Whitemagic Lse805

Service Manual –LSE805-Philipines
Downloaded from www.Manualslib.com manuals search engine

INDEX
1.0 PROJECT BRIEF
2.0 PRODUCT BRIEF
3.0 PRODUCT SPECIFICATION
4.0 QUALITY IMPROVEMENTS
5.0 PRODUCT EXPLODED VIEW
6.0 WIRING DIAGRAM
7.0 CONTROL COMPONENTS & CHECKING GUIDE
8.0 TEST ROUTINES & ERROR CODES
9.0 INSTALLATION AND DEMO

1.0 Project brief

LSE805 – 7.5 kg ( Dry linen )
M1 – 6 programs( Steel basket)

Charter, Objectives and Key Drivers
Project Charter and Objectives
Develop,Manufacture and Deliver cost effective platform

to compete entry level 7.5 kg (dry linen) with Flush
“C”type according to the objectives of Quality,time and
cost specified for this project. 10
G I I
Shareholder Value
6.5
P G I
Key Drivers for this Project 3
P P G
0 3 6.5 10
Increases market share in exports FATL Customer Loyalty
Relevance
Consumer Benefits - New aesthetics & Value for money

2.0 Product brief

Model WhiteMagic
7.5 kg (dry linen)

Capacity
Platform size 540 x 540
Tub ID – φ (Existing WW)

OD- φ
(Existing WW)
Basket ID φ
Prime mover Agipeller
Styling GCD design
Lid GCD Glass Lid
Front R25 , Rear R14 , No Dishing

Cabinet
User Interface New – 123 Interface

3.0 Product Specifications

WHIRLPOOL Project Number #629555 2K8/16 Rev : 0C
LAUNDRY SALES RELEASE Model Year 2009 20/08/09
PRODUCT INFORMATION HOW SOLD
Washer -
Product Type Market Philliphines export
Top Load FA
Similar to Model WW Channel Current
Model Line-up Position Low End Segment
Original Release Date 29/10/08 Brand Whirlpool
Last Revision Date / Letter 17/08/09 Model Name Quartz
Factory Location Pondicherry
MODEL INFORMATION
MODEL M1(Ivory SS Basket)
Model code LSE805
Brand Whilrpool
Capacity 7.5kg Dry linen
Target Intro date Dec'09
Market : Export / Domestic Export

TECHNICAL SPECIFICATIONS
Power Supply 220 V AC ±10% 60 Hz
Wash Capacity
7.5kg Dry linen
Water Consumption (Full Cycle) 70-130 L

Power Consumption Per Wash
TBD
(Kw/H)
Safety Standard IEC 60335-1,IEC 60335-2-7,IEC 60335 -2-4
Spin Speed 760 rpm (Max)
Machine Dimension (WxDxH)

540 X 570 X 950
(mm)
Machine Weight 33 Kg
Input Power (Motor rating) 360W (Quartz motor)
Heater Rating NA
Wash / Spin Basket Ivory SS.basket
Water Inlet Valve Single

Water Pressure (Inlet water
0.2 Kg/cm2 to 7 Kg/cm2
supply)
Basket Volume 48 L
CISPR 14-1(EN 55014-1),CISPR 14-2 (EN 55014-
EMI/EMC
2),IEC 61000-3-2,IEC 61000-3-3
Vibration sensor No
Control Type Electronic
Waranty one year

STYLING & STRUCTURAL
Styling GCD Styling with glass lid design ,ABS non UV Grade
Top Flush type
Lid Glass Tempered with ceramic printing -Black printing
Glass Lid sticker Yes - TEMPERED GLASS (Same as Sapphire)
Escutcheon (GCD to provide artwork) - Greyish Blue matching to handle
Color Light grey-top and Greyish blue handle
Underbase Yes
Whirlpool Logo Al.dome Logo

WASH PERFORMANCE
Prime Mover(Need to understand
functional differences between
Agipeller
single action & dual action
agitator).
Internals Same as Quartz with Ivory SS basket
Agipeller / Impeller RPM 16-21 STR/min(Based on program)
Lint Filter Yes (Inbuilt Magic lint filter)
Detergent Dispenser Yes (Right of Top below the lid)
Bleach Dispenser Yes @ Top Area

Blue / Softener No
No. Of Wash Programs 6
Wash Program Description(Would
Normal/Speedy/Wool/Heavy/Stain wash/Aqua
require wash table for better
store
understanding)
Stain wash yes
Hot Wash Option No

Dynamic Soak: Yes
Double Rinse Yes
Delicate Spin Yes
Wool Cycle Yes(No woolmark cerification)
Speedy Yes

CONVENIENCE
Delay Wash : No
Memory back up: Yes
Manual Water Level Selection 4 levels
On-OFF Electronic
Start / Pause Yes
(Automatic water level selection ) No
6th Sense No
7-Segment Display No
Cycle Configuration Soak/Wash/Rinse/ Spin
Water Storage Yes (Aqua Store)

7 Degment Display No
Child lock: Yes
Rinse Hold/Water Saver Yes (Separate)(aqua save)
Foot Fixed - rubber foot
End Of Cycle Buzzer Yes

Rat Mesh Yes
Inlet hose Both ends threaded type
Tub Clean Yes
Add-On Utility Tray Nil
Drain Type Gravity

5.0 PRODUCT EXPLODED

FULL MACHINE ASSEMBLY
1

FULL MACHINE ASSEMBLY
Full Machine Assy

Sl.No Description Qty
1 Top assembly 1
2 Agipeller assembly 1
3 Basket assembly 1
4 Motor Plate and Tub support assembly 1
5 Suspension assembly 1
6 Cabinet assembly 1
7 Underbase assembly 1

TOP ASSEMBLY 15 14
3 2 1
13
16
12
11
10
6 9
7 8

TOP ASSEMBLY
TOP ASSY
Sl.No Part No Description Qty
1 P018730020A Top - Quartz 1
2 P018830030A Hinge Pin – Quartz 1
3 P014330040A Bush – White magic 2
4 P018730030A Side hole plug - Top 2
5 P018730040A Add on - Key pad activator 8
6 P018734160A PCB ASSY-M1-QUARTZ-220V/60Hz-PHILIPPINES 1
7 P018730050A Spacer PCB mounting 7
8 P018731020A Housing Dispenser - Quartz 1
9 S011320150D Screw-st4.2x13-c, Philips, Steel 7
10 P016131220A Logo lid 1
11 P018854010A Pressure sensor assembly 1
12 P016131180A Lid switch 1
13 P018854040A Power cord assy-10 Amps-Philippines 1
14 P018831040B Inlet valve assembly 1
15 S011320100D SCREW - ST 3.5 X 14.0 - F 11
16 P018760330A LID ASSY-QUARTZ-GREYISH BLUE 1

AGIPELLER ASSEMBLY

BOM AGIPELLER
ASSEMBLY
AGIPELLER ASSEMBLY
1 P0161100700 CAP - Agipeller 1
2 P018713040A Agipeller 1

BASKET
ASSEMBLY
3
4
5
6
7
8

BASKET
ASSEMBLY
Basket Assy
1 P010113020A Ba l a nce ri ng a s s embl y (APWH) 1
2 P018713010B BASKET WARPPER(SS) - IVORY 1
3 S011321000C SS-SCREW ST 4.2X13 BT-INTEG. WASHER 12
4 P018713020A BASKET BOTTOM (PLASTIC) - IVORY 1
5 P010113110B SADDLE BLOCK 1
6 P018813080C DRIVE HUB - 24" 1
7 P014313060D Ma gi cli nt fi l ter 2
8 S011280780A SCREW - M6 X 28 HEX HD - SS 6

MOTOR PLATE & TUB SUPPORT ASSEMBLY
1
1

MOTOR PLATE & TUB
SUPPORT ASSEMBLY
Tub , Motor plate and Tub Support

assembly
P01011200
1 0C Tub assembly 1
2 Motor Plate and Tub support assembly 1

TUB ASSEMBLY

TUB ASSEMBLY
TUB Assy
1 P010112000C Tub with air dome 1

MOTOR PLATE &
TUB SUPPORT
ASSEMBLY
14 3
4
13
5
12
6
11
8
10

MOTOR PLATE & TUB
SUPPORT ASSEMBLY
Motor Plate and Tub Support Assy

1 P0196110100 Drive Assy. FP60 Dlx / 123 1
2 P010111500D Bracket-Capacitor 1
3 S016150040B CAPACITOR-INDUCTANCE CAN 10 microfarad 1
4 P01011114 Brake assembly 1
5 P014311080A TORQUE MOTOR 1
6 P015210010A Hose 1
7 P018811150A DRIVE BELT - 60HZ 1
8 P018711010A Motor 1
9 P018711050A PULLEY FAN -QUARTZ -60HZ 1
10 P012911090A Plate Motor With Bearing 1
11 S011600010A Pulley 1
12 P010111180B Drain valve assembly 1
13 P010111400B CAM RING-SPLUTCH 1
14 P0112100500 Hose connector 1

SUSPENSION
ASSEMBLY
2 3

BOM SUSPENSION ASSEMBLY
Suspension Assy
1 P0101001502 Ball lower Suspension 4
2 P018707020A Suspension Back Assembly 2
3 P018707010A Suspension Front Assembly 2

CABINET ASSEMBLY
6
7
3

BOM CABINET ASSEMBLY
CABINET ASSEMBLY
1 P018721030A Cabinet quartz 1
2 P018721040A Handle 2
3 P018821040E Bridge plate 2
4 P018721070A Inspection cover 1
5 S0113203900 SCREW ST4.2X13 WITH INTEGRATED WASHER 6
6 P018721060A Top Holder-Quartz 4
7 P018721050A Gusset Top-Quartz 4

Machine Electrical Diagram
Quartz

Wiring Diagram

Component Checking Guide
Quartz

LIST OF COMPONENTS
LSE
Sl No Control Components Part Number Description 805
1 PSC Motor P018711 010A Motor x
2 Capacitor S016150040B CAPACITOR-INDUCTANCE CAN 10 microfarad x
3 Brake Actuator P014311 080A Torque Motor - WM x
4 Inlet Valve assembly P018831 040B Inlet Valve Assy x
5 Lid Switch P01 6131 180A Lid Switch x
6 Pressure Sensor P01 8854 010A Pressure sensor x
7 Power Cord Assembly P01 8854 040A Power Cord Assy Exports -220V/16A x
8 Wiring Harness P01 8716 010A Wiring Harness - Right x
9 Wiring Harness P01 8716 020A Wiring Harness - Left x

CHECKLIST OF CONTROL COMPONENTS
Sl No Control Part Number Description Parameter to be checked Equipment Value

Components
1 PSC Motor P018711010A Motor 1. Motor Coil Resistance Digital Across Resistance
a) CCW Winding (2 - 3) - Red Multimeter 2-3 41.5±7%Ω
b) CW Winding (2 - 1) - Yellow 2-1 41.5±7%Ω
2. Rotor Friction Manual There should not be
any friction.
3. Physical Damage Visual No physical damage
2 Capacitor S016150040B CAPACITOR- 1. Capacitance Value LCR Meter 9.3 µF

INDUCTANCE CAN 10
microfarad 2. Physical Damage Visual No physical damage
3 Brake P01431108 0A 1. Brake Actuator's Motor coil Digital 7.5 – 8.5 kΩ

Actuator Resistance Multimeter
4 Inlet Valve P018831040B Inlet Valve Assy 24" - 1.Inlet valve coil resistance Digital 4.3 – 4.6 kΩ
assembly Cold Multimeter
2.Inlet valve filter Manual Inlet valve filter should

be properly
assembled and free
from foreign objects
3.Rubber Seal Manual Rubber seal should be
properly assembled.
4.Physical Damage Visual No physical damage

CHECKLIST OF CONTROL COMPONENTS cont..
Sl Control Part Number Description Parameter to be Equipment Value
No Components checked
5 Lid Switch P01 6131 180A Lid Switch - 1. Switch contact Digital Actuator Resistance
Swift Resistance Multimeter Pressed 0Ω
Not Pressed ∞ (Infinite)
6 Wiring Harness P01 8716 010A Wiring Harness 1.Proper Crimping Visual Crimping should be proper
- Right
P01 8716 020A Wiring Harness 1.Proper Crimping Visual Crimping should be proper
- Left
7 Pressure P01 8854 010A Pressure Sensor 1. Pressure sensor Output Digital Multimeter 1. Measure pressure sensor
24" frequency frequency between ckt 2 and 4 and
Sensor
the frequency value is 25.10 -
25.35kHz @ Atmospheric pressure
2. For remaining pressure, refer the
values mentioned in detailed section
2. Pressure Sensor Hose Visual There should not be any kinking or

foreign object

CHECKLIST OF CONTROL COMPONENTS cont..
Sl Control Part Number Description Parameter to be checked Equipment Value

No Components
8 Power Cord P01 8854 040A Power Cord 1. Connectivity between Plug L (Line) Digital Multimeter 0Ω
Assy Exports - pin and L (Line terminal - Red wire)
220V/16A terminal
2. Connectivity between Plug N Digital Multimeter 0Ω

(Neutral) pin and N (Neutral terminal -
Black wire) terminal
3. Color Visual Black
4. Cord Length Steel rule 2m
5. Cable Cross Section Visual 0.8 mm2

POINTS TO REMEMBER
• Disconnect power to the machine before removing the components from the machine.
• Do not measure the resistance at powered on condition.
• Before measuring the resistance, remove the connector from the component.
• While measuring the resistance across the control component, measure across its terminal.

MOTOR + CAPACITOR
Basic Function:
• Transform electrical energy into mechanical energy (movement)
Circuit:
Electrical Parameter:
Motor type : Permanent Split Capacitor Motor
Nominal voltage : 230V AC
Locked Rotor Current : max.: 5 A
Nominal resistor (25°C) : 16.6Ω
Motor Capacitor : 9.3µF
Protective Inductor : 50µH
Power Output : 150W
Type : Class F
Connector Type:
Motor
Number of circuits : 3
Motor : MLX 3-ckt
Control unit : Mini-fit Jr 6-ckt Board-in connector (Load Connector - LC)
Capacitor
Capacitor : 6.3 x 0.8mm Tab terminal
Test:
Check the motor coil resistance as per the above value
Check the capacitance value of the capacitor as per the above mentioned value

BRAKE ACTUATOR
Basic Function:
• Used to drain water from the tub
• Used to release brake
Circuit:
Motor type : Permanent Magnet Synchronous type
Nominal power : < 4W
Nominal voltage : 230V
Nominal Current : <0.03A
Nominal resistor (25°C) : 7.5 – 8.5 kΩ
Inductance : 7.87 H
Connector Type:
Brake Actuator : 4.8 x 0.5 Tab Housing
Test:
Check the resistance of the brake actuator as per the above value

INLET VALVE
Basic Function:
• Open/close the water inlet flow.
Circuit:
Nominal power : 5.5VA
Nominal voltage : 230V AC
Nominal current : 25 mA ± 20%
Nominal resistor (20°C) : 4.3 – 4.6 kΩ
Inductance (open valve) : 10.5 – 11.10 H
Inductance (close valve) : 6.04 – 6.09 H
Connector Type:
Valve : 6.3 x 0.8 Tab
Test:
Check the resistance of the Inlet valve coil as per the above value

LID SWITCH
Basic Function:
It is the feedback about the Lid status (closed/opened).
Circuit:
Voltage : 5V DC
Type : Single Pole Single Throw (SPST) Normally Open Switch
Connector Type:
Lid Switch : 4.8 x 0.5 mm Tab
Control Unit : Mini-fit Jr 6-ckt Board-in connector (Signal Connector - SC)
Test:
Check the continuity across the Lid Switch Terminal
Actuator Resistance (Ω)

Pressed 0
Not Pressed ∞

PRESSURE SENSOR
Basic Function:
• The pressure sensor is the Frequency Transducer which coverts water level into frequency.
• Pressure sensor is used for sensing water level in the Tub.
• Used for Automatic water level selection.
• Proposed sensor works under the concept of:
-Output Frequency α (1/Pressure)
Voltage : nom: 5V DC
Type : Square Wave
Water Level 0 65±25 200±20 270±20 335±15 400±15

(mmWC)
Output Frequency 25.35 / 24.85 23.75 23.13 22.54 21.98
(kHz) 25.10
Connector Type:
Pressure sensor : Mini-fit Jr 4-ckt
Control Unit : Mini-fit Jr 4-ckt Board-in connector (Pressure Sensor Connector - PC)
Test:
Check the pressure sensor output frequency as per the above table

Machine Test Routines
Quartz

LIST OF TEST ROUTINES
For LSE805
Key Combination Test in

Sl Test Routine After Memory
Invoked from Keep For Whom Machine
No Name Press Twice Completion Retention
Press or Jig
1 Line Test Programming Program Special Programming 1. Line Machine Yes

Routine State Cycle State 2. Customer
Installation
3. Service
2 Shop Floor Programming Program Water Level Programming 1. Line Machine No
Demo Routine State State 2. Shop floor
Demo
3 Pressure Programming Water Level Start/Pause Programming 1. Line Machine No
Sensor State State 2. Service
Diagnostic
Routine
4 Spin Test Programming Wash Option Special Off State 1. Line Machine No
Routine State Cycle 2. Shop floor
Demo
3. Service
5 Count Check Off State Start/Pause Wash Option Off State 1. VQ Machine / No
Routine (To Proceed 2. Service Jig
(Software to next step
Version + Program
Burn-in Count) Key)
“Line Test Routine” is a mandatory test to be done after installing the machine in the customer place to check all the functions of the
machine.

LINE / SERVICE TEST ROUTINE
To invoke the Line Test routine the following sequence to be followed:
1. Bring the control to PROGRAMMING State from OFF State by pressing On/Off key.
2. Keep pressing the Program key, press the Special Cycle twice with interval between two key presses above 100 ms.
When this test routine is invoked

a. Program Group LEDs (Water Storage, Stain Wash, Heavy, Delicate, Speedy and Normal discrete LEDs),
b. Special Option Group LEDs (Tub Clean, Low Spin and Extra Rinse discrete LEDs),
c. Water Level Group LEDs (Low, Medium, High and Extra High discrete LEDs) and
d. Wash Option Group LEDs (Saver, Spin, Rinse, Wash and Agitronic Soak discrete LEDs) light up in a group one by one at 2 Hz rate.

LINE / SERVICE TEST ROUTINE cont..
Sequence for LSE805

Duration
Function Checked
(approx)
•Check whether all the 9 keys are open. 2” •All the keys and
LEDs
•Lid Switch 3” •Lid Switch
Close->Open->Close
(All LEDs will stop flashing and start glowing. They
will remain in the glowing state till lid open-closure
feedback is received.)
•Fill Low Level •Inlet Valve
•Pressure Sensor
•Agitation 5” •Motor CW
•Motor CCW
•Pressure Sensor
•Drain Reset •Brake Actuator
Level •Pressure Sensor
•Spin + Drain 10" •Motor CCW
•Brake Actuator
•Lid Switch
•Pressure Sensor
•Brake 6” •Brake Actuator
•EOC chime 5” •Buzzer
Control will proceed to next phase only when the test in the current step is passed.
In the failure state all actuators are switched OFF. The Safety mains relay shall be opened.

SHOP FLOOR DEMO ROUTINE
To invoke the Shop Floor Demo Routine the following sequence to be followed:
1. Bring the control to PROGRAMMING State from OFF State by pressing On/Off key.
2. Keep pressing the Program key, press the Water Level key twice with interval between two key presses above 100 ms.
When this test routine is invoked

a. Program Group LEDs (Water Storage, Stain Wash, Heavy, Delicate, Speedy and Normal discrete LEDs),
b. Special Option Group LEDs (Tub Clean, Low Spin and Extra Rinse discrete LEDs)
c. Water Level Group LEDs (Low, Medium, High and Extra High discrete LEDs) and
d. Wash Option Group LEDs (Agitronic Soak, Wash, Rinse, Spin and Saver discrete LEDs) light up in a group one by one at 2 Hz rate.

SHOP FLOOR DEMO ROUTINE cont..
Error Type Error
Under check Description End Time
-
1 LEDs LEDs 0:02
ZCD circuitry ZCD Absence of 4 cycles
Brownout circuitry Brownout Circuitry (TBD [4.1– 4.5V DC]) R PE

2 Inlet Valve circuitry Turn on Inlet valve 0:08
Pre Condition: NR E1
Pressure Sensor feedback should be with in the
range.
3 Inlet Valve circuitry Turn off the Inlet Valve 0:09
4 Motor CW Make stroke in CW direction 0:19

Motor CCW Make stroke in CCW direction
6 Brake Actuator Turn off 0:29

1. Motor
Turn On Brake Actuator
7 Spin Turn on Motor CCW 0:39
8 End of Cycle Turn off 0:46

1. Motor CCW
2. Brake Actuator
3. EOC

PRESSURE SENSOR DIAGNOSTIC ROUTINE
This routine is helpful for testing the Pressure Sensor function.

1) To invoke this routine, bring the control to PROGRAMMING State from OFF State by pressing On/Off key.
2) Keep pressing the Water Level key, press the Start/Pause key twice with interval between two key presses above 100 ms.
3)The following sequence has to be followed:
All the LEDs to be turned off during this routine.

This routine displays water level in liters in the machine on the seven-segment display for 2 seconds.
Switch on the Inlet Valve. Also display the water level in liters on the 7-segment display till the Extra High water level is reached.
Switch off Inlet Valve and Pause for 10 sec.
Switch on the drain until the pressure sensor input senses the reset level. Also, display the water level in liters on the 7-segment display.
Pause for 1 min (Drain is continuously ON).
Switch on spin for 1 min
Turn OFF Drain and Spin.
Turn ON EOC signal for 5 sec.
This routine cannot be activated during RUNNING / PAUSE / OFF State. It can be activated only in PROGRAMMING State.
NOTE: Since there is no Seven segment display in M1, the water level has to be monitored manually.

SPIN TEST ROUTINE
This routine is helpful to test the Spin Function in the production line.
To invoke this routine, bring the control to PROGRAMMING State from OFF State by pressing On/Off key.
1) Keep pressing the Wash Option key, press the Special Cycle key twice with interval between two key presses above 100 ms.
2)Provide a delay of 10 secs. The control goes for direct spin for 4 mins.
3)Spin LED to be continuously on and all other LEDs to be turned off.
4)Seven Segments should be turned off.
5)Once the cycle is completed, EOC beep to be generated.
6)The control should go to OFF state after EOC.
During Spin routine, lid switch has to be satisfied (Lid has to be closed). Pressure sensor input has to be in the reset level.
This routine cannot be activated during RUNNING / PAUSE State. It can be activated only during PROGRAMMING State.

COUNT CHECK ROUTINE
To enter Count Check Routine, follow below mentioned steps:

1) In the OFF State, Keep pressing Start/Pause key, press Wash Option key twice with interval between two key
presses above 100 ms.
2) Software version will be displayed with the Program LEDs glowing. (Binary sequence to be followed to indicate the
Software version using the Program group LEDs. For Eg: For Third Software version (S03) Stain Wash and Water
Storage discrete LEDs will glow – 000011; For S10, Delicate and Stain Wash discrete LEDs will glow - 001010 )
3) If Program key is pressed once, Burn in count is displayed with Wash Option LEDs.
4) If Burn in count is within 200, Saver discrete LED has to glow. For every 200 counts increase (till 1000 counts) in the
Burn in , a Wash Status LED should glow in the order of Saver, Spin, Rinse, Wash and Agitronic Soak. (For Example:
If the count is 340, Spin LED should glow and similarly if the Burn in count is 660, Wash LED should start glowing.)
4) If Program key is pressed once, then the control will indicate the If Program key is pressed again, control will enter
Off state.

ERROR CODES
Quartz

ERROR DISPLAY FOR LSE805
Error type Beeper timings LED display

Lid Open during wash, Rinse and Beep 1.5 s – Off 5 s This Cycle status LEDs should start flashing at
Spin sequence to be repeated until the 1Hz rate.
lid is closed.
Long drain (Pressure sensor not 500 ms on – 500 ms off Wash Option group LEDs should flash at
detecting the Reset level even after Above sequence repeated every 2 Hz rate.
4 minutes of drain) 5 Seconds interval
Long Fill 500 ms on – 500 ms off Water Level group LEDs should flash at 2
Above sequence repeated every Hz rate.
5 seconds interval
Frequency output from the Pr. 500 ms on – 500 ms off Program group LEDs should flash at 2 Hz
Sensor out of Range Above sequence repeated every rate.
5 seconds interval
Key short circuit error 200 ms beep, 200 ms Off. All LEDs to be turned Off.
The sequence to be repeated
endlessly.
Invalid Key press Beep 100 ms – Off 100 ms –
Beep 100 ms,
Repeated until key is released

Installation of LSE805-60 Hz
1. Ensure all the 4 feets touch the floor evenly and corners are level with each other.
2. Donot place the machine on Slanting / uneven / unstable surface.
3. Place on a solid levelled surface to avoid excessive vibration during operation.
4. Keep the machine at least 10cm away from the wall on all sides.
5. Ensure the assembly of rat mesh at the time of installation.
6. Ensure Suspension bracket is removed from the machine before operation.
7. Ensure Inlet fill hose is connected to the Tap through tap adopter.
8. Place the drainhose flat on the floor before operating the machine.
9. Ensure the earth connection in your Electrical supply is proper before the
connecting the power cord. The socket should be standard and independent of 2
pin type of 220V/60 Hz.
10. Do not use extension junction box since it may not be properly earthed.

Preparation for Washing
a. Connect the fill hose to a water tap and turn the tap on.
b. Unhook the drainhose and lay it flat on the floor
c. Plug the powercord in to the electrical socket properly.
Loading the Machine
a. Separate Whites from colored clothes, and lint givers (eg: towels) from lint takers
(Dark color garments etc.,).
b. Donot stuff the clothes or wrap them around the agipeller – drop them loosely and evenly around the agipeller.
c. The clothes should be able to move freely in the water for best wash results.
d. Small clothes like hand kerchiefs or small towels should be loaded in the middle of the washer to avoid flying
of clothes during dry sensing operation.
Note :1) In case the ,the water pressure in very low (less than 5lpm), scatter the detergent in the bottom of the basket
before loading the clothes.
2) For Wool : Use Mild liquid detergent.

Machine operation
a. Press the power button to Switch On the machine

b. Select the desired program (6 programs). Press “Start” to begin the wash process
c. At the end of wash process,machine gives buzzer sound to indicate the wash process
completion to the consumer.

Thanks

Whitemagic Lse805

Uploaded by

Copyright:

Available Formats

Whitemagic Lse805

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Whitemagic Lse805

Uploaded by

Copyright:

Available Formats

Service Manual –LSE805-Philipines

Downloaded from www.Manualslib.com manuals search engine

1.0 PROJECT BRIEF

2.0 PRODUCT BRIEF

3.0 PRODUCT SPECIFICATION

4.0 QUALITY IMPROVEMENTS

5.0 PRODUCT EXPLODED VIEW

6.0 WIRING DIAGRAM

7.0 CONTROL COMPONENTS & CHECKING GUIDE

8.0 TEST ROUTINES & ERROR CODES

9.0 INSTALLATION AND DEMO

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

M1 – 6 programs( Steel basket)

Downloaded from www.Manualslib.com manuals search engine

Project Charter and Objectives

Develop,Manufacture and Deliver cost effective platform

Key Drivers for this Project 3

Increases market share in exports FATL Customer Loyalty

Consumer Benefits - New aesthetics & Value for money

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

7.5 kg (dry linen)

Platform size 540 x 540

Tub ID – φ (Existing WW)

Prime mover Agipeller

Styling GCD design

Lid GCD Glass Lid

Front R25 , Rear R14 , No Dishing

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Water Consumption (Full Cycle) 70-130 L

Spin Speed 760 rpm (Max)

Machine Dimension (WxDxH)

Input Power (Motor rating) 360W (Quartz motor)

Wash / Spin Basket Ivory SS.basket

Water Inlet Valve Single

Downloaded from www.Manualslib.com manuals search engine

Top Flush type

Lid Glass Tempered with ceramic printing -Black printing

Glass Lid sticker Yes - TEMPERED GLASS (Same as Sapphire)

Escutcheon (GCD to provide artwork) - Greyish Blue matching to handle

Color Light grey-top and Greyish blue handle

Whirlpool Logo Al.dome Logo

Downloaded from www.Manualslib.com manuals search engine

Lint Filter Yes (Inbuilt Magic lint filter)

Detergent Dispenser Yes (Right of Top below the lid)

Bleach Dispenser Yes @ Top Area

Stain wash yes

Hot Wash Option No

Downloaded from www.Manualslib.com manuals search engine

Cycle Configuration Soak/Wash/Rinse/ Spin

Water Storage Yes (Aqua Store)

Foot Fixed - rubber foot

End Of Cycle Buzzer Yes

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine