HM 2019TableofContents PDF

PART 1—STANDARD SPECIFICATIONS AND STANDARD PRACTICES
SUBJECT SEQUENCE TABLE OF CONTENTS
AGGREGATES
M 6-13 Fine Aggregate for Hydraulic Cement Concrete
M 17-11 (2015) Mineral Filler for Bituminous Paving Mixtures
M 29-12 (2016) Fine Aggregate for Bituminous Paving Mixtures
M 43-05 (2013) Sizes of Aggregate for Road and Bridge Construction
M 45-16 Aggregate for Masonry Mortar
M 80-13 (2017) Coarse Aggregate for Hydraulic Cement Concrete
M 195-11 (2015) Lightweight Aggregates for Structural Concrete
M 327-18 Processing Additions for Use in the Manufacture of Hydraulic Cements
R 76-16 Reducing Samples of Aggregate to Testing Size
BITUMINOUS MATERIALS
M 81-92 (2017) Cutback Asphalt (Rapid-Curing Type)

M 82-17 Cutback Asphalt (Medium-Curing Type)
M 140-16 Emulsified Asphalt
M 156-13 (2017) Requirements for Mixing Plants for Hot-Mixed, Hot-Laid Bituminous Paving
Mixtures
M 208-16 Cationic Emulsified Asphalt
M 226-80 (2017) Viscosity-Graded Asphalt Cement
M 303-89 (2014) Lime for Asphalt Mixtures
M 316-16 Polymer-Modified Emulsified Asphalt
M 320-17 Performance-Graded Asphalt Binder
M 323-13 Superpave Volumetric Mix Design
M 325-08 (2017) Stone Matrix Asphalt (SMA)
M 332-14 Performance-Graded Asphalt Binder Using Multiple Stress Creep Recovery
(MSCR) Test
R 5-17 Selection and Use of Emulsified Asphalts
R 15-00 (2017) Asphalt Additives and Modifiers
R 26-01 (2013) Certifying Suppliers of Performance-Graded Asphalt Binders
R 28-12 (2016) Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel
(PAV)
R 29-15 Grading or Verifying the Performance Grade (PG) of an Asphalt Binder
R 30-02 (2015) Mixture Conditioning of Hot Mix Asphalt (HMA)
© 2018 by the American Association of State Highway and Transportation Officials.

All rights reserved. Duplication is a violation of applicable law.
R 28-12 (2016) Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel
(PAV)
R 35-17 Superpave Volumetric Design for Asphalt Mixtures
R 46-08 (2017) Designing Stone Matrix Asphalt (SMA)
R 47-14 (2018) Reducing Samples of Hot Mix Asphalt (HMA) to Testing Size
R 49-09 (2018) Determination of Low-Temperature Performance Grade (PG) of Asphalt
Binders
R 59-11 (2015) Recovery of Asphalt Binder from Solution by Abson Method
R 62-13 (2017) Developing Dynamic Modulus Master Curves for Asphalt Mixtures
R 66-16 Sampling Asphalt Materials
R 67-16 Sampling Asphalt Mixtures after Compaction (Obtaining Cores)
R 68-15 Preparation of Asphalt Mixtures by Means of the Marshall Apparatus
R 77-16 Certifying Suppliers of Emulsified Asphalt
R 78-16 Recovering Residue from Emulsified Asphalt Using Low-Temperature
Evaporative Techniques
R 79-16 Vacuum Drying Compacted Asphalt Specimens
R 83-17 Preparation of Cylindrical Performance Test Specimens Using the Superpave
Gyratory Compactor (SGC)
R 84-17 Developing Dynamic Modulus Master Curves for Asphalt Mixtures Using
the Asphalt Mixture Performance Tester (AMPT)
R 92-18 Evaluating the Elastic Behavior of Asphalt Binders Using the Multiple Stress
Creep Recovery (MSCR) Test
BOX CULVERT, CULVERT PIPE, AND DRAIN TILE
M 36-16 Corrugated Steel Pipe, Metallic-Coated, for Sewers and Drains

M 86M/M 86-17 Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe
M 167M/M 167-17 Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe,
Pipe-Arches, and Arches
M 170-17 Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
M 170M-17 Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe [Metric]
M 175M/M 175-05 (2013) Perforated Concrete Pipe
M 176M/M 176-17 Porous Concrete Pipe
M 178M/M 178-17 Concrete Drain Tile
M 190-04 (2017) Asphalt-Coated Corrugated Metal Culvert Pipe and Pipe-Arches
M 196-16 Corrugated Aluminum Pipe for Sewers and Drains
M 197-06 (2016) Aluminum Alloy Sheet for Corrugated Aluminum Pipe
M 199M/M 199-17 Precast Reinforced Concrete Manhole Sections
M 206M/M 206-17 Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe
M 207M/M 207-17 Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe
M 218-03 (2016) Steel Sheet, Zinc-Coated (Galvanized), for Corrugated Steel Pipe
M 219-92 (2017) Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-
Arches, and Arches
M 242M/M 242-17 Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe
M 243-96 (2017) Field-Applied Coating of Corrugated Metal Structural Plate for Pipe, Pipe-
Arches, and Arches
M 245-16 Corrugated Steel Pipe, Polymer-Precoated, for Sewers and Drains
M 246-15 Steel Sheet, Metallic-Coated and Polymer-Precoated, for Corrugated Steel
Pipe
M 252-18 Corrugated Polyethylene Drainage Pipe
M 259-17 Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and
Sewers
M 259M-17 Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and
Sewers [Metric]
M 262-11 (2015) Concrete Pipe and Related Products
M 273-17 Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and
Sewers with Less Than 2 ft of Cover Subjected to Highway Loadings
Sewers with Less Than 0.6 m of Cover Subjected to Highway Loadings
[Metric]
M 274-87 (2017) Steel Sheet, Aluminum-Coated (Type 2), for Corrugated Steel Pipe
M 278-15 Class PS46 Poly(Vinyl Chloride) (PVC) Pipe
M 289-91 (2017) Aluminum-Zinc Alloy Coated Sheet Steel for Corrugated Steel Pipe
M 294-18 Corrugated Polyethylene Pipe, 300- to 1500-mm (12- to 60-in.) Diameter
M 304-11 (2015) Poly(Vinyl Chloride) (PVC) Profile Wall Drain Pipe and Fittings Based on
Controlled Inside Diameter
M 306-10 (2015) Drainage, Sewer, Utility, and Related Castings
M 326-18 Polyethylene (PE) Liner Pipe, 300- to 1600-mm Diameter, Based on
Controlled Outside Diameter
M 330-18 Polypropylene Pipe, 300- to 1500-mm (12- to 60-in.) Diameter
M 335-18 Steel-Reinforced Polyethylene (PE) Ribbed Pipe, 300- to 1500-mm (12- to
60-in.) Diameter
R 63-13 (2017) Solid Wall High-Density Polyethelene (HDPE) Conduit for Non-Pressure
Applications Used for the Protection of Power and Telecommunications
Cables
R 73-16 Evaluation of Precast Concrete Drainage Products
R 82-17 Pipe Joint Selection for Highway Culvert and Storm Drains
CONCRETE, CURING MATERIALS, AND ADMIXTURES
M 154M/M 154-12 (2016) Air-Entraining Admixtures for Concrete

M 157-13 (2017) Ready-Mixed Concrete
M 182-05 (2017) Burlap Cloth Made from Jute or Kenaf and Cotton Mats
M 194M/M 194-13 (2017) Chemical Admixtures for Concrete
M 205M/M 205-11 (2019) Molds for Forming Concrete Test Cylinders Vertically
M 224-91 (2019) Use of Protective Sealers for Portland Cement Concrete
M 233-86 (2014) Boiled Linseed Oil Mixture for Treatment of Portland Cement Concrete
M 241M/M 241-13 (2017) Concrete Made by Volumetric Batching and Continuous Mixing
M 295-19 Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
M 302-19 Slag Cement for Use in Concrete and Mortars
R 39-19 Making and Curing Concrete Test Specimens in the Laboratory
R 60-12 (2016) Sampling Freshly Mixed Concrete
R 64-17 Sampling and Fabrication of 50-mm (2-in.) Cube Specimens Using Grout
(Non-Shrink) or Mortar
R 70M/R 70-18 Use of Apparatus for the Determination of Length Change of Hardened
Cement Paste, Mortar, and Concrete
R 72-16 Match Curing of Concrete Test Specimens
R 80-17 Determining the Reactivity of Concrete Aggregates and Selecting
Appropriate Measures for Preventing Deleterious Expansion in New
Concrete Construction
R 81-17 Static Segregation of Hardened Self-Consolidating Concrete (SCC)
Cylinders
ENVIRONMENTAL TESTS
R 23-99 (2018) Chemical, Biological, and Physical Analysis of Water

R 24-99 (2018) Collection and Preservation of Water Samples
GUARDRAIL AND FENCING
M 180-12 (2017) Corrugated Sheet Steel Beams for Highway Guardrail

M 181-10 (2015) Chain-Link Fence
M 269-96 (2018) Turnbuckles and Shackles
M 279-14 (2018) Metallic-Coated, Steel Woven Wire Fence Fabric
M 280-14 (2018) Metallic-Coated (Carbon) Steel Barbed Wire
M 281-96 (2018) Steel Fence Posts and Assemblies, Hot-Wrought
HYDRAULIC CEMENT
M 85-19 Portland Cement

M 240M/M 240-19 Blended Hydraulic Cement
M 307-13 (2017) Silica Fume Used in Cementitious Mixtures
M 321-04 (2017) High-Reactivity Pozzolans for Use in Hydraulic-Cement Concrete, Mortar,
and Grout
R 71-16 Sampling and Amount of Testing of Hydraulic Cement
JOINT FILLER AND ASPHALT PLANK
M 33-99 (2016) Preformed Expansion Joint Filler for Concrete (Bituminous Type)
M 153-06 (2016) Preformed Sponge Rubber, Cork, and Recycled Rubber Expansion Joint
Fillers for Concrete Paving and Structural Construction
M 213-01 (2015) Preformed Expansion Joint Fillers for Concrete Paving and Structural
Construction (Nonextruding and Resilient Bituminous Types)
M 251-06 (2016) Plain and Laminated Elastomeric Bridge Bearings
M 297-10 (2015) Preformed Polychloroprene Elastomeric Joint Seals for Bridges
R 50-09 (2018) Geosynthetic Reinforcement of the Aggregate Base Course of Flexible
Pavement Structures
METALLIC MATERIALS FOR BRIDGES
M 102M/M 102-06 (2016) Steel Forgings, Carbon and Alloy, for General Industrial Use
M 103M/M 103-12 (2016) Steel Castings, Carbon, for General Application
M 105-09 (2018) Gray Iron Castings
M 111M/M 111-15 Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
M 163M/M 163-07 (2016) Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for
General Application
M 169-15 Steel Bars, Carbon and Alloy, Cold-Finished
M 202M/M 202-08 (2016) Steel Sheet Piling
M 227M/M 227-13 (2017) Steel Bars, Carbon, Merchant Quality, Mechanical Properties
M 232M/M 232-10 (2015) Zinc Coating (Hot-Dip) on Iron and Steel Hardware
M 255M/M 255-05 (2018) Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties
M 270M/M 270-15 Structural Steel for Bridges
M 277-06 (2015) Wire Rope and Sockets for Movable Bridges
M 285M/M 285-11 (2015) Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service
M 292M/M 292-15 Carbon and Alloy Steel Nuts for Bolts for High-Pressure or High-
Temperature Service, or Both
M 314-90 (2018) Steel Anchor Bolts
M 333-16 Detectable Warning Surfaces
M 334M/M 334-17 Uncoated, Corrosion-Resistant, Deformed and Plain Chromium Alloyed,

Billet-Steel Bars for Concrete Reinforcement and Dowels
M 336M/M 336-18 Steel Wire and Welded Wire, Plain and Deformed, for Concrete
Reinforcement
MISCELLANEOUS
M 143-14 (2018) Sodium Chloride

M 144-14 (2018) Calcium Chloride
M 230-07 (2016) Expanded and Extruded Foam Board (Polystyrene)
M 235M/M 235-13 (2018) Epoxy Resin Adhesives
R 8-96 (2015) Evaluation of Transportation-Related Earthborne Vibrations
R 10-06 (2016) Definition of Terms Related to Quality and Statistics as Used in Highway
Construction
R 25-19 Technician Training and Certification Programs

R 34-03 (2018) Evaluating Deicing Chemicals
R 44-07 (2018) Independent Assurance (IA) Programs
R 89-18 Accreditation Bodies Operating in the Fields of Construction Materials
Testing and Inspection
PAINTING AND TRAFFIC MARKING AND SIGNING
M 237-96 (2014) Epoxy Resin Adhesives for Bonding Traffic Markers to Hardened Portland
Cement and Asphalt Concrete
M 247-13 (2018) Glass Beads Used in Pavement Markings
M 249-12 (2016) White and Yellow Reflective Thermoplastic Striping Material (Solid Form)
M 268-15 Retroreflective Sheeting for Flat and Vertical Traffic Control Applications
M 290-96 (2018) Acrylic Prismatic Reflectors and Embossed Aluminum Frames for Signs
M 300-03 (2017) Inorganic Zinc-Rich Primer
R 31-09 (2014) Evaluation of Protective Coating Systems for Structural Steel
PAVEMENT SURFACE AND STRUCTURE CHARACTERISTICS

M 328-14 (2018) Inertial Profiler
M 331-17 Smoothness of Pavement in Weigh-in-Motion (WIM) Systems
R 36-17 Evaluating Faulting of Concrete Pavements
R 37-04 (2018) Application of Ground Penetrating Radar (GPR) to Highways
R 40-10 (2018) Measuring Pavement Profile Using a Rod and Level
R 41-05 (2015) Discontinued—Measuring Pavement Profile Using a Dipstick®
R 43-13 (2017) Quantifying Roughness of Pavements
R 54-14 (2018) Accepting Pavement Ride Quality When Measured Using Inertial Profiling
Systems
R 56-14 (2018) Certification of Inertial Profiling Systems

R 57-14 (2018) Operating Inertial Profiling Systems
R 85-18 Quantifying Cracks in Asphalt Pavement Surfaces from Collected Pavement
Images Utilizing Automated Methods
R 86-18 Collecting Images of Pavement Surfaces for Distress Detection
R 87-18 Determining Pavement Deformation Parameters and Cross Slope from
Collected Transverse Profiles
R 88-18 Collecting the Transverse Pavement Profile
QUALITY ASSURANCE
R 9-05 (2018) Acceptance Sampling Plans for Highway Construction

R 18-18 Establishing and Implementing a Quality Management System for
Construction Materials Testing Laboratories
R 20-99 (2017) Procedures for Measuring Highway Noise
R 38-10 (2018) Quality Assurance of Standard Manufactured Materials
R 42-06 (2016) Developing a Quality Assurance Plan for Hot Mix Asphalt (HMA)
R 61-12 (2016) Establishing Requirements for Equipment Calibrations, Standardizations,
and Checks
R 65-14 (2018) Evaluating the Engineering and Environmental Suitability of Recycled
Materials
REINFORCING STEEL AND WIRE ROPE
M 30-15 Metallic-Coated Steel Wire Rope and Fittings for Highway Guardrail
M 31M/M 31-17 Deformed and Plain Carbon and Low-Alloy Steel Bars for Concrete
Reinforcement
M 54M/M 54-07 (2017) Welded Deformed Steel Bar Mats for Concrete Reinforcement
M 203M/M 203-12 (2016) Steel Strand, Low-Relaxation Uncoated Seven-Wire for Concrete
Reinforcement
M 204M/M 204-14 (2018) Uncoated Stress-Relieved Steel Wire for Prestressed Concrete
M 254-06 (2015) Corrosion-Resistant Coated Dowel Bars

M 275M/M 275-08 (2016) Uncoated High-Strength Steel Bars for Prestressing Concrete
M 322M/M 322-10 (2015) Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement
M 329M/M 329-11 (2015) Stainless Clad Deformed and Plain Round Steel Bars for Concrete
Reinforcement
SOILS AND STABILIZATION
M 57-80 (2017) Materials for Embankments and Subgrades

M 145-91 (2017) Classification of Soils and Soil–Aggregate Mixtures for Highway
Construction Purposes
M 146-91 (2017) Terms Relating to Subgrade, Soil–Aggregate, and Fill Materials
M 147-17 Materials for Aggregate and Soil–Aggregate Subbase, Base, and Surface
Courses
M 216-13 (2017) Quicklime and Hydrated Lime for Soil Stabilization
M 288-17 Geosynthetic Specification for Highway Applications
M 318-02 (2015) Glass Cullet Use for Soil–Aggregate Base Course
M 319-02 (2015) Reclaimed Concrete Aggregate for Unbound Soil–Aggregate Base Course
R 13-12 (2016) Conducting Geotechnical Subsurface Investigations
R 21-96 (2015) Drilling for Subsurface Investigations—Unexpectedly Encountering
Suspected Hazardous Material
R 22-97 (2015) Decommissioning Geotechnical Exploratory Boreholes
R 27-01 (2015) Assessment of Corrosion of Steel Piling for Non-Marine Applications
R 51-13 (2017) Compost for Erosion/Sediment Control (Filter Berms and Filter Socks)
R 52-10 (2015) Compost for Erosion/Sediment Control (Compost Blankets)
R 58-11 (2015) Dry Preparation of Disturbed Soil and Soil–Aggregate Samples for Test
R 69-15 Determination of Long-Term Strength for Geosynthetic Reinforcement
R 74-16 Wet Preparation of Disturbed Soil Samples for Test
R 75-16 Developing a Family of Curves
TESTING EQUIPMENT
M 152M/M 152-16 Flow Table for Use in Tests of Hydraulic Cement
M 201-15 Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks
Used in the Testing of Hydraulic Cements and Concretes
M 231-95 (2015) Weighing Devices Used in the Testing of Materials
M 261-18 Rib-Tread Standard Tire for Special-Purpose Pavement Frictional-Property
Tests
M 286-18 Smooth-Tread Standard Tire for Special-Purpose Pavement Frictional-
Property Tests
R 32-19 Calibrating the Load Cell and Deflection Sensors for a Falling Weight
Deflectometer
R 33-11 (2019) Calibrating the Reference Load Cell Used for Reference Calibrations for a
Falling Weight Deflectometer
R 45-13 (2017) Installing, Monitoring, and Processing Data of the Traveling Type Slope
Inclinometer
TIMBER AND PRESERVATIVES
M 133-12 (2016) Preservatives and Pressure Treatment Processes for Timber

M 168-07 (2016) Wood Products
DELETED STANDARDS
M 32M/M 32-09 (2013) Steel Wire, Plain, for Concrete Reinforcement

M 55M/M 55-09 (2013) Steel Welded Wire Reinforcement, Plain, for Concrete
M 221M/M 221-09 (2013) Steel Welded Wire Reinforcement, Deformed, for Concrete
M 225M/M 225-09 (2013) Steel Wire, Deformed, for Concrete Reinforcement
R 16-04 (2016) Regulatory Information for Chemicals Used in AASHTO Tests
R 48-10 (2013) Determining Rut Depth in Pavements
R 55-10 (2013) Quantifying Cracks in Asphalt Pavement Surfaces
PART 1—STANDARD SPECIFICATIONS AND STANDARD PRACTICES
NUMERICAL SEQUENCE TABLE OF CONTENTS
Number Title
M 6-13 (2018) Fine Aggregate for Hydraulic Cement Concrete
M 17-11 (2015) Mineral Filler for Bituminous Paving Mixtures
M 29-12 (2016) Fine Aggregate for Bituminous Paving Mixtures
M 30-15 Metallic-Coated Steel Wire Rope and Fittings for Highway Guardrail
M 31M/M 31-17 Deformed and Plain Carbon and Low-Alloy Steel Bars for
Concrete Reinforcement
M 33-99 (2016) Preformed Expansion Joint Filler for Concrete (Bituminous Type)
M 36-16 Corrugated Steel Pipe, Metallic-Coated, for Sewers and Drains
M 43-05 (2013) Sizes of Aggregate for Road and Bridge Construction
M 45-16 Aggregate for Masonry Mortar
M 54M/M 54-07 (2017) Welded Deformed Steel Bar Mats for Concrete Reinforcement
M 57-80 (2017) Materials for Embankments and Subgrades

M 80-13 (2017) Coarse Aggregate for Hydraulic Cement Concrete
M 81-92 (2017) Cutback Asphalt (Rapid-Curing Type)
M 82-17 Cutback Asphalt (Medium-Curing Type)
M 85-19 Portland Cement
M 86M/M 86-17 Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe
M 102M/M 102-06 (2016) Steel Forgings, Carbon and Alloy, for General Industrial Use
M 103M/M 103-12 (2016) Steel Castings, Carbon, for General Application
M 105-09 (2018) Gray Iron Castings
M 111M/M 111-15 Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
M 133-12 (2016) Preservatives and Pressure Treatment Processes for Timber
M 140-18 Emulsified Asphalt
M 143-14 (2018) Sodium Chloride
M 144-14 (2018) Calcium Chloride
M 145-91 (2017) Classification of Soils and Soil–Aggregate Mixtures for Highway
Construction Purposes
M 146-91 (2017) Terms Relating to Subgrade, Soil–Aggregate, and Fill Materials
M 147-17 Materials for Aggregate and Soil–Aggregate Subbase, Base, and Surface
Courses
M 152M/M 152-16 Flow Table for Use in Tests of Hydraulic Cement
Number Title
M 153-06 (2016) Preformed Sponge Rubber, Cork, and Recycled Rubber Expansion Joint
Fillers for Concrete Paving and Structural Construction
M 154M/M 154-12 (2016) Air-Entraining Admixtures for Concrete
M 156-13 (2017) Requirements for Mixing Plants for Hot-Mixed, Hot-Laid Bituminous Paving
Mixtures
M 157-13 (2017) Ready-Mixed Concrete
M 163M/M 163-07 (2016) Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for
General Application
M 167M/M 167-17 Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-
Arches, and Arches
M 168-07 (2016) Wood Products
M 169-15 Steel Bars, Carbon and Alloy, Cold-Finished
M 170-17 Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
M 170M-17 Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe [Metric]
M 175M/M 175-05 (2013) Perforated Concrete Pipe
M 176M/M 176-17 Porous Concrete Pipe
M 178M/M 178-17 Concrete Drain Tile
M 180-12 (2017) Corrugated Sheet Steel Beams for Highway Guardrail
M 181-10 (2015) Chain-Link Fence
M 182-05 (2017) Burlap Cloth Made from Jute or Kenaf and Cotton Mats
M 190-04 (2017) Asphalt-Coated Corrugated Metal Culvert Pipe and Pipe-Arches
M 194M/M 194-13 (2017) Chemical Admixtures for Concrete
M 195-11 (2015) Lightweight Aggregates for Structural Concrete
M 196-16 Corrugated Aluminum Pipe for Sewers and Drains
M 197-06 (2016) Aluminum Alloy Sheet for Corrugated Aluminum Pipe
M 199M/M 199-17 Precast Reinforced Concrete Manhole Sections
M 201-15 Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks
Used in the Testing of Hydraulic Cements and Concretes
M 202M/M 202-08 (2016) Steel Sheet Piling
M 203M/M 203-12 (2016) Steel Strand, Low-Relaxation Uncoated Seven-Wire for Concrete
Reinforcement
M 204M/M 204-14 (2018) Uncoated Stress-Relieved Steel Wire for Prestressed Concrete
M 205M/M 205-11 (2019) Molds for Forming Concrete Test Cylinders Vertically
M 206M/M 206-17 Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe
M 207M/M 207-17 Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe
M 208-18 Cationic Emulsified Asphalt
M 213-01 (2015) Preformed Expansion Joint Fillers for Concrete Paving and Structural
Construction (Nonextruding and Resilient Bituminous Types)
Number Title
M 216-13 (2017) Quicklime and Hydrated Lime for Soil Stabilization
M 218-03 (2016) Steel Sheet, Zinc-Coated (Galvanized), for Corrugated Steel Pipe
M 219-92 (2017) Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe,
M 224-91 (2019) Use of Protective Sealers for Portland Cement Concrete
M 226-80 (2017) Viscosity-Graded Asphalt Cement

M 227M/M 227-13 (2017) Steel Bars, Carbon, Merchant Quality, Mechanical Properties
M 230-07 (2016) Expanded and Extruded Foam Board (Polystyrene)
M 231-95 (2015) Weighing Devices Used in the Testing of Materials
M 232M/M 232-10 (2015) Zinc Coating (Hot-Dip) on Iron and Steel Hardware
M 233-86 (2014) Boiled Linseed Oil Mixture for Treatment of Portland Cement Concrete
M 235M/M 235-13 (2018) Epoxy Resin Adhesives
M 237-96 (2014) Epoxy Resin Adhesives for Bonding Traffic Markers to Hardened Portland
Cement and Asphalt Concrete
M 240M/M 240-19 Blended Hydraulic Cement
M 241M/M 241-13 (2017) Concrete Made by Volumetric Batching and Continuous Mixing
M 242M/M 242-17 Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe
M 243-96 (2017) Field-Applied Coating of Corrugated Metal Structural Plate for Pipe,
M 245-16 Corrugated Steel Pipe, Polymer-Precoated, for Sewers and Drains
M 246-15 Steel Sheet, Metallic-Coated and Polymer-Precoated, for Corrugated
Steel Pipe
M 247-13 (2018) Glass Beads Used in Pavement Markings
M 249-12 (2016) White and Yellow Reflective Thermoplastic Striping Material (Solid Form)
M 251-06 (2016) Plain and Laminated Elastomeric Bridge Bearings
M 252-18 Corrugated Polyethylene Drainage Pipe
M 254-06 (2015) Corrosion-Resistant Coated Dowel Bars
M 255M/M 255-05 (2018) Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties
M 259-17 Precast Reinforced Concrete Box Sections for Culverts, Storm Drains,
and Sewers
Sewers [Metric]
M 261-18 Rib-Tread Standard Tire for Special-Purpose Pavement Frictional-Property
Tests
M 262-11 (2015) Concrete Pipe and Related Products
M 268-15 Retroreflective Sheeting for Flat and Vertical Traffic Control Applications
Number Title
M 269-96 (2018) Turnbuckles and Shackles
M 270M/M 270-15 Structural Steel for Bridges
M 273-17 Precast Reinforced Concrete Box Sections for Culverts, Storm Drains,
and Sewers with Less Than 2 ft of Cover Subjected to Highway Loadings
M 273M-17 Precast Reinforced Concrete Box Sections for Culverts, Storm Drains,
and Sewers with Less Than 0.6 m of Cover Subjected to Highway
Loadings [Metric]
M 274-87 (2017) Steel Sheet, Aluminum-Coated (Type 2), for Corrugated Steel Pipe
M 275M/M 275-08 (2016) Uncoated High-Strength Steel Bars for Prestressing Concrete
M 277-06 (2015) Wire Rope and Sockets for Movable Bridges
M 278-15 Class PS46 Poly(Vinyl Chloride) (PVC) Pipe
M 279-14 (2018) Metallic-Coated, Steel Woven Wire Fence Fabric
M 280-14 (2018) Metallic-Coated (Carbon) Steel Barbed Wire
M 281-96 (2018) Steel Fence Posts and Assemblies, Hot-Wrought
M 285M/M 285-11 (2015) Castings, Iron-Chromium-Nickel, Corrosion Resistant, for Severe Service
M 286-18 Smooth-Tread Standard Tire for Special-Purpose Pavement Frictional-
Property Tests
M 288-17 Geosynthetic Specification for Highway Applications
M 289-91 (2017) Aluminum-Zinc Alloy Coated Sheet Steel for Corrugated Steel Pipe
M 290-96 (2018) Acrylic Prismatic Reflectors and Embossed Aluminum Frames for Signs
M 292M/M 292-15 Carbon and Alloy Steel Nuts for Bolts for High-Pressure or High-
Temperature Service, or Both
M 294-18 Corrugated Polyethylene Pipe, 300- to 1500-mm (12- to 60-in.) Diameter
M 295-19 Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete
M 297-10 (2015) Preformed Polychloroprene Elastomeric Joint Seals for Bridges
M 300-03 (2017) Inorganic Zinc-Rich Primer
M 302-19 Slag Cement for Use in Concrete and Mortars
M 303-89 (2019) Lime for Asphalt Mixtures
M 304-11 (2015) Poly(Vinyl Chloride) (PVC) Profile Wall Drain Pipe and Fittings Based on
Controlled Inside Diameter
M 306-10 (2015) Drainage, Sewer, Utility, and Related Castings
M 307-13 (2017) Silica Fume Used in Cementitious Mixtures
M 314-90 (2018) Steel Anchor Bolts
M 316-18 Polymer-Modified Emulsified Asphalt
M 318-02 (2015) Glass Cullet Use for Soil–Aggregate Base Course
M 319-02 (2015) Reclaimed Concrete Aggregate for Unbound Soil–Aggregate Base Course
M 320-17 Performance-Graded Asphalt Binder
Number Title
M 321-04 (2017) High-Reactivity Pozzolans for Use in Hydraulic-Cement Concrete, Mortar,
and Grout
M 322M/M 322-10 (2015) Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement
M 323-17 Superpave Volumetric Mix Design
M 325-08 (2017) Stone Matrix Asphalt (SMA)
M 326-18 Polyethylene (PE) Liner Pipe, 300- to 1600-mm Diameter, Based on
Controlled Outside Diameter
M 327-19 Processing Additions for Use in the Manufacture of Hydraulic Cements
M 328-14 (2018) Inertial Profiler
M 329M/M 329-11 (2015) Stainless Clad Deformed and Plain Round Steel Bars for Concrete
Reinforcement
M 330-18 Polypropylene Pipe, 300- to 1500-mm (12- to 60-in.) Diameter
M 331-17 Smoothness of Pavement in Weigh-in-Motion (WIM) Systems
M 332-18 Performance-Graded Asphalt Binder Using Multiple Stress Creep Recovery
(MSCR) Test
M 333-16 Detectable Warning Surfaces
M 334M/M 334-17 Uncoated, Corrosion-Resistant, Deformed and Plain Chromium Alloyed,
Billet-Steel Bars for Concrete Reinforcement and Dowels
M 335-18 Steel-Reinforced Polyethylene (PE) Ribbed Pipe, 300- to 1500-mm (12- to
60-in.) Diameter
M 336M/M336-18 Steel Wire and Welded Wire, Plain and Deformed, for Concrete
Reinforcement
R 5-17 Selection and Use of Emulsified Asphalts
R 8-96 (2015) Evaluation of Transportation-Related Earthborne Vibrations
R 9-05 (2018) Acceptance Sampling Plans for Highway Construction
R 10-06 (2016) Definition of Terms Related to Quality and Statistics as Used in Highway
Construction
R 13-12 (2016) Conducting Geotechnical Subsurface Investigations
R 15-18 Asphalt Additives and Modifiers
R 18-18 Establishing and Implementing a Quality Management System for

Construction Materials Testing Laboratories
R 20-99 (2017) Procedures for Measuring Highway Noise
R 21-96 (2015) Drilling for Subsurface Investigations—Unexpectedly Encountering
Suspected Hazardous Material
R 22-97 (2015) Decommissioning Geotechnical Exploratory Boreholes
R 23-99 (2018) Chemical, Biological, and Physical Analysis of Water
R 24-99 (2018) Collection and Preservation of Water Samples
R 25-19 Technician Training and Certification Programs
Number Title
R 26-01 (2018) Certifying Suppliers of Performance-Graded Asphalt Binders
R 27-01 (2015) Assessment of Corrosion of Steel Piling for Non-Marine Applications
R 28-12 (2016) Accelerated Aging of Asphalt Binder Using a Pressurized Aging
Vessel (PAV)
R 31-09 (2014) Evaluation of Protective Coating Systems for Structural Steel
R 32-19 Calibrating the Load Cell and Deflection Sensors for a Falling Weight
Deflectometer
R 33-11 (2019) Calibrating the Reference Load Cell Used for Reference Calibrations for a
R 34-03 (2018) Evaluating Deicing Chemicals
R 35-17 Superpave Volumetric Design for Asphalt Mixtures
R 36-17 Evaluating Faulting of Concrete Pavements
R 37-04 (2018) Application of Ground Penetrating Radar (GPR) to Highways
R 38-10 (2018) Quality Assurance of Standard Manufactured Materials
R 39-19 Making and Curing Concrete Test Specimens in the Laboratory
R 40-10 (2018) Measuring Pavement Profile Using a Rod and Level
R 41-05 (2015) Discontinued—Measuring Pavement Profile Using a Dipstick®
R 42-06 (2016) Developing a Quality Assurance Plan for Hot Mix Asphalt (HMA)
R 43-13 (2017) Quantifying Roughness of Pavements
R 44-07 (2018) Independent Assurance (IA) Programs
R 45-13 (2017) Installing, Monitoring, and Processing Data of the Traveling Type Slope
Inclinometer
R 46-08 (2017) Designing Stone Matrix Asphalt (SMA)
R 47-14 (2018) Reducing Samples of Hot Mix Asphalt (HMA) to Testing Size
R 49-09 (2018) Determination of Low-Temperature Performance Grade (PG) of Asphalt

Binders
R 50-09 (2018) Geosynthetic Reinforcement of the Aggregate Base Course of Flexible
Pavement Structures
R 51-13 (2017) Compost for Erosion/Sediment Control (Filter Berms and Filter Socks)
R 52-10 (2015) Compost for Erosion/Sediment Control (Compost Blankets)
R 54-14 (2018) Accepting Pavement Ride Quality When Measured Using Inertial Profiling
Systems
R 56-14 (2018) Certification of Inertial Profiling Systems

R 57-14 (2018) Operating Inertial Profiling Systems
Number Title
R 58-11 (2015) Dry Preparation of Disturbed Soil and Soil–Aggregate Samples for Test
R 59-11 (2015) Recovery of Asphalt Binder from Solution by Abson Method
R 60-12 (2016) Sampling Freshly Mixed Concrete
R 61-12 (2016) Establishing Requirements for Equipment Calibrations, Standardizations, and
Checks
R 62-13 (2017) Developing Dynamic Modulus Master Curves for Asphalt Mixtures
R 63-13 (2017) Solid Wall High-Density Polyethylene (HDPE) Conduit for Non-Pressure
Applications Used for the Protection of Power and Communications Cables
R 64-17 Sampling and Fabrication of 50-mm (2-in.) Cube Specimens Using Grout
(Non-Shrink) or Mortar
R 65-14 (2018) Evaluating the Engineering and Environmental Suitability of Recycled
Materials
R 66-16 Sampling Asphalt Mixtures
R 67-16 Sampling Asphalt Mixtures after Compaction (Obtaining Cores)
R 68-15 Preparation of Asphalt Mixtures by Means of the Marshall Apparatus
R 69-15 Determination of Long-Term Strength for Geosynthetic Reinforcement
R 70M/R 70-18 Use of Apparatus for the Determination of Length Change of Hardened
Cement Paste, Mortar, and Concrete
R 71-16 Sampling and Amount of Testing of Hydraulic Cement
R 72-16 Match Curing of Concrete Test Specimens
R 73-16 Evaluation of Precast Concrete Drainage Products
R 74-16 Wet Preparation of Disturbed Soil Samples for Test
R 75-16 Developing a Family of Curves
R 76-16 Reducing Samples of Aggregate to Testing Size
R 77-16 Certifying Suppliers of Emulsified Asphalt
R 78-16 Recovering Residue from Emulsified Asphalt Using Low-Temperature
Evaporative Techniques
R 79-16 Vacuum Drying Compacted Asphalt Specimens
R 80-17 Determining the Reactivity of Concrete Aggregates and Selecting
Appropriate Measures for Preventing Deleterious Expansion in New
Concrete Construction
R 81-17 Static Segregation of Hardened Self-Consolidating Concrete (SCC)
Cylinders
R 82-17 Pipe Joint Selection for Highway Culvert and Storm Drains
R 83-17 Preparation of Cylindrical Performance Test Specimens Using the Superpave
Gyratory Compactor (SGC)
R 84-17 Developing Dynamic Modulus Master Curves for Asphalt Mixtures Using
the Asphalt Mixture Performance Tester (AMPT)
Number Title
R 85-18 Quantifying Cracks in Asphalt Pavement Surfaces from Collected Pavement
Images Utilizing Automated Methods
R 86-18 Collecting Images of Pavement Surfaces for Distress Detection
R 87-18 Determining Pavement Deformation Parameters and Cross Slope from
Collected Transverse Profiles
R 88-18 Collecting the Transverse Pavement Profile
R 89-18 Accreditation Bodies Operating in the Fields of Construction Materials
Testing and Inspection
R 90-18 Sampling Aggregate Products
R 91-18 Determining Aggregate Source Shape Values from Digital Image Analysis
Shape Properties
R 92-18 Evaluating the Elastic Behavior of Asphalt Binders Using the Multiple Stress
DELETED STANDARDS
M 32M/M 32-09 (2013) Steel Wire, Plain, for Concrete Reinforcement

M 55M/M 55-09 (2013) Steel Welded Wire Reinforcement, Plain, for Concrete
M 221M/M 221-09 (2013) Steel Welded Wire Reinforcement, Deformed, for Concrete
M 225M/M 225-09 (2013) Steel Wire, Deformed, for Concrete Reinforcement
R 16-04 (2016) Regulatory Information for Chemicals Used in AASHTO Tests
R 48-10 (2013) Determining Rut Depth in Pavements
R 55-10 (2013) Quantifying Cracks in Asphalt Pavement Surfaces
LIST OF TECHNICAL CHANGES—PART 1
The balloted technical changes listed below are also indicated in the specifications by a change bar in the left margin and by highlighted text (for additions)
or struck-through text (for deletions). Unballoted editorial changes do not receive the change bar, highlighting, or strike-through; however, any standard that is
neither revised nor reconfirmed but contains such changes does include an endnote stating that minor editorial revisions have been made.
Release: Group 1 (April 2019)

Technical
Subcommittee
Designation Number Title Number Balloted Revisions
M 85-19 Portland Cement 3a Replaced low-alkali definition, modified heat of
hydration requirements, and removed reference to
T 98M/T 98.
M 205M/M 205-11 (2019) Molds for Forming Concrete Test Cylinders Vertically 3b Reconfirmed for 2019 publication.
M 224-91 (2019) Use of Protective Sealers for Portland Cement Concrete 5b Reconfirmed for 2019 publication.
M 240M/M 240-19 Blended Hydraulic Cement 3a Removed completion of Option R; revised Type
MH and LH heat of hydration provisions; removed
Sections 9.3 and 11.1.13; and removed referenced
information in Table 4.
M 295-19 Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in 3b Revised to maintain equivalency with ASTM
Concrete C618.
M 302-19 Slag Cement for Use in Concrete and Mortars 3b Revised to maintain equivalency with ASTM
C989/C989M.
M 303-89 (2019) Lime for Asphalt Mixtures 3a Reconfirmed for 2019 publication.
M 327-19 Processing Additions for Use in the Manufacture of Hydraulic 3c Modified fineness requirement for companion
Cements cements.
R 25-19 Technician Training and Certification Programs 5c Revised extensively.
R 32-19 Calibrating the Load Cell and Deflection Sensors for a Falling 5a Increased recertification period for FWD operators
Weight Deflectometer from one year to two years; changed “annual
calibration” to “reference calibration.”
R 33-11 (2019) Calibrating the Reference Load Cell Used for Reference 5a Reconfirmed for 2019 publication.
Calibrations for a Falling Weight Deflectometer
Technical
Subcommittee
R 39-19 Making and Curing Concrete Test Specimens in the Laboratory 3b Revised extensively.
R 41-05 (2015) Measuring Pavement Profile Using a Dipstick® 5a Discontinued because faster, equally accurate
reference profilers are now available and widely
used. See R 56 for current reference profiler
guidance.
PART 2—STANDARD TESTS
Number Title
AGGREGATES
T 11-05 (2018) Materials Finer Than 75-μm (No. 200) Sieve in Mineral Aggregates
by Washing
T 19M/T 19-14 (2018) Bulk Density (“Unit Weight”) and Voids in Aggregate
T 21M/T 21-15 Organic Impurities in Fine Aggregates for Concrete
T 27-14 (2018) Sieve Analysis of Fine and Coarse Aggregates
T 30-15 Mechanical Analysis of Extracted Aggregate
T 37-07 (2016) Sieve Analysis of Mineral Filler for Hot Mix Asphalt (HMA)
T 71-08 (2017) Effect of Organic Impurities in Fine Aggregate on Strength of Mortar
T 84-13 (2017) Specific Gravity and Absorption of Fine Aggregate
T 85-14 (2018) Specific Gravity and Absorption of Coarse Aggregate
T 96-02 (2015) Resistance to Degradation of Small-Size Coarse Aggregate by
Abrasion and Impact in the Los Angeles Machine
T 103-08 (2017) Soundness of Aggregates by Freezing and Thawing
T 104-99 (2016) Soundness of Aggregate by Use of Sodium Sulfate or
Magnesium Sulfate
T 112-00 (2017) Clay Lumps and Friable Particles in Aggregate
T 113-18 Lightweight Pieces in Aggregate
T 210-15 Aggregate Durability Index
T 255-00 (2017) Total Evaporable Moisture Content of Aggregate by Drying
T 279-18 Accelerated Polishing of Aggregates Using the British Wheel
T 304-17 Uncompacted Void Content of Fine Aggregate
T 326-05 (2018) Uncompacted Void Content of Coarse Aggregate (As Influenced by
Particle Shape, Surface Texture, and Grading)
T 327-12 (2016) Resistance of Coarse Aggregate to Degradation by Abrasion in the
Micro-Deval Apparatus
T 330-07 (2015) The Qualitative Detection of Harmful Clays of the Smectite Group in
Aggregates Using Methylene Blue
T 335-09 (2018) Determining the Percentage of Fracture in Coarse Aggregate
T 354-17 Specific Gravity and Absorption of Aggregate by Volumetric Immersion
Method
T 380-19 Potential Alkali Reactivity of Aggregates and Effectiveness of ASR
Mitigation Measures (Miniature Concrete Prism Test, MCPT)
T 381-18 Determining Aggregate Shape Properties by Means of Digital Image
Analysis
Number Title
T 44-14 (2018) Solubility of Bituminous Materials
T 48-18 Flash Fire Point of Asphalt Binder by Cleveland Open Cup
T 49-15 Penetration of Bituminous Materials
T 50-14 (2018) Float Test for Bituminous Materials
T 51-09 (2018) Ductility of Asphalt Materials
T 53-09 (2018) Softening Point of Bitumen (Ring-and-Ball Apparatus)
T 59-16 Emulsified Asphalts
T 72-10 (2015) Saybolt Viscosity
T 78-15 Distillation of Cutback Asphalt Products
T 79-12 (2016) Flash Point with Tag Open-Cup Apparatus for Use with Material
Having a Flash Point Less Than 93ºC (200ºF)
T 102-09 (2018) Spot Test of Asphaltic Materials
T 110-03 (2016) Moisture or Volatile Distillates in Hot Mix Asphalt (HMA)
T 111-11 (2015) Mineral Matter or Ash in Asphalt Materials
T 164-14 (2018) Quantitative Extraction of Asphalt Binder from Hot Mix Asphalt (HMA)
T 166-16 Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using
Saturated Surface-Dry Specimens
T 167-10 (2015) Compressive Strength of Hot Mix Asphalt
T 168-03 (2016) Sampling Bituminous Paving Mixtures
T 179-05 (2018) Effect of Heat and Air on Asphalt Materials (Thin-Film Oven Test)
T 195-18 Determining Degree of Particle Coating of Asphalt Mixtures
T 201-15 Kinematic Viscosity of Asphalts (Bitumens)
T 202-15 Viscosity of Asphalts by Vacuum Capillary Viscometer
T 209-12 (2016) Theoretical Maximum Specific Gravity (Gmm) and Density of Hot Mix
Asphalt (HMA)
T 228-09 (2018) Specific Gravity of Semi-Solid Asphalt Materials
T 240-13 (2017) Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling
Thin-Film Oven Test)
T 245-15 Resistance to Plastic Flow of Asphalt Mixtures Using
Marshall Apparatus
T 246-10 (2015) Resistance to Deformation and Cohesion of Hot Mix Asphalt (HMA)
by Means of Hveem Apparatus
T 247-10 (2015) Preparation of Test Specimens of Hot Mix Asphalt (HMA) by Means
of California Kneading Compactor
T 269-14 (2018) Percent Air Voids in Compacted Dense and Open Asphalt Mixtures
T 275-17 Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using
Paraffin-Coated Specimens
T 283-14 (2018) Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage
T 287-14 (2018) Asphalt Binder Content of Asphalt Mixtures by the Nuclear Method
T 295-13 (2017) Specific Gravity or API Gravity of Liquid Asphalts by
Hydrometer Method
Number Title
T 300-11 (2016) Force Ductility Test of Asphalt Materials
T 301-13 (2017) Elastic Recovery Test of Asphalt Materials by Means of a Ductilometer
T 302-15 Polymer Content of Polymer-Modified Emulsified Asphalt Residue
and Asphalt Binders
T 305-14 (2018) Determination of Draindown Characteristics in Uncompacted Asphalt
Mixtures
T 308-18 Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA)
by the Ignition Method
T 312-15 Preparing and Determining the Density of Asphalt Mixture Specimens
by Means of the Superpave Gyratory Compactor
T 313-12 (2016) Determining the Flexural Creep Stiffness of Asphalt Binder Using
the Bending Beam Rheometer (BBR)
T 314-12 (2016) Determining the Fracture Properties of Asphalt Binder in Direct Tension
(DT)
T 315-12 (2016) Determining the Rheological Properties of Asphalt Binder Using a
Dynamic Shear Rheometer (DSR)
T 316-13 (2017) Viscosity Determination of Asphalt Binder Using Rotational Viscometer
T 319-15 Quantitative Extraction and Recovery of Asphalt Binder from
Asphalt Mixtures
T 320-07 (2016) Determining the Permanent Shear Strain and Stiffness of Asphalt
Mixtures Using the Superpave Shear Tester (SST)
T 321-17 Determining the Fatigue Life of Compacted Asphalt Mixtures Subjected
to Repeated Flexural Bending
T 322-07 (2016) Determining the Creep Compliance and Strength of Hot Mix Asphalt
(HMA) Using the Indirect Tensile Test Device
T 324-17 Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures
T 329-15 Moisture Content of Ashpalt Mixtures by Oven Method
T 331-13 (2017) Bulk Specific Gravity (Gmb) and Density of Compacted Asphalt Mixtures
Using Automatic Vacuum Sealing Method
T 340-10 (2015) Determining Rutting Susceptibility of Hot Mix Asphalt (HMA) Using the
Asphalt Pavement Analyzer (APA)
T 342-11 (2015) Determining Dynamic Modulus of Hot Mix Asphalt (HMA)
T 343-12 (2016) Density of In-Place Hot Mix Asphalt (HMA) Pavement by Electronic
Surface Contact Devices
T 344-12 (2016) Evaluation of Superpave Gyratory Compactor (SGC) Internal Angle of
Gyration Using Simulated Loading
T 350-14 (2018) Multiple Stress Creep Recover (MSCR) Test of Asphalt Binder Using a
T 355-18 In-Place Density of Asphalt Mixtures by Nuclear Methods
T 361-16 Determining Asphalt Binder Bond Strength by Means of the Binder
Bond Strength (BBS) Test
T 362-17 Quantitative Determination of the Percentage of Lime in Asphalt
Mixtures
Number Title
T 377-17 Detecting the Presence of Phosphorus in Asphalt Binder
T 378-17 Determining the Dynamic Modulus and Flow Number for Asphalt
Mixtures Using the Asphalt Mixture Performance Tester (AMPT)
T 382-18 Determining the Viscosity of Emulsified Asphalt by a Rotational Paddle
Viscometer
T 383-18 Evaluation of Asphalt Release Agents (ARAs)
BOX CULVERT, CULVERT PIPE, AND DRAIN PIPE

T 241-95 (2017) Helical Continuously Welded Seam Corrugated Steel Pipe
T 249-03 (2016) Helical Lock Seam Corrugated Pipe
T 280-14 (2018) Concrete Pipe, Manhole Sections, or Tile
T 281-14 (2018) Vitrified Clay Pipe
T 341-10 (2014) Determination of Compression Capacity for Profile Wall Plastic
Pipe by Stub Compression Loading
CONCRETE, CURING MATERIALS, AND ADMIXTURES

T 22-17 Compressive Strength of Cylindrical Concrete Specimens
T 23-18 Making and Curing Concrete Test Specimens in the Field
T 24M/T 24-15 (2019) Obtaining and Testing Drilled Cores and Sawed Beams of Concrete
T 97-18 Flexural Strength of Concrete (Using Simple Beam with Third-Point
Loading)
T 119M/T 119-18 Slump of Hydraulic Cement Concrete
T 121M/T 121-19 Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
T 140-97 (2016) Compressive Strength of Concrete Using Portions of Beams Broken
in Flexure
T 148-15 (2019) Measuring Length of Drilled Concrete Cores
T 152-19 Air Content of Freshly Mixed Concrete by the Pressure Method
T 155-13 (2017) Water Retention by Liquid Membrane-Forming Curing Compounds
for Concrete
T 157-12 (2016) Air-Entraining Admixtures for Concrete
T 158-11 (2019) Bleeding of Concrete
T 160-17 Length Change of Hardened Hydraulic Cement Mortar and Concrete
T 161-17 Resistance of Concrete to Rapid Freezing and Thawing
T 177-17 Flexural Strength of Concrete (Using Simple Beam with Center-Point
Loading)
T 178-15 (2019) Portland-Cement Content of Hardened Hydraulic-Cement Concrete
T 196M/T 196-11 (2019) Air Content of Freshly Mixed Concrete by the Volumetric Method
T 197M/T 197-11 (2019) Time of Setting of Concrete Mixtures by Penetration Resistance
T 198-15 (2019) Splitting Tensile Strength of Cylindrical Concrete Specimens
T 231-17 Capping Cylindrical Concrete Specimens
Number Title
T 253-02 (2016) Coated Dowel Bars
T 259-02 (2017) Resistance of Concrete to Chloride Ion Penetration
T 260-97 (2016) Sampling and Testing for Chloride Ion in Concrete and Concrete Raw
Materials
T 276-17 Measuring Early-Age Compression Strength and Projecting Later-Age
Strength
T 277-15 (2019) Electrical Indication of Concrete’s Ability to Resist Chloride Ion
Penetration
T 285-89 (2015) Bend Test for Bars for Concrete Reinforcement
T 303-00 (2017) Accelerated Detection of Potentially Deleterious Expansion of Mortar
Bars Due to Alkali–Silica Reaction
T 309-15 (2019) Temperature of Freshly Mixed Portland Cement Concrete
T 318-15 (2019) Water Content of Freshly Mixed Concrete Using Microwave Oven
Drying
T 325-04 (2016) Estimating the Strength of Concrete in Transportation Construction
by Maturity Tests
T 332-07 (2016) Determining Chloride Ions in Concrete and Concrete Materials by
Specific
Ion Probe
T 334-08 (2016) Estimating the Cracking Tendency of Concrete
T 336-15 (2019) Coefficient of Thermal Expansion of Hydraulic Cement Concrete
T 345-12 (2016) Passing Ability of Self-Consolidating Concrete (SCC) by J-Ring
T 347-13 (2017) Slump Flow of Self-Consolidating Concrete (SCC)
T 348-13 (2018) Air-Void Characteristics of Freshly Mixed Concrete by Buoyancy
Change
T 349-13 (2017) Filling Capacity of Self-Consolidating Concrete Using the Caisson Test
T 351-14 (2018) Visual Stability Index (VSI) of Self-Consolidating Concrete (SCC)
T 352-14 (2018) Determining Formwork Pressure of Fresh Self-Consolidating Concrete
(SCC) Using Pressure Transducers
T 356-15 (2019) Determining Air Content of Hardened Portland Cement Concrete by
High-Pressure Air Meter
T 357-15 (2019) Predicting Chloride Penetration of Hydraulic Cement Concrete by the
Rapid Migration Procedure
T 358-19 Surface Resistivity Indication of Concrete’s Ability to Resist Chloride
Ion Penetration
T 359M/T 359-18 Pavement Thickness by Magnetic Pulse Induction
T 363-17 Evaluating Stress Development and Cracking Potential due to Restrained
Volume Change Using a Dual Ring Test
T 364-17 Determination of Composite Activation Energy of Aggregates due to
Alkali-Silica Reaction (Chemical Method)
T 365-17 Quantifying Calcium Oxychloride Amounts in Cement Pastes Exposed to
Deicing Salts
T 373M/T 373-17 Comparative Qualitative Corrosion Characterization of Steel Bars Used
for Concrete Reinforcement (Linear Polarization Resistance and
Potentiodynamic Polarization Tests)
Number Title
T 374M/T 374-17 Comparative Qualitative Corrosion Characterization of Uncoated
Chromium-Alloyed Steel Bars Used for Concrete Reinforcement
(Tombstone Test)
T 375M/T 375-17 Identification of Iron-Based Alloy Steel Bars for Concrete Reinforcement
or Dowels by Handheld X-Ray Fluorescence (XRF) Spectrometer
T 376M/T 376-17 Macrocell Slab Chloride Threshold
T 379-18 Nonlinear Impact Resonance Acoustic Spectroscopy (NIRAS) for
Concrete Specimens with Damage from Alkali-Silica Reaction (ASR)
HYDRAULIC CEMENT
T 98M/T 98-12 (2016) Fineness of Portland Cement by the Turbidimeter
T 105-16 Chemical Analysis of Hydraulic Cement
T 106M/T 106-18 Compressive Strength of Hydraulic Cement Mortar (Using 50-mm or 2-
in. Cube Specimens)
T 107M/T 107-18 Autoclave Expansion of Hydraulic Cement
T 129-14 (2018) Amount of Water Required for Normal Consistency of Hydraulic Cement
Paste
T 131-15 Time of Setting of Hydraulic Cement by Vicat Needle
T 132-87 (2018) Tensile Strength of Hydraulic Cement Mortars
T 133-19 Density of Hydraulic Cement
T 137-12 (2016) Air Content of Hydraulic Cement Mortar
T 153-13 (2017) Fineness of Hydraulic Cement by Air Permeability Apparatus
T 154-18 Time of Setting of Hydraulic Cement by Gillmore Needles
T 162-16 Mechanical Mixing of Hydraulic Cement Pastes and Mortars of
Plastic Consistency
T 185-15 Early Stiffening of Hydraulic Cement (Mortar Method)
T 186-15 Early Stiffening of Hydraulic Cement (Paste Method)
T 188-05 (2017) Evaluation by Freezing and Thawing of Air-Entraining Additions
to Hydraulic Cement
T 192-19 Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve
T 323-03 (2016) Determining the Shear Strength at the Interface of Bonded Layers
of Portland Cement Concrete
T 353-14 (2018) Particle Size Analysis of Hydraulic Cement and Related Materials by
Light Scattering
JOINT FILLER, SEALANTS, AND ASPHALT PLANK

Number Title
Apparent Viscosity of Hot-Poured Asphalt Crack Sealant Using
T 366-18
Rotational Viscometer
Accelerated Aging of Hot-Poured Asphalt Crack Sealant Using a
T 367-17
Vacuum Oven
Measuring Low-Temperature Flexural Creep Stiffness of Hot-Poured
T 368-17
Asphalt Crack Sealant by Bending Beam Rheometer (BBR)
Evaluation of the Low-Temperature Tensile Property of Hot-Poured
T 369-17
Asphalt Crack Sealant by Direct Tension Test
Measuring Adhesion of Hot-Poured Asphalt Crack Sealant Using Direct
T 370-18
Adhesion Tester
Measuring Interfacial Fracture Energy of Hot-Poured Asphalt Crack
T 371-17
Sealant Using a Blister Test
METALLIC MATERIALS FOR BRIDGES

T 65M/T 65-13 (2017) Mass [Weight] of Coating on Iron and Steel Articles with Zinc or Zinc-
Alloy Coatings
T 213M/T 213-11 (2015) Mass [Weight] of Coating on Aluminum-Coated Iron or Steel Articles
T 243M/T 243-08 (2017) Sampling Procedure for Impact Testing of Structural Steel
T 244-18 Mechanical Testing of Steel Products
T 337-09 (2014) Non-Instrumental Determination of Metallic Zinc in Zinc-Rich Primers
T 338-09 (2014) Analysis of Structural Steel Coatings for Hindered Amine Light
Stabilizer (HALS)
T 339-10 (2015) Analysis of Structural Steel Coatings for Isocyanate Content
T 372M/T 372-17 Sensitivity of Stainless Steel to Intergranular Attack
MISCELLANEOUS
T 256-01 (2016) Pavement Deflection Measurements
T 257-96 (2018) Instrumental Photometric Measurements of Retroflective Materials and
Retroflective Devices

T 143-13 (2017) Sampling and Testing Calcium Chloride for Roads and
Structural Applications
T 237-05 (2014) Testing Epoxy Resin Adhesive
T 250-05 (2014) Thermoplastic Traffic Line Material
T 333-07 (2017) Linear Coefficient of Shrinkage on Cure of Adhesive Systems
T 346-13 (2017) Glass Beads Used in Pavement Markings
PAVEMENT SURFACE CHARACTERISTICS

T 242-18 Frictional Properties of Paved Surfaces Using a Full-Scale Tire
T 278-90 (2017) Surface Frictional Properties Using the British Pendulum Tester
T 282-01 (2019) Calibrating a Wheel Force or Torque Transducer Using a Calibration
Platform (User Level)
Number Title
T 317-04 (2018) Prediction of Asphalt-Bound Pavement Layer Temperatures
T 360-16 Measurement of Tire/Pavement Noise Using the On-Board Sound
Intensity (OBSI) Method
SOILS AND STABILIZATION

T 88-13 (2017) Particle Size Analysis of Soils
T 89-13 (2017) Determining the Liquid Limit of Soils
T 90-16 Determining the Plastic Limit and Plasticity Index of Soils
T 99-18 Moisture–Density Relations of Soils Using a 2.5-kg (5.5-lb) Rammer and
a 305-mm (12-in.) Drop
T 100-15 Specific Gravity of Soils
T 134-05 (2018) Moisture–Density Relations of Soil–Cement Mixtures
T 135-13 (2017) Wetting-and-Drying Test of Compacted Soil–Cement Mixtures
T 136-13 (2017) Freezing-and-Thawing Tests of Compacted Soil–Cement Mixtures
T 176-17 Plastic Fines in Graded Aggregates and Soils by Use of the Sand
Equivalent Test
T 180-18 Moisture–Density Relations of Soils Using a 4.54-kg (10-lb) Rammer
and a 457-mm (18-in.) Drop
T 190-14 (2018) Resistance R-Value and Expansion Pressure of Compacted Soils
T 191-14 (2018) Density of Soil In-Place by the Sand-Cone Method
T 193-13 (2017) The California Bearing Ratio
T 194-97 (2018) Determination of Organic Matter in Soils by Wet Combustion
T 206-09 (2013) Penetration Test and Split-Barrel Sampling of Soils
T 207-12 (2016) Thin-Walled Tube Sampling of Soils
T 208-15 Unconfined Compressive Strength of Cohesive Soil
T 211-90 (2017) Determination of Cement Content in Cement-Treated Aggregate
by the Method of Titration
T 215-14 (2018) Permeability of Granular Soils (Constant Head)
T 216-07 (2016) One-Dimensional Consolidation Properties of Soils
T 217-14 (2018) Determination of Moisture in Soils by Means of a Calcium Carbide Gas
Pressure Moisture Tester
T 218-86 (2018) Sampling Hydrated Lime
T 219-87 (2018) Testing Lime for Chemical Constituents and Particle Sizes
T 220-66 (2018) Determination of the Strength of Soil–Lime Mixtures
T 221-90 (2017) Repetitive Static Plate Load Tests of Soils and Flexible Pavement
Components for Use in Evaluation and Design of Airport and
Highway Pavements
T 222-81 (2017) Nonrepetitive Static Plate Load Test of Soils and Flexible Pavement
Components for Use in Evaluation and Design of Airport and Highway
Pavements
T 223-96 (2017) Field Vane Shear Test in Cohesive Soil
T 225-16 Diamond Core Drilling for Site Investigation
Number Title
T 226-90 (2018) Triaxial Compressive Strength of Undrained Rock Core Specimens
without Pore Pressure Measurements
T 232-90 (2018) Determination of Lime Content in Lime-Treated Soils by Titration
T 233-02 (2015) Density of Soil In-Place by Block, Chunk, or Core Sampling
T 236-08 (2018) Direct Shear Test of Soils under Consolidated Drained Conditions
T 252-09 (2018) Measurements of Pore Pressures in Soils
T 258-81 (2018) Determining Expansive Soils
T 265-15 Laboratory Determination of Moisture Content of Soils
T 267-86 (2018) Determination of Organic Content in Soils by Loss on Ignition
T 272-18 One-Point Method for Determining Maximum Dry Density and
Optimum Moisture
T 273-86 (2018) Soil Suction
T 288-12 (2016) Determining Minimum Laboratory Soil Resistivity
T 289-91 (2018) Determining pH of Soil for Use in Corrosion Testing
T 290-95 (2016) Determining Water-Soluble Sulfate Ion Content in Soil
T 291-94 (2018) Determining Water-Soluble Chloride Ion Content in Soil
T 296-10 (2016) Unconsolidated, Undrained Compressive Strength of Cohesive Soils in
Triaxial Compression
T 298-15 High-Strain Dynamic Testing of Piles
T 306-11 (2015) Progressing Auger Borings for Geotechnical Explorations
T 307-99 (2017) Determining the Resilient Modulus of Soils and Aggregate Materials
T 310-13 (2017) In-Place Density and Moisture Content of Soil and Soil–Aggregate
by Nuclear Methods (Shallow Depth)
T 311-00 (2015) Grain-Size Analysis of Granular Soil Materials
DELETED STANDARD
T 42-10 (2015) Preformed Expansion Joint Filler for Concrete Construction

PART 2—STANDARD TESTS
Number Title
T 11-05 (2018) Materials Finer Than 75-μm (No. 200) Sieve in Mineral Aggregates by
Washing
T 19M/T 19-14 (2018) Bulk Density (“Unit Weight”) and Voids in Aggregate
T 21M/T 21-15 Organic Impurities in Fine Aggregates for Concrete
T 22-17 Compressive Strength of Cylindrical Concrete Specimens
T 23-18 Making and Curing Concrete Test Specimens in the Field
T 24M/T 24-15 (2019) Obtaining and Testing Drilled Cores and Sawed Beams of Concrete
T 27-14 (2018) Sieve Analysis of Fine and Coarse Aggregates
T 30-15 Mechanical Analysis of Extracted Aggregate
T 37-07 (2016) Sieve Analysis of Mineral Filler for Hot Mix Asphalt (HMA)
T 44-14 (2018) Solubility of Bituminous Materials

T 48-18 Flash Fire Point of Asphalt Binder by Cleveland Open Cup
T 49-15 Penetration of Bituminous Materials
T 50-14 (2018) Float Test for Bituminous Materials
T 51-09 (2018) Ductility of Asphalt Materials
T 53-09 (2018) Softening Point of Bitumen (Ring-and-Ball Apparatus)
T 59-16 Emulsified Asphalts
T 65M/T 65-13 (2017) Mass [Weight] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy
Coatings
T 71-08 (2017) Effect of Organic Impurities in Fine Aggregate on Strength of Mortar
T 72-10 (2015) Saybolt Viscosity
T 78-15 Distillation of Cutback Asphalt Products
T 79-12 (2016) Flash Point with Tag Open-Cup Apparatus for Use with Material Having a
Flash Point Less Than 93ºC (200ºF)
T 84-13 (2017) Specific Gravity and Absorption of Fine Aggregate
T 85-14 (2018) Specific Gravity and Absorption of Coarse Aggregate
T 88-13 (2017) Particle Size Analysis of Soils
T 89-13 (2017) Determining the Liquid Limit of Soils
T 90-16 Determining the Plastic Limit and Plasticity Index of Soils
Number Title
T 96-02 (2015) Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and
Impact in the Los Angeles Machine
T 97-18 Flexural Strength of Concrete (Using Simple Beam with
Third-Point Loading)
T 98M/T 98-12 (2016) Fineness of Portland Cement by the Turbidimeter
T 99-18 Moisture–Density Relations of Soils Using a 2.5-kg (5.5-lb) Rammer
T 100-15 Specific Gravity of Soils
T 102-09 (2018) Spot Test of Asphaltic Materials
T 103-08 (2017) Soundness of Aggregates by Freezing and Thawing
T 104-99 (2016) Soundness of Aggregate by Use of Sodium Sulfate or Magnesium Sulfate
T 105-16 Chemical Analysis of Hydraulic Cement
T 106M/T 106-18 Compressive Strength of Hydraulic Cement Mortar (Using 50-mm or 2-in.
Cube Specimens)
T 107M/T 107-18 Autoclave Expansion of Hydraulic Cement
T 110-03 (2016) Moisture or Volatile Distillates in Hot Mix Asphalt (HMA)
T 111-11 (2015) Mineral Matter or Ash in Asphalt Materials
T 112-00 (2017) Clay Lumps and Friable Particles in Aggregate
T 113-18 Lightweight Pieces in Aggregate
T 119M/T 119-18 Slump of Hydraulic Cement Concrete
T 121M/T 121-19 Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
T 129-14 (2018) Amount of Water Required for Normal Consistency of Hydraulic Cement
Paste
T 131-15 Time of Setting of Hydraulic Cement by Vicat Needle
T 132-87 (2018) Tensile Strength of Hydraulic Cement Mortars
T 133-19 Density of Hydraulic Cement
T 134-05 (2018) Moisture–Density Relations of Soil–Cement Mixtures
T 135-13 (2017) Wetting-and-Drying Test of Compacted Soil–Cement Mixtures
T 136-13 (2017) Freezing-and-Thawing Tests of Compacted Soil–Cement Mixtures
T 137-12 (2016) Air Content of Hydraulic Cement Mortar
T 140-97 (2016) Compressive Strength of Concrete Using Portions of Beams Broken in Flexure
T 143-13 (2017) Sampling and Testing Calcium Chloride for Roads and Structural Applications
T 148-15 (2019) Measuring Length of Drilled Concrete Cores
T 152-19 Air Content of Freshly Mixed Concrete by the Pressure Method
T 153-13 (2017) Fineness of Hydraulic Cement by Air Permeability Apparatus
Number Title
T 154-18 Time of Setting of Hydraulic Cement Paste by Gillmore Needles
T 155-13 (2017) Water Retention by Liquid Membrane-Forming Curing Compounds
for Concrete
T 157-12 (2016) Air-Entraining Admixtures for Concrete
T 158-11 (2019) Bleeding of Concrete
T 160-17 Length Change of Hardened Hydraulic Cement Mortar and Concrete
T 161-17 Resistance of Concrete to Rapid Freezing and Thawing
T 162-16 Mechanical Mixing of Hydraulic Cement Pastes and Mortars of
Plastic Consistency
T 164-14 (2018) Quantitative Extraction of Asphalt Binder from Hot Mix Asphalt (HMA)
T 166-16 Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Saturated
Surface-Dry Specimens
T 167-10 (2015) Compressive Strength of Hot Mix Asphalt
T 168-03 (2016) Sampling Bituminous Paving Mixtures
T 176-17 Plastic Fines in Graded Aggregates and Soils by Use of the Sand
Equivalent Test
T 177-17 Flexural Strength of Concrete (Using Simple Beam with Center-Point

Loading)
T 178-15 (2019) Portland-Cement Content of Hardened Hydraulic-Cement Concrete
T 179-05 (2018) Effect of Heat and Air on Asphalt Materials (Thin-Film Oven Test)
T 180-18 Moisture–Density Relations of Soils Using a 4.54-kg (10-lb) Rammer
T 185-15 Early Stiffening of Hydraulic Cement (Mortar Method)
T 186-15 Early Stiffening of Hydraulic Cement (Paste Method)
T 188-05 (2017) Evaluation by Freezing and Thawing of Air-Entraining Additions to Hydraulic
Cement
T 190-14 (2018) Resistance R-Value and Expansion Pressure of Compacted Soils
T 191-14 (2018) Density of Soil In-Place by the Sand-Cone Method
T 192-19 Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve
T 193-13 (2017) The California Bearing Ratio
T 194-97 (2018) Determination of Organic Matter in Soils by Wet Combustion
T 195-18 Determining Degree of Particle Coating of Asphalt Mixtures
T 196M/T 196-11 (2019) Air Content of Freshly Mixed Concrete by the Volumetric Method
T 197M/T 197-11 (2019) Time of Setting of Concrete Mixtures by Penetration Resistance
T 198-15 (2019) Splitting Tensile Strength of Cylindrical Concrete Specimens
T 201-15 Kinematic Viscosity of Asphalts (Bitumens)
Number Title
T 202-15 Viscosity of Asphalts by Vacuum Capillary Viscometer
T 206-09 (2018) Penetration Test and Split-Barrel Sampling of Soils
T 207-12 (2016) Thin-Walled Tube Sampling of Soils
T 208-15 Unconfined Compressive Strength of Cohesive Soil
T 209-12 (2016) Theoretical Maximum Specific Gravity (Gmm) and Density of Hot Mix
Asphalt (HMA)
T 210-15 Aggregate Durability Index
T 211-90 (2017) Determination of Cement Content in Cement-Treated Aggregate
by the Method of Titration
T 213M/T 213-11 (2015) Mass [Weight] of Coating on Aluminum-Coated Iron or Steel Articles
T 215-14 (2018) Permeability of Granular Soils (Constant Head)

T 216-07 (2016) One-Dimensional Consolidation Properties of Soils
T 217-14 (2018) Determination of Moisture in Soils by Means of a Calcium Carbide Gas
Pressure Moisture Tester
T 218-86 (2018) Sampling Hydrated Lime
T 219-87 (2018) Testing Lime for Chemical Constituents and Particle Sizes
T 220-66 (2018) Determination of the Strength of Soil–Lime Mixtures
T 221-90 (2017) Repetitive Static Plate Load Test of Soils and Flexible Pavement
Components for Use in Evaluation and Design of Airport and
Highway Pavements
T 222-81 (2017) Nonrepetitive Static Plate Load Test of Soils and Flexible Pavement
Components for Use in Evaluation and Design of Airport and Highway
Pavements
T 223-96 (2017) Field Vane Shear Test in Cohesive Soil
T 225-16 Diamond Core Drilling for Site Investigation
T 226-90 (2018) Triaxial Compressive Strength of Undrained Rock Core Specimens without
Pore Pressure Measurements
T 228-09 (2018) Specific Gravity of Semi-Solid Asphalt Materials
T 231-17 Capping Cylindrical Concrete Specimens
T 232-90 (2018) Determination of Lime Content in Lime-Treated Soils by Titration
T 233-02 (2015) Density of Soil In-Place by Block, Chunk, or Core Sampling
T 236-08 (2018) Direct Shear Test of Soils under Consolidated Drained Conditions
T 237-05 (2014) Testing Epoxy Resin Adhesive
T 240-13 (2017) Effect of Heat and Air on a Moving Film of Asphalt Binder (Rolling Thin-
Film Oven Test)
T 241-95 (2017) Helical Continuously Welded Seam Corrugated Steel Pipe
Number Title
T 242-18 Frictional Properties of Paved Surfaces Using a Full-Scale Tire
T 243M/T 243-08 (2017) Sampling Procedure for Impact Testing of Structural Steel
T 244-18 Mechanical Testing of Steel Products
T 245-15 Resistance to Plastic Flow of Asphalt Mixtures Using Marshall Apparatus
T 246-10 (2015) Resistance to Deformation and Cohesion of Hot Mix Asphalt (HMA) by
Means of Hveem Apparatus
T 247-10 (2015) Preparation of Test Specimens of Hot Mix Asphalt (HMA) by Means of
California Kneading Compactor
T 249-03 (2016) Helical Lock Seam Corrugated Pipe
T 250-05 (2014) Thermoplastic Traffic Line Material
T 252-09 (2018) Measurements of Pore Pressures in Soils
T 253-02 (2016) Coated Dowel Bars
T 255-00 (2017) Total Evaporable Moisture Content of Aggregate by Drying
T 256-01 (2016) Pavement Deflection Measurements
T 257-96 (2018) Instrumental Photometric Measurements of Retroreflective Materials and
Retroreflective Devices
T 258-81 (2018) Determining Expansive Soils
T 259-02 (2017) Resistance of Concrete to Chloride Ion Penetration
T 260-97 (2016) Sampling and Testing for Chloride Ion in Concrete and Concrete Raw
Materials
T 265-15 Laboratory Determination of Moisture Content of Soils
T 267-86 (2018) Determination of Organic Content in Soils by Loss on Ignition
T 269-14 (2018) Percent Air Voids in Compacted Dense and Open Asphalt Mixtures
T 272-18 One-Point Method for Determining Maximum Dry Density and Optimum
Moisture
T 273-86 (2018) Soil Suction
T 275-17 Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Paraffin-
Coated Specimens
T 276-17 Measuring Early-Age Compression Strength and Projecting Later-Age
Strength
T 277-15 (2019) Electrical Indication of Concrete’s Ability to Resist Chloride Ion Penetration
T 278-90 (2017) Surface Frictional Properties Using the British Pendulum Tester
T 279-18 Accelerated Polishing of Aggregates Using the British Wheel
T 280-14 (2018) Concrete Pipe, Manhole Sections, or Tile
T 281-14 (2018) Vitrified Clay Pipe
Number Title
T 282-01 (2019) Calibrating a Wheel Force or Torque Transducer Using a Calibration Platform
(User Level)
T 283-14 (2018) Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage
T 285-89 (2015) Bend Test for Bars for Concrete Reinforcement
T 287-14 (2018) Asphalt Binder Content of Asphalt Mixtures by the Nuclear Method
T 288-12 (2016) Determining Minimum Laboratory Soil Resistivity
T 289-91 (2018) Determining pH of Soil for Use in Corrosion Testing
T 290-95 (2016) Determining Water-Soluble Sulfate Ion Content in Soil
T 291-94 (2018) Determining Water-Soluble Chloride Ion Content in Soil
T 295-13 (2017) Specific Gravity or API Gravity of Liquid Asphalts by Hydrometer Method
T 296-10 (2016) Unconsolidated, Undrained Compressive Strength of Cohesive Soils in
Triaxial Compression
T 298-15 High-Strain Dynamic Testing of Piles
T 300-11 (2016) Force Ductility Test of Asphalt Materials
T 301-13 (2017) Elastic Recovery Test of Asphalt Materials by Means of a Ductilometer
T 302-15 Polymer Content of Polymer-Modified Emulsified Asphalt Residue and
Asphalt Binders
T 303-00 (2017) Accelerated Detection of Potentially Deleterious Expansion of Mortar Bars
Due to Alkali–Silica Reaction
T 304-17 Uncompacted Void Content of Fine Aggregate
T 305-14 (2018) Determination of Draindown Characteristics in Uncompacted Asphalt
Mixtures
T 306-11 (2015) Progressing Auger Borings for Geotechnical Explorations
T 307-99 (2017) Determining the Resilient Modulus of Soils and Aggregate Materials
T 308-18 Determining the Asphalt Binder Content of Hot Mix Asphalt (HMA) by the
Ignition Method
T 309-15 (2019) Temperature of Freshly Mixed Portland Cement Concrete
T 310-13 (2017) In-Place Density and Moisture Content of Soil and Soil–Aggregate by Nuclear
Methods (Shallow Depth)
T 311-00 (2015) Grain-Size Analysis of Granular Soil Materials
T 312-15 Preparing and Determining the Density of Asphalt Mixture Specimens by
Means of the Superpave Gyratory Compactor
T 313-12 (2016) Determining the Flexural Creep Stiffness of Asphalt Binder Using the
Bending Beam Rheometer (BBR)
T 314-12 (2016) Determining the Fracture Properties of Asphalt Binder in Direct Tension (DT)
T 315-12 (2016) Determining the Rheological Properties of Asphalt Binder Using a Dynamic
Shear Rheometer (DSR)
Number Title
T 316-13 (2017) Viscosity Determination of Asphalt Binder Using Rotational Viscometer
T 317-04 (2018) Prediction of Asphalt-Bound Pavement Layer Temperatures
T 318-15 (2019) Water Content of Freshly Mixed Concrete Using Microwave Oven Drying
T 319-15 Quantitative Extraction and Recovery of Asphalt Binder from Asphalt
Mixtures
T 320-07 (2016) Determining the Permanent Shear Strain and Stiffness of Asphalt Mixtures
Using the Superpave Shear Tester (SST)
T 321-17 Determining the Fatigue Life of Compacted Asphalt Mixtures Subjected to
Repeated Flexural Bending
T 322-07 (2016) Determining the Creep Compliance and Strength of Hot Mix Asphalt (HMA)
Using the Indirect Tensile Test Device
T 323-03 (2016) Determining the Shear Strength at the Interface of Bonded Layers of Portland
Cement Concrete
T 324-17 Hamburg Wheel-Track Testing of Compacted Asphalt Mixtures
T 325-04 (2016) Estimating the Strength of Concrete in Transportation Construction by
Maturity Tests
T 326-05 (2018) Uncompacted Void Content of Coarse Aggregate (As Influenced by Particle
Shape, Surface Texture, and Grading)
T 327-12 (2016) Resistance of Coarse Aggregate to Degradation by Abrasion in the Micro-
Deval Apparatus
T 329-15 Moisture Content of Asphalt Mixtures by Oven Method
T 330-07 (2015) The Qualitative Detection of Harmful Clays of the Smectite Group in
Aggregates Using Methylene Blue
T 331-13 (2017) Bulk Specific Gravity (Gmb) and Density of Compacted Asphalt Mixtures
Using Automatic Vacuum Sealing Method
T 332-07 (2016) Determining Chloride Ions in Concrete and Concrete Materials by Specific
Ion Probe
T 333-07 (2017) Linear Coefficient of Shrinkage on Cure of Adhesive Systems
T 334-08 (2016) Estimating the Cracking Tendency of Concrete
T 335-09 (2018) Determining the Percentage of Fracture in Coarse Aggregate
T 336-15 (2019) Coefficient of Thermal Expansion of Hydraulic Cement Concrete
T 337-09 (2014) Non-Instrumental Determination of Metallic Zinc in Zinc-Rich Primers
T 338-09 (2014) Analysis of Structural Steel Coatings for Hindered Amine Light Stabilizer
(HALS)
T 339-10 (2015) Analysis of Structural Steel Coatings for Isocyanate Content
T 340-10 (2015) Determining Rutting Susceptibility of Hot Mix Asphalt (HMA) Using the
Asphalt Pavement Analyzer (APA)
Number Title
T 341-10 (2014) Determination of Compression Capacity for Profile Wall Plastic Pipe by Stub
Compression Loading
T 342-11 (2015) Determining Dynamic Modulus of Hot Mix Asphalt (HMA)
T 343-12 (2016) Density of In-Place Hot Mix Asphalt (HMA) Pavement by Electronic Surface
Contact Devices
T 344-12 (2016) Evaluation of Superpave Gyratory Compactor (SGC) Internal Angle of
Gyration Using Simulated Loading
T 345-12 (2016) Passing Ability of Self-Consolidating Concrete (SCC) by J-Ring
T 346-13 (2017) Glass Beads Used in Pavement Markings
T 347-13 (2017) Slump Flow of Self-Consolidating Concrete (SCC)
T 348-13 (2018) Air-Void Characteristics of Freshly Mixed Concrete by Buoyancy Change
T 349-13 (2017) Filling Capacity of Self-Consolidating Concrete Using the Caisson Test
T 350-14 (2018) Multiple Stress Creep Recovery (MSCR) Test of Ashpalt Binder Using a
T 351-14 (2018) Visual Stability Index (VSI) of Self-Consolidating Concrete (SCC)
T 352-14 (2018) Determining Formwork Pressure of Fresh Self-Consolidating Concrete (SCC)
Using Pressure Transducers
T 353-14 (2018) Particle Size Analysis of Hydraulic Cement and Related Materials by Light
Scattering
T 354-17 Specific Gravity and Absorption of Aggregate by Volumetric Immersion
Method
T 355-18 In-Place Density of Asphalt Mixtures by Nuclear Methods
T 356-15 (2019) Determining Air Content of Hardened Portland Cement Concrete by High-
Pressure Air Meter
T 357-15 (2019) Predicting Chloride Penetration of Hydraulic Cement Concrete by the Rapid
Migration Procedure
T 358-19 Surface Resistivity Indication of Concrete's Ability to Resist Chloride Ion
Penetration
T 359M/T 359-18 Pavement Thickness by Magnetic Pulse Induction
T 360-16 Measurement of Tire/Pavement Noise Using the On-Board Sound Intensity
(OBSI) Method
T 361-16 Determining Asphalt Binder Bond Strength by Means of the Binder Bond
Strength (BBS) Test
T 362-17 Quantitative Determination of the Percentage of Lime in Asphalt Mixtures
T 363-17 Evaluating Stress Development and Cracking Potential due to Restrained
Volume Change Using a Dual Ring Test
T 364-17 Determination of Composite Activation Energy of Aggregates due to Alkali-
Silica Reaction (Chemical Method)
Number Title
T 365-17 Quantifying Calcium Oxychloride Amounts in Cement Pastes Exposed to
Deicing Salts
T 366-18 Apparent Viscosity of Hot-Poured Asphalt Crack Sealant Using Rotational
Viscometer
T 367-17 Accelerated Aging of Hot-Poured Asphalt Crack Sealant Using a Vacuum
Oven
T 368-17 Measuring Low-Temperature Flexural Creep Stiffness of Hot-Poured Asphalt
Crack Sealant by Bending Beam Rheometer (BBR)
T 369-17 Evaluation of the Low-Temperature Tensile Property of Hot-Poured Asphalt
Crack Sealant by Direct Tension Test
T 370-18 Measuring Adhesion of Hot-Poured Asphalt Crack Sealant Using Direct
Adhesion Tester
T 371-17 Measuring Interfacial Fracture Energy of Hot-Poured Asphalt Crack Sealant
Using a Blister Test
T 372M/T 372-17 Sensitivity of Stainless Steel to Intergranular Attack
T 373M/T 373-17 Comparative Qualitative Corrosion Characterization of Steel Bars Used for
Concrete Reinforcement (Linear Polarization Resistance and Potentiodynamic
Polarization Tests)
T 374M/T 374-17 Comparative Qualitative Corrosion Characterization of Uncoated Chromium-
Alloyed Steel Bars Used for Concrete Reinforcement (Tombstone Test)
T 375M/T 375-17 Identification of Iron-Based Alloy Steel Bars for Concrete Reinforcement or
Dowels by Handheld X-Ray Fluorescence (XRF) Spectrometer
T 376M/T 376-17 Microcell Slab Chloride Threshold
T 377-17 Detecting the Presence of Phosphorus in Asphalt Binder
T 378-17 Determining the Dynamic Modulus and Flow Number for Asphalt Mixtures
Using the Asphalt Mixture Performance Tester (AMPT)
T 379-18 Nonlinear Impact Resonance Acoustic Spectroscopy (NIRAS) for Concrete
Specimens with Damage from Alkali-Silica Reaction (ASR)
T 380-19 Potential Alkali Reactivity of Aggregates and Effectiveness of ASR
T 381-18 Determining Aggregate Shape Properties by Means of Digital Image Analysis
T 382-18 Determining the Viscosity of Emulsified Asphalt by a Rotational Paddle
Viscometer
T 383-18 Evaluation of Asphalt Release Agents (ARAs)
DELETED STANDARD
T 42-10 (2015) Preformed Expansion Joint Filler for Concrete Construction

or struck-through (for deletions) text. Unballoted editorial changes do not receive the change bar, highlighting, or strike-through; however, any standard that is
Technical
Subcommittee
T 24M/T 24-15 (2019) Obtaining and Testing Drilled Cores and Sawed Beams of Concrete 3c Reconfirmed for 2019 publication.
T 121M/T 121-19 Density (Unit Weight), Yield, and Air Content (Gravimetric) of 3b Revised internal vibrators in Section 4.3 to concur
Concrete with T 23.
T 133-19 Density of Hydraulic Cement 3a Revised to maintain equivalency with ASTM
C188.
T 148-15 (2019) Measuring Length of Drilled Concrete Cores 3c Reconfirmed for 2019 publication.
T 152-19 Air Content of Freshly Mixed Concrete by the Pressure Method 3b Revised internal vibrators in Section 4.15 to
concur with T 23.
T 158-11 (2019) Bleeding of Concrete 3b Reconfirmed for 2019 publication.
T 178-15 (2019) Portland-Cement Content of Hardened Hydraulic-Cement Concrete 3c Reconfirmed for 2019 publication.
T 192-19 Fineness of Hydraulic Cement by the 45-μm (No. 325) Sieve 3a Revised to maintain equivalency with ASTM
C430.
T 196M/T 196-11 (2019) Air Content of Freshly Mixed Concrete by the Volumetric Method 3b Reconfirmed for 2019 publication.
T 197M/T 197-11 (2019) Time of Setting of Concrete Mixtures by Penetration Resistance 3b Reconfirmed for 2019 publication.
T 198-15 (2019) Splitting Tensile Strength of Cylindrical Concrete Specimens 3c Reconfirmed for 2019 publication.
T 277-15 (2019) Electrical Indication of Concrete's Ability to Resist Chloride Ion 3c Reconfirmed for 2019 publication.
Penetration
T 282-01 (2019) Calibrating a Wheel Force or Torque Transducer Using a 5a Reconfirmed for 2019 publication.
Calibration Platform (User Level)
Technical
Subcommittee
T 309-15 (2019) Temperature of Freshly Mixed Portland Cement Concrete 3b Reconfirmed for 2019 publication.
T 318-15 (2019) Water Content of Freshly Mixed Concrete Using Microwave Oven 3b Reconfirmed for 2019 publication.
Drying
T 336-15 (2019) Coefficient of Thermal Expansion of Hydraulic Cement Concrete 3c Reconfirmed for 2019 publication.
T 356-15 (2019) Determining Air Content of Hardened Portland Cement Concrete by 3c Reconfirmed for 2019 publication.
High-Pressure Air Meter
T 357-15 (2019) Predicting Chloride Penetration of Hydraulic Cement Concrete by 3c Reconfirmed for 2019 publication.
the Rapid Migration Procedure
T 358-19 Surface Resistivity Indication of Concrete's Ability to Resist 3c Revised precision statements.
Chloride Ion Penetration
T 380-19 Potential Alkali Reactivity of Aggregates and Effectiveness of ASR 3c Revised a mold size in Section 4.1.1.
ii
PART 3—AASHTO PROVISIONAL STANDARDS
Number Title
AGGREGATES
TP 120-16 (2018) Pore Index for Carbonate Coarse Aggregate
MP 23-15 (2018) Reclaimed Asphalt Shingles for Use in Asphalt Mixtures
MP 25-17 Performance-Graded Hot-Poured Asphalt Crack Sealant
MP 26-15 (2018) Cotton Duck Fabric Bridge Bearings
MP 27-16 (2018) Materials for Emulsified Asphalt Chip Seals
MP 28-17 (2018) Materials for Micro Surfacing
MP 31-17 Materials for Cold Recycled Mixtures with Emulsified Asphalt
MP 32-17 (2019) Materials for Slurry Seal
MP 33-17 (2019) Materials for Emulsified Asphalt Fog Seal
MP 36-18 Materials for Asphalt Tack Coat
MP 37-18 Performance-Graded Asphalt Binder for Surface Treatments
MP 38-18 Mix Design of Cold Recycled Mixture with Foamed Asphalt
PP 76-13 (2015) Troubleshooting Asphalt Specimen Volumetric Differences between Superpave
Gyratory Compactors (SCGs) Used in the Design and the Field Management of
Superpave Mixtures
PP 77-14 (2018) Materials Selection and Mixture Design of Permeable Friction Courses (PFCs)
PP 78-17 Design Considerations When Using Reclaimed Asphalt Shingles (RAS) in Asphalt
Mixtures
PP 82-16 (2018) Emulsified Asphalt Chip Seal Design
PP 83-16 (2018) Micro Surfacing Design
PP 85-17 Grading or Verifying the Sealant Grade (SG) of a Hot-Poured Asphalt Crack Sealant
PP 86-17 Emulsified Asphalt Content of Cold Recycled Mixture Designs
PP 87-17 (2019) Slurry Seal Design
PP 88-17 (2019) Emulsified Asphalt Fog Seal Design
PP 93-18 Asphalt Tack Coat Design
PP 94-18 Determining Optimum Asphalt Content of Cold Recycled Mixture with Foamed
Asphalt
Number Title
PP 95-18 Preparation of Indirect Tension Performance Test Specimens
PP 96-18 Developing Dynamic Modulus Master Curves for Hot Mix Asphalt (HMA) Using the
Indirect Tension Testing Method
TP 92-14 (2018) Determining the Cracking Temperature of Asphalt Binder Using the Asphalt Binder
Cracking Device (ABCD)
TP 101-12 (2018) Estimating Fatigue Resistance of Asphalt Binders Using the Linear Amplitude Sweep
TP 105-13 (2015) Determining the Fracture Energy of Asphalt Mixtures Using the Semicircular Bend
Geometry (SCB)
TP 107-18 Determining the Damage Characteristic Curve of Asphalt Mixtures from Direct
Tension Cyclic Fatigue Tests
TP 108-14 (2018) Abrasion Loss of Asphalt Mixture Specimens
TP 113-15 Determination of Asphalt Binder Resistance to Ductile Failure Using Double-Edge-
Notched Tension (DENT) Test
TP 114-18 Determining the Interlayer Shear Strength (ISS) of Asphalt Pavement Layers
TP 115-16 (2017) Determining the Quality of Tack Coat Adhesion to the Surface of an Asphalt
Pavement in the Field or Laboratory
TP 116-15 Rutting Resistance of Asphalt Mixtures Using Incremental Repeated Load Permanent
Deformation (iRLPD)
TP 117-15 Determination of the Voids of Dry Compacted Filler
TP 122-16 (2018) Determination of Performance Grade of Physically Aged Asphalt Binder Using
Extended Bending Beam Rheometer (BBR) Method
TP 123-16 (2018) Measuring Asphalt Binder Yield Energy and Elastic Recovery Using the Dynamic
Shear Rheometer
TP 124-18 Determining the Fracture Potential of Asphalt Mixtures Using Semicircular Bend
Geometry (SCB) at Intermediate Temperature
TP 125-16 (2018) Determining the Flexural Creep Stiffness of Asphalt Mixtures Using the Bending
Beam Rheometer (BBR)
TP 126-17 Evaluation of the Tracking Resistance of Hot-Poured Asphalt Crack Sealant by
TP 127-17 Determining the Fracture Energy Density of Asphalt Binder Using the Binder
Fracture Energy (BFE) Test
TP 128-17 Evaluation of Oxidation Level of Asphalt Mixtures by a Portable Infrared
Spectrometer
TP 131-18 Determining Dynamic Modulus of Asphalt Concrete Using the Indirect Tension Test
BOX CULVERT, CULVERT PIPE, AND DRAIN TILE

MP 22-13 (2019) Fiber-Reinforced Polymer Composite Materials for Highway and Bridge Structures
Number Title
CONCRETE
PP 84-19 Performance Engineered Concrete Pavement Mixtures
PP 89-19 Grinding the Ends of Cylindrical Concrete Specimens
TP 118-17 (2018) Characterization of the Air-Void System of Freshly Mixed Concrete by the
Sequential Pressure Method
TP 119-15 (2019) Electrical Resistivity of a Concrete Cylinder Tested in a Uniaxial Resistance Test
TP 129-18 Vibrating Kelly Ball (VKelly) Penetration in Fresh Portland Cement Concrete
METALLIC MATERIALS AND COATINGS FOR BRIDGES

None
MISCELLANEOUS
PP 80-18 Continuous Thermal Profile of Asphalt Mixture Construction
PP 81-18 Intelligent Compaction Technology for Embankment and Asphalt Pavement
Applications
TP 96-13 (2018) Protective Sealers for Portland Cement Concrete
TP 103-13 (2018) Detectable Warning Systems

MP 24-15 (2018) Waterborne White and Yellow Traffic Paints
PP 74-13 (2018) Determination of Size and Roundness of Glass Beads Used in Traffic Markings by
Means of Computerized Optical Method
TP 106-13 (2015) Determination of Heavy Metal Content of Glass Beads Using X-Ray
Fluorescence (XRF)
TP 111-14 (2018) Measuring Retroreflectivity of Pavement Marking Materials Using a Mobile
Retroreflectivity Unit
TP 130-18 Producing Draw Down Panels and Measuring the Coefficient of Retroreflected
Luminance (RL) of Pavement Markings in a Laboratory Panel
PAVEMENT SURFACE AND STRUCTURE CHARACTERISTICS
MP 34-18 Materials for Sand Seals

MP 35-18 Thin Overlay Treatments Using a Binder Resin System and Aggregate for Concrete
Surfaces
PP 79-14 (2016) High-Friction Surface Treatment for Asphalt and Concrete Pavements
PP 90-18 Sand Seal Design
Number Title
PP 91-18 Emulsified Asphalt Scrub Seal Design
TP 98-18 Determining the Influence of Road Surfaces on Vehicle Noise Using the Statistical
Isolated Pass-By Method (SIP)
TP 99-18 Determining the Influence of Road Surfaces on Traffic Noise Using the Continuous-
Flow Traffic Time-Integrated Method (CTIM)
QUALITY ASSURANCE
MP 39-19 File Format of Intelligent Compaction Data
PP 73-13 (2018) Quality Assurance, Job Site Quality Control, and Reapplication of Protective Sealers
for Portland Cement Concrete
PP 97-19 Determination of Constant Mass
PP 98-19 Asphalt Surface Dielectric Profiling System Using Ground Penetrating Radar
SOILS
PP 92-18 Preparation of Test Specimens Using the Plastic Mold Compaction Device
TP 100-12 (2016) Deep Foundation Elements for Bi-Directional Static Axial Compressive Load
TP 104-13 (2015) Rapid Axial Compressive Load Testing of Deep Foundation Units
TP 112-14 (2018) Determining In-Place Density and Moisture Content of Soil and Soil–Aggregate
Using Complex Impedance Methodology
PART 3—AASHTO PROVISIONAL STANDARDS
Number Title
MP 22-13 (2019) Fiber-Reinforced Polymer Composite Materials for Highway and Bridge Structures
MP 23-15 (2018) Reclaimed Asphalt Shingles for Use in Asphalt Mixtures
MP 24-15 (2018) Waterborne White and Yellow Traffic Paints
MP 25-17 Performance-Graded Hot-Poured Asphalt Crack Sealant
MP 26-15 (2018) Cotton Duck Fabric Bridge Bearings
MP 27-16 (2018) Materials for Emulsified Asphalt Chip Seals
MP 28-17 (2018) Materials for Micro Surfacing
MP 31-17 Materials for Cold Recycled Mixtures with Emulsified Asphalt

MP 32-17 Materials for Slurry Seal
MP 33-17 Materials for Emulsified Asphalt Fog Seal
MP 34-18 Materials for Sand Seals
MP 35-18 Thin Overlay Treatments Using a Binder Resin System and Aggregate for Concrete
Surfaces
MP 36-18 Materials for Asphalt Tack Coat
MP 37-18 Performance-Graded Asphalt Binder for Surface Treatments
MP 38-18 Mix Design of Cold Recycled Mixture with Foamed Asphalt
MP 39-19 File Format of Intelligent Compaction Data
PP 73-13 (2018) Quality Assurance, Job Site Quality Control, and Reapplication of Protective Sealers
for Portland Cement Concrete
PP 74-13 (2018) Determination of Size and Roundness of Glass Beads Used in Traffic Markings by
Means of Computerized Optical Method
Number Title
PP 76-13 (2015) Troubleshooting Asphalt Specimen Volumetric Differences between Superpave
Gyratory Compactors (SCGs) Used in the Design and the Field Management of
Superpave Mixtures
PP 77-14 (2018) Materials Selection and Mixture Design of Permeable Friction Courses (PFCs)
PP 78-17 Design Considerations When Using Reclaimed Asphalt Shingles (RAS) in Asphalt
Mixtures
PP 79-14 (2016) High-Friction Surface Treatment for Asphalt and Concrete Pavements
PP 80-18 Continuous Thermal Profile of Asphalt Mixture Construction
PP 81-18 Intelligent Compaction Technology for Embankment and Asphalt Pavement
Applications
PP 82-16 (2018) Emulsified Asphalt Chip Seal Design
PP 83-16 (2018) Micro Surfacing Design
PP 84-19 Performance Engineered Concrete Pavement Mixtures
PP 85-17 Grading or Verifying the Sealant Grade (SG) of a Hot-Poured Asphalt Crack Sealant
PP 86-17 Emulsified Asphalt Content of Cold Recycled Mixture Designs
PP 87-17 Slurry Seal Design
PP 88-17 Emulsified Asphalt Fog Seal Design
PP 89-19 Grinding the Ends of Cylindrical Concrete Specimens
PP 90-18 Sand Seal Design
PP 91-18 Emulsified Asphalt Scrub Seal Design
PP 92-18 Preparation of Test Specimens Using the Plastic Mold Compaction Device
PP 93-18 Asphalt Tack Coat Design
PP 94-18 Determining Optimum Asphalt Content of Cold Recycled Mixture with Foamed
Asphalt
PP 95-18 Preparation of Indirect Tension Performance Test Specimens
PP 96-18 Developing Dynamic Modulus Master Curves for Hot Mix Asphalt (HMA) Using the
Indirect Tension Testing Method
PP 97-19 Determination of Constant Mass
PP 98-19 Asphalt Surface Dielectric Profiling System Using Ground Penetrating Radar
TP 92-14 (2018) Determining the Cracking Temperature of Asphalt Binder Using the Asphalt Binder
Cracking Device (ABCD)
Number Title
TP 96-13 (2018) Protective Sealers for Portland Cement Concrete
TP 98-18 Determining the Influence of Road Surfaces on Vehicle Noise Using the Statistical
Isolated Pass-By Method (SIP)
TP 99-18 Determining the Influence of Road Surfaces on Traffic Noise Using the Continuous-
Flow Traffic Time-Integrated Method (CTIM)
TP 100-12 (2018) Deep Foundation Elements for Bi-Directional Static Axial Compressive Load
TP 101-12 (2018) Estimating Fatigue Resistance of Asphalt Binders Using the Linear Amplitude Sweep
TP 103-13 (2018) Detectable Warning Systems

TP 104-13 (2015) Rapid Axial Compressive Load Testing of Deep Foundation Units
TP 105-13 (2015) Determining the Fracture Energy of Asphalt Mixtures Using the Semicircular Bend
Geometry (SCB)
TP 106-13 (2015) Determination of Heavy Metal Content of Glass Beads Using X-Ray
Fluorescence (XRF)
TP 107-18 Determining the Damage Characteristic Curve of Asphalt Mixtures from Direct
Tension Cyclic Fatigue Tests
TP 108-14 (2018) Abrasion Loss of Asphalt Mixture Specimens
TP 109-14 (2016) Nonlinear Impact Resonance Acoustic Spectroscopy (NIRAS) for Concrete
Specimens with Damage from the Alkali-Silica Reaction (ASR)
TP 111-14 (2018) Measuring Retroreflectivity of Pavement Marking Materials Using a Mobile

Retroreflectivity Unit
TP 112-14 (2018) Determining In-Place Density and Moisture Content of Soil and Soil–Aggregate
Using Complex Impedance Methodology
TP 113-15 Determination of Asphalt Binder Resistance to Ductile Failure Using Double-Edge-
Notched Tension (DENT) Test
TP 114-18 Determining the Interlayer Shear Strength (ISS) of Asphalt Pavement Layers
TP 115-16 (2017) Determining the Quality of Tack Coat Adhesion to the Surface of an Asphalt
Pavement in the Field or Laboratory
TP 116-15 Rutting Resistance of Asphalt Mixtures Using Incremental Repeated Load Permanent
Deformation (iRLPD)
TP 117-15 Determination of the Voids of Dry Compacted Filler
TP 118-17 (2018) Characterization of the Air-Void System of Freshly Mixed Concrete by the Sequential
Pressure Method
TP 119-15 (2019) Electrical Resistivity of a Concrete Cylinder Tested in a Uniaxial Resistance Test
TP 120-16 (2018) Pore Index for Carbonate Coarse Aggregate
Number Title
TP 122-16 (2018) Determination of Performance Grade of Physically Aged Asphalt Binder Using
Extended Bending Beam Rheometer (BBR) Method
TP 123-16 (2018) Measuring Asphalt Binder Yield Energy and Elastic Recovery Using the Dynamic
Shear Rheometer
TP 124-18 Determining the Fracture Potential of Ashalt Mixtures Using Semicircular Bend
Geometry (SCB) at Intermediate Temperature
TP 125-16 (2018) Determining the Flexural Creep Stiffness of Asphalt Mixtures Using the Bending
Beam Rheometer (BBR)
TP 126-17 Evaluation of the Tracking Resistance of Hot-Poured Asphalt Crack Sealant by

TP 127-17 Determining the Fracture Energy Density of Asphalt Binder Using the Binder Fracture
Energy (BFE) Test
TP 128-17 Evaluation of Oxidation Level of Asphalt Mixtures by a Portable Infrared
Spectrometer
TP 129-18 Vibrating Kelly Ball (VKelly) Penetration in Fresh Portland Cement Concrete
TP 130-18 Producing Draw Down Panels and Measuring the Coefficient of Retroreflected
Luminance (RL) of Pavement Markings in a Laboratory Panel
TP 131-18 Determining Dynamic Modulus of Asphalt Concrete Using the Indirect Tension Test
or struck-through text (for deletions). Unballoted editorial changes do not receive the change bar, highlighting, or strike-through; however, any standard that is
Technical
Subcommittee
MP 22-13 (2019) Fiber-Reinforced Polymer Composite Materials for Highway and 5b Reconfirmed for 2019 publication.
Bridge Structures
MP 32-17 (2019) Materials for Slurry Seal 5b Reconfirmed for 2019 publication.
MP 33-17 (2019) Materials for Emulsified Asphalt Fog Seal 5b Reconfirmed for 2019 publication.
MP 39-19 File Format of Intelligent Compaction Data 5c New Provisional standard.
PP 84-19 Developing Performance Engineered Concrete Pavement Mixtures 3c Removed restrained shrinkage language, edited
SAM criteria, and made other editorial
clarifications.
PP 87-17 (2019) Slurry Seal Design 5b Reconfirmed for 2019 publication.
PP 88-17 (2019) Emulsified Asphalt Fog Seal Design 5b Reconfirmed for 2019 publication.
PP 89-19 Grinding the Ends of Cylindrical Concrete Specimens 3c Revised Sections 1.2, 2.1, 3.4,4.1,5.1, 5.2,
5.3, 6.1, 6.5, and 6.6.
PP 97-19 Determination of Constant Mass 5c New Provisional standard.
PP 98-19 Asphalt Surface Dielectric Profiling System Using Ground 5c New Provisional standard.
Penetrating Radar
TP 119-15 (2019) Electrical Resistivity of a Concrete Cylinder Tested in a Uniaxial 3c Reconfirmed for 2019 publication.
Resistance Test
Provisional Standards—Current and Former
A searchable, comprehensive history of current and former provisional standards is provided, including:
• when first published;

• number of years into 8-year life cycle, if in use;
• final disposition, if no longer in use; and
• full standard number, if adopted.
ii
COMPREHENSIVE HISTORY OF CURRENT AND FORMER
AASHTO PROVISIONAL MATERIALS STANDARDS AND TEST METHODS
APRIL 2019
Provisional First
Standard Publ. Final Disposit.
Number Title Year Disposition Year Full Std. No.
MP 1 Performance Graded Asphalt Binder 1994 Adopted 2002 M 320
MP 1a Performance Graded Asphalt Binder 1996 Adopted 2005
MP 2 Superpave Volumetric Mix Design 1996 Adopted 2004 M 323
MP 5 Bridge Deck Cathodic Protection 1996 Deleted 1999 —
MP 6 Corrugated Polyethylene Pipe, 1050 and 1200 mm Diameter 1996 Adopted 1999 M 294
MP 7 Corrugated Polyethylene Pipe, 1350 and 1500 mm Diameter 1998 Adopted 2003
MP 8 Designing Stone Matrix Asphalt (SMA) 2000 Adopted 2008 M 325
MP 9 Compost for Erosion/Sediment Control (Filter Berms) 2003 Adopted 2010 R 51
MP 10 Compost for Erosion/Sediment Control (Compost Blankets) 2003 Adopted 2010 R 52
MP 11 Inertial Profiler 2003 Adopted 2010 M 328
MP 12 Detectable Warning Surfaces 2004 Adopted 2015 M 333
MP 13 Stainless Clad Deformed and Plain Round Steel Bars for 2004 Adopted 2011 M 329
Concrete Reinforcement
MP 14 Smoothness of Pavement at the Approaches to Weight-in- 2005 Adopted 2013 M 331

Motion (WIM) Scales
MP 15 Use of Reclaimed Asphalt Shingles as an Additive in Hot- 2006 Deleted 2014 —

Mix Asphalt
MP 16 Reclaimed Concrete Aggregate for Use as Coarse Aggregate 2007 Deleted 2016 —
in Hydraulic Cement (August)
MP 17 Pavement Ride Quality When Measured Using Inertial 2004 Adopted 2010 R 54
Profiling Systems
MP 18 Uncoated, Corrosion-Resistant, Deformed and Plain 2009 Adopted 2017 M 334M/M 334
Chromium Alloyed, Billet-Steel Bars for Concrete (June) and T 372M/T 372
Reinforcement and Dowels through
T 376M/T 376
MP 19 Performance-Graded Asphalt Binder Using Multiple Stress 2010 Adopted 2014 M 332
Provisional First
MP 20 Steel-Reinforced Polyethylene (PE) Ribbed Pipe, 300- to 2010 Adopted 2018 M 335
1500-mm (12- to 60-in.) Diameter (June)
MP 21 Polypropylene Pipe, 300- to 500-mm (12- to 60-in.) 2011 Adopted 2013 M 330
MP 22 Fiber-Reinforced Polymer Composite Materials for Highway 2013

and Bridge Structures
MP 23 Reclaimed Asphalt Shingles for Use in Asphalt Mixtures 2014
MP 24 Waterborne White and Yellow Traffic Paints 2014
MP 25 Performance-Graded Hot-Poured Asphalt Crack Sealant 2015
MP 26 Cotton Duck Fabric Bridge Bearings 2015
MP 27 Materials for Emulsified Asphalt Chip Seals 2016
MP 28 Materials for Micro Surfacing 2016
MP 29 This standard number was inadvertently skipped.
MP 30 Steel Wire and Welded Wire, Plain and Deformed, for 2017 Adopted 2018 M 336M/M 336
Concrete Reinforcement (June)
MP 31 Materials for Cold Recycled Mixtures with Emulsified 2017

Asphalt
MP 32 Materials for Slurry Seal 2017
MP 33 Materials for Emulsified Asphalt Fog Seal 2017
MP 34 Materials for Sand Seals 2018
MP 35 Thin Overlay Treatments Using a Binder Resin System and 2018

Aggregate for Concrete Surfaces
MP 36 Materials for Asphalt Tack Coat 2018
MP 37 Performance-Graded Asphalt Binder for Surface Treatments 2018
MP 38 Mix Design of Cold Recycled Mixture with Foamed Asphalt 2018
MP 39 File Format of Intelligent Construction Data 2019
PP 1 Accelerated Aging of Asphalt Binder Using a Pressurized 1994 Adopted 2002 R 28

Aging Vessel (PAV)
PP 2 Mixture Conditioning of Hot-Mix Asphalt (HMA) 1995 Adopted 2002 R 30
PP 3 Preparing Hot Mix Asphalt (HMA) Specimens by Means of 1995 Deleted 2003 —
the Rolling Wheel Compactor
Provisional First
PP 5 Laboratory Evaluation of Modified Asphalt Systems 1994 Deleted 1998 —
PP 6 Grading or Verifying the Performance Grade of an Asphalt 1994 Adopted 2002 R 29

Binder
PP 7 Calibrating the Load Cell and Deflection Sensors for a 1995 Adopted 2003 R 32
PP 8 Calibrating the Reference Load Cell Used for reference 1995 Adopted 2003 R 33
Calibrations for Falling Weight Deflectometer
PP 10 Operational Guidelines on Test Pits for Evaluating Pavement 1994 Deleted 1995 —a
Performance
PP 19 Volumetric Analysis of Compacted Hot Mix Asphalt (HMA) 1994 Deleted 2002 —
PP 20 Evaluating the Performance of Crack Sealing Treatments on 1995 Deleted 2004 —

Asphalt Surfaced Pavement
PP 21 Testing and Evaluating Cold Mix Patching Materials 1995 Deleted 2002 —
PP 22 Selecting and Specifying Crack Sealants for Asphalt Surfaced 1996 Deleted 2002 —
Pavement
PP 23 Evaluating the Condition of Portland Cement Concrete 1996 Deleted 2003 —

Bridge Components
PP 25 Evaluating the Performance of Joint Seals in Portland 1996 Deleted 2002 —

Cement Concrete Pavement
PP 26 Certifying Suppliers of Performance Graded Asphalt Binders 1997 Adopted 2001 R 26
PP 28 Superpave Volumetric Design for Hot-Mix Asphalt (HMA) 1996 Adopted 2004 R 35
PP 29 Evaluating Deicing Chemicals 1996 Adopted 2003 R 34
PP 30 Evaluation of Coating Systems with Zinc Rich Primers 1996 Adopted 2002 R 31
PP 31 Measuring Pavement Profile Using a Rod and Level 1997 Adopted 2005 R 40
PP 32 Measuring Pavement Profile Using a Dipstick® 1997 Adopted 2005 R 41
PP 33 Decommissioning Geotechnical Exploratory Boreholes 1997 Adopted 1998 R 22
PP 34 Estimating the Cracking Tendency of Concrete 1998 Adopted 2008 T 334
PP 35 Evaluation of Superpave™ Gyratory Compactors (SGCs) 1998 Deleted 2007 —
PP 36 Assessment of Corrosion of Steel Piling for Non-Marine 1998 Adopted 2002 R 27

Applications
Provisional First
PP 37 Determination of International Roughness Index (IRI) to 1999 Combined 2007 R 43M/

Quantify Roughness of Pavements and Adopted R 43
PP 37M Quantifying Roughness of Pavements 1999
PP 38 Determining Maximum Rut Depth in Asphalt Pavements 1999 Adopted 2008 R 48
PP 39 Estimating Faulting of Concrete Pavements 1999 Adopted 2004 R 36
PP 40 Application of Ground Penetrating Radar (GPR) to Highways 2000 Adopted 2004 R 37
PP 41 Designing Stone Matrix Asphalt (SMA) 2000 Adopted 2008 R 46
PP 42 Determination of Low-Temperature Performance Grade (PG) 2001 Adopted 2009 R 49

of Asphalt Binders
PP 44 Quantifying Cracks in Asphalt Pavement Surface 2001 Adopted 2010 R 55
PP 45 Qualification of Deformed and Plain Steel Bar Producing 2001 Adopted 2010 R 53
Mills
PP 46 Geosynthetic Reinforcement of the Aggregate Base Course of 2001 Adopted 2009 R 50

Flexible Pavement Structures
PP 47 Evaluation of Different Superpave™ Gyratory Compactors 2002 Deleted 2009 —

(SGCs) Used in the Design and the Field Management of
Superpave™ Mixtures
PP 48 Evaluation of the Superpave™ Gyratory Compactor (SGC) 2003 Deleted 2010 —

Internal Angle of Gyration
PP 49 Certification of Inertial Profiling Systems 2003 Adopted 2010 R 56
PP 50 Operating Inertial Profilers and Evaluating Pavement Profiles 2003 Adopted 2010 R 57
PP 51 Pavement Ride Quality When Measured Using Inertial 2003 Adopted 2010 R 54b
Profiling Systems
PP 52 Developing a Quality Assurance Plan for Hot-Mix Asphalt 2005 Adopted 2006 R 42
(HMA)
PP 53 Design Considerations When Using Reclaimed Asphalt 2006 Deleted 2014 —

Shingles (RAS) in New Hot Mix Asphalt (HMA)
PP 54 Match Curing of Concrete Test Specimens 2006 Adopted 2016 R 72

(April)
PP 55 Overcoating Field Test Program for Evaluating Protective 2006 Deleted 2012 —
Coatings on Existing Bridges or Salvaged Beams
PP 56 Evaluating the Engineering and Environmental Suitability of 2006 Adopted 2014 R 65

Recycled Materials
Provisional First
PP 57 Establishing Requirements for and Performing Equipment 2006 Adopted 2012 R 61

Calibrations, Standardizations, and Checks
PP 58 Static Segregation of Hardened Self-Consolidating Concrete 2008 Adopted 2017 R 81c

(SCC) Cylinders (April)
PP 59 Coal Combustion Fly Ash for Embankments 2009 Deleted 2016 —

(August)
PP 60 Preparation of Cylindrical Performance Test Specimens 2009 Adopted 2017 R 83

Using the Superpave Gyratory Compactor (SGC) (August)
PP 61 Developing Dynamic Modulus Master Curves for Asphalt 2009 Adopted 2017 R 84
Mixtures Using the Asphalt Mixture Performance Tester (August)
(AMPT)
PP 62 Developing Dynamic Modulus Master Curves for Hot Mix 2009 Adopted 2013 R 62
Asphalt (HMA)
PP 63 Pipe Joint Selection for Highway Culvert and Storm Drains 2009 Adopted 2017 R 82
(June)
PP 64 Determining Aggregate Source Shape Values from Digital 2010 Adopted 2018 R 91
Image Analysis Shape Properties (August)
PP 65 Determining the Reactivity of Concrete Aggregates and 2010

Selecting Appropriate Measures for Preventing Deleterious
Expansion in New Concrete Construction
PP 66 Determination of Long-Term Strength for Geosynthetic 2010 Adopted 2015 R 69

Reinforcement
PP 67 Quantifying Cracks in Asphalt Pavement Surfaces from 2010 Adopted 2018 R 85

Collected Images Utilizing Automated Methods (April)
PP 68 Collecting Images of Pavement Surfaces for Distress 2010 Adopted 2018 R 86

Detection (April)
PP 69 Determining Pavement Deformation Parameters and Cross 2010 Adopted 2018 R 87

Slope from Collected Transverse Profiles (April)
PP 70 Collecting the Transverse Pavement Profile 2010 Adopted 2018 R 88

(April)
PP 71 Certifying Suppliers of Emulsified Asphalt 2011 Adopted 2016 R 77

(August)
PP 72 Recovering Residue from Emulsified Asphalt Using Low- 2011 Adopted 2016 R 78
Temperature Evaporative Techniques (August)
PP 73 Quality Assurance, Job Site Quality Control, and 2011

Reapplication of Protective Sealers for Portland Cement
Concrete
Provisional First
PP 74 Determination of Size and Roundness of Glass Beads Used in 2011

Traffic Markings by Means of Computerized Optical Method
PP 75 Vacuum Drying Compacted Asphalt Specimens 2013 Adopted 2016 R 79

(August)
PP 76 Troubleshooting Asphalt Specimen Volumetric Differences 2013

between Superpave Gyratory Compactors (SGCs) Used in the
Design and the Field Management of Superpave Mixtures
PP 77 Materials Selection and Mixture Design of Permeable 2014

Friction Courses (PFCs)
PP 78 Design Considerations When Using Reclaimed Asphalt 2014

Shingles (RAS) in Asphalt Mixtures
PP 79 High Friction Surface Treatment for Asphalt and Concrete 2014

Pavements
PP 80 Continuous Thermal Profile of Asphalt Mixture Construction 2014
PP 81 Intelligent Compaction Technology for Embankment and 2014

Asphalt Pavement Applications
PP 82 Emulsified Asphalt Chip Seal Design 2016
PP 83 Micro Surfacing Design 2016
PP 84 Performance Engineered Concrete Pavement Mixtures 2017
PP 85 Grading or Verifying the Sealant Grade (SG) of a Hot-Poured 2017

Asphalt Crack Sealant
PP 86 Emulsified Asphalt Content of Cold Recycled Mixture 2017

Designs
PP 87 Slurry Seal Design 2017
PP 88 Emulsified Asphalt Fog Seal Design 2017
PP 89 Grinding the Ends of Cylindrical Concrete Specimens 2018
PP 90 Sand Seal Design 2018
PP 91 Emulsified Asphalt Scrub Seal Design 2018
PP 92 Preparation of Test Specimens Using the Plastic Mold 2018

Compaction Device
PP 93 Asphalt Tack Coat Design 2018

Provisional First
PP 94 Determining Optimum Asphalt Content of Cold Recycled 2018

Mixture with Foamed Asphalt
PP 95 Preparation of Indirect Tension Performance Test Specimens 2018
PP 96 Developing Dynamic Modulus Master Curves for Hot Mix 2018

Asphalt (HMA) Using the Indirect Tension Testing Method
PP 97 Determination of Constant Mass 2019
PP 98 Asphalt Surface Dielectric Profiling System Using Ground 2019

Penetrating Radar
TP 1 Determining the Flexural Creep Stiffness of Asphalt Binder 1994 Adopted 2002 T 313
Using the Bending Beam Rheometer (BBR)
TP 2 Quantitative Extraction and Recovery of Asphalt Binder from 1995 Adopted 2003 T 319
Hot Mix Asphalt HMA
TP 3 Determining the Fracture Properties of Asphalt Binder in 1994 Adopted 2002 T 314
Direct Tension (DT)
TP 4 Preparing and Determining the Density of Hot-Mix Asphalt 1994 Adopted 2001 T 312
(HMA) Specimens by Means of the Superpave Gyratory
Compactor
TP 5 Determining the Rheological Properties of Asphalt Binder 1995 Adopted 2002 T 315
Using a Dynamic Shear Rheometer (DSR)
TP 6 Measurement of Initial Asphalt Adsorption and Desorption in 1994 Deleted 1999 —

the Presence of Moisture
TP 7 Determining the Permanent Deformation and Fatigue 1995 Adopted 2003 T 320
Cracking Characteristics of Hot Mix Asphalt (HMA) Using
the Simple Shear Test (SST) Device
TP 8 Determining the Fatigue Life of Compacted Hot Mix Asphalt 1995 Adopted 2003 T 321
(HMA) Subjected to Repeated Flexural Bending
TP 9 Determining the Creep Compliance and Strength of Hot Mix 1995 Adopted 2003 T 322
Asphalt (HMA) Using the Indirect Tensile Test Device
TP 10 Thermal Stress Restrained Specimen Tensile Strength 1994 Deleted 2002 —
TP 11 Rapid Determination of Corrosion Rate of Uncoated Steel in 1996 Deleted 2004 —

Reinforced Concrete
TP 12 Determining the Hydraulic Fracture of Coarse Aggregate 1994 Deleted 2001 —
TP 14 Accelerated Detection of Potentially Deleterious Expansion 1994 Adopted 1996 T 303

of Mortar Bars Due to Alkali-Silica Reaction
TP 17 Resistance of Concrete to Rapid Freezing and Thawing 1994 Deleted 2002 —

Provisional First
TP 18 Method for Determining the Fundamental Transverse 1995 Deleted 2003 —

Frequency and Quality Factor of Concrete Prism Specimens
TP 19 Flexural Strength of Concrete (Using Simple Beam with 1994 Deleted 2002 —
Third-Point Loading)
TP 20 Compressive Strength of Cylindrical Concrete Specimens 1994 Adopted 1997 T 22
TP 22 Rapid Determination of the Chloride Penetrability of 1995 Deleted 2003 —

Concrete Using AC Impedance
TP 23 Water Content of Freshly Mixed Concrete Using Microwave 1994 Adopted 2002 T 318
Oven Drying
TP 24 Determining the Density of Freshly Mixed Concrete in Place 1995 Deleted 2003 —
Using a Twin-Probe Nuclear Density Gauge
TP 26 Determining the Relative Permeability of Concrete by 1995 Deleted 2003 —

Surface Air Flow
TP 28 Detection of Voids Under Rigid Pavement 1995 Deleted 2003 —
TP 29 Determining the Shear Strength at the Interface of Bonded 1995 Adopted 2003 T 323
Layers of Portland Cement Concrete
TP 31 Determining the Resilient Modulus of Bituminous Mixtures 1995 Deleted 2003 —

by Indirect Tension
TP 33 Uncompacted Void Content of Fine Aggregate (As 1994 Adopted 1996 T 304
Influenced by Particle Shape, Surface Texture, and Grading)
TP 34 Determining Moisture Sensitivity Characteristics of 1994 Deleted 1999 —

Compacted Bituminous Mixtures Subjected to Hot and Cold
Climate Conditions
TP 35 Determining the Relative Effectiveness of Penetrating 1994 Deleted 2002 —

Concrete Sealers by Electrical Resistance
TP 36 Evaluating Asphalt-Covered Concrete Bridge Decks Using 1994 Deleted 2002 —

Pulsed Radar
TP 37 Determining the Condition Rating of Preformed Membranes 1994 Deleted 2002 —

on Concrete Bridge Decks Using Pulse Velocity
TP 39 Determining the Maximum Specific Gravity of Bituminous 1995 Adopted 1999 T 209
Paving Mixtures
TP 40 Determining the Percent Asphalt Required for Coating 1995 Deleted 2002 —
Aggregates Used in Cold Mix Patching Materials
TP 41 Determining the Percent Asphalt Required Based on 1995 Deleted 2002 —

Stripping of Aggregates Used in Cold Mix Patching
Materials
Provisional First
TP 42 Percent Asphalt Based on Drainability of Aggregates Used in 1995 Deleted 2002 —

Cold Mix Patching Materials
TP 43 Workability of Cold Mix Patching Materials 1995 Deleted 2002 —
TP 44 Cohesion of Cold Mix Patching Materials 1995 Deleted 2002 —
TP 46 Determining the Resilient Modulus of Soils and Aggregate 1995 Adopted 1999 T 307
Materials
TP 47 Determining the Ecological Effects of Deicing Chemicals 1995 Deleted 2002 —
TP 48 Viscosity Determination of Asphalt Binder Using Rotational 1995 Adopted 2002 T 316
Viscometer
TP 50 Determining the Relative Effectiveness of Penetrating 1996 Deleted 2004 —

Concrete Sealers by Water Absorption
TP 51 Testing Cathodic Protection Materials and Systems for 1996 Deleted 2004 —
Bridge Decks
TP 52 Estimating the Strength of Concrete in Transportation 1996 Adopted 2004 T 325

Construction by Maturity Tests
TP 53 Determining the Asphalt Content of Hot Mix Asphalt (HMA) 1996 Adopted 1999 T 308
by the Ignition Method
TP 54 Determining Early Stiffening Characteristics of Portland 1997 Deleted 2004 —

Cement Paste (Mini Slump Cone Method)
TP 55 Determining Chloride Ions in Concrete and Concrete 1998 Adopted 2007 T 332
Materials by Specific Ion Probe
TP 56 Uncompacted Void Content of Coarse Aggregate (As 1998 Adopted 2005 T 326
Influenced by Particle Shape, Surface Texture, and Grading)
TP 57 Methylene Blue Value of Clays, Mineral Fillers, and Fines 1998 Adopted 2007 T 330
TP 58 Resistance of Coarse Aggregate to Degradation by Abrasion 1999 Adopted 2005 T 327

in the Micro-Deval Apparatus
TP 59 Determining Air Content of Hardened Portland Cement 1999 Adopted 2015 T 356
Concrete by High-Pressure Air Meter
TP 60 Coefficient of Thermal Expansion of Hydraulic Cement 2000 Adopted 2009 T 336

Concrete
TP 61 Determining the Percentage of Fracture in Coarse Aggregate 2002 Adopted 2009 T 335
TP 62 Determining Dynamic Modulus of Hot-Mix Asphalt 2003 Adopted 2011 T 342

Concrete Mixtures
Provisional First
TP 63 Determining Rutting Susceptibility of Asphalt Paving 2003 Adopted 2010 T 340

Mixtures Using the Asphalt Pavement Analyzer (APA)
TP 64 Predicting Chloride Penetration of Hydraulic Cement 2003 Adopted 2015 T 357

Concrete by the Rapid Migration Procedure
TP 65 Non-Instrumental Determination of Metallic Zinc in Zinc- 2003 Adopted 2009 T 337

Rich Primers
TP 66 Analysis of Structural Steel Coatings for Hindered Amine 2003 Adopted 2009 T 338
Light Stabilizer (HALS)
TP 67 Analysis of Structural Steel Coatings for Isocyanate Content 2003 Adopted 2009 T 339
TP 68 Density of In-Place Hot-Mix Asphalt (HMA) Pavement by 2004 Adopted 2012 T 343
Electronic Surface Contact Devices
TP 69 Bulk Specific Gravity and Density of Compacted Asphalt 2004 Adopted 2007 T 331
Mixtures Using Automatic Vacuum Sealing Method
TP 70 Multiple Stress Creep Recovery (MSCR) Test of Asphalt 2007 Adopted 2014 T 350
Binder Using a Dynamic Shear Rheometer (DSR)
TP 71 Evaluation of Superpave Gyratory Compactor (SGC) Internal 2007 Adopted 2012 T 344
Angle of Gyration Using Simulated Loading
TP 72 Quantitative Determination of the Percentage of Lime in Hot 2008 Adopted 2016 T 362
Mix Asphalt (HMA) (August)
TP 73 Slump Flow of Self-Consolidating Concrete (SCC) 2008 Adopted 2013 T 347
TP 74 Passing Ability of Self-Consolidating Concrete (SCC) by 2008 Adopted 2012 T 345

J-Ring
TP 75 Air-Void Characteristics of Freshly Mixed Concrete by 2008 Adopted 2013 T 348

Buoyancy Change
TP 76 Measurement of Tire/Pavement Noise Using the On-Board 2008 Adopted 2016 T 360
Sound Intensity (OBSI) Method (April)
TP 77 Specific Gravity and Absorption of Aggregate by Volumetric 2009 Adopted 2015 T 354
Immersion Method
TP 78 Detecting the Presence of Phosphorous in Asphalt Binder 2009 Adopted 2017 T 377c
(August)
TP 79 Determining the Dynamic Modulus and Flow Number for 2009 Adopted 2017 T 378
Asphalt Mixtures Using the Asphalt Mixture Performance (August)
Tester (AMPT)
TP 80 Visual Stability Index (VSI) of Self-Consolidating Concrete 2009 Adopted 2014 T 351
(SCC)
Provisional First
TP 81 Determining Aggregate Shape Properties by Means of Digital 2010 Adopted 2018 T 381
Image Analysis (August)
TP 82 Bulk Specific Gravity (Gmb) of Compacted Bituminous 2010 Deleted 2018 —

Mixtures Using Water Displacement Measured by Pressure (August)
Sensor
TP 83 Sampling and Fabrication of 50-mm (2-in.) Cube Specimens 2010 Adopted 2014 R 64
Using Grout (Non-Shrink) or Mortar
TP 84 Evaluation of Adhesive Anchors in Concrete Under 2010 Deleted 2018 —

Sustained Loading Conditions (June)
TP 85 Apparent Viscosity of Hot-Poured Bituminous Crack Sealant 2010 Adopted 2017 T 366
Using Brookfield Rotational Viscometer RV Series (June)
Instrument
TP 86 Accelerated Aging of Bituminous Sealants and Fillers with a 2010 Adopted 2017 T 367
Vacuum Oven (June)
TP 87 Measure Low Temperature Flexural Creep Stiffness of 2010 Adopted 2017 T 368
Bituminous Sealants and Fillers by Bending Beam (June)
Rheometer (BBR)
TP 88 Evaluation of the Low-Temperature Tensile Property of 2010 Adopted 2017 T 369

Bituminous Sealants by Direct Tension Test (June)
TP 89 Measuring Adhesion of Hot-Poured Crack Sealant Using 2010 Adopted 2017 T 370
Direct Adhesion Tester (June)
TP 90 Measuring Interfacial Fracture Energy of Hot-Poured Crack 2010 Adopted 2017 T 371
Sealant Using a Blister Test (June)
TP 91 Determining Asphalt Binder Bond Strength by Means of the 2011 Adopted 2016 T 361
Asphalt Bond Strength (ABS) Test (August)
TP 92 Determining the Cracking Temperature of Asphalt Binder 2011

Using the Asphalt Binder Cracking Device (ABCD)
TP 93 Determining Formwork Pressure of Fresh Self-Consolidating 2011 Adopted 2014 T 352

Concrete Using Pressure Transducers
TP 94 Filling Capacity of Self-Consolidating Concrete Using the 2011 Adopted 2013 T 349
Caisson Test
TP 95 Surface Resistivity Indication of Concrete’s Ability to Resist 2011 Adopted 2015 T 358
Chloride Ion Penetration
TP 96 Protective Sealers for Portland Cement Concrete 2011
TP 97 Glass Beads Used in Pavement Markings 2011 Adopted 2012 T 346

Provisional First
TP 98 Determining the Influence of Road Surfaces on Vehicle 2011

Noise Using the Statistical Isolated Pass-By (SIP) Method
TP 99 Determining the Influence of Road Surfaces on Traffic Noise 2011

Using the Continuous-Flow Traffic Time-Integrated Method
(CTIM)
TP 100 Deep Foundation Elements under Bidirectional Static Axial 2012

Compressive Load
TP 101 Estimating Fatigue Resistance of Asphalt Binders Using the 2012

Linear Amplitude Sweep
TP 102 Evaluation of Asphalt Release Agents 2012 Adopted 2018 T 383

(August)
TP 103 Detectable Warning Systems 2012
TP 104 Rapid Axial Compressive Load Testing of Deep Foundation 2013

Units
TP 105 Determining the Fracture Energy of Asphalt Mixtures Using 2013

the Semicircular Bend Geometry (SCB)
TP 106 Determination of Heavy Metal Content of Glass Beads Using 2013

X-Ray Fluorescence (XRF)
TP 107 Determining the Damage Characteristic Curve of Asphalt 2014

Mixtures from Direct Tension Cyclic Fatigue Tests
TP 108 Determining the Abrasion Loss of Asphalt Mixture 2014

Specimens
TP 109 Nonlinear Impact Resonance Acoustic Spectroscopy 2014 Adopted 2018 T 379
(NIRAS) for Concrete Specimens with Damage from the (April)
Alkali-Silica Reaction (ASR)
TP 110 Potential Alkali Reactivity of Aggregates and Effectiveness 2014 Adopted 2018 T 380
of ASR Mitigation Measures (Miniature Concrete Prism Test, (April)
MCPT)
TP 111 Measuring Retroreflectivity of Pavement Marking Materials 2014

Using a Mobile Retroreflectivity Unit
TP 112 Determining In-Place Density and Moisture Content of Soil 2014

and Soil-Aggregate Using Complex Impedance Methodology
TP 113 Determination of Asphalt Binder Resistance to Ductile 2015

Failure Using Double-Edge-Notched Tension (DENT) Test
TP 114 Determining the Interlayer Shear Strength (ISS) of Asphalt 2015

Pavement Layers
Provisional First
TP 115 Determining the Quality of Tack Coat Adhesion to the 2015

Surface of an Asphalt Pavement in the Field or Laboratory
TP 116 Rutting Resistance of Asphalt Mixtures Using Incremental 2015

Repeated Load Permanent Deformation (iRLPD)
TP 117 Determination of the Voids of Dry Compacted Filler 2015
TP 118 Characterization of the Air-Void System of Freshly Mixed 2015

Concrete by the Sequential Pressure Method
TP 119 Electrical Resistivity of a Concrete Cylinder Tested in a 2015

Uniaxial Resistance Test
TP 120 Pore Index for Carbonate Coarse Aggregate 2016
TP 121 Determining the Viscosity of Emulsified Asphalt by a 2016 Adopted 2018 T 382
Rotational Paddle Viscometer (August)
TP 122 Determination of Performance Grade of Physically Aged 2016

Asphalt Binder Using Extended Bending Beam Rheometer
(BBR) Method
TP 123 Measuring Asphalt Binder Yield Energy and Elastic 2016

Recovery Using the Dynamic Shear Rheometer
TP 124 Determining the Fracture Potential of Ashalt Mixtures Using 2016

Semicircular Bend Geometry (SCB) at Intermediate
Temperature
TP 125 Determining the Flexural Creep Stiffness of Asphalt 2016

Mixtures Using the Bending Beam Rheometer (BBR)
TP 126 Evaluation of the Tracking Resistance of Hot-Poured Asphalt 2017

Crack Sealant by Dynamic Shear Rheometer (DSR)
TP 127 Determining the Fracture Energy Density of Asphalt Binder 2017

Using the Binder Fracture Energy (BFE) Test
TP 128 Evaluation of Oxidation Level of Asphalt Mixtures by a 2017

Portable Infrared Spectrometer
TP 129 Vibrating Kelly Ball (VKelly) Penetration in Fresh Portland 2018

Cement Concrete
TP 130 Producing Draw Down Panels and Measuring the 2018

Coefficient of Retroreflected Luminance (RL) of
Pavement Markings in a Laboratory Panel
TP 131 Determining Dynamic Modulus of Asphalt Concrete 2018

Using the Indirect Tension Test
a
Adopted in 1995 as R 19. R 19 was discontinued in 2004.
b
Reclassified as a provisional specification MP 17 in 2007 then reclassified again as a practice when adopted as a full
standard.
c
Discontinued in 2016 then adopted in 2017.
ABOUT AASHTO DESIGNATION NUMBERS
Anatomy of a Designation Number
Components
T xxx - 16
Standard Type Standard Number Two-Digit Revision Year
M xxx-12 (2016) Four-Digit Reconfirmation Year
Standard Types
Standard types are represented by a one-letter abbreviation for full standards. The letter “P” is added for provisional
standards. The standard type abbreviations are as follows:
• M (Materials, full) • MP (Materials, provisional)

• T (Test, full) • TP (Test, provisional)
• R (PRactice, full) • PP (Practice, provisional)
Standard Numbers
Standard numbers are sequential within standard type. Thus, a provisional that is subsequently adopted as a full
standard will receive a new number.
Revised vs. Reconfirmed and Discontinued vs. Deleted
A full or provisional standard is designated as revised if technical changes have been balloted and approved by
AASHTO’s Committee on Materials and Pavements. A standard is designated as reconfirmed if it has undergone
technical review to determine that it is up to date and in use and that it does not require revision; such a review is
required:
• every four years for a full standard, and

• every one or two years for a provisional standard, depending on its progress through its 8-year provisional
life cycle.
If a standard is no longer used, it may be discontinued by Committee vote, in which case the standard header
will be published that year with a notice saying that the standard has been discontinued and giving a brief
explanation as to why. In subsequent years, the standard will be deleted from the book, meaning that it is no longer
maintained.

HM 2019TableofContents PDF

Uploaded by

Copyright:

Available Formats

HM 2019TableofContents PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HM 2019TableofContents PDF

Uploaded by

Copyright:

Available Formats

PART 1—STANDARD SPECIFICATIONS AND STANDARD PRACTICES

SUBJECT SEQUENCE TABLE OF CONTENTS

M 81-92 (2017) Cutback Asphalt (Rapid-Curing Type)

© 2018 by the American Association of State Highway and Transportation Officials.

BOX CULVERT, CULVERT PIPE, AND DRAIN TILE

M 36-16 Corrugated Steel Pipe, Metallic-Coated, for Sewers and Drains

CONCRETE, CURING MATERIALS, AND ADMIXTURES

M 154M/M 154-12 (2016) Air-Entraining Admixtures for Concrete

R 23-99 (2018) Chemical, Biological, and Physical Analysis of Water

GUARDRAIL AND FENCING

M 180-12 (2017) Corrugated Sheet Steel Beams for Highway Guardrail

M 85-19 Portland Cement

JOINT FILLER AND ASPHALT PLANK

METALLIC MATERIALS FOR BRIDGES

M 334M/M 334-17 Uncoated, Corrosion-Resistant, Deformed and Plain Chromium Alloyed,

M 143-14 (2018) Sodium Chloride

R 25-19 Technician Training and Certification Programs

PAINTING AND TRAFFIC MARKING AND SIGNING

PAVEMENT SURFACE AND STRUCTURE CHARACTERISTICS

R 56-14 (2018) Certification of Inertial Profiling Systems

R 9-05 (2018) Acceptance Sampling Plans for Highway Construction

REINFORCING STEEL AND WIRE ROPE

M 254-06 (2015) Corrosion-Resistant Coated Dowel Bars

SOILS AND STABILIZATION

M 57-80 (2017) Materials for Embankments and Subgrades

TIMBER AND PRESERVATIVES

M 133-12 (2016) Preservatives and Pressure Treatment Processes for Timber

M 32M/M 32-09 (2013) Steel Wire, Plain, for Concrete Reinforcement

M 57-80 (2017) Materials for Embankments and Subgrades

M 224-91 (2019) Use of Protective Sealers for Portland Cement Concrete

M 226-80 (2017) Viscosity-Graded Asphalt Cement

R 18-18 Establishing and Implementing a Quality Management System for

R 49-09 (2018) Determination of Low-Temperature Performance Grade (PG) of Asphalt

R 56-14 (2018) Certification of Inertial Profiling Systems

M 32M/M 32-09 (2013) Steel Wire, Plain, for Concrete Reinforcement

Release: Group 1 (April 2019)

BOX CULVERT, CULVERT PIPE, AND DRAIN PIPE

CONCRETE, CURING MATERIALS, AND ADMIXTURES

JOINT FILLER, SEALANTS, AND ASPHALT PLANK

METALLIC MATERIALS FOR BRIDGES

PAINTING AND TRAFFIC MARKING AND SIGNING

PAVEMENT SURFACE CHARACTERISTICS

SOILS AND STABILIZATION

T 42-10 (2015) Preformed Expansion Joint Filler for Concrete Construction

T 44-14 (2018) Solubility of Bituminous Materials

T 177-17 Flexural Strength of Concrete (Using Simple Beam with Center-Point

T 215-14 (2018) Permeability of Granular Soils (Constant Head)

T 42-10 (2015) Preformed Expansion Joint Filler for Concrete Construction

Release: Group 1 (April 2019)

BOX CULVERT, CULVERT PIPE, AND DRAIN TILE

METALLIC MATERIALS AND COATINGS FOR BRIDGES

PAINTING AND TRAFFIC MARKING AND SIGNING

PAVEMENT SURFACE AND STRUCTURE CHARACTERISTICS

MP 34-18 Materials for Sand Seals

NUMERICAL SEQUENCE TABLE OF CONTENTS

MP 31-17 Materials for Cold Recycled Mixtures with Emulsified Asphalt

TP 103-13 (2018) Detectable Warning Systems

TP 111-14 (2018) Measuring Retroreflectivity of Pavement Marking Materials Using a Mobile

TP 126-17 Evaluation of the Tracking Resistance of Hot-Poured Asphalt Crack Sealant by