V 29.03.

2017

user manual
 index

INDEX page page

introduction 3 enviromental care 44
on the wing 4 what have you bought 45
paraglider design 5 technical data 46
before first use 10 rigging scheme 47
free flights - launch 15 summary 49
free flights - flight 16
lfree flights - landing 18
lfree flights - winching 18
powered flights - launch 19
powered flights - climbing 23
powered flights - flight 25
different steering methods 29
steering influence on airfoil 30
powered flights - landing 33
powered flights - golden rules 34
quick descent methods 35
extreme manoeuvres 37
paraglider care 39
warranty and aerocasco 42

2
 introduction

Congratulations! < This paraglider on delivery meets all the requirements of the EN
926-1 and 926-2 regulations or has an airworthiness certificate
We are pleased to welcome you among the growing number of
issued by the manufacturer. Any alterations to the paraglider
DUDEK PARAGLIDERS pilots. You’ve become a proud owner of a
will render its certification invalid.
sport paraglider, designed according to recent trends among
< Other documents concerning this paraglider can be found on
paramotor canopies.
attached pendrive or on our website www.dudek.eu.
Extensive development, application of the modern production
methods and thorough testing resulted in a friendly behaving Note: Dudek Paragliders warns that due to the constant
!
paraglider, offering the pilot a lot of fun combined with great process of development the actual paraglider may differ
performance. slightly from the one described in the manual. However,
those differences cannot affect the basic design
We wish you many enjoyable and safe flying hours.
parameters: technical data, flight characteristics or strength.
Please read this manual carefully and note following details: In case of any doubts contact us please.

< The purpose of this manual is to offer guidelines to the pilot

using the paraglider. By no means it is intended to be used as a
training manual for this or any other paraglider.
< You may only fly a paraglider when qualified to do so or when
undergoing training at an accredited school.
< Pilots are personally responsible for their own safety and their
paraglider's airworthiness.
< The use of this paraglider is solely at the user's own risk! Neither
the manufacturer nor dealer do accept any liabilities involved.

3
 on the wing

For whom the Universal 1.1? resulting from considerable amount of reflex traits present in the
design.
Universal is the first free flying (EN B) paraglider ever which can be
converted by its user into a full-blood paramotor canopy On activating the trimmers and setting up the ALC+ steering,
(conforming to the DGAC standard). Universal 1.1 becomes a full reflex paramotor wing, good for both
leisure and cruise flying, thermalling, last but not least for initial
Universal us the first paraglider ever to smoothly and efficiently
paramotor training.
merge two aspects:
Universal 1.1 is refreshed version of its predecessor with upgraded
- nicely hadling free-flying paraglider (with EN/B certificate),
risers and new colour design in four elements schemes. Dominico
- full-blood paramotor canopy (conforming to DGAC standard). cloth is replaced by Porcher, colours of the lines are changed too
(according to PMA standards). We have modernized risers
Universal is dedicated for beginner and recreational pilots who fly:
equipment, make it more simple and comfortable. Basic
- exclusively free (but want to benefit from moderate reflex ability) parametres of the wing are the same.
- mostly free, sometimes with paramotor
- both free and paramotor As is the case of all our paragliders, the design draws on our long-
time experience, simultaneously incorporating state-of-the-art
- mostly with paramotor, sometimes free
technologies. The Universal is certified EN-B and LTF-B, and is in
- exclusively paramotor (but appreciate better economy, easier last stages of receiving paramotor (DGAC) certificates.
launch and nicer handling than in standard paramotor wing.
Universal is a great free-flying recreational paraglide. Beginning
pilots will surely appreciate exceptional comfort in uneasy thermals,

4
 paraglider design
trailing edge leading edge

cell inlets

rib

The Universal 1.1 is produced in new technology, utilizing capabilities

of precise laser cutter. All stages of the production process take place
suspension as our Polish plant under close supervision of the designer himself,
lines thus ensuring highest European quality.
Careful selection of modern fabrics and design solutions brings about
steering line
great strength and durability of the canopy.
All materials used come from marked production batches, and each
brake handle risers
production step can be verified down to identification of individual
harness worker and controller.
5
 riser scheme

ALC+ line TEA line

steering line

pulley loop (1)

TEA cleat
pulley in position (1)
lengthened

pulley loop (2)

Easy Keeper
covered swivel magnets ALC+
grommets
pulley loop (3)

trimmer
buckle
speed
brake
system
handle
pulleys
TST handle
trimmer speed
strap handle system
hooks

trimmer strap

lower carabiner
loop
upper
carabiner
loop

6
 riser scheme

For the Universal 1.1 we have chosen four-way risers equipped < TEA (Torque Effect Adjuster) - eliminates the engine
with: torque effect, shifting paraglider contrary to
propeller turn direction. The TEA system is
< ELR (Easy Launch Riser) system. It is a specially
adjustable.
marked A riser (with red cover);
< speed-system affecting A, B and C risers when engaged,
For quick and easy recognition in emergency, some of the risers are
featuring ball-beared pulleys and a dedicated line;
distinguished with coloured covers as follows:
< trimmers of red band marked with appropriate scale,
A - red (used for launching)
designed for easy and fast replacement in case of
A' - red (used for big ears)
deterioration;
B - yellow (used for B-stall),
< three levels of the pulleys, to be used depending on the D - blue (needed to keep the glider down in strong wind –
hangpoint level; aborted launch).
< ALC+  offers effective turning even at full
Other systems
speed, without excessive changes in the
profile (i.e. its stability). The steering part here is the separate This paraglider has no other systems which can be adjusted,
yellow line, fixed to proper steering lines which run to the exchanged or removed.
trailing edge.
< TST - (Tip Steering Toggle) - additional mini
steering handles fixed to the ALC+ lines.

7
 riser scheme

Easy Keeper is our indigenous way to hold

the brake handles at the risers by using
strong neodymium magnets. It keeps the
handles firmly at the risers, while both
attaching and releasing goes smoothly
and easily.
The system allows for easy placing the
brake handles on risers during flight, when
they are not used, thus minimalizing the
danger of getting into running propeller.

8
 toggle

Addressing different needs of our clients Neodymium magnet of the Easy Keeper swivel against twisting
we have created a TCT system - Triple of the steering line
Comfort Toggle, making it possible to
have your brake handles in rigid, half-rigid
or soft configuration without need to
purchase additional handles.

semi-soft rigid insert

PVC insert

slit for the inserts

The soft handle is obtained when no insert is used. exchangeable insert

9
 before first use

Operation Caution: Check your real take-off weight! Some pilots

! calculate their take-off weight by just summing up catalogue
Correct matching of the canopy and the paramotor belongs to the
numbers, e.g.: paramotor 29 kg + canopy 6 kg + pilot 87 kg
pilot.
= ca. 120 kg. In fact your actual take-off weight can be
Dudek Paragliders cannot take responsibility for all possible umpteen kilograms bigger. Most often we forget the
combinations, but if you contact us we are always ready to help. clothing, electronics, backpacks, sometimes even such basic
things like fuel or rescue chute weight are omitted!
Weight range
Each size of the canopy is certified for specific weight range, What harness?
meaning total take-off weight including the pilot, harness,
For free flying you can use any certified harness which has its
paramotor, equipment and the canopy itself.
hangpoints at 40-45 centimeters from the seatplate.The width
Exceeding maximum take-off weight described in technical data of between carabiners should be somewhere between 40 and 45 cm.
the paraglider (“Pilot’s weight incl. equipment”) increases risk of an
CAUTION: Please note that any modification of seat/hang
accident in case of pilot’s error.The smaller canopy area as ! point distance changes the position of the brakes as related
compared to take-off weight, the greater the risk.
to pilot's body. You must remember that in each harness
Paragliders considerably change their character due to increased your steering range will be different.
load and each experienced pilot should perfectly understand that.
The biggest danger induced by overloading the canopy is its
hyperreactivity.

10
 before first use

Adjustment of the steering handles, the pulley and the speed Before you will take on powered flight it is recommended to try the
system. setup out.
CAUTION! Before first use check whether steering lines and Hang up the entire PPG unit with ropes, sit in the harness and ask
! pulleys are set for higher or lower hangpoint, and adjust someone to pull the risers up. You must make sure that in flight you
them to your preferences if necessary. will always be able to reach the brake handles, even if the airflow
blows them away.
The Universal risers are shorter than in most paragliders, thus
alleviating potential problem with different hangpoints. There are Being suspended in this way you have a perfect opportunity to
four places to fix the steering lines pulley – upper lengthened adjust the speed system lines too. The speedbar when not in use
upper, lower, and middle (see risers diagram on p. 6). On the main must not pull the lines nor risers. Neither should it be too loose, for
steering line there are three points marked, indicating where to fix it could then get into rotating propeller.
steering handle depending on pulley placement.
An additional way to check the whole configuration out is to visit a
For free flying you shouls fix the pulley on the end of the extending take-off site in steady winds of ca. 3 m/s. With the engine off, inflate
loop, placed at the first upper hangpoints, and the steering handles the wing and take it up over your head.When it stabilizes, check
on upper positions marked on the steering lines (so that steering that the brakes are completely loose and do not affect the trailing
lines are effectively shortened). This is the factory setting of the edge. There should be a spare inch or so before they activate.
paraglider (unless ordered otherwise).
Remember that it is always safer to set the margin of play too big
See adjusting the pulley and steering line marks according to the than too small. And, most importantly, the setting must always be
hangpoints on next page. symmetrical.
Caution: Ill-adjusted steering lines can be a reason for
Generally speaking, upper hangpoints require longer steering lines, ! wrong assessment of the canopy state, and/or can cause
while the lower hangpoints – shorter lines.
dangerous deflations on high speeds when too short.

11
 before first use

How to match the pulley level and steering line mark

with the suspension height.

12
 before first use

Pulley in first position

1 2
Pulley in first position, EK
3 Pulley in second position 4 Pulley in third position
(upper lengthened), EK magnet mounted over (middle), EK magnet (lower), EK magnet
magnet mounted over buckle of the trimmer. mounted over buckle of mounted over buckle of
second pulley position. the trimmer. the trimmer.

13
 before first use

Pre-flight check < it is very important to check that no lines are looped around
the canopy. The so-called ”line-over” may have disastrous
Pre-flight check consequences during take off.
Having chosen a place to launch accordingly to the terrain as well < always put on and fasten your helmet before clipping in to
as wind speed and direction clear it of any obstacles that could the harness,
damage your canopy or tangle in the lines. < make sure that all quick links (maillons) of the risers are tight,

After laying out your paraglider in a horseshoe directed against the < Check main carabiners. They must be properly mounted,
wind following checks must be made: closed and locked.

< canopy, lines and risers condition. Do not launch if the < make sure the launch area is clear and free.
slightest damage is noticed, When launching with a paramotor, additionally check if:
< the paraglider should be arranged so that the centre section < the trimmers are properly set?
A-lines will strain earlier that the outer ones. This ensures easy < the TST handles are fixed to the risers?
and symmetrical launch, < nothing will collide with the propeller?
< the leading edge should stay taut and even, < full engine power is available?
< all lines and risers should be separated. Make sure they are
not tangled, and checked against catching anything. It is
equally important to check the brake lines. They must be
firmly attached to the brake handles and run freely through
the pulleys to the trailing edge,
< make sure the risers are not twisted,

14
 free flights - launch

Free flight Pump out possible faults and keep an eye on position of the
The main difference between the Universal and other paragliders is paraglider. Side drift is corrected best by moving yourself always
that due to its increased tuck-resistance (both during launch and under center of the canopy. In order to keep wing in the air the
flight) and greater speed range (when using the trimmers) it can be suspension lines must stay taut all the time, so in light winds you
safely flown in strong conditions too. will have to run forward. With stronger winds you can control the
wing while standing still.
Classic (forward) launch When leaving the ground apply some brakes, then release it after
Should be used with little or no wind. After pre-flight check, facing gaining some distance from the ground. Keep your hands relaxed.
the wind place the risers over your shoulders (A riser should lay on Reverse launch
top).
To be used when wind speed exceeds 3 m/s.
Clip it into carabiners and lock them. Grip the brake handles and
A-risers, holding them at the stitching, just under the quick-links. To After clipping the risers into carabiners as for the forward launch,
make things easier, A-risers have been markedwith a red cover. turn back to face the wing, moving one riser group over your head.
Spread out your slightly bent hands, keeping them down and back. As a consequence, you will have the risers crossed.

All other risers should be placed near your elbow joints. Unclip the brake handles from rear risers and grip it outside of the
risers without crossing neither arms nor lines. In this way you steer
Apply some tension to check if the A risers stay on top and the the left side with you left hand and vice versa. Now take
lines are not tangled. Take a step back, bow down a little and run corresponding A risers on both sides (still keeping brake handles in
forward. After the initial inflation smoothly move the hands with your hands).
the risers up and over your head until the wing will be directly
above you. Let the A risers loose and check the wing. Make sure that the wing inflates symmetrically and the lines are not
tangled. Building up tension with a few steps back and

15
 free flight - flight

simultaneously lifting the A risers (do not pull them towards you) Caution: During start, especially winched or with a motor,
!
will make the paraglider rise. always remember to bring the wing directly over your head.
The aerofoil and its angle of attack were arranged so as to
When it arrives over your head, stabilize it with the brakes, check
give maximum lift coefficient with relatively high safety level.
again if all
As a result it can stay behind a pilot, if he neglects bringing it
lines are clear and the cells inflated. directly over head during launch.
When turning into wind, remember to turn the right way
(hint: always do it the same direction) and to keep the lines strained Flight
at all times. The turn itself should be quick and smooth. While The increased speed range of Universal (in case of trimmers
3
turning you have to release the brake handles and grip them again operation) may demand some attention in flight. Nevertheless,
facing forward, so that again the left one is in the left hand etc. Last once you have mastered these additional assets, flying will become
check of the wing & free space to launch and off you go, running pure fun. Good handling will let you make best use of thermals,
into wind with eventual light braking when taking off. and increased speed on transitions means that your presence in
Remember! sinking air will be shorter. To avoid stalls when braking with closed
When deflating the canopy in strong winds (e. g. aborting a trimmers, their movement is restricted by the tape sewing.
launch), use the C risers, not the brakes. Using the brakes in strong Turns
wind can lift the pilot up and drag him/her back.
Brakes Universal 1.1 is an agile wing, with smooth reactions to all pilot’s
Caution: When clipping in the crossed risers, you can find actions. Handling is actually easy and forces grow proportionally to
! proper connection of the speed system particularly hard. Be position of the brakes. Adding some weight shift will make the
1 careful not to confuse the risers! paraglider turn really quick and tight.

16
 free flight - flight

The combined technique (weight shifting and brake input) is by far neither rock back nor surge forwards, but always stay above the
the most efficient method of turning. Turn radius is then determined pilot. In order to achieve it, the pilot should accelerate the canopy
by the amount of inside brake used and weight shift. Additional by letting off the brakes when entering a thermal (according to its
application a little outside brake after initiating the turn with strength) and brake it on exiting. This is part of basic active flying
maximum weight shift increases turn efficiency and the outboard that can spare you many potential collapses.
wing’s resistance to collapse (in turbulence, the edge of a thermal
When soaring the slope, minimum height of 50 m above the
etc).
ground is recommended for safety reasons. It is important to
In case of necessary turning in confined area at slow speed (e.g. comply with air traffic rules, especially when many pilots share
slope soaring), it is recommended to steer the decelerated canopy airspace close to the hill.
by loosening the brake at the outside of the turn while applying just
The avoidance manoeuvres often happen to be impossible in such
a little more brake on the inside.
conditions.
Caution: when entering a turbulent area you should brake
! Trimmers and speed-system operation
a little to put up the tension. It will allow you to react
instantly in case of a problem. Too hard or too quick pulling When flying into head wind or through sink it is advisable (for the
of one brake can cause the wing to enter a spin. sake of best glide angle) to increase speed, as long as conditions
are not too turbulent.
Thermalling and soaring
Full application of the speed system increases flight speed by some
When flying the Universal 1.1 minimum sink is reached with slight
30%. In contrast to most paragliders it does not decrease wing
brake pressure applied (10 to 15 cm, depending on pilot’s weight).
stability significant, but if you meet some serious trouble, it is
In turbulent conditions the canopy should be flown with a small
advisable to release the speedbar. The faster you fly, the more
amount of brake applied. This improves overall stability by
dynamic colapses can happen. With application of the speed
increasing the angle of attack of the canopy. The canopy should

17
 free flights - landing

system the brake forces increase, and brake effectiveness WINCHING

decreases.
Our paraglider has been successfully tested for foot launching by
At maximum speedbar and fully opened trims we strongly winch.
recommend steering with TST handles or TEA lines. Turns executed
During winching trimmers should be set in closed position (0).
in this way will be slightly wider, but strength needed to initiate the
turn will be smaller and there will be no decrease in speed. First phase of the winch take-off is analogous to classic launch.

Landing After rising the canopy you will be taken off the ground, as the
winch line gets loaded. Avoid large heading corrections in first
Just make sure that last turn into the wind is done with sufficient
stage of flight up to altitude of 50 meters.
altitude. At about 1 meter over ground flare out by gently braking
both sides. The glider may climb again for a while gaining some During this stage do not sit deep in the harness in order to be
height, if too much brake is used. ready for emergency landing in case of e.g. winch line break.

Caution: Strong wind landings hardly require braking, if at Make sure that your brakes are fully released, so that angle of
! all! Use D-risers to deflate the canopy after landing. Using attack does not increase above safe level.
the brakes will probably result in pilot being lifted again and During all winch it is recommended to control the direction by
dragged backwards. weightshifting only. Steering lines should be used only for
The final glide of the landing approach should be straight and considerable heading corrections, but even then do not pull them
smooth. Steep or alternating turns can result in a dangerous too much in order to avoid danger of stalling your wing.
pendulum effect near the ground.

18
 powered flights - launch

Adjust your heading regularly when winched, so no large First powered flights
corrections are necessary. Remember there are several In order to get familiar with your wing we recommend at first flying
conditions to be met when winching: with the trimmers closed since in this configuration the Universal
n pilot should be properly trained for winching, 1.1 behaves as a classic wing.
n the winch with all gear should be in good condition and Once you feel confident with your wing, you can start
specialized for paraglider winching, experimenting with faster trim settings and speed system. Use all
n the winch operator must be properly trained in winching and additional speed and vigor of the Universal 1.1.
servicing the gear,
Caution: Before each launch it is necessary to have a
n Universal 1.1 must not be winched with forces exceeding 90 ! thorough check of the paraglider, harness and power unit
daN, and under any circumstances must not be towed by any (see page 14).
vehicle not equipped properly or controlled by unskilled
operator.
Classic launch with no wind
Even when it seems that there is no wind at all, it is rarely so.
Therefore always be careful in determining the conditions, since in
PPG flying it is most important that the launch and initial climb are
performed with a head wind (the danger of losing your airspeed
while steep crossing of the wind gradient is greatly reduced then).
Special attention must be paid to trees, power lines and other

19
 powered flights - launch

obstacles, including the possibility of emerging rotors. propeller. On the other hand, possible fall on your back and
damaging the propeller is dangerous (and costly!) so it should be
Preparing the canopy
avoided at any price, even that of some damaged lines!
Lay out the paraglider downwind of the power unit, with all
During take-off, when you feel that the strain on both risers to be
suspension lines taut and pointing toward center of the power unit.
equal, open up full power and lean back to counter the engine
The risers are to be laid on the ground. Trimmers must be fully thrust, so that it can push you forward rather than towards the
closed (0). In strong conditions faster settings can be advised. Make ground. The best option is not to use the brakes, allowing the
sure that you warm up the engine while standing windward of the paraglider to rise as it was laid out. If it starts to swerve from its
wing. Stop the engine before clipping in the risers. Now run the course, just pull the opposite riser and run under
pre-launch checklist (see page 14).
the centre of the wing while observing starting direction. If the wind
When you are sure everything is OK, you can clip the risers in the lulls, give a stronger pull on the risers.
paramotor’s harness.
If the paraglider drops to one side or back too far to rise again, kill
Applying steady and equal pressure on both A risers move forward. the engine, interrupt launch and assess the conditions once again.
The wing practically does not overshoot, so the front collapses that As the wing rises, the forces grow lighter and it should stabilise
otherwise happen quite often during launches are rarely seen with above your head without overshooting. This is the best moment to
Universal 1.1. Instead it kind of waits for you to catch up. check if it is inflated in full and the lines are not tangled, but do so
neither stopping nor looking back over your shoulder. Once you
From now on you should steer the paraglider facing forward,
feel the forces on the risers decrease, run faster and let go of the
without looking back over your shoulders. When the canopy lies
risers. See if there is already any opposition on the brakes and, if
low behind you and you will try to turn, some lines can get in the

20
 powered flights - launch

necessary, use them to correct direction or to increase lift at take- Reverse launch in strong wind
off.
Reverse launch can be executed while holding in one hand both A
Remember:
risers and one brake, with throttle and the second brake in the
< If the cage of your power unit is not stiff enough, the risers other hand.
strained during launch can deform it to the extent of colliding
with the propeller. Before giving it full power, see that the cage With a decent wind it is by far the best way to launch.In weaker
did not catch any lines. wind it is better to prepare a classic launch, as running backwards
with a paramotor on your back is not the easiest thing to do. It is
< Any brake operation (or steering inputs in general) should be
reasonable not to pull the wing up until you are really determined
smooth and gentle.
to launch, especially when it’s already clipped in.
< Do not try to take off until you have your wing overhead.
Lay down the rolled paraglider with its trailing edge against the
Hitting the gas pedal before that can cause dangerous
wind. Unfold the wing enough to find the risers and check that no
oscillations.
lines are looped over the leading edge. Stretch the risers against
< Do not sit in the harness until you are sure you are flying! the wind, separating right and left one.
< The faster the trim setting is, the more brake input is required to
We suggest that you lay the risers in the same way as you will be
take off.
turning during reverse launch, and place one riser over the other,
< The lower the hangpoints of your power unit are, the easier is with rear risers upmost. It should be done this way because once
the launch. you clip in, the cage of your power unit will make turning on your
own practically impossible (with the canopy lying still).
Now run the pre-launch checklist (see page 14).

21
 powered flights - launch

After warming up the engine put the power unit on, turn to face < Do not try to take off until you have your wing overhead.
the wing, go to the risers and clip them in the appropriate Hitting the gas pedal before that can cause dangerous
carabiners. oscillations.
Pulling on the front and rear risers open the cells. It is a good idea < Do not sit in the harness until you are sure you are flying!
to pull up the wing briefly in order to check that the lines are not < The faster the trim setting is, the more brake input is required to
tangled. Holding the risers, brakes and throttle as described above, take off.
pull the front risers and inflate the canopy. The Universal 1.1 comes
up easily and sometimes may require a dab on the brakes to stop it Caution: When clipping in the crossed risers, you can find
over your head. ! proper connection of the speed system particularly hard.
Once you have it overhead, turn around, open the throttle and take Be careful not to confuse the risers!
off. As with the classic launch, in this case too you have to find such
combination of trimmers, brakes and throttle settings that will give
you the best speed and rate of climb.
Remember:
< You are launching with your hands crossed. You have to really
master this technique before trying it with a running engine on
your back.
< Any brake operation (or steering inputs in general) should be
smooth and gentle.

22
 powered flights - climbing

Climbing take-off you will notice a propeller torque (turning moment). It will
try to turn you around, so counteract with a brake or harness'
Once you took off safely, continue heading against the wind, using
cross-bracing.
brakes to correct rate of climb.
The risers of the Universal 1.1 feature double main carabiner loops
Do not try to climb too steeply - attempts to increase climb rate by
(upper and lower), as well as our TEA system. Asymmetric clipping
pulling the brakes will have an adverse effect, as due to additional
the risers and /or pulling the knot down through the tube are the
drag the actual rate of climb will worsen and with the throttle fully
ways to counter the torque effect when your paramotor is not
opened even a stall can occur.
equipped with cross-bracing. For the TEA system to work properly
In powered flight the Universal 1.1 behaves more like an aeroplane you have to adjust the stopping knot accordingly to the amount of
than a paraglider, and it is good idea to regard it as such.If there torque.
are no obstacles present, it is by far safer (and more impressive for
When climbing steeply with slow trim settings and high power
the spectators) to level for a while after take-off and gain some
output keep in mind the risk of stalling!
speed before converting it to height with a brief pull on the brakes.
Due to typical PPG feature - considerable vertical distance between
Another reason not to try climbing too steeply is the risk connected
thrust axis and wing chord - the range of safe power operation is
with engine failure at low altitude. Even as the Universal 1.1 in a
closely connected to your skills and equipment.
steep climb does not stay behind as much as conventional
paragliders do, the low speed is more likely to cause a stall. Power-unit induced oscillations
Besides, you should always be able to land safely in case of engine
Certain configurations of engine weight, output and propeller
malfunction, so it’s better not to take unnecessary chances and
diameter can cause serious oscillations, during which the pilot is
always fly with a safe margin of speed.
being lifted to one side by the torque effect, swings down due to
Depending on the power unit geometry, it is possible that after his weight, then is lifted again and so on.

23
 powered flights - climbing

To avoid this you can:

< before the launch clip the risers asymmetrically to the carabiners
TEA line non active (a) and active (b).
and/or
< change the throttle setting and/or
a b
< adjust the cross bracing to counteract the torque, if there is one
present and/or knot
< use the TEA, pulling down the knot through the tube,
simultaneously blocking it in the slit and/or
< shift yourself to the other side of the harness and/or
< change the trimmer settings,
The effect of turning the paraglider away from the propeller turn
< when in the ground clip in the risers unsymmetrically, using direction can be neutralised by the TEA or the additional inner loop
different carabiner hangpoints. show below, where the risers are clipped. However, there is no
The best method is to fasten opposite cross-bracing, or apply some adjustment there – in the TEA the knot can be put precisely where
weight-shift. Such oscillations usually occur at full power - the needed to completely stop the torque.
greater the engine output and propeller diameter, the bigger the
swings. In addition pilot reactions are often too late or wrong,
increasing the problem instead of solving it. In this case a simple way
to deal with this question is to close the throttle and release the
brakes. Especially less-experienced pilots tend to overreact. This is
called a pilot-induced oscillation, and proven solution is to leave the
brakes alone.
24
 powered flights - flight

Level flight Trimmers and speed-system operation

Once you have gained safe height after take-off and wish to go for The reflex airfoil of the Universal 1.1 means safe operation of the
a route, you can turn on the right direction, fully open the trimmers trimmers and speed-system in a wide range. You are free to
and let off the brakes.If the conditions are turbulent, it can look experiment with all possible settings, as long as you are on safe
foolhardy, but this is the essential feature of the reflex profile - the altitude.
faster you fly, the safer your Universal 1.1. That's why it’s actually
The trimmers belong to basic steering instruments. Their use
possible to release the brakes and enjoy your flight.
should be widely understood, nevertheless we woul like to
Caution: Some pilots with previous free-flying paragliders underline some basic rules concerning safety.
!
experience may have a well-grounded habit of keeping the
The trimmers must always be released (activated) symmetrically.
brakes slightly taut at all times. Such a technique, while quite
reasonable on a free-flying wings as it allows for quick pilot Full release of just one trimmer will cause the paraglider to enter a
reactions and decreases sink, is not advisable for reflex turn, and extreme cases can lead even to a spiral. A canopy reacts
paragliders. When you pull the brakes, the Universal 1.1 to unsymmetrical trimmers depending on its model and current
profile loses its reflex characteristics. take-off weight (the bigger weight, the more dramatic reaction).
If you happen to have a variometer or altimeter aboard – watch it. The only exception from the symmetric trimmer operation rule are
In a level flight it is very easy to start climbing unintentionally. The slight differences in settings necessary for course adjustments.
instruments will help you optimise speed and fuel economy.
When you intend to release the trimmers, follow this procedure:
Good knowledge of weather conditions (e.g. wind at different
< grab the trimmer buckles,
altitudes) and smart use of thermals, convergence and other kinds
of lift is another way of greatly reducing fuel consumption and < press the locks of both buckles with your thumbs,
increasing your flight range.

25
 powered flights - flight

< once you feel both locks to let go, allow the trimmer tapes to their movement has been restricted. (Note: it is physically possible
slowly slip out. to push the sewn trimmer tape through the buckle in order to
replace it, however in normal operation the trimmer must be pulled
In this way you will be able to release the trimmers as muchas you
up to the limiter only!)
intended to, in a controlled action.
Please note the wide operational speed envelope of the Universal
Closing the trimmers should be symmetrical too, pulling both
1.1 achieved by trimmers only. Due to such wide range we’ve
tapes simultaneously.
decided to introduce capability of restricting that range (before the
Trimmers must be activated on a safe altitude, with enough launch) by the pilot according to his skills and preferences. Even
margin for error. when the trimmer range is restricted by half, applying the speedbar
in urgent needs allows for almost maximum speed. Restricting the
In case of unsymmetrical trimmer release:
trimmer range is shown in „Adjusting the trimmers” appendix in this
< correct flight direction with a brake, manual.
< release the other trimmer (when altitude allows), or close the Always when you are flying at high speed, be it with released
previously released trimmer. trimmers or with additionally engaged speed system, your steering
inputs must be smooth, with no rapid movements. When
Trimmers and reflex profile
accelerated, the reflex wing canopy is often lacking support of the
Trimmers in the Universal 1.1 affect geometry of the airfoil. At rear line rows – they are loose. Rough yanking of steering handle
closed trimmers the airfoil features generates more lift with changes the pressure distribution and trimming of an airfoil. The
decreased reflex character. The more trimmer is released, the more airfoil can rapidly increase pitch and aggressive tuck will follow.
reflex there is.
Slow trimmer settings decrease sink and steering forces, so it is
In order to avoid stalls when braking with slow trimmer settings, possible to efficiently use the thermals.

26
 powered flights - flight

Study drawings of trimmers and speed-system adjustment and Speed and steering
setting, as well as their influence on the wing shape. We can discern three basic speed configurations (meaning setting of
the trimmers and the speed system operation):
Remember:
< Trimmer setting is another part of the pre-start check list! Trimmers completely closed (position 0):
< If it will be asymmetric, the wing will be constantly turning. < pilot uses the steering handles.

! Caution: Do not engage speed system with closed trimmers! Trimmers partly released (position 6 – risers level):
Such action can cause dangerous deflations! f you intend to
< pilot can use the steering handles, however with increased
use speed system, release at least 6 cm of the trimmer.
effort;
Speed system < steering the wing via TST handles will be definitively more

Directly affects the angle of attack and unlike the trimmer does not effective.
alter the airfoil geometry. Using full speedbar in case of the Trimmers fully released with or without speed system engaged:
Universal 1.1 increases speed by ca. 30%. Contrary to most of the < In this configuration pilot should not use main steering handles,
paragliders this is not connected with the stability loss, nevertheless
< flight direction may be corrected only with the TST handle or
when considerable turbulence is encountered the speedbar should
TEA line!
be released.
In order to retain stability of the wing, first thing to do is to release Caution: The safest way to change your course at high
the trimmer so that the alteration of the airoil is decreased or
! speeds is to use the TST or TEA especially in rough air.
completely aborted, and only the press the speedbar. If the
Turns executed in this way will be slightly wider, but the
trimmers stay closed, speed system will be inclining a modified
necessary steering force will be far lower, and speed will
airfoil.
not drop while turning.

27
 powered flights - flight

Any yanking or rapid deep pulling of the brakes can This warning is valid for any paraglider, the Universal 1.1
dynamically disturb the pressure distribution over the is no exemption here!
airfoil and therefore its actions.

Trimmer operation tips

In nil wind conditions the launch is easiest at completely closed
FAST trims. The stronger the wind, the more you can open the
trimmers. Nevertheless, launch on fast trim settings will be hard
or outright impossible (depending on wind speed).
closed released
MODIFIED FULL REFLEX
REFLEX AIRFOIL AIRFOIL Thermalling is most effective at closed trimmers. In case of strong
turbulence it is advisable to partly open the trims, thus increasing
overall stability.

Main brakes and the ALC can be used both simultaneously

and/or alternatively. The brakes will be more effective at slow
settings, while the ALC at faster ones.

ALC
Torque effect adjuster can be used for correcting flight direction in
fast configurations too (trimmers/speed system). It works the
same way as the TST used in our older paragliders.

28
 different steering systems

Steering with just the

1 2
Brake handle + TEA line
3 Steering with the TST 4 Steering with TEA line
brake handle (trimmers (trimmer partially only (trimmers partially or (trimmers partially or full
colsed - slow mode) released - accelerated full released - accelerated released - accelerated
mode) mode) mode).
29
 brakes influence on the reflex airfoil
Influence of brake operation on the reflex profile Released trimmers without using brakes
Typical configuration for fast and safe flying.Center of
pressures of the aerofoil moves forward, practically
excluding frontal collapses. Pitching moment increases
Pilots used to flying classic paragliders tend to the attack angle.
„active” piloting with their brakes always under
tension. Flying a reflex wing like that is not only Released trimmers with brakes applied
ineffective, but can be dangerous too. Even slight brake operation (especially when fully
accelerated) will move the centre of pressures
The basic rule of flying reflex paragliders says: the backwards, and the pitching moment will decrease the
more turbulent is the air encountered, the more trims angle of attack. Additionally, the airflow is considerably
should be released and use of regular brakes disturbed. In particular cases this can cause a collapse.
Steering can be necessary for heading corrections,
avoided (especially with speedsystem engaged).
nebertheless you should keep your brakes fully
Steering the paraglider in such configuration is most released when flying straight – otherwise the reflex
effectively done with TST handle (ALC+ line) or TEA feature will not work.
line, designed specifically with that use in mind..
Problem is demonstrated with following drawings. Closed trimmers
Using the brakes is a typical steering mode in this
configuration and does not cause any danger.This
setting is used during launch, landing and thermalling.
The canopy behaves much as classic profile paraglider,
with slightly increased tuck resistance.
lifg
pitching moment
speed
centre of pressures
sink

30
 speed modes

Trimmer settings influence on the airfoil

Trimmers colsed Trimmers in neutral position Trimmers fully released

- lowest speed, - neutral risers' length, - maximum speed

- minimum sink - in-the-middle position.
Launch confoiguration

A - 490 mm A - 490 mm A - 490 mm

A’ - 490 mm A’ - 490 mm A’ - 490 mm
B - 475 mm B - 490 mm B - 535 mm
C - 450 mm C - 490 mm C - 605 mm
D - 425 mm D - 490 mm D - 665 mm

Lengths of the risers incl. quicklinks, length tolerance +/- 5mm

D C B A' A D C B A'A D C B A' A

31
 speed modes

Trimmer settings influence on speed sysem action

Full acceleration on closed trimmers Full acceleration on completely released
trimmers

- offers good speed,light steering but - low angles of attack and maximum speed,-
decreased stability, high stability and hard steering,
- classic speed system operation - ALC+ (with TST toggles) or TEA steering
advised

A - 410 mm A - 410 mm
A’ - 410 mm A’ - 410 mm
B - 415 mm B - 460 mm
C - 420 mm C - 540 mm
D - 425 mm D - 665 mm

Lengths of the risers incl. quicklinks, length tolerance +/- 5mm

D C B A' A D C B A' A

32
 powered flights - landing

Landing rate and speed. Such an action is especially important when flying
with high surface loading.
Basically in PPG flying there are two kinds of landing: with and
without power.
Powered landing
Power off landing
Make a flat approach with the engine idling, then level out and lose
At an altitude of ca. 50 metres switch the engine off and glide as the speed before final flare. Immediately after touchdown switch
you would on a conventional paraglider. It reduces the chances of off the engine.
damaging the propeller on landing, but on the other hand there is
The main advantage of this procedure is of course the possibility of
only one attempt possible – it has to be done right!
a repeated approach if anything goes wrong. Still, if you forget to
Trimmers must be fully closed (0) or slightly released (2 to 3 cm), switch off the ignition before the wing falls down, there is
depending on individual preferences and weight of the pilot (same considerable risk of
position as you would for launching).
damaging propeller, catching lines in it or even suffering injuries
With or without power Universal 1.1 better copes with turbulence connected with falling on your running engine.
on partly open trimmers, so if the conditions are rough, better
Remember:
make an approach with greater speed, plan a lot of free space (as
< Whenever possible, get to know the landing field before taking
for a hangglider) and wear that speed off before touching down.
Universal preserves the energy well, so there is a long float off.
necessary, exchanging the abundant speed for lift with your brakes. < Check the wind direction before planning the approach.
< Landing with power off requires much less space.
If the landing field is not big enough and you have to land on the
spot, we advise you to set the trimmers in slower settings. It will < In case of any doubt, practice the landing until you feel totally

increase lift coefficient of the wing, effectively decreasing its sink safe.

33
 golden rules

Golden rules! < It is not reasonable to let go of the brakes below 100 meters,
< Never place the power unit downwind of the paraglider. because a possible power unit malfunction may require
< Check, double check and then check once again if there is no immediate attention.
fuel leakage. < In general never trust your engine, as it can stop at any

< Do you have enough fuel for the flight? It’s always better to take moment. Always fly as if it’s exactly what it's going to do.
too much than too little! < Unless it is absolutely necessary (e.g. collision avoidance), do

< Check if there is nothing loose in the harness, that could not execute tight turns against the torque direction. Especially
when climbing you can easily enter a stall and consequent
possibly contact the propeller in flight.
negative spin.
< Whenever you encounter a problem, fix it AT ONCE however
< Do not fly with tail wind at low altitudes, as it pretty much
small it is!
narrows your options !
< Always put on and lock the helmet before getting in the
< Do not wait for the problem to grow - any change of engine
harness.
sound or a vibration can indicate troubles. Land and check it
< Before each launch run a full pre-flight inspection.
out!
< After landing, control the wing facing the direction of flight,
< Be certain of your navigation.
since turning you always risk getting lines in the propeller. Turn
< Remember that not everyone is fond of your engine noise.
only if there is danger of falling on your back.
< Do not scare the animals.
< Do not ask for trouble - do not fly over water, between trees or
power lines etc., where engine failure will leave you helpless.
< Mind the turbulence caused by other gliders or even by
yourself, especially when flying low.

34
 quick descent methods

Quick descent methods B-Stall

Big Ears B-stal can be executed only with completely closed trimmers (i.e.
pos. ’0').
In order to get the big ears you have to pull down the outer lines of
the A' risers (red cover) by ca. 20-50 cm. While inducing big ears To enter a B-stall, simultaneously pull down both B-risers (yellow
you should never let the brakes out of your hands. After tucking cover) by ca. 10-15 cm. The canopy will collapse across the entire
the tips in, the Universal 1.1 will continue to fly straight with span along its B-row, the airflow over top surface will break and
increased sink rate (up to 5 m/s). You can steer the wing pretty projected canopy surface will be decreased.
efficiently by weight-shifting.
Forward movement will be almost completely stopped.
After releasing lines, the paraglider will usually open up on its own
Further pulling B-risers is not advised, as testes have shown it to
or you can assist it with a long stroke of the brakes, until the tips will
increase wing instability. If the canopy forms a horseshoe, gently
unfold.
pull both brakes to recover.
For the sake of safety (the possibility of a parachutal stall) it is
To exit a B-stall, the risers should be released in a smooth and
reasonable to engage speed system after pulling big ears in order
decisive manner.
to lessen the angle of attack. Executing big ears with opened
trimmers is very difficult due to reflex profile stability. On quick and symmetrical releasing B-lines the airflow will be
reinstated and the wing will surge forward, returning to normal
! Caution: Never try to pull big ears during powered climb, flight.The surge forward is minimal due to stability of thre reflex
as the increased drag of the ears can cause excessive angle profile, so braking is not necessary.
of attack and a parachutal stall. Besides, pulling the ears
while climbing is pointless anyway.

35
 quick descent methods

Spiral dive A typical reflex paraglider on released trimmers shows following

load distribution according to line rows: A=60%, B=30%, C=5%,
Universal 1.1 is an agile paraglider, so it enters spiral dive very
D=5%.
quickly and can surprise the less experienced pilot.
Taking over as much of the load by the A and B rows of the reflex
A spiral is characterised by reaching the highest sink rates possible. canopies (90% in total) brings about their praised stability.
Significant G-forces, however, make it difficult to sustain a spiral
However, in connection with a dynamic manoeuvre which a spiral
dive for a long time, as it can place high loads on both pilot and
dive is, it can shift the load dangerously close to its maximum value.
glider to degree of losing consciousness by the pilot. Never do this
Similar situation occurs when executing spirals or wingovers with
manoeuvre in turbulence or at too high bank angles.
big ears pulled. That’s another example of concentrating whole
Control the dive and do not exceed 16 m/s sink. If the dive is not load on reduced wing area, which - combined with high G
stopping after releasing the brake, assist the glider with the outer manoeuvres - shifts the peak loads unnecesarily close to their
one. maximum values.

Wing over
Caution: Never execute manoeuvres generating high G-
! You make a wingover by performing a series of consecutive,
forces (spiral dive, dynamic wimgovers etc.) on released
alternating turns with growing bank angle.
trimmers, as this is very dangerous!
Releasing the trimmers shifts the loading centre of the Too aggressive banking with unsufficient control can result with a
canopy forward, toward leading edge. This rule affects all massive collapse.
paragliders, but the more reflex is present in the airfoil, the
more aggressive is that effect.

36
 extreme manoeuvres

Aerobatics Extreme flying manoeuvres should only be carried out

during safety training courses (instability training) under
Universal 1.1 was not designed to do any aerobatics.
proper guidance!
Caution: All rapid descent techniques should be practiced
! One sided collapse
in smooth air and only with sufficient extreme manoeuvres
altitude margin! Full stalls and spins are to be avoided as When the trimmers are fully opened or the speed system is
they are not recommended techniques of clearing engaged, collapses practically do not occur and can be induced
dangerous situations. Irrespective of paraglider type they only by a very strong turbulence. Still, if it happens, a little counter-
may have dangerous consequences. steering is enough to keep the Universal 1.1 on course or at least
decrease a swing of the canopy toward collapsed side. Under
BY FAR THE BEST TECHNIQUE IS SAFE AND CORRECT
normal conditions with collapses up to 50% of the wingspan, the
FLYING, SO THAT YOU WILL NEVER
Universal 1.1 will reinflate instantly and spontaneously. If not, you
NEED TO DESCEND RAPIDLY!
should aid this process by application of a brake on the collapsed
side.

Extreme manoeuvres Frontal collapse

Caution: Due to high resistance of the Universal 1.1 against The reflex profile of the Universal 1.1 makes it practically impossible,
! both side and front collapses, we strongly recommend not especially at higher speeds. Any forced attempts can lead to
to provoke such situations at trimmers settings other than extremely deep collapses, so recovery will require decisive pilot
closed, even during safety trainings. Inducing collapses in action (short and equal application of both brakes).
standard way can be very hard to impossible, while Full stall and negative spin
unconventional attempts can result in extremely violent and
dynamic behaviour. May happen only as a result of serious neglect or intentional action

37
 extreme manoeuvres

of the pilot. You have to be careful when flying at very low speeds the matter. If it's not enough, try to untangle it with big ears or a
until fully familiar with brake operation. The canopy recovers stronger pull on the risers.
spontaneously in initial phase of stall, otherwise use standard
In case of any doubts you should seriously consider throwing the
procedures.
rescue chute.
Deep stall
Under normal conditions does not occur. If you want to prevent it at
Emergency steering
all, simply stick to a couple of rules:
In case of any malfunction that renders normal steering impossible,
< after B-stall, release the risers quickly and evenly. Don’t be afraid
you can safely steer and land Universal 1.1 using the D-risers (blue
– the Universal 1.1 does not jump forward excessively.
cover) or stabilo lines.
< after big ears execution, engage the speed system. This will
increase both the sink rate and safety margin, as big ears
constitute an effective aerodynamic brake with significant loss of
speed.
Nevertheless, if such a parachutal stall happens, simply apply some
pressure on speed bar and/or push the A risers forward.

Line over and cravatte

Universal 1.1 is a modern wing which, in order to decrease drag has
fewer suspension lines and greater distances between them.
Therefore it's always possible that after a tuck one of the stabilisers
may tangle in the lines. Usually a couple of pulls with a brake settles

38
 paraglider care

Cleaning and storage wing becomes damp even while lying on green grass in direct
sunlight, as the grass transpires.
Universal 1.1 design incorporates modern technologies, including
nylon lines in the leading edge. That’s why the paraglider should be Caution: Locking a wet paraglider in a car exposed to sun is
carefully packed, with proper conditions ensured for transport and
! absolutely unacceptable! Hot car interior acts like an oven
storage. and tests have shown that color bleeding/transfer can
Basic rules to be followed when folding the canopy: happen even at 50 Celsius degree. The warranty does not
cover such damages!
< Fold it accordion-wise rib to rib (cell by cell). Do not fold it by
halves, placing the stabilizers at the centerline. While drying, never expose your paraglider to direct sunlight
operation.
< When a compact package is created on the longest chord do
not roll it, but fold three to four times (depending on the chord Store the paraglider in a dry place, away from chemicals and UV
length) from trailing edge towards the leading one. exposure. Ideal storage temperature for the paragliders is 5 to 25
Celsius.
< The leading edge remains on top of folded canopy.

< Never pack you paraglider too tightly. Cleaning

< Optionally pack the wing into a dedicated WingShell. Clean the paraglider with water and a soft sponge. Do not use any
chemicals or alcohol, as these can permanently damage the fabric.

If you have completely prepared your gear but have to wait for Deterioration - a few tips
launch, a good idea is to use a quickpack, to protect your wing The paraglider is made mainly of Nylon - a fabric which, like any
against moisture and UV rays. Never pack or store the glider when other synthetic material, deteriorates through excessive exposure to
wet, as it significantly shortens life of the fabric.Remember that the UV rays that come with the sunlight.

39
 paraglider care

Hence it is recommended to reduce UV exposure to a minimum by Prevent lines from catching anything, as they can overstretch or
keeping the paraglider packed away when not in use. Even when tear. Never step on the lines.
packed in a bag, it should not remain in the sun for long.
Knots can chafe suspension and/or brake lines.
Suspension lines in this paraglider consist of Technora inner core
Check the length of your lines after tree or water landing, as they
and polyester sheath.
can stretch or shrink. The lines can be measured at the
Submitting them to excessive bending and loading in flight should manufacturer or an authorised workshop.
be avoided, as it can cause irreversible damage.
After landing in water you should check the wing fabric as well,
Please note that with frequent kiting on a field or a small hill your since the wave forces can cause the fabric to distort in some areas.
paraglider will deteriorate more quickly due to its repeated rising,
When taking the wing out of the water, always do this by trailing
falling and being dragged around.
edge. After a sea landing, rinse the paraglider with fresh water.
Uncontrolled strong wind takeoffs or landings can result in the
Since salt crystals can weaken the suspension lines even after
leading edge of the canopy hitting the ground hard, which may
rinsing in fresh water, you should replace the lines with new ones
seriously damage the ribs, sewing and surface cloth (including
immediately after contact with salt water. Frequent flying near
coating damage).
oceans and seas accelerates deterioration of the paraglider, as salt
Keep the paraglider clean, since getting dust in the lines and fabric present in the sea breeze can make the lines stiffen and even break.
will reduce their durability.
Be careful to keep snow, sand or stones from entering the cell
openings: their weight can slow or even stall the glider, while sharp
edges can damage the cloth.

40
 paraglider care

Repairs
Repairs should only be carried out by the manufacturer, authorised
distributor or an authorised workshop.
It is acceptable to fix minor cloth damage with self-adhesive
patches included in the package.

Inspections

Full Inspection is recommended every 24 months or every 150

hours whatever comes first, if not advised otherwise by the
inspecting person due to paraglider’s condition.

In case of paragliders used commercially (e.g. in schools or

tandem flying) a Full Inspection is recommended every 12 months
after first 24 months from purchase date or every 100 hours airtime
(whatever comes first).

A paraglider can be officially inspected only by the manufacturer or

a dealer (authorised to do so).

41
 warranty & aerocasco

We are aware that purchase of a new paraglider is a big expense Warranty does not cover any of the following:
for every pilot. That’s why we guarantee quality of our products, as < canopy colour fading as well as bleeding caused by improper
well as optionally we are offering a security system that will allow storage/transport
you to insure your paraglider against possible damage and repair
< damage caused by chemicals or salt water
costs with an AeroCasco insurance.
< damage caused by improper use

Warranty: < damage caused in emergency situations

Dudek Paragliders guarantees free of charge repairs in case of < damage resulting from accidents (airborne or otherwise)
damages caused by the material or production flaws:
Warranty is only valid if:
For the free-flying paragliders warranty
< flight hours can be identified basing on properly kept logbook
covers 36 months (3 years) or 300 flight hours,
of the owner (and his possible predecessors) with marked PPG
whatever comes first. If the free-flying
hours.
paraglider is used for
< the paraglider is used in accordance with the operating manual
powered flights, every hour flown is counted
double (not concerning PPG paragliders). < the owner did not make any repairs by him/herself (excl. minor
For the paramotor canopies (PPG) warranty repairs with self-adhesive patches)
covers 24 months (2 years) or 200 < the owner did not make any modifications
flight hours (whatever comes first). < the paraglider can be unmistakably identified by data
For the mountain wings (MPG), speedflying, sheet/sticker
schools or professional users warranty covers
< the paraglider has been properly inspected at all times.
18 months 1,5 year) or 150 flight hours (whatever comes first).

42
 warranty & aerocasco

Note: In case of damages caused by the material or AeroCasco covers only damages occuring while taking-off, flying or
i
production flaws please contact the dealer that sold you the landing. Obviously, all faults in the material and manufacturing
gear. The dealer will determine further actions. flaws are covered by normal warranty.
When handing the paraglider for the repair you have to present a
JIf you have bought the paraglider second-hand, ask previous
card confirming its AeroCasco status. After the repair you will have
owner for a copy of his logbook (covering entire entire use of ther
to cover only the share-of-cost value of 50 euro. AeroCasco is valid
paraglider from the day of original purchase).
for one repair only during covered time.
AeroCasco There is a possibility of extending AeroCasco for one further year.
Standard warranty does not cover repair costs To do this you have to send your paraglider for inspection to the
of damages caused by the user or a third party. manufacturer not later than a year after the date of purchase. The
Since costs of such repairs can be considerable, Dudek Paragliders AeroCasco extension fee is 75 EUR (including inspection).
offers an AeroCasco insurance. It offers a one time repair of any Remember to include the AeroCasco confirmation when you send
mechanical damage, no matter how big and who caused them. the paraglider for inspection.
The only expenses you will be facing are shipping costs and the AeroCasco does not cover any of the following: theft, canopy
share-of-cost amount. AeroCasco can be purchased for a brand discoloration, damages caused by incorrect storage damage ot
new paragliders only (at the purchase). The AeroCasco costs 50 transport, damages caused by chemicals, salt water or force
Euro. majeure.
Note: AeroCasco is not available for all paragliders (check
i before purchase). It can be purchased only for privately
used paragliders.

43
 environmental care

Environmental care
Paragliding is an outdoor sport.
We believe that our clients share our environmental awareness.
Exercising paragliding you can easily contribute to environment
preservation by following some simple rules. Make sure you are not
harming nature in places where we can fly. Keep to marked paths,
do not make excessive noise, do not leave any garbage and
respect fragile balance of the nature.

Recycling of used gear

A paraglider is made out of synthetic materials, which need to be
properly disposed of when worn out.
If you are not able to dispose of the paraglider properly, DUDEK
Paragliders will do that for you.Just send your paraglider to the
address given at the end of the manual, accompanied by a short
note.

44
 what have you bought

The Dudek paraglider you bought should include following ź USB drive with this manual
items: < small gifts
< a backpack and fastbag
< transport bag (with your canopy inside)
< the paraglider itself (canopy, lines and risers)
< compression strap to keep the canopy together
< speedbar (Easy Catch – optionally)
< wingshell (optionally).
< wind indicator (windsock or a strap)
< pocket with paper work and repair wallet including:
ź piece of self-adhesive fabric (10 cm x 37.5 cm) for small
repairs. Note that even small tears located in the vicinity
of stitches are to be repaired by an authorised service
only.
ź looped and stitched suspension line (the longest of all
lines in the paraglider) to be used as a temporary
replacement. Do not cut it if you have to temporarily
replace a shorter one, just tie it at the length needed.
ź paraglider passport with entered date of purchase and
valid technical inspection (please check the serial number
with the sticker on wing tip).

45
 technical data
Universal 1,1 23 25,5 28 31 34
Certification EN B B B B -
Approval DGAC* DGAC* DGAC* DGAC* DGAC*
Num ber of cells 50 50 50 50 50
Surface area (flat) [m 2] 23,00 25,50 28,00 31,00 34,00
Surface area (projected) [m 2] 19,83 21,98 24,14 26,72 29,31
Span (flat) [m ] 10,83 11,40 11,95 12,57 13,17
Span (projected) [m ] 8,71 9,17 9,61 10,11 10,59
Aspect Ratio (flat) 5,10
Aspect Ratio (projected) 3,83
Sink rate [m /s] min = 1,1 + - 0,2
Speed [km /h] min = 23; trim = 37 – 52; max = 57 + - 3
Max. cord [m m ] 2612,00 2751,00 2882,00 3033,00 3176,00
Min. cord [m m ] 601,00 633,00 663,00 698,00 731,00
Distance pilot to w ing [m ] 6,82 7,18 7,53 7,92 8,29
Total line lenght [m ] 344,01 362,82 380,74 401,20 420,70
Weight range EN [kg] 60-75 70-95 90-115 110-140 135-170
Weight range DGAC [kg] 60-95 70-115 90-140 110-170 135-215
Weight [kg] 5,60 5,95 6,40 6,85 7,35
Lines Technora: 90 & 140 & 190 & 280 & 340 & 420
Fabric Porcher Classic 38 g/m2 & Dominico tex 34 g/m2
Porcher Hard 40 g/m2
SR Scrim, SR Laminate 180 g/m2
Risers PASAMON - Bydgoszcz, Polska
46
 rigging scheme

The rigging scheme itself is published on the next page, while tables of line lengths you
will find in attachments to this manual.

Lengths are measured with a specialised, computer-operated device. All the lines before
measurement are stretched with a steady 5 kg load. Thanks to abovementioned device
and proper procedures, final tolerance of line lengths does not exceed +/- 10mm.

i Note: Distances given below are to be understood as

distances between connection points. When cutting a line for
repair, 20 cm extra must be added, as at each end a 10 cm
stitch is required to fix the loop. The only exception is the main
steering line (BRP), which is looped only at the upper end, with
at least 150 mm margin for fastening brake handle (this means
for this line extra 25 cm than in the table is needed).

47
rigging scheme

48
 summary

If you respect the rules of safe flying and proper glider care, you
will enjoy many years of pleasant airtime on your Universal 1.1.
Still, you must be aware of possible dangers and face them wisely.
You must accept the fact that all air sports are potentially
dangerous and your actual safety depends solely on you. We insist
that you fly safely,
and this concerns both the weather choicesafety margin during all
manoeuvres.

Caution: FLYING THE PARAGLIDER IS ALWAYS YOUR OWN

RESPONSIBILITY!

SEE YOU IN THE AIR!

49
 Dudek Paragliders
ul. Centralna 2U
86-031 Osielsko, Poland
tel. (+48) 52 324 17 40

www.dudek.eu
info@dudek.eu