150219110213amended BoQ Pkg-3 Vol II of III

ODISHA POWER TRANSMISSION CORPORATION LIMITED
NAME OF THE WORK:-Design, Supply and Installation of 2X500 MVA ICT for Out Door Type,400/220 KV GIS Grid Sub-station at
(Ramkrushnapur),Bhadrak.in Odisha State of India under PACKAGE-3 Under Japan International Cooperation Agency (JICA)’s ODA Loan.
Loan Agreement No: [ID-P245] - FB No: [CPC/JICA/ICB/03 /18-19]- Reference Identification No: [OPTCL/JICA/PKG-3]
Schedule No. 1. Plant Supplied from Abroad (Sub-station )
NAME OF THE BIDDER
Out Door type GIS S/S (New):400 KV Bay-

5 Nos.(FDR-2,TFR-2& B/C-1),220 KV Bay-
Quantity for: Construction of 2x500 MVA
2
Unit Price
400/220/33 GIS S/S at Ramkrushnapur
2 Nos.(FDR-2,TFR-2,B/C-1)
SUPPLY OF FOLLOWING EQUIPMENTS 2
SL. NO. Code1 UNIT
In Foreign Total Price
(As per Technical Specification)
CIP
Currency
(1) (2) (3) (1) x (3)

3150A, 63kA for 3s, one and half Circuit Breaker (Circuit breaker
shall be E2-C2-M2 class as per IEC 62271-100) arrangement. 420kV
1 OUTDOOR GIS EQUIPMENT as per latest IEC standard & type tested
equipment as per technical specification, with open future proof &
flexible system in line with IEC 61850 & IEC 62271-203.
420kV,3150A, 63KA for 3 sec (Busbar, CB, Disconnector, Grounding
switch, CT & PT), SF6 gas insulated Complete Diameter module (2 Nos
Feeder) each comprising of SF6 gas insulated Single Pole Circuit Breaker
(3 Sets) with CSD (Control Switching Device), Single Phase Current
Transformer (18 Nos), Single Phase Potential Transformer (4 Winding) (6
Nos), Motorised 3 Phase Disconnector (6 Sets), Motorised safety
Grounding switch (8 Nos), Motorised 3 Phase Disconnector with high
speed fault making Motorised Grounding switch (2 Nos), Local Control
Cubicle, SF6 gas monitoring system for complete diameter, SF6 bus duct
1.1 termination arrangement, online PD sensor (adequate number of UHF Set 3
sensors in the offered GIS equipment for detection of Partial discharge (of
5 pC and above) as per IEC 60270 through Partial Discharge (PD)
monitoring system), different gas compartment, O-ring & gaskets, Nuts,
Bolts & Washers for Outdoor use, Absorbent,Limit Switch, SF6 Gas, etc.
to complete diameter module & its earthing arrangement with earthing
strips of adequate size (as per IEEE Std 80-2013 to protect operating staff
against any hazardous touch voltages and electro-magnetic
interferences) as per the technical specification.
420kV,3150A, 63KA for 3 sec (Busbar, Disconnector, Grounding Switch &

Bus PT), 3 Phase Isolated, SF6 gas insulated, metal enclosed busbars
Complete Diameter module (2 Nos BUS-PT) in bus enclosures running
along the length of the switchgear to interconnect each of circuit breaker
diameter module. Each busbar set shall be complete with Potential
Transformer (4 Winding), Motorised 3 Phase Disconnector (1 No),
Motorised Busbar safety Grounding switch (1 No), Local Control Cubicle,
SF6 gas monitoring system online PD sensor (adequate number of UHF
1.2 sensors in the offered GIS equipment for detection of Partial discharge (of Set 1
Bolts & Washers for Outdoor use, Absorbent, Limit Switch, SF6 Gas, etc.
420kV, 3150A, 63kA, 3 Sec, Single phase, SF6 gas Insulated Bus Duct
outside GIS Bay along with associated Support structure arrangement
bends, joints, accessories, & its earthing arrangement with earthing strips
1.3 RM 900
of adequate size (as per IEEE Std 80-2013 to protect operating staff
interferences) etc. as per the technical specification.
420kV, 3150A, 63kA, SF6/Air BUSHING (Bushing shall be of Polymer /
composite insulator type and shall be seamless sheath of a silicone
rubber compound. The hollow silicone composite insulators shall comply
1.4 No 18
as per IEC 61462 and IEC 62217. The design of the composite insulators
shall be tested and verified according to IEC 61462) FOR CONNECTING
GIS TO AIS along with support structure.
Online continuous Partial Discharge Monitoring System (PDM):
420kV GIS equipment system shall have Online continuous Partial
Discharge Monitoring System (PDM) system to provide an automatic
facility for the simultaneous collection of PD data at multiple points on the
GIS & its associated GIB ducts and Voltage Transformers adopting UHF
technique & the data stored shall provide a historical record of the
progress of PD sources and shall identify the areas of maximum activity.
1.5 Set 1
PDM system shall be interfacing with UHF PD couplers provided. The PD
Monitoring PC Work Station along with all accessories shall be
considered. Power supply to PDM PC shall have protection against
surges, overload and short circuit. A dedicated on-line UPS system shall
also be provided as a backup during supply interruption, to ensure trouble-
free & reliable running of the PDM System for a minimum of 15 minutes
duration.
3150A, 50kA for 3s, Double Busbar Circuit Breaker (Circuit breaker
shall be E2-C2-M2 class as per IEC 62271-100) arrangement.
245kV OUTDOOR GIS EQUIPMENT as per latest IEC standard & type
2 tested equipment as per technical specification, with open future
proof & flexible system in line with IEC 61850 & IEC 62271-203.
245kV, 3150A, 50kA for 3 sec (Busbar, CB, Disconnector, Grounding

Switch & CT), SF6 gas insulated ICT Feeder Bay Module each comprising
of SF6 gas insulated Single Pole Circuit Breaker (1 Set), Single Phase
Current Transformer (6 Nos), Motorised Busbar 3 Phase Disconnector (2
Nos), Motorised Disconnector (1 No), Motorised safety Grounding switch
(3 Nos), Local Control Cubicle, SF6 gas monitoring system for complete
bay, SF6 bus duct termination arrangement (3 Nos), PD sensor (adequate
number of UHF sensors in the offered GIS equipment for detection of
2.1 Partial discharge (of 5 pC and above) as per IEC 60270 through Partial Set 3
Discharge (PD) monitoring system), different gas compartment, O-ring &
gaskets, Nuts, Bolts & Washers for Outdoor use, Absorbent, Limit Switch,
SF6 Gas, etc. to complete ICT Feeder Bay Module & its earthing
arrangement with earthing strips of adequate size (as per IEEE Std 80-
2013 to protect operating staff against any hazardous touch voltages and
electro-magnetic interferences) as per the technical specification.
switch, CT & PT), SF6 gas insulated Line Feeder Bay Module each
comprising of SF6 gas insulated Single Pole Circuit Breaker (1 Set),
Single Phase Current Transformer (6 Nos), Single phase Line Potential
Transformer (4 winding) (3 Nos), Motorised 3 Phase Busbar Disconnector
(2 Nos), Motorised safety Grounding switch (2 Nos), Motorised 3 Phase
Disconnector with high speed fault making Motorised Grounding switch (1
No), Local Control Cubicle, SF6 gas monitoring system for complete bay,
SF6 bus duct termination arrangement (3 Nos), PD sensor (adequate
2.2 Set 4
Partial discharge (of 5 pC and above) as per IEC 60270 through Partial
SF6 Gas, etc. to complete Line Feeder Bay Module & its earthing
245kV, 3150A, 50kA for 3 sec (Busbars, Disconnector, Grounding switch

& bus PT), 1 Phase Isolated Bus-PT Bay Module comprisig of SF6 gas
insulated metal enclosed busbars each enclosed in bus enclosures
running along the length of the switchgear to interconnect each of circuit
breaker bay module. Each busbar set shall be complete with Single phase
bus Potential Transformer (4 winding) (3 Nos), Motorised 3 Phase
Disconnector (1 No) , Motorised Busbar safety Grounding switch (1 No),
Local Control Cubicle, SF6 gas monitoring system PD sensor (adequate
2.3 number of UHF sensors in the offered GIS equipment for detection of Set 1
SF6 Gas, etc. to complete the bus & its earthing arrangement with
earthing strips of adequate size (as per IEEE Std 80-2013 to protect
operating staff against any hazardous touch voltages and electro-
magnetic interferences) as per the technical specification.
245kV, 3150A, 50kA for 3 sec (CB, Disconnector, Grounding switch &
CT), SF6 gas insulated Bus Coupler Bay Module comprising of SF6 gas
insulated Single Pole Circuit Breaker (1 Set), Single Phase Current
Transformer (6 Nos), Motorised 3 Phase Disconnector (2 Nos), Motorised
safety Grounding switch (2 Nos), Local Control Cubicle, SF6 gas
monitoring system, PD sensor (adequate number of UHF sensors in the
offered GIS equipment for detection of Partial discharge (of 5 pC and
2.4 above) as per IEC 60270 through Partial Discharge (PD) monitoring Set 1
system), different gas compartment, O-ring & gaskets, Nuts, Bolts &
Washers for Outdoor use, Absorbent, Limit Switch, SF6 Gas, etc. to
complete Bus Coupler Bay Module & its earthing arrangement with
operating staff against any hazardous touch voltages and electro-
245kV, 3150A, 50 kA, 3 sec, single phase, SF6 gas Insulated Bus Duct
bends, joints,accessories, & its earthing arrangement with earthing strips
2.5 RM 1000
245kV,3150A, 50kA SF6/Air BUSHING (Bushing shall be of Polymer /
composite insulator type and shall be seamless sheath of a silicone
rubber compound. The hollow silicone composite insulators shall comply
2.6 No 21
as per IEC 61462 and IEC 62217. The design of the composite insulators
shall be tested and verified according to IEC 61462) FOR CONNECTING
GIS TO AIS along with support structure.
Portable Partial Discharge Monitoring System (PDM):
245kV system shall have Portable Partial Discharge Monitoring System
(PDM) & shall be capable for measuring PD in charged GIS environment,
bandwidth in order of 100MHz–2GHz & provision to select a wide range of
intermediate bandwidths and the principle of operation shall be based on
2.7 UHF principle of detection. The Detection and measurement of PD and Set 1
bouncing particles having in built large coloured LCD for displaying and
storing facility in the instrument for further analysis to locate actual source
of PD such as free conducting particles, floating components, voids in
spacers, particle on spacer surfaces etc.
3.1 420 KV, 3150 A, 63 KA, Center break ISOLATORS WITH EARTH SWITCH Nos 4
420KV 1 phase Solid core bus post insulator (AIS) as per technical
3.2 NOS 6
specification.
3.3 245 KV, 2000A, 40KA, Center break ISOLATORS WITH EARTH SWITCH NOS 4
3.4 NOS 6
specification.
400KV metal oxide surge arrrestor, 20 KA , Long duration discharge
3.5 NOS 18
class IV , 12KJ/KV at 336KV as per technical specification.
216KV metal oxide surge arrrestor, 10KA Long duration discharge class
3.6 NOS 21
III , 10 KJ/KV at 216KV as per technical specification.
30 KV, METAL OXIDE SURGE ARRESTOR, 10kA, Long duration
3.7 NOS 9
discharge class III (AIS) as per technical specification.
36 KV ,1250A, 31.5 KA for 1 sec, isolator (single isolator with earth
3.8 SET 2
switch) including post insulators as per technical specification
4 36KV GIS equipment
36KV, 1250A, 31.5kA for 3 sec, SF6 gas insulated transformer bay module
each comprising of SF6 gas insulated Vacuum circuit breaker , current
4.1 transformer , bus-bar disconnectors with common grounding switch , SF6 gas SET 3
monitoring system for complete bay (having 33 KV Bus Bar of 2000 Amp) to
complete transformer bay module suitable for cable connection to transformer.
36KV, 1250A , 31.5kA for 3 sec, (33 KV Bus Bar 2000 Amp) SF6 gas
insulated bus-coupler bay module comprising of SF6 gas insulated vacuum
circuit breaker , current transformer , disconnector switches & bus bars each
4.2 enclosed in bus enclosures running along the length of the switch gear to inter- Nos 1
connect each of circuit breaker bay module. Each busbar set shall be complete
with potential transformer , disconnectors, SF6 gas monitoring system for the
complete bus etc.
XLPE Power Copper conductor cable for the GIS system (36
4.3 KV class) and cable termination kit for Indoor & outdoor
36 KV XLPE 630 SQ. MM single core copper Cable as per tech

4.3.1 spec (for connectivity from 33 KV side of 220/33 KV Transformer to Mtr 600
33 KV GIS panel)
33KV CABLE 300 SQ. MM single core copper as per tech spec (for
33 KV connectivity from GIS equipment to Station Transformer
4.3.2 Mtr 1500
(two nos station trafo) & outgoing feeders upto DP structure end)
36KV Indoor type termination kits (GIS side) suitable for 1CX 630
4.3.3 NOS 3
sq. mm
36 kV Outdoor type termination Kits (33 KV Transformer side)
4.3.4 NOS 3
suitable for 1CX 630 sq. mm
36 kV Indoor type termination Kits (GIS side) suitable for 1CX300
4.3.5 NOS 6
Sq.mm
36 kV Outdoor type termination Kits (33 KV Station Transformer
4.3.6 NOS 6
side) suitable for 1CX300 Sq.mm
4.4 36 KV Bus Post Insulator as per technical specification Nos 9
All type of Terminal clamp & connectors suitable for 36 KV, 1250 A for
4.5 station transformers. LOT 1
All types of HARDWARES & FITTINGS/SPACERS/CLAMPS &

4.6 CONNECTORS FOR 400KV SIDE OF THE GIS S/S. Lot 1
4.7 400 KV LA Clamp as per TS Set 18

4.8 400 KV SI Clamp as per TS Set 4
4.9 CONNECTORS FOR 220 KV SIDE OF THE GIS S/S. Lot 1

220 KV SI Clamp as per TS
4.11 Set 4
4.12 SUBSTATION EARTHING SYSTEMS
EARTHING CONDUCTOR FOR BURRIAL :75x12mm for laying as main
4.12.1 MT 120
eartth mat (spacing maximum 5m both way)
EARTHING CONDUCTOR: 75X 10 mm GI (HDG) Flat for Raiser from
4.12.2 MT 20
the burial earth mat to equipment,structure etc)
EARTHING CONDUCTOR: 50X6mm GI (HDG) Flat for Raiser for
4.12.3 MT 10
console box,LT panels,DC panels,Marshalling boxes etc)
EARTHING DEVICE & ASSOCIATED ACCESSORIES (50 mm heavy
4.12.4 Nos 180
duty GI PERFORATED PIPE 3 mtrs long for treated earth pit)
4.12.5 EARTHING DEVICE & ASSOCIATED ACCESSORIES 40mm MS rod 3 Nos 170
mtrsCable
G.I long for nonincluding
Trays treated earth pit)GI angle suitable for different sections
support
along with its accessories as per TS. Details of No. of tiers are indicated
5
in the TS-Civil Section accordingly the requirement can be ascertained.
G.I Cable Trays(size: 450x75x2500mm)

5.1 MTRS 4500
5.2 G.I Cable Trays(size: 300x75x2500mm) MTRS 4500
5.4 Support G. I angle 50x50x6 mm for cable tray MT 6
SWITCH YARD AC CONSOLE FOR LIGHTING (01 nos each on 400KV
6 side & 220 kv side and other area ) as per Technical Specification. NOS 3
SWITCH YARD RECEPTACLE BOARD FOR TFR OIL FILTERATION

7 NOS 1
(01 no. near 400/220KV ICT) as per Technical Specification.
SWITCH YARD RECEPTACLE BOARD FOR WELDING & OTHER
8 NOS 2
EMERGENCY as per Technical Specification.
HDG SWITCH YARD STRUCTURES (INCLUDING FOUNDATION
9
BOLTS) FOR 400Kv & 220KV CLASS
DIFFERENT TYPES OF LATICE TYPE COLUMNS & DIFFERENT TYPE
9.1
OF BEAMS AND LIGHTING CUM LIGHTNING MAST
9.1.1 TOTAL WEIGHT OF COLUMN & BEAM MT 157
DIFFERENT TYPE OF SUPPORT STRUCTURES (HDG) OF PIPE TYPE
9.2 FOR ALL 400KV, 220KV & 33 KV EQUIPMENT INCLUDING HIGH
LEVEL SA NEAR TRANSFORMER.
TOTAL WEIGHT OF PIPE TYPE SUPPORT STRUCTURE FOR ABOVE
9.2.1 MT 75
EQUIPMENT
40 Mtrs heigh Monopole (HDG) Lighting cum Lightning Mast
including LED lighting fixtures (240 watts each minimum 8 Nos.)
with control gear panel etc suitable for wind zone-V , with all other
9.2.2 Nos 3
accessories like motor for hoisting/lowering the lighting platform &
other switchgear and lighting control panel including required
cable(copper) & other accessories etc.
Total weight of different type of GI Nuts and bolts for the above structures
10 MT 11.60
11 GENERAL EQUIPMENT & SUBSTATION ACCESSORIES
POWER CABLES,1.1KV,XLPE & PVC FRLS ,FLAT STRIP ARMOURED,
11.1
ALUMINIUM CONDUCTOR (As per Specification)
11.1.1 XLPE-3.5 CX185 mm2 Mtrs 500
11.1.2 XLPE-3.5 CX120 mm2 Mtrs 500
11.1.3 PVC-3.5 CX70 mm2 Mtrs 250
11.1.4 PVC-3.5 CX35 mm2 Mtrs 500
11.1.5 PVC-4 CX 16 mm2 Mtrs 1000
11.1.6 PVC-4 CX 6 mm2 Mtrs 1000
11.1.7 PVC-2CX 6 mm2 Mtrs 2000
CONTROL CABLES,1.1 KV,PVC FRLS , COPPER STRANDED
11.2
ARMOURED STRANDED(As per specification).
11.2.1 4 CX 2.5 mm2 Mtrs 6000
11.2.2 5 CX 2.5 mm2 Mtrs 4000
11.2.3 7CX 2.5 mm2 Mtrs 5000
11.2.4 10 CX 2.5 mm2 Mtrs 10000
11.2.5 12 CX 2.5 mm2 Mtrs 5000
11.2.6 16 CX 2.5 mm2 Mtrs 5000
11.2.7 19 CX 2.5 mm2 Mtrs 3000
11.2.8 1CX 120 mm2 BAT TO BAT CHARGER & CHARGER TO DCDB Mtrs 300
HARD CONDUIT INCLUDING of adequate tensile strength minimum
7kg/sqmm or better & ITS ACCESSORIES LIKE ALL TYPE OF
12 LOT 1
SOCKETS & BENDS FOR TAKING CABLE FROM TRENCH TO
EQUIPMENT MB etc
13 ACCESSORIES FOR PLCC SYSTEM With OPGW cable
13.1 48 Fibre Optic Approach cable along with HDPE Pipes KM 1.00
13.2 Optical line Terminal Equipment(OLTE) -STM4 type SDH equipment with No
integrated MUX & tributary cards for speech & data ports for interfacing
1
of Speech & data which should be compatible with existing OPTCL
system
13.3 Digital Teleprotection Equipment and accessories to be suitable for No
1
interfacing with SDHMUX
13.4 Supply of FODP(Fibre Optic Distribution Panel)48 F: Indoor type,rack No
2
mounted with FCPC coupling and pig tails(DWSm Fibre)
13.5 48 V, 300 AH, maintenance free VRLA Battery set. Set 1
13.6
SMPS based Battery Charger of 75A suitable for 48V VRLA Battery set No 1
13.7 2.5 sq. mm muti strand 2 core control cable(power
Metre 600
supply,Transducer/MFT PT supply)
13.8
2.5 sq. mm multi strand 4 core control cable(Transducer/MFT CT supply) Metre 600
13.9 1.5 sq. mm multi strand 10 core control cable(Digital Input) Metre 500
13.10 10 sq. mm 2 core multi strand control cable(Battery) Metre 300
13.11 48V DCDB Set 1
13.12
Earth Flat, Cable Tray, Telephone cable,Foundation rail, Junction Box,. Set 1
SUPPLY OF STATION TRANSFORMER & OTHER MATERIALS FOR

14 MEETING THE AUXILIARY SUPPLY OF THE SUB-STATION AS PER
TECHNICAL SPECIFICATION
STATION TRANSFORMER 33KV/0.43 V,500 KVA (Confirming
14.1 to Energy Efficiency Level 2 -AS PER SPECIFICATION & NOS 2
relevant IS)
One no. 4 pole structure (HDG Type) alongwith other
equipment & materials for two nos station transformers:
1.4 Pole structure (using 200X100 mm RS Joist)
2. Channel & Angle FOR BRACING OF, CHANNEL for the SA &
Isolator & HG fuse etc.
3. 90 KN Disc/composite long rod Insulators for 33 KV (48 nos./12
sets) for bus, Bus stringing using ACSR moose conductor &
tension hardwares,other clamps & connectors etc as per
requirement.
4. 2sets of 33 KV Isolator (800 AMP) for 33 KV side of station trafo.
5. 2sets of 33 KV HG FUSE.
14.2 6. 125 Sq mm AAAC conductor suitable for connection between HG SET 2
fuse & station transformer bushing.
7. 2 sets of LT OUT DOOR KIOSK MADE OUT OF 3mm CRCA
sheet Gl MARSHALLING BOX suitable for outdoor mounting. The
bus bar suitable for 1000 AMP shall be arranged in the out door
kiosk and other Facility like two sets of 400 Amps MCCB for
incoming & outgoing with required sizes of terminal studs for power
cable termination & any other accessories required.
AII materials shall be As per relevant latest IS & as per the direction
of Engg. in charge
SUB STATION LIGHTING (AS PER SPECIFICATION AND APPROVED

15 DRAWINGS )(Switch yard and other street area)(Including provision
of the fittings on the LM)
SUB-STATION SWITCH YARD LIGHTING,IT INCLUDES SUPPLY OF
FIXTURES & LAMPS (LED) of reputed make (Philips/CGL/Bajaj/ any
15.1 other approved make of OPTCL) with switch gear,GI Conduit etc.(Lighting SET 60
fixtures are to be fixed rigidly on the Column at a suitable height so that
the required lux can be achieved).(150 watt each)
STREET LIGHTING: IT INCLUDES SUPPLY OF GI TUBULAR POLE AS
PER TECHNICAL SPECIFICATION, LED LIGHTING FIXTURES including
16 LAMPS of reputed make (Philips/CGL/Bajaj).(100 watt each) for Street
Light. (TO BE PROVIDED IN THE SWITCH YARD, ALONG THE ROADS
(APPROACH INSIDE YARD AND OTHER ROADS).
LED LIGHTING FIXTURES including LAMPS of reputed make
16.1 (Philips/CGL/Bajaj/ any other approved make of OPTCL).(100 watt each) SET 60
for Street Light.
GI Tubular Pole: (410-SP-24: IS 2713-Part-II-1980 or latest) Length of
pole 8.5 mtrs(minimum weight 158 Kgs).
(ALL THE STREET LIGHT POLE SHALL BE OF GI TUBULAR POLE
16.2 AND PROVISION OF A GI JUNCTION BOX WITH SUITABLE COVERS SET 60
AT A HEIGHT OF 1 METRE FROM THE GROUND. THE JUNCTION
BOX SHALL HAVE PROVISION OF FUSES, BUSES, CONNECTORS
FOR CABLE IN AND OUT.
OUTDOOR KIOSK of 3 mm thick CRCA sheet duly hot dip galvanised
16.3 FOR STREET LIGHT HAVING 2 NOS 200 AMP SWITCH FUSE UNITS NO 2
AND 10 NOS. OUT LETS OF 32 AMP MCB.
INDOOR LIGHTING (AS PER SPECIFICATION AND APPROVED
17 DRAWINGS ) (GIS, Control room building,Store shed,store
room,Security room cum Visitors room and other area)
CONTROL ROOM BUILDING INDOOR LIGHTING, IT INCLUDES
SUPPLY OF FIXTURES & LAMPS (LED) of reputed make
(Philips/CGL/Bajaj/ other approved make of OPTCL) with switch
gear,Conduit & other required materials for succesful illumination of the
17.1 LOT 1
area/rooms.( No. of LED Lighting fixtures are to be calculated based on
the illumination design considering the required lux level indicated in the
technical spec & fixing of the same rigidly on the suitable height either
ceiling & wall as required.)
INDOOR LIGHTING OF SECURITY SHED CUM VISITORS
ROOM,PUMP HOUSE,STORE SHED,STORE ROOM, FFPH BUILDING:
IT INCLUDES SUPPLY OF FIXTURES & LAMPS (LED) of reputed make
(Philips/CGL/Bajaj/ other approved make of OPTCL) with switch
17.2 gear,Conduit & other required materials for succesful illumination of the LOT 1
area/rooms.( No. of LED Lighting fixtures are to be calculated based on
the illumination design considering the required lux level indicated in the
technical spec & fixing of the same rigidly on the suitable height either
ceiling & wall as required.)
2 TR CAPACITY SPLIT AIR CONDITIONING UNITS WITH REMOTE

CONTROL FACILITY: INCLUDING SUPPLY OF 5 star rated AIR
CONDITIONERS, Automatic Voltage Stabiliser,CONTROL BOXES ETC
17.3 FOR COMPLETING THE A.C SCHEME.(AS PER SPECIFICATION ) Nos. 20
FOR CONTROL ROOM, CARRIER ROOM & CONFERENCE
ROOM.,OFFICE ROOM etc which includes all type of cables & wires and
a main control switch gear kiosk having sufficient outlet for each air
conditioner unit.
Supply of Smoke & Heat detection system: Addressable optical
Smoke & Heat Multi detector (adequate Nos) for 33KV GIS cum
control room building including all accessories, the Main control
panel (Microprocessor based 2 loop fire alarm control panel
expandable upto 18 loops fully networkable with each loop capable
of taking 99 devices, 8 line x 40 character alpha- numeric liquid
crystal display .The panel shall be soft addressable type . The
panel shall be able to give pin point location of all fire/fault
conditions. Further, the panel must be able to automatically switch
off respective control switches when ever any alarm is triggered.
The panel shall have in built rectifier, Loop cards,provision for
externel & internal printer(if required), L C D unit to indicate
Fire/Fault Signal with address and analog output, built in printer to
17.4 log all fire or fault events complete in all respects, integral SMF lead SET 1
acid batteries with sealed cells of 24 V capable of running for a
minimum of 8 hours with integral battery charger complete as
required and as per specification. The fire alarm panel shall be
suitable for software integration with BMS & PA system ,wall
mounting loop powered addressable type hooter with all
accessories , addressable manual call box made of polycarbonate
with plastic break glass front and complete with monitor module
MCB, addressable isolator module with required PVC box, fittings
and fixtures, wiring with PVC FRLS wire to cover the required for
fire & smoke detection etc. (One control room building is to be
provided with Heat & smoke detection). Should have facility for
integration with SAS.
FIRE FIGHTING SYSTEM(PORTABLE /TROLLEY/ WHEEL

MOUNTEDFIRE EXTINGUSHERS SETS FOR CONTROL
18 ROOM,EQUIPMENT LIKE TRANSFORMER AND OTHER AREAS AS
PER TECH SPEC(REFER TS-VOL-IIA-SCOPE OF WORKAT SL NO. 15-
ANNEXURE - I)
18.1 FOAM TYPE-9 LTRS NOS 4
18.2 DRY CHEMICAL POWDER(TROLLEY MOUNTED)- 22.5 KGS NOS 6
18.3 DRY POWDER TYPE - 5 KGS NOS 6
18.4 CO2 - 4.5 KGS NOS 10
FEEDER PROTECTION PANEL (MAIN-I , MAIN-II & BACK-UP
19.5 PROTECTION WITH AUTO RECLOSURE DISTANCE PROTECTION NOS 4
with Bay control unit (BCU) for substation automation system.
TRANSFORMER PROTECTION PANEL (DIFFERENTIAL I &II , REF I &
II & BACK-UP PROTECTION for HV & IV side CONSIDERING HV ,IV &
19.6 SET 2
LV side for 500 MVA 400/220/33 KV ICT) with Bay control units (BCU) for
substation automation system.
18.7 9 litre water type Nos. 4
18.8 4.5 kg DCP type Nos. 4
18.9 50 Litres Mechanical Foam type Nos. 2
18.10 FIRE BUCKET (6 NOS IN EACH STAND) WITH STAND SET 5
SUBSTATION AUTOMATION SYSTEM FOR 400/220 KV SUBSTATION
ON PRP MODE: Design , engineering , drawing, supervision, installation ,
testing & commissioning of Substation Automation system alongwith
Supply of the following 400,220,and 33 kV level of protection panels
19
consisting of Bay control Units & numerical protection relays and other
auxiliary relays suitable for SAS as per technical specification.
NOTE: All protective relays & BCU shall be numerical type.
Yard AC Kiosk :5000 mm (L)x4000mm (W)x 3300mm (H) with AC, as per
19.1 Nos. 4
the Specification;
Gate way panel for Sub-Station Automation (in PRP as per the
specification & indicative drg ) system (for All 400 , 220 & 33 KV side bays
including the future bays),other accessories (comprising servers, engg.
Station, works station (Main & standby), Remote station control, Colour
Laser jet Printers & dot matrix printer for local station as per requirement
and also for remote station, Ethernet Switches , LIU, Red Box, Multimode
19.2 glass fibre Doublle jacket armoured optical cables, special cables like SET 1
F.O patch cord & armoured FO cables of adequate length etc required for
the system in all respect as per latest IEC 61850 standard, Inverters of
required capacity & rating (3KVA-Input shall be both A.C & D.C and
output shall be A.C) etc as per TS. A Full HD LED screen of 70 inches
for display including all type of accessories & as per technical
specification.
BCU for Substation Auxilliary System (Datas for monitoring of Station AC,
19.3 Station DC, Lighting, Fire fighting, Air conditioning, Diesel generator etc. SET 1
as per the site requirement)
19.4 GPS System with PTP, IRIG-B, SNTP SET 1
400 KV SIDE PROTECTION & OTHER PANELS as per Technical
19.5
specification.
19.5.1 PROTECTION WITH AUTO RECLOSURE DISTANCE PROTECTION NOS 4
19.5.2 SET 2
TIE BREAKER PROTECTION PANEL with Bay control unit (BCU) for
19.5.3 NOS 3
BUS-BAR PROTECTION PANEL ( Including Provision of bus bar
19.5.4 modules for the future bays and to be integrated with the Automation NOS 1
system)
19.6 220 KV SIDE PROTECTION & OTHER PANELS
19.6.2 II & BACK-UP PROTECTION for HV & LV side CONSIDERING HV & LV NOS 1
side for 40 MVA220/33 KV Power Trnsformer) with Bay control units
(BCU)COUPLER
BUS for substation automation PANEL
PROTECTION system. with Bay control unit (BCU) for
19.6.3 NOS 1
BUS-BAR PROTECTION PANEL ( Provision of bus bar modules for the
19.6.4 NOS 1
future bays and to be integrated with the Automation system)
19.7 33 KV SIDE PROTECTION PANELS
33 KV BUS COUPLER PROTECTION Panel with Bay control protection
unit (BCPU) with with all other relays & component required for complete
19.7.1
prtection,control etc as per TS and also suitable for substation automation
No 1
system.
STATION TRANSFORMER PROTECTION PANEL (BACK-UP
PROTECTION CONSIDERING 2X500 KVA 33/0.43 KV ) with
Bay control protection units (BCPU) with with all other relays &
19.7.2 SET 1
component required for complete prtection,control etc as per TS and
also suitable for substation automation system. [2nos. Feeeder bays
in one panel]
20 AC & DC SYSTEM
20.1 AC SYSTEM
MAIN AC DB,(HAVING A 1600 A,50KA,DRAWOUT TYPE ACB WITH 3
O/C,E/F,U/V RELAYING FACILITY and MECH& ELECT INTERLOCK
20.1.1 FACILITY CONSIDERING Main-1,2 & DG INDOOR TYPE AS PER SET 1
SPECIFICATION.(MAIN DB-1,MAIN DB-2 WITH B/C & PROVISION FOR
D.G INCOMING)
ACDB (HAVING 800A MCCB) AS PER SPECIFICATION (AC DB-1,AC
20.1.2 SET 1
DB-2 WITH B/C)
MAIN LIGHTING DISTRIBUTION BOARD (HAVING 250A MCCB AS
20.1.3 SET 1
INCOMER)AS PER SPECIFICATION (WITH DB-1,DB-2 & B/C)
INDOOR LIGHTING DISTRIBUTION BOARD AS PER SPECIFICATION.
20.1.4 SET 1
(WITH DB-1,DB-2 & B/C)
20.1.5 EMERGENCY LIGHTING DISTRIBUTION BOARD SET 1
20.1.6 INDOOR RECEPTACLE BOARD SET 2
20.2 DC SYSTEM
220 V DC BOARD (HAVING 100A DC MCCB AS INCOMER, E/F (EARTH
LEAKAGE), UNDER & OVER VOLTAGE AS PER SPECIFICATION (DC
20.2.1 DB-1,DC DB-2 & B/C). Consider separate source(DC1 & DC 2) to each SET 1
panels & accordingly sufficient nos. of DC output from DB-1 & 2 to be
considered.
20.2.2 220 V DC EMERGENCY DISTRIBUTION BOARD SET 1
20.2.3 BATTERY (645 AH PLANTE TYPE) for 220 V DC SET 2
BATTERY CHARGER FOR 645 AH, 220 V DC (FLOAT & FLOAT CUM
BOOST) (including provision of series dropper diodes with heat sinks &
20.2.4 SET 2
other protection facility at the DC Load terminal end in order to feed 220
V to the load).
DE MINERALISED PLANT of 30 L/Hr FOR MAKING DISTLED WATER
21 SET 1
FOR BATTERY BANKS
PORTABLE ALUMINIUM LADDER EXTENDABLE TYPE OF ADEQUATE
HEIGHT TO BE USED FOR MAINTENANCE OF EQUIPMENT INSIDE
22 NOS 2
SWITCH YARD.(REFER TS-VOL-IIA-SCOPE OF WORKAT SL NO. 19)
CARTWHEEL MOUNTED ALUMINIUM LADDER OF ADEQUATE

23 NOS 1
HEIGHT TO BE USED FOR MAINTENANCE OF EQUIPMENT .
WATER COOLER WITH WATER PURIFIER (with R.O & ultra violet
24 NOS 1
purification system of ISI mark) SYSTEM
MAINTENANCE & TESTING EQUIPMENT (REFER TS-VOL-IIA-16.
Maintenance & Testing Equipment (ANNEXURE-II & ANNEXURE-III)
25 LOT 1
INDICATED IN -SCHEDULE OF REQUIREMENTS OF MAINTENANCE
EQUIPMENT).
SET
26 WALKIE TALKIE SET 2
/PAIR
OFFICE FURNITURE (REFER TS-VOL-IIA-SCOPE OF WORKAT SL
NO. 18 ANNEXURE - IV ,INDICATED IN SCHEDULE OF
27 REQUIREMENTS OFFICE FURNITURE) & PLACING IN CONTROL LOT 1
ROOM,CONFERENCE ROOM,OFFICE ROOMS,LIBRARY,TESTING
LAB,etc.
FIRE FIGHTING EQIPMENT: (Main Pump, Jockey Pump, DG Set cum
Pump, Control Panel for Fire Fighting System, switcyard equipment and
28 buildings. HVW system & hydrant sytsem, complete with all piping, LOT 1
valves, fittings etc inside pump house for Fire protection sytem of
substation) as per the technical spec.
BEST QUALITY &APPROVED MAKE INSULATING MAT (Confirming to
29 IS:15652:2006) TO BE KEPT INFRONT OF ALL PANELS,BOARDS Nos 45
ETC.(2000X1000X3)mm Size
250 KVA outdoor type silent Generator with contro panel having adequate
30 mechanical & electrical protection as per latest IS with Automatic Mains NOS 1
Failure feature as per Technical spec.
220/33 KV 40 MVA Transformer as per Technical specification (inclusive
of all costs towards type test charges, Mandatory spares, Spanners &
31 NOS 1
Special tools, accessories, etc as specified in the Technical specification)
400/220 KV 500 MVA ICT (inclusive of all costs towards type test
charges, Mandatory spares, Spanners & Special tools, Oil storage tank,
Nitrogen Injection system for protection against Fire & Explosion, On line
32 NOS 2
insulating oil drying system , On line Dissolved Gas (Multi-gas) and
Moisture Analyser, accessories, etc as specified in the Technical
specification)
33 EQUIPMENT and MATERIALS for GIS
33.1 ACCESSORIES
SF6 Gas handling plant of adequate capacity as per the Technical
33.1.1 SET 1
specification.
SF6 gas service cart with all accessories as per the Technical
33.1.2 SET 1
specification.
33.2 TESTING EQUIPMENT
33.2.1 GIS testing equipment as per the Technical specification. SET 1
34 ESSENTIAL TOOLS and SPARES for GIS
34.1 SPARES for 420KV GIS
34.1.1 Single phase voltage transformer SET 1
34.1.2 Single phase set of 5 cores current transformer including enclosure SET 1
34.1.3 Enclosure insulators and main circuit of busbar SET 1
34.1.4 Tripping and closing coils SET 3
34.1.5 SF6 Pressure gauges SET 2
34.1.6 SF6 Pressure relief devices SET 2
34.1.7 Auxiliary contacts for circuit breaker SET 1
34.1.8 Auxiliary contacts for DS and ES SET 1
34.1.9 SF6 gas in steel bottle 52 kg / bottle NOS 2
34.1.10 Spring charge motor for circuit breakers UNIT 1
Complete drive mechanism for disconnect switches and grounding
34.1.11 UNIT 1
switches
34.1.12 Motor for disconnect switches and grounding switches UNIT 1
34.1.13 Complete drive mechanism for fast acting grounding switches UNIT 1
34.1.14 Motor for fast acting grounding switches UNIT 1
34.1.15 Rupture disc for circuit breakers / potential transformer NOS 1
Set of spares for local control cabinet including M.C.B., fuses, time relays,
34.1.16 SET 1
auxiliary relays and terminals
34.1.17 Rupture disc for other compartments NOS 2
34.2.10 UNIT 1
switches
34.2.15 SET 1
34.3 SPECIAL TOOLS
34.3.1 SF6 gas leak detector as per the Technical specification. SET 1
34.3.2 SF6 gas analyzer as per the Technical specification. SET 1
34.3.3 Milli volt drop measurement applicance SET 1
34.3.4 One set of Box Spanner SET 1
34.3.5 One set of adjustable Spanner SET 1
34.3.6 SF6 gas bottle locking, measuring and filling assembly with all hose SET 2
34.3.7 One set of pipe grooving tools for the hydraulic operating mechanism SET 1
34.3.8 Infrared camera as per the Technical specification. SET 1
TOTAL OF SUBSTATION-SCHEDULE-1 -Plant (to Schedule No. 6 Grand Summary)
Name of Bidder:_______________________________
Signature of Bidder:_____________________________
1
Bidders shall enter a code representing the country of origin of all imported plant and equipment.
2
Specify currency in accordance with specifications in Bid Data Sheet under ITB 19.1 in Single-Stage Bid, or ITB 34.1 in Two-Stage Bid. Create and use as many
columns for Unit Price and Total Price as there are currencies.
Country of Origin Declaration Form
Item Description Code Country
(Ramkrushnapur),Bhadrak.in Odisha State of India under PACKAGE-3 Under Japan International Cooperation Agency (JICA)’s
ODA Loan.
Schedule No. 2. Plant Supplied from Within the Employer’s Country (Sub-station )
NAME OF THE BIDDER
Out Door type GIS S/S (New):400 KV Bay-

5 Nos.(FDR-2,TFR-2& B/C-1),220 KV Bay-
Quantity for: Construction of 2x500 MVA
400/220/33 GIS S/S at Ramkrushnapur
2 Nos.(FDR-2,TFR-2,B/C-1)
SUPPLY OF FOLLOWING EQUIPMENTS
SL. NO.
(As per Technical Specification)
UNIT Unit Price1 Total Price1
(1) (2) (1) x (3)

3150A, 63kA for 3s, one and half Circuit Breaker (Circuit breaker shall
be E2-C2-M2 class as per IEC 62271-100) arrangement. 420kV
1 OUTDOOR GIS EQUIPMENT as per latest IEC standard & type tested
equipment as per technical specification, with open future proof &
flexible system in line with IEC 61850 & IEC 62271-203.
420kV,3150A, 63KA for 3 sec (Busbar, CB, Disconnector, Grounding
switch, CT & PT), SF6 gas insulated Complete Diameter module (2 Nos
Feeder) each comprising of SF6 gas insulated Single Pole Circuit Breaker
(3 Sets) with CSD (Control Switching Device), Single Phase Current
Transformer (18 Nos), Single Phase Potential Transformer (4 Winding) (6
Nos), Motorised 3 Phase Disconnector (6 Sets), Motorised safety
Grounding switch (8 Nos), Motorised 3 Phase Disconnector with high
speed fault making Motorised Grounding switch (2 Nos), Local Control
Cubicle, SF6 gas monitoring system for complete diameter, SF6 bus duct
1.1 termination arrangement, online PD sensor (adequate number of UHF Set 3
sensors in the offered GIS equipment for detection of Partial discharge (of
Bolts & Washers for Outdoor use, Absorbent,Limit Switch, SF6 Gas, etc.
against any hazardous touch voltages and electro-magnetic interferences)
as per the technical specification.
420kV,3150A, 63KA for 3 sec (Busbar, Disconnector, Grounding Switch &

Bus PT), 3 Phase Isolated, SF6 gas insulated, metal enclosed busbars
Complete Diameter module (2 Nos BUS-PT) in bus enclosures running
along the length of the switchgear to interconnect each of circuit breaker
diameter module. Each busbar set shall be complete with Potential
Transformer (4 Winding), Motorised 3 Phase Disconnector (1 No),
Motorised Busbar safety Grounding switch (1 No), Local Control Cubicle,
SF6 gas monitoring system online PD sensor (adequate number of UHF
1.2 sensors in the offered GIS equipment for detection of Partial discharge (of Set 1
Bolts & Washers for Outdoor use, Absorbent, Limit Switch, SF6 Gas, etc.
420kV, 3150A, 63kA, 3 Sec, Single phase, SF6 gas Insulated Bus Duct
bends, joints, accessories, & its earthing arrangement with earthing strips
1.3 RM 900
etc. as per the technical specification.
420kV, 3150A, 63kA, SF6/Air BUSHING (Bushing shall be of Polymer /
composite insulator type and shall be seamless sheath of a silicone rubber
compound. The hollow silicone composite insulators shall comply as per
1.4 No 18
IEC 61462 and IEC 62217. The design of the composite insulators shall be
tested and verified according to IEC 61462) FOR CONNECTING GIS TO
AIS along with support structure.
420kV GIS equipment system shall have Online continuous Partial
Discharge Monitoring System (PDM) system to provide an automatic
facility for the simultaneous collection of PD data at multiple points on the
GIS & its associated GIB ducts and Voltage Transformers adopting UHF
technique & the data stored shall provide a historical record of the
progress of PD sources and shall identify the areas of maximum activity.
1.5 Set 1
PDM system shall be interfacing with UHF PD couplers provided. The PD
Monitoring PC Work Station along with all accessories shall be considered.
Power supply to PDM PC shall have protection against surges, overload
and short circuit. A dedicated on-line UPS system shall also be provided
as a backup during supply interruption, to ensure trouble-free & reliable
running of the PDM System for a minimum of 15 minutes duration.
3150A, 50kA for 3s, Double Busbar Circuit Breaker (Circuit breaker
shall be E2-C2-M2 class as per IEC 62271-100) arrangement.
245kV OUTDOOR GIS EQUIPMENT as per latest IEC standard & type
2 tested equipment as per technical specification, with open future
proof & flexible system in line with IEC 61850 & IEC 62271-203.
Switch & CT), SF6 gas insulated ICT Feeder Bay Module each comprising
of SF6 gas insulated Single Pole Circuit Breaker (1 Set), Single Phase
Current Transformer (6 Nos), Motorised Busbar 3 Phase Disconnector (2
Nos), Motorised Disconnector (1 No), Motorised safety Grounding switch
(3 Nos), Local Control Cubicle, SF6 gas monitoring system for complete
bay, SF6 bus duct termination arrangement (3 Nos), PD sensor (adequate
2.1 Partial discharge (of 5 pC and above) as per IEC 60270 through Partial Set 3
SF6 Gas, etc. to complete ICT Feeder Bay Module & its earthing

switch, CT & PT), SF6 gas insulated Line Feeder Bay Module each
comprising of SF6 gas insulated Single Pole Circuit Breaker (1 Set), Single
Phase Current Transformer (6 Nos), Single phase Line Potential
Transformer (4 winding) (3 Nos), Motorised 3 Phase Busbar Disconnector
(2 Nos), Motorised safety Grounding switch (2 Nos), Motorised 3 Phase
Disconnector with high speed fault making Motorised Grounding switch (1
No), Local Control Cubicle, SF6 gas monitoring system for complete bay,
SF6 bus duct termination arrangement (3 Nos), PD sensor (adequate
2.2 Set 4
SF6 Gas, etc. to complete Line Feeder Bay Module & its earthing
245kV, 3150A, 50kA for 3 sec (Busbars, Disconnector, Grounding switch
& bus PT), 1 Phase Isolated Bus-PT Bay Module comprisig of SF6 gas
insulated metal enclosed busbars each enclosed in bus enclosures
running along the length of the switchgear to interconnect each of circuit
breaker bay module. Each busbar set shall be complete with Single phase
bus Potential Transformer (4 winding) (3 Nos), Motorised 3 Phase
Disconnector (1 No) , Motorised Busbar safety Grounding switch (1 No),
Local Control Cubicle, SF6 gas monitoring system PD sensor (adequate
2.3 number of UHF sensors in the offered GIS equipment for detection of Set 1
SF6 Gas, etc. to complete the bus & its earthing arrangement with earthing
245kV, 3150A, 50kA for 3 sec (CB, Disconnector, Grounding switch & CT),
SF6 gas insulated Bus Coupler Bay Module comprising of SF6 gas
insulated Single Pole Circuit Breaker (1 Set), Single Phase Current
Transformer (6 Nos), Motorised 3 Phase Disconnector (2 Nos), Motorised
safety Grounding switch (2 Nos), Local Control Cubicle, SF6 gas
monitoring system, PD sensor (adequate number of UHF sensors in the
offered GIS equipment for detection of Partial discharge (of 5 pC and
2.4 above) as per IEC 60270 through Partial Discharge (PD) monitoring Set 1
system), different gas compartment, O-ring & gaskets, Nuts, Bolts &
Washers for Outdoor use, Absorbent, Limit Switch, SF6 Gas, etc. to
complete Bus Coupler Bay Module & its earthing arrangement with
operating staff against any hazardous touch voltages and electro-magnetic
245kV, 3150A, 50 kA, 3 sec, single phase, SF6 gas Insulated Bus Duct
bends, joints,accessories, & its earthing arrangement with earthing strips
2.5 RM 1000
245kV,3150A, 50kA SF6/Air BUSHING (Bushing shall be of Polymer /
composite insulator type and shall be seamless sheath of a silicone rubber
compound. The hollow silicone composite insulators shall comply as per
2.6 No 21
IEC 61462 and IEC 62217. The design of the composite insulators shall be
tested and verified according to IEC 61462) FOR CONNECTING GIS TO
AIS along with support structure.
245kV system shall have Portable Partial Discharge Monitoring System
(PDM) & shall be capable for measuring PD in charged GIS environment,
bandwidth in order of 100MHz–2GHz & provision to select a wide range of
intermediate bandwidths and the principle of operation shall be based on
2.7 UHF principle of detection. The Detection and measurement of PD and Set 1
bouncing particles having in built large coloured LCD for displaying and
storing facility in the instrument for further analysis to locate actual source
of PD such as free conducting particles, floating components, voids in
spacers, particle on spacer surfaces etc.
3.2 NOS 6
specification.
3.4 NOS 6
specification.
400KV metal oxide surge arrrestor, 20 KA , Long duration discharge class
3.5 NOS 18
IV , 12KJ/KV at 336KV as per technical specification.
216KV metal oxide surge arrrestor, 10KA Long duration discharge class III
3.6 NOS 21
, 10 KJ/KV at 216KV as per technical specification.
30 KV, METAL OXIDE SURGE ARRESTOR, 10kA, Long duration
3.7 NOS 9
discharge class III (AIS) as per technical specification.
36 KV ,1250A, 31.5 KA for 1 sec, isolator (single isolator with earth switch)
3.8 SET 2
including post insulators as per technical specification
36KV, 1250A, 31.5kA for 3 sec, SF6 gas insulated transformer bay module
each comprising of SF6 gas insulated Vacuum circuit breaker , current
transformer , bus-bar disconnectors with common grounding switch , SF6 gas
4.1 SET 3
monitoring system for complete bay (having 33 KV Bus Bar of 2000 Amp) to
complete transformer bay module suitable for cable connection to transformer.
36KV, 1250A , 31.5kA for 3 sec, (33 KV Bus Bar 2000 Amp) SF6 gas
insulated bus-coupler bay module comprising of SF6 gas insulated vacuum circuit
breaker , current transformer , disconnector switches & bus bars each enclosed in
4.2 bus enclosures running along the length of the switch gear to inter-connect each of Nos 1
circuit breaker bay module. Each busbar set shall be complete with potential
transformer , disconnectors, SF6 gas monitoring system for the complete bus etc.
XLPE Power Copper conductor cable for the GIS system (36
4.3
KV class) and cable termination kit for Indoor & outdoor
36 KV XLPE 630 SQ. MM single core copper Cable as per tech
4.3.1 spec (for connectivity from 33 KV side of 220/33 KV Transformer to Mtr 600
33 KV GIS panel)
33KV CABLE 300 SQ. MM single core copper as per tech spec
(for 33 KV connectivity from GIS equipment to Station Transformer
4.3.2 Mtr 1500
(two nos station trafo) & outgoing feeders upto DP structure end)
36KV Indoor type termination kits (GIS side) suitable for 1CX 630
4.3.3 NOS 3
sq. mm
36 KV Cable termination kit including Cable to Air Bushing suitable for
4.3.4 outdoor for 33 KV side of Transformer suitable for 1CX630 Sqmm copper cable. NOS 3
36 kV Indoor type termination Kits (GIS side) suitable for 1CX300

4.3.5 NOS 6
Sq.mm
33 KV Cable termination kit including Cable to Air Bushing suitable for
4.3.6 NOS 6
outdoor for 33 KV suitable for 1CX300 Sqmm copper cable.
4.4 36 KV Bus Post Insulator as per technical specification Nos 9
All type of Terminal clamp & connectors suitable for 36 KV, 1250 A for
4.5 LOT 1
station transformers.


4.12 SUBSTATION EARTHING SYSTEMS
4.12.1 MT 120
EARTHING CONDUCTOR: 75X 10 mm GI (HDG) Flat for Raiser from the
4.12.2 burial earth mat to equipment,structure etc) MT 20
EARTHING CONDUCTOR: 50X6mm GI (HDG) Flat for Raiser for

4.12.3 MT 10
console box,LT panels,DC panels,Marshalling boxes etc)
EARTHING DEVICE & ASSOCIATED ACCESSORIES (50 mm heavy duty
4.12.4 Nos 180
GI PERFORATED PIPE 3 mtrs long for treated earth pit)
EARTHING DEVICE & ASSOCIATED ACCESSORIES 40mm MS rod 3
4.12.5 Nos 170
mtrs long for non treated earth pit)
G.I Cable Trays including support GI angle suitable for different sections
5 along with its accessories as per TS. Details of No. of tiers are indicated in
the TS-Civil Section accordingly the requirement can be ascertained.
6 NOS 3
side & 220 kv side and other area ) as per Technical Specification.
SWITCH YARD RECEPTACLE BOARD FOR TFR OIL FILTERATION
7 NOS 1
(01 no. near 400/220KV ICT) as per Technical Specification.
8 NOS 2
9
BOLTS) FOR 400Kv & 220KV CLASS
9.1
9.2 FOR ALL 400KV, 220KV & 33 KV EQUIPMENT INCLUDING HIGH LEVEL
SA NEAR TRANSFORMER.
9.2.1 MT 75
EQUIPMENT
40 Mtrs heigh Monopole (HDG) Lighting cum Lightning Mast
including LED lighting fixtures (240 watts each minimum 8 Nos.)
with control gear panel etc suitable for wind zone-V , with all other
9.2.2 Nos 3
accessories like motor for hoisting/lowering the lighting platform &
other switchgear and lighting control panel including required
cable(copper) & other accessories etc.
10 MT 11.60
11 GENERAL EQUIPMENT & SUBSTATION ACCESSORIES
11.1
ALUMINIUM CONDUCTOR (As per Specification)
11.1.1 XLPE-3.5 CX185 mm2 Mtrs 500
11.1.2 XLPE-3.5 CX120 mm2 Mtrs 500
11.1.3 PVC-3.5 CX70 mm2 Mtrs 250
11.1.4 PVC-3.5 CX35 mm2 Mtrs 500
11.1.5 PVC-4 CX 16 mm2 Mtrs 1000
11.1.6 PVC-4 CX 6 mm2 Mtrs 1000
11.1.7 PVC-2CX 6 mm2 Mtrs 2000
11.2 ARMOURED STRANDED(As per specification). [The cable quatities are
tentative. The same shall be supplied as per Cable schedule quantity]
11.2.1 4 CX 2.5 mm2 Mtrs 6000
11.2.2 5 CX 2.5 mm2 Mtrs 4000
11.2.3 7CX 2.5 mm2 Mtrs 5000
11.2.4 10 CX 2.5 mm2 Mtrs 10000
11.2.5 12 CX 2.5 mm2 Mtrs 5000
11.2.6 16 CX 2.5 mm2 Mtrs 5000
11.2.7 19 CX 2.5 mm2 Mtrs 1000
7kg/sqmm or better & ITS ACCESSORIES LIKE ALL TYPE OF SOCKETS
12 LOT 1
& BENDS FOR TAKING CABLE FROM TRENCH TO EQUIPMENT MB
etc
13.1 48 Fibre Optic Approach cable along with HDPE Pipes KM 1.00
13.2 Optical line Terminal Equipment(OLTE) -STM4 type SDH equipment with No
integrated MUX & tributary cards for speech & data ports for interfacing of
1
Speech & data which should be compatible with existing OPTCL system
13.3 Digital Teleprotection Equipment and accessories to be suitable for No
1
interfacing with SDHMUX
13.4 Supply of FODP(Fibre Optic Distribution Panel)48 F: Indoor type,rack No
2
mounted with FCPC coupling and pig tails(DWSm Fibre)
13.6
SMPS based Battery Charger of 75A suitable for 48V VRLA Battery set No 1
13.7 2.5 sq. mm muti strand 2 core control cable(power supply,Transducer/MFT
Metre 600
PT supply)
13.8
2.5 sq. mm multi strand 4 core control cable(Transducer/MFT CT supply) Metre 600
13.11 48V DCDB Set 1
13.12
Earth Flat, Cable Tray, Telephone cable,Foundation rail, Junction Box,. Set 1
STATION TRANSFORMER 33KV/0.43 V,500 KVA (Confirming
14.1 to Energy Efficiency Level 2 -AS PER SPECIFICATION & NOS 2
relevant IS)
One no. 4 pole structure (HDG Type) alongwith other
equipment & materials for two nos station transformers:
2. Channel & Angle FOR BRACING OF, CHANNEL for the SA &
Isolator & HG fuse etc.
3. 90 KN Disc/composite long rod Insulators for 33 KV (48 nos./12
sets) for bus, Bus stringing using ACSR moose conductor &
tension hardwares,other clamps & connectors etc as per
requirement.
4. 2sets of 33 KV Isolator (800 AMP) for 33 KV side of station
trafo.
14.2 5. 2sets of 33 KV HG FUSE. SET 2
6. 125 Sq mm AAAC conductor suitable for connection between
HG fuse & station transformer bushing.
7. 2 sets of LT OUT DOOR KIOSK MADE OUT OF 3mm CRCA
sheet Gl MARSHALLING BOX suitable for outdoor mounting. The
bus bar suitable for 1000 AMP shall be arranged in the out door
kiosk and other Facility like two sets of 400 Amps MCCB for
incoming & outgoing with required sizes of terminal studs for
power cable termination & any other accessories required.
AII materials shall be As per relevant latest IS & as per the
direction of Engg. in charge

15 DRAWINGS )(Switch yard and other street area)(Including provision
of the fittings on the LM)
SUB-STATION SWITCH YARD LIGHTING,IT INCLUDES SUPPLY OF
FIXTURES & LAMPS (LED) of reputed make (Philips/CGL/Bajaj/ any other
15.1 approved make of OPTCL) with switch gear,GI Conduit etc.(Lighting SET 60
fixtures are to be fixed rigidly on the Column at a suitable height so that the
required lux can be achieved).(150 watt each)
STREET LIGHTING: IT INCLUDES SUPPLY OF GI TUBULAR POLE AS
PER TECHNICAL SPECIFICATION, LED LIGHTING FIXTURES including
16 LAMPS of reputed make (Philips/CGL/Bajaj).(100 watt each) for Street
Light. (TO BE PROVIDED IN THE SWITCH YARD, ALONG THE ROADS
(APPROACH INSIDE YARD AND OTHER ROADS).
LED LIGHTING FIXTURES including LAMPS of reputed make
16.1 (Philips/CGL/Bajaj/ any other approved make of OPTCL).(100 watt each) SET 60
for Street Light.
GI Tubular Pole: (410-SP-24: IS 2713-Part-II-1980 or latest) Length of pole
8.5 mtrs(minimum weight 158 Kgs).
AT A HEIGHT OF 1 METRE FROM THE GROUND. THE JUNCTION
BOX SHALL HAVE PROVISION OF FUSES, BUSES, CONNECTORS
FOR CABLE IN AND OUT.
OUTDOOR KIOSK of 3 mm thick CRCA sheet duly hot dip galvanised
16.3 FOR STREET LIGHT HAVING 2 NOS 200 AMP SWITCH FUSE UNITS NO 2
AND 10 NOS. OUT LETS OF 32 AMP MCB.
INDOOR LIGHTING (AS PER SPECIFICATION AND APPROVED
17 DRAWINGS ) (GIS, Control room building,Store shed,store
room,Security room cum Visitors room and other area)
CONTROL ROOM BUILDING INDOOR LIGHTING, IT INCLUDES
SUPPLY OF FIXTURES & LAMPS (LED) of reputed make
(Philips/CGL/Bajaj) with switch gear,Conduit & other required materials for
succesful illumination of the area/rooms.( No. of LED Lighting fixtures are
17.1 LOT 1
to be calculated based on the illumination design considering the required
lux level indicated in the technical spec & fixing of the same rigidly on the
suitable height either ceiling & wall as required.)
INDOOR LIGHTING OF SECURITY SHED CUM VISITORS

ROOM,PUMP HOUSE,STORE SHED,STORE ROOM, FFPH BUILDING:
IT INCLUDES SUPPLY OF FIXTURES & LAMPS (LED) of reputed make
(Philips/CGL/Bajaj) with switch gear,Conduit & other required materials for
17.2 succesful illumination of the area/rooms.( No. of LED Lighting fixtures are LOT 1
to be calculated based on the illumination design considering the required
lux level indicated in the technical spec & fixing of the same rigidly on the
suitable height either ceiling & wall as required.)
17.3 FOR COMPLETING THE A.C SCHEME.(AS PER SPECIFICATION ) Nos. 20
FOR CONTROL ROOM, CARRIER ROOM & CONFERENCE
ROOM.,OFFICE ROOM etc which includes all type of cables & wires and a
main control switch gear kiosk having sufficient outlet for each air
conditioner unit.
Supply of Smoke & Heat detection system: Addressable optical
Smoke & Heat Multi detector (adequate Nos) for 33KV GIS cum
control room building including all accessories, the Main control
panel (Microprocessor based 2 loop fire alarm control panel
expandable upto 18 loops fully networkable with each loop capable
of taking 99 devices, 8 line x 40 character alpha- numeric liquid
crystal display .The panel shall be soft addressable type . The
panel shall be able to give pin point location of all fire/fault
conditions. Further, the panel must be able to automatically switch
off respective control switches when ever any alarm is triggered.
The panel shall have in built rectifier, Loop cards,provision for
externel & internal printer(if required), L C D unit to indicate
Fire/Fault Signal with address and analog output, built in printer to
17.4 log all fire or fault events complete in all respects, integral SMF SET 1
lead acid batteries with sealed cells of 24 V capable of running for
a minimum of 8 hours with integral battery charger complete as
required and as per specification. The fire alarm panel shall be
suitable for software integration with BMS & PA system ,wall
mounting loop powered addressable type hooter with all
accessories , addressable manual call box made of polycarbonate
with plastic break glass front and complete with monitor module
MCB, addressable isolator module with required PVC box, fittings
and fixtures, wiring with PVC FRLS wire to cover the required for
fire & smoke detection etc. (One control room building is to be
provided with Heat & smoke detection). Should have facility for
integration with SAS.
ANNEXURE - I)
18.4 CO2 - 4.5 KGS NOS 10
18.5 CO2 - 9 KGS NOS 10
18.6 CO2 (TROLLY MOUNTED)- 22.5 KGS NOS 4
SUBSTATION AUTOMATION SYSTEM FOR 400/220 KV SUBSTATION
ON PRP MODE: Design , engineering , drawing, supervision, installation ,
testing & commissioning of Substation Automation system alongwith
Supply of the following 400,220,and 33 kV level of protection panels
19
consisting of Bay control Units & numerical protection relays and other
auxiliary relays suitable for SAS as per technical specification.
Yard AC Kiosk :5000 mm (L)x4000mm (W)x 3300mm (H) with AC, as per
19.1 Nos. 4
the Specification;
Gate way panel for Sub-Station Automation (in PRP as per the
specification & indicative drg ) system (for All 400 , 220 & 33 KV side bays
including the future bays),other accessories (comprising servers, engg.
Station, works station (Main & standby), Remote station control, Colour
Laser jet Printers & dot matrix printer for local station as per requirement
and also for remote station, Ethernet Switches , LIU, Red Box, Multimode
19.2 glass fibre Doublle jacket armoured optical cables, special cables like F.O SET 1
patch cord & armoured FO cables of adequate length etc required for the
system in all respect as per latest IEC 61850 standard, Inverters of
required capacity & rating (3KVA-Input shall be both A.C & D.C and output
shall be A.C) etc as per TS. A Full HD LED screen of 70 inches for
display including all type of accessories & as per technical specification.
BCU for Substation Auxilliary System (Datas for monitoring of Station AC,
19.3 Station DC, Lighting, Fire fighting, Air conditioning, Diesel generator etc. as SET 1
per the site requirement)
400 KV SIDE PROTECTION & OTHER PANELS as per Technical
19.5
specification.
19.5.2 SET 2
TIE BREAKER PROTECTION PANEL with Bay control unit (BCU) for
19.5.3 NOS 3
BUS-BAR PROTECTION PANEL ( Including Provision of bus bar
19.5.4 modules for the future bays and to be integrated with the Automation NOS 1
system)
II & BACK-UP PROTECTION for HV & LV side CONSIDERING HV & LV
19.6.2 NOS 1
side for 40 MVA220/33 KV Power Trnsformer) with Bay control units
(BCU) for substation automation system.
BUS COUPLER PROTECTION PANEL with Bay control unit (BCU) for
19.6.3 NOS 1
BUS-BAR PROTECTION PANEL ( Provision of bus bar modules for the
19.6.4 NOS 1
future bays and to be integrated with the Automation system)
33 KV BUS COUPLER PROTECTION Panel with Bay control protection
unit (BCPU) with with all other relays & component required for complete
19.7.1
prtection,control etc as per TS and also suitable for substation automation
No 1
system.
PROTECTION CONSIDERING 2X500 KVA 33/0.43 KV ) with
Bay control protection units (BCPU) with with all other relays &
19.7.2 SET 1
component required for complete prtection,control etc as per TS and
also suitable for substation automation system. [2nos. Feeeder bays
in one panel]
20 AC & DC SYSTEM
20.1 AC SYSTEM
D.G INCOMING)
ACDB (HAVING 800A MCCB) AS PER SPECIFICATION (AC DB-1,AC DB-
20.1.2 SET 1
2 WITH B/C)
20.1.3 SET 1
20.1.4 SET 1
(WITH DB-1,DB-2 & B/C)
20.2 DC SYSTEM
considered.
20.2.4 SET 2
other protection facility at the DC Load terminal end in order to feed 220 V
to the load).
21 SET 1
FOR BATTERY BANKS
22 NOS 2
23 NOS 1
24 NOS 1
25 LOT 1
EQUIPMENT).
SET
26 WALKIE TALKIE SET 2
/PAIR
OFFICE FURNITURE (REFER TS-VOL-IIA-SCOPE OF WORKAT SL
NO. 18 ANNEXURE - IV ,INDICATED IN SCHEDULE OF
27 REQUIREMENTS OFFICE FURNITURE) & PLACING IN CONTROL LOT 1
ROOM,CONFERENCE ROOM,OFFICE ROOMS,LIBRARY,TESTING
LAB,etc.
FIRE FIGHTING EQIPMENT: (Main Pump, Jockey Pump, DG Set cum
Pump, Control Panel for Fire Fighting System, switcyard equipment and
buildings. HVW system & hydrant sytsem, complete with all piping, valves,
28 LOT 1
fittings etc inside pump house for Fire protection sytem of substation) as
per the technical spec.

30 mechanical & electrical protection as per latest IS with Automatic Mains NOS 1
Failure feature as per Technical spec.
220/33 KV 40 MVA Transformer as per Technical specification (inclusive
of all costs towards type test charges, Mandatory spares, Spanners &
31 NOS 1
Special tools, accessories, etc as specified in the Technical specification)
400/220 KV 500 MVA ICT (inclusive of all costs towards type test charges,
Mandatory spares, Spanners & Special tools, Oil storage tank, Nitrogen
Injection system for protection against Fire & Explosion, On line insulating
32 NOS 2
oil drying system , On line Dissolved Gas (Multi-gas) and Moisture
Analyser, accessories, etc as specified in the Technical specification)
33 EQUIPMENT and MATERIALS for GIS

33.1 ACCESSORIES
SF6 Gas handling plant of adequate capacity as per the Technical
33.1.1 SET 1
specification.
SF6 gas service cart with all accessories as per the Technical
33.1.2 SET 1
specification.
33.2 TESTING EQUIPMENT
33.2.1 GIS testing equipment as per the Technical specification. SET 1
34 ESSENTIAL TOOLS and SPARES for GIS
34.1.9 SF6 gas in steel bottle 52 kg / bottle NOS 2
34.1.11 UNIT 1
switches
34.1.16 SET 1
34.2.10 UNIT 1
switches
34.2.15 SET 1
34.3 SPECIAL TOOLS
34.3.1 SF6 gas leak detector as per the Technical specification. SET 1
34.3.2 SF6 gas analyzer as per the Technical specification. SET 1
34.3.3 Milli volt drop measurement applicance SET 1
34.3.4 One set of Box Spanner SET 1
34.3.5 One set of adjustable Spanner SET 1
34.3.6 SF6 gas bottle locking, measuring and filling assembly with all hose SET 2
34.3.7 One set of pipe grooving tools for the hydraulic operating mechanism SET 1
34.3.8 Infrared camera as per the Technical specification. SET 1
TOTAL OF SUBSTATION-SCHEDULE-2 -Plant (to Schedule No. 6 Grand Summary)
Name of
Bidder:_______________________________
Signature of
Bidder:_____________________________
1
Prices of Items quoted in Schedule No.1 shall not be quoted again in Schedule No. 2 and shall have a remark against the said row "Quoted
in Schedule No.-1".
(Ramkrushnapur),Bhadrak.in Odisha State of India under PACKAGE-3 Under Japan International Cooperation Agency (JICA)’s ODA
Loan.
Loan Agreement No: [ID-P245] - FB No: [CPC/JICA/ICB/03/18-19]- Reference Identification No: [OPTCL/JICA/PKG-3]
Schedule No. 4. Installation and Other Services (Sub-station )
NAME OF THE BIDDER
Quantity for: Construction of 2x500

1 1
Ramkrushnapur Out Door type GIS

S/S (New):400 KV Bay-5 Nos.(FDR-
Unit Price Total Price
2,TFR-2& B/C-1),220 KV Bay-2

MVA 400/220/33 GIS S/S at
Nos.(FDR-2,TFR-2,B/C-1)
ERECTION,TESTING & COMMISSIONING OF FOLLOWING Foreign Local Foreign
SL. NO. UNIT Local Currency
EQUIPMENT/MATERIALS ALONG WITH CIVIL WORKS (As per Currency Currency Currency
Technical Specification) Portion
Portion Portion Portion
1 2 3 (1x2) (1x3)
PART A CIVIL WORKS
1 CONTOUR SURVEY,AND LEVELING, BACK FILLING
Contour survey and furnishing contour map including supply of all
1.1 materials, Labour and T&P SQ.MTRS. 55000
Soil investigation : Supply of labour,T&Pand other necessary arrangements

for Soil investigation/testing of the Switchyard,control Room, Quarters area
etc.as per the site requirement,Technical specification & instruction of PER
1.2 5
Engineer-in-Charge. POINT
Cutting, Filling and Levelling of Sub-station area including supply of

2 labour and T&P
LEVELLING OF S/S AREA: Providing, neatly dressing up and levelling of
substation area including switchyard area to a required level as decided by
the Engineer in Charge, the work includes removal, clearing of the entire
area from vegetation, trees, bushes, uprooting of plants and disposal of
surplus earth and unusable material from the site by means of any
2.1 mechanical transport, if required as per direction of the Project In charge,
with all labours, tools, tackles and plants complete as per approved
drawing and specification. This also includes excavation in all type of soils
or rocks, back filling and disposal of excess earth or rocks to make the
area to a level for construction as per scope and as per approved drawing
and specification.
2.1.1 CUTTING of substation area
2.1.1.1 [i]Soft/loose soil CUM 10000
FILLING of substation area with borrowed earth with supply of all labour,T
2.2 & P.
2.2.1 (i) Beyond 30 mtr & up to 100mtr lead CUM 3000

2.2.2 (ii) Beyond 100mtr lead CUM 70000
Foundations : Design, engineering, supply of all labour, material
(Cement-OPC-43 Grade, MS Rod, coarse and fine aggregates(Sand
and Metal Chips) etc.) for construction of RCC ( 1:1.5:3) & PCC (1:3:6),
RCC footings of any depth, pedestal and piling as per requirement
including soil investigation, excavation, concreting, shuttering,
grouting, underpinning and back filling of foundations etc. complete
3 for the following switch yard gantry/ portal structures and equipment
support & others as per the technical specification and approved
drawings.(RCC RATIO 1:1.5:3). This also includes excavation in all
types of soil or rocks, back filling and disposal of excess earth as per
the direction of Engineer In charge.
EXCAVATION FOR PREPARATION OF FOUNDATION WORK FOR THE

SWITCHYARD COLUMN,EQUIPMENT etc.:This also includes excavation
3.1 in all types of soil or rocks,back filling,and disposal of excess earth as per
the direction of Engineer In charge.
3.1.1 Normal Soil(SOFT/LOOSE) Cum 7000

3.1.2 Hard Soil Cum 3000
3.1.3 Soft Rock Cum 700
3.1.4 Hard Rock required blasting Cum 300
Design, Engineering, Providing and laying of plain cement concrete (PCC
1:3:6) of grade M10 with approved quality coarse aggregates (Nominal size
12mm to 20mm) , fine aggregates, cement in column and equipment
3.2 foundation as blind layer inclusive of labour charges for concrete mixing & Cum 500
curing. This includes supply of all labourers, T&P and dewatering wherever
required as per Technical specification and instruction of Engineer In
charge.
Open cast foundation for the above column/equipment/marshalling box
foundations with RCC: 1:1.5:3 (Grade M-20), in the foundation pit as
required for the above foundations) and including supply of Labour all
3.3 materials like ,Cement, coarse and fine aggregates, shuttering, proper Cum 5000
curing of the foundations/concrete and T&P in line with the Specification
and as per direction of Engineer in Charge.
Supply of Steel (FE 500 grade or above) of different size (as per design)
with cutting, bending, binding in position of M.S.Rod for reinfocement of
3.4 foundation concrete of Piles(Under reem Pile) including supply of binding MT. 280
wire (With supply of steel rod ( TATA/RINL/SAIL make)
Cable Trenches: Design, engineering, and construction of RCC cable trenches
and all associated works for cable trench and cable trench crossings as per
technical specifications and approved drawings and as per direction of the
Engineer in Charge.
(1) This also includes excavation in all types of soil or rocks,back filling,and
disposal of excess earth as per the direction of Engineer In charge.
(2) Design, Engineering, Providing and laying of plain cement concrete (PCC
1:3:6) of grade M10 with approved quality coarse aggregates (Nominal size 12mm
to 20mm) , fine aggregates, cement in cable trench as blind layer inclusive of
labour charges for concrete mixing & curing. This includes supply of all labourers,
T&P and dewatering wherever required as per Technical specification and
instruction of Engineer In charge.
(3) Open cast foundation for the cable trench with RCC: 1:1.5:3 (Grade M-20
Nominal mixing),including supply of Labour all materials like MS Rod,Cement,
4 coarse and fine aggregates,shuttering,cutting,bending,binding of M.S.Rod
including supply of binding wire proper curing of the foundations/concrete and
T&P in line with the Specification and as per direction of Engineer in Charge.
(4) Fly ash Brickwork with fly ash Fly ash Brick ,plastering (!:6 Ratio) & curing,
wherever required including the supply of labour,material, cement, etc.
(5)Fabrication & Fixing of MS Angle(G.I) for cable tray support (as per
specification). The cable tray support frame shall be pre fabricated GI angle as
per requirement and to be welded with the plate fixed on the trench wall for better
rigidity. The plate (6mm) fixed on the wall are also to be welded with the MS rods
provided for the trench wall before concreting.
(6) Precast of RCC covers (1:1.5:3) and its fixing on the cable trench as per spec
and instruction of Engg. In Charge.
(7) CABLE TRENCHES INSIDE THE CONTROL ROOM SHALL BE COVERED
WITH M.S CHEQUERED PLATE(Duly painted as per instruction of Engg in
charge) INCLUDING STANDARD SUPPORT STAND {HD Galvanised (M.S
JOIST
Cable ,CHANNEL,ANGLE)}.
trench with covers
4.1
4.1.1 Section 1-1 Mtrs 450
4.1.2 Section 2- 2 Mtrs 600
Rain water harvesting system as per Technical specification and approval
of drawing and as per the direction of the Engineer in charge.
5 LOT 1
Cable trench crossing:Design,engineering,construction including supply of
labour,materials,cement,reinforcement steel,formwork etc,and all
6
associated works for construction of trench crossing as per technical
specification and approved drawing.
6.1 Road crossing for
6.1.1 Section 1-1 Lot 1
6.1.2 Section 2- 2 Lot 1
6.1.3 Section 3-3 Lot 1
CONTROL ROOM BUILDING WITH RAMP: Design, engineering and
construction of switch yard buildings including the cost of all type of
materials, supply of labour, cement, reinforcement- steel, form work and
excavation as per the approved drawing and technical specification. The
column foundations shall be either shallow/open cast type or pile
type foundation as per the site requirement (The RCC structure frame
should be in the ratio 1:1.5:3).This also includes excavation in all types of
soil or rocks,back filling,and disposal of excess earth as per the direction of
Engineer In charge. As per approved drawings and specification. This work
including anti-termite treatment, plinth protection, DPC, peripheral drains,
7 water supply, plumbing, sanitation, fire-fighting, electrification etc
(one Double storied building having the GF: 33KV GIS Room with HT
cable vault room, Store room,Bat room,Maint room, ACDB & DCDB
Room, Toilets & stair case & etc, FF : SAS room, conference room,Office
room,Transit rest room,toilets,pantry etc).
Control Room Building Size: 25 mtrs X 15 Mtrs
The contractor shall finalize the dimensions of the hall & rooms according
to the equipment offered by them providing enough space & access for
erection, operation and maintenance & future expansion.
RCC work including MS rods(FE500 and above grade) (including

7.1 excavation, PCC, Shuttering, etc. for column ,Beams and roofs etc) as per Lot 1
technical spec & approved drawings.
Fly ash brick masonry work in cement sand mortar 1: 6 with Fly ash bricks
7.2 of class designation 75 as per technical spec & approved drawings. Lot 1
Flooring with double charged vitrified tiles with dado in all the rooms,Bath
and toilets shall be provided with anti skid ceramic tiles(wall of the same
7.3 also to be provided with ceramic tiles),Acid proof industrial tiles to be Lot 1
provided on the floor and wall of the battery room as per technical spec &
approved drawings.
External and internal wall painting with primer coat as per technical spec
mentioned in the civil section. External: One coat weather coat primer +
two coats of weather coat colour paint.
7.4 Internal: Two coats wall putty+solvent thinable white primer of one Lot 1
coat+two coats colour paint.
Battery Room:The left over portion of walls and ceiling of Battery room shall
be acid proof paints as per specification & approved drawings.
External and internal wall (External (18mm thk ) and internal (12 mm thk) wall and
ceiling plastering as per technical spec mentioned in the civil section) and Building
7.5 internal & external & ceiling paintings as per technical spec mentioned in the civil Lot
section. The ceiling of Battery room shall be acid proof paints as per specification
& approved drawings.
Provision of ceiling in the control room area as per specification mentioned
7.6 Lot 1
in the civil section & approved drawings.
Doors and windows shall be of sliding type with locking facility and shall be of
aluminium with glaze of 6mm & windows shall have aluminium grills. Windows
7.7 shall be provided with vertical window blinder to protect from the sun ray. As per Lot 1
technical spec & approved drawing.
Provision of PHD and other fittings of reputed make for the control room building
(in Toilets,wash room,overhead water tank of adequate capacity etc) of reputed
make,provision of rain water discharge pipes at different locations and etc as per
requirement and approved drawing. There shall be septic tank and soak pit of
required capacity including complete sewage system as per approved drawing &
technical specification & as per instruction of Engg- in-Charge. It includes supply
of all types of materials of reputed make, labour etc to complete the work. Toilets
7.8 Lot 1
for Gents & Ladies to be provided including all good quality reputed fittings as per
technoical specification. The toilets & wash room shall have antiskid floor tiles &
wall tiles of seramic upto height of 8 feet.Provision of rain water discharge pipes at
different locations and two nos of over head water tank of 2000 ltrs capacity etc as
per requirement and approved drawing. All bath room & toilet shall have water &
termite proof doors and provision of sliding louvers with exhaust fan.
Internal concealed wiring (including supply of flexible copper FRP 1.1 KV PVC
wire,conduits & its accessories,modular type switches & switch board,Junction
boxes with required MCB & Earth leakage detector switcghear etc),fixing of
7.9 lighting fixtures & switchgear ,ceiling fans of 1400 sweep and regulators( including Lot 1
supply) ,exhaust fan (including supply), Erection of all Lighting FIXTURES &
LAMPS (LED), D.C emergency lighting (including supply), as per approved
drawing and direction of Engineer In charge.
Supply, fitting and fixing of stainless steel pf 304 grade in hand railing using 50mm
dia of 2mm thick circular pipe with balustrade of size 32mmx32mmx32mm
@0.90mtr C/C and stainless square pipe bracing of size 32mmx32mmx32mm in
7.10 Lot 1
three rows in staircase as per approved design and specification, buffing,polishing
etc with cost, conveyance, taxes of all materials, labour, T&P etc required for the
complete in all respect
7.11 Installation of smoke and heat detection system of the building. Lot 1
Roads: Design, construction of roads and walkways/ shoulders within sub-
station(Switch yard area,colony area,approach road,control room building
area, main gate to the switch yard gate etc) as per specification, layout and
8 approved drawings complete. This also includes excavation in all types of
Engineer In charge. Provision of drains on both the side of the roads for
easy discharge of rain water.
3.75 mtrs concrete road with shoulder at both the side & shall have drain
on both side of the road as per technical specification indicated in the civil
8.1 Mtrs 600
section( Periphery roads outside switch yard fencing and colony roads)
7 mtrs concrete road with shoulder at both the side as per technical
specification indicated in the civil section(from the switch yard main gate to
8.2 Mtrs 1100
power transformer,approach road & infront of GIS cum control room
building & Shall have drain on both side of the road.
Drainage system:Collection of rainfall data, Design, construction of storm
water drainage scheme (RCC type), road-culverts,Shall have drain on both
side of the road and drains crossing cable trenches etc. as per
specification and approved drawing. This also includes excavation in all
9
types of soil or rocks,back filling,and disposal of excess earth as per the
direction of Engineer In charge. All the switch yard bays , roads water
drainage shall be connected to the main surface drain. As per approved
drawing and specification.
9.1 Storm water drain Mtrs. 700
9.2 Road-culverts, drain crossings Lots 1
9.3 Cable trench crossing Lots 1
Foundations for transformers :Design, engineering, supply of labour,
material, equipments and construction of Auto-transformer/Transformer
foundation including piling if any, all associated works, rail tracks, jacking
pads,anchor block RCC and PCC, miscellaneous structural steel including
oil collection pits, MS grating(if required), gravel filling, and other items etc.
not mentioned herein, but specifically required for the completion of the
work as per technical specification and approved drawing. (Rate shall be
10 inclusive of cement, reinforcement steel, angles,flats and form work
etc.)(all cement concrete shall have RCC ratio 1:1.5:3). Transformer RCC
foundation and Rail Track should be extended upto the approaching road
(However,the height of RCC foundation beyond transformer main plinth
area should be same as height of concrete road as per item under 4.2).
This also includes excavation in all types of soil or rocks,back filling,and
disposal of excess earth as per the direction of Engineer In charge.
500 MVA, 400/220KV ICT

10.1 Nos 2
Total weight with oil and tank: 450 MT (appox)
40 MVA, 220/33kV Power Transformer (Overall dimension of
transformer(appox) Length:7200 mm X Width 6000 mm X Height 6200 mm)
10.2 Nos 1
Total weight with oil and tank: 97.5 MT (appox) As Per Technical
Specification
STATION TRANSFORMER:Design, engineering, procurement of
labour,material including all associated works for construction of foundation
and DP structure for station transformers 33/0.415 KV,1000 KVA
STN TRANSFORMER as per approved drawing and specification.33 KV
AB Switch,HG Fuse,
DP Structure & Angles (duly painted),Chanels, Plinth for erection of the
10.3 transformer, including fixing and laying of (insulators,surge arresters,XLPE Nos 2
armoured power cables3.5 core 300 sq mm, LT out door kiosk near
transformers and other accessories for complete installation of transformer
as per standard) and instruction of Engineer In charge. As per the
specification and approved drawing.
OIL SUMP PIT:Oil collection (from transformers)sump pit with provision of

pump(5 HP, with auto level control , including cabling, fixing of control gear
11
)as per CIGRE. As per spec and approved drawing.
500 MVA, 400/220 KV ICT

11.1 Nos 1
>Oil capacity of each ICT in ltrs appox. : 110000 ltrs.
40 MVA,220/33 KV Transformer
11.2 >Oil capacity of each ICT in ltrs appox. : 50000 ltrs.
PCC before site surfacing :Providing and supplying all labour, material,
equipments etc. required for proper leveling of earth after erection of
structures and equipments and proper compaction by using roller of
adequate capacity(minimum 3 Ton capacity) with water sprinkling of switch
yard area. After proper leveling of the switch yard area (after anti-weed
12 treatment), spreading of plain cement concrete with mixing ratio 1:3:6 CUM 2640
(M10) and maintaining proper sloping for easy discharge of storm water
having concrete thickness of 75 mm. including rolling , dressing,
compacting,the area. This also includes excavation in all types of soil or
rocks,back-filling,and disposal of excess earth as per the direction of
Engineer in charge and approved drawing. (Switch yard area)
Metal Spreading: Providing supplying and laying two layers of machine
crushed metals (gravel) fill, the first layer after compaction shall make
minimum 50 mm thickness coarse/ layer of 20 mm nominal size
consolidated/ compacted and (by using roller as specified in the
13 specification).A final layer of 50 mm thickness of machine crushed 20 mm CUM 2640
nominal size of metals(gravel) above the first layer of 50 mm thickness and
as per the technical specification and instruction of Engineer in charge
above the PCC(1:4:8). The total compacted thickness of the metals(20 mm
Nominal) 100mm above the PCC.
PROVISION OF PLANTATION & GARDENING:Provision of gardens in
front of the control room building & other areas where can be provided as
per the site Engineer's instruction, including supply of atleast 100 nos. fruit
bearing trees, 100 nos. of decorative plants,garden grass,flowering
14 plants,soil treatment and its plantation including materials,labour and T&P. LOT 1
As per the instruction of Engineer in Charge . Provision of water tap with
water sprinkler arrangement including water pipe laying with control at
different location. Supply of All materials. Both side of the RCC roads shall
be provided with decorative plants as per the instruction of the Site
Engineer.
STONE PITCHING & TOE WALL:Stone pitching including making of toe
walls both at top and bottom, including surface drain both at top and
bottom and partition wall in every 10 mtrs by using boulders and RR
15 masonry walls respectively. This also includes excavation in all types of soil
or rocks,back filling,and disposal of excess earth and supply of materials
and labour as per the direction of Engineer In charge and as per approved
drawing and specification.
15.1 Excavation in Soft & Loose Soil Cum 200
15.2 P.C.C (1:3:6): Lean Concrete Grade M-10 Cum 22
15.3 RR Masonry (1:5) Cum 225
P.C.C (1:2:4): Lean Concrete Grade M-15
15.4 Cum 2
SWITCH YARD FENCING: Providing and fixing of G.I Goat mesh (2.5 mm
dia)( in a GI angle 50X50X6 mm frame having 50X6 mm GI flat bracing
corner to corner) fencing( the posts and links shall be of HD Galvanized )
in switch yard and other areas of the substation with a total fence height
complete as per specification and approved drawings, and as required
under the safety regulation of local, state and central government bodies
16 and as per instruction of the Engineer-in-Charge.(The PCC work for Mtr 900
grouting the post shall be 1:2:4 and a continuous Fly ash Brick masonry
work with ratio 1:5 and cement pointing of the joints, for the fencing up to a
height from the finished ground level) .This also includes excavation in all
types of soil or rocks, back filling,and disposal of excess earth as per the
direction of Engineer In charge. The earthing of the fencing as per
specification.
Fire wall: Design, engineering, procurement of labour, material including all
associated works for construction of fire-walls as per technical specification
and approved drawings(column shall be RCC ratio1:1.5:3 and the walls are
of fire resistant Fly ash Bricks).This also includes excavation in all types of
17 Nos 1
Engineer In charge. As per approved drawing and specification. Painting of
the walls as per direction of the Engineer in charge.
MAIN GATE & SWITCH YARD GATES:Design, engineering, procurement

of labour, material including all associated works for construction and fixing
of of a main gate and one no. switch yard gates with men gates as per
18 direction of Engineer In charge. Provision of gate lights (Post top lantern
type) on each pillar of the gate. It includes supply & fixing of light fixtures
including LED Gate lamp, LV XLPE cables, switchgear etc required to
complete works as per specification and approved drawings.(* REMARKS :
FOR SUPPLY OF ALL THE CABLES AS INDICATED ARE COVERED IN
THE supply)}
18.1 MAIN GATE NOS 1
18.2 WICKET GATE NEAR MAIN GATE NOS 1
SWITCH YARD GATE(ON BOTH SIDES OF 7MTRS. CONCRETE ROAD
18.3 OF SWITCHYARD) NOS 2
WICKET GATE NEAR SWITCHYARD
18.4 NOS 1
FIRE FIGHTING & DG BUILDING:(one building).Design, engineering and
construction of switchyard buildings including the piling where required, the
cost of material, supply of labour, cement, reinforcement- steel, form work
and excavation as per the approved drawing and technical specification (
The RCC structure frame should be in the ratio 1:1.5:3).This also includes
excavation in all types of soil or rocks,backfilling,and disposal of excess
19 earth as per the direction of Enginer In charge.As per approved drawings
and specification.
Area of the Fire Fighting & DG Room with portico at front side, stair case
to the top of the building ,.The details of of building construction shall be
as per the Tech spec.
A) Area of the D.G Room Building: 10mtrsX7 mtrs (70sq mtrs), B) Area of
the fire fighting Room Building: 10mtrX10 Mtrs(100 sq mtr).
RCC work including MS rods(FE500 and above grade) (including
19.1 excavation, PCC, Shuttering, etc. for column ,Beams and roofs etc) as per Lot 1
technical spec & approved drawings.
Brick masonry work in cement sand mortar 1: 6 with bricks of class
19.2 Lot 1
designation 75kg/mm2 as per technical spec & approved drawings.
Concrete Flooring to be provided on the floor l of the DG cum Fire Fighting
19.3 Lot 1
room as per technical spec & approved drawings.
External and internal wall painting with primer coat as per technical spec
mentioned in the civil section. External: One coat weather coat primer +
19.4 two coats of weather coat colour paint. Lot 1
Internal: Two coats wall putty+solvent thinable white primer of one
coat+two coats colour paint. Refer the specification.
Doors and windows shall be of sliding type with locking facility and shall be
19.5 of aluminium with glaze of 6mm & windows shall have aluminium grills. As Lot 1
per technical spec & approved drawing.
Provision of PHD and other fittings of reputed make having ISI mark
,provision of rain water discharge pipes at different locations and etc as per
19.6 requirement and approved drawing & technical specification & as per Lot 1
instruction of Engg- in-Charge. It includes supply of all types of materials of
reputed make, labour etc to complete the work.
Internal concealed wiring,fixing of lighting fixtures(LED) ,fans and
regulators(Electronic regulator) ,exhaust fan,D.C emergency lighting
19.7 Lot 1
INCLUDING SUPPLY OF ALL ITEMS as per spec & approved drawing.
19.8 Provision of Water Tank for fire fighting below ground. Lot 1
SECURITY SHED & CUM VISITOR ROOM: Design, engineering,
procurement of labour, material including all associated works for
construction of Security shed near main gate,watch tower shed at the
corners of switch yard as per the approved drawing and instruction of
Engineer in charge. This also includes excavation in all types of soil or
rocks,back filling,and disposal of excess earth as per the direction of
23 Engineer In charge. Internal electrification including supply of lighting
fixtures,fan with regulators and provision of incoming AC supply from the
main ACDB/outdoor kiosks installed for street light or colony quarters. Also
includes painting of the building (in side and out side) as per
recommended for colony building in the specification. (* REMARKS : FOR
SUPPLY OF ALL THE CABLES AS INDICATED ARE COVERED IN THE
supply)}
SECURITY SHED:The size of the security shed shall be 3.5 mtrsX5mtrs
and height of 3.5mtrs RCC roof,Fly ash Brick masonary works,plastering
and painting and fixing of MS doors and windows. Internal concealed
wiring (including supply of flexible copper FRP 1.1 KV PVC wire,conduits &
its accessories,modular type switches & switch board,Junction boxes with
required MCB & Earth leakage detector switcghear etc),fixing of lighting
fixtures & switchgear ,ceiling fans of 1400 sweep and regulators( including
23.1 supply) and provision of incoming AC supply from the main ACDB/outdoor Nos 1
kiosks installed for street light or colony quarters. Also includes painting of
the building (in side and out side) as per recommended for colony building
in the specification. (* REMARKS : FOR SUPPLY OF ALL THE CABLES
AS INDICATED ARE COVERED IN THE supply)}
BORE WELL & PUMP HOUSE:Design, engineering, procurement of
labour, material including all associated works for construction of two nos.
bore wells for control room building including switch yard and colony
quarters as per specification and approved drawing and instruction of
Engineer in charge. This includes supply and fixing and commissioning of
two nos 5 HP submersible water pump with starter and other protection.
Construction of two nos pump house at ideal location for fixing of the
electrical starter units. The pump house be of RCC roof and having walls of
Fly ash Brick masonry and plastering and painting of external & internal
walls with MS door having locking arrangement & window. Internal
24 concealed wiring (including supply of flexible copper FRP 1.1 KV PVC LOT 1
wire,conduits & its accessories,modular type switches & switch board. The
size of the room shall be 2.5mtrsX2.5 mtrs having height of 3 mtrs. as per
approved drawing and specification. There shall be approach road to the
pump house. This includes supply of materials,labours and T&P &
excavation of all type of soils including rock and disposal of excess
materials as per instruction of Engineer In charge Supply & laying of LV
XLPE 3.5CX 35 sq mm cable from ACDB to pump house, control gear &
earthing of the system etc to complete the scheme as per approved
drawing & instruction of Engineer-in charge.
COLOUR CODING, BAY MARKING Etc:Design, engineering, procurement
of labour, material including all associated works for the followings. This
should be as per direction of site In charge. a)Color coding (red,Yellow &
Blue) for equipments,Bus gantry &column of entire switch yard. Good
25 quality weather proof sticker may be used for identification. b)Each bay Lot 1
should be identified with the help of bay marker sign board, suitably
grouted. MS sign board with stand to be installed. Proper painting and
lettering to be done of the entire switch yard area.
STORE SHED:Design, engineering, procurement of labour, material
including all associated works for construction of store shed as per
specification,approved drawing and direction of Engineer In charge. One
no store shed of floor size 10X10 mtr having Fly ash Brick walls and
plastering with RCC roof. The flooring shall be of 75 mm thickness PCC
(mix ratio1:2:4) over RR masonry works (as per standard practice of
flooring). Provision of adequate nos of MS racks (proper paintings also to
be done as per the direction of site in charge) for keeping the spare
26 materials. The height of the shed shall be 4mtrs above the plinth. Internal Lot 1
concealed wiring (including supply of flexible copper FRP 1.1 KV PVC
wire,conduits & its accessories,modular type switches & switch
board,Junction boxes with required MCB & Earth leakage detector
switcghear etc),fixing of lighting fixtures & switchgear ,ceiling fans of 1400
sweep and regulators( including supply) and provision of incoming AC
supply from the main ACDB/outdoor kiosks installed for street light or
colony quarters. Also includes painting of the building (in side and out side)
as per recommended for colony building in the specification. (* REMARKS :
FOR SUPPLY OF ALL THE CABLES AS INDICATED ARE COVERED IN
THE supply)}
PLATFORM FOR STORING EQUIMENTS:Design, engineering,
procurement of labour, material including all associated works for
construction of a platform for storing of bushings,Instrument transformers
etc, as per specification and approved drawing.This also includes
excavation in all types of soil or rocks,backfilling,and disposal of excess
earth as per the specification,approved drawing and direction of Engineer NOS 1
27
In charge. One no platform outside the store shed RR masonry
(compacted) with PCC at the top for storing the transformer bushings,
Instrument transformers, transformer oil drums etc. The floor size of the
platform shall be 15mtrX10 mtr with Galvanised Corrugated Sheet (Tata
Make) top cover and associated MS supporting structure duly painted.
28 Anti-Weed Treatment
28.1 Supply of labour,T&P,Chemicals and other necessary arrangements for
anti-weed treat of the switch-yard areas,controlroom etc. as per the
instruction of Engineer-in-Charge.The chemical to be sprayed as per the Sq Mtrs 24000
standard practice adopted for antiweed treatment of sub-station area & as
per the technical specification.
VEHICLE PARKING SHED: The size of the parking area shall be 15mtrs X
15 mtrs, out of the entire area there shall be provision of shed for 5 mtrs X
15 mtrs and rest of the area shall be without shed. 100 mm thick
29 Lot 1
PCC(1:2:4) flooring after the preparing the foundation base & Roof of the
parking place shall be RCC & Parking shed shall be as per TS-E6-Civil &
as per the direction of Engineer in Charge.
Construction of township/colony (residential quarters) for staff and
employees of the employer. Layout, design, survey, levelling, site dressing
and clearing of the area, soil investigation, excavation, PCC, RCC, Fly ash
Brick work, plastering ,flooring(flooring shall be with vitrified tiles of reputed
make with a dado of minimum6 inches),fixing of doors windows and
window grills, including all labour, T&P, material like cement ,sand
aggregate, Fly ash Bricks, reinforcements etc with all bought items required
for completion of the quarters as per approved construction drawings with
all facilities for supply of drinking water. The outer paint shall be applied
with weather coat synthetic enamel paint as per the standard practice of
application and the inner paint shall be applied with distemper of approved
quality as per the instruction and approval of the same by OPTCL. This
also includes excavation in all types of soil or rocks,back filling,and
30 disposal of excess earth as per the direction of Engineer In charge. Internal
electrical wiring with fixing of light fixtures and fans with electronic
regulators and exhaust fans as per technical specification and approved
drawing. Construction of over head RCC tank(1000 ltrs capacity one for
each quarters), sewerage disposal and connection with main sewerage/
septic tank and soak pit, storm water and surface drainage, culverts, roads,
with suitable radius on the curves and its connection with main road the
substation, street lighting, internal lighting, internal plumbing and sanitation
including internal/external finishing of quarters etc. required for completion
of the town ship. (RCC column structure frame and the Fly ash Bricks to be
used shall be fly ash Fly ash Brick, all the door and window frame & panels
shall be aluminium with adequate size as indicated in the TS and also as
per the National Building Code adopted.
30.1 "D" type Quarter As per technical specification: 1 no quarter on
ground floor & 1 no quarter on First floor ,the size of each quarter
plinth area shall be 120 Sq Mtrs(appox)
30.1.1 "D" type Quarter As per technical specification: 1 no quarter on
ground floor & the size of quarter plinth area shall be 120 Sq SQ.MTRS 120
Mtrs(appox)
30.1.2 "D" type Quarter As per technical specification: 1 no quarter on First
floor & the size of quarter plinth area shall be 120 Sq Mtrs(appox) SQ.MTRS 120
"E" type Quarter As per technical specification (one no. two storied
flat. Each flat shall be with 2 nos quarters on ground floor & 2 Nos
30.2
quarters on 1st floor).(There shall be 4 Nos quarters to be
accommodated in one flat as E1,E2,E3 & E4)
"E" type Quarter As per technical specification: 2 nos quarters on
30.2.1 ground floor (Each quarter size plinth area shall be 73 Sq Mtrs(appox) SQ.MTRS 146
"E" type Quarter As per technical specification: 2 nos quarters on

30.2.2 first floor(Each quarter size plinth area shall be 73 Sq Mtrs(appox) SQ.MTRS 146
A TOTAL CIVIL WORK (PART-A)

PART B ELECTRICAL WORK
3150A, 63kA for 3s, one and half Circuit Breaker (Circuit breaker shall be E2-C2-M2
class as per IEC 62271-100) arrangement. 420kV OUTDOOR GIS EQUIPMENT as per
1 latest IEC standard & type tested equipment as per technical specification, with
open future proof & flexible system in line with IEC 61850 & IEC 62271-203.
420kV,3150A, 63KA for 3 sec (Busbar, CB, Disconnector, Grounding switch, CT & PT),
SF6 gas insulated Complete Diameter module (2 Nos Feeder) each comprising of SF6 gas
insulated Single Pole Circuit Breaker (3 Sets) with CSD (Control Switching Device), Single
Phase Current Transformer (18 Nos), Single Phase Potential Transformer (4 Winding) (6
Nos), Motorised 3 Phase Disconnector (6 Sets), Motorised safety Grounding switch (8
Nos), Motorised 3 Phase Disconnector with high speed fault making Motorised Grounding
switch (2 Nos), Local Control Cubicle, SF6 gas monitoring system for complete diameter,
SF6 bus duct termination arrangement, online PD sensor (adequate number of UHF
1.1 Set 3
sensors in the offered GIS equipment for detection of Partial discharge (of 5 pC and
above) as per IEC 60270 through Partial Discharge (PD) monitoring system), different gas
compartment, O-ring & gaskets, Nuts, Bolts & Washers for Outdoor use, Absorbent,Limit
Switch, SF6 Gas, etc. to complete diameter module & its earthing arrangement with
earthing strips of adequate size (as per IEEE Std 80-2013 to protect operating staff against
any hazardous touch voltages and electro-magnetic interferences) as per the technical
specification.
420kV,3150A, 63KA for 3 sec (Busbar, Disconnector, Grounding Switch & Bus PT), 3
Phase Isolated, SF6 gas insulated, metal enclosed busbars Complete Diameter module (2
Nos BUS-PT) in bus enclosures running along the length of the switchgear to interconnect
each of circuit breaker diameter module. Each busbar set shall be complete with Potential
Transformer (4 Winding), Motorised 3 Phase Disconnector (1 No), Motorised Busbar
safety Grounding switch (1 No), Local Control Cubicle, SF6 gas monitoring system online
PD sensor (adequate number of UHF sensors in the offered GIS equipment for detection
1.2 Set 1
of Partial discharge (of 5 pC and above) as per IEC 60270 through Partial Discharge (PD)
monitoring system), different gas compartment, O-ring & gaskets, Nuts, Bolts & Washers
for Outdoor use, Absorbent, Limit Switch, SF6 Gas, etc. to complete diameter module & its
earthing arrangement with earthing strips of adequate size (as per IEEE Std 80-2013 to
protect operating staff against any hazardous touch voltages and electro-magnetic
420kV, 3150A, 63kA, 3 Sec, Single phase, SF6 gas Insulated Bus Duct outside GIS Bay
along with associated Support structure arrangement bends, joints, accessories, & its
1.3 earthing arrangement with earthing strips of adequate size (as per IEEE Std 80-2013 to RM 900
interferences) etc. as per the technical specification.
420kV, 3150A, 63kA, SF6/Air BUSHING (Bushing shall be of Polymer / composite insulator
type and shall be seamless sheath of a silicone rubber compound. The hollow silicone
1.4 composite insulators shall comply as per IEC 61462 and IEC 62217. The design of the No 18
composite insulators shall be tested and verified according to IEC 61462) FOR
CONNECTING GIS TO AIS along with support structure.
420kV GIS equipment system shall have Online continuous Partial Discharge Monitoring
System (PDM) system to provide an automatic facility for the simultaneous collection of
PD data at multiple points on the GIS & its associated GIB ducts and Voltage Transformers
adopting UHF technique & the data stored shall provide a historical record of the progress
of PD sources and shall identify the areas of maximum activity. PDM system shall be
1.5 Set 1
interfacing with UHF PD couplers provided. The PD Monitoring PC Work Station along with
all accessories shall be considered. Power supply to PDM PC shall have protection against
surges, overload and short circuit. A dedicated on-line UPS system shall also be provided
as a backup during supply interruption, to ensure trouble-free & reliable running of the
PDM System for a minimum of 15 minutes duration.
3150A, 50kA for 3s, Double Busbar Circuit Breaker (Circuit breaker shall be E2-C2-
M2 class as per IEC 62271-100) arrangement.
2 245kV OUTDOOR GIS EQUIPMENT as per latest IEC standard & type tested
equipment as per technical specification, with open future proof & flexible system in
line with IEC 61850 & IEC 62271-203.
245kV, 3150A, 50kA for 3 sec (Busbar, CB, Disconnector, Grounding Switch & CT), SF6
gas insulated ICT Feeder Bay Module each comprising of SF6 gas insulated Single Pole
Circuit Breaker (1 Set), Single Phase Current Transformer (6 Nos), Motorised Busbar 3
Phase Disconnector (2 Nos), Motorised Disconnector (1 No), Motorised safety Grounding
switch (3 Nos), Local Control Cubicle, SF6 gas monitoring system for complete bay, SF6
bus duct termination arrangement (3 Nos), PD sensor (adequate number of UHF sensors
in the offered GIS equipment for detection of Partial discharge (of 5 pC and above) as per
2.1 Set 3
IEC 60270 through Partial Discharge (PD) monitoring system), different gas compartment,
O-ring & gaskets, Nuts, Bolts & Washers for Outdoor use, Absorbent, Limit Switch, SF6
Gas, etc. to complete ICT Feeder Bay Module & its earthing arrangement with earthing
strips of adequate size (as per IEEE Std 80-2013 to protect operating staff against any
hazardous touch voltages and electro-magnetic interferences) as per the technical
specification.
245kV, 3150A, 50kA for 3 sec (Busbar, CB, Disconnector, Grounding switch, CT & PT),
SF6 gas insulated Line Feeder Bay Module each comprising of SF6 gas insulated Single
Pole Circuit Breaker (1 Set), Single Phase Current Transformer (6 Nos), Single phase Line
Potential Transformer (4 winding) (3 Nos), Motorised 3 Phase Busbar Disconnector (2
Nos), Motorised safety Grounding switch (2 Nos), Motorised 3 Phase Disconnector with
high speed fault making Motorised Grounding switch (1 No), Local Control Cubicle, SF6
gas monitoring system for complete bay, SF6 bus duct termination arrangement (3 Nos),
2.2 PD sensor (adequate number of UHF sensors in the offered GIS equipment for detection Set 4
of Partial discharge (of 5 pC and above) as per IEC 60270 through Partial Discharge (PD)
monitoring system), different gas compartment, O-ring & gaskets, Nuts, Bolts & Washers
for Outdoor use, Absorbent, Limit Switch, SF6 Gas, etc. to complete Line Feeder Bay
Module & its earthing arrangement with earthing strips of adequate size (as per IEEE Std
80-2013 to protect operating staff against any hazardous touch voltages and electro-
245kV, 3150A, 50kA for 3 sec (Busbars, Disconnector, Grounding switch & bus PT), 1
Phase Isolated Bus-PT Bay Module comprisig of SF6 gas insulated metal enclosed
busbars each enclosed in bus enclosures running along the length of the switchgear to
interconnect each of circuit breaker bay module. Each busbar set shall be complete with
Single phase bus Potential Transformer (4 winding) (3 Nos), Motorised 3 Phase
Disconnector (1 No) , Motorised Busbar safety Grounding switch (1 No), Local Control
Cubicle, SF6 gas monitoring system PD sensor (adequate number of UHF sensors in the
2.3 Set 1
offered GIS equipment for detection of Partial discharge (of 5 pC and above) as per IEC
60270 through Partial Discharge (PD) monitoring system), different gas compartment, O-
ring & gaskets, Nuts, Bolts & Washers for Outdoor use, Absorbent, Limit Switch, SF6 Gas,
etc. to complete the bus & its earthing arrangement with earthing strips of adequate size
(as per IEEE Std 80-2013 to protect operating staff against any hazardous touch voltages
and electro-magnetic interferences) as per the technical specification.
245kV, 3150A, 50kA for 3 sec (CB, Disconnector, Grounding switch & CT), SF6 gas
insulated Bus Coupler Bay Module comprising of SF6 gas insulated Single Pole Circuit
Breaker (1 Set), Single Phase Current Transformer (6 Nos), Motorised 3 Phase
Disconnector (2 Nos), Motorised safety Grounding switch (2 Nos), Local Control Cubicle,
SF6 gas monitoring system, PD sensor (adequate number of UHF sensors in the offered
GIS equipment for detection of Partial discharge (of 5 pC and above) as per IEC 60270
2.4 Set 1
through Partial Discharge (PD) monitoring system), different gas compartment, O-ring &
gaskets, Nuts, Bolts & Washers for Outdoor use, Absorbent, Limit Switch, SF6 Gas, etc. to
complete Bus Coupler Bay Module & its earthing arrangement with earthing strips of
adequate size (as per IEEE Std 80-2013 to protect operating staff against any hazardous
touch voltages and electro-magnetic interferences) as per the technical specification.
245kV, 3150A, 50 kA, 3 sec, single phase, SF6 gas Insulated Bus Duct outside GIS Bay
along with associated Support structure arrangement bends, joints,accessories, & its
2.5 earthing arrangement with earthing strips of adequate size (as per IEEE Std 80-2013 to RM 1000
245kV,3150A, 50kA SF6/Air BUSHING (Bushing shall be of Polymer / composite insulator
type and shall be seamless sheath of a silicone rubber compound. The hollow silicone
2.6 composite insulators shall comply as per IEC 61462 and IEC 62217. The design of the No 21
composite insulators shall be tested and verified according to IEC 61462) FOR
CONNECTING GIS TO AIS along with support structure.
245kV system shall have Portable Partial Discharge Monitoring System (PDM) & shall be
capable for measuring PD in charged GIS environment, bandwidth in order of
100MHz–2GHz & provision to select a wide range of intermediate bandwidths and the
2.7 principle of operation shall be based on UHF principle of detection. The Detection and Set 1
measurement of PD and bouncing particles having in built large coloured LCD for
displaying and storing facility in the instrument for further analysis to locate actual source of
PD such as free conducting particles, floating components, voids in spacers, particle on
spacer surfaces etc.
3.2 420KV 1 phase Solid core bus post insulator (AIS) as per technical specification. NOS 6
3.4 245KV 1 phase Solid core bus post insulator (AIS) as per technical specification. NOS 6
400KV metal oxide surge arrrestor, 20 KA , Long duration discharge class IV , 12KJ/KV at
3.5 NOS 18
336KV as per technical specification.
216KV metal oxide surge arrrestor, 10KA Long duration discharge class III , 10 KJ/KV at
3.6 NOS 21
216KV as per technical specification.
30 KV, METAL OXIDE SURGE ARRESTOR, 10kA, Long duration discharge class III (AIS)
3.7 NOS 9
as per technical specification.
36 KV ,1250A, 31.5 KA for 1 sec, isolator (single isolator with earth switch) including post
3.8 SET 2
insulators as per technical specification
36KV, 1250A, 31.5kA for 3 sec, SF6 gas insulated transformer bay module each comprising of
SF6 gas insulated Vacuum circuit breaker , current transformer , bus-bar disconnectors with common
4.1 grounding switch , SF6 gas monitoring system for complete bay (having 33 KV Bus Bar of 2000 SET 3
Amp) to complete transformer bay module suitable for cable connection to transformer.
36KV, 1250A , 31.5kA for 3 sec, (33 KV Bus Bar 2000 Amp) SF6 gas insulated bus-coupler bay
module comprising of SF6 gas insulated vacuum circuit breaker , current transformer , disconnector
switches & bus bars each enclosed in bus enclosures running along the length of the switch gear to
4.2 Nos 1
inter-connect each of circuit breaker bay module. Each busbar set shall be complete with potential
transformer , disconnectors, SF6 gas monitoring system for the complete bus etc.
Laying and termination of EHV/HV XLPE Power copper conductor cable for the
GIS system as per IS7098 & IEC60840 including installation of indoor & outdoor
4.3
cable termination kit and associated cable accessories & clamps as per technical
specification and direction of Engineer-in -charge.
36 KV XLPE 630 SQ. MM single core copper Cable as per tech spec (for
4.3.1 connectivity from 33 KV side of 220/33 KV Transformer to 33 KV GIS panel) Mtr 600
including installation of indoor & outdoor cable termination kit
33KV CABLE 300 SQ. MM single core copper as per tech spec (for 33 KV
connectivity from GIS equipment to Station Transformer (two nos station trafo) &
4.3.2 Mtr 1500
outgoing feeders upto DP structure end) including installation of indoor & outdoor
cable termination kit .
4.4 HV Test Charges for 33 KV GIS LOT 1
4.5 36 KV Bus Post Insulator as per technical specification NOS 9
5 BUS BAR & CIRCUIT MATERIALS

SUBSTATION EARTHING SYSTEMS: Substation earth mat Design,
engineering, supply(except the GI Flats, only erection) inclusive of
corrosion protection measures if any,laying of earth mat conductors of
Hot dip galvanised flats of size 75X12 mm to the approval of Engineer in
charge, excavation, welding/jointing of ground conductors along with risers
(a) upto Finished level from the mat size 75X12 mm & b) from the finished
ground level to the top of the structure and equipment shall be with 75x10
and 50X6 mm GI Flats, with back filling and good compaction,grounding
driven rods(40 mm MS solid rod for untreated earth pit ,perforated 50 mm
6 Heavy duty GI pipes for treated earth pits (with details of treatment as per
IS). The spacing between the earth conductor not more than 5 mtrs(both
way) and to be buried at depth of 700mm from the finished ground level.
For provision of treated earth pit and untreated earth pit, refer the
specification for designing. Provision of water taps inside the switch yard
areas and peripheral treated and un-treated earth pit are required to be
provided for watering the treated earth pits. The no. of treated and un
treated earth pits are to be done as per the practice and as indicated in the
drawing for different equipments. This is as per approved drawing and
specification.
6.1 Mtrs 17000
EARTHING CONDUCTOR: 75X 10 mm GI (HDG) Flat for Raiser from the
6.2 Mtrs 7000
burial earth mat to equipment,structure etc)
EARTHING CONDUCTOR: 50X6mm GI (HDG) Flat for Raiser for console
6.3 Mtrs 3000
box,LT panels,DC panels,Marshalling boxes etc)
EARTHING DEVICE & ASSOCIATED ACCESSORIES (50 mm heavy duty
6.4 Nos 180
GI PERFORATED PIPE 3 mtrs long for treated earth pit)
EARTHING DEVICE & ASSOCIATED ACCESSORIES 40mm MS rod 3
6.5 mtrs long for non treated earth pit) Nos 170
G.I Cable Trays including support GI angle suitable for different sections
along with its accessories as per TS. Details of No. of tiers are indicated in
7 the TS-Civil Section accordingly the requirement can be ascertained.

8 side & 220 kv side and other area ) as per Technical Specification. NOS 3
SWITCH YARD RECEPTACLE BOARD FOR TFR OIL FILTERATION (01

9 NOS 1
no. near 400/220KV ICT) as per Technical Specification.
10 NOS 2
11 BOLTS) FOR 400Kv & 220KV CLASS

11.1
11.2 FOR ALL 400KV, 220KV & 33 KV EQUIPMENT INCLUDING HIGH LEVEL
SA NEAR TRANSFORMER.
11.2.1 EQUIPMENT MT 75
40 Mtrs heigh Monopole Lighting cum Lightning Mast including LED lighting
11.2.2 MT 21
fixtures with control gear panel etc suitable for wind zone-V.
11.3 MT 11.6
Laying of Power and Control Cable including fixing of cable with terminal
connections both at equipments and control panels with supply of and
fixing of lugs, Ferrules, clamps, connectors, glands, fixing of cable trays,
including supply of N&B, Link plates, Cable Markers, Plaster of Paris, M-
12
Seal compounds etc for sealing purpose and all necessary arrangements,
laying of Earthing Flats, earthing ,laying of Cable trench slabs and
chequered plate etc for the cable trench,Cable scheduled and cable
diagram to be prepared by the contractor
12.1 ALUMINIUM CONDUCTOR (As per Specification)
12.1.1 XLPE-3.5 CX185 mm2 Mtrs 500

12.1.2 XLPE-3.5 CX120 mm2 Mtrs 500
12.1.3 PVC-3.5 CX70 mm2 Mtrs 250
12.1.4 PVC-3.5 CX35 mm2 Mtrs 500
12.1.5 PVC-4 CX 16 mm2 Mtrs 1000
12.1.6 PVC-4 CX 6 mm2 Mtrs 1000
12.1.7 PVC-2CX 6 mm2 Mtrs 2000
12.2
ARMOURED STRANDED(As per specification).
12.2.1 4 CX 2.5 mm2 Mtrs 6000
12.2.2 5 CX 2.5 mm2 Mtrs 4000
12.2.3 7CX 2.5 mm2 Mtrs 5000
12.2.4 10 CX 2.5 mm2 Mtrs 10000
12.2.5 12 CX 2.5 mm2 Mtrs 5000
12.2.6 16 CX 2.5 mm2 Mtrs 5000
12.2.7 19 CX 2.5 mm2 Mtrs 3000
7kg/sqmm or better & ITS ACCESSORIES LIKE ALL TYPE OF SOCKETS
13 LOT 1
& BENDS FOR TAKING CABLE FROM TRENCH TO EQUIPMENT MB etc

48 Fibre Optic Approach cable along with HDPE Pipes(As per the erection KM
14.1 1
charges mentioned in the Price Bid of Chandaka-B)
14.2 Erection/comissioning of SDH/MUX along with termination with FODP No 2
14.3 Erection/commissioning of digital tele-protection coupler No 1
14.5 SMPS based Battery Charger of 75A suitable for 48V VRLA Battery set No 1
2.5 sq. mm muti strand 2 core control cable(power supply,Transducer/MFT
14.6 Metre 600
PT supply)
14.7 2.5 sq. mm multi strand 4 core control cable(Transducer/MFT CT supply) Metre 600
14.10 48V DCDB No 1
14.11 Earth Flat, Cable Tray, Telephone cable, Foundation rail, Junction Box,. Lot 1
STATION TRANSFORMER 33KV/0.43 V,500 KVA (Confirming to Energy
15.1 NOS 2
Efficiency Level 2 -AS PER SPECIFICATION & relevant IS)
One no. 4 pole structure (HDG Type) alongwith other equipment & materials
for two nos station transformers:
2. Channel & Angle FOR BRACING OF, CHANNEL for the SA & Isolator & HG
fuse etc.
3. 90 KN Disc/composite long rod Insulators for 33 KV (48 nos./12 sets) for bus,
Bus stringing using ACSR moose conductor & tension hardwares,other clamps &
connectors etc as per requirement.
4. 2sets of 33 KV Isolator (800 AMP) for 33 KV side of station trafo.
5. 2sets of 33 KV HG FUSE.
15.2 6. 125 Sq mm AAAC conductor suitable for connection between HG fuse & station SET 2
transformer bushing.
7. 2 sets of LT OUT DOOR KIOSK MADE OUT OF 3mm CRCA sheet Gl
MARSHALLING BOX suitable for outdoor mounting. The bus bar suitable for 1000
AMP shall be arranged in the out door kiosk and other Facility like two sets of 400
Amps MCCB for incoming & outgoing with required sizes of terminal studs for
power cable termination & any other accessories required.
AII materials shall be As per relevant latest IS & as per the direction of Engg. in
charge

16 DRAWINGS )(Switch yard and other street area)(Including provision of the
fittings on the LM)
SUB-STATION SWITCH YARD LIGHTING,IT INCLUDES SUPPLY OF FIXTURES &
LAMPS (LED) of reputed make (Philips/CGL/Bajaj/ any other approved make of OPTCL)
16.1 with switch gear,GI Conduit etc.(Lighting fixtures are to be fixed rigidly on the Column at a
SET 60
suitable height so that the required lux can be achieved).(150 watt each)
STREET LIGHTING: IT INCLUDES SUPPLY OF GI TUBULAR POLE AS PER
TECHNICAL SPECIFICATION, LED LIGHTING FIXTURES including LAMPS of reputed
17 make (Philips/CGL/Bajaj).(100 watt each) for Street Light. (TO BE PROVIDED IN THE
SWITCH YARD, ALONG THE ROADS (APPROACH INSIDE YARD AND OTHER
ROADS).
LED LIGHTING FIXTURES including LAMPS of reputed make (Philips/CGL/Bajaj/ any
17.1 other approved make of OPTCL).(100 watt each) for Street Light.
SET 60
GI Tubular Pole: (410-SP-24: IS 2713-Part-II-1980 or latest) Length of pole
8.5 mtrs(minimum weight 158 Kgs).
AT A HEIGHT OF 1 METRE FROM THE GROUND. THE JUNCTION BOX
SHALL HAVE PROVISION OF FUSES, BUSES, CONNECTORS FOR
CABLE IN AND OUT.
OUTDOOR KIOSK of 3 mm thick CRCA sheet duly hot dip galvanised FOR
17.3 STREET LIGHT HAVING 2 NOS 200 AMP SWITCH FUSE UNITS AND NO 2
10 NOS. OUT LETS OF 32 AMP MCB.
FOR COMPLETING THE A.C SCHEME.(AS PER SPECIFICATION ) FOR
18 NOS. 20
CONTROL ROOM, CARRIER ROOM & CONFERENCE ROOM.,OFFICE
ROOM etc which includes all type of cables & wires and a main control
switch gear kiosk having sufficient outlet for each air conditioner unit.

ANNEXURE - I)
19.4 CO2 - 4.5 KGS NOS 10
19.5 CO2 - 9 KGS NOS 10
19.6 CO2 (TROLLY MOUNTED)- 22.5 KGS NOS 4
SUBSTATION AUTOMATION SYSTEM FOR 400/220 KV SUBSTATION ON PRP MODE:
Design , engineering , drawing, supervision, installation , testing & commissioning of
Substation Automation system alongwith Supply of the following 400,220,and 33 kV level
20 of protection panels consisting of Bay control Units & numerical protection relays and
other auxiliary relays suitable for SAS as per technical specification.
Yard AC Kiosk :5000 mm (L)x4000mm (W)x 3300mm (H) with AC, as per the
20.1 Nos. 4
Specification;
Gate way panel for Sub-Station Automation (in PRP as per the specification & indicative
drg ) system (for All 400 , 220 & 33 KV side bays including the future bays),other
accessories (comprising servers, engg. Station, works station (Main & standby), Remote
station control, Colour Laser jet Printers & dot matrix printer for local station as per
requirement and also for remote station, Ethernet Switches , LIU, Red Box, Multimode
20.2 glass fibre Doublle jacket armoured optical cables, special cables like F.O patch cord & SET 1
armoured FO cables of adequate length etc required for the system in all respect as per
latest IEC 61850 standard, Inverters of required capacity & rating (3KVA-Input shall be
both A.C & D.C and output shall be A.C) etc as per TS. A Full HD LED screen of 70
inches for display including all type of accessories & as per technical specification.
BCU for Substation Auxilliary System (Datas for monitoring of Station AC, Station DC,
20.3 Lighting, Fire fighting, Air conditioning, Diesel generator etc. as per the site requirement) SET 1

400 KV SIDE PROTECTION & OTHER PANELS as per Technical specification.
20.5
FEEDER PROTECTION PANEL (MAIN-I , MAIN-II & BACK-UP PROTECTION WITH
20.5.1 AUTO RECLOSURE DISTANCE PROTECTION with Bay control unit (BCU) for substation NOS 4
automation system.
TRANSFORMER PROTECTION PANEL (DIFFERENTIAL I &II , REF I & II & BACK-UP
20.5.2 PROTECTION for HV & IV side CONSIDERING HV ,IV & LV side for 500 MVA SET 2
400/220/33 KV ICT) with Bay control units (BCU) for substation automation system.
TIE BREAKER PROTECTION PANEL with Bay control unit (BCU) for substation
20.5.3 NOS 3
automation system.
BUS-BAR PROTECTION PANEL ( Including Provision of bus bar modules for the future
20.5.4 NOS 1
bays and to be integrated with the Automation system)
FEEDER PROTECTION PANEL (MAIN-I , MAIN-II & BACK-UP PROTECTION WITH
20.6.1 AUTO RECLOSURE DISTANCE PROTECTION with Bay control unit (BCU) for substation NOS 4
automation system.
TRANSFORMER PROTECTION PANEL (DIFFERENTIAL I &II , REF I & II & BACK-UP
PROTECTION for HV & LV side CONSIDERING HV & LV side for 40 MVA220/33 KV
20.6.2 SET 1
Power Trnsformer) with Bay control units (BCU) for substation automation system.
BUS COUPLER PROTECTION PANEL with Bay control unit (BCU) for substation
20.6.3 automation system. NOS 1
BUS-BAR PROTECTION PANEL ( Provision of bus bar modules for the future bays and
20.6.4 NOS 1
to be integrated with the Automation system)
33 KV BUS COUPLER PROTECTION Panel with Bay control protection unit (BCPU) with
20.7.1 with all other relays & component required for complete prtection,control etc as per TS No 1
and also suitable for substation automation system.
PROTECTION CONSIDERING 2X500 KVA 33/0.43 KV ) with Bay control
20.7.2 protection units (BCPU) with with all other relays & component required for SET 1
complete prtection,control etc as per TS and also suitable for substation automation
system. [2nos. Feeeder bays in one panel]
21 AC & DC SYSTEM
21.1 AC SYSTEM
D.G INCOMING)
ACDB (HAVING 800A MCCB) AS PER SPECIFICATION (AC DB-1,AC DB-
21.1.2 2 WITH B/C) SET 1

21.1.3 SET 1
21.1.4 (WITH DB-1,DB-2 & B/C) SET 1

21.2 DC SYSTEM
considered.
21.2.4 SET 2
other protection facility at the DC Load terminal end in order to feed 220 V
to the load).
22 FOR BATTERY BANKS SET 1

23 NOS 2
24 NOS 2
25 NOS 2
26 LOT 1
EQUIPMENT).
OFFICE FURNITURE (REFER TS-VOL-IIA-SCOPE OF WORKAT SL NO.
18 ANNEXURE - IV ,INDICATED IN SCHEDULE OF REQUIREMENTS
27 OFFICE FURNITURE) & PLACING IN CONTROL ROOM,CONFERENCE LOT 1
ROOM,OFFICE ROOMS,LIBRARY,TESTING LAB,etc.

mechanical & electrical protection as per latest IS with Automatic Mains
29 Failure feature as per Technical spec. NOS 1
ERECTION OF THE TRANSFORMERS AND ITS ACCESSORIES ON

THE PLINTH AND PLACING IN POSITION, ERECTION OF
ACCESSORIES OF THE TRANSFORMERS, EART-HING AS PER
STANDARD(INCLUDING SUPPLY OF MATERIALS),VACUUM
TREATMENT OF THE TANK AND WINDING,OIL
FILTRATION(INCLUDING SUPPLY OF VACUUM CUM OIL FILTER
MACHINE),SUPPLY & LAYING OF ALL TYPES OF CONTROL & POWER
CABLES PERTAINING TO TRANSFORMERS ,TESTING AND
30.0 COMMISSIONING INCLUDING ALL TESTS OF THE OILS AS PER
STIPULATION IN THE STANDARD APPROVED TESTING
LABORATORY AND AS PER THE INSTRUCTION OF THE ENGINEER IN
CHARGE.THIS INCLUDE ALL RELATED WORKS FOR
ERECTION,TESTING AND COMMISSIONING OF THE POWER
TRANSFORMERS.(CONTRACTOR TO ARRANGE POWER SUPPLY
FOR FILTRATION AND VACUUM TREATMENT WORKS).IT ALSO
INCLUDES SUPPLY OF ALL MATERIALS FOR ERECTION INCLUDING
T&P's.
30.1 400/220KV, 500 MVA ICT Nos 2
30.2 40 MVA, 220/33kV Power Transformer Nos 1
TOTAL OF ELECTRICAL WORKS (PART-B)
TOTAL OF ERECTION OF SUBSTATION (Electrical Work) & (Civil
Work) -Schedule-4-ss (to Schedule No. 6 Grand Summary)
1 Specify currency in accordance with specifications in Bid Data Sheet under ITB 19.1 in Single-Stage Bid, or ITB 34.1 in Two-Stage Bid.
(Ramkrushnapur),Bhadrak.in Odisha State of India under PACKAGE-3 Under Japan International Cooperation Agency (JICA)’s ODA Loan.
Schedule No. 6. Grand Summary
NAME OF THE BIDDER
Total Price1
Item Description
Foreign Local
1 Total Schedule No. 1. Plant,
Supplied from Abroad (Substation)
2 Total Schedule No. 2. Plant, Supplied from Within the Employer’s
Country (substation)
3 Total Schedule No. 3. Design Services (Not Applicable)
4
Total Schedule No. 4. Installation and Other Services (substation)
5 Total Schedule No. 5. Provisional Sums (Not to be considered for
Evaluation)
Total( to Bid Form)
Name of Bidder:__________________________
Signature of Bidder:__________________________
1
Specify currency in accordance with specifications in Bid Data Sheet under ITB 19.1 in Single-Stage Bidding, or ITB 34.1 in Two-Stage Bidding. Create and use as many columns for Foreign
NAME OF THE WORK:-Design, Supply and Installation of 2X500 MVA ICT for Out Door Type,400/220 KV GIS Grid Sub-station at (Ramkrushnapur),Bhadrak.in
Odisha State of India under PACKAGE-3 Under Japan International Cooperation Agency (JICA)’s ODA Loan.
Schedule No. 7. Recommended Spare Parts
NAME OF THE BIDDER
Unit Price
DESCRIPTION OF ITEMS
Sl. No. SUPPLY OF SPARES FOR THE FOLLOWING EQUIPMENTS. Unit Quantity CIP Ex-Works Price Total Price in INR
(As per Technical Specification) (foreign parts) Local Parts
(1) (2) (3) (1) x (2) or (3)
TOTAL
Name of Bidder:________________________________
Note: Recommended Spares shall not be taken in to consideration for evaluation purpose.
(Ramkrushnapur),Bhadrak.in Odisha State of India under PACKAGE-3 Under Japan International Cooperation Agency (JICA)’s
ODA Loan.
Schedule No. 8. Details of Taxes & Duties
NAME OF THE BIDDER
Total Amount of Taxes /Duty/
Sl No Description of Applicable Tax/Levy Tax @ __%
Levies
Details of Taxes and levies on the direct / bought out
1 transactions between Bidder and ODISHA POWER
TRANSMISSION CORPORATION LTD included in the Bid
(i) TOTAL IGST
(ii) TOTAL CGST
(III) TOTAL OGST
(iv) TOTAL Any other tax
TOTAL OF TAXES AND DUTIES [Sum (i) to (iv)
Details of Taxes and levies on the direct / bought out
transactions between Bidder and ODISHA POWER
2 TRANSMISSION CORPORATION LTD included in the Bid
Price above but as may be payable by ODISHA POWER
TRANSMISSION CORPORATION LTD (Schedue- 4)
(i) TOTAL IGST
(ii) TOTAL CGST
(III) TOTAL OGST
(iv) TOTAL Any other tax
TOTAL OF TAXES AND DUTIES [Sum (i) to (iv)
4 F. Total Bid Price: (including Taxes & Duties and other Name of Bidder:________________________________

150219110213amended BoQ Pkg-3 Vol II of III

Uploaded by

Copyright:

Available Formats

150219110213amended BoQ Pkg-3 Vol II of III

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

150219110213amended BoQ Pkg-3 Vol II of III

Uploaded by

Copyright:

Available Formats

ODISHA POWER TRANSMISSION CORPORATION LIMITED

Out Door type GIS S/S (New):400 KV Bay-

400/220/33 GIS S/S at Ramkrushnapur

(1) (2) (3) (1) x (3)

420kV,3150A, 63KA for 3 sec (Busbar, Disconnector, Grounding Switch &

245kV, 3150A, 50kA for 3 sec (Busbar, CB, Disconnector, Grounding

245kV, 3150A, 50kA for 3 sec (Busbars, Disconnector, Grounding switch

36 KV XLPE 630 SQ. MM single core copper Cable as per tech

All types of HARDWARES & FITTINGS/SPACERS/CLAMPS &

4.7 400 KV LA Clamp as per TS Set 18

4.10 220 KV LA Clamp as per TS Set 18

G.I Cable Trays(size: 450x75x2500mm)

SWITCH YARD RECEPTACLE BOARD FOR TFR OIL FILTERATION

SUPPLY OF STATION TRANSFORMER & OTHER MATERIALS FOR

SUB STATION LIGHTING (AS PER SPECIFICATION AND APPROVED

2 TR CAPACITY SPLIT AIR CONDITIONING UNITS WITH REMOTE

FIRE FIGHTING SYSTEM(PORTABLE /TROLLEY/ WHEEL

CARTWHEEL MOUNTED ALUMINIUM LADDER OF ADEQUATE

Out Door type GIS S/S (New):400 KV Bay-

(1) (2) (1) x (3)

420kV,3150A, 63KA for 3 sec (Busbar, Disconnector, Grounding Switch &

245kV, 3150A, 50kA for 3 sec (Busbar, CB, Disconnector, Grounding

36 kV Indoor type termination Kits (GIS side) suitable for 1CX300

4.7 400 KV LA Clamp as per TS Set 18

4.10 220 KV LA Clamp as per TS Set 18

EARTHING CONDUCTOR: 50X6mm GI (HDG) Flat for Raiser for

SUB STATION LIGHTING (AS PER SPECIFICATION AND APPROVED

INDOOR LIGHTING OF SECURITY SHED CUM VISITORS

BEST QUALITY &APPROVED MAKE INSULATING MAT (Confirming to

33 EQUIPMENT and MATERIALS for GIS

Quantity for: Construction of 2x500

Ramkrushnapur Out Door type GIS

2,TFR-2& B/C-1),220 KV Bay-2

Soil investigation : Supply of labour,T&Pand other necessary arrangements

Cutting, Filling and Levelling of Sub-station area including supply of

2.2.1 (i) Beyond 30 mtr & up to 100mtr lead CUM 3000

EXCAVATION FOR PREPARATION OF FOUNDATION WORK FOR THE

3.1.1 Normal Soil(SOFT/LOOSE) Cum 7000

RCC work including MS rods(FE500 and above grade) (including

500 MVA, 400/220KV ICT

OIL SUMP PIT:Oil collection (from transformers)sump pit with provision of

500 MVA, 400/220 KV ICT

MAIN GATE & SWITCH YARD GATES:Design, engineering, procurement

"E" type Quarter As per technical specification: 2 nos quarters on

A TOTAL CIVIL WORK (PART-A)

All types of HARDWARES & FITTINGS/SPACERS/CLAMPS &

7.1 G.I Cable Trays(size: 450x75x2500mm) MTRS 4500

SWITCH YARD RECEPTACLE BOARD FOR TFR OIL FILTERATION (01

DIFFERENT TYPES OF LATICE TYPE COLUMNS & DIFFERENT TYPE

12.1.1 XLPE-3.5 CX185 mm2 Mtrs 500

14 ACCESSORIES FOR PLCC SYSTEM With OPGW cable

SUB STATION LIGHTING (AS PER SPECIFICATION AND APPROVED

FIRE FIGHTING SYSTEM(PORTABLE /TROLLEY/ WHEEL

20.4 GPS System with PTP, IRIG-B, SNTP SET 1

MAIN LIGHTING DISTRIBUTION BOARD (HAVING 250A MCCB AS

21.1.5 EMERGENCY LIGHTING DISTRIBUTION BOARD SET 1

PORTABLE ALUMINIUM LADDER EXTENDABLE TYPE OF ADEQUATE

BEST QUALITY &APPROVED MAKE INSULATING MAT (Confirming to