V260B1 L03 ChiMei PDF

Issued Date: 7, May 2007
Model No.: V260B1 - L03

Approval
TFT LCD Approval Specification

MODEL NO.: V260B1 - L03
RoHS Verified
Customer:
Approved by:
Note:
TV Head Division
Approved By
LY Chen
QRA Dept. Product Development Div.

Reviewed By
Tomy Chen WT Lin
LCD TV Marketing and Product Management Div.

Prepared By
Denise Shieh Hui-I Wen
-
1
Version 2.1
Free Datasheet http://www.datasheet-pdf.com/
Approval
- CONTENTS -
REVISION HISTORY ------------------------------------------------------- 3
1. GENERAL DESCRIPTION ------------------------------------------------------- 4

1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
1.5 MECHANICAL SPECIFICATIONS
2. ABSOLUTE MAXIMUM RATINGS ------------------------------------------------------- 5
2.1 ABSOLUTE RATINGS OF ENVIRONMENT
2.2 PACKAGE STORAGE
2.3 ELECTRICAL ABSOLUTE RATINGS
2.3.1 TFT LCD MODULE
2.3.2 BACKLIGHT UNIT
3. ELECTRICAL CHARACTERISTICS ------------------------------------------------------- 7
3.1 TFT LCD MODULE
3.2 BACKLIGHT INVERTER UNIT
3.2.1 CCFL(Cold Cathode Fluorescent Lamp) CHARACTERISTICS
3.2.2 INVERTER CHARACTERISTICS
3.2.3 INVERTER INTERTFACE CHARACTERISTICS
4. BLOCK DIAGRAM ------------------------------------------------------- 12
4.1 TFT LCD MODULE
5. INTERFACE PIN CONNECTION ------------------------------------------------------- 13
5.1 TFT LCD MODULE
5.2 BACKLIGHT UNIT
5.3 INVERTER UNIT
5.4 BLOCK DIAGRAM OF INTERFACE
5.5 LVDS INTERFACE
5.6 COLOR DATA INPUT ASSIGNMENT
6. INTERFACE TIMING ------------------------------------------------------- 19
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
6.2 POWER ON/OFF SEQUENCE
7. OPTICAL CHARACTERISTICS ------------------------------------------------------- 22
7.1 TEST CONDITIONS
7.2 OPTICAL SPECIFICATIONS
8. DEFINITION OF LABELS ------------------------------------------------------- 26
8.1 CMO MODULE LABEL
9. PACKAGING ------------------------------------------------------- 27
9.1 PACKING SPECIFICATIONS
9.2 PACKING METHOD
10. PRECAUTIONS ------------------------------------------------------- 29
10.1 ASSEMBLY AND HANDLING PRECAUTIONS
10.2 SAFETY PRECAUTIONS
10.3 STORAGE PRECAUTIONS
11. REGULATORY STANDARDS ------------------------------------------------------- 30

12. MECHANICAL CHARACTERISTICS ------------------------------------------------------- 31
13. APPENDIX ------------------------------------------------------- 33
2
Version 2.1
Approval
REVISION HISTORY
Page
Version Date Section Description
(New)
Ver 2.0 10, Jan. 2007 All All Approval Specification was first issued.
Ver 2.1 7, May 2007 7 3.1 Rush Current is changed from 2.0 A to 3.0 A.
21 6.2 Update 1sT4
3
Version 2.1
Approval
1. GENERAL DESCRIPTION
1.1 OVERVIEW
V260B1- L03 is a TFT Liquid Crystal Display module with 12-CCFL Backlight unit and 1ch-LVDS
interface. The display diagonal is 26”. This module supports 1366 x 768 WXGA format and can display
16.2M colors (6-Bit+FRC colors). The inverter module for backlight is built-in.
1.2 FEATURES
- Excellent brightness 500nits
- Contrast ratio 800:1
- Fast response time (8ms)
- Color saturation NTSC 72%
- WXGA (1366 x 768 pixels) resolution
- DE (Data Enable) only mode
- LVDS (Low Voltage Differential Signaling) interface
- Viewing angle: 160(H)/150(V) (CR>10) TN technology
- Color reproduction (Nature color)
- RoHS compliance
1.3 APPLICATION
- TFT LCD TVs
- High brightness, multi-media displays
1.4 GENERAL SPECIFICATI0NS

Item Specification Unit Note
Active Area 575.769 (H) x 323.712 (V) (26” Diagonal) mm
(1)
Bezel Opening Area 580.8 (H) x 328.8 (V) mm
Driver Element a-si TFT Active Matrix -
Pixel Number 1366 x R.G.B. x 768 pixel
Pixel Pitch (Sub Pixel) 0.1405 (H) x 0.4215 (V) mm
Pixel Arrangement RGB Vertical Stripe -
Display Colors 16.2M color
Display Operation Mode Transmissive Mode / Normally White -
Anti-Glare Coating (Haze 25%)
Surface Treatment -
Hard Coating (3H)
1.5 MECHANICAL SPECIFICATIONS

Item Min. Typ. Max. Unit Note
Horizontal(H) 625 626 627 mm
Vertical(V) 372 373 374 mm
Module Size
Depth(D) 35.6 36.6 37.6 mm To PCB Cover
Depth(D) 42.7 43.7 44.7 mm To Inverter Cover
Weight - 4550 - g
Note (1) Please refer to the attached drawings for more information of front and back outline dimensions.
4
Version 2.1
Approval
2. ABSOLUTE MAXIMUM RATINGS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT
Value
Item Symbol Unit Note
Min. Max.
Storage Temperature TST -20 +60 ºC (1)
Operating Ambient Temperature TOP 0 +50 ºC (1), (2)
Shock (Non-Operating) SNOP - 100 G (3), (5)
Vibration (Non-Operating) VNOP - 1.0 G (4), (5)
Note (1) Temperature and relative humidity range is shown in the figure below.
(a) 90 %RH Max. (Ta 40 ºC)
(b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC)
(c) No condensation
Note (2) The maximum operating temperature is based on the test condition that the surface temperature of
display area is less than or equal to 60 ºC with LCD module alone in a temperature controlled chamber.
Thermal management should be considered in final product design to prevent the surface temperature of
display area from being over 60 ºC. The range of operating temperature may degrade in case of improper
thermal management in final product design.
Note (3) 2 ms, half sine wave, 1 time for ± X, ± Y, ± Z
Note (4) 10 ~ 500 Hz, 10 min, 1 time each X, Y, Z
Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough
so that the module would not be twisted or bent by the fixture.
Relative Humidity (%RH)
100
90
80
60
Operating Range
40
20
10 Storage Range
-40 -20 0 20 40 60 80
Temperature (ºC)
5
Version 2.1
Approval
2.2 PACKAGE STORAGE

When sorting modules as spares for a long time, the following precaution is necessary.
(a) Do not leave the module in high temperature, and high humidity for a long time. It is highly recommended
to store the module with temperature from 0 to 35 at normal humidity without condensation.
(b) The module shall be stored in dark place. Do not store the TFT-LCD module in direct sunlight or fluorescent
light.
2.3 ELECTRICAL ABSOLUTE RATINGS

2.3.1 TFT LCD MODULE
Value
Item Symbol Unit Note
Min. Max.
Power Supply Voltage Vcc -0.3 13.0 V
(1)
Input Signal Voltage VIN -0.3 3.6 V
2.3.2 BACKLIGHT UNIT

Test
Item Symbol Min. Type Max. Unit Note
Condition
Lamp Voltage VW Ta = 25 - - 3000 VRMS
Power Supply Voltage VBL - 0 - 30 V (1)
Control Signal Level - - -0.3 - 7 V (1), (2)
Note (1) Permanent damage to the device may occur if maximum values are exceeded. Functional
operation should be restricted to the conditions described under normal operating conditions.
Note (2) The control signals includes Backlight On/Off Control, Internal PWM Control, External PWM
Control and Internal/External PWM Selection.
Note (3) No moisture condensation or freezing.
6
Version 2.1
Approval
3. ELECTRICAL CHARACTERISTICS
3.1 TFT LCD MODULE Ta = 25 ± 2 ºC
Value
Parameter Symbol Unit Note
Min. Typ. Max.
Power Supply Voltage VCC 11.4 12.0 12.6 V (1)
Power Supply Ripple Voltage VRP - - 300 mV
Rush Current IRUSH - - 3.0 A (2)
White - 0.2 - A
Power Supply Current Black ICC - 0.5 0.7 A (3)
Vertical Stripe - 0.4 - A
Differential Input High
VLVTH - - +100 mV
Threshold Voltage
LVDS
Differential Input Low
Interface VLVTL -100 - - mV
Threshold Voltage
Common Input Voltage VLVC 1.125 1.25 1.375 V
Terminating Resistor RT - 100 - ohm
CMOS Input High Threshold Voltage VIH 2.7 - 3.3 V
interface Input Low Threshold Voltage VIL 0 - 0.7 V
Note (1) The module should be always operated within above ranges.
Note (2) Measurement Conditions :
+12.0V
Q1 AO4409
Vcc
C3
FUSE (LCD Module Input)
R1 1uF
200K
VR1
47K
(Low to High)
(Control Signal)
R2
Q2 C1
SW
2N7002
1K
10uF
Vcc rising time is 470us
+12V
0.9Vcc
0.1Vcc
GND
470us
7
Version 2.1
Approval
Note (3)The specified power supply current is under the conditions at Vcc = 12V, Ta = 25 ± 2 ºC, f v = 60 Hz,
whereas a power dissipation check pattern below is displayed.
a. White Pattern b. Black Pattern
Active Area Active Area
c. Vertical Stripe Pattern
R G B R G B
B R G B R G B R
B R G B R G B R
R G B R G B
Active Area
3.2 BACKLIGHT INVERTER UNIT

3.2.1 CCFL (Cold Cathode Fluorescent Lamp) CHARACTERISTICS (Ta = 25 ± 2 ºC)
Value
Min. Typ. Max.
Lamp Voltage VW - 970 - VRMS IL = 5.0mA
Lamp Current IL 4.5 5.0 5.5 mARMS (1)
- - 1650 VRMS (2), Ta = 0 ºC
Lamp Starting Voltage VS
- - 1500 VRMS (2), Ta = 25 ºC
Operating Frequency FO 40 - 80 KHz (3)
LBL 50,000 60,000 - Hrs (4)
ADIM High (3.3V)
Lamp Life Time 20,000
LBLb 120 %, Lamp Current
=6.0mA
8
Version 2.1
Approval
3.2.2 INVERTER CHARACTERISTICS (Ta = 25 ± 2 ºC)

Value
Min. Typ. Max.
Power Consumption PBL - 72 82 W (5)(6), IL = 5.0mA
Power Supply Voltage VBL 21.6 24 26.4 VDC
Power Supply Current IBL - 3 3.42 A Non Dimming
Input Inrush Current - - - 4.7 Apeak (7)
Input Ripple - - - 400 mVP-P VBL =21.6V
Input Noise - - - 800 mVP-P VBL =21.6V
Oscillating Frequency FW 55 58 61 kHz

Dimming Frequency FB 100 - 300 Hz
Minimum Duty Ratio DMIN 20 - 100 %
Note (1) Lamp current is measured by utilizing high frequency current meters as shown below:
A HV (Pink) 1
HV (White)
A 2
A HV (Pink) 1
HV (White)
A 2
A HV (Pink) 1
HV (White)
A 2
A HV (Pink) 1
LCD HV (White)
A 2 Inverter
A Module HV (Pink)
1
HV (White)
A 2
A HV (Pink) 1
HV (White)
A 2
LV (Black+)
LV (White,-)
Note (2) The lamp starting voltage VS should be applied to the lamp for more than 1 second under starting
up duration. Otherwise the lamp could not be lighted on completed.
Note (3) The lamp frequency may produce interference with horizontal synchronous frequency from the
display, and this may cause line flow on the display. In order to avoid interference, the lamp
frequency should be detached from the horizontal synchronous frequency and its harmonics as far
as possible.
9
Version 2.1
Approval
Note (4) The life time of a lamp is defined as when the brightness is larger than 50% of its original value
and the effective discharge length is longer than 80% of its original length (Effective discharge
length is defined as an area that has equal to or more than 70% brightness compared to the
brightness at the center point.) as the time in which it continues to operate under the condition Ta
= 25 2 and IL = 4.5~ 5.5mARMS.
Note (5) The power supply capacity should be higher than the total inverter power consumption PBL. Since
the pulse width modulation (PWM) mode was applied for backlight dimming, the driving current
changed as PWM duty on and off. The transient response of power supply should be considered
for the changing loading when inverter dimming.
Note (6) The measurement of Max. value is based on 26” backlight unit under 24V input voltage and 5.3mA
lamp in average after lighting for 30 minutes.
Note (7) The measurement condition of input inrush current is based on 26” backlight unit. The rising time
of power supply voltage must greater or equal to 20ms.
3.2.3 INVERTER INTERTFACE CHARACTERISTICS

Test Value
Condition Min. Typ. Max.
On/Off Control ON - 2.0 - 5.0 V
VBLON
Voltage OFF - 0 - 0.8 V
HI - - - 3.3 V
ADIM VADIM
LO - - 0 - V
High 2.0 - 5.0 V Logic High (open)
PDIM VPDIM -
Low 0 - 0.8 V Logic Low
10
Version 2.1
Approval
INVERTER INTERFACE IMPEDANCE

Pin No. Symbol Impedance
11 ADIM 172K10%
12 ON/OFF 67K10%
13 PDIM 51K10%
11
Version 2.1
Approval
4. BLOCK DIAGRAM
4.1 TFT LCD MODULE
SCAN DRIVER IC
RX0(+/-)
TFT LCD PANEL
(1366x3x768)
INPUT CONNECTOR
(JAE,FI-X30SSL-HF)
RX1(+/-)
RX2(+/-)
TIMING
RX3(+/-)
CONTROLLER
)
RXCLK(+/-)
Vcc
DATA DRIVER IC
GND
DC/DC CONVERTER &
REFERENCE VOLTAGE
CN3-CN8:
CP0403S0000 (CviLux) BACKLIGHT
or Equivalent
CN1 INVERTER CONNECTOR UNIT
Vin CN1: S14B -PH-SM4-TB(D)(LF)(JST)
GND or Equivalent
ADIM
ON/OFF
PDIM
GND
CN2: S2B-ZR-SM4A-TF (D)(LF)(JST) or Equivalent
12
Version 2.1
Approval
5. INTERFACE PIN CONNECTION

5.1 TFT LCD MODULE
CNF1 Connector Pin Assignment
Pin No. Symbol Description Note
1 VCC Power supply: +12V
5 GND Ground
6 GND Ground
7 GND Ground
8 GND Ground
9 SELLVDS Select LVDS data format (1),(4)
10 NC No connection (3)
11 GND Ground
12 RX0- Negative transmission data of pixel 0
13 RX0+ Positive transmission data of pixel 0
14 GND Ground
17 GND Ground
20 GND Ground
21 RXCLK- Negative of clock
22 RXCLK+ Positive of clock
23 GND Ground
26 GND Ground
29 GND Ground
30 GND Ground
Note (1) Please refer to 5.5 LVDS INTERFACE (Page 17)
Note (2) Connector Part No.: JAE,FI-X30SSL-HF or Compatible
Note (3) Reserve for internal use. Must be opened, if GND/High will cause abnormal display.
(But it will not cause panel damage)
Pin10 :Reserve pin (no function)
Pin27 :Aging mode function (H :enable ,L :disable)
Pin28 :Flicker adjustment (H :enable ,L :disable)
Note (4) The impedance of option pin is 50K ohm.
13
Version 2.1
Approval
5.2 BACKLIGHT UNIT

The pin configuration for the housing and leader wire is shown in the table below.
CN3-CN8 (Housing): CP0403S0000 (CviLux)
Pin No. Symbol Description Wire Color
1 HV High Voltage Pink
2 HV High Voltage White
Note (1) The backlight interface housing for high voltage side is a model CP0403S0000, manufactured by
CviLux. The mating header on inverter part number is CP042BP1MRO-LF (CviLux) or equivalent.
CN2 (Housing): ZHR-2 (JST) or Equivalent

Pin No. Symbol Description Wire Color
1 LV Low Voltage (+) Black
2 LV Low Voltage (-) White
Note (2) The backlight interface housing and return cable for low voltage side is a model ZHR-2 , manufactured
by JST or equivalent. The mating header on inverter part number is S2B-ZR-SM4A-TF(D)(LF) or
equivalent.
8 Female Connectors
CP0403S0000 (CviLux)
or Equal
1.HV(Pink,+)
2.HV(White,+)
1.HV(Pink,-)
2.HV(White,-)
1.HV(Pink,+)
2.HV(White,+)
1.HV(Pink,-)
2.HV(White,-)
1.HV(Pink,+)
2.HV(White,+)
1.HV(Pink,-)
2.HV(White,-)
ZHR-2 or Equal
Return Cable
1.LV(Black)
2.LV(White)
14
Version 2.1
Approval
5.3 INVERTER UNIT

CN1(Header): S14B-PH-SM4-TB(D)(LF)(JST) or Equivalent
Pin No. Symbol Description
1
2
3 VBL +24V Power Input
4
5
6
7
8 GND Ground
9
10
GND (0V) 80%
11 ADIM Open (1.6V) 100%
High (3.3V) 120%, Lamp current
12 ON/OFF BL ON/OFF (ON is High/Open, OFF is Low, )
13 PDIM PWM input signal, Open/High (3.3V, 100% Duty) for 100%
14 GND GND
CN2(Header): S2B-ZR-SM4A-TF or Equivalent

Pin No. Symbol Description
1 CCFL COLD CCFL low voltage (+)
2 CCFL COLD CCFL low voltage (-)
CN3-CN8 (Header): CP042BP1MRO-LF (CviLux) or Equivalent

Pin Name Description
1 CCFL HOT CCFL high voltage
2 CCFL HOT CCFL high voltage
Note (1) Floating of any control signal is not allowed.
15
Version 2.1
Approval
5.4 BLOCK DIAGRAM OF INTERFACE

CNF1
Rx0+ 51Ω
100pF RxOUT
TxIN Rx0- R0-R7
R0-R7 51Ω
Rx1+ 51Ω G0-G7
G0-G7 100pF
Rx1-
51Ω B0-B7
B0-B7
Rx2+ 51Ω
100pF
DE Rx2- DE
51Ω
Rx3+ 51Ω
100pF
Rx3-
51Ω
Host
CLK+ 51Ω
Graphics PLL 100pF
DCLK
CLK- PLL
Controller 51Ω Timing
Controller
LVDS Transmitter LVDS Receiver
THC63LVDM83A THC63LVDF84A
(LVDF83A)
R0~R7 : Pixel R Data

G0~G7 : Pixel G Data
B0~B7 : Pixel B Data
DE : Data enable signal
Note (1) The system must have the transmitter to drive the module.
Note (2) LVDS cable impedance shall be 50 ohms per signal line or about 100 ohms per twist-pair line when it is
used differentially.
16
Version 2.1
Approval
5.5 LVDS INTERFACE
TRANSMITTER INTERFACE RECEIVER TFT CONTROL

SIGNAL
THC63LVDM83A CONNECTOR THC63LVDF84A INPUT
SELLVDS= SELLVDS SELLVDS= SELLVDS

PIN INPUT Host TFT-LCD PIN OUTPUT
L or OPEN =H L or OPEN =H
R0 R2 51 TxIN0 27 Rx OUT0 R0 R2
R2 R4 54 TxIN2 TA OUT0+ Rx 0+ 30 Rx OUT2 R2 R4
R5 R7 3 TxIN6 TA OUT0- Rx 0- 35 Rx OUT6 R5 R7
G0 G2 4 TxIN7 37 Rx OUT7 G0 G2
G3 G5 11 TxIN12 TA OUT1+ Rx 1+ 43 Rx OUT12 G3 G5
G4 G6 12 TxIN13 45 Rx OUT13 G4 G6
G5 G7 14 TxIN14 46 Rx OUT14 G5 G7
B0 B2 15 TxIN15 TA OUT1- Rx 1- 47 Rx OUT15 B0 B2
B1 B3 19 TxIN18 51 Rx OUT18 B1 B3
24 B2 B4 20 TxIN19 53 Rx OUT19 B2 B4
bit B3 B5 22 TxIN20 54 Rx OUT20 B3 B5
B4 B6 23 TxIN21 TA OUT2+ Rx 2+ 55 Rx OUT21 B4 B6
B5 B7 24 TxIN22 1 Rx OUT22 B5 B7
DE DE 30 TxIN26 6 Rx OUT26 DE DE
R6 R0 50 TxIN27 TA OUT2- Rx 2- 7 Rx OUT27 R6 R0
G7 G1 10 TxIN11 42 Rx OUT11 G7 G1
B6 B0 16 TxIN16 TA OUT3+ Rx 3+ 49 Rx OUT16 B6 B0
B7 B1 18 TxIN17 50 Rx OUT17 B7 B1
RSVD 1 RSVD 1 25 TxIN23 2 Rx OUT23 NC NC
RSVD 2 RSVD 2 27 TxIN24 TA OUT3- Rx 3- 3 Rx OUT24 NC NC
RSVD 3 RSVD 3 28 TxIN25 5 Rx OUT25 NC NC
DCLK 31 TxCLK IN TxCLK OUT+ RxCLK IN+ 26 RxCLK OUT DCLK
TxCLK OUT- RxCLK IN-
R0~R7: Pixel R Data (7; MSB, 0; LSB)
G0~G7: Pixel G Data (7; MSB, 0; LSB)
B0~B7: Pixel B Data (7; MSB, 0; LSB)
DE: Data enable signal
Note (1) RSVD (reserved) pins on the transmitter shall be “H” or “L”.
17
Version 2.1
Approval
5.6 COLOR DATA INPUT ASSIGNMENT

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for
the color. The higher the binary input, the brighter the color. The table below provides the assignment of
color versus data input.
Data Signal
Color Red Green Blue
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0
Black 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Basic Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Colors Cyan 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Magenta 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Yellow 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
White 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Red(0) / Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(1) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(2) 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Gray
: : : : : : : : : : : : : : : : : : : : : : : : :
Scale
: : : : : : : : : : : : : : : : : : : : : : : : :
Of
Red(253) 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red
Red(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Red(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green(0) / Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Green(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
Green(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0
Gray
: : : : : : : : : : : : : : : : : : : : : : : : :
Scale
: : : : : : : : : : : : : : : : : : : : : : : : :
Of
Green(253) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1 0 0 0 0 0 0 0 0
Green
Green(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
Green(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
Blue(0) / Dark 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Blue(1) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
Blue(2) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0
Gray
: : : : : : : : : : : : : : : : : : : : : : : : :
Scale
: : : : : : : : : : : : : : : : : : : : : : : : :
Of
Blue(253) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 1
Blue
Blue(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
Blue(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Note (1) 0: Low Level Voltage, 1: High Level Voltage
18
Version 2.1
Approval
6. INTERFACE TIMING
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
The input signal timing specifications are shown as the following table and timing diagram.
Signal Item Symbol Min. Typ. Max. Unit Note
Frequency 1/Tc 60 74 82 MHZ
LVDS Receiver Clock Input cycle to
Trcl - - 200 ps
cycle jitter
Setup Time Tlvsu 600 - - ps
LVDS Receiver Data
Hold Time Tlvhd 600 - - ps
Frame Rate Fr5 47 50 53 Hz
Fr6 57 60 63 Hz
Vertical Active Display Term Total Tv 776 806 1000 Th Tv=Tvd+Tvb
Display Tvd 768 768 768 Th -
Blank Tvb 8 38 232 Th -
Total Th 1422 1560 2000 Tc Th=Thd+Thb
Horizontal Active Display Term Display Thd 1366 1366 1366 Tc -
Blank Thb 56 194 634 Tc -
Note (1) Since this module is operated in DE only mode, Hsync and Vsync input signals should be set to
low logic level. Otherwise, this module would operate abnormally.
INPUT SIGNAL TIMING DIAGRAM
Tv
Tvd
Tvb
DE
Th
DCLK
Tc
Thd
Thb
DE
DATA Valid display data (1366 clocks)
19
Version 2.1
Approval
LVDS RECEIVER INTERFACE TIMING DIAGRAM
Tc
RXCLK+/-
RXn+/-
Tlvsu
Tlvhd
1T 3T 5T 7T 9T 11T 13T
14 14 14 14 14 14 14
20
Version 2.1
Approval
6.2 POWER ON/OFF SEQUENCE

To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the diagram
below.
Power Supply 0.9 VCC 0.9 VCC
VCC
0.1VCC 0.1Vcc
0V
0.5T110ms T1 T3
0T250ms
0T350ms
1s T4 T2 T4
VALID
Signals
0V
Power On Power Off
Backlight (Recommended) 50% 50%

200msT5
100msT6
T5 T6
Power ON/OFF Sequence
Note (1) The supply voltage of the external system for the module input should follow the definition of Vcc.
Note (2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD
operation or the LCD turns off before the backlight turns off, the display may momentarily become
abnormal screen.
Note (3) In case of Vcc is in off level, please keep the level of input signals on the low or high impedance.
Note (4) T4 should be measured after the module has been fully discharged between power off and on period.
Note (5) Interface signal shall not be kept at high impedance when the power is on.
21
Version 2.1
Approval
7. OPTICAL CHARACTERISTICS
7.1 TEST CONDITIONS
Item Symbol Value Unit
o
Ambient Temperature Ta 25±2 C
Ambient Humidity Ha 50±10 %RH
Supply Voltage VCC 12.0 V
Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"
Lamp Current IL 5.0 ± 0.5 mA
Oscillating Frequency (Inverter) FW 58 ± 3 KHz
Vertical Frame Rate Fr 60 Hz
7.2 OPTICAL SPECIFICATIONS

The relative measurement methods of optical characteristics are shown in 7.2. The following items should
be measured under the test conditions described in 7.1 and stable environment shown in Note (6).
Item Symbol Condition Min. Typ. Max. Unit Note
Contrast Ratio CR 600 800 - - (2)
TR - 3 5
Response Time ms (3)
TF - 5 8
Center Luminance of White LC 400 500 - cd/m2
(4)
Average Luminance of White LAVE 350 450 - cd/m2
100%
-
- - 1.3 Dimming
θx=0°, θY =0°
Duty (7)
White Variation δW 30%
Viewing Angle at - - 1.5 - Dimming
Duty (7)
Normal Direction
Cross Talk CT - - 4 % (5)
Rx 0.637 -
Red
Ry 0.329 -
Gx 0.270 -
Green
Gy Typ. 0.596 Typ. -
Color (6)
Bx -0.03 0.150 +0.03 -
Chromaticity Blue
By 0.062 -
Wx 0.280
White Target
Wy 0.285
Color Gamut CG 68 72 - % NTSC
θx+ 70 80
Horizontal
Viewing θx- 70 80
CR≥10 Deg. (1)
Angle θY+ 70 80
Vertical
θY- 60 70
22
Version 2.1
Approval
Note (1) Definition of Viewing Angle (θx, θy):

Viewing angles are measured by EZ-Contrast 160R (Eldim)
Normal
θx = θy = 0º
θy- θy+
θX- = 90º x- 12 o’clock direction

y+
θx− θy+ = 90º
θx+
6 o’clock
y- x+ θX+ = 90º
θy- = 90º
Note (2) Definition of Contrast Ratio (CR) :

The contrast ratio can be calculated by the following expression.
Contrast Ratio (CR) = L255 / L0
L255: Luminance of gray level 255
L 0: Luminance of gray level 0
CR = CR (5), where CR (X) is corresponding to the Contrast Ratio of the point X at the figure in Note
(7).
Note (3) Definition of Response Time (TR, TF) :
Gray Level 255 Gray Level 255
100%
90%
Optical
Gray Level 0
Response
10%
0%
Time
TF
TR
23
Version 2.1
Approval
Note (4) Definition of Luminance of White (LC , LAVE):

Measure the luminance of gray level 255 at center point and 5 points
LC = L (5),
LAVE = [L (1)+ L (2)+ L (3)+ L (4)+ L (5)] / 5,
where L (X) is corresponding to the luminance of the point X at the figure in Note (7).
Note (5) Definition of Cross Talk (CT):
CT = | YB – YA | / YA × 100 (%)
Where:
YA = Luminance of measured location without gray level 0 pattern (cd/m2)
YB = Luminance of measured location with gray level 0 pattern (cd/m2)
(0, 0) Active Area (0, 0)

Active Area
YA, U (D/2,W/8) YB, U (D/2,W/8)
(D/4,W/4)
YA, L (D/8,W/2) YB, L (D/8,W/2) YB, R (7D/8,W/2)

Gray 128 Gray 0
YA, R (7D/8,W/2)
(3D/4,3W/4)
YA, D (D/2,7W/8)
YB, D (D/2,7W/8) Gray 128
(D,W) (D,W)
Note (6) Measurement Setup:

The LCD module should be stabilized at given temperature for 1 hour to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be
executed after lighting Backlight for 1 hour in a windless room.
LCD Module
LCD Panel
Center of the Screen Display Color Analyzer

(Minolta CA210)
Light Shield Room

(Ambient Luminance < 2 lux)
24
Version 2.1
Approval
Note (7) Definition of White Variation (δW):

PWM input signal for dimming duty refer to 3.2.2 INVERTER CHARACTERISTICS.
Measure the luminance of gray level 255 at 5 points
δW = Maximum [L (1), L (2), L (3), L (4), L (5)] / Minimum [L (1), L (2), L (3), L (4), L (5)]
Horizontal Line
D
D/4 D/2 3D/4
Vertical Line
W/4 1 2
W W/2 5 X : Test Point

X=1 to 5
3W/4 3 4
Active Area
25
Version 2.1
Approval
8. DEFINITION OF LABELS
8.1 CMO MODULE LABEL
The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation.
E207943
CHI MEI MADE IN TAIWAN
OPTOELECTRONICS V260B1 -L03 Rev. XX
XXXXXXXYMDLNNNN
(a) Model Name: V260B1-L03

(b) Revision: Rev. XX, for example: A0, A1… B1, B2… or C1, C2…etc.
(c) Serial ID: X X X X X X X Y M D L N N N N
Serial No.
Product Line
Year, Month, Date
CMO Internal Use
CMO Internal Use
Revision
CMO Internal Use

Serial ID includes the information as below:
(a) Manufactured Date: Year: 1~9, for 2001~2009
Month: 1~9, A~C, for Jan. ~ Dec.
Day: 1~9, A~Y, for 1st to 31st, exclude I ,O, and U.
(b) Revision Code: Cover all the change
(c) Serial No.: Manufacturing sequence of product
(d) Product Line: 1 -> Line1, 2 -> Line 2, …etc.
26
Version 2.1
Approval
9. PACKAGING
9.1 PACKING SPECIFICATIONS
(1) 5 LCD TV Modules / Carton
(2) Carton Dimensions : 742(L) X 399 (W) X 480 (H)
(3) Weight : Approximately 26.5Kg ( 5 Modules Per Carton)
9.2 PACKING METHOD

Figures 8-1 and 8-2 are the packing method
LCD TV Module
Anti-Static Bag
Cushion(Bottom)
2 pcs Drier
Carton
Carton Label
Figure.8-1 Packing Method
27
Version 2.1
Approval
Sea Transportation
Corner Protector:L1850*50*50mm
L11300*50*50mm
Pallet:L1150*W1150*H140mm
Pallet Stack:L1150*W1150*H2060mm
Gross:440kg
PE Sheet
Film
Carton Label
PP Belt
Figure. 8-2 Packing Method
28
Version 2.1
Approval
10. PRECAUTIONS
10.1 ASSEMBLY AND HANDLING PRECAUTIONS
(1) Do not apply rough force such as bending or twisting to the module during assembly.
(2) It is recommended to assemble or to install a module into the user’s system in clean working areas.
The dust and oil may cause electrical short or worsen the polarizer.
(3) Do not apply pressure or impulse to the module to prevent the damage of LCD panel and backlight.
(4) Always follow the correct power-on sequence when the LCD module is turned on. This can prevent the
damage and latch-up of the CMOS LSI chips.
(5) Do not plug in or pull out the I/F connector while the module is in operation.
(6) Do not disassemble the module.
(7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and
easily scratched.
(8) Moisture can easily penetrate into LCD module and may cause the damage during operation.
(9) High temperature or humidity may deteriorate the performance of LCD module. Please store LCD
modules in the specified storage conditions.
(10) When ambient temperature is lower than 10ºC, the display quality might be reduced. For example, the
response time will become slow, and the starting voltage of CCFL will be higher than that of room
temperature.
10.2 SAFETY PRECAUTIONS

(1) The startup voltage of a backlight is over 1000 Volts. It may cause an electrical shock while assembling
with the inverter. Do not disassemble the module or insert anything into the backlight unit.
(2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
(3) After the module’s end of life, it is not harmful in case of normal operation and storage.
10.3 STORAGE PRECAUTIONS

When storing modules as spares for a long time, the following precaution is necessary.
(1) Do not leave the module in high temperature, and high humidity for a long time.
It is highly recommended to store the module with temperature from 0 to 35at normal humidity without
condensation.
(2) The module shall be stored in dark place. Do not store the TFT-LCD module in direct sunlight or fluorescent
light.
29
Version 2.1
Approval
11. REGULATORY STANDARDS

11.1 SAFTY
Regulatory Item Standard
UL UL 60950-1: 2003
Information Technology equipment cUL CAN/CSA C22.2 No.60950-1-03
CB IEC 60950-1:2001
UL UL 60065: 2003
Audio/Video Apparatus cUL CAN/CSA C22.2 No.60065-03
CB IEC 60065:2001
30
Version 2.1
Approval
12. MECHANICAL CHARACTERISTICS

CHI MEI
31
Version 2.1
32
HIGH VOLTAGE
C AU TION
RI SK OF EL ECT RIC S H OCK . COL D CATH ODE FL UORESCENT L AMP IN LCD PANEL CONTAI NS A SMALL AMOUNT OF
D I SCONNECT T H E EL ECT RIC MERCURY PLEASE FOL LOW LOCAL ORDIN ANCES OR REG UL ATI ONS FOR DISPOSAL .
POWER BEF ORE S ERVI CI NG.
CHI MEI
Version 2.1
Approval

Approval

CHI MEI
33
Version 2.1
Approval
13. APPENDIX
34
Version 2.1

V260B1 L03 ChiMei PDF

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

V260B1 L03 ChiMei PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

V260B1 L03 ChiMei PDF

Uploaded by

Copyright:

Available Formats

Issued Date: 7, May 2007

Model No.: V260B1 - L03

TFT LCD Approval Specification

QRA Dept. Product Development Div.

LCD TV Marketing and Product Management Div.

1. GENERAL DESCRIPTION ------------------------------------------------------- 4

11. REGULATORY STANDARDS ------------------------------------------------------- 30

1.4 GENERAL SPECIFICATI0NS

1.5 MECHANICAL SPECIFICATIONS

2. ABSOLUTE MAXIMUM RATINGS

Relative Humidity (%RH)

2.2 PACKAGE STORAGE

2.3 ELECTRICAL ABSOLUTE RATINGS

2.3.2 BACKLIGHT UNIT

Vcc rising time is 470us

a. White Pattern b. Black Pattern

Active Area Active Area

c. Vertical Stripe Pattern

3.2 BACKLIGHT INVERTER UNIT

3.2.2 INVERTER CHARACTERISTICS (Ta = 25 ± 2 ºC)

Oscillating Frequency FW 55 58 61 kHz

3.2.3 INVERTER INTERTFACE CHARACTERISTICS

INVERTER INTERFACE IMPEDANCE

5. INTERFACE PIN CONNECTION

5.2 BACKLIGHT UNIT

CN2 (Housing): ZHR-2 (JST) or Equivalent

5.3 INVERTER UNIT

CN2(Header): S2B-ZR-SM4A-TF or Equivalent

CN3-CN8 (Header): CP042BP1MRO-LF (CviLux) or Equivalent

Note (1) Floating of any control signal is not allowed.

5.4 BLOCK DIAGRAM OF INTERFACE

R0~R7 : Pixel R Data

5.5 LVDS INTERFACE

TRANSMITTER INTERFACE RECEIVER TFT CONTROL

SELLVDS= SELLVDS SELLVDS= SELLVDS

5.6 COLOR DATA INPUT ASSIGNMENT

INPUT SIGNAL TIMING DIAGRAM

DATA Valid display data (1366 clocks)

LVDS RECEIVER INTERFACE TIMING DIAGRAM

6.2 POWER ON/OFF SEQUENCE

Power Supply 0.9 VCC 0.9 VCC

Power On Power Off

Backlight (Recommended) 50% 50%

Power ON/OFF Sequence

7.2 OPTICAL SPECIFICATIONS

Note (1) Definition of Viewing Angle (θx, θy):

θX- = 90º x- 12 o’clock direction

Note (2) Definition of Contrast Ratio (CR) :

Gray Level 255 Gray Level 255

Note (4) Definition of Luminance of White (LC , LAVE):

(0, 0) Active Area (0, 0)

YA, L (D/8,W/2) YB, L (D/8,W/2) YB, R (7D/8,W/2)

Note (6) Measurement Setup:

Center of the Screen Display Color Analyzer

Light Shield Room

Note (7) Definition of White Variation (δW):

W W/2 5 X : Test Point

(a) Model Name: V260B1-L03

CHI MEI