation during production. The ISO 9060 - 1990 standard, “Solar
energy - specification and classification of instruments for measuring hemispherical solar
and direct solar radiation”, distinguishes between 3 classes; secondary standard (highest
accuracy), first class (second highest accuracy) and second class (third highest
accuracy).

From second class to first class and from first class to secondary standard, the achievable
accuracy improves by a factor 2.

SR20 manual v1814 10/43

 1,2
response [arbitrary units]
relative spectral content /

1 solar radiation

0,8
pyranometer
response
0,6

0,4

0,2

0
100 1000 10000

wavelength [x 10-9 m]

Figure 2.2 Spectral response of the pyranometer compared to the solar spectrum. The
pyranometer only cuts off a negligible part of the total solar spectrum.

4%

North
Deviation from ideal cosine behaviour [%]

2%
East

South
0%
0 20 40 60 80

West

-2%

ISO secondary
standard
directional
response limit
-4%

zenith angle [°]

Figure 2.3 Directional response of a SR20 pyranometer of 4 azimuth angles, compared

to secondary standard limits

SR20 manual v1814 11/43

3 Specifications of SR20
3.1 Specifications of SR20

SR20 is a pyranometer of the highest category in the ISO 9060 classification system:
secondary standard. It measures the solar radiation received by a plane surface from a
180o field of view angle. This quantity, expressed in W/m2, is called “hemispherical” solar
radiation. Working completely passive, using a thermopile sensor, SR20 generates a
small output voltage proportional to this flux. It can only be used in combination with a
suitable measurement system.

SR20 has an onboard heater and a temperature sensor. Heating the sensor, measuring
the body temperature and using the correction of the temperature response, all
contribute to the dependability and accuracy of the measurement. However, also when
not using these features, SR20 still complies with the secondary standard requirements.
The instrument should be used in accordance with the recommended practices of ISO,
IEC, WMO and ASTM.

Table 3.1.1 Specifications of SR20 (continued on next pages)

SR20 MEASUREMENT SPECIFICATIONS:

LIST OF CLASSIFICATION CRITERIA OF ISO 9060*

ISO classification (ISO 9060: 1990) secondary standard pyranometer

WMO performance level (WMO-No. 8, high quality pyranometer
seventh edition 2008)
Response time (95 %) 4.5 s
Zero offset a (response to 200 W/m2 5 W/m2 unventilated
net thermal radiation) 2.5 W/m2 ventilated
Zero offset b (response to 5 K/h < ± 2 W/m2
change in ambient temperature)
Non-stability < ± 0.5 % change per year
Non-linearity < ± 0.2 % (100 to 1000 W/m2)
Directional response < ± 10 W/m2
Directional response test of individual report included
instrument
Spectral selectivity < ± 3 % (0.35 to 1.5 x 10-6 m)
Temperature response < ± 1 % (-10 to +40 °C)
< ± 0.4 % (-30 to +50 °C) with correction in data-
processing
Temperature response of individual report included
instrument
Tilt response < ± 0.2 % (0 to 90 ° at 1000 W/m2)

*For the exact definition of pyranometer ISO 9060 specifications see the appendix.

SR20 manual v1814 12/43

Table 3.1.1 Specifications of SR20 (continued)

SR20 ADDITIONAL SPECIFICATIONS

Measurand hemispherical solar radiation

Measurand in SI radiometry units irradiance in W/m2
Optional measurand sunshine duration
Field of view angle 180 °
Measurement range 0 to 4000 W/m2
Sensitivity range 7 to 25 x 10-6 V/(W/m2)
Sensitivity (nominal) 15 x 10-6 V/(W/m2)
Expected voltage output application under natural solar radiation: -0.1 to + 50
x 10-3 V
Measurement function / required E = U/S
programming
Optional measurement function / E = U/(S0·(a·T²+b·T+c))
required programming for correction of
sensitivity as a function of instrument
body temperature
Measurement function / optional programming according to WMO guide paragraph
programming for sunshine duration 8.2.2
Required readout 1 differential voltage channel or 1 single ended
voltage channel, input resistance > 106 Ω
Internal temperature sensor measuring the body temperature:
version code = T1 for Pt100 DIN class A,
version code = T2 for thermistor 10 kΩ at 25 °C
Optional readout 1 temperature channel in case the temperature sensor
is used
Rated operating temperature range -40 to +80 °C
Sensor resistance range 50 to 100 Ω
Required sensor power zero (passive sensor)
Spectral range 285 to 3000 x 10-9 m
(20 % transmission points)
Standard governing use of the ISO/TR 9901:1990 Solar energy -- Field pyranometers
instrument -- Recommended practice for use
ASTM G183 - 05 Standard Practice for Field Use of
Pyranometers, Pyrheliometers and UV Radiometers
Standard cable length (see options) 5m
Cable diameter 5.3 x 10-3 m
Chassis connector M16 panel connector, male thread, 10-pole
Chassis connector type HUMMEL AG 7.840.200.000 panel connector, front
mounting, short version
Cable connector M16 straight connector, female thread, 10-pole
Cable connector type HUMMEL AG 7.810.300.00M straight connector,
female thread, for cable 3 to 6 x 10-3 m, special
version
Connector protection class IP67 / IP69 K per EN 60 529 (connected)
Cable replacement replacement cables with connector can be ordered
separately from Hukseflux
Mounting 2 x M5 bolt at 65 x 10-3 m centre-to-centre distance
on north-south axis, or 1 x M6 bolt at the centre of
the instrument, connection from below under the
bottom plate of the instrument
Levelling bubble level and adjustable levelling feet are included
Levelling accuracy < 0.1° bubble entirely in ring
Desiccant two bags of silica gel, 0.5 g, 35 x 20 mm
Humidity indicator blue when dry, pink when humid
IP protection class IP67

SR20 manual v1814 13/43

Table 3.1.1 Specifications of SR20 (started on previous pages)

Gross weight including 5 m cable 1.2 kg

Net weight including 5 m cable 0.85 kg
Packaging box of 200 x 135 x 225 mm
HEATING

Heater operation the heater is not necessarily switched on;

recommended operation is to activate the heater
when the sun is below the horizon
Required heater power 1.5 W at 12 VDC (the heater is not necessarily active)
Heater resistance 95 Ω
Steady state zero offset caused by 0 to -8 W/m2
heating
CALIBRATION

Calibration traceability to WRR

Calibration hierarchy from WRR through ISO 9846 and ISO 9847, applying
a correction to reference conditions
Calibration method indoor calibration according to ISO 9847, Type IIc
Calibration uncertainty < 1.2 % (k = 2)
Recommended recalibration interval 2 years
Reference conditions 20 °C, normal incidence solar radiation, horizontal
mounting, irradiance level 1000 W/m2
Validity of calibration based on experience the instrument sensitivity will not
change during storage. During use under exposure to
solar radiation the instrument “non-stability”
specification is applicable.
MEASUREMENT ACCURACY

Uncertainty of the measurement statements about the overall measurement

uncertainty can only be made on an individual basis.
See the chapter on uncertainty evaluation
WMO estimate on achievable accuracy 2%
for daily sums (see appendix for a
definition of the measurement conditions)
WMO estimate on achievable accuracy 3%
for hourly sums (see appendix for a
definition of the measurement conditions)
VERSIONS / OPTIONS

Digital output via Modbus RTU protocol option code = D2

and 4-20 mA output (current loop) for specifications see the SR20-D2 user manual
Longer cable, in multiples of 5 m option code = total cable length
ACCESSORIES

Ventilation unit VU01

Separate amplifiers AC100 and AC420
Hand-held read-out unit LI19
Bags of silica gel for desiccant set of 5 bags in an air tight bag
option code = DC01

SR20 manual v1814 14/43

3.2 Dimensions of SR20

65

Ø 150

M5 (2x) M6
85

Figure 3.2.1 Dimensions of SR20 in x 10-3 m.

SR20 manual v1814 15/43

4 Standards and recommended practices
for use
Pyranometers are classified according to the ISO 9060 standard and the WMO-No. 8
Guide. In any application the instrument should be used in accordance with the
recommended practices of ISO, IEC, WMO and / or ASTM.

4.1 Classification standard

Table 4.1.1 Standards for pyranometer classification. See the appendix for definitions of
pyranometer specifications, and a table listing the specification limits.

STANDARDS FOR INSTRUMENT CLASSIFICATION

ISO STANDARD EQUIVALENT WMO

ASTM STANDARD

ISO 9060:1990 Not available WMO-No. 8; Guide to

Solar energy -- specification and Meteorological Instruments
classification of instruments for and Methods of Observation,
measuring hemispherical solar and chapter 7, measurement of
direct solar radiation radiation, 7.3 measurement
of global and diffuse solar
radiation

4.2 General use for solar radiation measurement

Table 4.2.1 Standards with recommendations for instrument use in solar radiation
measurement

STANDARDS FOR INSTRUMENT USE FOR HEMISPHERICAL SOLAR RADIATION

ISO STANDARD EQUIVALENT WMO

ASTM STANDARD

ISO/TR 9901:1990 ASTM G183 - 05 WMO-No. 8; Guide to

Solar energy -- Field Standard Practice for Field Meteorological Instruments
pyranometers -- Recommended Use of Pyranometers, and Methods of Observation,
practice for use Pyrheliometers and UV chapter 7, measurement of
Radiometers radiation, 7.3 measurement
of global and diffuse solar
radiation

4.3 General use for sunshine duration measurement

According to the World Meteorological Organization (WMO, 2003), sunshine duration
during a given period is defined as the sum of that sub-period for which the direct solar
irradiance exceeds 120 W/m2.

SR20 manual v1814 16/43

WMO has approved the “pyranometric method” to estimate sunshine duration from
pyranometer measurements (Chapter 8 of the WMO Guide to Instruments and
Observation, 2008). This implies that a pyranometer may be used, in combination with
appropriate software, to estimate sunshine duration. Ask for our application note.

Table 4.3.1 Standards with recommendations for instrument use in sunshine duration
measurement

STANDARDS FOR INSTRUMENT USE FOR SUNSHINE DURATION

WMO

WMO-No. 8; Guide to Meteorological Instruments and Methods of Observation, chapter 8,

measurement of sunshine duration, 8.2.2 Pyranometric Method

4.4 Specific use for outdoor PV system performance testing

SR20 is very well applicable in outdoor PV system performance testing. See also model
SR20-D2 “digital secondary standard pyranometer with Modbus RTU and 4-20 mA
output” and SR12 “first class pyranometer for solar energy test applications”.

Table 4.4.1 Standards with recommendations for instrument use in PV system

performance testing

STANDARDS ON PV SYSTEM PERFORMANCE TESTING

IEC / ISO STANDARD EQUIVALENT ASTM STANDARD

IEC 61724; Photovoltaic system performance ASTM 2848-11; Standard Test Method for
monitoring – guidelines for measurement, data Reporting Photovoltaic Non-Concentrator
exchange and analysis System Performance

COMMENT: Allows pyranometers or reference COMMENT: confirms that a pyranometer is the

cells according to IEC 60904-2 and -6. preferred instrument for outdoor PV testing.
Pyranometer reading required accuracy better Specifically recommends a “first class”
than 5% of reading (Par 4.1) pyranometer (paragraph A 1.2.1.)

COMMENT: equals JISC 8906 (Japanese

Industrial Standards Committee)

4.5 Specific use in meteorology and climatology

The World Meteorological Organization (WMO) is a specialised agency of the United

Nations. It is the UN system's authoritative voice on the state and behaviour of the
earth's atmosphere and climate. WMO publishes WMO-No. 8; Guide to Meteorological
Instruments and Methods of Observation, in which a table is included on “level of
performance” of pyranometers. Nowadays WMO conforms itself to the ISO classification
system.

SR20 manual v1814 17/43

5 Installation of SR20
5.1 Site selection and installation

Table 5.1.1 Recommendations for installation of pyranometers

Location the situation that shadows are cast on the instruments

is usually not desirable. The horizon should be as free
from obstacles as possible. Ideally there should be no
objects between the course of the sun and the
instrument.

Mechanical mounting / thermal insulation preferably use connection by bolts to the bottom plate
of the instrument. A pyranometer is sensitive to
thermal shocks. Do not mount the instrument with the
body in direct thermal contact to the mounting plate
(so always use the levelling feet also if the mounting
is not horizontal), do not mount the instrument on
objects that become very hot (black coated metal
plates).

Instrument mounting with 2 bolts 2 x M5 bolt at 65 x 10-3 m centre to centre distance

on north-south axis, connection from below under the
bottom plate of the instrument.

Instrument mounting with one bolt 1 x M6 bolt at the centre of the instrument,
connection from below under the bottom plate of the
instrument.

Performing a representative the pyranometer measures the solar radiation in the

measurement plane of the sensor. This may require installation in a
tilted or inverted position. The black sensor surface
(sensor bottom plate) should be mounted parallel to
the plane of interest.
In case a pyranometer is not mounted horizontally or
in case the horizon is obstructed, the
representativeness of the location becomes an
important element of the measurement. See the
chapter on uncertainty evaluation.

Levelling in case of horizontal mounting only use the bubble

level and levelling feet. For inspection of the bubble
level the sun screen must be removed.

Instrument orientation by convention with the cable exit pointing to the

nearest pole (so the cable exit should point north in
the northern hemisphere, south in the southern
hemisphere).

Installation height in case of inverted installation, WMO recommends a

distance of 1.5 m between soil surface and sensor
(reducing the effect of shadows and in order to obtain
good spatial averaging).

SR20 manual v1814 18/43

5.2 Installation of the sun screen

SR20’s sun screen can be installed and removed by using the dedicated thumb screw.
See item 2 of the drawing below. The thumb screw can be turned without tools for
fixation or loosening of the sun screen, as visualised below. Once the thumb screw has
turned the sun screen loose, the screen can be lifted off manually. After removal the user
may inspect the bubble level, item 10 of the drawing, and remove the cable / connector,
item 11.

3 4
5
2

7
11
8
10 9

Figure 5.2.1 Installation and removal of SR20’s sun screen

SR20 manual v1814 19/43

5.3 Electrical connection

In order to operate, a pyranometer should be connected to a measurement system,

typically a so-called datalogger. SR20 is a passive sensor that does not need any power.
Cables generally act as a source of distortion, by picking up capacitive noise. We
recommend keeping the distance between a datalogger or amplifier and the sensor as
short as possible. For cable extension, see the appendix on this subject.

Table 5.3.1 The electrical connection of SR20 versions T1 and T2. The heater is not
necessarily used. The temperature sensor is not necessarily used.

PIN WIRE SR20-T1 SR20-T2

2 Red Pt100 [+] 10 kΩ thermistor [+]

3 Pink Pt100 [+] 10 kΩ thermistor [+]

6 Blue Pt100 [−] 10 kΩ thermistor [−]

8 Grey Pt100 [−] 10 kΩ thermistor [−]

1 Brown heater heater

4 Yellow heater heater

9 Black ground ground

7 White signal [+] signal [+]

5 Green signal [−] signal [−]

Note 1: Pt100’s of version T1 may be connected in a 3-wire of 4-wire configuration.

Note 2: 10k thermistors of version T2 are usually connected in a 2-wire configuration.
Note 3: the heater is not necessarily connected. In case it is connected, the polarity of
the connection is not important.
Note 4: signal wires are insulated from ground wire and from the sensor body. Insulation
resistance is tested during production and larger than 1 x 106 Ω.
Note 5: ground is connected to the connector, the sensor body and the shield of the wire.

Figure 5.3.1 Electrical diagram of the internal wiring of SR20. The shield is connected to
the sensor body.

SR20 manual v1814 20/43

5.4 Requirements for data acquisition / amplification

The selection and programming of dataloggers is the responsibility of the user. Please
contact the supplier of the data acquisition and amplification equipment to see if
directions for use with the SR20 are available.
In case programming for similar instruments is available, this can typically also be used.
SR20 can usually be treated in the same way as other thermopile pyranometers.
Pyranometers usually have the same programming as heat flux sensors.

Table 5.4.1 Requirements for data acquisition and amplification equipment for SR20 in
the standard configuration

Capability to measure small voltage preferably: 5 x 10-6 V uncertainty

signals minimum requirement: 20 x 10-6 V uncertainty
(valid for the entire expected temperature range of the
acquisition / amplification equipment)

Capability for the data logger or the to store data, and to perform division by the sensitivity to
software calculate the solar irradiance.
E = U/S (Formula 0.1)

Data acquisition input resistance > 1 x 106 Ω

Open circuit detection open-circuit detection should not be used, unless this is done
(WARNING) separately from the normal measurement by more than 5
times the sensor response time and with a small current
only. Thermopile sensors are sensitive to the current that is
used during open circuit detection. The current will generate
heat, which is measured and will appear as an offset.

SR20 manual v1814 21/43

6 Making a dependable measurement
6.1 The concept of dependability

A measurement with a pyranometer is called “dependable” if it is reliable, i.e. measuring

within required uncertainty limits, for most of the time and if problems, once they occur,
can be solved quickly.

The requirements for a measurement with a pyranometer may be expressed by the user
as:

• required uncertainty of the measurement (see following paragraphs)

• requirements for maintenance and repairs (possibilities for maintenance and repair
including effort to be made and processing time)
• a requirement to the expected instrument lifetime (until it is no longer feasible to
repair)

It is important to realise that the uncertainty of the measurement is not only determined
by the instrument but also by the way it is used.

See also ISO 9060 note 5. In case of pyranometers, the measurement uncertainty as
obtained during outdoor measurements is a function of:

• the instrument class

• the calibration procedure / uncertainty
• the duration of instrument employment under natural sunlight (involving the
instrument stability specification)
• the measurement conditions (such as tilting, ventilation, shading, instrument
temperature)
• maintenance (mainly fouling)
• the environmental conditions*

Therefore, ISO 9060 says, “statements about the overall measurement uncertainty under
outdoor conditions can only be made on an individual basis, taking all these factors into
account”.

* defined at Hukseflux as all factors outside the instrument that are relevant to the
measurement such as the cloud cover (presence or absence of direct radiation), sun
position, the local horizon (which may be obstructed) or condition of the ground (when
tilted). The environmental conditions also involve the question whether or not the
measurement at the location of measurement is representative of the quantity that
should be measured.

SR20 manual v1814 22/43

6.2 Reliability of the measurement

A measurement is reliable if it measures within required uncertainty limits for most of the
time. We distinguish between two causes of unreliability of the measurement:

• related to the reliability of the pyranometer and its design, manufacturing, calibration
(hardware reliability).
• related to the reliability of the measurement uncertainty (measurement reliability),
which involves hardware reliability as well as condition of use.

Most of the hardware reliability is the responsibility of the instrument manufacturer.

The reliability of the measurement however is a joint responsibility of instrument
manufacturer and user. As a function of user requirements, taking into account
measurement conditions and environmental conditions, the user will select an instrument
of a certain class, and define maintenance support procedures.

In many situations there is a limit to a realistically attainable accuracy level. This is due
to conditions that are beyond control once the measurement system is in place. Typical
limiting conditions are:

• the measurement conditions, for instance when working at extreme temperatures

when the instrument temperature is at the extreme limits of the rated temperature
range.
• the environmental conditions, for instance when installed at a sub-optimal
measurement location with obstacles in the path of the sun.
• other environmental conditions, for instance when assessing PV system performance
and the system contains panels at different tilt angles, the pyranometer
measurement may not be representative of irradiance received by the entire PV
system.

The measurement reliability can be improved by maintenance support. Important aspects

are:

• dome fouling by deposition of dust, dew, rain or snow. Fouling results in undefined
measurement uncertainty (sensitivity and directional error are no longer defined).
This should be solved by regular inspection and cleaning.
• sensor instability. Maximum expected sensor aging is specified per instrument as its
non-stability in [% change / year]. In case the sensor is not recalibrated, the
uncertainty of the sensitivity gradually will increase. This is solved by regular
recalibration.
• moisture condensing under pyranometer domes resulting in a slow change of
sensitivity (within specifications). This is solved by regular replacement of desiccant
or by maintenance (drying the entire sensor) in case the sensor allows this. For non-
serviceable sensors like most second class pyranometers, this may slowly develop
into a defect. For first class and secondary standard models (for instance model SR11
first class pyranometer and SR20 secondary standard pyranometer) extra desiccant
(in a set of 5 bags in an air tight bag) is available.

SR20 manual v1814 23/43

Another way to improve measurement reliability is to introduce redundant sensors.

• the use of redundant instruments allows remote checks of one instrument using the
other as a reference, which leads to a higher measurement reliability.
• in PV system performance monitoring, in addition to instruments measuring in the
plane of array, horizontally placed instruments are used for the measurement of
global radiation. Global irradiance data enable the user to compare the local climate
and system efficiency between different sites. These data can also be compared to
measurements by local meteorological stations.

6.3 Speed of repair and maintenance

Dependability is not only a matter of reliability but also involves the reaction to
problems; if the processing time of service and repairs is short, this contributes to the
dependability.

Hukseflux pyranometers are designed to allow easy maintenance and repair. The main
maintenance actions are:

• replacement of desiccant
• replacement of cabling

For optimisation of dependability a user should:

• estimate the expected lifetime of the instrument

• design a schedule of regular maintenance
• design a schedule of repair or replacement in case of defects

When operating multiple instruments in a network Hukseflux recommends keeping

procedures simple and having a few spare instruments to act as replacements during
service, recalibrations and repair.

6.4 Uncertainty evaluation

The uncertainty of a measurement under outdoor or indoor conditions depends on many

factors, see paragraph 1 of this chapter. It is not possible to give one figure for
pyranometer measurement uncertainty. The work on uncertainty evaluation is “in
progress”. There are several groups around the world participating in standardisation of
the method of calculation. The effort aims to work according to the guidelines for
uncertainty evaluation (according to the “Guide to Expression of Uncertainty in
Measurement” or GUM).

SR20 manual v1814 24/43

6.4.1 Evaluation of measurement uncertainty under outdoor conditions

Hukseflux actively participates in the discussions about pyranometer measurement

uncertainty; we also provide spreadsheets, reflecting the latest state of the art, to assist
our users in making their own evaluation. The input to the assessment is summarised:

1) The formal evaluation of uncertainty should be performed in accordance with ISO 98-3
Guide to the Expression of Uncertainty in Measurement, GUM.
2) The specifications of the instrument according to the list of ISO 9060 classification of
pyranometers and pyrheliometers are entered as limiting values of possible errors, to be
analysed as type B evaluation of standard uncertainty per paragraph 4.3.7. of GUM. A
priori distributions are chosen as rectangular.
3) A separate estimate has to be entered to allow for estimated uncertainty due to the
instrument maintenance level.
4) The calibration uncertainty has to be entered. Please note that Hukseflux calibration
uncertainties are lower than those of alternative equipment. These uncertainties are
entered in measurement equation (equation is usually Formula 0.1: E = U/S), either as
an uncertainty in E (zero offsets, directional response) in U (voltage readout errors) or
in S (tilt error, temperature dependence, calibration uncertainty).
5) In uncertainty analysis for pyranometers, the location and date of interest is entered.
The course of the sun is then calculated, and the direct and diffuse components are
estimated, based on a model; the angle of incidence of direct radiation is a major factor
in the uncertainty.
6) In uncertainty analysis for modern pyrheliometers: tilt dependence often is so low that
one single typical observation may be sufficient.
7) In case of special measurement conditions, typical specification values are chosen.
These should for instance account for the measurement conditions (shaded / unshaded,
ventilated/ unventilated, horizontal / tilted) and environmental conditions (clear sky /
cloudy, working temperature range).
8) Among the various sources of uncertainty, some are “correlated”; i.e. present during
the entire measurement process, and not cancelling or converging to zero when
averaged over time; the off-diagonal elements of the covariance matrix are not zero.
Paragraph 5.2 of GUM.
9) Among the various sources of uncertainty, some are “uncorrelated”; cancelling or
converging to zero when averaged over time; the off-diagonal elements of the covariance
matrix are zero. Paragraph 5.1 of GUM.
10) Among the various sources of uncertainty, some are “not included in analysis”; this
applies for instance to non-linearity for pyranometers, because it is already included in
the directional error, and the spectral response for pyranometers and pyrheliometers
because it is already taken into account in the calibration process.

SR20 manual v1814 25/43

Table 6.4.1.1 Preliminary estimates of achievable uncertainties of measurements with
Hukseflux pyranometers. The estimates are based on typical pyranometer properties and
calibration uncertainty, for sunny, clear sky days and well maintained stations, without
uncertainty loss due to lack of maintenance and due to instrument fouling. The table
specifies expanded uncertainties with a coverage factor of 2 and confidence level of
95 %. Estimates are based on 1 s sampling. IMPORTANT NOTE: there is no international
consensus on uncertainty evaluation of pyranometer measurements, so this table should
not be used as a formal reference.

Pyranometer season latitude uncertainty uncertainty uncertainty

class minute totals hourly totals daily totals
(ISO 9060) at solar noon at solar noon

secondary summer mid-latitude 2.7 % 2.0 % 1.9 %

standard
(SR20) equator 2.6 % 1.9 % 1.7 %
pole 7.9 % 5.6 % 4.5 %
winter mid-latitude 3.4 % 2.5 % 2.7 %
first class summer mid-latitude 4.7 % 3.3 % 3.4 %
equator 4.4 % 3.1 % 2.9 %
pole 16.1% 11.4 % 9.2 %
winter mid-latitude 6.5 % 4.5 % 5.2 %
second class summer mid-latitude 8.4 % 5.9 % 6.2 %
equator 7.8 % 5.5 % 5.3 %
pole 29.5 % 21.6 % 18.0 %
winter mid-latitude 11.4 % 8.1 % 9.9 %

6.4.2 Calibration uncertainty

New calibration procedures were developed in close cooperation with PMOD World
Radiation Center in Davos, Switzerland. The latest calibration method results in an
uncertainty of the sensitivity of less than 1.2 %, compared to typical uncertainties of
higher than 1.7 % for this pyranometer class. See the appendix for detailed information
on calibration hierarchy.

SR20 manual v1814 26/43

7 Maintenance and trouble shooting
7.1 Recommended maintenance and quality assurance

SR20 can measure reliably at a low level of maintenance in most locations. Usually
unreliable measurements will be detected as unreasonably large or small measured
values. As a general rule this means that regular visual inspection combined with a
critical review of the measured data, preferably checking against other measurements, is
the preferred way to obtain a reliable measurement.

Table 7.1.1 Recommended maintenance of SR20. If possible the data analysis and
cleaning (1 and 2) should be done on a daily basis.

MINIMUM RECOMMENDED PYRANOMETER MAINTENANCE

INTERVAL SUBJECT ACTION
1 1 week data analysis compare measured data to maximum possible / maximum
expected irradiance and to other measurements nearby
(redundant instruments). Also historical seasonal records can
be used as a source for expected values. Analyse night time
signals. These signals may be negative (down to - 5 W/m2 on
clear windless nights), due to zero offset a. In case of use with
PV systems, compare daytime measurements to PV system
output. Look for any patterns and events that deviate from
what is normal or expected.
2 2 weeks cleaning use a soft cloth to clean the dome of the instrument,
persistent stains can be treated with soapy water or alcohol
3 6 months inspection inspect cable quality, inspect connectors, inspect mounting
position, inspect cable, clean instrument, clean cable, inspect
levelling, change instrument tilt in case this is out of
specification, inspect mounting connection, inspect interior of
dome for condensation
4 2 years desiccant desiccant replacement (if applicable). Change in case the blue
replacement colour of the 40 % humidity indicator turns pink (indicating
humidity), then replace desiccant. Coat the rubber of the
cartridge with silicone grease or vaseline. Desiccant
regeneration: heating in an oven at 70 °C for 1 to 2 hours.
Humidity indicator regeneration: heating until blue at 70 °C
5 recalibration recalibration by side-by-side comparison to a higher standard
instrument in the field according to ISO 9847
6 lifetime judge if the instrument should be reliable for another 2 years,
assessment or if it should be replaced
7 6 years parts if applicable / necessary replace the parts that are most
replacement exposed to weathering; cable, connector, desiccant holder,
sun screen. NOTE: use Hukseflux approved parts only.
8 internal if applicable: open instrument and inspect / replace O-rings;
inspection dry internal cavity around the circuit board
9 recalibration recalibration by side-by-side comparison to a higher standard
instrument indoors according to ISO 9847 or outdoors
according to ISO9846

SR20 manual v1814 27/43

7.2 Trouble shooting

Table 7.2.1 Trouble shooting for SR20

The sensor Check the electrical resistance of the sensor between the green
does not give (-) and white (+) wire. Use a multimeter at the 1000 Ω range. Measure the sensor
any signal resistance first with one polarity, than reverse the polarity. Take the average
value. The typical resistance of the wiring is 0.1 Ω/m. Typical resistance should be
the typical sensor resistance of 100 to 200 Ω plus 1.5 Ω for the total resistance of
two wires (back and forth) of each 5 m. Infinite resistance indicates a broken
circuit; zero or a low resistance indicates a short circuit.
Check if the sensor reacts to light: put the multimeter at its most sensitive range
of DC voltage measurement, typically the 100 x 10-3 VDC range or lower. Expose
the sensor to strong light source, for instance a 100 W light bulb at 1 x 10-1 m
distance. The signal should read > 2 x 10-3 V now. Darken the sensor either by
putting something over it or switching off the light. The instrument voltage output
should go down and within one minute approach 0 V. Check the data acquisition
by applying a 1 x 10-6 V source to it in the 1 x 10-6 V range. Check the condition of
the connectors (on chassis as well as the cable).

The sensor Note that night-time signals may be negative (down to -5 W/m2 on clear windless
signal is nights), due to zero offset a.
unrealistically Check if the pyranometer has clean domes.
high or low. Check the location of the pyranometer; are there any obstructions that could
explain the measurement result.
Check the orientation / levelling of the pyranometer.
Check if the right calibration factor is entered into the algorithm. Please note that
each sensor has its own individual calibration factor, as documented in its
calibration certificate.
Check if the voltage reading is divided by the calibration factor in review of the
algorithm. Check the condition of the wiring at the logger.
Check the cable condition looking for cable breaks. Check the condition of the
connectors (on chassis as well as the cable). Check the range of the data logger;
signal can be negative (this could be out of range) or the amplitude could be out
of range. Check the data acquisition by applying a 1 x 10-6 V source to it in the
1 x 10-6 V range. Look at the output. Check if the output is as expected.
Check the data acquisition by short circuiting the data acquisition input with a 100
Ω resistor. Look at the output. Check if the output is close to 0 W/m2.

The sensor Check the presence of strong sources of electromagnetic radiation (radar, radio)
signal shows Check the condition of the shielding.
unexpected Check the condition of the sensor cable.
variations Check if the cable is not moving during the measurement
Check the condition of the connectors (on chassis as well as the cable)

The outer In case there is a minor layer of moisture that is hardly visible: replace the
dome shows desiccant and wait a few days to see if the situation improves.
internal In case of condensation of droplets: disassemble the instrument and dry out the
condensation. parts.

The inner Arrange to send the sensor back to Hukseflux for diagnosis.
dome shows
internal
condensation

SR20 manual v1814 28/43

7.3 Calibration and checks in the field

Recalibration of field pyranometers is typically done by comparison in the field to a

reference pyranometer. The applicable standard is ISO 9847 “International Standard-
Solar Energy- calibration of field pyranometers by comparison to a reference
pyranometer”. At Hukseflux an indoor calibration according to the same standard is used.

Hukseflux recommendation for re-calibration: if possible, perform calibration indoor by

comparison to an identical reference instrument, under normal incidence conditions.

In case of field comparison; ISO recommends field calibration to a higher class

pyranometer. Hukseflux suggests also allowing use of sensors of the same model and
class, because intercomparisons of similar instruments have the advantage that they
suffer from the same offsets. It is therefore just as good to compare to pyranometers of
the same brand and type as to compare to an instrument of a higher class. ISO
recommends to perform field calibration during several days; 2 to 3 days under cloudless
conditions, 10 days under cloudy conditions. In general this is not achievable. In order to
shorten the calibration process Hukseflux suggests to allow calibration at normal
incidence, using hourly totals near solar noon.

Hukseflux main recommendations for field intercomparisons are:

1) to take normal incidence as a reference and not the entire day.

2) to take a reference of the same brand and type as the field pyranometer or a
pyranometer of a higher class, and
3) to connect both to the same electronics, so that electronics errors (also offsets) are
eliminated.
4) to mount all instruments on the same platform, so that they have the same body
temperature.
5) assuming that the electronics are independently calibrated, to analyse radiation values
at normal incidence radiation (possibly tilting the radiometers to approximately normal
incidence), if this is not possible to compare 1 hour totals around solar noon for
horizontally mounted instruments.
6) for second class radiometers, to correct deviations of more than ± 10 %. Lower
deviations should be interpreted as acceptable and should not lead to a revised
sensitivity.
7) for first class pyranometers, to correct deviations of more than ± 5 %. Lower
deviations should be interpreted as acceptable and should not lead to a revised
sensitivity.
8) for secondary standard instruments, to correct deviations of more than ± 3 %. Lower
deviations should be interpreted as acceptable and should not lead to a revised
sensitivity.

SR20 manual v1814 29/43

7.4 Data quality assurance

Quality assurance can be done by:

• analysing trends in solar irradiance signal

• plotting the measured irradiance against mathematically generated expected values
• comparing irradiance measurements between sites
• analysis of night time signals

The main idea is that one should look out for any unrealistic values. There are programs
on the market that can semi-automatically perform data screening. See for more
information on such a program http://www.dqms.com.

SR20 manual v1814 30/43

SR20 manual v1814 31/43
8 Appendices
8.1 Appendix on cable extension / replacement

The sensor cable of SR20 is equipped with a M16 straight connector. In case of cable
replacement, it is recommended to purchase a new cable with connector at Hukseflux.
An alternative is to choose for a Do-it-yourself (DIY) approach; please ask for the DIY
connector assembly guide. In case of cable extension, the user may choose purchasing a
new cable with connector at Hukseflux or extending the existing cable himself. Please
note that Hukseflux does not provide support for DIY connector- and cable assembly.
SR20 is equipped with one cable. Keep the distance between data logger or amplifier and
sensor as short as possible. Cables act as a source of distortion by picking up capacitive
noise. In an electrically “quiet” environment the SR20 cable can be extended without
problem to 100 metres. If done properly, the sensor signal, although small, will not
significantly degrade because the sensor resistance is very low (so good immunity to
external sources) and because there is no current flowing (so no resistive losses).
Connector, cable and cable connection specifications are summarised below.

Table 8.1.1 Preferred specifications for SR20 cable replacement and extension

General replacement please order a new cable with connector at Hukseflux or choose for a DIY
approach. In case of DIY replacement by the user see connector
specifications below and ask for the DIY connector assembly guide

General cable extension please order a new cable with connector at Hukseflux or solder the new
cable conductors and shield to the original sensor cable and make a
connection, using adhesive-lined heat shrink tubing, with specifications for
outdoor use. Always connect shield

Connectors used chassis: M16 panel connector, male thread, 10-pole, HUMMEL AG
7.840.200.000 panel connector, front mounting, short version.
cable: M16 straight connector, female thread, 10-pole. HUMMEL AG
7.810.300.00M straight connector, female thread, for cable 3 to 6 x 10-3
m, special version

Cable 8-wire, shielded, with copper conductors (at Hukseflux 8-wire shielded
cable is used, of which 2 wires are used for signal transmission, 2 for
heating and 2 to 4 for the temperature sensor)

Conductor resistance < 0.1 Ω/m

Length cables should be kept as short as possible, in any case the total cable
length should be less than 100 m

Outer sheath with specifications for outdoor use

(for good stability in outdoor applications)

SR20 manual v1814 32/43

8.2 Appendix on tools for SR20

Table 8.2.1 Specifications of tools for SR20

tooling required for sun screen fixation and removal by hand

tooling required for bottom plate fixation and removal hex key 2.5 mm

tooling required for desiccant holder fixation and spanner size 20 mm

removal

8.3 Appendix on spare parts for SR20

• Desiccant holder (with glass window and rubber ring)

• Desiccant (set of 5 bags in air tight bag)
• Humidity indicator
• Levelling feet (set of 2)
• Static foot
• Sun screen with metal ring and thumb screw
• SR20 cable with connector (specify length in multiples of 5 m)
• O-ring SR20

NOTE: Outer dome, level and sensor of SR20 cannot be supplied as spare parts. In
case of possible damage to the SR20, after repair the instrument must be tested to
verify performance within specification limits. This is required by ISO 9060. Testing
involves verification of the directional response after dome, thermal sensor and level
replacement and verification of the temperature response after thermal sensor
replacement.

SR20 manual v1814 33/43

8.4 Appendix on standards for classification and calibration

Both ISO and ASTM have standards on instrument classification and methods of
calibration. The World Meteorological Organisation (WMO) has largely adopted the ISO
classification system.

Table 8.4.1 Pyranometer standardisation in ISO and ASTM.

STANDARDS ON INSTRUMENT CLASSIFICATION AND CALIBRATION

ISO STANDARD EQUIVALENT ASTM STANDARD

ISO 9060:1990 Solar energy -- Specification not available

and classification of instruments for measuring Comment: work is in progress on a new ASTM
hemispherical solar and direct solar radiation equivalent standard

Comment: a standard “Solar energy --Methods not available

for testing pyranometer and pyrheliometer
characteristics” has been announced in ISO
9060 but is not yet implemented.

ISO 9846:1993 Solar energy -- Calibration of ASTM G167 - 05 Standard Test Method for
a pyranometer using a pyrheliometer Calibration of a Pyranometer Using a
Pyrheliometer

ISO 9847:1992 Solar energy -- Calibration of ASTM E 824 -10 Standard Test Method for
field pyranometers by comparison to a Transfer of Calibration from Reference to Field
reference pyranometer Radiometers

ASTM G207 - 11 Standard Test Method for

Indoor Transfer of Calibration from Reference to
Field Pyranometers

ISO 9059:1990 Solar energy -- Calibration of ASTM E 816 Standard Test Method for
field pyrheliometers by comparison to a Calibration of Pyrheliometers by Comparison to
reference pyrheliometer Reference Pyrheliometers

SR20 manual v1814 34/43

8.5 Appendix on calibration hierarchy

The World Radiometric Reference (WRR) is the measurement standard representing the
SI unit of irradiance. It was introduced in order to ensure world-wide homogeneity of
solar radiation measurements and is in use since 1980. The WRR was determined from
the weighted mean of the measurements of a group of 15 absolute cavity radiometers
which were fully characterised. It has an estimated accuracy of 0.3 %. The WMO
introduced its mandatory use in its status in 1979.
The world-wide homogeneity of the meteorological radiation measurements is
guaranteed by the World Radiation Center in Davos Switzerland, by maintaining the
World Standard Group (WSG) which materialises the World Radiometric Reference.

See http://www.pmodwrc.ch

The Hukseflux standard is traceable to an outdoor WRR calibration. Some small

corrections are made to transfer this calibration to the Hukseflux standard conditions:
sun at zenith and 1000 W/m2 irradiance level. During the outdoor calibration the sun is
typically at 20 to 40° zenith angle, and the total irradiance at a 700 W/m2 level.

Table 8.5.1 Calibration hierarchy for pyranometers

WORKING STANDARD CALIBRATION AT PMOD / WRC DAVOS

Calibration of working standard pyranometers:

Method: ISO 9846, type 1 outdoor. This working standard has an uncertainty “uncertainty of
standard”. The working standard has been calibrated under certain “test conditions of the
standard”. The working standard has traceability to WRR world radiometric reference.

CORRECTION OF (WORKING) STANDARD CALIBRATION TO STANDARDISED

REFERENCE CONDITIONS

Correction from “test conditions of the standard” to “reference conditions” i.e. to normal
incidence and 20 °C:
Using known (working) standard pyranometer properties: directional, non linearity, offsets,
temperature dependence). This correction has an uncertainty; “uncertainty of correction”.
At Hukseflux we also call the working standard pyranometer “standard”.

INDOOR PRODUCT CALIBRATION

Calibration of products, i.e. pyranometers:

Method: according to ISO 9847, Type IIc, which is an indoor calibration.
This calibration has an uncertainty associated with the method.
(In some cases like the BSRN network the product calibration is with a different method; for
example again type 1 outdoor)

CALIBRATION UNCERTAINTY CALCULATION

ISO 98-3 Guide to the Expression of Uncertainty in Measurement, GUM Determination of

combined expanded uncertainty of calibration of the product, including uncertainty of the
working standard, uncertainty of correction, uncertainty of the method (transfer error). The
coverage factor must be determined; at Hukseflux we work with a coverage factor k = 2.

SR20 manual v1814 35/43

8.6 Appendix on meteorological radiation quantities

A pyranometer measures irradiance. The time integrated total is called radiant exposure.
In solar energy radiant exposure is often given in W∙h/m 2.

Table 8.6.1 Meteorological radiation quantities as recommended by WMO (additional

symbols by Hukseflux Thermal Sensor). POA stands for Plane of Array irradiance. The
term originates from ASTM and IEC standards.

SYMBOL DESCRIPTION CALCULATION UNITS ALTERNATIVE

EXPRESSION

E↓ downward irradiance E↓ = Eg ↓ + El↓ W/m2

H↓ downward radiant exposure H↓ = Hg↓ + Hl ↓ J/m2

for a specified time interval
E↑ upward irradiance E↑ = Eg↑ + El ↑ W/m2
H↑ upward radiant exposure H↑ = Hg↑ + Hl ↑ J/m2 W∙h/m2 Change of
for a specified time interval units
E direct solar irradiance W/m2 DNI Direct
normal to the apparent Normal
solar zenith angle Irradiance
E0 solar constant W/m2
Eg ↓ h global irradiance; Eg↓ = E cos θh + Ed↓ W/m2 GHI Global
hemispherical irradiance on Horizontal
a specified, in this case Irradiance
horizontal surface.*
Eg ↓ t global irradiance; Eg ↓ = E∙cos θt + W/m2 POA Plane of
hemispherical irradiance on Ed ↓ t + Er↑ t *** Array
a specified, in this case
tilted surface.*
Ed ↓ downward diffuse solar W/m2 DHI Diffuse
radiation Horizontal
Irradiance
El ↑, El ↓ upward / downward long- W/m2
wave irradiance
Er↑ reflected solar irradiance W/m2
E* net irradiance E* = E↓ – E↑ W/m2

T↓ apparent surface ºC or K
temperature**
T↑ apparent sky ºC or K
temperature**
SD sunshine duration h

θ is the apparent solar zenith angle θh relative to horizontal, θt relative to a tilted surface
g = global, l = long wave, t = tilted *, h = horizontal*
* distinction horizontal and tilted from Hukseflux,
** T symbols introduced by Hukseflux,
*** contributions of Ed ↓ t and Er↑ t are Ed ↓ and Er↑ both corrected for the tilt angle of the
surface

SR20 manual v1814 36/43

8.7 Appendix on ISO and WMO classification tables

Table 8.7.1 Classification table for pyranometers per ISO 9060 and WMO.
NOTE: WMO specification of spectral selectivity is different from that of ISO. Hukseflux
conforms to the ISO limits. WMO also specifies expected accuracies. ISO finds this not to
be a part of the classification system because it also involves calibration. Please note that
WMO achievable accuracies are for clear days at mid latitudes and that the uncertainty
estimate does not include uncertainty due to calibration*.

ISO CLASSIFICATION** TABLE

ISO CLASS SECONDARY FIRST CLASS SECOND

STANDARD CLASS
Specification limit
Response time (95 %) 15 s 30 s 60 s
Zero offset a (response to 200 W/m2 net + 7 W/m2 + 15 W/m2 + 30 W/m2
thermal radiation)
Zero offset b (response to 5 K/h in ambient ± 2 W/m2 ± 4 W/m2 ± 8 W/m2
temperature)
Non-stability (change per year) ± 0.8 % ± 1.5 % ±3%
Non-linearity (100 to 1000 W/m2) ± 0.5 % ±1% ±3%
Directional response ± 10 W/m2 ± 20 W/m2 ± 30 W/m2
Spectral selectivity (350 to 1500 x 10-9 m) ±3% ±5% ± 10 %
Temperature response (interval of 50 K)* 2% 4% 8%
Tilt response ± 0.5 % ±2% ±5%
(0 to 90 ° at 1000 W/m2)
ADDITIONAL WMO SPECIFICATIONS

WMO CLASS HIGH QUALITY GOOD QUALITY MODERATE

QUALITY
WMO: achievable accuracy for daily sums* 2% 5% 10 %
WMO: achievable accuracy for hourly sums* 3% 8% 20 %
WMO: achievable accuracy for minute sums* not specified not specified not specified
WMO: resolution 1 W/m2 5 W/m2 10 W/m2
(smallest detectable change)
WMO: spectral selectivity ±2% ±5% ± 10 %
(300 to 3000 x 10-9 m)
CONFORMITY TESTING***

ISO 9060 individual group group

instrument only: compliance compliance
all specs must
comply

* WMO 7.2.1: The estimated uncertainties are based on the following assumptions: (a)
instruments are well-maintained, correctly aligned and clean; (b) 1 min and 1 h figures
are for clear-sky irradiances at solar noon; (c) daily exposure values are for clear days at
mid-latitudes. WMO 7.3.2.5: Table 7.5 lists the expected maximum deviation from the
true value, excluding calibration errors.
** At Hukseflux the expression ± 1 % is used instead of a range of 2 %.
*** an instrument is subject to conformity testing of its specifications. Depending on the
classification, conformity compliance can be proven either by group- or individual
compliance. A specification is fulfilled if the mean value of the respective test result does
not exceed the corresponding limiting value of the specification for the specific category
of instrument.

SR20 manual v1814 37/43

8.8 Appendix on definition of pyranometer specifications

Table 8.8.1 Definition of pyranometer specifications

SPECIFICATION DEFINITION SOURCE

Response time time for 95 % response. The time interval between the instant ISO
(95 %) when a stimulus is subjected to a specified abrupt change and the 9060-
instant when the response reaches and remains within specified 1990
limits around its final steady value.The response time is a measure WMO
of the thermal inertia inherent in the stabilization period for a final 1.6.3
reading.
Zero offset a: response to 200 W/m2 net thermal radiation (ventilated). ISO
(200 W/m2 net Hukseflux assumes that unventilated instruments have to specify 9060-
thermal the zero-offset in unventilated – worst case – conditions. 1990
radiation ) Zero offsets are a measure of the stability of the zero-point.
Zero offset a is visible at night as a negative offset, the instrument
dome irradiates in the far infra red to the relatively cold sky. This
causes the dome to cool down. The pyranometer sensor irradiates
to the relatively cool dome, causing a negative offset. Zero offset
a is also assumed to be present during daytime.
Zero offset b: response to 5 K/h change in ambient temperature. ISO
(5 K/h in ambient Zero offsets are a measure of the stability of the zero-point. 9060-
temperature) 1990
Non-stability percentage change in sensitivity per year. The dependence of ISO
(change per sensitivity resulting from ageing effects which is a measure of the 9060-
year) long-term stability. 1990
Non-linearity percentage deviation from the sensitivity at 500 W/m2 due to the ISO
(100 to 1000 change in irradiance within the range of 100 W/m2 to 1000 W/m2. 9060-
W/m2) Non-linearity has an overlap with directional response, and 1990
therefore should be handled with care in uncertainty evaluation.
Directional the range of errors caused by assuming that the normal incidence ISO
response sensitivity is valid for all directions when measuring from any 9060-
direction a beam radiation whose normal incidence irradiance is 1990
1000 W/m2 . Directional response is a measure of the deviations
from the ideal “cosine behaviour” and its azimuthal variation.
Spectral percentage deviation of the product of spectral absorptance and ISO
selectivity (350 spectral transmittance from the corresponding mean within 350 x 9060-
to 1500 x 10-9 m) 10-9 m to 1500 x 10-9 m. Spectral selectivity is a measure of the 1990
(WMO 300 to spectral selectivity of the sensitivity.
3000 x 10-9 m)
Temperature percentage deviation of the sensitivity due to change in ambient ISO
response temperature within an interval of 50 K the temperature of the 9060-
(interval of 50 K) pyranometer body. 1990
Tilt response percentage deviation from the sensitivity at 0° tilt (horizontal) due ISO
(0° to 90° at to change in tilt from 0° to 90° at 1000 W/m2 irradiance. Tilt 9060-
1000 W/m2) response describes changes of the sensitivity due to changes of 1990
the tilt angle of the receiving surface.
Sensitivity the change in the response of a measuring instrument divided by WMO
the corresponding change in the stimulus. 1.6.3
Spectral range the spectral range of radiation to which the instrument is Hukseflux
sensitive. For a normal pyranometer this should be in the 0.3 to 3
x 10-6 m range. Some pyranometers with coloured glass domes
have a limited spectral range.

SR20 manual v1814 38/43

8.9 Appendix on terminology / glossary

Table 8.9.1 Definitions and references of used terms

TERM DEFINITION (REFERENCE)

Solar energy solar energy is the electromagnetic energy emitted by the sun. Solar energy is
or solar also called solar radiation and shortwave radiation. The solar radiation incident
radiation on the top of the terrestrial atmosphere is called extra-terrestrial solar radiation;
97 % of which is confined to the spectral range of 290 to 3 000 x 10-9 m. Part of
the extra-terrestrial solar radiation penetrates the atmosphere and directly
reaches the earth’s surface, while part of it is scattered and / or absorbed by the
gas molecules, aerosol particles, cloud droplets and cloud crystals in the
atmosphere. The former is the direct component, the latter is the diffuse
component of the solar radiation. (ref: WMO, Hukseflux)
Hemispherical solar radiation received by a plane surface from a 180° field of view angle (solid
solar radiation angle of 2 π sr).(ref: ISO 9060)
Global solar the solar radiation received from a 180° field of view angle on a horizontal
radiation surface is referred to as global radiation. Also called GHI. This includes radiation
received directly from the solid angle of the sun’s disc, as well as diffuse sky
radiation that has been scattered in traversing the atmosphere. (ref: WMO)
Hemispherical solar radiation received by a horizontal plane surface.
(ref: ISO 9060)
Plane-of-array also POA: hemispherical solar irradiance in the plane of a PV array.
irradiance (ref: ASTM E2848-11 / IEC 61724)

Direct solar radiation received from a small solid angle centred on the sun’s disc, on a given
radiation plane. (ref: ISO 9060)
Terrestrial or radiation not of solar origin but of terrestrial and atmospheric origin and having
Longwave longer wavelengths (3 000 to 100 000 x 10-9 m). In case of downwelling El ↓ also
radiation the background radiation from the universe is involved, passing through the
”atmospheric window”. In case of upwelling El ↑, composed of long-wave
electromagnetic energy emitted by the earth’s surface and by the gases, aerosols
and clouds of the atmosphere; it is also partly absorbed within the atmosphere.
For a temperature of 300 K, 99.99 % of the power of the terrestrial radiation has
a wavelength longer than 3 000 x 10-9 m and about 99 per cent longer than
5 000 x 10-9 m. For lower temperatures, the spectrum shifts to longer
wavelengths. (ref: WMO)
World measurement standard representing the Sl unit of irradiance with an uncertainty
Radiometric of less than ± 0.3 % (see the WMO Guide to Meteorological Instruments and
Reference Methods of Observation, 1983, subclause 9.1.3). The reference was adopted by
(WRR) the World Meteorological Organization (WMO) and has been in effect since 1 July
1980. (ref: ISO 9060)
Albedo ratio of reflected and incoming solar radiation. Dimensionless number that varies
between 0 and 1. Typical albedo values are: < 0.1 for water, from 0.1 for wet
soils to 0.5 for dry sand, from 0.1 to 0.4 for vegetation, up to 0.9 for fresh snow.
Angle of angle of radiation relative to the sensor measured from normal incidence (varies
incidence from 0° to 90°).
Zenith angle angle of incidence of radiation, relative to zenith. Equals angle of incidence for
horizontally mounted instruments
Azimuth angle angle of incidence of radiation, projected in the plane of the sensor surface.
Varies from 0° to 360°. 0 is by definition the cable exit direction, also called
north, east is + 90°. (ASTM G113-09)
Sunshine sunshine duration during a given period is defined as the sum of that sub-period
duration for which the direct solar irradiance exceeds 120 W/m2. (ref: WMO)

SR20 manual v1814 39/43

8.10 Appendix on converting resistance to temperature

SR20 is equipped with an internal temperature sensor. This can be either a Pt100 (SR20-
T1 version) or a 10 kΩ thermistor (SR20-T2 version), as ordered.

Both versions require the user to measure the resistance of the temperature sensor and
convert this value to temperature. Many dataloggers have built-in functions to perform
such a conversion. In case the user wishes to calculate temperature (in degrees Celsius)
from resistance (in Ohms) himself, there are two distinct procedures:

SR20-T1

T1 versions are equipped with a Pt100 platinum resistance thermometer. It is classified

as class A according to DIN EN 60751. It has a resistance of 100 Ω at a temperature of 0
°C.

To convert resistance in Ω to temperature in °C, one can use the following equation:

R Pt100
−𝐴 + �𝐴2 − 4𝐵 �1 − � (Formula 8.10.1)
100
𝑇=
2𝐵

with RPt100 the resistance in Ω, T the temperature in °C, A and B the Pt100 coefficients

A = 3.908 x 10-3
B = -5.775 x 10-7

SR20-T2

T2 versions are equipped with a 10 kΩ thermistor of type 44031RC. It has a resistance of

10000 Ω at a temperature of 25 °C.

To convert resistance in Ω to temperature in °C, one can use the Steinhart-Hart

equation. Measure the resistance of the thermistor and then calculate the temperature
from the resistance.

1
𝑇= − 273.15 (Formula 8.10.2)
𝛼 + 𝛽 ln(R thermistor ) + 𝛾 ln(R thermistor )3

with Rthermistor the thermistor resistance in Ω, T the temperature in °C, α, β and γ the
Steinhart-Hart coefficients

α= 1.0295 x 10-3
β= 2.391 x 10-4
γ= 1.568 x 10-7

SR20 manual v1814 40/43

8.11 EU declaration of conformity

We, Hukseflux Thermal Sensors B.V.

Delftechpark 31
2628 XJ Delft
The Netherlands

in accordance with the requirements of the following directives:

2011/65/EU The Restriction of Hazardous Substances Directive

2014/30/EU The Electromagnetic Compatibility Directive

hereby declare under our sole responsibility that:

Product model: SR20

Product type: Pyranometer

has been designed to comply and is in conformity with the relevant sections and
applicable requirements of the following standards:

Emission: IEC/EN 61000-6-1, Class B, RF emission requirements, IEC CISPR11

and EN 55011 Class B requirements
Immunity: IEC/EN 61000-6-2 and IEC 61326 requirements
Report: “EMC test 08C01340RPT01 LP02 v06012009.pdf”, 09 January, 2009

Eric HOEKSEMA
Director
Delft
20 April, 2016

SR20 manual v1814 41/43

 © 2018, Hukseflux Thermal Sensors B.V.
www.hukseflux.com

Hukseflux Thermal Sensors B.V. reserves the right to change specifications without notice.