Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 1K views

    Inala Power Wizard 1.0 Olympain

    Uploaded by

    Antonio Martin
    The document provides instructions for connecting a generator controller and configuring its settings. It details the connections for various generator signals and controls. It also provides steps to program the controller's digital selectors and change the language setting.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd

    Inala Power Wizard 1.0 Olympain

    Uploaded by

    Antonio Martin
    1K views4 pages
    The document provides instructions for connecting a generator controller and configuring its settings. It details the connections for various generator signals and controls. It also provides steps to program the controller's digital selectors and change the language setting.

    Original Description:

    Inala Power Wizard 1.0 Olympain

    Copyright

    © © All Rights Reserved

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides instructions for connecting a generator controller and configuring its settings. It details the connections for various generator signals and controls. It also provides steps to program the controller's digital selectors and change the language setting.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    1K views4 pages

    Inala Power Wizard 1.0 Olympain

    Uploaded by

    Antonio Martin
    The document provides instructions for connecting a generator controller and configuring its settings. It details the connections for various generator signals and controls. It also provides steps to program the controller's digital selectors and change the language setting.

    Copyright:

    © All Rights Reserved
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    You are on page 1of 4

    Connections For Power Wizard 1.

    0 FG
    Wilson/Olympian

    Gen Fault Wire no 88 on the top terminal strip (Fig.1)


    Gen Door From switch supplied.
    Gen Run Wire no 90 on the top terminal strip (Fig.1)
    Gen on Load Not supported
    Gen Temp Not supported
    Gen Oil Press Not supported
    Emergency Stop From switch on the side where +12Volt signal falls away
    when pushed, if switch is available.
    Gen Low Fuel Not connected as Inala fuel probe is installed.
    Remote Start Wire no 5&24 – At the bottom terminal strip connection
    Points 1 and 2 (Fig.2)
    Mains on load Not supported
    Remote Reset Not supported
    12Volt Supply +12V on terminal block wire 1+ position 1
    Ground on terminal strip wire number 5 (Fig.1)
    Direct on battery is the best.
    When doing the connections the wires on positions 40 and 27 on the controller side
    (marked on the connector) and with the numbers 7 on both wires should be cut off and
    connected together.
    Connect this joint wires to ground number 5 on terminal strip. (Fig.3)

    The controller should be programmed for the following configuration.

    Digital selector # 4 should be configured for user 3 (Generator Running)


    Digital selector # 3 should be configured for user 1 (Generator Alarm)

    To program these parameters follow the following steps.


    1) Go to Main Menu the arrow.

    2) Use the  arrow to go to Configure.


    3) Press the  arrow to enter the Configure sub menu.

    4) Use the  arrow to go to Setpoints.

    5) Press the  arrow to enter the Setpoints sub menu.

    6) Use the  arrow to go to Other.

    7) Press the  arrow to enter the Other sub menu.

    8) Use the  arrow to go to Digital Selectors.

    9) Press the  arrow to enter the Digital Selectors sub menu.

    10) Use the  arrow to go to Digital Selector #3.

    11) Press the  arrow to select Digital Selector #3 to be changed.

    12) Press the  arrow again to select the User for Digital Selector #3.

    13) Use  arrows to change to User 1 for Digital Selector #3.

    14) Press the  arrow to set new setting.

    15) Press the  to go back to Digital Selectors.

    16) Use the  arrow to go to Digital Selector #4.

    17) Press the  arrow to select Digital Selector #4 to be changed.

    18) Press the  arrow again to select the User for Digital Selector #4.
    19) Use  arrows to change to User 3 for Digital Selector #4.
    20) Press the  arrow to set new setting.
    21) Press the Engine Logo button to exit menu.

    Make sure that you put controller in the Auto Mode after the installation by
    pressing the yellow button in the middle.

    To change language from French to English


    1) Go to Main Menu the arrow.

    2) Use the  arrow to go down 6 places to Preferences


    3) Press the  arrow to enter the menu.

    4) Use the  arrow to go down 5 places to Language.

    5) Press the  arrow to enter menu and select English.

    Fig.1

    Gen Fault
    Wire no 88

    Gen Running
    Wire no 90

    12V Supply
    Wires 1+ and
    5 negative
    Fig.2

    Remote Start
    Wires no 5 / 24

    Fig.3

    Wires on position 27 and 40 on controller, cut and join


    together then connect to Battery negative, number 5 on top
    terminal strip

    You might also like