IOM:B3

10.07

®
Series B3 ROOTS Meters
Models:
Series B3: 8C175 - 56M175
Series B3-HP: 1M300 - 3M300
WARRANTY
Seller warrants that (i) its products will, at the F.O.B. point, be free from defects in materials and work-
manship and (ii) its services will, when performed, be of good quality.
Any claim for failure to conform to the above and foregoing warranty must be made immediately upon
discovery, but in any event, within eighteen (18) months following delivery of the specified product at the
F.O.B. point or twelve (12) months after installation whichever is earlier, or twelve (12) months after per-
formance of the specified services. Warranties may be extended in time pursuant to Seller’s written war-
ranties, provided payment has been received for the extension. Defective and nonconforming items must
be held for Seller’s inspection and returned at Seller’s request, freight prepaid, to the original F.O.B. point.
Upon Buyer’s submission of a claim as provided above and substantiation, Seller shall, at its option (i)
either repair or replace its nonconforming product or correct or reperform its nonconforming services, as
applicable, or (ii) refund an equitable portion of the purchase price attributable to such nonconforming
products or services. Seller shall not be liable for the cost of removal or installation of materials or any
unauthorized warranty work, nor shall Seller be responsible for any transportation cost, unless expressly
authorized in writing by Seller. Any products or materials replaced by Seller will become the property of
Seller. Repair or replacement of products, or correction or reperformance of services, or refund of an
equitable portion of the purchase price shall be Seller’s only obligation and the sole and exclusive
remedy of Buyer in the event of a failure to conform to the foregoing warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES (EXCEPT THAT
OF TITLE) EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A
PARTICULAR PURPOSE.

Dresser ROOTS Meters and Instruments

Dresser, Inc.
Post Office Box 42176
Houston, Texas 77242
Telephone: 832.590.2303
Facsimile: 832.590.2494
www.rootsmeters.com
2
TABLE OF CONTENTS

WARRANTY 2 ACCESSORY UNIT REMOVAL &

CONVERSION PROCEDURES 17-23
TABLE OF CONTENTS 3
• Removing the Accessory Unit
RECEIVING, HANDLING & STORAGE 4
• Removing the Gear Reduction
INTRODUCTION 4-5
• Replacing the Gear Reduction
• Use and Limitations
• Installing the Accessory Unit
• Operating Principle
• ID Side Inlet to Top Inlet Conversion
GENERAL DESIGN CHARACTERISTICS 5
• Changing the ID Rotational Direction
METER BODY 5
• Installing a Solid State Pulser
ACCESSORY UNIT 6-10
• Installing an ICEX
• Counter (CTR)
• Counter with Instrument Drive (CD) • Installing an AMR Adapter
• Temperature Compensated (TC) TESTING 23-29
• Temperature Compensated with Instrument
Drive (TD) • General
• Pulser Version • Differential Test
• Counter with Electronic Transmitter (ICEX) • Establishing Baseline Curves
• Counter/TC AMR (Automatic Meter • Differential Test Procedure
Reading) version
• Proving Operations
IMPERIAL/METRIC ODOMETERS 11
• TC Unit Operational Check
TEST WHEEL 12
• Procedure for the TC Unit Operational Check
TC ODOMETER 12
• Calculating Theoretical Counts
METER INSTALLATION 12-16
TROUBLE SHOOTING CHECKLIST 29
• Piping Configurations
SIZING CHARTS 30-31
• Placing Meter In Line
• Oil Capacities
• Meter Start-Up
INSPECTION & MAINTENANCE 16
• Accessory Unit
• Lubrication
• Meter Level
• Meter Testing
• Cleaning and Flushing

3
AT TIME OF DELIVERY STORAGE/INITIAL TESTING
1. Check the packing list to account for all items If the meter is not tested or installed soon after receipt,
received. store in a dry location in the original shipping container
for protection. Make sure the box remains horizontal with
2. Inspect each item for damage.
the arrow pointing up. Leave the protective caps installed
3. Record any visible damage or shortages on the in the meter. The caps will provide reasonable protection
delivery record. against dust.
• File a claim with the carrier. “Checking for free rotation” (Refer Figure 12) does not
• Notify your ROOTS® meter supplier necessarily mean the meter will pass a test after sitting
immediately. on the shelf for a year or two. A small amount of oil is
Do not accept any shipment that has evidence of applied to the bearings of new or remanufactured
mishandling in transit without making an immediate meters, but this is only sufficient for factory testing.
inspection of package for damage. All new meters The oil in the bearings can coagulate over time. This
should be checked for free rotation soon after condition may impact meter test performance until the
arrival as damage to internal working parts can bearings loosen up. Dresser recommends a drop or two
exist without obvious external evidence. of oil be applied to each bearing and that the meter be
Should any serious problems be encountered during run at a flow rate between 80% & 100% of meter
installation or initial operation of the meter, notify your capacity for two minutes or until the meter is
ROOTS® meter supplier immediately. running smoothly.
Do not attempt repairs or adjustments, as doing so INTRODUCTION
may be a basis for voiding all claims for warranty.
Use and Limitations
When reporting a suspected problem, please provide ROOTS® Meters are suitable for handling most types of
the following information: clean, dry, common gases at either constant or varying
• Your Purchase Order Number and/or flow rates. The meter is not suitable for handling liquids.
Dresser’s Sales Order Number Measurement accuracy and life expectancy may be
• The Meter Model, Serial Number and Bill of affected by dirt or other types of foreign material in
Material Number the gas stream.
(This information can been located on the blue name Meters of standard construction are not suitable for
plate that is between the differential plugs on the meter handling acetylene, biogas or sewage gas. Specially
body) constructed meters compatible with these and other
• The Accessory Unit Serial Number gases are available. Please contact your ROOTS® meter
supplier for details and to request publication TS:SSM.
• A Description of the problem
• Application information, such as gas type,
pressure, temperature, and flow characteristics
Our Product Services Department offers professional
services for all ROOTS® products. Authorization for
return is required for all products shipped to the
Factory for repair, calibration, warranty, exchange or
credit. To obtain authorization an RMA number for
return of ROOTS® products must be issued. Please
contact your ROOTS® meter supplier. All returns
should be packaged in an original-type shipping con-
tainer if available or shipping material that will protect
the product. Note: Do not use peanut packing foam
because fragments may enter the measuring chamber.

4
Operating Principle GENERAL DESIGN CHARACTERISTICS
As shown in Figure 1, two contra-rotating impellers
ROOTS® Meters are manufactured in accordance with
of two-lobe or “figure 8” contour are encased within
the American National Standard specification
a rigid measuring chamber, with inlet and outlet
ANSI/ASC-B109.3 for Rotary Type Gas Displacement
connections on opposite sides. Precision machined
Meters. The flanged inlet and outlet connections
timing gears keep the impellers in correct relative
position. Optimal operating clearances between conform dimensionally to ANSI/ASME standard B16.5.
the impellers, cylinder, and headplates provide a The operating temperature range is from -40°F to
continuous, non-contacting seal. +140° F (-40° C to +60° C).
Every meter is static pressure tested at the factory at
200% of its MAOP (Maximum Allowable Operating
Pressure) and leak tested at 125% of MAOP in accor-
dance with ASME Boiler and Pressure Vessel Codes.
The internal aluminum parts of the measurement
chamber (i.e., impellers and headplates) are hard-coat
anodized for added corrosion and abrasion resistance.
The external surface and the two end covers are clear
Figure 1 - Impellers rotating inside meter cylinder. coat anodized.
The meter rating is expressed in hundreds (C) or
Because of this design, the gas at the meter’s inlet is
thousands (M) of Actual Cubic Feet per Hour (ACFH),
effectively isolated from the gas at the outlet. During
or in Cubic Meters per Hour (m3H). Actual displaced
impeller rotation, the precision machined measuring
volume measurement is completely independent of
chamber traps a known volume of gas between the
the gas specific gravity, temperature, and pressure and
impeller and the adjacent cylinder wall. The meter
can be easily converted to volume at Standard condi-
will measure and pass four equal gas volumes with
tions for elevated pressure and varying temperature
each complete revolution of the impellers.
by application of the Gas Laws (reference Dresser
The sum total of the four volumes is the publication RM-135).
“volume per revolution”. The volume is indicated
Refer to a meter sizing chart for capacity ratings at
in Engineering units represented in cubic feet
elevated line pressures or varying line pressures since
(or cubic meters).
this will assist in properly sizing the meter.
Volumetric accuracy of the ROOTS® meter is
permanent and non-adjustable. Measurement METER BODY
characteristics are established by the shape and
Meter Size Operating Connection Types
the precise machining of non-wearing fixed and
Pressures ANSI Class
rotating parts.
8C -56M* 175 PSIG 150# FF
A meter’s rated capacity is the maximum flow rate
(1200 kPa)
at which the meter may be operated and is deter-
mined by the dynamic loads acting on the moving 23M232 232 PSIG 150# FF
parts of the meter. These loads are primarily related (1600 kPa)
to meter RPM, and secondarily to the metering
1M300/3M300 300 PSIG 300 # FF
pressure. The standard volume capacity of a rotary
meter increases directly with changes in absolute * Upon special request:
line pressure and inversely with changes in absolute Meter sizes 8C through 2M are available with 1-1/2” NPT nippled connections.
Sizes 8C through 5M are available with a MAOP rating of 200 PSIG (1380 kPa).
line temperature.
Major components of these meters are machined from
cast or extruded aluminum for a combination of
strength and weight reduction.

5
ACCESSORY UNIT
Totalization of the volume is performed by a magneti-
cally coupled gear reduction unit referred to as the
Series 3 Accessory Unit. These units are permanently
lubricated for long life and maintenance-free operation.
They register displaced volume in actual cubic feet
(ACF) or actual cubic meters (m3). The Series 3
Accessory Unit is isolated from the pressure vessel
and is not pressurized. This modular design allows
interchangeability of Accessory Units on Series B
meter bodies of the same size.
Figure 3 - Non-Compensated Series 3 Imperial unit
Counter (CTR) Version
odometer for 8C (Top) and 16M (Bottom).
The Series 3 CTR units register volume in actual cubic
feet (ACF) or actual cubic meters (m3) on an 8 digit Counter with Instrument Drive (CD) Version
odometer. The Series 3 CTR cover is molded of
optical quality Lexan® with a quad ring seal. The The Counter with Instrument Drive (CD) unit uses the
cover’s smooth cylindrical design easily sheds rain CTR assembly above, with a specially designed Lexan®
and resists accumulations of snow, ice and dirt. cover and an Instrument Drive support assembly. The
Instrument Drive (ID) support is mechanically linked
NOTE: Reference the “Reading the Odometer” section to the gear reduction of the CTR unit and rotates the
for instructions on reading the Series 3 Accessory Unit. instrument ‘drive dog’ at the ID output. One revolution
of the instrument drive dog represents a specific
displaced volume measured by the meter, depending
upon meter size. Refer to Table 1 for Instrument Drive
Rates for that particular meter size.
Lexan® is a registered trademark of the General Electric Company.

Meter Size Volume/Revolution

Imperial 8C thru 11M 10 cu. ft./rev.
16M thru 56M 100 cu. ft./rev.
Metric 8C thru 3M 0,1 m3/rev.
5M thru 38M 1,0 m3/rev.
56M 10,0 m3/rev.
Figure 2 - Series 3 Accessories do not require oil.
(CTR Version shown) Table 1 - Instrument Drive Rates for Series 3 Counter
with Instrument Drive (CD) accessories.
The 8C through 11M odometers with Imperial units of
measure (actual cubic feet) have five exposed digits. The instrument mounting section of the Instrument
As an industry standard, the first digit on the left of the Drive (ID) housing can be easily rotated 90° when
odometer is typically concealed with an opaque mask. changing the meter from Top to Side inlet or vice
Translucent masks are normally specified to cover the versa. (Refer to “ACCESSORY UNIT REMOVAL &
two right-most digits. For the 16M through 56M CONVERSION PROCEDURES, Side Inlet to Top Inlet
odometers with Imperial units, six digits are exposed. Conversion”.) A cover plate on the Instrument Drive
Again, the first digit on the left of the odometer is typi- support housing allows access to the bevel gears for
cally concealed with an opaque mask while only the a change of rotation of the drive dog - from clockwise
right-most digit is covered with a translucent mask. to counterclockwise rotation or vice versa. (Refer to
The odometers for 8C and 16M meters are shown in “ACCESSORY UNIT REMOVAL & CONVERSION
Figure 3. PROCEDURES, Changing the Rotational Direction).

6
of the Instrument Drive”.) A decal located on the ID Pulser Version
housing indicates output drive volume. There is also ROOTS® Pulsers generate low frequency pulses for
a universal instrument mounting plate installed on the remote volume data collection. Pulsers are available
ID support. with Single or Dual Mil-Spec (MS) circular connectors,
NOTE: Lubrication is NOT required for the ID a liquid tight conduit fitting, or a cable gland connec-
support housing. tion as shown in Figure 4.
The CTR unit’s output represents Non-Compensated
Temperature Compensated (TC) Version volume only. The TC unit provides two outputs; one
Temperature compensation is accomplished by a representing non-compensated volume, the second
mechanical computational device with a bi-metallic representing temperature compensated volume.
probe located in a sealed temperature well at the
The pulse rate for any factory installed accessory unit
meter inlet. This system allows Series 3 Temperature
can be identified by the decal located on the Pulser’s
Compensated (TC) units to provide corrected
Lexan® cover or by referencing Table 3. The tempera-
volume readings on gas temperatures ranging
ture, electrical and current rating is located on another
from -20°F to +120°F (-29°C and +49°C).
label which is also on the Lexan® cover. Table 4
NOTE: Temperature compensated meters update the provides the wiring guide for series 3 Pulsers.
temperature compensated odometer intermittently.
For additional information, request Pulser specification
All standard design 8C175 through 16M175 and
sheet TS:SSP and drawing number 057159-000.
8C200 through 5M200 Series B meter bodies are
shipped with a temperature probe well installed.
This allows for an easy and low cost conversion
from a non-compensated meter to temperature
compensated meter.
NOTE: Reference the “READING THE ODOMETER”
section for instructions on reading the Series 3
Accessory Unit.

Temperature Compensated with Instrument Drive

(TD) Version Conduit Cable Gland
The Temperature Compensated with Instrument Drive
(TD) Accessory Unit uses a standard TC unit with an
Instrument Drive (ID) support installed. However, one
revolution of the ‘drive dog’ now represents a gas vol-
ume corrected to a contract Base temperature of 60°F
(or 15°C). The drive rates are provided in Table 2.
NOTE: Rotation of the “Drive Dog” is tied directly to
the update of the compensated odometer and is
therefore, intermittent in nature.
Mil-Spec Circular
Meter Size Volume/Revolution Connector or
Amphenol
Imperial 8C thru 11M 100 cu. ft./rev.
16M 1000 cu. ft./rev.
Figure 4 - Pulser Connector Versions
Metric 8C thru 3M 1 m3/rev.
5M thru 16M 10 m3/rev.
Table 2 - Instrument Drive rates for Series 3
Temperature Compensated Accessory Unit with
Instrument Drive (TD).

7
Table 3 - The Pulse Outputs for Series 3 Pulsers

Imperial Imperial Metric

Series B Series 3 (Cubic Feet) (Cubic Feet) (Cubic Meter)
Meter Size Accessory Non-Compensated Compensated Non-Compensated
8C-3M CTR 10 cf — 0,1 m3
5M-11M CTR 10 cf — 1,0 m3
16M-38M CTR 100 cf — 1,0 m3
56M CTR 100 cf — 10,0 m3
8C-3M TC 10 cf 10 cf* 0,1 m3
5M-11M TC 10 cf 10 cf* 1,0 m3
16M TC 100 cf 100 cf* 1,0 m3

Table 4 - The Wiring Guide for Series 3 Pulsers

Non-Compensated Temperature Compensated

Signal Signal
Normally Normally
Pulser Pulser Connection Type Open Common Normally Open Common Normally
Type (Signal) Closed (Signal) Closed
ICPWS MSC MS Style Circular Connection A B C — — —
ICPWD MSC Two MS Style Circular Connections A B C — — —
ICPWS CBG Cable Gland with Leads (Pig Tail) Brown Green Red — — —
ICPWD CBG Two Cable Glands with Leads (Pig Tail) Brown Green Red — — —
ICPWX CND Conduit Compression Coupling with Lead (Pig Tail) Brown Green Red — — —

ITPWS MSC MS Style Circular Connection A B C D E F

ITPWD MSC Two MS Style Circular Connections A B C D E F
ITPWS CBG Cable Gland with Leads (Pig Tail) Brown Green Red White Black Blue
ITPWD CBG Two Cable Glands with Leads (Pig Tail) Brown Green Red White Black Blue
ITPWX CND Conduit Compression Coupling with Lead (Pig Tail) Brown Green Red White Black Blue

8
Counter with Electronic Transmitter (ICEX) Version The ICEX is available with a Single MS style circular
Like the ROOTS Solid State Pulsers, ICEX Meters
® connector, a liquid tight conduit fitting, or a cable
(Integral Counters with Electronic Transmitters) have gland connection (As shown previously in Figure 4).
a magnetically driven Pulser inside the cover. It gener- Table 5 provides wiring information for the ICEX.
ates a single channel high frequency pulse. This allows NOTE: As the magnet rotates on the high speed shaft,
for remote collection of volume while also providing a a sensor within the ICEX housing detects a change in
pulse rate suitable for determination of flow rate. Pulse the magnetic field.
rates for various meter sizes are shown in Table 6.

Table 5 - Wiring guide for Series 3 ICEX.

ICEX Connection Normally Open Common
Type (Signal)
MS Style Circular Connection A B
Conduit with Leads White Black
Cable Gland with Leads White Black

Figure 5 - Series 3 ICEX

Table 6 - Pulse outputs for ICEX Accessory Units in relation to meter sizes.

Meter Freq. Volume per Pulse Pulses per Volume* Flow Rate
Type (Hz) (CF) (m3) (CF) (m3) (ACFH)
8C175 120 0.001852 0,000052439 540 19070 800
11C175 146.67 0.002083 0,000058993 480 16951 1,100
15C175 166.67 0.002500 0,000070792 400 14126 1,500
2M175 111.11 0.005000 0,000141584 200 7063 2,000
3M175 133.33 0.006250 0,000176980 160 5650 3,000
5M175 150.00 0.009259 0,000262193 108 3814 5,000
7M175 124.45 0.015625 0,000442451 64 2260 7,000
11M175 122.22 0.025000 0,000707921 40 1413 11,000
16M175 120.00 0.037037 0,001048772 27 953 16,000
23M232 127.78 0.050000 0,001415843 20 706 23,000
23M175 69 0.092593 0,002621931 10.8 381 23,000
38M175 76 0.138889 0,003932896 7.2 254 38,000
56M175 89.60 0.173611 0,004916120 5.8 203 56,000
1M300 55.55 0.005000 0,000141584 200 7063 1,000
3M300 133.33 0.006250 0,000176980 160 5650 3,000
1M740 75.00 0.003704 0,000104877 270 9535 1,000
3M740 166.67 0.005000 0,000141584 200 7063 3,000
1M1480 75.00 0.003704 0,000104877 270 9535 1,000
3M1480 166.67 0.005000 0,000141584 200 7063 3,000
5M1480 100.00 0.013889 0,000393290 72 2543 5,000
7M1480 124.45 0.015625 0,000442451 64 2260 7,000
* Pulse per volume rounded to nearest whole number. For calculation purposes, use volume per pulse.

9
Counter/TC Automatic Meter Reading (AMR) Adapter Version

This design utilizes a Series 3 Lexan® cover with an The AMR Adapter consists of a Lexan cover, an
opening to engage the residential AMR module in a adapter “puck” (with coupling), an adapter plate and a
direct drive link to the gear reduction unit. The direct drive dog. It is universal up to the adapter plate and
drive AMR Adapter offers a solution for Series B3 CTR drive dog, which are specific for the residential meter
or TC meters in applications that require the adapta- type AMR device to be mounted (American or
tion of a residential style AMR. The AMR Adapter is Invesys/Sensus/Rockwell) and the type of AMR
available as a conversion kit for field installation or can module being used (Itron, Badger, Trace, Cellnet, etc.)
be factory installed on the Series B3 ROOTS® Meter. Programming Rates for various meter sizes are shown
in Table 7.

Figure 7 - American Footprint AMR Adapter installed

on a 2M ROOTS Meter (shown with Residential ERT
attached).

Figure 6 - American & Invensys Footprint AMR Adapters

Table 7 - S3 Meter Drive Rates for Direct Drive AMR Programming

Meter Size CTR Meter Drive Rate TC Meter Drive Rate

cu. ft./rev. cu. ft./rev.
8C175 10 100
11C175 10 100
15C175 10 100
2M175 10 100
3M175 10 100
5M175 10 100
7M175 10 100
11M175 10 100
16M175 100 1000
23M175 100 N/A
38M175 100 N/A
56M175 100 N/A

10
READING THE ODOMETER METRIC ODOMETERS

IMPERIAL ODOMETERS Examples of metric odometers are shown in Figure 9. -

Non-Compensated Series 3 Metric Unit odometers for
As an industry standard, the first digit on the left of 8C (Top), 16M (Middle), and 56M (Bottom).
the odometer is typically concealed with an opaque
(black) mask. Translucent (see through) blue masks When reading an 8C through 3M odometer (Figure 9a),
typically cover any digits to the right that represent the six digits between the arrows on the nameplate
less than 100 cubic feet. “202597” are equal to cubic meters.

When reading an 8C through 11M odometer (Figure NOTE: If the last two digits “39” to the right of the
8a), the five exposed digits “02576” between the comma were included in the reading, the odometer
arrows on the nameplate are typically multiplied by in Figure 9a would indicate a volume of 202597,39
100, to read volume in hundreds of cubic feet or cubic meters.
257600 cubic feet. For the 5M through the 38M sizes (Figure 9b), the
NOTE: If the last two digits “83” to the right of the seven digits between the arrows on the nameplate
arrows were included in the reading, the odometer “1592432” are equal to cubic meters.
in Figure 8a would indicate a volume of 257683 NOTE: If the last digit “7” to the right of the
cubic feet. comma were included in the reading, the odometer
For the 16M through the 56M sizes (Figure 8b), the in Figure 9b would indicate a volume of 1592432.7
six exposed digits (38498) between the arrows on cubic meters.
the nameplate are typically multiplied by 100 to read On the 56M metric meter (Figure 9c), all of the
the volume in hundreds of cubic feet or 3849800 odometer digits are between the arrows and are read
cubic feet. as cubic meters. The decimal point (comma) is shown
NOTE: If the last digit “7” to the right of the arrows just before the graduated increments on the test
were included in the reading, the odometer in Figure wheel. A reading of 18074618 is literally 18074618
7a would indicate a volume of 3849870 cubic meters.
cubic feet.
NOTE: Some customers will special order Accessory
Units with a multiplication factor of 1000. Verify that
the marking between the arrows on the Accessory Unit
nameplate for that particular unit indicates the correct
multiplier, (i.e. “Reading X 100 Cu. Ft.” as explained
previously, or “Reading X 1000 Cu. Ft.”)

Figure 9 - Non-Compensated Series 3 Metric Unit

odometers for 8C (9a Top), 16M (9b Middle), and
Figure 8 - Non-Compensated Series 3 Imperial unit 56M (9c Bottom).
odometer for 8C (8a Top) and 16M (8b Bottom).

11
TEST WHEEL METER INSTALLATION
The index wheel numbers on the odometer have 10 Piping Configurations
divisions marked that range from 0 through 9 located
Series B3 and B3-HP meters can be installed in either
on the right side of the odometer. The graduated
a Top Inlet (vertical gas flow) or a Side Inlet (horizontal
increments on the test wheel represent 0.2 cubic feet
gas flow) configuration as shown in Figures 11 and 12
for the 8C through 11M meters and 2 cubic feet for the
respectively. The preferred installation is top inlet in a
16M through 56M meters. This allows for accurately
vertical pipeline with gas flowing downward. Although
estimating readings of 0.1 cubic feet and 1 cubic foot,
the design of the impellers tends to make the meter
respectively. For metric versions, the graduated
self-cleaning, top inlet mounting enhances the ability
increments on the test wheel represent 0,002 cubic
to pass dirt, pipe scale, or other debris through
meters for the 8C through 3M meters, 0,02 cubic
the meter.
meters for the 5M through 38M meters, and 0,2 cubic
meters for the 56M. This allows for accurately Piping should be rigid and properly aligned. The
estimated readings of 0,001 cubic meters, 0,01 cubic meter does not require any direct means of support.
meters, and 0,1 cubic meters respectively. However, the piping might need support to eliminate
any piping strains which may cause the meter to bind.
Whether imperial or metric, the white reflective
marks that are located to the left of the graduated Another recommendation is to install the meter with
increments are used for prover testing with an a bypass adjacent to the main line. Additionally, the
optical photo-sensor (scanner). installation of tees upstream and downstream of the
meter will help facilitate transfer proving or other types
TC ODOMETERS of testing with the meter still mounted in the pipeline.
As shown in Figure 10, the TC unit has two digital
Do not install the meter lower than the discharge pipe
odometers. The top odometer represents the
run to avoid accumulation of condensate or foreign
Temperature Compensated volume corrected to a
materials in the metering chamber. Use a Gasket style,
contract Base temperature of 60° F (or 15° C). This
Y-type, or some other kind of strainer upstream of the
top odometer can be read in a similar fashion to the
meter to help remove foreign matter (pipe sealant,
uncorrected odometers as shown in Figures 8 and 9.
tape, weld slag, etc.) from the gas stream. A 100 Mesh
The bottom odometer is Non-Compensated and is screen is recommended for any strainer used.
typically covered with a translucent mask to reduce
The installation of a lubricated gas valve directly before
readability and/or prevent misreading. An optional
a meter is not recommended, as excess valve lubricant
black mask can be specified to completely prevent
may stop impeller rotation.
viewing of the non-compensated odometer. Other
masking configurations are available upon request. If over-speed conditions could occur, a restricting flow
orifice plate should be installed 2 to 4 pipe diameters
downstream of the meter outlet. Contact the factory or
your Dresser representative for sizing, pricing and
availability.
NOTE: Warranty does not cover meter failure due to
over-speed conditions.

Figure 10 - Temperature compensated Accessory

Units have two odometers for a temperature compen-
sated reading on top and a non-compensated reading
on the bottom.

12
 Strainer
Isolating Valves

Restricting Flow
1/4" Blow-off Orifice Plate
Valve

1/4" Needle
Valve

Inlet Outlet

Figure 11 - Top Inlet Configuration for Series B3 Meter.

Restricting Flow
Strainer Orifice Plate

Isolating
Valves

1/4" Blow-off
Valve

1/4" Needle
Valve
Inlet Outlet

Figure 12 - Side Inlet Configuration for Series B3 Meter.

13
Placing Meter In Line CAUTION: The meter must NOT be under pressure
IMPORTANT: Do not fill meter end cover oil reservoirs for this procedure.
until after the meter has been permanently installed 5. After the meter has been installed, remove the
and is ready for service. (Refer to Figure 14 for oil hex head plug located in the timing gear end
reservoir locations). cover (as shown in Figure 13) by using a Hex
1. Before installing a meter: wrench. Insert an Hex wrench into the gear clamp
• Make sure the upstream piping is clean. During and slowly turn the impellers clockwise, checking
this procedure, use extreme caution and follow for free rotation. If binding is present, do not
recommended company procedures. attempt to disengage the impellers. Remove
• Remove the plastic protective caps from both the meter from the set and clear all obstructions
meter flanges prior to meter installation. or piping strain prior to reinstalling the meter.
• Ensure the impellers turn freely and no objects Reinstall the plug and torque to 6-7 ft-lbs after
or contaminants are in the measuring chamber. verifying free impeller rotation.

2. Meter Orientation: DANGER: Slowly depressurize the meter set before

working on meter.
• Connect meter inlet to the gas supply side
of the line.
• In a correct meter installation, the counter and
gear end oil level gauges are parallel to the
ground.
IMPORTANT: The arrow on the name plate MUST
represent the direction of flow of gas through
Access Plug
the meter
3. Install the meter without piping strain to prevent
binding of the impellers and use the proper pipe
supports if required. Level all meters to within
1/16” per running foot (5 mm/m), side-to-side Figure 13 - Remove the access plug to check
and front-to-back for proper alignment. impeller rotation.
4. Tighten flange bolts evenly in a cross-pattern. 6. A sufficient amount of oil is shipped with each new
The maximum recommended torques are meter to fill the meter body reservoirs in either Top
provided in Table 8. or Side Inlet configuration. Slowly add oil to the
meter reservoirs until the oil level comes up to the
Meter Bolt Torque (ft-lbs) center of the oil gauge (sight glass) as shown in
Size Diameter Lubricated Non-Lubricated Figure 14. Refer to Figure 15 for oil fill/drain plugs
8C175-16M175 5/8” 55 and sight glass locations. DO NOT OVERFILL THE
23M232 5/8” 55 RESERVOIRS.
23M175-56M175 3/4” 80 Not recommended
1M300 3/4” 80 Meter Side Top
3M300 5/8” 80 Size Inlet Inlet
8/11/15C 0.8 OZ. (23,7 ml) 3.0 OZ (88,7 ml)
Table 8 - Recommended Flange Bolt Torques
2/3/5M 1.25 OZ. (37 ml) 7.6 OZ (224,8 ml)
7/11/16M 3.0 OZ. (88,7 ml) 21.85 OZ (646,2 ml)
23/38/56M 40.2 OZ. (1,2 l) 154 OZ (4,55 l)
23M232 - 4” 3.4 OZ. (100,6 ml) 21.8 OZ. (644,7 ml)
1M/3M300 1.25 OZ. (37 ml) 7.6 OZ. (224,8 ml)
Table 9 - Oil Capacities

14
After a meter is installed in line and oil has been added
to the meter reservoirs, gas flow will rotate the meter IMPORTANT: DO NOT add oil to the
impellers. The oil slingers will splash lubricant into permanently lubricated Series 3 Accessory
the bearings. This will quickly reduce any operational Unit. DO NOT drill and tap the Lexan® cover.
friction created by dry bearings.

C C C
L

Figure 14 - Fill oil reservoirs to mid level of sight glass.

Series B3 8C-16M, 23M232

Oil Fill Plugs Oil Fill Plugs

Inlet

Outlet

Oil Sight Gauges Oil Sight Gauges

Series B3 23M-56M (Side Inlet Shown)

Oil Fill/ Drain Plugs

Inlet Inlet

Oil Sight Gauges

Figure 15 - Oil fill/drain plugs and oil level sight gauge locations.

15
Meter Start-Up c) Let the meter operate at low speed for several
IMPORTANT: The maximum working pressure of any minutes. Listen closely for unusual scraping
rotary meter is limited by casing design. Meters should or knocking sounds.
not be installed where line pressure can exceed the d) If operation is satisfactory, go directly to Step f).
Maximum Allowable Operating Pressure (MAOP). e) If unusual sounds are present or the accessory
Refer to the basic meter body nameplate for the MAOP. unit’s RPM wheel is not turning, place the meter
in bypass. Slowly depressurize and vent all
1. Slowly pressurize the meter in accordance with the
pressure from the meter set before checking for
following recommendations:
piping misalignment, piping strain, torsion, or
IMPORTANT: Do not exceed 5 psig/second (35 kPa/ other related problems. (Release pressure at a
second) maximum when pressurizing. Rapid pressur- rate less than 5 psig/second.) Once the problem
ization can cause an over-speed condition which may is resolved, repeat the start-up procedure
damage the meter. Resulting damage is not covered by beginning with step a).
warranty.
a) Open the bypass and outlet (downstream of DANGER: Slowly depressurize and
meter) gas valves. vent all pressure from the meter
b) Partially open the meter inlet gas valve until set before working on meter.
the meter starts operating at low speed.
Throttling the bypass valve may be necessary to
initiate gas flow through the meter. Verify gas is
flowing through the meter by watching for
movement of the black-and white RPM wheel
on the Accessory Unit. The wheel shown in
Figure 16 is visible from either the front or the
side of the Lexan® cover. If movement is present,
go to Step c). If the RPM dial is not turning, f) Gradually open the inlet valve until a full flow
verify gas is being delivered to the meter. If gas is passing through the meter and the inlet
is flowing to the meter inlet and the RPM wheel valve is fully open.
is not moving, go to Step e). g) Slowly close the bypass valve.
h) Follow your company’s authorized procedures or
common industry practices to leak test the meter
and all pipe connections. Soapy water, Snoop®
or gas analyzers are commonly used for this
procedure.

INSPECTION AND MAINTENANCE

Maintenance for the Series 3 Accessory
IMPORTANT: NO oil is required for the Series 3
accessory unit.
The CTR, CD, ICEX, TC, TD and Solid State Pulser do
not require scheduled maintenance.
To clean the Lexan® cover, use hot water and soap,
mineral spirits, Isopropyl alcohol, or cleaning products
approved for use on Lexan®.
Figure 16 - Movement of the RPM wheel indicates
IMPORTANT: Aromatics, Ketones, and Chlorinated
impeller rotation.
hydrocarbons will damage the Lexan® cover. Do not
use acetone, carbon tetrachloride, etc.

16
Meter Lubrication ACCESSORY UNIT REMOVAL &
Use only ROOTS® Meter Oil or other instrument grade CONVERSION PROCEDURES
oils approved for service by the manufacturer. The following section covers general procedures for
changing complete accessory units as well as config-
Meters installed and maintained in accordance with
uring the Series 3 Instrument Drive. For detailed
factory recommendations can be expected to operate
instructions of these procedures, refer to the docu-
dependably for many years. Proper oil level and
mentation cited at the end of each section. These gen-
cleanliness have the greatest effect on meter’s life
eral procedures require the following tools and equipment:
expectancy. Visually inspect the two oil reservoirs in
the meter end covers for proper mid-gauge oil levels • 5/32” Allen wrench
once a month until a practical interval is determined. • 9/64” Allen wrench
Add oil as necessary. • A light grade of machine oil, grease or
Oil change frequency will depend upon the cleanliness petroleum jelly for lubricating o-rings.
of the gas being measured. Change oil when the color • Adjustable torque wrench with a range of
darkens or when the level changes. Under favorable 5-40 in-lbs.
conditions, these periods may be from 3 to 5 years, Removing the Accessory Unit from the Meter
or longer. (Refer to Figure 17)
CAUTION: THE METER END COVER Use the 5/32” Allen wrench to remove the four #10-24
IS PRESSURIZED. screws holding the slip flange on the meter end cover.
Bleed off the line pressure before Loosen the screws in a cross or star-like pattern.
removing the oil fill or drain plugs
Remove the accessory unit by carefully pulling the
from the meter.
complete assembly directly away from the meter body,
DO NOT add oil to the Series 3 Accessory Unit. taking care not to damage the male driving magnet on
the accessory gear train. IMPORTANT: If the accessory
Meter Level unit is temperature compensating, slide the assembly
directly away from the meter end cover until the
Since the meter is supported entirely by the gas pipe temperature probe has cleared the end of the meter.
line, movement of the piping due to accidents, settling Make sure the thermocouple (bi-metallic probe) does
of the ground or other causes may impede meter not bind in the probe well during the removal process.
operation and accuracy. Refer to “INSTALLATION” Shock and/or damage may result in a loss of
procedures. Make sure the meter remains level within compensating accuracy.
1/16” per foot (5 mm/m) in any direction, side-to-side
and front-to-back. Remove the O-ring from the meter end cover, if
applicable. Verify which type of o-ring seal is being
Cleaning and Flushing used on the accessory unit before replacing.
NOTE: Before removing meter from the pipeline or
NOTE: The newer Lexan® cover will have the
performing this procedure, drain all oil from the
quad-seal O-ring installed in the Lexan® Cover.
meter end covers. Add oil after the meter has been
If the quad o-ring comes loose from the groove in
replaced in the meter set.
the Lexan® cover, clean the cover and O-ring with
After removing the meter from the line, if there is any alcohol before attempting to replace the O-ring
evidence of dirt or dust in the meter, a suggested
For detailed information on removing/installing the
method for cleaning is to windmill the impellers (at a
accessory unit, request document 055679-000 and
speed less than maximum capacity) by injecting low
053938-000.
pressure, dry compressed air from a nozzle into the
meter inlet. Flush approximately 5 ounces (150 ml) of Removing the Gear Reduction Assembly from the
an approved non-toxic, non-flammable solvent through Lexan® Cover (Refer to Figure 18)
the meter. Drain any residual cleaning fluid from the Use a 9/64” Allen wrench to remove the mounting
meter body and end covers. Use compressed air to screw holding the accessory unit in the Lexan® cover.
completely dry the meter. The screw can be accessed through the Tool Access
Port as shown in Figure 18.
Slide the gear reduction unit out of the Lexan® cover.
17
 Gas Flow

Quad Seal
Temperature Probe
(TC Only)
Meter End Cover
Lexan Cover
Slip Flange

Magnet Cup

Odometer(s)
Facing Outward
Male Driving Magnet
#10-24 Screws (4x)

Figure 17 - Assembling Series 3 Accessory to meter end cover.

Figure 18 - Exploded view of Gear Reduction Assembly and Lexan® Cover.

18
Replacing the Gear Reduction Unit in Lexan Cover Instrument Drive Conversion (Side Inlet to Top Inlet
(Refer to Figure 18) Conversion)
1. Slide the gear reduction unit into the Lexan® The following procedures are required to change the
cover. Align the odometer(s) with the large, position of the instrument drive assembly and drive
clear portion of the cover. When the gear dog rotation direction. Refer to Figures 19, 20 and 21
reduction unit is properly installed, the pin that is for component locations.
molded into the bottom of the Lexan® cover will
engage a hole in the top plate of the accessory. NOTE: Regardless of Side Inlet or Top Inlet meter
2. Using a 9/64” Hex wrench, insert the screw installation, the Instrument Drive Mounted device
into the threaded boss on the Lexan® cover and must always be installed in a vertical position during
torque to 20-25 in.-lb. Do not over tighten to operation. Refer to the “METER INSTALLATION -
avoid damage to the threaded boss. Piping Configurations” section of this manual for
proper meter mounting practices.
For detailed information on Installing/Replacing
the Gear Reduction Unit in Lexan® Cover, request 1. Use a flat blade screwdriver to remove the two
document #055679-000. 1/4-20 screws holding the Universal Instrument
Adapter Plate to the ID support assembly.
Installing a Complete Accessory Unit on the Meter
(Refer to Figure 17) 2. Using the 5/32” Allen wrench, remove the four
#10-24 screws holding the neck of the ID
1. Ensure the Quad Seal O-ring is fully seated into Support Assembly to the aluminum ID Housing.
the cover. 3. Using a 5/32” Allen wrench, remove the two
2. Align the male driving magnet with the magnet #10-24 screws holding the Side Cover Plate onto
cup in the meter body. If the Accessory Unit is the aluminum ID housing. Remove the cover
temperature compensated, align the temperature plate.
probe with the probe well. Carefully slide the 4. Install the ID support assembly in the vertical
probe into the meter end cover probe well until mounting position (where the cover plate was
the Lexan® cover meets the meter body. removed). Torque the screws to 37-40 in.-lb.
NOTE: The foam attached to the temperature probe 5. Re-install the Side Cover Plate to the position
should not be removed. The foam is installed to from where the ID Support was removed.
prevent the ambient temperature inside the Lexan® Torque the screws to 5-7 in.-lb.
housing from entering the probe well and affecting the 6. Using a 5/32” Allen wrench, remove the two
temperature probe readings. #10-24 screws holding the Front Cover Plate
3. While holding the Accessory Unit in place, slide onto the aluminum ID housing. Remove the
the slip flange over the Lexan® cover. Rotate the cover plate.
slip flange until all four holes in the slip flange 7. Using a 5/32” Allen wrench, remove the two
are aligned with the four screw holes in the meter #10-24 screws holding the Bevel Gear Train
end cover. This should place the dimple in the Assembly in place. Make sure the O-ring behind
slip flanges in alignment with the odometer(s) the Bevel Gear Train Assembly remains attached
(non-instrument drive version only). to the back of the assembly. Do not allow any
4. While holding the slip flange to the meter’s end thing to contaminate the O-ring.
cover, insert the four #10-24 screws into position 8. Making sure the O-ring remains in place,
and tighten in a cross or star-like pattern to re-install the Bevel Gear Train Assembly in the
6-9 ft.-lb. When properly installed, the slip vertical position. Torque these screws to
flange will be in continuous contact with the 5-7 in.-lb.
meter end cover. 9. Ensure the rotation is set as desired and the
5. If applicable, follow your company procedures Bevel Gear Train Assembly engages properly
for installing security devices. with the ID drive shaft. Windmill the meter to
For detailed information on installing a Complete verify proper rotation of the Drive Dog.
Accessory Unit on the Meter, request document 10. Install the Front Cover and torque these screws
#055679-000. to 5-7 in.-lb.

19
 #10-24 Screws (2x)

ID Support Assembly

ID Support Mounting Location

(Vertical Flow) ID Housing

O-Ring
Side Cover Plate
Modular Bevel Gear

20
Train Assembly
#10-24 Screws (2x)
Front Cover Plate

ID Support Mounting Location

(Horizontal Flow)

#10-24 Screws (2x)

#10-24 Screws (2x)

Figure 19 - Exploded View of Instrument Drive (ID) Assembly.

 1/4-20 Screws (2x) Gas Flow

Universal Instrument
Adaptor Plate Quad Seal Meter End Cover

Drive Dog

Lexan Cover and

Gear Reduction unit
Quad Seal

Drive Dog Shear Pin

Figure 20 - Assembly Instrument Drive to meter end cover.

Bevel Gear
on Top

Bevel Gear
on Bottom

Bevel Gear Position:

TOP BOTTOM
CD Meters CD Meters
Counter-clockwise (A) Rotation Clockwise (B) Rotation

TD Meters TD Meters
Clockwise (B) Rotation Counter-clockwise (A) Rotation

Figure 21 - Placement of bevel gears determines rotational direction.

21
 11. If applicable, follow your company procedures Installing a Solid State Pulser on a CTR or TC Meter
for installing tamper-evident security devices.
1. Remove CTR or TC Accessory from the meter.
12. Install the Instrument Drive Adapter Plate onto To do this, remove the four screws securing the
the ID Support Housing. slip flange, and remove the slip flange. Gently pull
For detailed information on Instrument Drive Side Inlet the accessory housing assembly off the meter.
to Top Inlet Conversion, request document B054082-091. Remove the screws and slip ring. Then, remove the
Changing the Rotational Direction of the CTR or TC accessory from its housing by loosening
Instrument Drive the screw inside the housing. As shown in Figure 18.
All meters with an instrument drive are shipped from 2. Install Magnet and associated parts that are
the Factory with the “drive dog” rotating in a Clockwise supplied with this conversion assembly.
direction (CW-B) unless otherwise specified at time of 3. Installation of the gear train back into the
order. To change to Counter-clockwise rotation housing is the reverse of removal done at Step 1
(CCW-A), use the following procedure: above. To re-install completed pulser assembly
1. Using a 5/32” Allen wrench, remove the two on meter see: INSTALLING A COMPLETE
#10-24 screws that hold the Front Cover Plate ACCESSORY UNIT ON THE METER above.
onto the aluminum ID housing. Remove the NOTE: For detailed information on the Installation of
cover plate. Refer to Figure 19 for component Solid State Pulsers, request documents 057162-000
identification. and 054190-090.
2. Remove the two #10-24 screws holding the
Modular Bevel Gear Train Assembly in place. Installing a Counter with Electronic Transmitter
Make sure the O-ring behind the modular (ICEX) to a CTR Accessory
assembly remains attached to the back of the 1. Remove the CTR Accessory from the meter.
modular assembly. Do not allow sand, dirt, or To do this, remove the four screws securing the
other debris to contaminate the O-ring. slip flange and remove the slip flange. Gently
3. Rotate the modular drive assembly 180° to pull the accessory housing assembly off the
obtain the proper Drive Dog rotation (refer to meter. Remove the screws and slip flange. Then,
Figure 21). Making sure the O-ring behind remove the CTR accessory from its housing by
modular assembly remains in place; re-install the loosening the screw inside the housing. See
modular gear assembly in the vertical position. Figure 18.
Torque the screws to 5-7 in.-lb. 2. Install Magnet and associated parts that are
4. Ensure the rotation is set as desired and the supplied with this conversion assembly.
modular gear assembly engages properly with 3. Installation of the gear train back into the
the ID drive shaft. Windmill the meter or rotate housing is the reverse of removal done at Step 1
the modular assembly to ensure proper rotation above. To re-install completed pulser assembly
of the Drive Dog. on meter see: INSTALLING A COMPLETE
5. Re-install the Front Cover and torque the ACCESSORY UNIT ON THE METER above.
screws to 5-7 in.-lb. NOTE: For detailed information on the Installation of
6. If applicable, follow your company procedures for the ICEX, request document #056098-100.
installing tamper-evident security devices.
For detailed information on Changing the Rotational
Direction of the Drive Dog, request documents
B054082-091.

22
Installing an AMR Adapter TESTING
1. The CTR or TC must be removed from the meter. General
To do this remove the four screws that attach the Rotary meters are tested for accuracy by several
Accessory Unit to the meter. Slide the Slip industry accepted methods. These test methods
Flange off the Accessory Unit. include, but are not limited to transfer, bell, piston,
2. Gently pull the Accessory Unit straight back away sonic nozzle, and critical flow proving. The Differential
from the meter. Special care should be taken Test is unique to rotary meters and is a convenient
when removing a TC unit of any kind so as not to method of comparing a meter’s performance to
bend or damage the temperature probe. previous or original performance records. Differential
testing is accepted by many State Utility Commissions
3. Remove the CTR or TC from the housing by as a means of periodically verifying that the original
loosening the screw inside the Lexan Accessory accuracy of a meter has remained unchanged.
Housing. Slide the CTR/TC Assembly out of the
Housing. Set aside this Accessory Housing, as a Differential Test
new AMR Adapter Housing will replace it.
Only a change in the internal resistance of a meter can
4. Place the Slip Flange over the New AMR affect its accuracy. Any increase in the resistance to
Adapter Accessory Housing. flow will increase the pressure drop between the inlet
and outlet of the meter, thus increasing the differential
5. Verify that the AMR adapter plate is oriented in
pressure drop. This is why the meter differential
the correct position to ensure the AMR device is
pressure drop appears as a prime indicator of
upright. AMR vent holes should always be facing
meter condition.
the ground. Using the hex wrench, install the
four #10-24 socket head cap screws to assemble Although accuracy cannot be directly determined by
the AMR Adapter plate to the AMR Adapter a differential test, it has been shown that an increase
Accessory Housing. Tighten the four screws of up to 50 percent in the differential pressure, at the
to 8-10 in-lb. higher flow rates (25% and above), can be tolerated
without affecting meter accuracy by more than 1
6. Carefully slide the CTR/TC Assembly into the
percent. Supportive technical data is available
Housing. CAUTION: Make sure the output Drive
upon request.
Shaft of the Counter/TC unit aligns and inserts
into the Coupling in the AMR Adapter Accessory Usually flushing a meter will eliminate a high
Housing by ensuring the paddle on coupling differential caused by minor contamination. Refer to
aligns with slot on 72 tooth gear. “INSPECTION AND MAINTENANCE, Cleaning and
Flushing” sections for cleaning instructions.
7. Install the Slip Flange onto the meter cover, with
countersunk side facing the meter. Tighten the
screws in a star-like pattern and torque to 45 psig

47-53 in-lb.
30 psig
Meter Differential Pressure

8. Press fit the appropriate Drive Dog onto the

Increasing

customer supplied AMR and install assembled

AMR onto AMR adapter plate. 15 psig

NOTE: For detailed information on the FIELD Atmospheric

INSTALLATION of AMR adapters, request documents
0 25 50 75 100
057862-000 or 058779-000.
Meter Capacity %

Figure 22 - Differential Curves change as

pressure increases.

23
Establishing Baseline Curves
Developing an original differential baseline curve is Figure 23 will allow the technician to compare new
recommended when the meter is first installed. Since test data to older data.
any change in flow rate, line pressure or specific
A test under actual operating conditions will provide
gravity will cause a change in the differential, at least
the most reliable data for future checks of a meter’s
three (3) test points are required at gas flow rates
operating condition. This is particularly important
from 25%to 100% of meter capacity. (As shown in
when the line pressure is higher than 15 PSIG (200
Figure 22, the resulting points will be non-linear, so a
kPa Absolute). Since meter differential pressure
minimum of three points is necessary to establish a
increases with line pressure, multiple curves may
curve.) Plot the points on a graph and then connect
be necessary for meters under varying line pressure
the points to form a curve. This provides an accurate
conditions.
baseline for comparison to later tests. To help with
record keeping, a data chart like the one shown in

Differential - Rate Test Data - SAMPLE SHEET

Meter Model: Mfg. Serial No: Utility Serial No.:
Location: Date Installed: Register Reading:
Line Gas Specific Volume Run Rate Differential Pressure Date Tester
Pressure Temp Gravity Measured Time (ft3) In. W.C. % Change
Initial Tests - New Meter

Periodic Check Tests

Figure 23 - Having a single data chart for each meter provides a detailed history of differential rate tests
for future use.

24
Differential Test Procedure
Testing requires differential pressure test equipment
with an indicating scale range of at least 50 inches of
water column. The testing device should have bypass ∆P
valving and must be pressure rated for the maximum
metering line pressure for the test. Pressure lines
8C - 16M B3
should be connected to the 1/4” meter inlet and outlet
pressure taps located on the meter body as shown in 1M/3M B3-HP
Figure 24. For meters with Maximum pressure ratings
of 300 psig (2068 kPa) or less, Pete’s Plugs® can be
permanently installed in the pressure taps to facilitate
testing.
∆P
A pressure gauge is used to verify pressure readings.
A stop watch is used to “clock” the meter RPM for

23M - 56M B3
calculating gas flow rate.
Pete’s Plugs® is a registered trademark of Peterson Equipment Company.
Figure 24 - Differential pressure taps are located
CAUTION: When the meter is pressurized, follow above and below the meter nameplate.
applicable safety rules and use appropriate personal
protective equipment. 4. Record the pressure differential, line pressure,
and gas specific gravity. Repeat the test to
1. Install the pressure differential test equipment
obtain an accurate average reading.
into the meter inlet and outlet differential taps.
Follow the manufacturer’s instructions for proper NOTE: At the time of meter start-up in a new installa-
installation and operating procedures. On the tion, repeat Steps 2 - 4 at a minimum of three different
upstream side of the meter, install a pressure flow rates, each between 25% and 100% of meter
gauge or other pressure standard if not already capacity. An original baseline curve should be drawn
a part of the test equipment. using data at a constant pressure for all three tests.
2. Adjust the meter bypass and the meter inlet 5. Remove the differential test equipment and
valves until the meter is operating at a predeter- pressure standard.
mined or selected flow rate in the lower capacity
6. If this is for the baseline curve, plot and save the
range or no less than 25 percent of the meter’s
curve for future reference. If this is a subsequent
rated capacity. Let the flow rate stabilize.
test and the pressure differential compares
3. Time or “clock” the passage of a predetermined against the baseline curve within acceptable
volume of gas registered on the instrument to limits, return the meter to full service. If the
determine the Flow Rate in Actual Cubic Feet per pressure differential is not within acceptable
Hour (or m3/h): limits or has increased by 50% above the values
on the baseline curve, remove the meter for
Index Rate = (Test Volume in CF) x (3600) inspection and if needed, for service.
(Test Time in Seconds)
After developing a baseline curve, meter condition and
Convert the calculated flow rate to a percentage of meter performance can be checked periodically by running a
rated capacity: similar differential rate test at a single selected point.
% Meter Capacity = ( MeterIndex Rate
Base Rating
) x 100 If the differential pressure increases by more than
50 percent above the original value, then inspect the
meter for causes for resistance. The usual causes are
NOTE: The base rating for a meter can be found on the
binding impellers, worn bearings, contaminates such
nameplate located on the body of the meter. The rating
as dirt or valve grease in the metering chamber, and
is designated in both “CFH Max” and “m3/h Max”.
wrong viscosity oil or excess oil. Refer to “INSPEC-
TION AND MAINTENANCE, Cleaning and Flushing”
for cleaning instructions.

25
For Factory repairs and/or inspection, please call your TC Unit Operational Check
Customer Service Representative or your ROOTS®
This procedure may be used to verify the accuracy of
meter supplier to request a Return Material
the TC Unit independent of the meter body accuracy.
Authorization (RMA).
The design accuracy for the TC Unit is ± 0.5% for
Proving Operations gas temperatures between -20°F to +120°F (-29°C
and +49°C).
The accuracy of a ROOTS® meter is easily verified
using standard transfer proving techniques. A Model 5 NOTE: All Series B3 ROOTS TC meters are compensat-
ROOTS® Prover allows for almost hands free testing ed to a 60° F (or 15° C) Base Temperature.
and offers four different methods for starting and The TC Unit Operational Check is based upon
stopping the test. The first two methods, which utilize Measurement Counts (actual measurement) versus
original equipment included with the Model 5 Provers, Theoretical Counts, using a 25 cycle count of the
are performed using the Manual Start/Stop Switch or compensation cycle. This is the best method for deter-
the field meter Instrument Drive Pulser. mining the accuracy of the TC unit with the meter in
With the manual Start/Stop switch, the operator will service. By using the 25 cycle method, all of the gears
input the desired volume into the Model 5 program. in the TC unit make a complete revolution, and thus
After the flow and temperature have stabilized, the provides a greater amount of confidence in the result-
operator will use the switch to start the test. After the ing accuracy calculation. The method for determining
field meter odometer has reached the desired volume, the theoretical counts for a 25 cycle test is outlined in
the operator will again push the switch to stop the test. the “Calculating Theoretical Counts” section.
For noncompensated meters with an Instrument Drive, A ROOTS® Transfer Prover can be used for a TC Unit
the field meter Instrument Drive Pulser mounts Operational Check in the shop or when the meter is
directly to the instrument drive and provides a more not in service. The prover is used for flow rate control
accurate automated test. The desired volume is selected and temperature indication during the test procedure.
and the prover will automatically start the test after The prover may also be used to test the meter body
conditions have stabilized. The test will then stop at accuracy using the non-compensated odometer or the
the desired test volume. RPM test wheel (See: “Proving Operations,” in the
previous section.) Then the information derived from
Optional equipment for the Model 5 prover can include the TC Unit Operational Check can be combined with
the RS-Scanner. Like the Instrument Drive Pulser, the meter’s non-compensated accuracy to determine
the Scanner can also automate control of the test. the meter’s overall accuracy using this formula:
The Scanner can be used to test both Temperature
Compensated (TC) and Non-Compensated meters. (meter accuracy * TC accuracy) = overall or combined
This system uses a light beam to focus and trigger on 100 accuracy
the white squares of the odometer or the high speed
dial at the end of the ROOTS Meter Accessory Unit. NOTE: TC Calibration is not covered in this manual
The dial will rotate from white to black (and vice versa) other than to state that during the calibration proce-
triggering a pulse relating to a specific volume. dure the TC probe should be immersed into a tightly
controlled temperature bath set at the accessory unit’s
NOTE: On Series 3 version ROOTS Meters, the high
base temperature. Calibration of the TC Unit should not
speed wheel attached to the end of the RPM drive
be performed while the accessory is installed on the
shaft is visible either from the front or the end of the
meter or with the temperature probe exposed to the
accessory and can be used for meter testing. The
atmosphere (air).
wheel is shown in Figure 16 in the “Meter Start-Up”
section under Meter Installation.

26
Procedure for the TC Unit Operational Check 5. Use Table 10 or the formula described in
1. Measure and record stabilized gas (or air) “Calculating Theoretical Counts” below to
temperature directly at the meter inlet using a determine the “Theoretical Number of Counts”
certified temperature standard. (TNC) for the indicated temperature recorded in
Step 1.
NOTE: Inaccurate results may occur if the gas
temperature has not stabilized before starting the test. 6. Calculate the percent accuracy of the TC Unit by
using the following equation:
2. Record the temperature displayed by the
Accessory Unit’s temperature probe. The indicated Percent Accuracy = (Cf – Ci) x 100
temperature is visible through the accessory TNC
housing window located above the odometers. Example: Assume the gas temperature is 53.0°F,
Compare to the readings taken in Step 1. Both and from Figure 25, the initial odometer reading
values should agree within ± 4 °F. (Ci) = 9756. We then allow the odometer to cycle
NOTE: The temperature indicated by the unit’s temper- 25 times and record the final reading. We will further
ature probe will not be used for calculation since this assume the final odometer reading (Cf) = 2295.
is an estimated reading. Use the temperature recorded NOTE: When Cf is less than Ci, place a “1” in front
in Step 1 as the reference temperature for the TC unit of the reading for Cf. In this example, the adjusted
operational check. reading for Cf would read as “12295”.
3. Observe the Temperature Compensated volume From Table 10, the Theoretical Number of Counts
odometer. When the odometer stops turning (TNC) = 2534.1.
after an intermittent compensating cycle, record
the last 3-digit reading and the value indicated by Using these numbers in the “Percent Accuracy”
the graduated marks on the test wheel as the formula, the accuracy is calculated as:
“Counts, Initial” (Ci) indicated on the odometer. (12295 – 9756) x 100 = 100.19%
This is read as a whole number. (Refer to the 2534.1
Sample Counter Reading in Figure 25.)
NOTE: Some of these digits may be partially or Calculating Theoretical Counts
completely obscured by masking. The masking must The number of theoretical counts (TNC) can be
be removed if the readings are not visible. calculated for Fahrenheit as shown:

(TNC) = (460 + TB) x (Number of Cycles x 100)

(460 + TA)
Where TB = Base Temperature (Typically 60°F or 15C)
TA = Actual Gas Temperature
The number of theoretical counts (TNC) can be
calculated for Celsius as shown:

(TNC) = (273.15 + TB) x (Number of Cycles x 100)

(273.15 + TA)

Figure 25 - A reading of 9756 would be the number Example: For a 25 cycle test, the Theoretical Number
recorded for TC unit operational check. of Counts (TNC) for gas temperature of 70.0°F and a
60° F base temperature is calculated as follows:
4. After the Compensated Volume odometer has
cycled 25 times and stopped, record the last = (460 + 60) x (25 x 100)
3-digit reading and the value indicated by the (460 + 70.0)
graduated marks on the test wheel as the 1,300,000
“Counts, Final” (Cf), exactly as described in = = 2452.8
530.0
Step 3 above.

27
Table 10 - Temperature Cycle Testing -Theoretical Number of Counts (TNC) for specified temperature in degrees
Fahrenheit (°F). Based on 25 Temperature Compensation Cycles.
°F TNC °F TNC °F TNC °F TNC °F TNC °F TNC
50.0 2549.0 55.0 2524.3 60.0 2500.0 65.0 2476.2 70.0 2452.8 75.0 2429.9
50.1 2548.5 55.1 2523.8 60.1 2499.5 65.1 2475.7 70.1 2452.4 75.1 2429.5
50.2 2548.0 55.2 2523.3 60.2 2499.0 65.2 2475.2 70.2 2451.9 75.2 2429.0
50.3 2547.5 55.3 2522.8 60.3 2498.6 65.3 2474.8 70.3 2451.4 75.3 2428.5
50.4 2547.0 55.4 2522.3 60.4 2498.1 65.4 2474.3 70.4 2451.0 75.4 2428.1
50.5 2546.5 55.5 2521.8 60.5 2497.6 65.5 2473.8 70.5 2450.5 75.5 2427.6
50.6 2546.0 55.6 2521.3 60.6 2497.1 65.6 2473.4 70.6 2450.1 75.6 2427.2
50.7 2545.5 55.7 2520.8 60.7 2496.6 65.7 2472.9 70.7 2449.6 75.7 2426.7
50.8 2545.0 55.8 2520.4 60.8 2496.2 65.8 2472.4 70.8 2449.1 75.8 2426.3
50.9 2544.5 55.9 2519.9 60.9 2495.7 65.9 2472.0 70.9 2448.7 75.9 2425.8
51.0 2544.0 56.0 2519.4 61.0 2495.2 66.0 2471.5 71.0 2448.2 76.0 2425.4
51.1 2543.5 56.1 2518.9 61.1 2494.7 66.1 2471.0 71.1 2447.7 76.1 2424.9
51.2 2543.0 56.2 2518.4 61.2 2494.2 66.2 2470.5 71.2 2447.3 76.2 2424.5
51.3 2542.5 56.3 2517.9 61.3 2493.8 66.3 2470.1 71.3 2446.8 76.3 2424.0
51.4 2542.0 56.4 2517.4 61.4 2493.3 66.4 2469.6 71.4 2446.4 76.4 2423.6
51.5 2541.5 56.5 2516.9 61.5 2492.8 66.5 2469.1 71.5 2445.9 76.5 2423.1
51.6 2541.0 56.6 2516.5 61.6 2492.3 66.6 2468.7 71.6 2445.4 76.6 2422.7
51.7 2540.6 56.7 2516.0 61.7 2491.9 66.7 2468.2 71.7 2445.0 76.7 2422.2
51.8 2540.1 56.8 2515.5 61.8 2491.4 66.8 2467.7 71.8 2444.5 76.8 2421.8
51.9 2539.6 56.9 2515.0 61.9 2490.9 66.9 2467.3 71.9 2444.1 76.9 2421.3
52.0 2539.1 57.0 2514.5 62.0 2490.4 67.0 2466.8 72.0 2443.6 77.0 2420.9
52.1 2538.6 57.1 2514.0 62.1 2489.9 67.1 2466.3 72.1 2443.1 77.1 2420.4
52.2 2538.1 57.2 2513.5 62.2 2489.5 67.2 2465.9 72.2 2442.7 77.2 2420.0
52.3 2537.6 57.3 2513.0 62.3 2489.0 67.3 2465.4 72.3 2442.2 77.3 2419.5
52.4 2537.1 57.4 2512.6 62.4 2488.5 67.4 2464.9 72.4 2441.8 77.4 2419.1
52.5 2536.6 57.5 2512.1 62.5 2488.0 67.5 2464.5 72.5 2441.3 77.5 2418.6
52.6 2536.1 57.6 2511.6 62.6 2487.6 67.6 2464.0 72.6 2440.9 77.6 2418.2
52.7 2535.6 57.7 2511.1 62.7 2487.1 67.7 2463.5 72.7 2440.4 77.7 2417.7
52.8 2535.1 57.8 2510.6 62.8 2486.6 67.8 2463.1 72.8 2439.9 77.8 2417.3
52.9 2534.6 57.9 2510.1 62.9 2486.1 67.9 2462.6 72.9 2439.5 77.9 2416.8
53.0 2534.1 58.0 2509.7 63.0 2485.7 68.0 2462.1 73.0 2439.0 78.0 2416.4
53.1 2533.6 58.1 2509.2 63.1 2485.2 68.1 2461.7 73.1 2438.6 78.1 2415.9
53.2 2533.1 58.2 2508.7 63.2 2484.7 68.2 2461.2 73.2 2438.1 78.2 2415.5
53.3 2532.6 58.3 2508.2 63.3 2484.2 68.3 2460.7 73.3 2437.7 78.3 2415.0
53.4 2532.1 58.4 2507.7 63.4 2483.8 68.4 2460.3 73.4 2437.2 78.4 2414.6
53.5 2531.6 58.5 2507.2 63.5 2483.3 68.5 2459.8 73.5 2436.7 78.5 2414.1
53.6 2531.2 58.6 2506.7 63.6 2482.8 68.6 2459.3 73.6 2436.3 78.6 2413.7
53.7 2530.7 58.7 2506.3 63.7 2482.3 68.7 2458.9 73.7 2435.8 78.7 2413.2
53.8 2530.2 58.8 2505.8 63.8 2481.9 68.8 2458.4 73.8 2435.4 78.8 2412.8
53.9 2529.7 58.9 2505.3 63.9 2481.4 68.9 2457.9 73.9 2434.9 78.9 2412.3
54.0 2529.2 59.0 2504.8 64.0 2480.9 69.0 2457.5 74.0 2434.5 79.0 2411.9
54.1 2528.7 59.1 2504.3 64.1 2480.4 69.1 2457.0 74.1 2434.0 79.1 2411.4
54.2 2528.2 59.2 2503.9 64.2 2480.0 69.2 2456.5 74.2 2433.5 79.2 2411.0
54.3 2527.7 59.3 2503.4 64.3 2479.5 69.3 2456.1 74.3 2433.1 79.3 2410.5
54.4 2527.2 59.4 2502.9 64.4 2479.0 69.4 2455.6 74.4 2432.6 79.4 2410.1
54.5 2526.7 59.5 2502.4 64.5 2478.6 69.5 2455.1 74.5 2432.2 79.5 2409.6
54.6 2526.2 59.6 2501.9 64.6 2478.1 69.6 2454.7 74.6 2431.7 79.6 2409.2
54.7 2525.7 59.7 2501.4 64.7 2477.6 69.7 2454.2 74.7 2431.3 79.7 2408.7
54.8 2525.3 59.8 2501.0 64.8 2477.1 69.8 2453.8 74.8 2430.8 79.8 2408.3
54.9 2524.8 59.9 2500.5 64.9 2476.7 69.9 2453.3 74.9 2430.4 79.9 2407.9
28
TROUBLE SHOOTING CHECKLIST
Trouble Item Possible Cause Remedy
No Flow Registered 1 Obstruction in piping or meter. Check piping and valves to assure an open flow path.
Check for impeller rotation. Refer to Step #5 in the
“Placing Meter in Line” section of this manual (page 14).
Check for free rotation.

2 Index or RPM wheel No gas flow. Open valve or remove obstruction per Item #1.
does not turn.

Low Volume Registration 3 Meter oversized for load. Use proper meter size.
4 Leak at meter bypass. Check bypass and valves.
5 Meter internal friction. See High Differential, Item #6.

High Differential 6 Build-up of deposits Flush meter with approved solvent.

in measuring chamber.
7 Worn bearings or gears. Replace or Return to Dresser’s Product Services Department.
8 High oil level or heavy oil. Check oil level and cleanliness.
Perform differential test.
9 Impellers rubbing Rotate impellers manually to check for binding or rubbing.
cylinder or headplates, Refer to the section Placing meter in line.
or meter out of time. Remove obstructions and/or time the meter.
Verify that the meter is level.
Vibration/Noise 10 Oil leaking in pipe Make sure the meter is properly installed
Refer to Figure 11 & 12
11 Piping misalignment Remove piping strain. Level the meter.
or strain.
12 Impellers rubbing casing. See items #7 & #9.
13 Contaminants in See item #6.
measuring chamber.

29
Imperial Sizing Charts

LINE MOUNTED Foot Mount

MODEL 8C175* 11C175* 15C175* 2M175* 3M175* 5M175* 7M175 11M175 16M175 23M175 23M232 38M175 56M175 102M125
*Also available in 200 PSIG Rating
RATING 800 1100 1500 2000 3000 5000 7000 11000 16000 23000 23000 38000 56000 102000
PSIG Corrected Capacity at Metering Pressure – in MSCFH
1 0.84 1.15 1.57 2.09 3.1 5.2 7.3 11.5 16.7 24.0 24.0 39.7 58.5 106.6
3 0.95 1.30 1.77 2.36 3.5 5.9 8.3 13.0 18.9 27.2 27.2 44.9 66.2 120.5
5 1.05 1.45 1.98 2.63 4.0 6.6 9.2 14.5 21.1 30.3 30.3 50.0 73.8 134.3
10 1.33 1.82 2.48 3.31 5.0 8.3 11.6 18.2 26.5 38.1 38.1 62.9 92.8 168.9
15 1.60 2.20 2.99 3.99 6.0 10.0 14.0 22.0 31.9 45.9 45.9 75.8 111.8 203.6
20 1.87 2.57 3.50 4.67 7.0 11.7 16.3 25.7 37.4 53.7 53.7 88.7 130.8 238.2
25 2.14 2.94 4.01 5.35 8.0 13.4 18.7 29.4 42.8 61.5 61.5 101.6 149.8 272.9
30 2.41 3.32 4.52 6.03 9.0 15.1 21.1 33.2 48.2 69.3 69.3 114.5 168.8 307.4
40 2.95 4.06 5.54 7.39 11.1 18.5 25.9 40.6 59.1 84.9 84.9 140.3 206.8 376.7
50 3.50 4.81 6.56 8.74 13.1 21.9 30.6 48.1 70.0 100.6 100.6 166.1 244.8 445.9
60 4.04 5.56 7.58 10.10 15.2 25.3 35.4 55.6 80.8 116.2 116.2 191.9 282.9 515.2
70 4.58 6.30 8.59 11.46 17.2 28.6 40.1 63.0 91.7 131.8 131.8 217.7 320.9 584.5
80 5.13 7.05 9.61 12.82 19.2 32.0 44.9 70.5 102.5 147.4 147.4 243.5 358.9 653.7
90 5.67 7.80 10.63 14.18 21.3 35.4 49.6 78.0 113.4 163.0 163.0 269.3 396.9 723.0
100 6.21 8.54 11.65 15.53 23.3 38.8 54.4 85.4 124.3 178.6 178.6 295.1 434.9 792.1
110 6.76 9.29 12.67 16.89 25.3 42.2 59.1 92.9 135.1 194.2 194.2 320.9 472.9 861.4
120 7.30 10.04 13.69 18.25 27.4 45.6 63.9 100.4 146.0 209.9 209.9 346.7 511.0 930.6
125 7.57 10.41 14.20 18.93 28.4 47.3 66.2 104.1 151.4 217.7 217.7 359.6 530.0 965.3
135 8.11 11.16 15.21 20.29 30.4 50.7 71.0 111.6 162.3 233.3 233.3 385.4 568.0
150 8.93 12.28 16.74 22.32 33.5 55.8 78.1 122.8 178.6 256.7 256.7 424.1 625.0
175 10.29 14.14 19.29 25.72 38.6 64.3 90.0 141.4 205.7 295.7 295.7 488.6 720.1
200 11.64 16.01 21.83 29.11 43.7 72.8 334.8
232 384.7

SIZING INSTRUCTIONS
HIGH PRESSURE METERS To select the proper meter size, use the Minimum Operating Pressure and the Maximum Instantaneous Hourly Flow Rate. Do not
MODEL 1M300 3M300 exceed meter’s maximum allowable operating pressure.
RATING 1000 3000 To prevent oversizing of a meter, sizing should be based upon the total connected load giving consideration to the load diversity.
PSIG Corrected Capacity at When using this method to size a meter, a selected diversity factor times the total connected load will be used as the Maximum
Metering Pressure — in MSCFH Instantaneous Flow Rate for sizing purposes.
125 9.5 28.4 A diversity factor of 0,85 is commonly used for a single application where two or more major appliances are in use (i,e, boilers,
furnaces, space heaters, etc,).
150 11.2 33.5
175 12.9 38.6 As the number of appliances considered when determining a connected load increases, the diversity factor will typically decrease.
For applications such as multiple ranges and water heaters, some examples of commonly used diversity factors are:
200 14.6 43.7
Qty Factor Qty Factor*
250 18.0 53.9 0-5 1 6 0.9
300 21.3 64.0 7 0.85 8 0.83
ENERGY VALUE
* The diversity factors listed above are estimates. Gas BTU/Cu. Ft.
NOTE: All capacities listed are Standard Cubic Feet per Hour (SCFH) For proper sizing, consult your company or industry Acetylene 1498
and based upon Average Atmospheric Pressure (14.4 PSIA), Base standards for determining accepted values. Butane 3200
Pressure (14.73 PSIA), and Base Temperature (60°F). Tables do not
take into account Supercompressibility. Please refer to RM-135 for Ethane 1758
further information on the Application of Temperature and/or Ethylene 1606
Pressure Correction Factors in Gas Measurement. Methane 997
Natural 965/1055
Propane 2550

30
Metric Sizing Charts

LINE MOUNTED - METRIC Foot Mount

MODEL 8C175* 11C175*15C175* 2M175* 3M175* 5M175* 7M175 11M175 16M175 23M232 23M175 38M175 56M175 102M125
*Also available in 200 PSIG Rating
RATING 22,7 31,2 42,5 56,6 85 141,6 198,2 311,5 453,1 651,3 651,3 1076 1585,7 2888,3
PSIG kPa BAR Corrected Capacity at Metering Pressure – in Nm3/H Corrected Capacity ateri
1 6,9 0,1 23,7 32,6 44,4 59,2 88,8 148,0 207,2 325,7 473,7 680,9 680,9 1125,0 1657,9 3019,7
3 20,7 0,2 26,8 36,8 50,2 66,9 100,3 167,2 234,1 368,0 535,2 769,3 769,3 1271,1 1873,2 3411,9
5 34,5 0,3 29,8 41,0 55,9 74,6 111,9 186,5 261,1 410,2 596,7 857,8 857,8 1417,2 2088,5 3804,0
10 68,9 0,7 37,5 51,6 70,4 93,8 140,7 234,5 328,3 516,0 750,5 1078,9 1078,9 1782,4 2626,8 4784,5
15 103,4 1,0 45,2 62,2 84,8 113,0 169,6 282,6 395,6 621,7 904,3 1299,9 1299,9 2147,7 3165,0 5764,9
20 137,9 1,4 52,9 72,7 99,2 132,3 198,4 330,6 462,9 727,4 1058,1 1521,0 1521,0 2513,0 3703,3 6745,3
30 206,8 2,1 68,3 93,9 128,0 170,7 256,1 426,8 597,5 938,9 1365,7 1963,2 1963,2 3243,5 4779,8 8706,1
40 275,8 2,8 83,6 115,0 156,8 209,1 313,7 522,9 732,1 1150,4 1673,3 2405,3 2405,3 3974,0 5856,4 10667,0
50 344,7 3,4 99,0 136,2 185,7 247,6 371,4 619,0 866,6 1361,8 1980,8 2847,5 2847,5 4704,5 6932,9 12627,8
60 413,7 4,1 114,4 157,3 214,5 286,0 429,1 715,1 1001,2 1573,3 2288,4 3289,6 3289,6 5435,0 8009,4 14588,7
70 482,6 4,8 129,8 178,5 243,3 324,5 486,7 811,2 1135,8 1784,8 2596,0 3731,8 3731,8 6165,5 9086,0 16549,5
80 551,6 5,5 145,2 199,6 272,2 362,9 544,4 907,3 1270,3 1996,2 2903,6 4173,9 4173,9 6896,0 10162,5 18510,3
90 620,5 6,2 160,5 220,8 301,0 401,4 602,1 1003,5 1404,9 2207,7 3211,2 4616,1 4616,1 7626,5 11239,1 20471,2
100 689,5 6,9 175,9 241,9 329,8 439,8 659,8 1099,6 1539,5 2419,2 3518,8 5058,2 5058,2 8357,0 12315,6 22432,0
125 861,8 8,6 214,4 294,8 401,9 535,9 803,9 1339,9 1875,9 2947,8 4287,7 6163,6 6163,6 10183,3 15006,9 27334,1
150 1034,2 10,3 252,8 347,7 474,0 632,0 948,1 1580,2 2212,3 3476,5 5056,7 7269,0 7269,0 12009,6 17698,3
175 1206,6 12,1 291,2 400,5 546,1 728,2 1092,3 1820,5 2548,7 4005,2 5825,6 8374,4 8374,4 13835,8 20389,6
200 1379,0 13,8 329,7 453,4 618,2 824,3 1236,5 2060,7 9479,7
232 1599,6 16,0 10894,6

HIGH PRESSURE METERS - METRIC

MODEL 1M300 3M300
RATING 28,3 85,0
PSIG Bar kPa Corrected Capacity at
Metering Pressure - in Nm3/H
125 861,8 8,6 268,0 803,9
150 1034,2 10,3 316,1 948,1
175 1206,6 12,1 364,1 1092,3
200 1379,0 13,8 412,2 1236,5
250 1723,7 17,2 508,3 1524,8
300 2068,4 20,7 604,5 1813,2

31
 Dresser Roots Meters & Instruments Dresser, Inc.
P. O. Box 42176 Inside US Ph: 800.521.1114 Fax: 800.335.5224
Houston, TX 77242-2176 Outside US Ph: 832.590.2303 Fax: 832.590.2494
website: www.dresser.com www.rootsmeters.com

©2003 Dresser, Inc.

ROOTS is a registered trademark of Dresser, Inc. IOM:B3
10.07