En10020 2000
En10020 2000
En10020 2000
ICS: 77.080.20
Correspondence The European Standard EN 10020:2000 has the status of French standard.
Analysis This document generally defines grades of steel by chemical composition in addition
to the main quality grades.
Descriptors Technical International Thesaurus: iron-and steel products, steels, alloy steels,
unalloyed steels, stainless steels, definitions, classifications, quality classes, grades:
quality, chemical composition.
Corrections
Published and distributed by Association Française de Normalisation (AFNOR — French standard institute) — 11, avenue Francis de Pressensé —
93571 Saint-Denis La Plaine Cedex — Tel.: + 33 (0)1 41 62 80 00 — Fax: + 33 (0)1 49 17 90 00 — www.afnor.fr
English version
Définition et classification des nuances d'acier Begriffsbestimmung für die Einteilung der Stähle
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
© 2000 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10020:2000 E
worldwide for CEN national Members.
Page 2
EN 10020:2000
Contents
Foreword......................................................................................................................................................................3
1 Scope ..............................................................................................................................................................4
2 Term and definition........................................................................................................................................4
3 Classification by chemical composition .....................................................................................................4
3.1 Applicable alloy contents..............................................................................................................................4
3.2 Definition of classes ......................................................................................................................................5
3.2.1 Non alloy steels..............................................................................................................................................5
3.2.2 Stainless steels ..............................................................................................................................................5
3.2.3 Other alloy steels ...........................................................................................................................................5
4 Classification of main quality classes .........................................................................................................6
4.1 Non alloy steels..............................................................................................................................................6
4.1.1 Non alloy quality steels .................................................................................................................................6
4.1.2 Non alloy special steels ................................................................................................................................6
4.2 Stainless steels ..............................................................................................................................................7
4.3 Other alloy steels ...........................................................................................................................................7
4.3.1 Alloy quality steels ........................................................................................................................................7
4.3.2 Alloy special steels........................................................................................................................................8
Page 3
EN 10020:2000
Foreword
This European Standard has been prepared by Technical Committee ECISS/TC 6 "Steels - Definition
and classification", the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2000, and conflicting national standards
shall be withdrawn at the latest by September 2000.
At the Co-ordination Committee (COCOR) meeting of May 31/June 1, 1995, ECISS decided to revise
EN 10020:1988.
That standard used EURONORM 20:1974 as the basis for work, revising it to align EN 10020 as far as
possible at that time :
with the Harmonised System nomenclature of the World Customs Organisation (WCO) ;
taking into account experience gained from using the EURONORM together with new developments
in the steel industry.
This European standard is more closely aligned with the Harmonised System in that the same limit
values have been adopted for alloy elements, together with deletion of the previous "70 % rule" for
specified combinations of elements.
One main quality class in EN 10020:1988, base steels, has been deleted and merged with non alloy
quality steels.
Further developments in the iron and steel industry and progress in European standardisation have also
been taken into account.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Czech Republic,
Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,
Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Page 4
EN 10020:2000
1 Scope
This European Standard defines the term "steel" (see clause 2) and classifies steel grades into :
non alloy, stainless steel and other alloy steels by chemical composition (see clause 3) ;
main quality classes (see clause 4) defined by main property or application characteristics for non alloy,
stainless and other alloy steels.
For the purposes of this standard, the following term and definition apply :
2.1
steel
material which contains by mass more iron than any other single element, having a carbon content generally less
than 2 % and containing other elements. A limited number of chromium steels may contain more than 2 % of
carbon, but 2 % is the usual dividing line between steel and cast iron.
For European standards the classification given in the product standard or specification applies regardless of the
steel which is actually produced, provided that the chemical composition complies with the requirements of the
standard concerned.
3.1.1 Classification is based on the ladle analysis specified in the product standard or specification and is
determined by the minimum value specified for each element.
3.1.2 Where for elements other than manganese a maximum value only is specified in the product standard or
specification for the ladle analysis, a value of 70 % of this maximum value shall be taken for classification as set
out in tables 1 and 2. For manganese see note a of table 1.
3.1.3 Where a product standard or specification is based on product analysis an equivalent ladle analysis is
calculated using the permitted deviations from ladle analysis specified in the product standard or specification or
corresponding European Standard or EURONORM.
3.1.4 In the absence of a product standard or specification or a precisely specified chemical composition,
classification is based on the actual ladle analysis reported by the manufacturer.
3.1.5 The results of product analysis may deviate from those of the ladle analysis to an extent permitted by the
appropriate product standard or specification (such deviations do not affect the classification of the steel as non
alloy or alloy).
If the product analysis indicates a value, which would place the steel in a class other than intended, then its
inclusion in the class originally intended shall be separately and reliably substantiated.
3.1.6 Composite or coated products are classified according to the specified chemical composition of the
product, which has been coated or clad.
3.1.7 For each alloy element, the specified, calculated or actual ladle analysis value is expressed to the same
number of decimal places as the corresponding limit value shown in table 1. For example in this European
Standard a specified range of 0,3 % to 0,5 % corresponds to a range of 0,30 % to 0,50 %. Similarly a specified
content of 2 % is taken to mean a content of 2,00 %.
Page 5
EN 10020:2000
Non alloy steels are steel grades in which none of the limit values in table 1 is reached by the contents as defined
in 3.1.
Stainless steels are steels with at least 10,5 % of chromium and max.1,2% of carbon .
Other alloy steels are steel grades not complying with the definition of stainless steels in which at least one of the
limit values in table 1 is reached by the contents as defined in 3.1.
Al Aluminium 0,30
B Boron 0,0008
Bi Bismuth 0,10
Co Cobalt 0,30
Cr Chromium 0,30
Cu Copper 0,40
La Lanthanides (each) 0,10
Mn Manganese 1,65 a)
Mo Molybdenum 0,08
Nb Niobium 0,06
Ni Nickel 0,30
Pb Lead 0,40
Se Selenium 0,10
Si Silicon 0,60
Te Tellurium 0,10
Ti Titanium 0,05
V Vanadium 0,10
W Tungsten 0,30
Zr Zirconium 0,05
Non alloy quality steels are steel grades which, in general, have specified property requirements such as, for
example, toughness, grain size control and/or formability.
4.1.1.2 Definition
Non alloy quality steels are non alloy steels other than those defined in 4.1.2.2 as non alloy special steels.
Non alloy electrical steels are defined as : non alloy quality steels with specified requirements for maximum values
of specific total loss or minimum values of magnetic induction, polarisation or permeability
Non alloy special steels have a higher degree of cleanness than quality steels particularly in respect of non-metallic
inclusions. In most cases they are intended for quenching and tempering or surface hardening and are
characterized by consistent response to such treatment. Precise control of chemical composition and special care
in manufacture and process control ensure improved properties to meet exacting requirements. These properties
which are generally in combination and within closely controlled limits include high or closely controlled yield
strength or hardenability values sometimes associated with suitability for cold forming, welding or toughness.
4.1.2.2 Definition
Non alloy special steels are steel grades, which comply with one or more of the following requirements :
specified hardness penetration depth or surface hardness in the quenched, quenched and tempered or
surface hardened condition ;
NOTE This class includes grades where the product standard or specification specifies such limitations of inclusions
subject to agreement at the time of ordering. However, specified through thickness reduction of area properties do not change
the classification of the original steel.
(e.g. rod for high strength springs, electrodes, tyre cord wire) ;
specified minimum impact strength on Charpy-V-notch test pieces at - 50 °C greater than 27 J for test pieces
1)
taken in the longitudinal direction or greater than 16 J for test pieces taken in the transverse direction ;
1)
If no impact value is specified at - 50 °C the value specified between - 50 °C and - 60 °C shall be used.
Page 7
EN 10020:2000
steels for nuclear reactors having the following specified elements simultaneously restricted on product
analysis to :
precipitation hardening steels with minimum specified carbon contents of 0,25 % or more in the ladle analysis
and a ferritic/pearlitic microstructure, containing one or more micro alloy elements such as niobium or
vanadium with contents less than the limit values for alloy steels. Precipitation hardening is generally achieved
by controlled cooling from the hot forming temperature ;
prestressing steels.
corrosion resisting ;
heat resisting ;
creep resisting.
Alloy quality steels are steel grades for which requirements exist with regard to, for example, toughness, grain size
control and/or formability.
Alloy quality steels are not generally intended for quenching and tempering or for surface hardening.
4.3.1.2 Definition
4.3.1.2.1 Weldable fine grained structural steels, including steels for pressure vessels and tubes, other than
those defined in 4.3.1.2.3 which meet all the following conditions :
alloy contents as defined by 3.1 are less than the limit values given in table 2 ;
specified minimum impact strength on Charpy-V-notch test pieces at - 50 °C 27 J for test pieces taken in the
1)
longitudinal direction or 16 J for test pieces taken in the transverse direction .
1) If no impact value is specified at – 50°C the value specified between – 50°C and –60°C shall be used.
Page 8
EN 10020:2000
Cr Chromium 0,50
Cu Copper 0,50
Mn Manganese 1,80
Mo Molybdenum 0,10
Nb Niobium 0,08
Ni Nickel 0,50
Ti Titanium 0,12
V Vanadium 0,12
Zr Zirconium 0,12
4.3.1.2.2 Alloy steels for rails, sheet piling and mining frames.
2)
4.3.1.2.3 Alloy steels for hot or cold rolled flat products for severe cold forming applications containing grain
3)
refining elements such as boron, niobium, titanium, vanadium and/or zirconium or dual phase steels .
4.3.1.2.4 Alloy steels in which copper is the only specified alloy element.
4.3.1.2.5 Alloy electrical steels are steels mainly containing silicon or silicon and aluminium as alloying elements
to meet specified requirements for maximum values of specific total loss or minimum values of magnetic induction,
polarisation or permeability
This class includes steel grades other than stainless steels for which are characterized by precise control of
chemical composition and particular conditions of manufacture and process control to ensure improved properties
which are frequently specified in combination and within closely controlled limits.
4.3.2.2 Definition
All other alloy steels, which are not excluded by the definition given in 4.3.1 for alloy quality steels are alloy special
steels.
Alloy special steels include alloy engineering steels and alloy steels for pressure vessels, bearing steels, tool
steels, high-speed steels, and steels with special physical properties such as ferritic-nickel steels with controlled
expansion coefficient, or electrical resistance steels.