Seisdescri

CALTRANS
SEISMIC DESIGN
CRITERIA
VERSION 2.0
State of California
Department of Transportation
APRIL 2019
TABLE OF REVISIONS i
TABLE OF REVISIONS FROM SDC 1.7 TO SDC 2.0

SDC 1.7 SDC 2.0 Revision
Section Section
All All Rearranged design provisions in a “Code and Commentary”

Sections Sections format
Included new commentaries and references
Added Units to all empirical equations
Deleted Equations in Metric units
1. 1.1 Changed scope of the SDC from “Ordinary Standard bridges” to

“Ordinary Standard” and “Recovery Standard” bridges
Made major editorial revisions
1.1 1.2.1, Modified definition of an Ordinary Standard bridge, including
1.2.2 classification of Pier walls and “Foundations in modified soil” as
Nonstandard features
1.2 Deleted “Types of Components addressed in the SDC”
1.2 Added “Bridge Categories”
1.2.2 Added “Nonstandard Bridge Features”
1.2.4 Added “Recovery Bridge”
1.2.5 Added “Important Bridge”
1.3 Deleted “Bridge Systems”
1.3 Added “Seismic Performance Criteria”
1.4 Added “Design Philosophy”
Added “Seismic Design Procedure Flowchart” (new Appendix A)
1.5 Added “Procedure for Modifying the SDC”
2.1 Added “Definitions”

Appendix 2.2 and Separated the listing of Notations and Acronyms/Initialisms
A 2.3 Added more “Notations” and “Acronyms/Initialisms”
Clarified existing Notations
3.1 Added “Earthquake Resisting Elements”
©2019 California Department of Transportation

ALL RIGHTS reserved.
ii SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019

Section Section
3.2.1.1 Added “Safety Evaluation Earthquake” to the definition of Design
Spectrum
Deleted “deterministic criterion” from the definition of Design
Spectrum for Safety Evaluation Earthquake
Updated the online design tools for specification of Design
Spectrum
3.2.1.2 Added definition of Design Spectrum for Functional Evaluation
Earthquake
2.1.5 3.2.1.5 Modified the use of Damping Ratios (ratios other than 5% to
require a PSDC)
6.1.2 3.2.2 Clarified Liquefaction hazard
6.1.4 3.2.4 Modified provisions for “Additional Seismic Hazards”
3.2.3 3.3.3 Added provisions for Grade 80 Steel (Properties and usage
limitations)
3.2.7 Deleted “Other Material Properties”
5.6.1.1 3.4.2 Deleted Figure for “Effective Stiffness of Cracked Reinforced
Sections” and replaced it with equations for the relevant range of
axial load ratios
5.6.1.2 3.4.3 Changed “Effective Moment of Inertia for Box Girder
Superstructures” to “Effective Moment of Inertia for
Superstructures and Cap Beams”
Added provision for “effective moment of inertia for prestressed
sections”
5.6.2 3.4.4 Clarified provision for “Torsional Moment of Inertia for
Superstructures”
4.1.1 3.5.1 Added “Global Displacement Criteria” for Recovery bridges
and Clarified definitions of “frame/bent displacement capacity” and
“frame/bent displacement demand,” and extended the definitions
3.5.2
to cover abutments and in-span hinges
Defined “Local Principal/Critical Axes”
Made minor modification to Figure on “Global Force Deflection
Relationship”
3.2.1 3.6 Added “Load Factor”
Changed Resistance factor for shear from 0.9 to 1.0

TABLE OF REVISIONS iii

Section Section
4.5 4.2 Added “Nonlinear Time History Analysis” as a standard analysis
method
Added “Equal Displacement Approximation” language for ESA
and EDA
Added table: “Applicability of Methods for Displacement Demand
Analysis”
4.5.1 4.2.1 Provided equation for displacement demand using ESA
Added provision for determining the displacement demand of
single span bridges
2.1.2.1 4.2.2 Changed “Tension” and “Compression” models to “Individual
frame” and “Continuous global models”
and
Deleted Figure on “Global Axis Definition”
5.2.2
Deleted Method I (100/30 % rule) for application and
combination of horizontal ground motion
Made major editorial revisions
4.2.3 Added provisions for “Nonlinear Time History Analysis”
4.3.1 Added new provisions on abutment stiffness for Global models
5.5 Deleted “Simplified Analysis”
5.4 4.3.2 Clarified “Stand-Alone Models”
5.4.1 4.3.2.1 Modified Figures: Transverse and Longitudinal Stand-Alone
Models
and and
Changed “abutment stiffness” provision for Stand-Alone
5.4.2 4.3.2.2
longitudinal model
2.2.3 and 4.4.1 Clarified terms used in definition of displacement ductility
2.2.4 demand
Added limiting values for displacement ductility demand for
SCMs other than columns
Deleted displacement ductility demand values for pier walls
4.4.3.1 Added equations for Superstructure/Bent cap “Seismic Moment
and and Shear Demands”
4.4.3.2
4.2 4.4.4 Changed the factor for P-Delta equation from 0.20 to 0.25

iv SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019

Section Section
5.2.3 5.2.2 Clarified definition and application of Inelastic Static Analysis
Added provision for determining the displacement capacity of
single span bridges
Modified the applicability of equations for Local Displacement
Capacity
Editorial correction to Figure titled “Local Ductility Assessment”
3.1.1 5.3.1 Streamlined definition of seismic critical members (SCMs)
Removed “Pier walls” and “Type II shafts in soft/liquefiable soil”
as SCMs
5.3.3 Added provision for “Axial Load Limits”
5.3.5 Added “Confined Core”
3.5 5.3.6.1 Changed title from “Minimum Lateral Strength” to “Minimum
Flexural Capacity”
Clarified provision for “Minimum Flexural Capacity”
3.3.1 5.3.6.2 Added provision for Moment Curvature analysis of multi-column
bents in transverse direction to include overturning effects
3.6.3 5.3.7.3 Deleted equation for “Nominal Shear Reinforcement Capacity” of
Pier walls
3.8.2 5.3.8 Section title changed from “Lateral Reinforcement…” to
“Transverse Reinforcement…”
5.3.8.1 Added design provisions for transverse reinforcement
5.3.8.2 Added new provision for “Minimum volume of transverse
reinforcement” to replace the requirement for “Minimum local
displacement ductility capacity”
3.7.2 5.3.9.2 Deleted equation for “Minimum Longitudinal Reinforcement” of
Pier walls
3.6.5.3 5.3.9.3 Changed “maximum spacing of longitudinal bars in interlocking
portion of SCMs” from 8 to 12 inches
Corrected dimension for Figure titled “Vertical Reinforcement
within Interlocking Hoops”
3.4 5.4.1 Updated the list of Capacity Protected members (CPMs)
4.3.2 5.4.4 Added equations for Superstructure/Bent cap Seismic Capacity

Deleted moment equilibrium equations for Superstructure and
Bent Cap Seismic Capacity
TABLE OF REVISIONS v

Section Section
3.8.6 5.4.5 Modified the provision for transverse reinforcement for Type II
shafts
6.2.2 6.1.1 Adopted a new “Soil Classification”

“Competent” soil now classified as “Class S1” soil
All non-Competent soils (Marginal, Poor, Soft, potentially
liquefiable, and soil susceptible to lateral spreading) now
classified as “Class S2”
6.2.2.1 6.1.2 Modified the characteristics of Class S1 (previously
“Competent”) soil
6.2.2.3 Deleted “Marginal Soil”
6.2.1 Deleted “Foundation Performance”
6.2.3 Deleted “Foundation Design Criteria”
6.2.2.1 Added provisions for flexure and shear design of footings
7.7.1.6 Deleted “Effect of Large Capacity Piles on Footing Design”
7.7.1.7 6.2.2.5 Streamlined provisions for “Footing Stirrups”
Modified annotations and added a Note to the Figure captioned:
Footing Reinforcement – Fixed Column
6.2.2.6 Added provisions for “Spread Footings”
7.7.1.1 6.2.3.1 Modified the assumptions for design of pile foundations in class
S1 soils
6.2.3.2 Added provision for shear resistance of piles in class S1 soil
6.2.4.1 Added provision for design of pile foundations in class S2 soil
7.7.1.2A Deleted the provision allowing the simplified model for
Competent soil to be used for design of pile foundation in non-
soft/liquefiable marginal soil
6.2.4.2 Added “Comprehensive Foundation Design” for foundations in
class S2 soils (All foundations in class S2 soil to require a
comprehensive design)
7.7.1.2B Deleted “Lateral Capacity of Fixed Head Piles”
7.7.1.2C Deleted “Passive Earth Resistance for Pile Caps in Marginal
Soil”
2.2.5 6.2.4.3 Modified the provisions for “Scour and Liquefaction
Considerations”

vi SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019

Section Section
2.2.4 6.2.5.1 Major editorial revision to Types I and II shafts, including addition
of new provisions
Modified figure on “Shaft Definitions” and changed title to “Shaft
Types”
6.2.6 Added “Lateral Stability of Piles and Shafts”
7.7.3.3 Deleted “Shaft Diameter”
7.7.3.4 Deleted “Minimum Shaft Length”
7.7.3.1 6.2.5.2 Modified provisions for design of Type I shafts
7.7.3.2 6.2.5.3 Modified provisions for design of Type II shafts
7.8.1 6.3.1.2 Made a major revision to “Bilinear Model” for abutment
longitudinal stiffness, including incorporation of a skew reduction
factor
7.8.1 6.3.1.3 Added an equation for “effective abutment longitudinal stiffness
adjusted for a displacement coefficient between 2 and 4”
7.8.3 6.3.3 Modified the Equation and Figure for abutment support length
Changed terminology: “Abutment Seat Width” to “Abutment
Support Length”
7.8.4 6.3.4 Modified Equations for abutment shear key force demand
7.8.4.1 6.3.5 Added a new provision for minimum development length of
Headed bars used for shear key reinforcement
6.3.5.1 Added a new provision for Isolated Shear Key confinement
reinforcement
7.1.1 7.1.2 Deleted “Balanced Stiffness” equations for Constant Width

frames
Modified definition of terms used for “Balanced Stiffness”
Rearranged “Balanced Stiffness” equations
7.1.2 7.1.3 Rearranged “Balanced Frame Geometry” equation
Modified definition of terms used for “Balanced Frame
Geometry”
7.1.4 Deleted “End Span Consideration”
7.2.1.1 7.2.1.1 Modified “Effective Superstructure Width” Figures A and B
7.2.3 7.2.1.2 Clarified and added new provisions for “Precast Girders”
7.2.2 7.2.2 Clarified and revised provisions for “Vertical Acceleration”

TABLE OF REVISIONS vii

Section Section
7.2.5.4 7.2.3.1 Modified the Equation and Figure for In-span hinge support
length
and
Changed terminology from “Seat Width” to “Support Length”
7.2.3.2
Added new design provisions and made editorial clarifications
7.2.5.3 7.2.3.3 Clarified and modified provisions for “Shear Key Requirements
in the Transverse Direction”
7.2.7 7.2.3.5 Modified provisions for “Pipe Seat Extenders”
7.2.4 Added “Superstructure Depth”
7.2.8 Deleted “Equalizing Bolts”
7.3.1 7.3.1 Modified “Effective Width of Integral Bent Caps”
7.4.1 7.4.1 Clarified provision for “Joint Performance”
7.4.5.1 7.4.5.2 Clarified provisions for “T” and Knee Joint reinforcement
and and Modified figures for “Knee Joint Shear Reinforcement”
7.4.5.1 7.4.5.3
7.5 7.5.1 Added provision requiring PTFE spherical bearings to be used at
all in-span hinges
7.5.2 Added provisions for “Seismic Expansion Joints”
7.6.1 Added new provisions for Columns (core geometry, framing,
etc.)
7.6.2 Added provision for Column Dimensions for superstructures with
drop cap
7.6.5 7.6.3 Clarified provisions for Column Flares, including addition of
Figures for Horizontal and Vertical Flare Isolation
7.6.6 Deleted provisions for “Pier Wall”
7.6.7 7.6.4 Clarified equations for “Column Key Design”
Added provision and commentary to account for moment
generated by shear key steel
8.2.1 Added provisions on types and uses of “Reinforcing Bar Splices”

8.1.1 8.2.2.1 Clarified provisions for “No-Splice Zones” in SCMs

viii SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019

Section Section
8.1.4 8.2.2.3 Changed caption to “Hoop Splices and Spiral Terminations”
Clarified provisions for “Hoop and Spiral Reinforcement” in
SCMs
Added provisions for spiral reinforcement terminations
8.2.3.2 Added provisions for transverse reinforcement in Capacity
Protected Members
8.2.1 8.3.1.1 Modified the provision for “Minimum Development Length of
Longitudinal Reinforcement”
8.2.1 8.3.1.2 Clarified provision for development length of “Epoxy-coated
Longitudinal Bars” in SCMs
8.2.2 8.3.1.3 Clarified provision for development length of “Bundled Bars” in
SCMs
8.2.3.1 Deleted “Maximum Bar Diameter”
8.2.4 8.3.2 Modified the caption and provisions for “Embedment Length for
Column Reinforcement Extended into Type II Shafts”
8.3.3 Added “Reinforcing Bar Hooks”
8.2.5 8.4.1.1 Modified the provision for maximum spacing of transverse
reinforcement inside the plastic hinge region
8.4.1.2 Added provisions for maximum spacing of transverse
reinforcement “Outside the Plastic Hinge Region”
8.4.2 Added provisions for “Maximum and Minimum Lateral Spacing of
Longitudinal Reinforcement”
7.2.4 9 (9.1 Added a new Section dealing with specific design provisions for
through “Slab Bridges”
9.8)
Appendix Added a new appendix: “Seismic Design Procedure Flowchart”

A
Appendix Appendix Updated the web links and References for “Design Spectrum
B B Development”
Deleted information on “Deterministic criteria”
Deleted graphs for preliminary Design Spectrum for Soil Profile
Types B, C, D
Index Added an Index

CHANGES IN SECTION NUMBERING FROM SDC 1.7 TO SDC 2.0 ix
CHANGES IN SECTION NUMBERING FROM SDC 1.7 TO SDC 2.0
Version 1.7 Version 2.0 Version 1.7 Version 2.0

1. 1.1 3.6.5.2 5.3.7.5
1.1 1.2.1 3.6.5.3 5.3.9.3
1.2 Deleted 3.6.6.1 Deleted
1.3 Deleted 3.6.6.2 Deleted
1.4 2.1, 3.5.1, 4.3.1, 3.6.7 5.4.2, 5.4.3
C5.2.2 3.7.1 5.3.9.1
2.1 3.2.1.1 3.7.2 5.3.9.2
2.1.1 C3.2.1.1 3.7.3 Deleted
2.1.2 3.2.1.3 3.8.1 5.3.8.2
2.1.2.1 4.2.2 3.8.2 5.3.8.1
2.1.2.2 4.2.1 3.8.3 5.3.8.3
2.1.3 3.2.1.4 3.8.4 Deleted
2.1.4 Deleted 3.8.5 5.3.8.4
2.1.5 3.2.1.5 3.8.6 5.3.8.5, 5.4.5
2.2.1 4.2 4.1.1 3.5.1
2.2.2 4.3.1, 3.5, C5.2.2 4.1.2 4.4.1
2.2.3 4.4.1 4.1.3 Deleted
2.2.4 4.4.1, 6.2.5.1 4.2 4.4.4
2.2.5 6.2.4.3 4.3.1 4.4.2.1
2.3 2.1, C1.3.1 4.3.2 4.4.3.1, 4.4.3.2,
2.3.1 4.4.2.1 5.4.4
2.3.2.1 4.4.2.2 4.3.2.1 Deleted
2.3.2.2 Deleted 4.3.2.2 5.4.4
2.3.3 4.4.3.2 4.3.3 Deleted
3.1.1 5.3.1, C5.3.1, 8.2 5.1.1 4.2
3.1.2 2.1, 3.5.1, C5.2.2 5.2.1 4.2.1
3.1.3 C5.2.2 5.2.2 4.2.2
3.1.4 C5.2.2 5.2.3 5.2.2
3.1.4.1 C5.3.8.2 5.3 4.2.2, 4.3.1
3.2.1 3.3.1, 3.6 5.4 4.3.2
3.2.2 3.3.2 5.4.1 4.3.2.1
3.2.3 3.3.3 5.4.2 4.3.2.2
3.2.4 3.3.4 5.5 Deleted
3.2.5 3.3.5 5.6.1 3.4.1
3.2.6 3.3.6 5.6.1.1 3.4.2
3.2.7 Deleted 5.6.1.2 3.4.3
3.3.1 5.3.6.2 5.6.1.3 3.4.3
3.4 5.4.1 5.6.2 3.4.4
3.5 5.3.6.1 5.7 Deleted
3.6.1 5.3.7.1 6.1 3.2
3.6.2 5.3.7.2 6.1.1 3.2.1
3.6.3 5.3.7.3 6.1.2 3.2.2
3.6.5.1 5.3.7.4 6.1.3 3.2.3
x SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019
Version 1.7 Version 2.0 Version 1.7 Version 2.0

6.1.4 3.2.4 7.6.3 5.3.2
6.2.1 Deleted 7.6.4 5.3.6.2
6.2.2 6.1.1, C6.1.1 7.6.5.1 7.6.3.1, 7.6.3.2
6.2.2.1 6.1.2 7.6.5.2 7.6.3.3
6.2.2.2 Deleted 7.6.5.3 7.6.3.4
6.2.2.3 Deleted 7.6.6 Deleted
6.2.3.1 6.2.1 7.6.7 7.6.4
6.2.3.2 C6.1.3 7.7.1 Deleted
7.1 7.1.1 7.7.1.1 6.2.3.2
7.1.1 7.1.2 7.7.1.2 6.2.4.1
7.1.2 7.1.3 7.7.1.2A C6.2.4.1, C6.2.4.2
7.1.3 C7.1.2 7.7.1.2B Deleted
7.1.4 Deleted 7.7.1.2C Deleted
7.2.1.1 7.2.1.1 7.7.1.3 6.2.2.4
7.2.2 7.2.2 7.7.1.4 6.2.2.2
7.2.3 7.2.1.2 7.7.1.5 6.2.2.3
7.2.4 9 7.7.1.6 Deleted
7.2.5 7.2.3 7.7.1.7 6.2.2.5
7.2.5.1 C7.2.3.1, 7.2.3.2 7.7.2.1 Deleted
7.2.5.2 7.2.3.3 7.7.2.2 Deleted
7.2.5.3 7.2.3.3, C7.2.3.3 7.7.3.1 6.2.5.2
7.2.5.4 7.2.3.2 7.7.3.2 6.2.5.3
7.2.5.5 C7.2.3.2 7.7.3.3 Deleted
7.2.6 7.2.3.4 7.7.3.4 Deleted
7.2.7 7.2.3.5 7.7.3.5 C6.2.5.1
7.2.8 Deleted 7.7.4 6.2.5.4
7.3.1 C7.3.1 7.8.1 6.3.1.2, C6.3.1.1,
7.3.1.1 7.3.1 C6.3.1.2
7.3.2 7.3.2.1 7.8.2 6.3.2
7.3.2.1 7.3.2.2 7.8.3 6.3.3
7.3.4 7.3.3 7.8.4 6.3.4
7.4.1 7.4.1 7.8.4.1 6.3.5
7.4.2 7.4.2 7.8.4.1A 6.3.5.1
7.4.2.1 7.4.3 7.8.4.1B 6.3.5.1
7.4.3 7.4.4 8.1.1 8.2.2.1
7.4.4.1 7.4.2 8.1.2 8.2.2.2
7.4.4.2 7.4.5.1 8.1.3 8.2.3
7.4.4.3 7.4.5.2 8.1.4 8.2.2.3
7.4.5 C7.4.4.2 8.2.1 8.3.1
7.4.5.1 7.4.5.3 8.2.2 8.3.1.3
7.5.1 7.5.1, C7.5.1 8.2.3.1 Deleted
7.5.1 C7.5.1 8.2.4 8.3.2
7.5.2 C7.5.1 8.2.5 8.4.1
7.6.1 7.6.2
7.6.2 5.3.4
7.6.2.1 5.3.4
7.6.2.2 5.3.4
7.6.2.3 5.3.4
TABLE OF CONTENTS xi
TABLE OF CONTENTS
1. INTRODUCTION ....................................................................................................... 1-1
1.1 SCOPE .................................................................................................................... 1-1

1.2 BRIDGE CATEGORIES ........................................................................................... 1-2
1.2.1 Standard Bridge Features................................................................................ 1-2
1.2.2 Nonstandard Bridge Features ......................................................................... 1-3
1.2.3 Important Bridges ........................................................................................... 1-4
1.2.4 Recovery Bridges ........................................................................................... 1-5
1.2.5 Ordinary Bridges ............................................................................................. 1-5
1.3 SEISMIC PERFORMANCE CRITERIA ................................................................... 1-5
1.4 DESIGN PHILOSOPHY .......................................................................................... 1-8
1.5 PROCEDURE FOR MODIFYING THE SDC ......................................................... 1-10
2. DEFINITIONS, NOTATIONS AND ACRONYMS/INITIALISMS ................................. 2-1
2.1 DEFINITIONS ......................................................................................................... 2-1

2.2 NOTATIONS ............................................................................................................ 2-6
2.3 ACRONYMS AND INITIALISMS ............................................................................ 2-18
3. GENERAL REQUIREMENTS .................................................................................... 3-1
3.1 EARTHQUAKE RESISTING ELEMENTS ................................................................ 3-1

3.2 DESIGN SEISMIC HAZARDS ................................................................................. 3-1
3.2.1 Ground Shaking .............................................................................................. 3-1
3.2.1.1 Safety Evaluation Earthquake ................................................................ 3-2
3.2.1.2 Functional Evaluation Earthquake .......................................................... 3-4
3.2.1.3 Horizontal Ground Motion and Directionality Effects .............................. 3-4
3.2.1.4 Effects of Vertical Ground Excitation ...................................................... 3-5
3.2.1.5 Damping ................................................................................................. 3-5
xii SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019
3.2.2 Liquefaction .................................................................................................... 3-6

3.2.3 Fault Rupture................................................................................................... 3-7
3.2.4 Additional Seismic Hazards ............................................................................. 3-7
3.3 MATERIAL PROPERTIES ....................................................................................... 3-8
3.3.1 Expected Material Properties ........................................................................ 3-8
3.3.2 Nonlinear Reinforcing Steel Models ................................................................ 3-8
3.3.3 Reinforcing Steel ............................................................................................ 3-9
3.3.4 Nonlinear Prestressing Steel Model .............................................................. 3-11
3.3.5 Nonlinear Concrete Models ........................................................................... 3-12
3.3.6 Normal Weight Concrete ............................................................................... 3-13
3.4 EFFECTIVE SECTION PROPERTIES ................................................................. 3-15
3.4.1 General.......................................................................................................... 3-15
3.4.2 Effective Moment of Inertia for Seismic Critical Members ............................. 3-15
3.4.3 Effective Moment of Inertia for Superstructures and Cap Beams .................. 3-16
3.4.4 Effective Torsional Moment of Inertia ............................................................ 3-16
3.5 GLOBAL DISPLACEMENT CRITERIA .................................................................. 3-16
3.5.1 General.......................................................................................................... 3-16
3.5.2 Local Principal/Critical Axes .......................................................................... 3-21
3.6 LOAD AND RESISTANCE FACTORS .................................................................. 3-21
4. SEISMIC DEFORMATION DEMANDS AND ANALYSIS METHODS ........................ 4-1
4.1 GENERAL ............................................................................................................... 4-1

4.2 ANALYSIS METHODS ............................................................................................ 4-1
4.2.1 Equivalent Static Analysis ............................................................................... 4-3
4.2.2 Elastic Dynamic Analysis................................................................................. 4-4
4.2.3 Nonlinear Time History Analysis ...................................................................... 4-6
4.3 STRUCTURAL MODELING..................................................................................... 4-7
4.3.1 Global Models ................................................................................................. 4-7
4.3.2 Stand-Alone Models ...................................................................................... 4-10
4.3.2.1 Transverse Stand-Alone Models ........................................................... 4-10
4.3.2.2 Longitudinal Stand-Alone Models ......................................................... 4-10
4.4 DEFORMATION DEMANDS ................................................................................. 4-13
TABLE OF CONTENTS xiii
4.4.1 Displacement Ductility Demand ..................................................................... 4-13

4.4.2 Overstrength Demand ................................................................................... 4-14
4.4.2.1 Overstrength Moment Demand ............................................................. 4-15
4.4.2.2 Overstrength Shear Demand................................................................. 4-15
4.4.3 Superstructure and Bent Cap Seismic Demand ............................................ 4-15
4.4.3.1 Seismic Moment Demand ..................................................................... 4-15
4.4.3.2 Seismic Shear Demand ......................................................................... 4-17
4.4.4 P-∆ Effects ..................................................................................................... 4-18
5. SEISMIC DEFORMATION CAPACITIES................................................................... 5-1
5.1 GENERAL ................................................................................................................ 5-1

5.2 GLOBAL DISPLACEMENT CAPACITY ................................................................... 5-1
5.2.1 General ............................................................................................................ 5-1
5.2.2 Inelastic Static Analysis ................................................................................... 5-1
5.3 SEISMIC CRITICAL MEMBERS .............................................................................. 5-7
5.3.1 General ............................................................................................................ 5-7
5.3.2 Plastic Hinge Region ....................................................................................... 5-7
5.3.3 Axial Load Limits.............................................................................................. 5-7
5.3.4 Equivalent Plastic Hinge Length ...................................................................... 5-8
5.3.5 Confined Core ............................................................................................... 5-10
5.3.6 Flexural Capacity ........................................................................................... 5-10
5.3.6.1 Minimum Flexural Capacity ................................................................... 5-10
5.3.6.2 Moment Curvature Analysis .................................................................. 5-10
5.3.7 Shear Capacity .............................................................................................. 5-12
5.3.7.1 General ................................................................................................. 5-12
5.3.7.2 Nominal Concrete Shear Capacity ........................................................ 5-12
5.3.7.3 Nominal Shear Reinforcement Capacity ............................................... 5-14
5.3.7.4 Maximum Shear Reinforcement ............................................................ 5-15
5.3.7.5 Minimum Shear Reinforcement ............................................................. 5-15
5.3.8 Transverse Reinforcement Requirements ..................................................... 5-15
5.3.8.1 General ................................................................................................. 5-15
5.3.8.2 Minimum Transverse Reinforcement Inside the Plastic Hinge Region .. 5-16
xiv SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019
5.3.8.3 Transverse Reinforcement Outside the Plastic Hinge Region .............. 5-18
5.3.8.4 Transverse Reinforcement for Columns Supported on Type II Shafts .. 5-18
5.3.8.5 Transverse Reinforcement for Type I Shafts with Larger Shaft
Reinforcement ...................................................................................... 5-19
5.3.9 Longitudinal Reinforcement Requirements.................................................... 5-19
5.3.9.1 Maximum Longitudinal Reinforcement .................................................. 5-19
5.3.9.2 Minimum Longitudinal Reinforcement ................................................... 5-19
5.3.9.3 Minimum Size of Longitudinal Reinforcement within Interlocking
Hoops .................................................................................................... 5-19
5.4 CAPACITY PROTECTED MEMBERS................................................................... 5-21
5.4.1 General.......................................................................................................... 5-21
5.4.2 Flexural Capacity........................................................................................... 5-21
5.4.3 Shear Capacity .............................................................................................. 5-21
5.4.4 Superstructure and Bent Cap Seismic Capacity............................................ 5-22
5.4.5 Transverse Reinforcement for Type II Shafts ................................................ 5-23
6. FOUNDATIONS, ABUTMENTS AND SOIL-FOUNDATION-STRUCTURE

INTERACTION .......................................................................................................... 6-1
6.1 SOIL PROFILE CLASSIFICATION .......................................................................... 6-1

6.1.1 General............................................................................................................ 6-1
6.1.2 Class S1 Soil ................................................................................................... 6-1
6.1.3 Class S2 Soil ................................................................................................... 6-2
6.2 FOUNDATION DESIGN .......................................................................................... 6-2
6.2.1 General............................................................................................................ 6-2
6.2.2 Footings........................................................................................................... 6-2
6.2.2.1 General ................................................................................................... 6-2
6.2.2.2 Footing Joint Shear ................................................................................. 6-3
6.2.2.3 Effective Footing Width for Flexure ......................................................... 6-5
6.2.2.4 Rigid Footing Response .......................................................................... 6-5
6.2.2.5 Footings Stirrups ..................................................................................... 6-5
6.2.2.6 Spread Footings ...................................................................................... 6-7
6.2.3 Pile Foundations in Class S1 Soil.................................................................... 6-8
6.2.3.1 General ................................................................................................... 6-8
TABLE OF CONTENTS xv
6.2.3.2 Simplified Design for Piles in Class S1 Soil ............................................. 6-9

6.2.4 Pile Foundations in Class S2 Soil .................................................................. 6-11
6.2.4.1 General ................................................................................................. 6-11
6.2.4.2 Comprehensive Foundation Design ...................................................... 6-12
6.2.4.3 Scour and Liquefaction Considerations ................................................. 6-15
6.2.5 Shafts ............................................................................................................ 6-16
6.2.5.1 General ................................................................................................. 6-16
6.2.5.2 Flexure and Shear Demands on Type I Shafts...................................... 6-18
6.2.5.3 Flexure and Shear Demands on Type II Shafts..................................... 6-18
6.2.5.4 Pile and Shaft Extensions ..................................................................... 6-21
6.2.6 Lateral Stability of Piles and Shafts ............................................................... 6-21
6.3 ABUTMENTS ......................................................................................................... 6-23
6.3.1 Longitudinal Stiffness..................................................................................... 6-23
6.3.1.1 General ................................................................................................. 6-23
6.3.1.2 Bilinear Model........................................................................................ 6-23
6.3.1.3 Displacement Coefficient ....................................................................... 6-26
6.3.2 Transverse Stiffness ...................................................................................... 6-28
6.3.3 Support Length .............................................................................................. 6-29
6.3.4 Shear Key Design .......................................................................................... 6-30
6.3.5 Shear Key Reinforcement.............................................................................. 6-31
6.3.5.1 Isolated Key........................................................................................... 6-32
6.3.5.2 Monolithic Key ....................................................................................... 6-33
7. BRIDGE COMPONENTS........................................................................................... 7-1
7.1 FRAMES .................................................................................................................. 7-1

7.1.1 Frame and Bent Proportioning ......................................................................... 7-1
7.1.2 Balanced Stiffness ........................................................................................... 7-1
7.1.3 Balanced Frame Geometry.............................................................................. 7-4
7.2 SUPERSTRUCTURES ............................................................................................ 7-4
7.2.1 Girders ............................................................................................................. 7-4
7.2.1.1 Effective Superstructure Width ................................................................ 7-4
7.2.1.2 Precast Girders ....................................................................................... 7-9
xvi SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019
7.2.2 Reinforcement Requirements for Vertical Acceleration ................................. 7-12

7.2.3 Hinges ........................................................................................................... 7-14
7.2.3.1 General ................................................................................................. 7-14
7.2.3.2 Support Length Requirements in the Longitudinal Direction ................. 7-14
7.2.3.3 Shear Key Requirements in the Transverse Direction .......................... 7-16
7.2.3.4 Restrainers............................................................................................ 7-17
7.2.3.5 Pipe Seat Extenders ............................................................................. 7-19
7.2.4 Superstructure Depth .................................................................................... 7-19
7.3 BENT CAPS .......................................................................................................... 7-19
7.3.1 Integral Bent Caps......................................................................................... 7-19
7.3.2 Non-Integral Bent Caps ................................................................................. 7-19
7.3.2.1 General ................................................................................................. 7-19
7.3.2.2 Minimum Bent Cap Width ..................................................................... 7-20
7.3.3 Bent Cap Depth ............................................................................................. 7-20
7.4 SUPERSTRUCTURE JOINTS .............................................................................. 7-20
7.4.1 Joint Performance ......................................................................................... 7-20
7.4.2 Joint Proportioning ........................................................................................ 7-20
7.4.3 Minimum Bent Cap Width .............................................................................. 7-22
7.4.4 Types of Joint ................................................................................................ 7-23
7.4.4.1 "T" Joints ............................................................................................... 7-23
7.4.4.2 Knee Joints ........................................................................................... 7-23
7.4.5 Joint Shear Reinforcement ............................................................................ 7-25
7.4.5.1 Minimum Joint Shear Reinforcement .................................................... 7-25
7.4.5.2 T Joint Shear Reinforcement ................................................................ 7-26
7.4.5.3 Knee Joint Shear Reinforcement .......................................................... 7-33
7.5 BEARINGS AND EXPANSION JOINTS ................................................................ 7-42
7.5.1 Bearings ........................................................................................................ 7-42
7.5.2 Seismic Expansion Joints .............................................................................. 7-43
7.6 COLUMNS ............................................................................................................. 7-44
7.6.1 General.......................................................................................................... 7-44
7.6.2 Column Dimensions ...................................................................................... 7-46
7.6.3 Column Flares ............................................................................................... 7-46
7.6.3.1 Horizontally Isolated Column Flares...................................................... 7-46
TABLE OF CONTENTS xvii
7.6.3.2 Vertical Flare Isolation ........................................................................... 7-47

7.6.3.3 Lightly Reinforced Integral Flares .......................................................... 7-48
7.6.3.4 Flare Reinforcement .............................................................................. 7-48
7.6.4 Column Key Design ....................................................................................... 7-48
8. SEISMIC DETAILING ................................................................................................ 8-1
8.1 GENERAL ................................................................................................................ 8-1

8.2 SPLICES IN REINFORCING STEEL ....................................................................... 8-1
8.2.1 General ............................................................................................................ 8-1
8.2.2 Reinforcement Splices in Seismic Critical Members ........................................ 8-1
8.2.2.1 No-Splice Zones ...................................................................................... 8-1
8.2.2.2 Longitudinal Reinforcement ..................................................................... 8-2
8.2.2.3 Hoop Splices and Spiral Terminations .................................................... 8-3
8.2.3 Reinforcement Splices in Capacity Protected Members .................................. 8-5
8.2.3.1 General ................................................................................................... 8-5
8.2.3.2 Hoop Splices and Spiral Terminations .......................................................... 8-5
8.3 DEVELOPMENT OF LONGITUDINAL REINFORCEMENT IN SEISMIC
CRITICAL MEMBERS ............................................................................................. 8-6
8.3.1 Minimum Development Length of Longitudinal Reinforcement into Bent
Caps and Footings........................................................................................... 8-6
8.3.1.1 General ................................................................................................... 8-6
8.3.1.2 Epoxy-Coated Longitudinal Bars ............................................................. 8-6
8.3.1.3 Bundled Bars ........................................................................................... 8-7
8.3.1.4 Confinement Along Development Length ................................................ 8-7
8.3.2 Embedment Length and Clearances for Column Reinforcement
Extended into Type II Shafts............................................................................ 8-8
8.3.3 Reinforcing Bar Hooks ..................................................................................... 8-9
8.4 SPACING OF REINFORCEMENT IN SEISMIC CRITICAL MEMBERS .................. 8-9
8.4.1 Maximum Spacing of Transverse Reinforcement ............................................ 8-9
8.4.1.1 Inside the Plastic Hinge Region............................................................... 8-9
8.4.1.2 Outside the Plastic Hinge Region ............................................................ 8-9
8.4.2 Maximum and Minimum Lateral Spacing of Longitudinal Reinforcement ...... 8-10

xviii SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019
9. SLAB BRIDGES ........................................................................................................ 9-1
9.1 GENERAL ............................................................................................................... 9-1

9.2 SLAB DEPTH .......................................................................................................... 9-1
9.3 EFFECTIVE WIDTH FOR JOINT SHEAR ............................................................... 9-2
9.4 DROP CAPS............................................................................................................ 9-3
9.5 JOINT SHEAR REINFORCEMENT ......................................................................... 9-3
9.6 SLAB BRIDGE SUPPORTS .................................................................................... 9-9
9.7 SLAB BRIDGE HINGES .......................................................................................... 9-9
9.8 SPLICING OF REINFORCEMENT .......................................................................... 9-9
BIBLIOGRAPHY ........................................................................................................... R-1
APPENDIX A - SEISMIC DESIGN PROCEDURE FLOWCHART .................................A-1
APPENDIX B - DESIGN SPECTRUM DEVELOPMENT ...............................................B-1
INDEX............................................................................................................................. I-1

SECTION 1: INTRODUCTION 1-1
SECTION 1
INTRODUCTION
1.1 SCOPE C1.1

The California Department of The SDC is a compilation of seismic
Transportation (Caltrans) Seismic Design design criteria documented in various
Criteria, hereinafter referred to as the Division of Engineering Services (DES)
SDC, specifies the minimum seismic publications. The goal is to update all the
design requirements for newly designed DES seismic design publications on a
“Standard” concrete bridges. periodic basis to reflect the current state
Nonstandard bridges shall require Project of practice for seismic bridge design.
Specific Seismic Design criteria (PSDC) The SDC is intended for use on new
in addition to the SDC. A Seismic Safety bridges designed for the California State
Peer Review team shall be established for Highway System. New bridges may be
prominent or unusually complex bridges constructed by Cast-in-Place (CIP), or
requiring a PSDC. Precast (PC) with or without Accelerated
For seismic design of steel bridges, the Bridge Construction (ABC). Designers
Caltrans Seismic Design Specifications should refer to DES manuals for seismic
for Steel Bridges (Caltrans, 2016) shall design guidance and standards not
explicitly addressed by the SDC.
apply.
Standard bridges may be either
“Ordinary” or “Recovery” as specified in
Sections 1.2 and 1.2.1.
For the procedure to establish Project
Specific Seismic Design Criteria (PSDC),
refer to MTD 20-11. For information on
Seismic Safety Peer Review, refer to
MTD 20-16.
The term “shall” denotes a
requirement for compliance with these
Criteria.
The term “should” indicates a strong
preference for a given criterion.
The term “may” indicates a criterion
that is usable, but other local and suitably
documented, verified, and approved
criterion may also be used in a manner
consistent with SDC design philosophy.
The term “recommended” is used to
give guidance based on past
experiences.

1-2 SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019
Throughout this document, the term

“AASHTO-CA BDS” represents the
current California approved AASHTO
LRFD Bridge Design Specifications, and
the corresponding California
Amendments to AASHTO LRFD Bridge
Design Specifications.
1.2 BRIDGE CATEGORIES C1.2

All bridges shall be categorized as: The main difference between an
• Ordinary, Ordinary Standard bridge and a Recovery
• Recovery, or Standard bridge is the performance
• Important. criteria (see Section 1.3).
Depending on their bridge features,

Ordinary and Recovery bridges shall be
classified as either “Standard” or
“Nonstandard,” as follows:
• Ordinary Standard bridge,
• Ordinary Nonstandard bridge,
• Recovery Standard bridge, or
• Recovery Nonstandard bridge
1.2.1 Standard Bridge Features C1.2.1

Standard bridges shall have the The bulleted listing are the basic
following features: features of Standard (i.e., Ordinary
• Each span length less than 300 Standard and Recovery Standard)
feet, bridges. Standard bridges possess other
• Either box girder, slab on girder, or features which are common to all bridge
slab superstructures, types.
• Either solid column-type or pile- Bridges located within 300 feet of
bent substructures, active faults (per the Alquist-Priolo
• Fundamental period of the bridge Earthquake Fault Zoning Act) are
system is greater than or equal to susceptible to unusually large
0.7 seconds in the transverse and deformation demands due to near fault
longitudinal directions of the effects and are analyzed and designed for
bridge. fault-crossing hazard as established
• Bridge site is more than 300 feet through a PSDC (See also MTD 20-8).
away from a fault

1.2.2 Nonstandard Bridge Features C1.2.2

Bridges that do not satisfy any one of Nonstandard bridge features may lead
the Standard bridge features specified in to bridges with complex or non-ductile
Section 1.2.1 shall be classified as response during earthquakes.
Nonstandard. Nonstandard bridges may require a more
detailed analysis than that described in
the SDC in order to capture their complex
response.
Examples of Nonstandard bridge
features are:
Irregular Geometry
• Multiple superstructure levels
• Bifurcating superstructures
• Skew angles (greater than 20°)
that vary from support to support,
excluding curved bridges with
circular or square columns
• Hollow columns
Unusual Framing
• Outrigger and C bent supports
• Unsymmetrical layout of columns
within a bent
• Unbalanced mass and/or stiffness
distribution
• Multiple superstructure types
• Pier walls
• Isolation bearings and dampers
• Single column bents supported on
spread footings
Unusually complex bridges
• Cable-stayed
• Suspension
• Arch
• Truss
Uncommon bridge Substructure
(Foundation)
• Micropiles
• Hollow concrete piles
• Other nonstandard piles such as
timber, tapered, and composite
piles

Unusual Soil/Hazard
• Class S2 soil that has been
modified (See Section 6.1.3 for
definition of class S2 soil)
• Tsunami
• Lateral spreading induced by
liquefaction
Pier walls are nonstandard because

adequate ductility cannot be achieved in
the wall’s strong direction. When the
Hydraulics Engineer recommends the use
of pier walls such as in waterway
crossings per MTD 16-1, sacrificial guide
walls are recommended in combination
with ductile columns.
Pier walls may be needed in bridge
retrofits and/or widenings to match
existing bridge configuration and ensure
predictable seismic performance.
1.2.3 Important Bridges C1.2.3

Important bridges shall satisfy one or Designating a bridge as Important can
more of the following: have a significant implication with respect
(a) Expected to provide immediate to cost. By 2017, Caltrans had
access to emergency and similar designated only two new bridges as
life-safety facilities after an Important, namely: the New Benicia-
earthquake Martinez Bridge and the New East Span
(b) Time to restore functionality after of San-Francisco-Oakland Bay Bridge.
closure would create a major
economic impact
(c) Formally designated as critical by a
local emergency management
plan
Important bridges shall be designated
by the sponsoring district or local agency,
in consultation with Caltrans Division of
Engineering Services.

1.2.4 Recovery Bridges C1.2.4

Recovery bridges shall serve as vital Recovery bridges serve a critical role
links for rebuilding damaged areas and in the economic recovery of an area
provide access to the public shortly after impacted by a damaging earthquake.
an earthquake. They are designed for enhanced
Recovery bridges shall be designated performance above Ordinary bridges but
by the sponsoring district or local agency, less than the performance of Important
in consultation with Caltrans Division of bridges.
Engineering Services.
1.2.5 Ordinary Bridges

All bridges not designated as either
Important or Recovery shall be
designated as Ordinary.
1.3 SEISMIC PERFORMANCE C1.3

CRITERIA
The expected post-earthquake
The seismic hazard evaluation level damage states and service levels
for designing Ordinary bridges shall be corresponding to the seismic hazard
the Safety Evaluation Earthquake (SEE) evaluation levels are also shown in Table
as specified in Table 1.3-1 and Section 1.3-1.
3.2.1.1. The expected post-earthquake
The seismic hazard evaluation level damage states and service levels of
for designing Recovery bridges shall be Important bridges are included in Table
both the Safety Evaluation Earthquake as 1.3-1 to provide an indication of their
specified in Table 1.3-1 and Section expected performance relative to other
3.2.1.1 and the Functional Evaluation bridge categories. It should be noted that
Earthquake (FEE) as specified in Table the design spectra for Safety and
1.3-1 and Section 3.2.1.2. Functional Evaluation
Table 1.3-1: Seismic Hazard Evaluation Levels and Expected Performance

EXPECTED POST EXPECTED POST
BRIDGE SEISMIC HAZARD
EARTHQUAKE EARTHQUAKE
CATEGORY EVALUATION LEVEL
DAMAGE STATE SERVICE LEVEL
Ordinary SEE Major No Service
Limited Service-
SEE Moderate
weeks
Recovery
FEE Minimal Full Service
SEE Minimal to Moderate Limited Service-days

Important
FEE None to Minimal Full Service

Ordinary and Recovery bridges Earthquakes for an Important bridge

subjected to the seismic hazard levels are defined by a PSDC and are typically
specified in Table 1.3-1 shall satisfy the greater than those for Ordinary and
displacement criteria specified in Section Recovery bridges.
3.5.1 and the displacement ductility
demand, μD specified in Table 4.4.1-1. Expected Post-earthquake Damage
States
• Major – Bridge replacement is
likely. All plastic hinges within the
structure have formed with ductility
demand values approaching the
limits specified in Table 4.4.1-1.
Bridges near the epicenter of the
1000-year event are expected to
experience major damage but
bridges farther away are expected
to experience moderate or minimal
damage.
• Moderate – Bridge repair is likely,
but bridge replacement is unlikely
• Minimal – Essentially elastic
performance
• None – No damage
Major, Moderate, and Minimal

damage states may be correlated to the
following damage states proposed by
Vosooghi and Saiidi (2010):
• Major damage: Damage State 5
(DS-5) - “imminent failure,” i.e.,
onset of compressive failure of
core concrete
• Moderate damage: DS-3 -
“extensive cracks and spalling”
and DS-4 - “visible lateral and/or
longitudinal reinforcing bars”
• Minimal damage: DS-1 - “flexural
cracks” and DS-2 - “minor spalling
and possible shear cracks”

Expected Post-earthquake Service

Levels
• No Service – Bridge is closed for
repair or replacement.
• Limited Service – weeks: Bridge is
open for emergency vehicle traffic;
A reduced number of lanes for
normal traffic is available within ten
weeks of the earthquake; Vehicle
weight restriction may be imposed
until repairs are completed. It is
expected that within ten weeks of
the earthquake, repair works on a
damaged bridge would have
reached the stage that would
permit normal traffic on at least
some portion of the bridge.
• Limited Service – days: Bridge is
open for emergency vehicle traffic;
A reduced number of lanes for
normal traffic is available within a
couple of days of the earthquake;
Vehicle weight restriction may be
imposed until repairs are
completed. It is expected that a
bridge inspection would have been
completed within a couple of days
of the earthquake.
• Full Service – Full access to
normal traffic is available almost
immediately after the earthquake.

1.4 DESIGN PHILOSOPHY C1.4

Ordinary and Recovery bridges shall The “strong beam - weak column”
be designed based on “strong beam - proportioning principle, otherwise known
weak column” proportioning principle. as capacity design, entails that certain
Plastic hinging shall be directed to bridge members (generically represented
Seismic Critical Members (SCMs), by seismic critical members) are
allowing a mechanism to form and intentionally designed for energy
facilitates transverse and longitudinal dissipation/damping while other members
movement of bridge bents and frames. (the capacity protected members) are
The plastic hinge ductility or other means intentionally designed to remain
of energy dissipation/bridge damping essentially elastic when the design
shall be adequate to satisfy the seismic hazards (DSH) occur. See
deformation demands imposed by the Sections 2.1 and 3.2 for definition and
Design Seismic Hazards (DSH). specification of DSH.
When the design seismic hazards for In general, energy dissipation may be
life safety (i.e., the safety evaluation achieved by the formation of flexural
earthquake) occur, ordinary bridges may plastic hinges in seismic critical members,
experience major damage requiring failure of sacrificial elements such as
bridge replacement but shall have a shear keys, abutment backwalls,
minimal probability of collapse. conventional expansion joints, link
When the design seismic hazards for beams, and elastomeric bearings, the
life safety occur, recovery bridges may mobilization of soil behind abutment
experience moderate damage requiring backwalls and around foundation
bridge repair but shall have a minimal elements, and the use of isolation devices
probability of bridge replacement. When and dampers. Although sacrificial
subjected to the design seismic hazard elements are prone to being damaged
that has a significant chance of occurring during design level earthquakes, they
during the life of the bridge (i.e., the provide longitudinal and transverse
functional evaluation earthquake), resistance for service loads and small to
recovery bridges shall respond in an moderate earthquakes, and their failure is
essentially elastic manner with minimal associated with energy dissipation and a
bridge damage. consequent limitation of the forces
Every bridge shall be designed with an transmitted to bridge substructures.
Earthquake Resisting System that Additional provisions and commentary on
ensures a load path for gravity loads and sacrificial elements are given in Sections
provides sufficient strength and ductility to 6.3.4, C6.3.4, 7.5.1 and C7.5.1.
achieve the performance criteria specified In order to ensure failure by inelastic
in Section 1.3. flexural yielding while minimizing the
chance of non-ductile failure modes,
SCMs are designed for high ductility by
providing the potential plastic hinge
locations with enhanced lateral
confinement which acts to maintain the
integrity of the confined core of the SCM
enabling it to sustain high strain levels as
well as prevent premature buckling of the
longitudinal bars.
Except as specified below, Caltrans takes advantage of ductility

Earthquake Resisting Systems shall and post elastic strength to meet the
consist of the following: performance criteria specified in Section
• Seismic critical members 1.3 with a minimum of capital investment.
(SCMs) – ductile structural This philosophy is based on achieving a
members that are intentionally balance between the acceptable risk level
designed to deform inelastically and the initial cost of a bridge.
through several cycles without Force-based design of SCMs using
significant loss of strength, thereby Design Spectrum (DS) forces is
limiting the forces transmitted to considered an exception to SDC design
adjoining capacity protected philosophy.
members, Significant inelastic response in
• Capacity protected members concrete superstructures is not desirable
(CPMs) - structural members that because of the potential to jeopardize
remain essentially elastic after the public safety and the difficulty in repairing
adjoining members fuse or form such damage, especially for continuous
plastic hinges, bridges.
• Earthquake resisting elements Seismic critical members and capacity
(EREs) – bridge elements or protected members are listed in Sections
portions of bridge members that 5.3.1 and 5.4.1, respectively. Additional
undergo inelastic deformation, provisions for earthquake resisting
dissipate energy, or increase elements are given in Section 3.1.
bridge damping, and Bridge accessories such as
• Sacrificial elements – Bridge soundwalls, lighting poles, and sign
elements that are typically structures are not considered a part of the
designed to disengage in order to earthquake resisting system.
limit forces transmitted to adjoining Experimental and analytical
capacity-protected members. investigations (Wibowo et al., 2013) have
The earthquake resisting system for shown that seismic response is minimally
single span bridges may be achieved affected by live load.
without seismic critical members. A seismic design flowchart intended to
Live load shall not be applied serve as a procedural guide for the
simultaneously with seismic loading. engineer using the SDC seismic design
philosophy to design a Standard Bridge is
shown in Appendix C. The list of
processes in the flowchart is only typical
and is not intended to be an exhaustive
listing of the processes required by the
SDC for the seismic design of every
Standard bridge.

1.5 PROCEDURE FOR MODIFYING C1.5

THE SDC In Figure 1.5-1, the abbreviations
Modification to the SDC shall include represent the following Caltrans entities:
addition of new SDC provisions, removal
of existing SDC provisions or revision of EQC = Earthquake Committee,
existing SDC provisions. The steps to TSC = Technical Steering
modify the SDC shall be as summarized Committee,
in Figure 1.5-1. OEEAR = Office of Earthquake
Engineering, Analysis and
Research,
SQM = Structure Quality
Management,
SC = Structure Construction, and
SBE = State Bridge Engineer.
Additional information on the

procedure for modifying the SDC can be
found in MTD 20-11.

Sponsor submits draft SDC

modification to EQC Chairperson
EQC votes on proposal or forms a

Study Team to evaluate the proposal
EQC NO
Is proposal
acceptable?
YES
SDC Development Branch of

DES SQM and SC No modification
OEEAR implements
comment on proposed modifications to the SDC
recommendation(s)
NO TSC
Did modifications follow Quality
Management Plan?
YES
OEEAR Office Chief forwards

modifications to SBE
SBE may seek input SBE may seek

from Structure Policy input from Seismic
Board Advisory Board
REVISE SBE NO
Are modifications
acceptable?
YES
SBE issues an Implementation memo to

approve new SDC modifications
Figure 1.5-1 Flowchart for Modifying the SDC

This page intentionally left blank

SECTION 2: DEFINITIONS, NOTATIONS, AND ACRONYMS 2-1
SECTION 2
DEFINITIONS, NOTATIONS, AND ACRONYMS/INITIALISMS
2.1 DEFINITIONS
Bent – A bridge component consisting of cap beam, columns/pile extensions, shafts,

footings and/or pile group. Some bridges may be analyzed in the transverse direction using
the bent model with its tributary bridge mass.
Bridge Accessories – Appurtenant equipment and components attached to the bridge

structure such as sign structures, crash cushions, hand railings, soundwalls, and lighting
poles.
Bridge System – A structural system consisting of superstructure, substructure,

foundations and abutments framed into a single or multiple frame structural system. An
example of a bridge system is a slab bridge composed of a slab superstructure supported
by multi-column bents on pile/shaft extension foundations and abutments.
Capacity Design – A design philosophy in which certain bridge components are

intentionally designed for energy dissipation/damping while adjoining components are
intentionally designed to remain essentially elastic. Energy absorption may occur by
yielding and/or disengaging.
Capacity Protected Member – A structural member within a bridge system that remains
essentially elastic after the adjoining members fuse or form plastic hinges.
Confined Concrete – Concrete in a structural member which is confined by a combination

of two or more of the following types of reinforcement: longitudinal reinforcement, closely
spaced butt-spliced hoops, cross-ties with seismic hooks, and closely spaced continuous
spirals.
Confinement – The use of reinforcing, steel or composite fiber wrapping, or similar devices
to produce lateral and/or circumferential pressures that prevent disintegration of concrete
in a structural member subjected to deformation.
Critical Pile Length – The embedded length of pile for which greater lengths do not result
in a reduction of 5% or more in the deflection at the pile/shaft cut-off elevation in a lateral
stability analysis.

Curvature – A measure of flexural deformation defined as the reciprocal of the radius of

curvature of the neutral axis of a member in bending. Curvature is mathematically
calculated as the ratio of the extreme fiber strain to the distance from the neutral axis to
the extreme fiber.
Design Seismic Hazards – The collection of seismic hazards at a bridge site used in the
design of bridges. Such hazards consist of ground shaking (i.e. Design Spectrum), surface
fault rupture, liquefaction, lateral spreading, and tsunami.
Design Spectrum – The acceleration response spectrum used in design to characterize

the ground shaking hazard at a bridge site. Also, see definition of Response Spectrum.
Ductile Member – A structural member that can deform inelastically for several cycles
without significant degradation of strength under the demands generated by the design
seismic hazards.
Earthquake-Resisting Elements – bridge elements that undergo inelastic deformation,

dissipate energy, or increase bridge damping under the deformation demands imposed by
the design seismic hazards.
Earthquake-Resisting System – A system that provides sufficient strength and ductility

for the bridge, ensures a load path for gravity loads, and controls seismic displacements.
Energy Dissipation Devices – Energy-dissipating elements introduced between bridge

components for the purpose of increasing the bridge damping, resulting in a decrease in
superstructure displacement and hence a decrease in the ductility demand on the
supporting seismic critical members.
Equivalent Plastic Hinge Length – The equivalent length of a plastic-hinging member

over which the plastic curvature is assumed constant for estimating plastic rotation.
Essentially Elastic – State of deformation of a bridge member limited to minor cracking

or spalling of cover concrete.
Expected Material Properties – The most probable material properties (as opposed to
specified minimum material properties) used to provide a more realistic estimate of
member design strength and deformation capacity.

Functional Evaluation Earthquake (FEE) – A seismic hazard design Spectrum that has
a relatively small magnitude but may occur several times during the life of the bridge. FEE
is taken as a spectrum based on a 20% probability of exceedance in 50 years (or 225-year
return period).
Global Behavior – The response of a bridge system including the effects of adjacent
components, subsystems, and/or boundary conditions. For example, the behavior of an
entire bridge system.
Ground Shaking – Seismic hazard measured by ground motion time histories or response
spectrum.
Joint Shear – Vertical and horizontal shear forces developed in moment-resisting beam-
to-column or footing-to-column joints subjected to seismic deformation.
Liquefaction – Loss of shear strength in loose, cohesionless soil resulting from build-up
of pore water pressure as the soil tries to consolidate when exposed to seismic vibrations.
Local Behavior – The response of an individual component or subsystem independent of

the effects of adjacent components, subsystems, or boundary conditions. For example,
the behavior of an individual bent or column.
No-Splice Zone – Region(s) of a seismic-critical member identified on bridge plans, where

splicing of the main flexural reinforcement is prohibited.
Overstrength Moment – The expected maximum moment that a seismic critical member
can develop, taken as 120 % of the idealized plastic moment capacity of the seismic critical
member. Adjacent capacity protected members are designed to remain essentially elastic
when the adjoining seismic critical member reaches its overstrength moment.
Overstrength Shear – Shear force associated with the overstrength moment, taken as
120 % of the plastic shear demand of the seismic critical member. Adjacent capacity
protected members are designed to remain essentially elastic when the adjoining seismic
critical member reaches its overstrength shear.
Plastic Hinge – The region of a structural member that undergoes flexural yielding and
plastic rotation while retaining flexural strength.
Plastic Hinge Region – Region of a structural member expected to form a plastic hinge
and requiring special detailing in the form of enhanced confinement.

Prestress Secondary Moments and Shears – Moments and shears induced by support
restraints in a statically indeterminate prestressed frame.
Project Specific Seismic Design Criteria (PSDC) – Seismic design criteria for bridges
with nonstandard features as defined by the SDC. A PSDC consists of the SDC and the
specific criteria developed by the PSDC team for the nonstandard feature(s).
Pushover Analysis – An inelastic static analysis procedure used to evaluate the

displacement capacity of a structure or frame.
Response Spectrum – A plot showing peak responses (acceleration, velocity, or

displacement) of bridges idealized as single degree of freedom oscillators versus the
periods of the bridges.
Sacrificial Elements – Bridge elements that are typically designed to disengage in order
to limit forces in adjoining capacity-protected members. Sacrificial elements include shear
keys, backwalls, joints, and bearings.
Safety Evaluation Earthquake (SEE) – A seismic hazard design spectrum that has a
small probability of occurring during the life of the bridge. SEE is taken as a spectrum
based on a 5% probability of exceedance in 50 years (or 975-year return period). This
design spectrum is practically equivalent to that based on a 7% probability of exceedance
in 75 years life of a bridge.
Seismic Critical Member – A ductile structural member intentionally designed to deform

inelastically through several cycles without significant degradation of strength, thereby
limiting the forces transmitted to adjoining capacity protected members.
Seismic Isolation – A design approach in which a bearing device with an energy

dissipation characteristic is used to reduce seismic design forces by increasing the period
of a relatively stiff bridge.
Specified Material Properties – Nominal or specified minimum material properties as

provided by design codes or ASTM. Corresponding values of expected material properties
are obtained by multiplying the nominal values by a factor greater than 1.0.
Standard Bridge – An Ordinary or Recovery bridge possessing all the standard bridge
features listed in Section 1.2.1 but not any of the nonstandard bridge features.

Type I Shaft – A drilled shaft foundation having the same confined core diameter as that
of the supported column but may have the same or different concrete cover and area of
transverse and longitudinal reinforcement as the supported column.
Type II Shaft – A drilled shaft foundation that is at least 24 inches larger than the maximum
dimension of the supported column and has a reinforcing cage diameter larger than that of
the supported column.
Ultimate Curvature Capacity – The curvature at which the concrete reaches its ultimate
compression strain or the longitudinal reinforcing steel reaches its reduced ultimate tensile
strain.
Unconfined Concrete – Concrete without special confinement detailing as defined for

Confined concrete.
Volumetric ratio of transverse reinforcement – the ratio of volume of transverse

reinforcement to the core volume confined by the transverse reinforcement (measured out-
to-out).

2.2 NOTATIONS
A = cross sectional area of hollow steel section (Section C7.2.3.3)

Ab = cross sectional area of an individual reinforcing steel bar (Sections 5.3.7.3, C5.3.8.2,
C6.3.5, 9.5)
top
Acap = area of bent cap top flexural steel (Sections 7.4.5.2, 7.4.5.3); area of top flexural
reinforcement in each direction of slab superstructure within the effective width
(Section 9.5)
bot
Acap = area of bent cap bottom flexural steel (Sections 7.4.5.2, 7.4.5.3); area of bottom
flexural reinforcement in each direction of slab superstructure within the effective
width (Section 9.5)
Acv = area of concrete engaged in interface shear transfer (Sections 6.3.5.2, 7.6.4)
Ae = effective shear area (Sections 5.3.7.2, 5.3.7.4)
Ag = gross cross-sectional area (Sections C3.4.2, 5.3.3, 5.3.7.2, 5.3.9.1, 5.3.9.2)
Ajh = effective horizontal area of a moment resisting joint (Sections 7.4.2, 9.5)
ftg
Ajh = effective horizontal area at mid-depth of the footing, assuming a 45° spread away
from the boundary of the column in all directions (Section 6.2.2.2)
Ajv = effective vertical joint area for a moment resisting joint (Sections 7.4.2, 9.5)
jh
As = area of horizontal stirrups or ties required at moment resisting joints (Sections
7.4.5.2, 7.4.5.3); total area of horizontal ties in the effective width of slab
superstructure along the longitudinal direction (Section 9.5)
jhc
As = total area of horizontal ties placed at the end of the bent cap in Case 1 Knee joints
(Section 7.4.5.3); total area of horizontal end ties along the transverse direction for
slab superstructure knee joints (Section 9.5)
jv
As = area of vertical stirrups or ties required at moment resisting joints (Sections 7.4.5.2,
7.4.5.3); total area of vertical stirrups in each of the Joint Region and Joint Perimeter
of a slab superstructure (Section 9.5)
j-bar
As = area of vertical “J” bar reinforcement required at moment resisting joints with a skew
angle greater than 20° (Sections 7.4.5.2, 7.4.5.3); area of “J” shaped bars inside the
Core Region of a slab superstructure above the SCM (Section 9.5)
sj
As = total area of bent cap side face reinforcement required at moment resisting joints
(Sections 7.4.5.2, 7.4.5.3, 9.5)
Ask = area of interface shear reinforcement crossing the shear plane (Sections 6.3.5.1,
7.6.4)

Ast = total area of column longitudinal reinforcement anchored in the joint (Sections
7.4.5.2, 7.4.5.3, 8.3.1.4, 9.5); total cross-sectional area of column longitudinal
reinforcement (Sections C3.4.2, C5.3.8.2)
Ast,max = maximum area of longitudinal reinforcement allowed in a seismic critical member
(Section 5.3.9.1)
Ast,min = minimum area of longitudinal reinforcement allowed in a seismic critical member
(Section 5.3.9.2)
u-bar
As = area of bent cap top and bottom reinforcement bent in the form of “U” bars in Knee
joints (Section 7.4.5.3); area of additional bent cap reinforcement (u-shaped) for
knee joints in the transverse direction of slab superstructures (Section 9.5)
Ash = area of horizontal shear key reinforcement in the stem wall (Section 6.3.5.1)
Ask = area of interface shear key reinforcement (Section 7.6.4)
AIso
sk = area of interface shear reinforcement required for isolated shear key (Section
6.3.5.1)
AIso
sk(provided) = area of interface shear reinforcement provided for isolated shear key (Section
6.3.5.1)
Amono
sk = area of interface shear reinforcement required for monolithic shear key (Section
6.3.5.2)
Amono
sk(provided) = area of interface shear reinforcement provided for monolithic shear key
(Section 6.3.5.2)
Av = area of shear reinforcement perpendicular to the flexural tension reinforcement
(Sections 5.3.7.3, 5.3.7.5, C5.3.8.2, 9.5)
Av,joint = seismic critical member transverse reinforcement in the joint region of slab
superstructures (Section 9.5)
a = vertical distance from the location of the applied force on the shear key to the top
surface of the stem wall (Section C6.3.5.1); thickness of joint filler (Sections 6.3.3,
7.2.3.2) Bc = column cross-sectional dimension perpendicular to the direction of
bending (Section 6.2.2.2)
Bcap = bent cap width (Sections 7.4.2, 7.4.3)
Beff = effective width of the superstructure for resisting longitudinal seismic moments
(Section 7.2.1.1)
ftg
Beff = effective width of footing for calculating average normal stress in the vertical
direction within a footing moment resisting joint (Section 6.2.2.2)
slab
Beff = effective width of slab superstructure (Section 9.3)
b = vertical distance from the top surface of the stem wall to the centroid of the lowest
layer of shear key horizontal reinforcement (Section C6.3.5.1)

pile
C(i) = axial compression force demand on a pile (Section 6.2.3.2)
c = damping ratio (Section 3.2.1.5)
Dc = column cross-sectional dimension parallel to the direction of bending (Sections
6.2.2.2, 7.2.1.1, 7.4.2, 7.6.2, 8.3.1.4, 9.3, C9.5); diameter or cross-sectional
dimension of column in the direction of the cap width or length (Sections 7.4.3,
7.4.4.2, 7.4.5.2, 7.4.5.3)
Dc.g = distance from the top of column to the center of gravity of the superstructure (Section
4.4.3.1)
Dc,max = largest cross-sectional dimension of a seismic critical member (Sections 5.3.8.5,
8.3.2)
Dftg = depth of footing (Sections 6.2.2.2, 6.2.2.4, 6.2.3.2, C6.2.4.2, 7.6.2)
Ds = depth of superstructure at the bent cap (Sections 6.3.3, 7.2.1.1, 7.2.2, 7.2.3.2, 7.4.2,
7.6.2); depth of slab at the seismic critical member support (Sections 9.3, 9.5)
D’ = cross-sectional dimension of confined concrete core measured between the
centerlines of the peripheral hoop or spiral reinforcement (Sections 5.3.7.3, 5.3.7.5,
C5.3.8.2)
D’c = confined column cross-section dimension, measured out to out of ties, in the
direction parallel to the axis of bending (Section C5.3.8.2)
D* = diameter for circular shafts (Section 5.3.4)
Dn = thickness of layer n (Section Appendix B)
db = nominal reinforcing bar diameter (Sections 6.3.5, 8.3.3)
dbl = nominal bar diameter of longitudinal reinforcement (Sections 5.3.4, 8.3.1.1, 8.3.2,
9.2)
d(i)x = distance from pile (i) to the centerline of the column along the X axis (Section
6.2.3.2)
d(i)y = distance from pile (i) to the centerline of the column along the Y axis (Section
6.2.3.2)
Ec = modulus of elasticity of concrete (Sections 3.3.6, 3.4.2, 3.4.1)
Es = Modulus of elasticity of steel (Sections 3.3.3, 3.3.4)
Fabut = idealized ultimate passive capacity of the backfill behind abutment backwall or
diaphragm (Section 6.3.1.2)
Fbw = idealized ultimate passive capacity of the backfill behind seat abutment backwall
(Section 6.3.1.2)
Fdia = idealized ultimate passive capacity of the backfill behind diaphragm abutment
(Section 6.3.1.2)
Fsk = abutment shear key force demand (Sections 6.3.4, 6.3.5.1)

Fu = specified tensile strength of steel (Section C7.2.3.3)

f’c = specified compressive strength of unconfined concrete (Sections 3.3.1, 3.3.6,
C3.4.2, 5.3.3, 5.3.7.2, 5.3.7.4, 6.2.2.2, 7.4.2, 7.4.5.1, 7.6.4)
f’cc = compressive strength of confined concrete (Section 3.3.6)
f’ce = expected compressive strength of unconfined concrete (Sections 3.3.1, 3.3.6)
fh = average normal stress in the horizontal direction within a moment resisting joint
(Section 7.4.2)
fh = tensile stress for 7-wire low relaxation prestress strand (Section 3.3.4)
fu = specified minimum tensile strength of reinforcement (Sections 3.3.3, 3.3.4)
fue = expected tensile strength of reinforcement (Section 3.3.3)
fv = average normal stress in the vertical direction within a moment resisting joint
(Sections 6.2.2.2, 7.4.2)
fy = specified minimum yield strength of reinforcement (Sections 3.3.1, 7.6.4)
fye = expected yield strength of reinforcement (Sections 3.3.1, 5.3.4, 6.3.5.1)
fyh = specified minimum yield strength of transverse column reinforcement (Sections
5.3.7.2, 5.3.7.3, 5.3.7.5, 7.4.5.1)
G = gap between the isolated flare and soffit of the bent cap; gap between the steel
jacket and soffit of the bent cap or top of the footing (Sections 5.3.4, 7.6.3.1)
Gc = shear modulus (modulus of rigidity) for concrete (Sections 3.3.6, 3.4.1)
g = acceleration due to gravity (Sections C4.2.1, 7.2.2)
Ho-max = length of shaft/column from point of maximum moment to point of contraflexure
above ground considering the base of plastic hinge at the point of maximum moment
(Section 5.3.4)
habut = height of abutment backwall or diaphragm (Section 6.3.1.2)
hbw = abutment backwall height for seat abutment (Section 6.3.1.2)
hdia* = height of diaphragm abutment if not designed for full soil pressure (Section 6.3.1.2)
hdia** = height of diaphragm abutment if designed for full soil pressure (Section 6.3.1.2)
I = moment of inertia (Section 3.4.1)
Ieff = effective moment of inertia for computing member stiffness (Sections 3.4.2, C3.4.3)
Ig = moment of inertia about centroidal axis of the gross section of a member (Sections
C3.4.2, 3.4.3)
Ip.g.(x) = moment of inertia of the pile group about the X axis (Sections 6.2.3.2, C6.2.4.2)
Ip.g.(y) = moment of inertia of the pile group about the Y axis (Sections 6.2.3.2, C6.2.4.2)
J = torsional moment of inertia for computing member stiffness (Section 3.4.1)
Jeff = effective torsional moment of inertia for computing member stiffness (Section 3.4.4)

Jg = gross torsional moment of inertia about centroidal axis of a member (Section 3.4.4)
K = effective stiffness of a bent or frame (Section 4.2.1)
Kabut = abutment longitudinal stiffness (Section 6.3.1.2)
Keff = effective abutment longitudinal stiffness (Sections 4.2.1, C4.2.1, 6.3.1.2, 6.3.1.3)
adj
Kef = effective abutment longitudinal stiffness adjusted for displacement coefficient
(Section 6.3.1.3)
Knom = nominal abutment transverse stiffness (Section 6.3.2)
Kres = residual stiffness for assessing abutment effectiveness (Section 6.3.1.3)
e
ki = effective stiffness of bent or column i (Section 7.1.2)
e
kj = effective stiffness of bent or column j (Section 7.1.2)
Kθ = abutment longitudinal stiffness for theta degree skewed abutment (Section 6.3.1.2)
L = member length from the point of maximum moment to the point of contra-flexure
(Sections C5.2.2, 5.3.4); portion of the shaft length measured from the center of the
plastic hinge to the center of gravity of the superstructure (Section C5.2.2); pad
dimension along the bridge for elastomeric bearings, or length of masonry plate for
PTFE bearings (Section 6.3.3)
Lcol = length of column (Section C6.2.6)
Lftg = cantilever length of the footing or pile cap measured from face of column to edge of
footing along the principal axis of the footing (Section 6.2.2.4)
Lmin = minimum horizontal distance from the vertical shear key bars to the hooked or
headed end of the lowest layer of hanger bars for isolated shear key (Section
C6.3.5.1)
Lmp = length of masonry plate for the bearing (Section 7.2.3.2)
Lp = equivalent plastic hinge length (Sections C5.2.2, 5.3.4)
Lpile = length of pile/shaft (Section 6.2.6)
Lpr = region(s) of a structural member member expected to form plastic hinge(s) (Section
5.3.2)
lac = minimum length of longitudinal reinforcement in seismic critical members extended
into cap beams or footings (Sections 8.3.1.1, 8.3.1.4)
lac,provided = actual length of column longitudinal reinforcement embedded into the bent cap
(Sections 7.4.2, 7.4.5.2, 7.4.5.3, 9.5)
ld = development length in tension of straight bars (Section 7.4.5.3)
ldb = basic tension development length (Section 7.2.2)
ldh = development length in tension of standard hooked bars (Section C6.3.5.1)
M = moment (Section 5.3.6.2)

MR = movement range (Sections 6.3.3, 7.2.3.2)

MD = moment demand at any location of a Type II shaft generated by the column’s
overstrength moment and associated shear (Section 6.2.5.3)
R
MD = moment demand on the right side of superstructure-to-column joint (Section 4.4.3.1)
L
MD = moment demand on the left side of superstructure-to-column joint (Section 4.4.3.1)
R
Mdl = dead load plus added dead load moments on the right side of superstructure-to-
column joint (Sections 4.4.3.1, 5.4.4)
L
Mdl = dead load plus added dead load moments on the left side of superstructure-to-
col-top
Mdl = dead load plus added dead load moments on the top of column (Section 4.4.3.1)
col-top
Meq = seismic moment at the top of column (Sections 4.4.3.1, 4.4.3.2)
R
Meq = earthquake moment distributed to the right side of superstructure-to-column joint
(Sections 4.4.3.1, 5.4.4)
L
Meq = earthquake moment distributed to the left side of superstructure-to-column joint
(Sections 4.4.3.1, 5.4.4)
Mmax = maximum moment demand in Type II shaft (Section 6.2.5.3)
Mn = nominal moment capacity based on the specified minimum concrete and steel
strengths when the concrete strain reaches 0.003 (Section C4.4.4)
Mne = nominal moment capacity based on expected material properties and a concrete
strain of 0.003 (Sections 5.3.6.2, 5.4.2, 6.2.5.3)
Mne,slab = nominal moment capacity of a slab superstructure based on expected material
properties and a concrete strain of 0.003 (Section 9.5)
sup(R)
Mne = nominal moment capacity of the adjacent right superstructure span based on
expected material properties and a concrete strain of 0.003 (Section 5.4.4)
sup(L)
Mne = nominal moment capacity of the adjacent left superstructure span based on
expected material properties and a concrete strain of 0.003 (Section 5.4.4)
col
Mo = overstrength moment of a seismic critical member (Sections 4.4.2.1, 4.4.2.2,
6.2.5.3, 7.4.1, 7.4.2, 7.6.4)
col-top
Mo = column overstrength moment on the top of column (Section 4.4.3.1)
col
Mo(x) = component of the column overstrength moment demand about the X axis (Sections
6.2.3.2, C6.2.4.2)
col
Mo(y) = component of the column overstrength moment demand about the Y axis (Sections
6.2.3.2, C6.2.4.2)

Mp = idealized plastic moment capacity calculated by M-ϕ analysis (Sections C4.4.4,

C6.2.3.2)
col
Mp = idealized plastic moment capacity of a seismic critical member calculated by M-ϕ
analysis (Sections 4.4.2.1, 4.4.4, 5.3.2, 5.3.6.2, 9.5)
col-top
Mp/s = effective secondary prestress moment on the top of column (Section 4.4.3.1)
R
Mp/s = effective secondary prestress moment (after losses have occurred) on the right side
of superstructure-to-column joint (Sections 4.4.3.1, 5.4.4)
L
Mp/s = effective secondary prestress moment (after losses have occurred) on the left side
of superstructure-to-column joint (Sections 4.4.3.1, 5.4.4)
pile
Mp(x) = component of the pile plastic moment capacity at the pile cap connection due to total
average axial load about the X axis (Section C6.2.4.2)
pile
Mp(y) = component of the pile plastic moment capacity at the pile cap connection due to total
average axial load about the Y axis (Section C6.2.4.2)
Mu = ultimate moment capacity of a seismic critical member (Section C4.4.4)
My = moment of a seismic critical member corresponding to the first reinforcing bar yield
(Sections 3.4.2, C4.4.4, 5.3.6.2)
M-ϕ = moment curvature analysis (Sections 3.4.2, C5.2.2, 5.3.6.2, 5.4.2)
mi = tributary mass of bent or column i (Section 7.1.2)
mj = tributary mass of bent or column j (Section 7.1.2)
N = blow count per foot for the California Standard Penetration Test (Section Appendix
Figure B.10)
NA = abutment support length normal to centerline of bearing (Section 6.3.3)
NH = support length normal to the centerline of bearing (Section 7.2.3.2)
Np = total number of piles in the pile group (Sections 6.2.3.2, C6.2.4.2)
(N1)60 = penetration resistance corrected for overburden pressure and hammer efficiency
(Section 6.1.2)
n = number of individual interlocking spirals or hoops in the core of the sections (Section
5.3.7.3); total number of piles at distance d(i)x or d(i)y from the centroid of the pile
group (Section 6.2.3.2)
P = absolute value of the net axial force normal to the shear plane (Section 7.6.4); axial
compressive force (Section C3.4.2)
Pb = beam axial force (including prestressing) at the center of a moment-resisting joint
(Section 7.4.2)
Pc = axial force on a seismic critical member including the effects of overturning (Sections
5.3.3, 5.3.7.2, 6.2.2.2, 7.4.2)

Pdl = axial load due to dead load (Sections 4.4.4, 5.3.3); superstructure dead load
reaction at the abutment plus the weight of the abutment and its footing (Section
6.3.4)
sup
Pdl = superstructure axial load reaction at the abutment (Sections 4.3.1, 6.3.4)
Pp = total axial load on the pile group including column axial load (dead load + EQ load
due to any overturning effects), footing weight, and overburden soil weight (Sections
6.2.3.2, C6.2.4.2)
pc = nominal principal compression stress in a joint (Sections 6.2.2.2, 7.4.2)
pt = nominal principal tension stress in a joint (Sections 6.2.2.2, 7.4.2, 7.4.5.1)
RA = abutment displacement coefficient (Sections C4.2.1, 6.3.1.3)
RD = displacement reduction factor for damping ratios exceeding 5% (Section 3.2.1.5)
Rsk = skew reduction factor (Section 6.3.1.2)
RRup = site to rupture plane distance (Section Appendix B)
S = cap beam short stub length (Section 7.4.4.2)
Sd = 5% damped spectral displacement (Section 3.2.1.5)
S’d = spectral displacement modified for higher levels of damping (Section 3.2.1.5)
Sa = design spectral acceleration coefficient at the structure period (Section 4.2.1)
s = spacing of shear/transverse reinforcement measured along the longitudinal axis of
the structural member (Sections 5.3.7.3, 5.3.7.5, C5.3.8.2)
su = undrained shear strength (Section 6.1.2, Appendix Figure B.10)
Ti = natural period of frame i (Sections 7.1.3, C7.2.3.2)
Tj = natural period of frame j (Sections 7.1.3, C7.2.3.2)
col
Tc = total tensile force in column longitudinal reinforcement associated with Mo
(Sections 6.2.2.2, 7.4.2)
pile
T(i) = axial tension force demand on a pile (Sections 6.2.2.2, 6.2.3.2)
Tjv = net tensile force in moment resisting footing joints (Section 6.2.2.2)
V = shear capacity of hollow structural section (Section C7.2.3.3)
Vc = nominal shear capacity provided by concrete (Section 5.3.7)
VD = shear demand at any location of a Type II shaft generated by the column’s
overstrength moment and associated shear (Section 6.2.5.3)
R
VD = shear demand on the right side of superstructure-to-column joint (Sections 4.4.3.1,
4.4.3.2)
L
VD = shear demand on the left side of superstructure-to-column joint (Sections 4.4.3.1,
4.4.3.2)

R
Vdl = dead load plus added dead load shears on the right side of superstructure-to-column
joint (Sections 4.4.3.2, 5.4.4)
L
Vdl = dead load plus added dead load shears on the left side of superstructure-to-
col-top
Vdl = dead load plus added dead load shear on the top of column (Section 4.4.3.2)
Ve = maximum elastic lateral force (Section C4.2)
l
Veq = seismic shear on the left side of superstructure-to-column joint (Sections 4.4.3.2,
5.4.4)
R
Veq = seismic shear on the right side of superstructure-to-column joint (Sections 4.4.3.2,
5.4.4)
col-top
Veq = shear force at the top of column due to seismic (Sections 4.4.3.1, 4.4.3.2)
Vmax = maximum shear demand in Type II shaft (Section 6.2.5.3)
Vn = nominal shear capacity (Sections 5.3.7, 5.4.3, 6.2.5.3)
sup(r)
Vn = nominal shear capacity of the adjacent right superstructure span (Section 5.4.4)
sup(L)
Vn = nominal shear capacity of the adjacent left superstructure span (Section 5.4.4)
col
Vo = overstrength shear force (Sections 4.4.2.2, 5.3.7, 6.2.3.2, 6.2.5.3, 7.4.1, 7.6.4)
col-top
Vo = overstrength shear on the top of column (Section 4.4.3.2)
col
Vo(x) = component of column overstrength shear demand along the X axis (Section
C6.2.4.2)
col
Vo(y) = component of column overstrength shear demand along the Y axis (Section
C6.2.4.2)
Vp = inelastic lateral force (Section C4.2)
L
Vp/s = effective secondary prestress shear (after losses have occurred) on the left side of
superstructure-to-column joint (Sections 4.4.3.2, 5.4.4)
R
Vp/s = effective secondary prestress shear (after losses have occurred) on the right side of
superstructure-to-column joint (Sections 4.4.3.2, 5.4.4)
col-top
Vp/s = effective secondary prestress shear on the top of column (Section 4.4.3.2)
Vpiles = sum of lateral capacity of the piles (Section 6.3.4)
col
Vp = plastic shear capacity corresponding to the idealized plastic moment capacity of a
SCM (Section C4.4.2.2)
Vs = nominal shear capacity provided by shear reinforcement (Sections 5.3.7, 5.3.7.3,
5.3.7.4)
Vww = shear capacity of one wingwall (Section 6.3.4)

v = Poisson’s ratio (Section 3.3.6)

vc = permissible concrete shear stress (Section 5.3.7.2)
vjv = nominal shear stress in the vertical direction within a moment resisting joint
(Sections 6.2.2.2, 7.4.2)
vs = shear wave velocity (Section 6.1.2, Appendix B)
vn = shear wave velocity of layer n (Section Appendix B)
vs30 = shear wave velocity for the upper 30 m of the soil profile (Section Appendix B)
W = tributary weight of the structure (Section 4.2.1)
w = unit weight of concrete (Section 3.3.6)
wabut= abutment width along the skew direction (Section 6.3.1.2)
wbw = width of backwall for seat abutment (Section 6.3.1.2)
wcap = width of drop cap (Sections 9.3, C9.5)
wdia = width of diaphragm abutment (Section 6.3.1.2)
Z = depth to rock parameter (Section Appendix B)
Z1.0 = depth to 1.0 km/s shear wave velocity (Section Appendix B)
Z2.5 = depth to 2.5 km/s shear wave velocity (Section Appendix B)
α = adjustment factor for shear key force demand (Section 6.3.4)
Δ = deflection (Section 4.4.4); deflection at pile cut-off elevation (Section C6.2.6)
Δabut = abutment displacement at idealized yield (Section 6.3.1.2)
Δb = displacement due to flexibility of capacity protected members (Section 3.5.1)
Δc = local displacement capacity (Section C5.2.2)
Δcol = displacement due to the elastic and plastic deformation of the column (Section 3.5.1)
ΔC = frame or bent displacement capacity in the local principal/critical axis of member
(Sections 3.5.1, 5.2.2); support length of abutment or in-span hinge (Section 3.5.1)
Δcr+sh = relative displacement due to creep and shrinkage (Sections 6.3.3, 7.2.3.2)
Δd = local member displacement demand (Section 5.3.7.2)
ΔD = frame or bent displacement demand in the local principal/critical axis of member
(Sections 3.5.1, 4.2, 4.4.1, 4.4.4, 6.3.1.3)
ΔD1 and ΔD2 = earthquake displacement demands on either side of an in-span hinge
(Section 7.2.3.2)
Δeff = effective abutment longitudinal displacement (Sections 6.3.1.2, 6.3.1.3)
Δeq = displacement demand for the frame adjacent to the abutment (Section 6.3.3);
relative longitudinal earthquake displacement demand at an expansion joint
(Section 7.2.3.2)
Δf = displacement due to foundation flexibility (Section 3.5.1)

Δgap = width of expansion gap at seat abutment (Sections 6.3.1.2, C6.3.1.2)

Δmax,elastic = displacement corresponding to maximum elastic lateral force (Section C4.2)
Δmax,inelastic = displacement corresponding to maximum inelastic lateral force (Section C4.2)
Δp = idealized plastic displacement capacity due to rotation of the plastic hinge (Section
C5.2.2)
Δp/s = relative displacement due to pre-stress shortening (Sections 6.3.3, 7.2.3.2)
Δp* = plastic displacement (Section 3.5.1)
Δr = relative lateral offset between the point of contra-flexure and the base of the plastic
hinge (Section 4.4.4)
Δs = shaft displacement at the point of maximum moment (Section 4.4.4)
Δtemp = relative displacement due to thermal expansion and contraction (Sections 6.3.3,
7.2.3.2)
Δcol
Y = idealized yield displacement of a seismic critical member (Sections 3.5.1, C5.2.2)
ΔY(i) = frame or bent displacement at the instant a plastic hinge forms in the i-th seismic
critical member (Sections 4.4.1, 5.3.7.2)
εcc = compressive strain at maximum compressive stress of confined concrete (Section
3.3.6)
εco = unconfined concrete compressive strain at the maximum compressive stress
(Section 3.3.6)
εsp = ultimate compressive strain (spalling strain) of unconfined concrete (Section 3.3.6)
εcu = ultimate compression strain for confined concrete (Section 3.3.6)
εps = tensile strain for 7-wire low relaxation prestress strand (Section 3.3.4)
εps,EE = tensile strain in prestress steel at the essentially elastic limit state (Section 3.3.4)
R
εps,u = reduced ultimate tensile strain in prestress steel (Section 3.3.4)
εsh = tensile strain at the onset of strain hardening for A706 reinforcement (Section 3.3.3)
εsu = ultimate tensile strain for A706 reinforcement (Section 3.3.3)
R
εsu = reduced ultimate tensile strain for A706 reinforcement (Sections 3.3.3, 5.4.2)
εy = nominal yield strain for A706 reinforcement (Section 3.3.3)
εye = expected yield strain for A706 reinforcement (Section 3.3.3)
θ = angular difference between the local and global directions (Section C4.2.2);
abutment skew angle (Sections 6.3.1.2, 6.3.3, C7.2.3.2)
θp = plastic hinge rotation capacity (Section C5.2.2)
λ = load reduction factor for a pile group (Section 6.2.3.2)
μc = local displacement ductility capacity (Section C5.2.2)
μD = displacement ductility demand (Sections 4.4.1, 5.3.7.2)

μd = local displacement ductility demand (Section 5.3.7.2)

ρc = axial load ratio due to dead load and overturning (Section 5.3.3)
ρdl = axial load ratio due to dead load (Sections 5.3.3, 5.3.8.2)
ρl = percent longitudinal reinforcement ratio (Section 5.3.8.2)
ρs = volumetric ratio of transverse reinforcement (Sections 5.3.7.2, C5.3.8.2, 7.4.5.1,
8.3.1.4)
ρsT = volumetric ratio of column transverse reinforcement extended into a T joint region
(Section 7.4.5.2)
ρsknee = volumetric ratio of column transverse reinforcement extended into a Knee joint
region (Section 7.4.5.3)
ϕ = load and resistance factor (Sections 3.6, 5.3.7, 5.4.4, 6.2.5.3, 7.6.4)
ϕp = idealized plastic curvature capacity (Section C5.2.2)
ϕu = ultimate curvature capacity defined as the curvature when the concrete reaches the
ultimate compression strain εcu or the longitudinal reinforcing steel reaches the
R
reduced ultimate strain εsu (Sections C3.5.1, 5.2.2, C5.2.2, 5.3.6.2)
ϕY = idealized yield curvature defined by an elastic- perfectly plastic M-ϕ curve of the
cross section (Sections C5.2.2, 5.3.6.2)
ϕy = yield curvature corresponding to the first yield of the reinforcement (Sections 3.4.2,
5.3.6.2)

2.3 ACRONYMS AND INITIALISMS
ABC = Accelerated Bridge Construction (Section C1.1)

AASHTO = American Association of State Highway and Transportation Officials (Sections
C1.1, C8.3.1.1, C8.3.2)
AASHTO-CA BDS = current California approved AASHTO LRFD Bridge Design
Specifications, and the corresponding California Amendments to AASHTO LRFD
Bridge Design Specifications (Sections C1.1, 5.4.2, 5.4.3, 6.2.2.1, 6.2.2.6, C6.2.2.6,
C6.2.4.3, C6.2.5.1, C6.3.4, C6.3.5.1, C6.3.5.2, 7.2.2, 7.3.1, 7.6.4,8.4.1.2, 8.4.2)
ASTM = American Society for Testing and Materials (Sections 2.1, C3.3.1, 3.3.3, C3.3.3,
C3.3.4, 5.3.4, C6.1.2)
BDA = Bridge Design Aids (Sections C7.2.3.3, C7.2.3.4, 9.1, C9.5)
Caltrans = California Department of Transportation (Sections 1.1, 1.2.3, C1.2.3, 1.2.4,
C1.4, C1.5, 3.2.1, C3.2.1.1, C3.3.3, C3.3.6, C4.2, C5.2.2, C5.3.6.2, 6.2.3.2, 6.2.4.1,
C8.1, Appendix B)
CIDH = Cast-in-drilled-hole (Sections 5.4.5, C6.2.5.1, 6.2.5.3, 6.2.6)
CIP = Cast-in-place (Sections C1.1, C7.2.1.2, 7.2.2, C9.6)
CISS = Cast-in-steel-shell pile (Sections 5.3.4, 5.4.5, C6.2.5.1, 6.2.5.3)
CPM = Capacity Protected Member (Sections 1.4, 5.4.1, 5.4.2, 5.4.3, 8.2.3.1)
CQC3 = Complete Quadratic Combination 3 (Sections 4.2.2, C4.2.2)
DES = Caltrans’ Division of Engineering Service (Section 1.1)
DS = Design Spectrum (Sections C1.4, 3.2.1); Damage State (Sections C1.3, C3.5.1)
DSH = Design Seismic Hazards (Sections 1.4, C1.4, 3.1, 3.2, C4.3.1)
EDA = Elastic Dynamic Analysis (Sections 3.5.2, 4.2, C4.2, C4.2.1, 4.2.2, C4.2.3, 4.3.1,
6.3.1.1, C6.3.1.1, C7.2.3.3, C7.2.3.4)
EQC = Earthquake Committee (Sections 1.5, C1.5)
ERE = Earthquake Resisting Element (Sections 1.4, 3.1, C3.1)
ESA = Equivalent Static Analysis (Sections C3.5.1, 3.5.2, 4.2, C4.2, 4.2.1, C4.2.1,
C4.2.3, 4.3.1, 5.2.2, C5.2.2, 6.3.1.1, C6.3.1.1, C7.2.3.3)
FEE = Functional Evaluation Earthquake (Sections 1.3, 2.1, 3.2.1.2, C3.2.1.2, 4.4.1,
7.5.2)
ISA = Inelastic Static Analysis (Sections 5.2.2, C5.2.2, 6.2.4.2, 6.3.1.1, C6.3.1.1)
METS = Caltrans Materials Engineering and Testing Services (Section C3.3.3)

MTD = Caltrans Bridge Memo to Designers (Sections C1.1, C1.2.1, C1.2.2, C1.5, C3.2.2,
C3.2.3, C4.2.2, C4.2.3, C6.2.3.2, C6.2.5.1, C6.3.4, C7.5.1, C7.6.3.4, C9.6)
NTHA = Nonlinear Time History Analysis (Sections 3.5.2, 4.2, C4.2, C4.2.1, 4.2.3, C4.2.3,
4.3.1, C6.3.1.1, Appendix A)
OEEAR = Office of Earthquake Engineering, Analysis and Research (Sections 1.5, C1.5,
C4.2)
PC = Precast (Sections C1.1, 7.2.1.2, 7.2.2)
PGA = Peak Ground Acceleration (Sections 7.2.1.2, C7.2.1.2, Appendix A)
PSDC = Project Specific Seismic Design Criteria (Sections 1.1, C1.1, C1.2.1, C1.3, 2.1,
3.2.1.5, C3.2.1.5, 3.2.4, 3.3.3, C3.3.3, 5.3.1, C5.3.8.2, 6.2.4.3, C7.2.3.2, C7.5.1)
P/S = Prestressed (Concrete or Strand) (Sections 4.4.3.1, 6.3.3, 7.2.3.2)
PTFE = Polytetrafluoroethylene (spherical bearings) (Sections 6.3.3, C6.3.3, 7.2.3.1,
7.5.1, C7.5.1)
SBE = State Bridge Engineer (Sections 1.5, C1.5)
SC = Structure Construction (Sections 1.5, C1.5)
SCM = Seismic Critical Member (Sections 1.4, C1.4, 2.1, 3.1, C3.3.1, 3.3.3, C3.3.3, 3.4.2,
3.4.4, 4.4.1, C4.4.1, 4.4.2, 4.4.2.1, C4.4.2.1, 4.4.2.2, C4.4.2.2, 4.4.4, C5.2.2, 5.3.1,
C5.3.1, 5.3.2, C5.3.2, 5.3.3, C5.3.3, 5.3.6.2, 5.3.4, C5.3.4, C5.3.5, C5.3.6.2, 5.3.7.1,
5.3.7.2, 5.3.7.5, 5.3.8.1, C5.3.8.1, 5.3.8.2, C5.3.8.2, 5.3.9.1, 5.3.9.2, 5.3.9.3, 5.4.1,
C5.4.1, 5.4.4, 6.2.5.4, 7.2.1.2, 7.3.1, C7.3.3, C7.4.2, 7.4.5.2, C7.4.5.2. 7.4.5.3,
C7.4.5.3, 8.2.2.1, C8.2.2.1, 8.2.2.2, 8.2.2.3, C8.2.2.3, 8.3.1.1, 8.3.1.3, 8.3.1.4,
8.4.1.2, 8.4.2, 9.2, C9.2, 9.3, 9.4, C9.4, 9.5, C9.5, Appendix A)
SDC = Seismic Design Criteria (Sections 1.1, C1.1, C1.2.2, C1.4, 1.5, C1.5, 2.1, C3.2.1.1,
C4.2, 4.3.2, C5.3.8.2, C6.1.1, 6.2.1, C7.5.1, C8.3.2, 9.1, Appendix A, Appendix B)
SEE = Safety Evaluation Earthquake (Sections 1.3, 2.1, 3.2.1.1, C3.2.1.1, 4.4.1)
SQM = Structure Quality Management (Sections 1.5, C1.5)
SRSS = Square Root of Sum of Squares (Section 4.2.2)
Sup = Superstructure (Sections 5.4.4, 7.6.2)
TSC = Technical Steering Committee (Sections 1.5, C1.5)

This page is intentionally left blank.

SECTION 3: GENERAL REQUIREMENTS 3-1
SECTION 3
GENERAL REQUIREMENTS
3.1 EARTHQUAKE RESISTING C3.1

ELEMENTS
Earthquake Resisting Elements Refer to Figure C3.1-1 for locations of
(EREs) shall be used within the EREs within earthquake resisting
earthquake resisting system to dissipate systems.
energy or increase the bridge damping Nonstandard EREs include seismic
during the design seismic hazards. Where isolation bearings and energy dissipation
applicable, EREs shall undergo inelastic devices such as dampers, which limit the
deformation without causing structure inertial forces transferred between the
collapse. superstructure and substructure.
Standard EREs include plastic hinges Type I shafts may hinge below the
in seismic critical members (SCMs), and ground line. However, their use is not
soil behind abutment backwalls, as shown subject to the exception procedure
in Figure 3.1-1. because of their robust ductile behavior
Earthquake resisting elements should coupled with the fact that the foundation
be accessible for inspection and repair. soil could be excavated to access and
Devices that may prevent plastic repair the plastic hinge.
hinging/ dissipation of energy shall not be Devices such as barrier rails, may
attached to, bored into, or cast into the disrupt the performance of plastic hinges.
potential plastic hinge locations of a SCM.
3.2 DESIGN SEISMIC HAZARDS

The Design Seismic Hazards (DSH)
shall include ground shaking, surface fault
rupture, and their associated effects such
as liquefaction, lateral spreading, and
tsunami.
3.2.1 Ground Shaking C3.2.1

Ground shaking shall be characterized The design spectrum reflects the
for design by the Design Spectrum (DS). shaking hazard at or near the ground
The design spectrum shall be based on surface.
the most current Caltrans approved U.S. For Design Spectrum development,
Geological Survey Seismic Hazard Maps. refer to Appendix B.
A qualified geo-professional shall provide
final design spectrum recommendations.

3.2.1.1 Safety Evaluation Earthquake C3.2.1.1

The Design Spectrum for Safety The SEE represents a rare ground motion
Evaluation Earthquake (SEE) shall be that may occur during the life of the
taken as a spectrum based on a 5% structure. Larger ground motions are
probability of exceedance in 50 years (or possible.
975-year return period).
Figure 3.1-1: Examples of Earthquake Resisting Elements

Figure C3.1-1: Locations of Standard Earthquake Resisting Elements in Earthquake

Resisting Systems
The design spectrum based on a 5%

probability of exceedance in 50 years is,
for all practical purposes, equivalent to
that based on a 7% probability of
exceedance in 75 years. The latter
matches the 75 years design life of a
bridge.
A web-based design tool is available
for use in the specification of the design
spectrum:
(http://dap3.dot.ca.gov/ARS_Online/).
The technical references link at this
website contains links to several helpful
documents including Caltrans’ fault
database and a link to the USGS
Interactive Deaggregation website.
Several aspects of design spectrum
development require special knowledge
related to the determination of fault
location (utilization of original source
mapping where appropriate) and
interpretation of the site profile and
geologic setting for incorporation of site
effects.

A detailed discussion of the

development of the probabilistic design
spectra as well as possible adjustment
factors is given in Appendix B.
The deterministic criterion used in
previous editions of the SDC as one of the
parameters in the definition of design
spectrum was dropped in the current SDC
2.0. Recent seismic source models for
California include a much broader range
of considered rupture scenarios making
selection of Mmax somewhat arbitrary.
Furthermore, performance-based
earthquake engineering relies on
probabilistic estimates of demand and
capacity, therefore deterministic
measures are unsuitable. In the case of a
rare earthquake on a fault considered to
be inactive, SDC compliant bridges have
ample reserve capacity to prevent
collapse.
3.2.1.2 Functional Evaluation Earthquake C3.2.1.2

The Design Spectrum for Functional The FEE represents an earthquake
Evaluation Earthquake (FEE) shall be that has a significant chance of occurring
taken as a spectrum based on a 20 % during the lifespan of a bridge.
probability of exceedance in 50 years (or The FEE can be obtained using the
225-year return period). USGS Interactive Deaggregation website
(https://earthquake.usgs.gov/hazards/int
eractive/). The FEE spectrum is
constructed by running the deaggregation
tool for 20% exceedance in 50-year
hazard for each of the ten available
spectral periods. Intermediate periods
can be obtained using linear interpolation.
3.2.1.3 Horizontal Ground Motion and C3.2.1.3

Directionality Effects
In determining seismic displacement
demands, uncertainty in directionality
effects of horizontal ground motion shall
be accounted for as specified in Sections
4.2.1, 4.2.2, and 4.2.3.

Except for cases of near-fault shaking

(generally, site to fault distances less than
15.5 miles (25 km)), earthquake ground
shaking hazard has a random orientation
and may be equally probable in all
horizontal directions. The method for
obtaining the maximum demands on
bridge members due to the directionality
of ground shaking depends on the
analysis method and complexity of the
bridge. Refer to Section 4.2 for analysis
methods.
3.2.1.4 Effects of Vertical Ground

Excitation
The effects of vertical ground
excitation shall be estimated by applying
an equivalent static vertical load to the
superstructure as specified in Section
7.2.2.
3.2.1.5 Damping C3.2.1.5

A 5% damped elastic response Damping ratios on the order of 10%
spectrum shall be used for determining can be justified for bridges that are heavily
seismic demand. A PSDC shall be influenced by energy dissipation at the
required to use damping ratios other than abutments and are expected to respond
5%. like single-degree-of-freedom systems. If
allowed via the PSDC procedure, a
reduction to the 5% damped spectral
displacement may be applied as shown in
Equation C3.2.1.5-1.
S'd = (RD ) × (Sd ) (C3.2.1.5-1)
where:
1.5
RD = [40c+1]
+ 0.5 (C3.2.1.5-2)
S’d = spectral displacement modified for

higher levels of damping
Sd = 5% damped spectral displacement
RD = displacement reduction factor for
damping ratios exceeding 5%
c = damping ratio (0.05 ≤ c ≤ 0.1)

The following characteristics are

typically good indicators that higher
damping may be anticipated:
• Total length less than 300 feet,
• Three spans or less,
• Abutments designed for sustained
soil mobilization,
• Skew less than or equal to 20
degrees, and
• Continuous superstructure without
in-span hinges or expansion joints.
Abutments that are designed to fuse

(seat type abutment with backwalls), or
respond in a flexible manner, may not
develop enough sustained soil-structure
interaction to rely on the higher damping
ratio.
3.2.2 Liquefaction C3.2.2

The liquefaction potential within the When locations are identified as being
project site shall be investigated. Bridges susceptible to liquefaction and/or lateral
subject to liquefaction shall be analyzed spreading, the geo-professional should
and designed as specified in Section provide recommendations that include a
6.2.4.3. discussion of the following:
• Potential horizontal and vertical
ground displacements
• Possible remediation strategies
including ground improvement,
avoidance, and/or structural
modification
For additional information on

quantifying the impacts of soil liquefaction
and lateral spreading, see MTD 20-14
and 20-15.

3.2.3 Fault Rupture C3.2.3

The potential for fault rupture below or Preliminary investigation of fault
near the bridge shall be considered. rupture hazard includes the identification
of nearby active surface faults that may
cross beneath a bridge or proposed
bridge, per MTD 20-10. If a fault trace
underlies a structure or the structure falls
within the specified fault zone, then the
geo-professional will provide the following
recommendations:
• Location and orientation of fault
traces or zones with respect to
structures,
• Expected horizontal and vertical
displacements, and
• Description of additional
evaluations or investigations that
could refine the above information.
Refer to Caltrans Geotechnical

Manual for additional information on fault
rupture.
3.2.4 Additional Seismic Hazards

Other seismic hazards that are
identified at a project site shall be
assessed in accordance with the PSDC
procedure.

3.3 MATERIAL PROPERTIES

3.3.1 Expected Material Properties C3.3.1
The capacity of reinforced and Use of expected material strengths
prestressed concrete components to instead of specified strengths provides a
resist all seismic demands except shear, realistic estimate for design strength
shall be based on expected material (Unanwa and Mahan, 2014). An expected
properties (i.e., expected compressive concrete compressive strength, f’ce
strength of unconfined concrete, f’ce and recognizes the typically conservative
expected yield strength of reinforcement, nature of concrete batch design, and the
fye). expected strength gain with age. Also,
Seismic shear capacity shall be based given that the specified minimum yield
on the specified material strengths (i.e., strength fy for ASTM A706 Grade 60 steel
specified minimum yield strength for steel can range between 60 ksi and 78 ksi while
reinforcement, fy, and specified that of ASTM A706 Grade 80 steel can
compressive strength of unconfined range between 80 ksi and 98 ksi, an
concrete, f’c). expected reinforcement yield strength, fye
better represents the actual strength than
the specified minimum of 60 ksi or 80 ksi.
The possibility that the yield strength may
be less than fye in seismic critical
members (SCMs) will conservatively
impact capacity protected components.
The possibility that the yield strength may
be less than fye in capacity protected
members is accounted for in the
overstrength magnifier specified in
Section 4.4.2.1.
3.3.2 Nonlinear Reinforcing Steel C3.3.2

Models
Reinforcing steel shall be modeled The strain-hardening curve can be
with a stress-strain relationship that modeled as a parabola or other non-linear
exhibits an initial linear elastic portion, a relationship and should terminate at the
yield plateau, and a strain hardening ultimate tensile strain, εsu. The ultimate
range in which the stress increases with strain is set at the strain at peak stress.
the strain, as shown in Figure 3.3.2-1. The The length of the yield plateau is a
yield point shall be defined by the function of the steel strength and bar size.
expected yield strength of the steel, fye.

Figure 3.3.2-1 Steel Stress-Strain Model
3.3.3 Reinforcing Steel C3.3.3

ASTM A706 reinforcing steel shall be Grade 80 bars are not to be used in
used for seismic applications, as follows: SCMs until definitive data from ongoing
• ASTM A706 Grade 60 – for all research become available.
applications, including use in Use of Grade 80 reinforcing steel for
SCMs and capacity protected headed bar terminations, hooks, and
couplers may be permitted on a project
members. Hooks, headed bar
specific basis (PSDC) based on
terminations, and splices shall be availability of specific project data.
allowed. The properties for A706 Grade 60
• ASTM A706 Grade 80 – for straight reinforcing steel were established on the
bars in capacity protected basis of data from a collection of mill
members only. A PSDC shall be certificates and augmented by testing
conducted by Caltrans Material
required to use Grade 80
Engineering and Testing Services
reinforcing steel for hooks, headed (METS).
bar terminations, splices, and With the exception of the reduced
couplers. ultimate tensile strain, εsuR
, the properties
The properties of ASTM Grades 60 for A706 Grade 80 reinforcing steel are
and 80 reinforcing steel, as specified in based on a number of monotonic pull
Table 3.3.3-1, shall be used. Additional tests obtained through a Caltrans-funded
test data, if available, may be used in-lieu research project (Overby et al., 2015).
of those specified in Table 3.3.3-1 subject
to the PSDC procedure.
For design purposes, the reduced
R
ultimate tensile strain, εsu instead of the
ultimate tensile strain, εsu shall be used.
The reduced ultimate strain instead of

the ultimate tensile strain is used for
design in order to decrease the probability
of fracture of the reinforcement. For
Grade 60 steel, the ultimate tensile strain
was reduced by up to thirty-three percent
to obtain the reduced ultimate strain. For
Grade 80 reinforcement, a value of 0.084
R
for εsu was proposed by Overby et al.
(2015) based on the 5th percentile of the
R
test results. The specified εsu value of 6%
for Grade 80 reinforcement was adopted
in order to be conservative.
Table 3.3.3-1 Properties of ASTM A706 Grades 60 and 80 Reinforcing Steel
Property Grade 60 Grade 80
Modulus of elasticity, Es 29,000 ksi 29,000 ksi
Specified minimum yield strength, fy 60 ksi 80 ksi
Expected yield strength, fye 68 ksi 85 ksi
Specified minimum tensile strength, fu 80 ksi 98 ksi
Expected tensile strength, fue 95 ksi 112 ksi
Nominal yield strain, εy 0.0021 0.0028
Expected yield strain, εye 0.0023 0.0033
Ultimate tensile strain, εsu 0.120 - #10 bars and smaller 0.095
0.090 - #11 bars and larger
R
Reduced ultimate tensile strain, εsu 0.090 - #10 bars and smaller 0.060
0.060 - #11 bars and larger
Strain at onset of strain hardening, εsh 0.0150 - #8 bars 0.0074

0.0125 - #9 bars
0.0115 - #10 & #11 bars
0.0075 - #14 bars
0.0050 - #18 bars

3.3.4 Nonlinear Prestressing Steel C3.3.4

Model
Prestressing steel shall be modeled Figure 3.3.4-1 is an idealized stress-
with a nonlinear stress strain model, as strain model for 7-wire low-relaxation
shown in Figure 3.3.4-1. prestressing strand.
The curves in Figure 3.3.4-1 may be For material properties pertaining to
approximated by Equations 3.3.4-1 to high strength bars, refer to ASTM A722 -
3.3.4-4. Approximate yield prestress steel Standard Specification for High-Strength
strain, εps,EE Steel Bars for Prestressed Concrete.
0.0076 for fu = 250 ksi

εps,EE = �
0.0086 for fu = 270 ksi
Reduced ultimate prestress steel strain,

εR
ps,u
εR
ps,u = 0.03
250 ksi Strand:
εps ≤ 0.0076: fps = 28500εps (3.3.4-1)
0.25
εps ≥ 0.0076: fps = 250 - � ε � (3.3.4-2)
ps
270 ksi Strand:
εps ≤ 0.0086: fps = 28500εps (3.3.4-3)
0.04
εps ≥ 0.0086: fps = 270 - εps - 0.007
(3.3.4-4)
where:
εps = tensile strain for 7-wire low
relaxation prestress strand
fps = tensile strain for 7-wire low
relaxation prestress steel strand
(ksi)

Figure 3.3.4-1 Prestressing Strand Stress Strain Model
3.3.5 Nonlinear Concrete Models C3.3.5

Mander’s stress-strain model, as In Figure 3.3.5-1, the initial ascending
shown in Figure 3.3.5-1, shall be used to curve may be represented by the same
determine the capacity of concrete equation for both the confined and
members. unconfined model since the confining
steel has no effect in this range of strains.
The confined concrete model continues to
ascend until the confined compressive
strength, f’cc is reached. This segment is
followed by a descending curve
dependent on the parameters of the
confining steel. The ultimate strain, εcu is
the point where strain energy equilibrium
is reached between the concrete and the
confinement steel.
Additional information on Mander’s
stress-strain model is available in Mander
et al. (1988a).

3.3.6 Normal Weight Concrete C3.3.6

Properties of normal weight concrete Typical values for the ultimate
shall be taken as specified in Table 3.3.6- compression strain, εcu range from 0.012
1. to 0.05, depending on the amount of
Values of confined compressive transverse confinement reinforcement
strain, εcc and ultimate compression strain (Priestley et al. 1996).
for confined concrete, εcu shall be defined
by Mander’s constitutive stress strain
model for confined concrete.
Figure 3.3.5-1 Concrete Stress Strain Model (Mander, 1988a)

Table 3.3.6-1 Properties of Normal Weight Concrete
Property Design Value Equation No.
Modulus of Elasticity Ec = 33w1.5 �f'ce (3.3.6-1)
where:
Ec = modulus of elasticity of
concrete (psi)
w = unit weight of concrete (lb/ft3)
f'ce = expected compressive strength

of unconfined concrete (psi)
Shear Modulus Ec (3.3.6-2)

Gc =
2(1+vc )
Poisson’s Ratio v = 0.2 (3.3.6-3)
Expected Concrete f'ce = 1.3f'c but not less than 5000 psi (3.3.6-4)
Compressive Strength
Unconfined concrete εco = 0.002 (3.3.6-5)

compressive strain at the
maximum compressive stress
Ultimate unconfined εsp = 0.005 (3.3.6-6)

compressive strain (spalling)
Confined compressive strain εcc - defined by Mander’s model
Ultimate compression strain εcu - defined by Mander’s model

for confined concrete

3.4 EFFECTIVE SECTION PROPERTIES

3.4.1 General C3.4.1
Section properties, flexural rigidity EcI Concrete members display nonlinear
and torsional rigidity, GcJ shall reflect the response before reaching their idealized
cracking that occurs before yield is yield limit state.
reached.
3.4.2 Effective Moment of Inertia for C3.4.2

Seismic Critical Members
The effective moment of inertia, Ieff for M-ϕ curve is obtained from cross-
SCMs shall be determined from the section analysis as specified in Section
secant slope of the Moment-Curvature 5.3.6.2.
(M-ϕ) curve between the origin and the For preliminary design, Ieff may be
point designating the first reinforcing bar estimated as:
yield as:
P
- 0.05
f 'c Ag
My Ieff = �A+ (B - A)� Ig ≤ B Ig
Ec Ieff = (3.4.2-1) 0.2
ϕy
(C3.4.2-1)
where:
in which:
My = moment of the section at first yield
of the reinforcing steel (lb-in.) A = 0.32 + 12 � Ast − 0.01�
A
(C3.4.2-2)
g
ϕy = yield curvature (rad/in)
A
Ieff = effective moment of inertia (in.4) B = 0.42 + 9 � Ast − 0.01� (C3.4.2-3)
g
where:
P = axial compressive force (lb)
f 'c = specified minimum compressive
strength of unconfined concrete
(psi)
Ag = gross cross section area (in.2)
Ast = total area of longitudinal
reinforcement in the section (in.2)
Equations C3.4.2-1 to C3.4.2-3 were
derived from the effective stiffness charts
developed by Nuncio-Cantera and
Priestley (1991) for axial load ratios,
�P ⁄ f 'c Ag � less than or equal to 0.25.

3.4.3 Effective Moment of Inertia for C3.4.3

Superstructures and Cap Beams The lower bound represents lightly
The effective moment of inertia for reinforced sections and the upper bound
reinforced concrete sections may be represents heavily reinforced sections.
estimated between 0.5Ig - 0.75Ig, where Ieff in reinforced concrete
Ig is the gross section moment of inertia. superstructures is dependent on the
For prestressed concrete sections, Ig extent of cracking and effect of the
shall be used. cracking on the element’s stiffness.
3.4.4 Effective Torsional Moment of C3.4.4

Inertia The torsional stiffness of concrete
The effective torsional moment of members can be greatly reduced after the
inertia, Jeff for SCMs shall be determined onset of cracking.
as:
Jeff = 0.2Jg (3.4.4-1)
where:
Jg = gross torsional moment of inertia
The torsional moment of inertia for
superstructures shall not be reduced.
3.5 GLOBAL DISPLACEMENT CRITERIA

Each frame or bent shall satisfy: Figure 3.5.1-1 strictly represents the
case where the bridge is assumed to have
• Ordinary Standard Bridge
two principal directions defined by the
ΔC ≥ ΔD (3.5.1-1) direction along the chord connecting the
ends of the frame and the direction
• Recovery Standard Bridge perpendicular to it, as in Equivalent Static
Analysis (ESA) where a curved bridge is
ΔC ≥ 1.4ΔD (3.5.1-2)
straightened out.
where: A hinge that exceeds the ultimate
curvature capacity, ϕu is vulnerable to
ΔC = frame or bent displacement shear failure and a consequent loss of
capacity in the local axial capacity. It should be noted that as
principal/critical axis of member a structure develops plastic hinges, the
ΔD = frame or bent displacement displacement when the first hinge
demand in the local reaches ϕu defines Δc, even if that hinge
principal/critical axis of member was not the first to form.
ΔD and ΔC shall be measured in the
same local principal/critical axis.
Figure 3.5.1-1 Global Force Deflection Relationship

ΔD shall be obtained by performing The factor of 1.4 in the displacement

analyses as specified in Section 4.2. ΔD criterion of Equation 3.5.1-2 is intended to
shall correspond to the maximum ensure that Recovery bridges perform as
displacement as shown in Figure 3.5.1-1. specified in Section 1.3 even when
ΔC shall be obtained by performing subjected to seismic hazard levels greater
analysis as specified in Section 5.2.2. ΔC than the design seismic hazards. The
shall correspond to the lateral capacity of factor was obtained by analyzing a
the bridge or bent when any plastic hinge sample of mostly single column bridges
reaches its ultimate curvature capacity, ϕu across Northern and Southern California
as shown in Figure 5.3.6.2-1. with fixed column bases for the 2475-year
Abutments and in-span hinges shall and 975-year return period design spectra
also satisfy Equations 3.5.1-1 and 3.5.1- and averaging the resulting ratios of the
2, where ΔC and ΔD shall be taken as: displacement demands produced by the
2475-year return period DS to that
ΔC = support length of the abutment or produced by the 975-year return period
in-span hinge as specified in DS (Yoon et al., 2018). Limited analyses
Section 6.3.3 and 7.2.3.2 on bridges supported on deep
ΔD = frame/bridge displacement demand foundations indicate that the factor of 1.4
in the longitudinal direction may result in a conservative design for
measured at the abutment or in- bridges on deep foundations relative to
span hinge. those on shallow foundations. An
adjustment to the factor of 1.4 may be
The analytical model for determining warranted when the analysis results of a
the displacement demands and capacity more comprehensive bridge database
shall include the contribution of become available.
foundation flexibility, Δf as shown in The displacement capacity, ΔC is
Figures 3.5.1-2 and 3.5.1-3 and the measured when all plastic hinges within
flexibility of capacity protected members, the structure have formed and any one of
Δb , as shown in Figure 3.5.1-3. In Figure the plastic hinges reaches its ultimate
3.5.1-2, Δp* equals portion of the plastic curvature capacity.
displacement capacity which, when
col
added to ΔY and Δf , equals the
displacement demand.

Figure 3.5.1-2 Effects of Foundation Flexibility on the Force-Displacement Curve of

a Single Column Bent
Figure 3.5.1-3 Effects of Bent Cap and Foundation Flexibility on Force-Deflection

Curve of Bent
3.5.2 Local Principal/Critical Axes

The local principal/critical axes for a
frame or bent shall be taken as:
For Equivalent Static Analysis (ESA):

(a) the direction along a chord
connecting the ends of the frame
(b) the direction perpendicular to the
chord defined in (a)
For Elastic Dynamic Analysis (EDA):

(a) the direction along a chord
connecting the ends of the frame
(b) the direction along the centerline of
a bent
(c) the direction perpendicular to the
centerline of the bent defined in (b)
For Nonlinear Time History Analysis

(NTHA):
(a) the direction along the centerline of
a bent
(b) the direction perpendicular to the
centerline of the bent defined in (a)
3.6 LOAD AND RESISTANCE FACTORS

For all seismic-related calculations,
the following factors shall be used:
• resistance factor for flexure, ϕ = 1.0
• resistance factor for shear, ϕ = 1.0
• load factor for Dead Load = 1.0
• load factor for Live load = 0


SECTION 4: SEISMIC DEFORMATION DEMANDS AND ANALYSIS METHODS 4-1
SECTION 4
Seismic Deformation Demands and Analysis Methods
4.1 GENERAL C4.1

Seismic deformation demands shall Seismic deformation demands are
be determined using the methods characterized by the displacements,
specified in the following sections. rotations, curvatures, or strain
experienced by the structure.
Displacement ductility and curvature
ductility are the most frequently used
measures of inelastic response (Priestley
et al., 1996). The former relates to overall
structural response while the latter relates
to the response of an individual section.
4.2 ANALYSIS METHODS C4.2

Equivalent Static Analysis (ESA), The equal displacement
Elastic Dynamic Analysis (EDA), or approximation (Veletsos and Newmark,
Nonlinear Time History Analysis (NTHA) 1960) assumes that the maximum
shall be used to determine displacement displacement resulting from the inelastic
demands, as specified in Table 4.2-1. response of a structure is approximately
Equal displacement approximation of equal to the displacement obtained from
structural response shall apply to ESA an analysis using the linear elastic
and EDA. response spectrum, as shown in Figure
When NTHA method is used, the C4.2-1.
designer shall also perform an ESA of the The threshold for applicability of the
same bridge as a rough check on the equal displacement approximation is
analysis results. The results obtained by taken conservatively by Caltrans as an
NTHA shall supersede those obtained by initial period greater than or equal to 0.7
ESA provided the reduction in seconds.
displacement demands are within 50% of Forces and moments resulting from
the ESA values. linear-elastic analyses (i.e., ESA and
EDA) are unrealistic and should not be
used for design. Only the displacement
estimates are useable.

Nonlinear Time History Analysis is

included for routine bridge design in the
current version of the SDC as the method
can, in general, be used to analyze any
bridge. However, to guard against the use
of improper NTHA models and ensure
that analyses results are credible, NTHA
results are checked against those
obtained by the simplified, although
approximate ESA. If the displacement
demand obtained by NTHA is less than
50% of those obtained by ESA, the NTHA
result may be used if the designer
provides a justification acceptable to the
Office Chief of OEEAR.
Table 4.2-1 Applicability of Methods for Displacement Demand Analysis
ANALYSIS METHOD
PARAMETER
ESA EDA NTHA
Maximum bridge length 1000 ft 3000 ft *1 No restriction
Maximum skew angle 30° No restriction No restriction
Maximum bearing
difference between 5° 20° No restriction
supports
*1 The maximum bridge length requirement shall not apply when EDA is used for viaducts
with repeating frame systems and geometry.

Figure C4.2-1 Equal Displacement Approximation
4.2.1 Equivalent Static Analysis C4.2.1

Equivalent Static Analysis (ESA) may In ESA, the seismic excitation is
be used to determine displacement assumed to be an equivalent static
demands where the structural response horizontal force applied to individual
can be idealized by a single mode, frames. The horizontal force is applied at
subject to the limitations specified in the vertical center of mass of the
Table 4.2-1. superstructure and distributed
The displacement demand, ΔD shall horizontally in proportion to the mass
be determined as: distribution. The lateral force-
displacement curve is obtained from a
W Sa pushover analysis of the bridge.
ΔD = (4.2.1-1)
K The period, T of a bent or frame is
calculated as:
where:
Sa = design spectral acceleration T = 2π� W ⁄ gK (C4.2.1-1)
coefficient at the structure period
W = tributary weight of the structure where:
K = effective stiffness of the bent or
g = acceleration due to gravity
frame

The effective stiffness shall be taken For straight non-skewed bridges, the
as the slope of the line passing through displacements obtained using ESA are
the origin and the point representing generally close to those obtained using
formation of the first structural plastic EDA or NTHA. However, for horizontally
hinge on the force - displacement curve. curved or skewed bridges, the 2-D
The design spectrum shall be applied displacements obtained by ESA are
along the principal directions of the generally more conservative than the 3-D
bridge. The resulting displacement displacements obtained by EDA and
demands need not be combined. NTHA.
For the special case of single span Effective abutment longitudinal
bridges, the displacement demand in the stiffness, Keff is determined as specified in
longitudinal direction shall be determined Section 6.3.1, including the effectiveness
as follows: assessment using abutment
(a) Use the tributary weight of the displacement coefficient, Ra .
superstructure, W and the effective Determination of displacement
abutment longitudinal stiffness, Keff demand in the transverse direction of
to determine the structure period, T single span bridges is not required as the
using Equation C4.2.1-1 bridge translation in that direction is
(b) With the period, determine the limited upon failure of the shear key.
spectral acceleration, Sa from the
Design Spectrum
(c) Determine the displacement
demand from Equation 4.2.1-1
4.2.2 Elastic Dynamic Analysis C4.2.2

For EDA, the design spectrum shall be The response of multi-frame bridges is
used to perform a linear elastic multi- complicated by the interaction of frames
modal spectral analysis. The number of that vibrate with different frequencies and
modes considered in the analysis shall be mode shapes. Models (a) and (b)
sufficient to capture at least 90% mass represent situations where the joints open
participation in each of the longitudinal and close, respectively, bounding the
and transverse directions. A minimum of bridge response. Depending on software
three elements per column and four capabilities, model (a) could be one of
elements per span shall be used for several stand-alone frame models, or a
developing the analytic model. global model made discontinuous by the
use of releases between frames.

For multi-frame bridges, two dynamic

analyses, shall be performed to capture
the upper bound of the assumed
nonlinear response of the bridge, as
follows:
(a) an individual frame model with no
abutment participation (i.e., a
discrete tension model)
(b) a continuous global model with all
frames locked together (i.e., a
global compression model).
Abutment stiffness shall be
included in the global compression
model, as specified in Section
4.3.1.
The design spectrum shall be applied The CQC3 method (Menun and Der
simultaneously in two directions along a Kiureghian, 1998) does not require
set of orthogonal axes. The total response rotations of the design spectrum or
shall be determined by using either of the structure axes in order to produce the
following methods: maximum response as it uses a formula
• Complete Quadratic Combination to determine the critical orientation of the
3 (CQC3) design spectrum that produces the
• Square Root of Sum of Squares maximum response. Refer to MTD 20-17
(SRSS) for additional information on Elastic
Dynamic Analysis.
For the SRSS method, the design Generally, realistic results are
spectrum shall be rotated to determine obtained if the analysis tool is capable of
the total response. A minimum of four producing displacement results along the
rotations at 30° intervals shall be used. principal axes of each member. If
displacements in the local transverse (ΔT )
and longitudinal (ΔL ) directions are not
directly available from the analysis tool,
they may be approximated from the global
X and Y displacements as follows (see
Figure C4.2.2-1):
ΔL = |ΔX cos θ|+|ΔY sin θ| (C4.2.2-1)
ΔT = |ΔX sin θ|+|ΔY cos θ| (C4.2.2-2)
where:
θ = angular difference between the
local and global directions (see
Figure C4.2.2-1)

T = Local transverse direction Y = Global transverse direction

L = Local longitudinal direction X = Global longitudinal direction
Figure C4.2.2-1 Local and Global Coordinate Systems
4.2.3 Nonlinear Time History Analysis C4.2.3

Nonlinear Time History Analysis Nonlinear Time History Analysis
(NTHA) shall model soil-foundation- (NTHA) is the most comprehensive
structure interaction, gaps and impact on method for capturing the seismic
gap closure, multiple support excitations, demands of bridge members. However, it
isolation/damper devices, and nonlinear requires more resources than ESA and
soil, material, and hysteretic behavior. EDA when all three analysis methods are
General damping of bridge applicable. If geometric non-linearity is
components shall be modeled using an included in the NTHA model, the P-Δ
average Rayleigh damping ratio of 3% requirement of Section 4.4.4 need not be
specified at two periods, namely (a) the checked.
fundamental period, and (b) the period Unlike the ESA and EDA methods,
corresponding to attainment of 80% mass NTHA is capable of capturing the effects
modal participation. of nonlinear behavior such as yielding of
The input ground motions shall be structural components, soil-foundation-
applied at the bridge supports and shall structure interaction, opening and closing
consist of at least seven acceleration or of expansion joints, geometric
displacement time histories based on the nonlinearity, and nonlinear behavior of
fault type, earthquake intensity, fault restrainers and abutments.
proximity, and geology of the area.

All ground motions shall be matched Methods of developing seismic ground

to the site’s design spectrum using the motions for time history analysis include:
time domain method. (a) Using synthetic motions based on
Each set of ground motions shall be site characteristics
rotated in 45° increments for at least a (b) Creating idealized motions by
total of three angular directions (i.e., 0°, matching existing records to a
45°, and 90°) to maximize the structural target acceleration response
response. spectrum
For ground motions representing (c) Using seed records from the Next
near-fault scenarios and fault crossing Generation Attenuation (NGA)
where the orientation of the motions has database and site conditions to
been specified by the geo-professional, create site-specific motions.
the motions shall not be rotated or
spectrum-matched.
4.3 STRUCTURAL MODELING
4.3.1 Global Models C4.3.1

Except as provided in Section 4.3.2, a
“global” (or “structural system”) model of
the bridge shall be used to capture the
displacement demand of the entire bridge
system when EDA or NTHA is used. This
analytical model shall include the effects
of adjacent components, subsystems,
and boundary conditions.
For bridges longer than 3000 feet, For NTHA, the entire soil-foundation
multiple partial models of the bridge shall system shall be modeled explicitly with
be permitted. soil springs attached to the structural
Each partial model shall include a foundation elements, as illustrated in
boundary frame or an abutment beyond Figure 6.2.4.2-2. The entire force-
each end of the frame under deflection curve of the soil shall be used
consideration, as shown in Figure 4.3.1-1. in the model.
A global model shall include soil-
foundation-structure interaction to
determine the maximum displacement
demand.
For NTHA, the entire soil-foundation
system shall be modeled explicitly with
soil springs attached to the structural
foundation elements, as illustrated in
Figure 6.2.4.2-2. The entire force-
deflection curve of the soil shall be used
in the model.
Tran. 1 Boundary Frame 1

Boundary Frame 2 Abut
Tran. 2
Long. 2
Abut
Long. 3
Long. 1
Tran. 3
Model 1 Boundary Frame 3
Boundary Frame 2
Model 2
Legend
Model 3
Long.: Longitudinal Axis
Tran.: Transverse Axis
Bridge Expansion Joint
Figure 4.3.1-1 Multi-Frame Modeling Techniques
For ESA and EDA, the entire soil-

foundation system shall be modeled
either:
(a) explicitly as described above for
NTHA but with the initial slope of
the force-deflection curve used for
the soil stiffness, or
(b) by use of an equivalent 3-D
stiffness matrix. An equivalent 3-D
stiffness matrix shall be
determined from the nonlinear
static pushover analysis of the soil-
foundation system that uses the
explicit soil-structure foundation
model. The equivalent stiffness
shall be the idealized initial
stiffness of the force-deflection
curve of the pushover analysis.

Abutment stiffness shall be included in Information on abutment longitudinal

the global model as follows: modeling is provided in Section 6.3.1.
EDA and ESA Methods

• For bridges with three or less
number of frames, one-half the
abutment longitudinal stiffness
shall be used at each abutment.
• For bridges with four or more
number of frames, abutment
longitudinal stiffness shall be
ignored.
• Abutment transverse stiffness shall
be as specified in Section 6.3.2.
NTHA Method The shear key is usually designed to

• Abutment longitudinal stiffness fail under the design seismic hazards
represented by a bilinear or (DSH) unless it is specifically designed to
nonlinear model, contact/gap sustain DSH level loading. After the shear
elements, and other nonlinear key fails, the lateral resistance is provided
elements shall be modeled in the by the friction between the superstructure
analysis, regardless of the number and abutment, and the coefficient of
of frames. friction is assumed to be 0.3. The initial
• Abutment transverse stiffness shall slope is based on an assumed 2-inch gap
be estimated using the shear key typically present between the
stiffness, as shown in Figure 4.3.1- superstructure and the shear key.
2
sup
In Figure 4.3.1-2, Pdl is the
superstructure axial load resultant at the
abutment.
Figure 4.3.1-2 Abutment Transverse stiffness for Nonlinear Time History Analysis
4.3.2 Stand-Alone Models C4.3.2

A stand-alone or discrete frame model In situations where the software
may be used to determine the upper required for the analysis of a multi-frame
bound to the displacement demand. bridge is unavailable or inadequate to
Each frame shall satisfy all applicable analyze multi frame bridges, the bridge
SDC requirements. may be analyzed by performing stand-
alone analysis on the individual frames.
4.3.2.1 Transverse Stand-Alone Models

Transverse stand-alone frame models
shall assume lumped mass at the top of
bents or columns. Hinge spans shall be
modeled as rigid elements with half of
their mass lumped at the adjacent column
as shown in Figure 4.3.2.1-1. The
transverse analysis of end frames shall
include an estimate of the abutment
stiffness as specified in Section 6.3.2. The
transverse displacement demand at each
bent in a frame shall include the effects of
rigid body rotation around the frame’s
center of rigidity.
4.3.2.2 Longitudinal Stand-Alone Models

Longitudinal stand-alone frame
models shall include the short side of
hinges with a concentrated dead load,
and the entire long side of hinges
supported by rollers at their ends as
shown in Figure 4.3.2.2-1.
Abutment longitudinal stiffness shall
be included as specified in Section 4.3.1.

Lumped mass, typ.

Abut Bent Bent Bent Bent
1 2 3 4 5
A In-span hinge
A
0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
Lumped mass at Bent 2
PLAN VIEW
Lumped
Stiffness
Section A – A
Figure 4.3.2.1-1 Transverse Stand-Alone Model

Note:
The abutment longitudinal stiffness is taken as zero when ESA and EDA methods of analysis are
used for bridges with four or more frames.
Figure 4.3.2.2-1 Longitudinal Stand-Alone Model

4.4 DEFORMATION DEMANDS
4.4.1 Displacement Ductility Demand C4.4.1

Displacement ductility demand, μD The maximum displacement ductility
shall be used to measure the ductility of a demand values in Table 4.4.1-1 are
SCM. μD shall be defined as: based on laboratory testing of mostly
single bridge columns, fixed at the base
ΔD
μD = (4.4.1-1) (Lehman and Moehle, 2000; Schoettler et
ΔY (i) al., 2015). Adjustments for multi-column
where: bents and bridges affected by soil-
foundation-structure interaction reflect the
ΔD = frame or bent displacement complexity of these systems.
demand in the local The closer the μD value is to the
principal/critical axes of a member maximum limit specified in Table 4.4.1-1,
ΔY (i) = frame or bent displacement at the more economical the design, and vice
the instant a plastic hinge forms in versa.
the i-th SCM For pile groups with a pinned pile-to-
The displacement ductility demand cap connection in Class S2 soil, μD is
values, for SCMs shall not exceed the
limited to 1.0 because plastic hinging is
values specified in Table 4.4.1-1.
not allowed in the piles.
For pile groups in Class S2 soil, plastic
Seismic critical members with flexible
hinging shall not be permitted in the piles
foundations will have low displacement
except at the top of piles if the pile-to-cap
ductility demands because of larger ΔY .
connection is fixed.
The minimum flexural strength
requirement of Section 5.3.6.1 or the P-Δ
requirements of Section 4.4.4 may govern
the design of frames where foundation
flexibility increases the period of the
structure and lowers the design spectral
acceleration.
It is recognized that as the framing
system becomes more complex and
boundary conditions are included in the
demand model, an increased percentage
of the calculated global displacement is
significantly affected by the flexibility of
components other than the SCMs within
the frame. For such systems, including
Type I shafts, global ductility demand
values are usually well below the
maximum values specified in Table 4.4.1-
1. The value of μD for such members may
not exceed 3.5.

Table 4.4.1-1 Displacement Ductility Demand Values, μD
Limiting Displacement Ductility

Demand
Plastic
Hinge Seismic Critical Member Recovery Standard
Location Ordinary Bridge
Standard
Bridge
SEE FEE
Substructure Column in a single-column bent 4.0 2.5 1.5

supported on a footing or Type II
shaft
Column in a multi-column bent 5.0 3.5 2.0

supported on a footing or Type II
shaft
Pile extensions or Type I shaft, plastic 5.0 3.5 2.0

hinge at cap/superstructure soffit
Foundation Pile extensions or Type I shaft, plastic 3.5 2.5 1.5

hinge below ground
Pile groups in Class S2 soil, fixed pile 2.5 1.5 1.0

to cap connection, plastic hinge on
top of pile
Pile groups in Class S2 soil, pinned 1.0 1.0 1.0

pile to cap connection
Pile groups in Class S1 soil * * *
* Lateral analysis not required for foundations in Class S1 soil. See Section C6.2.3.1.
4.4.2 Overstrength Demand

Capacity protected members shall be
designed to resist the overstrength
demands imparted by SCMs and
sacrificial elements.

4.4.2.1 Overstrength Moment Demand C4.4.2.1

The overstrength moment of a SCM, The use of overstrength moments of
Mocol shall be taken as: SCMs to design capacity-protected
members is intended to ensure that fusing
Mocol = 1.2 Mpcol (4.4.2.1-1) occurs in the SCM as well as to account
for:
where: • Unexpected material strength
variations between the SCM and
Mpcol = idealized plastic moment capacity adjacent members
of a SCM • Actual moment capacities greater
than the idealized plastic moment
capacity.
4.4.2.2 Overstrength Shear Demand C4.4.2.2

The shear demand transferred to The shear force associated with the
adjacent capacity protected members by overstrength moment, Vo
col
may be
col
SCMs shall be the shear force, Vo determined from:
associated with the overstrength moment,
col col col
Mo . All potential plastic hinge locations Vo = 1.2Vp (C4.4.2.2-1)
shall be considered to determine the
maximum possible shear demand. where:
col
Vp = plastic shear corresponding to the
idealized plastic moment capacity
of a SCM
4.4.3 Superstructure and Bent Cap

Seismic Demand
4.4.3.1 Seismic Moment Demand C4.4.3.1
The superstructure and bent cap The overstrength force demand in the
moment demands on the right and left superstructure corresponds to the
sides of the superstructure-to-column maximum force demand in the
R
joint along the longitudinal direction, MD earthquake resisting system. When the
and MDL , respectively, shall be taken as maximum force demand is reached
(see Figure 4.4.3.1-1): during a seismic event, the following
additional forces are present: dead loads,
R R R
MD = Mdl + Mp/s + Meq
R
(4.4.3.1-1) secondary forces from post-tensioning
(i.e., secondary prestress effects).
L L L L
MD = Mdl + Mp/s + Meq (4.4.3.1-2)

Figure 4.4.3.1-1 Superstructure Demand Generated by Column Overstrength Moment
where: Several analysis techniques may be

used to distribute the column earthquake
MD , MDL = moment demands on the
R
moment and shear demands to the
right and left sides of superstructure. If a moment distribution or
superstructure-to-column joint, a frame analysis method is used, the
respectively superstructure can be modeled as a
R L
Mdl , Mdl = dead load plus added dead continuous beam. A moment of
load moments on the right and left magnitude equal to Meq
col-top
+
sides of superstructure-to-column col-top
joint, respectively �Veq × Dc.g � associated with each
R L column can be applied at each
Mp/s , Mp/s = effective secondary
superstructure/column joint and then
prestress moments (after losses distributed to obtain the moments and
have occurred) on the right and left shears in the superstructure.
sides of superstructure-to-column Due to the uncertainty in the
joint, respectively
R L
magnitude and redistribution of
Meq , Meq = earthquake moments on the secondary prestress moments and
right and left sides of shears (Mp/s and Vp/s ) at the extreme
superstructure-to-column joint seismic limit state, these forces should be
col-top
induced by Meq and included in the superstructure when the
(Veq
col-top
× Dc.g) overall demand is increased, and
Dc.g = distance from the top of column to disregarded when the overall demand is
decreased.
the center of gravity of the
superstructure/bent cap

The seismic moment on the top of

col-top
column, Meq shall be determined as:
col-top col-top col-top col-top

Meq = Mo - Mdl - Mp/s
(4.4.3.1-3)
where:
col-top
Mo = column overstrength moment
on the top of column
col-top
Mdl = dead load plus added dead
load moments on the top of column
col-top
Mp/s = effective secondary prestress
moment on the top of column
col-top
The seismic moment, Meq shall be
distributed into the superstructure
considering longitudinal bridge movement
to the right and to the left.
Effective superstructure width as
defined in Section 7.2.1.1 shall be used in
computing the seismic demand
distributed to the superstructure.
4.4.3.2 Seismic Shear Demand

The superstructure and bent cap
shear demands on the right and left sides
R
of the superstructure-to-column joint, VD
L
and VD , respectively, shall be determined
as:
R R R R
VD = Vdl + Vps + Veq (4.4.3.2-1)
L L L L
VD = Vdl + Vps + Veq (4.4.3.2-2)
where:
VD , VDL = shear demands on the right

R
and left sides of superstructure-to-

column joint, respectively
Vdl , VdlL = dead load plus added dead
R
load shears on the right and left

sides of superstructure-to-column
joint, respectively
R L
Vp/s , Vp/s = effective secondary
prestress shears (after losses have
occurred) on the right and left sides
of superstructure-to-column joint,
respectively
R L
Veq , Veq = seismic shears on the right
and left sides of superstructure-to-
col-top
column joint induced by Meq
col-top
and Veq earthquake
The seismic shear on the top of

col-top
column, Veq shall be determined as:
col-top col-top col-top col-top

Veq = Vo - Vdl - Vp/s
(4.4.3.2-3)
where:
col-top
Vo = overstrength shear on the top
of column
col-top
Vdl = dead load plus added dead
load shear on the top of column
col-top
Vp/s = effective secondary prestress
shear on the top of column
4.4.4 P-Δ Effects C4.4.4

The effects of gravity loads acting P-Δ effects can only be accurately
through lateral displacements shall be captured with nonlinear time history
included in the design. analysis. In lieu of such analysis,
For SCMs meeting the ductility Equation 4.4.4-1 is used to establish a
demand limits specified in Section 4.4.1, conservative limit for lateral
P-Δ effects may be ignored if Equation displacements induced by axial load.
4.4.4-1 is satisfied. The moment demand at the point of
maximum moment in the shaft is shown in
Figure 4.4.4-1. As the displacement of the
top of column is increased, moment
demand values at the base pass through
My, Mn, Mp, and Mu (key values defining
the moment-curvature curve, see Figure
4.4.4-1). The idealized plastic moment Mp
is always less than Mu in a well-confined
column.

col
Pdl Δr ≤ 0.25Mp (4.4.4-1)
where:
Pdl = axial load attributed to dead load
Δr = relative lateral offset between the
point of contra-flexure and the
base of the plastic hinge, as shown
in Figure 4.4.4-1. For Type I shafts:
Δr = ΔD − Δs (4.4.4-2)
Δs = shaft displacement at the point of

maximum moment
Figure 4.4.4-1 P-Δ Effects on Bridge Columns


SECTION 5: SEISMIC DEFORMATION CAPACITIES 5-1
SECTION 5
SEISMIC DEFORMATION CAPACITIES
5.1 GENERAL
Deformation capacities of bridge
members, frames, and bents shall be
determined as specified in the following
sections.
5.2 GLOBAL DISPLACEMENT CAPACITY

5.2.1 General
Global displacement capacity, ΔC
shall be determined along the directions
specified in section 3.5.2.
5.2.2 Inelastic Static Analysis C5.2.2

Except as provided herein, Inelastic Inelastic Static Analysis is commonly
Static Analysis (ISA) shall be used to referred to as “pushover” analysis. ISA is
determine the displacement capacity, ΔC a piecewise linear analysis of a bridge
of a frame or bent, provided the seismic frame or bent as successive plastic
response of the structure is dominated by hinges form in the earthquake resisting
a single translational mode of vibration. system. ISA captures the overall
ΔC shall correspond to the lateral capacity nonlinear behavior of the earthquake
of the bridge or bent when any plastic resisting system by applying a lateral
hinge reaches its ultimate curvature static load at the center of gravity of the
capacity, ϕu . ISA shall be performed with superstructure or the bent, and
the dead load applied while a lateral static monotonically increasing the load until the
load or displacement is applied at the displacement capacity criterion specified
center of gravity of the superstructure or in Section C3.5.1 is reached. Because the
the bent cap. Nonlinear soil-foundation- analytical model accounts for the
structure interaction shall be taken into redistribution of internal forces as plastic
account by means of soil springs. hinges form, ISA provides a more realistic
Abutment stiffness shall be included, as seismic response of the bridge than
specified in Sections 6.3.1 and 6.3.2. elastic analysis.
For bridges where Equivalent Static Traditionally, Caltrans has used ISA to
Analysis (ESA) may be used to determine determine displacement capacity and
displacement demand as specified in ESA to determine displacement demand.
Sections 4.2 and 4.2.1, “Local
Displacement Capacity” equations may
be used as the ISA.

For the special case of single span Local Displacement Capacity

bridges, the displacement capacity shall
Local displacement capacity, Δc is
be greater than or equal to the larger of
defined as a member’s displacement
the minimum support length of the
capacity attributed to its elastic flexibility,
abutment as specified in Section 6.3.3 col
and the displacement demand as ΔY and its plastic hinge deformation
specified in Section 4.2.1. capacity, Δp .
The local displacement capacity of a
member is based on its rotation capacity,
which in turn is based on the curvature
capacity of its plastic hinges. Δc is
independent of the effects of adjacent
members and subsystems.
Fixed-Free and Fixed-fixed SCMs are
idealized as one and two cantilever
segments, as shown in Figures C5.2.2-1
and C5.2.2-2. Δc is determined from:
col
Δc = ΔY + Δp (C5.2.2-1)
1
ΔY = 3 L 2 ϕ Y
col
(C5.2.2-2)
1
Δp = θp �L − 2
Lp � (C5.2.2-3)
θp = Lp ϕp (C5.2.2-4)
ϕp = ϕu − ϕY (C5.2.2-5)
where:
L = distance from the point of
maximum moment to the point of
contra-flexure (in.)
Lp = equivalent plastic hinge length (in.)
Δp = idealized plastic displacement
capacity due to rotation of the
plastic hinge (in.)
col
ΔY = idealized yield displacement at the
formation of the plastic hinge (in.)
ϕp = idealized plastic curvature capacity
(assumed constant over Lp )
(rad/in)

Figure C5.2.2-1 Local Displacement Capacity of a Typical Cantilever Column with

Fixed Base
Figure C5.2.2-2 Local Displacement Capacity of a Typical Fixed-Fixed Column

ϕu = curvature capacity when the

concrete strain reaches εcu or the
longitudinal reinforcing steel
reaches the reduced ultimate
R
strain εsu (rad/in)
ϕY = idealized yield curvature defined
by an elastic-perfectly-plastic M-ϕ
curve of the cross section (rad/in)
θp = plastic hinge rotation capacity
(radian)
For Type I shafts, Equation C5.2.2-3

becomes:
Δp = θp L (C5.5.2-6)
where:
L is the portion of the shaft length
measured from the center of the plastic
hinge to the center of gravity of the
superstructure. For fixed-fixed column,
the dimensions L1 and L2 in Figure
C5.2.2-2 should be substituted for L in
Equations C5.2.2-2 and C5.2.2-3.
Traditionally, the local displacement

ductility capacity of a SCM, has been
defined as:
Δc
μc = col (C5.5.2-7)
ΔY
Local displacement ductility capacity

is based on an equivalent member that
approximates a fixed base cantilever
element as shown in Figure C5.2.2-3.

Figure C5.2.2-3 Local Ductility Assessment

Figure C5.2.2-3 Local Ductility Assessment (continued)

5.3 SEISMIC CRITICAL MEMBERS

Columns, Type I shafts, Pile/Shaft A non-seismic critical member may be
groups in Class S2 soils, and pile- designed as a seismic critical member in
extensions shall be classified as seismic order to meet a nonstandard design
critical members (SCMs). Any member requirement. For example, if capacity
intended to function as a SCM as protected members such as outrigger
specified in Section 1.4 but not listed bent cap beams and “C” bent cap beams
above shall require a PSDC. are expected to experience a moderate or
Expected locations of plastic hinges in significant damage, they should be
SCMs shall be designed and detailed for designed and detailed as SCMs.
ductile response. Ductile design and detailing of SCMs
The requirement of ductile response also applies in areas of low seismicity
shall apply to SCMs regardless of the where the bridge response might be in the
seismicity level of the bridge site. essentially elastic range.
5.3.2 Plastic Hinge Region C5.3.2

The plastic hinge region, Lpr shall be The plastic hinge region, Lpr is the region
taken as the larger of: of the SCM that is expected to form a
• 1.5 times the cross-sectional plastic hinge. Plastic hinge regions
dimension in the direction of require enhanced lateral confinement.
bending
• The region of a SCM where the
moment exceeds 75% of the
col
maximum plastic moment, Mp
• 0.25 (Length of SCM from the point
of maximum moment to the point of
contra-flexure)
5.3.3 Axial Load Limits C5.3.3

The axial load ratio for SCMs in The analytical models describing the
compression shall satisfy: ductile response of SCMs have been
calibrated by many column tests generally
Pdl
ρdl = f' ≤ 0.15 (5.3.3-1) using a 10% axial load ratio. Although
c Ag
tests with axial loads up to 0.35f'c Ag
and (Benzoni et al., 1996) have shown that the
ductility capacity of confined columns will
Pc diminish with increasing axial loads, there
ρc = f' ≤ 0.22 (5.3.3-2)
c Ag are not enough data points to reliably
establish the column ductile behavior
where: under axial loads greater than 0.15f'c Ag . It
is expected that future research will
extend the knowledge base beyond 0.15
f'c Ag and to SCMs other than columns.
Ag = gross cross section area of a SCM In transverse frame analysis, axial

ρdl = axial load ratio due to dead load forces in multi-SCM bents can vary from
ρc = axial load ratio due to dead load the dead load state when subjected to
and overturning seismic overturning forces due to framing
Pdl = axial force due to dead load action of the cap beam. Overturning
effects are negligible in longitudinal frame
Pc = axial force due to dead load and
analysis and may be disregarded.
overturning
The value of f'c for use in determining
the axial load limits specified above shall
not exceed 5000 psi.
5.3.4 Equivalent Plastic Hinge Length C5.3.4

The equivalent plastic hinge length, Lp The equivalent plastic hinge length, Lp
shall be taken as: is the length of a SCM over which the
plastic curvature is assumed constant for
Case (A)
estimating plastic rotation.
• Plastic hinge at ends of columns
supported on footings or Type II
shafts
• Plastic hinge at the boundaries of
steel pipe in columns/shafts with
steel pipes (casing or CISS)
Lp = 0.08L + 0.15fye dbl ≥ 0.3fye dbl

(5.3.4-1)
where:
fye = expected yield strength for ASTM
A706 reinforcement (ksi)
dbl = nominal bar diameter of
longitudinal column reinforcement
(in.)
L = length of a SCM from the point of
maximum moment to the point of
contraflexure (in.)
Case (B)
• Plastic hinge at the top of
horizontally-isolated flared
columns
• Plastic hinge at ends of steel-
jacketed columns
Lp = G + 0.3fye dbl (5.3.4-2)
where:

G = gap between the isolated flare and

soffit of the bent cap, or the gap
between the steel jacket and soffit
of the bent cap or top of the footing
(in.)
In Equation 5.3.4-2, fye and dbl have

the units of ksi and inches, respectively.
For columns flared only in one
direction, Equation 5.3.4-1 shall be used
for the “non-flared” direction.
Case (C)
• Plastic hinge in Type I shafts
• Plastic hinge occurring at least a
distance, Dc away from boundaries
of steel pipe in columns/shafts with
steel pipes (casing or CISS)
Lp = D* + 0.08Ho-max (5.3.4-3)
where:
D* = diameter for circular shaft or the
least cross section dimension for
oblong shafts
Ho-max = length of shaft/column from
point of maximum moment to point
of contraflexure above ground
considering the plastic hinge at the
point of maximum moment.
When vertical flare isolation is used in
combination with horizontally isolated
flare, the equivalent plastic hinge length
shall be taken as the lesser of Lp
calculated using Equations 5.3.4-1 and
5.3.4-2, where G shall be taken as the
length from the bent cap soffit to the
bottom of the vertical flare isolation
region.

5.3.5 Confined Core C5.3.5

Seismic critical members shall be Single circular cores or multiple
detailed with either a single solid circular interlocking cores with hoop transverse
core or multiple solid interlocking cores. reinforcement provide confining pressure
to the core concrete and an inward
restraint against buckling of the
longitudinal bars (Priestley et al., 1996,
Mander et al., 1988b) and are used for
both circular and rectangular shaped
SCMs.
5.3.6 Flexural Capacity

5.3.6.1 Minimum Flexural Capacity
Each bent or frame shall have a
minimum plastic moment capacity (based
on expected material properties) to resist
a lateral force of ten percent of the
tributary weight of the bent or frame
applied as a static lateral load at the
center of gravity of the superstructure.
5.3.6.2 Moment-Curvature Analysis C5.3.6.2

The plastic moment capacity of all Moment curvature curve is derived
SCMs shall be determined by moment- from the curvatures associated with a
curvature (M-ϕ) analysis. The M-ϕ curve range of moments for a cross section
shall be idealized with an elastic perfectly based on the principles of strain
plastic response as shown in Figure compatibility and equilibrium of forces.
5.3.6.2-1. The elastic portion of the M-ϕ curves are used to represent
idealized curve shall pass through the material inelasticity either in concentrated
point marking the first reinforcing bar zero length plastic hinges or in distributed
yield. The idealized plastic moment plastic zones.
capacity shall be obtained by balancing
the areas between the actual and the
idealized M-ϕ curves beyond the first
reinforcing bar yield point, as shown in
Figure 5.3.6.2-1.

In Figure 5.3.6.2-1: Although ultimate displacements reported

in laboratory tests are traditionally based
Mne = nominal moment capacity
on the state when a 20 % reduction in the
based on expected material
maximum lateral resistance is attained
properties and a concrete strain of
(Park and Paulay, 1975; Priestley et al.
0.003
col 1996), the ultimate curvature reported by
Mp = idealized plastic moment Caltrans M-ϕ curve should not be reduced
capacity of a SCM by 20%. The M-ϕ analysis is based on
My = moment of a SCM corresponding Mander’s stress-strain model (Mander et
to the first reinforcing bar yield al., 1988a, 1988b) in which the ultimate
ϕy = yield curvature corresponding to compressive strain of concrete was
the first reinforcing bar yield defined as the strain corresponding to the
ϕY = idealized yield curvature first fracture of the confinement steel.
ϕu = ultimate curvature capacity Tests results (Saini and Saiidi, 2014)
have shown that ultimate displacements
For the transverse analysis of multi- based on main reinforcing bar fracture
column bents, additional column axial and damage to the core concrete are
force due to overturning effects shall be about 20% greater than those obtained
considered when determining the plastic using the theoretical Mander’s failure
moment capacity of the columns. criterion.
In transverse frame analysis, axial
forces in multi-SCM bents can vary from
the dead load state when subjected to
seismic overturning forces due to framing
action of the cap beam. Overturning
effects are negligible in longitudinal frame
analysis and may be disregarded.
Figure 5.3.6.2-1 Moment - Curvature Curve

5.3.7 Shear Capacity
5.3.7.1 General
The shear capacity of SCMs shall
satisfy:
col
ϕVn ≥ Vo (5.3.7.1-1)
Vn = Vc + Vs (5.3.7.1-2)
where:
ϕ = resistance factor for shear =1.0
Vn = nominal shear capacity (kip)
col
Vo = overstrength shear associated with
the overstrength moment of a
SCM, as specified in Section
4.4.2.2
Vc = nominal shear capacity provided
by concrete
Vs = nominal shear capacity provided
by shear reinforcement
5.3.7.2 Nominal Concrete Shear C5.3.7.2

Capacity
The nominal concrete shear capacity
for SCMs, Vc shall be taken as:
Vc = vc Ae (5.3.7.2-1)
where:
Ae = 0.8Ag (5.3.7.2-2)
• Inside the plastic hinge region
vc = (F1)(F2)�f 'c ≤ 4�f 'c (5.3.7.2-3)
• Outside the plastic hinge region
vc = 3(F2)�f 'c ≤ 4�f 'c (5.3.7.2-4)

0.3 ≤ F1 =
ρs fyh
+ 3.67 − μd ≤ 3 Figure C5.3.7.2-1 shows how the
0.15 value of F1 varies over a range of
(5.3.7.2-5) displacement ductility demand ratios, μd .
In Equation 5.3.7.2-5, the value of The volumetric ratio of transverse
“ρs fyh ” shall be limited to 0.35 ksi. reinforcement, ρs is defined in Section
5.3.8.2.
P
F2 = 1 + 2000A
c
< 1.5 (5.3.7.2-6)
g
For members with net axial load in

tension, vc = 0.
In Equations 5.3.7.2-3 to 5.3.7.2-6:
vc = permissible concrete shear stress
(psi)
f 'c = specified compressive strength of
unconfined concrete (psi)
fyh = specified minimum yield strength
of transverse reinforcement (ksi)
ρs = volumetric ratio of transverse
reinforcement
Pc = axial force on a SCM including the
effects of overturning (lb)
Ag = gross cross-sectional area of
SCM (in.2)
μd = local displacement ductility
demand = Δd ⁄ΔY (i)
Δd may be obtained by subtracting the

displacements due to foundation and bent
cap flexibilities from the global
displacement, Δd as illustrated in Figures
3.5.1-2 and 3.5.1-3. The global
displacement ductility demand, μD may be
used in in lieu of μd , provided a significant
portion of the global displacement is
attributed to the deformation of the SCM.

Displacement ductility demand, μd
Figure C5.3.7.2-1 Concrete Shear Factors
5.3.7.3 Nominal Shear Reinforcement

Capacity
The nominal shear reinforcement
capacity for confined circular or
interlocking core sections, VS shall be
taken as:
Av fyh D'
VS = (5.3.7.3-1)
s
where:
π
Av = n � 2 � Ab (5.3.7.3-2)
Av = area of shear reinforcement

perpendicular to the flexural
tension reinforcement (in.2)
n = number of individual interlocking
spirals or hoops in the core of the
sections

D’ = cross-sectional dimension of
confined concrete core measured
between the centerlines of the
peripheral hoop or spiral (in.)
s = spacing of shear reinforcement
(in.)
Ab = area of individual reinforcing steel
bar (in.2)
5.3.7.4 Maximum Shear Reinforcement

The nominal shear capacity provided
by the reinforcing steel, Vs shall satisfy:
Vs ≤ 8�f 'c Ae (5.3.7.4-1)
where, f 'c and Vs have the units of psi and

lb, respectively.
5.3.7.5 Minimum Shear Reinforcement

The area of shear reinforcement for
each individual core of SCMs confined by
hoops/spirals or interlocking
hoops/spirals shall satisfy:
D' s
Av ≥ 0.025 (5.3.7.5-1)
fyh
5.3.8 Transverse Reinforcement

Requirements
5.3.8.1 General C5.3.8.1
Transverse reinforcement shall be Sufficient amount of transverse
provided in SCMs to satisfy plastic shear reinforcement (i.e., confinement and
and curvature demands as specified in shear reinforcement) is provided in SCMs
Sections 5.3.7.1, 3.5.1, and 4.4.1. in order to meet plastic shear demands,
Transverse reinforcement shall be curvature demands resulting from
either ultimate butt-spliced hoops or imposed displacements, and to prevent
continuous spiral (where allowed) as buckling of the longitudinal compression
specified in Section 8.2.2.3. reinforcement (Mander et al., 1988a).
Combination of spiral reinforcement
with hoops shall not be used in a SCM.

In large diameter SCMs, hoops are

preferred over spirals because of the
larger bars and larger spacing used in
hoops to facilitate construction. The
discrete nature of hoops provides an
advantage in SCMs since the failure of
one hoop does not lead to a premature
plastic hinge failure. When a plastic hinge
forms, the confinement steel is exposed
as a result of loss of cover concrete. With
additional deformation, the strain in the
transverse reinforcement increases. Any
break at a single location in spiral
reinforcement may cause a considerable
length of the spiral to become ineffective
and lead to plastic hinge failure. Also, the
process of sampling and testing hoop
splices for QA/QC purposes is easier than
that of spiral splices.
Refer to Section 8.2.1 for types of
reinforcing bar splices.
5.3.8.2 Minimum Transverse C5.3.8.2

Reinforcement Inside the Plastic Hinge
Region
For Ordinary Standard bridges, the For SCMs with circular or interlocking
minimum transverse reinforcement in core sections, the transverse
terms of volumetric ratio, ρs, min provided reinforcement volumetric ratio, ρs is given
in the plastic hinge region shall be as by:
specified in Table 5.3.8.2-1. SCMs with
parameters outside those specified in 4 Ab
ρs = (C5.3.8.2-1)
Table 5.3.8.2-1 shall satisfy a minimum D' s
local displacement ductility capacity of
3.0. where:
For Recovery Standard bridges, ρs, min Ab = area of individual confinement
shall be taken as 0.01. steel bar (in.2)
D’ = cross-sectional dimension of
confined concrete core measured
between the centerlines of the
peripheral hoop or spiral (in.)
s = spacing of transverse
reinforcement measured along the
longitudinal axis of the SCM (in.)

Table 5.3.8.2-1 Minimum Transverse Reinforcement Volumetric Ratio (Ordinary

Standard Bridges)
Longitudinal Minimum
Diameter of Axial Load
Aspect Ratio, Reinforcement Transverse
SCM, Ratio,
L⁄Dc Ratio, Reinforcement,
Dc (ft.) ρdl (%)
ρl (%) ρs, min
≤8.0 3 ≤ Dc ≤6 ≤ 2.3 ≤10 0.006
10 < ρdl ≤ 15 0.007
6 < Dc ≤11 ≤ 2.15 ≤10 0.007
10 < ρdl ≤ 15 0.008
For the analysis of bridges with

rectangular-shaped SCMs having ties
and cross ties, ρs is given by:
Av
ρs = (C5.3.8.2-2)
D'c s
where:
Av = sum of area of the ties and cross
ties running in the direction
perpendicular to the axis of
bending (in.2)
D'c = confined column cross-section
dimension, measured out-to-out of
ties, in the direction parallel to the
axis of bending (in.).
The percent longitudinal

reinforcement ratio, ρl is given by:
ρl = (100Ast /Ag ) (C5.3.8.2-3)
The axial load ratio due to dead load,

ρdl is specified in Section 5.3.3.

A minimum volumetric ratio of

transverse reinforcement, ρs ensures
adequate confinement and dependable
rotational capacity in the plastic hinge
regions regardless of the displacement
demand imparted to the SCM.
In previous editions of the SDC, a
minimum local displacement ductility
capacity of 3.0 was specified. The
minimum volumetric ratios of transverse
reinforcement specified in Table 5.3.8.2-1
were calibrated (Unanwa and Mahan,
2018) to provide a minimum local
displacement ductility capacity equal to or
greater than 3.0. The minimum value of ρs
of 0.01 for Recovery Standard bridges is
intended to meet the enhanced
performance criteria for Recovery bridges
specified in Section 1.3, based on
previous bridge performance experience.
For SCMs with parameters outside
those specified in Table 5.3.8.2-1, a
minimum local displacement ductility
capacity of 3.0 may be difficult to achieve.
In such cases, an acceptable minimum
value of ρs may be established following
the PSDC procedure.
5.3.8.3 Transverse Reinforcement

Outside the Plastic Hinge Region
The volume of transverse
reinforcement required outside the plastic
hinge region, shall be greater than or
equal to 50% of the transverse
reinforcement provided within the plastic
hinge region.
5.3.8.4 Transverse Reinforcement for

Columns Supported on Type II Shafts
The volumetric ratio of transverse
reinforcement for columns supported on
Type II shafts shall satisfy the
requirements specified in Sections 5.3.8.2
and 5.3.8.3.

5.3.8.5 Transverse Reinforcement for

Type I Shafts with Larger Shaft
Reinforcement
Type I shafts designed with larger
longitudinal reinforcement below the
ground (i.e., shaft) than that used above
the ground (i.e., column) shall have a
volumetric ratio of transverse
reinforcement in the top 4Dc,max segment
of the shaft greater than or equal to 75 %
of the transverse reinforcement required
at the base of the column.
5.3.9 Longitudinal Reinforcement

Requirements
5.3.9.1 Maximum Longitudinal
Reinforcement
The maximum area of longitudinal
reinforcement in a SCM, Ast,min shall be
taken as:
Ast,min = 0.04Ag (5.3.9.1-1)
5.3.9.2 Minimum Longitudinal

Reinforcement
The minimum area of longitudinal
reinforcement in a SCM, Ast,min shall be
taken as:
Ast,min = 0.01Ag (5.3.9.2-1)
5.3.9.3 Minimum Size of Longitudinal

Reinforcement within Interlocking Hoops
The longitudinal bar size in the
interlocking portion of a SCM (i.e., “B”
bars in Figure 5.3.9.3-1) shall be chosen
to correspond to the longitudinal bar size
outside the interlocking portion (i.e., “A”
bars in Figure 5.3.9.3-1) as shown in
Table 5.3.9.3-1.

The longitudinal reinforcing bars in the

interlocking portion of a SCM shall have a
maximum lateral spacing of 12 inches and
need not be anchored in the footing or the
bent cap unless the bars are required for
the flexural capacity of the SCM.
Table 5.3.9.3-1 Minimum Longitudinal Bar Sizes within Interlocking Hoops
Bar size used outside the interlocking Minimum bar size required inside the
portion interlocking portion
(A bars) (B bars)
#10 #6
#11 #8
#14 #9
#18 #11
Figure 5.3.9.3-1 Longitudinal Reinforcement within Interlocking Hoops

5.4 CAPACITY PROTECTED MEMBERS

Footings, Type II shafts, bent cap Maintaining essentially elastic
beams, beam-column joints, behavior does not guarantee that the
superstructures, pile/shaft groups in bridge will provide immediate or limited
Class S1 soil, abutment stemwalls, service after a seismic event.
abutment seats, seismic expansion joints, Capacity protected members are
in-span hinge seats, and column/shaft designed and detailed to resist the
isolation casings shall be classified as overstrength moment and shear of the
capacity protected members (CPMs). adjoining seismic critical members, even
Capacity protected members shall be in locations of low seismicity where the
designed to remain essentially elastic bridge might respond elastically to the
when subjected to the overstrength design seismic hazards.
moment and shear demands of adjoining Capacity-protected members should
SCMs and sacrificial elements. have some ductility to provide insurance
against unexpected propagation of
damage from the adjoining SCMs.
The overstrength moment and shear
demands of SCMs are defined in Sections
4.4.2.1 and 4.4.2.2.
5.4.2 Flexural Capacity

The flexural capacity of CPMs shall be
taken as the nominal moment capacity
based on expected material properties,
Mne multiplied by the resistance factor of
1.0 for flexure.
Mne shall be determined by either M-ϕ
analysis as specified in Section 5.3.6.2, or
nominal flexural resistance (at Strength
limit state) as specified in AASHTO-CA
BDS using expected material properties.
Mne using M-ϕ analysis shall be based
on when either the concrete strain
reaches 0.003 or the reinforcing steel
R
strain reaches εsu as derived from the
steel stress strain model.
5.4.3 Shear Capacity

The shear capacity of CPMs shall be
taken as the nominal shear capacity,
multiplied by the resistance factor of 1.0
for shear.

The nominal shear capacity shall be

calculated in accordance with AASHTO-
CA BDS provisions using the specified
minimum material properties.
5.4.4 Superstructure and Bent Cap C5.4.4

Seismic Capacity
The capacity of the bent cap and Bent cap reinforcement required for
superstructure shall be greater than the overstrength should be developed
demand distributed to it on each side of beyond the column-to-bent cap joint.
the SCM by the largest combination of Cutting off bent cap reinforcement is
dead load moment, secondary prestress discouraged because small changes in
moment, and column earthquake the plastic hinge capacity may translate
moment, as shown in Equations 5.4.4-1 to into large changes in the moment
5.4.4-4. distribution along the cap due to steep
moment gradients.
sup(R)
≥ MdlR ± Mp/s
R R
ϕMne + Meq (5.4.4-1)
sup(L)
≥ MdlL ± Mp/s
L L
ϕMne + Meq (5.4.4-2)
sup(R)
≥ VdlR ± Vp/s
R R
ϕVne + Veq (5.4.4-3)
sup(L)
≥ VdlL ± Vp/s
L L
ϕVne + Veq (5.4.4-4)
where:
sup(R)
Mne = nominal moment capacity of
the adjacent right superstructure
span based on expected material
0.003
sup(L)
Mne = nominal moment capacity of
the adjacent left superstructure
span based on expected material
0.003
sup(R)
Vne = nominal shear capacity of the
adjacent right superstructure span
sup(L)
Vne = nominal shear capacity of the
adjacent left superstructure span
ϕ = resistance factor = 1.0 for both
flexure and shear

The strength of the superstructure The strength of the superstructure on

should not be considered effective on the the side of the column adjacent to a hinge
side of the column adjacent to a hinge seat may be considered effective by
seat. explicitly modeling that portion in the
The effective superstructure width and analysis program, including the load
effective bent cap width as specified in acting on it.
Sections 7.2.1.1, 7.3.1 and 7.3.2 shall be
used in determining the seismic capacity.
5.4.5 Transverse Reinforcement for C5.4.5

Type II Shafts
The minimum volumetric ratio of The additional confinement in the top
transverse reinforcement required for a 2 feet of the shaft is required to prevent
Type II shaft rebar cage between the top bond failure and control the opening of
of the shaft and the termination of the tensile splitting cracks in the top of the
column cage shall be as specified in shaft (Murcia-Delso et al., 2013). The
Table 5.4.5-1. experimental investigation of Murcia-
Delso et al. (2013) also shows that
structural steel casing can effectively
control tensile splitting cracks in the top of
the shaft.
If the transverse reinforcement
provided in the upper portion of Type II
shafts between the top and the
termination of the column cage results in
transverse reinforcement spacing which
violates minimum spacing requirements
in the shaft, the bar size and spacing may
be increased, or the bars may be bundled
and the spacing increased.
Table 5.4.5-1 Minimum Volumetric Ratio of Transverse Reinforcement in Type II

Shafts
Location Minimum Volumetric Ratio of Transverse Reinforcement
CISS or CIDH with All other shafts

permanent casing
Top 2 feet of shaft 50% of that required at the Same as that required at
base of the column the base of the column
Between bottom end of column 50% of that required at

cage and 2ft below top of Type II the base of the column
shaft


SECTION 6: FOUNDATIONS, ABUTMENTS, AND SOIL-FOUNDATION-STRUCTURE INTERACTION 6-1
SECTION 6
FOUNDATIONS, ABUTMENTS, AND SOIL-FOUNDATION-STRUCTURE INTERACTION
6.1 SOIL PROFILE CLASSIFICATION

Soil shall be classified as either Class Foundation soils combined with the
S1 or Class S2, depending on its structural components (i.e., piles,
properties as specified in the following footings, pile caps and drilled shafts) and
sections. the seismic input loading determine the
dynamic response of the foundation
subsystem. Typically, the soil response
has a significant effect on the overall
foundation system response. Therefore,
the anticipated foundation subsystem
response can be based on the
characteristics of the soil within the
foundation’s zone of influence.
The soil classification adopted in this
edition of the SDC is related to that used
in previous editions as follows:
• Class S1 represents competent
soils.
• Class S2 represents non-
competent soils, including
marginal soil, poor soil, soft soil,
potentially liquefiable soil and soil
susceptible to lateral spreading.
6.1.2 Class S1 Soil C6.1.2

Soils with all the following
characteristics shall be classified as Class
S1:
• Standard penetration test, (N1)60 ≥
30 (Granular soils)
• Undrained shear strength, su >
2000 psf (Cohesive soils)
• Shear wave velocity, vs > 886
ft/sec
• Not susceptible to liquefaction,
lateral spreading, or scour
where:

(N1)60 = penetration resistance

corrected for overburden pressure (N1)60 is the penetration resistance in
and hammer efficiency terms of blow count corrected to 60% of
In order to allow for the simplified the theoretical free fall energy in
accordance with ASTM D1586-11
design method for piles specified in
Section 6.2.3.2, piles shall satisfy the (ASTM, 2011) and corrected for
required embedment in Class S1 soil overburden pressure of 2 ksf.
specified in Section 6.2.3.1.
6.1.3 Class S2 Soil C6.1.3

Any soil that does not satisfy the The lateral and vertical force-
requirements of Class S1 shall be deformation responses of Class S2 soil
classified as “Class S2.” have a significant effect on the foundation
Lateral analysis as specified in response and subsequently on the overall
Section 6.2.4.2 shall be required for response of the bridge. Therefore, lateral
foundations in Class S2 soils. analysis is considered in the design.
6.2 FOUNDATIONS
6.2.1 General
Bridge foundations, including piles,
shafts, and footings (pile cap and spread
footings) shall be designed to resist
seismic loading in accordance with the
seismic performance criteria specified in
Section 1.3. Foundation components
classified as seismic critical members or
capacity protected members in
accordance with Sections 5.3.1 and 5.4.1,
respectively, shall satisfy all applicable
requirements of the SDC.
6.2.2 Footings
6.2.2.1 General
The structural design of footings shall
include flexure, one-way shear, and two
way-shear.

Flexural and shear demands shall be

based on the axial load, column
overstrength moment, and the associated
shear. Flexure and shear demands shall
not exceed the factored flexural and shear
resistances specified in Section 5 of
AASHTO-CA BDS using expected
material properties in-lieu of specified
material properties.
Footing-to-column moment resisting
joints shall be proportioned to satisfy joint
shear requirements.
6.2.2.2 Footing Joint Shear

The principal stresses in footing-to-
column moment resisting joints shall
satisfy:
Principal compression:
pc = 0.25f 'c (6.2.2.2-1)
Principal tension:
pt = 12�f 'c (6.2.2.2-2)
(In Equations 6.2.2.2-1 and 6.2.2.2-2,

f 'c and pt have units of psi)
where:
fv f 2
pt = − �� v� + vjv 2 (6.2.2.2-3)
2 2
fv f 2
pc = + �� v� + vjv 2 (6.2.2.2-4)
2 2
Tjv
vjv = ftg (6.2.2.2-5)
Beff Dftg
pile
Tjv = TC − ∑ T(i) (6.2.2.2-6)
TC = column tensile force associated

col
with Mo
pile
∑ T(i) = summation of the hold-down
force in the tension piles
ftg √2Dc Circular Column

Beff = �
Bc + Dc Rectangular Column
(6.2.2.2-7)
Pc
fv = ftg (6.2.2.2-8)
Ajh
where: With respect to Figure C6.2.2.2-1:
pc = nominal principal compressive Rectangular Column
stress
ftg
pt = nominal principal tensile stress Ajh = �Dc + Dftg ��Bc + Dftg � (C6.2.2.2-1)
fv = average normal stress in the
vertical direction Circular Column
vjv = nominal shear stress in the vertical
direction ftg π 2
Ajh = 4 �Dc + Dftg � (C6.2.2.2-2)
Dftg = depth of footing
Dc = column cross-sectional dimension
parallel to the direction of bending
Bc = column cross-sectional dimension
perpendicular to the direction of
loading
ftg
Ajh = effective horizontal area at mid-
depth of the footing, assuming a
45° spread away from the
boundary of the column in all
directions
Figure C6.2.2.2-1 Assumed Effective Dimensions for Footing Joint Stress Calculation
6.2.2.3 Effective Footing Width for

Flexure
The entire width of the footing shall be
considered effective in resisting the
column overstrength moment and the
associated shear.
6.2.2.4 Rigid Footing Response C6.2.2.4

Rigid footing behavior and the The rigid footing is commonly
associated linear distribution of pile forces assumed in calculating pile or soil
and deflections may be assumed if reactions. A finite element study on the
effects of cap stiffness on pile reactions
Lftg (Duan and McBride, 1995) shows that
≤ 2.2 (6.2.2.4-1) rigid cap assumption is valid when the
Dftg
cantilever length to thickness ratio
where: (Lftg /Dftg ) is less than or equal to 2.2.
Lftg = cantilever length of the footing or
pile cap measured from the face of
the column to the edge of the
footing
6.2.2.5 Footing Stirrups C6.2.2.5

Stirrups with 90° hooks shall not be The type of hooks used for stirrups in
allowed in footings unless the principal footings depends on the column fixity
tensile stress demand in the joint is less condition and the level of principal tensile
than 3.5�f 'c , where f 'c has the units of stress.
psi. The bar size in the footing mats along
with the principal tensile stress level and
the spacing of the mat are all critical
factors in the choice of the stirrup bar size.
Figures C6.2.2.5-1 and C6.2.2.5-2
illustrate the stirrup terminations that may
be used for columns pinned and fixed at
the base, respectively. Stirrups with 135°
hooks are not recommended due to the
difficulty in placing the stirrups during
construction.
The principal stress demand may be
reduced by increasing the depth of the
footing.
Refer to Section 6.2.2.2 for definition
of principal tensile stress.

Use of #18 bars in footings needs a

careful review as it affects the choice of
the stirrup bar and hook detailing to fit the
mat.
Note to Designer: The thickness of the expansion joint filler should allow for maximum column
deflection and prevent crushing the edge of the column concrete against the footing.
Figure C6.2.2.5-1 Footing Reinforcement – Pinned Column

Note to Designer: When precast construction is used, the 6 in. (maximum) distance for placing the first
stirrup shall be measured from the nearest edge of formed holes used for grouting extended main column
reinforcement.
Figure C6.2.2.5-2 Footing Reinforcement – Fixed Column
6.2.2.6 Spread Footings C6.2.2.6

For structural design of spread Spread footings in rock may be
footings, the distribution of bearing stress analyzed using a model similar to the
under the bottom of the footing shall be simplified model for piles as specified in
assumed linear. Section 6.2.3.2.
Spread footings shall satisfy the For additional information on spread
following requirements: footings, refer to Section 10 of AASHTO-
• The bearing stress shall not CA BDS.
exceed the factored nominal
bearing resistance for seismic
(Extreme Event I) provided by the
geo-professional
• The sliding force shall not exceed
the factored sliding resistance
determined in accordance with
Section 10 of AASHTO-CA BDS
• The eccentricity of loading for
seismic (Extreme Event I) shall
satisfy the requirement of Section
10 of AASHTO-CA BDS

6.2.3 Pile Foundations in Class S1 Soil

6.2.3.1 General C6.2.3.1
Piles founded in Class S1 soils may be Foundations embedded in Class S1
analyzed and designed using the soils are capable of resisting design
simplified model as specified in Section forces during an earthquake while
6.2.3.2 if: experiencing small deformations. This
• The pile cap satisfies the stiffness type of performance characterizes a stiff
requirement specified in Section foundation subsystem that usually has an
6.2.2.4 insignificant impact on the overall
• The pile layout is symmetrical dynamic response of the bridge. Lateral
about the X- and Y- axes and all analysis is typically ignored in the demand
piles have the same cross- and capacity assessments for
sectional area foundations in Class S1 soils.
• The upper portion of the pile The minimum required embedment is
measured from the pile cut-off associated with all Class 90, 140, and 200
elevation or finish grade piles and other small diameter piles which
(whichever is lower) is embedded include piles with a diameter and/or width
in a class S1 soil profile. of 24 inches or less. For these small
For granular materials, the upper diameter piles, a simple correlation
portion of the pile shall be taken as related to pile size could not be developed
the greater of 8 pile due to many variables such as pile types,
diameters/widths and 20 feet. sizes, materials, etc. Therefore, a
For cohesive materials, the upper minimum embedment depth is used.
portion of the pile shall be taken as A comprehensive analysis entails a
the greater of 6 pile lateral analysis of the foundation and its
diameters/widths and 15 feet. components with all applicable soil
springs.
Pile foundations that do not satisfy the
above three conditions shall require a
comprehensive design as specified in
Section 6.2.4.2.
Pile caps shall be designed as
footings as specified in Section 6.2.2.

6.2.3.2 Simplified Design for Piles in C6.2.3.2

Class S1 Soil
For calculating axial force demands on
The axial force demands,
pile
C(i) for piles, the simplified model assumes that
pile the demand due to plastic shear of the
compression and for tension, shall
T(i) column at the pile-to-cap connection is
not exceed the factored nominal seismic ignored due to the reserve capacity
resistance provided by the geo- inherent in pile group-supported footing
professional. systems in Class S1 soil. The reserve
The axial force demand on an capacity includes contributions from
individual pile when the column reaches passive soil resistance and side friction on
its overstrength moment, as shown in the pile cap, which in combination with the
Figure 6.2.3.2-1, shall be taken as: competent properties of Class S1 soil,
limits the lateral translation of the piles
pile col col
C(i) Pp λ Mo(y) d(i)x λ Mo(x) d(i)y and results in low moment demand. This
pile �= ± ± assumption is consistent with the
T(i) Np Ip.g.(y) Ip.g.(x)
observed response of similar foundations
(6.2.3.2-1) during past earthquakes.
where: Equation 6.2.3.2-1 provides axial force
in the piles based on linear variation of
2
Ip.g.(x) = ∑ nd(i)y (6.2.3.2-2) axial force in the piles (rigid pile cap) when
axial force and overstrength moment at
2
Ip.g.(y) = ∑ nd(i)x (6.2.3.2-3) the base of the column are applied to the
foundation. The load reduction factor, λ
pile
C(i) = axial compression force demand accounts for redundancy in the pile group
considering the fact that applied loads can
on pile (i)
pile be redistributed among the piles and
T(i) = axial tension force demand on pile overloading of any pile does not
(i) necessarily result in collapse of the
Pp = total axial load on the pile group foundation.
including column axial load (dead For pile cap design, the load reduction
load + EQ load), footing weight, factor is 1.0 as caps are capacity
and overburden soil weight protected members and are designed to
Np = total number of piles in the pile resist the column overstrength moment.
group For pile group design, however, a
λ = load reduction factor for a pile reduction in the design moment demand
group, 1.0 for pile cap design, 0.83 from Mo to Mp (i.e., λ = 1/1.2 = 0.83) is
for pile design adjudged to be reasonable in view of built-
col
Mo(x) = component of the column in redundancy due to group effects.
overstrength moment demand
about the X axis
col
Mo(y) = component of the column
overstrength moment demand
about the Y axis

Figure 6.2.3.2-1 Simplified Pile Model for Foundations in Class S1 Soil

d(i)x = distance from pile (i) to the

centerline of the column along the
X axis
d(i)y = distance from pile (i) to the
centerline of the column along the
Y axis
Ip.g.(x) = moment of inertia of the pile
group about the X axis
Ip.g.(y) = moment of inertia of the pile
group about the Y axis
n = total number of piles at distance d(i)
from the centroid of the pile group
Pile groups in Class S1 soil shall resist The nominal shear resistance of piles
the shear demand from the column. The in Class S1 soils are provided in
factored nominal shear resistance of the Attachment 1 of MTD 5-1. The
piles shall be greater than the plastic contribution of passive soil pressure may
col
shear demand, Vo at the bottom of the be added to the shear resistance obtained
column. from Attachment 1 of MTD 5-1.
Pre-designed piles with wire
confinement as shown in Caltrans
‘Standard Plans,’ may only be used in
Class S1 soils.
6.2.4 Pile Foundations in Class S2 Soil

6.2.4.1 General C6.2.4.1
The foundation system shall be In Class S2 soils the pile cap rotation
designed to resist the demands imposed may be accompanied by significant lateral
by the overstrength moment and shear displacements.
force of the columns and the lateral The designer should select the most
displacement of the foundation cost-effective strategy for increasing the
considering soil-foundation-structure lateral resistance of the foundation when
interaction. required. The following methods are
The axial force demand shall not commonly used to increase lateral
exceed the factored nominal seismic foundation capacity.
resistance provided by the geo- • Increase the amount of fixity at the
professional. pile-to-footing connection and
The piles shall maintain their axial load strengthen the upper portion of the
capacity at the expected lateral pile
displacement. • Use a more ductile pile type that
If the deformation demand creates can develop soil resistance at
plastic hinging in the piles, the piles shall larger pile deflections
be designed as seismic critical members. • Add additional piles or use larger
piles
Piles supporting bents shall be fixed at

the pile-to-cap connections. The pile-to-
cap connections for piles supporting
abutments may be pinned, fixed, or
partially fixed.
Concrete piles shall have a minimum
confinement reinforcement of #4 spiral or
hoop reinforcement.
6.2.4.2 Comprehensive Foundation C6.2.4.2

Design Simplified Model for Pile Foundations in
Pile/shaft foundations in Class S2 Class S2 Soil
soils shall be analyzed using Inelastic The axial force demand on an
Static Analysis (ISA) as specified in individual pile when the column reaches
Section 5.2.2, including soil-foundation- its overstrength moment and the top of
structure interaction, as illustrated in piles reach their plastic moment capacity,
Figure 6.2.4.2-1. For preliminary design, pile
pile foundations in Class S2 soils may be Mp as shown in Figure C6.2.4.2-1, is
analyzed using a simplified model. approximated by:
However, ISA shall be performed for the
pile
final design of the foundation. C(i) Pp
pile � = Np
T(i)
col col pile
�Mo(y) + Vo(x)Dftg + Np Mp(y) �d(i)x
± Ip.g.(y)
col col pile
�Mo(x) + Vo(y)Dftg + Np Mp(x) � d(i)y
± Ip.g.(x)
(C6.2.4.2-1)
where:
pile
Mp(x) = component of the pile plastic
moment capacity at the pile cap
connection due to total average
axial load about the X axis
pile
Mp(y) = component of the pile plastic
moment capacity at the pile cap
connection due to total average
axial load about the Y axis
col
Vo(x) = component of column overstrength
shear demand along the X axis
col
Vo(y) = component of column overstrength
shear demand along the Y axis

Notes:
1. All springs are not shown
2. All spring types may not be applicable to a given soil
Figure 6.2.4.2-1 Inelastic Static Analysis of Foundations

Figure C6.2.4.2-1 Simplified Pile Model for Foundations in Class S2 Soil

6.2.4.3 Scour and Liquefaction C6.2.4.3

Considerations
For soils susceptible to scour and/or For the scourable layer, the
liquefaction, the lateral analysis shall be occurrence condition implies a 100%
based on the occurrence and non- scour (i.e., Degradation and Contraction
occurrence conditions using appropriate scour). For a potentially liquefiable layer,
soil stiffness provided by the geo- the occurrence condition implies that the
professional. soil liquefies. Both scenarios are needed
to design for deformation and flexural
Case 1 – Potentially Liquefiable Layer demands.
Only The non-occurrence condition which
implies that neither scour (i.e.,
For potentially liquefiable layer Degradation, Contraction, and Local
existing within 50 feet from the ground scour) nor liquefaction occurs, is needed
surface, lateral analysis shall use to design for shear demand. For
liquefied soil stiffness (springs) for the additional information on Degradation,
liquefiable layer and a reduced soil Contraction, and Local scour, refer to
stiffness for the soil above the liquefiable Section 2 of AASHTO-CA BDS.
layer. For potentially liquefiable soil layers
at deeper depths, a PSDC shall be
developed.
Case 2 – Scourable Layer Only

If the soil is susceptible to scour
(degradation and contraction) only, lateral
analysis shall be performed assuming
there are no soil springs for the scour
layer or layers above it.
Case 3 – Combination of Potentially

Liquefiable and Scourable Layers
If the liquefiable layer is below the
scourable layer, lateral analysis shall use
liquefied soil stiffness (springs) for the
liquefiable layer and no soil springs for the
scour layer. If the liquefiable layer is
above the scourable layer, lateral analysis
shall be performed assuming no soil
springs for both layers.

6.2.5 Shafts
6.2.5.1 General C6.2.5.1
All shafts shall be constructed with Type I shafts are designed so the
diameters equal to or greater than the plastic hinge will form below ground in the
maximum dimension of the supported shaft. However, the plastic hinge may
column. form above the ground if steel casing is
Type I shafts shall be designed such used below ground.
that the cross section of the confined core Type II shafts are designed larger than
is the same for both the column and the the column so that the plastic hinge will
shaft, but the concrete cover and area of form at or above the shaft-to-column
transverse and longitudinal reinforcement interface, thereby containing the majority
may change between the column and the of inelastic action in the ductile column
shaft, as shown in Figure 6.2.5.1-1. member.
Type-II shafts shall be at least 24 Where a shaft supports an oblong
inches larger than the maximum and/or a relatively short column, pinning
dimension of the supported column, as the base of the column to the shaft will
shown in Figure 6.2.5.1-1. result in a decrease in the size (i.e.,
Shafts supporting columns by means diameter and/or length) of the shaft and a
of a pin between the column base and the consequent decrease in the foundation
top of the shaft shall be designed as cost. For shafts connected to columns by
capacity protected members based on the a pin, the overstrength moment demand
overstrength shear and moment (if any) at the base of the column is taken as zero
demands at the base of the column. If a if a solid or pipe section with a cover pipe
reduced diameter reinforcement cage is is used to form the pinned connection. If a
used to form the pinned connection, the reduced diameter reinforcement cage is
pin rebar cage shall be developed in both used to form the pinned connection, the
the column and the shaft. If a pipe or solid moment demand at the base of the
steel section is used to form the pinned column is taken as the overstrength
connection, the lower portion of the moment transmitted by the pin
pipe/solid section shall be developed in reinforcement cage. The overstrength
the shaft. shear at the base of the column may be
Reinforcing bar clearance obtained by dividing the sum of the
requirements for drilled shafts as overstrength moments at the top and
specified in Section 10 of AASHTO-CA bottom of the column (if any) by the
BDS, shall be maintained. column height.

While it is common to design Type II

shafts to be 24 inches larger than the
column dimension, greater enlargements
may be required to satisfy clearance
requirements, or to reduce the depth of
the shaft. In general, excessive
enlargement of the shaft should be
avoided for economic reasons. If the
required shaft size dictated by a Class S2
soil condition is too large, the designer
may consider using a CISS pile or other
foundation types such as Type I shaft.
Type II Shafts will increase the
foundation costs, compared to Type I
Shafts, however there is an advantage of
improved post-earthquake inspection and
repair.
NOTE:
Hoop reinforcement only shown. Transverse reinforcement may be hoops or spirals as
specified in Sections 8.2.2.3 and 8.2.3.2.
Figure 6.2.5.1-1 Shaft Types

For structures with unequal column

heights, Type I shafts can increase the
effective length of the relatively short
columns. Type II shafts can decrease the
effective length of shaft extensions. The
end result will be a structure with a
balanced stiffness as discussed in
Section 7.1.2.
Refer to Section 10 of AASHTO-CA
BDS for spacing, clearance, and cover
requirements for drilled shafts.
Conventional standard sizes for CIDH
piling are provided in Attachment 3 of
MTD 3-1.
6.2.5.2 Flexure and Shear Demands on

Type I Shafts
Type I shafts shall be designed as
seismic critical members, as specified in
Section 5.3.
6.2.5.3 Flexure and Shear Demands on C6.2.5.3

Type II Shafts
Type II shafts shall be designed as The distribution of moments along a
capacity protected members. The shaft is dependent upon the geotechnical
factored moment capacity,ϕMne at any properties of the surrounding soil and the
location along the shaft shall satisfy: stiffness of the shaft.
• Type II shafts cast in dry or Any change in the size of the shaft to
dewatered hole meet the column overstrength demand
will affect the soil springs and the resulting
MD ≤ ϕMne (6.2.5.3-1) moment and shear demand in the shaft.
Therefore, it may require iteration to
• Type II shafts cast using slurry- achieve a satisfactory design.
displacement method
MD ≤ 0.8ϕMne (6.2.5.3-2)
where:
MD = moment demand at any location
generated by the column’s
overstrength moment and
associated shear.

The factored shear capacity, Vn at any The current design criteria for type II
location along the shaft shall satisfy: shafts will streamline the shaft design and
remove excessive conservatism from
VD ≤ ϕVn (6.2.5.3-1) shafts cast in dry or dewatered holes. In
the dry condition, placing the rebar cage
where: and concrete inside the shaft is under a
VD = shear demand at any location controlled environment with minimal
generated by the column’s chances of soil caving and anomalies.
overstrength moment and Due to the additional risk and quality
associated shear. assurance challenges associated with
construction under wet conditions, the
factored moment capacity is limited to
0.8ϕMne , resulting in an additional factor
of safety of 1.25 for type II shafts cast
using the slurry-displacement method.
Since specified (nominal) material
properties, instead of expected material
properties are used for shear design, the
factor of safety of 1.25 shall not apply to
the shear design of Type II shafts.
Typical moment and shear diagrams
for a Type II shaft in the transverse
direction are illustrated in Figures
C6.2.5.3-1 and C6.2.5.3-2. The moment
and shear demands in both the
transverse and longitudinal directions are
considered in the design.

Figure C6.2.5.3-1 Typical Moment Diagrams for Type II Shafts
Figure C6.2.5.3-2 Typical Shear Diagram for Type II Shafts

6.2.5.4 Pile and Shaft Extensions

Piles and shafts extended above the
ground shall have a minimum
confinement of #4 spiral/hoop
reinforcement for the entire length of the
pile/shaft. The column section shall meet
the ductility requirements of SCMs, as
specified in Sections 3.5, 4.4.1 and 5.3.
All requirements of Type I and Type II
shafts shall also be satisfied.
6.2.6 Lateral Stability of Piles and C6.2.6

Shafts
Lateral stability analysis shall be Lateral stability analysis is
performed for piles and shafts to accomplished by applying the governing
determine the tip elevation for horizontal design lateral load and the dead load at
loading based on the following the top of the column over a range of
assumptions: pile/shaft lengths and recording the
• The governing design lateral load resulting top of pile/shaft deflections, as
and the dead load are applied at shown in Figure C6.2.6-1.
the top of the pile/shaft Pile/shaft group founded in class S1
• The effects of scour and soil is laterally stable. Therefore, lateral
liquefaction are considered, if stability analysis is not required for
applicable pile/shaft groups in class S1 soil.
• The critical length for lateral
stability is the embedded length of
pile for which greater lengths do
not result in a reduction of 5% or
more in the deflection at the
pile/shaft cut-off elevation.
The length of pile/shaft for lateral

stability shall be greater than or equal to
the critical length multiplied by the
Embedment Factor shown in Table 6.2.6-
1.
Table 6.2.6-1 Embedment Factor for Pile Tip Elevation
Pile/Shaft Embedment Factor
Pile/shaft groups in Class S2 soil 1.0
Shafts (Types I and II) in multi-column bents 1.0
Shafts without rock sockets in single-column bents 1.2
Shafts with rock sockets in single-column bents 1.0 (for CIDH portion)
1.2 (for rock socket portion)

Figure C6.2.6-1 Lateral Stability Analysis of Piles and Shafts

6.3 ABUTMENTS
6.3.1 Longitudinal Stiffness
6.3.1.1 General C6.3.1.1
For ESA and EDA, effective stiffness The backfill passive pressure force
obtained from an idealization of the initial resisting movement at the abutment
stiffness of the nonlinear abutment- varies nonlinearly with longitudinal
backfill force-deformation curve as shown abutment displacement and is dependent
in Figure 6.3.1.2-1 shall be used. For ISA, upon the material properties of the
a bilinear force-deformation curve backfill. While the full nonlinear abutment
incorporating effective stiffness, as shown backbone curve or the bilinear
in Figure 6.3.1.2-1, shall be used. representation of the backbone curve
may readily be used with NTHA, the
bilinear representation of the backbone
curve is most suited for ESA, EDA, and
ISA.
For information on the full nonlinear
force-deformation relationship, refer to
Shamsabadi et al. (2007) for straight
abutments or Rollins and Jessee (2013)
for skew abutments.
The bilinear model presented herein is
based on experimental and calibrated
analytical models using engineered
structural backfill to a relative compaction
of at least 95%.
6.3.1.2 Bilinear Model C6.3.1.2

Effective abutment stiffness, Keff as For seat-type abutments, the
shown in Figure 6.3.1.2-1, shall be expansion hinge gap, Δgap is taken into
determined as: consideration in determining the effective
abutment wall stiffness as shown in
F Figure 6.3.1.2-1 and Equation 6.3.1.2-2.
Keff = Δabut (6.3.1.2-1)
eff The idealized ultimate passive capacity
given by Equation 6.3.1.2-4 is based on
Δgap + Δabut (seat abutment) nonlinear hyperbolic backbone curves
Δeff = �
Δabut (diaphragm abutment) fitted by Shamsabadi et al. (2010) to the
(6.3.1.2-2) Force-Displacement data from passive
Fabut earth pressure tests on large-scale
Δabut =K (6.3.1.2-3)
abut abutment and pile cap tests (Maroney,
1995; Stewart et al., 2007; Rollins and
2.5 Cole, 2006; Rollins and Jessee, 2013)
5.5 h
Fabut = wabut �1+2.37abut � Rsk and subsequent bilinear idealization of
habut
the hyperbolic backbone curves.
(6.3.1.2-4)

Figure 6.3.1.2-1 Nonlinear Abutment Model
Kabut = wabut (5.5habut + 20)Rsk (6.3.1.2-5) The ultimate force in the bilinear
model was calibrated such that the
Rsk = e−θ⁄45 (6.3.1.2-6) potential energy (the area below the
Force-Displacement curve) stored within
θ ≤ 66° (6.3.1.2-7) the backfill due to translational movement
where: of the superstructure, equals that of the
nonlinear hyperbolic force-displacement
Keff = effective abutment longitudinal curve (Shamsabadi and Rollins, 2014).
stiffness (k/in) For skewed abutments, the ultimate
Fabut = idealized ultimate passive capacity capacity and stiffness are reduced by a
of the backfill behind abutment reduction factor, Rsk . The skew reduction
backwall or diaphragm (kip). In factor was calibrated by Shamsabadi and
Figure 6.3.1.2-1, Fabut = Fbw (for Rollins (2014) against experimental data
seat abutment), and Fabut = Fdia from full-scale abutment tests on 0, 15,
(for diaphragm abutment) 30, 45-degree skew angles (Stewart et
Δeff = effective abutment longitudinal al., 2007; Rollins and Jessee, 2013) as
displacement when the passive well as from Finite Element simulation
force reaches Fabut (in.) models for 60° skewed abutment.
Δgap = width of expansion gap at seat The skew reduction factor accounts
abutment (in.) for the increased tendency for skew
Δabut = abutment displacement at bridges to rotate and translate when
idealized yield (in.) subjected to seismic ground motions. The
Kabut = abutment longitudinal stiffness as resulting deformation leads to a partial
shown in Figure 6.3.1.2-1 (kip/in) loss of contact between the abutment and
Rsk = skew reduction factor the backfill with consequent decrease in
θ = abutment skew angle (degrees) abutment stiffness.
The limiting skew angle of 66° is
based on bridge geometries observed in
California.

habut = height of backwall or diaphragm as Figure C6.3.1.2-1 schematically

shown in Figure 6.3.1.2-2 (ft); 2ft ≤ shows the stiffness reduction due to skew
habut ≤ 10ft. In Figure 6.3.1.2-2, angle, where K represents Kabut for non-
habut shall be taken as hbw for seat skew, Kθ represents Kabut for abutment
**
abutments, hdia for diaphragm with θ (degree) skew, and Fbw represents
abutments designed for full soil Fabut for abutment with θ (degree) skew.
*
pressure, and as hdia for
diaphragm abutments not
designed for full soil pressure.
wabut = abutment width along the skew
direction (ft) as shown in Figure
6.3.1.2-3. wabut = wbw for seat
abutment and wdia for diaphragm
abutment, as shown in Figure
6.3.1.2-2.
For bridges with abutment skews

greater than 66°, the longitudinal stiffness Figure C6.3.1.2-1 Reduction of Force
shall be taken equal to zero. and Stiffness for Skewed Abutments
For seat abutments, the backwall is

typically designed to break off in order to
protect the foundation from inelastic
action.
For diaphragm abutments the entire
diaphragm, above and below the soffit, is
typically designed to engage the backfill
immediately upon longitudinal movement
of the bridge. Therefore, the effective
abutment area is equal to the entire area
of the diaphragm. If the diaphragm has
not been designed to resist the passive
earth pressure exerted by the abutment
backfill, the effective abutment area is
limited to the portion of the diaphragm
above the fracture plane.
The limitation on abutment backwall
heights (i.e., 2 to 10 feet) is based on the
heights of experimentally tested or
analytically simulated backwalls.

w bw w dia
*
h bw h dia
**
h dia
Seat Abutment Diaphragm Abutment

Figure 6.3.1.2-2 Effective Abutment Area
Figure 6.3.1.2-3 Effective Abutment Width for Skewed Bridges
6.3.1.3 Displacement Coefficient C6.3.1.3

The abutment displacement
coefficient, RA shall be used in the
assessment of the effectiveness of the
abutment.
Δ
RA = Δ D (6.3.1.3-1)
eff
where:
ΔD = longitudinal displacement demand
from elastic analysis-obtained as
specified in Section 4.2.1 and
4.2.2.

• For RA ≤ 2:
The linear elastic model may be used For RA ≤ 2: The response is
directly to determine the displacement dominated by the abutments.
demand of the bents or frame.
• For RA ≥ 4: For RA ≥ 4: The abutment

The effective abutment stiffness, Keff participation in the bridge response is
in the elastic model shall be reduced to a assumed to be minimal and hence
minimum residual stiffness, Kres . insignificant to the longitudinal seismic
Kres shall be taken as: performance. The bents and frames will
sustain significant deformation.
Kres = 0.1Keff (6.3.1.3-2) The residual spring stiffness, Kres has
no relevance to the actual stiffness
The elastic analysis shall be repeated provided by the failed backwall or
to obtain revised bent displacements. diaphragm but should suppress
unrealistic response modes associated
with a completely released end condition.
• For 2 < RA < 4: For 2 < RA < 4: The abutment

adj participation in the bridge response is
An adjusted effective stiffness, Keff assumed to be moderate. The abutment
adj
shall be used in the elastic model. Keff stiffness in the elastic model is adjusted
shall be taken as: by interpolating effective abutment
stiffness between Keff and the residual
adj
Keff = Keff [1 − 0.45(RA − 2)] (6.3.1.3-3) stiffness Kres based on the RA value.
where:
adj
Keff = effective abutment longitudinal
stiffness adjusted for displacement
coefficient (kip/in)
The elastic analysis shall be repeated

to obtain revised bent displacements.

6.3.2 Transverse Stiffness C6.3.2

A nominal transverse spring stiffness, Seat type abutments are designed to
Knom equal to 50% of the elastic resist transverse service load and
transverse stiffness of the adjacent bent moderate levels of ground motion
may be used at the abutment in the elastic elastically. Linear elastic analysis cannot
demand assessment models. capture the inelastic response of the
Any additional element such as shafts shear keys, wingwalls, or piles. The
(used for transverse ductility), shall be transverse capacity of seat abutments
included in the transverse analysis with a should not be considered effective for the
characteristic force-deflection curve. The design seismic hazards unless the
initial slope of the force-deflection curve designer can demonstrate the force-
shall be included in the elastic demand deflection characteristics and stiffness for
assessment model. each element that contributes to the
Transverse stiffness of diaphragm transverse resistance.
type abutments supported on standard The magnitude of the transverse
piles surrounded by dense or hard abutment stiffness and the resulting
material may conservatively be displacement is most critical in the design
estimated, ignoring the wingwalls, as 40 of the adjacent bent, and not the
kip/in per pile. abutment itself. Reasonable transverse
displacement of the superstructure
relative to the abutment seat can easily be
accommodated without catastrophic
consequences.
The nominal spring stiffness, Knom has
no direct correlation or relevance to the
actual residual stiffness (if any) provided
by the failed shear key but should
suppress unrealistic response modes
associated with a completely released
end condition.
Use of Knom for abutment transverse
stiffness is consistent with the stand-
alone pushover analysis-based design of
the adjacent bents and it is conservative
since additional amounts of lateral
resistance at the abutments that are not
generally captured by the nominal spring
will only reduce the transverse
displacement demands at the bents.

6.3.3 Support Length C6.3.3

The support length normal to the Sufficient abutment support length is
centerline of the backwall, NA shall provided to accommodate the anticipated
satisfy: thermal movement, prestress shortening,
creep, shrinkage, and the relative
MR + Δeq + L longitudinal earthquake displacement, as
NA ≥ � 1
Ds (6.3.3-1) shown in Figure 6.3.3-1.
3 For abutments skewed at an angle θ,
30 inches the resulting support length measured
where: along the longitudinal axis of the bridge is
(NA ⁄cos θ).
NA = abutment support length as shown The term Movement Range (MR) is
in Figure 6.3.3-1 (in.) equivalent to “Movement Rating,” as
MR = movement range, i.e., total previously used in Caltrans practice.
anticipated joint movement from Elastomeric and
the widest to the narrowest Polytetrafluoroethylene (PTFE) spherical
opening (in.) bearings may be used at bridge
L = pad dimension along the bridge for abutments but only PTFE spherical
elastomeric bearings (in.), or bearings are allowed at in-span hinges.
length of masonry plate for PTFE
spherical bearings (in.)
Ds = depth of superstructure at the bent
cap (in.)
Δeq = displacement demand for the
frame adjacent to the abutment
(in.). Displacement of the abutment
is assumed to be zero.
In Figure 6.3.3-1, a = thickness of joint

filler.
Figure 6.3.3-1 Abutment Support Length Requirements

6.3.4 Shear Key Design C6.3.4

The shear key force demand, Fsk , for Typically, abutment shear keys are
abutments supported on piles and spread expected to transmit the lateral forces
footings shall be determined as: generated by small to moderate
earthquakes and service loads.
• For abutment on piles
Determining the earthquake force
demand on shear keys is difficult. The
Fsk = α�0.75Vpiles + Vww � (6.3.4-1)
forces generated with elastic demand
assessment models should not be used to
• For abutment on spread footing
size the abutment shear keys.
Fsk = α(0.5Pdl ) (6.3.4-2) Wide bridges may require internal
shear keys to ensure adequate lateral
in which: resistance is available for service load
and moderate earthquakes. Internal
0.5 ≤ α ≤ 1 (6.3.4-3) shear keys should be avoided whenever
possible because of maintenance
where: problems associated with premature
failure caused by binding due to
Fsk = shear key force demand (kip)
superstructure rotation or shortening.
Vpiles = sum of lateral geotechnical
For design, the adjustment factor for
capacity of the piles (kip) shear key demand, α equal to 1 should be
Vww = shear capacity of one wingwall assumed initially. Subsequently, α may be
(kip) reduced as needed to produce an
Pdl = superstructure dead load reaction acceptable design.
at the abutment plus the weight of In Equation 6.3.4-1, the factor 0.75 is
the abutment and its footing (kip) a safety factor that accounts for the
α = adjustment factor for shear key uncertainty in estimating the lateral
force demand geotechnical capacity of the piles.
In Equation 6.3.4-2, the factor 0.5
For cases where the geotechnical
represents the coefficient of friction
capacity of the piles or the nominal sliding
between the footing and the underlying
resistance of the spread footing is
soil.
unusually large, the shear key force
For information on lateral capacity of
demand of Equations 6.3.4-1 and 6.3.4-2
piles, refer to Attachment 1 of MTD 5-1.
shall be taken, respectively, as:
Lateral capacity of piles may also be
sup obtained from “LPILE” analysis.
Fsk = αPdl ≤ α�0.75Vpiles + Vww �
The shear capacity of wingwall may be
(6.3.4-4) determined in accordance with the shear
sup
Fsk = αPdl ≤ α(0.5Pdl ) (6.3.4-5) resistance provisions of AASHTO-CA
BDS Section 5.
where:
sup
Pdl = superstructure dead load reaction
at the abutment (kip).

6.3.5 Shear Key Reinforcement C6.3.5

Abutment shear key reinforcement A shear key is isolated when a smooth
shall be designed using either the Isolated construction joint is used at the shear key
key method or the Monolithic (i.e., Non- interfaces with the stemwall and backwall
isolated) key method, as shown in Figures and only specifically designed
6.3.5-1 and 6.3.5-2, respectively. reinforcement crosses the interface.
The horizontal reinforcement in the Due to development length
stem wall below the shear key shall be requirements, it is recommended that
designed to carry the shear key force vertical shear key reinforcement be no
elastically. larger than #11 bars.
For shear keys reinforced with headed In situations such as non-standard
bars, the minimum development length of overhangs, high skews, and retrofit
full-size headed bars shall be taken as conditions at widenings where the size of
14db. the shear key is not adequate to develop
straight bars, hooks or headed bars may
be used. Headed bars are recommended
in place of large radius hooks.
A full-size Headed bar has a net head
area equal to nine times the cross-
sectional area of the bar (i.e., 9Ab ).
* Smooth construction joint is required at the shear key interfaces with the stemwall and backwall to
effectively isolate the shear key. These interfaces shall be trowel-finished smooth before application of a
bond breaker such as construction paper. Form oil shall not be used as a bond breaker for this purpose.
NOTES:
(a) Not all shear key bars shown
(b) On high skews, use 2-inch expanded polystyrene with 1-inch expanded polystyrene over the 1-inch
expansion joint filler to prevent binding on post-tensioned bridges.
Figure 6.3.5-1 Isolated Shear Key Reinforcement Details

(B) Monolithic Shear Key

NOTES:
(a) Not all shear key bars shown
(b) On high skews, use 2-inch expanded polystyrene with 1-inch expanded polystyrene over the 1-inch
expansion joint filler to prevent binding on post-tensioned bridges.
Figure 6.3.5-2 Monolithic Shear Key Reinforcement Details
6.3.5.1 Isolated Key C6.3.5.1

• Vertical Reinforcement Equations 6.3.5.1-1, 6.3.5.1-2, and the
reinforcement details shown in Figure
The required area of interface shear
6.3.5-1 are based on experimental tests
reinforcement, Ask crossing the shear
on exterior shear keys (Bozorgzadeh et
plane, shall be taken as:
al., 2007). The reinforcing detail was
Fsk developed to ensure that exterior shear
Iso
Ask = (6.3.5.1-1) keys fail through a well-defined horizontal
1.8fye
plane that is easily repaired after an
The shear key vertical reinforcement earthquake.
shall be placed in a single line parallel to A minimum horizontal distance, Lmin
the bridge centerline and located within as shown in Figure 6.3.5-1 should be
the middle third of the shear key base as provided. Lmin is determined as:
shown in Figure 6.3.5-1.
Lmin,hooked = 0.6(a + b) + ldh (C6.3.5.1-1)
Lmin,headed = 0.6(a + b) + 3 (C6.3.5.1-2)

• Shear Key Confinement where:

Reinforcement Lmin = minimum horizontal distance from
Shear key confinement reinforcement the vertical shear key bars to the
shall be a minimum of #4 bars at 12 hooked or headed end of the
inches on center in all directions placed at lowest layer of hanger bars (in.)
the periphery of the key block, as a = vertical distance from the location
illustrated in Figure 6.3.5-1. of the applied force on the shear
key to the top surface of the stem
• Horizontal Reinforcement in the wall, taken as one half the vertical
Stem Wall (Hanger Bars) length of the expansion joint filler
The area of horizontal reinforcement plus the pad thickness (in.), as
in the stem wall, Ash shall be taken as: shown in Figure 6.3.5-1
b = vertical distance from the top
Iso surface of the stem wall to the
Ash = 2Ask(provided) (6.3.5.1-2)
centroid of the lowest layer of
shear key horizontal reinforcement
where:
(in.), as shown in Figure 6.3.5-1
Iso
Ask(provided) = area of interface shear ldh = development length in tension of
reinforcement provided (in.2) standard hooked bars as specified
in AASHTO-CA BDS (in.)
The size of the horizontal

reinforcement in the stem wall may be
varied as needed to ensure the shear key
vertical reinforcement is located within the
middle third of the shear key base.
6.3.5.2 Monolithic Key C6.3.5.2

• Vertical Reinforcement Shear key construction using normal
weight concrete placed monolithically is
The area of interface shear
assumed.
reinforcement crossing the shear plane,
Ask shall be taken as:
mono 1
Ask = (F − 0.4Acv ) (6.3.5.2-1) Equations 6.3.5.2-1 to 6.3.5.2-4 are
1.4fye sk
based on the interface shear transfer-
in which: shear friction provisions of AASHTO-CA
BDS.
0.25 f 'ce Acv
0.4Acv < Fsk ≤ min � 1.5 Acv
�
(6.3.5.2-2)
0.05A
≥ _____cv
mono
Ask (6.3.5.2-3)
fye

where:
Acv = area of concrete engaged in
interface shear transfer (in.2)
fye = expected yield stress for A706
reinforcement (ksi)
f 'ce = expected compressive strength of
unconfined concrete (ksi)
• Horizontal Reinforcement in the

Stem Wall (Hanger Bars)
The area of horizontal reinforcement
in the stem wall, Ash shall be determined
as:
mono
2Ask(provided)
Ash = max � (6.3.5.2-4)
Fsk ⁄fye
where:
mono
Ask(provided) = area of interface shear
reinforcement provided for
monolithic shear key.

SECTION 7: BRIDGE COMPONENTS 7-1
SECTION 7
BRIDGE COMPONENTS
7.1 FRAMES
7.1.1 Frame and Bent Proportioning C7.1.1
Bridge frames shall be proportioned to The best way to increase a structure’s
achieve a balance in the stiffness and likelihood of responding to seismic attack
geometry. in its fundamental mode of vibration is to
balance its stiffness and mass
distribution. Irregularities in geometry
increase the likelihood of complex
nonlinear response that cannot be
accurately predicted by elastic modeling
or plane frame inelastic static modeling.
7.1.2 Balanced Stiffness C7.1.2

The effective stiffness-to-mass ratio An increase in superstructure mass
between any two bents within a frame or along the length of the frame should be
between any two columns within a bent accompanied by a reasonable increase in
shall satisfy the requirements specified in column stiffness, as shown in Figure
Table 7.1.2-1. C7.1.2-1.
The effective stiffness-to-mass ratio The following considerations are taken
between adjacent bents within a frame or into account when calculating effective
between adjacent columns within a bent stiffness: framing effects, end conditions,
shall satisfy the requirements specified in column height, percentages of
Table 7.1.2-1 longitudinal and transverse column steel,
The effective stiffness of a bent or column diameter, and foundation
column shall be based on effective flexibility.
section properties as specified in Section Some of the consequences of
3.4. unbalanced stiffness include:
In Table 7.1.2-1: • Increased damage in the stiffer
e
ki = effective stiffness of bent or elements
column i (kip/in.) • An unbalanced distribution of
e
kj = effective stiffness of bent or inelastic response throughout the
column j (kip/in.)
structure
mi = tributary mass of bent or column i
(kip- sec2/in.) • Increased column torsion
mj = tributary mass of bent or column j generated by rigid body rotation
(kip-sec2/in.) of the superstructure

Table 7.1.2-1 Column/Bent Stiffness-to-Mass Ratios for Bents/Frames
Column/Bent Stiffness-to-Mass Ratio

e
For any two bents in a frame k
� i �
mi
or 0.5 ≤ e ≤ 2.0 (7.1.2-1)
kj
any two columns in a Bent �
mj �
e
For adjacent bents in a frame k
� i �
mi
or 0.75 ≤ e ≤ 1.33 (7.1.2-2)
kj
adjacent columns in a Bent �
mj �
The following techniques may be used

to satisfy the requirements of Table 7.1.2-
1.
• Use oversized shafts
• Adjust effective column lengths
(i.e. lower footings using isolation
casing)
• Modify column end conditions
• Reduce/redistribute superstructure
mass
• Vary the column cross section and
longitudinal reinforcement ratios
• Add or relocate columns/bents
• Modify the hinge/expansion joint
layout
Section 7.6.1 provides additional

information on optimizing the
performance of bridge frames.
A careful evaluation of the local
ductility demands and capacities is
recommended if project constraints make
it impractical to satisfy the stiffness
requirements as specified in Table 7.1.2-
1.

Figure C7.1.2-1 Balanced Stiffness Parameters

7.1.3 Balanced Frame Geometry C7.1.3

The ratio of fundamental periods of The consequences of unbalanced
vibration for adjacent frames in the frame geometry include a greater
longitudinal and transverse directions likelihood of out-of-phase response
shall satisfy: between adjacent frames leading to large
relative displacements that increase the
T probability of longitudinal unseating and
0.7 ≤ Ti ≤ 1.43 (7.1.3-1)
j pounding between frames at the
expansion joints. The pounding of
where: adjacent frames will transfer the seismic
Ti = natural period of frame i (sec) demand from one frame to another, which
Tj = natural period of frame j (sec) in combination with relative translation of
the frames, may exceed the stand-alone
capacity of the frame receiving the
additional seismic demand.
The techniques recommended in
C7.1.2 may also be used to satisfy
Equation 7.1.3-1.
7.2 SUPERSTRUCTURES
7.2.1 Girders
7.2.1.1 Effective Superstructure Width C7.2.1.1
The effective width of superstructure The effective width for open soffit
resisting longitudinal seismic moments, structures (e.g. T-Beams and I-Girders) is
Beff shall be taken as: reduced because they offer less
resistance to the torsional rotation of the
Dc + 2Ds Box girders and slab
superstructures
bent cap.
Beff = � Open soffit
If the effective width cannot
Dc + Ds superstructures accommodate enough steel to satisfy the
(7.2.1.1-1) overstrength requirements of Sections
4.4.2 and 4.4.3, the following actions may
where: be taken:
Dc = column cross sectional dimension • Thicken the soffit and/or deck
in the transverse direction. For slabs
flared columns, Dc shall be based • Increase the resisting section by
on the prismatic column section, widening the column
ignoring the flares • Haunch the superstructure
Ds = depth of superstructure at the bent
cap • Add additional columns
• Increase the structure depth

The effective superstructure width

may be increased for cross-sections away
from the bent cap by using a 45° spread
from the cap face until the full section
becomes effective, as shown in Figure
7.2.1.1-1 (A) and (B).
On skewed bridges, the effective width The method for determining the
shall be projected normal to the girders effective width for skewed bridges is
with one end of the width intersecting the illustrated in Figure C7.2.1.1-1.
bent face such that one half of the width
lies on either side of the column
centerline.

Figure 7.2.1.1-1 Effective Superstructure Width

Figure C7.2.1.1-1 Effective Superstructure Width for Skewed Bridge

Figure C7.2.1.1-1 Effective Superstructure Width for Skewed Bridge (continued)

7.2.1.2 Precast Girders C7.2.1.2

Multi-span precast (PC) girder bridges Precast girders made continuous for
located at sites with peak ground positive and negative moment continuity
acceleration (PGA) equal to or greater across supports are used in more
than 0.6g shall be provided with seismically active areas (PGA ≥ 0.6g) in
superstructure top and bottom steel at the order to reduce the risk of unseating and
supports to ensure continuity of to improve energy dissipation. As used
reinforcement in the longitudinal direction herein, “continuity of reinforcement”
and capacity protection of the includes reinforcement details across
superstructure, as shown in Figure superstructure-to-cap joints that emulate
7.2.1.2-1 (Type A and Type B). The a continuous cast-in-place (CIP) joint, as
bottom reinforcement shall be in the form illustrated in Figure 7.2.1.2-1 (Type A and
of prestressing strands, or mild steel, or Type B). Research (Werff et al., 2015) has
an equivalent combination of prestressing confirmed that precast girders with
strands and mild steel. A minimum of 4 to integral column-to-superstructure details
0.6-inch diameter prestressing strands, or effectively resist longitudinal seismic
4 - #8 mild steel bars, or equivalent mild demands. Type A connection is
steel and/or prestressing strands, shall be considered the most structurally robust.
provided in the girder bottom over the For Type C connections, the
supports. This bottom continuity assumption of girder continuity is only
reinforcement may also be used to satisfy valid for sites with PGA less than 0.6g.
the requirements of vertical acceleration, Designers should show an appropriate
as specified in Section 7.2.2. deck pour sequence to avoid excessive
For sites with peak ground negative moment at the joints which may
acceleration less than 0.6g, a pinned occur if bent cap joints are made integral
substructure-to-superstructure prior to pouring the deck. Alternatively,
connection with superstructure negative the joint may be designed to
moment continuity, as shown in Figure accommodate large negative moments
7.2.1.2-1 (Type C) may also be used. A from construction staging.
true pin that does not transmit moment The required reinforcement in the
across the substructure-to-superstructure girder bottom to resist positive moment is
joint shall be used for Type C connection. placed during casting of the precast
If the substructure is pinned to the girders. The required top reinforcement is
superstructure as shown in Figure positioned in the top slab and made
7.2.1.2-1 (Types B and C), the base of the integral at the bridge site. Strands
SCM shall be fixed. extended from PC girders cannot be used
Substructure-to-superstructure to meet negative seismic moment
connections with only negative moment demands.
continuity and without a true pin
connection, as illustrated in Figure
C7.2.1.2-1 (Type D), shall not be allowed.
Allowable precast girder seismic
connections are summarized in Table
7.2.1.2-1.

Table 7.2.1.2-1 Allowable Connection Historically, precast girders have often

Types for Precast Girders lacked a direct positive moment
connection at the bents. This connection
PGA Allowable Connection Type
configuration is illustrated as Type C
< 0.6g A, B, C (Figure 7.2.1.2-1) and Type D (Figure
≥ 0.6g A, B C7.2.1.2-1). However, Type C is allowed
in relatively low seismicity areas provided
no moments are transferred through the
pin connection. Type D connection is not
allowed in order to prevent possible
superstructure damage in seismic events.
(A1) (B1)
(A2) (B2)
• Superstructure pinned to top of
column or drop cap (Base of SCM
fixed)
• Superstructure positive and negative
moment continuity
• Top of column fixed to drop cap
(Figure B1)
(A3) Type B
• Substructure integral with
superstructure
• Superstructure positive and negative
moment continuity
Type A
Figure 7.2.1.2-1 Allowable Precast Girder-to-Substructure Connections

NOTES
1. All reinforcement and connection
details not shown.
2. Drop cap width may be different from
bent cap diaphragm width.
(C1)
(C2)
• Superstructure negative moment
continuity with a true pin connection
• Top of column fixed to drop cap
(Figure C1)
Type C (for PGA < 0.6g only)
Figure 7.2.1.2-1 Allowable Precast Girder-to-Substructure Connections (Continued)
• Superstructure negative moment

continuity only
Type D
Figure C7.2.1.2-1 Typical Historical
Precast Girder Connection
7.2.2 Reinforcement Requirements for C7.2.2

Vertical Acceleration
Multi-span girder bridges located at The intent of this provision is to ensure
sites with peak ground accelerations that all superstructure types have a
equal to or greater than 0.6g shall be nominal amount of reinforcement
designed for the effects of vertical ground available to resist the demands from any
excitation as specified herein. Moment vertical excitation. Mild steel is the
demands induced by a uniformly applied preferred reinforcement for vertical
vertical force equal to 25% of the dead acceleration because of its superior
load applied upward and downward as ductility over prestressing strands and
shown in Figure 7.2.2-1 shall not exceed should be used wherever there is enough
the nominal flexural capacity of the space to place the bars, such as the
superstructure based on the locations shown in Table 7.2.2-1. Due to
reinforcement types specified in Table space constraints in most precast girders,
7.2.2-1. The superstructure at seat type prestressing strands are allowed to be
abutments shall be modeled as pinned in used for vertical acceleration
the vertical direction. reinforcement as specified in Table 7.2.2-
The reinforcement used for vertical 1.
acceleration shall be evenly distributed The uniformly applied vertical force of
and may be used to satisfy the 25% of the dead load should not be
requirements for other load cases. Any combined with the superstructure dead
splice used shall be placed away from the load.
critical zones (mid-spans and near
supports) and shown on the plans.
The longitudinal side reinforcement in
the girder webs across the bent
cap/diaphragm shall consist of mild steel
capable of resisting 125% of the dead
load shear at the face of bent
cap/diaphragm by means of shear friction.
For CIP girders, the longitudinal side
reinforcement shall pass through the bent
cap diaphragm and extend into the girder
for a minimum of 1.5 Ds beyond the face
of the bent cap diaphragm. For precast
prestressed girders, the longitudinal side
reinforcement shall be embedded in the
girder a minimum distance of (Ds + Idb )
from the face of the diaphragm and
developed into the diaphragm, where Idb
is the basic tension development length,
as specified in Section 5 of AASHTO-CA
BDS.

Figure 7.2.2-1 Equivalent Static Vertical Loads and Moments on a Segment of

Superstructure for Vertical Acceleration
Table 7.2.2-1 Reinforcement Types for Vertical Acceleration
Girder Type
Loading Location
Cast-in-Place Precast
Downward- Midspan Mild steel and/or Prestressing strand

acting Bent Mild steel
Midspan Mild steel
Upward- Use provision for PC girder
acting Bent Mild steel bottom reinforcement at
supports in Section 7.2.1.2

7.2.3 Hinges
7.2.3.1 General C7.2.3.1
Polytetrafluoroethylene (PTFE) In general, service loads will be
spherical bearings shall be used at all in- greater than the seismic demands on in-
span bridge hinges. For seismic design, span hinges. Therefore, in-span hinges
PTFE spherical bearings shall be are typically designed for non-seismic
positioned as shown in Figure 7.2.3.2-1. loads and checked for the effects of
The bottom (i.e., supporting) corbel shall seismic loading.
be designed for maximum service loads. The hinge allows each frame to
Any changes in moment demand arising displace independently during an
from opening of the hinge shall be earthquake. Large relative displacements
considered in the design of the top (i.e., can develop if displacements of the bridge
supported) corbel. frames are out-of-phase. All frames
including balanced frames or frames with
small differences in mass and/or stiffness
will exhibit some out-of-phase response.
The objective of meeting the fundamental
period requirements between adjacent
frames is to prevent unbalanced loading
of one frame by the adjacent frame.
Locating expansion joints between
closely spaced adjacent bents such that
the superstructures on either side of the
joint are supported by cantilever beam
action only, requires approval through a
PSDC.
7.2.3.2 Support Length Requirements in C7.2.3.2

the Longitudinal Direction
The support length normal to the Sufficient support length should be
centerline of bearing, NH shall satisfy: available to accommodate the anticipated
MR + Δeq + Lmp thermal movement, prestress shortening,
1
creep, and shrinkage (i.e., Movement
NH ≥ � Ds (7.2.3.2-1) Range, MR), as well as the relative
3
30 in. longitudinal earthquake displacement
demand between adjacent frames. The
where:
total anticipated joint movement, MR is
NH = support length normal to the obtained from the Joint Movement
centerline of bearing (in.), as Calculation form.
shown in Figure 7.2.3.2-1 The intent of the support length
Lmp = length of masonry plate for the specified in Equation 7.2.3.2-1 is to
bearing (in.) ensure that the sliding surface of the sole
Δeq = relative longitudinal earthquake plate is in full contact with the concave
displacement demand based on plate of the bearing when the joint opens
Safety Evaluation Earthquake (in.) during the design seismic event.

Figure 7.2.3.2-1 Support Length Requirements at In-span Hinges
Δeq shall be obtained using either of The length of the bearing masonry
the following methods: plate is dependent on the load carried by
each bearing. Therefore, the designer
Method 1:
may adjust the support length by using an
Nonlinear Time History Analysis (NTHA)
appropriate number of bearings across
with elements that model gaps and impact
the hinge.
on gap closure, and
For bridges skewed at an angle, θ, the
Method 2: resulting support length measured along
Analysis methods other than NTHA the longitudinal axis of the bridge is
(NH ⁄cos θ).
Δeq = �(ΔD1 )2 + (ΔD2 )2 − 0.4ΔD1 ΔD2 Elastic Analysis, in general, cannot be
(7.2.3.2-2) used to determine the displacement or
force demands at the intermediate
where: expansion joints in multi-frame structures.
ΔD1 and ΔD2 = earthquake A more sophisticated analysis such as
displacement demands on either NTHA is required to capture relative
side of the hinge (in.) frame displacements (Δeq ). Hence
Method 1 is preferred over Method 2.

For Method 2, the equation for Δeq is

based on the results of a Caltrans’
sponsored research (Desroches and
Fenves, 1997) for the case of in-span
hinges without restrainers. Equation
7.2.3.2-2 differs from that used in SDC
Version 1.7 by the inclusion of a cross
correlation term. The coefficient of 0.4
used in the cross-correlation term was
obtained by assuming average values of
target displacement demand ductilities
and effective period ratios, (Ti ⁄Tj ) over
the allowable period ratios specified in
Section 7.1.3.
7.2.3.3 Shear Key Requirements in the C7.2.3.3

Transverse Direction
Shear keys shall be designed to Typically, hinges are expected to
transfer the shear between adjacent transmit the lateral shear forces
frames if the shear transfer mechanism is generated by small earthquakes and
included in the demand assessment. service loads. Determining the
Forces generated by any elastic earthquake force demand on shear keys
model shall not be used to design shear is difficult since the magnitude is
keys. The transverse shear demand at dependent on how much relative
the hinge shall be taken as the smaller of displacement occurs between the frames.
the sum of the overstrength shear EDA and ESA may predict force
demands of the columns in the bents demands on the shear keys that differ
adjacent to either side of the hinge. significantly from the actual forces.
The minimum transverse shear key The half-inch to three-quarter inch gap
shall be: provided around the shear keys is
• for multi-cell box girder vehicular intended to eliminate binding of the hinge
bridges - two 8 x 8 x 5/8 in. hollow under service operation and to ensure
structural steel sections (i.e., 2 - that lateral rotation will occur thereby
HSS 8x8x5/8) minimizing moment transfer across the
• for slab bridges, single-cell box expansion joint.
girder vehicular bridges, and Although large relative displacements
pedestrian bridges - two 5 x 5 x 1/2 are not anticipated for frames with similar
in. hollow structural steel sections periods exposed to synchronous ground
(i.e., 2 - HSS 5x5x1/2) motion, certain structural configurations
may be susceptible to lateral instability if
A half-inch to three-quarter inch gap the transverse shear keys completely fail.
shall be provided around the shear keys. Particularly susceptible are: skewed
Internal concrete keys shall not be bridges, bridges with three or less girders
used. and narrow bridges with significant
superelevation.

Hollow structural steel section used as

transverse shear keys will substantially
increase the shear transfer capacity
across expansion joints if significant out-
of-phase displacements are anticipated.
The shear capacity of the hollow
structural steel section may be
determined in accordance with the
provisions of Section 6 of Caltrans
Seismic Design Specifications for Steel
Bridges (Caltrans, 2016). Refer to Bridge
Standard Details XS7-085 for hinge
transverse shear key details for multi-cell
box girder vehicular bridges. For non-box
girder bridges, a special transverse shear
key detail is required.
7.2.3.4 Restrainers C7.2.3.4

Restrainers shall not be used to Hinge restrainers are not mandatory
reduce the required support length at but may be useful in reducing bridge
hinge seats in new bridges. Adequate damage and/or excessive movement
support length as specified in Section during small-to-moderate earthquakes.
7.2.3.2, shall be provided to prevent Restrainers are recommended in
unseating as a primary requirement. widenings where the existing bridge has
already been retrofitted with restrainers.
Design of restrainers should not be
based on the force demands predicted by
Elastic Dynamic Analysis (EDA). BDA 14-
1 provides an approximate method for
determining the size and number of
restrainers at expansion joints.
If the designer elects to use
restrainers, the following guidelines shall
be followed:
• A minimum of two restrainer units
are required at each hinge and
shall be symmetrically located at
the exterior bays. Where possible,
restrainer units shall be placed in
alternating cells.
• Restrainers shall be detailed to
allow for easy inspection and
replacement

• Restrainer layout shall be

symmetrical about the centerline of
the superstructure
• Restrainer systems shall
incorporate an adequate gap for
expansion, which shall be shown
on the Structure plans
• Permanent access openings for
the restrainers shall be provided
for inspection and repair
• Restrainers used in post-tensioned
superstructures shall not be
anchored prior to completion of the
pre-stressing operation.
Adequate lengths of cables or bars

should be used in order to assure
sufficient elongation capacity. Hinge
restrainer design should ensure that joint
movements are kept within acceptable
limits and restrainers work within the
elastic range. Insufficient elongation
ability can cause premature failure of the
restrainers while restrainers that are too
long may not prevent unseating.
When placing restrainers on new
structures with post-tensioned
superstructure spans, the engineer
should consider the shortening of the
spans.
Yield indicators are required on all
cable restrainers, as shown in Standard
Detail Sheet XS 7-090. Refer to Bridge
Standard Detail Sheets for drawings of
different types of cable restrainer units.
For material properties pertaining to
restrainer cables, refer to Federal
Specification RR-W-410 - Wire Rope and
Strand.

7.2.3.5 Pipe Seat Extenders C7.2.3.5

Pipes shall not be used as seat Pipe seat extenders may be used for
extenders in new bridges. seismic retrofit of bridges.
7.2.4 Superstructure Depth

The superstructure depth, Ds shall be
measured at the face of the bent cap and
shall be taken as specified in Table 7.2.4-
1.
Table 7.2.4-1 Depth of Superstructure
Superstructure Type Analysis Direction Superstructure Depth, Ds
Superstructure without Transverse Distance between top of deck

drop cap Longitudinal and superstructure soffit
Distance between top of deck

Transverse
Superstructure with and bottom of drop cap
drop cap Distance between top of deck
Longitudinal
and superstructure soffit
7.3 BENT CAPS

7.3.1 Integral Bent Caps C7.3.1
The effective width of integral bent Bent caps are considered integral if
caps for resisting flexural demands from they terminate at the outside of the
plastic hinging in SCMs shall be as exterior girder and respond monolithically
specified in Section 4 of AASHTO-CA with the girder system during dynamic
BDS. excitation.
Bent cap widths shall satisfy Equation
7.4.3-1.
7.3.2 Non-Integral Bent Caps

7.3.2.1 General C7.3.2.1
Non-integral caps shall satisfy all Non-integral bent caps may provide
requirements for frames in the transverse support for simply supported
direction. superstructure spans or continuous spans
with a separation detail such as an
elastomeric pad between the bent cap
and the superstructure.

7.3.2.2 Minimum Bent Cap Width C7.3.2.2

Non-integral caps supporting Continuity devices such as rigid
superstructures with expansion joints at restrainers or web plates may be used to
the cap shall have sufficient width to ensure that unseating does not occur but
prevent unseating of the superstructure. cannot be used in lieu of adequate bent
The support length for non-integral bent cap width.
caps shall satisfy Equation 7.2.3.2-1.
7.3.3 Bent Cap Depth C7.3.3

Bent cap depths shall be proportioned With the exception of slab bridges,
to meet the requirements of Sections every effort should be made to provide
7.6.2 and 8.3.1. enough cap depth to develop the
longitudinal reinforcement of SCMs
without using hooks or headed bars. Slab
bridge requirements are specified in
Section 9.
7.4 SUPERSTRUCTURE JOINTS

7.4.1 Joint Performance
Moment resisting connections
between the superstructure and the
column shall be designed to resist the
col
column overstrength demands, Mo and
col
Vo while remaining essentially elastic.
7.4.2 Joint Proportioning C7.4.2

All superstructure-to-column moment The principal stresses and forces
resisting joints shall be proportioned to acting on a superstructure-to-column joint
satisfy: are illustrated in Figure C7.4.2-1.
Principal tension:
pt ≤ 12�f 'c (7.4.2-1)
(In Equation 7.4.2-1, f 'c and pt have units

of psi)
Principal compression: The limit of pc ≤ 0.25 f 'c is based on
the need to prevent diagonal crushing of
pc ≤ 0.25 f 'c (7.4.2-2) the joint core concrete. As a result of
diagonal cracks induced by cyclically
in which: acting earthquake forces and the tensile
strains in the joint shear reinforcement,
concrete compressive strength is reduced
(Priestley et al., 1996).
A negative result from Equation 7.4.2-

�fh +fv � f −fv 2 3 signifies that the joint has nominal
pt = − �� h 2 � + v2jv (7.4.2-3)
2 principal tensile stresses.
Unless the prestressing is specifically
designed to provide horizontal joint
�fh +fv �
� fh −fv 2 compression, fh can typically be ignored
pc = − � 2 � + v2jv (7.4.2-4)
2 without significantly affecting the principal
stress calculation.
P
fh = B bD (7.4.2-5)
cap s
P
fv = A c (7.4.2-6)
jh
T
vjv = A c (7.4.2-7)
jh
Ajh = (Dc + Ds )Bcap (7.4.2-8)
Ajv = Iac,provided �Bcap � (7.4.2-9) Equation 7.4.2-9 defines the effective

joint area in terms of the bent cap width
where: regardless of the direction of bending.
This simplified definition of Ajv may
Ajh = effective horizontal joint area
conservatively underestimate the
Ajv = effective vertical joint area
effective joint area for SCMs with large
Bcap = bent cap width cross section aspect ratios, in longitudinal
Iac,provided = actual length of column bending.
longitudinal reinforcement
embedded into the bent cap
Pb = beam axial force (including
prestressing) at the center of the
joint
Tc = column tensile force defined as
col
Mo /h, where h is the distance
from c.g. of tensile force to c.g. of
compressive force on the section.
Alternatively, Tc may be obtained
from the moment-curvature
analysis of the cross section.
For slab bridges, Ajh and Ajv shall be

determined in accordance with Section
9.5.

Figure C7.4.2-1 Joint Shear Stresses in T Joints
7.4.3 Minimum Bent Cap Width C7.4.3

The minimum bent cap width required Larger cap widths may be required to
for adequate joint shear transfer shall be accommodate joint shear reinforcement.
taken as:
Bcap = Dc + 24 (7.4.3-1)
where:
Bcap = bent cap width (in.)
Dc = diameter or cross section
dimension of column in the
direction of the cap width (in.)

7.4.4 Types of Joint

7.4.4.1 “T” Joints
The following types of joints shall be
classified as “T” joints for joint shear
analysis:
• Interior joints of multi-column bents
in the transverse direction
• All integral column/superstructure
joints in the longitudinal direction
• Exterior column joints for box
girder superstructures if cap beam
longitudinal reinforcement is fully
developed beyond the exterior
face of the column.
7.4.4.2 Knee Joints C7.4.4.2

An exterior column-to-superstructure Knee joints differ from T joints
joint shall be classified as a Knee joint if it because the joint response varies with the
satisfies: direction of the moment (opening or
closing) applied to the joint, as shown in
S < Dc (7.4.4.2-1) Figure C7.4.4.2-1. Therefore, knee joints
are evaluated for both opening and
where: closing failure modes.
S = cap beam short stub length. S is In the opening moment case, a series
equal to the distance from the of arch-shaped cracks tends to form
exterior girder edge at soffit to the between the compression zones at the
face of column measured along the outside of the column and top of the
bent centerline as shown in Figure beam. The intersection of the arch strut
7.4.4.2-1. and the flexural compression zones at the
top of the beam and the back of the
For joint shear reinforcement design, column create outward-acting resultant
knee joints shall be identified as: forces. If the beam bottom reinforcement
is anchored only by straight bar
Case 1:
1
S < 2 Dc (7.4.4.2-2) extension, there will virtually be no
resistance to the horizontal resultant
1 tensile force. It will cause vertical splitting,
Case 2: 2
Dc ≤ S < Dc (7.4.4.2-3) reducing competence of the anchorage of
the outer column rebars and beam top
rebars (Priestley et al., 1996).

In the closing moment case, a fan–

shaped pattern of cracks develops,
radiating from the outer surfaces of beam
and column toward the inside corner. If
there is no vertical reinforcement
clamping the beam top reinforcement into
the joint, the entire beam tension, Tb is
transferred to the back of the joint as there
isn’t an effective mechanism to resist the
moment at the base of the wedge-shaped
concrete elements caused by bond-
induced tension transfer to the concrete
(Priestley et al., 1996).
It may be desirable to pin the top of the
column to avoid moment transfer through
a knee joint. However, the benefits of a
pinned joint should be weighed against
increased foundation demands and the
effect on the frame’s overall performance.
Figure 7.4.4.2-1 Knee Joint Parameters

Cb = beam compressive force, Cc = column compressive force, Tb = beam tensile force,

Tc = column tensile force, Mb = beam moment, Mc = column moment
Figure C7.4.4.2-1 Knee Joint Failure Modes
7.4.5 Joint Shear Reinforcement

7.4.5.1Minimum Joint Shear C7.4.5.1
Reinforcement Minimum joint shear reinforcement
The minimum volumetric ratio of may be provided in the form of column
transverse column reinforcement, ρs,min transverse steel continued into the bent
continued into the bent cap shall be taken cap.
as:
3.5�f 'c
ρs,min = (7.4.5.1-1)
fyh
where:
f 'c = specified compressive strength of
unconfined concrete (psi)
fyh = specified minimum yield strength
of transverse reinforcement (psi)

Where the principal tension stress, pt

is greater than 3.5�f 'c , the joint shear
reinforcement specified in Sections
7.4.5.2 (for T joints), 7.4.5.3 (for Knee
joints), or 9.5 (for slab bridges) shall be
provided.
Where pt ≤ 3.5�f 'c, only the minimum
joint shear reinforcement shall be
provided.
7.4.5.2 T Joint Shear Reinforcement C7.4.5.2

A) Vertical Stirrups: Figures 7.4.5.2-2, 7.4.5.2-3 and
7.4.5.2-4 illustrate the location of joint
Vertical joint shear reinforcement, Asjv shear reinforcement.
shall satisfy:
jv
As ≥ 0.2 Ast (7.4.5.2-1) Asjv may be used to meet other
requirements documented elsewhere
where: including the shear in the bent cap.
Asjv = area of vertical joint shear
reinforcement
Ast = total area of column longitudinal
reinforcement anchored in the joint
(in.2)
Vertical stirrups shall be placed

transversely within a distance Dc
extending from either side of the column
centerline. The vertical stirrups, Asjv shall
be placed on each side of the column as
shown in Figures 7.4.5.2-1, 7.4.5.2-2 and
7.4.5.2-4. The stirrups provided in the
overlapping areas in Figure 7.4.5.2-1
shall count towards meeting the
requirements of both areas creating the
overlap.

Single-Column Bent
Multi-Column Bent
Figure 7.4.5.2-1 Location of Vertical Joint Reinforcement (Plan View of Bridge)

Bent Cap Details, Section at Column for Bridges with 0 to 20° Skew
(Detail applies to sections within 2 x Diameter of SCM, centered about centerline of SCM).
(Detail applies to T-Beam and Box Girder Bridges where deck reinforcement is placed parallel to Cap)
Figure 7.4.5.2-2 Joint Shear Reinforcement Details

Figure 7.4.5.2-3 Location of Horizontal Joint Shear Reinforcement

Bent Cap Details, Section at Column for Bridges with Skew Larger than 20°
(Detail applies to sections within 2 x Diameter of SCM, centered about CL of SCM).
(Detail applies to T-Beam and Box Girder Bridges where deck reinforcement is placed normal or radial to CL
Bridge)
Figure 7.4.5.2-4 Joint Shear Reinforcement Details for Skewed Bridges

B) Horizontal Stirrups:
jh
Horizontal stirrups or ties, As shall
satisfy:
jh
As ≥ 0.1Ast (7.4.5.2-2)
where:
jh
As = area of horizontal stirrups or ties
The horizontal stirrups or ties shall be

placed transversely around the vertical
stirrups or ties in two or more intermediate
layers spaced vertically at not more than
jh
18 inches. As shall be placed within the
distance Dc extending from either side of
the column centerline, as shown in Figure
7.4.5.2-3.
C) Horizontal Side Reinforcement:

The total longitudinal side face
sf
reinforcement in the bent cap, As shall
satisfy:
top
sf 0.1Acap sf
As ≥ max � bot
(7.4.5.2-3) Fifty percent of As is placed on each
0.1Acap of the two side faces.
where:
top
Acap = area of top flexural steel (in.2)
bot
Acap = area of bottom flexural steel (in.2)
sf
As shall be placed near the side faces
of the bent cap with a maximum spacing
of 12 inches, as shown in Figures 7.4.5.2-
2 and 7.4.5.2-4. Any side reinforcement
placed to meet other requirements shall
count towards meeting the requirement
sf
for As .

D) J-Dowels:
For bents skewed more than 20°, J-
dowels shall be provided. The J-dowel
reinforcement, Asj-bar shall satisfy:
j-bar
As ≥ 0.08Ast (7.4.5.2-4)
The J-dowels shall be hooked (with a

135° or greater hook) around the
longitudinal top deck steel and extend
alternately 24 inches and 30 inches into
the bent cap.
The J-dowels shall be placed within a
rectangular region defined by the width of
the bent cap and the distance Dc on either
side of the centerline of the SCM, as
shown in Figures 7.4.5.2-3 and 7.4.5.2-4.
E) Transverse Reinforcement:
Transverse reinforcement for the SCM The transverse reinforcement for the
extended into the bent cap shall consist of SCM extended into the bent cap may be
hoops. The volumetric ratio of the hoops, used to satisfy this reinforcement
ρTs shall satisfy: requirement.
4A Ast
ρTs = D' b ≥ 0.4 � 2 � (7.4.5.2-5)
s l ac,provided
For interlocking cores, ρTs shall be

based on the area of reinforcement, Ast of
each core.
F) Anchorage for SCM Main

Reinforcement:
The longitudinal reinforcement of
SCMs shall extend into the cap beam as
specified in Section 8.3.1.1 to fully
develop the compression strut
mechanism in the joint.

7.4.5.3 Knee Joint Shear Reinforcement C7.4.5.3

The main bent cap top and bottom Knee joint shear reinforcement details
bars shall be fully developed from the for straight (0 - 20° skew) and skewed (>
inside face of the SCM and shall extend 20° skew) bridge configurations are
as closely as possible to the outside face similar to those shown in Figures 7.4.5.2-
of the bent cap, as shown in Figure 2 and 7.4.5.2-4, respectively.
7.4.4.2-1.
A) Bent Cap Top and Bottom Flexural

Reinforcement (For Cases 1 and 2 Knee
Joint):
Top and bottom reinforcement in the The U bars may be combined with
form of continuous “U” bars, As
u-bar
shall be bent cap main top and bottom
provided within the bent cap width, as reinforcement using mechanical couplers.
illustrated in Figures 7.4.5.3-2 to 7.4.5.3-
u-bar
4. The area of As shall satisfy:
u-bar
As ≥ 0.33Ast (7.4.5.3-1)
where:
Ast = area of column longitudinal
(in.2)
Splices in the U bars shall not be

located within a distance, ld from the
interior face of the column.
B) Vertical Stirrups (For Cases 1 and 2

Knee Joint):
Vertical stirrups or ties, Asjv shall be See also Figure 7.4.5.3-5 for
placed transversely within each of regions illustration of rebar placement.
1, 2, and 3 of Figure 7.4.5.3-1. The
required area of Asjv shall satisfy:
Asjv ≥ 0.2Ast (7.4.5.3-2)
The stirrups provided in the

overlapping areas of Figure 7.4.5.3-1
shall count towards meeting the
requirements of both areas creating the
overlap. Asjv may be used to meet other
requirements documented elsewhere
including shear in the bent cap.

Figure 7.4.5.3-1 Location of Knee Joint Vertical Shear Reinforcement (Plan View)
C) Horizontal Stirrups (For Cases 1 and

2 Knee Joint):
jh
Horizontal stirrups or ties, As shall be
placed transversely around the vertical
stirrups or ties in two or more intermediate
layers spaced vertically at not more than
18 inches, as illustrated in Figure 7.4.5.3-
jh
5. The required area of As shall satisfy:
jh
As ≥ 0.1Ast (7.4.5.3-3)
The horizontal stirrups or ties shall be

placed within the limits shown in Figures
7.4.5.3-2 and 7.4.5.3-3.

D) Horizontal Side Reinforcement (For

Cases 1 and 2 Knee Joint):
Longitudinal side face reinforcement,
sf
As shall be placed near the side faces of
the bent cap with a maximum spacing of
sf
12 inches. The required area of As shall
satisfy:
top
sf 0.1Acap
As ≥ max � bot
(7.4.5.3-4)
0.1Acap
where:
top
Acap = area of top flexural steel (in.2)
bot
Acap = area of bottom flexural steel (in.2)
The side reinforcement shall be in the

form of “U” bars and shall be continuous
over the exterior face of the Knee Joint.
Splices in the U bars shall be located at
least a distance ld from the interior face of
the column. Any side reinforcement
placed to meet other requirements shall
count towards meeting this requirement.
E) Horizontal Cap End Ties (For Case 1

Knee Joint Only):
Horizontal ties, Asjhc shall be placed at
the end of the bent cap, as shown in
Figures 7.4.5.3-2, 7.4.5.3-3, and 7.4.5.3-
5. The required area of Asjhc shall satisfy:
Asjhc ≥ 0.33As
u-bar
(7.4.5.3-5)
Horizontal ties shall be placed around

the intersection of the bent cap horizontal
side reinforcement and the continuous
bent cap U bar reinforcement and spaced
at not more than 12 inches vertically and
horizontally. The horizontal reinforcement
shall extend through the column cage to
the interior face of the column.

F) J-Dowels (For Cases 1 and 2 Knee

Joint):
For bents skewed more than 20°, “J”
bars (dowels) shall be provided, as shown
in Figures 7.4.5.3-3, and 7.4.5.3-4. The
j-bar
area of As shall satisfy:
j-bar
As ≥ 0.08Ast (7.4.5.3-6)
The “J” bars shall be hooked around

the longitudinal top deck steel with at
least a 135° hook and extend
alternately 24 inches and 30 inches into
the bent cap.
The J dowels shall be placed within
a rectangular region defined by the
bent cap width and the limits shown in
Figure 7.4.5.3-3.

NOTE:
Flaring the inside face of exterior girders may be required for cast-in-place post-tensioned
box girder construction in order to meet clearance requirements for ducts and U-bar
reinforcement. To accommodate other girder and bent cap situations, it may be necessary
to adjust rebar positions while ensuring required concrete covers are met.
Figure 7.4.5.3-2 Knee Joint Shear Reinforcement - Skew ≤ 20°

NOTE:
Flaring the inside face of exterior girders may be required for cast-in-place post-tensioned
box girder construction in order to meet clearance requirements for ducts and U-bar
reinforcement. To accommodate other girder and bent cap situations, it may be necessary
to adjust rebar positions while ensuring required concrete covers are met.
Figure 7.4.5.3-3 Knee Joint Shear Reinforcement - Skew > 20°

G) Transverse Reinforcement:
Transverse reinforcement in the joint The transverse reinforcement for the
region shall consist of hoops. The SCM extended into the bent cap may be
volumetric ratio of the transverse used to satisfy this requirement.
reinforcement, ρsknee shall satisfy:
• For Case 1 Knee joint In Equations 7.4.5.3-7 to 7.4.5.3-9, the
volumetric ratio of transverse
0.76Ast reinforcement, ρs knee
is as defined in
ρsknee = 2 (7.4.5.3-7)
Dc lac,provided Section C5.3.8.2.
• For Case 2 Knee joint, Integral

bent cap
Ast
ρsknee = 0.4 × 2 (7.4.5.3-8)
lac,provided
• For Case 2 Knee joint, Non-

integral bent cap
Ast
ρsknee = 0.6 × 2 (7.4.5.3-9)
lac,provided
For interlocking cores, ρsknee shall be

calculated on the basis of Ast and Dc of
each core (for Case 1 knee joints) and on
area of reinforcement Ast of each core (for
Case 2 knee joints).
All vertical column bars shall be
extended as closely as possible to the top
bent cap reinforcement.

Notes:
1) See Figure 7.4.5.3-5 for 3-D representation of other knee joint shear bars not shown
2) Not all bars shown for each bar type
3) Column transverse and longitudinal reinforcement extended into bent cap not
shown for clarity
Figure 7.4.5.3-4: 3-D Representation of Knee Joint Shear Reinforcement

u-bar j-bar sf
(As ,As , As )

Notes:
1) See Figure 7.4.5.3-4 for 3-D representation of other knee joint shear bars not shown
2) Not all bars shown for each bar type
3) Column transverse and longitudinal reinforcement extended into bent cap not
shown for clarity
Figure 7.4.5.3-5: 3-D Representation of Knee Joint Shear Reinforcement

jv jh jhc sf
(As ,As ,As , As )

7.5 BEARINGS AND EXPANSION JOINTS

7.5.1 Bearings C7.5.1
Polytetrafluoroethylene (PTFE) Typically, elastomeric bearings are
spherical bearings shall be used at all in- considered sacrificial elements while
span bridge hinges. PTFE spherical bearings are capacity
Bearings shall be checked to ensure protected elements. Bearings should be
that their displacement capacity and detailed so that they can be easily
mode of failure are consistent with the inspected for damage and replaced or
assumptions made in the seismic repaired after an earthquake.
analysis. It is preferable to use as many
bearings as possible in order to ensure a
balanced distribution of load across the
hinge and reduce the load transmitted to
each bearing.
Elastomeric and PTFE spherical
bearings are permitted by the SDC
without recourse to the PSDC procedure.
Any of these bearing types can be used at
bridge abutments because of the ease in
replacing bearings at abutments.
However, only PTFE spherical bearings
are to be used at in-span hinges because
of the difficulty in replacing bearings at in-
span hinges. PTFE spherical bearings
have relatively large displacement
capacities and last longer than
elastomeric bearings. PTFE spherical
bearings are not susceptible to edge
stress issues because rotation occurs
along the spherical surface.
Elastomeric Bearings
The lateral shear capacity of
elastomeric bearing pads is controlled by
either the dynamic friction capacity
between the pad and the bearing seat or
the shear strain capacity of the pad. The
dynamic coefficient of friction between
concrete and neoprene may be taken as
0.40 while that between neoprene and
steel may be taken as 0.35. The
maximum shear strain resisted by
elastomeric pads prior to failure is
estimated at ±150%.

Sliding Bearings
PTFE spherical bearings utilize low
friction PTFE sheet resin. Typical friction
coefficients for these bearings vary from
0.04 to 0.08. The friction coefficient is
dependent on contact pressure,
temperature, sliding speed, and the
number of sliding cycles. Friction values
may be as much as 0.12 at sliding speeds
anticipated under seismic loads.
A common mode of failure for sliding
bearings under moderate earthquakes
occurs when the PTFE surface slides
beyond the limits of the sole plate often
damaging the PTFE surface. The sole
plate should be extended to eliminate this
mode of failure whenever possible.
Seismic Isolation Bearings

Seismic isolation bearings are
nonstandard bridge features and their use
is subject to the PSDC procedure.
Information on seismic isolation bearings
is available in the draft MTD 20-22:
Seismic Design of Ordinary Bridges with
Isolation Bearings.
7.5.2 Seismic Expansion Joints C7.5.2

Recovery bridges shall be designed In contrast to seismic joints,
with seismic expansion joints. Seismic conventional bridge joints are not
joints shall accommodate the required designed for seismic loads and can only
horizontal movements and rotations while accommodate longitudinal and very
maintaining their full functionality with little limited transverse movement of the bridge
or no damage under the Functional deck, typically less than one inch.
Evaluation Earthquake (FEE). Conventional joints are expected to be
damaged and replaced after a seismic
event. Examples of seismic joints are the
plate joint seal assemblies shown in XS
sheets XS8-070 through XS8-100. Plate
joint seal assemblies are capable of
accommodating relatively large joint
openings, thereby preventing traffic
disruption even after a major seismic
event.

Seismic joints may also be used for

ordinary bridges with the following
characteristics:
• Skew greater than or equal to 35
degrees
• Curved bridges when the joint
transverse movement under
service conditions is greater than 1
inch and no shear keys prevent
such movement
• Bridges that cross fault lines or
located in areas with tectonic
movements
• Where bridge joints are required to
maintain their functionality with
little or no damage after a seismic
event
7.6 COLUMNS
The longitudinal reinforcement for all In structures with drop bent caps,
columns with circular and square cross- pinning the base of the columns is not
sections shall be arranged in a circular recommended unless the designer can
array. ensure that there is adequate framing
The longitudinal reinforcement for action between the bent cap and the
rectangular and oblong columns shall be superstructure to ensure longitudinal
arranged in an interlocking circular array. stability of the bridge.
Columns in single column bents Columns supporting outrigger bents
should be analyzed, designed, and are an exception and are designed as
detailed as fixed at both column ends. fixed at the base and pinned at the top.
In general, columns in a multi-column Typically, columns supported on Type
bent that is monolithic with the I and II shafts are considered as fixed at
superstructure should be designed as the base.
fixed at the top and pinned at the pile cap Pinning the base of columns leads to
or footing. However, multi-column bents a reduction in the foundation size and
pinned to the superstructure shall be fixed foundation costs. In comparison to a fixed
at the pile caps or footings. base column, a pinned base column
results in a softer structure leading to
larger drifts (lateral displacement)
particularly under seismic demands. Also,
pinning the base may increase the
moments at the top of columns under
strength and service load combinations
compared to those in a fixed-fixed
column. Consequently, pinned columns

may be subjected to higher moment

magnification factors. The combined
effects of increased moments at the fixed
end and the moment magnification may
lead to an increase in a column’s
longitudinal reinforcement.
Column design for seismic, strength,
and service limit states may result in a
dense reinforcement arrangement with
consequent construction-related
difficulties. If the column reinforcement
exceeds acceptable limits, one or a
combination of the following alternatives
may be used to achieve adequate column
design and bridge performance:
• Examine reinforcement
configuration
• Increase the number of columns
per bent
• Use oblong columns
• Use larger columns in multi-
column bents
• Shorten span lengths and add
bents
• Use higher strength concrete for
columns
• Use pile shafts in lieu of footings
• Incorporate foundation flexibility in
modeling and analysis
• Increase the elastic length of
shorter columns
• Use lightweight concrete
superstructure
• Add hinges in the superstructure
of long prestressed structures
• Use 3-D analysis instead of
Cantilever analysis to achieve
more realistic load distribution and
reduce P-Δ effects on single
column bents

7.6.2 Column Dimensions C7.6.2

The diameter of circular columns, Dc The relationship between column
shall be proportioned relative to the cross section dimension, Dc and bent cap
superstructure depth at the bent cap, Ds depth, Ds and between Dc and footing
and the footing depth, Dftg to satisfy: depth, Dftg are based on engineering
design experience.
Dc Every effort should be made to limit
0.7 ≤ ≤ 1.0 (Sup without drop cap)
Ds the column cross sectional dimensions to
�
Dc the depth of the superstructure. If the
≤ 1.0 (Sup with drop cap)
Ds column dimensions exceed the depth of
(7.6.2-1) the bent cap it may be difficult to meet the
joint shear requirements as specified in
Dftg
0.7 ≤ D (7.6.2-2) Section 7.4.2, and the superstructure
c capacity requirements as specified in
Section 5.4.4. Pinning the top of columns
If a reduced column section is used at
or using a reduced column section may
the column-to-superstructure or column-
be a viable alternative in these cases.
to-footing connection, Dc shall be taken
as the diameter of the reduced column
section.
7.6.3 Column Flares

7.6.3.1 Horizontally Isolated Column C7.6.3.1
Flares
The top of flared column sections shall Isolating the flare from the
be horizontally isolated from the soffit of superstructure/cap beam soffit, as shown
the bent cap. in Figure C7.6.3.1-1, allows the flexural
The horizontal gap isolating the flare hinge to form at the top of the flare,
from the bent cap shall extend over the minimizing the seismic shear demand on
entire cross section of the flare excluding the column. The added mass and
a core region equivalent to the prismatic stiffness of the isolated flare typically can
column cross section. be ignored in the dynamic analysis.
The flare gap shall be large enough so The horizontal flare isolation detail is
that it will not close during a seismic easier to construct than a combined
event. The minimum gap thickness shall horizontal and vertical isolation detail and
be 4 inches. is preferred wherever possible.
The gap thickness, G shall be based
on the estimated ductility demand and
corresponding plastic hinge rotation
capacity.

Figure C7.6.3.1-1 Horizontal Flare

Isolation
7.6.3.2 Vertical Flare Isolation C7.6.3.2

Vertical flare isolation may be used in Vertical flare isolation is illustrated in
combination with horizontal isolation if the Figure C7.6.3.2-1
plastic hinge rotation (based on the
equivalent plastic hinge length for
horizontally-isolated flared columns as
specified in Section 5.3.4) provides
insufficient column displacement
capacity.
Figure C7.6.3.2-1 Vertical Flare

Isolation

7.6.3.3 Lightly Reinforced Integral Flares C7.6.3.3

Lightly reinforced integral flares shall Column flares that are integrally
only be used when required for service connected to the bent cap soffit should be
load design or aesthetic considerations avoided. Test results have shown that
and the peak ground acceleration is less slender lightly reinforced flares perform
than 0.5g. The flare geometry shall be adequately after cracking has developed
kept as slender as possible. in the flare concrete, essentially
The column section at the base of the separating the flare from the confined
flare shall have adequate capacity to column core. However, integral flares
ensure that the plastic hinge will form at require higher shear forces and moments
the top of the flare. Higher plastic hinging to form the plastic hinge at the top of the
forces resulting from an integrally column compared to isolated flares.
connected, lightly reinforced flare shall be
considered in the design of the column,
superstructure, and footing.
7.6.3.4 Flare Reinforcement C7.6.3.4

Column flares shall be nominally Refer to Attachment 1 of MTD 6-1 for
reinforced outside the confined column flare reinforcement details.
core to prevent the flare concrete from
completely separating from the column at
high ductility demands.
Splicing of transverse flare Refer to Section C8.2.1 for additional
reinforcement shall satisfy the information on rebar splicing.
requirements of “service splice.” The
splice location shall be shown on the
Plans.
7.6.4 Column Key Design C7.6.4

Shear keys in pinned column
connections shall be designed for the
axial and shear forces associated with the
col
column’s overstrength moment, Mo
including the effects of overturning.
The area of interface shear key The key reinforcement shall be
reinforcement, Ask shall be taken as: located as close to the center of the
• If P is compressive: column as possible to minimize
developing a force couple within the key
1.2�Vocol − 0.25P�
reinforcement.
Ask = (7.6.4-1)
fy Equations 7.6.4-1 and 7.6.4-2 assume
the use of normal weight concrete placed
• If P is tensile: against a clean and intentionally
1.2�Vocol + P� roughened concrete surface.
Ask = (7.6.4-2)
fy

where:
P = absolute value of the net axial
force normal to the shear plane
(kip). P shall be equal to the lowest
axial load if compressive or
greatest axial load if tensile,
considering the effects of
overturning.
The area of dowel reinforcement In reality, most devices used to

provided in the pinned connection to provide a pinned connection between the
satisfy the column key design shall be column end and the footing/cap beam will
greater than or equal to 4 in.2. generate some moment which, if not
Any moment generated by the key accounted for in the design, may lead to
steel shall be considered in the design. unintended plastic hinging in the adjacent
The designer shall indicate on the capacity protected member.
plans that the receiving concrete surface Concrete-filled steel pipe or solid bar
for the pin shall be intentionally sections may be used in lieu of reinforcing
roughened to an amplitude of 0.25 in. steel to relieve congestion and reduce the
The pin connection shall be moment generated within the key.
proportioned such that the area of However, for columns in net tension,
concrete engaged in interface shear additional means should be employed to
transfer, Acv satisfies: address uplift.
Corrosion of the pin device should be
col considered.
4Vo
Acv ≥ � f 'c (7.6.4-3)
col
0.67Vo
The area of concrete section used in

the pin shall satisfy the axial resistance
requirements as specified in Section 5 of
AASHTO-CA BDS based on the column
with the greatest axial load and a
resistance factor Φ of 1.0.
Adequate thickness of the expansion
joint filler shall be provided around the
column shear key to accommodate the
maximum column rotation during a
seismic event without crushing the edge
of the column concrete against the
capacity protected member.

This page is intentionally left blank.

SECTION 8: SEISMIC DETAILING 8-1
SECTION 8
SEISMIC DETAILING
8.1 GENERAL C8.1

This Section provides the seismic This section is intended to provide
requirements for splices, transverse specifications on aspects of detailing that
reinforcement, and development of main are most relevant to the efficient seismic
flexural/longitudinal REINFORCING performance of bridges. Other aspects of
STEEL. These requirements shall apply structural detailing are covered in other
to both cast-in-place and precast Caltrans documents.
members.
8.2 SPLICES IN REINFORCING STEEL

Reinforcing bar splices shall be either: Specifications for splicing bar
"Ultimate Butt", "Service", or "Lap" as reinforcement are provided in the
specified in Table 8.2.1-1. Locations of Standard Specifications (Caltrans, 2015).
splices shall be clearly shown on the Additional information on lap splices is
plans. available in BDD 13-16.
If a project includes Ultimate Butt
splice and/or Service splice, the Design
Engineer shall convey this information to
the Specifications Engineer through a
"Memorandum to Specifications Engineer
and Estimator."
8.2.2 Reinforcement Splices in

Seismic Critical Members
8.2.2.1 No-Splice Zones C8.2.2.1
The “No-Splice Zones” for SCMs shall The No-Splice Zone in seismic critical
correspond to the plastic hinge regions members may be shown on the plans
specified in Section 5.3.2. No-Splice either as a fixed dimension or as a fraction
Zones shall be clearly identified on the of the height or length of the member.
plans.
Except as specified herein, splicing of
main flexural reinforcement shall not be
permitted in No-Splice Zones.

Table 8.2.1-1 Splice Requirements for Main Longitudinal Reinforcement
Member Location Splice Type
Not allowed, except as

Inside plastic hinge region
specified in Section 8.2.2.1
All SCMs
Outside plastic hinge
Ultimate butt
region
Top 20 ft Not allowed
Type II Shaft
Elsewhere Service
Piles within pile groups in
Everywhere Lap
class S1 soil
Bent Caps, Footings, and Inside Critical Zone*1 Not allowed
Pile Caps Outside Critical Zone*1 Service
Inside Critical Zone*1 Not allowed
Superstructures
Outside Critical Zone*1 Service or Lap*2
*1 Critical zones for capacity protected members shall be taken as locations where the
moment demand is greater than 75% of the maximum moment demand in the member.
*2 Service splice shall be used for reinforcement provided for longitudinal pushover
analysis. Lap splice shall not be used to splice this reinforcement.
Splicing of main flexural reinforcement For relatively long SCMs, the longest
in No-splice zones may be permitted for commercially available reinforcing steel
relatively long SCMs where the length of length should be used to ensure that
commercially available reinforcing steel is splicing within the No-splice zone is
inadequate to span the plastic hinge avoided or minimized. The allowable
region. The length of commercially splice zone is the portion of the SCM
available reinforcing steel shall not be outside the plastic hinge region.
taken less than 60 ft.
The transverse reinforcement shall
have the same area and spacing
throughout the required length of No-
Splice Zone.
8.2.2.2 Longitudinal Reinforcement

Splicing of main flexural reinforcement
outside the No-Splice Zone shall meet the
ultimate butt splice performance
requirements as specified in Table 8.2.1-
1.

Splicing of main flexural reinforcement

shall not be allowed if the flexural
reinforcement in the SCM can be placed
with a single length of commercially
available reinforcing bar.
8.2.2.3 Hoop Splices and Spiral C8.2.2.3

Terminations
Transverse reinforcement in SCMs Butt-splicing is achieved by the use of
shall be either ultimate butt-spliced hoops either welding or mechanical couplers.
or continuous spiral as specified in Table The "No Splice Zone" for spiral
8.2.2.3-1. Transverse reinforcement shall reinforcement means that spiral
be used over the entire length of the reinforcement termination is not allowed
seismic critical member. at any other location in the plastic hinge
When spiral reinforcement is used, the region other than at the SCM-to-soffit and
plastic hinge region shall be designated SCM-to-footing interfaces.
as the "No Splice Zone" for spiral Spiral reinforcement is generally
reinforcement. discontinued at the SCM-to-soffit
Spiral reinforcement at SCM-to-soffit interface to facilitate placement of main
and SCM-to-footing interfaces shall bars in the cap beam and is restarted just
terminate in and begin with a “Special above the soffit bars. Similarly, the spiral
Hook” as shown in Figure 8.2.2.3-1 reinforcement may be discontinued at the
(Spiral Termination Type 1). The pitch of SCM-to-footing interface. Since the spiral
the spiral reinforcement at these locations reinforcement is subjected to high strains
shall be less than or equal to half the pitch at these locations of a SCM, a special
of the spiral at a typical section. Special hook is required.
spiral hooks shall be shown on the plans. The spiral reinforcement at the ends of
For SCMs requiring spiral SCM rebar cages is subjected to relatively
reinforcement longer than is available in a lower levels of strain.
continuous roll, the spiral shall terminate A Special Hook, also referred to as
and restart outside the plastic hinge Spiral Termination Type 1, as shown in
region with spiral Termination Type 1. Figure 8.2.2.3-1, is obtained by making an
Spiral reinforcement at the ends of extra turn in the spiral coil in addition to a
SCM rebar cages shall terminate with tail equal in length to the diameter of the
either Termination Type 1 or 2 as shown rebar cage and passing through the core
in Figure 8.2.2.3-1. The termination detail of the SCM.
shall be shown on the plans.

Table 8.2.2.3-1 Applicability of Transverse Reinforcement in Seismic Critical

Members
Transverse Reinforcement
SCM
Hoops Spiral
Required
Column Not allowed
(Ultimate butt splice)
Type I shafts, Pile/Shaft Allowed when rebar cage
Allowed when rebar cage
group in class S2 soil, diameter ≥ 14 in.
diameter < 30 in.
and Pile extensions (Ultimate butt splice)
Spiral Anchor 90° Hook Detail Spiral Anchor 135° Hook Detail
(A) Spiral Termination Type 1 (B) Spiral Termination Type 2
Notes:
1) Hooks for spiral termination detail shall line up so as not to interfere with construction
operation.
2) Inspection tubes are not shown
Figure 8.2.2.3-1 Spiral Termination Details

8.2.3 Reinforcement Splices in

Capacity Protected Members
8.2.3.1 General
Reinforcing steel splices in capacity
protected members shall meet the
requirements specified in Table 8.2.1-1.
Splices in main flexural reinforcement of
CPMs shall be located away from the
critical zones where the moment
demands are greater than 75% of the
maximum moment demands in the
member.
8.2.3.2 Hoop Splices and Spiral C8.2.3.2

Terminations
The splice and termination types for Where a full roll of spiral reinforcement
transverse reinforcement in capacity is inadequate for a pile founded in class
protected members shall be as specified S1 soil, the mechanical lap splice detail
in Table 8.2.3.2-1. The splice and shown in Figure C8.2.3.2-1 may be used
termination detail shall be shown on the to splice the spiral reinforcement.
plans.
Combination of spiral reinforcement
with hoops shall not be used except in the
superstructure, where hoops may replace
spirals in order to reduce rebar
congestion.
The spiral reinforcement used in piles
within a pile group in class S1 soil shall be
continuous spiral with a termination Type
2 at the ends of the piles, as shown in Mechanical Lap Splice
Figure 8.2.2.3-1. Where a full roll of spiral Figure C3.2.3.2-1 Spiral Splice
reinforcement is inadequate for a pile, the
spiral may be terminated and restarted
with termination Type 2 or spliced with a
mechanical splice.
Table 8.2.3.2-1 Applicability of Transverse Reinforcement in Capacity Protected

Members
Capacity Protected Transverse Reinforcement
Member Hoops Spiral
Required with Ultimate
Type II Shafts Not allowed
butt splice
Allowed when rebar cage
Piles within a Pile/Shaft Allowed when rebar cage
diameter ≥ 14 in.
group in class S1 soil diameter < 30 in.
(with Service splice)
8.3 DEVELOPMENT OF
LONGITUDINAL REINFORCEMENT IN
SEISMIC CRITICAL MEMBERS
8.3.1 Minimum Development Length of
Longitudinal Reinforcement into Bent
Caps and Footings
8.3.1.1 General C8.3.1.1
Longitudinal reinforcement in SCMs The minimum length of straight,
shall be extended into cap beams and hooked, and headed longitudinal bars
footings as close as practically possible to extended into slab bridge superstructures
the top surface of the cap beam and are specified in Section 9.2.
bottom surface of the footing. While it is expected that the use of
Except for slab bridge hooked bar termination will reduce the
superstructures, the minimum length of anchorage requirement specified in
straight and hooked longitudinal bars Equation 8.3.1.1-1, no such reduction is
extended into cap beams and footings permitted until definitive test data on
shall be taken as: hooked bar termination become available.
In a study of development length
lac = 24dbl (8.3.1.1-1) provisions for column longitudinal bars
extended into cap beams (Unanwa and
where: Mahan, 2012), it was shown that, for the
lac = minimum length of longitudinal least expected concrete compressive
reinforcement in SCM extended strength of 5 ksi required by Section 3.3.6
into cap beams or footings (in.) (Equation 3.3.6-4), the minimum
dbl = nominal bar diameter of development length, lac = 24dbl is similar
longitudinal reinforcement (in.) to those specified by AASHTO (2012) and
Priestley (1996) but is conservative
The minimum length of longitudinal relative to AASHTO (2012) and Priestley
bars with full-size headed bar et al. (1996) for higher concrete strengths.
terminations extended into cap beams
and footings shall be taken as:
lac = 18dbl (8.3.1.1-2)
8.3.1.2 Epoxy-Coated Longitudinal Bars

For epoxy-coated longitudinal bars,
the minimum development lengths shall
be taken as the values determined by
Equation 8.3.1.1-1 or 8.2.1.1-2 multiplied
by a factor of 1.2.

8.3.1.3 Bundled Bars

The minimum development length of
individual bundled bars in SCMs
extended into a bent cap or footing shall
be increased by twenty percent for a two-
bar bundle and fifty percent for a three-bar
bundle over the minimum development
length of an individual unbundled bar.
Four-bar bundles shall not be permitted in
SCMs.
8.3.1.4 Confinement Along Development

Length
The longitudinal reinforcement in
SCMs shall be confined along the
development length, lac by transverse
hoops or spirals with the same volumetric
ratio as that required at the top or bottom,
as applicable, of the SCMs.

8.3.2 Embedment Length and C8.3.2

Clearances for Column Reinforcement
Extended into Type II Shafts
Longitudinal reinforcement in columns The embedment lengths specified in
shall be embedded into Type II shafts, a Table 8.3.2-1 eliminate the staggered
minimum distance as specified in Table arrangement (i.e., alternate lengths) of
8.3.2-1. the column longitudinal bars but result in
In Table 8.3.2-1: development lengths comparable to those
Dc,max = largest cross-sectional calculated with the previous SDC Version
dimension of the column (in.) 1.7. The first term of the embedment
dbl = nominal diameter of the column length, Dc,max is intended to mitigate
longitudinal bar (in.) potential penetration of splitting cracks
into the shaft while the second term
The portion of the column cage accounts for development of the column
embedded in the shaft shall maintain the longitudinal bars. The specified
following reinforcing bar clearances: development lengths meet or exceed the
• Shafts with Construction Joint basic tension development lengths
A 3.5 in. x 3.5 in. minimum clear specified in AASHTO (2012).
window between the horizontal The specified embedment length is
and vertical column reinforcing conservative relative to that obtained
steel through experimental and analytical
• Shafts without Construction Joint research (Murcia-Delso et al., 2013), but
A 5 in. x 5 in. minimum clear was adopted to ensure an adequate
window between the horizontal factor of safety against potential splitting
and vertical column reinforcing cracks and anchorage of the column
steel longitudinal bars beyond the plastic hinge
penetration in the shaft.
The designer should consider
constructability issues if embedment
lengths exceed 20 feet.
Table 8.3.2-1 Embedment Length of Column Bars into Type II Shafts
Embedment Length (in.)

Bar size #
Epoxy-coated bars Non-epoxy-coated bars
11 and smaller Dc,max + 50dbl Dc,max + 42dbl
14 and 18 Dc,max + 58dbl Dc,max + 48dbl

8.3.3 Reinforcing Bar Hooks

Reinforcing bar hooks in seismic
critical members shall be seismic hooks,
defined as hooks with at least a 135° bend
and a straight extension of at least 6db or
3 in., whichever is greater. Seismic hooks
shall be detailed and shown on the plans.
8.4 SPACING OF REINFORCEMENT IN

SEISMIC CRITICAL MEMBERS
8.4.1 Maximum spacing of Transverse
Reinforcement
8.4.1.1 Inside the Plastic Hinge Region C8.4.1.1
The maximum spacing of transverse The maximum spacing requirements
reinforcement in the plastic hinge regions should prevent the buckling of longitudinal
shall be taken as the smallest of the reinforcement between adjacent layers of
following: transverse reinforcement.
• Six times the nominal diameter of
the longitudinal reinforcement
• Eight inches
8.4.1.2 Outside the Plastic Hinge Region

The maximum spacing of transverse
reinforcement outside the plastic hinge
regions where the shear demand in the
SCM is greater than the shear capacity
provided by the concrete, shall be taken
as the smallest of the following:
• One half of the least dimension or
diameter of the SCM
• Nine times the nominal diameter of
the longitudinal reinforcement
• Ten inches
The maximum spacing of transverse

reinforcement outside the plastic hinge
regions where the shear demand in the
SCM is less than the shear capacity
provided by the concrete, shall be as
specified in Section 5 of AASHTO-CA
BDS.

8.4.2 Maximum and Minimum Lateral C8.4.2

Spacing of Longitudinal
Reinforcement
The maximum center to center lateral Research has shown that the lateral
spacing of longitudinal reinforcement spacing of longitudinal bars in circular
shall be 10 inches for SCMs with reinforced concrete members has little
diameters less than or equal to 5 ft and 12 effect on the effectiveness of the
inches for SCMs with diameters larger confinement and ductility of the member
than 5 ft. (Mander et al., 1988b; Papadopoulos and
Longitudinal reinforcing bars in the Shing, 2014) and that a circumferential
interlocking portion of a SCM shall have a spacing larger than the traditionally
maximum lateral spacing of 12 inches. recommended maximum spacing of 8
The minimum lateral spacing of inches can be used without a detrimental
longitudinal reinforcement in columns and effect on flexural ductility and structural
piles shall be as specified in Section 5 of performance (Papadopoulos and Shing,
AASHTO-CA BDS. 2014).
The minimum lateral spacing of The maximum lateral spacing of
longitudinal bars in Types I and II shafts longitudinal reinforcement specified
shall be as specified in Sections 5 and 10 herein is also applicable to Type II shafts.
of AASHTO-CA BDS.

SECTION 9: SLAB BRIDGES 9-1
SECTION 9
SLAB BRIDGES
9.1 GENERAL C9.1

Slab bridges shall meet all the The slab bridge provisions are for
strength and ductility requirements of the cast-in-place slab bridges and
SDC. If any provision of this section precast/voided slab bridges that emulate
conflicts with other sections of the SDC, continuous cast-in-place slab bridges.
this section shall govern for the seismic
design of slab bridges. Slab bridges
designed on the basis of the design charts
in BDA 4-10 shall satisfy all applicable
seismic provisions of the SDC.
Slab bridges shall not be required to
comply with the provisions of Sections
7.2.2 (Vertical Acceleration) and 7.2.3.3
(Hinge Shear Key transverse
requirements).
9.2 SLAB DEPTH C9.2

The depth of slab superstructures Slab bridge superstructures usually
shall be adequate to develop the have relatively shallow depths which also
longitudinal reinforcing bars from the makes it difficult to satisfy seismic
supporting SCMs. requirements. To ensure that slab depths
The minimum length of longitudinal are adequate to develop the longitudinal
reinforcing bars in SCMs extended into bars in SCMs and resist the overstrength
the cap beam shall be taken as: demands generated at the top of SCMs
• Straight bars: 24dbl while remaining essentially elastic, the
• Hooked bars: 19dbl following measures are recommended:
• Full size Headed bars: 11dbl • Use a drop cap/haunched slab
• Increase the slab depth
• Pin the top of SCMs
• Use a reduced SCM section
between the slab and end of the
SCM

The minimum development length of

11dbl for headed bars is only valid for #9
and smaller bar sizes. Research
(Papadopoulos et al., 2015) has shown
that embedment lengths as low as 8.7dbl
can develop the tensile strength of
headed bars if punching damage can be
controlled.
For the definition of Full-size Headed
bars, refer to Section C6.3.5.
9.3 EFFECTIVE WIDTH FOR JOINT C9.3

SHEAR
slab slab
The effective width of slab, Beff at the If the effective width of slab, Beff for
SCM-to-superstructure joint, resisting the slab
one column overlaps with Beff for an
overstrength moment of SCMs shall be adjacent column, the entire width
taken as: between the columns is effective.
slab
Beff = Dc + 2Ds (9.3-1)
where:
Ds = depth of slab at the SCM support
The area of slab with the dimension,

slab
Beff in the transverse and longitudinal
directions, as shown in Figure 9.3-1, shall
define the regions for placement of joint
shear reinforcement as follows:
• Core Region – region of slab-to-
SCM joint directly above the SCM
• Joint Region – region of slab-to-
SCM joint with plan dimensions of
(Dc + Ds ) in both the longitudinal
and transverse directions.
• Joint Perimeter – region of slab-to-
SCM joint outside the “Joint” region
defined above but within the
slab slab
effective slab area, (Beff × Beff )
For slab bridges with drop caps, the

joint region for placement of joint shear
reinforcement shall be defined by (wcap ×
wcap ), where wcap is the width of the drop
cap.

Figure 9.3-1 Slab Bridge Joint Shear Reinforcement Regions
9.4 DROP CAPS C9.4

Drop caps shall be designed to resist Slab bridges with depths less than 16
the overstrength demands of the inches should have drop caps in order to
supporting SCMs. ensure adequate development of the
The width of drop caps shall not be longitudinal bars in SCMs.
greater than the effective width specified
in Equation 9.3-1
9.5 JOINT SHEAR REINFORCEMENT C9.5

Moment-resisting slab superstructure- For a slab bridge, the effective
to-column joints shall satisfy the horizontal joint area, Ajh and effective
provisions of Sections 7.4.1 (Joint vertical joint area, Ajv for use in Equations
Performance), 7.4.2 (Joint Proportioning), 7.4.2-8 and 7.4.2-9 are:
7.4.4 (Types of Joint), and 7.4.5.1
(Minimum Joint Shear Reinforcement). (Dc + 2Ds )2 without drop cap
Ajh = �
The additional reinforcement required (Dc + 2Ds )wcap with drop cap
for joint shear in monolithic (C9.5-1)
superstructure-to-SCM joints shall be as
specified in Table 9.5-1 and illustrated in (Dc + 2Ds )lac,provided without drop cap
Figure 9.5-1. Ajv = �
wcap lac,provided with drop cap
(C9.5-2)

Vertical stirrups, either as Asj-bar bars in Testing and modeling of pile/shaft-to-

the Core Region or Asjv in the Joint Region slab T-joint and Knee-joint connections
and Joint Perimeter, shall be provided at (Ayoub and Sanders, 2010;
each intersection point of the joint shear Papadopoulos et al., 2015) have
bars. The stirrups shall have hooks demonstrated that appropriately
(≥135°) around the top longitudinal reinforced joint regions will limit damage
jv and force plastic hinging into the SCM.
flexural reinforcement. A s bars shall also However, the use of knee joints is
have 90° hooks around the bottom discouraged for slab bridges.
longitudinal flexural reinforcement. In Table 9.5-1, 100% of the additional
The symbols and parameters in Table reinforcement, Add. Reinf., is placed in
9.5-1 shall be defined as: top
top the top for Acap and 100% is placed in the
Acap = area of top flexural reinforcement bot
bottom for Acap .
in each direction within the
effective width (in.2) The required flexural reinforcement to
bot force the plastic hinge into the SCM may
Acap = area of bottom flexural
be detailed by using appropriate bar sizes
reinforcement in each direction larger than those required by BDA 4-10.
within the effective width (in.2) When a reduced column section
Flexural reinf. Required = the flexural between the slab and end of the SCM is
reinforcement required to force used, Ast is the area of longitudinal steel
plastic hinge into the SCM (in.2), connecting the top of the SCM to the slab.
col
i.e., Mne,slab ≥ 1.2Mp , in which Additional joint shear reinforcement is
Mne,slab is the slab nominal moment illustrated in Figure C9.5-1.
capacity based on expected
material properties.
Ast = area of column longitudinal
(in.2).
Add. Reinf. = additional joint shear
reinforcement (in.2). The limits of
the additional reinforcement shall
be shown on the plans.
u-bar
As = area of additional bent cap
reinforcement (u-shaped) for knee
joints in the transverse direction
(in.2).
Asj-bar = area of “J” shaped bars inside
the Core Region above the SCM
(in.2). Asj-bar bars shall extend down
to the top of the column.
jv
As = total area of vertical stirrups in
each of the Joint Region and Joint
Perimeter (in.2). The stirrups shall
be uniformly distributed.

Asjh = total area of horizontal ties in the

effective width along the
longitudinal direction
Two sets of at least two vertically

distributed ties shall be placed within the
Core Region and one set of at least two
vertically distributed ties shall be placed at
each edge of the Joint Region.
Assf = total area of side face

reinforcement
One set of at least two vertically

distributed bars shall be placed at each
side of the joint effective width along the
transverse direction.
jhc
As = total area of horizontal end ties
along the transverse direction for
knee joints
Av,joint = SCM transverse reinforcement
in the joint region
The number of hoops for the

transverse steel in the joint region shall be
determined as:
0.18Ast
Number of hoops = π (9.5-1)
�A �
2 b
where:
Ab = cross-sectional area of an
individual transverse bar.

Table 9.5-1 Reinforcement for SCM-to-Slab Superstructure Joints
Reinforcement Slab T-Joints Slab Knee-Joints

Name/Location (see Figure 9.5-1) (see Figure 9.5-1)
top bot top bot
Area of flexural Acap , Acap = [Flexural reinf. Acap , Acap = [Flexural reinf.
reinforcement in the
Required + Add. reinf.] Required + Add. reinf.]
longitudinal and
transverse direction Add. reinf. = 0.25Ast (drop cap) Add. reinf. = 0.35Ast (long. dir.)
within the effective U-bar
width Add. reinf. = 0.35Ast (flat slab) As = 0.35Ast (trans. dir.)
J-bars in the core

zone of joint region Asj-bar = 0.35Ast Asj-bar = 0.35Ast
Total area of vertical

stirrups in each of
Joint region and Joint Asjv = 1.15Ast Asjv = 0.85Ast
Perimeter
Horizontal ties Asjh = 0.1Ast Asjh = 0.1Ast
top top
0.1Acap 0.1Acap
Horizontal side
Assf ≥ � or Assf ≥ � or
reinforcement bot bot
0.1Acap 0.1Acap
Horizontal cap end

Asjhc = 0.33As
u-bar
-- min
ties
Transverse column
reinf. extended into Av,joint ≥ 0.18Ast Av,joint ≥ 0.18Ast
slab

Note: Not all reinforcement shown
Figure 9.5-1 Slab Bridge Joint Shear Reinforcement

Figure C9.5-1 Additional Slab Bridge Flexural Reinforcement

9.6 SLAB BRIDGE SUPPORTS C9.6

Pile/shaft extensions supporting slab Precast piles are cast in forms
bridges shall have a minimum diameter of requiring less cover and have no
18 inches (precast pile) or 24 inches inspection tube requirements. Cast-in-
(cast-in-place pile) and shall meet the place (CIP) shafts require more cover and
requirements of Section 6.2.5.4 – Pile and a larger minimum bar spacing than
Shaft Extensions. precast piles to accommodate inspection
The minimum abutment support tubes. The minimum sizes of both precast
length for slab bridges shall be 24 inches. and CIP piles also account for the
External or internal shear keys shall be minimum hoop diameters required for
provided for seat-type abutments. reinforcing bars sizes per MTD 20-9.
In lieu of using an abutment seat, a Examples of acceptable pile extension
pinned connection or a reduced abutment and abutment support details for slab
section may be used between the bridges may be found in Appendix A of
superstructure and the abutment. MTD 20-7.
9.7 SLAB BRIDGE HINGES C9.7

The minimum support length for in- Different configurations of slab bridge
span slab bridge hinges shall be 18 hinges are shown in Figure C9.7-1.
inches. Larger longitudinal displacement
capacity and greater stiffness may be
achieved with Figure C9.7-1(C) where
independent frames eliminate the risk of
unseating altogether.
Longitudinal slab reinforcement may

be splice with a service splice or lap
splice. If a service coupler is used, the
splice may be located anywhere in the
span. If a lap splice is used, the splice
shall be located not less than 0.2L from
the centerline of the bent, where L is the
span length. The lap splices shall be
staggered.

Figure C9.7-1 Slab Bridge Hinge

Options

BIBLIOGRAPHY R-1
BIBLIOGRAPHY
AASHTO. (2011). AASHTO Guide Specifications for LRFD Seismic Bridge Design, 2nd
Edition. American Association of State Highway and Transportation Officials, Washington,
DC.
AASHTO. (current CA approved Edition). AASHTO LRFD Bridge Design Specifications.

American Association of State Highway and Transportation Officials, Washington, D.C.
AASHTO. (2012). AASHTO LRFD Bridge Design Specifications, 6th Edition. American
Association of State Highway and Transportation Officials, Washington, D.C.
ASTM. (2011). Standard Test Method for Standard Penetration Test (SPT) and Split-Barrel
Sampling of Soils, ASTM D1586-11. ASTM International, West Conshohocken, PA.
ATC. (1996). Improved Seismic Design Criteria for California Bridges: Provisional
Recommendations - ATC-3. Applied Technology Council, Redwood City, CA.
Ayoub, M., and Sanders, D.H. (2010). Behavior of Pile Extension Connections to Slab
Bridges under Cyclic Loading. UNR Report No. CCEER 10-06, Department of Civil and
Environmental Engineering, University of Nevada, Reno, NV.
Benzoni, G., Ohtaki, T., Priestley, M.J.N., and Seible, F. (1996). Seismic Performance of
Circular Reinforced Concrete Columns Under Varying Axial Loads. Report No. SSRP-
96/04, University of California, San Diego, CA.
Bozorgzadeh, A., Megally, S.H., Ashford, S., and Restrepo, J.I. (2007). Seismic Response
of Sacrificial Exterior Shear Keys in Bridge Abutments. Report No. SSRP-04/14,
Department of Structural Engineering, University of California, San Diego, CA.
Caltrans. (1997). Seismic Design Criteria Retrofit of the West Approach to the San
Francisco-Oakland Bay Bridge - Draft #14. California Department of Transportation,
Sacramento, CA.
Caltrans. (current CA Amendments date). California Amendments to the AASHTO LRFD

Bridge Design Specifications. California Department of Transportation, Sacramento, CA.
Caltrans. (2015). Standard Specifications 2015. California Department of Transportation,

Sacramento, CA.
Caltrans. (2016). Caltrans Seismic Design Specifications for Steel Bridges, 2nd Edition.
California Department of Transportation, Sacramento, CA.

R-2 SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019
Caltrans Seismic Advisory Board (1994). The Continuing Challenge. Report to the
Director, California Department of Transportation on the 1994 Northridge Earthquake,
California Department of Transportation, Sacramento, CA.
Caltrans. (Various dates). Bridge Memo to Designers (MTD). California Department of

Transportation, Sacramento, CA.
Desroches, R., and Fenves, G.L. (1997). New Design and Analysis Procedures for
Intermediate Hinges in Multiple-Frame Bridges. Report No. UCB/EERC-97/12, Pacific
Earthquake Engineering Research Center, University of California, Berkeley, CA.
Duan, L., and McBride, S.B. (1995). “The Effects of Cap Stiffness on Pile Reactions.”
Concrete International, ACI, Vol. 17, No. 1, 42-44.
Lehman, D.E., and Moehle, J.P. (2000). Seismic Performance of Well-Confined Concrete
Bridge Columns. PEER Report 1998/01, Pacific Earthquake Engineering Research
Center, University of California, Berkeley, CA.
Mahan, M.S. (1996). Procedures in Seismic Analysis and Design of Bridge Structures,
Release II Draft. Caltrans Division of Structures, California Department of Transportation,
Sacramento, CA.
Mander, J.B., Priestley, M.J.N., and Park, R. (1988a). “Theoretical Stress-Strain Model for
Confined Concrete.” Journal of Structural Engineering, ASCE, Vol. 114, No. 8, 1804-1826.
Mander, J.B., Priestley, M.J.N., and Park, R. (1988b). “Observed Stress‐Strain Behavior
of Confined Concrete.” Journal of Structural Engineering, ASCE, Vol. 114, No. 8, 1827-
1849.
Maroney, B.H. (1995). Large Scale Abutment Tests to Determine Stiffness and Ultimate
Strength Under Seismic Loading. Ph.D. Dissertation, University of California, Davis, CA.
Martin, G. R., and Dobry, R. (1994). “Earthquake Site Response and Seismic Code
Provisions.” NCEER Bulletin, Vol. 8, No. 4, National Center for Earthquake Engineering
Research, Buffalo, NY.
Menun, C., and Der Kiureghian, A. (1998). “A Replacement for the 30 %, 40 %, and SRSS
Rules for Multicomponent Seismic Analysis.” Earthquake Spectra, Vol. 14, No. 1, 153 -
163.
Murcia-Delso, J., Shing, P.B., Stavridis, A., and Liu, Y. (2013). Required Embedment
Length of Column Reinforcement Extended into Type II Shafts. Report No. CA14-2240,
Nuncio-Cantera, J.A., and Priestley, M.J.N. (1991). Moment Overstrength of Circular and
Square Bridge Columns. Report No. SSRP-91/04, University of California, San Diego, CA.

BIBLIOGRAPHY R-3
Overby, D., Kowalsky, M., and Seracino, R. (2015). A706 Grade 80 Reinforcement for
Seismic Applications. Research Report No. RD-15-15, Constructed Facilities Laboratory,
Department of Civil, Construction, and Environmental Engineering, North Carolina State
University, Raleigh, NC.
Papadopoulos, V., and Shing, P.B. (2014). Influence of Spacing of Longitudinal

Reinforcement on the Performance of Laterally Loaded CIDH Piles - Experimental
Investigation. Report No. SSRP-14/08, Department of Structural Engineering, University
of California, San Diego, CA.
Papadopoulos, V., Murcia-Delso, J., and Shing, P.B. (2015). Development Length for
Headed Bars in Slab-Column Joints of RC Slab Bridges. Report No. SSRP-15/10,
Park, R., and Paulay, T. (1975). Reinforced Concrete Structures, John Wiley & Sons, New
York, NY.
Priestley, M.J.N., and Seible, F. (1991). Seismic Assessment and Retrofit of Bridges.
Structural Systems Research Project, Report No. SSRP-91/03, University of California
San Diego, CA.
Priestley, M.J.N., Seible, F., and Calvi, G.M. (1996). Seismic Design and Retrofit of
Bridges, John Wiley & Sons, New York, NY.
Rinne, E.E. (1994). “Development of New Site Coefficient of Building Codes.” Proceedings
of the Fifth U.S. National Conference on Earthquake Engineering, EERI, Vol. III, 69 -78.
Rollins, K.M., and Cole, R.T. (2006). “Cyclic Lateral Load Behavior of a Pile Cap and
Backfill.” J. Geotech. & Geoenviron. Eng., ASCE, Vol. 132, No. 9, 1143-1153.
Rollins, K.M., and Jessee, S.J. (2013). “Passive Force-Deflection Curves for Skewed
Abutments.” J. Bridge Eng., ASCE, Vol. 18, No. 10, 1086-1094.
Saini, A., and Saiidi, M.S. (2014). Probabilistic Damage Control Approach for Seismic
Design of Bridge Columns. Department of Civil and Environmental Engineering, University
of Nevada, Reno, NV.
Schoettler, M.J., Restrepo, J.I., Guerrini, G., Duck, D.E., and Carrea, F. (2015). A Full-
Scale, Single-Column Bridge Bent Tested by Shake-Table Excitation. PEER Report No.
2015/02, Pacific Earthquake Engineering Research Center, University of California,
Berkeley, CA.
Seible, F., Priestley, M.J.N., Latham, C.T., and Silva, P. (1994). Full-scale Bridge
Column/Superstructure Connection Tests Under Simulated Longitudinal Seismic Loads.
Structural Systems Research Project, Report SSRP-94/14, University of California, San
Diego, CA.

Seible, F., Priestley, M.J.N., Silva, P., and Gee, D. (1994). Full-scale Bridge Column Test
of Redesigned Cap/Column Connection with # 18 Column Bars. Test Report No. TR-
94/01, Charles Lee Powell Structural Research Laboratories, University of California, San
Diego, CA.
Shamsabadi, A., Khalili-Tehrani, P., Stewart, J.P., and Taciroglu, E. (2010). “Validated
Simulation Models for Lateral Response of Bridge Abutments with Typical Backfills.” J.
Bridge. Eng., ASCE, Vol. 15, No. 3, 302-311.
Shamsabadi, A., and Rollins, K.M. (2014). “Three-Dimensional Nonlinear Continuum

Seismic Soil-Structure Interaction Analysis of Skewed Bridge Abutments.” Proc. 8th
European Conference on Numerical Methods in Geotechnical Engineering, Delft, The
Netherlands, June 18-20.
Shamsabadi, A., Rollins, K.M., and Kapuskar, M. (2007). “Nonlinear Soil-Abutment-Bridge

Structure Interaction for Seismic Performance-based Design.” J. Geotech. & Geoenviron.
Eng., ASCE, Vol. 133, No. 6, 707-720.
Stewart, P.S., Taciroglu, E., Wallace, J.W., Ahlberg, E.R., Lemnitzer, A., Rha, C., and
Tehrani, P.K. (2007). Full Scale Cyclic Testing of Foundation Support Systems for
Highway Bridges, Part II: Abutment Backwalls. Report No. UCLA-SGEL 2007/02,
Department of Civil and Environmental Engineering, University of California, Los Angeles,
CA.
Unanwa, C. and Mahan, M. (2014). “Statistical Analysis of Concrete Compressive

Strengths for California Highway Bridges.” Journal of Performance of Constructed
Facilities, ASCE, Vol. 28, No. 1, 157-167.
Unanwa, C.O., and Mahan, M. (2012). A Reevaluation of Provisions for Minimum

Development Length of Column Longitudinal Bars Extended into Cap Beams. General
Earthquake Engineering Report, California Department of Transportation, Sacramento,
CA.
Unanwa, C., and Mahan, M. (2018). Use of a Minimum Transverse Reinforcement Ratio
as a Replacement for Specified Minimum Local Displacement Ductility Capacity. General
Earthquake Engineering Report, California Department of Transportation, Sacramento,
CA.
Veletsos, A.S., and Newmark, N.M. (1960). “Effects of Inelastic Behavior on the Response
of Simple Systems to Earthquake Motions.” Proceedings, 2nd World Conference on
Earthquake Engineering, Tokyo, Japan, pp. 895-912.
Vosooghi, A., and Saiidi, M. (2010). “Seismic Damage States and Response Parameters
for Bridge Columns.” Structural Concrete in Performance-Based Seismic Design of
Bridges, SP-271, P. F. Silva and R. Valluvan, eds., American Concrete Institute,
Farmington Hills, MI, pp. 29-46.

BIBLIOGRAPHY R-5
Vander Werff, J., Peggar, R., Cheng, Z., and Sritharan, S. (2015). Seismic Performance
of Precast Girder-to-Cap Connections for Accelerated Bridge Construction of Integral
Bridges. Report No. CA15-2265, Department of Civil, Construction and Environmental
Engineering, Iowa State University, Ames, IA.
Wibowo, H., Sanford, D.M., Buckle, I.G., and Sanders, D.H. (2013). The Effect of Live
Load on the Seismic Response of Bridges. Report No. CCEER 13-10, Center for Civil
Engineering Earthquake Research, Department of Civil and Environmental Engineering,
University of Nevada, Reno, NV.
Yoon, Y.H., Ataya, S., Mahan, M., Malek, A., and Zokaie, T. (2018). Probabilistic Damage
Control Approach (PCDA) Application to Ordinary Standard Bridge Design, Version 1.0.
Structure Policy and Innovation Report, California Department of Transportation,
Sacramento, CA.

This page intentionally left blank.

APPENDIX A: SEISMIC DESIGN PROCEDURE FLOWCHART A-1
APPENDIX A
SEISMIC DESIGN PROCEDURE FLOWCHART

A-2 SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019

APPENDIX B: DESIGN SPECTRUM DEVELOPMENT B-1
APPENDIX B
DESIGN SPECTRUM DEVELOPMENT
California Seismic Hazard

Seismic hazard in California is governed by shallow crustal tectonics, with the sole
exception of the Cascadia subduction zone along California’s northern coastline. In both
regimes, the Design Response Spectrum is based on the USGS Seismic Hazard Map
(currently 2008 edition - Petersen, 2008) for the 5% in 50 years probability of exceedance
(or 975-year return period). Adjustment factors for near-fault effects and basin amplification
are also applied as described in the sections below.
Spectrum Adjustment Factors

The design spectrum may need to be modified to account for seismological effects
related to being in close proximity to a rupturing fault and/or placement on top of a deep
sedimentary basin. These adjustments are discussed in the following sections.
Near-Fault Factor
Sites located near a rupturing fault may experience elevated levels of shaking at periods
longer than 0.5 second due to phenomena such as constructive wave interference,
radiation pattern effects, and static fault offset (fling). As a practical matter, these
phenomena are commonly combined into a single “near-fault” adjustment factor. This
adjustment factor, shown in Figure B.1, is fully applied at locations with a site to rupture
plane distance (RRup ) of 15 km (9.4 miles) or less and linearly tapered to zero adjustment
at 25 km (15.6 miles). The adjustment consists of a 20% increase in spectral values with
corresponding period longer than one second. This increase is linearly tapered to zero at
a period of 0.5 second.
For application to a probabilistic spectrum, a deaggregation of the site hazard at a
spectral period of 1-second should be performed to determine whether the “probabilistic”
distance is less than 25 km. The “probabilistic” distance shall be calculated as the smaller
of the mean distance and the mode distance (from the distance-magnitude combination
that has the largest contribution to the hazard), but not less than the site to rupture plane
distance corresponding to the nearest fault in the Caltrans Fault Database. This latter
requirement reflects the intention not to apply a near-fault adjustment factor to a
background seismic source used in the probabilistic seismic hazard analysis.
Basin Factor
Both the Campbell-Bozorgnia (2008) and Chiou-Youngs (2008) ground motion
prediction models include a depth to rock (Z) parameter that allows each model to better
predict ground motion in regions with deep sedimentary structure. The two models use
different reference velocities for rock, with Campbell-Bozorgnia using a depth to 2.5 km/s
shear wave velocity (Z2.5) and Chiou-Youngs using a depth to 1.0 km/s shear wave velocity
(Z1.0). Numerical models suggest that ground shaking in sedimentary basins is impacted

B-2 SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019
by phenomena such as trapped surface waves, constructive and destructive interference,

amplifications at the basin edge, and heightened 1-D soil amplification due to a greater
depth of soil. Since neither the Campbell-Bozorgnia nor Chiou-Youngs models consider
these phenomena explicitly, it is more accurate to refer to predicted amplification due to
the Z parameter as a “depth to rock” effect instead of a basin effect. However, since sites
with large depth to rock are located in basin structures the term “basin effect” is commonly
used.
Amplification factors for the two models are shown for various depths to rock in Figure
B.2. These plots assume a shear wave velocity for the upper 30 m of the soil profile, vs30
of 270 m/s (typical for many basin locations) but are suitable for other vs30 values as well
since the basin effect is only slightly sensitive to vs30 (primarily at periods less than 0.5
second). It should be noted that both models predict a decrease in long period energy for
cases of shallow rock (Z2.5 < 1 km or Z1.0 < 40 m). Since Z2.5 and Z1.0 data are generally
unavailable at non-basin locations, implementation of the basin amplification factors is
restricted to locations with Z2.5 larger than 3 km or Z1.0 larger than 400 m.
Maps of Z1.0 and Z2.5

Figures B.3 through B.9 show contour maps of Z1.0 and Z2.5 for regions with sufficient
depth to rock to trigger basin amplification. In Southern California, these maps were
generated using data from the Community Velocity Model (CVM) Version 4
(http://scec.usc.edu/scecpedia/Community_Velocity_Model). In Northern California, the
Z2.5 contour map was generated using tomography data by Thurber (2009) and a
generalized velocity profile by Brocher (2005). A Z1.0 contour map could not be created in
Northern California due to insufficient data.
Application of the models

For Southern California locations, an average of the Campbell-Bozorgnia and Chiou-
Youngs basin amplification factors is applied. For Northern California locations, only the
Campbell-Bozorgnia basin amplification factor is applied.
Directional Orientation of Design Spectrum

When recorded horizontal components of earthquake ground motion are
mathematically rotated to different orientations, the corresponding response spectrum
changes as well. The probabilistic spectra defined above reflect a spectrum that is equally
probable in all orientations. The maximum response spectrum, occurring at a specific but
unpredictable orientation, is approximately 15% to 25% larger than the equally probable
spectrum calculated using the procedures described above. Since a narrow range of
directional orientations typically define the critical loading direction for bridge structures,
the equally probable component spectrum is used for design.
Selection of vs30 for Site Amplification

The Campbell-Bozorgnia (2008), Chiou-Youngs (2008), and Boore-Atkinson (2008)
ground motion prediction models (the latter is included for application to the probabilistic
spectrum) use the parameter vs30 to characterize near surface soil stiffness as well as infer
broader site characteristics. vs30 represents the average small strain shear wave velocity

in the upper 100 feet (30 meters) of the soil column. This parameter, along with the level
of ground shaking, determines the estimated site amplification in each of the above models.
If the shear wave velocity (vs30 ) is known (or estimated) for discrete soil layers, then vs30
can be calculated as follows:
100ft
vs30 = D D
1 + 2 +…+ Dn
v v1 1 v n
where, Dn represents the thickness of layer n (ft), vn represents the shear wave velocity of
layer n (fps), and the sum of the layer depths equals 100 feet. It is recommended that direct
shear wave velocity measurements be used, or, in the absence of available field
measurements, correlations to available parameters such as undrained shear strength,
cone penetration tip resistance, or standard penetration test blow counts be utilized.
Additional recommendations pertaining to determination of vs30 for development of the
preliminary and final design spectrum are given in "Methodology for Developing Design
Response Spectra” available in the Technical References link of the ARS Online V2
website (http://dap3.dot.ca.gov/shake_stable/v2/).
Figure B.10 provides a profile classification system that is published in Applied
Technology Council–32 (1996) and was adopted in previous versions of SDC. This table
includes general guidance on average shear wave velocity that may be useful for
development of a preliminary design spectrum. The Campbell-Bozorgnia and Chiou-
Youngs ground motion prediction equations are applicable for vs30 ranging from 150 m/s
(500 fps) to 1500 m/s (5000 fps). For cases where vs30 exceeds 1500 m/s (very rare in
California), a value of 1500 m/s should be used. For cases where either (1) vs30 is less than
150 m/s, (2) one or more layers of at least 5 feet thickness has a shear wave velocity less
than 120 m/s, or (3) the profile conforms to Soil Profile Type E criteria per Figure B.10, a
site-specific response analysis is required for determination of the final design spectrum.
For cases where the site meets the criteria prescribed for Soil Profile Type E, the
response spectra presented in Figures B.11 - B.13, originally presented in ATC-32, can be
used for development of a preliminary design spectrum. In most cases, however, Type E
spectra will significantly exceed spectra developed using site response analysis methods.
For this reason, it is preferred that a site response analysis be performed for the
determination of the preliminary design spectrum in Type E soils.
When a soil profile meets the criteria prescribed for Soil Profile Type F (in Figure B.10),
a site response analysis is required for both preliminary and final design.
References
Applied Technology Council (1996). Improved Seismic Design Criteria for California
Bridges: Resource Document, Publication 32-1, Redwood City, California.
Boore, D., and Atkinson, G. (2008). “Ground-motion Prediction Equations for the Average
Horizontal Component of PGA, PGV, and 5%-damped PSA at Spectral Periods between
0.01 s and 10.0 s.” Earthquake Spectra, Vol. 24, pp. 99 - 138.
Brocher, T.M. (2005). “A Regional View of Urban Sedimentary Basins in Northern

California Based on Oil Industry Compressional-wave Velocity and Density Logs.” Bull.
Seism. Soc. Am., Vol. 95, 2093-2114.
California Geological Survey (CGS). (2005). “Digital Database of Quaternary and Younger
Faults from the Fault Activity Map of California.” Version 2.0 Bryant, W.A. (compiler),
<http://www.conservation.ca.gov/cgs/information/publications/Pages/QuaternaryFaults_v
er2.aspx> (October 26, 2017).
California Geological Survey (CGS). (1997) (rev. 2008). “Guidelines for Evaluating and
Mitigating Seismic Hazards in California: Special Publication 117A,
<http://www.conservation.ca.gov/cgs/shzp/webdocs/Documents/sp117.pdf> (October 26,
2017).
Campbell, K., and Bozorgnia, Y. (2008). “NGA Ground Motion Model for the Geometric
Mean Horizontal Component of PGA, PGV, PGD, and 5% Damped Linear Elastic
Response Spectra for Periods Ranging from 0.01 to 10 s.” Earthquake Spectra, Vol. 24,
pp. 139 - 172.
Chiou, B., and Youngs, R. (2008). “An NGA Model for the Average Horizontal Component
of Peak Ground Motion and Response Spectra.” Earthquake Spectra, Vol. 24, 173-216
Frankel, A.D., Petersen, M.D., Mueller, C.S., Haller, K.M.,Wheeler, R.L., Leyendecker,
E.V., Wesson, R.L., Harmsen,S.C., Cramer, C.H., Perkins, D.M., and Rukstales, K.S.
(2002). Documentation for the 2002 Update of the National Seismic Hazard Maps, U.S.
Geological Survey Open-File Report 2002–420, 39 p.
Petersen, M.D., Frankel, A.D., Harmsen, S. C., Mueller, C.S., Haller, K.M., Wheeler, R.L.,
Wesson, R.L., Zeng, Y., Boyd, O.S., Perkins, D.M., Luco, N., Field, E.H., Wills, C.J., and
Rukstales, K.S. (2008). Documentation for the 2008 Update of the United States National
Seismic Hazard Maps, U.S. Geological Survey Open-File Report 2008–1128, 61 p.
Southern California Basin Models (2010). “Community Velocity Model Version 4.0”
<http://scec.usc.edu/scecpedia/Community_Velocity_Model> (October 26, 2017).
Thurber, C., Zhang, H., Brocher, T., and Langenheim, V. (2009). “Regional Three-
dimensional Seismic Velocity Model of the Crust and Uppermost Mantle of Northern
California.” J. Geophys. Res., 114, B01304 pp.
USGS Probabilistic Seismic Hazard Analysis

<https://earthquake.usgs.gov/hazards/hazmaps/> (October 26, 2017).
Youngs, R.R., Chiou, S.J., Silva W.J., and Humphrey, J.R. (1997). “Strong Ground Motion
Attenuation Relationships for Subduction Zone Earthquakes.” Seism. Res. Letts., Vol. 68,
No. 1, 58 - 73.

Near-Fault Factor with Respect to Distance Near-Fault Factor with Respect to Period
1.3
1.3
(for 15km or less)

Amplification
Amplification
1.2 1.2
1.1 1.1
1
1
0 5 10 15 20 25 30
0 1 2 3 4 5
Distance (km) Period (s)
Figure B.1 Near-Fault adjustment factor as a function of distance and spectral period. The
distance measure is based on the closest distance to any point on the fault plane
1.8 Z2.5 = 6 km 1.8
5.5 km
1.6 1.6 Z1.0 = 1000 m

5 km 900 m
Amplification Factor
Amplification Factor
800 m
700 m
4.5 km
1.4 1.4
600 m
4 km
1.2 1.2 500 m

3.5 km
400 m
3 km
1 1
0 1 2 3 4 5 0 1 2 3 4 5
Period (s) Period (s)
Figure B.2 Basin amplification factors for the Campbell-Bozorgnia (2008) and Chiou-
Youngs (2008) ground motion prediction equations. Curves may be slightly conservative
at periods less than 0.5 seconds

Los Angeles Basin Z1.0
-118.6 -118.4 -118.2 -118.0 -117.8

34.2 34.2
60
0
34.0 50
0 34.0
80
60 700 0
0
50
Latitude (deg)
40 0
0
33.8 33.8
33.6 33.6
33.4 33.4
-118.6 -118.4 -118.2 -118.0 -117.8
Longitude (deg)
Figure B.3 Contours of depth (meters) to shear wave velocity 1 km/s (Z1.0) in the Los
Angeles Basin

Los Angeles Basin Z2.5
-118.6 -118.4 -118.2 -118.0 -117.8 -117.6 -117.4

34.1 34.1
3500
34.0 34.0
Latitude (deg)
3500
60
00
33.9 33.9
50 400
35
00
00
0
30
00
33.8 33.8
33.7 33.7
-118.6 -118.4 -118.2 -118.0 -117.8 -117.6 -117.4
Longitude (deg)
Figure B.4 Contours of depth (meters) to shear wave velocity 2.5 km/s (Z2.5) in the Los
Angeles Basin

Ventura Basin Z1.0
-119.4 -119.2 -119.0 -118.8 -118.6

34.5 34.5
34.4 34.4
0
60 00
8
00
10
Latitude (deg)
34.3 34.3
34.2 34.2
700
600
50
0
34.1 34.1
-119.4 -119.2 -119.0 -118.8 -118.6
Longitude (deg)
Figure B.5 Contours of depth (meters) to shear wave velocity 1 km/s (Z1.0) in the Ventura
Basin

Ventura Basin Z2.5
-119.6 -119.4 -119.2 -119.0 -118.8 -118.6

34.6 34.6
34.5 34.5
34.4 34.4
00
Latitude (deg)
60 00
50 0
400
00
30
34.3 34.3
34.2 34.2
34.1 34.1
-119.6 -119.4 -119.2 -119.0 -118.8 -118.6
Longitude (deg)
Figure B.6 Contours of depth (meters) to shear wave velocity 2.5 km/s (Z2.5) in the Ventura
Basin

Salton Basin Z1.0
-117.0 -116.5 -116.0 -115.5 -115.0 -114.5 -114.0

34.0 34.0
400 700
33.6 33.6
400
33.2 33.2
Latitude (deg)
700
400
700
32.8 32.8
400 400
700
400
32.4 32.4
700
400
32.0 32.0
31.6 31.6
-117.0 -116.5 -116.0 -115.5 -115.0 -114.5 -114.0
Longitude (deg)
Figure B.7 Contours of depth (meters) to shear wave velocity 1 km/s (Z1.0) in the Salton
Basin (Imperial Valley)

Salton Basin Z2.5
-116.4 -116.0 -115.6 -115.2 -114.8

34.0 34.0
33.6 35
00
33.6
3000
33.2 33.2
Latitude (deg)
3500 4000
3000
3500
32.8 32.8
300
0
32.4 32.4
50
40 0
00
30
00
0
32.0 32.0
-116.4 -116.0 -115.6 -115.2 -114.8
Longitude (deg)
Figure B.8 Contours of depth (meters) to shear wave velocity 2.5 km/s (Z2.5) in the Salton
Basin (Imperial Valley)

Northern California Z2.5
-122.8 -122.4 -122.0 -121.6 -121.2 -120.8

40.0 40.0
30
39.5 39.5
00
35
00
39.0 39.0
4000
Latitude (deg)
35
00
30
00
38.5 38.5
40
00
3500
38.0 35 38.0
300
00
0
3000
37.5 37.5
-122.8 -122.4 -122.0 -121.6 -121.2 -120.8
Longitude (deg)
Figure B.9 Contours of depth (meters) to shear wave velocity 2.5 km/s (Z2.5) in Northern
California

Soil
Profile Soil Profile Description a
Type
A Hard rock with measured shear wave velocity vs30 > 5000 ft/s (1,500 m/s)
Rock with shear wave velocity 2,500 < vs30 < 5000 ft/s (760m/s < vs30 < 1,500
B
m/s)
Very dense soil and soft rock with shear wave velocity 1,200 < vs30 < 2,500
C ft/s (360m/s < vs30 < 760 m/s) or with either standard penetration resistance N
> 50 or undrained shear strength su ≥ 2,000 psf (100 kPa)
Stiff soil with shear wave velocity 600 < vs30 < 1,200 ft/s (180 m/s < vs30 < 360
D m/s) or with either standard penetration resistance 15 ≤ N ≤ 50 or undrained
shear strength 1,000 < su < 2,000 psf (50 < su < 100 kPa)
A soil profile with shear wave velocity vs30 < 600 ft/s (180 m/s) or any profile
with more than 10 ft (3 m) of soft clay, defined as soil with plasticity index PI >
E
20, water content w ≥ 40 percent, and undrained shear strength su < 500 psf
(25 kPa)
Soil requiring site-specific evaluation:

1. Soils vulnerable to potential failure or collapse under seismic loading;
i.e. liquefiable soils, quick and highly sensitive clays, collapsible
weakly-cemented soils
F
2. Peat and/or highly organic clay layers more than 10 ft (3 m) thick
3. Very high-plasticity clay (PI > 75) layers more than 25 ft (8 m) thick
4. Soft-to-medium clay layers more than 120 ft (36 m) thick
a The soil profile types shall be established through properly substantiated

geotechnical data.
Figure B.10 Soil profile types (after Applied Technology Council-32-1, 1996)

Figure B.11 Spectral Acceleration and Displacement for Soil Profile E (M = 6.5±0.25)



INDEX I-1
INDEX
Abutment longitudinal stiffness ...................................4-4, 4-9, 4-10, 5-1, 6-23, 6-24, 6-27
Abutment support length .............................................................. 3-18, 5-2, 6-29, 9-9, A-2
Abutment transverse stiffness ....................................................................... 4-9, 5-1, 6-28
Anchorage..................................................................................................... 7-32, 8-6, 8-8
Axial load limits ............................................................................................... 5-7, 5-8, A-1
Balanced frame geometry ............................................................................................. 7-4
Balanced stiffness ..................................................................................6-18, 7-1, 7-3, A-1
Bearings ....................................................................1-8, 4-2, 6-29, 7-14, 7-15, 7-42, 7-43
Bent cap ........................................................................ 3-20, 4-15, 4-17, 5-21, 5-22, 5-23,
7-19, 7-20, 7-22, 7-27, 7-28, 7-29, 7-30, 7-33, 7-44, 8-2, A-1, A-2
Bridge system ................................................................................................. 1-2, 2-1, 4-7
Bundled bars ................................................................................................................. 8-7
Capacity design ..................................................................................................... 1-8, 2-1
Cap beam short stub length ........................................................................................ 7-23
Capacity protected member 1-8, 1-9, 2-1, 3-9, 3-18, 4-14, 4-15, 5-21, 6-16, 6-18, 8-2, 8-5
Class S1 soil ....................................................... 4-14, 6-1, 6-2, 6-8, 6-9, 6-10, 6-11, 6-21
Class S2 soil ................................................. 4-13, 4-14, 6-2, 6-11, 6-12, 6-14, 6-17, 6-21
Column dimensions .................................................................................................... 7-46
Column flares ..................................................................................................... 7-46, 7-48
Column key ........................................................................................................ 7-48, 7-49
Complete Quadratic Combination 3 .............................................................................. 4-5
Comprehensive foundation design.............................................................................. 6-12
Confined concrete .............................................................................. 2-1, 3-12, 3-13, 3-14
Confinement................................................................2-1, 5-7, 5-15, 6-11, 6-21, 6-33, 8-7
Critical pile length................................................................................................. 2-1, 6-21
Damage state......................................................................................................... 1-5, 1-6
Damping................................................................................................................. 2-2, 3-5
Design Seismic Hazards ...............................................1-8, 2-2, 3-1, 3-18, 4-9, 5-21, 6-28
Design Spectrum ......................................... 1-9, 2-2, 3-1, 3-3, 3-4, 4-4, 4-5, B-1, B-2, B-3
Development length ......................................................6-31, 6-33, 7-12, 8-6, 8-7, 8-8, 9-2
Diaphragm abutment ......................................................................................... 6-24, 6-25
Directionality effects ...................................................................................................... 3-4
Displacement capacity ................................................3-16, 3-17, 3-18, 3-19, 5-1, 5-2, 5-3
Displacement coefficient ............................................................................. 4-4, 6-26, 6-27
Displacement demand ................................... 3-16, 3-18, 4-1 to 4-4, 4-7, 4-10, 4-13, 7-14
Displacement ductility demand ........................................................ 4-13, 4-14, 5-13, 5-14
Drop cap .............................................................................. 7-10, 7-11, 7-19, 9-1, 9-2, 9-3
Ductile Member ............................................................................................................. 2-2
Earthquake resisting elements .......................................................... 1-9, 2-2, 3-1, 3-2, 3-3
Earthquake resisting system .............................................1-8, 1-9, 2-2, 3-1, 3-3, 4-15, 5-1
Effective moment of inertia................................................................................. 3-15, 3-16

I-2 SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019
Effective torsional moment of inertia ............................................................................ 3-16

Effective superstructure width ........................................................... 4-17, 5-23, 7-4 to 7-8
Effective width of bent caps .......................................................................... 7-19, 9-2, 9-3
Effective width of slab bridges for joint shear..........................................................9-2, 9-3
Elastic Dynamic Analysis .................................... 3-21, 4-1 to 4-7, 4-12, 6-26 to 6-28, 7-17
Epoxy-coated bars ..................................................................................................8-6, 8-8
Equivalent plastic hinge length ....................................................... 2-2, 5-2, 5-8, 5-9, 7-47
Equivalent Static Analysis ......... 3-16, 3-21, 4-1 to 4-4, 4-6, 4-8, 4-9, 4-12, 5-1, 6-23, 7-16
Essentially elastic .................................................... 1-6, 1-8, 1-9, 2-2, 5-7, 5-21, 7-20, 9-1
Expected material properties ................................................. 2-2, 3-8, 5-10, 5-21, 6-3, 9-4
Fault rupture ...........................................................................................................3-1, 3-7
Footing stirrups .............................................................................................................. 6-5
Footings ................................................................................................................5-21, 6-2
Foundation design ....................................................................................................... 6-12
Functional Evaluation Earthquake ......................................................... 1-5, 2-3, 3-4, 7-43
Global behavior.............................................................................................................. 2-3
Global model ..........................................................................................................4-4, 4-7
Grade 60 steel/reinforcement ....................................................................... 3-8, 3-9, 3-10
Grade 80 steel/reinforcement ....................................................................... 3-8, 3-9, 3-10
Ground shaking ......................................................................................................2-3, 3-1
Headed bars ................................................................................. 3-9, 6-31, 7-20, 8-6, 9-1
Hinge support length.......................................................... 3-18, 7-14, 7-15, 7-17, 9-9, A-2
Hoop reinforcement ..... 5-10, 5-15, 5-16, 5-19, 6-12, 6-21, 7-32, 7-39, 8-3 to 8-5, 8-7, 9-5
Horizontal cap end ties .........................................................................................7-35, 9-6
Horizontal side reinforcement ..................................................................... 7-31, 7-35, 9-6
Horizontal stirrups ...............................................................................................7-31, 7-34
Idealized yield curvature .......................................................................................5-4, 5-11
Important bridge........................................................................................... 1-2, 1-4 to 1-6
Inelastic Static Analysis ....................................................... 2-4, 4-3, 5-1, 6-12, 6-13, 6-23
In-span hinge .............................................................. 3-18, 4-10, 5-21, 7-14 to 7-16, 7-42
Interlocking spiral/hoop .................................................. 5-15, 5-16, 5-19, 5-20, 7-32, 7-39
Isolated shear key........................................................................................................ 6-31
Isolation bearings..................................................................................................3-1, 7-43
J dowels..............................................................................................................7-32, 7-36
Joint shear .................................................................................... 2-3, 6-3, 7-20, 7-22, 9-2
Knee joint......................................................................................................... 7-23 to 7-25
Knee joint shear reinforcement ......................................... 7-23, 7-33 to 7-41, 9-4, 9-5, 9-6
Lap splice ..................................................................................................... 8-1, 8-5, 9-10
Lateral spreading ............................................................................................ 3-1, 3-6, 6-1
Lateral stability ....................................................................................................6-21, 6-22
Liquefaction ........................................................................... 2-3, 3-1, 3-6, 6-1, 6-15, 6-21
Load factor................................................................................................................... 3-21
Local displacement capacity ........................................................................... 5-1, 5-2, 5-3
Local principal axes ..................................................................................................... 3-21
Mander’s model ............................................................................... 3-12, 3-13, 3-14, 5-11
Material properties ......................................................................................................... 3-8

INDEX I-3
Minimum development length ................................................................ 6-31, 8-6, 8-7, 9-1

Moment-curvature analysis ......................................................................................... 5-10
Monolithic shear key .......................................................................................... 6-32, 6-34
Multi-frame bridge ................................................................. 4-4, 4-5, 4-10, 7-15, A-1, A-2
Nominal moment capacity ........................................................................... 5-11, 5-21, 9-4
Nominal shear capacity ............................................................................. 5-12, 5-15, 5-21
Nonlinear time history analysis ....................................3-21, 4-1, 4-2, 4-4, 4-6 to 4-9, 6-23
Nonstandard bridge ............................................................................................... 1-1, 1-2
No-Splice zone......................................................................................... 2-3, 8-1, 8-2, 8-3
Ordinary nonstandard bridge ........................................................................................ 1-2
Ordinary standard bridge ............................................................................ 1-2, 4-14, 5-16
Overstrength moment ................ 2-3, 4-15, 4-16, 5-21, 6-3, 6-5, 6-9, 6-12, 6-19, 7-48, 9-2
Overstrength shear ................................................................... 2-3, 4-15, 5-12, 6-12, 7-16
Partial model ................................................................................................................. 4-7
Peak ground acceleration ........................................................................... 7-9, 7-12, 7-48
P-Δ ................................................................................................... 3-17, 4-13, 4-18, 4-19
Pile/shaft extension .............................................................. 4-14, 5-7, 6-18, 6-21, 8-4, 9-9
Pile foundation .................................................................................................. 6-8 to 6-12
Plastic hinge... 1-8, 2-3, 3-1, 3-16, 3-18, 4-13, 4-14, 4-15, 5-1, 5-4, 5-7, 6-16, 7-46 to 7-48
Plastic hinge region........................................ 2-3, 5-7, 5-12, 5-16, 5-18, 8-1, 8-2, 8-3, 8-9
Plastic moment capacity ........................................................................... 4-15, 5-10, 6-12
Precast girders ............................................................................................ 7-9, 7-10, 7-11
Prestress secondary moments and shears ................................................................... 2-4
Prestressing strand ................................................................... 3-11, 3-12, 7-9, 7-12, 7-13
Pushover Analysis .................................................................. See Inelastic static analysis
Recovery bridge ..................................................................... 1-2, 1-5, 1-6, 1-8, 3-18, 7-43
Recovery nonstandard bridge ....................................................................................... 1-2
Recovery standard bridge ................................................. 1-2, 3-16, 4-14, 5-16, 5-18, A-1
Resistance factor ...................................................................................... 3-21, 5-21, 7-49
Response spectrum .......................................................... 2-4, 3-5, 4-1, 4-6, B-1, B-2, B-3
Restrainers................................................................................................ 7-16, 7-17, 7-18
Sacrificial element ....................................................................... 1-8, 2-4, 4-14, 5-21, 7-42
Safety Evaluation Earthquake ....................................................... 1-5, 2-4, 3-1, 4-13, 7-14
Scour .......................................................................................................... 6-1, 6-15, 6-21
Seat abutment.................................................................................. 6-23, 6-24, 6-25, 6-28
Seismic critical member ........................... 1-8, 1-9, 2-4, 3-1, 3-8, 3-15, 4-13 to 4-15, 4-18,
5-7 to 5-22, 6-2, 6-11, 6-18, 6-21, 7-9, 7-19, 7-32, 7-39,
8-1 to 8-4, 8-6 to 8-10, 9-1 to 9-6
Seismic expansion joints .................................................................................... 5-21, 7-43
Seismic hooks ............................................................................................................... 8-9
Seismic Isolation .................................................................................... 2-4, 3-1, 4-6, 7-43
Service splice ................................................................................ 7-48, 8-1, 8-5, 9-9, 9-10
Shafts ............................................................. 6-1, 6-2, 6-12, 6-16 to 6-22, 6-28, 7-2, 7-44
Shear key ................................................................................. 1-8, 4-9, 6-28, 6-30 to 6-34
Shear reinforcement capacity .................................................................................... 5-14
Skew .... 1-3, 3-6, 4-2, 4-4, 6-23 to 6-26, 6-29, 7-5 to 7-8, 7-15, 7-28 to 7-33, 7-36 to 7-38

I-4 SEISMIC DESIGN CRITERIA VERSION 2.0 APRIL 2019
Slab bridges ........................................................... 7-16, 7-20, 7-21, 7-26, 8-6, 9-1 to 9-10
Soil classification ........................................................................................................... 6-1
Soil springs ................................................................................. 5-1, 6-8, 6-13, 6-15, 6-18
Soil-foundation-structure interaction ................................. 4-6 to 4-8, 4-13, 5-1, 6-11, 6-12
Spacing of reinforcement ........................................ 5-15, 5-16, 5-20, 7-31, 7-35, 8-9, 8-10
Specified minimum material properties .............. 2-2, 2-4, 3-8, 3-10, 3-15, 5-22, 6-19, 7-25
Spectral acceleration ........................................................ 4-3, 4-4, 4-13, B-14, B-15, B-16
Spiral reinforcement............................................................................. 5-15, 5-16, 8-3, 8-5
Spiral termination ............................................................................................ 8-3, 8-4, 8-5
Splice ............................................. 3-9, 5-16, 7-12, 7-33, 7-35, 7-48, 8-1 to 8-5, 9-9, 9-10
Spread footings ..................................................................................... 1-3, 6-2, 6-7, 6-30
Square Root of Sum of Squares .................................................................................... 4-5
Stand-alone analysis ...................................................................... 4-4, 4-10 to 4-12, 6-28
Standard bridge ............................................................ 1-1, 1-2, 1-9, 2-4, 4-14, 5-16, 5-17
Stiffness ...... 1-3, 3-15, 3-16, 4-3, 4-4, 4-8 to 4-10, 6-8, 6-15, 6-18, 7-1, 7-2, 7-3, 7-46, 9-9
(See also “abutment longitudinal stiffness” and “abutment transverse stiffness”)
Superstructure depth ..........................................................................................7-19, 7-46
T joint ........................................................................................................ 7-22, 7-23, 7-26
T joint shear reinforcement ........................................................ 7-26 to 7-32, 9-4, 9-5, 9-6
Transverse reinforcement .................. 5-15 to 5-19, 5-23, 7-25, 7-32, 7-39, 8-1 to 8-5, 8-9
Type I Shaft ....................................................... 2-5, 4-13, 4-14, 4-19, 5-4, 5-7, 5-9, 5-19,
6-16 to 6-18, 6-21, 7-44, 8-4, 8-10
Type II Shaft ........................................................... 2-5, 4-14, 5-8, 5-18, 5-19, 5-21, 5-23,
6-16 to 6-21, 7-44, 8-2, 8-5, 8-8, 8-10
Ultimate butt splice .................................................................................... 5-15, 8-1 to 8-5
Ultimate curvature capacity ........................................................ 2-5, 3-16, 3-18, 5-1, 5-11
Vertical acceleration ............................................................................ 7-9, 7-12, 7-13, 9-1
Vertical stirrups .................................................................. 7-26, 7-31, 7-33, 7-34, 9-4, 9-6
Yield curvature ............................................................................................ 3-15, 5-4, 5-11


Seisdescri

Uploaded by

Copyright:

Available Formats

Seisdescri

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Seisdescri

Uploaded by

Copyright:

Available Formats

CALTRANS

TABLE OF REVISIONS FROM SDC 1.7 TO SDC 2.0

All All Rearranged design provisions in a “Code and Commentary”

1. 1.1 Changed scope of the SDC from “Ordinary Standard bridges” to

2.1 Added “Definitions”

3.1 Added “Earthquake Resisting Elements”

©2019 California Department of Transportation

SDC 1.7 SDC 2.0 Revision

©2019 California Department of Transportation

SDC 1.7 SDC 2.0 Revision

©2019 California Department of Transportation

SDC 1.7 SDC 2.0 Revision

4.3.2 5.4.4 Added equations for Superstructure/Bent cap Seismic Capacity

SDC 1.7 SDC 2.0 Revision

6.2.2 6.1.1 Adopted a new “Soil Classification”

©2019 California Department of Transportation

SDC 1.7 SDC 2.0 Revision

7.1.1 7.1.2 Deleted “Balanced Stiffness” equations for Constant Width

©2019 California Department of Transportation

SDC 1.7 SDC 2.0 Revision

8.2.1 Added provisions on types and uses of “Reinforcing Bar Splices”

©2019 California Department of Transportation

SDC 1.7 SDC 2.0 Revision

Appendix Added a new appendix: “Seismic Design Procedure Flowchart”

Index Added an Index

CHANGES IN SECTION NUMBERING FROM SDC 1.7 TO SDC 2.0

Version 1.7 Version 2.0 Version 1.7 Version 2.0

Version 1.7 Version 2.0 Version 1.7 Version 2.0

1. INTRODUCTION ....................................................................................................... 1-1

1.1 SCOPE .................................................................................................................... 1-1

2. DEFINITIONS, NOTATIONS AND ACRONYMS/INITIALISMS ................................. 2-1

2.1 DEFINITIONS ......................................................................................................... 2-1

3. GENERAL REQUIREMENTS .................................................................................... 3-1

3.1 EARTHQUAKE RESISTING ELEMENTS ................................................................ 3-1

3.2.2 Liquefaction .................................................................................................... 3-6

4. SEISMIC DEFORMATION DEMANDS AND ANALYSIS METHODS ........................ 4-1

4.1 GENERAL ............................................................................................................... 4-1

4.4.1 Displacement Ductility Demand ..................................................................... 4-13

5. SEISMIC DEFORMATION CAPACITIES................................................................... 5-1

5.1 GENERAL ................................................................................................................ 5-1

6. FOUNDATIONS, ABUTMENTS AND SOIL-FOUNDATION-STRUCTURE

6.1 SOIL PROFILE CLASSIFICATION .......................................................................... 6-1

6.2.3.2 Simplified Design for Piles in Class S1 Soil ............................................. 6-9

7. BRIDGE COMPONENTS........................................................................................... 7-1

7.1 FRAMES .................................................................................................................. 7-1

7.2.2 Reinforcement Requirements for Vertical Acceleration ................................. 7-12

7.6.3.2 Vertical Flare Isolation ........................................................................... 7-47

8. SEISMIC DETAILING ................................................................................................ 8-1

8.1 GENERAL ................................................................................................................ 8-1

©2019 California Department of Transportation

9. SLAB BRIDGES ........................................................................................................ 9-1

9.1 GENERAL ............................................................................................................... 9-1

BIBLIOGRAPHY ........................................................................................................... R-1

APPENDIX A - SEISMIC DESIGN PROCEDURE FLOWCHART .................................A-1

APPENDIX B - DESIGN SPECTRUM DEVELOPMENT ...............................................B-1

©2019 California Department of Transportation

1.1 SCOPE C1.1

©2019 California Department of Transportation

Throughout this document, the term