Electrical Specification MZ & Partners Doha Port Redevelopment Project GP18182

CABLE TRAYS
SECTION 16139

PART 1 - GENERAL

0.1 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including Conditions of Contract and
Division 1 Specification Sections, apply to this Section.

0.2 SUMMARY

A. This Section includes cable trays, cable ladders and related installations and accessories
necessary to support and protect cables, feeders, sub-feeders, branch circuit wiring and
wiring of low current systems, communications and signal cables.

B. Related Sections include the following:

1.Division 16 Section "Basic Electrical Materials and Methods" for cable tray / ladder
supports not specified in this Section.

0.3 SUBMITTALS

A. Technical Data: Submit data for approval including, but not limited to, the following:

1.Manufacturers' catalogues with specifications of cable trays / ladders and related

accessories.
2. Samples of each type of tray / ladder and accessory.

B. Shop and Construction Drawings: Submit drawings for approval including, but not limited
to, the following:

1.Detail fabrication and installation of cable tray / ladder, including plans, elevations, and
sections of components and attachments to other construction elements. Designate
components and accessories, including clamps, brackets, hanger rods, splice-plate
connectors, expansion-joint assemblies, straight lengths, fittings and earthing
connections.

C. Coordination Drawings: Include floor plans and sections drawn to scale. Include scaled
cable tray / ladder layout and relationships between components and adjacent structural
and mechanical elements.

D. Design Calculations: Verify loading capacities for supports, and Cable Tray Sizes.

E. Maintenance Data: For cable trays to include in the maintenance manuals specified in
Division 1

0.4 QUALITY ASSURANCE

A. Source Limitations: Obtain cable tray components through one source from a single
manufacturer.

B. Comply with related BS Standards.

1.5 COORDINATION

A. Coordinate layout and installation of cable tray / ladder with other installations.

CABLE TRAYS September 2018 16139-1

Electrical Specification MZ & Partners Doha Port Redevelopment Project GP18182

1. Revise locations and elevations from those indicated as required to suit field conditions
and as approved by the Engineer.

PART 2 - PRODUCTS

0.1 MANUFACTURERS

A. Refer to Section 16999 Lists of Approved and Recommended Manufacturers.

0.2 CABLE TRAYS AND LADDERS (HOT DIPPED GALVANIZED)

A. Components: To include cable trays or ladders (as shown on the Drawings), bends, elbows,
tees, couplings and plates, rubber grommets, hangers, bracket supports and other system
accessories required for safety and protection of the cable installations.

B. Trays: Provide to carry the maximum load of cables with a factor of safety 300%.

C. Trays: Heavy gauge perforated sheet steel, hot-dip galvanized after manufacture, minimum
1.5 mm thick, with sides not less than 45 mm deep, and as shown on drawings. Fittings
are to be same material as tray.

D. Ladders: to be hot-dip galvanized after manufacture, fabricated from 2mm mild carbon
steel. Ladder side channels are to be minimum 127 x 32 mm, strengthened by reinforcing
inserts for torsional rigidity. Rungs are to be slotted to take cable cleats or ties and conduit
clamps. Rungs are to be minimum 50 x 25 mm channels, spaced at 300 mm centers.

E. Galvanizing to be in accordance with BS 729 (335 g/m²), applied after fabrication.

F. Bolts and Screws: Cadmium plated or electrolytically galvanized.

G. Coating applied to cable tray or cable ladder is to be applied after priming coat.

H. Sizes: Trays and ladders are to be standard metric sizes, 300, 450, 600, 750 & 900 mm
wide, and at least 2.4 m length of section. Size of tray or ladder is to be determined by
number and sizes of cables in accordance with the Regulations and / or as shown on the
Drawings. Tray or ladder is to have strength and rigidity to provide support for cables
contained within. Deflection between supports is not to exceed 1/350 under full loading
capacity.

I. Earthing connector for plastic coated trays or ladders is to be provided on each coupling
between adjacent sections.

J. Cable Tray Cover : Provide cable tray cover for all installation at exposed areas.

K. Cable Trays / Ladder serving Life Safety equipment shall be fire rated for at least 2 hours or
as shown on drawings.

PART 3 - EXECUTION

0.1 INSTALLATION

A. Install cable tray / ladder level and plumb according to manufacturer's written instructions,
Coordination Drawings, original design, and referenced standards.

B. Each run is to be completed before installation of cables.

C. Remove burrs and sharp edges from cable trays / ladders. Fix trays / ladders using
approved suspension rods or steel angle brackets at spacing not exceeding 1.5 m and
generally as shown on the Drawings.

CABLE TRAYS September 2018 16139-2

Electrical Specification MZ & Partners Doha Port Redevelopment Project GP18182

D. All bends and tee shall be from manufacturer.No site fabrication is allowed.

E. Cables: Secure to tray / ladder with purpose made straps or saddles and arrange in one
layer only, evenly spaced, or as shown on the Drawings, with minimum spacing of one
diameter of the larger of the two adjacent cables or of a trefoil formation of single core
cable circuit.

F. Fasten cable tray / ladder supports securely to building structure as specified in Division 16
Section "Basic Electrical Materials and Methods," unless otherwise indicated.

G. Make connections to equipment with flanged fittings fastened to cable tray / ladder and to
equipment. Support cable tray / ladder independently of fittings. Do not carry weight of
cable tray / ladder on equipment enclosure.

H. Install expansion connectors where cable tray / ladder crosses a building expansion joint
and in cable tray / ladder runs that exceed 27 m. Make changes in direction and elevation
using standard fittings.

I. Make cable tray / ladder connections using standard fittings.

J. Locate cable tray / ladder above piping, unless accessibility to cable tray / ladder is
required or unless otherwise indicated.

K. Seal penetrations through fire and smoke barriers according to Division 7 Section
"Through-Penetration Firestop Systems."

L. Sleeves for Future Cables: Install capped sleeves for future cables through fire stopping-
sealed cable tray / ladder penetrations of fire and smoke barriers.

M. Workspace: Install cable trays / ladders with sufficient space to permit access for installing
cables. Minimum clearance of 250 mm is to be maintained between top of tray / ladder and
ceiling, beams and other services and between tray / ladders in multi-tier formation.

N. Barriers: Where tray / ladders carry conductors of different systems, such as power,
communications and data processing, or different insulation levels, such as 600V, 5000V,
and 20, 000 V use separate cable tray / ladders. In case of absolute necessity, install
insulating barriers to separate the systems after obtaining the Engineer’s approval.

0.2 CONNECTIONS

A. Ground cable trays / ladders according to manufacturer's instructions.

1.Tighten electrical connectors and terminals according to manufacturer's published torque-

tightening values.

0.3 FIELD QUALITY CONTROL

A. Grounding: Test cable trays / ladders to ensure electrical continuity of bonding and
grounding connections.

B. Grounding: Do not use metal trays / ladders as earth continuity conductor. Connect trays /
ladders by flexible tinned copper straps to nearest bare earthing conductor and at
maximum 30-m spacing.

C. Replace malfunctioning units.

0.4 CLEANING

CABLE TRAYS September 2018 16139-3

Electrical Specification MZ & Partners Doha Port Redevelopment Project GP18182

A. On completion of cable tray / ladder installation, including fittings, inspect exposed finish.
Remove burrs, dirt, and construction debris and repair damaged finishes, including chips,
scratches, and abrasions.

0.5 PROTECTION

A. Provide final protection and maintain conditions, in a manner acceptable to manufacturer

and Installer that ensure cable tray / ladder is without damage or deterioration at the time of
Substantial Completion.

1. Repair damage to galvanized finishes with zinc-rich paint recommended by cable tray /
ladder manufacturer.
2.Repair damage to PVC or paint finishes with matching touchup coating recommended by
cable tray / ladder manufacturer.

END OF SECTION 16139

CABLE TRAYS September 2018 16139-4