Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 37 views

    Saic A 1005

    Uploaded by

    Naushad Alam
    The document is a Saudi Aramco inspection checklist for compaction testing. It contains 15 items to inspect regarding compaction testing acceptance criteria and procedures. The checklist references Saudi Aramco standards SAES-A-114 and SAES-Q-006 and requires that compaction meet a minimum percentage of modified Proctor density, including 90% under footings and foundations. Nuclear density gauges used must have a valid calibration certificate per ASTM D6938.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd

    Saic A 1005

    Uploaded by

    Naushad Alam
    37 views3 pages
    The document is a Saudi Aramco inspection checklist for compaction testing. It contains 15 items to inspect regarding compaction testing acceptance criteria and procedures. The checklist references Saudi Aramco standards SAES-A-114 and SAES-Q-006 and requires that compaction meet a minimum percentage of modified Proctor density, including 90% under footings and foundations. Nuclear density gauges used must have a valid calibration certificate per ASTM D6938.

    Original Description:

    saudi aramco inspection checklist updated

    Original Title

    SAIC-A-1005

    Copyright

    © © All Rights Reserved

    Available Formats

    XLSX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document is a Saudi Aramco inspection checklist for compaction testing. It contains 15 items to inspect regarding compaction testing acceptance criteria and procedures. The checklist references Saudi Aramco standards SAES-A-114 and SAES-Q-006 and requires that compaction meet a minimum percentage of modified Proctor density, including 90% under footings and foundations. Nuclear density gauges used must have a valid calibration certificate per ASTM D6938.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    37 views3 pages

    Saic A 1005

    Uploaded by

    Naushad Alam
    The document is a Saudi Aramco inspection checklist for compaction testing. It contains 15 items to inspect regarding compaction testing acceptance criteria and procedures. The checklist references Saudi Aramco standards SAES-A-114 and SAES-Q-006 and requires that compaction meet a minimum percentage of modified Proctor density, including 90% under footings and foundations. Nuclear density gauges used must have a valid calibration certificate per ASTM D6938.

    Copyright:

    © All Rights Reserved
    Download as XLSX, PDF, TXT or read online from Scribd
    Download as xlsx, pdf, or txt
    You are on page 1of 3

    SAUDI ARAMCO ID/PIEU - 15-Nov-2017 - REV. 2016.06.00 (Standards Cutoff -June 30, 2016) Rev. 2016.06.

    00 30-Jun-16
    SAIC NUMBER DATE APPROVED QR NUMBER
    SAUDI ARAMCO INSPECTION CHECKLIST
    Compaction Testing SAIC-A-1005 15-Nov-17 CIVIL-
    PROJECT TITLE WBS / BI / JO NUMBER CONTRACTOR / SUBCONTRACTOR

    EQUIPMENT ID NUMBER(S) EQUIPMENT DESCRIPTION EQPT CODE SYSTEM ID. PLANT NO.

    LAYOUT DRAWING NUMBER REV. NO. PURCHASE ORDER NUMBER EC / PMCC / MCC NO.

    SCHEDULED INSPECTION DATE & TIME ACTUAL INSPECTION DATE & TIME QUANTITY INSP. MH's SPENT TRAVEL TIME
    SAUDI ARAMCO USE ONLY
    SAUDI ARAMCO TIP NUMBER SAUDI ARAMCO ACTIVITY NUMBER WORK PERMIT REQUIRED?

    SAUDI ARAMCO INSPECTION LEVEL CONTRACTOR INSPECTION LEVEL

    ITEM
    ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
    No.

    Note: To verify that the area/ material being inspected was tested by
    SA approved third party testing agency, the test results attached with
    this RFI shall be verified by the relevant PID inspection unit if copy of
    the test results had been received directly from the third party lab. If
    not available in the PID Inspection Unit, the inspector shall contact
    the third party laboratory representative and request for an
    explanation. If the explanation is not reasonable, NCR shall be
    issued to the third party lab through the Batch Plant and Civil Testing
    Group.

    Contractor's testing agency shall be a Saudi ARAMCO-approved SAES-A-114


    A1
    independent civil testing agency. Sec. 5.1.1

    One Modified Proctor Test per ASTM D1557 with corresponding


    SAES-A-114
    A2 Proctor curve shall be performed for each type of fill material or
    Sec. 6.4.1.1
    where there is a change in the type or the source of material.

    For cohesionless free draining soils, ASTM D4253 Maximum Index


    Density and Unit Weight of Soils Using a Vibratory Table and ASTM
    D4254 Minimum Index Density and Unit Weight of Soil and SAES-A-114
    A3
    Calculation of Relative Density shall also be performed for each type Sec. 6.4.1.1
    of cohesionless, free draining material or where there is a change in
    the type or the source of material..

    In-place density shall be determined using one of the following:


    ASTM D-1556 Sand Cone Method;
    SAES-A-114
    A4 ASTM D-2167 Rubber Balloon Method;
    Sec. 6.4.2.1
    ASTM D-6938 Nuclear Method;
    or ASTM D-2937 Drive-cylinder.

    Acceptance testing of in-place density and moisture content (field


    density testing) on compacted fill will be performed at the following
    rates:
    1. Under all foundations - one test every 1077 ft² (100 m²) of each lift.
    2. Under area paving - one test every 2153 ft² (200 m²) of each lift. SAES-A-114
    A5
    3. Road base and sub-base - one test every 2153 ft² (200 m²) of Sec. 6.4.2.3
    base or sub-base.
    4. Backfill of trenches - one test for every 50 linear ft (15 m) of each
    lift.
    5. General fill - one test every 5382 ft² (500 m²) of each lift.

    As a minimum, at least one in-place density test must be performed


    SAES-A-114
    A6 on every lift of fill and further placement shall not be allowed until the
    Sec. 6.4.2.4
    required density has been achieved.

    Nuclear density gauges, when used, shall have a valid calibration SAES-A-114
    A7
    certificate per the requirement of ASTM D6938, Sec. 8. Sec. 3.2

    Saudi Aramco: Company General Use


    Fill or backfill placed beneath footings, grade beams, mats, buildings
    SAES-A-114
    A8 or process areas shall be compacted to at least 90% of the maximum
    Sec. 6.3.6.1
    Modified Proctor density as determined by ASTM D1557.

    Saudi Aramco: Company General Use


    SAUDI ARAMCO ID/PIEU - 15-Nov-2017 - REV. 2016.06.00 (Standards Cutoff -June 30, 2016) Rev. 2016.06.00 30-Jun-16
    SAIC NUMBER DATE APPROVED QR NUMBER
    SAUDI ARAMCO INSPECTION CHECKLIST
    Compaction Testing SAIC-A-1005 15-Nov-17 CIVIL-
    PROJECT TITLE WBS / BI / JO NUMBER CONTRACTOR / SUBCONTRACTOR

    ITEM
    ACCEPTANCE CRITERIA REFERENCE PASS FAIL N/A RE-INSP DATE
    No.

    For cohesionless free draining soils, 70% relative density as


    SAES-A-114
    A9 determined by ASTM D4253 and ASTM D4254 shall be achieved
    Sec. 6.3.6.4
    under footings, grade beams, mats, buildings or process areas.

    Under foundations with static loads over 320kPa and foundations for
    vibrating or heavy machinery and pavements, 85% of relative density
    SAES-A-114
    A10 (ASTM D4253/ASTM D4254) for cohesionless soils or 95% of of the
    Sec. 6.3.6.2
    maximum density as determined by ASTM D1557 for cohesive
    materials.

    When the backfill material cannot clearly be classified as cohesive or


    cohesionless both relative density and Proctor density tests must be SAES-A-114
    A11
    performed. The backfill shall then be compacted to the greater Sec. 6.4.1.1
    density.

    The compaction requirement for base coarse shall not be less than
    SAES-Q-006
    A12 98% of the maximum laboratory dry density as determined by ASTM
    Sec. 5.2.2.2
    D1557 or AASHTO T180..

    The compaction requirement for subbase shall not be less than 95%
    SAES-Q-006
    A13 of the maximum laboratory dry density as determined by ASTM
    Sec. 5.2.2.2
    D1557 or AASHTO T180..

    Compacted surfaces of fill and backfill shall be finish graded to the


    SAES-A-114
    A14 cross sections, lines, grades, and elevations as indicated on the
    Sec. 6.3.7
    drawings.

    The depth of the test holes shall be no greater than 300mm (12 SAES-A-114
    A15
    inches) deep. (ASTM D 2922, Sec. 1.1) Sec. 6.4.2

    REMARKS:

    REFERENCE DOCUMENTS:
    1- SAES-A-114 -- Excavation and Backfill, 30 September , 2014
    2- SAES-Q-006 -- Asphalt Concrete Pavement, 26 November 2014

    Contractor / Third-Party Saudi Aramco


    Construction Representative* PMT Representative
    Work is Complete and Ready for Inspection: T&I Witnessed QC Record Reviewed Work Verified
    Name, Initials and Date: Name, Initials and Date:

    QC Inspector PID Representative


    Performed Inspection Work / Rework May Proceed T&I Witnessed QC Record Reviewed Work Verified
    Name, Initials and Date: Name, Initials and Date:

    QC Supervisor Proponent and Others


    Quality Record Approved: T&I Witnessed QC Record Reviewed Work Verified
    Name, Organization,
    Name, Sign and Date:
    Initials and Date:

    *Person Responsible for Completion of Quality Work / Test Y = YES N = NO F = FAILED

    Saudi Aramco: Company General Use

    You might also like