Professional Documents
Culture Documents
Appendix H PDF
Appendix H PDF
Force summary at pier base are subjected to Axial forces and biaxial moments
The force summary at point of inflextion includes following :
Weight of Pilecap
Horizontal forces are transferred upto point of inflexion considering portal action.
Estimating the pile forces for pier forces will lead to very less pile forces.
Hence pile forces are estimated considering the force summary at point of inflexion.
Strut & Tie model are prepared in 2 different STAAD model to find the tie tension forces at bottom and top of pilecap :
Model No 1.) Strut & Tie model wherein all piles are in compression - In such case, Pile reaction are calculated for V = 11630 kN & MT = 19311 kNm
Model No 2.) Strut & Tie model wherein 2 piles are in compression & remaining 2 piles are in tension. In such case, Pile reaction are calculated for ML = 10250 kNm
Tie forces found from above 2 models are added to find the design Tie forces.
Forces will be applied in STAAD model in form of pile reaction and support will be applied at Pier Equivalent force system Load location.
To find the Pier Equivalent force system location, we have checked following 2 approach.
1) Pier load (Or support) is applied at four points at pilecap top. These points are C.G. of quadrant of Pier.
2) Find the magnitude of compressive & tensile forces so that equivalent force system produces the same axial force.
The compressive and tensile regions are divided equally in 2 regions. The loads are located transversly at cg of column width.
P152_Metro_25m-25m_Stg_190320
SPACPL-INDUS (JV) Contract DC-04: YFC PROJECT PVT LTD.
Between Chainage 14480 to 18760m of
Aerocity to Tuglakabad Corridor of
Phase-IV of Delhi MRTS
No of Piles
C/C distance between piles = 4 Nos
Along Longitudinal direction = 3.50 m
Along Transverse direction = 3.50 m
Dimensions of pile cap
L B D
5.00 x 5.00 x 1.80 m
Clear cover = 0.075 m
Dia. Of reinf. = 0.032 m
Lever arm Z = 0.9 *( 1800 - 75 - 1.5 x 32 )
= 1.509 m = 1509 mm
Approach No. 1) Pier Load (Or support) is applied at four points (CG of quadrant of Pier) at pilecap top.
Long direction
2 T2 3
0.849
T1
1 4
(Refer Sketch No. 01)
Trans. C/C distance between C.G. of Pier quandrant= 0.849 m
Long. C/C distance between C.G. of Pier quandrant = 0.849 m
P152_Metro_25m-25m_Stg_190320
SPACPL-INDUS (JV) Contract DC-04: YFC PROJECT PVT LTD.
Between Chainage 14480 to 18760m of
Aerocity to Tuglakabad Corridor of
Phase-IV of Delhi MRTS
P152_Metro_25m-25m_Stg_190320
SPACPL-INDUS (JV) Contract DC-04: YFC PROJECT PVT LTD.
Between Chainage 14480 to 18760m of
Aerocity to Tuglakabad Corridor of
Phase-IV of Delhi MRTS
2 T2 3
0.674
T4
T1
1 4
(Refer Sketch No. 01)
Pie reaction in Pile No. 1 = 149 kN (Compressive)
Pile No. 2 = 5666 kN (Compressive)
Pile No. 3 = 5666 kN (Compressive)
Pile No. 4 = 149 kN (Compressive)
The above Pile reactions are applied in STAAD model No. 1 & Tie Forces at Pilecap bottom are listed below
TB-1 = -2995 kN (Tensile) TT-1 = 0 kN (Tensile)
TB-2 = -5306 kN (Tensile) TT-2 = 0 kN (Tensile)
TB-3 = -3796 kN (Tensile) TT-3 = 0 kN (Tensile)
TB-4 = -3796 kN (Tensile) TT-4 = 0 kN (Tensile)
P152_Metro_25m-25m_Stg_190320
SPACPL-INDUS (JV) Contract DC-04: YFC PROJECT PVT LTD.
Between Chainage 14480 to 18760m of
Aerocity to Tuglakabad Corridor of
Phase-IV of Delhi MRTS
Long direction
2 T4 3
0.541
T1
T3
1 4
(Refer Sketch No. 01)
P152_Metro_25m-25m_Stg_190320
SPACPL-INDUS (JV) Contract DC-04: YFC PROJECT PVT LTD.
Between Chainage 14480 to 18760m of
Aerocity to Tuglakabad Corridor of
Phase-IV of Delhi MRTS
Appendix H-2) Analysis of Pilecap Truss Analogy for Minimum Pile reaction case To Find maximum Tie force at Pilecap top Level
Minimum pile reaction = -2330 kN ( Refer Cl 6.10 )
Governing Load combination no = 437 (For Pile & Pilecap)
Corresponding Load combination=no 237 (For Pier)
Force summary at point of inflexion for Pile reaction under Load combination 437
V = 5908 kN
ML = 19810 kNm
MT = 6838 kNm
Pier Force summary under Load combination 237
V = 4950 kN
ML = 10079 kNm
MT = 3918 kNm
Approach No. 1) Pier Load (Or support) is applied at four points (CG of quadrant of Pier) at pilecap top.
Long direction
2 T2 3
0.849
T1
1 4
(Refer Sketch No. 01)
Model No. 5) Find Pile reaction for V = 5908 kN MT = 6838 kNm
Pie reaction in Pile No. 1 = 500 kN (Compressive)
Pile No. 2 = 500 kN (Compressive)
Pile No. 3 = 2454 kN (Compressive)
Pile No. 4 = 2454 kN (Compressive)
P152_Metro_25m-25m_Stg_190320
SPACPL-INDUS (JV) Contract DC-04: YFC PROJECT PVT LTD.
Between Chainage 14480 to 18760m of
Aerocity to Tuglakabad Corridor of
Phase-IV of Delhi MRTS
The above Pile reactions are applied in STAAD model No. 1 & Tie Forces at Pilecap bottom are listed below
TB-1 = -1875 kN (Tensile) TT-1 = 0 kN (Tensile)
TB-2 = -2156 kN (Tensile) TT-2 = 0 kN (Tensile)
TB-3 = -2156 kN (Tensile) TT-3 = 0 kN (Tensile)
TB-4 = -2156 kN (Tensile) TT-4 = 0 kN (Tensile)
Model No. 6) Find Pile reaction for ML = 19810 kNm
Pile reaction in Pile No. 1 = -2830 kN (Tensile)
Pile No. 2 = -2830 kN (Tensile)
Pile No. 3 = 2830 kN (Compressive)
Pile No. 4 = 2830 kN (Compressive)
The above Pile reactions are applied in STAAD model No. 1 & Tie Forces at Pilecap bottom & Top are listed below
TB-1 = -2487 kN (Tensile) TT-1 = -2487 kN (Tensile)
TB-2 = -2487 kN (Tensile) TT-2 = -2487 kN (Tensile)
TB-3 = -2487 kN (Tensile) TT-3 = -2487 kN (Tensile)
TB-4 = -2487 kN (Tensile) TT-4 = -2487 kN (Tensile)
Add Tie Forces of Model No. 1 & Model No. 2
TB-1 = -4362 kN (Tensile) TT-1 = -2487 kN (Tensile)
TB-2 = -4643 kN (Tensile) TT-2 = -2487 kN (Tensile)
TB-3 = -4643 kN (Tensile) TT-3 = -2487 kN (Tensile)
TB-4 = -4643 kN (Tensile) TT-4 = -2487 kN (Tensile)
Conclusion :
From the above 2 approaches, we can conclude that Bottom Tie force found from Apporach No. 1 is conservative. Same aaproach will be used for design.
Bottom Tie Force as per STM done in STAAD = 6265 kN Tie force considered in design in Cl No. 7.0 = 6263 kN Same
Maximum Tie force in Top is 2487 kN
2
Reinforcement required 5717 mm in Half Pilecap
Pile strip width 1.5 m
2
80% in Pile strip 3049 mm /m
2
Provided reinforcement 3506 mm /m OK
Hence pilecap design for top face as flexure and check for shear will govern the design requirement and will comply the Tie force reinforcement demand
as per STM approach.
P152_Metro_25m-25m_Stg_190320
C
L OF PIER
LONGITUDINAL
DIRECTION
SKETCH - 01 C
L OF PIER
LONGITUDINAL
DIRECTION
17.66 MPa
159
478
541
514
NEUTRAL AXIS
841
756
CL OF PIER CL OF PIER
674
TRANS. TRANS.
DIREC. DIREC.
423
1522
NEUTRAL AXIS
810
739 261
21.59 MPa
LINEAR STRESS DISTRIBUTION OVER PIER CROSS SECTION & LINEAR STRESS DISTRIBUTION OVER PIER CROSS SECTION &
EQUIVALENT FORCE SYSTEM LOAD LOCATIONS EQUIVALENT FORCE SYSTEM LOAD LOCATIONS
FOR V = 11630 kN & MT = 19311 kN m FOR ML = 10250 kN m
APPENDIX – H-1
MODEL NO. 1
STRUT TIE MODEL FOR 4 PILE IN
COMPRESSION
APPLIED LOAD:
AXIAL FORCE & TRANSVERSE MOMENT
(FOR MAXIMUM PILE REACTION LOAD
COMBINATION)
Job No Sheet No Rev
1
Part
Software licensed to SPACPL
Job Title Ref
By Date23-Mar-20 Chd
12 18
2 15
5666 kN
13
16
8
19
1
9 5666 kN
20
6 3
YX 5
Z
149.0000 kN
7
Load 1
149.0000 kN
Print Time/Date: 26/03/2020 10:44 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Thursday, March 26, 2020, 10:52 AM
PAGE NO. 1
****************************************************
* *
* STAAD.Pro V8i SELECTseries6 *
* Version 20.07.11.70 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= MAR 26, 2020 *
* Time= 10:46:35 *
* *
* USER ID: SPACPL *
****************************************************
1. STAAD SPACE
INPUT FILE: C:\30TA\Substructure Analysis\Metro\P152\STAAD\New folder\Model 1_STM_Pilecap_4 pile compr.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 23-MAR-20
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 -1.75 0 -1.75; 2 1.75 0 -1.75; 3 1.75 0 1.75; 4 -1.75 0 1.75
9. 5 -0.424 1.509 -0.424; 6 0.424 1.509 -0.424; 7 0.424 1.509 0.424
10. 8 -0.424 1.509 0.424; 9 -0.424 0 -0.424; 10 -0.424 0 0.424
11. * PILE CO-ORDINATES @ PILECAP BOTTOM REINF LVL - PILE REACTION
12. * PIER CO-ORDINATES @ PILECAP TOP REINF LVL - ACT AS SUPPORT
13. * TENSION REGION IN COLUMN TO ANCHOR TILL PILECAP BOTTOM
14. * PILE CO-ORDINATES @ PILECAP TOP REINF LVL - DUE TO PILE IN TENSION
15. MEMBER INCIDENCES
16. 1 1 2; 2 2 3; 3 3 4; 4 4 1; 5 1 9; 6 9 10; 7 10 4; 8 5 9; 9 8 10; 12 6 2
17. 13 6 9; 15 7 3; 16 7 10; 18 6 7; 19 6 1; 20 7 4
18. * BOTTOM TIES
19. * PIER / PILE TENSION - ANCHOR
20. * STRUT
21. * TOP TIES
22. DEFINE MATERIAL START
23. ISOTROPIC CONCRETE
24. E 2.985E+007
25. POISSON 0.17
26. DENSITY 25
27. ALPHA 1E-005
28. DAMP 0.05
29. TYPE CONCRETE
30. STRENGTH FCU 40000
31. END DEFINE MATERIAL
32. MEMBER PROPERTY AMERICAN
33. 1 TO 9 12 13 15 16 18 TO 20 PRIS YD 0.5
34. CONSTANTS
35. MATERIAL CONCRETE MEMB 1 TO 9 12 13 15 16 18 TO 20
36. SUPPORTS
37. 5 TO 8 FIXED BUT FX FZ MX MY MZ
38. MEMBER RELEASE
39. 1 TO 9 12 13 15 16 18 TO 20 START MY MZ
40. 1 TO 9 12 13 15 16 18 TO 20 END MY MZ
41. LOAD 1 LOADTYPE NONE TITLE LOAD CASE 1
42. JOINT LOAD
43. 1 FY 149
44. 4 FY 149
46. 2 FY 5666
47. 3 FY 5666
49. PERFORM ANALYSIS
P R O B L E M S T A T I S T I C S
-----------------------------------
THE ABOVE CONDITIONS COULD ALSO BE CAUSED BY VERY STIFF OR VERY WEAK
ELEMENTS AS WELL AS TRUE SINGULARITIES.
51. FINISH
By Date23-Mar-20 Chd
14 22
21
18 17
12
23
15
13
24
8 2
16
19
10 9
1
Y
X
Z
20
5 6
11
3
4 7
Load 1
Print Time/Date: 26/03/2020 11:01 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Thursday, March 26, 2020, 11:02 AM
PAGE NO. 1
****************************************************
* *
* STAAD.Pro V8i SELECTseries6 *
* Version 20.07.11.70 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= MAR 26, 2020 *
* Time= 11: 0: 4 *
* *
* USER ID: SPACPL *
****************************************************
1. STAAD SPACE
INPUT FILE: C:\30TA\Substructure Analysis\Metro\P152\STAAD\New folder\Model 2_STM_Pilecap_2 pile tensi.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 23-MAR-20
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. * PILE CO-ORDINATES @ PILECAP BOTTOM REINF LVL - PILE REACTION
9. 1 -1.750 0.000 -1.750 ; 2 1.750 0.000 -1.750
10. 3 1.750 0.000 1.750 ; 4 -1.750 0.000 1.750
11. * PIER CO-ORDINATES @ PILECAP TOP REINF LVL - ACT AS SUPPORT
12. 5 -0.424 1.509 -0.424 ; 6 0.424 1.509 -0.424
13. 7 0.424 1.509 0.424 ; 8 -0.424 1.509 0.424
14. * TENSION REGION IN COLUMN TO ANCHOR TILL PILECAP BOTTOM
15. 9 -0.424 0.000 -0.424 ; 10 -0.424 0.000 0.424
16. * PILE CO-ORDINATES @ PILECAP TOP REINF LVL - DUE TO PILE IN TENSION
17. 11 -1.750 1.509 -1.750 ; 12 1.750 1.509 -1.750
18. 13 1.750 1.509 1.750 ; 14 -1.750 1.509 1.750
20. MEMBER INCIDENCES
21. * BOTTOM TIES
22. 1 1 2
23. 2 2 3
24. 3 3 4
25. 4 4 1
26. 5 1 9
27. 6 9 10
28. 7 10 4
29. * PIER / PILE TENSION - ANCHOR
30. 8 5 9
31. 9 8 10
32. 10 1 11
33. 11 4 14
34. * STRUT
35. 12 6 2
36. 13 6 9
37. 14 6 12
38. 15 7 3
39. 16 7 10
40. 17 7 13
41. 18 6 7
42. 19 11 9
43. 20 14 10
44. * TOP TIES
45. 21 11 12
46. 22 12 13
47. 23 13 14
48. 24 14 11
49. DEFINE MATERIAL START
50. ISOTROPIC CONCRETE
51. E 2.985E+007
52. POISSON 0.17
53. DENSITY 25
54. ALPHA 1E-005
55. DAMP 0.05
56. TYPE CONCRETE
57. STRENGTH FCU 40000
58. END DEFINE MATERIAL
59. MEMBER PROPERTY
60. 1 TO 24 PRIS YD 0.5
61. CONSTANTS
62. MATERIAL CONCRETE MEMB 1 TO 24
63. SUPPORTS
64. 5 TO 8 FIXED BUTT FX FZ MX MY MZ
65. MEMBER RELEASE
66. 1 TO 24 START MY MZ
67. 1 TO 24 END MY MZ
68. LOAD 1 LOADTYPE NONE TITLE LOAD CASE 1
69. JOINT LOAD
70. 1 FY -1464
71. 4 FY -1464
73. 2 FY 1464
74. 3 FY 1464
76. PERFROM ANALYSIS
P R O B L E M S T A T I S T I C S
-----------------------------------
THE ABOVE CONDITIONS COULD ALSO BE CAUSED BY VERY STIFF OR VERY WEAK
ELEMENTS AS WELL AS TRUE SINGULARITIES.
78. FINISH
By Date23-Mar-20 Chd
18
12
15
13
19
8
16
2
9
20
1
Y
X 5
Z 6
4
7
Load 1
Print Time/Date: 26/03/2020 11:11 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Thursday, March 26, 2020, 11:12 AM
PAGE NO. 1
****************************************************
* *
* STAAD.Pro V8i SELECTseries6 *
* Version 20.07.11.70 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= MAR 26, 2020 *
* Time= 11:12:14 *
* *
* USER ID: SPACPL *
****************************************************
1. STAAD SPACE
INPUT FILE: C:\30TA\Substructure Analysis\Metro\P152\STAAD\New folder\Model 3_STM_Pilecap_4 pile compr.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 23-MAR-20
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 -1.75 0 -1.75; 2 1.75 0 -1.75; 3 1.75 0 1.75; 4 -1.75 0 1.75
9. 5 -0.514 1.509 -0.756; 6 0.739 1.509 -0.337; 7 0.739 1.509 0.337
10. 8 -0.514 1.509 0.756; 9 -0.514 0 -0.756; 10 -0.514 0 0.756
11. * PILE CO-ORDINATES @ PILECAP BOTTOM REINF LVL - PILE REACTION
12. * PIER CO-ORDINATES @ PILECAP TOP REINF LVL - ACT AS SUPPORT
13. * TENSION REGION IN COLUMN TO ANCHOR TILL PILECAP BOTTOM
14. * PILE CO-ORDINATES @ PILECAP TOP REINF LVL - DUE TO PILE IN TENSION
15. MEMBER INCIDENCES
16. 1 1 2; 2 2 3; 3 3 4; 4 4 1; 5 1 9; 6 9 10; 7 10 4; 8 5 9; 9 8 10; 12 6 2
17. 13 6 9; 15 7 3; 16 7 10; 18 6 7; 19 6 1; 20 7 4
18. * BOTTOM TIES
19. * PIER / PILE TENSION - ANCHOR
20. * STRUT
21. * TOP TIES
22. DEFINE MATERIAL START
23. ISOTROPIC CONCRETE
24. E 2.985E+007
25. POISSON 0.17
26. DENSITY 25
27. ALPHA 1E-005
28. DAMP 0.05
29. TYPE CONCRETE
30. STRENGTH FCU 40000
31. END DEFINE MATERIAL
32. MEMBER PROPERTY AMERICAN
33. 1 TO 9 12 13 15 16 18 TO 20 PRIS YD 0.5
34. CONSTANTS
35. MATERIAL CONCRETE ALL
36. SUPPORTS
37. 5 TO 8 FIXED BUT FX FZ MX MY MZ
38. MEMBER RELEASE
39. 1 TO 9 12 13 15 16 18 TO 20 START MY MZ
40. 1 TO 9 12 13 15 16 18 TO 20 END MY MZ
41. LOAD 1 LOADTYPE NONE TITLE LOAD CASE 1
42. JOINT LOAD
43. 1 FY 149
44. 4 FY 149
45. 2 FY 5666
46. 3 FY 5666
47. PERFORM ANALYSIS
P R O B L E M S T A T I S T I C S
-----------------------------------
THE ABOVE CONDITIONS COULD ALSO BE CAUSED BY VERY STIFF OR VERY WEAK
ELEMENTS AS WELL AS TRUE SINGULARITIES.
49. FINISH
By Date23-Mar-20 Chd
14
22
21
18
17
12
23
13 15
24 8
19 16 2
10
1
9
Y
X
20
5
Z 6
11
3
4
7
Load 1
Print Time/Date: 26/03/2020 11:13 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Thursday, March 26, 2020, 11:14 AM
PAGE NO. 1
****************************************************
* *
* STAAD.Pro V8i SELECTseries6 *
* Version 20.07.11.70 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= MAR 26, 2020 *
* Time= 11:13:51 *
* *
* USER ID: SPACPL *
****************************************************
1. STAAD SPACE
INPUT FILE: C:\30TA\Substructure Analysis\Metro\P152\STAAD\New folder\Model 4_STM_Pilecap_2 pile tensi.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 23-MAR-20
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 -1.75 0 -1.75; 2 1.75 0 -1.75; 3 1.75 0 1.75; 4 -1.75 0 1.75
9. 5 -0.423 1.509 -0.81; 6 0.841 1.509 -0.271; 7 0.841 1.509 0.271
10. 8 -0.423 1.509 0.81; 9 -0.423 0 -0.81; 10 -0.423 0 0.81; 11 -1.75 1.509 -1.75
11. 12 1.75 1.509 -1.75; 13 1.75 1.509 1.75; 14 -1.75 1.509 1.75
12. * PILE CO-ORDINATES @ PILECAP BOTTOM REINF LVL - PILE REACTION
13. * PIER CO-ORDINATES @ PILECAP TOP REINF LVL - ACT AS SUPPORT
14. * TENSION REGION IN COLUMN TO ANCHOR TILL PILECAP BOTTOM
15. * PILE CO-ORDINATES @ PILECAP TOP REINF LVL - DUE TO PILE IN TENSION
16. MEMBER INCIDENCES
17. 1 1 2; 2 2 3; 3 3 4; 4 4 1; 5 1 9; 6 9 10; 7 10 4; 8 5 9; 9 8 10; 10 1 11
18. 11 4 14; 12 6 2; 13 6 9; 14 6 12; 15 7 3; 16 7 10; 17 7 13; 18 6 7; 19 11 9
19. 20 14 10; 21 11 12; 22 12 13; 23 13 14; 24 14 11
20. * BOTTOM TIES
21. * PIER / PILE TENSION - ANCHOR
22. * STRUT
23. * TOP TIES
24. DEFINE MATERIAL START
25. ISOTROPIC CONCRETE
26. E 2.985E+007
27. POISSON 0.17
28. DENSITY 25
29. ALPHA 1E-005
30. DAMP 0.05
31. TYPE CONCRETE
32. STRENGTH FCU 40000
33. END DEFINE MATERIAL
34. MEMBER PROPERTY AMERICAN
35. 1 TO 24 PRIS YD 0.5
36. CONSTANTS
37. MATERIAL CONCRETE ALL
38. SUPPORTS
P R O B L E M S T A T I S T I C S
-----------------------------------
THE ABOVE CONDITIONS COULD ALSO BE CAUSED BY VERY STIFF OR VERY WEAK
ELEMENTS AS WELL AS TRUE SINGULARITIES.
51. FINISH
By Date23-Mar-20 Chd
18
12
13 15
19
8
16
9 2
1
20
Y 5
X 6
Z
3
4
7
Load 1
Print Time/Date: 26/03/2020 11:17 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Thursday, March 26, 2020, 11:18 AM
PAGE NO. 1
****************************************************
* *
* STAAD.Pro V8i SELECTseries6 *
* Version 20.07.11.70 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= MAR 26, 2020 *
* Time= 10:49:39 *
* *
* USER ID: SPACPL *
****************************************************
1. STAAD SPACE
INPUT FILE: C:\30TA\Substructure Analysis\Metro\P152\STAAD\New folder\Model 5_STM_Pilecap_4 pile compr.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 23-MAR-20
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. 1 -1.75 0 -1.75; 2 1.75 0 -1.75; 3 1.75 0 1.75; 4 -1.75 0 1.75
9. 5 -0.424 1.509 -0.424; 6 0.424 1.509 -0.424; 7 0.424 1.509 0.424
10. 8 -0.424 1.509 0.424; 9 -0.424 0 -0.424; 10 -0.424 0 0.424
11. * PILE CO-ORDINATES @ PILECAP BOTTOM REINF LVL - PILE REACTION
12. * PIER CO-ORDINATES @ PILECAP TOP REINF LVL - ACT AS SUPPORT
13. * TENSION REGION IN COLUMN TO ANCHOR TILL PILECAP BOTTOM
14. * PILE CO-ORDINATES @ PILECAP TOP REINF LVL - DUE TO PILE IN TENSION
15. MEMBER INCIDENCES
16. 1 1 2; 2 2 3; 3 3 4; 4 4 1; 5 1 9; 6 9 10; 7 10 4; 8 5 9; 9 8 10; 12 6 2
17. 13 6 9; 15 7 3; 16 7 10; 18 6 7; 19 6 1; 20 7 4
18. * BOTTOM TIES
19. * PIER / PILE TENSION - ANCHOR
20. * STRUT
21. * TOP TIES
22. DEFINE MATERIAL START
23. ISOTROPIC CONCRETE
24. E 2.985E+007
25. POISSON 0.17
26. DENSITY 25
27. ALPHA 1E-005
28. DAMP 0.05
29. TYPE CONCRETE
30. STRENGTH FCU 40000
31. END DEFINE MATERIAL
32. MEMBER PROPERTY AMERICAN
33. 1 TO 9 12 13 15 16 18 TO 20 PRIS YD 0.5
34. CONSTANTS
35. MATERIAL CONCRETE MEMB 1 TO 9 12 13 15 16 18 TO 20
36. SUPPORTS
37. 5 TO 8 FIXED BUT FX FZ MX MY MZ
38. MEMBER RELEASE
39. 1 TO 9 12 13 15 16 18 TO 20 START MY MZ
40. 1 TO 9 12 13 15 16 18 TO 20 END MY MZ
41. LOAD 1 LOADTYPE NONE TITLE LOAD CASE 1
42. JOINT LOAD
43. 1 FY 500
44. 4 FY 500
46. 2 FY 2454
47. 3 FY 2454
49. PERFORM ANALYSIS
P R O B L E M S T A T I S T I C S
-----------------------------------
THE ABOVE CONDITIONS COULD ALSO BE CAUSED BY VERY STIFF OR VERY WEAK
ELEMENTS AS WELL AS TRUE SINGULARITIES.
51. FINISH
By Date23-Mar-20 Chd
14 22
21
12 18 17
2 15
13 23
1 8 16
19 24
10 9
YX 5 6 20
Z 3
11
4 7
Load 1
Print Time/Date: 26/03/2020 11:20 STAAD.Pro V8i (SELECTseries 6) 20.07.11.70 Print Run 1 of 1
Thursday, March 26, 2020, 11:21 AM
PAGE NO. 1
****************************************************
* *
* STAAD.Pro V8i SELECTseries6 *
* Version 20.07.11.70 *
* Proprietary Program of *
* Bentley Systems, Inc. *
* Date= MAR 26, 2020 *
* Time= 11:21: 0 *
* *
* USER ID: SPACPL *
****************************************************
1. STAAD SPACE
INPUT FILE: C:\30TA\Substructure Analysis\Metro\P152\STAAD\New folder\Model 6_STM_Pilecap_2 pile tensi.. .STD
2. START JOB INFORMATION
3. ENGINEER DATE 23-MAR-20
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. UNIT METER KN
7. JOINT COORDINATES
8. * PILE CO-ORDINATES @ PILECAP BOTTOM REINF LVL - PILE REACTION
9. 1 -1.750 0.000 -1.750 ; 2 1.750 0.000 -1.750
10. 3 1.750 0.000 1.750 ; 4 -1.750 0.000 1.750
11. * PIER CO-ORDINATES @ PILECAP TOP REINF LVL - ACT AS SUPPORT
12. 5 -0.424 1.509 -0.424 ; 6 0.424 1.509 -0.424
13. 7 0.424 1.509 0.424 ; 8 -0.424 1.509 0.424
14. * TENSION REGION IN COLUMN TO ANCHOR TILL PILECAP BOTTOM
15. 9 -0.424 0.000 -0.424 ; 10 -0.424 0.000 0.424
16. * PILE CO-ORDINATES @ PILECAP TOP REINF LVL - DUE TO PILE IN TENSION
17. 11 -1.750 1.509 -1.750 ; 12 1.750 1.509 -1.750
18. 13 1.750 1.509 1.750 ; 14 -1.750 1.509 1.750
20. MEMBER INCIDENCES
21. * BOTTOM TIES
22. 1 1 2
23. 2 2 3
24. 3 3 4
25. 4 4 1
26. 5 1 9
27. 6 9 10
28. 7 10 4
29. * PIER / PILE TENSION - ANCHOR
30. 8 5 9
31. 9 8 10
32. 10 1 11
33. 11 4 14
34. * STRUT
35. 12 6 2
36. 13 6 9
37. 14 6 12
38. 15 7 3
39. 16 7 10
40. 17 7 13
41. 18 6 7
42. 19 11 9
43. 20 14 10
44. * TOP TIES
45. 21 11 12
46. 22 12 13
47. 23 13 14
48. 24 14 11
49. DEFINE MATERIAL START
50. ISOTROPIC CONCRETE
51. E 2.985E+007
52. POISSON 0.17
53. DENSITY 25
54. ALPHA 1E-005
55. DAMP 0.05
56. TYPE CONCRETE
57. STRENGTH FCU 40000
58. END DEFINE MATERIAL
59. MEMBER PROPERTY
60. 1 TO 24 PRIS YD 0.5
61. CONSTANTS
62. MATERIAL CONCRETE MEMB 1 TO 24
63. SUPPORTS
64. 5 TO 8 FIXED BUTT FX FZ MX MY MZ
65. MEMBER RELEASE
66. 1 TO 24 START MY MZ
67. 1 TO 24 END MY MZ
68. LOAD 1 LOADTYPE NONE TITLE LOAD CASE 1
69. JOINT LOAD
70. 1 FY -2830
71. 4 FY -2830
73. 2 FY 2830
74. 3 FY 2830
76. PERFROM ANALYSIS
P R O B L E M S T A T I S T I C S
-----------------------------------
THE ABOVE CONDITIONS COULD ALSO BE CAUSED BY VERY STIFF OR VERY WEAK
ELEMENTS AS WELL AS TRUE SINGULARITIES.
78. FINISH