Technical data Tegramin-20 Tegramin-25 Tegramin-30

Diameter 200 mm / 8" 250 mm / 10" 300 mm / 12"

Speed 40-600 rpm, variable in steps of 10

Rotational direction Counter-clockwise

Disc Motor power continuous / max 370 / 555 W / 0.5 / 0.75 HP 750 / 1125 W / 1.0 / 1.5 HP
Torque at disc
Cont. at <300 rpm 11.8 Nm / 8.7 ft-lbf 23.8 Nm / 17.6 ft-lbf
Cont. at 600 rpm 5.9 Nm / 4.4 ft-lbf 11.9 Nm / 8.8 ft-lbf
Max. > 18 Nm / 13.3 ft-lbf > 40 Nm / 29.6 ft-lbf
Speed 50-150 rpm, variable in steps of 10

Rotational direction Clockwise, counter-clockwise

Specimen holder: 30-300 N Specimen holder: 30-400 N
Head Force Individual specimens: 5-50 N
Individual specimens: 5-50 N Individual specimens: 5-65 N
Motor 120 W 160 W

Torque 7.5 Nm / 5.6 ft-lbf 10.2 Nm / 7.6 ft-lbf

Controls Touch pad and turn/push knob

Software and electronics
Memory FLASH-ROM / RAM / NV-RAM

LC Display TFT-colour 320x240 dots with LED back light

Safety Please refer to the Declaration of Conformity

Emergency stop EN60204-1, Stop Category 0
Stop Mechanisms
EN954-1, Category 2
Designed to comply with:
Cover EN60204-1, Stop Category 2
EN954-1, Category B
At idle running, at a distance 1.0 m / 39.4"
47 dBA
from the machine
Noise level
During preparation Polishing 54 dBA, Grinding 56 dBA

Surrounding temperature 5-40°C / 41-104°F

Humidity Non condensing 0-95% RH

Voltage / frequency 200-240 V / 50-60 Hz

1-phase (N+L1+PE) or 2-phase (L1+L2+PE)
Power inlet
The electrical installation must comply with “Installation Category II”.
Power, nominal load 680 W 1060 W
Power, idle 9W 13 W
Current, nom. 3.4 A 5.3 A

Current, max. 6.3 A 10 A

Supply
Pressure for tap water 1-10 bar / 14.5-145 psi

Water inlet ¾"

Water outlet ø30 mm / 1¼" ø40 mm / 1½"

Air inlet ø6 mm

Air pressure 6-10 bar / 86-145 psi

Air quality The air supplied must be of Class-3 or better, as specified in ISO 8573-1.
“Exhaust” ø50 mm / 2"
Dimension
(with Cover only) Recommended capacity for exhaust system: 50 m3/h / 1750 ft3/h at 0 mm water gauge.
Width 60 cm / 23.6" 67.5 cm / 26.6"

Dimensions and weight Depth 65 cm / 25.6" 75 cm / 29.5"

(without Cover) Height 48 cm / 18.9" 56 cm / 22"

Weight 52.5 kg /116 lbs 90 kg / 198 lb

Width 60 cm / 23.6" 67.5 cm / 26.6"

Depth 65 cm / 25.6" 75 cm / 29.5"

Dimensions and weight
(with Cover) Height
50 cm / 19.7" / 85 cm / 33.5" 58.2 cm / 22.9" / 90 cm / 35.4"
(cover closed/open)

Weight 58 kg / 128 lbs 98 kg / 216 lb

Struers' equipment is in conformity with the provisions of the applicable International Directives and their appurtenant Standards (please contact you local supplier for details).

Struers' products are subject to constant product development. Therefore, we reserve the right to introduce changes in our products without notice.

8
SPECIFICATIONS Cat.no
Tegramin-30
Automatic, microprocessor controlled machine for grinding and polishing of specimens on 300 mm
MD-Disc with cone. Dosing modules, MD-Disc with cone and specimen holders are ordered separately. 06036127

Tegramin-30 with cover

Automatic, microprocessor controlled machine for grinding and polishing of specimens on 300 mm MD-Disc with
cone. With transparent cover. Dosing modules, MD-Disc with cone and specimen holders are ordered separately. 06036227

Tegramin-25
Automatic, microprocessor controlled machine for grinding and polishing of specimens on 250 mm
MD-Disc with cone. Dosing modules, MD-Disc with cone and specimen holders are ordered separately. 06026127

Tegramin-25 with cover

Automatic, microprocessor controlled machine for grinding and polishing of specimens on 250 mm MD-Disc with
cone. With transparent cover. Dosing modules, MD-Disc with cone and specimen holders are ordered separately. 06026227

Tegramin-20
Automatic, microprocessor- controlled machine for grinding and polishing of specimens on 200 mm
MD-Disc with cone. Dosing modules, MD-Disc with cone and specimen holder's are ordered separately. 06016127

Tegramin-20 with cover

Automatic, microprocessor- controlled machine for grinding and polishing of specimens on 200 mm
MD-Disc with cone. With transparent cover. Dosing modules, MD-Disc with cone and specimen 06016227
holder's are ordered separately.

Tegramin Dosing Module with 1 DP pump

To be installed on Tegramin-30 / -25 or -20. With one pump for diamond suspensions or lubricants. 06036900

Tegramin Dosing Module with 2 DP pumps

To be installed on Tegramin-30 / -25 or -20. With two pumps for diamond suspensions or lubricants. 06036901
Lavamin - Fully automatic
Tegramin Dosing Module with 2 DP and 1 OP pump
To be installed on Tegramin-30 / -25 or -20. With two pumps for diamond suspensions or lubricants
cleaning unit
and one pump for OP suspensions. 06036902 You save time with a faster cleaning process
Lavamin and the opportunity to change the preparation
Specimen cleaning unit for cleaning of specimen holders up to 160 mm dia. and for individual specimens
in specimen mover plates for Tegramin-25, -30, TegraForce-5 and RotoForce-4. 06236133 surface while the specimens are being clea-
Bottle tray for Tegramin. With space for six ½ l bottles and one 1l bottle. To be used with Tegramin-30 / -25 or -20. 06036910
ned. Automated cleaning perfection every
time and avoid replacement of preparation
Preparation Discs MD-Disc with cone for Tegramin-30, 300 mm dia. 06086403
MD-Disc with cone for Tegramin-25, 250 mm dia. 06086402 surfaces due to accidental contamination. In
MD-Disc with cone for Tegramin-20, 200 mm dia 06086401
addition to saving you time and costs, Lava-
Cover Transparent cover for Tegramin-25/-30 06036903 min eliminates chemical cleaning agents and
Transparent cover for Tegramin-20 06016903
leaves no environmental footprint.
Lid For Tegramin-25 and Tegramin-30 06036906
For Tegramin-20 06016906

Splash guard For Tegramin-30 06036905

for manual preparation
For Tegramin-25 06026905
For Tegramin-20 06016905

Disposable bowl liner For Tegramin-25 / -30. 5 pcs. 49900052

For Tegramin-20. 5 pcs. 49900056

Shift valve for Tegramin For recirculation cooling unit (05766xxx) or drain. 06036904

Struers Cooling Unit, System 3. With 50 l tank, small pump, Cooli-1, 50 l static filter with filter paper.
1 x 100 V / 50 Hz 05766516
1 x 220-240 V / 50 Hz 05766522
1 x 100-120 V / 60 Hz 05766523
1 x 220-240 V / 60 Hz 05766524
1 x 100-120 V / 50-60 Hz CSA 05766616

Levelling device. For levelling of specimens in specimen holders (ø 140 mm) 05256903

Levelling device, Uniforce. For levelling of specimens in specimen holders ø 140, 160 and 200 mm. 04886101
With pressure foot for positioning of specimens 04886102

Coupling For Tegramin-30 and Tegramin-25 specimen mover plates. 06086901

For Tegramin-20 specimen mover plates. 06086900

Specimen mover plates, for individual specimens

For Tegramin-25 For Tegramin-30
Without holes 06086906 06086936
For 6 specimens 25 mm dia. 06086902 06086932 A wide range of specimen mover plates are available
For 6 specimens 1" dia. 06086909 06086939
For 6 specimens 30 mm dia. 06086903 06086933
for Tegramin.
For 6 specimens 1¼" dia. 06086910 06086940
For 6 specimens 1½" dia. 06086911 06086941
For 6 specimens 40 mm dia. 06086904 06086934
For 3 specimens 50 mm dia. 06086905 -
For 3 specimens 2" dia. 06086943 -
For 6 specimens 50 mm dia. - 06086935
For 6 specimens 2" dia. 06086942
For 6 specimens 20 x 30 mm - 06086944
For Accustop 30 06086907 06086937
For Accustop 40 + TYNDS - 06086938

Specimen mover plates for Tegramin-20, for individual specimens

Without holdes 06086918
For 4 x 25 mm dia. 06086912
For 4 x 30 mm dia. 06086913
For 4 x 40 mm dia 06086914
For 4 x 1" dia. 06086915
For 4 x 1¼" dia. 06086916
For 4 x 1½" dia. 06086917