HPE0 S50 Demo

Page No | 1
HP
HPE0-S50 EXAM
Integrating HPE Synergy Solutions
Product: Demo File
For More Information:

https://www.dumpsplanet.com/HPE0-S50-dumps
https://www.dumpsplanet.com
m/
Questions & Answers Page-2
PDF
Question: 1
A customer that uses a third-party array plans to set up Fiber Channel (FC) with the new
HPE Synergy 12000 Frame.
Which tool creates the FC zones in a Synergy solution?
A. storage pages in the Synergy console

B. Virtual Connect module manager
C. corresponding SAN manager
D. Storage array command line utility
Answer: A
Question: 2
CORRECT TEXT
A customer has purchased 15 synergy Frames with the following components:
How many frames can the configuration for the Logical Enclosure? (Note: Enter your answer
in the answer field below.)
Answer: 6
Question: 3
A synergy integration creating a network that must be connected from the Synergy Connect
SE 40Gb FB module to an Ethernet switch carrying 500 VLANs for the hypervisor cluster.
Which network should the synergy integrator select during network creation?
A. Ethernet Tunneled
B. Ethernet Channel
C. Ethernet Tagged
D. Ethernet Untagged
Answer: A
Question: 4
How should a synergy integrator configure an HPE Synergy solution to provide shared storage to
all compute nodes in a single frame?
A. Use composer to configure the p55420 smart array controllers to HBA mode and
configure the server profile to include SAN storage.
B. Import a Linux based NFS into Composer and configure the server profile to include SAN
storage.
C. Use Composer to configure a HPE Synergy D3940 storage and configure the server
https://www.dumpsplanet.com Page 2
PDF
profiles to include SAN storage.

D. Import s Stresses SPAR system Composer and configure the server profiles to include SAN
storage.
Answer: D
Question: 5
A Synergy integration needs a supported approach to upgrade HPE drivers on HPE Synergy
Modules that run VMware ESX.
Which resource should the Synergy integrator use?
A. Integrity Support Pack

B. intelligent Provisioning
C. ProLiant Support Pack for VMware
D. Software Delivery Repository
Answer: A
Question: 6
A Synergy integration is unable to assign an HPE 3PAR virtual volume to a new profile in
HPE OneView. The Virtual Volume has been previously assigned to another profile.
Which setting in HPE OneView preventing the integrator from assigning the volume to the
new profile?
A. shared under storage pools

B. private under volumes
C. private under storage pools
D. shared under volume
Answer: A
Question: 7
As part of a synergy implantation synergy integration needs to create 100 networks in a
Logical Interconnect Group (LIG) configuration. The network administration for the end-of-
row (EoR) switches provides a CSV file with the network that need to be created.
How should the Synergy Integrator automate the creation of the 100 networks?
A. Upload the CSV file to the Composer and execute the Create Networks wizard.
B. Use the HPE OneView PowerShell library to create the networks listed in the CVS file.
C. Start HPE SUT to migrate the CSV file to a Synergy configuration file and upload it to the
composer.
D. Configure Image stream to automate the network configuration.
Answer: B
Question: 8
Which composer of the HPE Synergy solution provides a customer with the ability to rapidly
PDF
provision a consistent operation environment?
A. OpenView
B. Reference Architecture
C. Composer
D. Image Streamer
Answer: B
Question: 9
When should IP address be assigned using an IPv6 address pool in the Composer? (Select two.)
A. when configuring management NICs in an operating system

B. when booting to an iSCSI initiator with image Streamer
C. when PXE booting from the deployment server
D. when configuration Composer appliance
E. when configuration interconnects modules
Answer: DE
Question: 10
A customer reports that performance is not adequate for an application using a hybrid HPE
StoreVirtual VS
A. How can a Synergy integrator improve performance for this application?
A. Enable adaptive optimization on the volume for the application.
B. Change the volume for the application on the VSA to thick provisioned.
C. Migrate the volume from Network RAID10 to Network RAID50.

D. Change the volume for the application on the VSA to thin provisioned.
Answer: B
Page No | 5
Thank You for Trying Our Product
Our Certification Exam Features:
★ More than 99,900 Satisfied Customers Worldwide
★ Average 99.9% Success Rate
★ Free Update to match latest and real exam scenarios
★ Instant Download Access! No Setup required.
★ Questions & Answers are downloadable in PDF format.
★ Multi-Platform capabilities - Windows, Laptop, Mac, Android, iPhone, iPod, iPad
★ 100% Guaranteed Success or 100% Money Back Guarantee.
★ Fast, helpful support 24x7
View Certification Exam page for Full Product:
https://www.dumpsplanet.com/HPE0-S50-dumps

HPE0 S50 Demo

Uploaded by

Copyright:

Available Formats

HPE0 S50 Demo

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HPE0 S50 Demo

Uploaded by

Copyright:

Available Formats

Page No | 1

Product: Demo File

For More Information:

A. storage pages in the Synergy console

profiles to include SAN storage.

A. Integrity Support Pack

A. shared under storage pools

provision a consistent operation environment?

A. when configuring management NICs in an operating system

C. Migrate the volume from Network RAID10 to Network RAID50.

Thank You for Trying Our Product

Our Certification Exam Features:

★ More than 99,900 Satisfied Customers Worldwide

★ Average 99.9% Success Rate

★ Free Update to match latest and real exam scenarios

★ Instant Download Access! No Setup required.

★ Questions & Answers are downloadable in PDF format.

★ Multi-Platform capabilities - Windows, Laptop, Mac, Android, iPhone, iPod, iPad

★ 100% Guaranteed Success or 100% Money Back Guarantee.

★ Fast, helpful support 24x7

View Certification Exam page for Full Product:

You might also like