Digital Logic Design (R17a0461) (1) - 7-130

NUMBER SYSTEM
Number system is a basis for counting varies items. Modern computers communicate and operate
with binary numbers which use only the digits 0 &1. Basic number system used by humans is Decimal
number system.
For Ex: Let us consider decimal number 18. This number is represented in binary as 10010.
We observe that binary number system take more digits to represent the decimal number. For large
numbers we have to deal with very large binary strings. So this fact gave rise to three new number systems.
i) Octal number systems
ii) Hexa Decimal number system
iii) Binary Coded Decimal number(BCD) system
To define any number system we have to specify
• Base of the number system such as 2,8,10 or 16.
• The base decides the total number of digits available in that number system.
• First digit in the number system is always zero and last digit in the number system is always
base-1.
Binary number system:

The binary number has a radix of 2. As r = 2, only two digits are needed, and these are 0 and 1. In
binary system weight is expressed as power of 2.
The left most bit, which has the greatest weight is called the Most Significant Bit (MSB). And the
right most bit which has the least weight is called Least Significant Bit (LSB).
DIGITAL LOGIC DESIGN Page no. 3

For Ex: 1001.012 = [ ( 1 ) × 23 ] + [ ( 0 ) × 22 ] + [ ( 0 ) × 21 ] + [ ( 1 ) × 20 ] + [ ( 0 ) × 2-1 ] + [
( 1 ) × 22 ]
1001.012 = [ 1 × 8 ] + [ 0 × 4 ] + [ 0 × 2 ] + [ 1 × 1 ] + [ 0 × 0.5 ] + [ 1 × 0.25 ]
1001.012 = 9.2510
Decimal Number system
The decimal system has ten symbols: 0,1,2,3,4,5,6,7,8,9. In other words, it has a base of 10.
Octal Number System
Digital systems operate only on binary numbers. Since binary numbers are often very long, two
shorthand notations, octal and hexadecimal, are used for representing large binary numbers. Octal systems
use a base or radix of 8. It uses first eight digits of decimal number system. Thus it has digits from 0 to 7.
Hexa Decimal Number System

The hexadecimal numbering system has a base of 16. There are 16 symbols. The decimal digits 0 to
9 are used as the first ten digits as in the decimal system, followed by the letters A, B, C, D, E and F, which
represent the values 10, 11,12,13,14 and 15 respectively.
Decima Binar Octal Hexadeci

l y mal
0 0000 0 0
1 0001 1 1
2 0010 2 2
3 0011 3 3
4 0100 4 4
5 0101 5 5
6 0110 6 6
7 0111 7 7
8 1000 10 8
9 1001 11 9
10 1010 12 A
11 1011 13 B
12 1100 14 C
13 1101 15 D
14 1110 16 E
15 1111 17 F

Number Base conversions
The human beings use decimal number system while computer uses binary number system.
Therefore it is necessary to convert decimal number system into its equivalent binary.
i) Binary to octal number conversion

ii) Binary to hexa decimal number conversion
iii) Octal to binary Conversion
iv) Hexa to binary conversion
v) Octal to Decimal conversion
Ex: convert 4057.068 to octal
=4x83+0x82+5x81+7x80+0x8-1+6x8-2
=2048+0+40+7+0+0.0937

=2095.093710
vi) Decimal to Octal Conversion
Ex: convert 378.9310 to octal
37810 to octal: Successive division:
8 | 378
|
8 |47 --- 2
|
8 |5 --- 7 ↑
|
0 --- 5
=5728
0.9310 to octal :
0.93x8=7.44
0.44x8=3.52 ↓
0.53x8=4.16
0.16x8=1.28
=0.73418
378.9310=572.73418
vii) Hexadecimal to Decimal Conversion
Ex: 5C716 to decimal
=(5x162)+(C x161)+ (7 x160)
=1280+192+7
=14710
viii) Decimal to Hexadecimal Conversion
Ex: 2598.67510
1 6 2598
16 162 -6
10 -2
= A26 (16)

0.67510=0.675x16 -- 10.8
=0.800x16 -- 12.8 ↓
=0.800x16 -- 12.8
=0.800x16 -- 12.8
=0.ACCC16
2598.67510 = A26.ACCC16
ix) Octal to hexadecimal conversion:
The simplest way is to first convert the given octal no. to binary & then the binary no. to
hexadecimal.
Ex: 756.6038
7 5 6 . 6 0 3
111 101 110 . 110 000 011
0001 1110 1110 . 1100 0001 1000
1 E E . C 1 8
x) Hexadecimal to octal conversion:
First convert the given hexadecimal no. to binary & then the binary no. to octal.
Ex: B9F.AE16
B 9 F . A E
1011 1001 1111 . 1010 1110
101 110 011 111 . 101 011 100
5 6 3 7 . 5 3 4
=5637.534
Complements:
In digital computers to simplify the subtraction operation & for logical manipulation complements
are used. There are two types of complements used in each radix system.
i) The radix complement or r’s complement

ii) The diminished radix complement or (r-1)’s complement

Representation of signed no.s binary arithmetic in computers:
• Two ways of rep signed no.s

1. Sign Magnitude form
2. Complemented form
• Two complimented forms
1. 1‘s compliment form
2. 2‘s compliment form
Advantage of performing subtraction by the compliment method is reduction in the hardware.(
instead of addition & subtraction only adding ckt‘s are needed.)
i. e, subtraction is also performed by adders only.
Instead of subtracting one no. from other the compliment of the subtrahend is added to
minuend. In sign magnitude form, an additional bit called the sign bit is placed in front of the no.
If the sign bit is 0, the no. is +ve, If it is a 1, the no is _ve.
Ex:
0 1 0 1 0 0 1
↓
Sign bit =+41 magnitude
↑
1 1 0 1 0 0 1
= -41
Note: manipulation is necessary to add a +ve no to a –ve no
Representation of signed no.s using 2’s or 1’s complement method:

If the no. is +ve, the magnitude is rep in its true binary form & a sign bit 0 is placed in
front of the MSB.I f the no is _ve , the magnitude is rep in its 2‘s or 1‘s compliment form &a
sign bit 1 is placed in front of the MSB.
Ex:
Given no. Sign mag form 2‘s comp form 1‘s comp form
01101 +13 +13 +13
010111 +23 +23 +23
10111 -7 -7 -8
1101010 -42 -22 -21

Special case in 2’s comp representation:
Whenever a signed no. has a 1 in the sign bit & all 0‘s for the magnitude bits, the decimal
equivalent is -2n , where n is the no of bits in the magnitude .
Ex: 1000= -8 & 10000=-16
Characteristics of 2’s compliment no.s:

Properties:
1. There is one unique zero
2. 2‘s comp of 0 is 0
3. The leftmost bit can‘t be used to express a quantity . it is a 0 no. is +ve.
4. For an n-bit word which includes the sign bit there are (2n-1-1) +ve integers,
2n-1 –ve integers & one 0 , for a total of 2n uniquestates.
5. Significant information is containd in the 1‘s of the +ve no.s & 0‘s of the _ve
no.s
6. A _ve no. may be converted into a +ve no. by finding its 2‘s comp.
Signed binary numbers:
Decimal Sign 2‘s comp form Sign 1‘s comp form Sign mag form
+7 0111 0111 0111
+6 0110 0110 0110
+5 0101 0101 0101
+4 0100 0100 0100
+3 0011 0011 0011
+2 0010 0010 0010
+1 0011 0011 0011
+0 0000 0000 0000
-0 -- 1111 1000
-1 1111 1110 1001
-2 1110 1101 1010
-3 1101 1100 1011
-4 1100 1011 1100
-5 1011 1010 1101
-6 1010 1001 1110
-7 1001 1000 1111
8 1000 -- --

Methods of obtaining 2’s comp of a no:
• In 3 ways
1. By obtaining the 1‘s comp of the given no. (by changing all 0‘s to 1‘s & 1‘s to 0‘s) &
then adding 1.
2. By subtracting the given n bit no N from 2n
3. Starting at the LSB , copying down each bit upto & including the first 1 bit
encountered , and complimenting the remaining bits.
Ex: Express -45 in 8 bit 2‘s comp form
+45 in 8 bit form is 00101101

I method:
1‘s comp of 00101101 & the add 1
00101101
11010010
+1
_ _ _ _ _ _ _ _ _ _
11010011 is 2‘s comp form

II method:
Subtract the given no. N from 2n
2n = 100000000
Subtract 45= -00101101
+1
__ _
11010011 is 2‘s comp
III method:
Original no: 00101101

Copy up to First 1 bit 1
Compliment remaining : 1101001
bits 11010011
Ex:

-73.75 in 12 bit 2‘compform
I method
01001001.1100
10110110.0011
+1
10110110.0100 is 2‘s
II method:
28 = 100000000.0000
Sub 73.75=-01001001.1100
10110110.0100 is 2‘s comp

III method :
Orginalno : 01001001.1100
Copy up to 1‘st bit 100
Comp the remaining bits: 10110110.0
10110110.0100
2’s compliment Arithmetic:
• The 2‘s comp system is used to rep –ve no.s using modulus arithmetic . The word length
of a computer is fixed. i.e, if a 4 bit no. is added to another 4 bit no . the result will be
only of 4 bits. Carry if any , from the fourth bit will overflow called the Modulus
arithmetic.
Ex:1100+1111=1011
• In the 2‘s compl subtraction, add the 2‘s comp of the subtrahend to the minuend . If there
is a carry out , ignore it , look at the sign bit I,e, MSB of the sum term .If the MSB is a
0, the result is positive.& it is in true binary form. If the MSB is a ` ( carry in or no carry
at all) the result is negative.& is in its 2‘s comp form. Take its 2‘s comp to find its
magnitude in binary.
Ex:Subtract 14 from 46 using 8 bit 2‘s comp arithmetic:

+14 = 00001110
-14 = 11110010 2‘s comp
+46 = 00101110
-14 =+11110010 2‘s comp form of -14

-32 (1)00100000 ignore carry
Ignore carry , The MSB is 0 . so the result is +ve. & is in normal binary
form. So the result is +00100000=+32.
EX: Add -75 to +26 using 8 bit 2‘s comp arithmetic
+75 = 01001011
-75 =10110101 2‘s comp
+26 = 00011010
2‘s comp form of -75
-75 =+10110101
-49 11001111 No carry
No carry , MSB is a 1, result is _ve & is in 2‘s comp. The magnitude is 2‘s comp of
11001111. i.e, 00110001 = 49. so result is -49
Ex: add -45.75 to +87.5 using 12 bit arithmetic

+87.5 = 01010111.1000
-45.75=+11010010.0100
-41.75 (1)00101001.1100 ignore carry

MSB is 0, result is +ve. =+41.75
1’s compliment of n number:

• It is obtained by simply complimenting each bit of the no,.& also , 1‘s comp of a
no, is subtracting each bit of the no. form 1.This complemented value rep the –
ve of the original no. One of the difficulties of using 1‘s comp is its rep o f
zero. Both 00000000 & its 1‘s comp 11111111 rep zero.
• The 00000000 called +ve zero& 11111111 called –ve zero.
Ex: -99 & -77.25 in 8 bit 1‘s comp
+99 = 01100011
-99 = 10011100
+77.25 = 01001101.0100
-77.25 = 10110010.1011
1’s compliment arithmetic:
In 1‘s comp subtraction, add the 1‘s comp of the subtrahend to the minuend. If there is a
carryout , bring the carry around & add it to the LSB called the end around carry. Look at the
sign bit (MSB) . If this is a 0, the result is +ve & is in true binary. If the MSB is a 1 ( carry or no
carry ), the result is –ve & is in its is comp form .Take its 1‘s comp to get the magnitude inn
binary.
Ex: Subtract 14 from 25 using 8 bit 1‘s EX: ADD -25 to +14
25 = 00011001 +14 = 00001110
-45 = 11110001 -25 =+11100110
+11 (1)00001010 -11 11110100
+1
No carry MSB =1
00001011 result=-ve=-1110
MSB is a 0 so result is +ve (binary )
=+1110
Binary codes
Binary codes are codes which are represented in binary system with modification from the
original ones.
Weighted Binary codes
Non Weighted Codes
Weighted binary codes are those which obey the positional weighting principles, each
position of the number represents a specific weight. The binary counting sequence is
an example.
Reflective Code
A code is said to be reflective when code for 9 is complement for the code for 0, and

so is for 8 and 1 codes, 7 and 2, 6 and 3, 5 and 4. Codes 2421, 5211, and excess-3 are
reflective, whereas the 8421 code is not.
Sequential Codes
A code is said to be sequential when two subsequent codes, seen as numbers in binary
representation, differ by one. This greatly aids mathematical manipulation of data. The 8421 and
Excess-3 codes are sequential, whereas the 2421 and 5211 codes are not.
Non weighted codes
Non weighted codes are codes that are not positionally weighted. That is, each
position within the binary number is not assigned a fixed value. Ex: Excess-3 code
Excess-3 Code
Excess-3 is a non weighted code used to express decimal numbers. The code derives
its name from the fact that each binary code is the corresponding 8421 code plus
0011(3).
Gray Code
The gray code belongs to a class of codes called minimum change codes, in
which only one bit in the code changes when moving from one code to the next. The
Gray code is non-weighted code, as the position of bit does not contain any weight.
The gray code is a reflective digital code which has the special property that any two
subsequent numbers codes differ by only one bit. This is also called a unit- distance
code. In digital Gray code has got a special place.

Binary to Gray Conversion
Gray Code MSB is binary code MSB.

Gray Code MSB-1 is the XOR of binary code MSB and MSB-1.
MSB-2 bit of gray code is XOR of MSB-1 and MSB-2 bit of binary code.
MSB-N bit of gray code is XOR of MSB-N-1 and MSB-N bit of binary code.
8421 BCD code ( Natural BCD code):
Each decimal digit 0 through 9 is coded by a 4 bit binary no. called natural binary codes.
Because of the 8,4,2,1 weights attached to it. It is a weighted code & also sequential . it is useful
for mathematical operations. The advantage of this code is its case of conversion to & from
decimal. It is less efficient than the pure binary, it require more bits.
Ex: 14→1110 in binary
But as 0001 0100 in 8421 ode.
The disadvantage of the BCD code is that , arithmetic operations are more complex than
they are in pure binary . There are 6 illegal combinations 1010,1011,1100,1101,1110,1111 in
these codes, they are not part of the 8421 BCD code system . The disadvantage of 8421 code is,
the rules of binary addition 8421 no, but only to the individual 4 bit groups.
BCD Addition:
It is individually adding the corresponding digits of the decimal no,s expressed in

4 bit binary groups starting from the LSD . If there is no carry & the sum term is not an illegal
code , no correction is needed .If there is a carry out of one group to the next group or if the sum
term is an illegal code then 610(0100) is added to the sum term of that group & the resulting carry
is added to the next group.
Ex: Perform decimal additions in 8421 code

(a)25+13
In BCD 25= 0010 0101
In BCD +13 =+0001 0011
38 0011 1000
No carry , no illegal code .This is the corrected sum

(b). 679.6 + 536.8
679.6 = 0110 0111 1001 .0110 in BCD
+536.8 = +0101 0011 0010 .1000 in BCD
_ __ _________________
1216.4 1011 1010 0110 . 1110 illegal codes
+0110 + 0011 +0110 . + 0110 add 0110 to each
(1)0001 (1)0000 (1)0101 . (1)0100 propagate carry

/ / / /
+1 +1 +1 +1
0001 0010 0001 0110 . 0100
1 2 1 6 . 4
BCD Subtraction:
Performed by subtracting the digits of each 4 bit group of the subtrahend the digits from
the corresponding 4- bit group of the minuend in binary starting from the LSD . if there is no
borrow from the next group , then 610(0110)is subtracted from the difference term of this group.
(a)38-15
In BCD 38= 0011 1000

In BCD -15 = -0001 0101
23 0010 0011
No borrow, so correct difference.
.(b) 206.7-147.8
206.7 = 0010 0000 0110 . 0111 in BCD

-147.8 = -0001 0100 0111 . 0110 in BCD
__ _______________ _
58.9 0000 1011 1110 . 1111 borrows are present
-0110 -0110 . -0110 subtract 0110
0101 1000 . 1001

BCD Subtraction using 9’s & 10’s compliment methods:
Form the 9‘s & 10‘s compliment of the decimal subtrahend & encode that no. in
the 8421 code . the resulting BCD no.s are then added.
EX: 305.5 – 168.8
305.5 = 305.5
-168.8= +83.1 9‘s comp of -168.8
__
(1)136.6
+1 end around carry
136.7 corrected difference
305.510 = 0011 0000 0101 . 0101
+831.110 = +1000 0011 0001 . 0001 9‘s comp of 16
_ _ _ ________________ _ 8.8 in BCD
+1011 0011 0110 . 0110 1011 is illegal code
+0110 add 0110
(1)0001 0011 0110 . 0110

+1 End around carry
0001 0011 0110 . 0111

= 136.7
Excess three(xs-3)code:
It is a non-weighted BCD code .Each binary codeword is the corresponding 8421

codeword plus 0011(3).It is a sequential code & therefore , can be used for arithmetic
operations..It is a self-complementing code.s o the subtraction by the method of compliment
addition is more direct in xs-3 code than that in 8421 code. The xs-3 code has six invalid states
0000,0010,1101,1110,1111.. It has interesting properties when used in addition & subtraction.
Excess-3 Addition:
Add the xs-3 no.s by adding the 4 bit groups in each column starting from the LSD. If
there is no carry starting from the addition of any of the 4-bit groups , subtract 0011 from the
sum term of those groups ( because when 2 decimal digits are added in xs-3 & there is no carry ,
result in xs-6). If there is a carry out, add 0011 to the sum term of those groups( because when
there is a carry, the invalid states are skipped and the result is normal binary).
EX: 37 0110 1010
+28 +0101 1011
_ _ _ _ _ _ _ _ _ _
65 1011 (1)0101 carry generated

+1 propagate carry
_____ _
1100 0101 add 0011 to correct 0101 &

-0011 +0011 subtract 0011 to correct 1100
_______ _
1001 1000 =6510
Excess -3 (XS-3) Subtraction:
Subtract the xs-3 no.s by subtracting each 4 bit group of the subtrahend from the
corresponding 4 bit group of the minuend starting form the LSD .if there is no borrow from the
next 4-bit group add 0011 to the difference term of such groups (because when decimal digits are
subtracted in xs-3 & there is no borrow , result is normal binary). I f there is a borrow , subtract
0011 from the differenceterm(b coz taking a borrow is equivalent to adding six invalid states ,
result is in xs-6)
Ex: 267-175
267 = 0101 1001 1010

-175= -0100 1010 1000
_ _ ___ ___
0000 1111 0010

+0011 -0011 +0011
0011 1100 +0011 =9210

Xs-3 subtraction using 9’s & 10’s compliment methods:
Subtraction is performed by the 9‘s compliment or 10‘s compliment
Ex:687-348 The subtrahend (348) xs -3 code & its compliment are:
9‘s comp of 348 = 651

Xs-3 code of 348 = 0110 0111 1011
1‘s comp of 348 in xs-3 = 1001 1000 0100
Xs=3 code of 348 in xs=3 = 1001 1000 0100
687 687
-348 → +651 9‘s compl of 348
339 (1)338
+1 end around carry
_
339 corrected difference in decimal
1001 1011 1010 687 in xs-3

+1001 1000 0100 1‘s comp 348 in xs-3
_ _______ __
_ (1)0010 (1)0011 1110 carry generated
⁄⁄
+1 +1 propagate carry
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _-
(1)0011 0010 1110

+1 end around carry
_____________ _
0011 0011 1111 (correct 1111 by sub0011 and

+0011 +0011 +0011 correct both groups of 0011 by
__ _ ____ _ _ _ adding 0011)
__
0110 0110 1100 corrected diff in xs-3 = 33010

The Gray code (reflective –code):
Gray code is a non-weighted code & is not suitable for arithmetic operations. It is not a
BCD code . It is a cyclic code because successive code words in this code differ in one bit
position only i.e, it is a unit distance code.Popular of the unit distance code.It is also a reflective
code i.e,both reflective & unit distance. The n least significant bits for 2 n through 2n+1-1 are the
mirror images of thosr for 0 through 2n-1.An N bit gray code can be obtained by reflecting an N-
1 bit code about an axis at the end of the code, & putting the MSB of 0 above the axis & the
MSB of 1 below the axis.
Reflection of gray codes:
Gray Code
1 bit 2 bit 3 bit 4 bit Decimal 4 bit binary
0 00 000 0000 0 0000
1 01 001 0001 1 0001
11 011 0011 2 0010
10 010 0010 3 0011
110 0110 4 0100
111 0111 5 0101
101 0101 6 0110
110 0100 7 0111
1100 8 1000
1101 9 1001
1111 10 1010
1110 11 1011
1010 12 1100
1011 13 1101
1001 14 1110
1000 15 1111

Binary codes block diagram
Error – Detecting codes: When binary data is transmitted & processed,it is susceptible to noise
that can alter or distort its contents. The 1‘s may get changed to 0‘s & 1‘s .because digital
systems must be accurate to the digit, error can pose a problem. Several schemes have been
devised to detect the occurrence of a single bit error in a binary word, so that whenever such an
error occurs the concerned binary word can be corrected & retransmitted.
Parity: The simplest techniques for detecting errors is that of adding an extra bit known as parity
bit to each word being transmitted.Two types of parity: Oddparity, evenparity forodd parity, the
parity bit is set to a ‗0‘ or a ‗1‘ at the transmitter such that the total no. of 1 bit in the word
including the parity bit is an odd no.For even parity, the parity bit is set to a ‗0‘ or a ‗1‘ at the
transmitter such that the parity bit is an even no.
Decimal 8421 code Odd parity Even parity

0 0000 1 0
1 0001 0 1
2 0010 0 1
3 0011 1 0
4 0100 0 1
5 0100 1 0
6 0110 1 0
7 0111 0 1
8 1000 0 1
9 1001 1 0
When the digit data is received . a parity checking circuit generates an error signal if the
total no of 1‘s is even in an odd parity system or odd in an even parity system. This parity check
can always detect a single bit error but cannot detect 2 or more errors with in the same word.Odd
parity is used more often than even parity does not detect the situation. Where all 0‘s are created
by a short ckt or some other fault condition.
Ex: Even parity scheme

(a) 10101010 (b) 11110110 (c)10111001
Ans:
(a) No. of 1‘s in the word is even is 4 so there is no error
(b) No. of 1‘s in the word is even is 6 so there is no error
(c) No. of 1‘s in the word is odd is 5 so there is error
Ex: odd parity

(a)10110111 (b) 10011010 (c)11101010
Ans:
(a) No. of 1‘s in the word is even is 6 so word has error
(b) No. of 1‘s in the word is even is 4 so word has error
(c) No. of 1‘s in the word is odd is 5 so there is no error
Checksums:
Simple parity can‘t detect two errors within the same word. To overcome this, use a sort
of 2 dimensional parity. As each word is transmitted, it is added to the sum of the previously
transmitted words, and the sum retained at the transmitter end. At the end of transmission, the
sum called the check sum. Up to that time sent to the receiver. The receiver can check its sum
with the transmitted sum. If the two sums are the same, then no errors were detected at the
receiver end. If there is an error, the receiving location can ask for retransmission of the entire
data, used in teleprocessing systems.
Block parity:
Block of data shown is create the row & column parity bits for the data using odd parity.
The parity bit 0 or 1 is added column wise & row wise such that the total no. of 1‘s in each
column & row including the data bits & parity bit is odd as

Data Parity bit data
10110 0 10110
10001 1 10001
10101 0 10101
00010 0 00010
11000 1 11000
00000 1 00000
11010 0 11010
Error –Correcting Codes:
A code is said to be an error –correcting code, if the code word can always be deduced
from an erroneous word. For a code to be a single bit error correcting code, the minimum
distance of that code must be three. The minimum distance of that code is the smallest no. of bits
by which any two code words must differ. A code with minimum distance of 3 can‘t only correct
single bit errors but also detect ( can‘t correct) two bit errors, The key to error correction is that
it must be possible to detect & locate erroneous that it must be possible to detect & locate
erroneous digits. If the location of an error has been determined. Then by complementing the
erroneous digit, the message can be corrected , error correcting , code is the Hamming code , In
this , to each group of m information or message or data bits, K parity checking bits denoted by
P1,P2,----------pk located at positions 2 k-1 from left are added to form an (m+k) bit code word.
To correct the error, k parity checks are performed on selected digits of each code word, & the
position of the error bit is located by forming an error word, & the error bit is then
complemented. The k bit error word is generated by putting a 0 or a 1 in the 2 k-1th position
depending upon whether the check for parity involving the parity bit Pk is satisfied or not.Error
positions & their corresponding values :

Error Position For 15 bit code For 12 bit code For 7 bit code
C4 C3 C2 C1 C4 C3 C2 C1 C3 C2 C1
0 0000 0000 000
1 0001 0001 001
2 0010 0010 010
3 0011 0011 011
4 0100 0100 100
5 0101 0101 101
6 0 1 10 0 1 10 1 10
7 0 1 1 1 0 1 1 1 1 1 1
8 1 0 0 0 1 0 0 0
9 1 0 0 1 1 0 0 1
10 1 0 1 0 1 0 1 0
11 1 0 1 1 1 0 1 1
12 1 1 0 0 1 1 0 0
13 1 1 0 1
14 1 1 1 0
15 1 1 1 1
7- bit Hamming code:

To transmit four data bits, 3 parity bits located at positions 20 21&22 from left are
added to make a 7 bit codeword which is then transmitted.
The word format

P1 P2 D3 P4 D5 D6 D7
D—Data bits P-
Parity bits
Decimal Digit For BCD For Excess-3

P1P2D3P4D5D6D7 P1P2D3P4D5D6D7
0 0 0 0 0 0 0 0 1 0 0 0 0 1 1
1 1 1 0 1 0 0 1 1 0 0 1 1 0 0
2 0 1 0 1 0 1 1 0 1 0 0 1 0 1
3 1 0 0 0 0 1 1 1 1 0 0 1 1 0
4 1 0 0 1 1 0 0 0 0 0 1 1 1 1
5 0 1 0 0 1 0 1 1 1 1 0 0 0 0
6 1 1 0 0 1 1 0 0 0 1 1 0 0 1
7 0 0 0 1 1 1 1 1 0 1 1 0 1 0
8 1 1 1 0 0 0 0 0 1 1 0 0 1 1
9 0 0 1 1 0 0 1 0 1 1 1 1 0 0

Ex: Encode the data bits 1101 into the 7 bit even parity Hamming Code
The bit pattern is
P1P2D3P4D5D6D7
1 1 0 1
Bits 1,3,5,7 (P1 111) must have even parity, so P1 =1

Bits 2, 3, 6, 7(P2 101) must have even parity, so P2 =0
Bits 4,5,6,7 (P4 101)must have even parity, so P4 =0
The final code is 1010101
EX: Code word is 1001001
Bits 1,3,5,7 (C1 1001) →no error →put a 0 in the 1‘s position→C1=0
Bits 2, 3, 6, 7(C2 0001)) → error →put a 1 in the 2‘s position→C2=1
Bits 4,5,6,7 (C4 1001)) →no error →put a 0 in the 4‘s position→C3=0
15-bit Hamming Code: It transmit 11 data bits, 4 parity bits located 20 21 22 23
Word format is
P1 P2 D3 P4 D5 D6 D7 P8 D9 D10 D11 D12 D13 D14 D15
12-Bit Hamming Code:It transmit 8 data bits, 4 parity bits located at position 20 21 22 23
Word format is
P1 P2 D3 P4 D5 D6 D7 P8 D9 D10 D11 D12
Alphanumeric Codes:
These codes are used to encode the characteristics of alphabet in addition to the decimal
digits. It is used for transmitting data between computers & its I/O device such as printers,
keyboards & video display terminals.Popular modern alphanumeric codes are ASCII code &
EBCDIC code.

Digital Logic Gates
Boolean functions are expressed in terms of AND, OR, and NOT operations, it is easier to
implement a Boolean function with these type of gates.

Properties of XOR Gates
• XOR (also ) : the “not-equal” function

• XOR(X,Y) = X  Y = X’Y + XY’
• Identities:
– X 0=X
– X  1 = X’
– X X=0
– X  X’ = 1
• Properties:
– X  Y= Y X
– (X  Y)  W = X  ( Y  W)
Universal Logic Gates
NAND and NOR gates are called Universal gates. All fundamental gates (NOT, AND, OR) can be
realized by using either only NAND or only NOR gate. A universal gate provides flexibility and
offers enormous advantage to logic designers.
NAND as a Universal Gate

NAND Known as a “universal” gate because ANY digital circuit can be implemented with NAND
gates alone.
To prove the above, it suffices to show that AND, OR, and NOT can be implemented using
NAND gates only.

Boolean Algebra: In 1854, George Boole developed an algebraic system now called Boolean algebra. In
1938, Claude E. Shannon introduced a two‐valued Boolean algebra called switching algebra that
represented the properties of bistable electrical switching circuits. For the formal definition of Boolean
algebra, we shall employ the postulates formulated by E. V. Huntington in 1904.
Boolean algebra is a system of mathematical logic. It is an algebraic system consisting of the set of
elements (0, 1), two binary operators called OR, AND, and one unary operator NOT. It is the basic
mathematical tool in the analysis and synthesis of switching circuits. It is a way to express logic functions
algebraically.
Boolean algebra, like any other deductive mathematical system, may be defined with aset of elements, a
set of operators, and a number of unproved axioms or postulates. A set of elements is anycollection of
objects having a common property. If S is a set and x and y are certain objects, then x Î Sdenotes that x is
a member of the set S, and y ÏS denotes that y is not an element of S. A set with adenumerable number of
elements is specified by braces: A = {1,2,3,4}, i.e. the elements of set A are thenumbers 1, 2, 3, and 4. A
binary operator defined on a set S of elements is a rule that assigns to each pair ofelements from S a
unique element from S._ Example: In a*b=c, we say that * is a binary operator if it specifies a rule for
finding c from the pair (a,b)and also if a, b, c Î S.
Axioms and laws of Boolean algebra
Axioms or Postulates of Boolean algebra are a set of logical expressions that we accept without proof and
upon which we can build a set of useful theorems.
AND Operation OR Operation NOT Operation

Axiom1 : 0.0=0 0+0=0 0=1
Axiom2: 0.1=0 0+1=1 1=0
Axiom3: 1.0=0 1+0=1
Axiom4: 1.1=1 1+1=1
AND Law OR Law

Law1: A.0=0 (Null law) Law1: A+0=A
Law2: A.1=A (Identity law) Law2: A+1=1
Law3: A.A=A (Impotence law) Law3: A+A=A (Impotence law)
CLOSURE: The Boolean system is closed with respect to a binary operator if for every pair of
Boolean values,it produces a Boolean result. For example, logical AND is closed in the Boolean
system because it accepts only Boolean operands and produces only Boolean results.
_ A set S is closed with respect to a binary operator if, for every pair of elements of S, the binary
operator specifies a rule for obtaining a unique element of S.
_ For example, the set of natural numbers N = {1, 2, 3, 4, … 9} is closed with respect to the
binary operator plus (+) by the rule of arithmetic addition, since for any a, b Î N we obtain a
unique c Î N by the operation a + b = c.
ASSOCIATIVE LAW:
A binary operator * on a set S is said to be associative whenever (x * y) * z = x * (y * z) for all x, y, z Î S,

forall Boolean values x, y and z.
COMMUTATIVE LAW:
A binary operator * on a set S is said to be commutative whenever x * y = y * x for all x, y, z є S
IDENTITY ELEMENT:
A set S is said to have an identity element with respect to a binary operation * on S if there exists an element
e є S with the property e * x = x * e = x for every x є S
BASIC IDENTITIES OF BOOLEAN ALGEBRA

• Postulate 1(Definition): A Boolean algebra is a closed algebraic system containing a set K of two or more
elements and the two operators · and + which refer to logical AND and logical OR •x + 0 = x
• x ·0=0
• x+1=1
• x·1=1
• x+x=x
• x·x=x
• x + x’ = x
• x · x’ = 0
• x+y=y+x
• xy = yx
• x + ( y + z ) = (x + y) +z
• x (yz) = (xy) z
• x ( y + z ) = xy + xz
• x + yz = ( x + y )( x + z)
• ( x + y )’ = x’ y’
• ( xy )’ = x’ + y’
• (x’)’ = x
DeMorgan's Theorem
(a) (a + b)' = a'b'

(b) (ab)' = a' + b'
Generalized DeMorgan's Theorem

(a) (a + b + … z)' = a'b' … z'
(b) (a.b … z)' = a' + b' + … z‘
Basic Theorems and Properties of Boolean algebra Commutative law
Law1: A+B=B+A Law2: A.B=B.A
Associative law
Law1: A + (B +C) = (A +B) +C Law2: A(B.C) = (A.B)C
Distributive law
Law1: A.(B + C) = AB+ AC Law2: A + BC = (A + B).(A +C)
Absorption law
Law1: A +AB =A Law2: A(A +B) = A
Solution: A(1+B) Solution: A.A+A.B

A A+A.B
A(1+B)
A
Consensus Theorem
Theorem1. AB+ A’C + BC = AB + A’C Theorem2. (A+B). (A’+C).(B+C) =(A+B).( A’+C)
The BC term is called the consensus term and is redundant. The consensus term is formed from a
PAIR OF TERMS in which a variable (A) and its complement (A’) are present; the consensus
term is formed by multiplying the two terms and leaving out the selected variable and its
complement
Consensus Theorem1 Proof:
AB+A’C+BC=AB+A’C+(A+A’)BC
=AB+A’C+ABC+A’BC
=AB(1+C)+A’C(1+B)
= AB+ A’C
Principle of Duality
Each postulate consists of two expressions statement one expression is transformed into the
other by interchanging the operations (+) and (⋅) as well as the identity elements 0 and 1.
Such expressions are known as duals of each other.
If some equivalence is proved, then its dual is also immediately true.
If we prove: (x.x)+(x’+x’)=1, then we have by duality: (x+x)⋅(x’.x’)=0
The Huntington postulates were listed in pairs and designated by part (a) and part (b) in below
table.
Table for Postulates and Theorems of Boolean algebra
Part-A Part-B
A+0=A A.0=0
A+1=1 A.1=A
A+A=A (Impotence law) A.A=A (Impotence law)
̅=1
A+ A ̅=0
A. A
̅=A (double inversion law)
A --
Commutative law: A+B=B+A A.B=B.A
Associative law: A + (B +C) = (A +B) +C A(B.C) = (A.B)C
Distributive law: A.(B + C) = AB+ AC A + BC = (A + B).(A +C)
Absorption law: A +AB =A A(A +B) = A
DeMorgan Theorem:
̅ .B
̅ ̅ +B
(A.B) = = A ̅
(A+B) = A
Redundant Literal Rule: A+ A̅. B=A+B ̅A+B)=AB
A.(A
Consensus Theorem: AB+ A’C + BC = AB + A’C (A+B). (A’+C).(B+C) =(A+B).( A’+C)
Boolean Function
Boolean algebra is an algebra that deals with binary variables and logic operations.
A Boolean function described by an algebraic expression consists of binary variables, the
constants 0 and 1, and the logic operation symbols.
For a given value of the binary variables, the function can be equal to either 1 or 0.
F(vars) = expression
Set of binary Variables Operators (+, •, ‘)

Constants (0, 1)
Groupings (parenthesis)
Variables
Consider an example for the Boolean function
F1 = x + y’z
The function F1 is equal to 1 if x is equal to 1 or if both y’ and z are equal to 1. F1 is equal to 0
otherwise. The complement operation dictates that when y’ = 1, y = 0. Therefore, F1 = 1 if x = 1
or if y = 0 and z = 1.
A Boolean function expresses the logical relationship between binary variables and is evaluated
by determining the binary value of the expression for all possible values of the variables.
A Boolean function can be represented in a truth table. The number of rows in the truth
table is 2n, where n is the number of variables in the function. The binary combinations for the
truth table are obtained from the binary numbers by counting from 0 through 2 n - 1.
Truth Table for F1
x y z F1
0 0 0 0
0 0 1 1
0 1 0 0
0 1 1 0
1 0 0 1
1 0 1 1
1 Gate Implementation of F1 = x + y’z
1 1 0
1 1 1 1
Note:
Q: Let a function F() depend on n variables. How many rows are there in the truth table of F() ?
A: 2n rows, since there are 2n possible binary patterns/combinations for the n variables.
Truth Tables
• Enumerates all possible combinations of variable values and the corresponding function
value
• Truth tables for some arbitrary functions
F1(x,y,z), F2(x,y,z), and F3(x,y,z) are shown to the below.
x y z F1 F2 F3
0 0 0 0 1 1
0 0 1 0 0 1

0 1 0 0 0 1
0 1 1 0 1 1
1 0 0 0 1 0
1 0 1 0 1 0
1 1 0 0 0 0
1 1 1 1 0 1
• Truth table: a unique representation of a Boolean function

• If two functions have identical truth tables, the functions are equivalent (and vice-
versa).
• Truth tables can be used to prove equality theorems.
• However, the size of a truth table grows exponentially with the number of variables
involved, hence unwieldy. This motivates the use of Boolean Algebra.
Boolean expressions-NOT unique
Unlike truth tables, expressions epresenting
x y z F G
a Boolean function are NOT unique.
• Example: 0 0 0 1 1
– F(x,y,z) = x’•y’•z’ + x’•y•z’ +
0 0 1 0 0
x•y•z’
– G(x,y,z) = x’•y’•z’ + y•z’ 0 1 0 1 1
• The corresponding truth tables for
F() and G() are to the right. They are 0 1 1 0 0
identical. 1 0 0 0 0
• Thus, F() = G()
1 0 1 0 0
1 1 0 1 1
1 1 1 0 0
Algebraic Manipulation (Minimization of Boolean function)

• Boolean algebra is a useful tool for simplifying digital circuits.
• Why do it? Simpler can mean cheaper, smaller, faster.
• Example: Simplify F = x’yz + x’yz’ + xz.
F= x’yz + x’yz’ + xz
= x’y(z+z’) + xz
= x’y•1 + xz
= x’y + xz
• Example: Prove
x’y’z’ + x’yz’ + xyz’ = x’z’ + yz’
• Proof:
x’y’z’+ x’yz’+ xyz’
= x’y’z’ + x’yz’ + x’yz’ + xyz’
= x’z’(y’+y) + yz’(x’+x)
= x’z’•1 + yz’•1
= x’z’ + yz’
Complement of a Function
• The complement of a function is derived by interchanging (• and +), and (1 and 0), and
complementing each variable.
• Otherwise, interchange 1s to 0s in the truth table column showing F.
• The complement of a function IS NOT THE SAME as the dual of a function.
Example
• Find G(x,y,z), the complement of F(x,y,z) = xy’z’ + x’yz
Ans: G = F’ = (xy’z’ + x’yz)’
= (xy’z’)’ • (x’yz)’ DeMorgan
= (x’+y+z) • (x+y’+z’) DeMorgan again
Note: The complement of a function can also be derived by finding the function’s dual, and
then complementing all of the literals
Canonical and Standard Forms
We need to consider formal techniques for the simplification of Boolean functions.

Identical functions will have exactly the same canonical form.
• Minterms and Maxterms
• Sum-of-Minterms and Product-of- Maxterms
• Product and Sum terms
• Sum-of-Products (SOP) and Product-of-Sums (POS)
Definitions
Literal: A variable or its complement
Product term: literals connected by •
Sum term: literals connected by +
Minterm: a product term in which all the variables appear exactly once, either complemented or
uncomplemented.
Maxterm: a sum term in which all the variables appear exactly once, either complemented or
uncomplemented.
Canonical form: Boolean functions expressed as a sum of Minterms or product of Maxterms are said to be
in canonical form.
Minterm
• Represents exactly one combination in the truth table.
• Denoted by mj, where j is the decimal equivalent of the minterm’s corresponding binary
combination (bj).
• A variable in mj is complemented if its value in bj is 0, otherwise is uncomplemented.
Example: Assume 3 variables (A, B, C), and j=3. Then, bj = 011 and its corresponding minterm is denoted
by mj = A’BC
Maxterm
• Represents exactly one combination in the truth table.

• Denoted by Mj, where j is the decimal equivalent of the maxterm’s corresponding binary
combination (bj).
• A variable in Mj is complemented if its value in bj is 1, otherwise is uncomplemented.
Example: Assume 3 variables (A, B, C), and j=3. Then, bj = 011 and its corresponding maxterm is denoted
by Mj = A+B’+C’
Truth Table notation for Minterms and Maxterms
• Minterms and Maxterms are easy to denote using a truth table.
Example: Assume 3 variables x,y,z (order is fixed)
x y z Minterm Maxterm
0 0 0 x’y’z’ = m0 x+y+z = M0
0 0 1 x’y’z = m1 x+y+z’ = M1
0 1 0 x’yz’ = m2 x+y’+z = M2
0 1 1 x’yz = m3 x+y’+z’= M3
1 0 0 xy’z’ = m4 x’+y+z = M4
1 0 1 xy’z = m5 x’+y+z’ = M5
1 1 0 xyz’ = m6 x’+y’+z = M6
1 1 1 xyz = m7 x’+y’+z’ = M7
Canonical Forms
• Every function F() has two canonical forms:
– Canonical Sum-Of-Products (sum of minterms)
– Canonical Product-Of-Sums (product of maxterms)
Canonical Sum-Of-Products:
The minterms included are those mj such that F( ) = 1 in row j of the truth table for F( ).
Canonical Product-Of-Sums:
The maxterms included are those Mj such that F( ) = 0 in row j of the truth table for F( ).
Example a b c f1
Consider a Truth table for f1(a,b,c) at right 0 0 0 0
The canonical sum-of-products form for f1 is
0 0 1 1
f1(a,b,c) = m1 + m2 + m4 + m6
= a’b’c + a’bc’ + ab’c’ + abc’ 0 1 0 1
The canonical product-of-sums form for f1 is 0 1 1 0
f1(a,b,c) = M0 • M3 • M5 • M7
1 0 0 1
= (a+b+c)•(a+b’+c’)• (a’+b+c’)•(a’+b’+c’).
1 0 1 0
• Observe that: mj = Mj’ 1 1 0 1
1 1 1 0

Shorthand: ∑ and ∏
• f1(a,b,c) = ∑ m(1,2,4,6), where ∑ indicates that this is a sum-of-products form, and m(1,2,4,6)
indicates that the minterms to be included are m1, m2, m4, and m6.
• f1(a,b,c) = ∏ M(0,3,5,7), where ∏ indicates that this is a product-of-sums form, and M(0,3,5,7)
indicates that the maxterms to be included are M0, M3, M5, and M7.
• Since mj = Mj’ for any j,
∑ m(1,2,4,6) = ∏ M(0,3,5,7) = f1(a,b,c)
•
Conversion between Canonical Forms
• Replace ∑ with ∏ (or vice versa) and replace those j’s that appeared in the original form with those
that do not.
• Example:
f1(a,b,c)= a’b’c + a’bc’ + ab’c’ + abc’
= m1 + m2 + m4 + m6
= ∑(1,2,4,6)
= ∏(0,3,5,7)
= (a+b+c)•(a+b’+c’)•(a’+b+c’)•(a’+b’+c’)
Standard Forms
Another way to express Boolean functions is in standard form. In this configuration, the terms that form
the function may contain one, two, or any number of literals.
There are two types of standard forms: the sum of products and products of sums.
The sum of products is a Boolean expression containing AND terms, called product terms, with one or
more literals each. The sum denotes the ORing of these terms. An example of a function expressed as a
sum of products is
F1 = y’ + xy + x’yz’
The expression has three product terms, with one, two, and three literals. Their sum is, in effect, an OR
operation.
A product of sums is a Boolean expression containing OR terms, called sum terms. Each term may have any
number of literals. The product denotes the ANDing of these terms. An example of a function expressed as
a product of sums is
F2 = x(y’ + z)(x’ + y + z’)
This expression has three sum terms, with one, two, and three literals. The product is an AND operation.

Conversion of SOP from standard to canonical form
Example-1.
Express the Boolean function F = A + B’C as a sum of minterms.
Solution: The function has three variables: A, B, and C. The first term A is missing two variables; therefore,
A = A(B + B’) = AB + AB’
This function is still missing one variable, so
A = AB(C + C’) + AB’ (C + C’)
= ABC + ABC’ + AB’C + AB’C’
The second term B’C is missing one variable; hence,
B’C = B’C(A + A’) = AB’C + A’B’C
Combining all terms, we have
F = A + B’C
= ABC + ABC’ + AB’C + AB’C’+ A’B’C
But AB’C appears twice, and according to theorem (x + x = x), it is possible to remove one of those
occurrences. Rearranging the minterms in ascending order, we finally obtain
F = A’B’C + AB’C + AB’C + ABC’ + ABC
= m1 + m4 + m5 + m6 + m7
When a Boolean function is in its sum‐of‐minterms form, it is sometimes convenient to express the
function in the following brief notation:
F(A, B, C) = ∑m (1, 4, 5, 6, 7)
Example-2.
Express the Boolean function F = xy + x’z as a product of maxterms.
Solution: First, convert the function into OR terms by using the distributive law:
F = xy + x’z = (xy + x’)(xy + z)
= (x + x’)(y + x’)(x + z)(y + z)
= (x’+ y)(x + z)(y + z)
The function has three variables: x, y, and z. Each OR term is missing one variable; therefore,
x’+ y = x’ + y + zz’ = (x’ + y + z)(x’ + y + z’)
x + z = x + z + yy’ = (x + y + z)(x + y’ + z)
y + z = y + z + xx’ = (x + y + z)(x’ + y + z)
Combining all the terms and removing those which appear more than once, we finally obtain
F = (x + y + z)(x + y’ + z)(x’ + y + z)(x’ + y + z)
F= M0M2M4M5
A convenient way to express this function is as
follows: F(x, y, z) = πM(0, 2, 4, 5)
The product symbol, π, denotes the ANDing of maxterms; the numbers are the indices of the maxterms of
the function.

Unit-II
Minimization Techniques
Two-variable k-map:
A two-variable k-map can have 22=4 possible combinations of the input variables A and
B
. Each of these combinations, , B,A ,AB(in the SOP form) is called a minterm.
The minterm may be represented in terms of their decimal designations – m0 for , m1 for
B,m2 for A and m3 for AB, assuming that A represents the MSB. The letter m stands for
minterm and the subscript represents the decimal designation of the minterm. The presence or
absence of a minterm in the expression indicates that the output of the logic circuit assumes logic
1 or logic 0 level for that combination of input variables.
The expression f= ,+ B+A +AB , it can be expressed using min
term as F= m0+m2+m3=∑m(0,2,3)
Using Truth Table:
Minterm Inputs Output

A B F
0 0 0 1
1 0 1 0
2 1 0 1
3 1 1 1
A 1 in the output contains that particular minterm in its sum and a 0 in that column indicates that
the particular mintermdoes not appear in the expression for output . this information can also be
indicated by a two-variable k-map.
Mapping of SOP Expresions:
A two-variable k-map has 22=4 squares .These squares are called cells. Each square on the k-
map represents a unique minterm. The minterm designation of the squares are placed in any
square, indicates that the corresponding minterm does output expressions. And a 0 or no entry in
any square indicates that the corresponding minterm does not appear in the expression for output.
The minterms of a two-variable k-map

The mapping of the expressions =∑m(0,2,3)is
k-map of ∑m(0,2,3)
EX: Map the expressions f= B+A
F= m1+m2=∑m(1,2)The k-map is
Minimizations of SOP expressions:
To minimize Boolean expressions given in the SOP form by using the k-map, look for
adjacent adjacent squares having 1‘s minterms adjacent to each other, and combine them to form
larger squares to eliminate some variables. Two squares are said to be adjacent to each other, if
their minterms differ in only one variable. (i.e, B & A differ only in one variable. so they may
be combined to form a 2-square to eliminate the variable B.similarly all other.
The necessary condition for adjacency of minterms is that their decimal designations must
differ by a power of 2. A minterm can be combined with any number of minterms adjacent to it
to form larger squares. Two minterms which are adjacent to each other can be combined to form
a bigger square called a 2-square or a pair. This eliminates one variable – the variable that is not
common to both the minterms. For EX:
m0 and m1 can be combined to yield,
f1 = m0+m1= + B= (B+
)= m0 and m2 can be combined to yield,
f2 = m0+m2= + = ( + )=

f3= m1+m3= B+AB=B( + )=B
f4 = m2+m3=A +AB=A(B+ )=A
m0 ,m1 ,m2 and m3 can be combined to yield,
= + +A +AB
= (B+ ) +A(B+ )
= +A
=1
f1= f2= f3=B f4=A f5=1
The possible minterm groupings in a two-variable k-map.
Two 2-squares adjacent to each other can be combined to form a 4-square. A 4-square
eliminates 2 variables. A 4-square is called a quad. To read the squares on the map after
minimization, consider only those variables which remain constant through the square, and
ignore the variables which are varying. Write the non complemented variable if the variable is
remaining constant as a 1, and the complemented variable if the variable is remaining constant as
a 0, and write the variables as a product term. In the above figure f1 read as , because, along the
square , A remains constant as a 0, that is , as , where as B is changing from 0 to 1.
EX: Reduce the minterm f= +A +AB using mapping Expressed in terms of minterms, the
given expression is F=m0+m1+m2+ m3=m∑(0,1,3)& the figure shows the k-map for f and its
reduction . In one 2-square, A is constant as a 0 but B varies from a 0 to a 1, and in the other 2-
square, B is constant as a 1 but A varies from a 0 to a 1. So, the reduced expressions is +B.
It requires two gate inputs for realization as

f= +B (k-map in SOP form, and logic diagram.)

The main criterion in the design of a digital circuit is that its cost should be as low as
possible. For that the expression used to realize that circuit must be minimal.Since the cost is
proportional to number of gate inputs in the circuit in the circuit, an expression is considered
minimal only if it corresponds to the least possible number of gate inputs. & there is no
guarantee for that k-map in SOP is the real minimal. To obtain real minimal expression, obtain
the minimal expression both in SOP & POS form form by using k-maps and take the minimal of
these two minimals.
The 1‘s on the k-map indicate the presence of minterms in the output expressions, where
as the 0s indicate the absence of minterms .Since the absence of a minterm in the SOP expression
means the presense of the corresponding maxterm in the POS expression of the same .when a
SOP expression is plotted on the k-map, 0s or no entries on the k-map represent the maxterms.
To obtain the minimal expression in the POS form, consider the 0s on the k-map and follow the
procedure used for combining 1s. Also, since the absence of a maxterm in the POS expression
means the presence of the corresponding minterm in the SOP expression of the same , when a
POS expression is plotted on the k-map, 1s or no entries on the k-map represent the minterms.
Mapping of POS expressions:
Each sum term in the standard POS expression is called a maxterm. A function in two
variables (A, B) has four possible maxterms, A+B,A+ , +B, +
. They are represented as M0, M1, M2, and M3respectively. The uppercase letter M stands for
maxterm and its subscript denotes the decimal designation of that maxterm obtained by treating
the non-complemented variable as a 0 and the complemented variable as a 1 and putting them
side by side for reading the decimal equivalent of the binary number so formed.
For mapping a POS expression on to the k-map, 0s are placed in the squares
corresponding to the maxterms which are presented in the expression an d1s are placed in the
squares corresponding to the maxterm which are not present in the expression. The decimal
designation of the squares of the squares for maxterms is the same as that for the minterms. A
two-variable k-map & the associated maxterms are asthe maxterms of a two-variable k-map
The possible maxterm groupings in a two-variable k-map

Minimization of POS Expressions:
To obtain the minimal expression in POS form, map the given POS expression on to the
K-map and combine the adjacent 0s into as large squares as possible. Read the squares putting
the complemented variable if its value remains constant as a 1 and the non-complemented
variable if its value remains constant as a 0 along the entire square ( ignoring the variables which
do not remain constant throughout the square) and then write them as a sum term.
Various maxterm combinations and the corresponding reduced expressions are shown in
figure. In this f1 read as A because A remains constant as a 0 throughout the square and B
changes from a 0 to a 1. f2 is read as B‘ because B remains constant along the square as a 1 and
A changes from a 0 to a 1. f5
Is read as a 0 because both the variables are changing along the square.
Ex: Reduce the expression f=(A+B)(A+B‘)(A‘+B‘) using mapping.
The given expression in terms of maxterms is f=πM(0,1,3). It requires two gates inputs
for realization of the reduced expression as
F=AB‘
K-map in POS form and logic diagram
In this given expression ,the maxterm M2 is absent. This is indicated by a 1 on the k-map. The
corresponding SOP expression is ∑m2 or AB‘. This realization is the same as that for the POS
form.
Three-variable K-map:
A function in three variables (A, B, C) expressed in the standard SOP form can have eight
possible combinations: A B C , AB C,A BC ,A BC,AB C ,AB C,ABC , and ABC. Each one of these
combinations designate d by m0,m1,m2,m3,m4,m5,m6, and m7, respectively, is called a
minterm. A is the MSB of the minterm designator and C is the LSB.
In the standard POS form, the eight possible combinations are:A+B+C, A+B+C ,
A+B +C,A+B + C ,A + B+ C,A + B + C ,A + B + C,A + B + C . Each oneof these combinations
designated by M0, M1, M2, M3, M4, M5, M6, and M7respectively is called a maxterm. A is the
MSB of the maxterm designator and C is the LSB.
A three-variable k-map has, therefore, 8(=23) squares or cells, and each square on the
map represents a minterm or maxterm as shown in figure. The small number on the top right
corner of each cell indicates the minterm or maxterm designation.

The three-variable k-map.
The binary numbers along the top of the map indicate the condition of B and C for each
column. The binary number along the left side of the map against each row indicates the
condition of A for that row. For example, the binary number 01 on top of the second column in
fig indicates that the variable B appears in complemented form and the variable C in non-
complemented form in all the minterms in that column. The binary number 0 on the left of the
first row indicates that the variable A appears in complemented form in all the minterms in that
row, the binary numbers along the top of the k-map are not in normal binary order. They are,
infact, in the Gray code. This is to ensure that twophysically adjacent squares are really adjacent,
i.e., their minterms or maxterms differ by only one variable.
Ex: Map the expression f=: C+ + + +ABC
In the given expression , the minterms are : C=001=m1 ; =101=m5;

=010=m2;
=110=m6;ABC=111=m7.
So the expression is f=∑m(1,5,2,6,7)= ∑m(1,2,5,6,7). The corresponding k-map is
K-map in SOP form
Ex: Map the expression f= (A+B+C),( + + ) ( + + )(A + + )( + + )
In the given expression the maxterms are

:A+B+C=000=M0; + + =101=M5; + + = 111=M7; A + + =011=M3; + +
=110=M6.
So the expression is f = π M (0,5,7,3,6)= π M (0,3,5,6,7). The mapping of the expression is

K-map in POS form.
Minimization of SOP and POS expressions:
For reducing the Boolean expressions in SOP (POS) form plotted on the k-map, look
at the 1s (0s) present on the map. These represent the minterms (maxterms). Look for the
minterms (maxterms) adjacent to each other, in order to combine them into larger squares.
Combining of adjacent squares in a k-map containing 1s (or 0s) for the purpose of simplification
of a SOP (or POS)expression is called looping. Some of the minterms (maxterms) may have
many adjacencies. Always start with the minterms (maxterm) with the least number of
adjacencies and try to form as large as large a square as possible. The larger must form a
geometric square or rectangle. They can be formed even by wrapping around, but cannot be
formed by using diagonal configurations. Next consider the minterm (maxterm) with next to the
least number of adjacencies and form as large a square as possible. Continue this till all the
minterms (maxterms) are taken care of . A minterm (maxterm) can be part of any number of
squares if it is helpful in reduction. Read the minimal expression from the k-map, corresponding
to the squares formed. There can be more than one minimal expression.
Two squares are said to be adjacent to each other (since the binary designations along
the top of the map and those along the left side of the map are in Gray code), if they are
physically adjacent to each other, or can be made adjacent to each other by wrapping around.
For squares to be combinable into bigger squares it is essential but not sufficient that their
minterm designations must differ by a power of two.
General procedure to simplify the Boolean expressions:

1. Plot the k-map and place 1s(0s) corresponding to the minterms (maxterms) of the SOP
(POS) expression.
2. Check the k-map for 1s(0s) which are not adjacent to any other 1(0). They are isolated
minterms(maxterms) . They are to be read as they are because they cannot be combined
even into a 2-square.
3. Check for those 1s(0S) which are adjacent to only one other 1(0) and make them pairs (2
squares).
4. Check for quads (4 squares) and octets (8 squares) of adjacent 1s (0s) even if they contain
some 1s(0s) which have already been combined. They must geometrically form a square
or a rectangle.
5. Check for any 1s(0s) that have not been combined yet and combine them into bigger
squares if possible.
6. Form the minimal expression by summing (multiplying) the product the product (sum)
terms of all the groups.
Reading the K-maps:

While reading the reduced k-map in SOP (POS) form, the variable which remains
constant as 0 along the square is written as the complemented (non-complemented) variable and
the one which remains constant as 1 along the square is written as non-complemented
(complemented) variable and the term as a product (sum) term. All the product (sum) terms are
added (multiplied).
Some possible combinations of minterms and the corresponding minimal expressions
readfrom the k-maps are shown in fig: Here f6 is read as 1, because along the 8-square no
variable remains constant. F5 is read as , because, along the 4-square formed by0,m1,m2 and
m3 , the variables B and C are changing, and A remains constant as a 0. Algebraically,
f5= m0+m1+m2+m3
= + C+ +
= ( +C)+ B(C+ )
= + B
= ( +B)=
f3 is read as + , because in the 4-square formed by m0,m2,m6, and m4, the variable A and B
are changing , where as the variable C remains constant as a 0. So it is read as . In the 4-square
formed by m0, m1, m4, m5, A and C are changing but B remains constant as a 0. So it is read as
. So, the resultant expression for f3 is the sum of these two, i.e., + .
f1 is read as + + ,because in the 2-square formed by m0 and m4 , A is changing from a 0

to a 1. Whereas B and C remain constant as a 0. So it s read as . In the 2-square formed
by m0 and m1, C is changing from a 0 to a 1, whereas A and B remain constant as a 0. So it is
read as .In the 2-square formed by m0 and m2 , B is changing from a 0 to a 1 whereas A
and C remain constant as a 0. So, it is read as . Therefore, the resultant SOP
expression is
++
Some possible maxterm groupings and the corresponding minimal POS expressions read from
the k-map are
In this figure, along the 4-square formed by M1, M3, M7, M5, A and B are changing from a 0 to
a 1, where as C remains constant as a 1. SO it is read as . Along the 4-squad formed by M3,
M2, M7, and M6, variables A and C are changing from a 0 to a 1. But B remains constant as a 1.
So it is read as . The minimal expression is the product of these two terms , i.e., f1 = ( )( ).also
in this figure, along the 2-square formed by M4 and M6 , variable B is changing from a 0 to a 1,
while variable A remains constant as a 1 and variable C remains constant as a 0. SO, read it
as
+C. Similarly, the 2-square formed by M7 andM6 is read as + , while the 2-square formed
by M2 and M6 is read as +C. The minimal expression is the product of these sum terms, i.e, f2
=( + )+( + )+( +C)
Ex:Reduce the expression f=∑m(0,2,3,4,5,6) using mapping and implement it in AOI logic as
well as in NAND logic.The Sop k-map and its reduction , and the implementation of the minimal
expression using AOI logic and the corresponding NAND logic are shown in figures below
In SOP k-map, the reduction is done as:
1. m5 has only one adjacency m4 , so combine m5 and m4 into a square. Along this 2-square
A remains constant as 1 and B remains constant as 0 but C varies from 0 to 1. So read it
as A .
2. m3 has only one adjacency m2 , so combine m3 and m2 into a square. Along this 2-square
A remains constant as 0 and B remains constant as 1 but C varies from 1 to 0. So read it
as B.
3. m6 can form a 2-square with m2 and m4 can form a 2-square with m0, but observe that by
wrapping the map from left to right m0, m4 ,m2 ,m6 can form a 4-square. Out of these m2
andm4 have already been combined but they can be utilized again. So make it. Along this
4-square, A is changing from 0 to 1 and B is also changing from 0 to 1 but C is remaining
constant as 0. so read it as .
4. Write all the product terms in SOP form. So the minimal SOP expression is
fmin=
k-map AOI logic NAND logic

Four variable k-maps:
Four variable k-map expressions can have 24=16 possible combinations of input variables such
as , ,------------ABCD with minterm designations m0,m1 --------------------m15 respectively
in SOP form & A+B+C+D, A+B+C+ ,---------- + + + with maxterms M0,M1, ---------
-
-M15 respectively in POS form. It has 24=16 squares or cells.The binary number designations of
rows & columns are in the gray code. Here follows 01 & 10 follows 11 called Adjacency
ordering.
SOP form POS form
EX:

Five variable k-map:
Five variable k-map can have 25 =32 possible combinations of input variable as
, E,--------ABCDE with minterms m0, m1-----m31 respectively in SOP &
A+B+C+D+E, A+B+C+ ,---------- + + + + with maxterms M0,M1, -----------
5
M31 respectively in POS form. It has 2 =32 squares or cells of the k-map are divided into 2
blocks of
16 squares each.The left block represents minterms from m0 to m15 in which A is a 0, and the
right block represents minterms from m16 to m31 in which A is 1.The 5-variable k-map may
contain 2-squares, 4-squares , 8-squares , 16-squares or 32-squares involving these two blocks.
Squares are also considered adjacent in these two blocks, if when superimposing one block on
top of another, the squares coincide with one another.
Grouping s is

Ex: F=∑m(0,1,4,5,6,13,14,15,22,24,25,28,29,30,31) is SOP
POS is F=πM(2,3,7,8,9,10,11,12,16,17,18,19,20,21,23,26,27)
The real minimal expression is the minimal of the SOP and POS forms.
The reduction is done as
1. There is no isolated 1s
2. M12 can go only with m13. Form a 2-square which is read as A‘BCD‘
3. M0 can go with m2,m16 and m18 . so form a 4-square which is read as B‘C‘E‘
4. M20,m21,m17 and m16 form a 4-square which is read as AB‘D‘
5. M2,m3,m18,m19,m10,m11,m26 and m27 form an 8-square which is read as C‘d
6. Write all the product terms in SOP form.
So the minimal expression is
Fmin= A‘BCD‘+B‘C‘E‘+AB‘D‘+C‘D(16 inputs)
In the POS k-map ,the reduction is done as:
1. There are no isolated 0s
3.
4.M8
5. M28
6.M30
7. Sum terms in POS form. So the minimal expression in POS is
Fmin= A‘BcD‘+B‘C‘E‘+AB‘D‘+C‘D

Six variable k-map:
Six variable k-map can have 26 =64 combinations as , ,---------

---ABCDEF with minterms m0, m1-----m63 respectively in SOP & (A+B+C+D+E+F), ---------- (
+ + + + + ) with maxterms M0,M1, -----------M63 respectively in POS form. It has
6
2 =64 squares or cells of the k-map are divided into 4 blocks of 16 squares each.
Some possible groupings in a six variable k-map
Don’t care combinations:For certain input combinations, the value of the output is unspecified
either because the input combinations are invalid or because the precise value of the output is of
no consequence. The combinations for which the value of experiments are not specified are
called don‘t care combinations are invalid or because the precise value of the output is of no
consequence. The combinations for which the value of expressions is not specified are called
don‘t care combinations or Optional Combinations, such expressions stand incompletely
specified. The output is a don‘t care for these invalid combinations.
Ex:In XS-3 code system, the binary states 0000, 0001, 0010,1101,1110,1111 are unspecified. &
never occur called don‘t cares.
A standard SOP expression with don‘t cares can be converted into a standard POS
form by keeping the don‘t cares as they are & writing the missing minterms of the SOP form as
the maxterms of the POS form viceversa.
Don‘t cares denoted by ‗X‘ or ‗φ‘

Ex:f=∑m(1,5,6,12,13,14)+d(2,4)
Or f=π M(0,3,7,9,10,11,15).πd(2,4)
SOP minimal form fmin= +B +
POS minimal form fmin=(B+D)( +B)( +D)
=++++(+
Prime implicants, Essential Prime implicants, Redundant prime implicants:
Each square or rectangle made up of the bunch of adjacent minterms is called a subcube. Each of
these subcubes is called a Prime implicant (PI). The PI which contains at leastone which cannot
be covered by any other prime implicants is called as Essential Prime implicant (EPI).The PI
whose each 1 is covered at least by one EPI is called a Redundant Prime implicant (RPI). A PI
which is neither an EPI nor a RPI is called a Selective Prime implicant (SPI).
The function has unique MSP comprising EPI is
F(A,B,C,D)= CD+ABC+A D + B
The RPI ‗BD‘ may be included without changing the function but the resulting expression would
not be in minimal SOP(MSP) form.
Essential and Redundant Prime Implicants

F(A,B,C,D)=∑m(0,4,5,10,11,13,15) SPI are marked by dotted squares, shows
MSP form of a function need not be unique.
Essential and Selective Prime Implicants
Here, the MSP form is obtained by including two EPI‘s & selecting a set of SPI‘s to cover
remaining uncovered minterms 5,13,15. & these can be covered as
(A) (4,5) &(13,15) ---------- B +ABD

(B) (5,13) & (13,15) -------- B D+ABD
(C) (5,13) & (15,11) ------- B D+ACD
F(A,B,C,D)= +A C---------EPI‘s + B +ABD
(OR) F(A,B,C,D)= +A C---------EPI‘s + B D+ABD
(OR) F(A,B,C,D)= +A C---------EPI‘s + B D+ACD
False PI’s Essential False PI’s, Redundant False PI’s & Selective False PI’s:
The maxterms are called falseminterms. The PI‘s is obtained by using the maxterms are
called False PI‘s (FPI). The FPI which contains at least one ‗0‘ which can‘t be covered by only
other FPI is called an Essential False Prime implicant (ESPI)
F(A,B,C,D)= ∑m(0,1,2,3,4,8,12)
=π M(5,6,7,9,10,11,13,14,15)
Fmin= ( + )( + )( + )( + )
All the FPI, EFPI‘s as each of them contain atleast one ‗0‘ which can‘t be covered by any other
FPI

Essential False Prime implicants
Consider Function F(A,B,C,D)= π M(0,1,2,6,8,10,11,12)
Essential and Redundant False Prime Implicants
Mapping when the function is not expressed in minterms (maxterms):
An expression in k-map must be available as a sum (product) of minterms (maxterms). However

if not so expressed, it is not necessary to expand the expression algebraically into its minterms
(maxterms). Instead, expansion into minterms (maxterms) can be accomplished in the process of
entering the terms of the expression on the k-map.
Limitations of Karnaugh maps:
• Convenient as long as the number of variables does not exceed six.

• Manual technique, simplification process is heavily dependent on the human abilities.
Quine-Mccluskey Method:
It also known as Tabular method. It is more systematic method of minimizing expressions

of even larger number of variables. It is suitable for hand computation as well as computation by
machines i.e., programmable. . The procedure is based on repeated application of the combining
theorem.
PA+P =P (P is set of literals) on all adjacent pairs of terms, yields the set of all PI‘s from which
a minimal sum may be selected.
Consider expression
∑m(0,1,4,5)= + C+A +A C

First, second terms & third, fourth terms can be combined
( + )+ (C+ )= +A
Reduced to
( + )=
The same result can be obtained by combining m0& m4 & m1&m5 in first step & resulting terms
in the second step .
Procedure:
• Decimal Representation
• Don‘t cares
• PI chart
• EPI
• Dominating Rows & Columns
• Determination of Minimal expressions in comples cases.
Branching Method:

EX:

UNIT-III
COMBINATIONAL CIRCUITS
Combinational Logic
• Logic circuits for digital systems may be combinational or sequential.
• A combinational circuit consists of input variables, logic gates, and output variables.
For n input variables,there are 2n possible combinations of binary input variables .For
each possible input Combination ,there is one and only one possible output combination.A
combinational circuit can be described by m Boolean functions one for each output
variables.Usually the input s comes from flip-flops and outputs goto flip-flops.
Design Procedure:
1. The problem is stated

2.The number of available input variables and required output variables is
determined. 3.The input and output variables are assigned lettersymbols.
4.The truth table that defines the required relationship between inputs and outputs is derived.
5.The simplified Boolean function for each output is obtained.

Adders:
Digital computers perform variety of information processing tasks,the one is arithmetic

operations.And the most basic arithmetic operation is the addition of two binary digits.i.e, 4 basic
possible operations are:
0+0=0,0+1=1,1+0=1,1+1=10
The first three operations produce a sum whose length is one digit, but when augends and addend
bits are equal to 1,the binary sum consists of two digits.The higher significant bit of this result is
called a carry.A combinational circuit that performs the addition of two bits is called a half-
adder. One that performs the addition of 3 bits (two significant bits & previous carry) is called a
full adder.& 2 half adder can employ as a full-adder.
The Half Adder: A Half Adder is a combinational circuit with two binary inputs (augends and
addend bits and two binary outputs (sum and carry bits.) It adds the two inputs (A and B) and
produces the sum (S) and the carry (C) bits. It is an arithmetic operation of addition of two single
bit words.
The Sum(S) bit and the carry (C) bit, according to the rules of binary addition, the sum (S) is the
X-OR of A and B ( It represents the LSB of the sum). Therefore,
S=A𝐵+𝐴
The carry (C) is the AND of A and B (it is 0 unless both the inputs are 1).Therefore,
C=AB
A half-adder can be realized by using one X-OR gate and one AND gate a
Logic diagrams of half-adder

NAND LOGIC:
NOR Logic:
The Full Adder:
A Full-adder is a combinational circuit that adds two bits and a carry and outputs a sum
bit and a carry bit. To add two binary numbers, each having two or more bits, the LSBs can be
added by using a half-adder. The carry resulted from the addition of the LSBs is carried over to
the next significant column and added to the two bits in that column. So, in the second and
higher columns, the two data bits of that column and the carry bit generated from the addition in
the previous column need to be added.
The full-adder adds the bits A and B and the carry from the previous column called the
carry-in Cin and outputs the sum bit S and the carry bit called the carry-out Cout . The variable S
gives the value of the least significant bit of the sum. The variable Cout gives the output carry.The

eight rows under the input variables designate all possible combinations of 1s and 0s that these
variables may have. The 1s and 0s for the output variables are determined from the arithmetic
sum of the input bits. When all the bits are 0s , the output is 0. The S output is equal to 1 when
only 1 input is equal to 1 or when all the inputs are equal to 1. The Cout has a carry of 1 if two or
three inputs are equal to 1.
From the truth table, a circuit that will produce the correct sum and carry bits in response to
every possible combination of A,B and Cin is described by
S = ABCin + ABCin + ABCin + ABCin
Cout = ABCin + ABCin + ABCin + ABCin
and
S = A  B  Cin
Cout = ACin + BCin + AB
The sum term of the full-adder is the X-OR of A,B, and Cin, i.e, the sum bit the modulo
sum of the data bits in that column and the carry from the previous column. The logic diagram
of the full-adder using two X-OR gates and two AND gates (i.e, Two half adders) and one OR
gate is

Even though a full-adder can be constructed using two half-adders, the disadvantage is that the
bits must propagate through several gates in accession, which makes the total propagation delay
greater than that of the full-adder circuit using AOI logic.
The Full-adder neither can also be realized using universal logic, i.e., either only NAND gates or
only NOR gates as
NAND Logic:

NOR Logic:
Subtractors:
The subtraction of two binary numbers may be accomplished by taking the complement
of the subtrahend and adding it to the minuend. By this, the subtraction operation becomes an
addition operation and instead of having a separate circuit for subtraction, the adder itself can be
used to perform subtraction. This results in reduction of hardware. In subtraction, each
subtrahend bit of the number is subtracted from its corresponding significant minuend bit to form
a difference bit. If the minuend bit is smaller than the subtrahend bit, a 1 is borrowed from the
next significant position., that has been borrowed must be conveyed to the next higher pair of
bits by means of a signal coming out (output) of a given stage and going into (input) the next
higher stage.
The Half-Subtractor:
A Half-subtractor is a combinational circuit that subtracts one bit from the other and
produces the difference. It also has an output to specify if a 1 has been borrowed. . It is used to
subtract the LSB of the subtrahend from the LSB of the minuend when one binary number is
subtracted from the other.
A Half-subtractor is a combinational circuit with two inputs A and B and two

outputs d and b. d indicates the difference and b is the output signal generated that informs the
next stage that a 1 has been borrowed. When a bit B is subtracted from another bit A, a
difference bit (d) and a borrow bit (b) result according to the rules given as

The output borrow b is a 0 as long as A≥B. It is a 1 for A=0 and B=1. The d output is the result
of the arithmetic operation2b+A-B.
A circuit that produces the correct difference and borrow bits in response to every possible
combination of the two 1-bit numbers is , therefore ,
d=A𝐵+𝐴 and b=𝐴 B
That is, the difference bit is obtained by X-OR ing the two inputs, and the borrow bit is obtained
by ANDing the complement of the minuend with the subtrahend.Note that logic for this exactly
the same as the logic for output S in the half-adder.
A half-substractor can also be realized using universal logic either using only NAND gates or
using NOR gates as:
NAND Logic:
NOR Logic:

The Full-Subtractor:
The half-subtractor can be only for LSB subtraction. IF there is a borrow

during the subtraction of the LSBs, it affects the subtraction in the next higher column; the
subtrahend bit is subtracted from the minuend bit, considering the borrow from that column used
for the subtraction in the preceding column. Such a subtraction is performed by a full-subtractor.
It subtracts one bit (B) from another bit (A) , when already there is a borrow bi from this column
for the subtraction in the preceding column, and outputs the difference bit (d) and the borrow
bit(b) required from the next d and b. The two outputs present the difference and output borrow.
The 1s and 0s for the output variables are determined from the subtraction of A-B-bi.
From the truth table, a circuit that will produce the correct difference and borrow bits in response
to every possiblecombinations of A,B and bi is
A full-subtractor can be realized using X-OR gates and AOI gates as

The full subtractor can also be realized using universal logic either using only NAND gates or
using NOR gates as:
NAND Logic:
NOR Logic:
33
Binary Parallel Adder:
A binary parallel adder is a digital circuit that adds two binary numbers in parallel form
and produces the arithmetic sum of those numbers in parallel form. It consists of full adders
connected in a chain , with the output carry from each full-adder connected to the input carry of
the next full-adder in the chain.
The interconnection of four full-adder (FA) circuits to provide a 4-bit parallel adder. The
augends bits of A and addend bits of B are designated by subscript numbers from right to left,
with subscript 1 denoting the lower –order bit. The carries are connected in a chain through the
full-adders. The input carry to the adder is Cin and the output carry is C4. The S output generates
the required sum bits. When the 4-bit full-adder circuit is enclosed within an IC package, it has
four terminals for the augends bits, four terminals for the addend bits, four terminals for the sum
bits, and two terminals for the input and output carries. AN n-bit parallel adder requires n-full
adders. It can be constructed from 4-bit, 2-bit and 1-bit full adder ICs by cascading several
packages. The output carry from one package must be connected to the input carry of the one
with the next higher –order bits. The 4-bit full adder is a typical example of an MSI function.
Ripple carry adder:

In the parallel adder, the carry –out of each stage is connected to the carry-in of
the next stage. The sum and carry-out bits of any stage cannot be produced, until sometime after
the carry-in of that stage occurs. This is due to the propagation delays in the logic circuitry,
34
which lead to a time delay in the addition process. The carry propagation delay for each full-
adder is the time between the application of the carry-in and the occurrence of the carry-out.
The 4-bit parallel adder, the sum (S1) and carry-out (C1) bits given by FA1 are not valid, until
after the propagation delay of FA1. Similarly, the sum S2 and carry-out (C2) bits given by FA2 are
not valid until after the cumulative propagation delay of two full adders (FA1 and FA2) , and so
on. At each stage ,the sum bit is not valid until after the carry bits in all the preceding stages are
valid. Carry bits must propagate or ripple through all stages before the most significant sum bit is
valid. Thus, the total sum (the parallel output) is not valid until after the cumulative delay of all
the adders.
The parallel adder in which the carry-out of each full-adder is the carry-in to the next most
significant adder is called a ripple carry adder.. The greater the number of bits that a ripple carry
adder must add, the greater the time required for it to perform a valid addition. If two numbers
are added such that no carries occur between stages, then the add time is simply the propagation
time through a single full-adder.
4- Bit Parallel Subtractor:

The subtraction of binary numbers can be carried out most conveniently by means of
complements , the subtraction A-B can be done by taking the 2‘s complement of B and adding
it to A . The 2‘s complement can be obtained by taking the 1‘s complement and adding 1 to the
least significant pair of bits. The 1‘s complement can be implemented with inverters as
Binary-Adder Subtractor:
A 4-bit adder-subtractor, the addition and subtraction operations are combined into
one circuit with one common binary adder. This is done by including an X-OR gate with each
full-adder. The mode input M controls the operation. When M=0, the circuit is an adder, and
when M=1, the circuit becomes a subtractor. Each X-OR gate receives input M and one of the
inputs of B. When M=0, .The full-adder receives the value of B , the input carry is 0
35
and the circuit performs A+B. when and C1=1. The B inputs are complemented and
a 1 is through the input carry. The circuit performs the operation A plus the 2‘s complement of B.
The Look-Ahead –Carry Adder:
In parallel-adder,the speed with which an addition can be performed is governed by

the time required for the carries to propagate or ripple through all of the stages of the adder. The
look-ahead carry adder speeds up the process by eliminating this ripple carry delay. It examines
all the input bits simultaneously and also generates the carry-in bits for all the stages
simultaneously.
The method of speeding up the addition process is based on the two additional
functions of the full-adder, called the carry generate and carry propagate functions.
Consider one full adder stage; say the nth stage of a parallel adder as shown in fig.
we know that is made by two half adders and that the half adder contains an X-OR gate to
produce the sum and an AND gate to produce the carry. If both the bits An and Bn are 1s, a carry
has to be generated in this stage regardless of whether the input carry Cin is a 0 or a 1. This is
called generated carry, expressed as Gn= An.Bn which has to appear at the output through the OR
gate as shown in fig.
Thereis another possibility of producing a carry out. X-OR gate inside the half-adder
at the input produces an intermediary sum bit- call it Pn –which is expressed as .

Next Pn and Cn are added using the X-OR gate inside the second half adder to produce the final
36
sum bit and and output carryC0= Pn.Cn=( )Cn which
becomes carry for the (n+1) thstage.
Consider the case of both Pn and Cn being 1. The input carry Cn has to be propagated
to the output only if Pn is 1. If Pn is 0, even if Cn is 1, the and gate in the second half-adder will
inhibit Cn . the carry out of the nth stage is 1 when either Gn=1 or Pn.Cn =1 or both Gn and Pn.Cn
are equal to 1.
For the final sum and carry outputs of the nth stage, we get the following Boolean
expressions.
Observe the recursive nature of the expression for the output carry
at the nth stage which becomes the input carry for the (n+1)st stage .it is possible to express the
output carry of a higher significant stage is the carry-out of the previous stage.
Based on these , the expression for the carry-outs of various full adders are as follows,
Observe that the final output carry is expressed as a function of

the input variables in SOP form. Which is two level AND-OR or equivalent NAND-NAND
form. Observe that the full look-ahead scheme requires the use of OR gate with (n+1) inputs and
AND gates with number of inputs varying from 2 to (n+1).
37
2’s complement Addition and Subtraction using Parallel Adders:
Most modern computers use the 2‘s complement system to represent negative numbers
and to perform subtraction operations of signed numbers can be performed using only the
addition operation ,if we use the 2‘s complement form to represent negative numbers.
The circuit shown can perform both addition and subtraction in the 2‘s complement. This
adder/subtractor circuit is controlled by the control signal ADD/SUB‘. When the ADD/SUB‘
level is HIGH, the circuit performs the addition of the numbers stored in registers A and B.
When the ADD/Sub‘ level is LOW, the circuit subtract the number in register B from the number
in register A. The operation is:
When ADD/SUB‘ is a 1:
1. AND gates 1,3,5 and 7 are enabled , allowing B0,B1,B2and B3 to pass to the OR gates
9,10,11,12 . AND gates 2,4,6 and 8 are disabled , blocking B0‘,B1‘,B2‘, and B3‘ from
reaching the OR gates 9,10,11 and 12.
2. The two levels B0 to B3 pass through the OR gates to the 4-bit parallel adder, to be added
to the bits A0 to A3. The sum appears at the output S0 to S3
3. Add/SUB‘ =1 causes no carry into the adder.
When ADD/SUB‘ is a 0:
1. AND gates 1,3,5 and 7 are disabled , allowing B0,B1,B2and B3 from reaching the OR gates
9,10,11,12 . AND gates 2,4,6 and 8 are enabled , blocking B0‘,B1‘,B2‘, and B3‘ from
reaching the OR gates.
38
2. The two levels B0‘ to B3‘ pass through the OR gates to the 4-bit parallel adder, to be
added to the bits A0 to A3.The C0 is now 1.thus the number in register B is converted to
its 2‘s complement form.
3. The difference appears at the output S0 toS3.

Adders/Subtractors used for adding and subtracting signed binary numbers. In computers , the
output is transferred into the register A (accumulator) so that the result of the addition or
subtraction always end up stored in the register A This is accomplished by applying a transfer
pulse to the CLK inputs of register A.
Serial Adder:
A serial adder is used to add binary numbers in serial form. The two binary numbers to be
added serially are stored in two shift registers A and B. Bits are added one pair at a time through
a single full adder (FA) circuit as shown. The carry out of the full-adder is transferred to a D flip-
flop. The output of this flip-flop is then used as the carry input for the next pair of significant
bits. The sum bit from the S output of the full-adder could be transferred to a third shift register.
By shifting the sum into A while the bits of A are shifted out, it is possible to use one register for
storing both augend and the sum bits. The serial input register B can be used to transfer a new
binary number while the addend bits are shifted out during the addition.
The operation of the serial adder is:
Initially register A holds the augend, register B holds the addend and the carry flip-flop is
cleared to 0. The outputs (SO) of A and B provide a pair of significant bits for the full-adder at x
and y. The shift control enables both registers and carry flip-flop , so, at the clock pulse both
registers are shifted once to the right, the sum bit from S enters the left most flip-flop of A , and
the output carry is transferred into flip-flop Q . The shift control enables the registers for a
number of clock pulses equal to the number of bits of the registers. For each succeeding clock
pulse a new sum bit is transferred to A, a new carry is transferred to Q, and both registers are
shifted once to the right. This process continues until the shift control is disabled. Thus the
addition is accomplished by passing each pair of bits together with the previous carry through a
single full adder circuit and transferring the sum, one bit at a time, into register A.
39
Initially, register A and the carry flip-flop are cleared to 0 and then the first number is
added from B. While B is shifted through the full adder, a second number is transferred to it
through its serial input. The second number is then added to the content of register A while a
third number is transferred serially into register B. This can be repeated to form the addition of
two, three, or more numbers and accumulate their sum in register A.
Difference between Serial and Parallel Adders:

The parallel adder registers with parallel load, whereas the serial adder uses shift
registers. The number of full adder circuits in the parallel adder is equal to the number of bits in
the binary numbers, whereas the serial adder requires only one full adder circuit and a carry flip-
flop. Excluding the registers, the parallel adder is a combinational circuit, whereas the serial
adder is a sequential circuit. The sequential circuit in the serial adder consists of a full-adder and
a flip-flop that stores the output carry.
BCD Adder:
The BCD addition process:
1. Add the 4-bit BCD code groups for each decimal digit position using ordinary binary
addition.
2. For those positions where the sum is 9 or less, the sum is in proper BCD form and no
correction is needed.
3. When the sum of two digits is greater than 9, a correction of 0110 should be added
to that sum, to produce the proper BCD result. This will produce a carry to be added
to the next decimalposition.
A BCD adder circuit must be able to operate in accordance with the above steps. In other words,
the circuit must be able to do the following:
1. Add two 4-bit BCD code groups, usingstraight binaryaddition.
40
2. Determine, if the sum of this addition is greater than 1101 (decimal 9); if it is , add
0110 (decimal 6) to this sum and generate a carry to the next decimalposition.
The first requirement is easily met by using a 4- bit binary parallel adder such as the 74LS83
IC .For example , if the two BCD code groups A3A2A1A0and B3B2B1B0 are applied to a 4-bit
parallel adder, the adder will output S4S3S2S1S0 , where S4 is actually C4 , the carry –out of the
MSB bits.
The sum outputs S4S3S2S1S0 can range anywhere from 00000 to 100109when both the
BCD code groups are 1001=9). The circuitry for a BCD adder must include the logic needed to
detect whenever the sum is greater than 01001, so that the correction can be added in. Those
cases , where the sum is greater than 1001 are listed as:
Let us define a logic output X that will go HIGH only when the sum is greater than 01001
(i.e, for the cases in table). If examine these cases ,see that X will be HIGH for either of the
following conditions:
1. Whenever S4 =1(sum greater than15)
2. Whenever S3 =1 and either S2 or S1 or both are 1 (sum 10 to 15)
This condition can be expressedas
X=S4+S3(S2+S1)
Whenever X=1, it is necessary to add the correction factor 0110 to the sum bits, and to
generate a carry. The circuit consists of three basic parts. The two BCD code groups A3A2A1A0
and B3B2B1B0 are added together in the upper 4-bit adder, to produce the sum S4S3S2S1S0. The
logic gates shown implement the expression for X. The lower 4-bit adder will add the correction
0110 to the sum bits, only when X=1, producing the final BCD sum output represented by
∑3∑2∑1∑0. The X is also the carry-out that is produced when the sum is greater than 01001.
When X=0, there is no carry and no addition of 0110. In such cases, ∑3∑2∑1∑0= S3S2S1S0.
41
Two or more BCD adders can be connected in cascade when two or more digit decimal
numbers are to be added. The carry-out of the first BCD adder is connected as the carry-in of the
second BCD adder, the carry-out of the second BCD adder is connected as the carry-in of the
third BCD adder and so on.
EXCESS-3(XS-3) ADDER:
To perform Excess-3 additions,

1. Add two xs-3 codegroups
2. If carry=1, add 0011(3) to the sum of those two codegroups
If carry =0, subtract 0011(3) i.e., add 1101 (13 in decimal) to the sum of those two code
groups.
Ex: Add 9 and 5
1100 9 in Xs-3
+1000 5 in xs-3
___ _ _ __
1 0100 there is a carry

+0011 0011 add 3 to each group
---------- ----------
0100 0111 14 in xs-3
(1) (4)
EX:
Implementation of xs-3 adder using 4-bit binary adders is shown. The augend (A3
A2A1A0) and addend (B3B2B1B0) in xs-3 are added using the 4-bit parallel adder. If the carry is a
1, then 0011(3) is added to the sum bits S3S2S1S0 of the upper adder in the lower 4-bit parallel
42
adder. If the carry is a 0, then 1101(3) is added to the sum bits (This is equivalent to subtracting
0011(3) from the sum bits. The correct sum in xs-3 is obtained
Excess-3 (XS-3) Subtractor:

To perform Excess-3 subtraction,
1. Complement thesubtrahend
2. Add the complemented subtrahend to theminuend.
3. If carry =1, result is positive. Add 3 and end around carry to the result . Ifcarry=0,
the result is negative. Subtract 3, i.e, and take the 1‘s complement of the result.
Ex: Perform 9-4

1100 9 in xs-3
+1000 Complement of 4 n Xs-3
--------
(1) 0100 There is a carry
+0011 Add 0011(3)
------------
0111
1 End around carry
------------
1000 5 in xs-3
The minuend and the 1‘s complement of the subtrahend in xs-3 are added in the upper 4-
bit parallel adder. If the carry-out from the upper adder is a 0, then 1101 is added to the sum bits
of the upper adder in the lower adder and the sum bits of the lower adder are complemented to
get the result. If the carry-out from the upper adder is a 1, then 3=0011 is added to the sum bits
of the lower adder and the sum bits of the lower adder give the result.
Binary Multipliers:
In binary multiplication by the paper and pencil method, is modified somewhat in digital
machines because a binary adder can add only two binary numbers at a time.
In a binary multiplier, instead of adding all the partial products at the end, they are added two at
a time and their sum accumulated in a register (the accumulator register). In addition, when the
multiplier bit is a 0,0s are not written down and added because it does not affect the final result.
Instead, the multiplicand is shifted left by one bit.
The multiplication of 1110 by 1001 using this processis

Multiplicand 1110
Multiplier 1001
1110 The LSB of the multiplier is a 1; write down the
multiplicand; shift the multiplicand one position to the left
(1 1 1 0 0 )
1110 The second multiplier bit is a 0; write down the previous
result 1110; shift the multiplicand to the left again (1 1 1 0
0 0)
43
+1110000 The fourth multiplier bit is a 1 write down the new
multiplicand add it to the first partial product to obtain the
final product.
1111110
This multiplication process can be performed by the serial multiplier circuit , which
multiplies two 4-bit numbers to produce an 8-bit product. The circuit consists of following
elements
X register: A 4-bit shift register that stores the multiplier --- it will shift right on the falling edge
of the clock. Note that 0s are shifted in from the left.
B register: An 8-bit register that stores the multiplicand; it will shift left on the falling edge of
the clock. Note that 0s are shifted in from the right.
A register: An 8-bit register, i.e, the accumulator that accumulates the partial products.
Adder:An 8-bit parallel adder that produces the sum of A and B registers. The adder outputs S7
through S0 are connected to the D inputs of the accumulator so that the sum can be transferred to
the accumulator only when a clock pulse gets through the AND gate.
The circuit operation can be described by going through each step in the multiplication of 1110
by 1001. The complete process requires 4 clock cycles.
1. Before the first clock pulse: Prior to the occurrence of the first clock pulse, the register A is
loaded with 00000000, the register B with the multiplicand 00001110, and the register X with
the multiplier 1001. Assume that each of these registers is loaded using its asynchronous
inputs(i.e., PRESET and CLEAR). The output of the adder will be the sum of A and B,i.e.,
00001110.
2. First Clock pulse:Since the LSB of the multiplier (X0) is a 1, the first clock pulse gets through
the AND gate and its positive going transition transfers the sum outputs into the accumulator.
The subsequent negative going transition causes the X and B registers to shift right and left,
respectively. This produces a new sum of A andB.
3. Second Clock Pulse: The second bit of the original multiplier is now in X0 . Since this bit is a 0,
the second clock pulse is inhibited from reaching the accumulator. Thus, the sum outputs are
not transferred into the accumulator and the number in the accumulator does not change. The
negative going transition of the clock pulse will again shift the X and B registers. Again a new
sum is produced.
4. Third Clock Pulse:The third bit of the original multiplier is now in X0;since this bit is a 0, the
third clock pulse is inhibited from reaching the accumulator. Thus, the sum outputs are not
transferred into the accumulator and the number in the accumulator does not change. The
negative going transition of the clock pulse will again shift the X and B registers. Again a new
sum is produced.
5. Fourth Clock Pulse: The last bit of the original multiplier is now in X0 , and since it is a 1, the
positive going transition of the fourth pulse transfers the sum into the accumulator. The
accumulator now holds the final product. The negative going transition of the clock pulse shifts
X and B again. Note that, X is now 0000, since all the multiplier bits have been shifted out.
Code converters:
The availability of a large variety of codes for the same discrete elements of
information results in the use of different codes by different digital systems. It is sometimes
necessary to use the output of one system as the input to another. A conversion circuit must be
44
inserted between the two systems if each uses different codes for the same information. Thus a
code converter is a logic circuit whose inputs are bit patterns representing numbers (or
character) in one cod and whose outputs are the corresponding representation in a different
code. Code converters are usually multiple output circuits.
To convert from binary code A to binary code B, the input lines must supply the bit
combination of elements as specified by code A and the output lines must generate the
corresponding bit combination of code B. A combinational circuit performs this transformation
by means of logic gates.
For example, a binary –to-gray code converter has four binary input lines B4, B3,B2,B1 and four
gray code output lines G4,G3,G2,G1. When the input is 0010, for instance, the output should be
0011 and so forth. To design a code converter, we use a code table treating it as a truth table to
express each output as a Boolean algebraic function of all the inputs.
In this example, of binary –to-gray code conversion, we can treat the binary to the
gray code table as four truth tables to derive expressions for G4, G3, G2, and G1. Each of these
four expressions would, in general, contain all the four input variables B4, B3,B2,and B1.
Thus,this code converter is actually equivalent to four logic circuits, one for each of the truth
tables.
The logic expression derived for the code converter can be simplified using the usual
techniques, including ‗don‘t cares‘ if present. Even if the input is an unweighted code, the same
cell numbering method which we used earlier can be used, but the cell numbers --must
correspond to the input combinations as if they were an 8-4-2-1 weighted code. s
Design of a 4-bit binary to gray code converter:
45
Design of a 4-bit gray to Binary code converter:
46
Design of a 4-bit BCD to XS-3 code converter:
47
Design of a BCD to gray code converter:
Design of a SOP circuit to Detect the Decimal numbers 5 through 12 in a 4-bit gray code
Input:
Design of a SOP circuit to detect the decimal numbers 0,2,4,6,8 in a 4-bit 5211 BCD code
input:
48
Design of a Combinational circuit to produce the 2’s complement of a 4-bit binary number:
Comparators:
49
1. Magnitude Comparator:
1- bit Magnitude Comparator:
50
4- Bit MagnitudeComparator:
51
IC Comparator:
ENCODERS:
Octal to Binary
Encoder:
Decimal to BCD Encoder:
Tristate bus system:
In digital electronicsthree-state, tri-state, or 3-statelogic allows an output port to assume a high

impedance state in addition to the 0 and 1 logic levels, effectively removing the output from the
circuit.
This allows multiple circuits to share the same output line or lines (such as a bus which cannot
listen to more than one device at a time).
Three-state outputs are implemented in many registers, bus drivers, and flip-flops in the 7400 and
4000 series as well as in other types, but also internally in many integrated circuits. Other typical
uses are internal and external buses in microprocessors, computer memory, and peripherals. Many
devices are controlled by an active-low input called OE (Output Enable) which dictates whether
the outputs should be held in a high-impedance state or drive their respective loads (to either 0- or 1-
level).
UNIT-IV
SEQUENTIAL CIRCUITS
The Basic Latch
 Basic latchis a feedback connection of two NOR gates or two NAND gates
 It can store one bit of information
It can be set to 1 using the S input and reset to 0 using the R input
The Gated Latch
 Gated latch is a basic latch that includes input gating and a control signal
 The latch retains its existing state when the control input is equal to 0
 Its state may be changed when the control signal is equal to 1. In our discussion we referred to
the control input as the clock
 We consider two types of gated latches:
 Gated SR latch uses the S and R inputs to set the latch to 1 or reset it to 0,
respectively.
 Gated D latch uses the D input to force the latch into a state that has the samelogic
value as the D input.
Gated S/R Latch
Gated D Latch
Setup and Hold Times
 Setup Time tsu
The minimum time that the input signal must be stable prior to the edge of the clock signal.
 Hold Time th
The minimum time that the input signal must be stable after the edge of the clock signal.
Flip-Flops
 A flip-flop is a storage element based on the gated latch principle
 It can have its output state changed only on the edge of the controlling clock signal
 We consider two types:

 Edge-triggered flip-flop is affected only by the input values present when theactive
edge of the clock occurs
 Master-slave flip-flop is built with two gatedlatches
 The master stage is active during half of the clock cycle, and the slave stage is active
during the other half.
 The output value of the flip-flop changes on the edge of the clock that activates the
transfer into the slave stage.
Master-Slave D Flip-Flop
A Positive-Edge-Triggered D Flip-Flop
Master-Slave D Flip-Flop with Clear and Preset
T Flip-Flop
Excitation Tables
Conversions of flip-flops
Sequential Circuit Design
• Steps in the design process for sequential circuits
• State Diagrams and State Tables Examples
• Steps in Design of a Sequential Circuit

o 1. Specification – A description of the sequential circuit. Should include a detailing of
the inputs, the outputs, and the operation. Possibly assumes that you have knowledge of
digital system basics.
o 2. Formulation: Generate a state diagram and/or a state table from the statement of the
problem.
o 3. State Assignment: From a state table assign binary codes to thestates.
o 4. Flip-flop Input Equation Generation: Select the type of flip-flop for the circuit and generate
the needed input for the required state transitions
o 5. Output Equation Generation: Derive output logic equations for generation of the
output from the inputs and current state.
o 6. Optimization: Optimize the input and output equations. Today, CAD systems are
typically used for this in real systems.
o 7. Technology Mapping: Generate a logic diagram of the circuit using ANDs, ORs,
Inverters, and F/Fs.
o 8. Verification: Use a HDL to verify the design
Registers and Counters

• An n-bit register is a cascade of n flip-flops and can store an n-bit binary data
• A counter can count occurrences of events and can generate timing intervals for control purposes
A Simple Shift Register
Parallel-Access Shift Register
Counters
• Counters are a specific type of sequential circuit.
• Like registers, the state, or the flip-flop values themselves, serves as the “output.”
• The output value increases by one on each clock cycle.
• After the largest value, the output “wraps around” back to 0.
• Using two bits, we’d get something like this:

Present State Next State
A B A B
0 0 0 1
0 1 1 0
1 0 1 1
1 1 0 0
Benefits of counters
• Counters can act as simple clocks to keep track of “time.” •
You may need to record how many times something has
happened.
– How many bits have been sent or received?
– How many steps have been performed in some computation?
• All processors contain a program counter, or PC.
– Programs consist of a list of instructions that are to be executed one after another (for the
most part).
– The PC keeps track of the instruction currently being executed.
– The PC increments once on each clock cycle, and the next program instruction is then
executed.
A Three-Bit Up-Counter
Q1 is connected to clk, Q2 and Q3 are clocked by Q’ of the preceding stage (hence called
asynchronous or ripple counter
A Three-Bit Down-Counter
Shift registers:
In digital circuits, a shift register is a cascade of flip-flops sharing the same clock, in
which the output of each flip-flop is connected to the "data" input of the next flip-flop in the
chain, resulting in a circuit that shifts by one position the "bit array" stored in it, shifting in the
data present at its input and shifting out the last bit in the array, at each transition of the clock
input. More generally, a shift register may be multidimensional, such that its "data in" and stage
outputs are themselves bit arrays: this is implemented simply by running several shift registers of
the same bit-length in parallel.
Shift registers can have both parallel and serial inputs and outputs. These are often configured
as serial-in, parallel-out (SIPO) or as parallel-in, serial-out (PISO). There are also types that
have both serial and parallel input and types with serial and parallel output. There are also bi-
directional shift registers which allow shifting in both directions: L→R or R→L. The serial
input and last output of a shift register can also be connected to create a circular shift register
Shift registers are a type of logic circuits closely related to counters. They are basically for the
storage and transfer of digital data.
Buffer register:
The buffer register is the simple set of registers. It is simply stores the binary word. The buffer
may be controlled buffer. Most of the buffer registers used D Flip-flops.
Figure: logic diagram of 4-bit buffer register

The figure shows a 4-bit buffer register. The binary word to be stored is applied to the data
terminals. On the application of clock pulse, the output word becomes the same as the word
applied at the terminals. i.e., the input word is loaded into the register by the application of clock
pulse.
When the positive clock edge arrives, the stored word becomes:
Q4Q3Q2Q1=X4X3X2X1
Q=X
Controlled buffer register:
If goes LOW, all the FFs are RESET and the output becomes, Q=0000.
When is HIGH, the register is ready for action. LOAD is the control input. When
LOAD is HIGH, the data bits X can reach the D inputs of FF‘s.
Q4Q3Q2Q1=X4X3X2X1
Q=X
When load is low, the X bits cannot reach the FF‘s.
Data transmission in shift registers:
A number of ff‘s connected together such that data may be shifted into and shifted out of them is
called shift register. data may be shifted into or out of the register in serial form or in parallel
form. There are four basic types of shift registers.
1. Serial in, serial out, shift right, shift registers
2. Serial in, serial out, shift left, shift registers
3. Parallel in, serial out shift registers
4. Parallel in, parallel out shift registers
Serial IN, serial OUT, shift right, shift left register:
The logic diagram of 4-bit serial in serial out, right shift register with four stages. The register
can store four bits of data. Serial data is applied at the input D of the first FF. the Q output of the
first FF is connected to the D input of another FF. the data is outputted from the Q terminal of
the last FF.
When serial data is transferred into a register, each new bit is clocked into the first FF at the
positive going edge of each clock pulse. The bit that was previously stored by the first FF is
transferred to the second FF. the bit that was stored by the Second FF is transferred to the third
FF.
Serial-in, parallel-out, shift register:
In this type of register, the data bits are entered into the register serially, but the data stored in
the register is shifted out in parallel form.
Once the data bits are stored, each bit appears on its respective output line and all bits are
available simultaneously, rather than on a bit-by-bit basis with the serial output. The serial-in,
parallel out, shift register can be used as serial-in, serial out, shift register if the output is taken
from the Q terminal of the last FF.
Parallel-in, serial-out, shift register:
For a parallel-in, serial out, shift register, the data bits are entered simultaneously into their
respective stages on parallel lines, rather than on a bit-by-bit basis on one line as with serial data
bits are transferred out of the register serially. On a bit-by-bit basis over a single line.
There are four data lines A,B,C,D through which the data is entered into the register in
parallel form. The signal shift/ load allows the data to be entered in parallel form into the register
and the data is shifted out serially from terminalQ4
Parallel-in, parallel-out, shift register
In a parallel-in, parallel-out shift register, the data is entered into the register in parallel form,
and also the data is taken out of the register in parallel form. Data is applied to the D input
terminals of the FF‘s. When a clock pulse is applied, at the positive going edge of the pulse, the
D inputs are shifted into the Q outputs of the FFs. The register now stores the data. The stored
data is available instantaneously for shifting out in parallel form.
Bidirectional shift register:
A bidirectional shift register is one which the data bits can be shifted from left to right
or from right to left. A fig shows the logic diagram of a 4-bit serial-in, serial out, bidirectional
shift register. Right/left is the mode signal, when right /left is a 1, the logic circuit works as a
shift-register.the bidirectional operation is achieved by using the mode signal and two NAND
gates and one OR gate for each stage.
A HIGH on the right/left control input enables the AND gates G1, G2, G3 and G4 and
disables the AND gates G5,G6,G7 and G8, and the state of Q output of each FF is passed
through the gate to the D input of the following FF. when a clock pulse occurs, the data bits are
then effectively shifted one place to the right. A LOW on the right/left control inputs enables the
AND gates G5, G6, G7 and G8 and disables the And gates G1, G2, G3 and G4 and the Q output
of each FF is passed to the D input of the preceding FF. when a clock pulse occurs, the data bits
are then effectively shifted one place to the left. Hence, the circuit works as a bidirectional shift
register
Figure: logic diagram of a 4-bit bidirectional shift register
Universal shift register:
A register is capable of shifting in one direction only is a unidirectional shift register. One that
can shift both directions is a bidirectional shift register. If the register has both shifts and parallel
load capabilities, it is referred to as a universal shift registers. Universal shift register is a
bidirectional register, whose input can be either in serial form or in parallel form and whose
output also can be in serial form or I parallel form.
The most general shift register has the following capabilities.
1. A clear control to clear the register to 0

2. A clock input to synchronize the operations
3. A shift-right control to enable the shift-right operation and serial input and output lines
associated with the shift-right
4. A shift-left control to enable the shift-left operation and serial input and output lines
associated with the shift-left
5. A parallel loads control to enable a parallel transfer and the n input lines associated with
the parallel transfer
6. N parallel output lines
7. A control state that leaves the information in the register unchanged in the presence of
the clock.
A universal shift register can be realized using multiplexers. The below fig shows the logic
diagram of a 4-bit universal shift register that has all capabilities. It consists of 4 D flip-flops and
four multiplexers. The four multiplexers have two common selection inputs s1 and s0. Input 0 in
each multiplexer is selected when S1S0=00, input 1 is selected when S1S0=01 and input 2 is
selected when S1S0=10 and input 4 is selected when S1S0=11. The selection inputs control the
mode of operation of the register according to the functions entries. When S1S0=0, the present
value of the register is applied to the D inputs of flip-flops. The condition forms a path from the
output of each flip-flop into the input of the same flip-flop. The next clock edge transfers into
each flip-flop the binary value it held previously, and no change of state occurs. When S1S0=01,
terminal 1 of the multiplexer inputs have a path to the D inputs of the flip-flop. This causes a
shift-right operation, with serial input transferred into flip-flopA4. When S1S0=10, a shift left
operation results with the other serial input going into flip-flop A1. Finally when S1S0=11, the
binary information on the parallel input lines is transferred into the register simultaneously
during the next clock cycle
Figure: logic diagram 4-bit universal shift register

Function table for theregister
mode control
S0 S1 register operation
0 0 No change
0 1 Shift Right
1 0 Shift left
1 1 Parallel load
Counters:
Counter is a device which stores (and sometimes displays) the number of times
particular event or process has occurred, often in relationship to a clock signal. A Digital counter
is a set of flip flops whose state change in response to pulses applied at the input to the counter.
Counters may be asynchronous counters or synchronous counters. Asynchronous counters are
also called ripple counters
In electronics counters can be implemented quite easily using register-type circuits such as
the flip-flops and a wide variety of classifications exist:
• Asynchronous (ripple) counter – changing state bits are used as clocks to subsequent state
flip-flops
• Synchronous counter – all state bits change under control of a singleclock
• Decade counter – counts through ten states per stage
• Up/down counter – counts both up and down, under command of a control input
• Ring counter – formed by a shift register with feedback connection in a ring
• Johnson counter – a twisted ring counter
Cascaded counter
Modulus counter.
Each is useful for different applications. Usually, counter circuits are digital in nature, and count
in natural binary Many types of counter circuits are available as digital building blocks, for
example a number of chips in the 4000 series implement different counters.
Occasionally there are advantages to using a counting sequence other than the natural binary
sequence such as the binary coded decimal counter, a linear feed-back shift register counter, or
a gray-code counter.
Counters are useful for digital clocks and timers, and in oven timers, VCR clocks, etc.
Asynchronous counters:
An asynchronous (ripple) counter is a single JK-type flip-flop, with its J (data) input fed
from its own inverted output. This circuit can store one bit, and hence can count from zero to one
before it overflows (starts over from 0). This counter will increment once for every clock cycle
and takes two clock cycles to overflow, so every cycle it will alternate between a transition from
0 to 1 and a transition from 1 to 0. Notice that this creates a new clock with a 50% duty cycle at
exactly half the frequency of the input clock. If this output is then used as the clock signal for a
similarly arranged D flip-flop (remembering to invert the output to the input), one will get
another 1 bit counter that counts half as fast. Putting them together yields a two-bit counter:
Two-bit ripple up-counter using negative edge triggered flip flop:
Two bit ripple counter used two flip-flops. There are four possible states from 2 – bit up-
counting I.e. 00, 01, 10 and 11.
· The counter is initially assumed to be at a state 00 where the outputs of the tow flip-flops
are noted as Q1Q0. Where Q1 forms the MSB and Q0 forms the LSB.
· For the negative edge of the first clock pulse, output of the first flip-flop FF1 toggles its
state. Thus Q1 remains at 0 and Q0 toggles to 1 and the counter state are now read as 01.
· During the next negative edge of the input clock pulse FF1 toggles and Q0 = 0. The output
Q0 being a clock signal for the second flip-flop FF2 and the present transition acts as a negative
edge for FF2 thus toggles its state Q1 = 1. The counter state is now read as 10.
· For the next negative edge of the input clock to FF1 output Q0 toggles to 1. But this
transition from 0 to 1 being a positive edge for FF2 output Q1 remains at 1. The counter state is
now read as 11.
· For the next negative edge of the input clock, Q0 toggles to 0. This transition from 1 to 0
acts as a negative edge clock for FF2 and its output Q1 toggles to 0. Thus the starting state 00 is
attained. Figure shown below
Two-bit ripple down-counter using negative edge triggered flip flop:
A 2-bit down-counter counts in the order 0,3,2,1,0,1…….,i.e, 00,11,10,01,00,11 …..,etc. the

above fig. shows ripple down counter, using negative edge triggered J-K FFs and its timing
diagram.
• For down counting, Q1‘ of FF1 is connected to the clock of Ff2. Let initially all the FF1
toggles, so, Q1 goes from a 0 to a 1 and Q1‘ goes from a 1 to a 0.
• The negative-going signal at Q1‘ is applied to the clock input of FF2, toggles Ff2 and,
therefore, Q2 goes from a 0 to a 1.so, after one clock pulse Q2=1 and Q1=1, I.e., the state
of the counter is 11.
• At the negative-going edge of the second clock pulse, Q1 changes from a 1 to a 0 and
Q1‘ from a 0 to a 1.
• This positive-going signal at Q1‘ does not affect FF2 and, therefore, Q2 remains at a 1.
Hence , the state of the counter after second clock pulse is 10
• At the negative going edge of the third clock pulse, FF1 toggles. So Q1, goes from a 0 to
a 1 and Q1‘ from 1 to 0. This negative going signal at Q1‘ toggles FF2 and, so, Q2
changes from 1 to 0, hence, the state of the counter after the third clock pulse is 01.
• At the negative going edge of the fourth clock pulse, FF1 toggles. So Q1, goes from a 1
to a 0 and Q1‘ from 0 to 1. . This positive going signal at Q1‘ does not affect FF2 and, so,
Q2 remains at 0, hence, the state of the counter after the fourth clock pulse is 00.
Two-bit ripple up-down counter using negative edge triggered flip flop:
Figure: asynchronous 2-bit ripple up-down counter using negative edge triggered flip flop:
• As the name indicates an up-down counter is a counter which can count both in upward
and downward directions. An up-down counter is also called a forward/backward counter
or a bidirectional counter. So, a control signal or a mode signal M is required to choose
the direction of count. When M=1 for up counting, Q1 is transmitted to clock of FF2 and
when M=0 for down counting, Q1‘ is transmitted to clock of FF2. This is achieved by
using two AND gates and one OR gates. The external clock signal is applied to FF1.
• Clock signal to FF2= (Q1.Up)+(Q1‘. Down)= Q1m+Q1‘M‘
Design of Asynchronous counters:
To design a asynchronous counter, first we write the sequence , then tabulate the values of
reset signal R for various states of the counter and obtain the minimal expression for R and R‘
using K-Map or any other method. Provide a feedback such that R and R‘ resets all the FF‘s after
the desired count
Design of a Mod-6 asynchronous counter using T FFs:
A mod-6 counter has six stable states 000, 001, 010, 011, 100, and 101. When the sixth
clock pulse is applied, the counter temporarily goes to 110 state, but immediately resets to 000
because of the feedback provided. it is ―divide by-6-counter‖, in the sense that it divides the
input clock frequency by 6.it requires three FFs, because the smallest value of n satisfying the
conditionN≤2n is n=3; three FFs can have 8 possible states, out of which only six are utilized and
the remaining two states 110and 111, are invalid. If initially the counter is in 000 state, then after
the sixth clock pulse, it goes to 001, after the second clock pulse, it goes to 010, and so on.
After sixth clock pulse it goes to 000. For the design, write the truth table with present state
outputs Q3, Q2 and Q1 as the variables, and reset R as the output and obtain an expression for R
in terms of Q3, Q2, and Q1that decides the feedback into be provided. From the truth table,
R=Q3Q2. For active-low Reset, R‘ is used. The reset pulse is of very short duration, of the order
of nanoseconds and it is equal to the propagation delay time of the NAND gate used. The
expression for R can also be determined as follows.
R=0 for 000 to 101, R=1 for 110, and R=X=for111

Therefore,
R=Q3Q2Q1‘+Q3Q2Q1=Q3Q2
The logic diagram and timing diagram of Mod-6 counter is shown in the above fig.
The truth table is as shown in below.

After States
pulses Q3 Q2 Q1 R
0 0 0 0 0
1 0 0 1 0
2 0 1 0 0
3 0 1 1 0
4 1 0 0 0
5 1 0 1 0
6 1 1 0 1
0 0 0 0
7 0 0 0 0
Design of a mod-10 asynchronous counter using T-flip-flops:

A mod-10 counter is a decade counter. It also called a BCD counter or a divide-by-10
counter. It requires four flip-flops (condition 10 ≤2n is n=4). So, there are 16 possible states, out
of which ten are valid and remaining six are invalid. The counter has ten stable state, 0000
through 1001, i.e., it counts from 0 to 9. The initial state is 0000 and after nine clock pulses it
goes to 1001. When the tenth clock pulse is applied, the counter goes to state 1010 temporarily,
but because of the feedback provided, it resets to initial state 0000. So, there will be a glitch in
the waveform of Q2. The state 1010 is a temporary state for which the reset signal R=1, R=0 for
0000 to 1001, and R=C for 1011 to 1111.
The count table and the K-Map for reset are shown in fig. from the K-Map R=Q4Q2. So,
feedback is provided from second and fourth FFs. For active –HIGH reset, Q4Q2 is applied to
the clear terminal. For active-LOW reset 4 2 is connected isof all Flip=flops.
After Count
pulses Q4 Q3 Q2 Q1
0 0 0 0 0
1 0 0 0 1
2 0 0 1 0
3 0 0 1 1
4 0 1 0 0
5 0 0 0 1
6 0 1 1 0
7 0 1 1 1
8 1 0 0 0
9 0 1 0 1
10 0 0 0 0
Synchronous counters:
Asynchronous counters are serial counters. They are slow because each FF can change state
only if all the preceding FFs have changed their state. if the clock frequency is very high, the
asynchronous counter may skip some of the states. This problem is overcome in synchronous
counters or parallel counters. Synchronous counters are counters in which all the flip flops are
triggered simultaneously by the clock pulses Synchronous counters have a common clock pulse
applied simultaneously to all flip- -Bit Synchronous Binary Counter
Design of synchronous counters:
For a systematic design of synchronous counters. The following procedure is used.
Step 1:State Diagram: draw the state diagram showing all the possible states state diagram which
also be called nth transition diagrams, is a graphical means of depicting the sequence of states
through which the counter progresses.
Step2: number of flip-flops: based on the description of the problem, determine the required
number n of the flip-flops- the smallest value of n is such that the number of states N≤2n--- and
the desired counting sequence.
Step3: choice of flip-flops excitation table: select the type of flip-flop to be used and write the
excitation table. An excitation table is a table that lists the present state (ps) , the next state(ns)
and required excitations.
Step4: minimal expressions for excitations: obtain the minimal expressions for the excitations of
the FF using K-maps drawn for the excitation of the flip-flops in terms of the present states and
inputs.
Step5: logic diagram: draw a logic diagram based on the minimal expressions
Design of a synchronous 3-bit up-down counter using JK flip-flops:
Step1: determine the number of flip-flops required. A 3-bit counter requires three FFs. It has 8
states (000,001,010,011,101,110,111) and all the states are valid. Hence no don‘t cares. For
selecting up and down modes, a control or mode signal M is required. When the mode signal
M=1 and counts down when M=0. The clock signal is applied to all the FFs simultaneously.
Step2: draw the state diagrams: the state diagram of the 3-bit up-down counter is drawn as
Step3: select the type of flip flop and draw the excitation table: JK flip-flops are selected and the
excitation table of a 3-bit up-down counter using JK flip-flops is drawn as shown in fig.
PS mode NS required excitations

Q3 Q2 Q1 M Q3 Q2 Q1 J3 K3 J2 K2 J1 K1
0 0 0 0 1 1 1 1 x 1 x 1 x
0 0 0 1 0 0 1 0 x 0 x 1 x
0 0 1 0 0 0 0 0 x 0 x x 1
0 0 1 1 0 1 0 0 x 1 x x 1
0 1 0 0 0 0 1 0 x x 1 1 x
0 1 0 1 0 1 1 0 x x 0 1 x
0 1 1 0 0 1 0 0 x x 0 x 1
0 1 1 1 1 0 0 1 x x 1 x 1
1 0 0 0 0 1 1 x 1 1 x 1 x
1 0 0 1 1 0 1 x 0 0 x 1 x
1 0 1 0 1 0 0 x 0 0 x x 1
1 0 1 1 1 1 0 x 0 1 x x 1
1 1 0 0 1 0 1 x 0 x 1 1 x
1 1 0 1 1 1 1 x 0 x 0 1 x
1 1 1 0 1 1 0 x 0 x 0 x 1
1 1 1 1 0 0 0 x 1 x 1 x 1
Step4: obtain the minimal expressions: From the excitation table we can conclude that J1=1 and
K1=1, because all the entries for J1and K1 are either X or 1. The K-maps for J3, K3,J2 and K2
based on the excitation table and the minimal expression obtained from them are shown in fig.
00 01 11 10
Q3Q2 Q1M
1
1
X X X X
X X X X
Step5: draw the logic diagram: a logic diagram using those minimal expressions can be drawn as
shown in fig.
Design of a synchronous modulo-6 gray cod counter:
Step 1: the number of flip-flops: we know that the counting sequence for a modulo-6 gray code
counter is 000, 001, 011, 010, 110, and 111. It requires n=3FFs (N≤2n, i.e., 6≤23). 3 FFs can have
8 states. So the remaining two states 101 and 100 are invalid. The entries for excitation
corresponding to invalid states are don‘t cares.
Step2: the state diagram: the state diagram of the mod-6 gray code converter is drawn as shown
in fig.
Step3: type of flip-flop and the excitation table: T flip-flops are selected and the excitation table
of the mod-6 gray code counter using T-flip-flops is written as shown in fig.
required
PS NS excitations
Q3 Q2 Q1 Q3 Q2 Q1 T3 T2 T1
0 0 0 0 0 1 0 0 1
0 0 1 0 1 1 0 1 0
0 1 1 0 1 0 0 0 1
0 1 0 1 1 0 1 0 0
1 1 0 1 1 1 0 0 1
1 1 1 0 0 0 1 1 1
Step4: The minimal expressions: the K-maps for excitations of FFs T3,T2,and T1 in terms of
outputs of FFs Q3,Q2, and Q1, their minimization and the minimal expressions for excitations
obtained from them are shown if fig
Step5: the logic diagram: the logic diagram based on those minimal expressions is drawn as
shown in fig.
Design of a synchronous BCD Up-Down counter using FFs:
Step1: the number of flip-flops: a BCD counter is a mod-10 counter has 10 states (0000 through
1001) and so it requires n=4FFs(N≤2n,, i.e., 10≤24). 4 FFS can have 16 states. So out of 16 states,
six states (1010 through 1111) are invalid. For selecting up and down mode, a control or mode
signal M is required. , it counts up when M=1 and counts down when M=0. The clock signal is
applied to all FFs.
Step2: the state diagram: The state diagram of the mod-10 up-down counter is drawn as shown
in fig.
Step3: types of flip-flops and excitation table: T flip-flops are selected and the excitation table of
the modulo-10 up down counter using T flip-flops is drawn as shown in fig.
The remaining minterms are don‘t cares(∑d(20,21,22,23,24,25,26,37,28,29,30,31)) from

the excitation table we can see that T1=1 and the expression for T4,T3,T2 are asfollows.
T4=∑m(0,15,16,19)+d(20,21,22,23,24,25,26,27,28,29,30,31)
T3=∑m(7,15,16,8)+d(20,21,22,23,24,25,26,27,28,29,30,31)
T2=∑m(3,4,7,8,11,12,15,16)+d(20,21,22,23,24,25,26,27,28,29,30,31)
PS NS
mode required excitations

Q4 Q3 Q2 Q1 M Q4 Q3 Q2 Q1 T4 T3 T2 T1
0 0 0 0 0 1 0 0 1 1 0 0 1
0 0 0 0 1 0 0 0 1 0 0 0 1
0 0 0 1 0 0 0 0 0 0 0 0 1
0 0 0 1 1 0 0 1 0 0 0 1 1
0 0 1 0 0 0 0 0 1 0 0 1 1
0 0 1 0 1 0 0 1 1 0 0 0 1
0 0 1 1 0 0 0 1 0 0 0 0 1
0 0 1 1 1 0 1 0 0 0 1 1 1
0 1 0 0 0 0 0 1 1 0 1 1 1
0 1 0 0 1 0 1 0 1 0 0 0 1
0 1 0 1 0 0 1 0 0 0 0 0 1
0 1 0 1 1 0 1 1 0 0 0 1 1
0 1 1 0 0 0 1 0 1 0 0 1 1
0 1 1 0 1 0 1 1 1 0 0 0 1
0 1 1 1 0 0 1 1 0 0 0 0 1
0 1 1 1 1 1 0 0 0 1 1 1 1
1 0 0 0 0 0 1 1 1 1 1 1 1
1 0 0 0 1 1 0 0 1 0 0 0 1
1 0 0 1 0 1 0 0 0 0 0 0 1
1 0 0 1 1 0 0 0 0 1 0 0 1
Step4: The minimal expression: since there are 4 state variables and a mode signal, we require 5
variable kmaps. 20 conditions of Q4Q3Q2Q1M are valid and the remaining 12 combinations are
invalid. So the entries for excitations corresponding to those invalid combinations are don‘t
cares. Minimizing K-maps for T2 we get
T 2= Q4Q1‘M+Q4‘Q1M+Q2Q1‘M‘+Q3Q1‘M‘
Step5: the logic diagram: the logic diagram based on the above equation is shown in fig.
Shift register counters:

One of the applications of shift register is that they can be arranged to form several types of
counters. The most widely used shift register counter is ring counter as well as the twisted ring
counter.
Ring counter: this is the simplest shift register counter. The basic ring counter using D flip-
flops is shown in fig. the realization of this counter using JK FFs. The Q output of each stage is
connected to the D flip-flop connected back to the ring counter.
FIGURE: logic diagram of 4-bit ring counter using D flip-flops
Only a single 1 is in the register and is made to circulate around the register as long as clock
pulses are applied. Initially the first FF is present to a 1. So, the initial state is 1000, i.e., Q1=1,
Q2=0,Q3=0,Q4=0. After each clock pulse, the contents of the register are shifted to the right by
one bit and Q4 is shifted back to Q1. The sequence repeats after four clock pulses. The number
of distinct states in the ring counter, i.e., the mod of the ring counter is equal to number of FFs
used in the counter. An n-bit ring counter can count only n bits, where as n-bit ripple counter can
count 2n bits. So, the ring counter is uneconomical compared to a ripple counter but has
advantage of requiring no decoder, since we can read the count by simply noting which FF is set.
Since it is entirely a synchronous operation and requires no gates external FFs, it has the further
advantage of being very fast.
Timing diagram:
Twisted Ring counter (Johnson counter):
This counter is obtained from a serial-in, serial-out shift register by providing feedback
from the inverted output of the last FF to the D input of the first FF. the Q output of each is
connected to the D input of the next stage, but the Q‘ output of the last stage is connected to the
D input of the first stage, therefore, the name twisted ring counter. This feedback arrangement
produces a unique sequence of states.
The logic diagram of a 4-bit Johnson counter using D FF is shown in fig. the realization
of the same using J-K FFs is shown in fig.. The state diagram and the sequence table are shown
in figure. The timing diagram of a Johnson counter is shown in figure.
Let initially all the FFs be reset, i.e., the state of the counter be 0000. After each clock
pulse, the level of Q1 is shifted to Q2, the level of Q2to Q3, Q3 to Q4 and the level of Q4‘to Q1
and the sequences given in fig.
Figure: Johnson counter with JK flip-flops
Figure: timing diagram

UNIT- V
MEMORY
Memory structures are crucial in digital design. – ROM, PROM, EPROM, RAM, SRAM, (S)DRAM,
RDRAM,..
➢ All memory structures have an address bus and a data bus – Possibly other control signals to control
output etc. •E.g. 4 Bit Address bus with 5 Bit Data Bus ADDR DOUT
There are two types of memories that are used in digital systems:
o Random-access memory(RAM): perform both the write and

read operations.
o Read-only memory(ROM): perform only the read operation.
The read-only memory is a programmable logic device. Other such units are the programmablelogic
array(PLA), the programmable array logic(PAL), and the field-programmable gatearray(FPGA).
Random-Access Memory:
A memory unit stores binary information in groups of bits called words.
• byte = 8 bits
• word = 2 bytes
The communication between a memory and its environment is achieved through data input andoutput
lines, address selection lines, and control lines that specify the direction oftransfer.
In random-access memory, the word locations may be thought of as being separated in space, with
each word occupying one particular location.
In sequential-access memory, the information stored in some medium is not immediately accessible,
but is available only certain intervals of time. A magnetic disk or tape unit is of this type.
In a random-access memory, the access time is always the same regardless of the particular locationof
the word.
In a sequential-access memory, the time it takes to access a word depends on the position of the word
with respect to the reading head position; therefore, theaccess time is variable.
Static RAM
SRAM consists essentially of internal latches that store the binaryinformation.
The stored information remains valid as long as power is applied to the unit.
SRAM is easier to use and has shorter read and write cycles.
Low density, low capacity, high cost, high speed, high power consumption.
Dynamic RAM
DRAM stores the binary information in the form of electric charges oncapacitors.
The capacitors are provided inside the chip by MOS transistors.
The capacitors tends to discharge with time and must be periodically recharged by refreshing the
dynamic memory.
DRAM offers reduced power consumption and larger storage capacity in a single memorychip.
High density, high capacity, low cost, low speed, low power consumption.
Memory decoding
The equivalent logic of a binary cell that stores one bit of information is shown below.
▪ Read/Write = 0, select = 1, input data to S-R latch

▪ Read/Write = 1, select = 1, output data from S-R latch
Programmable Logic Array:
The decoder in PROM is replaced by an array of AND gates that can be programmed to
generate any product term of the input variables.
The product terms are then connected to OR gates to provide the sum of products forthe
required Boolean functions.
➢ The output is inverted when the XOR input is connected to 1 (since x⊕1 = x’). The output
doesn’t change and connect to 0 (since x⊕0 = x).
F1 =
AB’+AC+A’BC’
F2 = (AC+BC)’
Implement the following two Boolean functions with a PLA:
• F1(A, B, C) = ∑(0, 1, 2, 4)
• F2(A, B, C) = ∑(0, 5, 6, 7)

Digital Logic Design (R17a0461) (1) - 7-130

Uploaded by

Copyright:

Available Formats

Digital Logic Design (R17a0461) (1) - 7-130

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Digital Logic Design (R17a0461) (1) - 7-130

Uploaded by

Copyright:

Available Formats

NUMBER SYSTEM

i) Octal number systems

ii) Hexa Decimal number system

iii) Binary Coded Decimal number(BCD) system

To define any number system we have to specify

• Base of the number system such as 2,8,10 or 16.

Binary number system:

DIGITAL LOGIC DESIGN Page no. 3

Decimal Number system

Octal Number System

Hexa Decimal Number System

Decima Binar Octal Hexadeci

DIGITAL LOGIC DESIGN Page no. 4

i) Binary to octal number conversion

iii) Octal to binary Conversion

iv) Hexa to binary conversion

v) Octal to Decimal conversion

Ex: convert 4057.068 to octal

DIGITAL LOGIC DESIGN Page no. 5

Ex: convert 378.9310 to octal

37810 to octal: Successive division:

=(5x162)+(C x161)+ (7 x160)

DIGITAL LOGIC DESIGN Page no. 6

ix) Octal to hexadecimal conversion:

x) Hexadecimal to octal conversion:

i) The radix complement or r’s complement

DIGITAL LOGIC DESIGN Page no. 7

• Two ways of rep signed no.s

Representation of signed no.s using 2’s or 1’s complement method:

DIGITAL LOGIC DESIGN Page no. 8

Characteristics of 2’s compliment no.s:

Signed binary numbers:

DIGITAL LOGIC DESIGN Page no. 9

+45 in 8 bit form is 00101101

11010011 is 2‘s comp form

Subtract the given no. N from 2n

11010011 is 2‘s comp

Original no: 00101101

DIGITAL LOGIC DESIGN Page no. 10

10110110.0100 is 2‘s comp

Ex:Subtract 14 from 46 using 8 bit 2‘s comp arithmetic:

DIGITAL LOGIC DESIGN Page no. 11

EX: Add -75 to +26 using 8 bit 2‘s comp arithmetic

-49 11001111 No carry

Ex: add -45.75 to +87.5 using 12 bit arithmetic

-41.75 (1)00101001.1100 ignore carry

1’s compliment of n number:

+11 (1)00001010 -11 11110100

DIGITAL LOGIC DESIGN Page no. 13

Non weighted codes

DIGITAL LOGIC DESIGN Page no. 14

Gray Code MSB is binary code MSB.

8421 BCD code ( Natural BCD code):

But as 0001 0100 in 8421 ode.

It is individually adding the corresponding digits of the decimal no,s expressed in

Ex: Perform decimal additions in 8421 code

DIGITAL LOGIC DESIGN Page no. 15

(1)0001 (1)0000 (1)0101 . (1)0100 propagate carry