Trinitron Kves29m90 PDF

SERVICE MANUAL AG3 CHASSIS
MODEL COMMANDER DEST. CHASSIS NO. MODEL COMMANDER DEST. CHASSIS NO.
KV-ES29M90 RM-916 Hong Kong SCC-P27A-A
1 2 3
4 5 6
7 8 9
0
TV
TRINITRON ® COLOR TV
Downloaded from www.Manualslib.com manuals search engine

KV-ES29M90
RM-916
SPECIFICATIONS
Note
Power requirements 110-240 V AC, 50/60 Hz

Power consumption (W) Indicated on the rear of the TV
Television system B/G, I, D/K, M
Color system PAL, PAL 60, SECAM, NTSC4.43, NTSC3.58
Stereo/Bilingual system NICAM Stereo Bilingual B/G, I; A2 Stereo Bilingual (German) B/G
Channel coverage
B/G VHF: E2 to E12 / UHF: E21 to E69 / CATV: S01 to S03, S1 to S41
I UHF: B21 to B68 / CATV: S01 to S03, S1 to S41
D/K VHF: C1 to C12, R1 to R12 / UHF: C13 to C57, R21 to R60
CATV: Z1 to Z39, S01 to S03, S1 to S41
M VHF: A2 to A13 / UHF: A14 to A79 /
CATV: A-8 to A-2, A to W+4, W+6 to W+84
˘ (Antenna) 75-ohm external terminal
Audio output (Speaker) 15W + 15W 10% distortion
Number of terminal
D (Video) Input: 4 Output: 1 Phono jacks; 1 VP-P, 75 ohms
≥ (Audio) Input: 4 Output: 1 Phono jacks; 500 mVrms
(S Video) Input: 2 Y : 1 Vp-p, 75 ohms,
unbalanced, sync
negative
C : 0.286 Vp-p, 75 ohms
(Component Video) Input: 1 Phono jacks
Y : 1 Vp-p, 75 ohms,
sync negative
CB : 0.7 Vp-p, 75 ohms
CR : 0.7 Vp-p, 75 ohms
Audio : 500 mVrms
DIGITAL IN Input: 1 Phono jack; 0.5 Vp-p, 75 ohms
2 (Headphones) Output: 1 Stereo minijack
Picture tube 29 inch
Tube size (cm) 72 Measured diagonally
Screen size (cm) 68 Measured diagonally
Dimension (w/h/d, mm) 722 × 561 × 524
Mass (kg) 56
Design and specifications are subject to change without notice.
CAUTION SAFETY-RELATED COMPONENT WARNING!!

SHORT CIRCUIT THE ANODE OF THE PICTURE TUBE AND COMPONENTS IDENTIFIED BY SHADING AND MARK ! ON
THE ANODE CAP TO THE METAL CHASSIS, CRT SHIELD, OR THE SCHEMATIC DIAGRAMS, EXPLODED VIEWS AND IN THE
CARBON PAINTED ON THE CRT, AFTER REMOVING THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE
ANODE. THESE COMPONENTS WITH SONY PARTS WHOSE PART
NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN
SUPPLEMENTS PUBLISHED BY SONY.
–2–
KV-ES29M90
RM-916
TABLE OF CONTENTS
Section Title Page Section Title Page
SELF DIAGNOSIS FUNCTION ................................ 4 6. DIAGRAMS

6-1. Block Diagram ......................................................... 63
1. GENERAL ........................................................................ 8 6-2. Frame Schematic Diagram ...................................... 81
6-3 Circuit Boards Location .......................................... 84
2. DISASSEMBLY 6-4. Schematic Diagrams and Printed Wiring Boards ... 84
2-1. Rear Cover Removal ............................................... 32 (1) Schematic Diagram of A Board .............................. 89
2-2. Speaker Box Removal ............................................. 32 (2) Schematic Diagram of D Board .............................. 93
2-3. H2 Board Removal .................................................. 32 (3) Schematic Diagram of D1 Board ........................... 101
2-4. Chassis Assy Removal ............................................. 33 (4) Schematic Diagrams of C, F1 and VM Boards ...... 109
2-5. Service Position ....................................................... 33 (5) Schematic Diagram of E Board .............................. 113
2-6. DH Board Removal ................................................. 33 (6) Schematic Diagrams of H1, H2 and H3 Boards .... 120
2-7. J Board Removal ...................................................... 33 (7) Schematic Diagram of B3 (1/6) Board .................. 125
2-8. B3, D1 and E Boards Removal ................................ 34 (8) Schematic Diagram of B3 (2/6) Board .................. 129
2-9. A and D Boards Removal ........................................ 34 (9) Schematic Diagram of B3 (3/6) Board .................. 133
2-10. H1 Board Removal .................................................. 34 (10) Schematic Diagram of B3 (4/6) Board .................. 137
2-11. F2 Board Removal ................................................... 34 (11) Schematic Diagram of B3 (5/6) Board .................. 141
2-12. Demagnetization Coil Removal .............................. 35 (12) Schematic Diagrams of B3 (6/6) and F2 Boards ... 145
2-13. Top Switch Removal ................................................ 35 (13) Schematic Diagram of DH Board .......................... 149
2-14. G2 Lead Removal .................................................... 35 (14) Schematic Diagram of A1 Board ........................... 155
2-15. Picture Tube Removal .............................................. 36 (15) Schematic Diagrams of BC4 and E1 Boards ......... 160
2-16. Frame Sub-Assy Disassembly ................................. 36 (16) Schematic Diagram of J Board ............................... 167
6-5. Semiconductors ....................................................... 172
3. SERVICE JIG
3-1. Jig Required for Servicing ....................................... 39 7. EXPLODED VIEWS
7-1. Speaker Bracket ...................................................... 181
4. SET-UP ADJUSTMENTS 7-2. Chassis .................................................................... 182
4-1. Beam Landing .......................................................... 40 7-3. Picture Tube ............................................................ 183
4-2. Convergence ............................................................. 41
4-3. Focus Adjustment .................................................... 43 8. ELECTRICAL PARTS LIST ...................................... 184
4-4. Neck Assy Twist Adjustment ................................... 43
4-5. G2 (Screen) and White Balance Adjustments ......... 44
5. CIRCUIT ADJUSTMENTS
5-1. Adjustments with Commander ................................ 45
5-2. Adjustment Method ................................................. 46
5-3. Picture Quality Adjustments .................................... 57
5-4. Deflection Adjustment ............................................. 59
5-5. A Board Adjustment After IC003 (Memory)
Replacement ............................................................. 60
5-6. Picture Distortion Adjustment ................................. 61
–3–
KV-ES29M90
RM-916
SELF DIAGNOSTIC FUNCTION
The units in this manual contain a self-diagnostic function. If an error occurs, the STANDBY/TIMER lamp will automatically
begin to flash.
The number of times the lamp flashes translates to a probable source of the problem. A definition of the STANDBY/TIMER
lamp flash indicators is listed in the instruction manual for the user’s knowledge and reference. If an error symptom cannot
be reproduced, the remote commander can be used to review the failure occurrence data stored in memory to reveal past
problems and how often these problems occur.
1. DIAGNOSTIC TEST INDICATORS

When an errors occurs, the STANDBY/TIMER lamp will flash a set number of times to indicate the possible cause of the
problem. If there is more than one error, the lamp will identify the first of the problem areas.
Result for all of the following diagnostic items are displayed on screen. No error has occured if the screen displays a “0”.
Diagnostic No. of times Self-diagnostic Probable Detected

Item STANDBY/TIMER display/Diagnostic Cause Symptoms
Description lamp flashes result Location
• Power does not Does not light — • Power cord is not plugged • Power does not come on.
turn on in. • No power is supplied to the
• Fuse is burned out F1601 TV.
(F1 Board) • AC power supply is faulty.
• +B overcurrent 2 times 002:000 or • H.OUT Q6807 is shorted. • Power does not come on.
(OCP) 002:001~255 • H.LIM Q6810 is shorted. • Load on power line is
shorted.
• +B overvoltage 3 times 003:000 or • PH 6602 faulty. • Power does not come on.
(OVP) 003:001~255 • 10.5V is not supplied.
(D board)
• Vertical deflection 4 times 004:000 or • V.OUT IC6800 faulty • Vertical deflection pulse is
failure 004:001~255 D6816 faulty stopped.
D6817 faulty • Vertical size is too small.
D6824 faulty • Vertical deflection stopped.
R6852 open
R6851 open
• White balance 5 times 005:000 or • G2 is improperly adjusted. • No raster is generated.
failure (no 005:001~255 (Note 2) • CRT cathode current
PICTURE) • CRT problem. detection reference pulse
• Video OUT IC9001, 9002, output is small.
9003 are faulty. (C board)
• IC8306 (J board) and
IC4301 (E board) are faulty.
• No connection E board to C
board.
• Horizontal 6 times 006:000 or • C6831 is open circuit. • H pulse output is too high.
deflection 006:001~225 • CN6101 (D1 board) is
failure disconnected.
• Audio Protection 7 times 007:000 or • Power supply fails. • There is picture but speaker
007:001~225 • IC1203, IC1204 faulty does not release sound.
• Micro reset — 101:00 or • Discharge CRT (C Board) • Power is shut down shortly,
101:001~225 • Static discharge after this return back to
• External noise normal.
• Detect Micro latch up.
Note 1: Refer to screen (G2) Adjustment in section 4-5 of this manual.
–4–
KV-ES29M90
RM-916
2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT
2 times
3 times
Lamp ON 0.3 sec.

Lamp OFF 0.3 sec. Lamp OFF 3 sec.
4 times
5 times
6 times
7 times
STANDBY/SLEEP lamp
Diagnostic Item Flash Count*

+B overcurrent 2 times
+B overvoltage 3 times
V deflection stop 4 times
White balance failure 5 times
High voltage protector 6 times
Audio Protection 7 times
* One flash count is not used for self-diagnostic.
3. STOPPING THE STANDBY/TIMER FLASH

Turn off the power switch on the TV main unit or unplug the power cord from the outlet to stop the STANDBY/TIMER lamp
from flashing.
–5–
KV-ES29M90
RM-916
4. SELF-DIAGNOSTIC SCREEN DISPLAY

For errors with symptoms such as “power sometimes shuts off” or “screen sometimes goes out” that cannot be confirmed, it
is possible to bring up past occurances of failure for confirmation on the screen:
[To Bring Up Screen Test]

In standby mode, press buttons on the remote commander sequentially in rapid succession as shown below:
[Screen display] / channel [5] / Sound volume [-] / Power ON

˘
Note that this differs from entering the service mode (mode volume [+]).
Self-Diagnosis screen display
SELF DIAGNOSTIC
002 : 000 Numeral "0" means that no fault has been detected.
003 : 000
004 : 000
005 : 001 Numeral "1" means a fault has been detected.
006 : 002 Numeral "2" means two faults have been detected.
007 : 000
101 : 000
5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY

Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen
during repairs. When you have completed the repairs, clear the result display to “0”.
Unless the result display is cleared to “0”, the self-diagnostic function will not be able to detect subsequent faults after
completion of the repairs.
[Clearing the result display]

To clear the result display to “0”, press buttons on the remote commander sequentially as shown below when the diagnostic
screen is being displayed.
Channel [8] / 0
[Quitting Self-diagnostic screen]

To quit the entire self-diagnostic screen, turn off the power switch on the remote commander or the main unit.
–6–
KV-ES29M90
RM-916
6. SELF-DIAGNOSTIC CIRCUIT
IC4301 IC001 IC003

RGB JUNGLE OVP OCP SYSTEM MEMORY
FROM 3 SDA
CRT (IK) 25 IKIN 5
6
[H] IC6801 20 XRAY
LED 54
[V] D6806/D6801 16 V PROT SDA
5
CXA2100Q
IC004
MEMORY
[+B overcurrent ªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q6610

and Q6609.
If Q6610 and Q6609 go to ON, the voltage to the pin3 of IC001 go to UP.
The unit will automatically turn off.
[+B overvoltage ªOVPº] Occurs when an overvoltage on the +B(135) line is detected by D6635,

Q6611 and Q6612. If Q6611 and Q6612 go to ON, the voltage to pin6 of
IC001 go to UP. The unit will automatically turn off.
[Vertical deflection failure] Occurs when an absence of the vertical deflection pulse is detected by

Q6811, Q6819, Q6820, Q6821 and D6801. Shut down the power supply.
[White balance failure] If the RGB levels do not balance or become low level within 5 seconds.
This error will be detected by IC4301.
TV will stay on, but there will be no picture.
[High voltage protector of Horizontal Deflection] Occurs when an overvoltage of horizontal pulse is detected by D6809 and

IC6801.
If the voltage of 7 pin of IC6801 goes to High, the voltage to pin20 of
IC4301 go to UP. The unit will automatically turn off.
–7–
KV-ES29M90
RM-916
The operating instructions mentioned here are partial abstracts SECTION 1
from the Operating Instruction Manual. The page numbers of
the Operating Instruction Manual remain as in the manual. GENERAL
Using Your New TV

WARNING
• Dangerously high voltages are present inside the TV.
• Operate the TV only between 110 – 240 V AC. Getting Started
Step 1
Connect the antenna
If you wish to connect a VCR, see the “Connecting a VCR” diagram below.
For your own safety, do not touch any part of the Rear of TV
TV, the power cord and the antenna cable during Install the TV in a stable position. Do not allow
lightning storms. children to climb onto it.
or
Antenna cable (not supplied)
IEC connector
(not supplied)
–8–
Do not operate the TV if any liquid or solid object

To prevent fire or shock hazard, do not expose falls into it. Have it checked immediately by : Signal flow
Antenna cable (not supplied)
the TV to rain or moisture. qualified personnel only.
CAUTION
Do not connect the power cord until all other connections are complete;
otherwise, a minimal current leakage through the antenna and/or other
terminals to the ground could occur.
Connecting a VCR
To play a video tape, press t (see page 11).
To ˘ (antenna)
Do not install the TV in a confined space, such Clean the TV with a dry and soft cloth.
as a bookcase or built-in cabinet. Do not use benzine, thinner, or any other chemicals
Antenna cable (not supplied) Rear of TV
Do not block the ventilation openings of the TV. to clean the TV. Do not scratch the picture tube.
Pull the power cord out by the plug. Do not pull To antenna To
the power cord itself. Disconnect the TV if you Do not plug in too many appliances to the same output VCR (S video input)
are not going to use it for several days. power socket. Do not damage the power cord.
Y
S video cable
(not supplied) CB
AUDIO VIDEO CR
R L
L DIGITAL IN
(MONO)
L (DOLBY DIGITAL/PCM)
VIDEO IN
VIDEO OUT To S video R R

1 2
output 3
To video and
Do not open the cabinet and the rear cover of the Do not install the TV in hot, humid or excessively audio outputs To t 1, 2 or 3 (video input)
TV. Refer servicing to qualified personnel. dusty places. (yellow)
Audio/Video cable -L (MONO) (white)
2 4 Using Your New TV (not supplied) -R (red)
: Signal flow

Notes Connecting optional components
• If you connect a monaural VCR, connect the yellow plug to (the yellow
jack) and the black plug to -L (MONO) (the white jack). You can connect optional audio/video components, such as a VCR, multi disc player,
• If you connect a VCR to the 8 (antenna) terminal, preset the signal camcorder, video game, or stereo system. To watch and operate the connected
output from the VCR to the program number 0 on the TV. equipment, see pages 11 and 25.
• When both the (S video input) and t 1 (video input) are connected,
Using Your New TV
the (S video input) is automatically selected. To view the video input Connecting a camcorder/video game equipment
to t 1 (video input), disconnect the S video cable.
using the t (video input) jacks
Step 2 Video game equipment Side panel
To 2
Insert the batteries into To S video output (S video input)
the remote b or S video cable
Camcorder (not supplied)
Notes
…4
• Do not use old batteries or different types of batteries together. L
• To operate some of the functions of your TV, you may have to open the Audio/Video cable ≥ (MONO)
remote control cover. (not supplied) R

To video and
audio outputs To … 4 AUTO
PROGR
(video input)
b Notes
: Signal flow
• When connecting video game equipment, display the “FEATURE” menu

and select “ON” for “GAME MODE” to adjust the picture setting that is
suitable for video games (see page 36).
Step 3 • You can also connect video equipment to the t 1, 2, or 3 (video input)
–9–
jacks at the rear of your TV.

Preset the channels automatically • When both the (S video input) and t 4 (video input) are connected,
Side panel the (S video input) is automatically selected. To view the video input
to t 4 (video input), disconnect the S video cable.
2 g
U
1 U
Connecting audio/video equipment using the T

(monitor output) jacks Antenna cable (not supplied)
…4
L
Rear of TV
≥
R
(MONO)
2 AUTO
AU TO PROGRAM
PR : 0 1
T V S Y S : AU TO
1
Y
To
AUTO
PROGR
PROGR
VH F L OW antenna Audio system
CB output VCR
CR
or
Notes To
L L DIGITAL IN
(DOLBY DIGITAL/PCM) To video and
• To stop the automatic channel presetting, press MENU twice. (MONO)
audio inputs audio

• If your TV has preset an unwanted channel or cannot preset a particular R R inputs
1 2 3
channel, then preset your TV manually (see page 41).
• To open the side panel of your TV, push on it until you hear a click, then it (yellow)
will open. To T Audio cable
-L (MONO) (monitor (not supplied)
(white) output)
2
-R (red)
Audio/Video cable (not supplied)
PUSH b PUSH
…4 Note
: Signal flow
L
(MONO)
• If you select “DVD” on your TV screen, no signal will be output at the

≥
R
AUTO
T (monitor output) jacks (see page 11).

PROGR
Using Your New TV 5 6 Using Your New TV
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Connecting optional components (continued)
Connecting a DVD player to (component video input)
1 Using an audio cable, connect R and L under (component video input) on your Connecting a DVD player to t (video input)
TV to the LINE OUT, AUDIO R and L output connectors on your DVD player.
2 Using a coaxial digital connecting cord, connect DIGITAL IN under (component Connect t 1, 2, or 3 (video input) / (audio/video) connectors on your TV to
video input) on your TV to the DIGITAL OUT, COAXIAL output connector on your LINE OUT on your DVD player.
Using Your New TV
DVD player. To t 1, 2, or 3
To audio/video
3 Using a component video cable, connect Y, CB, and CR under (component video output (video input)
input) on your TV to the COMPONENT VIDEO OUT Y, CB, and CR output
Audio/Video cable
connectors on your DVD player. (not supplied)
4 Press t on the remote or the TV until “DVD” appears on the screen.
Component video cable To

(not supplied) (component video input) R-AUDIO-L VIDEO L
(MONO)
To component LINE OUT
video output (yellow) R

1 2 3
-L (MONO) (white)
Audio cable (not supplied)
To audio -R (red) : Signal flow
output Y
To coaxial
– 10 –
digital CB
output Notes
CR
• Since the high quality pictures on a DVD disc contain a lot of information,
L DIGITAL IN
(DOLBY DIGITAL/PCM) picture noise may appear. In this case, adjust the sharpness (“SHARP”)
CR CB Y R-AUDIO-L VIDEO OPTICAL COAXIAL
under “PERSONAL ADJUST” in the “PICTURE MODE” menu (see
R
COMPONENT VIDEO OUT S VIDEO OUT LINE OUT DIGITAL OUT
To L (white) page 31).
Coaxial digital R (red) • Connect your DVD player directly to your TV. Connecting the DVD
DVD
connecting player through other video equipment will cause unwanted picture noise.
player : Signal flow
cord (not To DIGITAL IN
supplied) (digital input)
Notes
• Some DVD player terminals may be labeled differently:
Connect To (on the DVD player)

Y (green) Y
CB (blue) Cb, B-Y or PB
CR (red) Cr, R-Y or PR
• When connecting to (component video input) on your TV, you must

connect Y, CB, and CR to receive the video signals, and at least connect
DIGITAL IN to receive digital audio signals or connect L and R to receive
analog audio signals (see page 32).
• When making connections to DIGITAL IN under (component video
input) on your TV, always set “DIGITAL IN: OFF” in the “A/V
CONTROL” menu. After completing all connections, then set “DIGITAL
IN: ON”. If you set “DIGITAL IN: ON” while still making connections to
DIGITAL IN (component video input), a loud noise may suddenly
come out from the speakers, affecting your hearing and causing damage
to the speakers (see page 32).
continued

Securing the TV Watching the TV
DRC-MF
To prevent the TV from falling, secure the TV using one of the following methods: This section explains various functions A/B
and operations used while watching the

Using Your New TV TV. Most operations can be done using
the remote.
A the
With the supplied screws, attach the stabilizer band to the TV stand and to
rear of the TV using the provided hole.
1 2 3
Number buttons
MENU ENTER … – . + – PROGR + 4 5 6
7 8 9
OR 0
JUMP
B TV
Pass a cord or chain through the clamps and secure them to the rear of the
and a wall or pillar.
PIC
MODE
SOUND
MODE SURROUND
PROGR
FAVORITE INDEX
. MENU PROGR
PROGR +/–
ENTER
20 mm
PRESET VTR 1 2 3 DVD
U
3.8 mm
A B
– 11 –
1 Press ! to turn on the TV.

U
When the TV is in standby
mode (the 1 indicator on
the TV is lit red), press 1/1
OR on the remote or on the TV.
2 Press PROGR +/– or the

number buttons to select 1 2 3
the TV channel. PROGR
or 4 5 6
For double digit numbers,
press ÷, then the number 7 8 9
Note (e.g., for 25, press ÷, then 0
JUMP
• Use only the supplied screws. Use of other screws may damage the TV. 2 and 5).
To select a TV program quickly

(1) Press and hold PROGR +/–.
(2) Release PROGR +/– when the desired program number appears.
Note
• When you select a TV program quickly, the picture may be disrupted.
This does not indicate a malfunction.
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Watching the TV (continued)
MENU ENTER … – . + – PROGR +
DRC-MF Using the Remote Control Button Joystick ( )

You can select the menu item on the
A/B 7 8 9
screen by moving up, down, left or To move
Using Your New TV
JUMP
right (see page 29). 0
1 2 3 To confirm a selected item, press . PIC

MODE
SOUND
MODE SURROUND
You can also press ENTER on the remote PROGR
4 5 6 to confirm a selected item.

FAVORITE INDEX
7 8 9 .
. MENU PROGR
JUMP
0 JUMP To confirm
U PIC SOUND
MODE MODE SURROUND
ENTER
PROGR
FAVORITE INDEX
MENU
. MENU PROGR
Changing the menu language

You can change the menu language as well as the on-screen language. For details on
– 12 –
ENTER how to use the menu, see “Introducing the menu system” on page 27.
DRC-MF
ENTER
. +/–
VIDEO
1 Press MENU. A / V CONTROL

DRC-MF: DRC1250
PICTURE MODE: DYNAMIC
b
TITLE
MENU SOUND MODE: DYNAMIC

SURROUND: OFF
DIGITAL IN : OFF
TV
2 Move
select
up or down to
, then press .
S E T UP
LANGUAGE : ENG L I SH
Additional tasks
b b CH I L D L OCK : PR 0 1 OF F
P I C ROT A T I ON
F A VOR I T E CH
To Press I N T E L L I GEN T VO L : O F F
Turn off temporarily 1/1.
The 1 indicator on the TV lights up red.
3 Make sure “LANGUAGE”
is selected then press .
S E T UP
LANGUAGE/: ENG L I SH
Turn off completely ! on the TV.
b CH I L D L OCK
P I C ROT A T I
Adjust the volume 2+/–. F A VOR I T E C
I N T E L L I GEN
Mute the sound %.
Watch the video input
(VCR, camcorder, etc.)
t (or t on the TV) to select “VIDEO 1”,
“VIDEO 2”, “VIDEO 3”, “VIDEO 4”or “DVD”.
4 Move up or down to
select the desired
/ LANGUAGE
To return to the TV screen, press a (or t on the TV). language (e.g., ),
Jump back to the previous channel JUMP. then press . b b
Display the on-screen information* . The selected menu
language appears.
* Some picture/sound settings, and either the program number or video
mode are displayed. The on-screen display for the picture/sound settings
disappears after about 3 seconds. To return to the normal screen
continued Press MENU.

Advanced Operations
Setting the Wake Up timer Selecting the picture PIC

MODE
SOUND
MODE SURROUND
and sound modes PROGR
1 Press until the desired SOUND MODE

FAVORITE INDEX
period of time appears. WAKE UP TIMER:10M PIC MODE

After 10 minutes . MENU PROGR
The Wake Up timer starts Using Your New TV You can select picture and sound modes
immediately after you and adjust the setting to your preference
have set it. WAKE UP TIMER:OFF WAKE UP TIMER:12H00M
in the “PERSONAL” option. ENTER
No Wake Up Timer After 12 hours

Selecting the picture mode

2 Select the TV channel or video mode you want to wake up to.
Press PIC MODE

3 Press 1, or set the Sleep timer if you want the TV to turn off automatically.
The indicator on the TV lights up orange.
repeatedly until the
PIC
MODE
DYNAMIC STANDARD
desired picture mode is

selected.
To cancel the Wake Up timer PERSONAL HI-FINE
Press until “WAKE UP TIMER: OFF” appears, or turn off the

Select To
TV’s main power.
Note “DYNAMIC” receive high contrast pictures.
• If no buttons or controls are pressed for more than two hours after the TV “STANDARD” receive normal pictures.
is turned on using the Wake Up timer, the TV automatically goes into
standby mode. To resume watching the TV, press any button or control on “HI-FINE” receive higher resolution pictures with mild contrast.
the TV or the remote. “PERSONAL” receive the last adjusted picture setting from the “ADJUST” option in the
– 13 –
“A/V CONTROL” menu (see page 31).
Setting the Sleep timer

Selecting the sound mode
Press until the desired
period of time appears. SLEEP TIMER:30M SLEEP TIMER:60M Press SOUND MODE
After 30 minutes After 60 minutes repeatedly until the SOUND ≥ DYNAMIC ≥ DRAMA
The Sleep timer starts MODE
immediately after you desired sound mode is
have set it. selected.
SLEEP TIMER:OFF SLEEP TIMER:90M ≥ PERSONAL ≥ SOFT
No Sleep Timer After 90 minutes
Select To
To cancel the Sleep timer “DYNAMIC” listen to dynamic and clear sound that emphasizes both the low and high
tones.
Press until “SLEEP TIMER: OFF” appears, or turn the TV off.
“DRAMA” listen to sound that emphasizes voice and high tones.
“SOFT” receive soft sound.
“PERSONAL” receive the last adjusted sound setting from the “ADJUST” option in the
“A/V CONTROL” menu (see page 31).
Tip
• You can also set the picture and sound modes using the menu (see
“Changing the “A/V CONTROL” setting” on page 30).
Using Your New TV 13 14 Advanced Operations
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Viewing higher Viewing your 7 8 9
quality pictures favorite channels
DRC-MF
JUMP
0
DRC-MF
— “DRC-MF” A/B
— “FAVORITE CH” PIC
MODE
SOUND
MODE SURROUND
PROGR
FAVORITE INDEX
The Digital Reality Creation-Multi 1 2 3 You can display seven favorite channels FAVORITE
Function (DRC-MF) feature allows you for quick and easy selection. . MENU PROGR
4 5 6
to enjoy higher quality pictures on your The last seven channels selected with
TV. You can select “DRC1250” to watch 7 8 9
JUMP the number buttons are displayed in
super real (higher resolution) pictures, 0 “AUTO” mode. You can set up your
ENTER
ENTER
or “DRC100” to reduce flicker if PIC SOUND own favorite channels in “MANUAL” PRESET VTR 1 2 3 DVD
necessary. MODE MODE SURROUND
mode under the “FAVORITE CH” menu

PROGR
FAVORITE INDEX
(see “Changing the favorite channel
.
setting” on page 39).
MENU PROGR
TV
Advanced Operations
ENTER
– 14 –
Selecting a favorite channel
Press DRC-MF repeatedly DRC-MF

1 Press FAVORITE.
FAVORITE
FAVORITE CH 1
until you receive the DRC-MF: DRC1250 DRC-MF: DRC100

The last seven channels 3
desired picture quality. selected with the number

buttons appear.
b 4
12 10 8 6
Select To
“DRC1250” select higher resolution pictures. 2 Move up, down, left or
right to select the desired
FAVORITE CH 1
“DRC100” reduce flicker on the screen. 3

channel (e.g. PR 8), then
press . b b 4
12 10 8 6
Tip
• When the broadcast signal is weak, you may see some dots or noise on the
TV screen. To reduce this interference, display the “A/V CONTROL”
menu and select “ADJUST” in “PICTURE MODE”, then adjust “SHARP”
to reduce the sharpness (see page 31).
3 Press again.
FAVORITE CH
1.PR 01
8
2.PR 03
Note
• The DRC-MF mode is not selectable when using the “PROGRAM INDEX”
b 3.PR 04
or “FAVORITE” channel feature, or when the “GAME MODE”, Picture-In- 7.PR 12 6.PR 10 5.PR 08 4.PR 06
Picture (“PIP”), or “TWIN” mode is turned “ON”.
Note
• When you use your TV for the first time, seven preset channels appear.
Advanced Operations 15 16 Advanced Operations

Watching two programs at the same time (continued)
Watching two
programs at the Additional PIP/TWIN pictures tasks
same time To Press/Move
— “PIP”, “TWIN”
DRC-MF
change a TV program in the PIP Press PROGR + or PROGR –. For a video input,
screen or in the right TWIN picture press .
VIDEO
swap pictures between the main Press .

With the Picture-in-Picture (PIP) or TITLE
and PIP screens
TWIN pictures features, you can display
a different TV program or video within
or beside the main picture. PROGR +
PROGR –
/ freeze the PIP screen Press .
PROGR +/PROGR – To unfreeze the screen, press the button again.
PIC SOUND change the position of the PIP screen Press D.
MODE MODE SURROUND
PROGR
FAVORITE INDEX
. MENU PROGR
swap the right and left pictures of Press .
the TWIN pictures
ENTER
Displaying the PIP screen

change the screen size of the TWIN Move left to increase the left screen size.
Press . pictures
– 15 –
Move right to increase the right screen size.

12
Displaying TWIN pictures

Press .
10 12
Notes
• The button does not function in the TWIN pictures mode.
• When you display a video input on the PIP screen at a faster/slower
To return to the normal screen speed, the picture may be disrupted depending on the VCR type.
Press (when in the PIP screen) or (when in the TWIN picture • If you display different color systems on the main screen and the PIP
screen). screen, the size of the PIP screen may be different and the PIP picture may
be disrupted. This does not indicate a malfunction of the TV.
Tip • In the TWIN picture screen, you can only operate and hear the sound of
• You can also display the PIP screen or TWIN pictures using the menu (see the main left screen ( appears on the screen).
“Changing the MULTI PICTURE setting” on page 33). • When the button is pressed, the TV screen flickers or goes blank for
continued about one second before the TWIN pictures appear. This does not indicate
a malfunction of the TV.
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Displaying Displaying multiple programs (continued)
1 2 3
multiple 4 5 6 To view the next or the previous twelve preset programs
programs 7 8 9
JUMP
This works only when the number of the preset TV programs is
more than twelve.
— “PROGRAM INDEX” 0
Press PROGR +/– on the remote or the TV.
PIC SOUND
MODE MODE SURROUND
1 2 3 4 13 14 15 16
The PROGRAM INDEX feature displays FAVORITE
PROGR
INDEX
all of the preset TV programs on twelve PROGR INDEX 12

16 5
16 17
or seven sub screens for direct selection. . MENU PROGR 11 6 18
PROGR +/– 10 9 8 7
ENTER
To select the desired program directly from the sub screens

1 Move up, down, left or right to move the frame to the screen
of the program you want to watch.
1 2 3 4
– 16 –
TV 12
16 5
b 11 6
10 9 8 7
Press PROGR INDEX.

Still sub screens
PROGR
The first twelve preset
programs appear one by
INDEX
b 1 2 3 4
2 Press .
1 2 3 4
one, clockwise from the Main screen

12
16 5
upper left corner.

12
8 5
11
10 9 8
6
7
b 11 6
10 9 8 7
When the number of the 1

preset TV programs is less 16 Still 3 Press again.
than eight, the first seven 2 sub
Main screen
preset programs appear 3
screens 8
one by one, clockwise from
the upper right corner.
7 6 5 4
b
Tip
• Pressing the number buttons directly displays the program.
Tip
• When you press the PROGR INDEX button in the TWIN pictures mode,
the left picture appears as the main screen of the PROGRAM INDEX
mode.
continued

To return to the normal screen Listening with
surround sound
DRC-MF
Press PROGR INDEX again, or:

1 Select “PROGRAM INDEX” from the “MULTI PICTURE” menu. A/B
2 Press . The surround feature enables you to

enjoy the sound effects of a concert hall
Tip 1 2 3
or movie theater.
• You can also display multiple programs using the menu (see “Changing 4 5 6
the MULTI PICTURE setting” on page 33).
7 8 9
JUMP
0
Note
• When displaying multiple programs, only the sound of the main screen is PIC
MODE
SOUND
MODE SURROUND
heard. SURROUND
PROGR
FAVORITE INDEX
Press SURROUND
SURROUND SURROUND: VIRTUAL SURROUND: TruSurround
repeatedly until you
receive the desired
surround sound.
SURROUND: OFF SURROUND: SIMULATED
Select To
“a VIRTUAL” listen to Dolby* Surround encoded sound.
– 17 –
“TruSurround” listen to the surround sound that spreads out to the rear of a room.
“SIMULATED” listen to monaural sound with a stereo-like effect.
“OFF” turn off the surround sound.
Notes
• The Virtual Dolby Surround of this model consists of Dolby Digital, Dolby
Pro Logic and TruSurround.
• The “a VIRTUAL” (Virtual Dolby Digital) is only available when receiving
a Dolby Digital signal through the DIGITAL IN (component video
input) jack at the rear of your TV and “DIGITAL IN: ON” in the “A/V
CONTROL” menu is selected (see pages 7 and 30).
• When using the DIGITAL IN (component video input) jack at the rear
of your TV, the available surround modes depend on the type of digital
signal being received.
• SIMULATED uses SRS (MONO).
* Manufactured under license from Dolby Laboratories Licensing Corporation.
DOLBY, the double-D symbol a and “PRO LOGIC” are trademarks of
Dolby Laboratories Licensing Corporation.
“ ” is a trademark of SRS Labs, Inc. SRS and the SRS
TM
symbol are registered trademarks of SRS Labs, Inc. in the United

States and selected foreign countries. SRS and TruSurround are
incorporated under license from SRS Labs, Inc. and are protected
under United States Patent Nos.4,748,669 and 4,841,572 with
numerous additional issued and pending foreign patents”.
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Enjoying stereo or Enjoying stereo or bilingual programs (continued)
bilingual DRC-MF
When receiving an A2 (German) program

A/B
programs A/B
Broadcasting On-screen display (Selected sound)
A2 (German) stereo STEREO
MONO
1 2 3 (Regular sound) (Stereo sound)
You can enjoy stereo sound or bilingual 4 5 6
programs of NICAM and A2 (German)
7 8 9
stereo systems. JUMP A2 (German) bilingual
0 MAIN SUB
(Main sound) (Sub sound)
PIC SOUND
MODE MODE SURROUND
PROGR
FAVORITE INDEX
Receiving area for NICAM and A2 (German) programs

Press A/B repeatedly until
you receive the sound you System Receiving area
– 18 –
want. STEREO
A/B NICAM Hong Kong, Singapore, New Zealand, Malaysia,
The on-screen display Thailand, etc.
changes to show the
A2 (German) Australia, Malaysia, Thailand, etc.
selected sound and the
Â indicator on the TV Notes
lights up red. • If the signal is very weak, the sound becomes monaural automatically.
• If the stereo sound is noisy when receiving a NICAM program, select
“MONO”. The sound becomes monaural, but the noise is reduced.
When receiving a NICAM program • Before receiving a NICAM stereo program in China, please check the
NICAM broadcast condition at your area. When receiving a NICAM
stereo program, the receiving conditions might vary depending on area. In
addition, different strength of the NICAM broadcast signal might affect
Broadcasting On-screen display (Selected sound) the receiving quality.
NICAM stereo NICAM MONO
(Stereo sound) (Regular sound) If the sound is distorted or noisy when receiving a monaural
program through the 8 (antenna) terminal
Press A/B repeatedly until “MONO” appears on the screen.
NICAM bilingual
NICAM NICAM MONO To cancel the monaural sound setting, press A/B again until
MAIN SUB (Regular sound) “AUTO” appears on the screen.
(Main sound) (Sub sound)
MONO AUTO
NICAM monaural NICAM MONO
MAIN (Regular sound)
(Main sound)
Notes
• The “MONO” or “AUTO” setting is memorized for each program
position.
• You cannot receive a stereo broadcast signal when the TV is in the
continued “MONO” setting. Normally, set the TV to “AUTO”.

Operating optional components (continued)
Operating
optional Operating a VCR using the remote
components DRC-MF
To
turn on/off
Press
VIDEO I /1
VIDEO
record ( while pressing r.
You can use the supplied remote to TITLE
VIDEO I/1 play (
operate Sony video equipment such as Video equipment stop p
operation buttons
Beta, 8 mm, VHS or DVD. fast forward ()) +
rewind the tape (0) =
PROGR +
pause P
PROGR –
Press again to resume normal playback.
search the picture forward ()) + or =during playback.
PIC
MODE
SOUND
MODE SURROUND or backward (0) Release to resume normal playback.
PROGR
FAVORITE INDEX
MENU
Operating a DVD player using the remote
. MENU PROGR
To Press
turn on/off VIDEO I /1
ENTER
play (
PRESET VTR 1 2 3 DVD stop p
VTR
pause P
Press again to resume normal playback.
step through different tracks of an + to step forward or = to step backward.
– 19 –
audio disc
display the title menu TITLE
Setting up the remote to work with other display the menu MENU while holding down r.
connected equipment select the menu item Move up, down, left or right while holding
down r.
Switch VTR to select the For example, to operate a
desired equipment type Sony 8 mm VCR:
(see the chart below). VTR 1 2 3 DVD
To control Select
DVD DVD
VTR1 (Beta) 1
VTR2 (8 mm) 2
VTR3 (VHS) 3
Notes
• If your video equipment is furnished with a COMMAND MODE selector,
set this selector to the same position as the VTR switch.
• If the equipment does not have a certain function, the corresponding
button on the remote will not operate.
continued
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Adjusting Your Setup (MENU)
Introducing the menu system Introducing the menu system (continued)
The MENU button lets you open a menu and change the settings of your TV. The Level 1 Level 2 Level 3/Function
following is an overview of the menu system. “SET UP” “LANGUAGE” Change the menu language:
Return icon “ENGLISH” t “ ” (Chinese) t “ ” (Arabic)
A/V CONTROL icon Name of the current “CHILD LOCK” Lock out specific channels.
S E T UP menu
MULTI PICTURE icon “PIC ROTATION” Rotate the picture.
LANGUAGE/: ENG L I SH Guide mark icon
FEATURE icon CH I L D L OCK “FAVORITE CH” Set favorite channels.
SET UP icon P I C ROT A T I Menu level 3
F A VOR I T E C “INTELLIGENT Adjust the volume automatically.
CH PRESET icon I N T E L L I GEN VOL”
Menu level 2 “CH PRESET” “AUTO Preset channels automatically.
Menu level 1 PROGRAM”
“MANUAL Preset channels manually.
PROGRAM”
Level 1 Level 2 Level 3/Function
“SKIP” Skip unwanted or unused program numbers.
“A/V “DRC-MF” Select the “DRC-MF” mode:
CONTROL” “DRC1250” t “DRC100” “TV SYS” Select the TV system:
“B/G” t “I” t “D/K” t “ M”
“PICTURE MODE” Select the picture mode:
– 20 –
“DYNAMIC” t “STANDARD” t “HI-FINE” t “COL SYS” Select the color system:

“PERSONAL” t “ADJUST” “AUTO” t“ PAL” t “SECAM” t “NTSC3.58” t
“NTSC4.43”
“ADJUST” Adjust the “PERSONAL” option:
“PICTURE” t “COLOR” t “BRIGHT” t “HUE” t * The BBE is manufactured by Sony Corporation under license from BBE
“SHARP” Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No. 4,482,866.
“SOUND MODE” Select the sound mode: The word “BBE” and the BBE symbol are the trademarks of BBE Sound, Inc.
“DYNAMIC” t “DRAMA” t “SOFT” t
Adjusting Your Setup (MENU)
“PERSONAL” t “ADJUST”
“ADJUST” Adjust the “PERSONAL” option:
“BASS” t “TREBLE” t “BALANCE” t “BBE”*
“SURROUND” Select the “SURROUND” mode:
“a VIRTUAL” t “TruSurround” t “SIMULATED” t
“OFF”
“DIGITAL IN” Activate or deactivate the digital audio input jack at the
rear of your TV.
“MULTI “PIP” Activate or deactivate the PIP feature.
PICTURE” “PIP POSITION” Change the position of the sub screen.
“SWAP” Swap the pictures between the main and sub screens.
“TWIN” Display a TV program or video beside the main screen.
“PROGRAM INDEX” Display all the preset TV programs at the same time.
“FEATURE” “WIDE MODE” Activate or deactivate WIDE MODE feature.
“ECO MODE” Activate or deactivate ECO MODE feature.
“GAME MODE” Activate or deactivate GAME MODE feature.
continued
Adjusting Your Setup (MENU) 27 28 Adjusting Your Setup (MENU)

How to use the menu Changing the “A/V
MENU
CONTROL” setting
MENU PROGR
PIC SOUND
MODE MODE SURROUND
Press MENU to display A / V CONTROL
the menu.
b
PROGR DRC-MF: DRC1250 ENTER
FAVORITE INDEX
PICTURE MODE: DYNAMIC The “A/V CONTROL” menu allows you ENTER
SOUND MODE: DYNAMIC
MENU SURROUND: OFF to adjust the picture and sound settings.
. MENU PROGR DIGITAL IN : OFF

DRC-MF: DRC1250
Move the button
b PICTURE MODE: DYNAMIC
ENTER
MENU SOUND MODE: DYNAMIC

PRESET VTR 1 2 3 DVD joystick ( ) up, MU L T I P I C T URE
P I P: OF F SURROUND: OFF
down, left or right
to select the desired
b PIP POSITION :
SWA P
TW I N : OFF
DIGITAL IN : OFF
PROGRAM I NDE X
item. 2 Move
select
up or down to
, then press .
A / V CONTROL
DRC-MF: DRC1250
TV Press the button b b PICTURE MODE: DYNAMIC

SOUND MODE: DYNAMIC
joystick ( ) to SURROUND: OFF
DIGITAL IN : OFF
confirm the selection
MU L T I P I C T URE
and/or go to the next or
level. You can also ENTER b P I P: OF F
P I P POS I T I ON :
SWA P
select either “DRC-MF”,
A / V CONTROL
DRC-MF : DRC1250
b b
TW I N : OFF
press ENTER on the PROGRAM I NDE X “PICTURE MODE”, “SOUND PICTURE MODE DRC100
remote to do this. SOUND MODE
MODE”, “SURROUND”, or SURROUND : O
“DIGITAL IN“, then press . DIGITAL IN
– 21 –
Other menu operations

select the desired option,
To Press/Move
then press . b
Adjust the setting value Move up, down, left or right.
Move left or right. For Select
Move to the next/previous menu level
Cancel the menu Press MENU. “DRC-MF“ either “DRC1250“ or “DRC100“.
“PICTURE MODE“ either “DYNAMIC“, “STANDARD“, “HI-FINE“, “PERSONAL“*, or “ADJUST“.
Tips
“SOUND MODE“ either “DYNAMIC“, “DRAMA“, “SOFT“, “PERSONAL“*, or “ADJUST“.
• If you want to exit from Menu level 2 to Menu level 1, move up or
down until the return icon (3) is highlighted, then press or ENTER. “SURROUND“ either “a VIRTUAL“, “TruSurround“, “SIMULATED“, or “ OFF“.
• The MENU, ENTER, and 2 +/– buttons on the TV can also be used for
the operations above. “DIGITAL IN“ either “ON“ or “OFF“.
Note * When the “PERSONAL” mode is selected, the last adjusted picture/sound
• If more than 60 seconds elapse between entries, the menu screen settings from the “ADJUST” option are received (see page 31).
automatically disappears.
Tip
• For details on the options under the “DRC-MF“, “PICTURE MODE“/
“SOUND MODE“, “SURROUND“ and “DIGITAL IN“ modes, see pages
15, 14, 22 and 32 respectively.
To return to the normal screen

Press MENU.
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Changing the “A/V CONTROL” setting (continued)
Adjusting the “ADJUST” options under “PICTURE MODE”
select the desired item
Setting the “DIGITAL IN” options
(e.g., “COLOR”), then b b 1 In the “DIGITAL IN” A / V CONTROL
press . COLOR 80 menu, move up or DRC-MF : DRC ON
down to select the b PICTURE MODE OFF
SOUND MODE
2 Adjust the value according to the following table, then press . desired option (see table
below).
SURROUND : O
DIGITAL IN
For Move down or left to Move up or right to
“PICTURE” decrease picture contrast increase picture contrast Select To
“COLOR” decrease color intensity increase color intensity “ON“ receive digital audio signal through DIGITAL IN (component
video input) jack.
“BRIGHT” darken the picture brighten the picture
“OFF” receive analog audio signal through L and R (component
“HUE”* increase red picture tones increase green picture tones video input) jack.
“SHARP” soften the picture sharpen the picture
* You can adjust “HUE” for the NTSC color system only.
2 Press to confirm the
– 22 –
selected option.
3 Repeat the above steps to adjust other items.
The adjusted settings will be received when you select “PERSONAL”.
Adjusting the “ADJUST” options under “SOUND MODE”

Note
1 Move up or down to • Your TV can only receive Dolby Digital or Linear PCM format digital
signals through the DIGITAL IN (component video input) jack
select the desired item
(e.g., “BALANCE”), then b b (see page 7). Receiving any other format digital signal may cause
unwanted noise or no sound from the speakers.
press . BALANCE 00
Tip
• For details on the menu system and how to use the menu, refer to
2 Adjust the value according to the following table, then press . “Introducing the menu system” on page 27.
For Move
“BASS” down or left to decrease the bass, up or right to increase the bass.
“TREBLE” down or left to decrease the treble, up or right to increase the treble.
“BALANCE” down or left to increase the left speaker’s volume, up or right to increase
the right speaker’s volume.
“BBE” up or down to select “HIGH”, “LOW”, or “OFF”.
“BBE” can produce clear sound.
3 Repeat the above steps to adjust other items.

The adjusted settings will be received when you select “PERSONAL”.
continued

Changing the Changing the “MULTI PICTURE” setting (continued)
“MULTI PICTURE” 3 Move up or down to

select the desired option
setting (see the table below), b
DRC-MF
then press .
The “MULTI PICTURE” menu allows VIDEO
you to use the Picture-in-Picture (PIP), Select To

TITLE
TWIN pictures, or PROGRAM INDEX “PIP” display the PIP screen within the main picture.
features. Move up or down to select “ON”, then press .
To cancel, press or select “OFF”, then press .
PROGR +
“PIP POSITION” change the position of the PIP screen.
PROGR – Move up or down to select the desired position, then press .
PIC SOUND
MODE MODE SURROUND
PROGR
FAVORITE INDEX
PROGR INDEX
. MENU PROGR
MENU
“SWAP” swap the main and PIP screens, or right and left pictures of the
TWIN pictures.
ENTER “TWIN” display a different TV program or video beside the main picture.
Move up or down to select “ON”, then press .
To cancel, press or select “OFF”, then press .
– 23 –
“PROGRAM INDEX” view multiple programs on the sub-screens.

To cancel, press PROGR INDEX.
TV
Press MENU.

DRC-MF: DRC1250
Tip
• For details on the menu system and how to use the menu, see
MENU b PICTURE MODE: DYNAMIC
SOUND MODE: DYNAMIC
SURROUND: OFF
“Introducing the menu system” on page 27.
DIGITAL IN : OFF
2 Move
select
up or down to
, then press .
MU L T I P I C T URE
P I P: OF F
b b P I P POS I T I ON :
SWA P
TW I N : OFF
PROGRAM I NDE X
continued
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Changing the Changing the “FEATURE” setting (continued)
“FEATURE” setting
DRC-MF
select the desired option
b
A/B
The “FEATURE” menu allows you to (see the table below),

change the size of the picture on the then press .
screen when receiving wide mode (16:9) 1 2 3
picture signals. You can also adjust the 4 5 6 Select To
picture setting that is suitable for 7 8 9 “WIDE MODE” change the size of the picture when receiving wide-mode (16:9)
viewing video games, and reduce the JUMP
picture signal.
0
power consumption of your TV.
PIC
MODE
SOUND
MODE SURROUND
PROGR
FAVORITE INDEX
MENU
MENU PROGR
b
ENTER
– 24 –
ENTER
PRESET VTR 1 2 3 DVD To restore the normal picture size, select “OFF” then press .
“ECO MODE” reduce power consumption of your TV to save energy.

To cancel, select “OFF”, then press .
TV
“GAME MODE” adjust the picture setting that is suitable to view video games.

DRC-MF: DRC1250
b
PICTURE MODE: DYNAMIC
MENU SOUND MODE: DYNAMIC Note
SURROUND: OFF
DIGITAL IN : OFF • When you turn on “ECO MODE”, the picture may become dimmer.
Turning “ECO MODE” off will restore the picture to its original setting.
• “WIDE MODE” and “GAME MODE” is available only when receiving
2 Move
select
up or down to
, then press .
FEATURE
W I D E M O D E : OF F
signals through the t (video input), (S video input), or
(component video input) jacks at the side and rear of your TV.
b b ECO MODE: OFF
GAME MODE: OFF Tip
• You can check if “ECO MODE” is turned on by checking its setting in the
menu or by pressing on the remote. If “ECO MODE” is on, then the
icon will appear on the bottom right corner of the screen.

Press MENU.
Tip
• For details on the menu system and how to use the menu, see
continued

Changing the “SET UP” setting (continued)
Changing the 1 2 3
“SET UP” setting 4 5 6 Number buttons Blocking channels (“CHILD LOCK”)
7 8 9
The “SET UP” menu allows you to: 0
JUMP
1 After selecting “CHILD
LOCK”, either move up
change the menu language, block PIC SOUND
or down, or press the b
channels, adjust the picture position, MODE MODE SURROUND
number buttons (or SE T UP
program your favorite channels, and FAVORITE
PROGR
INDEX
PROGR +/–) to select the L ANGUAGE : E
adjust the volume automatically.
MENU PROGR
MENU desired channel (e.g. PR 06),
then press .
or b b CH I L D LOCK PR 0 6
P I C ROT A T I
F A VOR I T E C ON
1 2 3
I NT E L L I GEN OF F
4 5 6
ENTER 7 8 9
ENTER JUMP

DRC-MF: DRC1250
MENU b PICTURE MODE: DYNAMIC
SOUND MODE: DYNAMIC
SURROUND: OFF
select “ON”, then
press .
S E T UP
DIGITAL IN : OFF To unlock the channel, LANGUAGE : ENG L I SH
select “OFF”.
2 Move up or down to S E T UP
LANGUAGE : ENG L I SH The lock symbol ( )
b b CH I L D L OCK : PR 0 6 ON
P I C ROT A T I ON
F A VOR I T E CH
select , then press .
b b CH I L D L OCK : PR 0 1 OF F
P I C ROT A T I ON appears on the screen when I N T E L L I GEN T VO L : OF F
– 25 –
F A VOR I T E CH “ON” is selected.

I N T E L L I GEN T VO L : O F F
If a locked channel is 6
select the desired option,
then press . b selected, the lock symbol
appears on the screen.
Select To
“LANGUAGE” change the menu language (see page 12).
“CHILD LOCK”
“PIC ROTATION”
block channels (see page 38).
adjust the picture position when it is not aligned with the TV screen.
3 Repeat steps 1 and 2 to lock other channels.
Move up or right to adjust the position clockwise, then press .

Move down or left to adjust the position counterclockwise, then
press . To return to the normal screen
Press MENU.
b b
PIC ROTATION
Note
• If you preset a locked channel, that channel will be unlocked (see page 40).
“FAVORITE CH” select your favorite channels (see pages 16 and 39).
“INTELLIGENT adjust the volume of each TV program automatically.
VOL” Move up or down to select “ON”, then press .
To return to the normal screen continued
Press MENU. Adjusting Your Setup (MENU) 37 38 Adjusting Your Setup (MENU)
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Changing the favorite channel setting Changing the “CH FAVORITE
PROGR
INDEX
PRESET” setting MENU

1 After selecting “FAVORITE
CH”, make sure “MODE”
F A VOR I T E CH
MODE : AU TO AU TO
MENU PROGR
is selected, then press . b 1 . PR 0 1

2 . PR 0 2
3 . PR 0 6
MANUA L
The “CH PRESET” menu allows you to
adjust the setup of your TV. For ENTER
ENTER
4 . PR 0 8
example, you can manually tune in a PRESET VTR 1 2 3 DVD
channel with a weak signal that fails to

select “MANUAL”, then
F A VOR I T E CH
MODE : MANUA L be tuned in by automatic presetting.
PRESET
press . b b 1 . PR 0 1
2 . PR 0 2
3 . PR 0 6
5 . PR 0 9
6 . PR 1 1
7 . PR 1 3
4 . PR 0 8
DRC-MF: DRC1250
3 Move up or down to F A VOR I T E CH MENU b PICTURE MODE: DYNAMIC

SOUND MODE: DYNAMIC
SURROUND: OFF
select the program you MODE : MANUA L
DIGITAL IN : OFF
want to change, then
press .
b b 1 . PR 0 1
2 . PR 0 2
5 . PR 0 9
6 . PR 1 1
3 . PR 0 6
4 . PR 0 8
7 . PR 1 3
2 Move up or down to CH PRE S E T
AU TO PROGRAM
select , then press .
b b MANUA L PROGRAM
– 26 –
S K I P : PR 0 2 OF F
change the number, then
F A VOR I T E CH
MODE : MANUA L
TV SYS : B / G
CO L S Y S : AU TO
press . b b 1 . PR 0 1
2 . PR 0 2
5 . PR 0 9
6 . PR 1 1
3 . PR 0 5 7 . PR 1 3
b
4 . PR 0 8 select the desired option,
then press .
5 Repeat steps 3 and 4 to set other channels.
Select To
“AUTO PROGRAM” preset channels automatically.
“MANUAL PROGRAM” preset channels manually. See “Presetting channels
Press MENU. manually” on page 41.
Note “SKIP” skip unwanted or unused channels.
• If you press the PROGR +/– buttons or number buttons in step 4 above, 1 Either move up or down, or press the number buttons
the TV will display the channel immediately. (or PROGR +/–) until the unused or unwanted channel
number appears, then press .
2 Select “ON”, then press .
3 To disable other channels, repeat steps 1 and 2.
To restore the skipped channel, select “OFF” in step 2.
“TV SYS” select the TV system.
“COL SYS” select the color system. Normally, set this to “AUTO”.

Press MENU.
Tip
• For details on the menu system and how to use the menu, refer to

Changing the “CH PRESET” setting (continued)
Presetting channels manually
1 After selecting “MANUAL

PROGRAM”, select the
4 If you are not satisfied with
the picture and sound
program number to MANUA L PROGRAM quality, you may be able to
PR : 0 6 improve them by using the
which you want to preset TV SYS : B / G
a channel.
(1) Make sure “PR” is selected,
b S ENS : H I GH
VH F L OW
“FINE” tuning feature. MANUA L PROGRAM
PR : 1 0 AU TO
(1) Move up or down
then press .
F I NE : AU TO
to select “FINE”, then
press .
b b TV SYS : I
S ENS : H I G
VH F L OW
MANUA L
(2) Move up or down until F I NE :

the program number you MANUA L PROGRAM
PR : 1 0
want to preset (e.g., MANUA L PROGRAM
program number “10”) b b TV SYS : B / G
S ENS : H I GH
(2) Move up or down PR : 1 0 AU TO
appears on the menu, VH F L OW
F I NE : AU TO
to select “MANUAL”,
then press . b b TV SYS : I
S ENS : H I G
MANUA L
then press . VH F L OW
F I NE :
Tips
(3) Move either up,
• You can also select the “MANUAL PROGRAM” menu directly by pressing the
PRESET button on the remote. down, left or right MANUA L PROGRAM
• You can also select the program number with the PROGR +/– or number buttons.
until the picture PR : 1 0
and sound quality are
b b TV SYS : I
S ENS : H I GH
2 Select the desired channel.
MANUA L PROGRAM
optimal, then press
The + or – icon on the
. VH F L OW
F I NE : MA NU A L
(1) Move up or down to PR : 1 0 menu flashes while
select either “VHF LOW”,
“VHF HIGH”, or “UHF”, b b TV SYS : B / G
S ENS : H I GH tuning.
– 27 –
VH F L OW
then press .
(2) Move up or down
F I NE : AU TO
5 If the TV signal is too
strong and the picture is
MANUA L PROGRAM
until the desired PR : 1 0 distorted, you can adjust
channel’s broadcast
appears on the TV
b b TV SYS : B / G
S ENS : H I GH
VH F L OW
the TV reception
sensitivity.
MANUA L PROGRAM
PR : 1 0 H I GH
TV SYS : I
screen, then press . F I NE : AU TO (1) Move
to select “
up or down
SENS”,
b b S ENS :
VH F L OW
L OW
F I NE : MA NU A
3 If the sound of the
desired channel is
then press .
abnormal, select the MANUA L PROGRAM

(2) Move up or down PR : 1 0
appropriate TV system.
(1) Move up or down to
MANUA L PROGRAM to select “LOW”, then b b TV SYS : I
S ENS : L OW
PR : 1 0 B/G press . VH F L OW
select “TV SYS”, then
press .
b b TV SYS : I
S ENS : H I G D / K
VH F L OW M
F I NE : MA NU A L
F I NE : AU TO
MANUA L PROGRAM
(2) Move up or down PR : 1 0 Press MENU.
until the sound
becomes normal, then b b TV SYS : I
S ENS : H I GH Notes
VH F L OW
press . F I NE : AU TO
• The TV system (“TV SYS”) and the TV reception sensitivity (“ SENS”)
settings are memorized for each program number.
• If you preset a locked channel, that channel will be unlocked (see page 38).
continued
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Additional Information
Self-diagnosis function Troubleshooting

Your TV is equipped with a self-diagnosis function. If there is a If you have any problem while viewing your TV, please check the following
problem with your TV, the 1 (standby) indicator flashes red. The troubleshooting guide. If the problem persists, contact your Sony dealer.
number of times the 1 indicator flashes indicates the possible Possible cause
Symptom Solutions Page
causes.
Snowy picture • The connection is • Check the antenna cable and 4
loose or the cable is connection on the TV, VCR and at the
damaged. wall.
Front of TV
• Channel presetting • Press the PRESET button to display 41
is inappropriate or the “MANUAL PROGRAM” menu
incomplete. and preset the channel again.
Noisy sound
• The antenna type is • Check the antenna type (VHF/UHF). –
inappropriate. Contact a Sony dealer for advice.
• The antenna • Adjust the antenna direction. Contact –
direction needs a Sony dealer for advice.
1 indicator adjustment.
• Signal transmission • Try using a booster. –
is low.
– 28 –
U Distorted picture • Broadcast signals • Press the PRESET button to display 42

are too strong. the“MANUAL PROGRAM” menu.
Then, select “ SENS: LOW”.
• Turn off or disconnect the booster if it –
is in use.
Noisy sound
1 Check that the 1 indicator flashes red a number of times between 3-second
intervals.
Good picture • The TV system • If the sound of all the channels are noisy, 40
setting is display the “CH PRESET” menu and
2 Count the number of times the 1 indicator flashes.
inappropriate. select “AUTO PROGRAM” to preset the
channels again.
3 Press ! (main power) to turn off your TV. • If the sound of some channels is noisy,
select the channel, then display the
41
Additional Information
Noisy sound
“CH PRESET” menu and select the
4 Inform your nearest Sony service center about the number of times the
1 indicator flashed.
appropriate TV system (“TV SYS”).
• The digital audio • Set “DIGITAL IN: OFF” in the “A/V 7, 32
Be sure to note the model name and serial number located on the rear of
signal is CONTROL” menu and connect L
your TV. inappropriate. and R (component video input) on your
TV to receive analog audio signals.
No picture • The power cord, • Check the power cord, antenna and 4
antenna or VCR is the VCR connections.
not connected.
• The TV is not turned • Press I/1 (power). 10
on. • Press U (main power) on the TV to 11
No sound turn off the TV for about five
seconds, then turn it on again.
Additional Information 43 44 Additional Information

Troubleshooting (continued)
Symptom Possible cause Solutions Page
Good picture • The volume level is • Press ¸ + to increase the volume 11
too low. level. Symptom Possible cause Solutions Page
• The sound is muted. • Press ¤ to cancel the muting. 11 TV cannot receive • The stereo reception • Press A/B until “AUTO” appears on 23
stereo broadcast setting is inappropriate. the screen.
• The broadcast signal • Press A/B until a better sound is 23 signal.
has a transmission heard.
No sound problem. Stereo broadcast • The connection is loose • Check the antenna cable and 4
sound switches or the cable is damaged. connection on the TV, VCR and on the
• The digital audio • Set “DIGITAL IN: OFF” in the “A/V 7, 32 on and off or wall.
signal is CONTROL” menu and connect L is distorted.
and R (component video input) on your • The antenna direction • Adjust the antenna direction. Contact a –
inappropriate. or needs adjustment. Sony dealer for advice.
TV to receive analog audio signals.
• When connecting to (component
The sound switches • The broadcast signal • Press A/B until a better sound is heard. 23
• The “DIGITAL IN” 32
between stereo and has a transmission
setting in the “A/V video input) on your TV, set “DIGITAL
monaural frequently. problem.
CONTROL” menu is IN: ON” to receive digital audio signals
inappropriate. through DIGITAL IN, or set Picture slant • Terrestrial magnetism is • Display the “SET UP” menu and adjust 37
“DIGITAL IN: OFF” to receive analog
affecting your TV set. “PIC ROTATION” so that the picture is
audio signals through L and R.
aligned to the TV screen.
Dotted lines or • There is local • Do not use a hair dryer or other –
stripes interference from equipment near the TV.
cars, neon signs, hair
dryers, power • Adjust the antenna direction for –
minimum interference. Contact a Lines moving across • There is interference • Use the fine tuning (“FINE”) function. 42
generators, etc.
Sony dealer for advice. the TV screen. from external sources,
e.g., heavy machineries,
– nearby broadcast station.
– 29 –
Double images or • Broadcast signals are • Use a highly directional antenna.

“ghosts” reflected by nearby The 1 indicator on • Your TV may need • Contact your nearest Sony service 43
mountains or buildings. • Use the fine tuning (“FINE”) function. 42
your TV flashes red servicing. center.
– a number of times
• The antenna direction • Adjust the antenna direction. Contact
between 3-second
needs adjustment. a Sony dealer for advice. intervals.
• Use of a booster is • Turn off or disconnect the booster if it – TV cabinet creaks. • Changes in room
inappropriate. is in use. temperature sometimes
No color • The color level make the TV cabinet — –
• Display the “A/V CONTROL” menu and 31
setting is too low. expand or contract,
select “ADJUST” of “PICTURE MODE”, causing a noise. This
then adjust the “COLOR” level. does not indicate a
• The color system setting • Display the “CH PRESET” menu and 40 malfunction.
is inappropriate. check the color system (“COL SYS”)
A small “boom” • The TV’s demagnetizing
setting (usually set this to “AUTO”). function is working.
sound is heard
• The antenna direction This does not indicate a — –
• Adjust the antenna direction. Contact – when the TV is
needs adjustment. a Sony dealer for advice. turned on. malfunction.
Abnormal color • The magnetic • Locate external speakers or other – Static discharge is • This is the same static
patches disturbance from equipment away from the TV. Do not felt when touching discharge that is felt
external speakers or move the TV while the TV is turned the TV cabinet. when touching metal
other equipment, or on. Press U (main power) on the TV door handles or car — –
the direction of the to turn off the TV for about five doors especially when
earth’s magnetic field minutes, then turn it on again. the air is dry, for
may affect the TV. example in winter. This
does not indicate a
continued malfunction.
KV-ES29M90
RM-916

KV-ES29M90
RM-916
Identifying parts and controls (continued)
Identifying parts and controls
Front, top and side panels Remote control The names/symbols of buttons on the remote are
Top panel indicated in different colors to represent the available
MENU ENTER … – . + – PROGR +
DRC-MF functions.
A/B Label color Button function

White For general TV operations
Side panel
Green For Teletext operations
1 2 3
4 5 6 Yellow For PIP operations
2
7 8 9
JUMP
0 Button Function Page

PIC SOUND
MODE MODE SURROUND
I/1 Turn off temporarily or 10
…4 FAVORITE
PROGR
INDEX turn on the TV.
L Front panel
(MONO) PROGR +/– Select program number. 10
≥ MENU PROGR
R 0 – 9, ÷ Input numbers. 10
– 30 –
g
AUTO Display on-screen information. 11
PROGR U
ENTER
¤ Mute the sound. 11
; Display the TV program. 11
t Select TV or video input. 11

. +/– Adjust volume. 11
JUMP Jump to previous channel. 11
Button Function Page Timer operations
TV Set TV to turn on automatically. 13
Side panel
Set TV to turn off automatically. 13
i Headphone jack. –
SOUND MODE Select sound mode. 14
AUTO PROGR Preset channels automatically. 5
PIC MODE Select picture mode. 14
Front panel Select DRC-MF mode. 15
Turn off completely or 10 DRC-MF
!
turn on the TV. Favorite Channel operations
Top panel FAVORITE Display favorite channels. 16
I/1 Turn off temporarily or 10 DRC-MF
Select desired channel. 16
turn on the TV.
PROGR +/– Select program number. 10 VIDEO
PIP and Twin picture operations
2 +/– Adjust volume. 11 TITLE
Display the PIP screen. 17
t Select TV or video input. 11 Display TWIN pictures. 17
ENTER Confirm selected items. 29 Adjust Twin picture size. 18
MENU Display the menu. 29 PROGR +/ Change program in PIP/ 18
PROGR +
PROGR – Twin picture.
PROGR –
Select video input for PIP/ 18
Twin picture.
PIC
MODE
SOUND
MODE SURROUND
Swap main and PIP/Twin 18
picture.
PROGR
FAVORITE INDEX
Freeze PIP screen. 18
continued A Adjust position of PIP screen. 18

DRC-MF Button Function Page
A/B
Program Index operations
PROGR INDEX Display all preset TV 19
programs.
1 2 3 PROGR +/– View next/previous 12 TV 20
programs.
4 5 6
Select desired channel. 20
7 8 9 Select surround mode. 22
JUMP SURROUND
0 A/B Select stereo/bilingual mode. 23
PIC SOUND
MODE MODE SURROUND
Teletext operations
FAVORITE
PROGR
INDEX (not used for this model)
Display Teletext broadcast. –
MENU PROGR
Display Teletext service contents. –

Stop Teletext page from scrolling. –
ENTER Reveal concealed information. –
Enlarge the Teletext display. –
Show TV screen while waiting –
for Teletext page.
0-9 Input Teletext page number. –
PROGR +/– Display the next or previous page. –
TV (red, green, Access a FASTEXT menu. –
– 31 –
yellow, blue)
Optional components operations
VTR Set up the remote. 25
VIDEO I / 1 Power. 26
TITLE Display the title menu. 26
( Play. 26
+ Fast forward/Search forward. 26
DRC-MF
= Rewind/Search backward. 26
VIDEO
r Record. 26
TITLE
p Stop. 26
P Pause. 26
Menu operations
MENU Display the menu. 29
PROGR +
Select, adjust and confirm 29

PROGR –
selected items.
ENTER Confirm selected items. 29
PIC SOUND
MODE MODE SURROUND
PRESET Display “MANUAL 41
FAVORITE
PROGR
INDEX PROGRAM” menu.
Additional Information 49
KV-ES29M90
RM-916

KV-ES29M90
SECTION 2
RM-916
DISASSEMBLY
2-1. REAR COVER REMOVAL 2-3. H2 BOARD REMOVAL

Caution: Please make sure that the red colour taped point is just placed with the
purse lock when treating the leads to H2 board. If lead treatment is wrongly
arranged, it will affect the door opening and closing malfunction.
Eight screws
(+BVTP 4X16)
Red tape
– 32 –
1 One screw
(+BVTP 4X20)
2-2. SPEAKER BOX REMOVAL 1 One spring
3 H2 Board
2 Two screws
(+BVTP 3X25)
2 SPEAKER BOX
L/R ASSEMBLY
4 Two shafts
5 Two screws
(+BVTP 3X12)
1Two screws
(TP + TWH 4X25)

DH board
2-4. CHASSIS ASSY REMOVAL 2-6. DH BOARD REMOVAL
1Four screws
(+BVTP 3X12)
Blacket
CRT Supporter
Chassis
2-7. J BOARD REMOVAL
– 33 –
Metal Case
2-5. SERVICE POSITION
5 J sheild cover
4 J board
1Two screws
(+BVTP 3X12)
A board
2 Four screws
(+BVTP 3X12)
D board
1Three screws
KV-ES29M90
(+BVTP 3X12)
RM-916
3Terminal bracket

KV-ES29M90
2-8. B3, D1 AND E BOARDS REMOVAL 2-10. H1 BOARD REMOVAL
RM-916
NOTE: V board is not used for this model. NOTE : Push the hook down using the tip of a screwdriver and at the same time
pull the H1 bracket.
1Three screws
(+BVTP 3X12)
Driver
6 Metal Case P board

V board
8 E board
7 D1 board
5 V board Driver
4 B3 board 1
H1 bracket
2 Two connectors
– 34 –
2-11. F2 BOARD REMOVAL

3 Two connectors
NOTE : To remove F2 board, firstly remove the H1 board. Then, push the hook
down using the tip of a screwdriver and at the same time pull the F2
2-9. A AND D BOARDS REMOVAL bracket.
Caution : When removing the F2 board, please turn off the main AC supply.
1 Four screws 1Three connectors
(+BVTP 3X12) 2A board
3 D board
Driver
F2 bracket

2-12. DEMAGNETIZATION COIL REMOVAL 2-14. G2 LEAD REMOVAL
NOTE : Insert pin to both edge holes on socket and release the lock.
5Two DGC holders

2
2DGC band
1 Pin
4Demagnetization
coil
1Two DGC clips
2-13. TOP SWITCH REMOVAL (H3 BOARD REMOVAL)

– 35 –
NOTE : To remove H3 board, the CRT has to be removed first.
3 H3 board
2 H3 bracket
4 Top switch
1 Two screws
(+BVTP 4X12)
KV-ES29M90
RM-916

KV-ES29M90
2-15. PICTURE TUBE REMOVAL 2-16. FRAME SUB-ASSY DISASSEMBLY
RM-916
NOTE : Prior to picture tube removal, please remove the front cover first. 1
Caution : Aluminium frame is easily scratched if extra caution is not taken when han-
dling it.
Screw Special (Dia. 8)
(+) TP 4 × 9
5 Chassis assembly ×1 ×1
×2 ×2
7 C board
!™ Two DGC clips

8 Neck assembly
9 Deflection yoke
9 Two springs
2Speaker box(L)
assembly 4 Two claws
1Two screws
(TP+TWH 4X25) !¡Two fooks
Fasten
6 Four screws
– 36 –
(+BVTP 4X25) ×1
×1
Screw Machine (8)
(K 4 × 10)
×2 ×2
!∞ Demagnetization ×1 ×1
coil
!¢ DGC band 1 Two screws
CRT Bracket
!£ Two DGC holders (TP+TWH 4X25)
3 Anode cap
!§ Four screws
!¶ Picture tube
2 Speaker box(R)
Cushion assembly

2 FRAME SUB ASSY, RIGHT REMOVAL Screw Special (Dia. 8)
(+) TP 4 × 9
×2
Slide
×2
Corner Block Screw Special (Dia. 8)

(+) TP 4 × 9
– 37 –
FRAME SUB ASSY, TOP REMOVAL

FRAME SUB ASSY, LEFT REMOVAL ×2
a)
(+) TP 4 × 9
(+) TP 4 × 9
Slide
×2
Slide
b) Corner Block
×2
KV-ES29M90
(+) TP 4 × 9
×4 ×4
Screw Special (Dia. 8) Screw Special (Dia. 8)

RM-916
(+) TP 4 × 9 (+) TP 4 × 9

KV-ES29M90
FRAME SUB ASSY, BOTTOM REMOVAL • REMOVAL OF ANODE-CAP
RM-916
a)
NOTE : After removing the anode, short circuit the anode of the picture tube and
the anode cap to the metal chassis, CRT shield or carbon paint on the
CRT.
• REMOVING PROCEDURES
a
(+) TP 4 × 9 a
×2 1 Turn up one side of the rubber cap in the direction indicated by the arrow a.
b
Slide
b
Corner Block
b)
2 Using a thumb pull up the rubber cap firmly in the direction indicated by the arrow b.
– 38 –
×4 ×4
Screw Special (Dia. 8) Screw Special (Dia. 8)

(+) TP 4 × 9 (+) TP 4 × 9 Anode button
3 When one side of the rubber cap is separated from the anode button, the anode-cap
NOTE : When replacing the Frame Sub-Assy Top and Bottom, fix the original corner can be removed by turning up the rubber cap and pulling it up in the direction of the
block to the new part. arrow c.
• HOW TO HANDLE AN ANODE-CAP

1 Do not damage the surface of anode-caps with sharp shaped objects.
2 Do not press the rubber too hard so as not to damage the inside of anode-cap.
A metal fitting called the shatter-hook terminal is built into the rubber.
3 Do not turn the foot of rubber over too hard.
The shatter-hook terminal will stick out or damage the rubber.

KV-ES29M90
SECTION 3 RM-916
SERVICE JIG
3-1. JIGS REQUIRED FOR SERVICING
REF NO. DESCRIPTION PART NO. REMARK

J-1 TOOL (20P), SERVICE 3-702-763-01 For A to V board extension
J-2 TOOL (40P), SERVICE 3-702-764-01 For A to E board extension
J-3 TOOL (50P-A), SERVICE 3-702-765-01 For A to B3 board extension
J-4 TOOL (50P-J), SERVICE 3-702-766-01 For A to J board extension
For D to D1 board extension
J-1 J-2
EX3 EX4
EX1 EX2
J-3 J-4
EX5 EX7
EX6 EX8
– 39 –
KV-ES29M90
RM-916 SECTION 4
SET-UP ADJUSTMENTS
• The following adjustments should be made when a complete Perform the adjustments in the following order :
realignment is required or a new picture tube is installed. 1. Beam Landing
• These adjustments should be performed with rated power 2. Convergence
supply voltage unless otherwise noted. 3. Focus
4. White Balance
Controls and switches should be set as follows unless otherwise noted: Note : Test Equipment Required.
PICTURE control ........................................................... normal 1. Color-bar/Pattern Generator
BRIGHTNESS control ................................................... normal 2. Degausser
3. Oscilloscope
................................................................................................................................................................................................................................
Preparation :
• In order to reduce the influence of geomagnetism on the set's
picture tube, face it east or west.
• Switch on the set's power and degauss with the degausser.
4-1. BEAM LANDING

1. Input a white signal with the pattern generator.
Contrast
Brightness
normal
} Fig. 4-2
2. Position neck assy as shown in Fig4-1.

3. Set the pattern generator raster signal to a green raster.
Blue
4. Move the deflection yoke to the rear and adjust with the purity
Red
control so that the green is at the center and the blue and the red
take up equally sized areas on each side. Green
(See Figures 4-1 through 4-3.)
5. Move the deflection yoke forward and adjust so that the entire
Fig. 4-3
screen is green. (See Figure 4-2.)
Purity control
6. Switch the raster signal to blue, then to green and verify the corrects this area.
Disk magnets or rotatable
condition.
disk magnets correct these
7. When the position of the deflection yoke has been decided, areas (a-d).
b a
fasten the deflection yoke with the screws and DY spacers.
8. If the beam does not land correctly in all the corners, use a
c d
magnet to adjust it.
(See Figure 4-4.)
Deflection yoke positioning
Neck assy corrects these areas.
c
Behind the G2 edge
a
G1 G2 G3
Fig. 4-1 Fig. 4-4
– 40 –
KV-ES29M90
RM-916
4-2. CONVERGENCE ADJUSTMENT 1 V. STAT

Preparation : a b
• Before starting this adjustment, adjust the focus, horizontal size
a
and vertical size. B B
• Set the PICTURE 70% and BRIGHTNESS 0%. b b
G G
• Cross hatch / Dot pattern.
R R
(1) Horizontal and Vertical Static Convergence
2 H. STAT VR
Center dot
R a
G
B
R G B R G B
V. STAT
H. STAT VR Magnet
b
B G R
Y magnet
3
RV702
H. STAT a b
b a
R B
G G
C Board b B R
1. (Moving horizontally), adjust the H.STAT control so that the

red, green and blue dots are on top of each other at the center of
the screen. BMC (Hexapole)
2. (Moving vertically), adjust the V.STAT magnet so that the red, Purity
green and blue dots are on top of each other at the center of the
screen.
3. Adjust Horizontal Trapezoid with “DAC 04 HTR” in Service
Mode to make H-Trapezoid distortion best.
4. If the H.STAT variable resistor cannot bring the red, green and
blue dots together at the center of the screen, adjust the
horizontal convergence with the H.STAT variable resistor and
the V.STAT magnet in the manner given below. V.STAT
(In this case, the H.STAT variable resistor and the V.STAT
magnet influence each other, so be sure to perform adjustments
while tracking.)
– 41 –
KV-ES29M90
RM-916
4 BMC (Hexapole) Magnet. (2) Dynamic Convergence Adjustment

If the red, green and blue dots are not balanced or aligned, then Preparation:
use the BMC magnet to adjust in the manner described below. • Before starting this adjustment, adjust the horizontal static
R G B R G B R G B convergence and the vertical static convergence
• Set the PICTURE and BRIGHTNESS to normal.
1. Adjust TLH. (TLH correction piece)

1 Receive the dot/hatch pattern signal and adjust picture quality
by the menu.
2 Correct horizontal mis-convergence of red and blue of both sides
R B
G R G B G on the X axis.
R B
When red is outside insert BMC magnet to right side (THL+)
views from DY neck. And when blue is outside, insert it to left
side (THL–) and take both sides.
R B B R TLH +
(B) (R) (R) (B) TLH -
5 Y separation axis correction magnet adjustment.

1. Receive the cross-hatch signal and adjust [PICTURE] to [MIN]
and [BRIGHTNESS] to [STANDARD] .
2. Adjust the Y separation axis correction magnet on the neck 2. Adjust XCV core.
assembly so that the horizontal lines at the top and bottom of To able to become balance of XCV on the X axis well.
the screen are straight. 3. Adjust V-TILT.
Blue Red Correct the vertical mis-convergence of red and blue of verti-
Neck assy Neck assy
cally sides on the Y axis.
4. Adjust YCH.
Adjust horizontal mis-convergence of red and blue of verti-
cally sides on the Y axis. Mentioned above steps 2 to 4 are
adjusting respectively perform minuteness tracking.
Red Blue
YCH
TLV1
VM board VM board
TLV2 XCV
BMC magnet C board
RV9001
Note
1. The Red and Blue magnets should be equally far from the
horizontal center line.
2. Do not separate the Red and Blue magnets too far. (Less than VM board
8 mm)
– 42 –
KV-ES29M90
RM-916
(3) Screen-corner Convergence 4-3. FOCUS ADJUSTMENT

Note
Focus adjustment should be completed before W/B adjustment.
b a (1) Receive digital monoscope pattern.

a-d : screen-corner
(2) Set "A/V CONTROL" to "STANDARD".
misconvergence (3) Adjust FOCUS VR so that the center of the screen becomes
justfocus.
c d (4) Change the receiving signal to white pattern and blue back.
(5) Confirm MAGENTA RING should not be over the limit.
In case MAGENTA RING is over the limit sample, adjust FO-
CUS VR to take tracking of MAGENTA RING and FOCUS.
Fix a Permalloy assy corresponding to the misconverged

areas.
b
Focus
d
Permalloy assembly c
Screen
(No Function)
FLYBACK TRANSFORMER (T6803)
4-4. NECK ASSY TWIST ADJUSTMENT

(1) Receive dot/hatch pattern.
(2) Turn FOCUS VR fully counter-clockwise.
(3) Confirm the dot shape at the screen center. (Fig. 4-4)
(4) Resume FOCUS VR.
Note
In case of turning NECK ASSY, loosen the screw 3 turns. Do not
move the position.
OK
Turn NECK ASSY clockwise.
Turn NECK ASSY counter clockwise.
Fig. 4-4
– 43 –
KV-ES29M90
RM-916
4-5. G2 (SCREEN) AND WHITE BALANCE 3. SUB PICTURE BRIGHTNESS ADJUSTMENT

1) Tune RF PAL white signal at program No. 1 and No. 2.
ADJUSTMENTS
2) Select “TWIN PICTURE” mode.
1. G2 (SCREEN) ADJUSTMENT 3) Receive different RF PAL white signals in MAIN and Sub
1) Set the PICTURE and BRIGHTNESS to normal. picture.
2) Put to VIDEO input mode without signals. 4) Adjust RV3300 on A PWB, so that the output from the 17 pin
3) Connect R, G and B of the C board cathode to the oscilloscope. and 20 pin of the CN1180 becomes within the spec.
4) Adjust BRIGHTNESS to obtain the cathode voltage to the value
below. CVBS 1
5) Whilst watching the picture, adjust the screen VR (RV9002) 17 pin
located on the C board to the point just before the flyback return MAIN
lines disappear (to the point before cut-off).
170 V ± 2 (VDC)
0V
2. WHITE BALANCE ADJUSTMENT CVBS 2

1) Set to Service Mode (Refer Section 5-1: ADJUSTMENTS 20 pin
WITH COMMANDER). SUB
2) Input white raster signal.
3) Set the following condition.
PICTURE minimum, BRIGHTNESS 50% B
4) Select GCT (WHB 7) and BCT (WHB 8) with [1] and [4], and
adjust the level with [3] and [6] for the best white balance.
5) Set the PICTURE to maximum.
6) Select GDR (WHB 4) and BDR (WHB 5) with [1] and [4], and Spec: |A - B| ≤ ± 20mV
adjust the level with [3] and [6] for the best white balance.
7) Write into the memory by pressing [MUTING] then [0].
– 44 –
KV-ES29M90
SECTION 5 RM-916
CIRCUIT ADJUSTMENTS
5-1. ADJUSTMENTS WITH COMMANDER

Service adjustments are made with the RM-916 that comes with
this unit. 1, 4 Select the adjustment item.
a. ENTERING SERVICE MODE ↓
3, 6 Raise/lower the data value.
With the unit on standby ↓
↓ [MUTING] Writes.
[DISPLAY] ↓
↓ - Executes the writing.
5
↓ 7, - All the data becomes the values in memory.
VOL (+) 8, - All user control goes to the standard state.
↓ 5, - Service data initialization (Be sure not to use
[POWER] usually.)
This operation sequence puts the unit into service mode. [DISPLAY], - Write 50Hz adjustment data to 60Hz, or vice
versa.
b. METHOD OF CANCELLATION FROM SERVICE 2, - Copy and write all data.
MODE
Set the standby condition (Press [POWER] button on the commander),
then press [POWER] button again, hereupon it becomes TV mode. DRC-MF
A/B
c. METHOD OF WRITE INTO MEMORY
1) Set to Service Mode.
2) Press [1] (UP) and [4] (DOWN), select an item of adjustment. 1 2 3
3) Press [MUTING] button and it will indicate WRITE on the screen. 4 5 6
4) Press [0] button to write into memory. 7 8 9
JUMP
0
d. MEMORY WRITE CONFIRMATION METHOD PIC
MODE
SOUND
MODE SURROUND
1) After adjustment, pull out the plug from AC outlet, and then FAVORITE
PROGR
INDEX
plug into AC outlet again. MENU PROGR
2) Turn the power switch ON and set to Service Mode.

3) Call the adjusted items again to confirm adjustments were made.
ENTER
The screen display is :

Device Name Item Name Marking of virgin NVM
Item No Data Mode

TV
GEO 00 VSZ 29 p SERVICE p 50 PAL, SECAM : 50
NTSC : 60
0 012Q 1.2M 59 FF 000A RM-916
Suffix No
(OEM Code)
Software version Total Power-On time (hours)
– 45 –

KV-ES29M90
RM-916
5-2. ADJUSTMENT METHOD

Item Number 00 of device GEO
This explanation uses H-Position as an example. Use the same method for all Items. Use 1 and 4 to select the
1. Select “GEO 00 VSZ” with the 1 and 4 buttons. adjustment item, use 3 and 6 to adjust, write with [MUTING],
2. Raise/lower the data with the 3 and 6 buttons. then execute the write with -.
3. Select the optimum state. (The standard is 1F for PAL reception.)
4. Write with the [MUTING] button. (The display changes to Note : 1. In [WRITE], the data for all items are written into memory
WRITE.) together.
5. Execute the writing with the - button. (The WRITE 2. For adjustment items that have different standard data
display will be changed to red color while excuting, and back between 50Hz or 60Hz, be sure to use the respective
to SERVICE.) input signal after adjustment.
3. Additional function to skip category (device) to category
GREEN
(device).
GEO 00 HPS 29 SERVICE 50
0 012Q 1.2M 59 FF 0 000A example:
Adjusted with [3] GEO 00 HPS
and [6] buttons.
↕
DAC 00 XXX
The buttons for the function above should be cursor +/–.
GEO 00 HPS 1F WRITE 50 GREEN

0 012Q 1.2M 59 FF 0 000A
Written with [MUTING]
GEO 00 HPS 1F SERVICE 50 RED

0 012Q 1.2M 59 FF 0 000A The WRITE display
then the display
returns to a green
SERVICE.
Write executed with [0]
– 46 –

Adjustment Item Table
Category Functionality Initial Range Function Table & Note Register Device & Slave RAM Address
No. Name Data (Bit Range) Address (Bit Range)
GEO 00 VSZ 21 3F V SIZE FF/R4/PR*50/60*VC/NC, TW/IX 11 (7-2) CXA2100AQ (86H) 369 (7-2)
01 VPS 27 3F V POSITION FF/R4/PR*50/60*VC/NC, TW/IX 12 (7-2) 354 (7-2)
02 VLN 5 0F V LINEARITY FF/R4/PR*50/60*VC/NC 13 (7-4) 95 (3-0)
03 SCO 0A 0F S CORRECTION FF/R4/PR*50/60*VC/NC 13 (3-0) 95 (7-4)
04 HSZ 1E 3F H SIZE FF/R4/PR*50/60*VC/NC, TW/IX 14 (7-2) 36A (7-2)
05 HPS 2F 3F H POSITION FF/R4/PR*50/60*VC/NC, TW/IX 19 (7-2) 355 (7-2)
06 PAP 28 3F PIN AMP FF/R4/PR*50/60*VC/NC 15 (7-2) 98 (7-2)
07 UPN 25 3F UPPER CORNER PIN FF/R4/PR*50/60*VC/NC 16 (7-2) 99 (7-2)
08 LPN 23 3F LOWER CORNER PIN FF/R4/PR*50/60*VC/NC 17 (7-2) 9D (7-2)
09 TRZ 0C 0F TRAPEZIUM FF/R4/PR*50/60*VC/NC, TW/IX 18 (7-4) 36B (7-4)
0A AGL 0A 0F AFC ANGLE FF/R4/PR*50/60*VC/NC 1A (3-0) 9B (3-0)
0B BOW 6 0F AFC BOW FF/R4/PR*50/60*VC/NC 1A (7-4) 9B (7-4)
0C LBL 12 3F LEFT H BLANKING FF/R4/PR*50/60*VC/NC, TW/IX 1B (7-2) 9C (7-4)
0D RBL 2C 3F RIGHT H BLANKING FF/R4/PR*50/60*VC/NC, TW/IX 1C (7-2) 9C (3-0)
0E MPN 0 3 MIDDLE PIN DISTORTION COMPENSATION 50/60*VC/NC 16 (1-0)
0F UVL 0 0F UPPER V LINEARITY 50/60Hz 1F (7-4)
10 LVL 0 0F LOWER V LINEARITY 50/60Hz 1F (3-0)
11 HCP 0 3 HORIZONTAL HIGH VOLTAGE COMPENSATION 50/60*VC/NC 15 (1-0)
12 VCP 1 3 VERTICAL HIGH VOLTAGE COMPENSATION 50/60*VC/NC 12 (1-0)
– 47 –
13 VAS 2F 3F V ASPECT 50/60*VC/NC 1D (7-2)

14 VSC 1F 3F V SCROLL 50/60Hz 1E (7-2)
15 USC 0 1 UNDER-SCAN MODE ON/OFF 50/60*VC/NC 1D (0)
16 VBW 0 3 V BLANKING WIDTH CONTROL FF/R4/PR*50/60*VC/NC 19 (1-0) 6D (1)
17 AT1 2 3 AKB REFERENCE TIMING FF/R4/PR*50/60*VC/NC 1E (1-0)
DAC 00 HCT 33 FF H CENTER 50/60Hz CH 10 (7-0) MB88141 (96H)
01 HLN 27 3F H LINEARITY FF/R4/PR*50/60*VC/NC CH 4 (7-2)
02 MDP 26 3F MIDDLE PIN FF/R4/PR*50/60*VC/NC CH 1 (7-2)
03 CCP 37 3F LOWER CORNER PIN FF/R4/PR*50/60*VC/NC CH 9 (7-2)
04 HTR 26 3F HORIZONTAL TRAPEZIUM FF/R4/PR*50/60*VC/NC CH 6 (7-2)
05 DF 01 1 DF ON/OFF SWITCH FF/R4/PR*50/60*VC/NC CH 2 (7-0)
06 DPH 1F 3F DF PHASE FF/R4/PR*50/60*VC/NC CH 3 (7-2)
07 QPH 19 3F QP PHASE FF/R4/PR*50/60*VC/NC CH 7 (7-2)
08 QAC 23 3F QP AMPLITUDE FF/R4/PR*50/60*VC/NC CH 8 (7-2)
09 QDC 20 3F QP DC LEVEL FF/R4/PR*50/60*VC/NC CH 12 (7-2)
0A QDV 1F 3F QP V MODULATION FF/R4/PR*50/60*VC/NC CH 5 (7-2)
0B QAV 1A 3F QP AMPLITUDE MODULATION FF/R4/PR*50/60*VC/NC CH 11 (7-2)
0C ABC 0 FF ABL D/A CONTROL ECO ON/OFF*VC/NC
WHB 00 CBO 7 0F DC OFFSET CANCELLER FOR CB1 0F (7-4)) CXA2100AQ(86H) 106
KV-ES29M90
RM-916

KV-ES29M90
RM-916
WHB 01 CRO 7 0F DC OFFSET CANCELLER FOR CR1 0F (3-0) CXA2100AQ(86H)
02 SBR 18 3F SUB BRIGHTNESS CONTROL 09 (7-2) 107
03 RDR 29 3F R DRIVE 06 (7-2) A1 (7-2)
04 GDR 25 3F G DRIVE 07 (7-2) A2 (7-2)
05 BDR 26 3F B DRIVE 08 (7-2) A3 (7-2)
06 RCT 29 3F R CUTOFF 0A (7-2) A5 (3-0)
07 GCT 12 3F G CUTOFF 0B (7-2) A6 (7-4)
08 BCT 31 3F B CUTOFF 0C (7-2) A6 (3-0)
09 SBO 29 3F SUB BRIGHTNESS OFFSET PICTURE MODE EXCEPT DYNAMIC 09 (7-2) A3 (7-2)
0A RDO 1F 3F R DRIVE OFFSET PICTURE MODE EXCEPT DYNAMIC 06 (7-2) A5 (3-0)
0B GDO 1A 3F G DRIVE OFFSET PICTURE MODE EXCEPT DYNAMIC 07 (7-2) A6 (7-4)
0C BDO 1A 3F B DRIVE OFFSET PICTURE MODE EXCEPT DYNAMIC 08 (7-2) A6 (3-0)
0D RCO 1F 3F R CUTOFF OFFSET PICTURE MODE EXCEPT DYNAMIC 0A (7-2) 106
0E GCO 1E 3F G CUTOFF OFFSET PICTURE MODE EXCEPT DYNAMIC 0B (7-2)
0F BCO 15 3F B CUTOFF OFFSET PICTURE MODE EXCEPT DYNAMIC 0C (7-2) 107
SAJ 00 PIC 3F 3F PICTURE CONTROL PICTURE MODE EXCEPT PERSONAL 01 (7-2) CXA2100AQ(86H) 105
01 BRT 1F 3F BRIGHTNESS CONTROL PICTURE MODE EXCEPT PERSONAL 04 (7-2)
02 COL 27 3F COLOR CONTROL PICTURE MODE EXCEPT PERSONAL 03 (7-2)
– 48 –
03 HUE 1F 3F HUE CONTROL PICTURE MODE EXCEPT PERSONAL 02 (7-2)

04 SHP 24 3F SHARPNESS CONTROL PICTURE MODE EXCEPT PERSONAL 05 (7-2)
05 VML 3 3 VM LEVEL PICTURE MODE 09 (1-0) 105
06 DYC 1 1 DYNAMIC COLOR ON/OFF PICTURE MODE 00 (3) 108
07 CTM 0 1 COLOR TEMPERATURE FOR DYNAMIC COLOR PICTURE MODE 00 (0) 109
08 CAX 2 3 COLOR MATRIX SPECIFICATION 50/60Hz 00 (2-1) 10A
09 GMA 3 3 GAMMA CORRECTION PICTURE MODE 04 (1-0)
0A DCT 1 3 DC TRANSMISSION CONTROL PICTURE MODE 0C (1-0)
0B DPL 1 3 AUTO PEDESTAL LEVEL CONTROL PICTURE MODE 0B (1-0)
0C ABM 0 3 ABL MODE CONTROL PICTURE MODE 08 (1-0)
0D ABT 0 3 ABL CURRENT DETECTION VTH CONTROL ECO ON/OFF*VC/NC 07 (1-0)
0E CLO 9 0F COLOR OFFSET 50/60*TV/VIDEO 03 (7-2)
0F CLW 3 7 COLOR STEP WIDTH TO THE CHANGE OF S/N 03 (7-2)
10 HUO 9 0F HUE OFFSET 50/60*TV/VIDEO 02 (7-2)
11 SHO 7 1F SHARPNESS OFFSET 50/60*TV/VIDEO/DVD 05 (7-2)
12 SHW 1 7 SHARPNESS STEP WIDTH TO THE CHANGE OF S/N 05 (7-2)
13 PIO 5 7 PICTURE OFFSET FOR TWIN/INDEX TWIN/INDEX 01 (7-2)
14 BRO 7 0F BRIGHTNESS OFFSET ECO ON/OFF*VC/NC 04 (7-2)
JGL 00 PON 1 1 RGB AND AKB REFERENCE PULSE OUTPUT ON/OFF 00 (7) CXA2100AQ(86H)
01 RGB 7 7 RGB OUTPUT SELECTION 00 (6-4)

JGL 02 AGG 0 3 AGING MODE SELECTION 0E (1-0) CXA2100AQ(86H)
03 DPS 0 1 Y/C DELAY LINE PASS MODE SWITCH 0E (3)
04 BBT 3 3 RGB BOTTOM LIMITTER CONTROL 06 (1-0)
05 LML 0 3 RGB AMPLITUDE LIMITTER CONTROL 01 (1-0)
06 PAB 0F 0F DC LEVEL FOR PEAK ABL 0E (7-4)
07 SCO 0C 0F SUB PICTURE CONTROL 0D (7-4)
08 LV2 7 0F RGB LEVEL FOR RGB2 0D (3-0)
09 SF0 1 1 SHARPNESS CIRCUIT F0 50/60*TV/VIDEO/DVD 0E (2)
0A PRO 0 3 PRE/OVER-SHOOT RATIO CONTROL 50/60*TV/VIDEO/DVD 0A (1-0)
0B LTI 2 3 LUMINANCE TRANSIENT IMPROVEMENT PICTURE MODE 05 (1-0)
0C CTI 1 3 CHROMINANCE TRANSIENT IMPROVEMENT PICTURE MODE 03 (1-0)
YCT 00 TNT 1F 3F TINT ADJUSTMENT FOR NTSC TV/VIDEO 00 (5-0) CXA2123Q(88H)
01 PNG 0 1 PAL/NTSC GATE WIDTH 00 (6)
02 PNI 0 1 PAL/NTSC SENSITIVITY SW 00 (7)
03 SCL 7 0F SUB COLOR CONTROL 50/60*TV/VIDEO 01 (3-0)
04 SCT 8 0F SUB CONTRAST CONTROL 50/60*TV/VIDEO 01 (7-4)
05 SF0 2 3 SHARPNESS CENTER FREQUENCY CHANGING 02 (1-0)
06 SEQ 3 3 SHARPNESS EQUALIZER CHARACTERISTIC 02 (3-2)
– 49 –
07 SHG 5 0F SHARPNESS GAIN CONTROL 50/60*TV/VIDEO/DVD 02 (7-4)

08 YOL 1F 3F Y-OUTPUT LEVEL CONTROL 03 (5-0)
09 BSP 0 3 BLACK STRETCH START POINT CHANGING 03 (7-6)
0A COL 1F 3F CB/CR OUTPUT LEVEL CONTROL 04 (5-0)
0B DCR 0 3 DC RESTORATION RATIO ADJUSTMENT 04 (7-6)
0C BF0 1 3 BPF/TQF F0 ADJUSTMENT 05 (1-0)
0D BFQ 2 3 BPF/TQF Q ADJUSTMENT 05 (3-2)
0E FSW 1 1 BPF/TQF SWITCH 05 (4)
0F SDT 1 1 SECAM DOUBLE TRAP SWITCH 05 (6)
10 LPF 1 1 Y/CB/CR LPF SWITCH 05 (7)
11 YDL 6 0F Y-DL TIME ADJUSTMENT 2DCOMB/3DCOMB/S-INPUT/OTHERS 06 (6-3)
12 CMT 0 1 CB/CR OUTPUT MUTE SWITCH 07 (7)
13 BO1 7 0F CB OFFSET1 ADJUSTMENT (MAIN ROUTE) 08 (7-4)
14 RO1 7 0F CR OFFSET1 ADJUSTMENT 08 (3-0)
15 CDF 0 7 V COUNT DOWN FREQUENCY SWITCH FORCED 50HZ FOR NO SIGNAL 0A (2-0)
16 CDM 0 3 V COUNT DOWN JUDGE SWITCH 0A (4-3)
17 AFC 0 3 AFC SENSITIVITY SWITCH (TV/VIDEO/DVD) 0A (6-5)
18 MVM 0 1 MACROVISION MASK + AFC MASK 0A (7)
19 SRY 7 0F SECAM R-Y BLACK ADJUSTMENT 0B (3-0)
1A SBY 1 0F SECAM B-Y BLACK ADJUSTMENT 0B (7-4)
1B BEL 2 3 SECAM BELL/HPF SWITCHING 0C (1-0)
KV-ES29M90
1C BLF 0 1 BELL F0 ADJUSTMENT 0C (2)
1D SVI 0 1 SECAM V-ID SWITCH 0C (3)
1E SGP 0 3 SECAM GATE POSITION ADJUSTMENT 0C (5-4)
RM-916

KV-ES29M90
RM-916
YCT 1F SID 1 1 SECAM SENSITIVITY SWITCH EXCEPT SECAM 0C (6) CXA2123Q(88H)
20 SIH 0 1 SECAM INHIBITION SWITCH 0C (7)
21 STP 0 1 Y BLACK LEVEL SETUP FOR PAL PLUS 0D (1)
22 HVC 2 3 H-VCO TEMPERATURE CHARACTER CANCELLING 0D (7-6)
23 3NR 1 1 3D NR OPERATION ON/OFF
24 BW6 1 1 3D NR FOR 60Hz NON-BUST SIGNAL ON/OFF
25 WSH 0 3 SHARPNESS GAIN STEP FOR NOISE REDUCTION 02 (7-4)
26 WCO 0 3 CB/CR OUTPUT LEVEL STEP FOR NOISE REDUCTION 04 (5-0)
SYC 00 TNT 1F 3F TINT ADJUSTMENT FOR NTSC TV/VIDEO 00 (5-0) CXA2123Q(8AH)
01 PNG 0 1 PAL/NTSC GATE WIDTH 00 (6)
02 PNI 0 1 PAL/NTSC SENSITIVITY SW 00 (7)
03 SCL 7 0F SUB COLOR CONTROL 50/60*TV/VIDEO/DVD 01 (3-0)
04 SCT 7 0F SUB CONTRAST CONTROL 50/60*TV/VIDEO/DVD 01 (7-4)
05 SF0 2 3 SHARPNESS CENTER FREQUENCY CHANGING 02 (1-0)
06 SEQ 3 3 SHARPNESS EQUALIZER CHARACTERISTIC 02 (3-2)
07 SHG 7 0F SHARPNESS GAIN CONTROL 02 (7-4)
08 YOL 1F 3F Y-OUTPUT LEVEL CONTROL 03 (5-0)
09 BSP 0 3 BLACK STRETCH START POINT CHANGING 03 (7-6)
– 50 –
0A COL 1F 3F CB/CR OUTPUT LEVEL CONTROL 04 (5-0)

0B DCR 0 3 DC RESTORATION RATIO ADJUSTMENT 04 (7-6)
0C BF0 1 3 BPF/TQF F0 ADJUSTMENT 05 (1-0)
0D BFQ 2 3 BPF/TQF Q ADJUSTMENT 05 (3-2)
0E FSW 1 1 BPF/TQF SWITCH 05 (4)
0F SDT 1 1 SECAM DOUBLE TRAP SWITCH 05 (6)
10 LPF 1 1 Y/CB/CR LPF SWITCH 05 (7)
11 YDL 3 0F Y-DL TIME ADJUSTMENT PAL/NTSC/SECAM/S-INPUT 06 (6-3)
12 NCM 1 1 1-H ADDITION SWITCH 06 (7)
13 CMT 0 1 CB/CR OUTPUT MUTE SWITCH 07 (7)
14 BO1 7 0F CB OFFSET1 ADJUSTMENT (MAIN ROUTE) 08 (7-4)
15 RO1 7 0F CR OFFSET1 ADJUSTMENT 08 (3-0)
16 CDF 0 7 V COUNT DOWN FREQUENCY SWITCH 0A (2-0)
17 CDM 0 3 V COUNT DOWN JUDGE SWITCH 0A (4-3)
18 AFC 0 3 AFC SENSITIVITY SWITCH (TV/VIDEO/DVD) 0A (6-5)
19 MVM 0 1 MACROVISION MASK + AFC MASK 0A (7)
1A SRY 7 0F SECAM R-Y BLACK ADJUSTMENT 0B (3-0)
1B SBY 1 0F SECAM B-Y BLACK ADJUSTMENT 0B (7-4)
1C BEL 2 3 SECAM BELL/HPF SWITCHING 0C (1-0)
1D BLF 0 1 BELL F0 ADJUSTMENT 0C (2)
1E SVI 0 1 SECAM V-ID SWITCH 0C (3)

SYC 1F SGP 0 3 SECAM GATE POSITION ADJUSTMENT 0C (5-4) CXA2123Q(8AH)
20 SID 1 1 SECAM SENSITIVITY SWITCH EXCEPT SECAM 0C (6)
21 SIH 0 1 SECAM INHIBITION SWITCH 0C (7)
22 STP 0 1 Y BLACK LEVEL SETUP FOR PAL PLUS 0D (1)
23 HVC 2 3 H-VCO TEMPERATURE CHARACTER CANCELLING 0D (7-6)
AP 00 BAS 0A 0F BASS CONTROL SOUND MODE EXCEPT PERSONAL #4 (3-0) TDA7315(80H) 358 (1-0)
01 TRE 0A 0F TREBLE CONTROL SOUND MODE EXCEPT PERSONAL #5 (3-0) 359 (1-0)
02 LDN 1 1 LOUDNESS ON/OFF #3 (2)
MSP 00 WST 15 FF W/G STEREO THRESHOLD MSP3415D(84H) 165
01 WBT EA FF W/G BILINGUAL THRESHOLD 166
02 WLL 5 FF W/G MONAURAL THRESHOLD 167
03 WAC 1 0F W/G AGREEMENT COUNT 168
04 WDL 30 FF W/G SEARCH DELAY 169
05 NDL 20 FF NICAM SEARCH DELAY 16A
06 SDL 10 FF STEREO STATUS READ DELAY 16B
07 AGC 1 1 AGC SWITCH AUTO/CONSTANT 00BB (7) 116 (7)
08 REL 28 3F AGC GAIN AT CONSTANT MODE 00BB (6-1) 116 (6-1)
– 51 –
09 CRM 0 1 CARRIER MUTING ON/OFF 00BB (9) 115 (1)

0A ACO 1 1 AUDIO CLOCK ON/OFF 0083 (5) 11A (5)
0B FP 1B 7F FM PRESCALE FOR NON-M SYSTEM 000E (7-0) 329
0C FPM 32 7F FM PRESCALE FOR M SYSTEM 000E (7-0) 32A
0D FH 2D 7F FM PRESCALE FOR HDEV 000E (7-0) 32B
0E FHM 65 7F FM PRESCALE FOR HDEV AND M 000E (7-0) 32C
0F WGP 2A 7F W/G PRESCALE 000E (7-0) 32D
10 NIP 6D 7F NICAM PRESCALE 0010 (7-0) 32E
11 ERR 50 FF AUTO FM SWITCH THRESHOLD 0021 (10-3) 14F
12 VOL 6D FF LOUDSPEAKER GAIN 0700H TO 07FFH 0000 (11-4) 368
LTI 00 LDH 1 1 HISTOGRAM SEGMENT SELECTION 00 (2) TDA9178(40H) 175 (2)
01 CFS 1 1 CONTOUR FILTER SELECTION 00 (3) 175 (3)
02 WLB 0 1 LETTERBOX WINDOW SWITCH 00 (5) 175 (5)
03 VDC 1 1 VIDEO DEPENDENT CORING PICTURE MODE 00 (6) 175 (6)
04 DEM 0 1 DEMONSTRATION MODE 00 (7) 175 (7)
05 CDP 4 07 LUMINANCE DELAY 01 (2-0) 176 (2-0)
06 OSP 0 1 OVERRULE SMART PEAKING 01 (5) 176 (5)
07 WPO 0 1 WHITE POINT STRETCH OFF 01 (4) 176 (4)
08 DSK 0 1 SKIN TONE SWITCH PICTURE MODE 02 (0) 177 (0)
09 ASK 0 1 SKIN TONE ANGLE SELECTION 02 (1) 177 (1)
0A WSK 0 1 SKIN TONE WIDTH SELECTION 02 (2) 177 (2)
KV-ES29M90
0B SSK 0 1 SKIN TONE SIZE SELECTION 02 (3) 177 (3)
0C DGR 1 1 GREEN ENHANCEMENT SWICTH PICTURE MODE & TWIN 02 (4) A9 (4)
0D DGT 7 7 THRESHOLD OF GREEN ENHANCEMENT SWITCH A9 (7-5)
RM-916

KV-ES29M90
RM-916
LTI 0E GGR 0 1 GREEN ENHANCEMENT GAIN 02 (5) TDA9178(40H) 177 (5)
0F WGR 0 1 GREEN ENHANCEMENT WIDTH 02 (6) 177 (6)
10 SGR 0 1 GREEN ENHANCEMENT SIZE 02 (7) 177 (7)
11 DBL 0 1 BLUE STRETCH SWITCH 03 (0) 178 (0)
12 GBL 0 1 BLUE STRETCH GAIN SELECTION 03 (1) 178 (1)
13 SBL 0 1 BLUE STRETCH SIZE SELECTION 03 (2) 178 (2)
14 CDS 1 1 COLOR DEPENDENT SHARPNESS PICTURE MODE 03 (3) A9 (3)
15 CST 7 7 THRESHOLD OF COLOR DEPENDENT SHARPNESS A9 (2-0)
16 CTI 0 1 COLOR TRANSIENT IMPROVEMENT PICTURE MODE 03 (4) 178 (4)
17 BON 0 1 BLACK OFFSET COMPENSATION PICTURE MODE 03 (5) 178 (5)
18 BTD 0 3F ADAPTIVE BLACK STRETCH PICTURE MODE 04 (5-0) 179 (5-0)
19 NLD 15 3F NON-LINEARITY AMPLIFIER PICTURE MODE & TWIN 05 (5-0) AA (5-0)
1A NLW 7 7 STEP WIDTH OF NON-LINEARITY AMPLIFIER 05 (5-0) AE (6-4)
1B VGD 15 3F VARIABLE GAMMA PICTURE MODE & TWIN 06 (5-0) AB (5-0)
1C VGW 0 7 STEP WIDTH OF VARIABLE GAMMA 06 (5-0) AE (2-0)
1D PKD 3F 3F PEAKING AMPLITUDE PICTURE MODE 07 (5-0) AC (5-0)
1E PKW 8 0F STEP WIDTH OF PEAKING AMPLITUDE 07 (5-0) AF (7-4)
1F SPD 0 3F STEEPNESS CORRECTION PICTURE MODE 08 (5-0) 17D (5-0)
– 52 –
20 CRD 11 3F CORING LEVEL PICTURE MODE 09 (5-0) AD (5-0)

21 CRW 9 0F STEP WIDTH OF CORING LEVEL 09 (5-0) AF (3-0)
22 CRO 0 0F CORING LEVEL OFFSET FOR VIDEO MODE 09 (5-0) AF (3-0)
23 LWD 1F 3F LINE WIDTH CORRECTION 0A (5-0) 17F (5-0)
24 SNM 0 7 S/N MODE UNDER UNREALIBLE S/N CONDITION B0 (2-0)
25 SNC 3 0F S/N RATIO AVERAGE COUNTER TV/VIDEO B1 (3-0)
26 FMC 2 0F FEATURE MODE MATCHING COUNTER B2 (3-0)
MID 00 HPH FF HORIZONTAL ACTIVE DISPLAY AREA PHASE MB94918(68H)
01 VPH 3F VERTICAL ACTIVE DISPLAY AREA PHASE
02 HSZ FF HORIZONTAL ACTIVE DISPLAY AREA SIZE
03 VSZ FF VERTICAL ACTIVE DISPLAY AREA SIZE
04 HPW 3F DISPLAY H-SYNC PLUSE WIDTH
05 VPW 7 DISPLAY V-SYNC PLUSE WIDTH
06 YDL 3F DISPLAY OUTPUT Y/C DELAY CORRECTION
07 MHP FF MAIN PICTURE HORIZONTAL POSITION (SINGLE & PINP)
08 MVP FF MAIN PICTURE VERTICAL POSITION (SINGLE & PINP)
09 MHS FF MAIN PICTURE HORIZONTAL SIZE (SINGLE & PINP)
0A MVS FF MAIN PICTURE VERTICAL SIZE (SINGLE & PINP)
0B PHP FF PINP SUB PICTURE HORIZONTAL POSITION
0C PVP FF PINP SUB PICTURE VERTICAL POSITION
0D PHS FF PINP SUB PICTURE HORIZONTAL SIZE
0E PVS FF PINP SUB PICTURE VERTICAL SIZE
0F PHO FF PINP SUB PICTURE HORIZONTAL POSITION OFFSET
10 PVO FF PINP SUB PICTURE VERTICAL POSITION OFFSET

MID 11 TMP FF TWIN MAIN PICTURE HORIZONTAL POSITION MB94918(68H)
12 TSP FF TWIN SUB PICTURE HORIZONTAL POSITION
13 TVP FF TWIN MAIN & SUB PICTURE VERTICAL POSITON
14 THS FF TWIN MAIN & SUB PICTURE HORIZONTAL SIZE
15 TVS FF TWIN MAIN & SUB PICTURE VERTICAL SIZE
16 THO FF TWIN MAIN & SUB PICTURE HORIZONTAL POSITION OFFSET
17 TVO FF TWIN MAIN & SUB PICTURE VERTICAL POSITION OFFSET
18 XHS FF INDEX SUB PICTURE HORIZONTAL SIZE
19 XVS FF INDEX SUB PICTURE VERTICAL SIZE
1A XHG FF INDEX HORIZONTAL GAP WIDTH BETWEEN PICTURES
1B XVG FF INDEX VERTICAL GAP WIDTH BETWEEN PICTURES
1C XHP FF INDEX 1ST SUB PICTURES HORIZONTAL POSITION
1D XVP FF INDEX 1ST SUB PICTURES VERTICAL POSITION
1E DHP FF DRC HORIZONTAL ACTIVE AREA POSITION
1F DHS FF DRC HORIZONTAL ACTIVE PIXEL SIZE
20 DVP 3F DRC VERTICAL ACTIVE AREA LINE POSITION
21 DVS FF DRC VERTICAL ACTIVE AREA LINE SIZE
22 VHP FF VDO HORIZONTAL ACTIVE AREA POSITION
– 53 –
23 VHS FF VDO HORIZONTAL ACTIVE AREA PIXEL SIZE

24 VEP 3F VDO VERTICAL ACTIVE AREA EVEN POSITION
25 VVS FF VDO VERTICAL ACTIVE AREA LINE SIZE
26 VOP 3 VDO VERTICAL ACTIVE AREA ODD POSITION
27 CLT FF VDO CLAMP PULSE OUTPUT TIMING
28 CLW 7 VDO CLAMP PULSE WIDTH
29 VYD 3F VDO ANALOG INPUT Y/C DELAY CORRECTION
2A VCR 1 VDO CROMA SIGNAL ORDER
2B VDI 3 VDO DIGITAL ANALOG INPUT SELECTION
3CM 00 FRZ 0 1 EXTERNAL MEMORY TEST BIT 02 (4) UPD64082(B8H)
01 NRM 0 3 NOISE REDUCTION OPERATION MODE 00 (7-6)
02 YCO 0E 0F Y/C SIGNAL OUTPUT SELECTION 00 (3-0)
03 SYC 1 3 SYSTEM CLOCK SELECTION 01 (7-6)
04 STD 0 3 STANDARD/NON-STANDARD OPERATION SELECTION 01 (5-4)
05 MSS 0 3 INTER-FRAME/INTER-LINE OPERATION SELECTION 01 (3-2)
06 KIL 3 3 KILLER/NON-KILLER OPERATION SELECTION 01 (1-0)
07 EAD 0 1 EXTERNAL Y-ADC SWITCH 02 (5)
08 ECS 1 3 EXTERNAL C-SYNC INPUT SELECTION 02 (1-0)
09 CPP 2 3 ADC INPUT LEVEL & CLUMP PULSE WIDTH SELECTION 03 (7-6)
0A PWR 0 1 ADC INPUT WIDTH SWITCH 09 (7)
0B HDP 5 7 HORIZONTAL PHASE ADJUSTMENT 03 (5-3)
KV-ES29M90
0C CDL 4 7 C-SIGNAL DELAY ADJUSTMENT 03 (2-0)
0D DYC 2 0F DY DETECTION CORING LEVEL ADJUSTMENT NR MODE (0-3) 04 (7-4)
0E DYG 0A 0F DY DETECTION GAIN ADJUSTMENT NR MODE (0-3) 04 (3-0)
RM-916

KV-ES29M90
RM-916
3CM 0F DCC 5 0F DC DETECTION CORING LEVEL ADJUSTMENT NR MODE (0-3) 05 (7-4) UPD64082(B8H)
10 DCG 5 0F DC DETECTION GAIN ADJUSTMENT NR MODE (0-3) 05 (3-0)
11 YNR 1 0F YNR NON-LINEAR FILTER SETUP 06 (7-4)
12 CNR 1 0F CNR NON-LINEAR FILTER SETUP 06 (3-0)
13 WSC 1 3 NOISE DETECTION CORING ADJUSTMENT 08 (7-6)
14 VTH 1 3 HYSTERESIS SELECTION FOR H-SYNC NON-STANDARD TV/VIDEO 08 (5-4)
15 VTR 1 3 SENSITIVITY SELECTION FOR H-SYNC NON-STANDARD TV/VIDEO 08 (3-2)
16 LDR 2 3 SENSITIVITY SELECTION FOR FRAME-SYNC NON-STANDARD TV/VIDEO 08 (1-0)
17 VAP 3 7 GAIN ADJUSTMENT FOR VERTICAL SHAPE CORRECTION PICTURE MODE 0A (7-5)
18 VAI 0C 1F VANISHING ADJUSTMENT FOR VERTICAL SHAPE CORRECTION PICTURE MODE 0A (4-0)
19 TST 0 1 TEST BIT 0B (6)
1A YPF 3 3 CENTER FREQUENCY SELECTION FOR Y-PEAKING BPF PICTURE MODE 0B (5-4)
1B YPG 8 0F GAIN ADJUSTMENT FOR Y-PEAKING BPF PICTURE MODE 0B (3-0)
1C VSE 0A 0F LINE COMB FILTER SETUP 0C (7-4)
1D CCN 0 1 C-SIGNAL SPLIT FILTER SWITCH 0C (3)
1E COS 0 1 C-SIGNAL DELAY SWITCH AT NOISE REDUCTION 0C (2)
1F SDC 0 1 DC DETECTION SENSITIVITY SWITCH 0C (0)
20 SDY 1 1 DY DETECTION LOWER-LEVEL SENSITIVITY SWITCH 0D (5)
– 54 –
21 D2G 4 7 D2 GAIN SELECTION 0D (2-0)

22 YHC 0 3 Y-SIGNAL HIGHER-LEVEL CORING SELECTION PICTURE MODE 10 (7-6)
23 YHG 0 1 Y-SIGNAL HIGHER-LEVEL GAIN SWITCH PICTURE MODE 10 (5)
24 SHT 0 0F NON-STANDARD DETECTION & H/V COUNTER TEST BITS 11 (7-4)
25 CLK 8 0F CLOCK TEST BITS 11 (3-0)
26 PLL 0D 0F PLL FILTER SETUP 12 (7-4)
27 KRF 3 0F KILLER DETECTION REFERENCE ADJUSTMENT 12 (3-0)
28 HSL 0C 0F H-SYNC SLICE LEVEL ADJUSTMENT 13 (7-4)
29 VSL 8 0F V-SYNC SLICE LEVEL ADJUSTMENT 13 (3-0)
2A BPS 4 0F INTERNAL BURST GATE START POSITION ADJUSTMENT 14 (7-4)
2B BPW 0A 0F INTERNAL BURST GATE WIDTH ADJUSTMENT 14 (3-0)
2C ADC 3 3 ADC CLOCK DELAY SELECTION 15 (7-6)
2D APD 1 1 ADC POWER-DOWN SWITCH 15 (5)
2E NSD 1 1 NON-STANDARD DETECTION TEST BIT 15 (4) 322
2F SPD 2 3 MEMORY POWER-DOWN SWITCH 16 (7) 323
30 CNT 0 1 CNR TEST BIT 17 (7) 324
2CM 00 APA 1 1 2D COMB APACON ON/OFF PICTURE MODE #2 (2-1) CXA2069Q(90H)
DSP 00 DUL 0 3 DIR UNLOCK DETECTION MODE TC9446F(3AH)
01 DIM 3 3 DIGITAL INPUT MODE
02 TFM 5A 7F TRUSURROUND FRONT MINUS VDD/VDP 2764/276D
03 TFP 12 7F TRUSURROUND FRONT PLUS VDD/VDP 2765/276E
04 TCE 40 7F TRUSURROUND CENTER VDD/VDP 2766/276F
05 TS1 20 FF TRUSURROUND SURROUND #1 VDD/VDP 2767
06 TS2 20 7F TRUSURROUND SURROUND #2 VDD/VDP 2770

DSP 07 TSP 68 7F TRUSURROUND SURROUND PLUS VDD/VDP 2768/2771 TC9446F(3AH)
08 TEM 68 7F TRUSURROUND SURROUND MINUS VDD/VDP 2769/2772
09 LFE 5A 7F LOW FREQUENCY EFFECT 276A/2773 31E
0A BHL 40 7F BBE EFFECT 1 FOR BBE HIGH VDD/VDP/TRS/SIM/OFF 278F 321
0B BHH 48 7F BBE EFFECT 2 FOR BBE HIGH VDD/VDP/TRS/SIM/OFF 2790 322
0C BLL 33 7F BBE EFFECT 1 FOR BBE LOW VDD/VDP/TRS/SIM/OFF 278F 323
0D BLH 33 7F BBE EFFECT 2 FOR BBE LOW VDD/VDP/TRS/SIM/OFF 2790 324
0E DLR 7 7 DELAY SELECTION AT DSP RESET 324
0F BBE 1 3 BBE SELECTION SOUND MODE EXCEPT PERSONAL 324
DYC 00 SBH 1F 3F H STATIC CONV1 50/60Hz 0D (5-0) CXA8070P(DEH)
01 YBU 1F 3F H STATIC CONV2 UPPER 50/60Hz 0B (5-0)
02 YBL 1F 3F H STATIC CONV2 LOWER 50/60Hz 0C (5-0)
03 RSA 1F 3F H DYNAMIC CONV1 LEFT 50/60Hz 05 (5-0)
04 LSA 1F 3F H DYNAMIC CONV1 RIGHT 50/60Hz 0A (5-0)
05 LUB 1F 3F H DYNAMIC CONV2 TOP LEFT 50/60Hz 01 (5-0)
06 LLB 1F 3F H DYNAMIC CONV2 BOTTOM LEFT 50/60Hz 02 (5-0)
07 RUB 1F 3F H DYNAMIC CONV2 TOP RIGHT 50/60Hz 06 (5-0)
08 RLB 1F 3F H DYNAMIC CONV2 BOTTOM RIGHT 50/60Hz 07 (5-0)
– 55 –
TXT 00 TXH 4B FF TELETEXT HORIZONTAL POSITION 99 (7-0) SAA5261(58H) 352 (1-0)

01 TXV 0E 3F TELETEXT VERTICAL POSITION 9A (5-0) 352 (5-4)
OPM 00 OSH 12 3F OSD H POSITION 1F1 CXP750096(60H) 18D (7-2)
01 FW1 0 3F OSD ODD/EVEN FIELD WINDOW SETUP #1 1F9 OPTION-MISC
02 FW2 3 3F OSD ODD/EVEN FIELD WINDOW SETUP #2 1F9
03 OHO 9 0F OSD H POSITION OFFSET FOR INDEX 1F1
04 ICO 1 3 INDEX “VIDEO” OSD HORIZONTAL OFFSET (12+1 INDEX)
05 ISO 2 3 INDEX SUB-SCREEN OSD HORIZONTAL OFFSET
06 IL1 1C 3F INDEX SUB-SCREEN OSD 1ST LINE VERTICAL POSITION 50/60Hz 1F2
07 IVO 2F 3F INDEX SUB-SCREEN OSD VERTICAL OFFSET 50/60Hz 1F2/1F3
08 COM 0 03 COMB OPERATION SELECTION 347 (7-6)
09 APC 1 1 APC SWITCH 346 (5)
0A TSY 0 03 TV SYSTEM SELECTION UNDER SEARCHING WITH AUTO TV SYSTEM 346 (4-3)
0B MUT 0 1 NO SIGNAL MUTE 346 (0)
0C AFM 1 1 AUTO FM SWITCH 346 (1)
0D TVO 3 7 V-ANGLE CORRECTION TO PICTURE ROTATION 347 (2-0)
0E DBL 0 1 DISABLE BLUEBACK FUNCTION 346 (2)
0F SSO 1 3 SPEED CH SEARCH SELECTION 346 (5)
10 TRP 0 3F MPEG/JPEG NOISE REDUCTION FOR EACH INPUT 18E (5-0)
00 SCH 1 7F CH SELECTION FOR SHIPPING CONDITION NTSC ONLY
KV-ES29M90
10 SCA 1 1 CABLE/AIR SELECTION FOR SHIPPING CONDITION NTSC ONLY 18E (5-0)
OPB 00 OP1 E7 FF OPTIONAL BITS 1 (SEE THE SPECIFIED SHEET) OPTION-BITS 4A
01 OP2 13 FF OPTIONAL BITS 2 (SEE THE SPECIFIED SHEET) 4B
RM-916

KV-ES29M90
RM-916
NOTE
• shaded items are fixed data.
• Standard data listed on the Adjustment Item Table are reference values, therefore it may be different for each model and for each mode.
• Note for Different Data: Those are the standard data values written on the microprocessor. Therefore, the data values of the modes
and stored respectively in the memory.
In case of a device replacement, adjustment by rewriting the data value is necessary for some items.
OPTION NOTE
COM Comb Operation Selection 00 = automatic operation (depends on color system status),
01 = no comb operation,
02 = forced 2D-comb operation,
03 = forced 3D-comb operation
TSY TV System Selection for Auto TV System 00 = B/G, 01 = I, 10 = D/K, 11 = M
SSO Speed CH Search Selection 00 = normal, 01 = 4 times, 10 = 6 times, 11 = 8 times
TRP MPEG/JPEG Noise Reduction

Input – – TV Video 1 Video 2 Video 3 Video 4 DVD
OP1 Items
Item TOP NICAM HDEV Reserved – DVD Input AV Input
KV-ES29M90 1 1 1 0 0 1 1 1
AV Input 00 = no AV Input, 01 = 1 AV Input, 10 = 3 AV Input, 11 = 4 AV Input
OP2 Items
Item C-Text Korean Stereo Korean Mode A-TVsys US ST SSV Model OSD Language
KV-ES29M90 0 0 0 1 0 0 1 1
– 56 –

KV-ES29M90
RM-916
5-3. PICTURE QUALITY ADJUSTMENTS 1. NTSC VIDEO INPUT

SUB COLOR ADJUSTMENT (SCL) Input signal ; NTSC color bar, 75% to Video 1.
1. Set to service mode. [TWIN] mode, [Service] mode.
2. Input RF PAL colorbar signal.
Set A/V control to PERSONAL. (i) SUB CONTRAST
3. Set to VP7 (Service mode) "DYC" = 0 Condition : SAJ 00 PIC 3F
4. Set the following condition. 02 COL 0
Picture to 100%, Color to 0% and Bright to 0%. JGL 01 RGB 4
5. Connect an oscilloscope to the pin 3 (BLUE) of CN705, C SAJ 13 PIO 0
board. Adjusting parameter:
6. Using the 1 and 4 buttons select SAJ 3 (Service mode) LEFT ; YCT 08 YOL
"SCL". RIGHT ; SYC 08 YOL
7. Using the 3 and 6 buttons on the Remote Commander to
adjust to VB2 = VB3 = VB4 with 3 and 6.
8. Write into the memory by pressing "MUTING" then "0".
VR
9. Input NTSC colorbar signal to VIDEO1 and select VIDEO1
input. VR2
10. Adjust as step 4. and 8. by receving NTSC colorbar.
GND
11. Reset to VP 7 (Service mode) "DYC" = 1.
VR1 - VR2 = VR = 1.88 ± 0.07 (Vp-p)
-H-TRAPIZIUM ADJUSTMENT
(ii) SUB HUE/SUB COL
1. Input a cross hatch/dot signal.
Condition : SAJ 02 COL 1F
2. Adjust DAC 4 HTR to make H-Trapizoid distortion best.
JGL 01 RGB 7
SAJ 10 HUO 7
SUB CONTRAST, SUB HUE, SUB COLOR
Adjusting parameter:
Adjustment condition LEFT ; YCT 0A COL
SAJ 00 PIC 3F YCT 00 TNT
00 DYC 0 RIGHT ; SYC 0A COL
0E CLO 7 SYC 00 TNT
10 HUO 7
13 PIO 0
VB4
JGL 04 BBT 0
05 LML 3
VB1 VB2 VB3
PICTURE QUALITY : HI-FINE
ECO MODE : OFF VB1 = VB4 ± 50 mV
WIDE MODE : OFF VB2 = VB3 ± 50 mV
DRC-MF : DRC1250
INPUT SIGNAL
Video Color Bar (White and Color 75%)
RF Color Bar (White and Color 75%)
CAUTION
After the above Adjustments, these adjustment parameters must be
recovered to the original condition.
VR ; R100 (the pin 6 of CN1100)

VB ; B100 (the pin 7 of CN1100)
– 57 –

KV-ES29M90
RM-916
2. NTSC RF INPUT 3. PAL VIDEO INPUT

Input signal ; NTSC RF color bar, 75%. Input signal ; PAL color bar, 75% to Video 1.
[TWIN] mode, [Service] mode. [TWIN] mode, [Service] mode.
(i) SUB CONTRAST (i) SUB CONTRAST

Condition : SAJ 00 PIC 3F Condition : SAT 00 PIC 3F
02 COL 0 SAT 02 COL 0
JGL 01 RGB 4 JGL 01 RGB 4
Adjusting parameter: Adjusting parameter:
LEFT ; YCT 04 SCT LEFT ; YCT 04 SCT
RIGHT ; SYC 04 SCT RIGHT ; SYC 04 SCT
VR VR
VR2 VR2
GND GND
VR1 - VR2 = VR = 1.88 ± 0.07 (Vp-p) VR1 - VR2 = VR = 1.88 ± 0.07 (Vp-p)
(ii) SUB HUE/SUB COL (ii) SUB HUE/SUB COL

Condition : SAJ 02 COL 1F Condition : SAJ 02 COL 1F
JGL 01 RGB 7 JGL 01 RGB 7
SAJ 10 HUO 7 Adjusting parameter:
Adjusting parameter: LEFT ; YCT 03 SCL
LEFT ; YCT 03 SCL SAJ 10 HUO
YCT 00 TNT RIGHT ; SYC 03 SCL
RIGHT ; SYC 03 SCL
SYC 00 TNT
VB4
VB4
VB1 VB2 VB3
VB1 VB2 VB3 VB1 = VB4 ± 50 mV

VB2 = VB3 ± 50 mV
VB1 = VB4 ± 50 mV
VB2 = VB3 ± 50 mV
– 58 –

KV-ES29M90
RM-916
3. PAL RF INPUT 5-4. DEFLECTION ADJUSTMENTS

Input signal ; PAL RF color bar, 75%.
FOR DRC 1250
[TWIN] mode, [Service] mode.
1. Set to Service Mode.
2. Input a Pal cross hatch/dot signal.
(i) SUB CONTRAST
3. Set the following condition.
Condition : SAJ 00 PIC 3F
Picture Mode to [DYNAMIC], Picture Rotation to [+/– 0] and
SAJ 02 COL 0
Eco Mode to OFF.
JGL 01 RGB 4
4. Set to DRC 1250 mode.
5. Using the 1 and 4 buttons select category GEO (Service
LEFT ; YCT 04 SCT
Mode).
RIGHT ; SYC 04 SCT
6. Select and adjust the following items to obtain optimum image.
Raise/lower the data with the 3 and 6 buttons.
VR 1 00 VSZ V SIZE
2 04 HSZ H SIZE
VR2
3 01 VPS V POSITION
GND 4 05 HPS H POSITION
5 03 SCO S CORRECTION
VR1 - VR2 = VR = 1.88 ± 0.07 (Vp-p)
6 02 VLN V LINEARITY
7 0B BOW AFC BOW
(ii) SUB HUE/SUB COL
8 06 PAP PIN AMP
Condition : SAJ 02 COL 1F
9 07 UPN UPPER CORNER PIN
JGL 01 RGB 7
10 08 LPN LOWER CORNER PIN
11 09 TRZ TRAPEZIUM
LEFT ; YCT 03 SCL
SAJ 10 HUO
7. Using the 1 and 4 buttons select category DAC (Service
RIGHT ; SYC 03 SCL
Mode).
8. Select and ad List the following items to obtain optimum image.
VB4
1 01 HLN H LINEARITY
2 00 HCT H CENTER
VB1 VB2 VB3
9. Select “GEO 04 HSZ” with the 1 and 4 buttons.

VB1 = VB4 ± 50 mV 10. Confirm the H Size condition. If necessary, adjust the H SIZE
VB2 = VB3 ± 50 mV
to get a best condition.
– 59 –

KV-ES29M90
RM-916
11. Write into the memory by pressing [MUTING] then -. 5-5. A BOARD ADJUSTMENT AFTER IC003
FOR DRC 100 MODE (MEMORY) REPLACEMENT
12. Set to DRC 100 mode.
13. Repeat Step 5, Step 6 and Step 7.
When replacing IC003 and IC004 (MEMORY), be sure to change
14. Write “DAC 00 HCT DRC 100 Mode” as “DAC 00 HCT DRC
IC001 (µ-COM) to the following new IC at the same time.
1250 Mode”.
Write “DAC 01 HLN DRC 100 Mode” as “DAC 01 HLN DRC
MODEL IC001 (µ-CON)
1250 Mode”.
KV-ES29M90 CXP750096-012Q
FOR PIP MODE

1. Enter to Service Mode.
15. Set to PIP mode.
16. Repeat Step 5 and Step 6.
2. Press commander buttons 5 and - (Data Initialize), and 2
17. Write into the memory by pressing [MUTING] then -.
and - (Data Copy) to initialize the data.
FOR TWIN MODE

18. Set to TWIN Mode. 3. Call each item number and check if the respective screen shows
19. Using the 1 and 4 buttons select category GEO (Service the normal picture.
Mode). In cases where items are not well adjusted, rectify the items
20. Select and adjust the following items to obtain optimum image. with fine adjustment.
Raise/lower the data with the 3 and 6 buttons. Write the data per each item number ([MUTING] +-).
1 01 VPS V POSITION 4. Select item numbers “OPB0” (OP1), “OPB1” (OP2) and
2 05 HPS H POSITION respectively set the bit per model with command buttons 3
3 06 PAP PIN AMP and 6.
4 09 TRZ TRAPEZIUM
5. Press commander buttons 8 and - (Test Normal) to return
21. Write into the memory by pressing [MUTING] then -. to the data that was set on the shipment from the factory.
(This will also cancel Service Mode.)
FOR INDEX M0DE
22. Set to Index Mode.
23. Repeat Step 5 and Step 6.
24. Write into the memory by pressing [MUTING] then -.
FOR WIDE MODE

25. Set to WIDE Mode.
26. Using the 1 and 4 buttons select category GEO (Service
Mode).
27. Select and adjust the following items to obtain optimum image.
1 00 VSZ V SIZE
2 01 VPS V POSITION
3 05 HPS H POSITION
4 06 PAP PIN AMP
5 09 TRZ TRAPEZIUM
28. Input a NTSC cross hatch/dot signal and repeat all above steps.
– 60 –

KV-ES29M90
RM-916
5-6. PICTURE DISTORTION ADJUSTMENT (1) PICTURE DISTORTION ADJUSTMENT (2)

Item Number 00 – 0B H-TRAPEZOID (DAC 4 HTR)
GEO 0 VSZ (V SIZE)
GEO 1 VPS (V POSITION)
GEO 2 VLN (V LINEARITY)
GEO 3 SCO (VERTICAL S-Correction)
GEO 4 HSZ (H SIZE)
GEO 5 HPS (H POSITION)
GEO 6 PAP (PIN AMP)
GEO 07 UPN (UPPER CORNER PIN)

GEO 08 LPN (LOWER CORNER PIN)
GEO 9 TRZ (TRAPEZIUM)
GEO 0A AGL (AFC.ANGLE)
GEO 0B BOW (AFC.BOW)
– 61 –

KV-ES29M90
RM-916
MEMO
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
– 62 –

KV-ES29M90 KV-ES29M90 KV-ES29M90 KV-ES29M90
SECTION 6 RM-916 RM-916 RM-916 RM-916
DIAGRAMS
6-1. BLOCK DIAGRAM
T6602
MAIN
CONVERTER
7 2
18 VPROT V PROT
CN6801
9 1 Q6811, Q6819
Q6820, Q6821
C (CRT DRIVE)
V.DY
6 ±17V RECT +17V AUDIO D6801

18 D6634 –17V AUDIO V+ 6
1 PUMP UP
19 VSAW– Q6801
V- 5
17 VSAW+ 3 5
H.DY V.DY
3 4
10 HD2 7
H-OUT DRIVE HDT PIN OUT
+12V REG Q6806 T6804 Q6808 H- 3
CN1652 +15V
17 I O +12V IC6800
1 MAIN RECT V-OUT 2
FROM D6605 G 13 HD1
TO D1 BOARD CN6802
H-OUT DRIVE HDT H-OUT

F2 5 AC IN RY6601 Q6805 T6802 Q6807 H+ 1
7 H. PULSE IC9001
H.DY
16
TH6601 IC6801 DY-PROT
CN6603
3
RELAY
RY6603 +6.5V RECT +6.5V 5V
9 EXTRA PARA
15 FOCUS
CN6802
44 3
DY D9005 VIDEO OUT (RED) 32CI
15
2
D6633
16 VM
CN6802
H-CERT
1
PICTURETUBE
3.3V 20 N/S H-SAW
200V 1
2 VB J9001
1 RELAY DRIVE RELAY
14 46 Q6813, 14 2 TO C BOARD CN9001
RY6602 H1 4 CN9002 R
DGC CHECK
Q6601
2.5V
14 X-RAY H-SAW 5 H-CAMP Q9009
Q6804, 3 R DRIVE 1 3 VI VO 8
DGC CHECK
FOR
1
5 SWITCHING
13 BUFFER G 12
17 N/S TO PICTURE TUBE
ST-BY RECT
2 REGULATOR +10.5V RECT +10.5V 9V 1 HV

CHECK D D6644 T6800 HV
S 1 12
31 VM 9 VOF B 11
CN6602
29 FOCUS
10
DEGAUSS
11
15 EXTRA-PARA H-C SHIFT H-C OUT 9 IK
PIN
CN6800
C 4
+135V RECT 13 AFC PULSE
Q6822 Q6802
4 5 HV
T6601 +135V
D6631
D BOARD SRT
IC6604 ST-BY
10
DEFLECTION 7
CONVERTER +135V 2
5
IC6603
41 VFB2 Q6800 IC9002 3
V DET PROT
MCR51A2
4 6
37 VSAW– 5 VIDEO OUT (GREEN) TO D BOARD
SWITCHING REGULATOR IC6606 39 VSAW–
+5V REG
35 VSAW+ 6
HV(T6803)
3 7 I O +5V
G 33 VSAW+ F FOCUS TO CN9001 1 VB
SS. RST
–15V RECT C BOARD J9001

VG (H)
COCP
COVP
VOCP
–15V 7 Q9010
COM
D6817
2 8 DFT DF DAMP G DRIVE 3 3 VI VO 8
NC
13
VD
SS
CT
VS
D6824
RT
T6801 Q6821
CONTROL BLOCK 3 BUFFER
TO D1 BOARD CN6802
& RELAY DRIVE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 8 SC G2 TO C BOARD

1 9 CN9007 TO E BOARD
7 9 VOF FV
5
+15V +15V RECT 9
CN4500 TO D BOARD
D6816
+135V IC6801 PULS-RECT 12 5 IK FV(T6803)
IC6602 10 DF SW D6809
DETECT STBY RECT M PIN OUT 10
48 M PIN
3 2 Q6809 11
1 OUT1 VCC 8 30 H LIN
Q6810
+10.5 3 1 34 H CENTER H LIN OUT DF ON/OFF SW
IC9003
4 1
Q6816, 6815
2 IN1– OUT2 7
IC6607
POWER MODULE
3 2
IC6613 11 40 HP2 VIDEO OUT (BLUE)
PH6602 IC6608
FEEDBACK 13 14 HP1 DF PROT
4 IC6637
TO A 28 DF DRIVE Q6817, 18
3 IN1+ IN2– 6 4 1
+5V
49 ABL 1 CN9001 1 VB
IC6601
PH6601 +5V STBY 1 Q9011 CN9002 TO D BOARD
4 GND IN2+ 5
REF. VOLTAGE
POWER ON CONTROL CN6802
M-PIN OUT +200V +200V RECT B DRIVE 5 BUFFER 3 VI VO 8 A1
48 D6813
Q6809
CATHODE STANDBY PIN 5 MPIN
IC6608 3 OF CN6605
DETECT MAIN RECT
2 ANODE CN6802 7 VOF
H-LIN OUT
1 OUT3 VCC 8 1 REF
30 Q6801 Q9001 TO D BOARD
HLIN IK 8 5 IK CN9007
BUFFER G2 G2(T6803)
2 IN3– OUT4 7
3 IN3+ IN4– 6
D (POWER SUPPLY, DEFLECTION HV)
4 GND IN4+ 5
DH (MAGNETIC FIELD CORRECTION) F1 (AC LINE FILTER) F2 (AC SWITCH)

F1601 F1602
CN3802 LFT LFT
CN6101 CN1602 CN1651
F1601
N/S (B) 1
TO LCC AC IN 1 1 4 1 4 1 AC OUT 1 1 AC IN
N/S (E) 2 TO D BOARD
IC3805 TO AC CORD CN6604
TO A BOARD DEGAUSS 3 Q3807 NS DRIVE
Q3808 AC IN 2 2 3 2 3 2 AC OUT 2 2 AC IN
CN1138 Q3809, 3812
BUFFER N/S MUTE 3 -IN1 S1651
OUT1 2 POWER
4 +IN1
IC3807 SENSOR
NL3801 XOUT 4 7 -IN2 OUT2 8
6 +IN2
TO BEZEL TO D GND
REF 3 Q3810, 3811
BUFFER
CN3801 RS812 R3811 CN3803
1M 470k
1/2W 1/2W
– 63 – – 64 – – 65 – – 66 –

RM-916 RM-916 RM-916 RM-916
TO H2 BOARD TO H1/H3 BOARD TO J BOARD

TO C BOARD CN9001
CN4101 CN4500 CN1934 CN1901/CN1980 CN8304

CN1195 CN1190 CN1180
EXTRA PARABOLA 1 63 EXTRA-PARA R_OUT 30 1 R OUT
H DEFL 2 59 HS_IN G_OUT 28 2 G OUT
17 CVBS 1 OUT
20 CVBS 2 OUT
14 TVR OUT
AFC PULSE 3 B_OUT 26 3 B OUT
16 TVL OUT
2 KEY 2 IN
7 KEY 1 IN
4 SIRCS
2 LED G
1 LED R
4 RN IN
3 RP IN
2 LN IN
1 LP IN
HD1 4 19 L2_FIL IKIN 25 4 IK
D FOCUS 6 64 DF_PARA
IC4301 CN4502
HD2 9
A (MAIN-MICON, TUVIF, AUDIO AMP)
CN5402
BOARD
TO VM
CRT-DRIVER
V DEFL 12 60 VS_IN VM_OUT 45 3 VM
R100 13 46 VM_MOD IC1205
IC001 DIFFERENTIAL AMP IC1204
VPROT 14 Q4315 16 V_PROT1 500K 15
TO A BOARD CN1401
MAIN CONTROLLER L-AMP

V PROT SW CN1162
L-UB 1 LO L+ 3 CN1193
TO D BOARD DEGAUSS 11 61 DEGAUSS KEY 2 13 OUT 1 1 L SP
XRAY 16 20 XRAY CN4800 CN6800
R-UB 7 RO L- 2
NS ROT 20 52 NS ROT
GREEN 19 35 G2_IN LED 1 54 R+ 5 TO SPEAKER
CN1161
TO D1 BOARD CN6101
1 PROT 1 LED 2 53 R- 6 IC1201 IN 9 IC2200

RED 20 36 R2_IN ABL_IN 22 ST-BY 5 62 ST-BY
TONE-CTRL HP-AMP 4 R SP
4 CPCP TO D BOARD 6 OVP SIRCS 64
BLUE 21 34 B2_IN ABL_FIL 23 CN6605 OVER VOLTAGE PROT. 11
5 HP2 3 OCP KEY 1 7 L-UB
BLK 22 33 YS/YM2 OVER CURRENT PROT. 13 11 LOUT 17 3 1 6 LHP
6 HP1 TU101
TEXT RED 23 41 R1_IN HP100 ATT SW 45 TO H2 BOARD
7 H SYNC R-UB
CN1150 R OUT CN1932
6 5 7 7 RHP
TEXT GREEN 25 40 G1IN VP 100 A20 8 V SYNC AGC MONITOR 16 AGC ROUT 16
9 ABL 1 L OUT
TEXT BLUE 27 39 B1_IN R 30 R AFT1 17 AFT1 DEL OUT
Q101
IC1203
10 PROR 1 BUFFER
R-AMP
TEXT BLK 29 38 YS/YM1 AFT2 18 AFT2 SDA SDA
G 33 G
EW 1 SCL SCL
B 34 B F MONO 23 F MONO IN 9
Y100 36 52 Y1IN NC F MONO
Q002 ST 29 ST
YS 36 YS NC MODE
U100 37 53 CB1IN HD 17 BUFFER
OUT 1
MSP RESET(MSP) 30 MSPR NC (RESET) MSPR
Q001 37 YM
V100 39 54 CR1IN
7
INVERTER MUTE 31 MUTE PLL-SW ST

X
DPIC SW 40 43 DPIC_DCTR IC002 35 I AFT OUT AFT1
1 Q301 Q313 STBY RF AGC AG
RESET IC 9 RESET
TO BUS CONTROLLER
Q4800 - H DRIVE1 MUTE MUTE

5
6
Q4801 - H DRIVE2 SDA

SDA 1 47 5 SDA RF SIGNAL SCL
2 19 B-INT
IC4803 SCL 1 49 6 SCL
CN1100 TU3301
CPC-AMP W PROTECT 40 7 WC
Q3300
IC4802 SDA0 48
IC003
DET OUT Q3301
5 5 PLL AMP AMP.
7 7 SCL0 50 EEPROM
6 6
CN1118
2 2 5 AFT OUT AFT2
1 1 7
3 3 6 SDA
RF SIGNAL
SCL
IC4801 IC4800
2
3
1 E 3 FS IN
FF CONP2 FF CONP2 (RGB OUT, DEFLECTION) 5 B IN

TO V BOARD
1 CN1801
7 G IN
ANTENNA IN SIGNAL
SPLITTER
9 R IN
CP1300
TEXT RED 23
TEXT GREEN 25
TEXT BLUE 27
TEXT BLK 29
CN1140
TO E BOARD
CN1401
– 67 – – 68 – – 69 – – 70 –

RM-916 RM-916 RM-916 RM-916
TO J BOARD TO A BOARD
CN8301 CN1195
IC1801
TEXT DECODER
CN6104
5 QP (–)
CN1801
CN1934
BLAN 50 3 FS OUT
CN6101
KEY 2 IN
BUFFER 5 B OUT
B 49
Q1806
R IN
C IN
6 HP1
Y IN
S IN
L IN
TO E BOARD
IC6104
CN4800
BUFFER
10
11
12
DQP-AMP
1
2
3
4
5
6
7
8
9
H2 G 48 7 G OUT
4 CP CNTL
TO A BOARD CN1118
Q1805
1
(AV INPUT, PRESET KEY, PHONE OUT) CN6103
IC6354 2 2 REF
BUFFER MULTIPLAY
R 47 9 R OUT
TO RT COIL
ROT+ 3 3
Q1804
CN5402
IC6356 1 8 IC6105
N/S. OUT 4 DQP-CONT
ROT- 1
5
US/SC 45 Q1802 Q1803 17 V SYNC TEXT 3 6 2
CN1932 1 Q6107 I
BUFFER BUFFER 5 3 G
DQP H-MOJI
2 HP L IN 5
TO A BOARD
HP R IN CN1193 19 H SYNC TEXT 1 2 3 4 5 6 7 8 9 10 6 IC6353
3 8 5V REG
IC6102
VS 46 DQP-CONT 3
J1931 +
2
CVBS 30 15 CVBS IN 1 3
3
5 IC6351
IC6106
7 DC CONT.
6 H-SIZE CONT
2
S1931 1
3
AUTO PRESET
5
1 2 7
3 4 V (TELETEXT) IC6101
6
QP-CONT CN6100
J1932
1 8
L R J1933 MUTING 10 DF SW
V
J CONTROL LINE FROM MAIN UCOM 2 7
14 HP1
3 6 1 M-PIN
IC8302 Q6106
H3 CXA2069Q 5 2 DF SW
CONST. C
17 N/S
28 DF DRIVE
(TOP KEY) CN1980 L1 2 SCL 3 DF PH 29 FOCUS
30 H LIN
SCL
SDA
CLK DAT CS 3.3V 5V IC1204

H1 (LED, SIRCS RECEIVER) S1972 1 GND R1 4 SDA 4 H-LIN
TO BOARD CN6802
STBY 2 TO A BOARD TDA7481
CN1190
L2 9 L OUT+ 5 QP DV
3 KEY 1 OUT L OUT LCH OUT 34 GND
R2 11 43 L IN L OUT– 6 H-TRP
CN1901 S1973 35 V COMP+
IC1901 PRG+ L3 16 IC8103 AK4524 AUDIO CODEC R OUT+ IC6108
5P 7 QP PH DAC CONT. 39 V COMP-
R OUT
REMOTE SENSOR WHT R3 18 45 R IN R OUT– 37 V SAW-
IC1203 8 QP AC
S-MICRO L4 23 33 V SAW-
TO A BOARD CN1190
S1974 TDA7481
D1906 4 SIRCS PGRM- MON L 9 CP CTR 41 VFB2
SPB-26MVWF R4 25 52 MCLK LRCK BCK SDI SD0 RCH OUT 44 H CENT
DVDL 59 10 H-CENT 46 H-SAW
Q1901 IC1205 IC1201
G 2 LED2 S1975 MON R
LED DRIVER DVDR 61 54 11 QP AV
R VOL+
DIFF. AMP TDA7315D
48 M PIN
Q1902 TVL 62 AUDIO 12 QP DC
STBY
LED DRIVER
1 LED1
S1976
TVR 64 PRCESSOR A 49 ABL 1
ON VOL- MCLK LRCK BCK SD0 SDI Q6128

IC8105 H-SAW Q6125
J8106 DIR AMP H LIN AMP 1
S1977 DIR TC9446F-002 Q6126
DIGITAL IC8106 IC6103
H LIN AMP2
TV/VIDEO AUDIO DIGITAL SIGNAL PROCESSOR M.PIN CONP
AUDIO IN SCL SDA P001 (ALIVE) 3.3V 1
2
3 2
S1978 1
3
ENTER 7
5 14 11 10 9
7
1 6 IC6201
IC6202
S1979 5 LPF V SIZE COMP
MENU D1
CONTROL LINE FROM MAIN UCOM A1 (AUDIO DSP) (DF, DQP DRIVE)
2 3 4 5 6
– 71 – – 72 – – 73 – – 74 –

RM-916 RM-916 RM-916 RM-916
J CN8304
B3 IC602
IC802
(YCT, COMB FILTER, 50 Y MAIN OUT

(DRC, MID, DRC/MID CONTROLLER) 64Mbit SDRAM
16Mbit SDRAM
IC8306
MAIN COLOR DECODER
VIDEO/AUDIO-IN/OUT) 47 U MAIN OUT
2.5V 3.3V
44 V MAIN OUT
42 V PULSE MAIN OUT 2.5V 3.3V
VS 4 IC8308
V
HS 9 2 IC8312 4 SUBCOLOR DECODER 41 H PULSE MAIN OUT 54MHz
38 Y SUB OUT H
AND GATE
YOUT 21 FL8314 35 U SUB OUT
2 SYNC IN 34 V SUB OUT 54MHz
17.28MHz
CbOUT 22 FL8315
32 V PULSE SUB OUT IC601
CrOUT 23 FL8316 Y 8
IC8313 2 SYNC IN 31 H PULSE SUB OUT TO A BOARD
CV OUT 1 11 Y FOR SYNC VS 4 27 CVBS OUT TEXT CN1180
Cr-Y 8
Y IN 3 1 CVB S/Y 11 Y FOR SYNC 20 CVBS 1 IN
HS 9 2 4 IC801
TO BC4A BOARD 48 C1 IC8311 17 CVBS 1 IN DRC 1chip
C IN 5
CN2001 AND GATE 8
BUFFER
16 TVL IN (CXD2090Q) Cb-Y IC901
V
14 TVR IN Y
C OUT 15 Q8302 39 C3 19 Y1 IC501 DRC process
Clamp pluse Clamp pulse
525i n 525p MID-X
41 CVBS/Y3 4 RN OUT Cr-Y
IC8314 18 CB1 (CXD9509Q)
3 RP OUT 525i n 1050i
Y IN 1 44 CVBS/Y2 Y Y 8
625i n 625p Cb-Y
DAC LPF
17 Cr1 2 LN OUT IC302 FF process Cb-Y CXD2309
C IN 4 43 C2 Yin 625i n 1250i
1 LP OUT Chroma P and P
TO SBX3005-11 CV OUT 6 C2 43 8 Cr-Y ADC
Cr-Y ADC Cr-Y
46 FSC OUT C2 44 Decoder LPF CXD2306 P in P 54MHz
FSC 9 Cin TLC5733
Y
(CXA2123) T and P clock
ACPN 11 CrOUT 23 8
C2 1 Cb-Y Cb-Y Index
19 Y1 CbOUT 22
clock
Scan Convert
18 Cb1 YOUT 21 3 IC8310
IC8309 7
17 Cr1 SCP 10 SW 13.5MHz
1 SC 19
1
17 IC303 PLL
chroma decoder
6 YIN H CXA3106
Q8329 16 PLL HREF 5.0V 3.3V
8 -UIN WPLLHD
From sub
TLC29321
IC8302 AV/SW AMP
Q8330 H
Q8331 Y Level
BUFFER
AMP
9 -VIN IC603 54MHz
47 COUT2 Clock
Q8332 V converter
Yin Sub Cr-Y
LTI
To MID-X
J8301 BUFFER PLL

Chroma Cb-Y RPLLHD TLC2933
36 DC OUT LOUT2 43
Cin Decoder
4 3 3 Y1 ROUT2 45 IC504
(CXA2123) H
2 1 STV 60
5 C1
V
TV 63 I2C
7 S1
5.0V IIC BUS
V1 1 V1 LTV 62 5.0V
Video In 1 Monitor Out Expander
L1 2 LV1 RTV 64
R1
(CXA1875)
4 RV1 VOUT1 53 Q8301 V J board
LOUT1 52 L IC604 Sub µ com
V2 8 V2 ROUT1 54 R
(IIC BUS)
L2 9 LV2 RVS 31
IC902
R2 11 RV2 LVS 29 Q8304
Video In 2 BUFFER
30 VS
Q8305
V3 15 V3
L3 16 LV3 V/YOUT2 44 Q8304
BUFFER
R3 18 RV3 VOUT3 41 Q8306
BUFFER
Video In 3 59 LV6 YOUT3 39 Q8308
BUFFER
61 RV6 COUT3 37 Q8309
BUFFER
25 RV4
23 LV4
28 S-4
26 C4
24 Y4
22 V4
Y B-Y R-Y L R
Component In
R IN 1
L IN 3
Y IN 5
CV IN 7
S IN 8
C IN 9
CN8301
TO H2 BOARD
CN1934
– 75 – – 76 – – 77 – – 78 –

IC2004 IC2003
CN2001 3D COMB FILTER MEMORY
CV CV CV
COMP V IN 1 LPF BUFF 88 AYI
Y Q2018, 2019, FL2004 Q2014 2 36
Y OUT 3
C OUT 5 C
BUFF 76 CSI MIO0 13 5 39 IO1
J BOARD TO Q2011, 2013, 2015
IC8313 RESET 6
BPF
S DAT 9 Q2012, 2016, FL2003
96 ACI MIO15 28
7 31
IO16
S CLK 10
10 34
C IN 15
Y LPF Y
16
Q2004, 2005, 2008 84 AYO
Q2010, FL2002
1
BPF
– 79 –
83 ACO MA0 19 AO
C Q2003, 2006, 2007
Q2009, FL2001 C 9
MA8 22
A8
57 RSTB 99
59 SCL 26
60 SDA MWE 11 13 WE
IC2005 47 FSC0 MRAS 98 14 RAS
BUFF
+3.3V REG Q2002 MOE 12 27 OE
MZAS 10 28 U CAS
+5V 1 0 +3.3V XI 30 29 L CAS
50 FSC1
X2001
20MHz
XO 31
BC4 (Y/C SEP AUTOWIDE)
KV-ES29M90
RM-916

KV-ES29M90
RM-916
VM (VM DRIVE)
CN5402 CN5401
1 QP-
2 QP-
TO NECK ASSY
TO D1 BOARD QP(+) 3 3 QP+
CN6104
– 80 –
QP(-1) 4 4 QP+
TO E BOARD Q5400, 5401 Q5402 Q5406

VM 9 Q5403 Q5407
7 VM
CN4502 VM AMP
Q5404 VMOUT 8 VM
Q5405
BUFFER

6-2. FRAME SCHEMETIC DIAGRAMS
TO SBX3005-11
CN2001
DY COMP V IN 1
(Y/C SEP AUTOWIDE)

LP 1 NC
J8307 J8305 J8304 J8303 J8302 E 2
LN 2 2P 3P
Y OUT 3
RP 3 J8301
1 CV OUT
6 CV OUT
10 NT/PAL
6 RESET
E 4
15 C OUT
11 APCN
RN 4
BC4
2 GND
4 GND
12 GND
14 GND
3 GND
5 GND
8 GND
9 SDA
5 C IN
4 C IN
9 FSC
3 Y IN
1 Y IN
10 SCL
1
11 +9V
13 +5V
C OUT 5
R-Y
B-Y
PR
PB
R3
R2
1R
7 NC
8 NC
V3
V2
1V
L3
L2
1L
G2 KB KG
2 5V
7 9V
R
R
V
L
5
L
A GND
3
CN8100
1 DGC CHK
2 DGC CHK
10P RESET 6
R-SW 6
4
1 R IN Y IN 7
1 DGC
3 DGC
DIGITAL
2
2 N.C.
L-SW 7
AUDIO CN8302 CN8303 2 GND MN/NT 8
DSP ALIVE 8
(AUDIO DSP)
H.DY H.DY V.DY V.DY IN

H CN8200 CN8201 3 L IN S DAT 9
COAXIAL SIG 9
COAXIAL GND 10 CN6602 CN6603
#
:WHT
#
:WHT J CN8301
4 GND S CLK 10
A1
2P 3P :S-MICRO :S-MICRO 9P 5 Y IN 9V 11
:MINI WHT (YCT, COMB FILTER, VIDEO/AUDIO-IN/OUT) WHT-L 6 GND E 12
10 COAXIAL GND
GND 1 :S-MICRO :S-MICRO

9 COAXIAL SIG
HV G4 G1 KR CV CN8304 7 CV IN 5V 13
3.3V
8 DSP ALIVE
2
50P 8 S IN E 14
CLK 3 V+ 6 5 AC IN :BTOB
5 A GND
6 R-SW
9 C IN C IN 15
7 L-SW
1 GND
7 GND
10 GND
2 3.3V
6 6.5V
8 SDA
4 DAT
4
3 CLK
9 SCL
DAT V- 5 4 N.C.
4 RN
3 RP
5 CS
2 LN
CN6604
1 LP
Y MAIN OUT 50
GND 49
GND 48
U MAIN OUT 47
TRAP 46
GND 45
V MAIN OUT 44
GND 43
V-PULSE MAIN OUT 42
H-PULSE MAIN OUT 41
GND 40
GND 39
Y SUB OUT 38
GND 37
GND 36
U SUB OUT 35
V SUB OUT 34
GND 33
V-PULSE SUB OUT 32
H-PULSE SUB OUT 31
COMB RESET 30
+10.5V IN 29
+10.5V IN 28
CVBS OUT (TEXT) 27
GND 26
DSP ALIVE 25
SCL 24
SDA 23
GND 22
GND 21
CVBS 2 IN 20
GND 19
GND 18
CVBS 1 IN 17
TV L IN 16
GND 15
TV R IN 14
+6.5V IN 13
+6.5V IN 12
CS 11
DAT 10
CLK 9
+3.3V IN 8
+3.3V IN 7
GND 6
GND 5
RN OUT 4
RP OUT 3
LN OUT 2
LP OUT 1
CS 5 H- 4 5P 3 N.C.
CN6801
6.5V 6 CN8101 6P :VH
H- 3 2 N.C.
10P
GND 7 H+ 2 1 AC IN
SDA 8 CN1934
H+ 1
CN1652 5P CN1651 4P CN1602 2P 12P
SCL 9 RED
WHT:VH WHT:VH :VH R IN 1 :S-MICRO
GND 10
1 1 2
F2 F1
AC OUT AC IN AC OUT GND 2
(AV OUTPUT, PRESET KEY, PHONE OUT)

CN1604 J1931
200V 1 AC OUT 2 2 AC IN AC OUT 1 GND
1P L IN 3
CN9003 N.C. 2 CN6804
:TAB
1P (AC LINE GND 4
CN9002 4P (AC SW)
31 H-PULSE SUB OUT
32 V-PULSE SUB OUT
GND 3 30 COMB RESET
27 CVBS OUT (TEXT)

41 H-PULSE MAIN IN
4P
42 V-PULSE MAIN IN
:TAB :S-MICRO
20 CVBS 2 OUT
17 CVBS 1 OUT
Y IN 5
29 +10.5V OUT
28 +10.5V OUT
WHT 1 FILTER)
25 DSP ALIVE
AC IN
13 +6.5V OUT
12 +6.5V OUT
1
H1 4
47 U MAIN IN
50 Y MAIN IN
44 V MAIN IN
14 TV R OUT
16 TV L OUT
35 U SUB IN
38 Y SUB IN
34 V SUB IN
E 1 CN9004 :S-MICRO
3
GND 6
8 +3.3V-D
7 +3.3V-D
AC IN 2
4 RN IN
1
46 TRAP
3 RP IN
1P 200V G2
2 LN IN
CV IN 7
1 LP IN
1 GND
49 GND
48 GND
45 GND
43 GND
40 GND
39 GND
37 GND
36 GND
33 GND
26 GND
22 GND
21 GND
19 GND
18 GND
15 GND
6 GND
5 GND
23 SDA
CN1601 2P
10 DAT
4
24 SCL
9 CLK
:TAB
11 CS
E 1 NC
2
2 :VH S IN 8
FOCUS
3 E C IN 9 J1932
4 H1 CN1195 1 GND GND 10
CN1116 CN1180 3P
CN9007 1 +5V STANDBY +5V STANDBY 1 1P 2 KEY2 IN KEY 2 11 V
1 G2 50P WHT
GND 1 1P 2 2 :FASTEN 3 GND
GND GND :BTOB :S-MICRO GND 12
H2
(CRT DRIVE)
R 2 CN9007
NC 3 STANDBY STANDBY 3
1P FOCUS
B 3 4 GND GND 4 L
1 R DRV 10 PULL UP PULL UP 6 J1933
1 PROT PROT 1 5 5 CN1161
C
CN6605 AC ON/OFF AC ON/OFF

10P 9 HP MUTE HP MUTE 5
CN9005 2 E 2 N.C. NC 2 10P 6 OVERVOLTAGE PORT OVERVOLTAGE PORT 6
3P CN1193 8 AU GND AU GND 4
3 G DRV 3 N.C. NC 3 7 OVERCURRENTPORT OVERCURRENTPORT 7
WHT 10P R
CN9001 7 R HP R HP 3
4 E 4 135V 135V 4 8 NC NC 8 WHT
:S-MICRO 9P 6 L HP
5 B DRV :S-MICRO L HP 2
BLK 5 135V 135V 5 9 NC NC 9
:S-MICRO 6 E 5 GND HP GND HP 1
6 N.C. NC 6 10 GND GND 10
4 R SP S1931
7 12V 7 N.C. NC 7 CN1932
3 AUDIO GND AUTO
8 IK 8 SDA2 SDA2 8 TO SPEAKER 6P
PRESET
(POWER SUPPLY DEFLECTION, HV)
2 AUDIO GND WHT

9 E 9 SCL SCL 9
1 L SP :S-MICRO
10 DF–SW DF–SW 10
11 N.C. NC 11
12 12V 12V 12
13 AFC PULSE AFC PULSE 13
A1 GND GND A1
14 HP1 HP1 14 1 +17V
CN6608 B1 GND GND B1
15 EX PARA EX PARA 15 2 GND (AUDIO)
3P +17V 1 A2 GND
3 -17V GND A2
16 10.5V 10.5V 16
GND (AUDIO) 2 B2 GND GND B2
D
17 N/S N/S 17
-17V 3 A3 GND GND A3
18 10.5V 10.5V 18 1 +6.5V +6.5V 4 B3 GND GND B3
19 GND GND 19 2 +6.5V +6.5V 5 CN1160 A4 GND GND A4
6-3. CIRCUIT BOARDS LOCATION
20 –15V –15V 20 10P
CN6103 3 GND GND 6 B4 MID-BUSY MID-BUSY B4
3P 21 GND GND 21 CN6606
BLK 4 GND GND 7 A5 FPD FPD A5
22 7P
5V 5V 22
ROT– 1
:S-MICRO
23 6.5V 6.5V 23
5
6
+10.5V
GND
+10.5V
GND
8
9
B5 GND
A6 HP 100 IN
GND B5
HP 100 OUT A6
C
CY COIL
24 6.5V 6.5V 24
2 7 +30V +30V 10 B6 VP 100 IN VP 100 OUT B6
25 GND GND 25
ROT+ 3 A7 Y 100 IN Y 100 OUT A7
D1 26
27
GND
GND
GND 26
GND 27
CN6805
1P
1 GND B7 GND
A8 U100 IN
GND B7
U100-OUT A8
(DF, DQP, DRIVE) 28 DF DRIVE DF DRIVE 28
B8 GND GND B8
29 FOCUS FOCUS 29
CY+ 1 A9 V100 IN V100-OUT A9
CY COIL
CN6102 CN6100 30 CN6807

3P H LIN H LIN 30 1 GND
NC 2 50P 1P B9 GND GND B9
WHT :BTOB 31 VM VM 31
CY– 3 :S-MICRO CN6808 A10 DPIC SW DPIC SW A10
32
33
GND
V SAW+
GND 32
V SAW+ 33
1P
CN6809
1 GND
A B10 GND GND B10
(DRC, MID, DRC/MID CONTROLLER)

1 GND A11 RESET 100 RESET 100 A11
34 GND GND 34 1P (MAIN-MICON, TUVIF, AUDIO AMP)
35 V COMP+ V COMP+ 35 CN6817
1P
1 GND CN1108
B11 GND
A12 SDA
GND B11
SDA A12
CN502 H3
36 15V PULSE 36 50P
37
15V PULSE
V SAW– V SAW– 37
50P
:BTOB
B12 SCL
A13 +5V DIGITAL
SCL B12
+5V DIGITAL A13
:BTOB
VM H2
CN6802
38
39
GND
V COMP–
GND 38
V COMP– 39
50P
:BTOB
B13 +2.5V +2.5V B13 F1
A14 +3.3V +3.3V A14
40 HP2 HP2 40
B14 +5V 5V B14
41 VFB2 41
B3
VFB2
1 SCA 2 SDA 1 A15 H-PULSE SUB OUT H-PULSE SUB IN A15
135V 1 42 GND GND 42
2 SCL 2 SCL 2 B15 GND GND B15
NC 2 43 GND GND 43
3 +12V +12V 3 A16 +9V +9V A16
QP (+) 3 44 H-CENT H-CENT 44
NC 4
CN6104
45 GND GND 45
4
5
GND
GND
GND
GND
4
5
B16 VP SUB OUT
A17 V SUB OUT
V-PULSE SUB IN B16
V SUB IN A17
A B3
QP (–) 5 8P 46 H-SAW H-SAW 46
6 GND GND 6 B17 GND PORT 2 B17
NC 6
GND 7
:S-MICRO 47 9V
48 M PIN
9V 47
M PIN 48
7 AFC PULSE FLYBACK PULSE 7 A18 U SUB OUT U SUB IN A18 A1
8 GND GND 8 B18 GND PORT 1 B18
9V 8 CN6101
10P
49
50
ABL1
PROT
ABL1 49
PROT 50 CN6800
9 EXTRA PARA EXTRA PARABOLA 9
CN1162
A19 Y SUB OUT Y SUB IN A19 E
:S-MICRO 10 HD2 HD2 10 20P B19 GND GND B19
20P
11 DEGAUSS DEGAUSS 11 A20 GND GND A20
PROT 1 10
PROT 1 1
REF 2
–15V 3
CP CNTL 4
HP2 5
HP1 6
GND 7
5V 8
ABL 1 9
12 GND GND 12 B20 GND GND B20

13 HD1 HD1 13 A21 Y-MAIN OUT Y-IN A21
14 X-RAY X-RAY 14 B21 GND GND B21 H1 DH
15 FOCUS DYNAMIC FOCUS 15 A22 U-MAIN OUT U-IN A22
CN4901
4P
16 VM
17 VSAW+
VM MODULATION 16
VERTICAL SAW1 17
B22 GND
A23 V-MAIN OUT
GND B22 D1 E1
V-IN A23
RED 18 VPROT VERTICAL-PROT 18 B23 GND GND B23
:S-MICRO
19 VSAW– VERTICAL SAW– 19 A24 V-PULSE M OUT VP-IN A24
F2 BC4
9V 1
20 N/S NS ROT 20 B24 GND GND B24 D
GND
HD IN
2
3
A25 H-PULSE M OUT HP-IN A25 J
B25 GND GND B25
E1
1 PROT 1
10 PROT 1
HD CLAMP 4
9 ABL 1
3 –15V
7 GND
4 CPC
2 REF
5 HP2
6 HP1
8 5V
( H OUT
PROTECTION ( CN4800
1
2
EXTRA PARABOLA
H DEFL
EXTRA PARABOLA
HORIZONTAL
1
2
1 GND GND 1
6-4. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS
10P 2 +5V +5V 2
1
YEL
:S-MICRO
3 AFC PULSE FLYBACK PULSE 3
3 FS IN Note: Reference information
9V FS OUT 3
• All capacitors are in µF unless otherwise noted.
4 4
GND 2
HD1 HD1
4 4 RESISTOR : RN METAL FILM
5 FPD FPD 5
HD IN 3
6 D FOCUS DYNAMIC FOCUS 6
5 B IN B OUT 5 • All electrolytic capacitors are rated at 50V unless otherwise noted. : RC SOLID
HD CLAMP 4 6 6 CN1801
7 +12V +12V 7 20P • All resistors are in ohms. : FPRD NONFLAMMABLE CARBON
(This model not using)
7 G IN G OUT 7
8 8 :BTOB
V SAW+ VERTICAL SAW+
8 8 kΩ = 1000Ω, MΩ = 1000kΩ : FUSE NONFLAMMABLE FUSIBLE
(TELETEXT)
9 HD2 HD2 9
10 V SAW– VERTICAL SAW– 10 CN1118
9 R IN R OUT 9 • Indication of resistance which does not have rating electrical : RS NONFLAMMABLE METAL OXIDE
R OUT 1 10 10
*V
GND 2
11 GND GND 11 20P
11 GND GND 11
power is as follows. : RB NONFLAMMABLE CEMENT
12 V DEFL :BTOB
VERTICAL DEF 12
G OUT 3
13 R100
12 GND GND 12 Pitch: 5 mm : RW NONFLAMMABLE WIREWOUND
R100 13
GND 4 CN4500
9P
14 VPROT VERTICAL PROTECT 14
13 GND GND 13
Rating electrical power 1/4W (CHIP: 1/10W) :* ADJUSTMENT RESISTOR
B OUT 5 14 SCL SCL 14
GND 6
BLK
:S-MICRO
15 ABL-CTR ABL-CTR 15
15 CVBS IN CVBS IN 15 • : nonflammable resistor. COIL : LF-8L MICRO INDUCTOR
16 XRAY X-RAY 16
+12V 7
17 B100 B100 17
16 SDA SDA 16 • ¢ : internal component. CAPACITOR : TA TANTALUM
•
IK 8 17 V SYNC TEST V SYNC TEXT 17
18 GND GND 18 : panel designation or adjustment for repair. : PS STYROL
NECK ASSY GND 9
E CN4101
19 GREEN
20 RED
GREEN OUT 19
RED OUT 20 CN1140 CN1100
CN1138
4P
CN1190
7P
18 GND
19 H SYNC TEXT
GND 18
H SYNC TEXT 19 • All variable and adjustable resistors have characteristic curve B : PP POLYPROPYLENE
QP QP VM
(RGB OUT, DEFLECTION) 40P 21 BLUE BLUE OUT 21 40P 4P BLACK WHT 20 +9V +9V 20
unless otherwise noted. : PT MYLAR
:BTOB WHT :S-MICRO :S-MICRO
• Readings are taken with a color-bar signal input.
:BTOB
22 BLK BLANKING OUT 22 : MPS METALIZED POLYESTER
CN5402
GND 1
B INT 2
SDA 3
SCL 4
SCP 5
R100 6
B100 7
L. C. MUTE 1
GND 2
6.5V 3
10.5V 4
KEY 1 IN 7
GND 6
GND 5
SIRCS 4
STBY +5V 3
LED G 2
LED R 1
23 TEXT RED TEXT RED 23

11P no mark : PAL : MPP METALIZED POLYPROPYLENE
WHT 24 GND GND 24
Q.P.– :S-MICRO 25 TEXT GREEN TEXT GREEN 25 ( ) : SECAM : ALB BIPOLAR
Q.P.+
1 135V 26 GND GND 26 [ ] : NTSC 3.58 : ALT HIGH TEMPERATURE
TO LCC
E
VM
2 NC
3 QP (+)
27 TEXT BLUE
28 GND
TEXT BLUE 27
GND 28
« » : NTSC 4.43 : ALR HIGH RIPPLE
• Readings are taken with a 10 MΩ digital multimeter.
(VM DRIVE)
4 NC 29 TEXT BLK TEXT BLK 29

• Voltage are dc with respect to ground unless otherwise
VM
5 QP (–) 30 GND GND 30 TO BUS CONTROLLER

6 NC 31 SCL2 SCL 31
QP– 1
7 GND 9V/12V 1 CN4502 32 SDA2 SDA 32
noted.
CN1901
KEY 1 OUT
• Voltage variations may be noted due to normal production

DEGAUSS
NC 2 CN3802 CN1980
STBY+5V
8 9V 3P 33 9V +9V 33 5P
TO NECK ASSY
GND 2 WHT 6P 3P
N/S (B)
N/S (E)
QP+ 3
SIRCS
WHT * V Board not used this model

LED 2
LED 1
9 9V/12V VM 3 :S-MICRO 34 SCP SCP 34 BLK WHT-L

tolerances.
GND
GND
GND
11V
QP+ 4 :S-MICRO
NC
7V
35 GND :S-MICRO :S-MICRO

10 GND GND 35
GND 5
11 VM 36 Y100 Y-100 OUT 36
• All voltages are in V.
1
2
3
4
5
6
3
2
1
5
4
3
2
1
•
GND 6 CN5401
37 U100 U-100 OUT 37 ✻ : Cannot be measured. Note: The component identified by shading and
VM
VM
7
8
8P
:BTOB 38 GND
39 V100
GND 38
V-100 OUT 39
DH H3 H1 • Circled numbers are waveform references. mark ! are critical for safety. Replace only with
40 DPIC SW DPIC SW 40
(MAGNETIC FIELD
TOP KEY
(LED, SIRCS • : B + bus. part number specified.
CORRECTION) RECEIVER) • : B – bus.
• ÷ : signal path.
– 81 – – 82 – – 83 – – 84 –

PRINTED WIRING BOARDS
A [MAIN-MICON, TUVIF, AUDIO AMP]
A BOARD WAVEFORMS A BOARD IC2603 PQICG2032FZ – A Board (Component Side) –
1 2 3 4 5
V IN 1 2 V out
5.0Vp-p (V) 4.0Vp-p (V) 0.2Vp-p (V) 0.2Vp-p (V) 0.2Vp-p (V)
6 7 8 9 10 Vo CONTROL ON/OFF
CIRCUIT CIRCUIT
PWM COMP. 5 ON/OFF

5.0Vp-p (V) 5.1Vp-p (H) 2.6Vp-p (H) 2.9Vp-p (H) 2.3Vp-p (H)
+
SOFT START
11 12
–
CIRCUIT
OSSCILATOR
Q
4.8Vp-p (H) 4.9Vp-p (V)
F/F R
S
OVER CURRENT ERROR AMP.

DETECT CIRCUIT – 4 O ADJ
+
VREF
THERMAL
PROTECTION
CIRCUIT
3
COM
• :Pattern from the side which enables seeing.

• :Pattern from the rear side.
A BOARD IC001 CXP750096-012Q A BOARD IC2604 PQ5EV3 – A Board (Conductor Side) –

EXTAL
XTAL
INT0
INT1
INT2
RST
TEX
VDD
VSS
TX
DC IN (V IN) 1 2 DC OUT (Vo)

INTERRUPT CONTROLLER
PORT A
A/D CONVERTER SPC700α11 CLOCK GENERATOR

AN0 ~ AN5 6 CPU CORE /SYSTEM CONTROL 8 PA0 ~ PA7 CONTROL
6CH
CIRCUIT
ON/OFF CONTROL (Vc) 5 4 V OUT ADJUSTMENT PIN

PORT B
RMC REMOCON FIFO

RAM RAM 8 PB0 ~ PB7 3
96K/120K BYTES 2496 BYTES
SI
SERIAL INTERFACE
SO
PORT C
UNIT 6 PC0 ~ PC5*

SCK
8-BIT TIMER/ 2 PC6 ~ PC7*

EC 2
COUNTER 0
PORT D
TO 8-BIT TIMER 1 A BOARD (Component Side) A BOARD (Conductor Side)

8 PD0 ~ PD7
XLC IC TRANSISTOR IC DIODE
EXLC 2
PRESCALER/ IC001 B-9 Q1201 D-12 IC100 G-10 D300 A-9
R TIME-BASE TIMER 2 PE0 ~ PE1 IC002 C-8 Q1206 D-13 IC901 I-13 D301 B-9
PORT E
G IC003 A-8 Q1209 D-13 IC1203 G-1 D302 B-6

2 PE2 ~ PE3 IC1201 E-13 Q1210 D-13 IC1204 B-1 D1205 F-1
B ON-SCREEN
I DISPLAY 3 PE4 ~ PE6 IC1203 F-13 Q1205 E-13 IC2600 E-7 D2200 E-3
WATCHDOG TIMER IC1204 B-13 IC2601 F-4 D2201 D-3
YS IC1205 F-12 DIODE IC2603 F-5
PORT F
YM IC2200 E-12 IC2604 F-6

8 PF0 ~ PF7 D1208 E-13
HSYNC 32kHz IC2600 E-8
D1209 D-11 TRANSISTOR
VSYNC IC2601 G-10
TIMER/COUNTER
IC2603 F-9
Q101 G-11
IC2604 F-8
PORT G
HS0 Q301 D-4

HSYNC COUNTER 0 5 PG3 ~ PG6*, PG7
Q313 D-4
2 Q902 I-13
Q2200 D-3
I2C BUS 8-BIT PWM 8CH Q2201 E-4
14-BIT PWM 1CH
HS1 HSYNC COUNTER 1 INTERFACE UNIT (6CH) Q3300 F-11
8 (6)
(PWM0 ~ PMW5)
SDA0
SDA1
SCL0
SCL1
ADJ
PWM
PWM0 ~ PMW7
– 85 – – 86 – – 87 – – 88 –

(1) Schematic Diagram of A Board
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
TO SPEAKER
CN1190
A CN1138 7P
STBY +5V
L.C.MUTE
CN1193
AUDIO GND
AUDIO GND
# CN1195 WHT 10P
KEY2 IN
KEY1 IN
HP MUTE
3P :S-MICRO
PULL UP
SIRCS
WHT
LED G
LED R
AU GND
GND HP
10.5V
WHT :S-MICRO
GND
GND
GND
GND
GND
TO H1(CN1901)/
RN IN
6.5V
RP IN
TO MAGNETIC COIL
LN IN
LP IN
:S-MICRO
R HP
R SP
L HP
L SP
TO H3(CN1980) TO H2 BOARD CN1932
TO H2 BOARD CN1934
C1222 C1224
10
1
D012
1
2.2 2.2
MA111-TX 6.3V 6.3V
CN1161
PROTECTOR B:CHIP B:CHIP
10P
DIP PIN IC2600 C1225 R2201
D007 C1223 R2200 D2200
BA09T 2.2 2.2 4.7k C2200
RD5.6SB3 68 10 RD9.1SB
TO D BOARD +9V REG 6.3V 6.3V :CHIP :CHIP
PROTECTOR D008 B:CHIP B:CHIP PROTECT
STBY +5V
STBY +5V
CN6605 MA111-TX +
- - +
B 12.2 9.0 PROTECTOR

D013 R2205
SIRCS
R2204
KEY2
KEY1
LED2
LED1
10k R2207
C2209
GND
GND
GND
GND
1 +5V ST-BY I O +9V RD5.6SB3 R2203
+6.5V
+10.5V
100
+5V STANDBY R2202 10k
+10.5V
:CHIP 4.7k
L.C.MUTE
C1284 C1283
RN
RP
LN
68
LP
G PROTECTOR 4.7k :CHIP :CHIP
C2600 C2601 :CHIP 2200p 2200p IC1203
2 :CHIP
GND C2612 C2613
9.0
CH:CHIP CH:CHIP
4.5
0.1 0.1
-0.3 (0)
TDA7481
2.4 (0)
:CHIP 100 0 100 :CHIP 4.4
-0
MODE
3 ST-BY
BOOT
VREG
FREQ
-15.9
ST-BY R-AMP
RN
-VCC
-VCC
-VCC
RP
25V 25V
LN
GND
LP
OUT
VCC
-8.0
VCC
-8.0
G RSP
-19
-19
5.9
9.9
G LSP
B/D
IC1201
-19
F/C
NC
19
19
C2202
-0
R2206
IN
0 0
R SP
:CHIP
L SP
GND 4 TDA7315D013TR 10 8 7 6 5 680k
R1241 R1242 TONE CTRL :CHIP R1286
AC ON/OFF 5 AC ON/OFF 10k 10k 4.5 C2201 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 10k C1226 C1241
C1214 FB1205
:CHIP :CHIP 10 :CHIP # 0.1
OVER VOLTAGE R PS1202 1.1UH
4.7k
6 OVP R1202 220 :CHIP 470 :CHIP B:CHIP
PROT. SCL 2.7A
4.7
C1207 C1208 CREF SCL
SUB-HP-AMP
20
(ASF)
NJM4560M
CH:CHIP
OVER CURRENT 0.1 100 0
AUDIO(R)
C1247
+17V
0.1mF
7 OCP 16V
R1201 220 :CHIP SDA
IC2200
16V
R2208
PROT. C1206 9V SDA L R1280
C2203
19
R1248
CH:CHIP
4.4
C1242
4.4
2
4.5
C2615 C2616 B:CHIP R1261
-0
C1287
C2602 R1249 C1288 22 -0 150 R1240
100p
NC 8 100 # # 100 12k 100p 0.1mF 150 33k
GND DGND :CHIP
18
:CHIP CH:CHIP
B:CHIP
C1243
16V :CHIP :CHIP :CHIP CH:CHIP AUDIO(L) C1246 :CHIP :CHIP C1244
9 C1205 4.5 R1279 220 :CHIP 1 2 3 4
0.1
NC R-UB L
F:CHIP
0.47 C1276 2200
C
LOUT
B:CHIP
+5V 0.0022mF 50V CH:CHIP TRE(L) C1245 C1271
C1251
R1237
17
0.0047
4
6.8 5.0 AUDIO(R) 16V C1281
GND 10 0 R1278 220 :CHIP 33k 0.1 680p 680p (SXE)
(MUSE) R B:CHIP 0.1
+6.5V I O +5V C1204 TRE(R) ROUT :CHIP B:CHIP B:CHIP B:CHIP
16
5
4.5 R2215 R B:CHIP
G 0.0022mF 50V CH:CHIP C1213 0.037mF 25V B:CHIP R2211 47k
6.3V
8 7 6 5 RIN BO(R) R2210
15
10k R1264
6
C1212 47k :CHIP
4.5 R2209
CH:CHIP
:CHIP 470 AU GND
B:CHIP
C1250
C2603
FB1208
RO
C1289
VDD
2.2mF 6.3V B:CHIP
1.1UH
R+
0 R1204 :CHIP C1248
100p
680k
AUDIO(R)
LO(R) BI(R) :CHIP
#
R-
14
100 -0 0
7
0 R1282 C1294 0 C1211 18k :CHIP R1236 R1238 2200
2.2
16V
4.5
# # 0.033mF 25V B:CHIP :CHIP R2212 C2205 12k 22k (SXE)
4.5
C1202 NC BO(L) Q2200
13
IC2601 10k :CHIP
8
:CHIP :CHIP 4.5 2.2 C1249 :RN-CP C1253 R1239
0.1 C1210 0.47 16V B:CHIP :CHIP DTC144EKA-T146 R1235 C1282
C2204
BA05T 4.5 6.3V 5.6k FB1206
GND
LO(L) BI(L) 0.001mF # 0.1
12
R1255 16V MUTE4 C1219 0.1
9
+5V REG F:CHIP CH:CHIP B:CHIP :CHIP 1.1UH
LO
B:CHIP C2206 :CHIP 2.2 B:CHIP

4.5
4.5
12k
4.5
L+
4.5
L-
R1284 10
4.5
0 NC LIN -17V
10
11
:CHIP
PROTECT
R1250 0
RD9.1SB
C1285 3.9k :CHIP C1252 PS1204
D2201
+3.3V-DIGITAL 1 2 3 4 R2213 R1243 R1244 C1277
PROTECTOR
L2603 100 :CHIP 4.5 R1203 100p L1204 2.7A
L1202
:CHIP
6.8 1.4 16V 47k # 10k 2200p
L2600 L2601 L2602 18k CH:CHIP
RD9.1SB
C2607 :CHIP :CHIP CH:CHIP
D1205
:FPRD 0
AUDIO(L)
C1296 C1201 :CHIP
+5V 1 5 #
C1295 L
3.3 R1256 # 0.1 R1285 C1297 6.9
:CHIP C1254
47k
CN1160 R1254 10k C1203 :CHIP # # 1 C1256
D
16V
CH:CHIP
CH:CHIP
D2600
CH:CHIP
2 4 C2609 R C2207 0.47 0.1W B:CHIP 1

C1291
C1292
:CHIP
C1290
C1286 12k L1201 2.2 :CHIP :MPS

100p
100p
100p
10P D5S4M
R2601 470 :CHIP B:CHIP :MPS 0.47mF R1266
C2614 1.5k 100 :CHIP 16V 50V 1k
DIP PIN
R2214
3 1.2 6.3V
16V C2208 0.47 0.1W B:CHIP 0
470
DTC144EKA-T146
:RN-CP F:CHIP C1209 :CHIP
SP MUTE
10V 2.2 Q1205
+3.3V
MUTE5
TO D BOARD 0 C1257
Q2201
C2608
R1253
C1293 R1283 16V C1255 DTC144EKA-T146
CN6606 R2600 1000 # 0 F:CHIP 0.001 # MUTE
IC2603 4.7k
IC1205 :CHIP :CHIP :PT 0
4.7k 6.3V :CHIP B:CHIP
:CHIP PQ1CG2032FZ C1278 5.9
+3.3V REG R2602 #
DIFFERENTIAL AMP
G RSP
+17V 1 +17V C2606 910 L-UB CH:CHIP R1276
R SP
C2605
R-UB
L-UB
0.068 :RN-CP 22k
470 R1205
GND(AUDIO) 2 AU GND 25V R1258
10V R1257 R1259 :CHIP 47k
B:CHIP 12k 0
100 10k :CHIP
-17V 3 -17V :CHIP :CHIP :CHIP C1216
Q1206 2200mF
+6.5V 4 +6.5V
R1247 2SC2712-YG 25V
33k MUTING
+6.5V 5 IC2604 +3.3V IC1204 :CHIP
PQ5EV3 TDA7481
E GND 6 +9V
+2.5V REG L-AMP Q1207
+3.3V
2SC2712-YG
MODE
GND 7
BOOT
VREG
FREQ
+3.3V
-VCC
-VCC
-VCC
GND
OUT
-8.0
VCC
VCC
-8.0
9.9
MUTING
5.8
-19
-19
B/D
-16
-19
F/C
NC
19
19
0 0 0 0
IN
+10.5V +2.5V 0
+10.5V 8 3.3 0
3.3
R2603
5.9 D1208
GND 9 1 5 2.2k 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
2.4 1.2 MA111-(K8).S0
:RN-CP C2611 C1273
+30V 10 +30V 2 4 220 PS1201 R1206
0.1mF
R2604 16V 2.7A 47k
C2610 CH:CHIP
AUDIO(L)
3 2.2k -0 :CHIP
0.1
:CHIP +3.3V :RN-CP
C1258
0 0.1 C1215
B:CHIP 470
PS1203 2.7A C1217
R1265 (ASF)
470 2200mF
:CHIP 25V
L D1209
MA111-(K8).SO
C1259
C1260 STBY MUTE
F
0.1 +9V
0.47 C1262 B:CHIP
16V 0.001mF
B:CHIP +9V
CH:CHIP C1221
C1270 R1260
R1270 100
680p 150
C1261 :CHIP 47k 16V
B:CHIP Q1209
# :CHIP 9.0
CN1162 R1281 2SC2712-YG
B:CHIP C1274 Q1211
20P 150 PROTECTOR
1000p 0 2SA1037
CH:CHIP :CHIP
PROTECTOR
+9V R1271
TO D BOARD R1272 1k
FB1207
C1275
1.1UH
B:CHIP
C1263
0.0047
R1245 C1220 680p 1k :CHIP 9.0
CN6800 2.2 -0
# B:CHIP :CHIP R1277
9.0 0
:CHIP 4.7k
R/G/B(TELETEXT) 9.0 :CHIP
SDA CN1118
SDA 1
#
SCL
SCL 2 TO V BOARD 0
+5V ST-BY
C1264 R1246 C1265 R1273
PROTECTOR
-0
G CN1801 100p 12k
2SC2712-YG
0.1 4.7k
+12V 3 +12V CH:CHIP :RN-CP B:CHIP R1275 R1267 :CHIP
Q1210
R1269
22k 15k
GND 4 1 GND L1203 100
:CHIP :CHIP
:CHIP
GND 5 +5V 2 +5V
BLKT +5V L1205 R1251
C1298 C1267 C1279 C1272
GND 6 3 FS IN 1
#
100
Q004 0.001 2200p
DE(3) C033 :MPS C1266 :FPRD R1252 CH:CHIP 25V
2SC2712-YG B:CHIP
FLYBACK PULSE 7 4 0.1 # 10k CP1300
BT B:CHIP BLANKING C1268 :CHIP C1280
R083 SpLITTER RF
GND 8 5 0.47mF #
B IN 1k
AC ON/OFF
50V CH:CHIP +9V

DE(4)
DEGAUSS
:CHIP Q003
L.C.MUTE
EXTRA PARABOLA 9 6
2SC2712-YG R087
DE(15) GT C1269 # :PT
ST-BY
220 ANT IN MAIN OUT
+9V
HD2 10 7 G IN BLANKING :CHIP
G LSP
SUB OUT
L SP
DEGAUSS 11 DEGAUSS 8
R084
RT 1k R085 C034 R086 ATT SW BST +B GND
12 9 +5V
H
GND R IN :CHIP 4.7k 220p 10k
DE(6) :RN-CP CH:CHIP :CHIP 1 2 3
HD1 13 10 C1302
CN1108 +5V 0.1
L1300
DE(13)
X-RAY 14 50P 11 IC002 +9V B:CHIP
GND
STBY MUTE
DE(7) :BTOB S-80743AL-A7-S
DYNAMIC FOCUS 15 12 GND
SP MUTE
SP PROT
TO B3 BOARD RESET L001
DE(12)
CN1108
+5V
VM MODULATION 16 13 GND
LED1
LED2
R093 NS ROT
SIRCS
DE(8) SCL
4.9 (0)
4.9 (0)
17 14 10k
JB(7)
VERITCAL SAW1
STBY +5V
SCL :CHIP
DE(9) CVBST V
0 R094 FB1300 C1301 C1300
VERTICAL-PROT 18 A1 GND 15 CVBS IN 10k 0 100 #
DE(10) SDA R001 R002 :CHIP :CHIP 16V 16V
GND 1 2 3
:CHIP
19 B1 16
:CHIP
VERTICAL SAW- SDA R047 R003 220 220

1k :CHIP
:CHIP
VP100 +5V 220 # :CHIP :CHIP C007

20 A2 17
CVBS2
AFT2
NS ROT NS ROT GND
V SYNC TEST :CHIP SP PROT 100 ATT
220
16V
220
C001
B2 18
1k
GND GND TV R
# R069 R012
R008
I
HP100 :CHIP 4.7k 4.7k IC100
A3 19 C031 C002
R059
R040
R053
R089
GND H SYNC TEXT 4.7k :CHIP TV L

L005 :CHIP S-80743AL-A7-S
0.1 # :CHIP
AUDIO(R)
FB006
:CHIP
FB007
MSP-RESET
FB008
CN1140 B3 GND +9V 20 +9V 16V R066 AFT1

TU3301
40P B:CHIP R068 1k C006 FSS BTF-LG436
:BTOB 6 A4 GND :CHIP 0.1 1
10k GND
AUDIO(L)
MID-B R013 B:CHIP
C030 :CHIP
4.7k C008
B4 +5V
64
63
62
61
60
59
58
57
56
55
54
53
52
MID-BUSY
TO E BOARD 1 .BLK05A5 R009 R011 #
+5V :CHIP TU101 CN1116
4.8
4.9
# R010 4.7k L002 B:CHIP
NC
0 JR109 FSS BTF-WG442

H50
CN4101 A5 1P
DEGAUSS
LED1
FPD JL001 4.7k L OUT

SIRCS
4.8
LED2
R106
NS ROT
:CHIP
0
0
0
:CHIP
ST-BY
0
ABL-CTR
R3300 #
1.0
R007
L.C.MUTE
# :CHIP
AC ON/OFF
DE(4) # :FASTEN
0.8
0.3
4.4
1 B5 # 560 1 2 3
AUDIO PROTECTION
EXTRA PARABOLA GND R OUT :CHIP

HS C021 4.9 0 :CHIP :CHIP JR105
L OUT
HP100 HP100 0.01 MODE # TO F1 BOARD
2 A6
51
HORIZONTAL MODE NC
(-0) (0)
HP 100 IN
-0 (0)
1
B:CHIP B-INT READY :CHIP

4.5 R3304 R OUT
DE(3) VP100 SCL CN1604
3 B6 -0 #
50
FLYBACK PULSE VP 100 IN SCL0 RV3300 SDA

2
R051 1k :CHIP 0 4.9 R079 100 :CHIP R014 100 :CHIP :CHIP 1k D100 NC
DE(6) BE(1) R101 100 :CHIP
HD1 4 A7 OCP SDA1 MA111-(K8).SO
49
Y 100 IN SCL
3
FB001
OCP SDA
R025 220 :CHIP 4.9 (0) 4.3 R078 100 :CHIP R004 R005 C005 TV SDA
3DAT SDA
5 B7 100
48
FPD GND SO SDA0 100 220p NC R102 100 :CHIP

4
SCL
J DYNAMIC FOCUS 6
DE(7) BE(2)
A8
3CLK
R026 220 :CHIP
SDA1
4.9 R077 100 :CHIP R015 100 :CHIP :CHIP :CHIP B:CHIP
R104 # :CHIP
SCL
47
U 100 IN SCK NC
5
0 R3374 FMONO
R052 1k :CHIP FB002 R076 100 :CHIP 0 NC
+12V 0 (4.9) C004 Q3300
7 B8
46
+12V GND OVP :CHIP NC R100 # :CHIP

6
OVP 0 220p MODE

R031 220 :CHIP R017 1k :CHIP 2SA1037
4.9
NC
4.9
DE(8) BE(4) HP100 0 ATT

4.9
1 0 B:CHIP
8 7 A9 ATT SW AMPLIFIER
45
VERTICAL SAW + V 100 IN H SYNC PLL-SW

7
R048 MSPR
R033 220 :CHIP 0 IC001 0.8 (1.1) C014 47 R3362 JR1301 NC(RESET)
DE(15) 10k VP100 0.3
9 B9 EMI 8 7 6 5 100
44
HD2 GND 0 DET OUT

8
:CHIP V SYNC CXP750096-012Q 0.8 (1.1) JR1302 ST

R070 220 :CHIP FB003 :CHIP :CHIP PLL-SW
WC
DE(10) BE(3) 4.9 MAIN CONTROLLER L3302

VCC
SDA
FL001 #
SCL
10 A10 C032 C013 JR107

43
VERTICAL SAW - DPIC SW 5V R114 R115

EEPROM(A0-A7)
JR102
9
JR001
M24C08-MN6T
RESET EMI :CHIP 0

0.01 0.01 0 # # 0 DET OUT
R044 C009 R042 -0 VSS B:CHIP :CHIP :CHIP :CHIP :CHIP
11 B10 B:CHIP
10
42
GND GND +5V X001 :CHIP NC

IC003
4.7k VSS GND

VS 0.1 CSA20.00MXZ040 0 :CHIP 5V
VP100 RESET 100 C028 :CHIP 2.4 -0
12 A11 25V VDD TV
11
41
VERTICAL DEF RESET 100 0.022 C3330 NC

XTAL C3331
GND
B:CHIP B:CHIP 2 4.9 C016 47p CH:CHIP 0.1 100 NC

DE(12) 2.3
-0
-0
-0
R045
-0
E0
E1
E2
13 B11
12
40
VM MODULATION GND D002 16V 16V NC R105

R056 0 :CHIP 4.7k L003
R071 100 :CHIP EXTAL 4.7 D006 MA111-(K8).SO 0 NC
VERTICAL DE(9) SDA :CHIP B:CHIP
14 A12 EXLC 1 2 3 4 :CHIP
13
39
SDA MA111-(K8).SO OSD(YS)SW NC

PROTECT KEY2 :CHIP
5.0 KEY2 2.5 NC
OSD(YM)SW
K 15 B12 XLC C017
14
38
ABL-CTR SCL NC
SCL 0 :CHIP KEY1 C011 R072
KEY1 R024 3.9k :CHIP C3337
DE(13) R057 C003 4.9 2.6 (0) 0 68p CH:CHIP NC
# 100 #
16 A13 # :CHIP
15
YM
37
X-RAY +5V +5V DIGITAL Q002 GND

:CHIP :CHIP 4.5 NOISE DETECT :CHIP
5 R091 NC
AGC 5.4 0 2SC2712-YG 100 L3303 C106
17 B13 YS
16
36
GND +2.5V +2.5V AFT OUT

R034 # :CHIP AGC MONITOR R080 YS-BUFFER :CHIP # GND
AFT1 0
(2) 4 0 R081 YS :CHIP
30 MSP RESET(SAP)
18 +3.3V-DIGITAL A14 I 3.9k

17
35
GND +3.3V 100 9V

AFT1
4.9
:CHIP 0 R090 L101

G(OSD) G AFT2 R037 220 :CHIP 4.9 :CHIP 8 7 6 5 AFT OUT
5.0 (2.2) R082 R023 100 C3338 C3336
19 B14 B
18
34
GREEN OUT +5V Q001 5V VIF

WC
AFT2 470 100 470p 100

VCC
:CHIP
SDA
SCL
R(OSD) R036 220 :CHIP 9V

25 RESET 100
R JB(1) INT
27 DSP ALIVE
0 :CHIP :CHIP 2SA1037 JR002 B:CHIP 16V

24 MID-BUSY
R103
22 COMB RESET
26 CHIP SEL
20 A15 0
(4.9)
19
G
33
RED OUT H-PULSE SUB OUT 0 RF AGC

AGC
-4.9 (0)
0SD(INTENSITY)SW
23 F MONO
B(OSD) C010 R046 220 :CHIP FB004 # VIF

B -0(0) :CHIP
4.9 (0)
2.3 (0)
R022 C3302 :CHIP

BLUE OUT 21 B15 0.1
-0(0)
B-INT
31 MUTE
D003
28 TRAP
GND R110
-0(0)
FB005 220 :CHIP #

0.6
0.1
4.9
25V R075 IC004 560 RF AGC

YS 3 MA111-(K8).SO CVBS1
-0
R092
0
29 ST
GND
0
BLANKING OUT 22 +9V A16 +9V B:CHIP 1.8k M24C04-MN6T :CHIP C103 C107
32 R
R050 :CHIP OSD(B) SW 220 C108

E0
E1
R(TELETEXT) B(OSD)
E2
RT JB(3) R021 0 B :CHIP EEPROM(A8-AB) 0.1 470p

# +9V RV100 R109 100
23 B16
20
21
TEXT RED VP SUB OUT

R3320 B:CHIP B:CHIP
:CHIP C015 # 470 16V
JB(4) R035 2.2k :CHIP 1 2 3 4 1k +9V
R073 10p :CHIP :CHIP
24 A17 V SUB OUT G(OSD)
:CHIP
GND
:CHIP
1k :CHIP
G
1k :CHIP
1k :CHIP
:CHIP
L
R049 C018 C019 C020 1.8k R3323 C101
G(TELETEXT) GT # 100
Q101 C104 #
R067 0.01 0.01 0.01 :CHIP L105
TEXT GREEN 25 B17 GND
10k :CHIP B:CHIP B:CHIP B:CHIP R074 R038 :CHIP AS 2SA1037AK 100
JB(5) :CHIP 1.8k R020 C012 R018 680 SDA BUFFER 16V
1k
R016
220
GND 26 A18 U SUB OUT :CHIP SDA R111

1.8k :CHIP 2.2k 10p 680
B(TELETEXT) R3334 100 :CHIP 100 AS
BT :CHIP :CHIP :CHIP :CHIP D004 SCL
R027
R019
:CHIP
R029
R028
TEXT BLUE 27 B18 GND R062 SCL

R006
1k MA111-(K8).SO SDA
C024 R058 L3304 +9V SDA
JB(6)
RESET 100
GND 28 A19 Y SUB OUT :CHIP 10p 0 R055 OSD(G) SW +5V 5V R112 100 :CHIP
SCL
:CHIP :CHIP 0 :CHIP L3305 +5V SCL
BLKT
R(OSD)
FMONO
TEXT BLK 29 B19 L102

MID-B
GND +30V 30V

R065
COMB
D005
MSPR
L3306 +5V 5V
680
DSP
MA111-(K8).SO
3CS
GND 30 A20 GND :CHIP +9V 9V L103

ST
8 OSD(R)SW +30V 30V

R
SCL
SCL 31 B20 GND L104
SDA JB(12) D014 D001 +9V 9V
SDA
C3352 C3353
32 A21 Y MAIN OUT MA111-(K8).SO 470p 100
JR2601 0 :CHIP MA111-(K8).SO
VOLTAGE SHIFT B:CHIP 16V
:CHIP
# :CHIP
:CHIP
1k :CHIP
MUTE
SP MUTE
+9V 33 +9V B21 GND

SCP JB(11) D302
M 34 A22 C3350
SCP U MAIN OUT MA111-(K8).SO
STBY MUTE
C3355 C3354 470p

C3351
220
220
9 MUTING SW 47 47
470p B:CHIP
GND 35 B22 GND D301
R030
B:CHIP
D300
R032
+3.3V-DIGITAL
BE(1) JB(10) MA111-(K8).SO C111 C114 C109 C113 C110 C112

R060
R054
Q313
-0.2
Y-100 OUT 36 A23 V MAIN OUT MA111-(K8).SO 470p 47 470p 47 470p 100
VOLTAGE SHIFT 0 2SC2712
BE(2) STBY MUTE B:CHIP B:CHIP B:CHIP 16V
U-100 OUT 37 10 B23 GND MUTE
+10.5V
11.8
JB(9)
38 A24
12
GND V-PULSE M OUT

C301
BE(4) 11 1000 11.8
V-100 OUT 39 B24 GND
16V
B-SSS10133-HK.-A..-ES29
470k :CHIP
BE(3) JB(7) D317

DPIC SW 40 A25
R301
H-PULSE M OUT MA111-(K8).SO 0

B25 GND
ST-BY MUTE Q301
R302
47k 2SA1037
12 :CHIP MUTE
+10.5V
C1227
+9V #
R088 R095 R096
R303 C326
N 1k 1k 1k
10
( )
:CHIP :CHIP :CHIP 47k
R061
100
:CHIP C1228
#
MAIN MICON,TUVIF,
:CHIP
BE(1)
GND
AUDIO AMP
COMB
Q005
SDA
DSP
SDA
SCP
SCL
SCL
3CS
TV R
B 100
R 100
CVBST
3DAT
CVBS2
CVBS1
3CLK
INT
+6.5V
TV L
2SA1037AK
JB(9)
JB(7)
JB(6)
JB(5)
JB(4)
JB(3)
JB(1)
JB(12)
JB(11)
JB(10)
Y 100 BUFFER R098

RN IN
RP IN
LN IN
AUDIO(R)
LP IN
AUDIO(L)
100
BE(2)
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
R063
100 Q006
:CHIP 2SA1037AK R097
100
100
100
100
100
100
100 TV
BE(3) B-Y100 BUFFER :CHIP
R099
100
R117
R043
R039
R041
R116
R118
R064 :CHIP
100 Q007
:CHIP 2SA1037AK
O R-Y100 BUFFER
50
GND 49
GND 48
47
TRAP 46
GND 45
44
GND43
42
41
GND40
GND 39
38
GND37
GND36
35
34
GND 33
32
31
30
29
28
27
GND 26
25
SCL 24
SDA 23
GND 22
GND 21
20
GND 19
GND 18
17
16
GND 15
TV R OUT 14
13
12
CS 11
DAT 10
4
GND 1
2
SDA 3
SCL 4
SCP 5
6
CLK 9
8
GND 6
GND 5
4
1
GND
R 100
RN IN
RP IN
B 100
TV L OUT
LN IN
LP IN
B INT
COMB RESET
+3.3V-D
+3.3V-D
+6.5V OUT
+6.5V OUT
CVBS 2 OUT
Y100
CVBS 1 OUT
U SUB IN
Y SUB IN
V SUB IN
Y MAIN IN
DSP ALIVE
U MAIN IN
R-Y100
B-Y100
V MAIN IN
+10.5V OUT
+10.5V OUT
CN1180
V-PULSE SUB OUT
H-PULSE SUB OUT
CN1196 CN1100
CVBS OUT (TEXT)
V-PULSE MAIN IN
H-PULSE MAIN IN
4P 7P 50P
WHT WHT :BTOB
TO J BOARD
TO BUS CONTROLLER
CN8304
– 89 – – 90 – – 91 – – 92 –

(2) Schematic Diagram of D Board
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
A
PFC OUT
CN6607
PFC IN
C6672 C6673
2
.BLK001D
.BLK0589
.BLK003C
.BLK0026 T6601
2200p 1kV :R 2200p 1kV :R
SRT
R6660 D6628
B TH6603 4.7 :FPRD

+5V
5 10ELS2N-TA2B5
NTC
DETECT RECT C6649
100
JW6601 C6647 25V
D6619 C6635 D6623 .BLK043D
7.5MM #
D6616 D6617 RD12ESB1 100p P6KE200AG23 4 6
U05G U05G C6630 18V CLAMP
9.6
CLAMP L6601
STBY RECT STBY RECT 22 4.9
450V Q6613
3 7 I O DTC114ESA
D6621 G IC6607 4.0
C6634 C6601
10ELS2N-TA2B5 D6627 DM-58
(-27.6)
100 C6648 100 0
JW6602 18V RECT D1NL20U-TR 470 0 IC6606 25V +B CONTROL
7.5MM 2 8 25V BA05T
D6650 STBY RECT
C6637 R6677
1SS119-25 22p 470 +5V R6699 0
-20.2
STOPPER 2kV R6671
D6642
-18.6
#
1 9 1k 1SS119-25
R6639 R6642 R6645
C6622 :RN STOPPER
C6617 1 C6629 470k 0.1 C6625 R6675
1200 R6657 8 7 6 5 D6622 4.9
0.0047 15W # 1/2W VD6601 1/2W 0.022 10k
10.9
134
250V 22
17.9
2.4
500V ENE471D-20A :RF 630V UF4005PKG23 3 +5V
C 4.2 0
E
0 SNUBBER Q6607 R6697 R6698
-85.0 -85.1 R6694
C6607 VD6603 C6645 2SA1175-HFE 120k 10k 10k
JW6603 0.1 1 IC6605 4 3 2 1 0
470p # C6613 D6605 :RN
2.8
250V 0.0047 # D6613 TL431CLP D6635
D4SB60L 4.9
-84.9
-85.1
-81.7
500V U05G IC6604 AC DETECT RD18ESB
AC RECT
-85
E JW6604 TOP209 2
PROTECT C6623 R6688 OVP SW
CN6604 C6608 # R6670
2.8
# C6646 R6684 1k 0
DTC114ESA
C6633 D6630 D6638
5P 470p C6614
C6619
6.8k 0.01 -20.5 R6676 R6679 C6653 # :FPRD
Q6612
0.0047 D6612 47 1 2 3 4 :RN 1SS119-25
:VH 250V
0.0047
11k 47k 0.0047 0 #
500V JW6606 U05G :RN STOPPER R6693
E 500V
TO F2 BOARD # PROTECT 18k
0 C6657 :RN 0
CN1652 D6620 #
0.6 CN6606
# C6675 D6629 Q6611
R6638 JW6605 # 7P
AC IN 5 C6621 R6641 1SS119-25 DTC114ESA
.BLK062C 1 # R6681 WHT
1200 470k STOPPER R6685
R6686 R6622 15W
250V 1/2W 0 10k :S-MICRO
N.C. 4
.BLK062B R6678 2.2k
8.2M 0.47
1W 10W
IC6603 10k
N.C. 3
.BLK00AA MCR5152 :RN Q6608 TO A BOARD
:RB
D N.C.
AC IN
2
1
C6671
0.022
630V
2SC2500-B C6660
1mF
50V
R6600
0
:CHIP +5V
CN1160
-31.1 (-0)
RY6603 R6500 1 +6.5V

DJ12D1-0(M) TV-8 .BLK04ED
.BLK04EA
0.47
JW6654
*(-3.9)
*(-1.8)
-81.3
10W
-83.9
2 +6.5V
-82.3
-83.1
-82.9
-85.0
-85.1
*(7.6)
-85.0
-78.8
-85.1
-85.1
-82.3
-74.6
-84.9
84.1
SS.RST
#
JW(5MM)
JW(5MM)
:RB
COCP
VG(H)
COVP
VOCP
FB6604
CN6603 JW6655
VG(L)
FB6601
VC-1
VC-2
COM
RY6602 +5V
GND
OUP
N.C.
N.C
# 3 GND
VD
SS
CT
RT
VB
VS
3P DJ12D1-0(M) TV-8
WHT .BLK058C .BLK058B
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 4 GND
:S-MICRO
TH6601
D6625 5 +10.5V
TO DGC RD13ESB2
C6628
D6639 6 GND
CLAMP R6704
DGC 1 470p 1kV :HR 0.47 10ELS2N-TA2B5
.BLK0077
.BLK054A
.BLK0005
.BLK0549
1/4W 15V RECT 7 +30V
N.C 2 R6609 C6641 :FPRD
680k R6615 R6632 R6636 R6653
680k 2.2M 1/2W 0.1 :MPS
680k 680k D6643 C6674
DGC 3 :RN :RN :RN 7 2 330
R6648 R6650 R6707 UF4005PKG23
R6608 330k :RN 25V
E R6614 D6603 330k :RN 2.2k STOPPER D6634 CN6608

680k 680k R6631 R6635
C6602 RY6601 :RN 2SA1175-HFE 680k 680k C6640 L6602 D4SBS6 3P
:RN R6656 330k :RN 9 1 WHT
0.033 DH12D2-0(M) :RN :RN 470p AUDIO RECT +6.5V
630V R6607 R6613 1kV :S-MICRO
R6619 R6630 R6634 :HR
680k 680k
DGC CHK 1 470k R6652 16k :RN C6659 +10.5V
:RN :RN 680k 680k TO A BOARD
:CHIP C6639 1000p CH:CHIP R6668 6 18
:RN :RN 3300
DGC CHK 2 C6627 0.01 B 47 :CHIP 25V
D6626
R6612 R6618 C6609
R6606 1mF
C6632 4.7 UF4005PKG23 1 +17V
120k 75k
CN6602 75k R6623 R6637 BOOST UP 3 PS6604
:RN :RN 50V C6676 # L6603 C6664
2P +12V :RN 33k 56k JW(5) 2 GND(AUDIO)
+17V
C6644 # 1kV :HR 0.01
:RN :RN +10.5V +30V
:MINI C6667 +5V
D6645 # R6666 1k :RN-CP
#
3 -17V
R6605
120k
IC6602 R6629 R6633 17
C6663
C6626 0.0082 :PP C6658
:RN 75k 36k C6643 1000p CH:CHIP CN6609 PS6605 0.01 R6696
3300
REF.REGULATOR :RN :RN 1P 5A 25V R6689 22k -17V
R6651 2.4k :RN +5V 4.7 3W
D6601 16
1SS119-25 C6612 10 C6631 10 D6633
C6642 CN6611 PS6603
D10SC4M JW(5) 1 +5V STANDBY
F
10 1P
6.5V RECT C6666
D6624 15 0.01 2 GND
D1NS4 R6663
CN6610 PS6606
C6677 0.22 D6640 3 STANDBY
R6628 NOISE UP 1P 5A PS6602 L6606 +5V
+6.5V
0.022 D6608 3W RD30ESB2
MA111-(K8).SO
STOPPER
1k :RN
10k JW(5)
25V :RS 14 4 GND
MA111-(K8).SO 30V CLAMP
D6604
OUT1 :CHIP R6710

B:CHIP C6654
10
1
VCC PROTECT C6662 0.47

3300 5 AC ON/OFF
R6621 R6665 CN6612 1P L6607 47 5W D6641
R6601 16V
10k 16V
C6638
2.2M D6644 RD6.8ESB2 C6668 OVERVOLTAGE

# R6701
R6661
:CHIP 1/2W 13 47 6
IN1- OUT2 10k C6636 R6674
D10SBS4F PROTECT PROT
STOPPER
MA111-(K8).S0
# 220 L6605 25V OVERCURRENT

:CHIP CN6613 10.5V RECT 7
D6602
.BLK007F PROT
4.9
1P
MA111-(K8).SO
STOPPER
R6662 12 8 NC
.BLK0080
R6664
D6606
Q6601 0.22 3W :RS D6637

3
IN1+ IN2- # PS6607 PS6601

12.3 2SC2785TP-HFE Q6614 CN6614 5A 1SS119 9 NC
JW(5) C6661
R6625 2SA1175-HFE D6609 1P FB6602
0 47 STOPPER
RD12ESB1
SPEED UP
68k LATCH 1SS119-25 R6672 R6673

11 16V 4.9 10 GND
D6648
Q6603 C6655
MA111-(K8).SO
C6650
RELAY SW
PROTECT
4
GND IN2+ :RN-CP R6667 2.2k JW(5)

2SA1175 330p 1000 -0
R6611 PH6602
D6610
R6602 R6617 Q6604 470 C6670 25V

4.7k 1kV R6692 270 CN6605
G 1k 390k R6620 R6647 ON3171-R 330p Q6609

0 :RN-CP D6607 2SA1175-HFE 10 :HR
:RN-CP 470k
R6643
150 1kV DTA144ESA 10P
:RN-CP MA111-(K8).SO 1W WHT
-78.1
-78.3
22k :HR OCP SW

STOPPER -78.2 :CHIP :RS -74.8 Q6606 R6691 :S-MICRO
C6604 74.6
-74.8
-74.6
R6687 L6604
2SB733-34
1
47 OUT3 VCC T6602 470k

# R6616 -85.0
2SC2785-HFE
R6627 VCC SWITCH CN6615 1/2W +6.5V
D6651 100k R6702
2SC2785-HFE
Q6610
:RN-CP 150k 68k
DTZ-TT11.24B C6603 1P TO A BOARD
PROTECT
:RN-CP
Q6602
OUT4 :CHIP 0
1SS119-25
:CHIP #
D6615
R6690
2
R6610 IN3- -75.0 FB6603 C6652 0

D6632 -78.7 R6646 R6658 10k CN1161
100k R6644 10k C6651 330 R6683
-85.0
*(-84.0) :RN-CP MA111-(K8).SO R6640 4.7k 10k

330p 160V 220k
Q6615 R6604 :CHIP R6655 :CHIP C6669
LATCH 22k :CHIP R6649 1/2W D6636
10k CATHODE 10k 330p 1kV
3
UN2211
-75.1
IN3+ IN4- :CHIP 4.7k

D6806 :RN-CP -85.0 :CHIP
:CHIP 1kV :HR 0 1SS119-25
:CHIP D6649 -84.6 R6669 JR6602
ANODE C6618 C6620 PH6601 +5V :HR OCP SW
2
1SS119-25 0.01 MA111-(K8).SO -85.0 1k #

C6606 C6610 100p
D6611 Q6605 ON3171-R
STOPPER1 REF
C6605
100p B:CHIP CH:CHIP R6703 STOPPER R6659
2SC2712-YG
1
# 100p GND IN4+ JR6603 D6631 R6680 R6682

CH:CHIP # MA111-(K8).SO 10k C6665
-82.0 CH:CHIP D6614 R6654 0 D4SBL20U CN6616 CN6618 0.27 820 10
R6603 R6626 C6624 STOPPER :CHIP
RD12ESB1 47k :CHIP 1P 2W
+10.5V
D6618 1P C6656
10k IC6601 100k 100 -85.2 :CHIP +B RECT
R6864 R6865 16V SPEED UP 0.1
180k
:RN-CP :RN-CP MA111-(K8).SO
22k
H R6820
4.7k
:CHIP
R6861
0
:CHIP
D6808
DAN202K
STOPPER2
R6862
:CHIP :CHIP
+10.5V
C6611
1000p
C6615
100p
C6616
100p
R6624
100k
POWER ON SW
+10.5V
R6695
#
+10.5V
D6807 22k
CH:CHIP CH:CHIP CH:CHIP :RN-CP
RD3.6ESB1 :CHIP
R6867
-0 LEVEL-SHIFT 0.1 4.7k
8.8 :CHIP IC6608
0.1
R6821 C6863
+135V
# 10
R6868
+6.5V
0 4.7k
0 TO CRT ANODE
-0 Q6820 0 :CHIP
0
2PD601A-Q-TX 1 HV
C6878 0
10
V-PROT MAX R6850
Q6811 0.47 .BLK063A
16V 0 R6869
DTC144EKA-T146 :BP Q6821 560k +135V 1/4W R6853
PS6801 :FPRD L6806 0.47
V-PROT 2SA1037AK-T146-R :CHIP 1.6A Q6808
-15V 1/2W
0 V-PROT MINI 135 R6822 2SC5480-01 C6838 :LHL08 :FPRD
*
5.6k T6804 .BLK003B R6835 680p
I PIN-OUT C6855
L6801 2W R6827 HDT 0.22 1.5k 33
Q6819 R6870 4.7mH :RS 3.3k 1 3W :PP 4
160V
DTC144EKA-T146 2.2k :LHL10 2W :RS *
Q6802 T6803
INVER :CHIP D6813
135 IRF720-LF49 * NX-4522
H CENT OUT ELIZ R6849
7 2 0.47
2
IC6800 C6816 +135V C6823
C6832 200V RECT
+10.5V
REF-VOLT
VCC(OUT)
JW6803 6800pF 1/4W

-15V
OUT-PUT
R6837
DRIVE-IN
STV9379 0.047 0.047

-12.1
:FPRD
-15.3
FB-PLS
5MM 1.5kV C6848

14.1
10
13.5
-0.5
400V 200V C6857

1.3
1.3
V-OUT R6825 62.6 3W 0.1mF L6802 L6803

VCC
C6819
VEE
:MPS :PT 6 3 0.2 C6837 C6853 470p 5

330 1 -0.3 :RS 250V # 2.2mmH G4
680p 470p 500V
C6825 R6831 C6830 1.5k 500V B
1 2 3 4 5 6 7
# 10k # :PP B
3 1 1/2W R6852
# :CHIP
500V
1 R6829 B :FPRD 5 4 C6851 D6817 0.47 6 C6860
C6822 0 L6805
3 1k C6842 1W T6801
470p 47 S3L20UF4 220pF
C6805 B Q6806 0.47mF 160V :LHL08 :RS F DFT L6808 D6820 D6821
C6827 -15V RECT1 2kV Q6812
330 2 2 6 250V 3.3mmH
+135V 2SD774-34 330p .BLK062F
.BLK062E
.BLK062D B ERA38-06 ERA38-06 2SC3840(3)
+9V 25V CN6812 7 1 GND
C6807
500V .BLK0635 :LHL10 SNUBER

-15V H DRIVE 2 CN6811 D6824 13 DF DAMP 76.8 DF OUT
1P .BLK0584 B C6831 R6846
1P C6846 220k S3L20UF4 C6858
4.BLK0634 3 CN6805
4 Q6804 6200pF -0.7 1P
J C6803 1.5kV C6835 0.18mF 1/2W -15V RECT2 470p R6873

2SC2785-HFE 8 SC 2
+9V
# C6868 Q6807 680p 250V 500V 150k TAB

R6823 1.5k +135V
:CHIP
0.01 .BLK0585 H CENT AMP 1 C6821 T6802 .BLK0631 2SC5480-01 B 1/2W C6867
3.3k R6826 R6834 :PP C6859 6 1
B:CHIP HDT 0 0.47
5 2W 2.7k 0.047 1 0.22 H-OUT 150p 0
R6804 C6809 8.8 200V R6839 2kV C6866 100V
:RS
:PP
2W 3W C6845 9
3.9k 1000p 6.7 :PT 100 B 330p :MPS
C6811 R6819 :RS 0.22mF
:CHIP B 330 2.2k -0 C6829 :FPRD Q6810 C6856 L6804
R6859 R6872 C6865 500V
T6800 250V 470 R6851 12 R6863 C6862 B
IRF1830G
C6834
25V 150k 0.022 R6875

470 25V
1.5k
C6806 7 2 100pF :LHL08 0.47 2.2k 2.2k R6866

25V 0.022 1/2W 400V 1k
H LIN OUT
134
100 2kV 1/2W 1W

23.3 10 1W 200V 3.3k 1 GND
470k :RN
100V 6.7 R6836 D6816 :PP

:FPRD :RS :RS :PP C6864
-15V 10 2.9 +200V
R6818
6.7
6.7
680p
D6805 1.4 S3L20UF4 0.0022

3W 11 CN6807
C6814 C6884 R6824 C6818 -0.3 L6807 630V
RD15ESB1 330
6 3 :RS 13.8 +15V RECT .BLK0639 :PP
1P
2.2 2.2 1 75.2 2.2mH
C6854
CLAP R6830 TAB

10V 10V R6844 :LHL08
B:CHIP 10k 100
B:CHIP 0 1/2W 0 0 +6.5V CN6813 CN6814 1 GND
D6803 1/4W R6842
Q6803 :FPRD 5 4 # # 10k
R6802 S3L20UF4 10.9 R6817 R6828 C6820 0 R6884 CN6808
D6801 C6802 C6808 C6833
:PP
V-BOOST R6812 2SA1175-HFE # 1k 470p C6824 C6841 D6812

10k 0.0047 100k Q6809 1P
C6800 :RN
1SS119-25 0.01 0.22 -0.5 0 3.3k H CENT AMP 2 B # C6826 0.12 R6840 C6879 R6854 R6856 R6857 R6860 R6903
B:CHIP 100V Q6805 100V 2SK2251 RD15ESB1 4.7 10k 330k 22 TAB
10 CLIP 500V 330p .BLK0630
.BLK0633
.BLK0632 250V # 10k 10k
100V
:MPS 2SD774-34 :PP PROT 160V 3W

C6810 B 500V :PP M PIN OUT
Q6801 GND
K H DRIVE 1 C6828 1
C6804 0.1 L6800 B R6833 R6838
C6801 100V IRF620 +135V 1M 0.001mF
R6880 # 47k
1 R6904 :MPS PONP UP :RN 200V CN6809
0.01
6.8k :CHIP :LHL08 :RN

R6816
+135V
R6801 CN6816 CN6817 CN6818 1P

:RN-CP
:RN # R6905
10k 120k R6855 27k
4.7 1P 1P 1P TAB
R6807 C6812 IC6801 1/2W
C6836
R6811 R6832 :FPRD CN6815

+10.5V
1.5 0.47 :RN R6858

R6809
220
LM393N Q6823 220k D6809 Q6816
R6900 R6805 :FPRD
# 100V R6814 27k 1P 1
DY-PROT 2PD601AR GND
+9V
+9V
6.8k 3W :MPS 2.2k :RN GP08D 2SD774-34 R6891

4.7k
18k C6817
:RN :RS :CHIP H-C MUTE PULS-RECT 8.8 12.3 135
47 DF 0N/OFF SW1 6.8k
134
:RN-CP 6.7 CN6617

8.8 :CHIP
O I R6887 0 1P
Q6800
R6885
R6810 R6813 C6883 G TAB

22k
1
C6850
2PD601A-Q-TX 1.8 1.8 1.4 0.2
10
:CHIP
R6806 R6847 0.1 R6889 R6890
V-SAW R6901 R6808 1/2W 1/2W Q6822 B:CHIP 150k 150k
Q6815
R6800 -0.2 3.9k :RN :RN 2.2k 0
18k 2SA1776TV2Q
+12V
# +9V 2SA1037AK :CHIP :CHIP 134

2
10k :CHIP R6888

14.0 :RN-CP IC6804 0.6 DF ON/OFF SW
2.3 H-C SHIFT R6879 C6844 47k 0
C6840 BA09T :CHIP
6.6 # 100 0.1
9V-REG
3
0.9 R6845 16V B:CHIP R6876

+12V
D6800 R6902 R6893 C6875

TH6801 0 # C6847 1.5 47
RD7.5ESB2 3.5 100k 0.1 +9V C6874 33k
R6848 11.7 14.6 R6892 16V 0
0.1 :CHIP
+9V
25V 100k
4
CLAP R6803 150k R6895

0.6
L -15V R6882 R6881 B:CHIP O I 100k :PT :CHIP Q6817

10k :CHIP C6877 R6894
30k 22k G :CHIP
:CHIP C6849 10 680k 2PD601A-Q-TX
5V :CHIP 0 3.0 INVER
R6877 R6878 C6880 D6826 0.1
B:CHIP
2.2k 330 0.1mF 1SS119-25 -0 B:CHIP

C6876 0
C6813 D6823 C6881 R6896 R6897
:RN-CP :RN-CP 25V 0.01
4.0 H-C MUTE 100k
C6815
0.001 1SS119-25 # C6839 C6843 IC6805 47k

:CHIP +135V +200V :CHIP B:CHIP
B:CHIP TEMP :CHIP 100 0.1 :CHIP 0 Q6818
BA12T
( )
R6815 R6883
C6871 Q6814 6.2k 10k 16V B:CHIP
12V-REG DTC144EKA-T146 POWER SUPPLY,
0.001
470p 2SA1037 R6886 :RN-CP :RN-CP

+9V
I O DF-PROT
JW6804
R6871 0 CH:CHIP H-SAW 4.7k

47k :RN-CP G VC
#
0 D6822
R6899
:RN-CP Q6813 C6872 10k # IC6806
.BLK058F C6869
DEFLECTION HV
-15V
1000p #
2PD601A-Q-TX :CHIP
#
CH:CHIP
H-SAW
C6870
#
R6898
JW(5MM)
+12V +9V
+9V
-15V
M +9V
B-SSS10133-HK.-D..-ES29
5V
-15V
+10.5V R6841
+6.5V D6825 1.8k
R6843 1W
5V DNA202K
10k :RS
:CHIP CN-PROT
+12V
D6814
RGP02-20EL-6394
G2 RECT
+12V +135V
10 9
8 C6882
11 .BLK0017 0.0047 .BLK04EB
4 7 2k
B
20
19
18
17
16
15
14
13
12
11
10
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
CN6802 CN6804
VM
VM
CN6810
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
NC
NC
NC
NC
NC
GND
.BLK05BA
.BLK03A2
.BLK03A3
.BLK058D
G2
SDA
H+
H+
SDA
V+
PROT
H1
PROT
HD1
HD2
9V
5V
SCL
HP2
VSAW+
FOCUS
FOCUS
SCL
VPROT
H-
H-
HP1
V-
H-SAW
12V
DEGAUSS
DF-SW
VFB2
VSAW-
N.C
N/S
ABL1
N/S
N
+12V
135V
135V
CN6800
X-RAY
200V
V SAW+
V COMP+
50P
H-CENT
-15V
6.5V
6.5V
M PIN
V SAW-
EX PARA
3P
V COMP-
1P
10.5V
10.5V
H LIN
AFC PULSE
EXTRA PARA
AFC PALSE
DF DRIVE
15V PALSE
20P CN6801 :BTOB :TAB :MICRO CONNECTOR

6P
TO A BOARD TO D1 BOARD TO C BOARD
TO DY TO C BOARD
CN1162 CN6100 CN9002
CN9007
5 6
O
H.DY H.DY V.DY V.DY
Schematic diagram Schematic diagram

? A board – 93 – D board / – 94 – – 95 – – 96 –

D BOARD IC6603 MCR5152 VD D BOARD WAVEFORMS – D Board (Conductor Side) –
I 18 VB
14 –
1 2
1 2 3 4 5 6 7 8 9 10 11 12 13
VC-1 + R U.V.
RESET DETECT
YC-2 11V S.V. 2 VG (H)
LEVEL R O
TSD 4.7
5V SHIFT PULSE R
+ START ~ ~ FILTER S O 0.7Vp-p (H) 28.8Vp-p (H) A
– UP 3 4
21V 19 VS
+
50K
10V VREL/VE–3
10V – LEVEL 15 VC-2
SHIFT
+ 5V 5V O
– PULSE 0.9Vp-p (H) 108Vp-p (H)
4V T CEN.
O 4.7 16 VC (L)
U.V.
DETECT
5 6 B
13V/BV
VREL/VE–2
LEVEL RELAY
SHIFT
21V 17
50K 2.4Vp-p (H) 222Vp-p
DELAY COM
7 8
R
C
S
5V
5K
52.4Vp-p (H) 6.7Vp-p (H)
13 9 10
–
OSC –
REFRESH + VOOP
5V + ON SHEET
20P
0V/3V D
+ 0.2V 50K 3.8Vp-p (H) 1.7Vp-p (H)
– –
11
+
2K
6 7 8 11 5 3 12 10
CT RT ROCP VOVP SS RESET COOP GND E
D [POWER SUPPLY, DEFLECTION HV]
7.8Vp-p (H)
– D Board (Component Side) –

1 2 3 4 5 6 7 8 9 10 11 12 13
F
G
B
H
C
I
D
J
E
D BOARD (Component Side) D BOARD (Conductor Side)

IC DIODE D6642 A-1 IC Q6807 D-2 D6617 G-12 D6807 B-7
D6643 F-5 Q6808 E-3 D6619 F-11 D6808 B-8
IC6601 J-2
D6601 J-8 D6644 C-4 IC6601 J-12 Q6809 C-4 D6620 F-13 D6809 D-4
F IC6602 J-2
D6605 I-4 D6645 G-5 IC6602 I-13 Q6810 D-5 D6621 G-11 D6812 D-5
IC6603 G-5
D6609 H-2 D6648 H-2 IC6603 F-8 Q6811 C-7 D6622 F-13 D6813 F-5
IC6604 E-1
D6612 H-5 D6650 F-1 IC6604 F-13 Q6812 H-6 D6624 G-10 D6814 F-4
IC6605 D-1
D6613 H-6 D6800 B-7 IC6605 D-13 Q6815 I-7 D6625 F-9 D6816 I-5
IC6606 C-1
D6614 H-2 D6801 A-7 IC6606 C-13 Q6816 J-3 D6626 F-10 D6817 H-5
IC6607 B-1
D6615 H-2 D6803 D-7 IC6607 B-13 Q6817 J-3 D6627 E-13 D6820 H-6
IC6800 C-7
D6616 G-3 D6805 E-7 IC6800 C-8 Q6818 J-3 D6628 E-12 D6821 I-6
IC6801 C-9
D6617 G-2 D6806 B-7 IC6801 B-5 Q6819 C-8 D6629 D-13 D6822 G-5
G IC6804 E-8
D6619 F-3 IC6804 E-6
D6807 B-7 Q6820 B-7 D6630 D-13 D6824 H-5
IC6805 E-6
D6620 F-1 D6809 D-10 IC6805 D-8 Q6821 C-7 D6631 B-10 D6825 B-3
IC6806 G-9
D6621 F-3 D6812 D-9 IC6806 F-5 Q6822 D-5 D6632 I-13 D6826 C-5
D6622 F-2 D6813 F-9 Q6825 C-5 D6634 E-11
TRANSISTOR D6623 G-2 D6814 F-11
TRANSISTOR D6635 C-13
D6624 G-4 D6816 I-9 DIODE D6636 A-8
Q6601 1-8 Q6601 J-6
D6625 F-6 D6817 H-9 D6637 A-13
H Q6602 G-2 Q6602 G-12 D6601 J-6
D6626 F-4 D6820 H-8 D6638 A-13
Q6603 H-2 Q6603 H-13 D6602 J-13
D6627 E-1 D6821 I-9 D6639 D-9
Q6604 H-1 Q6604 H-13 D6603 J-13
D6628 E-2 D6822 G-9 D6640 A-8
Q6606 H-1 Q6605 H-13 D6604 J-12
D6629 D-2 D6823 C-9 D6641 A-12
Q6607 D-2 Q6606 H-13 D6605 I-11
D6630 D-1 D6824 H-10 D6642 A-13
Q6608 B-1 Q6607 D-13 D6606 I-13
D6631 C-5 D6826 C-9 D6643 E-9
Q6609 A-2 Q6608 B-13 D6607 I-12
D6633 B-3 Q6805 B-12 D6644 C-11
Q6610 A-7 Q6611 C-12 D6608 I-13
I D6634 E-3 Q6806 C-12 D6645 H-9
Q6611 C-2 Q6612 C-13 D6609 H-12
D6635 C-1 Q6807 B-12 D6648 H-12
Q6612 C-1 Q6614 I-13 D6610 G-13
D6636 A-6 Q6808 E-11 D6649 G-13
Q6613 A-1 Q6800 B-7 D6611 G-13
D6637 A-2 Q6809 C-10 D6650 F-13
Q6801 E-7 Q6801 D-7 D6612 H-9
D6638 A-1 Q6810 D-10 D6800 B-7
Q6802 E-9 Q6802 E-4 D6613 H-9
D6639 D-5 Q6812 H-8 D6801 A-7
Q6803 D-8 Q6803 D-6 D6614 H-12
D6640 A-6 Q6814 I-1 D6803 D-7
Q6804 D-8 Q6804 D-6 D6615 H-12
D6641 A-3 Q6815 I-8 D6805 E-7
J Q6806 C-2 D6616 G-11
Q6816 I-11 D6806 B-7
– 97 – – 98 – – 99 – – 100 –

(3) Schematic Diagram of D1 Board
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
A
CN6104 CN6103
8P 3P
WHITE CN6102
BLK #
:S-MICRO
:S-MICRO
ROT+
QP(+)
ROT-
QP(-)
GND
135V
N.C.
N.C.
N.C.
CY+
CY-
NC
9V
TO VM BOARD TO RT COIL TO DY
8
3
.BLK04B7 .BLK02C7
B 3
4
135V
9V
9V
9V
C6352
#
6.5V IC6108 R6166 R6165

R6135
D6105 #
C 5V
MB88141APF-ER
DAC CONT RD2.7ESB2
DC SHIFT
10k
:CHIP
9V
R6163
#
2.9 0 R6164
#
M-PIN GND #
24
1
5.0 0
DF SW VSS1
23
2
0 5.0
DF PH VDD1
22
3
6.5V 2.2 4.4
9V
5V H-LIN SDA
21
4
5V 2.7 4.5
QP DV SCL
20
5
0 0 TO E BOARD
R6105 H-TRP MOD R6121
19
CN4800
6
4.7k R6119 R6120
IC6104 2.1 0 39k
:RN-CP 3.9k 10k
C6109 LA6500-EA QP PH CS2 3W
18
9V
D
7
5.0 :RN-CP :RN-CP
47 2.0 :RS CN6101
DQP-AMP 135V
QP AC CS1
17
10P
8
C6107 JW6157 1.8 5.0

R6106
# 5MM CS0 :S-MICRO
-15V
4.7k 9V
-15.3
5V CP CTR
16
0.8
9
1.7
1.7
69
:RN-CP R6171 0 5.0

470k C6105 IC6102 VDD2 5V
10
H-CENT
15
D6101 :CHIP 100 LM393N JW6158 D6111
1 2 3 4 5 2.2 0
D1NS4 25V DQP-CONT # VSS2 #
QP AV 10
11
14
PROT 1
DC CLAP 2.1 5.0
QP DC VCC 9 ABL1
12
13
1.7
4.3
1.6
C6101 0 R6127 R6128

9V
120k 220k C6118 1 2 3

R6101 10 C6102 8 5V
:RN-CP :RN-CP 47
100 50 2.2 4 3 2 1 C6129
:BP 16V R6129 C6128
:CHIP 50 9V 7
5V
2.2 0.01 10 6.5V GND
:BP
C6110 R6126 1W B:CHIP
#
R6123 4.7k 5V 6 HP1
:RS
E 9V R6108 R6133 D6103

1k
:RN-CP
:RN-CP
5 HP2
5V
8 7 6 5 10k 18k Q6103 DINL20U-TR
R6114 4 CP CNTL
4.3
:CHIP :RN-CP
10k 8.8 # DQP-SW IC6106
:RN-CP
2.1
3 -15V
5.0
2.6
2.7
IC6101 31.5 R6136 C6392

1k :CHIP
C6138
5 6 7 8 IC6105 1k Q6104 47 H-SIZE CONT
R6103
CXA1211M 100
1/2W 5.1 2SC2712-YG 25V 2 REF
QP-CONT C6108 C6136 LM393N
4.4
R6172 R6115 R6116 0.015 0 3.6 7.5 DQP-CONT INVERT

1
2.2
0.1
5.0
PROT 1
2.6
2.1
4.4
0 220k 22k 2.2k 0 31.4 630V

25V
:CHIP B:CHIP :RN-CP :CHIP 4 3 2 1 L6102 R6137 IC6356 D6404
R6117 5.1
1 2 3 4 1k 10mH 1k LA6510 DAN202K
:RN-CP :LHL13 0 :CHIP
N/S-OUT CLAP
.BLK04B3
135V
C6409
9V
3.4
4.7
C6133 R6442 R6140
5.0
8 7 6 5 15k
F R6109 R6118 0.47
2SC2712-YG
C6103 C6104 D6102 2.2k
10 15k :MPS + :CHIP
10k +
Q6105
:CHIP
AMP
R6102
5V
22 LM393N :RN-CP 4.4
5V
# 50 :CHIP 3.7 0
DC CLAP - - R6416
4.4
-15.4
:BP 4.4
11.7
-3.0
-3.0
IC6354
-3.5
-3.1
-3.4
-3.0
12k
-2.9
-2.8
CA0005AD C6381 0 :RN-CP 2.9

R6104 5 6 7 8 R6151
R6202 R6130 R6107 MALUTIPLAY 10 1k
4.7k R6203 .BLK04C7 .BLK0318
3.3k :CHIP 10k :CHIP 2.2k 9V 1 2 3 4 5 6 7 8 9 10
4.4
:CHIP 15 L6101 0 8.8 R6413 :CHIP

0 8.8 0
1.0
10k
0.9
3W 10mH :CHIP R6418

3.8 R6153 R6152
:RS :LHL16 470k .BLK0319 :RN-CP TO D BOARD
R6420 220k 22k
:CHIP 1 2 3 4 Q6405
390k R6178 :CHIP :CHIP CN6802
2SA1037AK 9V
-15V
Q6107 C6113 9V :CHIP 0.47 R6156
R6161 C6380 R6419 BUTT 2.6
2SB734 0.0047 R6169 R6149 R6143 1/4W Q6106 15k CN6100
R6113 10k 33k 56k 5.6k 0.068 100k
D6104 630V :CHIP
:FPRD C6385 2SA1037AK -3.0 :CHIP 50P
DQP-H MOJI 47k :RN-CP :RN-CP :RN-CP :RN-CP :MPS
1SS119-25 :PP 47 CONST.C :BTOB
:CHIP
12.3 R6176 R6433 C6386 C6388 25V
R6157 R6158 R6324
G 0.47 100k 47 10
47k 39k 47
R6124 1/4W :CHIP 25V
2.0
PS6101 R6438 R6139 :CHIP :CHIP :CHIP

D6110 12k :FPRD .BLK006D
.BLK0016
.BLK04C6
.BLK006F
C6114
2.2
4.7k 10k R6132 R6159

0.75A 10.5V :RN-CP R6148
ERA85-009 47
:CFK-I
:RN :RN-CP # 4.7k C6140
DQP-H CLAP2 D6106 #
12.0
D6108 1 1 PROT
R6206 DINS4 R6138 R6134 R6175 1SS119-25
R6204 220 R6167
PUMP-UP 4.7k 10k 27k TEMP.CORR 2 N.C.
2.2k :CHIP PROT # R6325
:4M :RN-CP :RN-CP :RN-CP
:CHIP -15V :CHIP 47
5V C6139 3 N.C.
:CHIP
1
C6350 R6359 4 135V
0.1 100k 9V D6355 9V
C6351 10.5V
25V 47 :CHIP DAN202K D6356 5 135V
B:CHIP R6357 #
C6355 CLAP 6
2.2k N.C.
100p
:CHIP
H 50V
CH:CHIP IC6351
D6357
# R6250 10.5V
7 N.C.
150k :RN
LM393N
-15V
# IC6250 R6274 8 SDA2

Q6350
R6378
DC-CONT R6375 R6255 #

#
#
2SC2712-YG 0 # C6254 R6160
5V
D6350 470
#
9 SCL
BUFF0.4 R6360 #
R6275
-15V
:CHIP R6385
5V
DAN202K 10k C6265
4 3 2 1 0 10 DF SW
CLAP :CHIP 0 0 # R6280 10.5V
:CHIP
#
R6386 C6207 R6278

Q6250
DGND V # 11 N.C.
18
100k
1
0 +
+ 0 C6365 R6263 C6208 47 # 1
#
R6259
:RN-CP # CIAMP
11.7
1.7 - 0.047 R6379 0 47 0

R6251 12 12V
25V
D6253
0 0
0 # SCL VSIN
17
C6366
2
R6256
#
B:CHIP :CHIP
+ # # R6264 Q6253 13 AFC PULSE
-
0 0
R6350 # #
47k SDL VSAW 14
16
IC6251 HP1
3
:CHIP C6362 9V 0 IC6353

R6361 C6356 R6262 0 C6266 #
0.0033 0 0 3.7 TA7805S
I
0.047 5 6 7 8 R6382 # # 10.5V 15 EX PARA
C6353 100k R6252 C6255 H
25V B:CHIP R6257 DVCC + 5V-REG
15
100p :CHIP 100k 9V # # CIAMP

B:CHIP :RN-CP # C6257 R6269 D6254 16 10.5V
CH:CHIP D6351 0 0 0 0 0 # 4.5 4.4 R6282
# - # 0
DAN202K REF R6205 #
HD 17 N/S
14
5V
5
7
-15.3
R6394 VOUT # 0 12.4 5.0

CLAP R6367 C6358 C6361
Q6251
12k 0.1 6.8k 0 0 R6270 4.2 0.3

0.1 9V Q6254 I O 18 10.5V
#
:RN-CP :CHIP HDY #

25V 25V REFV G
13
#
6
B:CHIP CON C6378

B:CHIP R6258 19 GND
0 .BLK0473
0 8.8 0.1
# 5.2 0
R6253 C6258 VDY R6271 C6376 0 C6377 B:CHIP
HSAW 20
12
-15V
7
R6362 R6326 # # CON # .BLK02C8

.BLK0475
.BLK0476 R6281 47 22
R6368 R6391 R6279 9V
# 12k 0 R6276 # 16V 25V -15V
15k 1k 0 # 21 GND
:RN-CP :RN-CP #
:CHIP HAGC HSTAT
11
R6261
C6250 C6253 R6260 22 5V
# #
# # 0 0
C6259
AVCC VSTAT 23 6.5V
10
#
J Q6356
2SC2712-YG 11.7
R6272
#
R6277
#
R6283
#
24 6.5V
DF.PRE DRIVE 6.5V 25 GND
R6265 R6267
# R6268 C6263 26 GND
R6254 #
# #
#
C6261 27 GND
Q6127 #
D6255
9V C6260 # 28
# 1.4
R6285 R6286 R6273 DF DRIVE
C6256 #
# # #
R6207 -15V # 29 FOCUS
3.3k Q6203 9V R6458 R6284
:RN-CP 2PD601AR 0 30 H LIN
47k #
ABL INV :CHIP R6110 1.3
D6210 0 R6287 31 VM
C6264
RD5.6ESB1 8.8 :CHIP #
K R6213
100k
R6456
100k
:CHIP Q6455
R6111
#
C6262
#
Q6252
#
32 GND
R6208 33 V SAW+
R6209 :CHIP 2SC2712-YG #
C6204 10k 120k 1.1 R6266
C6212 H PUL 2
0.01 C6202 :RN-CP :CHIP # 34 GND
0.1 0
B:CHIP 47
25V R6457 35 V COMP+
B:CHIP 22k
R6201 -15V R6219 R6459 36 15V PULSE
680 1k C6206 R6220 2.2k :CHIP
:RN-CP 47k C6216 R6227
1/2W 10 37 V SAW-
:RN-CP # 220
:FPRD R6218 :CHIP 9V
180k 38 GND
:RN-CP 9V C6106
V-SAW R6162 R6215 R6125 R6181
7 5 1.4 R6150 9V 0.047 39 V COMP-
1k 47k 2.2k 25V 220k
10k :CHIP :CHIP
L
:CHIP 8.8 :CHIP :CHIP 40
R6223 R6225 :RN-CP HP2
R6168
0 56k
14 13 12 11 10 9 8 8 7 6 5 :RN-CP
R6216 4.7k 41
:CHIP VFB2
D6201 4.7k R6214 :CHIP
:CHIP # 3.0 R6179 42 GND
RD5.6ESB1 C6201 IC6201 C6120
IC6202 C6209 C6116 150k 2
-5V-REF 47 CA0007AD C6215 R6177
:CHIP 0.047
# 470p 0.001 4.7k 43 GND
C6205 C6203 Q6128 R6112 25V
V SIZE COMP CH:CHIP CH:CHIP :CHIP 75k Q6108
0.01 47 LPF 2SC2712-YG 2SA1037AK
B:CHIP Q6125 44 H CENT
C6127
B:CHIP H-SAW 2SC2712-YG
0.01
B:CHIP H LIN AMP1 45 GND
1 2 3 4 5 6 7 1 2 3 4 46 H-SAW
R6141 R6174 R6200 C6122 0
R6210
2.2k :CHIP
R6145 R6212 47
100k 2.2k 22k 9V 470k R6147 9V 47 9V
4.7k 2.2k D6133
R6180
6 :RN-CP :CHIP :CHIP # R6196

8 :CHIP 1SS119-25 8.8 2.8
48 M PIN
M
0.47
R6154 H SAW-TEP R6144 :FPRD
1
R6221 C6112 R6190 8.8

R6224 3.9k 150k 49 ABL1
C6211 47k C6213 C6214 0.022 2.2k 0
10
56k C6115 1.3 1.8
:RN-CP # # :RN-CP B:CHIP :CHIP 1.4
R6217 R6211 470p IC6103 50 PROT
2
V-SAW R6226 0
220 C6131 10k 10k B:CHIP Q6126
:CHIP 3.4 LM393N
:CHIP 10 :CHIP 2SA1037AK
0 H.LIN R6122
50V -0.7 C6125
3
3.4 M.PIN CONP 1.5 R6192 H LIN AMP2

:CI 0.4 0 0 10
2.8 1.0
CH:CHIP
R6222 0 :CHIP 1.3

C6117
R6155 :CHIP
0.001
0 R6142 4.5
:RN-CP
47k R6170
4
10k
CH:CHIP
:CHIP
:RN-CP :RN-CP C6210 330 R6131
R6146
0.001 :CHIP 0 R6195

0 C6121 47k 10k
C6123
:CHIP 0
4.7
47k
Q6201 Q6202 Q6118

0.001
C6124 2SC2712-YG 2SC2712-YG 2SC2712-YG Q6124

N # H-SAW H-SAW H-SAW 2PD601AR
H-CIN MUTE
D6134
1SS119-25
H-L MUTE
R6173
100k
:CHIP
(DF, DQP DRIVE)
O
B-SSS10133-HK.-D1.-ES29
Schematic diagram
– 101 – D1 board / – 102 – – 103 – – 104 –

KV-ES29M90 KV-ES29M90
RM-916 RM-916
D1 BOARD WAVEFORMS
D1 [DF, DQP DRIVE] 1 2
– D1 Board –
80Vp-p (H) 0.5Vp-p
3 4
294Vp-p 8.8Vp-p
5 6
74Vp-p 6.6Vp-p
7 8
280Vp-p 8.5Vp-p
– 105 – – 106 –

KV-ES29M90 KV-ES29M90
RM-916 RM-916
C [CRT DRIVE] VM [VM DRIVE] F1 [AC LINE FILTER]

– C Board –
– VM Board –
– F1 Board –
– 107 – – 108 –

(4) Schematic Diagrams of C, F1 and VM Boards
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
CN9007
1P
G2
G4
1
B R9055 C9034
# CN1603
820k
1/2W
:RC
(AC LINE FILTER) 1P
JW1602 :TAB
JW1606
RV9002 # #
2.2M
1/2W
JW1601 JW1605 .BLK0012
.BLK0015
.BLK0016
.BLK0018
R9058 TO AC CORD #
NL9002 #
820k
1/2W # CN1601
FB1601
:RC 2P F1601
1.1UH
:VH T5A R1602
C 12V
320 L9001 1 200V
.BLK0187
250V VDR161
(ERZV14D621)
T1601
10MH
#
C9032 2
AC IN 1 1 AC OUT
R9089 G4 G2 R9056 C9031 :LHL08 NC T1602
22k 4700 680p R1601
# C9013 R9014 R9015 IC9001 J9001 3 5
1/2W 2kV 2kV 3 E AC IN 2 10MH 1M 2 AC OUT
:CHIP # # # Q9005 TDA6111Q/N4 RED.OUT 6 G1-1 0 C1602
3
:RC B B FB1602
:CHIP :CHIP :CHIP CV 0.68
# RED-VIDEO-OUT 4 H1 1.1UH
CN9005
1 7 H1 L9006 250V CN1602
3P RV9003 C9046 Q9003 Q9004 4 2P
R9016
WHT # # 0 11.6 11.6 8 H2 :LHL08 CN9002
# # # R9030 :VH
:S-MICRO 3P FB1603
155 (154)
136(135)
:CHIP #
13 9 D9010 WHT 1.1UH
2
G1-3 G1-2
TO A BOARD
200V
VOF
RV9001 TO F2 BOARD
D 12 10 L9007 MICRO CONNECTOR
12V
RD10ESB2
11.6
VO
199
VB
GND 1
VF
11 C9033
3.4
3.3
8.7
110M CN1116
IK
VI
3.2 0 0 #
E
KR KB BUFFER CN1651
0
22
12V
R9087 1/2W
11.6 R9073 KG
R 2 # 2.2k
3.3 3.0 154 159 154 250V TO D BOARD CN6804
:CHIP 1 2 3 4 5 6 7 8 9 R9047 CN1604
:CHIP 220 R1603
B 3 12V
1/2W
R9061 1P # C1601
R9049 R9050 D9009 100 L9005 JW1603
R9048 C9008 :TAB
R9088 2.2k R :RC 3.9k H ST 1 GP08D 1/2W FB1604 # 0.47
R9091 2.2k 4p R
# :CHIP 2 :RC :LHL10 1.1UH 250V
# :CHIP :CHIP CH:CHIP C9019 C9012 PROTECTOR
0.047 R 0.047 3 R9057
:CHIP Q9009 GND C1603 JW1607
3.8
250V 560k JW1604

2SA1037AK-T146-R F:CHIP R9040 R9059 #
1/2W #
E JW(5) NL9003
1k 4700p JW1608
5 R DRIVE L9002 # C9004 :RC
1/2W 250V #
R DRV 1 R9036 C9028
0.0047 :RC .BLK0040
.BLK002F
.BLK0006
.BLK0030
.BLK0033
.BLK0042
.BLK0043
.BLK0041
R9086 :EL0606 2kV
E E 2
6
#
:CHIP
R9070
330
:CHIP
0
3.2
0
(3.9) 1k :CHIP 0.0047 B:CHIP
D9006
G
B-SSS10133-HK.-F1.-ES29
G DRV 3
R9071 HSS83TD
3.0 B
330 R9072 0 R9031
E 4 PROTECT
7 :CHIP 330 2k R9037
0
:CHIP 3.3 :RN-CP 0
B DRV 5 C9022
0.01
12V C9018
E 6 F C9005
R9001 C9015 R9035 10
3.7 2.7k 4p 12V 2.2k 4p
Q9010 250V
12V 7
R9020 2SA1037AK-T146-R Q9011 :CHIP CH:CHIP :RN-CP CH:CHIP
:HT
# 2SA1037AK-T146-R IC9002 CN9003
IK 8 G DRIVE
:CHIP B DRIVE TDA6111Q/N4 1P
F E 9 GREEN-VIDEO-OUT
GREEN.OUT
:TAB
C BOARD WAVEFORMS
TO COATING EARTH
R9021
CN9001 0
9P
BLK
:CHIP 1 PAL 1 SECAM/NTSC 2 3 4
:S-MICRO R9022
# 1 E
200V
VOF
VB
:CHIP
12V
11.6
VO
130
VB
199
VF
131
160
3.4
3.3
8.6
IK
VI
TO E BOARD 0
R9051 R9053
CN4500 R9023 220 3.9k
0 1 2 3 4 5 6 7 8 9 1/2W
:CHIP :RC
E
118Vp-p (H) 118Vp-p (H) 117Vp-p (H) 123Vp-p (H) 23.2Vp-p (H)
G G
CN9006
250V
12V # 5 6 7
C9011
R9026 R9045 L9003

2k JW(5) :TAB
:RN-CP G :EL0606
0.047
C9029
R9041 0.0047 D9007 1 E
C9006 1k B:CHIP HSS83TD
4p :CHIP
CH:CHIP
PROTECT
C9021
10 4.5Vp-p (H) 4.4Vp-p (H) 4.4Vp-p (H)
250V C9026 R9038
R9018 C9009 :HT 0.047 2.2k R9043
2.7k
H :CHIP
4p
CH:CHIP
F:CHIP :RN-CP 0
CN9004
C9003
1P
4p
:TAB CH:CHIP
12V
TO COATING
EARTH BLUE.OUT
NL9001
E 1
I R9019 D9005
:L
PICTURE TUBE
L5400
2.7k C9007 MA111-(K8).SO C5417
R9007 12V
:LHL08 #
200V
4(142)
:CHIP 4p IC9003
VOF
2k
12V
11.6
VO
143
199
VB
VF
155
3.3
3.4
8.7
CH:CHIP C9025 TDA6111Q/N4

IK
VI
:RN-CP
E
0
R9033 220 BLUE-VIDEO-OUT M68LNH070X
12k 16V C9016 R5415
C9010 :RN-CP :HT 1 2 3 4 5 6 7 8 9 #
Q5403
4p R9069 100 C5413
100 R5403 Q5402 2SC3311A-QRSTA 1/2W 100 C5414
E
CH:CHIP R9046 R5413

1/2W 100 R5404 8.8 BUFFER 160V #
R9034 C5401 2SC3311A-QRSTA 560 :FPRD
+12V
C9023 JW(5)
250V
5.6k C9027 :RC C5400 470 1/2W 820

0.01 BUFFER :FPRD
C9014
:RN-CP 0.01 R9052 # :FPRD

F F 220 16V R5401
C9030 8.9
J 1/2W R9054 2.2k R5416
5.9
12V 0.0047
0.047
:RC 3.9k 5.5 2.2

R9042 B B:CHIP C5418
1k R5425 C5407 Q5406 :FPRD
D5401 33
B 0.01 2SA2005
5.8
:CHIP 47 160V
R9006 D1NS4-TR 200V 0.9
10k C9042 D9008 VM-OUT
330 C5402 VOLTAGE DROP :PT
:CHIP R9044 HSS83TD L9004 5.7
25V 0.47
R9065 0 PROTECT R5400
:PT D5402
6.8k :EL0606 # R5424
135V
:CHIP R9068 ISS133T 1.3

C9024 15 0.7
R9013 150k C9020
:CHIP 0.047 VOLTAGE DROP 1 QP-
4.4 1k 10 C5419 R5410 R5414
:CHIP F:CHIP R5426
Q9001 0 250V # # 47 18k
:HT
D5403 2 N.C.
2SA1037AK-T146-R R5412
K BUFFER
D9002 R9039
2.2k
C9002
4pF (CRT DRIVE) C5403
470
1SS133T
VOLTAGE DROP 10k
D5405
3 QP+
8.1 MA3091 :RN-CP CH:CHIP 6.3V MTZJ-T-77-22 C5410 JW5402
R9008 C5406 4 QP+
PROTECT LEV.SHIFT 0.001 5MM
33k 470 :PT C5415
:CHIP 6.3V 5 GND
0.1
R9012 D5404 200V
1k R5411 R5419 FB5400
:PT 6 GND
:CHIP
1SS133T 47 5.7 2.2k #
11
VOLTAGE DROP 5.5 7 VM
VM
C5409 R5423 FB5401
GND 10 C5420 5.5 2.2 # 8 VM
JW5400 0 470 C5416
JW5407
L 9V/12V 9 #
R5405
# #
5.0
250V R5420
2.2k
3W
:RS
#
CN5401
JW(5MM) 8P
2SA1309A-QRSTA
B-SSS10133-HK.-C..-ES29 9V 8 JW5406
0 C5411
5MM :BTOB
D5406 0.001
7
Q5405
GND 8.0 2.0 Q5404 MTZJ-T-77-22 :PT
1.9 2SA1309A-QRSTA
TO NECK ASSY
N.C. 6 5.0 LEV.SHIFT
BUFFER Q5407
R5417
QP(-) 5 C5408 2SC5511
R5406 0.01 18k
4.7k 1.2 Q5401 VM-OUT 57
4 200V
N.C. R5428 2SC3311A-QRSTA
1.4
Q5400 :PT 133.9

#
M QP(+) 3
D5400
2SC3311A-QRSTA
VM AMP
VM AMP
R5427
2 C5404 134.4
N.C. 1SS133T R5407 # R5409 15
R5418
TEMP-CORR 33 220 560 R5421
135V 1 2.2
C5405 :FPRD
100
CN5402 16V
11P R5402 R5408 C5412 R5422
WHT 680 100 470 100
:S-MICRO 16V :FPRD
N
(Pin 1-7)
TO D1 BOARD
CN6104
(Pin 8-11)
(VM DRIVE)
TO E BOARD
O CN4502
B-SSS10133-HK.-VM.-ES29
– 109 – – 110 – – 111 – – 112 –

(5) Schematic Diagram of E Board
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
A
L4312
#
:CHIP
+12V +12V
L4310 1 9V/12V
C4335 C4337
100 0.01
:CHIP 16V B:CHIP 2 GND
+12V +12V .BLK03E4 3 VM
+12V D4311 CN4502
DAN202K 3P
B R4338
470 C4339
C4316
47
L4301
R4313
4.7k
:CHIP
4.6
0
WHT
:S-MICRO
C4333 L4302 L4305 :CHIP 22p 0 25V :CHIP D4313
0.1 CH:CHIP MA3062M-TX 2.8 0 TO VM BOARD
C4334 25V :CHIP :CHIP Q4319
R4343 Q4304 C4324 0 CN5402
47 B:CHIP
100 2SA1037K 0 0.1 Q4316
R4352 2SC2712-YG 25V 2SC2712
:CHIP 0 8.9
470 B:CHIP R4314
:CHIP 0 2.2k 0
R4345 C4381 :CHIP FB4387
R4387
12k # R4339 R4353 R4373 Q4317 0
R/G/B(OSD) 7.0 1.2k 0
:CHIP :CHIP 1.2k 0 DTC114EKA :CHIP :CHIP
L4311 C4341 :CHIP :CHIP :CHIP R
+12V
R,G,B,BLK 10p 1 R 0UT

FB4388
R/G/B (TELETEXT) +12V
BLK
R
:CHIP CH:CHIP R4388
B
0
R4349 2 GND
C
0
GT
:CHIP
RT
BT
R(OSD)
B(OSD)
G(OSD)
470 G :CHIP
BLKT
:CHIP 3 G OUT
B(TEXT)
GT
RT
BT
G(TEXT)
R4389 FB4389
BLKT
R4346
R(TEXT)
18k D4312 0 0 4 GND
1 16V F:CHIP
1 16V F:CHIP
1 16V F:CHIP
:RN-CP DAN202K B :CHIP :CHIP
R4371 L4308 5 B OUT
R4340
0 :CHIP
R4398 #
25V B:CHIP
R4395
0 :CHIP
25V B:CHIP
# :CHIP +12V 6
25V B:CHIP
GND
47
25V B:CHIP
100 R4396
C4331 9V
:CHIP C4329 0.47 0 7 +12V
C4328
C4327
C4345
TO A BOARD :CHIP
C4326
4.7
C4343
C4363 C4365
8 IK
CN1401 9V 47 #
R4397
C4346
C4349
C4348
L4309
CN4101 9 GND
0.1
0.1
:CHIP C4364
0.1
40P
0.1
0 C4352 47
:BTOB 47 CN4500
D C4317
13 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33
C4369 R4372
9P
NC
1 BLK
GND
VCC
EXTRA PARABOLA
VCC
BPH 0.1
VM_MOD
YSYM1
0 0 L4306
VM_OUT
0.1 0 0 0 0
YS/YM2
R4309
CLP_C
1k
G1IN
G2_IN
B2_IN
HS
R2_IN
R1_IN
4.7
B1_IN
4.7
25V
4.7
4.7
4.7
:S-MICRO
4.7
3.9
8.9
6.3
VM/SHC_OFF
5.5
8.9
8.9
DPIC_DCTR
25V
IREF_SIG
C4355 :CHIP #
H DEFL 2 B:CHIP :CHIP B:CHIP
0 8.9 0.1 25V B:CHIP
AFC PULSE TO C BOARD
3 52 Y1IN VCC 32 C4310
5.8
2.9
C4318 0.1 25V B:CHIP 3.7 C4312 R4375
C4356 R4365 #
# 1k R4311 CN9001
HD1 4 53 CB1IN R_SH 31 :CHIP
5.8 4 2.5 0.1 25V B:CHIP 100 :CHIP 0 :CHIP :CHIP #
C4319 0.1 25V B:CHIP 14 R
FPD 5 54 CR1IN R_OUT 30
2.9
0 5
4.0 C4357 R4366 R4308 R4377
6 55 FS 15 29 C4314
D FOCUS C4320 0.1 25V B:CHIP G_SH 0.1 25V B:CHIP 100 :CHIP 0
0 1k R4315
G :CHIP 0 #
2.7 :CHIP :CHIP #
+12V 7 56 Y2IN G_OUT 28
C4321 IC4301
5.8 3.5 6 R4310 0
0.1 25V B:CHIP C4358 R4367 Q4307
V SAW + 8 D4309 57 CB2IN CXA2100AQ 27 0
E HD2 9
#
0.1
C4322
25V B:CHIP
0
58 CR2IN
Y/C/J
B_SH
2.4
B_OUT 26
C4353 0.47 16V
0.1 25V
B:CHIP
B:CHIP
B 100 :CHIP 2SA1037 :CHIP 0
R4312
0
Q4310
R4384 100 :CHIP 5.8 5.0 Q4308 2SA1037
V SAW - 10 D4308 59 HS_IN IKIN 25 0
# VS R4301 100 :CHIP
2SA1037 :CHIP 0
0.3 0 C4354 R4363
GND 11 60 VS_IN PABL_FIL 24
0.47 16V B:CHIP 100
R4335 100 :CHIP 0 7.6 :CHIP JR4301
V DEFL 12 61 SDA ABL_FIL 23 0
R4336 100 :CHIP C4311 C4313 C4315
R100 R4361 3.3M :CHIP
4.4 1.6 C4359 :CHIP # # #
R100 13 62 SCL ABL_IN 22
6.0 0.0022 :CHIP :CHIP :CHIP
R4337 100 :CHIP
4.4 B:CHIP
VPROT 14 63 EXTRA_PARA 3 RGB_AFC 21
1 0
2
VTIM/TEST
V_PROT1
15 64 DF_PARA 20
VCC(H.V)
ABL-CTR XRAY R4383
AFC_FIL
C4518
V_AGC
D4305
V_OSC
IREF_J
R4518 18k
L2_FIL
3.5
HP_IN
R4519
XRAY 16 # :CHIP
500K
100
GND
DTZ9.1
REG
GND
SCP
VDP
VDN
100
F
7.6
3.3
3.4
3.8
2.6
EW
3.4
5.0
2.5
NC
HD
16V
8.9
B100
4.4
:CHIP 0.9
4.8
1.7
4.2
B100 17 F:CHIP 0 0 0 0 0 :CHIP PROTECTOR
C4366
.BLK03E5 C4301 R4381 0.01mF
R4357 L4307
GND 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 0.1mF 2.2M B:CHIP
R4303 100 :CHIP R4507 10k #
G 25V
47
#
GREEN 19 470 :CHIP
B:CHIP
:CHIP R4344 R4354

R4302 100 :CHIP R C4330
503.5KHz
10k C4367
C4336
100 C4351
RED 20 0.1 :RN-CP
R4893 :CHIP 0.001 0.047
R4305 100 :CHIP B :PP
# B:CHIP B:CHIP
BLUE 21
R4351 22k :CHIP
:CHIP
0.01
R4304 100 :CHIP BLK D4813 R4319 C4332 C4350

22 R4348
47
BLK
R4359
R4318
:CHIP
X4300
8.2k 0.047 0.1 25V B:CHIP

220k :CHIP
DAN202K 8.2k
100 C4338
R4317 :RN-CP :MPS
C4342
TEXT RED 23 CN PROT :CHIP 0.1

R4401
:RN-CP C4379
C4340
22k
R4520 C4325 25V #
#
:CHIP
100
GND 24 100 10p B:CHIP CH:CHIP

8.2k :CHIP
#
R4320
0 :CHIP
#
:CHIP
R4362
:CHIP
G
2.2k R4321
C4377 #
R4358
25
R4342
TEXT GREEN Q4303 :RN-CP 2.2 D4301 C4360 R4368

R4347
C4361
R4521 100 :CHIP :CHIP # 4.7 R4364 #
GND 26 2SC1623-L5L6
#
R4306 100 :CHIP AGC CONT
R4341
9V
TEXT BLUE 27 1.5
:CHIP
R4307 C4344
28 L4303 0.047 0
GND 100 Q4305 R4316 D4304
25V
:CHIP R4380 # DTZ9.1
DTC144EKA-T146
R4350 :CHIP B:CHIP 6.8k
TEXT BLK 29 10k :CHIP
2.2k
PROT SW
100 CLAP
:CHIP :CHIP Q4315
GND 30
L4304 0
R4360
C4309 R4370
SCL2 31 R4382 Q4306 1k
C4378 :CHIP 0.22
10k :CHIP
9V
9V
100p # 16V
SDA2 32 CH:CHIP :CHIP D4302 B:CHIP
C4347 #
H 9V 33
34
0.1 25V B:CHIP
C4362
0.01
9V
SCP 50V
R4504 R4334 R4355 R4356 R4322
C4371 C4370 R4403 B:CHIP
GND 35 # 1k 1k 1k R4376
0.1 25V B:CHIP 47 Y100 R4402 C4380 # #
:CHIP :CHIP :CHIP :CHIP 100
# # :CHIP
Y100 36 :CHIP B:CHIP
:CHIP R4323
U100 Q4320 22k
R4331 R4405
U100 37 100 2SA1037AK :RN-CP
0 #
9V :CHIP BUFFER :CHIP
38 9V 0
GND 9V
V100 R4505 Q4318
V100 39 # :CHIP # R4406 R4369 R4374
R4407
AFC CORE # # 100 100
DPIC SW 40 0 R4404
:CHIP :CHIP
Q4321 :CHIP :CHIP
R4332 #
100 2SA1037AK :CHIP
I :CHIP BUFFER
-15V
R100
B100
R4333
Q4820 R4506 100
2SC2712-YG R4411 # :CHIP :CHIP
10k
R4410 C4834
2.2k 100mF Q4322
R4408 2SA1037AK
100 BUFFER D4814
C4833
R4409 10mF R4412
D4816 DAN202K
J 10k 100k 1SS119-25 CN PROT
Q4821 Q4822
R4884
DTC144EKA-T146 2SC2712-YG 47k
:RN-CP R4894 R4895
10k 10k
:CHIP :CHIP
R4805 C4813
D4805
2.7k 0.01 R4326
C4814
E/W BUFF
H SIZE SAFT
#
2SA1037
C4803 C4804
2.2k :CHIP
2SC2712
47
B:CHIP 68k
Q4813
R4800 :RN-CP R4856

Q4803
0.01 47 R4808 :RN-CP

2.2k C4828 2.2k
R4861
:CHIP B:CHIP 9 #
# IC4802 :CHIP R4862
Q4801 R4814 :CHIP
:CHIP C4805
K C4827
#
C4801
2SC1623
H DRIVE2 D4800
10
0
100k NJM3404AD
PLL AMP
R4831
3.3k
2.3
R4857
4.7k R4858
10k
2.2
R4863
#
:CHIP
D4806
#
R4330
47k
Q4301
:CHIP R4803 8.9 R4816 R4832 R4836 # 0 :CHIP
0.1
1k
DAN202K
:MPS
10k 47k 47k Q4810 0 D4807 2SC2712-YG
DISV-SHARGE
2.2
:CHIP 3.2 :CHIP :RN-CP :RN-CP 2SC2712 R4838 DAN202K R4881 R4327 ABL CONT 1
C4800 R4801 0 100k 47k
H PULS 0
1.6
0.1 R4864 BIAS

1
1k :RN-CP :RN-CP
4.2
R4813 11 0.7 :CHIP R4329

:MPS :CHIP R4859 0.7 1.8k 1k
0 C4802 47k C4806
4.4
2SA1037
R4804 :CHIP 4.7k :RN-CP R4324

Q4814
470p
BIAS
0.001 C4824 R4865

2
10k CH:CHIP C4815 0 4.7k

:CHIP CH:CHIP R4839 0 0 0.047 470 :RN-CP
0 R4817 #
R4802 10 0.3 8.2k C4823
R4860 B:CHIP
0.2 8.9 560k 1.4 C4308
R4815 100k :CHIP 0.0047 R4866
3
10k 330 1
Q4800 B:CHIP 47k
1
:CHIP 12 R4837 R4841 R4840 R4325

2SC2712 47k 0 Q4815 :CHIP Q4302
4.4 2.2k 0 0 33k
2.2k :CHIP
H DRIVE1 0.3 R4822 R4820 :RN-CP 2SA1037 GATE1 2SA1037AK

4
R4821 :CHIP :CHIP :RN-CP

2.2k 10k 0
R4819
ABL CONT 2
L
2
10k D4808 R4328

:CHIP :CHIP R4833 D4303
4.3 3.2 :CHIP 47k R4842 #
R4818 Q4811 R4887 # :CHIP DAN202K RD3.9ESB2
2.2k
C4816 :RN-CP 47k Q4812 :CHIP
0 2SC2712 H.PULS PROTECT
3
C4807
22pF :RN-CP 2SA1037 CLIP
4.2 :CHIP 0
0 R4827 GATE2 D4815
-15V
IC4800 #
Q4805
C4830 R4845
D4812 R4877
R4834 0 0 :CHIP # :CHIP 100k :RN-CP # 2.2k
LM393N
4
2SC2712 2.2k 1SS119 :CHIP

FF CONP2 C4817 D4811
0 FF1 :RN-CP 47 0 D4802
E/W ABL3 D4809
4.3 RD2.2ESB2 R4888 R4879
RD4.7ESB2 R4844 DAN202K # 220k
E/W ABL2
R4843 5.6k E/W ABL1 :CHIP :CHIP
R4899
R4882
:CHIP
2.2k R4898 R4897 R4880 0.7

Q4804 R4835
:CHIP #
2.2k :CHIP :CHIP # R4846
2SC2712 :CHIP
:RN-CP 3.3k R4867 C4825
FF2 R4869
0 7.7 0.047
0.8
# 22k
R4883 0
25V R4878
0.2 R4826 :CHIP :RN-CP 0
0.8
R4823 R4825 # 150k

C4829 R4806 8.7 2.2k R4890 B:CHIP -15V
M 2.2k R4824 10k

:CHIP R4828 4 3 2 1 :CHIP
# :CHIP
# 2.7k :CHIP R4829 D4801 # R4868

R4870
:CHIP 10k 2.2k Q4816

1
:CHIP :RN-CP 4.4 2.2k #

C4811 :CHIP :CHIP DAN202K 5V 2SA1037 H.CONP C4831 # :CHIP
0.3 :CHIP
0.01 0.2 PROTECT
C4808 0
IC4803
2
0.1 B:CHIP C4812 4.2

1.6 4.4 3.1
:MPS 4.4 47 R4896 C4826 R4876
3.2
CPC-AMP # # #
3
0 0 :CHIP R4871 R4872 R4886 :CHIP :CHIP

22k
R4807 0.3 R4885

# 2.2k 68k
0 4.4 #
1k :CHIP
R4850 Q4817
3.1
H PRE DRIVE2
CH:CHIP
:CHIP Q4807 5 6 7 8 :CHIP

4
5
C4809
R4810
C4818 100k 2SC2712 PIN BUFF2

0.001
2SA1037
Q4806 2SC2712
Q4809
0 2.2mF :CHIP
R4809 2SC2712 FF1 0.8 8.9
3.5
FF2 C4832
0.8
10k R4874
R4892 # 0
:CHIP 0 R4849 R4851 R4873
0 2.0 1.5k :CHIP
3.3k #
R4855
N
C4820 D4803
0 4.7k
R4811 C4819 47 1SS119-25 CPC1
Q4802
2SC2712
22k
:RN-CP
IC4801
LM393N
#
R4848
Q4818 R4875
2.2k
(RGB OUT,DEFLECTION)
C4810 2SA1037
INVER H DRIVE # Q4808 10k C4821 C4822 :CHIP
FF CONP1 0 R4853 R4854 PIN BUFF1
2SA1037 :CHIP 47 1.5k 47 -15V
5.6k
R4812 H PRE DRIVE1 16V R4852 :CHIP 16V
0 R4847 22k
:CHIP
7 8
10k
:CHIP D4804
1SS119-25 CPC2
10
1
GND
5V
CN4800
HP1
CPCP
REF
HP2
PROR 1
B-SSS10133-HK.E..-ES29
ABL 1
-15V
PROT 1
10P
O WHT
CONNECTOR ASSY
TO D1 BOARD
CN6101
Schematic diagrams Schematic diagram

? C F1 VM boards – 113 – E board / – 114 – – 115 – – 116 –

KV-ES29M90 KV-ES29M90 KV-ES29M90
RM-916 RM-916 RM-916
E [RGB OUT, DEFLECTION]
E Board IC4301 CXA2100AQ

– E Board (Component Side) – – E Board (Conductor Side) –
1 2 3 4 5 1 2 3 4 5
DPIC-DCTR
VMC-OFF
VM-MOD
VM-OUT
YSYM1
YSYM2
CLP-C
G1-IN
G2-IN
R1-IN
R2-IN
B1-IN
B2-IN
BPH
A A 46 45 44 48 43 50 41 40 39 38 36 35 34 33
• R-CUTOFF
• G-CUTOFF
• B-CUTOFF
VM • LRGB2-LEV • BLK-BOTTOM
• PIC-ON
• VM-LEVEL SHP • R-ON
0~-9dB
• SHARPNESS LTI • G-ON
B B • PRE/OVER • PICTURE • GAMMA • B-ON
• LTI-LEVEL • DPIC-LEVEL • SUB-CON • D-COL • R-DRIVE
• SHP-F0 • AGING W • BRIGHT • DCOL-TEMP • G-DRIVE
• AGING B • SUB-BRIGHT • LIMIT-LEV • B-DRIVE 24 PABL-FIL
Y1-IN 52 Y Y Y R 30 R-OUT
YCbCr SW CLP DPIC
Cb1-IN 53 CLP 28 G-OUT
Cr1-IN 54 • DL-PASS • DC-TRAN R-Y GAM AKB 26
G-Y MAT G YS PIC YS B-OUT
FS 55 SW DCOL DRV BLK
B-Y YM BRT YM 31 R-SH
C C Y2-IN 56 COL
LIMT PABL
29 G-SH
YCbCr SW AXIS B
Cb2-IN 57 CLP
Cb/Cr HUE 27 B-SH
Cr2-IN 58 • COLOR
• COLOR-AXIS 25 IK-IN
• HUE
• NTSC-JPN
CTI • CB-OFFSET1 22 ABL-IN
• NTSC-US
• CR-OFFSET1 ABL
SCL 62 CLP PULSE • PAL 23 ABL-FIL
I2C BUS • CTI-LEVEL • CB-OFFSET2
BLK PULSE • OTH
DECORDER • CR-OFFSET2 • ABL-MODE
D D SDA 61
• ABL-TH
16/HVCO • H-LOCK • P-ABL
HS-IN 59 21 PGB-AFC-OUT
500K 15 AFC 19 L2-FIL
AFC-FIL 14 1/16 DIV 18 HP-IN
20 XRAY-IN
LOOP2 HD 17 HD-OUT
E E PULSE 16 VPROT
SCP-OUT 13 SCP
GEN • H-POSITION
• AFC-BOW
• LEFT-BLK • AFC-ANGLE V-FUNC 5 VDP-OUT
• :Pattern from the side which enables seeing. • RIGHT-BLK • V-SIZE • V-LINEARITY 6 VDN-OUT
VTIM-OUT 10
• :Pattern from the rear side. • V-POSITION • V-COMP
E BOARD WAVEFORMS • S-CORRECTION • V-ON
W-FUNC EW-FUNC 1 EW-OUT
E BOARD (Component Side) E BOARD (Conductor Side) 1 2 3 4 5 VS-IN 60 COUNT AGC
VOSC • V-SCROLL • H-SIZE • LO-CORNERPIN • EW-DC
IC Q4320 D-1 DIODE IC Q4806 B-12 D4806 A-1 • V-FREERUN • PIN-AMP • TRAPEZIUM • H-COMP
• V-ASPECT
Q4321 D-1 Q4809 B-1 D4807 A-2 • AKB-TIM1 • UP-VLIN • UP-CORNERPIN
IC4301 C-2 Q4322 D-2 D4302 A-2 IC4800 B-2 Q4812 A-1 D4808 B-1 • AKB-TIM2 • LO-VLIN DF-FUNC 64 DF-PARA
IC4800 A-4 Q4800 B-4 D4303 B-3 IC4801 C-2 Q4814 A-1 D4809 A-3 • VBLKW • U-SCAN
IC4801 C-4 Q4804 D4304 B-3 IC4802 B-1 1.5Vp-p (V) 1.4Vp-p (V) 5.0Vp-p (V) 2.4Vp-p 2.4Vp-p • ZOOM-SW
B-5 D4811 A-3 IREF REG 63 EXTRA-PARA
IC4802 B-5 Q4805 B-4 D4305 B-12 IC4803 C-2 DIODE D4812 A-2 6 7 8 9 10
EXTRA
IC4803 D-4 Q4806 B-2 D4308 D-3 D4813 B-4 • M-PIN
Q4807 C-5 D4309 D-3 TRANSISTOR D4301 C-3 D4814 B-3
TRANSISTOR Q4808 D4303 B-3 49 11 7 3 4
B-4 D4802 B-5
Q4301 A-3 D4311 B-5 D4815 A-2
IREF-J
REF
V-OSC
V-AGC
IREF-SIG
D4805 B-4
Q4303 D-4 Q4810 B-5 Q4302 B-3 D4312 B-5 D4819 C-3
D4806 C-5
Q4304 C-1 Q4811 B-5 2.4Vp-p (H) 7.3Vp-p (V) 64.0Vp-p (V) 1.7Vp-p (V) 1.2Vp-p (V)
Q4315 C-3 D4313 A-4
D4811 A-3
Q4305 A-2 Q4813 A-4 Q4316 B-4 D4800 B-1 11 12 13 14 15
D4812 A-4
Q4307 B-2 Q4815 B-5 Q4317 B-4 D4801 C-1
D4815 A-4
Q4308 B-2 Q4816 A-3 Q4318 D-3 D4802 B-1
Q4310 B-2 Q4817 A-5 Q4801 B-2 D4803 C-1
Q4319 C-1 Q4818 A-5 Q4802 B-2 D4804 C-1
2.7Vp-p (V) 2.1Vp-p (V) 0.1Vp-p (H) 0.7Vp-p (H) 0.6Vp-p (H)
Schematic diagrams
– 117 – – 118 – – 68 – – 119 – H1 H2 H3 boards /

(6) Schematic Diagrams of H1, H2 and H3 Boards
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
A CN1901
STBY+5V
TO A BOARD
5P
SIRCS
CN1190
LED 2
LED 1
WHT
GND
:S-MICRO
TO A BOARD
1
TO A BOARD CN1932 CN1195 CN1934
6P
& 12P
HP MUTE
WHT
PULL UP
CN1193
HP GND
AU GND
HP R IN
RED
HP L IN
:S-MICRO
B TO J BOARD
KEY 2
CV IN
:S-MICRO
GND
GND
GND
GND
GND
R IN
C IN
Y IN
S IN
L IN
CN8301
10
11
12
1
R1911 R1913 R1914 R1915

330 10k 330 10k R1916 C1910
R 47 47
Q1901 Q1902 16V R1917
L DTC144ESA DTC144ESA C1911 100
LED DRIVER LED DRIVER 47
C 16V
PROTECTOR
D1943
R1920 R1921
#
D1942 100 100

#
PROTECTOR D1930
RD9.1ESL2 G R
1
PROTECTOR
PROTECTOR D1906 IC1901

D1940 C1912
SPB-26MVWF SBX1981-51(21) 470p
D1941
# LED(2COLOUR LED)
3
REMOTE SENSOR
#
JW1933
PROTECTOR
D #
R1952 D1934
2.2k # D1935
RD9.1ESL2
PROTECTOR
D1931
#
D1932
# R1934
(LED,SIRCS RECEIVER)
PROTECTOR 100
D1933
# B-SSS10133-HK.-H1.-ES29
E D1937 PROTECTOR
R1948 #
JW(5) D1938
#
R1949 PROTECTOR D1939
JW(5) R1953 R1935
JW(5) 100 #
R1950
PROTECTOR CN1980
JW(5) 3P
R1951 WHT-L
KEY 1 OUT
JW(5) :S-MICRO
F L1932 C1930 R1932 R1947
TO A BOARD
GND
0.01 # #
NC
:EL0606 :MPS CN1190

C1935 R1933 R1936 C1938
470p 470k 470k 470p
L1931 R1954
1
C1932 1 2 3
#
0.01
:EL0606 :MPS
JW1934 C1970 1 2
G #
AUDIO RIGHT #
:CHIP
AUDIO LEFT
1 2
R1970 R1971 R1972 R1973 R1974 R1975 R1976
820 1k 1.2k 1.8k 3.3k 6.8k 18k
3 4
R
V
1 2 1 2 1 2 1 2 1 2 1 2 1 2
J1932 S1931
TERMINAL,S AUTO PRESET
2 2 2 2 2 2 2 2
H J1931
JACK
J1933
JACK,3P
1 1 1 1 1 1 1 1
S1972 S1973 S1974 S1975 S1976 S1977 S1978 S1979

(AV INPUT,PRESET KEY,PHONE OUT) STBY PRG+ PRG- VOL+ VOL- TV/VIDEO ENTER MENU
I B-SSS10133-HK.-H2.-ES29
(TOP KEY)
B-SSS10133-HK.-H3.-ES29
– 120 – – 121 – – 122 –

KV-ES29M90
RM-916
H1 [LED, SIRCS RECEIVER] H2 [AV INPUT, PRESET KEY, PHONE OUT] H3 [TOP KEY]
– H1 Board –
– H2 Board –
– H3 Board –
– 123 –
KV-ES29M90
RM-916
B3 BOARD IC309 TC7SET04F (TE85R) B3 BOARD IC505 TC7SET04F (TE85R)
G 5 NC 1 5 VCC
IN A 2
B3 BOARD IC506 TC7SET04F (TE85R)

GND 3 6 OUT V
IN A 1 OUT Y
B3 BOARD WAVEFORMS
1 2 3 4 5
1.7Vp-p (H) 1.0Vp-p (H) 1.1Vp-p (H) 4.7Vp-p (V) 4.9Vp-p (V)
6 7 8 9 10
2.3Vp-p (V) 2.2Vp-p (V) 2.8Vp-p (V) 3.1Vp-p (V) 0.6Vp-p (H)
11 12 13 14 15
0.6Vp-p (H) 1.0Vp-p (H) 3.5Vp-p (V) 0.9Vp-p (H) 0.6Vp-p (H)
16 17 18 19 20
0.5Vp-p (H) 3.7Vp-p (V) 0.6Vp-p 0.1Vp-p (H) 0.6Vp-p
– 124 –
(7) Schematic Diagram of B3 (1/6) Board
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
V PULSE
A1 GND
H PULSE B1 GND
C 5V
IC506 D5V
A2 GND
A5V-1 TC7SET04F(TE85R) B2 GND

LEVEL SHIFT
Q520 A3 GND
-0.1 DTC144EKA-T146
0.2 R998
L511 10k INVERTER B3 GND
4
R557 XRST5 :CHIP R527

WSYNC 1k :CHIP A4 GND
#
:CHIP HP 100 OUT
2
4.6 MID BUSY

YMCK 2.9 D3.3V B4 MID BUSY
5
W1 FPD
-0.0 FL504 A5 FPD
L503 R598
CKD510JB1A105ST R501 100 FB503 B5 GND
:CHIP
D R571
0 R558
100
C514
0.1
5V
C560
D3.3V-1 EMI +3.3V
100
R502
:CHIP :CHIP
FB504
0UH
A6 HP 100 OUT
:CHIP C516 25V 0.01 100 :CHIP 0UH
:CHIP B6 VP 100 OUT
C517 0.1 R556 B:CHIP C515 R553 B:CHIP IC505 L504
0.01 25V 0.01 0 Y
# TC7SET04F(TE85R) Y 100 OUT A7 Y 100 OUT
B:CHIP B:CHIP :CHIP B:CHIP :CHIP FL512 :CHIP R503
LEVEL SHIFT C539
CKD510JB1A105ST C502 0 :CHIP
C501 -0.1 D3.3V-MID 47 B7 GND
C503 10 0.2 U
R575 0.01 C542 C540 16V
R560 R559 R554 C518 10 1 16V
R555 B:CHIP 47 :AL-CP U 100 OUT A8 U 100 OUT
4
82 R572 15k 47 16V :AL-CP 0.01 R504

47 15k 47 5V 5V 16V
:RN-CP 47 :CHIP 16V :AL-CP B:CHIP 0 :CHIP
R574 :RN-CP :CHIP :RN-CP :AL-CP B8 GND
VP 100 OUT
2
:RN-CP 4.6
C519 1k
R573 R552
EMI 5V 3.1 R597
V
0.1 :RN-CP R551 R528 V 100 OUT A9 V 100 OUT
5
15k 47 6 10k R505

25V 82 330
:RN-CP :RN-CP 5V 0.0 :CHIP 0 :CHIP
F:CHIP :RN-CP :CHIP XRST B9 GND
E C520
-0.1
R550
0.7
FL501
Q521
R994 7 DPIC SW
R540 1k :CHIP
A10 DPIC SW
R576 -0.1 4.4 2SC1623-L5L6 Q519
0.1 82 LPF 5 220 R596
82 B10 PORT 3
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
25V :RN-CP C504 BUFFER C559 :CHIP DTC144EKA-T146 1k :CHIP

:RN-CP 2.2 INVERT
F:CHIP # 0.0 R529 0.01 HP SUB PLL
CLK
XSYNC
CLPEN
-0.1 HP SUB IN A11 RESET 100

EXTCLP
5.6k R520 R518

GND(A)
GND(B)
B:CHIP C510
VCC(A)
VCC(B)
VRT(A)
VRT(B)
4.4
CLPV(A)
CLPV(B)
R548
VIN(A)
VIN(B)
3.1
4.6
1.4
4.6
1.4
4.6
3.2
1.4
1.9
2.3
2.3
:RN-CP 560 0 0.01 FB501

-0.1
R578 R506
-0.0
1.2
IBIAS(A)
IBIAS(B)
0.0 47 :RN-CP :CHIP Y MAIN IN B11 GND

47 :RN-CP Q501 L512 FL505 B:CHIP 100 :CHIP OUH
:RN-CP
1 2 3 4 5 6 CKD510JB1A105ST
5V 2SA1162-G R996
VRB(A) VRB(B) VP SUB IN SDA A12 SDA
48
1
R549 330 :CHIP L502

R577 47 BUFFER 1.6
:CHIP
R561 R995
47 OE(A) OE(B) 1-233-877-21 EMI B12 SCL
47
:RN-CP A5V SCL

2
560 R997 220 :CHIP R507 FB502

:RN-CP
-0.1 -0.1
2 R519 :CHIP 330 :CHIP 100 :CHIP OUH
NT/PAL MODE0 +2.5V A13 +5V DIGITAL
46
+5V
3
4.6 Q502 # Q522 :CHIP C512

0.0 12 10 9 7
2SC1623-L5L6 0.01
F TEST MODE1 2SC1623-L5L6 EMI B13 +2.5V
45
5V
4
B:CHIP
-0.1 -0.1 BUFFER BUFFER
DGND(QA) DGND(QC) 5V A14 +3.3V
44
+3.3V
5
-0.1 -0.1 1.9 25.8

Y7 C505 FL508
D(A)8 D(C)1 B14 A5V
43
5V
6
R523 R521 CKD510JB1A105ST

0.8 -0.1 10 4.4 4.4 R508 100 :CHIP
Y6 560 0
16V
D(A)7 D(C)2 A15
42
:RN-CP :CHIP V MAIN IN A5V-1 H-PULSE SUB IN

7
:AL-CP SUB-HP
Y5 1.2 IC501 -0.1 R530 Q512 +2.5V
D(A)6 TLC5733AIPM D(C)3 5.6k B15 GND
41
2SC1623-L5L6 1.3
8
-0.1 :RN-CP 0.0 C529 +9V R509 100 :CHIP

Y4 1.0 A/D CONVERTER BUFFER
1.2
5V # 4.4
D(A)5 D(C)4 A16 +9V
40
9
R522 SUB-VP
Y3 1.6 -0.1 R531 1 2 3 # R562
D(A)4 D(C)5 Y SUB IN Q510 B16
10
39
180 560 V-PULSE SUB IN

-0.1 R534 SUB V R510 560 :CHIP
Y2 0.4 :CHIP :CHIP C530 1.3 2SC1623-L5L6
C506 0.7 #
D(A)3 D(C)6 A17 V SUB IN
11
38
# Q503 0 BUFFER
1.2 1.4 4.4
G Y1
D(A)2 D(C)7 2SC1623-L5L6
:CHIP
B17 PORT 2
12
37
C521 R585 R511 560 :CHIP

Y0 1.4 1.4 0.01 BUFFER 6 4 # 2.2
FL502 C531 SUB U
D(A)1 D(C)8 Q523 A18 U SUB IN
13
36
B:CHIP 1.4 LPF # R535

1.3 3.1 C507 2SC1623-L5L6 4.4
0.7
0.0 #
VDD(QA) VDD(QC) 4.4 1-233-504-21 V SUB IN B18 PORT 1
14
35
10 R526 R524 BUFFER

16V 4.4 Q511 SUB Y R512 560 :CHIP
3.1 560 0 R583
:AL-CP C532 2SC1623-L5L6 R581
DGND(QB) OE(C) A19 Y SUB IN
15
34
R532 :RN-CP :CHIP U MAIN IN 0 #

1.6 # R536 L501 FL509
0.1 1.3 -0.0 0.7 5.6k :CHIP
BUFFER
2.2k CKD510JB1A105ST
VDD(QB) VRB(C) :RN-CP B19 GND
16
33
:CHIP :CHIP
0.7 R564
28 CLPV(C)
27 IBIAS(C)
R525 R584 R582

32 GND(C)
C522
30 VCC(C)
29 VRT(C)
3.0 1 2 3 # EMI A20 GND

31 VIN(C)
25 DGND
C523 0.1 R533 # R563 C538 R594 470 470 +2.5V-1

19 D(B)6
20 D(B)5
21 D(B)4
22 D(B)3
23 D(B)2
24 D(B)1
17 D(B)8
18 D(B)7
-0.1
0.1
4.6
2.2
3.2
4.6
2.2
1.0
1.7
1.7
1.5
2.2
1.8
1.7
1.6
1.8
26 VDD
0.01 25V 180 560 0.01 470 :CHIP :CHIP C509 R513
B:CHIP F:CHIP :CHIP :CHIP B:CHIP :CHIP 0.01 560 :CHIP
B20 GND
MAIN Y
C508
#
R565
# Y MAIN IN
B:CHIP
A21 Y MAIN IN B3 BOARD IC501 TLC5733A1PM
H C533 5V R567 R537
R514
C7
C6
C5
C4
C3
C2
C1
C0
6 4 2.2k B21 GND

FL503 # # 560 :CHIP
3
LPF
:RN-CP MAIN U VPO DGND
ADTB R579 U SUB IN U MAIN IN A22 U MAIN IN
15k 1-233-504-21 C534 R538 R515
:CHIP G
C524 FL510 FL511 0 R566 # 560 :CHIP
B22 GND CLK A
10 CKD510JB1A105ST CKD510JB1A105ST :CHIP MAIN V
# :RN-CP
16V Q515 V MAIN IN A23 V MAIN IN
:AL-CP C511
C525 R580 0.1 2SC1623-L5L6 R539 R516 8 8 8
B23 GND
10 0 BUFFER # 1k :CHIP VIN(A) D(A)1-8
EMI
EMI
C526 C528 25V MAIN VP

16V 0.01 :CHIP F:CHIP :RN-CP
0.01 VP MAIN IN A24 V-PULSE M-IN
:AL-CP B:CHIP B:CHIP VDOCBCLVL SAMPLING
D3.3V-1
R517
B24 GND VRT(A) VDD(QA)
Q514
R587 1k :CHIP
MAIN HP
COMPARATOR
C527 1k 8
5V HP MAIN IN A25 H-PULSE M-IN DGND(QA)
I 0.1
25V
B:CHIP
2SC1623-L5L6
BUFFER
:CHIP C535
0.1
25V
R586
1k
B25 GND
C536
0.1
F:CHIP :CHIP VRB(A)
25V
CN502
5V
F:CHIP 50P CLPV(A) CLAMP
VDOCRCLVL :BTOB CONTROL
R590 5V TO A BOARD
IBIAS(A)
1k R589
:CHIP CN1108
1k
:CHIP
VCC(A)
GND(A)
0.0
J VDOYCLVL
0.0
Q513
2SC1623-L5L6 OE(A)
BUFFER
R591
CLK B
1k C537 0.0
:CHIP 0.1
25V 8 8 8
F:CHIP R592 VIN(B) D(B)1-8
1k
:CHIP SAMPLING
VRT(B) VDD(QB)
COMPARATOR
Q517
8 DGND(QB)
2SC1623-L5L6
BUFFER
K 4.9
L505 L506 VRB(B)
:CHIP :CHIP
L508
4.9 CLPV(B) CLAMP
D5V CONTROL
:CHIP C545
C546 47 IBIAS(B)
4.2 C548
0.01 16V 0.01
:AL-CP
C554
B:CHIP B:CHIP VCC(B)
R993
0.01 47k
L509
B:CHIP :CHIP GND(B)
:CHIP
IC504
TLC2933IPWR OE(B)
L R943
220
PLL R984
3.3k
R985
470k
C551
0.01
R982
330
C550
0.01
C549
47
L507
# C543 FL506
CLK C
:CHIP :CHIP :CHIP B:CHIP :CHIP B:CHIP 16V :CHIP 0.01 CKD510JB1A105ST
4.1 4.1 5V
:AL-CP B:CHIP 8 8 8
14
1
R942 0.0 0.0 A5V-1 EMI +5V VIN(C) D(C)1-8

13
330
2
:CHIP 1.8 0.0 SAMPLING VDD(QC)

CK54
VRT(C)
12
COMPARATOR
3
R991 3.1 -0.1

0 :CHIP 5V 8 DATA DGND(QC)
11
4
R1 1.5 0.0 R981 5V

HREF Q516
330 LATCH
10
5
0.5 -0.1 :CHIP

2SC1623-L5L6 A5V
VRB(C)
6
0.0 3.3V REG

-0.1
M A3.3V CLPV(C) CLAMP
7
C557
3.3VGR Q524
0.01 R988
B:CHIP 220 R983 2SC1623-L5L6
CONTROL
:CHIP 47k
3.3V REG IBIAS(C)
:CHIP
R990 R989 R956
470k 22k R987 D501 VCC(C)
(DRC, MID, DRC/MID CONTROLLER) :CHIP :CHIP 1k
:CHIP Q518
MA8039
47k
:CHIP
2SA1037K-T146-QR
REFERENCE GND(C)
C556
BIAS
100
6.3V R986 OE(C) CLK A
:AL-CP 3.3k
:CHIP MODE0
EXTCLP CLK B CLOCK OUTPUT FORMAT
CLAMP PULSE
N C555 CLPEN INT/EXT CLK C
GENERATOR /TEST MODE1
0.1 SWITCHING
25V CONTROL TEST
F:CHIP NT/PAL
CLK XSYNC
O
B-SSS10133-HK.-B3(P1)-ES29
– 125 – – 126 – – 127 – – 128 –

(8) Schematic Diagram of B3 (2/6) Board
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21
YMCK
W1
A
D5V
IVDD B3 [DRC, MID, SUB MICON, DRC/MID CONTROLLER]

DICD7
DICD6
DICD5
DICD4
DICD3
DICD2
DICD1
DICD0
DIYD7
DIYD6
DIYD5
DIYD4
DIYD3
DIYD2
DIYD1
DIYD0
R687 Q601 3.3VGR

IVDD 1 0
ADTB 2SC1623-L5L6
IHDD :CHIP 0.0
IHDD 2 BUFFER Q602 C639
4.9 L604 C638
W13ID 3
W13ID
C637 FL601
C601
10
VP MAIN IN
2SC1623-L5L6
BUFFER
0.01
B:CHIP :CHIP
0.01
B:CHIP
– B3 Board (Component Side) –
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
:CHIP
0.01 CKD510JB1A105ST 16V 0.0

GND 4 D5V
B:CHIP :AL-CP R688 L605
DIYD7 8
B DIYD7 5 +2.5V-1 EMI
3.3k
:CHIP R689 :CHIP
10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
10k
DIYD6 R658 2.2k R690

DIYD6 6 G
:CHIP 0.2 IC603
1k 0
TLC2932IPW
R686
R685
R684
R683
R682
R681
R680
R679
R678
R677
R676
R675
R674
R673
R672
DIYD5 :CHIP :CHIP 4.9 C642

DIYD5 7 PLL R600 0.01
HP MAIN IN 2.9 B:CHIP
DIYD4 R671 C629 2.9 5.1k
DIYD4 8 0.2 :CHIP
0.01 R691
Y7
Y6
Y5
Y4
Y3
Y2
Y1
Y0
10k

Trinitron Kves29m90 PDF

Uploaded by

Copyright:

Available Formats

Trinitron Kves29m90 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Trinitron Kves29m90 PDF

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL AG3 CHASSIS

KV-ES29M90 RM-916 Hong Kong SCC-P27A-A

Downloaded from www.Manualslib.com manuals search engine

Power requirements 110-240 V AC, 50/60 Hz

Design and specifications are subject to change without notice.

CAUTION SAFETY-RELATED COMPONENT WARNING!!

Section Title Page Section Title Page

SELF DIAGNOSIS FUNCTION ................................ 4 6. DIAGRAMS

SELF DIAGNOSTIC FUNCTION

1. DIAGNOSTIC TEST INDICATORS

Diagnostic No. of times Self-diagnostic Probable Detected

Note 1: Refer to screen (G2) Adjustment in section 4-5 of this manual.

2. DISPLAY OF STANDBY/TIMER LIGHT FLASH COUNT

Lamp ON 0.3 sec.

Diagnostic Item Flash Count*

* One flash count is not used for self-diagnostic.

3. STOPPING THE STANDBY/TIMER FLASH

4. SELF-DIAGNOSTIC SCREEN DISPLAY

[To Bring Up Screen Test]

[Screen display] / channel [5] / Sound volume [-] / Power ON

Self-Diagnosis screen display

5. HANDLING OF SELF-DIAGNOSTIC SCREEN DISPLAY

[Clearing the result display]

[Quitting Self-diagnostic screen]

IC4301 IC001 IC003

[+B overcurrent ªOCPº] Occurs when an overcurrent on the +B(135) line is detected by Q6610

[+B overvoltage ªOVPº] Occurs when an overvoltage on the +B(135) line is detected by D6635,

[Vertical deflection failure] Occurs when an absence of the vertical deflection pulse is detected by

[High voltage protector of Horizontal Deflection] Occurs when an overvoltage of horizontal pulse is detected by D6809 and

Using Your New TV

Do not operate the TV if any liquid or solid object

VIDEO OUT To S video R R

Downloaded from www.Manualslib.com manuals search engine

remote control cover. (not supplied) R

• When connecting video game equipment, display the “FEATURE” menu

jacks at the rear of your TV.

Connecting audio/video equipment using the T

audio inputs audio

• If you select “DVD” on your TV screen, no signal will be output at the

T (monitor output) jacks (see page 11).

Using Your New TV 5 6 Using Your New TV

Downloaded from www.Manualslib.com manuals search engine

Component video cable To

To component LINE OUT

video output (yellow) R

Connect To (on the DVD player)

• When connecting to (component video input) on your TV, you must

Using Your New TV 7 8 Using Your New TV

Downloaded from www.Manualslib.com manuals search engine

and operations used while watching the

1 Press ! to turn on the TV.

2 Press PROGR +/– or the

To select a TV program quickly

Using Your New TV 9 10 Using Your New TV

Downloaded from www.Manualslib.com manuals search engine

DRC-MF Using the Remote Control Button Joystick ( )

right (see page 29). 0

1 2 3 To confirm a selected item, press . PIC

You can also press ENTER on the remote PROGR