Samsung s16b Chassis Cw21m163nfxxec

COLOR TELEVISION RECEIVER
Chassis : S16B(P)_GREEN-3
Model : CW21M163NFXXEC
SERVICE Manual
COLOR TELEVISION RECEIVER FEATURES
■ AK CRT
■Multi Wide System
■ LNA Plus(Low Noise Amplifier)
■Turbo Plus
■ Low Stand-By Power Wattage
■ SOUND Equalizer
CW-21M163N
ELECTRONICS
This Service Manual is a property of Samsung Electronics Co.,Ltd. © Samsung Electronics Co., Ltd. Jul. 2005
Any unauthorized use of Manual can be punished under applicable Printed in Korea
International and/or domestic law.
AA82-02761A
Table of Contents
Chapter 1 Precaution
■ 1-1 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
■ 1-2 Servicing Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
■ 1-3 Static Electricity Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
■ 1-4 Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Chapter 2 Product Specification

■ 2-1 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
■ 2-2 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
■ 2-3 Specifications Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
■ 2-4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Chapter 3 Alignment & Adjustment

■ 3-1 Service Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
■ 3-2 How to Access Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
■ 3-3 Factory Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
■ 3-4 Service Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
■ 3-5 Software Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
■ 3-6 Replacements & Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Chapter 4 Exploded View & Part List

■ 4-1 CW21M163NFXXEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Chapter 5 Electrical Part List

■ 5-1 CW21M163NFXXEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Chapter 6 Troubleshooting
■ 6-1 Checkpoints by Error Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
■ 6-2 Trouble-shooting with New Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
■ 6-3 Troubleshooting Procedures by Error Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Chapter 7 Block Diagram

■ 7-1 Overall Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
■ 7-2 Partial Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Chapter 8 Wiring Diagram

■ 8-1 Overall Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Samsung Electronics
Chapter 9 PCB Diagram
■ 9-1 Main Baord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
■ 9-2 CRT Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Chapter 10 Schematic Diagram

■ 10-1 UOC3 & TUNER BLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
■ 10-2 POWER & DEF & CRT BLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
■ 10-3 SOUND AMP & SCART BLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
Chapter 11 Operation Instruction & Installation

■ 11-1 Product Features and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
Chapter 12 Disassembly & Reassembly

■ 12-1 Overhaul Disassembly & Reassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1
Chapter 13 Circuit Description

■ 13-1 Circuit Key Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1
Chapter 14 Reference Information

■ 14-1 Other issues related to other products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
■ 14-2 Technical Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3
Samsung Electronics
Precaution
1. Precaution
To avoid possible damages or electric shocks or exposure to radiation, follow the instructions below with regard to safety,
installation, service and ESD.
1-1 Safety Precautions

1. Make sure all protective devices are properly installed 5. Warning for Engineering Changes:
including non-metallic handles and compartment covers Never make any changes or additions to the circuit
when installing or re-installing the chassis or chassis design or the internal part for this product.
assemblies. Ex: Do not add any audio or video accessory
connectors. This might cause physical damage.
2. Make sure that no gaps exist between the cabinets for Furthermore, any changes or additions to the original
children to insert their fingers in to prevent children from design/engineering will invalidate the warranty.
receiving electric shocks. Gaps mentioned above include
ventilation holes of a too great magnitude between the 6. Warning - Hot Chassis:
vaccum tube and the cabinet mask, and the improper Some TV chassis are directly connected to one end of
installation of the rear cabinet. the AC power cord for electrical reasons.
Without insulated transformers, the product can only be
Errors may occur when the resistance is below 1.0 ㏁ or repaired safely when the chassis is connected to the
over 5.2 ㏁. earthed end of the AC power source.
In these cases, make sure that the device is repaired
before sending it back to the customer. To make sure the AC power cord is properly connected,
follow the instructions below. Use the voltmeter to
3. Check for Electricity Leakage (Figure 1-1) measure the voltage between the chassis and the
Warning: Do not use an insulated transformer for check- earthed ground. If the measurement is over 1.0V, unplug
ing the leakage. Use only those current leakage testers the AC power cord and change the polarity before re-
or mirroring systems that comply with ANSIC 101.1 and inserting it. Measure the voltage between the chassis
the Underwriter Laboratory's specifications (UL1410, and the ground again.
59.7).
7. Some TV chassis are shipped with an additional
secondary grounding system. The secondary system is
(READING SHOULD adjacent to the AC power line. These two grounding
LEAKAGE NOT BE ABOVE
0.5mA)
systems are separated in the circuit using an
DEVICE CURRENT
UNDER TESTER unbreakable/unchangeable insulation material.
TEST
TEST ALL
EXPOSED METAL 8. When any parts, material or wiring appear overheated or
SURFACES
damaged, replace them with new regular ones
2-WIRE CORD immediately. When any damage or overheating is
ALSO TEST WITH detected, correct this immediately and make a regular
PLUG REVERSED
(USING AC ADAPTER EARTH
check of possible errors.
PLUG AS REQUIRED) GROUND
9. Check for the original shape of the lead, especially that
Fig. 1-1 AC Leakage Test of the antenna wiring, any sharp edges, the AC power
and the high voltage power. Carefully check if the wiring
4. A high voltage is maintained within the specified limits is too tight, incorrectly placed or loose. Never change the
using safety parts, calibration and tolerances. When space between the part and the printed circuit board.
voltage exceeds the specified limits, check each special Check the AC power cord for possible damages. Keep
part. the part or the lead away from any heat-emitting
materials.
Samsung Electronics 1-1

Precaution
10. Safety Indication:

Some electrical circuits or device related materials
require special attention to their safety features, which
cannot be viewed by the naked eye. If an original part is
replaced with another irregular one, the safety or
protective features will be lost even if the new one has a
higher voltage or more watts.
Critical safety parts should be bracketed with ( ! ).

Use only regular parts for replacements (in particular,
flame resistance and dielectric strength specifications).
Irregular parts or materials may cause electric shock or
fire.
1-2 Samsung Electronics

Precaution
1-2 Servicing Precautions

Warning 1: First carefully read the "Safety Instruction" in this service manual.
When there is a conflict between the service and the safety instructions, follow the safety instruction at all times.
Warning 2: Any electrolytic capacitor with the wrong polarity will explode.
1. The service instructions are printed on the cabinet, and 6. Insulation Check Process: Unplug the power cord from
should be followed by any service personnel. the AC source and turn the switch on. Connect the insu-
lating resistance meter (500v) to the AC plug blade.
2. Make sure to unplug the AC power cord from the power
source before starting any repairs. The insulating resistance between the blade of the AC
(a) Remove or re-install parts or assemblies. plug and that of the conductive material should be more
(b) Disconnect the electric plug or connector, if any. than 1 ㏁.
(c) Connect the test part in parallel with the electrolytic
capacitor. 7. Any B+ interlock should not be damaged.
If the metal heat sink is not properly installed, no
3. Some parts are placed at a higher position than the connection to the AC power should be made.
printed board. Insulated tubes or tapes are used for this
purpose. The internal wiring is clamped using buckles to 8. Make sure the grounding lead of the tester is connected
avoid contact with heat emitting parts. These parts are to the chassis ground before connecting to the positive
installed back to their original position. lead. The ground lead of the tester should be removed
last.
4. After the repair, make sure to check if the screws, parts
or cables are properly installed. Make sure no damage is 9. Beware of risks of any current leakage coming into
caused to the repaired part and its surroundings. contact with the high-capacity capacitor.
5. Check for insulation between the blade of the AC plug 10. The sharp edges of the metal material may cause
and that of any conductive materials (i.e. the metal physical damage, so ensure wearing protective gloves
panel, input terminal, earphone jack, etc). during the repair.

Precaution
1-3 Static Electricity Precautions

1. Some semi-conductive ("solid state") devices are 6. Use only anti-static solder removal devices.
vulnerable to static electricity. These devices are known Most solder removal devices do not support an
as ESD. ESD includes the integrated circuit and the field anti-static feature. A solder removal device without an
effect transistor. To avoid any materials damage from anti-static feature can store enough static electricity to
electrostatic shock, follow the instructions described cause damage to the ESD.
below.
7. Do not remove the ESD from the protective box until the
2. Remove any static electricity from your body by replacement is ready. Most ESD replacements are
connecting the earth ground before handling any covered with lead, which will cause a short to the entire
semi-conductive parts or ass'ys. Alternatively, wear a unit due to the conductive foam, aluminum foil or other
dischargeable wrist-belt. conductive materials.
(Make sure to remove any static electricity before
connecting the power source - this is a safety instruction 8. Remove the protective material from the ESD
for avoiding electric shock) replacement lead immediately after connecting it to the
chassis or circuit ass'y.
3. Remove the ESD ass'y and place it on a conductive
surface such as aluminum foil to prevent accumulating 9. Take extreme caution in handling any uncovered ESD
static electricity. replacements. Actions such as brushing clothes or lifting
your leg from the carpet floor can generate enough static
4. Do not use any Freon-based chemicals. electricity to damage the ESD.
Such chemicals will generate static electricity that
causes damage to the ESD.
5. Use only grounded-tip irons for soldering purposes.
CAUTION
These servicing instructions are for use by

qualified service personnel only.
To reduce the risk of electric shock do not
perform any servicing other than that contained in the
operating instructions unless you are qualified to do so.

Precaution
1-4 Installation Precautions

1. For safety reasons, more than two people are required 6. Keep the antenna far away from any high-voltage cables
for carrying the product. and install it firmly. Contact with the high-voltage cable or
the antenna falling over may cause fire or electric shock.
2. Keep the power cord away from any heat emitting
devices, as a melted covering may cause fire or electric 7. Check the basics of the screen test.
shock. - Image position/size, Tilt adjustment
3. Do not place the product in areas with poor ventilation

such as a bookshelf or closet. The increased internal
temperature may cause fire.
4. Bend the external antenna cable when connecting it to

the product. This is a measure to protect it from being
exposed to moisture. Otherwise, it may cause a fire or
electric shock.
5. Make sure to turn the power off and unplug the power
cord from the outlet before repositioning the product.
Also check the antenna cable or the external connectors
if they are fully unplugged. Damage to the cord may
cause fire or electric shock.

MEMO

Product Specification
2. Product Specification
2-1 Product Features
BLOCK Specification Core Parts Remark
21" FLAT AK CRT AA91-09169B
CRT 17" FLAT AK CRT AA91-07348G
15" FLAT MST CRT AA91-07346R
AA40-00025A TDQ-6F/125S,NON-LNA
RF Part LNA & F/S TUNER
AA40-10007A TDQ-6L/125S,LNA
WORLD WIDE INPUT VOLTAGE RANGE
Power AA96-00242D 5Q0765RTH
STD-BY : 5W UNDER
- MULTI SYSTEM (NTSC/PAL/SECAM)
VIDEO AA09-00503A TDA12025PQ/N1F80
- 4H Comb Filter
- Output : 5W X2
- Function : NICAM/A2 STEREO, AA09-00503A TDA12025PQ/N1F80
SOUND
PSEUDO STEREO,V-DOLBY AA96-00244G TDA8944J
TURBO PLUS
Cabinet - 21"/17"/15" All CABINET
- BASIC MODEL : CW21M163NF
Other - UOC3 with a built-in MSP
- TURBO→ TURBO PLUS
■ Core Parts Function

- TDA12025PQ/N1F80 : Video/Sound Processing and MICOM
- 5Q0765RTH : SMPS Power STR
- TDA8944J : 5W Sound Output BTL AMP
- 24C16 : 16K EEPROM
- LA78040N : Vertical Deflection AMP
- ST2001HI : H-OUT S/W TR
- TDQ-6F(or 6L) : F/S PAL Tuner(LNA Option)
- TDA6109JF : R/G/B Drive AMP IC

2-2 Key Features

Chassis S16B Remark
Country EU CIS
ORIGIN MARK MADE IN HUNGARY MADE IN CHINA
COLOR PAL-BG / DK / I / NT4.43 PAL-BG / DK / I
demodulation SECAM-L / L' NTSC-M (CS SYSTEM)
Sound
QSS (Quasi Split) QSS (Quasi Split)
receving way
Sound
INTER CARRIER (Virtual Dolby / Nicam / A2 Stereo)
demodulation
Fixed Antenna 75ohm Din-Jack
Channel search F/S
CHANNEL numbers AIR (100Ch)
Input voltage AC 220V ~ 240V AC 160V - 300V
Power frequency 50HZ 50HZ
Power SYSTEM 5Q0765RTH
Power insulation SMPS / COLD
VHF LOW : 2 ~ 4
VHF HIGH : 5 ~ 12
receving(P/G) CH
UHF : 21 ~ 69
CATV : S1 ~ 41, X, Y, Z, Z+1, Z+2
Unfixed
BRAND / BUYER SAMSUNG / SAMSUNG
Safety EMI, EMS EMI, GOST(CIS)
Power cord/polarity CP2(4.0 Ø ) / NO, AP2 / YES, EP2 / NO
Character TTX TTX, LNA+

INCH 21" FLAT 17" FLAT 15" FLAT

CABINET(MODEL) CW21M16 / CS21M16 CS17A11 CS15M16
CABINET FRONT HIPS-HB HIPS-HB HIPS-HB
BACK HIPS-V2 HIPS-V2 HIPS-V2
REMOCON TYPE TM75 (36KEY) TM75 (36KEY) TM75 (36KEY)
REMOCON
Battery AAA AAA AAA
Weight
SET(Kg) 22.5 KG 14.6 KG 13.5 KG
(KG)
Length SET:W*D*H(mm) 590 X 492 X 464 494 X 417 X 391 -
(MM) Packing:W*D*H(mm) 675 X 595 X 580 572 X 497 X 470 512 X 466 X 445
CRT A51QDX993X(A)
Picture Scan 50Hz 50Hz 50Hz
Comb filter 4H Comb 4H Comb 4H Comb
Speaker Direct Direct Direct
Max output(Main) 5W x2 5W x2 5W x2
Sound Max output(Woofer) X X X
Equalizer O O O
Stereo Nicam Stereo Nicam Stereo Nicam Stereo
TTX/ CAPTION 10Page TTX 10Page TTX 10Page TTX
Game X X X
Etc Plug &?Play O O O
Demonstration O O O
Absent Power Off O O O
1. Scart Jack In / Out 1EA
External Jack 2. AV : Side Input 1EA
3. Earphone : Side 1EA
Panel key 6 6 6
Head / Ear Phone O (Cabinet Diff) O (Cabinet Diff) O (Cabinet Diff)
* Melody on/off * Melody on/off * Melody on/off
* Turbo Sound * Turbo Sound * Turbo Sound
* Auto Volume * Auto Volume * Auto Volume
Character
* Pre-Ch' * Pre-Ch' * Pre-Ch'
* LNA+ (Option) * LNA+ (Option) * LNA+ (Option)
* Led : Green * Led : Green * Led : Green

2-3 Specifications Analysis
Model CS-21M20 CW-21M163NF

Chassis KS9A S16B
Design
Product Type FLAT CRT FLAT CRT

Digital Display - -
Basic
Screen Size 21 21
Aspect Ratio 4:3 4:3
Broadcasting System PAL/SECAM PAL/SECAM
System Tuner Programmable F/S Programmable F/S
CH Memory 100CH 100CH
Supply 230V 230V
Power Stand-by 5W 5W
Picture ON Master S/W Master S/W
Comb-Filter 1H 4H
SCAN 50HZ 50HZ
Sharpness O O
LNA X (CIS : LNA PLUS) X
CTI X X
VM X X
AKB O O
Picture
P.STD O O
PIP X X
Digital NR O O
Color Tone(W/B) O O
Black Level Expantion O O
Screen Mode 5 Mode 5 Mode
3:2 / 2:2 Pull-Down X X
SPK System Direct Direct
Sound Output Power(Max) 5W + 5W 5W + 5W
Pseudo (Excet Mono type) O O
MDB X X
Virtual Dolby O O
MSE X X
Sound
Melody O O
Turbo Sound O O
A2 Stereo A2 or Nicam A2 or Nicam
Auto Stereo O O
AVL O O
Equalizer O O
Front/Side AV Jack O O
PC Input(VGA) X X
Scart Jack 1Scart 1Scart
Back A/V Monitor Out O O
Jack
S-VHS Jack(Front only) X X
Head/Earphone Jack O O
Common Interface O O
Service Port X X
I/B O O
Normal Remocon(TM75) O O
Accessory Battery O O
Matching Trans O O
Rod ANT O O

2-4 Accessories
Accessories Item Item code Remark
AA68-03621A
User Manual
(Eng)
Supplied Accessories
Remote Control /
AA59-00312J/ Samsung Service center
Alkaline Battery
4301-000121
(1.5V AAA)2EA
Warranty Card BN68-00514B
Coaxial Cable -
HDMI/DVI Cable -
Accessories that can be purchased
HDMI Cable -
additionally
Video/Audio Cable - Internal shopping mall
S-Video Cable -
-
Component Cable
Optical Cable -

MEMO

Alignment & Adjustment
3. Alignment & Adjustment

3-1 Service Instruction
1. General Adjustment :
In general, a color TV can provide ideal visual quality by adjusting the basic settings such as the vertical size, horizontal size,
focus, etc.
Display a black and white picture on the screen to check if the picture is clearly displayed.
If there are some 'spotted' points on the screen when displaying a black and white picture, degauss the screen using the
degauss coil. If the spotted points remain, re-adjust the purity and the convergence.
This completes the basic performance examination.
Notice.
■ These adjustments and the check list are only applied to S16B chassis-applied models.
■ Only use 230V for the measurement set. It is recommended using an insulation transformer when supplying power to
the set so as to prevent shock to the set or to yourself.
■ These adjustment specifications have been created on the basis of the domestic S16B chassis-applied remote control
model. Some of the contents may be changed subject to the sales location and the product specifications.
※When replacing the Module Service Instruction
1. When replacing the MAIN Board : Tilt adjustment, Focus adjustment, Screen voltage, W/B adjustment are all required. Since
the settings including the Channel information,Deflection, etc. are saved to the EEPROM,
recogfigure these settings when replacing the MAIN Board.
The notation of the software information : T-GRN2PEU-1007 refer to " GREEN2(S16A) / GREEN3(S16B) MODEL
EUROPE & CIS.
Since the settings including the Channel information, Deflection, etc. are
saved to the EEPROM, recogfigure these settings when replacing the MAIN Board.
2. When replacing the CRT Ass'y : No adjustments required
3. When replacing the front panel Master Power switch : No adjustments required
4. When replacing the Side AV Ass'y : No adjustments required
5. When replacing the Control Ass'y : No adjustments required
6. When replacing the PFC Ass'y : No adjustments required

3-2 How to Access Service Mode

1. To enter Service Mode, press the keys on the remote control according to the following sequence. (in Stand-by status)
Info → Menu → Mute → Power On
※ When failing to enter Service Mode, repeat the procedure above.
2. The initial screen of Service Mode.
Option1 XX XX XX XX XX
Option2
Deflection
WSS Deflection
Video Adjust1
Video Adjust2
Video Adjust3
Video Adjust4
Video Adjust5
YC Delay
Others
Bus Stop Off
CHECKSUM 0000
G2 Adjust
RESET
T-GRN2PEU-1000 2005/0X/XX
3. Functions of the Keys within Service Mode.

MENU Show all menus
▲ /▼ Move the cursor to select an item.
◀/▶ Adjust the selected configuration value
4. W/B Setting
No Item Data Required Adjustment
White x:272± 3 y:270± 3 Y:50± 3
1 White Balance (Standard Data)
Balance x:265± 3 y:266± 3 Y:2.0± .3
Toshiba Pattern
2 Screen Voltage Same as KS9A Basic Model
G2 Adjust

3-3 Factory Data ★ The underlined are items applied during the service adjustment. None of the others should be adjusted.
1.Option 1
"CIS 21"
"EU 21"
"AK-CRT/Non-PIP/LNA"
"AK-CRT/Non-PIP/Non-LNA"
CS21M16 "CIS 17" "CIS 15"
CW21M16
Item CS21K30 "AK-CRT/Non-PIP/LNA" "CRT/Non-PIP/LNA"
No CW21M02
CS21M20 CS17A11 CS15M16
CW21M06
CS21M20
CW21M20
CS21M21
Option 22 45 09 00 8C 22 E5 09 0F 8C 22 E5 09 0F 8C 22 E5 09 0F 8C
1 Video Mute 900msec 900msec 900msec 900msec
2 System CW CS CS CS
3 AV Jack 1SCART 1SCART 1SCART 1SCART
4 CRT 4:3 Zoom 4:3 Zoom 4:3 Zoom 4:3 Zoom
5 Sound NICAM NICAM NICAM NICAM
6 Volume Curve Large Large Large Large
7 Initial Lang. English Russia Russia Russia
8 TTX Osd Language Osd Language Osd Language Osd Language
9 TTX Flof/List Flof Flof Flof Flof
10 Tilt Off Off Off Off
11 LNA Off On On On
12 DNIe JR Off Off Off Off
13 Hotel Mode Off Off Off Off
14 PIP Off Off Off Off
2. Option 2
"CIS 21"
"EU 21"
"AK-CRT/Non-PIP/LNA"
"AK-CRT/Non-PIP/Non-LNA"
CS21M16 "CIS 17" "CIS 15"
CW21M16
Item CS21K30 "AK-CRT/Non-PIP/LNA" "CRT/Non-PIP/LNA"
No CW21M02
CS21M20 CS17A11 CS15M16
CW21M06
CS21M20
CW21M20
CS21M21
Option 22 45 09 00 8C 22 E5 09 0F 8C 22 E5 09 0F 8C 22 E5 09 0F 8C
1 X-Ray Protect Off Off Off Off
2 High Deviation Off Off Off Off
3 V-Guard On On On On
4 Sound Carrier Mute Off Off Off Off
5 TTX TOP Mode Off Off Off Off
6 Speaker 5W 5W 5W 5W

3.Deflection
"EU 21" "CIS 21"
"AK-CRT/Non- "AK-CRT/Non
"CIS 17" "CIS 15"
PIP/Non-LNA PIP/LNA TUNER"
"AK-CRT/Non- "CRT/Non-PIP/LNA
TUNER" CS21M16
No Item PIP/LNA TUNER" TUNER" Fix/Adj Remarks
CW21M16 CS21K30
CS17A11 CS15M16
CW21M02 CS21M20
CW21M06 CS21M20
CW21M20 CS21M21
1 V Amp 32 32 32 32 Adjust
2 V Shift 32 32 32 32 Adjust
3 H EW 32 32 32 32 FIX
4 H Shift 32 32 32 32 Adjust
5 V Linearity 40 40 40 40 FIX
6 V S-Correction 28 28 28 28 FIX
7 V Slope 25 25 25 25 FIX
8 V Scroll 34 34 34 34 FIX 32→34
9 V Zoom 50 50 50 50 FIX 45→50
10 H Parabola 32 32 32 32 FIX
11 Upper Corner 32 32 32 32 FIX
12 Lower Corner 32 32 32 32 FIX
13 H Trapezium 32 32 32 32 FIX
14 Bow 32 32 32 32 FIX
15 Angle 32 32 32 32 FIX
4 WSS Deflection
"EU 21" "CIS 21"
"AK-CRT/Non- "AK-CRT/Non-
"CIS 17" "CIS 15"
PIP/Non-LNA PIP/LNA TUNER"
"AK-CRT/Non- "CRT/Non-PIP/LNA
TUNER" CS21M16
No Item PIP/LNA TUNER" TUNER" Fix/Adj Remarks
CW21M16 CS21K30
CS17A11 CS15M16
CW21M02 CS21M20
CW21M06 CS21M20
CW21M20 CS21M21
1 16:9 V Amp 32 32 32 32 FIX

2 16:9 V Shift 32 32 32 32 FIX
3 16:9 H Parabola 32 32 32 32 FIX
4 16:9 H Trapezium 32 32 32 32 FIX
5 14:9 V Amp 32 32 32 32 FIX
6 14:9 V Shift 32 32 32 32 FIX
7 14:9 H Parabola 32 32 32 32 FIX
8 14:9 H Trapezium 32 32 32 32 FIX
9 VM Mode 0 0 0 0 FIX
10 VM Gain 0 0 0 0 FIX
11 VM Delay 5 5 5 5 FIX
12 Preset Gain R 20 20 20 20 FIX 35→ 20
13 Preset Gain G 20 20 20 20 FIX 35→ 20
14 Preset Gain B 20 20 20 20 FIX 35→ 20


5. Video Adjust 1~5

＊Video Adjust 1
"EU 21" "CIS 21"
PIP/Non-LNA PIP/LNA TUNER" "CIS 17" "CIS 15"
TUNER" CS21M16 "AK-CRT/Non- "CRT/Non-
No Item Fix/Adj Remarks
CW21M16 CS21K30 PIP/LNA TUNER" PIP/LNA TUNER"
CW21M02 CS21M20 CS17A11 CS15M16
CW21M06 CS21M20
CW21M20 CS21M21
1 R Cutoff 32 32 32 32 Adjust
2 B Cutoff 32 32 32 32 Adjust
3 R Drive 32 32 32 32 Adjust
4 G Drive 32 32 32 32 FIX
5 B Drive 32 32 32 32 Adjust
6 Sub Bright 10 10 10 10 Adjust
7 Sub Contrast 10 10 10 10 Adjust
8 G2 Adjust Bright 48 48 48 48 FIX 42→48
9 AKB Option 0 0 0 0 FIX
10 Cathode Drive Level 6 6 3 3 FIX 3→6
11 TTX Bright 10 10 10 10 FIX
12 TTX RGB Bright 15 15 15 15 FIX
13 TTX Position 11 11 11 11 FIX 10→11
14 Turbo Center Frequency 2 2 2 2 FIX
15 Threshold Sound1 Carrier 25 25 25 25 FIX 4/11 add
＊Video Adjust 2
"EU 21" "CIS 21"
CW21M02 CS21M20 CS17A11 CS15M16
CW21M06 CS21M20
CW21M20 CS21M21
1 Melody Volume 35 35 35 35 FIX

2 PAL/SECAM Sub Color 12 12 12 12 FIX 15→12
3 NTSC Sub Color 5 5 5 5 FIX CIS: 10→5 (6/16)
4 NTSC Sub Tint 12 12 12 12 FIX CIS: 6→12 (6/16)
5 YUV Sub Tint RF 32 32 32 32 FIX
6 YUV Sub Tint AV 32 32 32 32 FIX 5/02 add
7 YUV Sub Tint RGB 32 32 32 32 FIX 5/02 add
8 Blue Stretch 1 1 1 1 FIX
9 Soft Clipping Level 0 0 0 0 FIX
10 Peak White Limit 15 15 15 15 FIX
11 SECAM B-Y Offset 1 1 1 1 FIX
12 Peakng CF0 & Delay Mode 3 3 3 3 FIX
13 Sub Sharpness-RF 15 15 15 15 FIX
14 Video Dependent Coring RF 1 1 1 1 FIX
15 Video Dependent Coring AV 0 0 0 0 FIX 5/02 add

＊Video Adjust 3
"EU 21" "CIS 21"
CW21M02 CS21M20 CS17A11 CS15M16
CW21M06 CS21M20
CW21M20 CS21M21
1 PIP Contrast 12 12 12 12 FIX

2 PIP Bright 15 15 15 15 FIX
3 PIP Tint 64 64 64 64 FIX
4 PIP Color 7 7 7 7 FIX
5 PIP YC Delay 11 11 11 11 FIX
6 PIP PAL V. Pos 7 7 7 7 FIX
7 PIP NTSC V. pos 7 7 7 7 FIX
8 PIP H. Pos 1 1 1 1 FIX
9 PIP R Cutoff 15 15 15 15 FIX
10 PIP G Cutoff 15 15 15 15 FIX
11 PIP B Cutoff 15 15 15 15 FIX
12 PIP R Drive 65 65 65 65 FIX
13 PIP G Drive 65 65 65 65 FIX
14 PIP B Drive 65 65 65 65 FIX
＊Video Adjust 4
"EU 21" "CIS 21"
CW21M02 CS21M20 CS17A11 CS15M16
CW21M06 CS21M20
CW21M20 CS21M21
1 IF Preset Value 1 32 32 32 32 FIX

2 IF Preset Value 2 32 32 32 32 FIX
3 IF PLL Osc Preset Value 0 0 0 0 FIX
4 DCXO Caps/NICAM Center 59 59 59 59 FIX 55→59
5 DCXO Scaling Control Gain 3 3 3 3 FIX
6 RF AGC 20 28 28 28 FIX CIS: 2→28 (7/04)
7 IF AGC Speed 1 1 1 1 FIX
8 IF Demodulator 38 38 38 38 FIX
9 Fast Filter IF PLL 0 0 0 0 FIX

＊Video Adjust 5
"EU 21" "CIS 21"
CW21M02 CS21M20 CS17A11 CS15M16
CW21M06 CS21M20
CW21M20 CS21M21
1 Bypass of Chroma Base Band 0 0 0 0 FIX
2 Fixed Beam Current 0 0 0 0 FIX
3 Fixed Beam Current1 0 0 0 0 FIX
4 Forced Colour On 0 0 0 0 FIX
5 Sync Performance Trick Mode 0 0 0 0 FIX
6 Beam Current Limiting 0 0 0 0 FIX
7 Comb Filter 0 0 0 0 FIX
8 Chroma Trap Mode 0 0 0 0 FIX
9 EHT Tracking Mode 1 1 1 1 FIX
6. YC Delay
"EU 21" "CIS 21"
CW21M02 CS21M20 CS17A11 CS15M16
CW21M06 CS21M20
CW21M20 CS21M21
1 PAL Delay 13 13 13 13 FIX
2 SECAM Delay 15 15 15 15 FIX
3 NTSC Delay 12 12 12 12 FIX
4 PAL AV Delay 13 13 13 13 FIX
5 SECAM AV Delay 15 15 15 15 FIX
6 NTSC AV Delay 12 12 12 12 FIX

7. Others
"EU 21" "CIS 21"
PIP/Non-LNA PIP/LNA TUNER" "CIS 17 "CIS 15"
TUNER" CS21M16 ""AK-CRT/Non- "CRT/Non-
CW21M02 CS21M20 CS17A11 CS15M16
CW21M06 CS21M20
CW21M20 CS21M21
1 Service Blanking 0 0 0 0 FIX
2 High Current Level 1 1 1 1 FIX
3 Black Area 2 2 2 2 FIX
4 Black Stretch 2 2 2 2 FIX
5 OSD Brightness 15 15 15 15 FIX
6 PWL Active 1 1 1 1 FIX
7 Bypass Peaking Delay 0 0 0 0 FIX
8 Ratio Pre & After Shoot 0 0 0 0 FIX
9 Ratio posi & Nega Peaks 0 0 0 0 FIX
10 Dynamic Skin 0 0 0 0 FIX
11 Gamma & White Stretch 1 1 1 1 FIX
12 PAL/NTSC Ident Sensitivity 1 1 1 1 FIX
13 Comb Filter Diode Clamp 1 1 1 1 FIX
14 DC Transfer Ratio 1 1 1 1 FIX
15 NTSC Metrix 0 0 0 0 FIX 6/03 Add
H 272/270 50fL 286/290 40fL 286/290 50fL 286/290 60fL

WHITE BALANCE
L 265/266 2.0fL 286/290 2.0fL 286/290 2.0fL 286/290 2.0fL

3-4 Service Adjustment

3-4-1 Adjusting the Picture Size
■ Since the S16B chassis has the deflection settings data within the Factory Data, the picture size has to be adjusted when
replacing the Main Board or the UOC3 IC, according to the following procedures.
① Display the Lion pattern. ② Press "Power Off →Info → Menu → Mute → Power On"
using the remote control and enter Factory Mode.
③ Enter Deflection Mode. ④ Adjust the V-AMP, V-SHIFT, H-AMP and H-SHIFT items so
that the width becomes 5 and the height becomes 4.
5 5

3-4-2 Adjusting the Picture Straight Lines
① Display the Cross Hatch pattern.
② Adjust settings other than V-AMP, V-SHIFT, H-AMP and H-SHIFT so that straight lines are displayed without curves.
③ Adjust BOW and the Angle settings so that the center line ④ Adjust the H-Parabola and H-Trapezium settings so that
becomes a straight line. the left and right lines become straight.
⑤ Adjust the Upper Corner and the Low Corner settings so that ⑥ Adjust the V-Linearity and V-SC settings so that the
the end of the lines become straight. intervals of the horizontal lines become uniform.
⑦ When the adjustments are complete, display the Lion pattern and check that the picture size has not been changed.
If there is no change, finish the adjustments.

3-5 Software Upgrade

3-5-1 Checking the Version of the Software (Analog SW)
1. To enter Service Mode, press the keys on the remote control according to the following sequence. (in Stand-by status)
Info → Menu → Mute → Power On
2. When entering Service mode, the software information is displayed at the top of the service mode menu OSD.
ex) T-GRN2PEU-1000 2005/0X/XX

3-5-2 Service Download Procedure

1. Double click the your desktop “WISP” icon.
2. Check the standard

- Check the appoint “Picasso N2”
- Check the “Flash selection” item is appoint “Manual”
- You can adjust program delay time for program speed
but we use the normal “5[ms]”
- Check the green lamp if this is sometime red lamp you can not programming

3. Check the IIC line

- Click the “Enter ISP Mode” button For IIC bus line problem or not
- Change the “Press Send to enter ISP Mode”
- Click the “Send” button
4. Erase before program

- Click the “Erase Flash” button for before program erase
- You can select flash selection item but we use normal “All” mode
- Change the “Select flash ROM to erase. When ready press Send.”

5. Write new program

- Click the “Write Flash” button for new program download
- Change the “Load.hex file to program flashes.”
- Click the “Browse” button and find the new program folder in your computer
6. Verify new program

- Click the “Verify Flash” button
- Change the “Select flash to verify correct programming.
When ready press Send.”

3-6 Replacements & Calibration

3-6-1 Adjusting the Focus
■ Since the S16B chassis has a built-in single focus circuit, take care when adjusting the focus. When the CRT PCB, FBT or
CRT has been replaced, the focus has to be adjusted according to the following procedures.
1. Display the Cross Hatch pattern.
2. Set the Screen Adjustment to "Standard".
3. Turn the Static Focus VR clockwise to the maximum position.

(End of clockwise direction)
4. Slowly turn the Static Focus VR counter clockwise so that the center vertical line
is the most clearly displayed. [adjusted point : Center(2/1)]
SINGLE
FOCUS VR
5. Check the entire screen focus and repeat steps 3 to 4, if necessary.

3-6-2 Adjusting the Screen Voltage
1. Select "Power Off →Info → Menu → Mute → Power On" to enter Service Mode.
2. Initialize all settings to the values appropriate to the corresponding model.
3. Display the Toshiba pattern.
4. First check IBRM in "G2 Adjust" of Factory and adjust Screen VR until the color of IBRM item turns green.
SCREEN
VR

3-6-3 Adjusting the White Balance
1. Select "Info → Menu → Mute → Power On" to enter Service Mode.
2. Initialize all settings to the values appropriate to the corresponding model.
3. Display the Toshiba pattern and adjust the White Balance using CA100 with the coordinates of the corresponding model.
4. Enter Video Adjust1 of Service Mode. Adjust Low/Light.

- Adjust Sub Bright to set Y.
- Adjust B Cutoff to set y.
- Adjust R Cutoff to set x.
5. Enter Video Adjust1 of Service Mode. Adjust High/Light.

- Adjust Sub Contrast to set Y.
- Adjust B Drive to set y.
- Adjust R Drive to set x.
6. Check Low/Light and readjust it if its value has been changed.
7. If you have readjusted Low/Light, readjust High/Light until the two values are identical to the coordinates of the corresponding
model.
※ White Balance Standard Data
No Item Data Required Adjustment

White x:272± 3 y:270± 3 Y:50± 3
1 White Balance (Standard Data)
Balance x:265± 3 y:266± 3 Y:2.0± .3
3-6-4 Check List for the Screen Voltage and White Balance Adjustment
1. The Screen Voltage and White Balance are connected each other, and both of them have to be configured to the correct values.
2. Adjust the White Balance after the Screen Voltage was adjusted, and check if the Screen Voltage is normal after adjusting the
White Balance.
3. If the White Balance is readjusted, check the Screen Voltage again.
4. When the adjustment is finished, check the following checklist.

- If there is a spot on the screen when turning the TV set off/on, adjust the Screen Voltage again.
- If there is a ghost line on the screen, adjust the Screen Voltage again.

Troubleshooting
6. Troubleshooting
6-1 Checkpoints by Error Mode
■ Power LED: Check that the LED works when turning the Master Switch ON/OFF
■ LED Indicators: See table 6-2-1 Basic Troubleshooting: LED Diagnosis on the Front Panel.
■ In case of a power failure or abnormal screen, check the following items.
1) Check that the power cord is correctly connected to a 230V wall outlet.
2) Check that the Master Switch has been pressed.
3) Check that the transmitter is turned on.
4) Check that transmitter device selection is set to TV.
5) Check that the signal cable is properly connected.
6) Check that channel setting has been set.

Troubleshooting
6-1-1 Flow Chart for Malfunction
No Picture & No Sound
Check the AC
voltage impress
Check the master

switch on
Check the
Check the Yes Check the Yes Yes
IC801S #1 Check the others part
FUSE “FP801S” “D801S” #1
W6750F
Yes No No
Change “IC801S”
Change “FP801S” Change “D801S”
Yes
Compleat
Repair No Power
No picture & no sound

(1st power OK)
Yes Check the others

Check the +125V line
B+ line
No
“D811”(D811A) open Yes T444 B+ Pin #3 Yes Check the +125V line
and check Open and check others part
No No
Change the “D811” Yes

Check the “Q401”
(D811A)
No
Change the “Q401”
Compleat
repair no power

Troubleshooting
6-2 Troubleshooting Procedures by Error Modes

6-2-1 Basic Troubleshooting: Diagnosis of LED on the Front Panel
● : Light is On
◑ : Light is Blinking
○ : Light is Off
Power Description
○ This happens when the Master Switch is not pressed or the power cord is disconnected.
This happens when the power cord is connected and the power switch is pressed.
●
If you cannot set the power switch on by pressing it, check the power switch Ass'y.
If you press the power switch of the transmitter or the channel key on the remote control when in
St-BY status, the screen will be turned on.
○→◑→●
If the LED blinks and the screen is not displayed, check the connection between the Control
Assy and the Main Board.
6-2-2 Troubleshooting by the Checksum
■ Diagnosis of trouble by the checksum is neither reliable nor convenient.

You can only use the checksume of the current direct-view TV to determine whether the software is corrupted or not.
The Checksum value is determined according to the version of the software loaded on the set.
Therefore, you can determine whether the software has been properly downloaded, if you know the correct checksum for that
version of the software.
You can check the checksum according in the following order.

Factory Mode → Checksum → Right Button → Calculate Checksum → Output Checksum (e.g. 3036)
■ Checksum Examples
T-TR2PEU-1000 : checksum = 8036
T-TR2PEU-1010 : checksum = B612

Wiring Diagram
8. Wiring Diagram
8-1 Overall Wiring
RHF M@K Power Switch BNMSQNK
ONV DQ
ONV DQ NM.NEE Bnmsqnk Rhf m` k
@U L @HM
@U Rhf m` k @t chn Nt s
ROD@J DQ
BQS
CRT Power Supply
M ai n Input

MEMO

PCB Diagram
9. PCB Diagram
9-1 Main Board
9-1-1 Assy Main Board
GT301
CN701
CN602
GT801
CN902 CN901
■ The Board that Controls Various Signals & POWER Control
9-1-2 Names & Roles of Key Parts
* GT801 : A 3 pin port connected to the MASTER ASS'Y, which handles MASTER POWER ON/OFF.
* CN902 : A 4 pin port connected to the CONTROL ASSY, which delivers the necessary signal to KEY-IN1, KEY-IN2 CONTROL.
* CN901 : A 4 pin port connected to the CONTROL ASSY, which delivers the necessary signal to the remote control and the
LED CONTROL.
* CN602 : A 4 pin port connected to the SPEAKER port, which delivers the signal from the AMP to the speakers.
* CN701 : An 12 pin port connected to the AV ASS'y, which receives AV external input.

PCB Diagram
9-1-3 Main Board Connector Pin
CN901 CN902
Connected to the Control Ass'y Connected to the Control Ass'y
PIN No. Pin Name PIN No. Pin Name
1 VCC-5V(A) 1 KEY-IN1
2 GND 2 GND
3 STD-LED 3 KEY-IN3
4 IR
CN602 CN701
Connected to the Speaker Connected to the AV Ass'y
PIN No. Pin Name PIN No. Pin Name
1 R+ 1 V-OUT
2 R- 2 GND
3 L+ 3 V-IN
4 L- 4 GND
5 L-OUT
6 L-IN
7 R-OUT
8 R-IN
9 L-
10 L+
11 R-
12 R+

PCB Diagram
9-2 CRT Board

9-2-1 CRT Board
GT502
GT501
CN501A
9-2-2 Names & Roles of Key Parts
* GT501 & GT502 : The TBC-WIRE connection port. This port plays the role of the CRT GROUND.
* CN501A : The R/G/B output signal from the UOC IC, which is required to drive the CRT and the AMP, from the
DEFLECTION BLOCK is connected to this port.
9-2-3 CRT Board Connector Pin

CN501A
Connects the R/G/B signal from the UOC IC.
PIN No. Pin NAME
1 R-OUT
2 G-OUT
3 B-OUT
4 GND
5 FEED-BACK
6 GND
7 HEATER
8 NC
9 B+200V

MEMO

Operation Instruction & Installation
11. Operation Instruction & Installation

11-1 Product Features and Functions
11-1-1 Front
11-1-2 Rear

11-1-3 Side

11-1-4 Remote Control
POWER MUTE
Used to switch the TV Used to switch the
on and off. sound off temporarily. To
turn the sound back on,
Numeric buttons
press the MUTE , , or
Used to select channels
button.
directly.
/
-/--
Used to increase or
Used to select a channel
decrease the volume.
numbered ten or over.
Press this button, then TV
“-- ” symbol is Used to return to the TV
displayed. Enter the mode when it is in
two-digit channel external input mode.
number.
MENU P /
Used to display the on- Used to display the next
screen menu or return to or previous stored
the previous menu. channel.
/ / / INFO
Used to control the Used to view the
cursor in the menu. channel information and
setting status you
P.SIZE
selected.
Used to change the
screen size. EXIT
Used to exit from any
DUAL I -II
display or return to
Used to select the
normal viewing.
sound mode.
ENTER
TURBO
While using the on-
Used to select the turbo
screen menus, press the
sound option.
ENTER button to
S.MENU activate (or change) a
Used to display the particular item.
sound menu.
SLEEP
PRE-CH Used to select a preset
Used to switch time interval for
repeatedly between the automatic shut off.
last two channels
P.MODE
displayed.
Used to select the
VIDEO picture effect.
Used to display all of the
S.MODE
available video sources.
Used to select the
sound effect.

MEMO

Circuit Description
13. Circuit Description

13-1 Circuit Key Point
13-1-1 Pin configuration of “Face-down” QIP versions
13-1-2 UOC3(TDA120XX) Pin Description
Pi n Name Regi ster Port Type Ini ti al Descri pti on (Mi com Pi n 1 ~ 11, 54 ~ 64)
N
Noo
51 pTilt P0.0 Push Pull - Tilt
2 pIR P0.5 Open Drain - Remocon IR
4 pDcoil P1.0 Push Pull - Degaussing Coil
-NTSC/PAL S/W(PAL : High, NTSC3.58 : Low)
5 pSawFilter P1.1 Push Pull 1
-Europe CW L/ L' Sound S a w S/W (L' : High, L : Low)
- High : Power On
6 pPower P1.3 Push Pull 0
- Low : Power Off
7 pSCL P1.6 Push Pull 0 - I2C Bus Clock
8 pSDA P1.7 Push Pull 0 - I2C Bus Data
10 pLED P2.0 Push Pull 1 - Led(StandBy Mode, Remocon )
- High : Sound Mute On
11 pSoundMute P2.1 Push Pull 1
- Low : Sound Mute Off
- Scart1 ID
12 pScart1 P3.0 Open Drain
- China : Sound Saw Filter S/W(RCA Option Sound M : Low, High)
- Scart2 ID
13 pScart2 P3.1 Open Drain
- RCA Jack X-Ray
14 pBusStop P3.2 Open Drain 1 - Bus Stop Port
15 pPanelKey1 P3.3 Open Drain - Panel Key 1(Channel up, Channel Down, Volume Up, Volume Down, Menu)

Circuit Description
13-1-3 Control System Features
＊ 80C51 micro-controller core standard instruction set and timing

＊ 0.4883 ms machine cycle (6 clock cycles with 12.288 MHz derived from an xtal frequency of 24.576MHz)
＊ maximum 256k x 8-bit program ROM
＊ maximum of 8k x 8-bit auxiliary RAM
＊ auxiliary RAM page pointer
＊ 12-level interrupt controller for individual enable/disable with two level priority
＊ stand-by, idle and power-down modes
＊ watchdog timer
＊ two 16-bit timer/counters
＊ additional 24-bit timer (16-bit timer with 8-bit Pre-scaler)
＊ 16-bit data pointer
＊ five 6-bit pulse width modulator (PWM) outputs for control of TV analogue signals.
＊ one 14-bit PWM for voltage synthesis tuning control.
＊ 8-bit ADC with 4 multiplexed inputs.
＊ remote control pre-processor (RCP).
＊ I2C byte level bus interface.
＊ universal asynchronous receiver transmitter (UART)
＊ 24 General I/O.
13-1-4 Vertical Circuit (LA78045)
Feed back gain control for

vertical picture size also have
some connector vertical shift
Feed back gain control for

vertical picture size also have
some connector vertical shift

Circuit Description
13-1-5 Power IC (STR-W6750F)
AC input low voltage

Circuit Description
13-1-6 TDA6109JF

Circuit Description
13-1-7 CRT Drive
13-1-8 Spot Killer

MEMO

Reference Information
14. Reference Information

14-1 Other issues related to other products
Problem Descriptions
Braun, PDP and LCD TVs can all be damaged. When a still image is displayed in a sequence,
this can leave stains or after-images due to the characteristics of the panel.
A fixed screen can cause
However, the DLP TV has the advantage that no stains or after-images are left on the screen.
permanent damage to the TV
The DLP TV has mirror pixels on the DMD panel that project the beam onto the screen, in
Braun tube.
which the mirror is a digital representation of 0s and 1s, leaving no trace of light.
The mirror returns to a blank state so that no stains or after-images are left.
When a digitally distributed TV The digital distributed TV (Ready Technique) can render HD sources as HD-rated.
user receives HD-rated However, you need to install a set-top box for this purpose. The digital TV alone cannot render
broadcasts: HD broadcasting as HD-rated. Install the formal set-top box for HD broadcasts.
When a digital distributed TV
The digitally distributed TV (Ready Technique) renders any broadcasting service as SD-rated.
user selects normal size (4:3) to
However, when connected to a set-top box, the digital TV renders HD broadcasts as HD-rated
receive SD-rated digita
and renders SD as SD-rated. The screen size is scaled to 4:3.
broadcasts:

Reference Information
14-2 Technical Terms

Digital Broadcast Satellite Broadcast
Digital Broadcast is a television broadcasting signal digitized Satellite Broadcast transmits programs via satellite so that the
and transmitted according to the United States' terrestrial digital broadcast is viable in all areas at a high visual and sound quali-
broadcast standard, or ATSC. ty. It provides approximately 100 channels including public
broadcast channels. To view satellite broadcast, you have to
Mono install an additional receiver.
A type of audio interface that transmits audio signals through a
single channel. Wired Broadcast
Through a mono interface, it is hard to experience stereophonic Satellite Broadcast refers to movie, entertainment and educa-
sound and sound is played only by one speaker. tional programs transmitted by the broadcasting station in a
hotel or school.
Reception Sensitivity Amplification
A signal amplification technique that amplifies weak broadcast- Audio Multimix
ing signals by applying satellite technology to provide a better Audio Multimix provides 2 languages for audio when broadcast-
visual quality even for users in regions where only weak broad- ing a foreign movie, drama, news, etc. You can select and lis-
casting signals are available. ten to one of the supported languages or you can select and
listen to both languages simultaneously.
Stereo
A type of audio interface that transmits audio signals through 2 Component Port (Green, Blue, Red)
channels. The Component Port separately transmits the luminance signal
Stereo transmits audio signals for the right and left channels so and provides the best quality of all video connection types.
that you can experience stereophonic sound, and the sound is
played with 2 speakers. Cable Broadcast
Cable Broadcast transmits programs via cable instead of radio
Analog Broadcast wave. To view a cable broadcast, you need to subscribe to your
Analog Broadcast is a television broadcasting signal transmit- local cable broadcast service provider and install an additional
ted according to the NTSC standard. receiver.
ANTENNA IN Port Tuner

A port to connect the TV aerial using a coaxial cable. It is gen- A device that enables selecting a specific frequency for a chan-
erally used to watch public broadcast programs. nel on a TV or radio.
English Caption Anynet

A function that shows English caption or text information includ- Anynet is an AV network system that enables the easy-to-use
ed in the broadcasting signal or video tape. You can use this AV interface for users by controlling connected AV devices
function to study English by watching AFKN or CC marked through the Anynet menu when AV devices of Samsung
video tapes. Electronics are connected.
Video/Audio Ports DVD (Digital Versatile Disc)

You may experience poor visual and audio quality when watch- DVD is a large capacity media that can save multimedia con-
ing a video tape on channel 3 or 4 through the antenna cable. tent such as video, game, audio applications, etc. using MPEG-
You can experience better visual and audio quality connecting 2 video compression technology on a CD-sized disc.
the TV and VCR through the Video/Audio ports. The video port
is distinguished by the color yellow, and the audio ports are dis- S-VIDEO IN Port
tinguished by the white (left) and red colors (right). This is called super video. S-Video is a type of video signal
which has the video luminance and color signals separated in
External Input order to provide a better visual quality.
External Input is connecting video devices such as a VCR,
camcorder, DTV receiver, DVD, etc. as a video source. VHF/UHF
VHF refers to TV channels 2 to 13, and UHF refers to TV chan-
nels 14 to 69.

COLOR TELEVISION RECEIVER
Chassis : S16B(P)_GREEN-3
Model : CW21M163NFXXEC
SERVICE Manual
COLOR TELEVISION RECEIVER FEATURES
■ AK CRT
■Multi Wide System
■ LNA Plus(Low Noise Amplifier)
■Turbo Plus
■ Low Stand-By Power Wattage
■ SOUND Equalizer
CW-21M163N
ELECTRONICS
This Service Manual is a property of Samsung Electronics Co.,Ltd. © Samsung Electronics Co., Ltd. Jul. 2005
Any unauthorized use of Manual can be punished under applicable Printed in Korea
International and/or domestic law.
AA82-02761A
Table of Contents
Chapter 1 Precaution
■ 1-1 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
■ 1-2 Servicing Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
■ 1-3 Static Electricity Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
■ 1-4 Installation Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Chapter 2 Product Specification

■ 2-1 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
■ 2-2 Key Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
■ 2-3 Specifications Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
■ 2-4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
Chapter 3 Alignment & Adjustment

■ 3-1 Service Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
■ 3-2 How to Access Service Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
■ 3-3 Factory Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
■ 3-4 Service Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
■ 3-5 Software Upgrade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
■ 3-6 Replacements & Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
Chapter 4 Exploded View & Part List

■ 4-1 CW21M163NFXXEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Chapter 5 Electrical Part List

■ 5-1 CW21M163NFXXEC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
Chapter 6 Troubleshooting
■ 6-1 Checkpoints by Error Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
■ 6-2 Trouble-shooting with New Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
■ 6-3 Troubleshooting Procedures by Error Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Chapter 7 Block Diagram

■ 7-1 Overall Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
■ 7-2 Partial Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
Chapter 8 Wiring Diagram

■ 8-1 Overall Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
Samsung Electronics
Chapter 9 PCB Diagram
■ 9-1 Main Baord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
■ 9-2 CRT Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Chapter 10 Schematic Diagram

■ 10-1 UOC3 & TUNER BLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1
■ 10-2 POWER & DEF & CRT BLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
■ 10-3 SOUND AMP & SCART BLOCK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
Samsung Electronics

Samsung s16b Chassis Cw21m163nfxxec

Uploaded by

Copyright:

Available Formats

Samsung s16b Chassis Cw21m163nfxxec

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Samsung s16b Chassis Cw21m163nfxxec

Uploaded by

Copyright:

Available Formats

COLOR TELEVISION RECEIVER

COLOR TELEVISION RECEIVER FEATURES

■Multi Wide System

■ LNA Plus(Low Noise Amplifier)

■ Low Stand-By Power Wattage

Chapter 2 Product Specification

Chapter 3 Alignment & Adjustment

Chapter 4 Exploded View & Part List

Chapter 5 Electrical Part List

Chapter 7 Block Diagram

Chapter 8 Wiring Diagram

Chapter 10 Schematic Diagram

Chapter 11 Operation Instruction & Installation

Chapter 12 Disassembly & Reassembly

Chapter 13 Circuit Description

Chapter 14 Reference Information

1-1 Safety Precautions

Samsung Electronics 1-1

10. Safety Indication:

Critical safety parts should be bracketed with ( ! ).

1-2 Samsung Electronics

1-2 Servicing Precautions

Samsung Electronics 1-3

1-3 Static Electricity Precautions

5. Use only grounded-tip irons for soldering purposes.

These servicing instructions are for use by

1-4 Samsung Electronics

1-4 Installation Precautions

3. Do not place the product in areas with poor ventilation

4. Bend the external antenna cable when connecting it to

Samsung Electronics 1-5

1-6 Samsung Electronics

■ Core Parts Function

Samsung Electronics 2-1

2-2 Key Features

2-2 Samsung Electronics

INCH 21" FLAT 17" FLAT 15" FLAT

Samsung Electronics 2-3

2-3 Specifications Analysis

Model CS-21M20 CW-21M163NF

Product Type FLAT CRT FLAT CRT

2-4 Samsung Electronics

Warranty Card BN68-00514B

Video/Audio Cable - Internal shopping mall

Samsung Electronics 2-5

2-6 Samsung Electronics

3. Alignment & Adjustment

※When replacing the Module Service Instruction

2. When replacing the CRT Ass'y : No adjustments required

4. When replacing the Side AV Ass'y : No adjustments required

5. When replacing the Control Ass'y : No adjustments required

6. When replacing the PFC Ass'y : No adjustments required

Samsung Electronics 3-1

3-2 How to Access Service Mode

Info → Menu → Mute → Power On

※ When failing to enter Service Mode, repeat the procedure above.

2. The initial screen of Service Mode.

3. Functions of the Keys within Service Mode.

3-2 Samsung Electronics